Equivalent MIB Objects for VoIP show Commands
Available Languages
Contents
Introduction
This document covers the equivalent MIB objects that provide the pieces of information contained in various Voice over IP (VoIP) verification commands. NMS applications and/or scripts can potentially use this information.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
This document is not restricted to specific software versions. However, it is written specifically for a Cisco 3600 Series Router with an NM-2V card.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
Configuration
This output shows a relevant portion of the configuration that this document uses:
VoipRouter#show running-configuration Building configuration... Current configuration : 5412 bytes ! version 12.3 ... ! snmp-server community public RO ! ... ! voice-port 2/0/0 ! ... ! dial-peer voice 2000 pots destination-pattern 2000 port 2/0/0 ! dial-peer voice 1000 voip destination-pattern 1000 session target ipv4:172.16.99.22 ! ... end
VoIP Commands
These sections show the MIB objects that correspond to the output of these VoIP verification commands:
-
show voice port summary (for NM-2V card only)
-
show call active voice brief (for Cisco 3600 platform only)
-
show voice dsp (for NM-HDV card only)
The information that these VoIP verification commands contains can be extracted from IF-MIB, CISCO-VOICE-IF-MIB, CISCO-VOICE-ANALOG-IF-MIB, CISCO-VOICE-DIAL-CONTROL-MIB, DIAL-CONTROL-MIB, and CISCO-DSP-MGMT-MIB.
Note: In these examples, the Telephony leg is indexed by 1102799 and the H.323 leg is indexed by 1102966.
show voice port summary
Note: The bold text in the show voice port summary command is outlined in the Equivalent MIB Objects section.
VoipRouter#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
2/0/0(A1) -- fxs-ls(A2) up(A3)up(A4) off-hook(A5) idle y(A6)
2/0/1 -- fxs-ls up dorm on-hook idle y
Equivalent MIB Objects
A1 — IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0 A2 — CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1) A3 — IF-MIB::ifAdminStatus.37 = INTEGER: up(1) A4 — IF-MIB::ifOperStatus.37 = INTEGER: up(1) A5 — CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2) A6 — CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1)
Note: No MIB Object maintains the value contained in the CH portion of the show voice port summary command when the NM-2V card is used.
show voice call summary
Note: The bold text in the show voice call summary command is outlined in the Equivalent MIB Objects section.
VoipRouter#show voice call summary PORT CODEC VAD VTSP STATE VPM STATE ============ ======== === ==================== ====================== 2/0/0(B1) g729r8(B2) y(B3) S_CONNECT FXSLS_CONNECT 2/0/1 - - - FXSLS_ONHOOK
Equivalent MIB Objects
B1 — IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0
B2 — CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate.
1102966.1 = INTEGER: ietfg729r8000(25)
B3 — CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable.
1102966.1 = INTEGER: true(1)
Note: No MIB Object maintains the Voice Telephony Service Provider (VTSP) and VPM states individually. Use callActiveCallState from DIAL-CONTROL-MIB instead.
show dial-peer voice summary
Note: The bold text in the show dial-peer voice summary command is outlined in the Equivalent MIB Objects section.
VoipRouter#show dial-peer voice summary
dial-peer hunt 0
AD PRE PASS
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET PORT
2000(C1) pots(C2) up(C3) up(C4) 9(C5) 2000(C6) 0(C7) 2/0/0(C8)
1000 voip up up 1000 0 syst ipv4:172.16.99.22(C9)
Equivalent MIB Objects
C1 — CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90
— DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37
C2 — CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1)
C3 — IF-MIB::ifAdminStatus.37 = INTEGER: up(1)
C4 — IF-MIB::ifOperStatus.37 = INTEGER: up(1)
C5 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9
C6 — DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000
C7 — CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0
C8 — IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0
C9 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 =
STRING: ipv4:172.16.99.22
Note: No MIB Object maintains the value contained in the modem PASS THRU method portion of the show dial-peer summary command.
show call active voice brief
Note: The bold text in the show call active voice brief command is outlined in the Equivalent MIB Objects section.
VoIPRouter#show call active voice brief <ID>:<start>hs.<index> +<connect> pid:<peer_id> <dir> <addr> <state> dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes> IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late> delay:<last>/<min>/<max>ms <codec> MODEMPASS <method> buf:<fills>/<drains> loss <overall%> <multipkt>/<corrected> last <buf event time>s dur:<Min>/<Max>s FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n> sig:<on/off> <codec> (payload size) ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n> sig:<on/off> <codec> (payload size) Tele <int>:tx:<tot>/<v>/<fax>ms <codec> noise:<l> acom:<l> i/o:<l>/<l> dBm MODEMRELAY info:<rcvd>/<sent>/<resent> xid:<rcvd>/<sent> total:<rcvd>/<sent>/<drops> Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt: <type>/<manf> bw:<req>/<act> codec:<audio>/<video> tx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes> rx:<audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes> Telephony call-legs: 1 SIP call-legs: 0 H323 call-legs: 1 MGCP call-legs: 0 Total call-legs: 2 11D9 : 1102799(D1)hs.1 +1324 pid:2000(D2) Answer(D3) 2000(D4) active(D5) dur 1d19h(D6) tx:7875641(D7)/157512782(D8) rx:7875955(D9)/157519081(D10) Tele 2/0/0(D11):1: tx:157515460(D12)/157514630(D13)/0ms g729r8(D14) noise:-56(D15) acom:5(D16) i/0:-40(D17)/-46(D18) dBm 11D9 : 1102966hs.1 +1157 pid:1000 Originate 1000 active dur 1d19h tx:7875388/157507741 rx:7875641/157512782 IP 172.16.99.22(D19):19066(D20) rtt:6ms(D21) pl:157496940(D22)/4770ms(D23) lost:52(D24)/1(D25)/325(D26) delay:67(D27)/55(D28)/132ms(D29) g729r8 Telephony call-legs: 1 SIP call-legs: 0 H323 call-legs: 1 MGCP call-legs: 0 Total call-legs: 2
Equivalent MIB Objects
D1 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1
= Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC
D2 — DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000
D3 — DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2)
D4 — DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000
D5 — DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4)
D6 — DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks:
(1104123) 3:04:01.23
— DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16590203) 1 days,
22:05:02.03
D7 — DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641
D8 — DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782
D9 — DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955
D10 — DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081
D11 — IF-MIB::ifDescr.37 = STRING: Foreign Exchange Station 2/0/0
D12 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.
1102799.1 = Gauge32: 157515460 milliseconds
D13 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.
1102799.1 = Gauge32: 157514630 milliseconds
D14 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.
1102799.1 = INTEGER: ietfg729r8000(25)
D15 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.
1102799.1 = INTEGER: -56 dBm
D16 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.
1102799.1 = INTEGER: 5 dB
D17 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.
1102799.1 = INTEGER: -40 dBm
D18 — CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.
1102799.1 = INTEGER: -46 dBm
D19 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.
1102966.1 = IpAddress: 172.16.99.22
D20 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.
1102966.1 = INTEGER: 19066
D21 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.
1102966.1 = Gauge32: 6 milliseconds
D22 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.
1102966.1 = Gauge32: 157496940 milliseconds
D23 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.
1102966.1 = Gauge32: 1090 milliseconds
— CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.
1102966.1 = Gauge32: 3680 milliseconds
— CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.
1102966.1 = Gauge32: 0 milliseconds
D24 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.
1102966.1 = Gauge32: 52 packets
D25 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.
1102966.1 = Gauge32: 1 packets
D26 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.
1102966.1 = Gauge32: 325 packets
D27 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.
1102966.1 = Gauge32: 67
D28 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.
1102966.1 = Gauge32: 55 milliseconds
D29 — CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.
1102966.1 = Gauge32: 132 milliseconds
Note: The GapFill value of the show call active voice brief command is obtained when you add the SNMP Objects cvVoIPCallActiveGapFillWithSilence, cvVoIPCallActiveGapFillWithPrediction, and cvVoIPCallActiveGapFillWithInterpolation.
show voice dsp
VoIPRouter#show voice dsp
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
C549 009 01 {medium} 4.1.31 IDLE idle 0 0 1/0:0 05 0 0/36
02 {medium} 4.1.31 IDLE idle 0 1/0:0 06 0 0/0
03 {medium} 4.1.31 IDLE idle 0 1/0:0 07 0 0/0
04 {medium} 4.1.31 IDLE idle 0 1/0:0 08 0 0/0
C549 010 01 {medium} 4.1.31 IDLE idle 0 0 1/0:0 09 0 0/0
02 {medium} 4.1.31 IDLE idle 0 1/0:0 10 0 0/0
03 {medium} 4.1.31 IDLE idle 0 1/0:0 11 0 0/0
04 {medium} 4.1.31 IDLE idle 0 1/0:0 12 0 0/0
C549 011 01 {medium} 4.1.31 IDLE idle 0 0 1/0:0 13 0 0/0
02 {medium} 4.1.31 IDLE idle 0 1/0:0 14 0 0/0
03 {medium} 4.1.31 IDLE idle 0 1/0:0 15 0 0/0
04 {medium} 4.1.31 IDLE idle 0 1/0:0 16 0 0/0
C549 012 01 {medium} 4.1.31 IDLE idle 0 0 1/0:0 17 0 0/0
02 {medium} 4.1.31 IDLE idle 0 1/0:0 18 0 0/0
03 {medium} 4.1.31 IDLE idle 0 1/0:0 19 0 0/0
04 {medium} 4.1.31 IDLE idle 0 1/0:0 20 0 0/0
C549 013 01 {medium} 4.1.31 IDLE idle 0 0 1/0:0 21 0 0/0
02 {medium} 4.1.31 IDLE idle 0 1/0:0 22 0 0/0
03 {medium} 4.1.31 IDLE idle 0 1/0:0 23 0 0/12
04 g729r8 4.1.31 busy idle 0 1/0:0 24 0 176/56702
C549 014 01 {medium} 4.1.31 IDLE idle 0 0 1/0:0 01 0 0/27
02 {medium} 4.1.31 IDLE idle 0 1/0:0 02 0 0/12
03 {medium} 4.1.31 IDLE idle 0 1/0:0 03 0 0/12
04 {medium} 4.1.31 IDLE idle 0 1/0:0 04 0 0/12
Here are a few useful MIB Objects that provide information about the active call in the example output of the show voice dsp command:
CISCO-DSP-MGMT-MIB::cdspCardIndex.7 = INTEGER: 2 OLD-CISCO-CHASSIS-MIB::cardType.2 = INTEGER: hdv(516) OLD-CISCO-CHASSIS-MIB::cardDescr.2 = STRING: "High Density Voice" ENTITY-MIB::entPhysicalDescr.7 = STRING: High Density Voice ENTITY-MIB::entPhysicalDescr.22 = STRING: DSP (C549) CISCO-DSP-MGMT-MIB::cdspCardState.7 = INTEGER: normal(1) CISCO-DSP-MGMT-MIB::cdspCardMaxChanPerDSP.7 = Gauge32: 4 channels CISCO-DSP-MGMT-MIB::cdspTotalChannels.22 = Gauge32: 4 channels CISCO-DSP-MGMT-MIB::cdspActiveChannels.21 = Gauge32: 1 channels
Note: The MIB that contains the information for show voice dsp is CISCO-DSP-MGMT-MIB. However, due to Cisco bug ID CSCeb62542 for the NM-2V card, DSPs on NM-2V are not shown in ENTITY-MIB. Since cdspCardStatusTable is dependent on entPhysicalIndex of ENTITY-MIB, cdspCardStatusTable is not populated for the NM-2V card.
Appendix
This output shows the complete snmpwalk of ciscoVoiceAnalogIfMIB from CISCO-VOICE-ANALOG-IF-MIB at the time of the VoIP verification commands shown in this document:
snmpwalk -c public 172.16.100.20 CISCO-VOICE-ANALOG-IF-MIB:ciscoVoiceAnalogIfMIB CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.37 = INTEGER: ohms600Real(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgImpedance.38 = INTEGER: ohms600Real(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.37 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfCfgIntegratedDSP.38 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.37 = INTEGER: voice(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusInfoType.38 = INTEGER: none(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.37 = INTEGER: none(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfMaintenanceMode.38 = INTEGER: none(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.37 = Counter32: 0 CISCO-VOICE-ANALOG-IF-MIB::cvaIfStatusSignalErrors.38 = Counter32: 0 CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.37 = INTEGER: fxsLoopStart(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSCfgSignalType.38 = INTEGER: fxsLoopStart(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.37 = INTEGER: ringFrequency25(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingFrequency.38 = INTEGER: ringFrequency25(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.37 = INTEGER: offHook(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSHookStatus.38 = INTEGER: onHook(1) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.37 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingActive.38 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.37 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSRingGround.38 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.37 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTipGround.38 = INTEGER: false(2) CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.37 = INTEGER: 100 milliseconds CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingDigitDuration.38 = INTEGER: 100 milliseconds CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.37 = INTEGER: 100 milliseconds CISCO-VOICE-ANALOG-IF-MIB::cvaIfFXSTimingInterDigitDuration.38 = INTEGER: 100 milliseconds
This output shows the complete snmpwalk of ciscoVoiceInterfaceMIB from CISCO-VOICE-IF-MIB at the time of the VoIP verification commands shown in this document:
snmpwalk -c public 172.16.100.20 CISCO-VOICE-IF-MIB:ciscoVoiceInterfaceMIB CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.37 = INTEGER: true(1) CISCO-VOICE-IF-MIB::cvIfCfgNoiseRegEnable.38 = INTEGER: true(1) CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.37 = INTEGER: true(1) CISCO-VOICE-IF-MIB::cvIfCfgNonLinearProcEnable.38 = INTEGER: true(1) CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.37 = INTEGER: -38 dBm CISCO-VOICE-IF-MIB::cvIfCfgMusicOnHoldThreshold.38 = INTEGER: -38 dBm CISCO-VOICE-IF-MIB::cvIfCfgInGain.37 = INTEGER: 0 dB CISCO-VOICE-IF-MIB::cvIfCfgInGain.38 = INTEGER: 0 dB CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.37 = INTEGER: 3 dB CISCO-VOICE-IF-MIB::cvIfCfgOutAttn.38 = INTEGER: 3 dB CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.37 = INTEGER: true(1) CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelEnable.38 = INTEGER: true(1) CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.37 = INTEGER: 4 CISCO-VOICE-IF-MIB::cvIfCfgEchoCancelCoverage.38 = INTEGER: 4 CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.37 = INTEGER: normal(1) CISCO-VOICE-IF-MIB::cvIfCfgConnectionMode.38 = INTEGER: normal(1) CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.37 = STRING: CISCO-VOICE-IF-MIB::cvIfCfgConnectionNumber.38 = STRING: CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.37 = INTEGER: 10 seconds CISCO-VOICE-IF-MIB::cvIfCfgInitialDigitTimeOut.38 = INTEGER: 10 seconds CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.37 = INTEGER: 10 seconds CISCO-VOICE-IF-MIB::cvIfCfgInterDigitTimeOut.38 = INTEGER: 10 seconds CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.37 = STRING: "US" CISCO-VOICE-IF-MIB::cvIfCfgRegionalTone.38 = STRING: "US" CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.37 = INTEGER: 1 CISCO-VOICE-IF-MIB::cvIfCfgEntry.13.38 = INTEGER: 1 CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.37 = INTEGER: 1 CISCO-VOICE-IF-MIB::cvIfCfgEntry.14.38 = INTEGER: 1
This output shows the complete snmpwalk of ciscoVoiceDialControlMIB from CISCO-VOICE-DIAL-CONTROL-MIB at the time of the VoIP verification commands shown in this document:
snmpwalk -c public 172.16.100.20 CISCO-VOICE-DIAL-CONTROL-MIB:ciscoVoiceDialControlMIB CISCO-VOICE-DIAL-CONTROL-MIB::cvGeneralPoorQoVNotificationEnable.0 = INTEGER: true(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.1000 = INTEGER: 91 CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgIfIndex.2000 = INTEGER: 90 CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.1000 = INTEGER: voip(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgType.2000 = INTEGER: voice(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.1000 = INTEGER: active(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgRowStatus.2000 = INTEGER: active(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.1000 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCfgEntry.5.2000 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgSessionTarget.90 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDialDigitsPrefix.90 = STRING: 9 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgDIDCallEnable.90 = INTEGER: false(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgCasGroup.90 = INTEGER: -1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgRegisterE164.90 = INTEGER: true(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgForwardDigits.90 = INTEGER: -1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoicePeerCfgEntry.7.90 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionProtocol.91 = INTEGER: cisco(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDesiredQoS.91 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgMinAcceptableQoS.91 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgSessionTarget.91 = STRING: ipv4:172.16.99.22 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderRate.91 = INTEGER: g729IETFr8000(16) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxRate.91 = INTEGER: voiceRate(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgVADEnable.91 = INTEGER: true(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgExpectFactor.91 = INTEGER: 0 equipment impairment factor (eif) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIcpif.91 = INTEGER: 20 equipment impairment factor (eif) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgPoorQoVNotificationEnable.91 = INTEGER: false(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgUDPChecksumEnable.91 = INTEGER: false(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgIPPrecedence.91 = INTEGER: 0 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgTechPrefix.91 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgDigitRelay.91 = Hex-STRING: 00 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgCoderBytes.91 = INTEGER: 20 bytes CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgFaxBytes.91 = INTEGER: 20 bytes CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgInBandSignaling.91 = INTEGER: cas(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPPeerCfgEntry.23.91 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.90 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgIncomingDnisDigits.91 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.90 = INTEGER: -1 connections CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgMaxConnections.91 = INTEGER: -1 connections CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.90 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgApplicationName.91 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.90 = INTEGER: 0 CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgPreference.91 = INTEGER: 0 CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.90 = INTEGER: false(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgHuntStop.91 = INTEGER: false(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.90 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.6.91 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.90 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.7.91 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.90 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.8.91 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.90 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.9.91 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.90 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvPeerCommonCfgEntry.10.91 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveConnectionId.1102799.1 = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveTxDuration.1102799.1 = Gauge32: 157515460 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveVoiceTxDuration.1102799.1 = Gauge32: 157514630 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveFaxTxDuration.1102799.1 = Gauge32: 0 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveCoderTypeRate.1102799.1 = INTEGER: ietfg729r8000(25) CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveNoiseLevel.1102799.1 = INTEGER: -56 dBm CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveACOMLevel.1102799.1 = INTEGER: 5 dB CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveOutSignalLevel.1102799.1 = INTEGER: -46 dBm CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveInSignalLevel.1102799.1 = INTEGER: -40 dBm CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveERLLevel.1102799.1 = INTEGER: 5 dB CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveSessionTarget.1102799.1 = STRING: CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveImgPageCount.1102799.1 = Gauge32: 0 pages CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.13.1102799.1 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.14.1102799.1 = INTEGER: 2 CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.15.1102799.1 = INTEGER: 19971 CISCO-VOICE-DIAL-CONTROL-MIB::cvCallActiveEntry.17.1102799.1 = INTEGER: 5 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveConnectionId.1102966.1 = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteIPAddress.1102966.1 = IpAddress: 172.16.99.22 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRemoteUDPPort.1102966.1 = INTEGER: 19066 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveRoundTripDelay.1102966.1 = Gauge32: 6 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSelectedQoS.1102966.1 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionProtocol.1102966.1 = INTEGER: cisco(2) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveSessionTarget.1102966.1 = STRING: ipv4:172.16.99.22 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveOnTimeRvPlayout.1102966.1 = Gauge32: 157496940 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithSilence.1102966.1 = Gauge32: 1090 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithPrediction.1102966.1 = Gauge32: 3680 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithInterpolation.1102966.1 = Gauge32: 0 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveGapFillWithRedundancy.1102966.1 = Gauge32: 0 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveHiWaterPlayoutDelay.1102966.1 = Gauge32: 132 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLoWaterPlayoutDelay.1102966.1 = Gauge32: 55 milliseconds CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveReceiveDelay.1102966.1 = Gauge32: 67 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveVADEnable.1102966.1 = INTEGER: true(1) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveCoderTypeRate.1102966.1 = INTEGER: ietfg729r8000(25) CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLostPackets.1102966.1 = Gauge32: 52 packets CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEarlyPackets.1102966.1 = Gauge32: 1 packets CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveLatePackets.1102966.1 = Gauge32: 325 packets CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.21.1102966.1 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.22.1102966.1 = "" CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.23.1102966.1 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.24.1102966.1 = STRING: "172.16.99.22" CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.25.1102966.1 = INTEGER: 1720 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.26.1102966.1 = INTEGER: 1 CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.27.1102966.1 = STRING: "172.16.99.22" CISCO-VOICE-DIAL-CONTROL-MIB::cvVoIPCallActiveEntry.28.1102966.1 = INTEGER: 19066
This output shows the complete snmpwalk of ciscoVoiceCommonDialControlMIB from CISCO-VOICE-DIAL-CONTROL-MIB at the time of the VoIP verification commands shown in this document:
snmpwalk -c public 172.16.100.20 CISCO-VOICE-COMMON-DIAL-CONTROL-MIB: ciscoVoiceCommonDialControlMIB CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveConnectionId. 1102966.1 = Hex-STRING: 53 98 B1 3F EB B7 11 D7 80 02 AA AD C2 77 19 FC CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveVADEnable. 1102966.1 = INTEGER: true(1) CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCoderTypeRate. 1102966.1 = INTEGER: ietfg729r8000(25) CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveCodecBytes. 1102966.1 = INTEGER: 20 CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveInBandSignaling. 1102966.1 = INTEGER: cas(1) CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.6. 1102966.1 = "" CISCO-VOICE-COMMON-DIAL-CONTROL-MIB::cvCommonDcCallActiveEntry.7. 1102966.1 = INTEGER: 2
This output shows the complete snmpwalk of dialControlMib from DIAL-CONTROL-MIB at the time of the VoIP verification commands shown in this document:
snmpwalk -c public 172.16.100.20 DIAL-CONTROL-MIB:dialControlMib DIAL-CONTROL-MIB::dialCtlAcceptMode.0 = INTEGER: acceptAll(2) DIAL-CONTROL-MIB::dialCtlTrapEnable.0 = INTEGER: enabled(1) DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.1000.91 = INTEGER: voiceOverIp(104) DIAL-CONTROL-MIB::dialCtlPeerCfgIfType.2000.90 = INTEGER: voiceFXS(102) DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.1000.91 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgLowerIf.2000.90 = INTEGER: 37 DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.1000.91 = STRING: 1000 DIAL-CONTROL-MIB::dialCtlPeerCfgOriginateAddress.2000.90 = STRING: 2000 DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.1000.91 = STRING: DIAL-CONTROL-MIB::dialCtlPeerCfgAnswerAddress.2000.90 = STRING: DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.1000.91 = STRING: DIAL-CONTROL-MIB::dialCtlPeerCfgSubAddress.2000.90 = STRING: DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.1000.91 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgSpeed.2000.90 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.1000.91 = INTEGER: speech(2) DIAL-CONTROL-MIB::dialCtlPeerCfgInfoType.2000.90 = INTEGER: speech(2) DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.1000.91 = INTEGER: both(3) DIAL-CONTROL-MIB::dialCtlPeerCfgPermission.2000.90 = INTEGER: both(3) DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.1000.91 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgInactivityTimer.2000.90 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.1000.91 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgMinDuration.2000.90 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.1000.91 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgMaxDuration.2000.90 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.1000.91 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgCarrierDelay.2000.90 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.1000.91 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgCallRetries.2000.90 = INTEGER: 0 DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.1000.91 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgRetryDelay.2000.90 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.1000.91 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgFailureDelay.2000.90 = INTEGER: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.1000.91 = INTEGER: disabled(2) DIAL-CONTROL-MIB::dialCtlPeerCfgTrapEnable.2000.90 = INTEGER: disabled(2) DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.1000.91 = INTEGER: active(1) DIAL-CONTROL-MIB::dialCtlPeerCfgStatus.2000.90 = INTEGER: active(1) DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.1000.91 = Gauge32: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerStatsConnectTime.2000.90 = Gauge32: 0 seconds DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.1000.91 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsChargedUnits.2000.90 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.1000.91 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsSuccessCalls.2000.90 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.1000.91 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsFailCalls.2000.90 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.1000.91 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsAcceptCalls.2000.90 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.1000.91 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsRefuseCalls.2000.90 = Gauge32: 0 DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.1000.91 = "" DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectCause.2000.90 = "" DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.1000.91 = STRING: DIAL-CONTROL-MIB::dialCtlPeerStatsLastDisconnectText.2000.90 = STRING: DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.1000.91 = Timeticks: (1102966) 3:03:49.66 DIAL-CONTROL-MIB::dialCtlPeerStatsLastSetupTime.2000.90 = Timeticks: (1102799) 3:03:47.99 DIAL-CONTROL-MIB::callActivePeerAddress.1102799.1 = STRING: 2000 DIAL-CONTROL-MIB::callActivePeerAddress.1102966.1 = STRING: 1000 DIAL-CONTROL-MIB::callActivePeerSubAddress.1102799.1 = STRING: DIAL-CONTROL-MIB::callActivePeerSubAddress.1102966.1 = STRING: DIAL-CONTROL-MIB::callActivePeerId.1102799.1 = INTEGER: 2000 DIAL-CONTROL-MIB::callActivePeerId.1102966.1 = INTEGER: 1000 DIAL-CONTROL-MIB::callActivePeerIfIndex.1102799.1 = INTEGER: 90 DIAL-CONTROL-MIB::callActivePeerIfIndex.1102966.1 = INTEGER: 91 DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102799.1 = INTEGER: 37 DIAL-CONTROL-MIB::callActiveLogicalIfIndex.1102966.1 = INTEGER: 0 DIAL-CONTROL-MIB::callActiveConnectTime.1102799.1 = Timeticks: (1104123) 3:04:01.23 DIAL-CONTROL-MIB::callActiveConnectTime.1102966.1 = Timeticks: (1104123) 3:04:01.23 DIAL-CONTROL-MIB::callActiveCallState.1102799.1 = INTEGER: active(4) DIAL-CONTROL-MIB::callActiveCallState.1102966.1 = INTEGER: active(4) DIAL-CONTROL-MIB::callActiveCallOrigin.1102799.1 = INTEGER: answer(2) DIAL-CONTROL-MIB::callActiveCallOrigin.1102966.1 = INTEGER: originate(1) DIAL-CONTROL-MIB::callActiveChargedUnits.1102799.1 = Gauge32: 0 DIAL-CONTROL-MIB::callActiveChargedUnits.1102966.1 = Gauge32: 0 DIAL-CONTROL-MIB::callActiveInfoType.1102799.1 = INTEGER: speech(2) DIAL-CONTROL-MIB::callActiveInfoType.1102966.1 = INTEGER: speech(2) DIAL-CONTROL-MIB::callActiveTransmitPackets.1102799.1 = Gauge32: 7875641 DIAL-CONTROL-MIB::callActiveTransmitPackets.1102966.1 = Gauge32: 7875388 DIAL-CONTROL-MIB::callActiveTransmitBytes.1102799.1 = Gauge32: 157512782 DIAL-CONTROL-MIB::callActiveTransmitBytes.1102966.1 = Gauge32: 157507741 DIAL-CONTROL-MIB::callActiveReceivePackets.1102799.1 = Gauge32: 7875955 DIAL-CONTROL-MIB::callActiveReceivePackets.1102966.1 = Gauge32: 7875641 DIAL-CONTROL-MIB::callActiveReceiveBytes.1102799.1 = Gauge32: 157519081 DIAL-CONTROL-MIB::callActiveReceiveBytes.1102966.1 = Gauge32: 157512782 DIAL-CONTROL-MIB::callHistoryTableMaxLength.0 = INTEGER: 50 DIAL-CONTROL-MIB::callHistoryRetainTimer.0 = INTEGER: 15 minutes
Feedback