System Message Guide for Cisco Catalyst Series Switches, Cisco IOS XE Bengaluru 17.5.x

Cisco System Messages Overview

This document describes system messages for Cisco software releases. During operation, the system software sends these messages to the console (and, optionally, to a logging server on another system) during operation. Not all system messages indicate problems with your system. Some are purely informational, and others may help diagnose problems with communications lines, internal hardware, or the system software.

How To Read System Error Messages

System error messages begin with a percent sign (%) and are structured as follows:%FACILITY-SUBFACILITY-SEVERITY-MNEMONIC: Message-text

  • FACILITY is a code consisting of two or more uppercase letters that indicate the facility to which the message refers. A facility can be a hardware device, a protocol, or a module of the system software.

  • SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower the number, the more serious the situation. Table 1 lists the severity levels.

  • MNEMONIC is a code that uniquely identifies the error message.

  • Message-text is a text string describing the condition. This portion of the message sometimes contains detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table 2 lists the representations of variable fields and the type of information in them.

The following is a sample system error message:

%LINK-2-BADVCALL: Interface [chars], undefined entry point

Some error messages also indicate the card and slot reporting the error. These error messages begin with a percent sign (%) and are structured as follows:

%CARD-SEVERITY-MSG:SLOT %FACILITY-SEVERITY-MNEMONIC: Message-text

  • CARD is a code that describes the type of card reporting the error. VIP and FEIP are possible card types.

  • MSG is a mnemonic that indicates that this is a message. It is always shown as MSG.

  • SLOT indicates the slot number of the card reporting the error. It is shown as SLOT followed by a number (for example, SLOT5).

The prepended portion of the error message (%CARD-SEVERITY-MSG:SLOT) is not shown in the error message listings in this document.

Error Message Severity Levels

Error message severity levels correspond to the keywords assigned by the logging global configuration commands that define where and at what level these messages appear. The default is to log messages to the console at the debugging level (7). For more information, see the system configuration chapter and descriptions of the logging command in the configuration guide and command reference.

Level

Description

0 - emergency

System unusable

1 - alert

Immediate action needed

2 - critical

Critical condition

3 - error

Error condition

4 - warning

Warning condition

5 - notification

Normal, but significant, condition

6 - informational

Informational message only

7 - debugging

Appears during debugging only

Representation of Variable Fields in Error Messages

Representation

Type of Information

[atalk_address]

AppleTalk address

[atalk_net]

AppleTalk network, either 600 or 600-601

[char]

Single character

[chars]

Character string

[dec]

Decimal number

[enet]

Ethernet address (for example, 0000.FEED.00C0)

[hex]

Hexadecimal number

[inet]

Internet address (for example, 10.0.2.16)

[int]

Integer number

[node]

Address or node name

[sci_notation]

Scientific notation

[t-line]

Terminal line number in octal (or decimal if the decimal-TTY service is enabled)

[v-name]

VINES name; or number (hex or decimal)

Error Message Traceback Reports

Some messages describe internal errors and contain traceback information. This information is very important and should be included when you report a problem to your technical support representative.

The following sample message includes traceback information:

-Process= "Exec", level= 0, pid= 17 -Traceback= 1A82 1AB4 6378 A072 1054 1860

System Messages for Cisco IOS XE Bengaluru 17.5.x

Facility-Severity-Mnemonic

Severity-Meaning

Message

Message Explanation

Component

Recommended Action

PERF_MEASURE-2-CRIT_ERR

2-Critical

The Perf Measure protocol has encountered the critical error: [chars].

The protocol has run into a critical error. The reason should be given in the brackets.

perf-measure

LOG_STD_ACTION

PERF_MEASURE-4-ISSU_INCOMPATIBLE

4-Warning

\nperf-measure-issu-compat: returned FALSE

The compatibility checking has failed

perf-measure

LOG_STD_SH_TECH_ACTION

PERF_MEASURE-3-TRANSFORM_FAIL

3-Error

PERF MEASURE ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The PERF MEASURE ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the PERF MEASURE state between the active device and the standby device is not identical.

perf-measure

"show issu session <client_id> and " "show issu negotiated version <session_id>"

PERF_MEASURE-2-GET_BUFFER

2-Critical

PERF MEASURE ISSU client failed to get buffer for message. Error: [dec] [chars]

The PERF MEASURE ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

perf-measure

"show logging and show checkpoint client"

PERF_MEASURE-3-SESSION_UNREGISTRY

3-Error

PERF MEASURE ISSU client failed to unregister session information. Error: [dec] [chars]

The PERF MEASURE ISSU client failed to unregister session information.

perf-measure

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

PERF_MEASURE-2-INIT

2-Critical

PERF MEASURE ISSU client initialization failed to [chars]. Error: [dec] [chars]

The PERF MEASURE ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

perf-measure

LOG_STD_ACTION

PERF_MEASURE-2-SEND_NEGO_FAILED

2-Critical

PERF MEASURE ISSU client failed to send negotiation message. Error: [dec] [chars]

The PERF MEASURE ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

perf-measure

"show logging and show checkpoint client"

PERF_MEASURE-2-SESSION_REGISTRY

2-Critical

PERF MEASURE ISSU client failed to register session information. Error: [dec] [chars]

The PERF MEASURE ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

perf-measure

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PERF_MEASURE-3-INVALID_SESSION

3-Error

PERF MEASURE ISSU client does not have a valid registered session.

The PERF MEASURE ISSU client does not have a valid registered session.

perf-measure

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PERF_MEASURE-3-MSG_SIZE

3-Error

PERF MEASURE ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The PERF MEASURE ISSU client failed to calculate the MTU for the specified message. The PERF MEASURE ISSU client is not able to send the message to the standby device.

perf-measure

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

PERF_MEASURE-2-SESSION_NEGO

2-Critical

PERF MEASURE ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The PERF MEASURE ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

perf-measure

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IPX-2-RADIXINIT

2-Critical

Error Initializing novell path structure

A programming error has occured

novell

"Please ensure that sufficient memory required to load this " "image is available in this device. If memory requirements " "are met then follow the succeeding procedure. " LOG_STD_SH_TECH_ACTION

IPX-3-BADPATHS

3-Error

Invalid number of paths [dec] for %q

An internal inconsistency was detected in the IPX routing table\n\ structure.

novell

-

IPX-3-BADRDBDATA

3-Error

Inconsistency in the [chars] LSP Linkage data structure detected.

An internal inconsistency was detected in the RDB or SRDB\n\ internal routing table structure. Specifically a data area used by\n\ NLSP to link LSPs.

novell

"Copy and save this message. If NLSP is not running this could mean\n\ there is a software or hardware problem which is corrupting memory.\n\ If the message recurs copy and save the messages and call your\n\ technical support representative for assistance."

IPX-3-BADIGRPSAP

3-Error

Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help

An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch.

novell

"Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative."

IPX-3-BADIGRPSAPTYPE

3-Error

Unsupported SAP type for EIGRP being [chars] - type [hec]

-

novell

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the <bold>debug ipx sap activity<nobold> and <bold>debug ipx sap event<nobold> commands for the\n\ period during which this message appeared."

IPX-3-BADCOUNT

3-Error

Bad IPX server count. [chars] [dec] [chars] [dec]

The internal SAP service count does not match the number of services\n\currently present and displayed by the <bold>show ipx servers <nobold>command.

novell

"If this message recurs report the problem to your\n\technical support representative along with the output of the <bold>show\n\ipx servers<nobold> command taken before the message appeared and again after\n\ the message appeared."

IPX-6-NOVACCESSLOG

6-Information

[chars] [chars] [chars] [chars] [hec].[enet] [chars] [hec].[enet] [dec] pkt[chars]

If IPX access violation logging is enabled these messages are\n\ displayed when an access list logging event has occurred.

novell

"Verify that the host system is permitted or denied as defined in the\n\ access list."

IPX-3-TOOMANYNETS

3-Error

Too many networks. The number of directly connected IPX networks cannot exceed [dec]

The limit of connected IPX networks has been reached.\n\ Additional IPX interfaces cannot be configured.

novell

"Do not configure IPX on additional interfaces. \n\ Remove IPX configuration commands from inactive interfaces."

IPX-3-BADINSERT

3-Error

Duplicate SAP entry insert attempted. [chars][chars] [chars]0x[hec] [chars]0x[hec] [chars][dec] [chars]0x[hec] [chars]0x[hec] [chars]0x[hec]

An IPX SAP service entry which is being added currently already exists in\n\the current internal table.

novell

"Report the error messages and the tracebacks following them to your technical\n\support representative."

IPX-3-BADHASHTABLE

3-Error

Consistency check failed for SAP table [dec].

An internal SAP table consistency check failed.

novell

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IPX-3-NOVNOSTART

3-Error

IPX Failed to Start due to insufficient memory

The Novell IPX routing subsystem failed to initialize properly\n\ due to memory allocation errors usually due to insufficient\n\ amount of available memory.

novell

"Free up memory look for a possible memory leak or upgrade the\n\ system to have more memory."

IPX-7-DEBUGMSG

7-Debug

[chars]: %08x %08x %08x %08x %08x

Internal use only

novell

"Should not be seen in the field"

ETHER_CFM-3-CROSS_CONNECTED_CSI

3-Error

Service ID of received CC [chars] does not match local Service ID [chars].

For a given service within a domain the Service ID in the CC message should match the locally configured Service ID.

ethernet-cfm

"Verify that the service ID's are configured correctly using 'show ethernet cfm " "domain. "

ETHER_CFM-3-RCV_LOCAL_MPID

3-Error

MPID of CC matches local MPID.

The remote MPID matches a MPID configured locally for the service.

ethernet-cfm

"Either the local MPID or remote MPID should be changed as the MPID " " should be unique for a given service in a network"

ETHER_CFM-3-MEP_NOT_CONFIGURED

3-Error

received CC from unconfigured remote MEP.

While performing cross check a CC message was received from a remote MEP which is not configured under the domain submode.

ethernet-cfm

"Verify if the remote MEP should be added to the remote MEP list under the domain" " using 'show ethernet cfm domain."

ETHER_CFM-3-LR_FROM_WRONG_FP

3-Error

received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination

An unknown destination sent a reply to a Loopback messages that was intended to another device.

ethernet-cfm

"Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message."

ETHER_CFM-3-TM_EGRESS_BOUNDRY

3-Error

egress path found for TM is at a higher level than the traceroute message.

Traceroute found a domain boundry on egress since the egress port level is higher than the Traceroute Message level.

ethernet-cfm

"Check if the MIP level on the egress port is at appropriate level."

ETHER_CFM-6-ENTER_LCK_INT

6-Information

Interface [chars] enters LCK defect condition for [chars] direction

Interface is put in OOS state through exec cli for input direction

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_LCK_INT

6-Information

Interface [chars] exited LCK defect condition for [chars] direction

Interface has exited LCK defect condition.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-ENTER_LCK

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters LCK defect condition

Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_LCK

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited LCK defect condition

Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-ENTER_AIS_INT

6-Information

Interface [chars] enters AIS defect condition for [chars] direction

Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_AIS_INT

6-Information

Interface [chars] exited AIS defect condition for [chars] direction

LOG_STD_NO_ACTION

ethernet-cfm

"Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state"

ETHER_CFM-6-ENTER_AIS

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters AIS defect condition

Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_AIS

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited AIS defect condition

Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-5-IGNORED_VLAN

5-Notice

Ignored VLAN [dec] in '[chars]'

Invalid VLAN was ignored in the configuration.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-REMOTE_MEP_UP

6-Information

Continuity Check message is received from a remote MEP with mpid [dec] [chars] [chars] domain [chars] event code [chars].

A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MAID or CSIID

ethernet-cfm

"Information message only."

ETHER_CFM-3-REMOTE_MEP_DOWN

3-Error

Remote MEP mpid [dec] [chars] [chars] in domain [chars] changed state to down with event code [chars].

The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB

ethernet-cfm

"Check the remote CFM configurations using CFM " " utilities like traceroute and ping."

ETHER_CFM-3-CROSS_CONNECTED_SERVICE

3-Error

Continuity Check message with unmatched [chars] is received from a remote MEP with mpid [dec] [chars] level [dec] domain [chars] MAC: [enet].

The Continuity Check message whose CSIID or MAID is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network.

ethernet-cfm

"Configure the CFM CSI ID properly across the " "network."

ETHER_CFM-3-FORWARDING_LOOP

3-Error

Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the [chars].

The device is receiving its own CC messages for a particular vlan or evc within the same CSI or MA.

ethernet-cfm

"Configure the CFM maintenance points properly " "to avoid the forwarding loop."

ETHER_CFM-3-CONFIG_ERROR

3-Error

CFM miss-configuration in the network. Same mpid [dec] configured within the same maintenance name [chars] having [chars] for [chars].

The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MAID or CSIID.

ethernet-cfm

"Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association."

ETHER_CFM-3-CROSSCHECK_MEP_MISSING

3-Error

The device does not receive any CC messages from a remote MEP with mpid [dec] [chars] that it was expecting to be part of the [chars] in the domain [chars] from MAC: [enet].

The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MAID or CSIID.

ethernet-cfm

"There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. "

ETHER_CFM-3-CROSSCHECK_MEP_UNKNOWN

3-Error

The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the [chars] in the domain: [chars].

The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MAID or CSIID.

ethernet-cfm

"Check whether the CFM crosscheck configurations " "are proper."

ETHER_CFM-6-CROSSCHECK_SERVICE_UP

6-Information

The device received CC messages from all remote MEPs within a given [chars] in the maintenance domain [chars].

The service configured either CSI or MA is up as it receives CC messages from all remote statically configured MEPs.

ethernet-cfm

"Information message only."

ETHER_CFM-3-FAULT_ALARM

3-Error

A fault has occurred in the network for the local MEP having mpid [dec] vlan [dec] [chars] indicating a fault with the event code [chars].

This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEPP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other CSI or MA.

ethernet-cfm

"There could be a possible fault in the network. " "Check whether the cfm configurations are proper."

ETHER_CFM_HA-2-INIT

2-Critical

Ether CFM ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Ether CFM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ethernet-cfm

LOG_STD_ACTION

ETHER_CFM_HA-3-TRANSFORM

3-Error

Ether CFM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Ether CFM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether CFM state between the active device and the standby device is not identical.

ethernet-cfm

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_CFM_HA-3-MSG_NOT_OK

3-Error

Ether CFM ISSU client 'Message Type [dec]' is not compatible

The Ether CFM ISSU client received an incompatible message from the peer device. The message cannot be processed.

ethernet-cfm

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_CFM_HA-3-MSG_SIZE

3-Error

Ether CFM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Ether CFM ISSU client failed to calculate the MTU for the specified message. The Ether CFM ISSU client will not able to send the message to the standby device.

ethernet-cfm

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_CFM_HA-3-INVALID_SESSION

3-Error

Ether CFM ISSU client does not have a valid registered session.

The Ether CFM ISSU client does not have a valid registered session.

ethernet-cfm

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_CFM_HA-2-SESSION_REGISTRY

2-Critical

Ether CFM ISSU client failed to register session information. Error: [dec] [chars]

The Ether CFM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ethernet-cfm

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_CFM_HA-3-SESSION_UNREGISTRY

3-Error

Ether CFM ISSU client failed to unregister session information. Error: [dec] [chars]

The Ether CFM ISSU client failed to unregister session information.

ethernet-cfm

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_CFM_HA-2-SESSION_NEGO

2-Critical

Ether CFM ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Ether CFM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ethernet-cfm

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_CFM_HA-2-SEND_NEGO_FAILED

2-Critical

Ether CFM ISSU client failed to send negotiation message. Error: [dec] [chars]

The Ether CFM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ethernet-cfm

"show logging and show checkpoint client"

ETHER_CFM_HA-2-GET_BUFFER

2-Critical

Ether CFM ISSU client failed to get buffer for message. Error: [dec] [chars]

The Ether CFM HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly.

ethernet-cfm

"show logging and show checkpoint client"

SCVIF-2-DB_ENTRY_ALLOC_FAIL

2-Critical

SCVIF pair db entry allocation for interface [chars] failed

SCVIF pair database error. Memory chunk allocation for SCVIF pair database entry has failed.

service-controller

"Check for accurate memory management. " "Perform memory leak checks and " "look for memory corruption causes. " "Execute 'show proc memory' command."

SCVIF-2-DB_INSERT_FAIL

2-Critical

SCVIF pair db entry add for interface [chars] failed

SCVIF pair database error. Insertion of a new entry into SCVIF pair database has failed.

service-controller

"Check for accurate memory management. " "Perform memory leak checks " "look for memory corruption causes " "verify correct database management. " "Execute 'show proc memory' command."

SCVIF-2-DB_DELETE_FAIL

2-Critical

SCVIF pair db entry delete for interface [chars] failed

SCVIF pair database error. Removal of entry from SCVIF database has failed.

service-controller

"Check for accurate memory management. " "Perform memory leak checks " "look for mamory corruption causes and " "check for correct database management. " "Execute 'show proc memory' command. "

SCVIF-2-DB_ENTRY_FREE_FAIL

2-Critical

SCVIF pair entry free failed

SCVIF pair database error. Memory chunk free of SCVIF pair database entry has failed.

service-controller

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command."

SCVIF-2-DB_ALLOC_FAIL

2-Critical

SCVIF pair db allocation failed

SCVIF pair database error. Memory chunk creation for SCVIF pair database has failed.

service-controller

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command."

SCVIF-2-DB_DESTROY_FAIL

2-Critical

SCVIF pair database destroy failed

SCVIF pair database error. Memory chunk destroy has failed for SCVIF pair database.

service-controller

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute show proc memory command."

APPNAV_CONTROLLER-2-SC_SN_UNREACHABLE

2-Critical

APPNAV-CONTROLLER: Alarm #29007 Severity: Major. SN: [chars] is unreachable

Service context has entered Operational state and there is at least one configured node that is not part of the SN view.

service-controller

"Check status of configured SNs."

APPNAV_CONTROLLER-4-SC_SN_REACHABLE

4-Warning

APPNAV-CONTROLLER: Alarm #29007 cleared. SN: [chars] is reachable

Service Node is available

service-controller

"None. All is well"

APPNAV_CONTROLLER-5-SC_MIXED_FARM

5-Notice

APPNAV-CONTROLLER: Alarm #29003 Severity: Minor

When an appnav controller detects upon that there are other appnav-controllers/SNs in the cluster with different ICIMP/DMP minor version number.

service-controller

"Check versions of SNs in network."

APPNAV_CONTROLLER-5-SC_MIXED_FARM_CLEAR

5-Notice

APPNAV-CONTROLLER: Alarm #29003 cleared

There are no appnav-controllers/SNs with different ICIMP/DMP minor version number

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-SNG_UNAVAILABLE

2-Critical

APPNAV-CONTROLLER: Alarm #30001 Severity: Major. SNG: [chars] unavailable

No SN in appnav node group is available for optimization.

service-controller

"Check status of configured nodes."

APPNAV_CONTROLLER-4-SNG_AVAILABLE

4-Warning

APPNAV-CONTROLLER: Alarm #30001 Cleared SNG: [chars] available

SN's in appnav node group is available for optimization.

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-SNG_AO_UNAVAILABLE

2-Critical

APPNAV-CONTROLLER: Alarm #30000Severity: Major. In SNG: [chars] AO: [dec] is unavailable

No node in service node group is available for optimization and traffic is getting optimized by a secondary SNG.

service-controller

"Check status of configured SNs."

APPNAV_CONTROLLER-4-SNG_AO_AVAILABLE

4-Warning

APPNAV-CONTROLLER: Alarm #30000 cleared. In SNG: [chars] AO: [dec] is available

Service node group is available for optimization

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-SC_CONVERGENCE_FAILED

2-Critical

APPNAV-CONTROLLER: Alarm #29001 Severity: Major

CMM is not coming out of convergence state

service-controller

"Check connectivity between SN's and AC's"

APPNAV_CONTROLLER-4-SC_CONVERGENCE_SUCCESS

4-Warning

APPNAV-CONTROLLER: Alarm #29001 cleared

CMM convergence completed

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-SC_DEGRADED_CLUSTER

2-Critical

APPNAV-CONTROLLER: Alarm #29002 Severity: Critical. AC: [chars] is Degraded

Mismatch of stable AC views between AC's

service-controller

"Check connectivity between AC's"

APPNAV_CONTROLLER-4-SC_CLUSTER_STABLE

4-Warning

APPNAV-CONTROLLER: Alarm #29002 cleared. AC: [chars] is Stable

Mismatch of stable AC views between AC's

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-SC_SC_UNREACHABLE

2-Critical

APPNAV-CONTROLLER: Alarm #29006 Severity: Major. AC: [chars] unreachable

Connectivity with AC's under ACG is lost

service-controller

"Make sure AC's configured under ACG are up" " and reachable"

APPNAV_CONTROLLER-4-SC_SC_REACHABLE

4-Warning

APPNAV-CONTROLLER: Alarm #29006 cleared. AC: [chars] reachable

Connectivity with AC's under ACG is regained

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-SC_SN_EXCLUDED

2-Critical

APPNAV-CONTROLLER: Alarm #29008 Severity: Major. SN: [chars] excluded

Stable SN views across AC's are different. Those SN's that are not reachable by other AC's are exlcuded

service-controller

"Make sure excluded SN's are reachable from " "all AC's"

APPNAV_CONTROLLER-4-SC_SN_INCLUDED

4-Warning

APPNAV-CONTROLLER: Alarm #29008 cleared. SN: [chars] included

SN is reachable again

service-controller

"None. All is well"

APPNAV_CONTROLLER-2-ACG_IP_CHANGED

2-Critical

APPNAV-CONTROLLER: Alarm #10000 Severity: Major \nAppnav controller group IP address changed! All relevant service contexts will be disabled

Appnav controller group IP address changed! All relevant service contexts will be disabled

service-controller

"Change AppNav Controller's IP "

APPNAV_CONTROLLER-6-CM_REGISTER_SUCCESS

6-Information

AppNav registered with Central Manager successfully

Received a registration success message from the Central Manager

service-controller

"None. All is well"

APPNAV_CONTROLLER-3-CM_REGISTER_FAILED

3-Error

AppNav registration with Central Manager failed for the following reason: [chars]

Received a registration failure message from the AppNav Central Manager. AppNav has not registered with the Central Manager

service-controller

"Issue the " "<CmdBold>debug waas management errors<NoCmdBold> " "command and the " "<CmdBold>debug waas management events<NoCmdBold> " "Contact your Cisco technical support representative" " and provide the representative with the gathered information."

APPNAV_CONTROLLER-4-SERVICE_CTX_DISABLE

4-Warning

SERVICE-CONTROLLER: Alarm 10001 Severity: Major \n Disabling service context [chars]

Disabling service context

-

-

MDR_SM_LC-3-INIT_FAIL

3-Error

Initialisation error '[chars]'

During MDR SM initialisation an error has occurred that has rendered the MDR SM inoperable. an MDR operation will likely result in the resetting of this line card

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-NOTIFY_TIMEOUT

3-Error

Notification timeout for client [chars][dec] in state [chars]

During MDR SM state transition the notification timer expired for the client. Any MDR operation will likely result in the resetting of this line card

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-ABORT

3-Error

MDR state machine is aborted due to '[chars]'

MDR state machine is aborted due to an unrecoverable error. Any MDR operation will likely result in the resetting of this line card

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-SEMWAIT

3-Error

MDR state machine waiting for semaphore[chars] acquired by pid[dec]

SEMWAIT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-INVALID_EVENT

3-Error

MDR SM LC received an unexpected event [chars] in state [chars]

INVALID_EVENT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-ID_MISMATCH

3-Error

Client ID mismatch during progression on client: [dec] expecting [dec]

ID_MISMATCH_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-STATUS_INVALID

3-Error

Client [chars] [dec] returned an unexpected status code [dec]

STATUS_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-NO_FREE_EVENT_IN_QUEUE

3-Error

The event queue is full for MDR SM MDR SM will abort

NO_FREE_EVENT_IN_QUEUE_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-4-CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM LC client [chars] [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_PROXY-3-NOTIFY_TIMEOUT

3-Error

Notification timeout on MDR [chars] state machine for the remote client '[chars]'

MDR SM Proxy master is unable to communicate with its slave. It did not get any answer to the notification on the slave. An error has occurred that has rendered the MDR SM inoperable. An MDR operation will likely result in the resetting of all Line Cards.

mdr-sm

LOG_STD_ACTION

MDR_SM_PROXY-4-SYS_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM SYS client [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_PROXY-4-SLOT_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM Slot [dec] client [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-INIT_FAIL

3-Error

Initialisation error '[chars]'

During MDR SM initialisation an error has occurred that has rendered the MDR SM inoperable. an MDR operation will likely result in the resetting of all Line Cards.

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-QUIESCE_FAIL

4-Warning

Quiesce watchdog timer expired continuing with MDR

At switchover on the old Active RP the MDR SM enters the Quiesce state. While this is occuring the reload of the old Active is blocked which in effect blocks the switchover from taking place. Therefore to prevent a loss of service due to a bug in the MDR SM or one of its clients a watchdog timer ensures that we won't stay in this state for too long.

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-UNBLOCK_RF

4-Warning

MDR SM aborted continuing RF Progression [dec]

The MDR State Machine aborts due to a bug in the MDR State Machine or one of its clients. The RF progression was blocked it will be unblocked to allow the standby to boot

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_NO_FREE_EVENT_IN_QUEUE

3-Error

The event queue is full for MDR System SM MDR SM will abort

NO_FREE_EVENT_IN_QUEUE_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_NO_FREE_EVENT_IN_QUEUE

3-Error

The event queue is full for MDR Slot SM [dec] MDR Slot SM [dec] will abort

NO_FREE_EVENT_IN_QUEUE_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_NOTIFY_TIMEOUT

3-Error

Notification timeout on MDR system state machine for the local client [chars] [dec] in state [chars]

NOTIFY_TIMEOUT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_NOTIFY_TIMEOUT

3-Error

Notification timeout on MDR slot state machine [dec] for the local client [chars] [dec] in state [chars]

NOTIFY_TIMEOUT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_EVENT_TIMEOUT

3-Error

MDR slot state machine [dec] did not receive the SLOT_UP event from the linecard

Slot MDR SM did not get an expected event form the linecard. This error has rendered this slot MDR SM inoperable

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_CLIENT_ID_ERROR

3-Error

Can not find the data associated to client ID [dec]

CLIENT_ID_ERROR_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_CLIENT_ID_ERROR

3-Error

Can not find the data associated to client ID [dec] for slot [dec]

CLIENT_ID_ERROR_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_STATUS_INVALID

3-Error

Client [chars] [dec] returned an unexpected status code [dec]

STATUS_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_STATUS_INVALID

3-Error

Client [chars] [dec] on slot [dec] returned an unexpected status code [dec]

STATUS_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_CONTINUE_INVALID

3-Error

Client [dec] returned an invalid status code

CONTINUE_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_CONTINUE_INVALID

3-Error

Client [dec] returned an invalid status code on slot [dec]

CONTINUE_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_ID_MISMATCH

3-Error

Client ID mismatch during progression [chars] on client: [dec] expecting [dec]

ID_MISMATCH_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_ID_MISMATCH

3-Error

Client ID mismatch for slot [dec] during progression [chars] on client: [dec] expecting [dec]

ID_MISMATCH_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_NOTIFY_STANDBY_FAILED

3-Error

Failed to notify Standby for MDR system state machine Client [chars] [dec] in state [chars]

NOTIFY_STANDBY_FAILED_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_NOTIFY_STANDBY_FAILED

3-Error

Failed to notify Standby for MDR slot state machine [dec]

NOTIFY_STANDBY_FAILED_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_INVALID_EVENT

3-Error

Received an unexpected event [chars] in state [chars]

INVALID_EVENT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_INVALID_EVENT

3-Error

Slot [dec] received an unexpected event [chars] in state [chars]

INVALID_EVENT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_INVALID_ARG

3-Error

Process is unable to get his slot number

MDR State Machine creates one process per slot \ supporting MDR. In that case the process is \ unable to get his slot.

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-SYS_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM SYS client [chars] [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-SLOT_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM Slot [dec] client [chars] [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDNSPROXY-3-INIT_MDNS_FAIL

3-Error

[chars] Initialisation failure.

An internal error occurred during mDNS initialisation.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-PORT_RESERVED_MDNS

3-Error

[chars] Initialisation failure.

UDP Port 5353 Already reserved. Please disable the feature which uses 5353 and And Try Again.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-CHUNK_MEMORY_FAIL

3-Error

Chunk memory allocation failed

Chunk memory allocation failed for Cache element

mDNS

LOG_STD_ACTION

MDNSPROXY-3-API_FAIL_MDNS

3-Error

[chars] API failed

An error occurred while calling the APIs.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-NULL_CONTEXT_ID_MDNS

3-Error

Encountered a NULL context for the ID [dec]

NULL context for the ID passed in id_to_ptr.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-OS_API_FAIL_MDNS

3-Error

IOS API [chars] failed

Whitelist pattern length cannot exceed 100 for DSA snooping.

ios-scansafe

"This message is for informational purposed only"

CGC-0-CGC_EMERG

0-Emergency

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-1-CGC_ALERT

1-Alert

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-2-CGC_CRIT

2-Critical

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-3-CGC_ERR

3-Error

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-4-CGC_WARNING

4-Warning

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-5-CGC_NOTICE

5-Notice

[chars]

Normal but significant conditions

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-6-CGC_INFO

6-Information

[chars]

Informational messages

CGC_DDTS_COMPONENT

LOG_STD_NO_ACTION

CGC-7-CGC_ASSERT

7-Debug

Assertion Failure [chars] @[chars]:[dec] : [chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

TRANSCEIVER-6-REMOVED

6-Information

Transceiver module removed from [chars]

The online insertion and removal OIR facility detected the

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-6-INSERTED

6-Information

transceiver module inserted in [chars]

The online insertion and removal OIR facility detected a

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-3-CHECKSUM_ERROR

3-Error

Detected in the transceiver module in [chars] module disabled

A checksum error was detected when reading the ID PROM of a transceiver module for the interface specified in the error message. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. If the problem persists LOG_STD_ACTION."

TRANSCEIVER-3-IMPROPER_INSERTION

3-Error

Transceiver module in [chars] not fully inserted remove the transceiver and re-insert with proper seating lock.

An initialization failure occurred for the transceiver module for the interface specified in the error message. This condition is caused by improper insertion of transceiver As a result of the error the module is disabled.

spa-infra

"Try OIR'ing the module and reseat properly. "

TRANSCEIVER-3-INIT_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

An initialization failure occurred for the transceiver module for the interface specified in the error message. This condition could be caused by software firmware or hardware problem. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-NOT_COMPATIBLE

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is not compatible with the interface. As a result of the error the module is disabled.

spa-infra

"Replace the module with a compatible transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_IDENTIFIED

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message could not be identified and may not be compatible with the interface. As a result of the error the module is disabled.

spa-infra

"Replace the module with a compatible transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_SUPPORTED

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is not a cisco supported module. As a result of the error the module is disabled.

spa-infra

"Replace the module with a cisco supported transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-ATTACH_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

A software device driver attach failed. This condition could be caused by software firmware or hardware problem but a software or firmware problem is more likely. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-SM_CREATION_FAILURE

3-Error

Transceiver OIR State Machine creation failed for [chars] module disabled.

A state machine could not be created for the transceiver OIR operation. If a %SYS-2-MALLOCFAIL message was also received with this message this condition indicates insufficient system memory. Other possible causes include invalid subblock pointer.

spa-infra

"If it is insufficient system memory " LOG_STD_REDUCE_ACTION "If this message recurs " LOG_STD_ACTION

TRANSCEIVER-3-OPER_ENABLE_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

Failed to enable the transceiver module for the interface specified in the error message. This condition could be caused by software firmware or hardware problem. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-RPC_PROCESSING_ERROR

3-Error

Transceiver RPC error: [chars]

Non Fatal error occured in processing an RPC messsage.

spa-infra

show version

TRANSCEIVER-3-RPC_INIT_FAIL

3-Error

Transceiver RPC init failure

The system failed to create the resources required to process user\n\ interface commands for transceivers. The error is not fatal but some \n\ \show\ commands could fail.

spa-infra

show version

TRANSCEIVER-3-RPC_FAILED

3-Error

Application error rc = [dec] in port [chars]

The system failed to retrieve the information required to execute\n\ the comand

spa-infra

show version

TRANSCEIVER-3-DEV_PLUGGABLE_OPTICS

3-Error

Transceiver [chars] table internally inconsistent @ 0x[hec]

One of the transceiver attribute table is not properly updated.

spa-infra

"This is a debug message."

LIC_AGENT-3-MEMORY

3-Error

[chars]

License Agent subsystem has experienced a problem gettting the required \ memory to complete this operation.

lic_agent

"Check system memory for other memory allocation errors and contact \ Technical support for problem resolution. In the absence of IOS errors \ upgrading the memory in the network device may be required."

LIC_AGENT-3-UNKNOWN_EVENT

3-Error

event [dec] [chars]

License Agent tried to execute an unknown event.

lic_agent

"Contact technical support for problem resolution."

PCE-5-PCE_STATE

5-Notice

Connection to PCE server:[chars] [chars]

The connection to PCE server changed state.

-

"If the state change was unexpected check connectivity and state of the PCE server"

PCE-5-PCE_ERR_RX

5-Notice

PCEP peer [chars] sent PCError message - type: [dec] value: [dec]

PCErr message was received from peer

-

"Verify PCEP protocol operation"

SPA_PLUGIN-3-FIRMWARE_BADPATH

3-Error

[chars]: Invalid firmware file path [chars].

Specified fireware file path is invalid. This is a software error.

spa-ser-infra

LOG_STD_ACTION

SPA_PLUGIN-3-FIRMWARE_NOMEMORY

3-Error

[chars]: Insufficient memory for firmware file [chars] size [dec].

Can not allocate memory for firmware image for downloading to SPA.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-FIRMWARE_BADIMAGE

3-Error

[chars]: Firmware file [chars] read failed.

Firmware image pointed by the path is not valid.

spa-ser-infra

LOG_STD_ACTION

SPA_PLUGIN-3-FIRMWARE_DOWNLOAD

3-Error

[chars]: Firmware download failed.

Failed to download firmware image to SPA. It is caused by either lack of memory on SPA IPC failures improperly seated SPA or other download errors.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-FIRMWARE_DOWNLOADING

6-Information

[chars]: Downloading SPA firmware [chars]...

Downloading SPA firmware.

-

"None. Information only."

SPA_PLUGIN-3-FIRMWARE_STARTUP

3-Error

[chars]: Firmware startup failed. SPA status0x%08x host status0x%08x

Can not start Firmware image downloaded to SPA. Possible causes are either bad image on SIP flash disk hardware failures or outdated FPGA and/or ROMMON image.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FIRMWARE_APPS_DOWNLOAD

3-Error

[chars]: Firmware application download failed.

Failed to download application image to SPA. It may be caused by either lack of memory on SPA IPC failures improperly seated SPA or other download errors.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-FIRMWARE_APPS_DOWNLOADING

6-Information

[chars]: Downloading SPA firmware application [chars]...

Downloading SPA firmware application .

-

"None. Information only."

SPA_PLUGIN-3-FIRMWARE_APPS_STARTUP

3-Error

[chars]: Firmware application startup failed. SPA status0x%08x host status0x%08x

Can not start application image downloaded to SPA. Possible causes might be either bad image on SIP flash disk hardware failure or outdated FPGA and/or ROMMON image.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FILE_ERROR

3-Error

[chars]: Error accessing file [chars].

Specified file is not found lack of permission out of space or other file system/device errors.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FILE_TRANSFER

3-Error

[chars]: Failed to transfer file to or from SPA.

Failed to transfer a file to or from SPA. It might be caused by lack of memory on SPA or jacket card IPC failures improperly seated SPA or other errors.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-PLIM_CREATE

3-Error

[chars]: PLIM subblock creation failed.

Can not allocate memory for PLIM structure.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-NOPLIM

3-Error

[chars]: No PLIM subblock.

Invalid pointer was passed in. Can not dereference PLIM subblock pointer. Internal error.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-RETRY_EXHAUSTED

3-Error

[chars]: plugin initialization failedretries exhausted.

One or more critical conditions happened that prevented plugin initialization from moving forward after designated number of retries. Preceeding messages may indicated failure cause.

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FAILED

3-Error

[chars]: Plugin initialization failed.

Plugin initialization can fail for many reasons. Preceding messages may state the cause.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

spa-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-SPI4_CREATE

3-Error

[chars]: Device SPI4 creation failed.

Can not allocate memory for SPI4 structure.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-UART_CREATE

3-Error

[chars]: Device UART creation failed.

Can not allocate memory for UART structure.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-SPI4_SETCB

3-Error

[chars]: IPC SPI4 set callback failedstatus [dec].

Can not setup a callback function for SPI4 bus. It might be caused by improperly seated SPA outdated or a hardware failure.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-SPI4_SETCB_PORT

3-Error

[chars]: IPC SPI4 set callback failederror: [dec] for port [dec].

Can not setup a callback function for SPI4 bus for the specified interface port. It might be caused by improperly seated SPA outdated ROMMON/FPGA or a hardware failure.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-SPI4_CONFIG

3-Error

[chars]: Can not configure host side SPI4 profile.

SPI4 configuration from modular services card failed. It indicates either lack of system memory a hardware failure or an outdated ROMMON/FPGA image.

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-SPI4_NOTSYNC

3-Error

[chars]: Can not synchronize SPI4 bus.

SPI4 bus between modular services card and SPA is not synchronized. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image.

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-SPI4_SYNC

6-Information

[chars]: SPI4 bus synchronization achieved.

SPI4 bus between modular services card and SPA is synchronized.

-

"None. Information only."

SPA_PLUGIN-3-SPI4_INIT

3-Error

[chars]: SPI4 initializaion failed.

-

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-ENV_INIT

3-Error

[chars]: Environment monitoring initialization failed.

-

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-EFC_NOTSYNC

3-Error

[chars]: Can not synchronize EFC bus.

Extended flow control between modular services card and SPA is not synchronized. SPA is shut down. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image.

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-EFC_SYNC

6-Information

[chars]: EFC bus synchronization achieved.

Extended flow contorl between modular services card and SPA is synchronized.

-

"None. Information only."

SPA_PLUGIN-3-EXCEPTION

3-Error

[chars]: Exception with cause [dec].

One of SPA software components crashes.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-AUXC2W_CREATE

3-Error

[chars]: Device auxiliary C2W creation failed.

Can not allocate memory for auxiliary C2W structure.

-

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-4-LED_CREATE

4-Warning

[chars]: LED driver initialization failed.

Can not allocate memory for LED structure.

-

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-4-LED_READ

4-Warning

[chars]: LED read failed for port [dec] status [dec].

Can not read LED register values. It indicates either a not properly seated SPA or a hardware failure

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-4-LED_WRITE

4-Warning

[chars]: LED write failed for port [dec] status [dec].

Can not write to LED register. It indicates either a not properly seated SPA or a hardware failure

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-EEPROM_READ

3-Error

[chars]: Error reading EEPROM.

Can not read EEPROM content. It indicates either a not properly seated SPA or a hardware failure

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-IOFPGA_CREATE

3-Error

[chars]: Device IOFPGA creation failed.

Can not allocate memory for IOFPGA structure.

-

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-ROMMON

3-Error

[chars]: ROMMON reports error. SPA status0x%08x host status0x%08x.

ROMMON has reported a fatal condition during boot up. It may be caused by outdated ROMMON/FPGA images or defected hardware.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-NOPORT

3-Error

[chars]: Failed to open IPC port.

PLIM client IPC port has not been initialized.

spa-ser-infra

show ipc status

SPA_PLUGIN-3-ALLOC_ERR

3-Error

[chars]: Failed to allocate memory

Failed to allocate the required memory for the data

spa-infra

show ipc status

SPA_CCB-3-CMDFAIL_0ARG

3-Error

[chars]: host command [dec] error: [chars].

A command from host failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMDFAIL_1ARG

3-Error

[chars]: host command [dec]arg0=[dec] error: [chars].

A CCB command failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMDFAIL_2ARG

3-Error

[chars]: host command [dec]arg0=[dec] arg1=[dec] error: [chars].

A command from host failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMDFAIL_3ARG

3-Error

[chars]: host command [dec]arg0=[dec] arg1=[dec] arg2=[dec] error: [chars].

A command from host failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMD_TOOEARLY

3-Error

[chars]: host command [dec] received before handler ready.

Host command comes before handler is initialized

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-ENQUEUE_FAIL

3-Error

[chars]: host command [dec] failed to enqueue.

An error occurred while the SPA console was attempting to enqueue a host command to command queue.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-IF_CONFIG

3-Error

[chars]: IF_CONFIG type [dec] failed.

Interface configuration type not valid for SPA card.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-4-BADENCAP

4-Warning

[chars]: Unknown encapsulation command [dec].

An invalid encapsulation command is received by SPA. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SPA_MIB-4-DATA_LEN

4-Warning

[chars]: MIB message lengths mismatch[chars] expecting [dec] bytes receiving [dec].

MIB updates expect more data than received.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLIM-4-EXCEPTION

4-Warning

[chars] has experienced an exception: [chars]. Writing SPA crash dump information to [chars].

The local CPU in the specified slot indicated in the message has experienced the exception condition. The process that caused the exception might have been restarted. If an exception core dump was created core dump is stored in the SIP flash if available.

-

"If the system continues running normally no action is required. " "If this message recurs or system behaves abnormally please " "collect the crash dump file from SIP flash capture the output of " "the <CmdBold>show hw-module slot/subslot tech-support<NoCmdBold> " "command and open a case with the Technical Assistance Center via " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl."

SPA_PLIM-3-FW_RELOAD

3-Error

[chars] is being reloaded due to firmware/application exception.

Firmware application failed at SPA. The SPA is being reloaded to recover its operational state.

spa-ser-infra

"Collect the application core file from flash. Core file name is " "shown in the preceding message with timestamp."

SPA_PLIM-5-RECEIVINGFILE

5-Notice

Receiving [chars] from [chars] and storing to [chars].

SPA has sent a file syslog or core dump to RP and

-

LOG_STD_DBG_ACTION

SPA_PLIM-3-HEARTBEAT

3-Error

[chars] has experienced an heartbeat failure. Current Sequence [dec] Received Sequence [dec] Time since last keep [dec]ms.

The IPC communication between local CPU and host in the specified slot indicated in the message is not functional. The IPC module will be restarted. Following which communication might be re-established. If the problem persists the SPA will be reset.

-

"If the system continues running normally no action is required. " "If this message recurs or system behaves abnormally please " "collect the logs from the systemRP/SIP. Capture the output of "

SPA_PLIM-3-INITFAIL

3-Error

[chars] has failed initialization because SPA [chars].

A failure occurred during the SPA initialization. SPA is not functional and may be restarted by RP or SIP.

-

"If the SIP or RP successfully initialized the SPA " "no action is required. If the SPA was not successfully " "initialized " LOG_STD_ACTION

SPA_PLIM-3-INIT_PORT

3-Error

[chars] PLIM client IPC port has not been initialized.

-

spa-ser-infra

show ipc status

SPA_PLIM-3-FATALERROR

3-Error

SPA in slot [dec] bay [dec] experienced a fatal error [chars] and is being reset.

A fatal error was encountered during SPA operation. The SPA may be restarted.

-

"If the error is not observed more than once it might be " "a one off event and the SPA needs to be monitored. " "If the issue occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-4-SBE_ECC

4-Warning

[chars] reports [dec] SBE occurance at [dec] addresses

SPA has reproted single bit correctable ECC errors.

spa-ser-infra

"The log shows more than 1 SBE has occurred. " "SBEs are correctable memory problems. It will not affect router operation." "Excessive occurances indicate potential memory defections. Standard " "action is to watch at first occurance and replace at the first chance " "when recurs."

SPA_PLIM-4-SBE_OVERFLOW

4-Warning

[chars] SBE table[dec] elements overflows.

SPA has reproted more unique single bit correctable ECC errors than the platform defined internal table can hold.

spa-ser-infra

"Replace the fault memory chip at the earliest " "chance. SBEs are correctable memory problems. It will not affect router " "operation. Excessive occurances indicate potential memory defections."

SPA_PLIM-3-FILEFORWARD_FAIL

3-Error

[chars] failed to transfer a file from SPA to router flash due to IPC [chars].

A file transfer failed due to IPC errors. The file has not been stored in the flash.

spa-ser-infra

"Check flash disk for empty storage space. If it " "is short of space remove some files from the flash. If the message " "occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-3-FILECREATE_FAIL

3-Error

NULL

Check router and make sure it has installed removable flash card or disk e.g. <CmdArg>disk0:<NoCmdArg> <CmdArg>disk1:<NoCmdArg> <CmdArg>slot0:<NoCmdArg> etc.. If the flash is present make sure

spa-ser-infra

"Check router removable disk and make sure it has empty " "storage space. If the flash disk is short of space remove some files from " "the flash. If the message occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-3-FILE_NOTSTORED

3-Error

NULL

This error is seen when storing a file for a SPA to router removable flash failed. The partial file is removed from router removable flash.

spa-ser-infra

"If the error message occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-3-SW_ERROR

3-Error

NULL

-

spa-ser-infra

LOG_STD_ACTION

SPA_PLIM-3-ERRMSG

3-Error

[chars] [chars]

The error message in parentheses was logged by the SPA.

-

SPA_STD_SH_TECH_ACTION

SPA_DATABUS-3-SPI4_UNALIGNED_BURST

3-Error

[chars] [chars] - An error on the data bus has occurred.

In normal situation transitions from the Data Burst state to payload control or idle control are possible only on integer multiples of 8 cycles or upon end of packet. This error could happen if the MW bit flips on the bus with coincidental good dip4 or due to a misbehaving source.

spa-infra

"Power down and reseat the card. " SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SINGLE_DIP4_PARITY

3-Error

[chars] [chars] - A single DIP4 parity error has occurred on the data bus.

A single parity error has occurred on the data bus between the SPA and the SIP. When this condition is occurring a short duration of packet loss and/or symptoms resulting from data corruption may occur. This condition may indicate a developing hardware failure. This error should occur very infrequently during normal operation and should not occur when no changes are made to the configuration.

spa-infra

"Power down and reseat the interface card. " SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_OUT_OF_FRAME

3-Error

[chars] [chars] - A data bus out of frame error condition has occurred

An error has occurred on the data bus between the SPA and the SIP. When this condition is occurring the interface will be down and/or not forward any traffic.

spa-infra

"Power down and reseat the card. " SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SEQUENCE

3-Error

[chars] [chars] - A sequence error has occurred.

A sequence error has occurred on the data bus between the SPA and the SIP. When this condition is occurring a short duration of packet loss may be noticed. This condition may indicate a developing hardware failure. This error should occur very infrequently during normal operation and should not occur when no changes are made to the configuration.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-PACKET_GAP_ERROR

3-Error

[chars] [chars] - A packet gap error has occurred

The data bus interface on this line card is experiencing a hardware-related issue. No loss of data or data corruption should occur. Packets should continue to be forwarded.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SINGLE_DIP2_PARITY

3-Error

[chars] [chars] - A single DIP 2 parity error on the FIFO status bus has occurred.

The data bus interface on this line card is experiencing a hardware-related issue. Some packets may be dropped.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_FIFO_STATUS_BUS

3-Error

[chars] [chars] - FIFO status bus out of frame condition has occurred.

The data bus interface on this line card is experiencing a hardware-related issue. When this condition is occurring the interface will be down and/or not forward any traffic.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_BAD_CHAN_NUM

3-Error

[chars] [chars] - An error condition on the SPA data bus has occurred.

An error condition on the SPA data bus has occurred. This condition can be caused by a software fault only.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_DATABUS-3-SPI4_CALENDAR_LEN

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. This condition results from a software fault.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_DATABUS-3-SPI4_CRTL_WD_NO_DIP4

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

This message points to an error condition on the SPA data bus. Symptoms of this error include data corruption and/or a short duration of data loss.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_BAD_CNTR_WORD

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. Symptoms of this error include data corruption and/or a short duration of data loss. In addition the interface may lock up.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SINK_FIFO_OVERFLOW

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. Possible causes include misconfiguration of Maxburst parameters incorrect FIFO sizing or FIFO threshold settings.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_DATABUS-3-SPI4_SINK_FIFO_UNDERRUN

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. Possible causes include misconfiguration of Maxburst parameters incorrect FIFO sizing or FIFO threshold settings.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_CONSOLE-3-NOBUF

3-Error

No packet buffer available for sending SPA console messages

An error occurred while the SPA console was attempting to acquire a packet buffer from the IPC buffer pool.

-

show ipc status

SPA_CONSOLE-5-CANTSEND

5-Notice

Cannot send SPA console messages.

An error occurred while a SPA console message was being sent via the IPC. This condition might result in a malfunction in the operation of the IPC.

-

show ipc status

SPA_CONSOLE-5-CANTGET

5-Notice

Cannot get SPA client IPC port

SPA console sub-block is not initialized properly.

-

LOG_STD_ACTION

SPA_CONSOLE-5-CANTSET

5-Notice

Cannot set SPA client IPC port.

SPA console sub-block is not initialized properly.

-

LOG_STD_ACTION

SPA_CONSOLE-3-INITFAIL

3-Error

[chars]: SPA console initialization error: [chars].

A failure occurred during initialization of the SPA console subsystem. The SPA console may not be functioning.

-

LOG_STD_ACTION

SPA_CONSOLE-3-BADDETACH

3-Error

SPA console session detach failed with IPC error [chars].

A failure occurred when attempting to detach SPA console subsystem.

-

LOG_STD_ACTION

SPA_CONSOLE-5-QUEUEFULL

5-Notice

Queue holding SPA console messages is full current console packet will be dropped

An error occurred while the SPA console was Queueing a packet for transmission. Some console data may be lost

-

show ipc status

SPA_CONSOLE-3-TX_BUS_PARAM

3-Error

[chars]: VCON_SPACP: Invalid SPA bus parameters.

There was an error sending a message to SPA.

c7600-ssc-600

LOG_STD_RECUR_ACTION

SPA_CONSOLE-3-RX_BUS_PARAM

3-Error

[chars]: VCON_SPACP: Invalid SPA bus parameters.

There was an error receiving a message from SPA.

c7600-ssc-600

LOG_STD_RECUR_ACTION

SPA_CONSOLE-3-NO_DRIVER

3-Error

[chars]: VCON_SPACP: Driver not ready.

SPA sent a message before SIP was fully initialized.

c7600-ssc-600

LOG_STD_RECUR_ACTION

SPA_HA-3-BADSWITCHOVER

3-Error

[chars]: Invalid HA event detected: [chars]

HA switch over event comes before finishing inialization.

-

LOG_STD_SH_TECH_ACTION

BEEP-3-SLOG_LINE

3-Error

[chars] [chars]

This is an internal BEEP library error message.

beep

LOG_STD_ACTION

BEEP-3-SLOG_LINE_TB

3-Error

[chars] [chars]

This is an internal BEEP library error message.

beep

LOG_STD_ACTION

BEEP-3-SESSION_ERR

3-Error

[chars] at [chars]:[dec]

The BEEP subsystem had an error and may stop running.

beep

LOG_STD_ACTION

SPA-3-BAD_FCITYPE

3-Error

[chars]: Illegal FCI type [dec].

An invalid FCI type is passed to SPA. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SPA-3-INITFAIL

3-Error

Initialization error

A failure occurred during the initialization.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-ENTITY_INITFAIL

3-Error

SPA entity initialization error

A failure occurred during the SPA entity management subsystem startup. Entity management is not enabled.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-SW_ERROR

3-Error

NULL

-

spa-infra

LOG_STD_ACTION

SPA-3-ENVMON_INITFAIL

3-Error

SPA environmental monitoring initialization error

A failure occurred during the SPA environmental monitoring subsystem startup. Environmental monitoring is not enabled.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-ENVMON_NOT_MONITORED

3-Error

Environmental monitoring is not enabled for [chars]

The indicated SPA has not registered any sensors with the environmental monitoring system.

-

LOG_STD_SH_TECH_ACTION

SPA-4-TEMP_WARNING

4-Warning

[chars] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-2-TEMP_CRITICAL

2-Critical

[chars] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP Please correct immediately.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-0-TEMP_SHUTDOWN_OVR

0-Emergency

[chars] temperature too high on sensor [dec] [dec]C but shutdown has been

MSG_SPA_TEMP_HIGH_EXP SPA shutdown has been overridden by configuration

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-0-TEMP_SHUTDOWN

0-Emergency

[chars] temperature too high on sensor [dec] [dec]C. SPA has been shut down.

MSG_SPA_TEMP_HIGH_EXP The SPA has been shut down.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-4-TEMP_WARNLOW

4-Warning

[chars] temperature too low on sensor [dec] [dec]C.

SPA temperature too low. Component reliability and data integrity may be compromised.

-

"Raise the ambient temperature if it is too low. If there is no " "issue with the ambient temperature then the SPA temperature sensor has " "likely failed. If there are no data errors this warning can be " "ignored."

SPA-4-POWER_WARNING

4-Warning

[chars] power consumption [dec] Watts is higher than typical max value of [dec] Watts.

SPA power consumption is higher than the typical max value. Component reliability and data integrity may be compromised.

-

"Check for the total power available for the system. If " "there is sufficient power availabe this condition may not have " "any adverse affects."

SPA-2-VOLT_CRITICAL

2-Critical

[chars] voltage outside of nominal range. Nominal [dec]mV value[dec]mV

MSG_SPA_VOLT_EXP_COMMON

-

MSG_SPA_VOLT_ACTION_SCHED_REPLACE

SPA-2-VOLT_SHUTDOWN_OVR

2-Critical

[chars] voltage outside of operating range. Nominal [dec]mV value[dec]mV.

MSG_SPA_VOLT_EXP_COMMON

-

MSG_SPA_VOLT_SCHED_REPLACE

SPA-0-VOLT_SHUTDOWN

0-Emergency

[chars] voltage out of operating range. Nominal [dec]mV value [dec]mV.

MSG_SPA_VOLT_EXP_COMMON The SPA has been shut down to prevent component damage.

-

"Replace the SPA immediately. " "Record the associated messages and return the SPA for service."

SPA_OIR-3-MESSAGE_ERROR

3-Error

[chars]: SPA OIR event message error - [chars][dec]

An error was detected in a SPA OIR event message for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-UNEXPECTED_EVENT

3-Error

[chars]: SPA OIR unexpected event[dec]

An unexpected SPA OIR event was detected for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-INVALID_EVENT

3-Error

[chars]: Invalid [chars] event received when SPA is undergoing Minimal Disruptive Restart

An unexpected event was detected when the SPA was was undergoing Minimal Disruptive Restart. This condition is most likely a software problem. The SPA will be reset as normal and this will impact traffic.

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-EVENT_DATA_ERROR

3-Error

SPA OIR event data error - [chars][dec]

Invalid data was detected within a SPA OIR event. The SPA OIR state machines may not reflect the state of the hardware. The problem only affects one SPA but the SPA cannot be determined from the context where the error was detected. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

"Check the system log for other messages that may help determine " "which SPA is affected. " SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-POST_EVENT_ERROR

3-Error

[chars]: event [dec]

A SPA OIR event message was not enqueued for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition is most likely due to a software problem.

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-UNEXPECTED_RECOVERY_ACTION

3-Error

[chars]: SPA [chars] unexpected recovery action[dec] for fail code 0x[hec]

An error occured while processing a failure message for the SPA in the slot or subslot number specified in the error message. The recovery action to be taken after a SPA failure is determined by calling a SPA driver function. This message indicates that the SPA driver function returned an invalid recovery action. After this message was issued the SPA was reloaded in an attempt to recover. The SPA driver most likely returned an invalid recovery action because of a software problem.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-EVENT_HANDLING

3-Error

[chars]: [chars]0x[hec]

A data structure error was detected when handling a SPA OIR event for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware. This condition is most likely due to a software problem.

spa-infra

SPA_OIR_STD_ACTION

SPA_OIR-3-CMD_ATTR

3-Error

[chars]: Unexpected command identifier [dec]

An unexpected command identifier was detected when processing command related to a SPA OIR. The command was not processed. This is most likely due to a software problem.

spa-infra

SPA_OIR_STD_ACTION

SPA_OIR-2-INITFAIL

2-Critical

SPA OIR initialization error

A failure occurred during the SPA OIR subsystem startup. SPA OIR is not functional for the RP or line card that generated the message.

-

LOG_STD_REDUCE_ACTION

SPA_OIR-2-SUBSLOTINITFAIL

2-Critical

SPA OIR initialization error for [chars]

A failure occurred during the SPA OIR subsystem startup. SPA OIR is not functional for the slot or subslot specified in the error message

-

LOG_STD_REDUCE_ACTION

SPA_OIR-3-EVENT_TIMEOUT

3-Error

[chars]: Timeout waiting for SPA OIR event

A timeout occurred for the subslot specified in the error message while waiting for a SPA OIR event. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR event are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-SW_INIT_TIMEOUT

3-Error

[chars]: SPA initialization not completed

A timeout occurred for the subslot specified in the error message while waiting for SPA software driver to initialize the SPA. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by software firmware or hardware problem but a software or firmware problem is more likely.

-

"Check for other messages reported for futher insight. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco techinical support representative. " SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-HW_INIT_TIMEOUT

3-Error

[chars]

A timeout occurred for the subslot specified in the error message while waiting for SPA hardware to initialize. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by a software firmware or hardware problem but a firmware or hardware problem is more likely.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-OUT_OF_SYNC

3-Error

[chars]: failure code 0x[hec]

The software SPA OIR state did not match the hardware state for the subslot in the error message. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition is expected if a SPA is reloading when an RP switchover occurs. Otherwise this condition could be caused by a software firmware or hardware problem but a firmware or software problem is more likely. This condition could also be caused by a rare interaction between SPA and its SIP.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-HW_SIGNAL_DEASSERTED

3-Error

[chars]

The SPA was not brought up because the SPA bay is in an admin down state. The SPA bay will appear as <CmdBold>hw-module<NoCmdBold> <target spa> <CmdBold>shutdown<NoCmdBold> in the running configuration.

-

"Use the <CmdBold>no hw-module<NoCmdBold> <target spa> " "<CmdBold>shutdown<NoCmdBold> command to administratively enable " "the SPA bay."

SPA_OIR-6-PRECONFIG_MISMATCH

6-Information

[chars]: Inserted SPA type does not match preconfigured SPA type. Configuration updated

This message reports a mismatch between the inserted SPA type and the preconfigured SPA type on platforms that support pre-configuration. The inserted SPA replaces the preconfigured SPA.

-

"Check the configuration with the <CmdBold>show run<NoCmdBold> command. " "If you would like to revert to the preconfigured type remove the SPA " "and then update the configuration from a backup"

SPA_OIR-3-SPA_POWERED_OFF

3-Error

[chars]: SPA [chars] powered off after [dec] failures within [dec] seconds

The SPA was powered off because it failed too often. This condition may be caused by a software firmware or hardware error.

-

"Look for other error messages related to this SPA subslot to " "determine root cause of the failure. " SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-CORRUPT_EVENT

3-Error

[chars]

Corruption was detected within a SPA OIR event for the subslot specified in the error message. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by a software firmware or hardware problem but a firmware or software problem is more likely. For distributed platforms SPA OIR events are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-UNRECOGNIZED

3-Error

The SPA of type 0x%X in [chars] is not recognized

The type of the SPA in the specified subslot is not recognized by the operating system. The operating system might not support this SPA type on this platform or the SPA type identification stored on the SPA is invalid.

-

"Ensure that the system is running a version of the operating " "system that supports the SPA type specified in the error " "message on this platform. If the correct operating system " "version is in use copy the error message exactly as it " "appears on the console or in the system log contact your " "Cisco technical support representative and provide the " "representative with the gathered information. Include the " "information about the SPA type found on the front of the " "SPA."

SPA_OIR-3-UNSUPPORTED

3-Error

The [chars] in [chars] is not supported by the [chars] module

The SPA in the subslot specified in the error message is not supported in the specified SIP by the version of the operating system currently running on the system. The SPA type may be supported by another SIP or by a later operating system release.

-

"Ensure that the SIP specified in the error " "message supports the specified SPA type. Ensure that the " "operating system release supports the SPA type in the SIP. " "It may be necessary to upgrade your system to " "the latest operating system release in your release train or " "it may be necessary to use a different SIP type. If " "the SPA type specified in the error message does not match the " "interface types or numbers shown on the front of the SPA copy " "the error message exactly as it appears on the console or in " "the system log contact your Cisco technical support " "representative and provide the representative with the " "gathered information. Include information regarding the SPA " "type found on the front of the SPA."

SPA_OIR-3-RECOVERY_RELOAD

3-Error

[chars]: Attempting recovery by reloading SPA

The OIR facility attempted automatic recovery by reloading the SPA in the subslot specified in the error message. Look for other error messages related to this SPA subslot to determine the failure that triggered the automatic recovery.

-

LOG_STD_NO_ACTION

SPA_OIR-6-REMCARD

6-Information

Card removed from [chars] interfaces disabled

The OIR facility detected the removal of a SPA from the slot or subslot number specified in the error message. The interfaces on that SPA will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces.

-

LOG_STD_NO_ACTION

SPA_OIR-6-INSCARD

6-Information

Card inserted in [chars]

The OIR facility detected a newly inserted SPA. The interfaces associated with that SPA are operational but will be shut down until they are configured by the user. If any interfaces of that type were previously configured they will be restored to their previous state.

-

LOG_STD_NO_ACTION

SPA_OIR-6-ONLINECARD

6-Information

SPA [chars] online in [chars]

The OIR facility detected the state change to online for the SPA in the slot or subslot number specified in the message.

-

LOG_STD_NO_ACTION

SPA_OIR-6-OFFLINECARD

6-Information

SPA [chars] offline in [chars]

The OIR facility detected the state change to offline for the SPA in the slot or subslot number specified in the message.

-

LOG_STD_NO_ACTION

SPA_EEPROM-4-DATA_TRUNCATED

4-Warning

[chars]: Data will be truncated for field type 0x[hec] - size [dec] bytes too

The provided data to be written into the indicated field type of SPA EEPROM is too big and the data will be truncated in order to fit into the allowed space.

spa-infra

"Retry the operation again with a data size that will fit into the " "indicated size for the field type."

SPA_EEPROM-4-CANNOT_UPDATE

4-Warning

[chars]: EEPROM data cannot be updated at this moment because the SPA is not in service.

The EEPROM update operation cannot be performed because the indicated SPA could have been in \out of service\ state \admin down\ state or is trying to get initialized.

spa-infra

"Retry the operation when the SPA is in service. The operational status " "of the SPA can be checked with the <CmdBold>show hw-module subslot" "<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg> <CmdBold>oir<NoCmdBold> " "command. If the SPA is shown in \"out of service\" state correct the " "indicated problem before the retry to update EEPROM. If the state shown " "is in \"admin down\" re-enable the SPA with <CmdBold>no hw-module " "subslot<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg> <CmdBold>shutdown" "<NoCmdBold> command."

SPA_EEPROM-3-RPC_FAILED

3-Error

Failed to send RPC message to [chars] EEPROM of [chars] in [chars] - [chars]

System failed to send a RPC message to read/write the EEPROM of the indicated SPA. The cause of the error condition is shown in the error message.

-

SPA_EEPROM_STD_RESOURCE_ACTION

SPA_EEPROM-3-READ_FAILED

3-Error

Failed to read the EEPROM content of [chars] in [chars] offset=0x[hec] num_byte=[dec]

System failed to read the EEPROM content of the indicated SPA with the specified offset value and number of bytes to read.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-WRITE_FAILED

3-Error

Failed to write the EEPROM content for [chars] in [chars] offset=0x[hec] num_byte=[dec]

System failed to write data into the EEPROM of the indicated SPA with the specified offset value and number of bytes to write.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-SET_WR_PROTECT_FAILED

3-Error

[chars]: Failed to [chars] the EEPROM write protect mode on [chars].

System failed to enable/disable the write protect mode for SPA EEPROM on the indicated device. This might happen if the device were busy performing other tasks.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-FIELD_NOT_FOUND

3-Error

[chars]: Failed to find content of field type 0x[hec] with data size = [dec] bytes. The EEPROM might require an update.

System failed to find the content of the indicated field type from the SPA EEPROM. The format of the EEPROM of the indicated SPA might not be up to date.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-FORMAT_ERROR

3-Error

[chars]: [chars]. The EEPROM might require an update.

A format error has been detected in the EEPROM of the indicated SPA. The type of error is indicated in the error message.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-SW_ERROR

3-Error

NULL

-

spa-infra

LOG_STD_ACTION

DUAL-3-SIA

3-Error

Route [chars] stuck-in-active state in [chars] [dec]. Cleaning up

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOMATCH

3-Error

Nexthop and infosource don't match. N = [chars] I = [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOHANDLE

3-Error

Handle [dec] is not allocated in pool.

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-LINKSTILLUP

3-Error

Link [dec] [chars] still exists on [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-LINKSEXIST

3-Error

Interface [chars] going down and [dec] links exist

-

-

LOG_STD_ACTION

DUAL-3-BADCOUNT

3-Error

Route [chars] [dec] successors [dec] rdbs

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-6-EVENT

6-Information

[chars] [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOSOCKET

3-Error

Unable to open socket for AS [dec]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOBUFFER

3-Error

No buffers available for [dec] byte packet

The DUAL software was unable to allocate a packet buffer. The system\n\ may be out of memory.

-

LOG_STD_SH_TECH_ACTION

DUAL-3-UNKTIMER

3-Error

Unknown timer type [dec] expiration

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-REFCOUNT

3-Error

Negative refcount in pakdesc [hec]

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-3-MULTIFLOW

3-Error

Flow control error [chars] on [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-PEERSEXIST

3-Error

[dec] peers exist on IIDB [chars]

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-3-ANCHORCOUNT

3-Error

Anchor count negative

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-5-NBRCHANGE

5-Notice

[chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars]

A neighbor went up or down.

-

LOG_STD_NO_ACTION

DUAL-6-NBRINFO

6-Information

[chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars]

Information regarding a neighbor.

-

LOG_STD_NO_ACTION

DUAL-3-RDBLEFT

3-Error

Lingering DRDB deleting IIDB dest [chars] nexthop [chars] [chars] origin [chars]

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-3-INTERNAL

3-Error

[chars] [dec]: Internal Error

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-4-PFXLIMITTHR

4-Warning

[chars] [dec]: [chars] threshold prefix level[dec] reached.

-

-

-

DUAL-3-PFXLIMIT

3-Error

[chars] [dec]: [chars] prefix limit reached[dec].

Number of prefixes for eigrp has reached the configured or default limit.

-

"Use \"show ip eigrp accounting\" for details " "on the source of the prefixes and take corrective " "measures."

DUAL-3-BADIGRPSAP

3-Error

Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help

An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch.

novell

"Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative."

DUAL-3-BADIGRPSAPTYPE

3-Error

Unsupported SAP type for EIGRP being [chars] - type [hec]

-

novell

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the <bold>debug ipx sap activity<nobold> and <bold>debug ipx sap event<nobold> commands for the\n\ period during which this message appeared."

DUAL-3-SIA

3-Error

Route [chars] stuck-in-active state in [chars] [dec]. Cleaning up

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOMATCH

3-Error

Nexthop and infosource don't match. N = [chars] I = [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOHANDLE

3-Error

Handle [dec] is not allocated in pool.

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-LINKSTILLUP

3-Error

Link [dec] [chars] still exists on [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-LINKSEXIST

3-Error

Interface [chars] going down and [dec] links exist

-

-

LOG_STD_ACTION

DUAL-3-BADCOUNT

3-Error

Route [chars] [dec] successors [dec] rdbs

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-6-EVENT

6-Information

[chars] [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOSOCKET

3-Error

Unable to open socket for AS [dec]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-NOBUFFER

3-Error

No buffers available for [dec] byte packet

The DUAL software was unable to allocate a packet buffer. The system\n\ may be out of memory.

-

LOG_STD_SH_TECH_ACTION

DUAL-3-UNKTIMER

3-Error

Unknown timer type [dec] expiration

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-REFCOUNT

3-Error

Negative refcount in pakdesc [hec]

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-3-MULTIFLOW

3-Error

Flow control error [chars] on [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

DUAL-3-PEERSEXIST

3-Error

[dec] peers exist on IIDB [chars]

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-3-ANCHORCOUNT

3-Error

Anchor count negative

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-5-NBRCHANGE

5-Notice

[chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars]

A neighbor went up or down.

-

LOG_STD_NO_ACTION

DUAL-6-NBRINFO

6-Information

[chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars]

Information regarding a neighbor.

-

LOG_STD_NO_ACTION

DUAL-3-RDBLEFT

3-Error

Lingering DRDB deleting IIDB dest [chars] nexthop [chars] [chars] origin [chars]

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-3-INTERNAL

3-Error

[chars] [dec]: Internal Error

A software or hardware error occurred.

-

LOG_STD_ACTION

DUAL-4-PFXLIMITTHR

4-Warning

[chars] [dec]: [chars] threshold prefix level[dec] reached.

-

-

-

DUAL-3-PFXLIMIT

3-Error

[chars] [dec]: [chars] prefix limit reached[dec].

Number of prefixes for eigrp has reached the configured or default limit.

-

"Use \"show ip eigrp accounting\" for details " "on the source of the prefixes and take corrective " "measures."

DUAL-3-BADIGRPSAP

3-Error

Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help

An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch.

novell

"Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative."

DUAL-3-BADIGRPSAPTYPE

3-Error

Unsupported SAP type for EIGRP being [chars] - type [hec]

-

novell

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the <bold>debug ipx sap activity<nobold> and <bold>debug ipx sap event<nobold> commands for the\n\ period during which this message appeared."

LLIST-3-ONLIST

3-Error

[chars] to 0x[hec] 0x[hec] on list

An internal inconsistency was detected when an attempt was made to\n\ add an item to a list already on the list.

tag-switch

"Copy the message exactly as it appears and report it to your technical\n\ service representative."

LLIST-3-OFFLIST

3-Error

[chars] from 0x[hec] 0x[hec] not on list

TXTHREAD API returned a perror.

tag-switch

"Copy the message exactly as it appears and report it to your technical\n\ service representative."

MPLS_TE_HA-3-PROCESS_CREATE_FAILED

3-Error

Failed to create RSVP HA process

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process"

MPLS_TE_HA-3-PROCESS_KILL

3-Error

Killing RSVP HA process

system may be low on memory. Failed to create RSVP HA \n services

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_HA-3-CF_REGISTER_FAILED

3-Error

Failed to register with CF

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-RF_REGISTER_FAILED

3-Error

Failed to register with RF

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-RF_UNREGISTER_FAILED

3-Error

Failed to unregister with RF

RSVP HA client may not have registered with RF

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_HA-3-CLI_ADD_FAILED

3-Error

Failed to add RSVP HA to CLI

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-DB_INIT_FAILED

3-Error

Database init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-MSG_MGR_INIT_FAILED

3-Error

Message Manager init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-ISSU_INIT_FAILED

3-Error

In Service Software Upgrade ISSU Init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-MAIN_INIT_FAILED

3-Error

Main init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-ENTRY_MOVE_FAILED

3-Error

Failed to move a database entry to [chars] tree

An attempt to move a data entry from one wavl tree to another wavl tree failed

mpls-te

"This error should never happen under normal " "operation and indicates an internal error. " "Open a ddts"

MPLS_TE_HA-3-ITEM_SIZE_TOO_BIG

3-Error

Item size [dec] bigger than default CF buffer [dec] supported by

A database entry cannot be sent to the standby because the database entry doesn't fit in a CF maximum size buffer allowed by the platform.

mpls-te

"This error indicates a problem with design in " "handling platform dependent restrictions. " "Open a ddts"

MPLS_TE_HA-3-SSO_UNSUPPORTED

3-Error

Attempt to init RSVP HA subsystem when TE SSO not supported

RSVP TE SSO is included in image that doesn't support SSO

mpls-te

"This error indicates a problem with design in. " "Open a ddts"

MPLS_TE_NSR-3-RESEQUENCE_ERROR

3-Error

Error occurred during TE NSR resequence

An unrecoverable error occurred during TE NSR resequence of state

mpls-te

"Disable and then reenable TE NSR functionality and " "open a DDTS"

TENSRFSM-3-NULLMACH

3-Error

Invalid machine pointer 0x%X

state machine invalid pointer

mpls-te

LOG_STD_ACTION

TENSRFSM-3-INVSTATE

3-Error

Invalid current state 0x%X

state machine invalid state

mpls-te

LOG_STD_ACTION

TENSRFSM-3-INVEVENT

3-Error

Invalid event_id 0x%X

state machine invalid event

mpls-te

LOG_STD_ACTION

TENSRFSM-3-INVTRANS

3-Error

obj: [0x%08X] event_id: [0x%08X] er_p: [0x%08X] arg: [0x%08X] session state [chars] -> [chars]

state machine invalid transition

mpls-te

LOG_STD_ACTION

TENSRFSM-3-NOEVENT

3-Error

Unable to apply event 0x%08X

state machine transition failure

mpls-te

LOG_STD_ACTION

TENSRFSM-3-NOPROCID

3-Error

Unable to launch TE NSR FSM Process.

state machine transition process launch failure

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-3-INIT

3-Error

[chars]

An internal inconsistency was detected during MPLS TE path calculation initialization such as an attempt was made to initialize the MPLS TE path calculation system id before the system_id size is known.

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-3-PATH

3-Error

[chars]

An internal inconsistency was detected when an attempt was made to establish an MPLS TE tunnel using the MPLS TE path calculation subsystem.

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-3-LSA

3-Error

[chars] [chars]

An internal inconsistency was detected when an attempt was made to establish handle received lsa for MPLS TE topology database.

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-2-MEM

2-Critical

[chars] [dec]

A failure at an attempt to alloc memory was detected

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-2-DUP_RRR_ID

2-Critical

[chars] [chars] [chars]

Two nodes have the same stable router id

mpls-te

"Find the system that has the duplicate router id and configure a " "different one"

MPLS_TE_PCALC-2-INVLD_RTR_ID

2-Critical

Invalid router id [chars] received from [chars] in fragment %lu

Received an Invalid Router LSA. LSA should not contain a Router id of zero. The cause of this problem may be misconfiguration memory corruption or unexpected behaviour on a router

mpls-te

"Locate the problem router and check the configuration. " "To determine what is causing this problem call " "your Cisco technical support representative for assistance."

MPLS_TE_PCALC-2-INVLD_RTR_FRAGMENT

2-Critical

Router id [chars] received from [chars] in fragment %lu

Received Router ID in multiple fragments

mpls-te

"Locate the problem router and contact your Cisco " "technical support representative for assistance."

MPLS_TE_PCALC-2-DUP_IP_ADDRESS

2-Critical

[chars] [chars] [chars]

Two nodes have the same stable ip address

mpls-te

"Find the system that has the duplicate ip address and configure a " "different one"

MPLS_TE_LM-5-CLEAR_COUNTERS

5-Notice

Clear MPLS TE Link Management counters by [chars]

The MPLS TE Link Management counters have been cleared

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_LM-3-CONSISTENCY

3-Error

[chars]: [chars] [chars] [chars]

An action attempted by the MPLS TE Link Management implementation encountered an unexpected condition

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE_LM-3-LSP_BAD_SWITCHING_TYPE_REQUESTED

3-Error

[chars]: LSP requests switching type [[chars]] unsupported on link [[chars]]

-

-

-

MPLS_TE_LM-3-LSP_BAD_GPID_REQUESTED

3-Error

[chars]: LSP requests G-PID unsupported or invalid

-

-

-

MPLS_TE_LM-3-LSP_BAD_ENCODING_TYPE_REQUESTED

3-Error

[chars]: LSP requests encoding type unsupported or invalid

The indicated TE LSP routed on the indicated interface requested a Switching Type that is unsupported on the interface. The requested value appears in the Generalized Label Request.

mpls-te

"Verify that the head end originating the TE LSP has a Generalized " "Label Request that is specifying a Switching Type acceptable to the " "interface in question. If not alter the head end configuration " "to request an LSP with an appropriate value or cause the LSP " "to be routed on a different interface. " "If this problem still persists copy the error message exactly as " "it appears on the console or in the system log. Please perform " "a search of the Bug Toolkit " BUG_TOOLKIT ". If you need additional " "assistance open a case with the Technical Assistance Center via " "the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Please provide the output of " "<cmdBold>show tech-support<nocmdBold> and a topology diagram " "showing the hops in the LSP marking each hop with the " "vendor/software and identify which hop is the IOS device issuing " "the error message."

MPLS_TE_LM-3-LSP_BAD_ENCODING_TYPE

3-Error

LSP [chars] requesting Encoding Type [[chars]] that is unsupported on interface [chars].

The indicated TE LSP routed on the indicated interface requested an Encoding Type that is unsupported on the interface. The requested value appears in the Generalized Label Request.

mpls-te

"Verify that the head end originating the TE LSP has a Generalized " "Label Request that is specifying an Encoding Type acceptable to the " "interface in question. If not alter the head end configuration " "to request an LSP with an appropriate value or cause the LSP " "to be routed on a different interface. " "If this problem still persists copy the error message exactly as " "it appears on the console or in the system log. Please perform " "a search of the Bug Toolkit " BUG_TOOLKIT ". If you need additional " "assistance open a case with the Technical Assistance Center via " "the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Please provide the output of " "<cmdBold>show tech-support<nocmdBold> and a topology diagram " "showing the hops in the LSP marking each hop with the " "vendor/software and identify which hop is the IOS device issuing " "the error message."

MPLS_TE_LM-3-LSP_BAD_SWITCHING_TYPE

3-Error

LSP [chars] requesting Switching Type [[chars]] that is unsupported on interface [chars].

The indicated TE LSP routed on the indicated interface requested a Switching Type that is unsupported on the interface. The requested value appears in the Generalized Label Request.

mpls-te

"Verify that the head end originating the TE LSP has a Generalized " "Label Request that is specifying a Switching Type acceptable to the " "interface in question. If not alter the head end configuration " "to request an LSP with an appropriate value or cause the LSP " "to be routed on a different interface. " "If this problem still persists copy the error message exactly as " "it appears on the console or in the system log. Please perform " "a search of the Bug Toolkit " BUG_TOOLKIT ". If you need additional " "assistance open a case with the Technical Assistance Center via " "the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Please provide the output of " "<cmdBold>show tech-support<nocmdBold> and a topology diagram " "showing the hops in the LSP marking each hop with the " "vendor/software and identify which hop is the IOS device issuing " "the error message."

MPLS_TE_LM-3-LSP_BAD_GPID

3-Error

LSP [chars] requesting G-PID [[chars]] that is unsupported on interface [chars][chars].

The indicated TE LSP routed on the indicated interface requested a Generalized Payload Identifier unsupported on the

mpls-te

"Verify that the head end originating the TE LSP has a " "Label Request that is specifying a PID acceptable to the " "interface in question. If not one possibility is to alter the " "head end configuration to request an LSP with an appropriate value. " "Alternatively if this error is generated at the penultimate hop of " "an LSP where the endpoint is advertising an implicit-null label " "penultimate hop popping is in use alter the endpoint to "

MPLS_TE_LM-3-GMPLS_UNSUPPORTED_RESOURCE

3-Error

Interface [chars]: GMPLS [chars] labels unsupported

The indicated interface is unable to provide labels of the indicated type.

mpls-te

LOG_STD_SH_TECH_ACTION

MPLS_TE_LM-3-INVALID_LSP

3-Error

A valid LSP must be present for [chars]

A valid LSP is required for this action. This is not a typical occurrence.

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_AUTOMESH-5-AUTOTEMPLATE_HWIDB_DELETE

5-Notice

Failed to delete hwidb for Auto-Template [dec] index [dec]

Deletion of Auto-Template interface failed.

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-3-LOCK_DOUBLE

3-Error

Unexpected data structure access. Non-zero lock count [dec] when [chars] locks [dec] failure[chars].

MPLS_TE_AUTO_TUN_STD_LOCK_EXPLANATION

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-3-LOCK_ZERO

3-Error

Unexpected data structure access. [chars] unlocks with count [dec] but not locked [dec] failure[chars].

MPLS_TE_AUTO_TUN_STD_LOCK_EXPLANATION

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-3-LOCK_COUNT

3-Error

Unexpected data structure access. [chars] unlocks with count [dec] but expected [dec] [dec] failure[chars].

MPLS_TE_AUTO_TUN_STD_LOCK_EXPLANATION

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-4-REMOVE_FAIL

4-Warning

Removing existing auto tunnels may have failed.[chars][chars] MPLS_TE_AUTO_TUN_STD_CONFIRM Use \show running-config\ to confirm expected configuration. Repeat CLI configuration as needed.

The MPLS Traffic Engineering Auto-Tunnel software detected a possible \ problem removing existing automatic tunnels. It may be necessary to \ repeat the CLI action that caused the removal and reconfiguration of \ automatic tunnels.

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-4-CONFLICT_CFG

4-Warning

[chars]

Conflicting MPLS TE auto-tunnel configuration

mpls-te

"Re-check auto-tunnel configuration for P2P Primary Backup and Mesh" "make sure tunnel-id range are not overlapped."

MPLS_TE-3-SIGNALLERINIT

3-Error

Signaller unable to [chars]register RSVP [chars]

A message handler used by the signaller to receive events or requests from RSVP could not be installed or removed.

mpls-te

"Copy and save the message. If possible re-start " "the TSP tunnel signalling process by issuing the " "no tag-switching tsp-tunnels command followed by " "the tag-switching tsp-tunnels command. If the " "message continues to occur even after re-starting " "the signalling process several times then contact " "your technical support representative for " "assistance."

MPLS_TE-3-TUNNELKILL

3-Error

Tunnel removal attempt by [chars] failed for tunnel [chars]: [chars]

-

-

-

MPLS_TE-3-CONSISTENCY

3-Error

[chars]: [chars] [chars] [chars]

An action attempted by the traffic engineering tunnel implementation encountered an unexpected condition

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-4-LSPREJECT

4-Warning

LSP [chars] rejected: matching passive TE tunnel [chars]

An RSVP Path message for an LSP for a tunnel was rejected with a PathErr message due to the absence of a properly configured MPLS passive tunnel interface which is administratively up.

mpls-te

"Create and/or properly configure an MPLS passive tunnel interface " "which will match the rejected LSP and ensure that it is " "administratively up or modify the tunnel interface configuration " "at the head end of the tunnel."

MPLS_TE-5-LSP

5-Notice

[chars]

An informational traffic engineering tunnel trap was generated for an LSP event.

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-5-TUN

5-Notice

[chars]

An informational traffic engineering tunnel trap was generated for a Tunnel event.

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-5-FRR

5-Notice

[chars]

An informational traffic engineering tunnel trap was generated for an MPLS Fast-Reroute event.

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-3-PHYSINTFCDOWN

3-Error

[chars]'s LSP interface [chars] did not come up after [dec] msecs

The underlying interface for a tunnel LSP did not come up although the tunnel itself is up.

mpls-te

"See if the underlying interface is physically connected."

MPLS_TE-3-MFIERROR

3-Error

[chars]: [chars] [chars]

A traffic engineering request to the label switching database encountered an unexpected condition

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-2-BUNDLE_INSERT

2-Critical

[chars] [chars]

Request for inserting a traffic engineering tunnel bundle failed.

mpls-te

LOG_STD_ACTION

MPLS_TE-2-UNSUPPORTED_LINK_TYPE

2-Critical

[chars]

Unsupported link type

mpls-te

LOG_STD_ACTION

MPLS_TE-2-ADJ_WALK_ERR

2-Critical

[chars]

Error during bundle adjacency walk

mpls-te

LOG_STD_ACTION

MPLS_TE-4-CONFLICT_BIDIR_CFG

4-Warning

[chars]

Conflicting bidirectional association configuration

mpls-te

"Re-check tunnel configuration and make sure destination of tunnel" "is properly set and the bidirectional association is unique against" "all tunnels."

MPLS_TE-4-PCEP_REPORT_FAILED

4-Warning

LSP TID:[dec] LID:[dec] wasn't reported to the PCE server

-

-

-

MPLS_TE-4-PCEP_REQUEST_FAILED

4-Warning

Unable to request path for LSP TID:[dec] LID:[dec] from PCE server

-

-

-

PROCESS_CREATE_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

PROCESS_KILL-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

CF_REGISTER_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

RF_REGISTER_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

RF_UNREGISTER_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

CLI_ADD_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

DB_INIT_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

MSG_MGR_INIT_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

ISSU_INIT_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

MAIN_INIT_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

ENTRY_MOVE_FAILED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

ITEM_SIZE_TOO_BIG-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

STATE_FAILURE-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

SSO_UNSUPPORTED-3-MPLS_TE_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

NULLMACH-3-TENSRFSM

3-Error

ERRMSG_NOFLAGS

-

-

-

INVSTATE-3-TENSRFSM

3-Error

ERRMSG_NOFLAGS

-

-

-

INVEVENT-3-TENSRFSM

3-Error

ERRMSG_NOFLAGS

-

-

-

INVTRANS-3-TENSRFSM

3-Error

ERRMSG_NOFLAGS

-

-

-

NOEVENT-3-TENSRFSM

3-Error

ERRMSG_NOFLAGS

-

-

-

NOPROCID-3-TENSRFSM

3-Error

ERRMSG_NOFLAGS

-

-

-

INIT-3-MPLS_TE_PCALC

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

PATH-3-MPLS_TE_PCALC

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

LSA-3-MPLS_TE_PCALC

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

MEM-2-MPLS_TE_PCALC

2-Critical

ERRMSG_FLAG_TRACEBACK

-

-

-

DUP_RRR_ID-2-MPLS_TE_PCALC

2-Critical

ERRMSG_FLAG_TRACEBACK

-

-

-

INVLD_RTR_ID-2-MPLS_TE_PCALC

2-Critical

ERRMSG_NOFLAGS

-

-

-

INVLD_RTR_FRAGMENT-2-MPLS_TE_PCALC

2-Critical

ERRMSG_NOFLAGS

-

-

-

DUP_IP_ADDRESS-2-MPLS_TE_PCALC

2-Critical

ERRMSG_FLAG_TRACEBACK

-

-

-

CLEAR_COUNTERS-5-MPLS_TE_LM

5-Notice

ERRMSG_NOFLAGS

-

-

-

CONSISTENCY-3-MPLS_TE_LM

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

LSP_BAD_SWITCHING_TYPE_REQUESTED-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

LSP_BAD_GPID_REQUESTED-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

LSP_BAD_ENCODING_TYPE_REQUESTED-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

LSP_BAD_ENCODING_TYPE-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

LSP_BAD_SWITCHING_TYPE-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

LSP_BAD_GPID-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

GMPLS_UNSUPPORTED_RESOURCE-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

INVALID_LSP-3-MPLS_TE_LM

3-Error

ERRMSG_NOFLAGS

-

-

-

AUTOTEMPLATE_HWIDB_DELETE-5-MPLS_TE_AUTOMESH

5-Notice

ERRMSG_FLAG_TRACEBACK

-

-

-

LOCK_DOUBLE-3-MPLS_TE_AUTO_TUN

3-Error

ERRMSG_NOFLAGS

-

-

-

LOCK_ZERO-3-MPLS_TE_AUTO_TUN

3-Error

ERRMSG_NOFLAGS

-

-

-

LOCK_COUNT-3-MPLS_TE_AUTO_TUN

3-Error

ERRMSG_NOFLAGS

-

-

-

REMOVE_FAIL-4-MPLS_TE_AUTO_TUN

4-Warning

ERRMSG_NOFLAGS

-

-

-

NOMEM-2-MPLS_TE_EXT_FWDG

2-Critical

ERRMSG_NOFLAGS

-

-

-

REG_FAIL-2-MPLS_TE_EXT_FWDG

2-Critical

ERRMSG_NOFLAGS

-

-

-

DEREG_FAIL-3-MPLS_TE_EXT_FWDG

3-Error

ERRMSG_NOFLAGS

-

-

-

CBERR-3-MPLS_TE_EXT_FWDG

3-Error

ERRMSG_NOFLAGS

-

-

-

GENERIC-3-MPLS_TE_EXT_FWDG

3-Error

ERRMSG_NOFLAGS

-

-

-

UNKNOWN_EVENT-3-MPLS_TE_EXT_FWDG

3-Error

ERRMSG_NOFLAGS

-

-

-

BATCH_ERR-3-MPLS_TE_EXT_FWDG

3-Error

ERRMSG_NOFLAGS

-

-

-

IF_FAIL-2-MPLS_TE_EXT_FWDG

2-Critical

ERRMSG_NOFLAGS

-

-

-

BIND_FAIL-2-MPLS_TE_EXT_FWDG

2-Critical

ERRMSG_NOFLAGS

-

-

-

UNEXPECTEDEVENT-3-MPLS_TE_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

UNEXPECTEDQUEUE-3-MPLS_TE_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

UNEXPECTEDTIMER-3-MPLS_TE_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

UNEXPECTEDMESSAGE-3-MPLS_TE_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

NOMEMORY-2-MPLS_TE_SYS

2-Critical

ERRMSG_NOFLAGS

-

-

-

SIGNALLERINIT-3-MPLS_TE

3-Error

ERRMSG_NOFLAGS

-

-

-

TUNNELKILL-3-MPLS_TE

3-Error

ERRMSG_NOFLAGS

-

-

-

CONSISTENCY-3-MPLS_TE

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

LSPREJECT-4-MPLS_TE

4-Warning

ERRMSG_NOFLAGS

-

-

-

LSP-5-MPLS_TE

5-Notice

ERRMSG_NOFLAGS

-

-

-

TUN-5-MPLS_TE

5-Notice

ERRMSG_NOFLAGS

-

-

-

FRR-5-MPLS_TE

5-Notice

ERRMSG_NOFLAGS

-

-

-

PHYSINTFCDOWN-3-MPLS_TE

3-Error

ERRMSG_NOFLAGS

-

-

-

MFIERROR-3-MPLS_TE

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

BUNDLE_INSERT-2-MPLS_TE

2-Critical

ERRMSG_FLAG_TRACEBACK

-

-

-

UNSUPPORTED_LINK_TYPE-2-MPLS_TE

2-Critical

ERRMSG_FLAG_TRACEBACK

-

-

-

ADJ_WALK_ERR-2-MPLS_TE

2-Critical

ERRMSG_FLAG_TRACEBACK

-

-

-

MPLS_TP_MEM-3- NO_MEM

3-Error

Could not allocate memory for MPLS-TP context

Could not allocate memory for MPLS-TP context. This is an internal issue to MPLS-TP

mpls-tp

LOG_STD_ACTION

MPLS_TP_PROC-3- PROC_CREATE_FAIL

3-Error

[chars] [chars] [dec]

Could not create MPLS-TP process. This is an internal issue to MPLS-TP

mpls-tp

LOG_STD_ACTION

MPLS_TP_PROC-3- UNKNOWN_MESSAGE

3-Error

Received unknwon message:[dec]

An unknown message was posted to the MPLS-TP process. This is an internal issue to MPLS-TP

mpls-tp

LOG_STD_ACTION

MPLS_TP_PROC-3- UNKNOWN_EVENT

3-Error

Received unknown event: Major:[dec] Minor:[dec]

An unknown event was posted to the MPLS-TP queue. This is an internal issue to MPLS-TP.

mpls-tp

LOG_STD_ACTION

MPLS_TP_TIMER-3- UNKNOWN_TIMER_TYPE_EXPIRY

3-Error

Unknown timer type expired:[dec]

An unknown MPLS-TP timer type expired. This is an issue internal to MPLS-TP

mpls-tp

LOG_STD_ACTION

MPLS_TP_LSP_FSM-3- LSP_FSM_ERROR

3-Error

LSP FSM Error occurred. Received event:[chars] in state:[chars]

An erroneous event was received by the TP LSP. This is an error internal to MPLS-TP

mpls-tp

LOG_STD_ACTION

MPLS_TP-3-UPDOWN

3-Error

Tunnel-tp[dec] changed state to [chars]

The MPLS-TP tunnel-tp interface changed state.

-

"If the state change was unexpected confirm the configuration settings " "and those of other LSRs along the tunnel LSPs."

MPLS_TP-5-REDUNDANCY

5-Notice

Tunnel-tp[dec] switched to [chars] LSP as active

The MPLS-TP tunnel-tp interface has changed the LSP over which it data traffic is carried possibly due to a fault or administrative action or to restore traffic to the working-LSP after LSP recovery.

-

"If this change is unexpected examine LSP messages to determine " "if a fault or other failure has occurred or is this is due to " "a lockout condition or configuration change."

MPLS_TP-5-CONFIG_CHANGED

5-Notice

Tunnel-tp[dec] is [chars]

The configuration of the tunnel-tp interface has changed. This message is to notify the NMS of changes.

-

LOG_STD_ACTION

MPLS_TP-5-PSCPREEMPTION

5-Notice

Tunnel-tp[dec] PSC Event: [chars] preempted PSC State: [chars] new PSC State: [chars]

The indicated PSC event on the tuunel interface has preempted the indicated psc event which is of lower priority. This message is to notify the NMS of changes.

-

LOG_STD_ACTION

MPLS_PSC-5-TYPE_MISMATCH

5-Notice

Tunnel-tp[dec] type mismatch local-type: [chars] remote-type: [chars]

The local protection type on the indicated MPLS-TP tunnel interface mismatches with the remote protection type. Local and remote protection types are provided.

-

"Examine the local and remote protection types and configure the remote " "protection type to the local protection type."

MPLS_PSC-5-REVERT_MISMATCH

5-Notice

Tunnel-tp[dec] revertive behaviour mismatch: local is [chars] but remote is [chars]

The local revertive mode for the indicated MPLS-TP tunnel interface mismatches with the remote revertive mode. Local and remote revertive modes are provided.

-

"Examine the local and remote revertive modes and configure the remote " "revertive mode to the local revertive mode."

MPLS_TP_LINK-5-CONFIG_CHANGED

5-Notice

Link [dec] interface [chars] next-hop [chars] [chars]

The configuration of the MPLS-TP link has changed. This message is to notify the NMS of changes.

-

LOG_STD_ACTION

MPLS_TP_LSP-3-UPDOWN

3-Error

[chars] LSP [chars] is [chars][chars][chars]

The indicated MPLS-TP LSP has gone up or down. If the LSP went down the failure condition and the fault source information is provided.

-

"Examine the failure condition and source information to determine why " "the LSP went down."

MPLS_TP_LSP-5-LOCKOUT

5-Notice

[chars] LSP [chars] [chars] lockout state

The indicated LSP has entered or exited lockout state due to administrative action at one endpoint

-

LOG_STD_ACTION

MPLS_TP_LSP-5-CONFIG_CHANGED

5-Notice

LSP [chars] is [chars]

The configuration of the MPLS-TP midpoint LSP has changed. This message is to notify the NMS of changes.

-

LOG_STD_ACTION

MPLS_LABEL-5-CHANGED

5-Notice

[chars] min/max label: [dec]/[dec]

The MPLS label range has changed. This message is to notify the NMS of changes.

-

LOG_STD_ACTION

MPLS_TP_BWPOOL-3- BW_POOL_CHANGED

3-Error

Bandiwdth pool available to MPLS-TP has changed

Bandwidth pool available to MPLS-TP has changed. This is either due to the removal of a link or changing to the pool through CLI configuration

mpls-tp

LOG_STD_ACTION

LDPLIB-3-GENERAL

3-Error

[chars]

Record associated with a withdrawn label has timed out before receiving acknowledgements from all peers.

mpls-ldp

"This is an informational message. This will not " "have any operational impact. The system will ignore any subsequently " "received release messages associated with the label."

LDPLIB-3-INIT

3-Error

Cannot allocate LIB

The LIB revision number used to manage advertisement of labels to LDP peers overflowed. This will result in faulty label distribution to LDP peers. The system recovers by toggling dynamic label switching off and on which forces the revision number to be re-initialized.

mpls-ldp

"None required."

LDP-3-GENERAL

3-Error

[chars]

-

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-3-CONSISTENCY

3-Error

[chars]

-

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-5-INFO

5-Notice

[chars]

This is an informational message generated by the Label\n\ Distribution Protocol LDP implementation.

mpls-ldp

ACTION_LOOPING_LSP

LDP-3-PTCLREAD

3-Error

peer [chars] read failure

An error occurred while attempting to read a LDP PDU received\n\ from a peer.

mpls-ldp

ACTION_NEW_SESSION_TDP

LDP-5-IDENT

5-Notice

cannot set [chars][chars] LDP ident

-

mpls-ldp

"This is an informational message. As long as it needs to set\n\ its chassis LDP identifier the system will periodically\n\ attempt to do so until it succeeds. If this message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative."

LDP-3-SM

3-Error

unexpected event: peer [chars][chars] state=[chars] event=[chars][chars]

An operation on the state machine for a LDP peer failed.

mpls-ldp

ACTION_IGNORE_REST_OF_PIE_TDP

LDP-3-KA_NOMEMORY

3-Error

Can't alloc KA message

An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP Keep Alive protocol message has failed.

mpls-ldp

"The system will continue by omitting transmission of the LDP\n\ Keep Alive Message. This may result in termination of one or more\n\ LDP sessions as the peers time out the sessions. If this\n\ message persists reduce other system activity if possible\n\ and call your technical service representative for\n\ assistance."

LDP-3-TAGATM_BAD_RANGE

3-Error

Interface [chars] Bad VPI/VCI range. Can't start a LDP session

The session parameters proposed by an LDP peer differ from those\n\ preferred by the platform. The differences are not sufficient to\n\ prevent the LDP session from being established but may have an\n\ impact on label distribution operation

mpls-ldp

"If the parameters identified relate to the optional path vector-based\n\ loop detection mechanism note that the IETF LDP specification\n\ recommends that when Loop Detection is enabled in a portion of a\n\ network it is recommended that all LSRs in that portion of the\n\ network be configured with Loop Detection enabled and with the\n\ same path vector limit. If the parameters identified relate\n\ to some other aspect of the LDP session and the message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative."

LDP-3-TAGATM_NOMEM

3-Error

Interface [chars] Resource failure. Can't start a LDP session

An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP TAGATM VPI/VCI ranges has failed.

mpls-ldp

"The system will not be able to create a LDP session between\n\ the affected LDP peers. If this message persists reduce \n\ other system activity if possible and call your technical \n\ service representative for assistance."

LDP-5-ACL

5-Notice

mpls ldp advertise-labels has no effect for lc-atm

EXPLANATION_ACL_TDP

mpls-ldp

"No action is required."

LDP-5-ACL1

5-Notice

mpls ldp advertise-labels has no effect for lc-atm

EXPLANATION_ACL_TDP

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-4-PTCL

4-Warning

peer [chars] [chars]

A violation of the LDP protocol by a LDP peer has been detected.

mpls-ldp

ACTION_NEW_SESSION_TDP

LDP-4-ADV

4-Warning

Label advertisement mode DU/DoD mismatch with peer [chars] resolved to [chars].

-

mpls-ldp

ACTION_NEW_SESSION_TDP

LDP-5-CLEAR_CHKPT

5-Notice

Clear [chars] checkpoint state [chars] by [chars]

Checkpoint state for one or more LDP objects has been reset

mpls-ldp

LOG_STD_NO_ACTION

LDP-3-ISYNC_CHKPT

3-Error

[chars]:: [chars] request failed [chars]

An unexpected condition happened while uncheckpointing

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-3-ISSU_XFORM

3-Error

ISSU [chars] transformation failed for msg type [dec][chars].

-

-

-

LDP-3-AUTOCFG

3-Error

Interface [chars] is in an unexpected autoconfig state 0x[hec] [chars] request.

An interface is in an unexpected LDP auto config state. This could\n\ impact the LDP session running on this interface

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-3-ISYNC

3-Error

[chars]

An unexpected error happened in LDP-IGP Synchronization operation.

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-5-NBRCHG

5-Notice

[chars] Neighbor [chars] is [chars][chars]

An LDP neighbor has either come up or gone down. The message\n\ describes the change for it.

mpls-ldp

"This informational message normally appears as routers and\n\ LDP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated."

LDP-5-CLEAR_NBRS

5-Notice

Clear LDP neighbors [chars] by [chars]

One or more LDP neighbor sessions has been reset

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-GR

5-Notice

[chars]

An informational LDP notice was generated for a Graceful Restart event.

mpls-ldp

LOG_STD_NO_ACTION

LDP-3-RECONNECT

3-Error

[chars]

An error occurred while parsing the incoming LDP Initialization message.\n\ The FT Reconnect Timer value received was greater than\n\ the locally-configured Forwarding State Holding Timer value.

mpls-ldp

"Reconfigure the Forwarding State Holding Timer value."

LDP-4-PWD

4-Warning

MD5 protection is required for peer [chars] no password configured

-

mpls-ldp

"This message indicates a misconfiguration on the router. If the\n\ user requires MD5 password protection for the LDP session configure\n\ a password for the LDP peer. If the user requires MD5 password\n\ protection for a subset of LDP neighbors but not for this specific\n\ LDP peer modify the LDP password configuration to exclude this LDP\n\ peer from the password required list. Otherwise if an LDP session\n\ should not exist disable MPLS to this neighbor."

LDP-5-SP

5-Notice

[chars]

An informational LDP notice was generated for a Session Protection event.

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-PWDCFG

5-Notice

Password configuration changed for [chars]

An informational LDP notice was generated to report password\n\ configuration change for a neighbor.

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-PWDRO

5-Notice

Password rolled over for [chars]

An informational LDP notice was generated to report lossless password\n\ change for a neighbor.

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-PWDKEYTRUNC

5-Notice

MD5 digest uses [dec] chars of longer [chars] keys for peer [chars]

-

mpls-ldp

"This message indicates a possible misconfiguration on the router.\n\ Ensure that you have configured your key chains correctly on each\n\ router. Your LDP session can be established if the MD5 key used by\n\ the specified LDP peer has been truncated by the same amount or is\n\ defined to be equal to the truncated key value on this router."

LDP-5-UNKNOWNCAP

5-Notice

Advertised Capability [chars] not supported by peer [chars]

This information message is returned by peer to assist in\n\ troubleshooting interop issues that may arise when a peer is\n\ not capable of supporting an advertised LDP capability

mpls-ldp

LOG_STD_NO_ACTION

LDP-4-CAPCHANGE

4-Warning

Reset of established LDP sessions required to propagate [chars]

A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers will not learn of the change until the LDP session has\n\ been reset.

mpls-ldp

"Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command."

LDP-4-CAPCHANGE_DYNAMIC

4-Warning

Reset of established LDP session required to propagate [chars]\n change to peers that don't support Dynamic Announcement

A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers that don't support Dynamic Announcement will not learn\n\ of the changeuntil the LDP session has been reset.

mpls-ldp

"Use the 'show mpls ldp neighbor capability' command to determine\n\ which neighbors need to be reset. Reset LDP neighbor using the\n\ 'clear mpls ldp neighbor ...' command."

LDP-4-MAXMSGSIZE

4-Warning

Maximum implementation message size exceeded actual [dec] maximum [dec]

This is an informational message that appears when LDP receives\n\ a request to allocate memory resources for an LDP message with\n\ a size exceeding the current implemented maximum.

mpls-ldp

"No action is required unless a larger message size is deemed to be\n\ required to support a new application. In this case the actual\n\ application should be identified and component owners contacted\n\ to increase the implemented maximum message size."

LCON-3-CONSISTENCY

3-Error

[chars]

An action attempted by the Label Control process encountered\n\ an unexpected condition.

mpls-ldp

"The request will be ignored. If it repeatedly occurs\n\ copy the message exactly as it appears and report it to your\n\ technical service representative."

LCON-3-ALLOC

3-Error

Cannot alloc [chars]

An attempt to allocate a LDP data structure failed\n\ because of a low memory condition.

mpls-ldp

ACTION_STD_LOW_MEMORY_TAGCON

LCON-3-PROCESS

3-Error

process not created

An attempt to create the label distribution and control process\n\ failed. The probable cause is insufficient memory.

mpls-ldp

ACTION_STD_LOW_MEMORY_TAGCON

LCON-3-INIT

3-Error

process cannot initialize

The label distribution and control process failed to initialize\n\ itself. The probable cause is insufficient memory.

mpls-ldp

ACTION_STD_LOW_MEMORY_TAGCON

LCON-4-INIT_TAG_ALLOC

4-Warning

Failure to initialize label allocation pool [dec]

The system was unable to initialize the data structure used to support\n\ allocation of labels for label switching for the specified label pool.

mpls-ldp

-

LCON-5-SEND

5-Notice

cannot queue LDP [chars] message for [chars][chars]

-

mpls-ldp

"This is an informational message. Failure to queue a message for\n\ a peer should occur only when the LDP session with the peer no\n\ longer exists. The software should recover from this\n\ situation by discarding the LDP session and trying to\n\ establish a new one. If this message occurs repeatedly copy\n\ it exactly as it appears and report it to your technical\n\ service representative."

LCON-3-PEERSM

3-Error

LDP peer [chars][chars]: [chars]

An operation on the state machine for the label distribution and\n\ control process failed.

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-DEADADJ

3-Error

[chars] [chars]

An unexpected failure occurred while building a LDP protocol\n\ message for transmission to a LDP peer. It occurred when\n\ attempting to add a label binding or an address to the message.

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-RADIXTREE

3-Error

[chars]LIB walk failed [chars]

-

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-LDPID

3-Error

peer [chars] LDP Id/Addr mapping problem [chars]

EXPLANATION_ADDR_TBL_TAGCON

mpls-ldp

ACTION_TOGGLE_TAG_IP_TAGCON

LCON-3-DUP_ADDR_RCVD

3-Error

Duplicate Address [chars] advertised by peer [chars] is already bound to [chars]

EXPLANATION_ADDR_TBL_TAGCON

mpls-ldp

ACTION_TOGGLE_TAG_IP_TAGCON

LCON-3-DEFCASE_BINDING_PIE

3-Error

Unexpected blist_type [dec] for [chars] message from peer [chars]

A LDP protocol message received from a LDP peer contained an\n\ unexpected binding list type. The message will be be ignored.

mpls-ldp

ACTION_IGNORE_PIE_TAGCON

LCON-3-REGISTRY

3-Error

Unexpected [chars] for reg_invoke_[chars]

-

mpls-ldp

-

LCON-4-ADDR_PROC

4-Warning

Can't create lcon addr proc

-

mpls-ldp

"This is an informational message. As long as it needs the\n\ process the system will regularly attempt to create it. If\n\ this message occurs repeatedly copy it exactly as it appears\n\ and report it to your technical service representative."

LCON-4-ADDRQ

4-Warning

Can't alloc work item for [chars]

-

mpls-ldp

"This is an informational message. The system remembers that\n\ it needs to do this work and will regularly attempt to queue\n\ the necessary work item. If this message occurs repeatedly\n\ copy it exactly as it appears and report it to your technical\n\ service representative."

LCON-3-EVENTQ

3-Error

Can't alloc work item for [chars]

An operation on the LDP Directed Adjacency data structure\n\ failed.

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-LATREVNUMWRAP

3-Error

Label Local Address Table revision number wrapped

The revision number used to manage advertisement of interface\n\ addresses to LDP peers overflowed. This will result in faulty\n\ advertisement of interface addresses to LDP peers and\n\ faulty label switching on those peers.

mpls-ldp

"To restore proper interface address advertisement reboot the\n\ platform. Report this condition to your technical service\n\ representative."

LCON-3-LCLTAG_ALLOC

3-Error

Cannot allocate local label

-

mpls-ldp

"The number of labels available for allocation can be changed\n\ by the <CmdBold>mpls label range ...<NoCmdBold> configuration command.\n\ Consult with your technical service representative to determine\n\ whether you should use this command to increase the number of\n\ available labels."

LCON-3-LABEL_REGION

3-Error

Platform specified information for label region [chars] is invalid.

A platform service routine provides label region information about\n\ all label regions it supports. This error message is printed when\n\ the service routine does not specify its label region information\n\ correctly.

mpls-ldp

"Report this condition to your technical service representative."

LCON-4-CFGD_LBL_REGION

4-Warning

Adjusting configured label range to default range

The saved configuration has been ignored and the default label range\n\ is being used.

mpls-ldp

"Please reconfigure the label range to a valid range using <CmdBold>\n\ mpls label range ... <NoCmdBold> configuration command."

ICPM-3-ALLOC

3-Error

Cannot alloc [chars]

An attempt to allocate an ICPM data structure failed because\n\ of a low memory condition.

mpls-ldp

ACTION_STD_LOW_MEMORY_ICPM

GENERAL-3-LDPLIB

3-Error

ERRMSG_NOFLAGS

-

-

-

INIT-3-LDPLIB

3-Error

ERRMSG_NOFLAGS

-

-

-

GENERAL-3-LDP

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

CONSISTENCY-3-LDP

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

INFO-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

PATH_VEC-4-LDP

4-Warning

ERRMSG_LIMIT_SLOW*15

-

-

-

PTCLREAD-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

IDENT-4-LDP

4-Warning

ERRMSG_LIMIT_SLOW*15

-

-

-

SM-3-LDP

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

KA_NOMEMORY-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

TAGATM_BAD_RANGE-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

TAGATM_NOMEM-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

ACL-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

ACL1-5-LDP

5-Notice

5*ERRMSG_LIMIT_SLOW

-

-

-

PTCL-4-LDP

4-Warning

ERRMSG_NOFLAGS

-

-

-

ADV-4-LDP

4-Warning

ERRMSG_NOFLAGS

-

-

-

CLEAR_CHKPT-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

ISYNC_CHKPT-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

ISSU_XFORM-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

AUTOCFG-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

ISYNC-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

NBRCHG-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

CLEAR_NBRS-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

GR-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

RECONNECT-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

PWD-4-LDP

4-Warning

ERRMSG_NOFLAGS

-

-

-

SP-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

PWDCFG-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

PWDRO-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

PWDKEYTRUNC-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

UNKNOWNCAP-5-LDP

5-Notice

ERRMSG_NOFLAGS

-

-

-

CAPCHANGE-4-LDP

4-Warning

ERRMSG_NOFLAGS

-

-

-

CAPCHANGE_DYNAMIC-4-LDP

4-Warning

ERRMSG_NOFLAGS

-

-

-

MAXMSGSIZE-4-LDP

4-Warning

ERRMSG_LIMIT_SLOW*15

-

-

-

CONSISTENCY-3-LCON

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

ALLOC-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

PROCESS-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

INIT-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

INIT_TAG_ALLOC-4-LCON

4-Warning

ERRMSG_NOFLAGS

-

-

-

SEND-5-LCON

5-Notice

ERRMSG_NOFLAGS

-

-

-

PEERSM-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

DEADADJ-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

RADIXTREE-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

LDPID-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

DUP_ADDR_RCVD-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

DEFCASE_BINDING_PIE-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

REGISTRY-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

ADDR_PROC-4-LCON

4-Warning

ERRMSG_NOFLAGS

-

-

-

ADDRQ-4-LCON

4-Warning

ERRMSG_NOFLAGS

-

-

-

EVENTQ-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

LATREVNUMWRAP-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

LCLTAG_ALLOC-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

LABEL_REGION-3-LCON

3-Error

ERRMSG_NOFLAGS

-

-

-

CFGD_LBL_REGION-4-LCON

4-Warning

ERRMSG_NOFLAGS

-

-

-

SM_CREATE-2-LDP

2-Critical

ERRMSG_NOFLAGS

-

-

-

MALLOC-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

SLAB_CREATE-2-LDP

2-Critical

ERRMSG_NOFLAGS

-

-

-

SLAB_ALLOC-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

INIT-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

STARTTHREAD-1-LDP

1-Alert

ERRMSG_NOFLAGS

-

-

-

THREADEXIT-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

REGISTRATION_FAIL-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

CLIENT-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

SHUTDOWN_REQUEST_FAIL-6-LDP

6-Information

ERRMSG_NOFLAGS

-

-

-

DECONFIG_SHUTDOWN-6-LDP

6-Information

ERRMSG_NOFLAGS

-

-

-

RESTART_SHUTDOWN-4-LDP

4-Warning

ERRMSG_NOFLAGS

-

-

-

UNKNOWN_SHUTDOWN-6-LDP

6-Information

ERRMSG_NOFLAGS

-

-

-

REG_COMP-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

SIGNAL-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

XIPC-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

TIMER-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

THREAD-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

NOTIFY_BUFFER-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

SNMP_FILL-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

CLNT_REG-7-LDP

7-Debug

ERRMSG_NOFLAGS

-

-

-

API_BAD_ARGUMENTS-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

API_MSG-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

API_BAD_RESPONSE-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

API_FAILED-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_UNKNOWN_MSG-6-LDP

6-Information

ERRMSG_NOFLAGS

-

-

-

MTS_RECV-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_DROP-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

SYSMGR_SRV_QUERY-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

HA_TLV-2-LDP

2-Critical

ERRMSG_NOFLAGS

-

-

-

SDB_UPDATE-2-LDP

2-Critical

ERRMSG_NOFLAGS

-

-

-

UNAWAKABLE-3-LDP

3-Error

ERRMSG_NOFLAGS

-

-

-

UNEXPECTEDEVENT-3-LDP_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

UNEXPECTEDTIMER-3-LDP_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

UNEXPECTEDMESSAGE-3-LDP_SCHED

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

UNEXPECTEDMESSAGE-3-LDP_SCHED

3-Error

-

MPLS_LDP Service nabled

SRVNAME_LDP

SYSLOGDOC_NO_ACTION

UNEXPECTEDMESSAGE-3-LDP_SCHED

3-Error

-

MPLS_LDP Service Disabled

SRVNAME_LDP

SYSLOGDOC_NO_ACTION

ALLOC-3-ICPM

3-Error

ERRMSG_NOFLAGS

-

-

-

MPLSOAM-3-XDR_COMM

3-Error

[chars]:0x[hec] 0x[hec]

XDR Comm module - Unexpected RP/LC XDR condition encountered in MPLS OAM software. This may result in MPLS OAM FIB sub-blocks becoming out of synchronization between RP and LC. This should not affect overall system.

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-WALK_CONSUMED

3-Error

[chars]

FWD RPLC Module - Walk packet unexpectedly consumed in MPLS OAM software. This should not affect overall system performance.

mpls-oam

LOG_STD_ACTION

LSPV-3-COMM_UNKNOWN_RC

3-Error

Unexpected oce return code

Comm module - unexpected oce return code encountered

mpls-oam

LOG_STD_ACTION

LSPV-3-TP_ECHO_REQUEST

3-Error

MPLS-TP Echo request unsupported

MPLS-TP echo request was received. Ignoring as MPLS-TP is not supported on this platform

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-UNAUTH_PROXY_REQ

3-Error

Unauthorized proxy request - dropping packet

MPLS-OAM proxy echo request was received. It was unauthorized and hence dropped.

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-XDR_COMM

3-Error

[chars]:0x[hec] 0x[hec]

XDR Comm module - Unexpected RP/LC XDR condition encountered in MPLS OAM software. This may result in MPLS OAM FIB sub-blocks becoming out of synchronization between RP and LC. This should not affect overall system.

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-WALK_CONSUMED

3-Error

[chars]

FWD RPLC Module - Walk packet unexpectedly consumed in MPLS OAM software. This should not affect overall system performance.

mpls-oam

LOG_STD_ACTION

LSPV-3-COMM_UNKNOWN_RC

3-Error

Unexpected oce return code

Comm module - unexpected oce return code encountered

mpls-oam

LOG_STD_ACTION

LSPV-3-TP_ECHO_REQUEST

3-Error

MPLS-TP Echo request unsupported

MPLS-TP echo request was received. Ignoring as MPLS-TP is not supported on this platform

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-UNAUTH_PROXY_REQ

3-Error

Unauthorized proxy request - dropping packet

MPLS-OAM proxy echo request was received. It was unauthorized and hence dropped.

mpls-oam

LOG_STD_ACTION

XDR_COMM-3-MPLSOAM

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

COMM_UNKNOWN_RC-3-LSPV

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

COMM_UNKNOWN_RC-3-LSPV

3-Error

-

MPLS_LSPV Service nabled

SRVNAME_MPLS_OAM

SYSLOGDOC_NO_ACTION

COMM_UNKNOWN_RC-3-LSPV

3-Error

-

MPLS_LSPV Service Disabled

SRVNAME_MPLS_OAM

SYSLOGDOC_NO_ACTION

COMM_UNKNOWN_RC-3-LSPV

3-Error

-

MPLS OAM Daemon Initialization failed. [chars] explains the reason for the failure.

SYSLOGDOC_NO_DDTS

SYSLOGDOC_NO_ACTION

COMM_UNKNOWN_RC-3-LSPV

3-Error

-

-

-

-

DEAD-4-SCARLET

4-Warning

* Interface [chars]: I knew without asking she was into the blues

-

-

-

DEAD-4-SCARLET

4-Warning

-

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

CFC_SRV6-3-DISPATCH_OCE

3-Error

Failed to [chars] SRv6 dispath oce [chars][chars]

-

-

-

CFC_SRV6-3-END_OCE

3-Error

Failed to [chars] SRv6 end oce [chars][chars]

An internal software error occurred.

CFC_SRV6_MSG_DDTS_COMP

LOG_STD_ACTION

SR-5-SR_POLICY_UPDOWN

5-Notice

POLICY [chars] [chars]

A policy has either come up or gone down.The message describes the change for it.

sr

" This informational message normally appears as a policy go up or down"

SR-5-SR_POLICY_UPDOWN

5-Notice

POLICY [chars] [chars]

A policy has either come up or gone down.The message describes the change for it.

sr-policy-mgr

" This informational message normally appears as a policy go up or down"

SR-3-SR_POLICY_UNLOCK

3-Error

Try to decrease zero refcount for policy %p

Attempt to decrease the refcount of policy when it is already zero.

sr-policy-mgr

LOG_STD_ACTION

OIRLIB-4-NOTRACE

4-Warning

OIR-LIB trace initialization failed[dec]

-

-

-

XMCP-4-CLIENT_ERR_RSP

4-Warning

Received error response [dec] [chars] from client [chars]/[chars]

-

-

-

XMCP-4-CLIENT_DENIED

4-Warning

Client [chars]/[chars] denied: [chars]

An external XMCP client connection was denied. This may be due to a valid configuration reason for example <CmdBold>max-clients<NoCmdBold> or an <CmdBold>allow-list<NoCmdBold> or it may indicate that a protection mechanism has been triggered - for example an authentication failure or DOS attack prevention

-

"Check that this is caused by configuration. If not " "and if the frequency of this message suggests that " "this may be malicious - contant your TAC security " "support immediately"

XMCP-5-CLIENT_CHANGE

5-Notice

Client [chars]/[chars] is [chars]: [chars]

An XMCP client connected or disconnected.

-

LOG_STD_NOACTION

XMCP-5-CLIENT_CHANGE

5-Notice

-

An error occurred during initialization

SISF_COMP_NAME

LOG_STD_ACTION

XMCP-5-CLIENT_CHANGE

5-Notice

-

An internal software error occurred.

SISF_COMP_NAME

LOG_STD_ACTION

XMCP-5-CLIENT_CHANGE

5-Notice

-

A PSS operation was performed

SISF_COMP_NAME

"This is an informationnal message"

XMCP-5-CLIENT_CHANGE

5-Notice

-

An entry was created in the binding table

SISF_COMP_NAME

"This is an informationnal message"

XMCP-5-CLIENT_CHANGE

5-Notice

-

An entry was created in the binding table

SISF_COMP_NAME

"This is an informationnal message"

XMCP-5-CLIENT_CHANGE

5-Notice

-

An entry was changed in the binding table

SISF_COMP_NAME

"This is an informationnal message"

XMCP-5-CLIENT_CHANGE

5-Notice

-

Reached 80% of maximum # addresses for the target

SISF_COMP_NAME

"A client is approaching red zone and might soon \n\ be blocked. The maximum value configured may be too low \n\ and you should consider increasing it. Or some of this client addresses are \n\ stale and you could clear them"

XMCP-5-CLIENT_CHANGE

5-Notice

-

An attempt to install an entry in the IPv6 binding table was blocked. This can be due to a conflicting entry or maximum number of entries reached

SISF_COMP_NAME

"If the maximum table size is reached consider increasing it.\n\ If a conflicting entry already exist this maybe an attempt \n\ to steal address ownership. You should investigate which host\n\ is connected on the interface and wether it should be disconnected"

XMCP-5-CLIENT_CHANGE

5-Notice

-

A duplicate IP address has been detected IP theft and blocked This can be due to a configuration error on end-device an intentional IP theft or an IP movind too quickly

sisf

"If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved"

XMCP-5-CLIENT_CHANGE

5-Notice

-

A duplicate MAC address has been detected MAC theft and blocked This can be due to a configuration error on end-device an intentional MAC theft or MAC moving too quickly

SISF_COMP_NAME

"If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved"

XMCP-5-CLIENT_CHANGE

5-Notice

-

A duplicate MAC and IP address has been detected MAC_AND_IP theft and blocked This can be due to a configuration error on end-device an intentional MAC_AND_IP theft or MAC moving too quickly

SISF_COMP_NAME

"If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved"

XMCP-5-CLIENT_CHANGE

5-Notice

-

-

-

-

-

5-Notice

0

-

-

-

-

5-Notice

-

A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table.

SISF_COMP_NAME

-

-

5-Notice

-

-

ipv6

"A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests"

SISF-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

sisf

LOG_STD_ACTION

SISF-6-ENTRY_CREATED

6-Information

Entry created [chars]

An entry was created in the binding table

sisf

"This is an informationnal message"

SISF-6-ENTRY_DELETED

6-Information

Entry deleted [chars]

An entry was created in the binding table

sisf

"This is an informationnal message"

SISF-6-ENTRY_CHANGED

6-Information

Entry changed [chars]

An entry was changed in the binding table

sisf

"This is an informationnal message"

SISF-6-ENTRY_MAX_ORANGE

6-Information

Reaching 80%% of max adr allowed per [chars]

Reached 80% of maximum # addresses for the target

sisf

"A client is approaching red zone and might soon \n\ be blocked. The maximum value configured may be too low \n\ and you should consider increasing it. Or some of this client addresses are \n\ stale and you could clear them"

SISF-4-ENTRY_BLOCKED

4-Warning

Entry blocked [chars]

An attempt to install an entry in the IPv6 binding table was blocked. This can be due to a conflicting entry or maximum number of entries reached

sisf

"If the maximum table size is reached consider increasing it.\n\ If a conflicting entry already exist this maybe an attempt \n\ to steal address ownership. You should investigate which host\n\ is connected on the interface and wether it should be disconnected"

SISF-4-IP_THEFT

4-Warning

IP Theft [chars]

A duplicate IP address has been detected IP theft and blocked This can be due to a configuration error on end-device an intentional IP theft or an IP movind too quickly

sisf

"If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved"

SISF-4-MAC_THEFT

4-Warning

MAC Theft [chars]

A duplicate MAC address has been detected MAC theft and blocked This can be due to a configuration error on end-device an intentional MAC theft or MAC moving too quickly

sisf

"If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved"

SISF-4-MAC_AND_IP_THEFT

4-Warning

MAC_AND_IP Theft [chars]

A duplicate MAC and IP address has been detected MAC_AND_IP theft and blocked This can be due to a configuration error on end-device an intentional MAC_AND_IP theft or MAC moving too quickly

sisf

"If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved"

SISF-4-PAK_DROP

4-Warning

Message dropped [chars]

-

-

-

SISF-4-PAK_DROP

4-Warning

Message dropped [chars]

A message was dropped because one of the IPv6 first-hop \n\ security features said so

sisf

"Look at the reason. It can either be a valid drop and the \n\ could go up to disconnect the host attached to the interface \n\ or the policy configured on this interface is too severed \n\ and should be amended"

SISF-4-DATA_GLEAN_NOTIF_RECEIVED

4-Warning

No binding for [chars]

A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table.

sisf

-

SISF-4-RESOLUTION_VETO

4-Warning

Resolution vetoed [chars]

-

ipv6

"A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests"

SISF_TRACKING_HA-4-ENTRY_OUT_OF_SYNC

4-Warning

Host mac-address [enet] ip-address [inet] interface [chars]

An inconsistency has been detected in the IP device tracking table for this host between active and standby

ipv6

LOG_STD_NO_ACTION

SISF_ISSU-2-INIT

2-Critical

Sisf ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Sisf ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ipv6

LOG_STD_ACTION

SISF_ISSU-3-TRANSFORM_FAIL

3-Error

Sisf ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Sisf ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Sisf state between the active device and the standby device is not identical.

ipv6

"show issu session <client_id> and " "show issu negotiated version <session_id>"

SISF_ISSU-3-MSG_NOT_OK

3-Error

Sisf ISSU client 'Message Type [dec]' is not compatible

The Sisf ISSU client received an incompatible message from the peer device. The message cannot be processed.

ipv6

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SISF_ISSU-3-MSG_SIZE

3-Error

Sisf ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Sisf ISSU client failed to calculate the MTU for the specified message. The Sisf ISSU client is not able to send the message to the standby device.

ipv6

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SISF_ISSU-3-INVALID_SESSION

3-Error

Sisf ISSU client does not have a valid registered session.

The Sisf ISSU client does not have a valid registered session.

ipv6

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SISF_ISSU-2-SESSION_REGISTRY

2-Critical

Sisf ISSU client failed to register session information. Error: [dec] [chars]

The Sisf ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ipv6

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SISF_ISSU-3-SESSION_UNREGISTRY

3-Error

Sisf ISSU client failed to unregister session information. Error: [dec] [chars]

The Sisf ISSU client failed to unregister session information.

ipv6

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SISF_ISSU-2-SESSION_NEGO

2-Critical

Sisf ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Sisf ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ipv6

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SISF_ISSU-2-SEND_NEGO_FAILED

2-Critical

Sisf ISSU client failed to send negotiation message. Error: [dec] [chars]

The Sisf ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ipv6

"show logging and show checkpoint client"

SISF_ISSU-2-GET_BUFFER

2-Critical

Sisf ISSU client failed to get buffer for message. Error: [dec] [chars]

The Sisf ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ipv6

"show logging and show checkpoint client"

SISF_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

Sisf ISSU client capability exchange result incompatible.

The Sisf ISSU client capability exchange have negotiated as incompatible with the peer.

ipv6

"show issu negotiated capability <Session_ID>"

SISF_ISSU-3-CAP_INVALID_SIZE

3-Error

SISF ISSU client capability list is empty.

The SISF ISSU client capability exchange list size is invalid.

ipv6

"show issu capability entires <Client_ID>"

CALL_HOME-3-HTTP_REQUEST_FAILED

3-Error

Failure to send HTTP request to: [chars] ERR [dec] : [chars]

-

-

-

CALL_HOME-5-SL_MESSAGE_FAILED

5-Notice

Fail to send out Smart Licensing message to: [chars] ERR [dec] : [chars]

-

-

-

CALL_HOME-5-HTTPS_NOT_SUPPORTED

5-Notice

This image version does not support HTTPS

This image does not support secure HTTP although user configures https url

call-home

"Please upgrade your system image to a crypto image which supports" "secure http."

CALL_HOME-4-HTTP_ADDRESS_NOT_SUPPORTED

4-Warning

Http will be or has been disabled on Smart Call Home Server please change the address [chars] to https address for profile [chars]. Otherwise call-home will fail to send messages

Http will be or has benn disabled on Smart Call Home Server call-home will fail to send message to the http destination

call-home

"Please change the http address to https address."

CALL_HOME-3-SMTP_SEND_FAILED

3-Error

Unable to send notification using all SMTP servers ERR [dec] [chars]

-

-

-

CALL_HOME-3-CLI_CMD_RUN_FAILED

3-Error

No VTY connection available to run CLI command for event notification message ERR [dec] [chars]

-

-

-

CALL_HOME-3-MESSAGE_SIZE_OVER_LIMIT

3-Error

XML message size over limit failed to send call-home message. configured message size limit [dec] is less than current message

Unable to create message because configured message size limit is smaller than current message minimum length required.

call-home

"Please re-config the destination message-size-limit."

CALL_HOME-4-MESSAGE_IS_TRUNCATED

4-Warning

message size over limit call-home message is truncated. configured message size limit [dec] is less than current message

call-home message is truncated because configured message size limit is smaller than current message total length required.

call-home

"Please re-config the destination message-size-limit."

CALL_HOME-3-REQUEST_MESSAGE_FAILED

3-Error

call-home request message failed to send ERR [dec] [chars]

-

-

-

CALL_HOME-6-REQUEST_MESSAGE_SUCCEEDED

6-Information

call-home request message succeeded

call-home request message was sent successfully.

call-home

"No action is needed. This is informational message."

CALL_HOME-3-ONDEMAND_MESSAGE_FAILED

3-Error

The call-home on-demand message failed to send for [chars][chars]s

The call-home on-demand message failed.

call-home

"Reconfigure call-home to send call-home on-demand messages."

CALL_HOME-6-DS_UPDATE_SUCCESS

6-Information

call-home diagnostic-signature successfully did [chars] download [dec] new diagnostic-signatures will be added

call-home diagnostic-signature downloaded successfully.

call-home

"No action is required."

CALL_HOME-3-DS_UPDATE_FAIL

3-Error

The call-home diagnostic-signature failed to update.

The call-home diagnostic-signature failed to update.

call-home

"Please check the \"show call-home diagnostic-signature failure\" " "command for details."

CALL_HOME-6-DS_UNDECLARED_VARS

6-Information

There're undeclared variables referenced in DS [chars] please use \show call-home diagnostic-signature <ds-id> variables\ to check it. If they're environment variables please configure them to make DS work as expected.

call-home DS file has undeclared variables.It will not work until users configure it.

call-home

"Please check undeclared variables in the DS."

CALL_HOME-6-DS_PROFILE_HTTP_NOT_SET

6-Information

The Email transport method is currently selected for the Smart Call Home service. To download the Diagnostic Signature from the Smart Call Home Server the HTTP transport method must be enabled and a destination HTTP URL must be configured in the [chars] profile.

The call-home diagnostic-signature update will not start because the HTTP transport method is disabled or the URL destination is not configured in the diagnostic-signature profile.

call-home

"This message is informational only."

CALL_HOME-6-DS_REMEDIATION_ACTION

6-Information

The call-home diagnostic-signature [chars] action was performed. Device status such as configuration or line card status may be affected.

The call-home diagnostic-signature remediation actions were performed

call-home

"No action is required."

CALL_HOME-3-CREATE_EVENT_FAILED

3-Error

Failed to create [chars] event for profile [chars]

The call-home event creation failed.

call-home

"Unsubscribe and then subscribe again to that alert group for " "the specified profile."

CALL_HOME-3-DS_DIR_CREATE_FAIL

3-Error

Failed to create diagnostic-signature directory [chars] fail reason: [chars].

The diagnostic-signature directory creation failed.

call-home

"Please check the disk/flash status first and then create the " "diagnostic-signature directory by yourself."

CALL_HOME-5-DS_ACTION_MSG

5-Notice

Notification message from diagnostic-signature file [chars]: [chars]

Notification message from call-home diagnostic-signature because the message action defined in it was performed.

call-home

"No action is required."

CALL_HOME-6-SCH_REGISTRATION_IN_PROGRESS

6-Information

Device registration with Smart Call HomeSCH is in progress.

SCH device registration is in progress after a Smart licensing registration message was received. Call-home will poll SCH server for the registration result.

call-home

"No action is required."

CALL_HOME-6-UPDATE_SCH_REGISTRATION_STATUS

6-Information

Device SCH registration result: [chars]. The result has no impact on Smart Licensing registration. You can check Smart Licensing registration status by executing command \show license summary\.

Call-home retrieved and printed out the registration result from SCH server.

call-home

"No action is required."

CALL_HOME-3-FAIL_TO_RETRIEVE_SCH_STATUS

3-Error

Fail to retrieve device registration result. Please check SCH registration status with \call-home request registration-info\ under EXEC mode.

Fail to retrieve device registration result. Call-home will abort polling progress.

call-home

"Please check SCH registration status with \"call-home request " "registration-info\" under EXEC mode."

CALL_HOME-6-CALL_HOME_ENABLED

6-Information

Call-home is enabled by Smart Agent for Licensing.

Call-home is enabled by Smart Agent for Licensing.

call-home

"No action is required."

CALL_HOME-3-CALL_HOME_FAILED_TO_ENABLE

3-Error

Failed to enable call-home from Smart Agent for Licensing: [chars]

Failed to enable call-home from Smart Agent for Licensing. Call-home and Smart Licensing could not work properly.

call-home

"Please enable call-home manually according to the error string."

BFDFSM-3-NULLMACH

3-Error

Invalid machine pointer 0x%X

state machine invalid pointer

bfd

LOG_STD_ACTION

BFDFSM-3-INVSTATE

3-Error

Invalid current state 0x%X

state machine invalid state

bfd

LOG_STD_ACTION

BFDFSM-3-INVEVENT

3-Error

Invalid event_id 0x%X

state machine invalid event

bfd

LOG_STD_ACTION

BFDFSM-3-INVTRANS

3-Error

obj: [0x%08X] event_id: [0x%08X] er_p: [0x%08X] arg: [0x%08X] session state [chars] -> [chars]

state machine invalid transition

bfd

LOG_STD_ACTION

BFDFSM-3-NOEVENT

3-Error

Unable to apply event 0x%08X

state machine transition failure

bfd

LOG_STD_ACTION

BFDFSM-6-BFD_SESS_DOWN

6-Information

BFD-SYSLOG: BFD session [chars] is going Down Reason: [chars]

bfd session down

bfd

LOG_STD_NO_ACTION

BFDFSM-6-BFD_SESS_UP

6-Information

BFD-SYSLOG: BFD session [chars] is going UP

bfd session Up

bfd

LOG_STD_NO_ACTION

BFD_CFG-3-MALLOC_CFG

3-Error

Malloc failure [chars] [chars]

malloc failure

bfd

LOG_STD_ACTION

BFD_CFG-3-MALLOC

3-Error

Malloc failure [chars]

malloc failure

bfd

LOG_STD_ACTION

BFD_CFG-3-WAVL_INSERT_FAIL

3-Error

Wavl insert failed [chars] [chars]

wavl insert failed.

bfd

LOG_STD_ACTION

BFD_CFG-3-WAVL_DELETE

3-Error

Wavl delete failed for %p

wavl delete failed.

bfd

LOG_STD_ACTION

BFD_CFG-3-WAVL_INIT_FAIL

3-Error

Failed initializing wavl tree

wavl_init failed.

bfd

LOG_STD_ACTION

BFD_MPLS-3-CFC_REG_FAIL

3-Error

CFC registration failed rc [dec]

CFC registration failed.

bfd

LOG_STD_ACTION

BFD_MPLS-3-CFC_UNREG_FAIL

3-Error

CFC unregistration failed rc [dec]

CFC unregistration failed.

bfd

LOG_STD_ACTION

BFD_MPLS-3-TP_LSP

3-Error

Session not created for intf [chars]/lsp [dec]. In-label [dec] in use for intf [chars]/lsp [dec]

BFD session mismatch.

bfd

LOG_STD_ACTION

BFD_MAP-3-MALLOC_MAP

3-Error

Malloc failure [chars] [chars]

malloc failure

bfd

LOG_STD_ACTION

BFD_MAP-3-MALLOC

3-Error

Malloc failure [chars]

malloc failure

bfd

LOG_STD_ACTION

BFD_MAP-3-WAVL_INSERT_FAIL

3-Error

Wavl insert failed [chars] [chars]

wavl insert failed.

bfd

LOG_STD_ACTION

BFD_MAP-3-WAVL_DELETE

3-Error

Wavl delete failed for %p

wavl delete failed.

bfd

LOG_STD_ACTION

BFD_MAP-3-WAVL_INIT_FAIL

3-Error

Failed initializing wavl tree

wavl_init failed.

bfd

LOG_STD_ACTION

BFD-3-INVVER

3-Error

Invalid version type

invalid version type

bfd

LOG_STD_ACTION

BFD-3-NOKADIS_TICK

3-Error

Failed to get kadis timer tick to start kadis timer.

kadis failed to get timer tick

bfd

LOG_STD_ACTION

BFD-3-NOKADIS

3-Error

Failed to start Kadis. Status [dec]

kadis failed to start

bfd

LOG_STD_ACTION

BFD-3-NOPPPROC

3-Error

Failed to create BFD PP Process

pseudo-preemptive process failed to start

bfd

LOG_STD_ACTION

BFD-3-NOBOOLEAN

3-Error

Failed to create watched boolean

could not create watched boolean

bfd

LOG_STD_ACTION

BFD-3-NOIOUPROC

3-Error

Failed to create BFD IOU Process

IOU process failed to start

bfd

LOG_STD_ACTION

BFD-3-CHUNK

3-Error

Chunk malloc failure - [chars] - 0x%X

chunk malloc failure

bfd

LOG_STD_ACTION

BFD-3-CHUNK_DESTROY

3-Error

Unable to destroy [chars] [chars]

chunk destroy failure

bfd

LOG_STD_ACTION

BFD-3-INVQELEM

3-Error

Invalid queue element - [chars]

invalid queue element

bfd

LOG_STD_ACTION

BFD-3-NOCLIENT

3-Error

Client not found

client does not exist in client list

bfd

LOG_STD_ACTION

BFD-3-PACKET

3-Error

bfd_pak_coalesce - [chars] failed

could not obtain or coalesce packet buffer

bfd

LOG_STD_ACTION

BFD-3-BUFPOOL

3-Error

Creation of BFD Private Buffer Pool failed

could not create private buffer pool

bfd

LOG_STD_ACTION

BFD-3-ILL_IF

3-Error

Illegal interface [dec][chars]

interface number is out of range for platform

bfd

LOG_STD_ACTION

BFD-3-IF_IN_USE

3-Error

Interface [chars][dec] already in use

interface number is already in use

bfd

LOG_STD_ACTION

BFD-3-NO_TYPE

3-Error

Neighbor address type not specified as ADDR_IP[dec] [dec]

-

-

-

BFD-3-WAVL_INSERT_FAIL_IPV4

3-Error

Failed inserting node for neighbor [inet] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INSERT_FAIL_IPV6

3-Error

Failed inserting node for neighbor %39P to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INSERT_FAIL_MPLS_PW

3-Error

Failed inserting node for neighbor [inet] : vcid [dec] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INSERT_FAIL_MPLS_TP_LSP

3-Error

Failed inserting node for LSP [chars] [chars] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INSERT_FAIL_MPLS_TE_GAL_LSP

3-Error

Failed inserting node for LSP [chars] [dec] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INSERT_FAIL_MPLS_TE_SR_LSP

3-Error

Failed inserting node for LSP [chars] [dec] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INSERT_FAIL_POCH_IPV4

3-Error

Failed inserting node for neighbor [inet] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_IPV4

3-Error

Failed deleting node for neighbor [inet] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_IPV6

3-Error

Failed deleting node for neighbor %39P to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_MPLS_PW

3-Error

Failed deleting node for neighbor [inet] : vcid [dec] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_MPLS_TP_LSP

3-Error

Failed deleting node for LSP [chars] [chars] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_MPLS_TE_GAL_LSP

3-Error

Failed deleting node for LSP [chars] [dec] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_MPLS_TE_SR_LSP

3-Error

Failed deleting node for LSP [chars] [dec] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_DELETE_FAIL_POCH_IPV4

3-Error

Failed deleting node for neighbor [inet] to wavl tree thread [dec] [chars]

-

-

-

BFD-3-WAVL_INIT_FAIL

3-Error

Failed initializing wavl tree.

wavl_init failed.

bfd

LOG_STD_ACTION

BFD-3-WAVL_TREE

3-Error

Failed to malloc space for wavl tree.

wavl tree malloc failed.

bfd

LOG_STD_ACTION

BFD-6-MAX_SESSION

6-Information

Maximum session creation limit [dec] for [chars] sessions reached.

Max. sessions created

bfd

LOG_STD_ACTION

BFD-6-MAX_DESCR

6-Information

BFD discrminators exhausted. No more sessions can be created.

Max. discriminators assigned

bfd

LOG_STD_ACTION

BFD-6-TX_ON_STANDBY

6-Information

BFD transmit detected on standby

BFD packet transmission on standby

bfd

LOG_STD_ACTION

BFD-6-TIMER_NOT_SUPP

6-Information

BFD timer value on interface [chars] is below the supported value of [dec] ms

Fast timers not supported on slow interface

bfd

LOG_STD_ACTION

-

6-Information

authentication packet received on sessions with invalid config

authentication only supported for multihop BFD sessions

bfd

LOG_STD_ACTION

-

6-Information

packet received failed authentication

packet authentication failed

bfd

LOG_STD_ACTION

-

6-Information

Could not allocate valid session handle

session handle not allocated

bfd

LOG_STD_ACTION

BFD-6-TIMERS_NOT_SUPPORTED

6-Information

BFD timer value Tx: [dec] and Rx: [dec] are not supported for software sessions

Timers not supported for software sessions

bfd

LOG_STD_ACTION

BFD-6-BFD_SESS_CREATED

6-Information

BFD-SYSLOG: bfd_session_created neigh [chars] proc:[chars] idb:[chars] handle:[dec] [chars]

bfd session created

bfd

LOG_STD_NO_ACTION

BFD-6-BFD_SESS_DESTROYED

6-Information

BFD-SYSLOG: bfd_session_destroyed [chars] neigh proc:[chars] handle:[dec] [chars]

bfd session destroyed

bfd

LOG_STD_NO_ACTION

BFD-6-BFD_IF_CONFIGURE

6-Information

BFD-SYSLOG: bfd config apply idb:[chars]

bfd config change

bfd

LOG_STD_NO_ACTION

BFD-6-BFD_SESS_GET_LD

6-Information

BFD-SYSLOG: bfd session get local discriminator [chars] neigh proc:[chars] handle:[dec] node: [chars]

Get bfd session local discriminator

bfd

LOG_STD_NO_ACTION

BFD-6-BFD_VRRPV3_SW_SESS_INVALID

6-Information

BFD-SYSLOG: ABORT: BFD session for VRRPv3 client on interface: [chars] NOT supported in software handle:[dec] adjacency: [chars] node: [chars]

bfd vrrpv3 sofware session offloading NOT supported

bfd

LOG_STD_NO_ACTION

BFD_DAMP-5-ZERODELAY

5-Notice

Dampening reuse timer is updated with 0 delay time

Inconsistency of dampening reuse timer wheel

bfd

LOG_STD_NO_ACTION

BFD_TEST-3-BAD_TYPE

3-Error

Invalid session type [dec]

invalid session type

bfd

LOG_STD_ACTION

BFD_TEST-3-BAD_ADDR_TYPE

3-Error

Invalid address type [dec]

invalid address type

bfd

LOG_STD_ACTION

BFD_TEST-3-WAVL_INSERT_FAIL_IPV6

3-Error

Failed inserting neighbor address %30P to wavl tree thread [dec]

wavl insert failed for ipv6.

bfd

LOG_STD_ACTION

BFD_TEST-3-WAVL_INSERT_FAIL_IPV4

3-Error

Failed inserting neighbor address %30i to wavl tree thread [dec]

wavl insert failed for ipv4.

bfd

LOG_STD_ACTION

BFD_TEST-3-WAVL_INSERT_FAIL_PW

3-Error

Failed inserting neighbor address %30i and vcid %lu to wavl tree thread [dec]

wavl insert failed for pw.

bfd

LOG_STD_ACTION

BFD_TEST-3-WAVL_WALK_FAIL

3-Error

wavl_walk failed while walking wavl tree thread [dec] interface [dec]

wavl walk of a thread failed.

bfd

LOG_STD_ACTION

BFD_TEST-3-WAVL_INIT_FAIL

3-Error

Failed initializing wavl tree.

wavl_init failed.

bfd

LOG_STD_ACTION

BFD_TEST-3-WAVL_TREE

3-Error

Failed to malloc space for wavl tree.

wavl tree malloc failed.

bfd

LOG_STD_ACTION

BFD_TEST-3-RESOURCE

3-Error

Cannot add BFD TEST as RF client. Return code [dec]

RF client id failed.

bfd

LOG_STD_ACTION

BFD_TEST-3-RF_INIT_FAIL

3-Error

Failed initializing Redundnacy Facility for BFD stub client.

stub RF init failed.

bfd

LOG_STD_ACTION

BFD_ISSU-2-INIT

2-Critical

BFD ISSU client initialization failed to [chars]. Error: [dec] [chars]

The BFD ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

bfd

LOG_STD_ACTION

BFD_ISSU-3-TRANSFORM_FAIL

3-Error

bfd ISSU client [chars] transform failed for message [dec]'. Error: [dec] [chars]

The BFD ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the BFD state between the active device and the standby device is not identical.

bfd

"show issu session <client_id> and " "show issu negotiated version <session_id>"

BFD_ISSU-2-GET_BUFFER

2-Critical

BFD ISSU client failed to get buffer for message. Error: [dec] [chars]

The BFD ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

bfd

"show logging and show checkpoint client"

BFD_ISSU-2-SEND_NEGO_FAILED

2-Critical

BFD ISSU client failed to send negotiation message. Error: [dec] [chars]

The BFD ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

bfd

"show logging and show checkpoint client"

BFD_ISSU-2-SESSION_NEGO

2-Critical

BFD ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The BFD ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

bfd

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

BFD_ISSU-2-SESSION_REGISTRY

2-Critical

BFD ISSU client failed to register session information. Error: [dec] [chars]

The BFD ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

bfd

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

BFD_ISSU-3-SESSION_UNREGISTRY

3-Error

BFD ISSU client failed to unregister session information. Error: [dec] [chars]

The BFD ISSU client failed to unregister session information.

bfd

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

BFD_ISSU-3-MSG_SIZE

3-Error

BFD ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The BFD ISSU client failed to calculate the MTU for the specified message. The BFD ISSU client is not able to send the message to the standby device.

bfd

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

BFD_ISSU-3-INVALID_SESSION

3-Error

BFD ISSU client does not have a valid registered session.

The BFD ISSU client does not have a valid registered session.

bfd

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

BFD_HA-2-RESOURCE

2-Critical

[chars]

System resource error occured

bfd

LOG_STD_ACTION

BFD_HA-2-CF

2-Critical

[chars][dec]

CF related error

bfd

LOG_STD_ACTION

BFD_HA-2-ET

2-Critical

[chars][dec]

Enhanced-timer error

bfd

LOG_STD_ACTION

VCMS-4-VCMS_CONNECTION

4-Warning

Client connection received for a Linecard [dec]-[dec] already connected

This linecard is already connected to another VCMS simulator

cmts-tools

" Disconnect the first Simulator before attempting" " a new connection"

VCMS-4-VCMS_CONNECTION_LOSS

4-Warning

Connection to simulator lost clearing interfaces for Slot [dec]-[dec]

The VCMS simulator has disconnected from the CMTS

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_INTERFACE_NOT_READY

4-Warning

Interface not ready

The VCMS simulator is trying to bring modems on an interface that is not up or ready.

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_LC_INBAND_CONNECTION

4-Warning

Linecard already connected via Inband Channel

The VCMS simulator is already connected to a linecard via Toaster Inband channel.

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_LC_FWD_AGT_CONNECTION

4-Warning

Linecard already connected to fwd agent

The VCMS simulator is already connected to a linecard via forwarding agent.

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-5-VCMS_CONNECTION_INIT

5-Notice

Simulator version [dec].[dec] from [inet] port [dec] interacting with interface [dec]

The VCMS simulator has started interacting with this interface

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_INVALID_SIZE

4-Warning

Invalid message size received from the simulator

The simulator sent a message with longer than expected packet size

cmts-tools

"Check the simulator code for possible issues"

VCMS-4-VCMS_INVALID_INTERFACE

4-Warning

Invalid interface Id received from the simulator

The simulator sent a message with interface ID

cmts-tools

"Check the simulator code for possible issues"

VCMS-4-CPE_RECORD_FAIL

4-Warning

Creation of CPE record failed

The proxy was unable to create CPE record due to possible memory failure

-

-

VCMS-5-VCMS_MAJOR_VER_MISMATCH

5-Notice

Error:VCMS connection attempt from client with major version [dec] but expected [dec]

The VCMS simulator major version mismatch

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-5-VCMS_MINOR_VER_MISMATCH

5-Notice

Warning:VCMS connection attempt from client with minor version [dec] but expected [dec]

The VCMS simulator mminor version mismatch

cmts-tools

"Check CMTS memory failures"

VCMS-4-MODEM_RECORD_FAIL

4-Warning

Creation of Modem record failed

The proxy was unable to create Modem record due to possible memory failure

cmts-tools

"Check CMTS memory failures"

VCMS-4-PAKPOOL_FAIL

4-Warning

Packet pool full

The VCMS pakpool was unable to allocate a packet

cmts-tools

"Check Proxy memory leaks"

BUFCAP-6-ENABLE

6-Information

Capture Point [chars] enabled.

Specified capture point has been enabled.

os

LOG_STD_NO_ACTION

BUFCAP-6-DISABLE

6-Information

Capture Point [chars] disabled.

Specified capture point has been disabled.

os

LOG_STD_NO_ACTION

BUFCAP-6-DISABLE_ASYNC

6-Information

Capture Point [chars] disabled. Reason : [chars]

Specified capture point has been disabled due to asynchronous event.

os

LOG_STD_NO_ACTION

BUFCAP-6-CREATE

6-Information

Capture Point [chars] created.

Specified capture point has been created.

os

LOG_STD_NO_ACTION

BUFCAP-6-DELETE

6-Information

Capture Point [chars] deleted.

Specified capture point has been deleted.

os

LOG_STD_NO_ACTION

BUFCAP-6-CAPPOINT_EXISTS

6-Information

Capture Point [chars] already exists.

A Capture point by the specified name already exists.

os

LOG_STD_NO_ACTION

BUFCAP-5-TIME_EXCEEDED

5-Notice

Capture Point [chars] disabled. The associated capture buffer's [chars]

The linear buffer does not have enough space left. Hence the packet was trimmed. This is the final element in the buffer.

os

LOG_STD_NO_ACTION

BUFCAP-5-BUFFER_FULL

5-Notice

Linear Buffer associated with capture buffer [chars] is full.

The linear buffer is full. Further capture would be halted.

os

LOG_STD_NO_ACTION

BUFCAP-5-MAX_ELEMS

5-Notice

Capture point [chars] disabled. The number of elements in associated capture buffer's [chars]

The buffer contains the maximum configured number of packets. The associated capture point will be disabled.

os

LOG_STD_NO_ACTION

BUFCAP-3-NO_MEM

3-Error

Not enough memory available for Buffer Capture Infrastructure

The buffer capture infrastructure could not get the memory it requested.

os

LOG_STD_REDUCE_ACTION

BUFCAP-3-INVALID_CAPPOINT

3-Error

Invalid capture point.

Some operation was attempted on a invalid capture point.

os

LOG_STD_ACTION

BUFCAP-3-ACTIVE_CAPPOINT

3-Error

Invalid operation was attempted on an active capture point [chars].

Invalid operation was attempted on an active \n\ capture point.

os

"Search for resolved software issues using the Bug Toolkit " "at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance copy the error message exactly as " "it appears on the console or in the system log enter the " "<CmdBold>show monitor capture point all<NoCmdBold> and " "<CmdBold>show tech<NoCmdBold> commands and contact your " "Cisco technical support representative providing the " "representative with the gathered information."

BUFCAP-3-INVALID_PARAM

3-Error

Invalid parameters

Invalid parameters were passed in to a buffer capture infrastructure function.

os

LOG_STD_ACTION

BUFCAP-3-EXPORT_BUFFER

3-Error

Error exporting buffer [chars] to location [chars]

The Buffer Capture Infrastructure is not able to export the buffer to the specified location

os

"Please check if a valid destination was specified. " "Or if a file by the same name already exists rename the dump file or " "remove the existing file from the destination location. " "If those actions do not resolve the problem " LOG_STD_ACTION

BUFCAP-6-RATE_LIMIT

6-Information

[dec] packets from capture point [chars] dropped due to rate limiting.

Rate limiting has been enabled and the number of packets exceed the allowed configured value.

os

-

BUFCAP-6-TOO_BIG

6-Information

The packet to be dumped is bigger than the buffer size of capture buffer [chars]. Packet of size [dec] dropped.

The packet is bigger than the configured/default buffer size.

os

"Change the parameters of the capture buffer. " "You can try to increase the size of the buffer " "or limit the number of bytes copied."

BUFCAP-3-NOSUCHCAPTURE

3-Error

Error finding capture point.

No such capture point exists

os

LOG_STD_ACTION

RADIX-3-NOMEMORY

3-Error

No memory available [chars]

The system is out of memory.

mem

"Try one of these actions to correct the problem:\n\\n\ Reduce the number of routes accepted by this router.\n\\n\ Upgrade hardware.\n\\n\ Use a smaller subset image on run-from-RAM platforms."

RADIX-3-DELETE

3-Error

Error deleting trie entry [chars]

A software programming error occurred.

Obtain from traceback decode

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

RADIX-3-ADDMASK

3-Error

Error adding mask entry [chars]

A software or hardware error occurred.

Obtain from traceback decode

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

RADIX-3-BADTREE

3-Error

Invalid pointer to head of tree 0x[hec]

A software programming error occurred.

Obtain from traceback decode

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

RADIX-4-ORPHAN

4-Warning

Orphaned mask [hex] refcount=[dec] at [hex] next=[hex]

A software error occurred.

Obtain from traceback decode

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

RADIX-2-INIT

2-Critical

No memory for radix initialization: [chars]

The system ran out of memory during initialization. This should only\n\ occur if an image is too large for the existing dynamic memory.

mem

"Use a smaller subset image or upgrade hardware."

INDXOBJ-3-INTERRUPT

3-Error

index object routine [chars] called from interrupt context

inappropriate index object routine called from interrupt routine.

-

LOG_STD_ACTION

INDXOBJ-3-ADD_ERROR

3-Error

index add for [chars] failed: [chars]

index object routine error

-

LOG_STD_ACTION

PRST_VBL-3-GENERAL

3-Error

Persistent general error: [chars]

Persistent variable general error

-

LOG_STD_ACTION

PRST_VBL-3-MEDIA

3-Error

Persistent media error: [chars]

Persistent variable error

-

LOG_STD_ACTION

SHMWIN-6-INVALID_ARGS

6-Information

One or more invalid arguments have been passed to the function [chars]

One or more invalid arguments have been passed to the shared memory api's

OS

"LOG_STD_ACTION "

SHMWIN-6-ALLOC_FAILURE

6-Information

Insufficient memory

There was a failure while returning physical memory to the system

OS

"LOG_STD_ACTION "

SHMWIN-3-FREE_FAILURE

3-Error

Failure while freeing memory in function [chars]

An attempt was made to free memory that has already been freed or is not within the address space of the current process

OS

"LOG_STD_ACTION "

SHMWIN-6-PTHREAD_MUTEX_LOCK_FAILED

6-Information

An internal mutex error has been encountered in function [chars]

A process which has obtained the access mutex has not released it as yet

OS

"LOG_STD_ACTION "

SHMWIN-6-PTHREAD_MUTEX_UNLOCK_FAILED

6-Information

An internal mutex error has been encountered in function [chars]

An internal mutex error has been enountered

OS

"LOG_STD_ACTION "

SHMWIN-6-SYS_LOCK_FAILED

6-Information

In function [chars] The process was unable to lock the shared memory against other processes

The process was unable to lock the shared memory against other users

OS

"LOG_STD_ACTION "

SHMWIN-6-SYS_UNLOCK_FAILED

6-Information

In function [chars] The process was unable to unlock the shared memory

The shared memory could not be unlocked due to an internal error

OS

"LOG_STD_ACTION "

SHMWIN-6-SYS_LOCK_CREATE_FAILED

6-Information

The lock creation for the shared memory failed in function [chars]

Lock creation for the shared memory failed

OS

"LOG_STD_ACTION "

SHMWIN-7-UNLINK_ERROR

7-Debug

An internal error occurred while unlinking in function [chars]

An internal error occurred while unlinking

OS

"LOG_STD_ACTION "

SHMWIN-6-SHMEM_FAILURE

6-Information

The function [chars] Could not access shared memory

Could not access shared memory

OS

"LOG_STD_ACTION"

SHMWIN-7-PHYS_MAP_FAILURE

7-Debug

In function [chars] Failed to map physical memory

Failed to map physical memory

OS

"LOG_STD_ACTION "

SHMWIN-6-INCONSISTENCY

6-Information

Inconsistent state in window

Inconsistent state in window

OS

"LOG_STD_ACTION"

SHMWIN-6-EXCEEDED_MAX_USERS

6-Information

In function [chars] The maximum number of users for a shared window has been exceeded

The maximum number of users for a shared window has been exceeded

OS

"LOG_STD_ACTION "

SHMWIN-6-VIRT_MAP_FAILURE

6-Information

In function [chars] Could not reserve virtual memory

Could not reserve virtual memory

OS

"LOG_STD_ACTION"

SHMWIN-6-MAX_WINDOWS_EXCEEDED

6-Information

In function [chars] process has exceeded the maximum number of windows that can be opened by it

Exceeded maximum number of windows that can be opened by a process

OS

"LOG_STD_ACTION"

SHMWIN-6-INVALID_PARAM

6-Information

An invalid parameter has been passed to the function [chars]

One or more invalid parameters have been passed to the shared memory api's

OS

"LOG_STD_ACTION"

SHMWIN-6-WINDOW_EXCEEDED_MAX_POOLS

6-Information

The maximum number of pools has been exceeded in function [chars]

The maximum number of pools has been exceeded

OS

"LOG_STD_ACTION"

SHMWIN-6-MEM_COLLISION

6-Information

In function [chars] the requested memory space collides with the memory space of other windows

Memory space collision

OS

"LOG_STD_ACTION"

SHMWIN-6-EXCEEDED_MAX_SIZE

6-Information

In function [chars] The requested memory size exceeded the window size

The memory requested in this window exceeded the window size

OS

"LOG_STD_ACTION"

SHMWIN-6-MUTEX_ERROR

6-Information

An internal mutex error has occured in the function [chars]

An error has been encountered in the locking or unlocking of the shared memory mutex

OS

"LOG_STD_ACTION"

SHMWIN-6-CORE_NOT_ENABLED

6-Information

In function [chars] The core has not been enabled to get more physical memory

The core has not been enabled

OS

"LOG_STD_ACTION"

SHMWIN-6-NOT_SUPPORTED

6-Information

The option passed to function [chars] is not supported

This option is not supported

OS

"LOG_STD_ACTION"

UTIL-3-RANGEINCON

3-Error

internal inconsistency [dec] [hec]

A fatal software error occurred.

os

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UTIL-3-RANGENULLINPUT

3-Error

null pointer input to range function

An attempt was made to access a range function with a NULL pointer.\n\ The range list creation failed.

-

"Review the error log for a corresponding malloc failed message. Copy\n\ the error message exactly as it appears and report it to your\n\ technical support representative."

UTIL-0-ITEMLIST_RESIZE

0-Emergency

An attempt was made to resize an itemlist but not enough memory is available

An attempt was made to resize itemlist memory to be larger than the memory available. Itemlists are often used when showing interface statistics. This event is unexpected and may be an indication of memory corruption.

-

"Note any recent commands that may have triggered this error. " "Copy the error message and traceback exactly as it appears " "and report it to your technical support representative."

UTIL-3-RADIXTREE

3-Error

Data structure error--[chars]

A software error occurred resulting in a data structure\n\ inconsistency.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. Ask for their assistance in obtaining\n\ a version of code with the error fixed."

UTIL-3-TREE

3-Error

Data structure error--[chars]

A software error occurred resulting in a data structure\n\ inconsistency.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. Ask for their assistance in obtaining\n\ a version of code with the error fixed."

UTIL-6-RANDOM

6-Information

A pseudo-random number was generated twice in succession

A pseudo-random number generator produced the same number twice\n\ in succession.

-

"Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative."

UTIL-3-IDTREE_TRACE

3-Error

[chars]

A software error occurred resulting in a data structure\n\ inconsistency.

xconnect

LOG_STD_ACTION

UTIL-3-IDTREE_NOTRACE

3-Error

[chars]

A software error occurred resulting in a data structure\n\ inconsistency.

xconnect

LOG_STD_ACTION

UTIL-3-DLL

3-Error

Data structure error -- [chars]

A software error occurred resulting in data structure inconsistency.

os

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SM-4-STOPPED

4-Warning

Event '[chars]' ignored because the state machine is stopped: [chars] [chars]

An attempted was made to post an event to a state machine that has\n\ already been stopped.

sm

LOG_STD_SH_TECH_ACTION

SM-4-BADEVENT

4-Warning

Event '[chars]' is invalid for the current state '[chars]': [chars] [chars]

An attempt was made to post an event to a state machine that is invalid \n\ for the current state.

sm

LOG_STD_SH_TECH_ACTION

SM-4-PERSIST

4-Warning

Persistent event '[chars]' did not leave the current state '[chars]': [chars] [chars]

An attempt was made to post a persistent event to a state machine that\n\ would cause an infinite loop in the current state.

sm

LOG_STD_SH_TECH_ACTION

SM-4-INIT

4-Warning

Internal error while initializing state machine '[chars]' state '[chars]': [chars]

An attempt was made to initialize an invalid state machine.

sm

LOG_STD_SH_TECH_ACTION

BIT-4-OUTOFRANGE

4-Warning

bit [dec] is not in the expected range of [dec] to [dec]

An invalid request was detected by the bitlist subsystem.

cosmos

LOG_STD_SH_TECH_ACTION

IDMGR-3-MALLOC_FAILURE

3-Error

[chars]

A malloc failure occured in ID Manager.

-

LOG_STD_ACTION

IDMGR-3-INTERRUPT

3-Error

[chars]

An id_get attempted at interrupt level.

-

LOG_STD_ACTION

IDMGR-3-INVALID_ID

3-Error

bad id in [chars] id: 0x%lX

An ID Manager error occurred.

-

LOG_STD_ACTION

IDMGR-3-INVALID_ID_TABLE_SIZE

3-Error

bad new ID table size

A bad new table request to ID Manager occurred.

-

LOG_STD_ACTION

IDMGR-3-ID_MANAGER_INTERNAL_ERROR

3-Error

[chars]

Internal Error occured with ID Manager.

os

LOG_STD_ACTION

IOS_LICENSE-2-NO_MEM

2-Critical

No memory available for [chars]

The Ios licensing subsystem could not obtain the memory it needed.

ios-licensing

"If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt."

IOS_LICENSE-2-NO_LICENSE

2-Critical

No valid license avaiable to run any feature

The Ios licensing subsystem could not get a valid license to run any feature on the box please purchase a license.

ios-licensing

"Purchase a valid license to run the features you requier on the " "box. You should contact the cisco portal or a TAC engineer to get " "a license. You can do a <CmdBold>show license<noCmdBold> at the " "privileged command line prompt to get the list of availabe feature " "in the box "

IOS_LICENSE-3-IPC_FAILED

3-Error

[chars] failed with an error = [chars]

The ipc calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE-3-UNKNOWN_MSG_TYPE

3-Error

an unknown message type was received dropping it msg_type = [dec]

Ios licensing subsystem received a msg type which it does not recognizes or support

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE-3-RTTYS_FAILED

3-Error

[chars] failed

The rttys calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE-3-FAILED

3-Error

[chars]

The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-3-FAILED

3-Error

[chars]

The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_EVENT

3-Error

[chars]

The ios image licensing subsystem received an event which it does not understand or recognizes

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_VERSION

3-Error

[chars]

The ios image licensing subsystem received an event for an unknown version of a feature

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-6-NO_LICENSE

6-Information

[chars] [chars].

There is no valid license available on the box and we are running on a default feature

ios-licensing

"please purchase a license to activate required features"

IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL

6-Information

Module name = [chars] Next reboot level = [chars] and License = [chars]

This is an informational message to display the change in the next reboot license level

ios-licensing

"This is an informational message no action is required"

IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL_CONFIG

6-Information

Please issue 'license boot' config command to make extension license [chars] available for use.

This is an informational message to info user that to make extension license available to support image level licensing image level needs to be configured

ios-licensing

"This is an informational message no action is required"

IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_CONFIG

6-Information

EULA must be accepted for license level = [chars]

This is an informational message to inform user that the user needs to reissue the command from an interactive terminal

ios-licensing

"This is an informational message no action is required"

LICENSE-1-ENFORCEMENT

1-Alert

Feature [chars] [chars] running without a License. UDI=[chars]

End User License Agreement was accepted on this device

none

"none"

LICENSE-2-NO_MEM

2-Critical

No memory available for [chars]

The IOS licensing subsystem could not obtain the memory it needed.

ios-licensing

"If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt."

LICENSE-2-VLS_ERROR

2-Critical

'[chars]' failed with an error - rc = [dec] - '[chars]'

The IOS licensing subsystem encountered an error with the VLS api

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service"

LICENSE-3-IMPLICIT_LIC

3-Error

[chars]

The IOS licensing subsystem encountered an error while initializing/handling the implicit licenses

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service"

LICENSE-2-LIC_STORAGE

2-Critical

[chars]

The IOS licensing subsystem does not have a primary storage

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service"

LICENSE-2-LIC_STORAGE_CORRUPT

2-Critical

[chars] UDI=[chars]

The IOS licensing subsystem detected corrupted storage

ios-licensing

"If this error message occurs please reinstall all the licenses." "If you do not have the licenses please contact Cisco with the correct" "UDI to get all the licenses issued for this particular device"

LICENSE-6-RECOVERED

6-Information

The IOS license storage on this device was recovered. UDI=[chars]

The IOS license storage on this device was recovered

ios-licensing

"none"

LICENSE-6-UNRECOVERABLE

6-Information

The IOS license storage on this device is being corrected. UDI=[chars]

The IOS license storage on this device is being corrected

ios-licensing

"If this message occurs please ignore."

LICENSE-3-LIC_PROCESS_CREATION_FAILED

3-Error

[chars]

The IOS licensing subsystem was unable to create a process

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-2-IPC_INIT

2-Critical

License IPC subsystem could not be initialized: [chars]

License IPC subsystem could not be initialized. The reason for failure is displayed after :

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-3-IPC_PORT

3-Error

License [chars] IPC port [chars] failed: [chars]

License IPC port could not be created. The reason for failure is displayed after :

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-3-SLAVE_REGISTER

3-Error

License Slave device registration failed : [chars]

License Slave registration failed. The reason for failure is displayed after :

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-1-EXPIRING

1-Alert

License for feature [chars] [chars] will expire in [chars]. UDI=[chars]

License for the feature specified will expire in the specified time.

ios-licensing

"If this message recurs customer should buy license for the feature" " from Cisco since feature will not run after license expiry"

LICENSE-1-EXPIRED

1-Alert

License for feature [chars] [chars] has expired [chars]. UDI=[chars]

License for the feature specified has expired

ios-licensing

"If this message recurs customer should buy the license from Cisco " "since feature will not run"

LICENSE-6-EULA_ACCEPT_ALL

6-Information

The Right to Use End User License Agreement is accepted

This message indicates that the customer has configured 'license agree end user agreement' in the system to indicate that EULA for all licenses are accepted. And that they accept the Right to use End Use License Agreement found at: http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html

ios-licensing

-

LICENSE-1-REQUEST_FAILED

1-Alert

License request for feature [chars] [chars] failed. UDI=[chars]

Your system is trying to run a feature without a license.

none

"Please buy and install the license for the feature immediately"

LICENSE-4-PRECEDENCE

4-Warning

Setting precedence for feature [chars] failed with error : [dec]

A license is revoked from the system

none

"This is just an informational message to" " log a message when a license has been revoked"

LICENSE-6-COUNT

6-Information

Feature [chars] [chars] license count changed from [dec] to [dec].

The feature's maximum licensable count has changed

none

"This is just an informational message to" "denote count change for particular feature"

LICENSE-6-VIOLATION

6-Information

Feature [chars] [chars] count violation - count = [dec] usage count = [dec].

The feature's count is less than the current usage count

none

"This is just an informational message to" "denote count change for particular feature"

LICENSE-4-UDI_MISMATCH

4-Warning

The source license udi[chars]:[chars] differs from the platform udi[chars]:[chars] please save the running config.

The source license udi mismatches with the platform udi

none

"Please save running-config."

LICENSE-4-LIC_AGENT_OFF

4-Warning

License Agent is turned off. UDI=[chars]

The License Agent on this device is not running

none

"Please check the device configuration " "if you need to enable it."

LICENSE-1-VALIDITY_ENDING

1-Alert

Feature [chars] [chars] will expire on [chars]. UDI=[chars]

-

-

-

LICENSE-1-VALIDITY_EXT_ENDING

1-Alert

Feature [chars] [chars] in grace period. UDI=[chars]

-

-

-

LICENSE-1-VALIDITY_ENDED

1-Alert

Feature [chars] [chars] [chars]. UDI=[chars]

-

-

-

LICENSE-3-IPC_ERROR

3-Error

[chars][chars] [hec] rc:[chars]

Licensing is experiencing errors when communicating to Line Cards using IPC

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_XMIT

3-Error

Client id:[dec] type = [dec] xmit failed error:[dec]

Licensing is experiencing errors when performing ISSU Transformation during a transmit operation

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_RCV

3-Error

Client id:[dec] type = [dec] receive failed error:[dec]

Licensing is experiencing Errors when performing ISSU Transformation during a receive operation

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_ERR

3-Error

[chars] error:[dec]

Licensing is experiencing ISSU Errors

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_MTU

3-Error

Client id:[dec] MTU failed error:[dec]

Licensing is experiencing Errors when performing ISSU GET MTU during a transmit operation

ios-licensing

"show issu nego"

LICENSE-3-SYNC_FAILED

3-Error

License command [chars] for feature [chars] [chars] failed on standby rc=[chars]

Licensing is experiencing Errors when performing incremental sync

ios-licensing

"show license"

LICENSE-3-BULK_SYNC_FAILED

3-Error

License bulk sync operation [chars] for feature [chars] [chars] failed on standby rc=[chars]

-

-

-

LICENSE-3-BULK_SYNC_INFO

3-Error

License bulk sync operation [chars] for feature [chars] [chars] Info on standby rc=[chars]

Licensing is experiencing Errors when performing bulk sync

ios-licensing

"show license"

LICENSE-3-FEATURE_INCONSISTENT

3-Error

License mismatch for feature [chars] [chars]: Active has [chars] and standby has [chars]

Licensing is experiencing Errors when performing consistency checker

ios-licensing

"show license"

LICENSE-2-UDI_CHANGED

2-Critical

UDI of this instance changed from OLD: [chars]:[chars] to New: [chars]:[chars]

License UDI has changed - caused mainly because of too many configuration changes.

ios-licensing

"show license udi history"

LICENSE-1-TRANSITION

1-Alert

EvalRightToUse License for feature [chars] [chars] will transition to RightToUse in [chars]. UDI=[chars]

License for the feature specified will transition in the numer of days displayed in the syslog message.

ios-licensing

"Customer is expected to purchase this license if" " usage is planned beyond the trial period which" " expires in the number of days displayed in the syslog message." " This license will automatically convert to a Right to Use at" " the end of the trial period"

LICENSE-1-TRANSITION_COMPLETE

1-Alert

RightToUse License for feature [chars] [chars] has become active. UDI=[chars]

The transition of the license from EvalRightToUse to Right to Use RTU is completed

ios-licensing

"The trial period for this license has ended. This" " trial license has been automatically converted to" " a Right to Use License. Customer is required to" " purchase this license to continue usage"

LIC_AGENT-3-MEMORY

3-Error

[chars]

License Agent subsystem has experienced a problem gettting the required\n\ memory to complete this operation.

lic_agent

"Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\ n\ upgrading the memory in the network device may be required."

LIC_AGENT-3-UNKNOWN_EVENT

3-Error

event [dec] [chars]

License Agent tried to execute an unknown event.

lic_agent

"Contact technical support for problem resolution."

REMOTE_TTY-2-NOMEM

2-Critical

Malloc failure for remote-tty [chars] data-structure

Unable to allocate memory for remote-tty data-structure.\n\ Remote-tty component will not be able to function properly.

remote-tty

"show memory summary"

SYS-2-RUNTIME_CAPABILITY_NOT_SET

2-Critical

Capability value [chars] needed by Feature [chars] is not defined.\n

An inconsistency was detected while looking up for capability on which feature functionality depends upon. It is software error because platform/branch using the feature should provide a override value for feature capability .

none

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-INVALID_FEATURE_INDEX

2-Critical

Feature index [dec] is not within the defined feature array boundary.

An inconsistency was detected while looking up for feature index. It is software error because of wrong enumeration of feature index.

none

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-INVALID_FEATURE_INDEX

2-Critical

-

-

-

-

SYS-2-INVALID_FEATURE_INDEX

2-Critical

-

-

-

-

SYS-2-INVALID_FEATURE_INDEX

2-Critical

-

-

-

-

DEAD-4-SCARLET

4-Warning

* Interface [chars]: I knew without asking she was into the blues

-

-

-

DEAD-4-SCARLET

4-Warning

-

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

SYS-5-LOGGING_STOP

5-Notice

Logging disabled - [chars] \n

Syslog logging has been disabled by the user from now on syslog message will not be received by the syslog servers or hosts will not be receiving the syslog messages

os-logging

LOG_STD_NO_ACTION

SYS-4-VRF_TABLE_INIT_WARNING

4-Warning

[chars]

The number of VRF's obtained from the platform is zero

os-logging

"If the registry is not populated for the subsystem " "is not in the image then the return value will be " "FALSE"

SYS-5-LOGGING_START

5-Notice

Logging enabled - [chars] \n

Syslog logging has been enabled by the user. From now on syslog messages will be delivered to all configured destinations.

os-logging

LOG_STD_NO_ACTION

SYS-5-LOG_CONFIG_CHANGE

5-Notice

[chars]

The user has changed the syslog logging configuration.

os-logging

LOG_STD_NO_ACTION

SYSLOGD-3-DROPPED_MESSAGES

3-Error

A total of %lu messages have been dropped by the syslog daemon due to [chars]\n

Either a large number of messages have been sent to syslogd before it has had the opportunity to process them in which case this most likely indicates a bug in the sending process. Or there was insufficient memory available in order to handle the message

syslog

LOG_STD_ACTION

SYS-3-LOGGINGHOST_FAIL

3-Error

Logging to host [chars] port [dec] failed \n

Logging syslog messages to specified server or host failed please check if the host is configured properly and reachable

os-logging

LOG_STD_NO_ACTION

SYS-3-LOGGINGHOST_CONNECTFAIL

3-Error

Unable to setup connection with host [chars] port [dec]

Unable to setup a connection with specified server or hostvrf check weather the syslog host is reachable

os-logging

LOG_STD_NO_ACTION

AUTOUPGRADE-6-RELOADED

6-Information

Successfully reloaded the new image: \[chars]\.

The device has succesfully been reloaded with the image downloaded previously by IOS Auto Upgrade Manager.

os

"This is an informational message only." " These messages may be disabled by changing the" " logging level."

AUTOUPGRADE-6-COMPLETE

6-Information

Auto Upgrade of the device completed. From: [chars] To: [chars].

The device has been upgraded with a new IOS image by IOS Auto Upgrade Manager

os

"This is an informational message only." " These messages may be disabled by changing the" " logging level."

AUTOUPGRADE-3-INVALIDCONFIG

3-Error

Upgraded image does not recognize [dec] lines of startup configuration

Either the saved startup configuration has invalid lines or the upgraded image is incompatible with the previous image

os

"Change/Delete the invalid lines from startup" " configuration or revert back to the previous" " image"

AUTOUPGRADE-3-NODISKSPACE

3-Error

Not enough free space in any filesystem. need [dec] bytes.

Auto Upgrade Manager won't be able to download the specified image because there is not enough free space in any filesystem.

os

"Use Auto Upgrade Manager disk cleanup utility" " to cleanup a filesystem. Use \"disk-management" " confirm\" or \"disk-management auto\" options with" " \"upgrade automatic getversion\" to use the" " disk cleanup utility. Otherwise you may cleanup" " a filesystem manually."

AUTOUPGRADE-3-DOWNLOADHASHFAIL

3-Error

Download hash verification fail

The image downloaded from cisco.com is corrupted. This usually points to a communication error.

os

"Retry \"upgrade automatic\". If the problem" " persists please check Bug Toolkit on the" " Cisco web-site for previously filed bugs and" " upgrade code if necessary. If you do not find" " a previously-filed bug collect the outputs of" " \"show logging\" \"show version\" and" " \"show running-config\" and open a TAC case with" " the gathered information."

AUTOUPGRADE-3-BADSIGNATURE

3-Error

Embedded signature verification failed.

The downloaded image is corrupted. This could be because of an invalid image name or a communication error.

os

"Make sure that the image name spcified refers to" " a valid IOS image and retry \"upgrade automatic\"." " If the problem" " persists please check Bug Toolkit on the" " Cisco web-site for previously filed bugs and" " upgrade code if necessary. If you do not find" " a previously-filed bug collect the outputs of" " \"show logging\" \"show version\" and" " \"show running-config\" and open a TAC case with" " the gathered information."

AUTOUPGRADE-3-NVSAVEFAIL

3-Error

Failed to save in nvram

Auto upgrade manager encountered a problem while attempting to save information to NVRAM.

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the outputs of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-RELOADFAILED

3-Error

Failed to reload the device with the new image.

Auto upgrade manager could not reload the device with the new image. A common reason is insufficient RAM space.

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-IDAEXCEPTION

3-Error

Exception occurred: [chars]. Error retrieving image info from cisco.com.

Auto upgrade manager could not obtain information about the new image from cisco.com.

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-STARTUPPROCFAIL

3-Error

Failed to create the auto upgrade startup process.

A software error has occurred.

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-HTTPSENDFAIL

3-Error

HTTP send failed: [chars]

A software error has occurred.

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-NODOWNLOADFS

3-Error

Auto Upgrade Manager cannot download new image in the filesystem where current image is running

Not enough free space in any filesystem for the new image

os

"Use Auto Upgrade Manager disk cleanup utility" " to cleanup a filesystem. Use \"disk-management" " confirm\" or \"disk-management auto\" options with" " \"upgrade automatic getversion\" to use the" " disk cleanup utility. Otherwise you may cleanup" " a filesystem manually."

AUTOUPGRADE-6-DELETEDPREVIOUS

6-Information

Auto Upgrade Manager deleted the previous image [chars]

The previous image has been deleted so that there is enough free space to download the new image.

os

"This is an informational message only." " These messages may be disabled by changing the" " logging level."

AUTOUPGRADE-3-DELETEFAIL

3-Error

Auto Upgrade Manager failed to delete the previous image [chars]

Auto Upgrade Manager attempted to delete the previous image to make enough free space for the new image in the filesystem. However an error occurred while deleting the previous image

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-SQUEEZEFAIL

3-Error

Auto Upgrade Manager failed to squeeze the filesystem [chars]

A software error has occurred

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-DOWNLOADFAIL

3-Error

Auto Upgrade Manager is unable to download new image from [chars]

Possible reasons of this failure include: 1. temporary communication problem 2. server unavailable 3. incorrect username/password 4. the image may not exist in the location 5. there is not enough space in filesystem

os

"Please ensure that there is enough free space in " " a filesystem and image path username password" " information are correct. Then retry the download" " using \"upgrade automatic getversion\"." " If the new image still fails to download" " please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

AUTOUPGRADE-3-NULLQ

3-Error

NULL queue pointer

A software error has occurred.

os

"Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images"

EVENT_TRACE-6-ENABLE

6-Information

Trace already enabled.

Specified event trace has already been enabled

Trace

LOG_STD_DBG_ACTION

EVENT_TRACE-3-SIZE_ELEM

3-Error

Size of trace element = [dec] is greater than size = [dec] allowed

The size of the specified individual trace entry is greater than the allowed size.

Trace

"Reduce the individual trace entry size so as not " "to exceed the max while initializing the event trace"

EVENT_TRACE-3-NUM_ELEM

3-Error

Number of trace element = [dec] is greater than number = [dec] allowed

The number of trace entries exceed the allowed amount

Trace

"Reduce the number of trace entries"

EVENT_TRACE-3-NO_MEM

3-Error

Not enough memory for [dec] trace elements.

The system memory is insufficient for the number of trace elements specified.

Trace

"Reduce the size of the event trace"

EVENT_TRACE-3-NO_FILENAME

3-Error

Dump file not specified.

No filename has been specified as output for the event trace.

Trace

"You must specify the trace dump filename. To specify the trace dump " "filename enter the monitor event-trace comp dump-file filename command " "in global configuration mode"

EVENT_TRACE-3-SIZE_FILENAME

3-Error

Trace filename size = [dec] greater than size = [dec] allowed

The length of the specified Event Trace filename exceeds the allowed.

Trace

"Shorten the filename."

EVENT_TRACE-3-OPEN_FILE

3-Error

Couldn't open [chars]...

The Event Trace subsystem could not open a file for the specified event trace dump.

Trace

"If a file by the same name already exists rename the dump file or " "remove the existing file from the file system."

EVENT_TRACE-3-WRITE_FILE

3-Error

Error writing to file [chars]

Event trace is not able to write to the specified filesystem

Trace

"The filesystem might not be available. Try " "changing the destination filesystem and dumping there. " "If none work copy the error message exactly as it and " "call your Cisco technical support representative"

EVENT_TRACE-3-CLOSE_FILE

3-Error

Error closing file [chars]

The Event Trace subsystem can not close the specified file

Trace

"No action required. This will not affect " "system functionality"

EVENT_TRACE-6-NO_FORMATTER

6-Information

[chars]: no formatter provided binary dumping.

No formatter function was provided during the initialization of the specified event trace.

Trace

LOG_STD_NO_ACTION

EVENT_TRACE-3-RESIZE

3-Error

Enable trace before resizing

The specified event trace must be enabled before resizing occurs.

Trace

"Enable the specified event trace."

EVENT_TRACE-3-OPEN

3-Error

[chars]: Trace failed to open

Initialization of the specified event trace has failed.

Trace

LOG_STD_ACTION

EVENT_TRACE-3-CONTINUOUS

3-Error

Enable trace before setting continuous display

The specified event trace must be enabled before continuous display could occurs.

Trace

"Enable the specified event trace."

EVENT_TRACE-3-NO_TRACE_NAME

3-Error

Invalid trace name [chars]

There is no trace buffer configured by the name entered.

Trace

"Check whether there is an event trace buffer " "configured by the name entered and then enter the correct trace " "buffer name."

EVENT_TRACE-3-GROUP_ID

3-Error

Duplicate registration of group-id [dec]

Software subsystem is trying to register a group id for event trace which has already been used by another subsystem.

Trace

LOG_STD_ACTION

DBMS-3- API

3-Error

[chars]

The specified operation in the api component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- DATABASE

3-Error

[chars]

The specified operation in the database component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- TABLE

3-Error

[chars]

The specified operation in the table component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- KEY

3-Error

[chars]

The specified operation in the key component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- ENGINE

3-Error

[chars]

The specified operation in the engine component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- SNAPSHOT

3-Error

[chars]

The specified operation in the snapshot component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- REPLICATION

3-Error

[chars]

The specified operation in the replication component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- SHADOW

3-Error

[chars]

The specified operation in the shadow component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- CONNECTION

3-Error

[chars]

The specified operation in the connection component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- MESSAGE

3-Error

[chars]

The specified operation in the message component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- BUNDLE

3-Error

[chars]

The specified operation in the bundle component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

DBMS-3- PORT

3-Error

[chars]

The specified operation in the port component failed.

cmts-platform-infr

LOG_STD_NO_ACTION

VFI-4-CONFIG

4-Warning

[chars]

Invalid VFI configuration data passed.

vpls

LOG_STD_NO_ACTION

VFI-3-ILLEGAL

3-Error

[chars]

An illegal event has been processed by the xconnect subsystem.

vpls

LOG_STD_NO_ACTION

VFI-6-VFI_STATUS_CHANGED

6-Information

Status of VFI [chars] changed from [chars] to [chars]

VFI status has changed

vpls

LOG_STD_NO_ACTION

ATOM_TRANS-3-CONSISTENCY

3-Error

[chars]

An action attempted by the layer 2 transport over MPLS implementation encountered an unexpected condition

xconnect

LOG_STD_ACTION

ATOM_TRANS-4-CONFIG

4-Warning

[chars]

AToM pseudowire uses undesirable configuration.

xconnect

LOG_STD_ACTION

ATOM_TRANS-5-IMPOSITION_DISABLED

5-Notice

[chars]

Imposition disabled specified AToM VC.

xconnect

LOG_STD_NO_ACTION

ATOM_TRANS-5-IMPOSITION_ENABLED

5-Notice

[chars]

Imposition enabled for specified AToM VC.

xconnect

LOG_STD_NO_ACTION

ATOM_TRANS-5-DISPOSITION_ENABLED

5-Notice

[chars]

Disposition enabled for specified AToM VC.

xconnect

LOG_STD_NO_ACTION

ATOM_TRANS-5-DISPOSITION_DISABLED

5-Notice

[chars]

Disposition disabled for specified AToM VC.

xconnect

LOG_STD_NO_ACTION

ATOM_TRANS-3-LABEL_ALLOC_FAIL

3-Error

Failed to allocate local label for peer:[inet] vcid:[dec]

Failed to allocate local label for specified AToM VC.

xconnect

LOG_STD_ACTION

ATOM_TRANS-3-INIT_FAIL

3-Error

Failed to start AToM Manager

Failed to start and initialize AToM Manager.

xconnect

LOG_STD_ACTION

ATOM_TRANS-4-PW_MAX_REACHED

4-Warning

[chars]

Pseudowire maximum limit reached for the L2 subscriber author group

xconnect

LOG_STD_ACTION

ATOM_TRANS-5-PW_WATERMARK_LIMIT

5-Notice

[chars]

Pseudowire max watermark limit reached for the L2 subscriber author group

xconnect

LOG_STD_ACTION

ATOM_TRANS-3-XDM_CREATE

3-Error

Failed to create XDM - rc [dec]

ATOM Manager was unable to create a Dispatch Manager instance for event handling.

xconnect

LOG_STD_ACTION

ATOM_TRANS-6-ATOM_NO_ROUTER_ID

6-Information

[chars]

No router ID is available for AToM to use and this will impact pseudowire VCCV. Please enable \l2 router-id <address>\ or enable an LDP router ID if you wish VCCV to be operational.

xconnect

LOG_STD_ACTION

ATOM_HA-3-UPDATE

3-Error

[chars]

AToM Manager High Availability update failed.

xconnect

LOG_STD_ACTION

ATOM_HA-3-RECOVERY

3-Error

[chars]

AToM Manager High Availability recovery failed.

xconnect

LOG_STD_ACTION

XCONNECT-3-ILLEGAL

3-Error

[chars]

An illegal event has been processed by the xconnect subsystem.

xconnect

LOG_STD_NO_ACTION

XCONNECT-3-CONFIG

3-Error

[chars]

An invalid xconnect configuration or an error in processing xconnect configuration has occurred.

xconnect

LOG_STD_NO_ACTION

XCONNECT-5-REDUNDANCY

5-Notice

[chars]

An event has occurred that has caused the xconnect redundancy facility to generate a switchover event to the specified backup member

xconnect

LOG_STD_NO_ACTION

XCONNECT-5-PW_STATUS

5-Notice

[chars]

An event has occurred that has caused the pseudowire to change status

xconnect

LOG_STD_NO_ACTION

XCONNECT-5-PW_STATUS_LOST

5-Notice

[chars]

The system is dropping PW_STATUS messages because the status queue is full

xconnect

LOG_STD_NO_ACTION

XCONNECT-4-VC_TYPE_INCOMPATIBLE

4-Warning

The 'vc type' command on pseudowire [chars]:[dec] is incompatible with xconnect [chars] ignored

The 'vc type' command is only intended to be used with VPLS. Use the 'interworking' command on xconnects in order to specify the type of VC for VPWS.

xconnect

"Unconfigure the 'vc type' command from the " "pseudowire interface or template and configure" "'interworking' on the xconnect."

AC-3-AC_WS_REGISTER

3-Error

L2VPN WS registration failed for [chars]

An error was encountered when attempting to register the specified Attachment Circuit type with the Layer 2 Virtual Private Network Wire Service facility.

ac

LOG_STD_ACTION

AC-3-AC_SANITY

3-Error

[chars]

A unexpected sanity check failed during Attachment Circuit processing.

ac

LOG_STD_ACTION

AC-3-L2SS_NULL_CONTEXT

3-Error

Encountered a NULL context in [chars]

Encountered a NULL context in L2SS Manager.

ac

LOG_STD_ACTION

AC-3-L2SS_WRONG_KEYS

3-Error

Wrong set of keys in [chars] message

SIP sends a wrong set of keys to L2SS Manager.

ac

LOG_STD_ACTION

AC-3-L2SS_UNEXPECTED

3-Error

Received unexpected [chars] message

L2SS received unexpected message.

ac

LOG_STD_ACTION

AC-3-L2SS_BAD_HANDLE

3-Error

Corrupted L2SS handle [[hec]].

An internal L2SS Manager occurred.

ac

LOG_STD_ACTION

AC-3-ACMGR_XDM_CREATE

3-Error

Failed to create XDM - rc [dec]

Attachment Circuit Manager was unable to create a Dispatch Manager instance for event handling.

ac

LOG_STD_ACTION

AC-3-ACMGR_INVALID_MSG

3-Error

Received [chars]

Attachment Circuit Manager receives invalid message.

ac

LOG_STD_ACTION

AC-3-ACMGR_MISSED_CIRCUIT

3-Error

Circuit info missing in [chars] message.

AC Manager received message with missing circuit info

ac

LOG_STD_ACTION

AC-3-ACMGR_INVALID_HDL

3-Error

Received invalid [chars] handle

Attachment Circuit Manager receives invalid handle.

ac

LOG_STD_ACTION

EVPN-5-VC_STATUS

5-Notice

EVPN[[dec] [dec]/[dec]]: VC state [chars]

An event has occurred that has caused the vc to change status

evpn-mgr

LOG_STD_NO_ACTION

EVPN-5-PEER_STATUS

5-Notice

Peer [chars] [chars] is [chars]

An event has occurred that has caused the peer to change status

evpn-mgr

LOG_STD_NO_ACTION

EVPN-3-DUP_MAC

3-Error

Duplicate [chars]MAC address [enet] EVI [dec] [chars] [dec] detected on [chars] and [chars]

EVPN has detected a duplicate MAC address in the network. This occurs when the same MAC address is learned from both a local port and a remote device more than N times within M seconds where N is the configured MAC duplication limit which defaults to 5 and M is the configured MAC

evpn-mgr

"Locate and remove the duplicate MAC address then use the command " "'clear l2vpn evpn mac duplicate <bridge domain ID> <MAC address>' to " "resume MAC learning for that address."

EVPN-3-DUP_IP

3-Error

Duplicate IP address [chars] EVI [dec] [chars] [dec] detected on [chars] and [chars]

EVPN has detected a duplicate IP address in the network. This occurs when the same IP address is learned from multiple different MAC addresses more than N times within M seconds where N is the configured IP duplication limit which defaults to 5 and M is the configured IP

evpn-mgr

"Locate and remove the duplicate IP address then use the command " "'clear l2vpn evpn ip duplicate <bridge domain ID> <IP address>' to " "resume IP learning for that address."

EVPN-5-DUP_CLEAR_MAC

5-Notice

Cleared duplicate MAC address [enet] EVI [dec] [chars] [dec]

EVPN has cleared the duplicate condition on a MAC address that was previously detected as a duplicate.

evpn-mgr

LOG_STD_NO_ACTION

EVPN-5-DUP_CLEAR_IP

5-Notice

Cleared duplicate IP address [chars] EVI [dec] [chars] [dec]

EVPN has cleared the duplicate condition on a IP address that was previously detected as a duplicate.

evpn-mgr

LOG_STD_NO_ACTION

EVPN-3-CORE_ISOLATION

3-Error

Bringing down multi-homing access interface [chars]

EVPN is bringing down the multi-homing access interface due to core isolation failure detected.

evpn-mgr

"Diagnose and recover from core isolation failure then EVPN will bring " "the multi-homing access interface up automatically."

EVPN-5-CORE_CONNECTED

5-Notice

Bringing up multi-homing access interface [chars]

EVPN has recovered from a core isolation failure and is bringing up the multi-homing access interface.

evpn-mgr

LOG_STD_NO_ACTION

EVPN-3-INTERNAL

3-Error

Internal error: [chars]

An internal software error has occurred.

evpn-mgr

LOG_STD_ACTION

EVPN-3-MISSING_MCAST_GROUP

3-Error

Missing multicast group configuration for L2 VNI [dec]

A Layer 2 VNI used for EVPN must have an associated multicast group for Broadcast Unknown Unicast and Multicast traffic when static replication is configured.

evpn-mgr

"Correct the configuration by adding the " "mcast-group keyword to the 'member vni' command " "in the NVE interface sub-mode."

EVPN-3-INCOMPATIBLE_MCAST_GROUP

3-Error

Incompatible multicast group configuration for L2 VNI [dec]

A Layer 2 VNI used for EVPN must have not an associated multicast group for Broadcast Unknown Unicast and Multicast traffic when ingress replication is configured.

evpn-mgr

"Correct the configuration by removing the " "mcast-group keyword from the 'member vni' command " "in the NVE interface sub-mode."

EVPN-3-INCOMPATIBLE_REPLICATION

3-Error

Incompatible replication configuration for EVI [dec] [chars] [dec]

An EVPN instance with MPLS encapsulation must not be configured if the replication type is static.

evpn-mgr

"Correct the configuration by changing the " "replication type configuration to ingress."

EVPN-3-UNSUPPORTED_MIX_ENCAP

3-Error

EVIs with different encapsulation types are not supported in the same Ethernet Segment[[chars]]

All EVPN instances associated with an Ethernet Segment must have the same encapsulation type.

evpn-mgr

"Correct the configuration by changing the encapsulation type of the " "EVPN instances associated with the Ethernet Segment to be the same."

EVPN-3-ES_ENCAP_MISMATCH

3-Error

ES route with encapsulation mismatch received from [chars]/[chars]

Local and remote EVPN instances must have the same encapsulation type.

evpn-mgr

"Correct the configuration by changing the encapsulation type of local " "or remote EVPN instance"

EVPN-3-MAX_PEERS_EXCEEDED

3-Error

Maximum number of peers [dec] exceeded for Ethernet Segment [chars] in

EVPN has received a peer nexthop update from BGP which would push the number of peers in the Ethernet Segment past the supported limit for single-active redundancy mode. The newly discovered peer will not be added to the peer list so as not to impact current peering and designated forwarder election results.

evpn-mgr

"Take one of the PE's out of the Ethernet Segment by modifying or " "removing its ESI configuration. If it's a PE already peering need to " "toggle the access interface or reconfigure ESI on the newly discovered " "peer to ensure it is re-advertised."

EVPN-3-MAX_PEERS_EXCEEDED_ES_DISABLED

3-Error

Maximum number of peers [dec] exceeded for Ethernet Segment [chars] in

EVPN has received a peer nexthop update from BGP which would push the number of peers in the Ethernet Segment past the supported limit for single-active redundancy mode. The Ethernet Segment will be disabled.

evpn-mgr

"Take one of the PE's out of the Ethernet Segment by modifying or " "removing its ESI configuration. If it's a PE already peering need to " "toggle the access interface or reconfigure ESI on the newly discovered " "peer to ensure it is re-advertised."

EVPN-5-ES_LOCAL_RED_MOD_CHANGE_NOT_ALLOWED

5-Notice

Local redundancy mode change is not allowed for Ethernet Segment [chars] because it has two or more forwarders.

Local redundancy mode change is not allowed for Ethernet Segments with two or more forwarders. Configuration is updated while local redundancy mode is kept unchanged. Local redundancy mode will be updated when the number of forwarders drops to less than two.

evpn-mgr

"Reduce the number of forwarders to less than two to allow local " "redundancy mode change."

EVPN-5-ES_LOCAL_RED_MOD_CHANGED

5-Notice

Local redundancy mode has been changed to [chars] for Ethernet Segment [chars].

An event has occurred that has caused local redundancy mode to change.

evpn-mgr

LOG_STD_NO_ACTION

CONFIG-3-VFI

3-Error

ERRMSG_NOFLAGS

-

-

-

ILLEGAL-3-VFI

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

VFI_STATUS_CHANGED-5-VFI

5-Notice

ERRMSG_NOFLAGS

-

-

-

VFI_REDUNDANCY_STATUS_CHANGED-5-VFI

5-Notice

ERRMSG_NOFLAGS

-

-

-

XDM_CREATE-3-VFI

3-Error

ERRMSG_NOFLAGS

-

-

-

CONSISTENCY-3-ATOM_TRANS

3-Error

ERRMSG_NOFLAGS

-

-

-

CONFIG-4-ATOM_TRANS

4-Warning

ERRMSG_NOFLAGS

-

-

-

IMPOSITION_DISABLED-5-ATOM_TRANS

5-Notice

ERRMSG_NOFLAGS

-

-

-

IMPOSITION_ENABLED-5-ATOM_TRANS

5-Notice

ERRMSG_NOFLAGS

-

-

-

DISPOSITION_ENABLED-5-ATOM_TRANS

5-Notice

ERRMSG_NOFLAGS

-

-

-

DISPOSITION_DISABLED-5-ATOM_TRANS

5-Notice

ERRMSG_NOFLAGS

-

-

-

LABEL_ALLOC_FAIL-3-ATOM_TRANS

3-Error

ERRMSG_NOFLAGS

-

-

-

INIT_FAIL-3-ATOM_TRANS

3-Error

ERRMSG_NOFLAGS

-

-

-

XDM_CREATE-3-ATOM_TRANS

3-Error

ERRMSG_NOFLAGS

-

-

-

UPDATE-3-ATOM_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

RECOVERY-3-ATOM_HA

3-Error

ERRMSG_NOFLAGS

-

-

-

ILLEGAL-3-XCONNECT

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

CONFIG-3-XCONNECT

3-Error

ERRMSG_FLAG_TRACEBACK

-

-

-

REDUNDANCY-5-XCONNECT

5-Notice

ERRMSG_NOFLAGS

-

-

-

PW_STATUS-5-XCONNECT

5-Notice

ERRMSG_NOFLAGS

-

-

-

PW_STATUS_LOST-5-XCONNECT

5-Notice

ERRMSG_NOFLAGS

-

-

-

L2VPN_GLOBAL_OP-5-XCONNECT

5-Notice

ERRMSG_NOFLAGS

-

-

-

XDM_CREATE-3-XCONNECT

3-Error

ERRMSG_NOFLAGS

-

-

-

API_FAILED-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

SHUTDOWN-6-L2VPN

6-Information

ERRMSG_NOFLAGS

-

-

-

SHUTDOWN_REQUEST_FAILED-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_BIND-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_DROP-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_REG-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_RECV-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_SEND-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

MTS_Q-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

PTHREAD_CREATE-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

INVALID_MSG-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

PPM_REQ_FAILED-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

IF_SET_CFG_RESP_FAILED-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

IF_PW_LIMIT_EXCEEDED-5-L2VPN

5-Notice

ERRMSG_NOFLAGS

-

-

-

IF_MULTIPLE_SVC_ASSOC-4-L2VPN

4-Warning

ERRMSG_NOFLAGS

-

-

-

IF_L3_SVC_ASSOC-4-L2VPN

4-Warning

ERRMSG_NOFLAGS

-

-

-

SEQNO_SYNC_FAILED-3-L2VPN

3-Error

ERRMSG_NOFLAGS

-

-

-

EAP-2-PROCESS_ERR

2-Critical

[chars]

This is critical condition where the router could not perform EAP\n\ process related operation.

eap

"Reload the device."

EAP-6-MPPE_KEY

6-Information

IP=[chars]| MPPE_RECV_KEY_LENGTH=[dec]

This messages informs that the router received MPPE KEY for the specified\n\ host.

eap

"No action is required."

EAP-4-BADPKT

4-Warning

IP=[inet]| HOST=[chars]

This messages informs that the router received an invalid or malformed\n\ EAP packet from the specified host.

eap

"Check specified host for EAP operation."

msg_ACCESS_SESSION-3-TRACE_INIT_FAIL

3-Error

Initialization failed with code: [dec]

Failed to initialize access-session trace.

dot1x-ios

LOG_STD_NO_ACTION

msg_ACCESS_SESSION-3-TRACE_REG_FAIL

3-Error

Component [chars] registration failed. Error code: [dec]

Component failed to register with access-session trace

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-START

5-Notice

Starting '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars]

Starting an authentication method

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-SUCCESS

5-Notice

Authorization succeeded for client [enet] on Interface [chars]

Authorization was successful.

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-FAIL

5-Notice

Authorization failed or unapplied for client [enet] on Interface [chars]

Authorization was unsuccessful.

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-VLANASSIGN

5-Notice

VLAN [dec] assigned to Interface [chars] AuditSessionID [chars]

VLAN assignment

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-SECURITY_VIOLATION

5-Notice

Security violation on the interface [chars] new MAC address [enet] is seen.

A host on the specified interface is attempting to gain access into the network or is trying to authenticate in a host mode that does not support the number of hosts attached. This is treated as a security violation and the port has been error-disabled.

dot1x-ios

"Ensure that the port is configured to support the " "number of hosts attached. Enter the " "<cmdbold>shutdown<nocmdbold> command followed by " "<cmdbold>no shutdown<nocmdbold> command to restart " "the port."

AUTHMGR-7-FAILOVER

7-Debug

Failing over from '[chars]' for client [chars] on Interface [chars]

Failing over from the current authentication method

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-7-STOPPING

7-Debug

Stopping '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars]

Stopping the current authentication method

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-7-NOMOREMETHODS

7-Debug

Exhausted all authentication methods for client [chars] on Interface [chars]

All available authentication methods have been tried

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-MACMOVE

5-Notice

MAC address [enet] moved from Interface [chars] to Interface [chars]

Client has moved to a new interface without logging off on the previous one.

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-5-MACREPLACE

5-Notice

MAC address [enet] on Interface [chars] is replaced by MAC [enet]

A new client has triggered a violation causing an existing client to be replaced

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-4-UNAUTH_MOVE

4-Warning

[chars] MAC address [enet] from [chars] to [chars]

Move while not authenticated on old IDB

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-4-ILLEGAL_TRACE_REQ

4-Warning

Component ID [dec] not registered.

Attempt to log a message with unregistered ID.

dot1x-ios

LOG_STD_NO_ACTION

AUTHMGR-0-CONFIG_CORRUPT

0-Emergency

Checksummed interface configuration corruption detected.

Interface configuration field was modified unexpectedly.

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_INIT_FAIL

3-Error

Initialization failed with code: [dec]

Failed to initialize access-session trace.

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_REG_FAIL

3-Error

Component [chars] registration failed. Error code: [dec]

Component failed to register with access-session trace

dot1x-ios

LOG_STD_NO_ACTION

MAB-5-SUCCESS

5-Notice

Authentication successful for client [chars] on Interface [chars]

Authentication was successful.

-

LOG_STD_NO_ACTION

MAB-5-FAIL

5-Notice

Authentication failed for client [chars] on Interface [chars]

Authentication was unsuccessful.

-

LOG_STD_NO_ACTION

DOT1X-5-SUCCESS

5-Notice

Authentication successful for client [chars] on Interface [chars]

Authentication was successful.

-

LOG_STD_NO_ACTION

DOT1X-5-FAIL

5-Notice

Authentication failed for client [chars] on Interface [chars]

Authentication was unsuccessful.

-

LOG_STD_NO_ACTION

DOT1X-5-RESULT_OVERRIDE

5-Notice

Authentication result overridden for client [chars] on Interface [chars]

Authentication result was overridden

-

LOG_STD_NO_ACTION

DOT1X-4-PROC_START_ERR

4-Warning

Dot1x unable to start.

The system failed to create the Dot1x process.

-

"Restart Dot1x process by entering <cmd>dot1x " "system-auth-control<cmd> command. If this message " "recurs Reload the device."

DOT1X-4-UNKN_ERR

4-Warning

An unknown operational error occurred.

The Dot1x process cannot operate due to an internal system error.

-

"Reload the device"

DOT1X-4-MEM_UNAVAIL

4-Warning

Memory was not available to perform the 802.1X action. AuditSessionID [chars]

Insufficient system memory is available to perform the Dot1x Authentication.

-

"Reduce other system activity to ease memory " "demands. If conditions warrant upgrade to " "a larger memory configuration."

DOT1X-6-INFO_EAPOL_PING_RESPONSE

6-Information

The interface [chars] has an 802.1x capable client with MAC [enet]

An EAPOL ping was sent out on this port to determine 802.1x readiness of the client attached. An EAPOL response has been received by the device such as a PC.

802.1x

"No action required."

DOT1X-5-IGNORE_LARGER_EAPOL

5-Notice

EAPOL packet size[dec] to be sent is larger than MTU

Targetted EAPOL packet size is larger than mtu size of the port on which client is connected and hence ignoring the packet to be sent out

802.1x

"Configure AAA server to fragement eap-method" " data so that EAPOL size is smaller than interface MTU size"

EPM-6-ACL_CONFIG_ERROR

6-Information

ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]'

This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration

pem

"Change ACE configuration for the specifed ACL"

EPM-6-AUTH_ACL

6-Information

POLICY [chars]| EVENT [chars]

This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed

pem

"No action required"

EPM-3-SEND_MSG_FAILURE

3-Error

Process send msg failure for session hdl [hec] [chars]

This message indicates a process send msg failure

eedge-epm

"No action required"

MSP_ISSU-2-INIT

2-Critical

MSP ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MSP ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

msi-proxy

LOG_STD_ACTION

MSP_ISSU-3-TRANSFORM_FAIL

3-Error

MSP ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MSP ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MSP state between the active device and the standby device is not identical.

msi-proxy

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MSP_ISSU-3-MSG_NOT_OK

3-Error

MSP ISSU client 'Message Type [dec]' is not compatible

The MSP ISSU client received an incompatible message from the peer device. The message cannot be processed.

msi-proxy

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MSP_ISSU-3-MSG_SIZE

3-Error

MSP ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MSP ISSU client failed to calculate the MTU for the specified message. The MSP ISSU client is not able to send the message to the standby device.

msi-proxy

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MSP_ISSU-3-INVALID_SESSION

3-Error

MSP ISSU client does not have a valid registered session.

The MSP ISSU client does not have a valid registered session.

msi-proxy

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MSP_ISSU-2-SESSION_REGISTRY

2-Critical

MSP ISSU client failed to register session information. Error: [dec] [chars]

The MSP ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

msi-proxy

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MSP_ISSU-3-SESSION_UNREGISTRY

3-Error

MSP ISSU client failed to unregister session information. Error: [dec] [chars]

The MSP ISSU client failed to unregister session information.

msi-proxy

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MSP_ISSU-2-SESSION_NEGO

2-Critical

MSP ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MSP ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

msi-proxy

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MSP_ISSU-2-SEND_NEGO_FAILED

2-Critical

MSP ISSU client failed to send negotiation message. Error: [dec] [chars]

The MSP ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

msi-proxy

"show logging and show checkpoint client"

MSP_ISSU-2-GET_BUFFER

2-Critical

MSP ISSU client failed to get buffer for message. Error: [dec] [chars]

The MSP ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

msi-proxy

"show logging and show checkpoint client"

MSP_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER

3-Error

'Message Type [dec]' is not supported by MSP ISSU client at peer

The MSP ISSU client at the peer supervisor is not compatible for this message type. The MSP client will be marked as incompatible with the peer.

msi-proxy

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MSP_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

MSP ISSU client capability exchange result incompatible.

The MSP ISSU client capability exchange have negotiated as incompatible with the peer.

msi-proxy

"show issu negotiated capability <Session_ID>"

MSP_ISSU-3-CAP_INVALID_SIZE

3-Error

MSP ISSU client capability list is empty.

The MSP ISSU client capability exchange list size is invalid.

msi-proxy

"show issu capability entires <Client_ID>"

RG_MEDIA-3-NOPROCESS

3-Error

Unable to create process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

rg-infra

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

RG_MEDIA-3-NOSOCKET

3-Error

Unable to open socket

The system was unable to initialize an IP connection for RG Protocol

rg-infra

"Make sure that there is at least one interface configured to run " "IP."

RG_MEDIA-4-BADSEQ

4-Warning

Group [dec]: Sequence number larger than expected - indicates packet loss

Sequence number expected from peer is too big this usually indicates packet loss

rg-infra

"Check for connectivity problems between the 2 peers."

RG_MEDIA-3-INVALIDPLATFORM

3-Error

Unsupported Platform

The peer platform is unsupported as a RG-pair

rg-infra

"Only like platforms can be configured as a RG pair."

RG_MEDIA-3-TIMEREXPIRED

3-Error

RG id [dec] Hello Timer Expired.

This router did not receive hello message from the peer within the configured hold time. This may result in a role change.

rg-infra

"Enter <CmdBold>show tech-support<NoCmdBold> " "<CmdBold>show history<NoCmdBold> commands collect " "all the information and error message and report it " "to your technical support representative."

RG_PROTOCOL-3-NOPROCESS

3-Error

Unable to create process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

rg-infra

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

RG_PROTOCOL-5-ROLECHANGE

5-Notice

RG id [dec] role change from [chars] to [chars]

RG role Init/Standby/Active has been changed

rg-infra

LOG_STD_NO_ACTION

RG_PROTOCOL-3-UNEXPECTEDACTIVE

3-Error

RG id [dec] unexpected Active peer [inet]

-

rg-infra

"If this is not a transient state check for connectivity problems " "or inconsistency of rg protocol timer configuration between " "the peers"

RG_PROTOCOL-4-UNEXPECTEDSTANDBY

4-Warning

RG id [dec] unexpected Standby peer [inet]

-

rg-infra

"If this is not a transient state check for connectivity problems " "or inconsistency of rg protocol timer configuration between " "the peers"

RG_TRANSPORT-3-NOPROCESS

3-Error

Unable to create process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

rg-infra

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

RG_TRANSPORT-3-TRANSFAIL

3-Error

Negotiation failure with error code: [dec]

The query_status in msg is not RG_TRANS_SUCCESS

rg-infra

"Make sure that there are no configuration errors."

RG_VP-3-NOPROCESS

3-Error

Unable to create process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

rg-infra

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

RG_VP-6-STANDBY_READY

6-Information

RG group [dec] Standby router is in SSO state

Indicates standby readiness

rg-infra

LOG_STD_NO_ACTION

RG_VP-6-BULK_SYNC_DONE

6-Information

RG group [dec] BULK SYNC to standby complete.

Indicagtes Standby bulk sync complete

rg-infra

LOG_STD_NO_ACTION

RG_AR-3-NOPROCESS

3-Error

Unable to create process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

rg-infra

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

RG_AR-3-NOPEER

3-Error

Peer does not exist for RG ID = [dec] with error code = [dec]

-

-

-

RG_FAULTS-6- PRICHANGE

6-Information

RG Infra RG[[dec]] Priority update. new priority [[dec]] old priority [[dec]] [chars]

The runtime priority of the group was updated

rg-infra

"Look at rg_infra trace for the cause for priority change"

RG_FAULTS-6- PRICONFCHANGE

6-Information

RG Infra RG[[dec]] Priority configuration changed. New runtime priority:[[dec]]

The configured priority changed runtime priority was affected

rg-infra

"No action need to be taken"

RG_FAULTS-3-NOPROCESS

3-Error

Unable to create a new process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

rg-infra

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

SADB-4-TREE_CORRUPTED

4-Warning

SADB : AVL Tree got corrupted

SADB's one of the AVL Trees got corrupted

eedge-policy

LOG_STD_NO_ACTION

LSLIB-3-INIT

3-Error

Unable to initialize LS LIB. [chars]

A software error occurred during initialization.

ls-lib

LOG_STD_ACTION

LSLIB-3-INTERNAL

3-Error

[chars]

An internal software error occurred.

ls-lib

LOG_STD_ACTION

LSLIB-4-EOD

4-Warning

[chars]

An LS LIB producer did not send EOD or an LS LIB consumer did not read EOD

ls-lib

LOG_STD_NO_ACTION

LSLIB-4-ATTR_MERGE

4-Warning

[chars]

An attribute of a node or a link or a prefix does not contain values from all groups LSA in case of OSPF and LSP in case of ISIS of an LS LIB producer

ls-lib

LOG_STD_ACTION

SR-3-SR_INTERNAL_ERR

3-Error

[chars]

SR_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

SR-3-SR_GB_CREATE_ERR

3-Error

Error Creating SR GB start [dec] end [dec]

Error creating sr gb

ribinfra

LOG_STD_RECUR_ACTION

SR-3-SR_LB_CREATE_ERR

3-Error

Error Creating SR LB start [dec] end [dec]

Error creating sr lb

ribinfra

LOG_STD_RECUR_ACTION

SR-6-SR_STATE_LOG

6-Information

Segment Routing MPLS [chars]

Segment Routing MPLS State

ribinfra

LOG_STD_RECUR_ACTION

SR-6-SR_LABEL_RANGE_LOG

6-Information

Segment Routing MPLS [chars]

Segment Routing MPLS Label Range Insufficient

ribinfra

LOG_STD_RECUR_ACTION

OMP_AGENT-3-TREE_INSERT_FAIL

3-Error

Topo-id 0x[hec] - Tree insertion failure for [chars].

Internal error - AVL tree insertion for specified object failed.

cedge-routing

LOG_STD_SH_TECH_ACTION

OMP_AGENT-3-TREE_DELETE_FAIL

3-Error

Topo-id 0x[hec] - Tree deletion failure for [chars].

Internal error - AVL tree deletion for specified object failed.

cedge-routing

LOG_STD_SH_TECH_ACTION

OMP_AGENT-3-VPN_CONVERT_FAIL

3-Error

Topo-id 0x[hec] - VPN Conversion failure for [chars].

Internal error - Topology to VPN conversion failure for specified object.

cedge-routing

LOG_STD_SH_TECH_ACTION

OMP_AGENT-3-VPN_NOT_FOUND

3-Error

Topo-id 0x[hec] - VPN for [chars] topo-id not found.

Internal error - VPN for the specified object's topology should exist but doesn't.

cedge-routing

LOG_STD_SH_TECH_ACTION

OMP_AGENT-3-MCAST_NO_REPL

3-Error

No replicator selected for VPN-%lld

SDWAN Multicast is configured but a reachable multicast replicator is not available.

-

"Assure an SDWAN multicast replicator is " "configured and reachable."

OMP_AGENT-3-MCAST_REPL_ADD_FAIL

3-Error

Topo-id: 0x[hec] - SDWAN multicast replicator [inet] addition failed.

Intenal error - SDWAN multicast replicator could not be added.

cedge-routing

LOG_STD_SH_TECH_ACTION

OMP_AGENT-3-MCAST_REPL_DELETE_FAIL

3-Error

Topo-id: 0x[hec] - SDWAN multicast replicator [inet] deletion failed.

Internal error -SDWAN multicast replicator could not be deleted.

cedge-routing

LOG_STD_SH_TECH_ACTION

OMP_AGENT-4-MCAST_JOIN_COUNT_OFF

4-Warning

Topo-id 0x[hec] - [chars] C-Multicast route count off for SDWAN router [inet] joins: [dec] prunes: [dec]

SDWAN multicast count of active joins is off as it should never be negative.

cedge-routing

"This can occur during transient conditions and " "should are not indicative of a failure unless " "there is also an SDWAN multicast outage."

OMP_AGENT-3-MCAST_SPT_ONLY_MISMATCH

3-Error

Multicast spt-only [chars]abled locally and [chars]abled on SDWAN router [inet] in VPN-%lld

SDWAN Multicast spt-only mode must be configured consistently for all SDWAN multicast routers in the VPN. Failure to do will prevent Any Source Multicast ASM from functioning properly.

-

"Assure an SDWAN multicast spt-only mode is " "configured consistently."

ISISL2-3-MCAST_RT_UPD_REQ_FAILURE

3-Error

[chars]-RIBInfo[chars]: Multicast RT [dec] [chars] [chars]: Failed to send the

ISISL2 client failed to send the Multicast route update request to MLMRIB

ISISL2_DDTS_COMPONENT

LOG_STD_ACTION

ISISL2-3-UNICAST_RT_UPD_REQ_FAILURE

3-Error

[chars]-RIBInfo[chars]: Unicast RT [dec] [chars]: Failed to send the

ISISL2 client failed to send Unicast route update request to MLURIB

ISISL2_DDTS_COMPONENT

LOG_STD_ACTION

ISISL2-3-UNICAST_RT_UPD_REP_FAILURE

3-Error

[chars]-RIBInfo[chars]: [chars] client receives the response of Unicast RT [chars] message with code:[dec] topoid:[dec]

ISISL2 client receives the response of Unicast RT update failure

ISISL2_DDTS_COMPONENT

LOG_STD_ACTION

ISISL2-3-MCAST_RT_UPD_REP_FAILURE

3-Error

[chars]-RIBInfo[chars]: [chars] client receives the response of Multicast RT [chars] message with code:[dec] topoid:[dec]

ISISL2 client receives the response of Multicast RT update failure

ISISL2_DDTS_COMPONENT

LOG_STD_ACTION

ISISL2-3-UNICAST_EVENT_UPD_FAILURE

3-Error

[chars]-RIBInfo[chars]: [chars] client failed to send Unicast event [dec] [dec] update request with error [chars]

-

-

-

ISISL2-3-MCAST_EVENT_UPD_FAILURE

3-Error

[chars]-RIBInfo[chars]: [chars] client failed to send Multicast event [dec] [dec] update request with error [chars]

-

-

-

RIP-3-NOSOCKET

3-Error

Unable to open socket

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

BGP-2-INSUFMEM

2-Critical

Insufficient memory for [chars] entry

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

BGP-3-EXTCOMMLIST_REFCOUNT_WRAPPING

3-Error

Extcommlist refcount [chars] wrapping

-

bgp

-

BGP-3-RADIXINIT

3-Error

Radix trie initialization failed

Initialization of the radix tree could not be accomplished because of\n\ a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

BGP-3-BADMASK

3-Error

Attempt to install route for [inet] without valid mask in [chars]

A route can not be installed without a valid mask.

-

LOG_STD_ACTION

BGP-6-NEXTHOP

6-Information

Invalid next hop [inet] received from [chars]: [chars]

The remote BGP peer sent in a route with an illegal next hop.The given\n\ route was ignored.

-

LOG_STD_NO_ACTION

BGP-6-MSGDUMP_LIMIT

6-Information

unsupported or mal-formatted message received from [chars]: \n[chars]

-

-

-

BGP-6-MALFORMEDATTR

6-Information

Malformed attribute in [chars]

-

-

-

BGP-6-MALFORMED_ATTR_SET

6-Information

Malformed attribute attr-set received from [chars]

-

-

-

BGP-6-NOT_SUPPORTED_NEXTHOP

6-Information

V6 nexthop not supported for afi/safi [dec]/[dec]

The remote BGP peer sent in a route with an invalid optional transitive attribute.

-

"This information message appears as router detects malformed\n\ optional attributes in BGP updates. However frequent occurrences\n\ of such event should be investigated."

BGP-6-ASPATH

6-Information

[chars] AS path [chars] received from [chars]: [chars]

-

-

-

BGP-6-ATTR_FLAG

6-Information

BGP update error: [chars] Wrong flag 0x[hec] received for [chars] attribute fixed by error handling

-

-

-

BGP-6-ATTR_DUP

6-Information

BGP update error: [chars] Duplicate [chars] attribute dropped by error handling

-

-

-

BGP-6-ATTR_WRONG_LEN

6-Information

BGP update error: [chars] Wrong length [dec] for [chars] dropped by error handling

-

-

-

BGP-6-ATTR_MISSING

6-Information

BGP update error: [chars] Missing mandatory attribute treat-as-withdraw by error handling

-

-

-

BGP-3-ADDROUTE

3-Error

Unable to add route for [chars] to radix trie

An addition to the radix trie could not be completed because\n\ of an error.

-

LOG_STD_ACTION

BGP-3-DELROUTE

3-Error

Unable to remove route for [chars] from radix trie

A deletion from the radix trie could not be completed because\n\ of an error.

-

LOG_STD_ACTION

BGP-3-ADDNETWORK

3-Error

Unable to add network for [chars] to radix trie

An addition to the radix trie could not be completed because\n\ of an error.

-

LOG_STD_ACTION

BGP-3-DELNETWORK

3-Error

Unable to remove network for [chars] from radix trie

A deletion from the radix trie could not be completed because\n\ of an error.

-

LOG_STD_ACTION

BGP-3-ADDBLOCK

3-Error

Unable to add blocked dynamic peer [chars]

Not able to save the specified data due to an error

-

LOG_STD_ACTION

BGP-3-DELBLOCK

3-Error

Unable to remove blocked dynamic peer [chars]

Not able to remove the specified data due to an error

-

LOG_STD_ACTION

BGP-3-ADDCID

3-Error

Unable to add Cluster ID [chars].

A addition to a cluster ID structure could not be completed because\n\ of an error.

-

LOG_STD_ACTION

BGP-3-DELCID

3-Error

Unable to remove Cluster ID [chars].

A deletion of a cluster-id could not be completed because\n\ of an error.

-

LOG_STD_ACTION

BGP-3-MUTEX

3-Error

Waiting for turn to execute after [dec] seconds.

-

-

LOG_STD_ACTION

BGP-3-ENHANCED_REFRESH_STALEPATH

3-Error

Net [chars] from bgp neighbor [chars][chars][chars] [chars] is stale after [chars] rate-limited

-

-

-

BGP-3-REFRESH_STALEPATH_COUNT

3-Error

[dec] stale-path[chars] deleted from bgp neighbor [chars][chars][chars] [chars] after [chars]

BGP peers are not consistent with each other.

-

"BGP peers are not consistent with each other report it to your\n\ technical support representative.."

BGP-3-DELPATH

3-Error

Attempted to delete path from an empty net for [chars]

A BGP path could not be deleted because of an error.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

BGP-3-RIBOUT_INCONSISTENCY

3-Error

Net [chars] in [chars][chars][chars] has rib-out inconsistency for update-group [dec] [chars]- outbound policy [chars] rib-out [chars] [chars][chars]

Bgp peers are not consistent with each other.

-

"Track the net copy the error message exactly as it appears and \n\ report it to your technical support representative."

BGP-3-NH_LABEL_INCONSISTENCY

3-Error

Net [chars] has Nexthop-Label inconsistency

Bgp peers are not consistent with each other.

-

"Track the net copy the error message exactly as it appears and \n\ report it to your technical support representative."

BGP-5-ADJCHANGE

5-Notice

neighbor [chars][chars][chars][chars] [chars]

A BGP neighbor has either come up or gone down. The message\n\ describes the change for it. This message appears only if the \n\ <Bold>log-neighbor-changes<nobold> command is configured for\n\ the BGP process.

-

"This informational message normally appears as routers and\n\ BGP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated."

BGP-3-NOTIFICATION

3-Error

[chars]

An error condition has been detected in the BGP session. A\n\ NOTIFICATION is being sent/received and the session will be reset.\n\ This message appears only if the <Bold>log-neighbor-changes<nobold> \n\ command is configured for the BGP process.

bgp

"This message represents an error in the session and its origin \n\ should be investigated. If the error is reported periodically copy\n\ it exactly as it appears and report it to your technical support \n\ representative."

BGP-3-NOTIFICATION_MANY

3-Error

[chars]

Notification sent to all the neighbors of the speaker.\n\ This message appears typically after doing 'clear ip bgp *'.

bgp

"If the error is unexpected report it to your technical support \n\ representative."

BGP-5-NBR_RESET

5-Notice

Neighbor [chars] reset [chars]

A BGP neighbor has been marked for reset. After all of resources assigned \n\ for the neighbor are freed the adjacency will be cleared down.\n\ This message appears only if the <Bold>log-neighbor-changes<nobold> \n\ command is configured for the BGP process.

bgp

"This message represents an error in the session was not reset \n\ because of administrative action of other valid event like an interface \n\ flap. If no valid event is detected report it to your technical support\n\ representative."

BGP-4-RIDSYNC

4-Warning

BGP routes are redistributed to OSPF. For synchronization to work you must manually configure the BGP router-id to be the same as the OSPF router-id.

For synchronization to work BGP router-id must be the same as the\n OSPF router-id at all times that the router is up.

bgp

"If synchronization is turned on between one instance of OSPF\n" "and BGP make sure to manually configure a BGP router-id which\n" "is identical to the one of that particular OSPF instance."

BGP-5-VERSION_WRAP

5-Notice

bgp version wrapped of [chars]

The BGP table version has reached its maximum value and\n\ wrapped around. The message describes this event.

-

"This message is informational. However frequent occurrences\n\ of such event might indicate high error rates or high packet\n\ loss in the network and should be investigated."

BGP-5-SLOWPEER_DETECT

5-Notice

Neighbor [chars][chars][chars] [chars] has been detected as a slow peer.

The BGP neighbor has been detected as a slow peer.

-

"The reason that the neighbor can not consume BGP update messages at the " "required rate should be investigated. Possible causes could be network " "congestion or high load on the peer."

BGP-5-SLOWPEER_RECOVER

5-Notice

Slow peer [chars][chars][chars] [chars] has recovered.

The slow BGP peer has recovered.

-

"This message is informational. The slow-peer has recovered."

BGP-5-AGGRESSIVE_SCAN_TIME

5-Notice

bgp scan-time configuration less than [dec] seconds can cause high cpu usage by BGP Scanner.

bgp scan-time configuration less than 15 seconds can cause high cpu usage by BGP Scanner.

-

"bgp scan-time configuration less than 15 seconds can cause high cpu " "usage by BGP Scanner. It is recommended to monitor the cpu usage of " "BGP Scanner."

BGP-3-ORF_PFXLIST

3-Error

Received misformatted prefixlist ORF from [chars]

-

-

-

BGP-3-ORF_EXTCOMMLIST

3-Error

Received misformatted extcommunity list ORF from [chars]

The received prefixlist ORF is misformatted.

bgp

"Check the prefixlist ORF implementation on the neighboring router."

BGP-4-MAXPFX

4-Warning

Number of prefixes received from [chars][chars][chars] afi [dec] reaches [dec] max [dec]

-

-

-

BGP-3-MAXPFXEXCEED

3-Error

Number of prefixes received from [chars][chars][chars] afi [dec]: [dec] exceeds limit [dec]

-

-

-

BGP-4-AFIMPORT

4-Warning

[chars] prefixes imported to [chars] vrf reached the limit [dec]

Number of prefixes imported from other address-family to a vrf reached configured limit

bgp

"Check the number of imported prefixes from the address-family and " "verify if the limit should be increased or the ip vrf import " "route-map is configured correctly."

BGP-3-BADROUTEMAP

3-Error

Bad parameters in the route-map [chars] applied for [chars]

This means the route-map should be changed

bgp

"Correct the route-map"

BGP-3-NEGCOUNTER

3-Error

Prefix-accepted counter negative for peer [chars] prefix [chars]

The counter value for accepted prefixes is wrong and less than zero

bgp

"This is a rare situation and is a result of internal problem.\n\ Reset the session to correct it."

BGP-3-INSUFCHUNKS

3-Error

Insufficient chunk pools for [chars] requested size [dec]

The static chunk pools size are not correct.

bgp

"Collect chunk and bgp summary. This is an internal software issue"

BGP-6-BIGCHUNK

6-Information

Big chunk pool request [dec] for [chars]. Replenishing with malloc

-

-

-

BGP-3-BGP_INCONSISTENT

3-Error

[chars] Inconsistent [chars]

Inconsistency in the data structures

bgp

"This is a rare situation and is a result of internal problem."

BGP-3-MARTIAN_IP

3-Error

[chars] Martian prefix [chars] in [chars]

Invalid MPLS label found in the BGP message

bgp

"This indicates that there is some problem on the remote router"

BGP-4-VPNV4NH_MASK

4-Warning

Nexthop [inet] may not be reachable from neigbor [chars] - not /32 mask

We are sending a vpnv4 route to this IBGP neighbor the nexthop\n\ address is our loopback which does not have /32 mask we are\n\ using OSPF on this loopback and the OSPF network type of this\n\ interface is LOOPBACK. OSPF advertizes this address\n\ as a host route with mask /32 regardless what mask is configured.\n\msgdef_recommended_action Configure the loopback used as the next hop with ip host mask

-

-

BGP-4-VPN_NH_IF

4-Warning

Nexthop [chars] may not be reachable from neigbor [chars] - not a loopback

We are sending a vpn route to this IBGP neighbor and the nexthop is one\n\ of our directly connected physical interfaces.\n\ The label for the next hop address may be removed in the MPLS cloud\n\ one hop soon. Since the P routers don't have VPN information\n\ they don't know where to forward packets with the BGP label.\n\ This could break connectivity between VPN sites.

bgp

"Use loopback interfaces as the nexthops for vpn IBGP neighbors."

BGP-5-DAMPENING_HIGH_MAX_PENALTY

5-Notice

Maximum penalty [dec] is more than allowed maximum [dec].

Configured dampening parameters may not be feasible. Maximum penalty is more than allowed maximum. Dampening will be OFF.

bgp

"Depending on the value of maximum penalty adjust maximum suppress " "time. Since maximum penalty is more than allowed maximum reduce " "maximum suppress time. Maximum penalty should be greater than " "suppress penalty but less than maximum allowable penalty."

BGP-5-DAMPENING_LOW_MAX_PENALTY

5-Notice

Maximum penalty [dec] is less than suppress penalty [dec]

Configured dampening parameters may not be feasible. Maximum penalty is less than configured suppress penalty. Dampening will be OFF

bgp

"Depending on the value of maximum penalty adjust maximum suppress " "time. Since maximum penalty is less than suppress penalty increase " "maximum suppress time. Maximum penalty should be greater than " "suppress penalty but less than maximum allowable penalty."

BGP-5-DAMPENING_DECAY_TIME

5-Notice

Decay time from maximum penalty to suppress penalty is [dec] secs. Maximum penalty: [dec] suppress penalty: [dec]

Configured dampening parameters may not be feasible. Time window between maximum penalty and suppress penalty may be low.

bgp

"If you think decay time from maximum penalty to suppress penalty " "is too low increase half-life time or maximum penalty values."

BGP-4-MAX_EXTCOMM_EXCEED

4-Warning

Exceeded limit of [dec] extended communities per advertised prefix

An attempt was made to advertise a prefix with an extended\n\ community attribute containing more extended communities\n\ than the allowed limit.

bgp

"Reduce the configured number of Route Targets or other extended\n\ communities that will be added to prefix advertisements so that\n\ the limit is not exceeded"

BGP-4-NBRTRACK

4-Warning

Route Tracking failed on memory. Neighbor tracking for route-fall-over will stop

Route tracking system failed to allocate memory. Neighbor route fall-over will stop tracking neighbor routes.

bgp

"Route tracking system failed to allocate memory. Neighbor " "route fall-over will stop tracking neighbor routes so that " "it can give away some memory. If you think system is stable " "then reconfigure neighbor route fall-over. If you get this " "message neighbor route-fallover has been deconfigured."

BGP-4-BFD_NOT_ONEHOP

4-Warning

BFD is supported for single hop neighbors. [chars] is not single hop neighbor

BFD is supported for single hop neighbors. The configured neighbor is not a single hop hence BFD is not enabled

bgp

"Deconfigure BFD from BGP as multihop " "neighbors are not supported in BFD"

BGP-4-NORTRID

4-Warning

BGP could not pick a router-id. Please configure manually.

BGP router-id has not been manually configured and BGP is unable to allocate a router ID from the IPv4 address of one of its interfaces.

bgp

"Make sure that there is at least one interface that is up and has a " "valid IPv4 address or configure the router-id manually."

BGP-4-ATTRNULL

4-Warning

A NULL attribute has been assigned to a path

The path should have been assigned a valid attribute but was incorrectly assigned a value of NULL

bgp

LOG_STD_ACTION

BGP-4-MSGDUMP

4-Warning

unsupported or mal-formatted message received from [chars]: \n[chars]

The remote BGP peer sent in a unsupported or mal-formatted message \n\ which caused the notification sent

-

LOG_STD_NO_ACTION

BGP_SESSION-5-ADJCHANGE

5-Notice

neighbor [chars] [chars][chars][chars] topology [chars] removed from session [chars]

A BGP neighbor topology was removed from a session. The message\n\ describes the change for it. This message appears only if the \n\ <Bold>log-neighbor-changes<nobold> command is configured for\n\ the BGP process.

-

"This informational message normally appears as routers and\n\ BGP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated."

BGP-4-BGP_RF_REG_FAILED

4-Warning

BGP failed to register with the redundancy facility.

BGP failed to register with the redundancy facility. If this happens stateful switchover for BGP will not work because BGP will not be able to sync any data from the active RP to the standby RP.

bgp

LOG_STD_ACTION

BGP-4-INVALIDSIZE

4-Warning

invalid size for as_array has been entered

-

-

LOG_STD_NO_ACTION

BGP-4-MAXDYNNBR

4-Warning

BGP:DN: Cannot create new neighbor [chars] for\nrange [chars]: maximum number of [dec] dynamic neighbors limit reached

Number of dynamically created subnet range neighhors reaches warning limit

bgp

"Check the number of listen range limit configured " "for dynamic subnet neighbors\n and verify if the " "limit should be increased."

BGP-3-BGP_NO_REMOTE_READ

3-Error

[chars] connection timed out - has not accepted a message from us for [dec]ms hold time [dec] messages pending transmition.

BGP failed to send UPDATE message to the neighbor for \n\ more than the hold timer. A Hold timer expiry NOTIFICATION \n\ is being sent and the session will be reset \n\ This message appears only if the <Bold>log-neighbor-changes<nobold> \n\ command is configured for the BGP process.

bgp

"BGP failed to send UPDATE message to the neighbor for \n\ more than the hold timer. A Hold timer expiry NOTIFICATION \n\ is being sent and the session will be reset."

BGP-5-BGP_UPDATE_ZERO_LENGTH

5-Notice

BGP failed to send update message because the message buffer size is calculated to be zero

BGP failed to send update message because the message buffer size is calculated to be zero. If this happens check the bgp buffer size being calculated while sending the update for both 4byte/2byte speakers.

bgp

LOG_STD_ACTION

BGP-5-BGP_MAX_MSG_LIMIT

5-Notice

BGP failed to send update message because the message size reached bgp maximum message size 4096.

BGP failed to send update message because the message size reached bgp maximum message size 4096. If this happens check the bgp paths that are learned if any of the paths have got many as-paths or ext-communities

-

LOG_STD_ACTION

BGP-4-BGP_OUT_OF_MEMORY

4-Warning

BGP resetting because of memory exhaustion.

BGP tried to perform an operation that required additional memory and was not able to allocate it.

bgp

"Reduce other system activity to ease memory " "demands or troubleshoot the system for memory " "fragmentation. If conditions warrant upgrade " "to a larger memory configuration."

BGP-4-BGP_LABELS_NOT_SUPPORTED

4-Warning

BGP neighbor [chars] does not support sending labels

You are attempting to configure send-label either directly or via a template for a neighbor which is connected over IPv6. Doing so is not supported

bgp

"Do not configure send-label for IPv6 peers"

BGP-4-BGP_BAD_RPKI_MESSAGE

4-Warning

BGP received an invalid RPKI message from rpki server [chars] [chars] [chars] hex dump: [chars]

BGP is configured to connect to an RPKI server. That server is sending malformed or incorrectly formatted messages to the router

bgp

"Check the configuration of our RPKI server " "and make sure that the server is updated to the " "latest version "

BGP-4-BGP_RPKI_ERROR_MESSAGE

4-Warning

BGP received an RPKI Error Report PDU from rpki server [chars] [chars] [chars] hex dump [chars]

The RPKI server that BGP is connected to is reporting. that the router sent it a malformed or incorrect PDU

bgp

"Check the configuration of the router and RPKI " "server and make sure that the server is updated " "to the latest version "

BGP-4-MULTIPATH_LOOP

4-Warning

This may cause traffic loop if not used properly command accepted.

Should be configured only at one of the edge routers that have ibgp \n\ peering among themselves.

bgp

LOG_STD_ACTION

BGP-5-BGP_MAX_NSR_MSG_LIMIT

5-Notice

BGP failed to send update message because the IPC to support NSR is having size less than the requested size.

BGP failed to send update message because the message size is bigger than the IPC of NSR. And the neighbor may not support route refresh capability. If this happens manually hard clear the neighbor session.

bgp

LOG_STD_ACTION

BGP-3-BGP_SUBSYSTEM_INIT_FAILED

3-Error

BGP subsystem initialization failed: [chars]

The BGP subsystem could not be initialized properly

bgp

LOG_STD_ACTION

BGP-4-BGP_INH_POLICY

4-Warning

Failed to inherit [chars] policy config '[chars]': [chars]->[chars] [chars] [chars]

BGP neighbor failed to inherit some policy configuration from a policy-template or peer-group because of some configuration imcompatibilities. The set of policy configurations that were compatible were still inherited.

bgp

LOG_STD_ACTION

BGP-4-BGP_INH_SESSION

4-Warning

Failed to inherit [chars] session config '[chars]': [chars]->[chars] [chars]

BGP neighbor failed to inherit some session configuration from a session-template or peer-group because of some configuration imcompatibilities. The set of session configurations that were compatible were still inherited.

bgp

LOG_STD_ACTION

BGP-4-BGP_SESSION_PARSE

4-Warning

Failed to parse [chars] neighbor config for neighbor [chars] [chars] [chars]

BGP neighbor failed to parse neighbor configuration.

bgp

LOG_STD_ACTION

BGP-3-BGP_SRTE_FAILURE

3-Error

BGP SRTE failed [chars] - Restarting BGP may be required

This is a rare situation and the system likely is running out of memory.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this messsage is\n\ after a configuration change the configuration should be reverted.\n\ BGP may need to be unconfigured and reconfigured to fully recover."

BGP-3-BGP_SR_POLICY_FAILURE

3-Error

BGP SR policy failed [chars] - Restarting BGP may be required

This is a rare situation and the system likely is running out of memory.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this messsage is\n\ after a configuration change the configuration should be reverted.\n\ BGP may need to be unconfigured and reconfigured to fully recover."

BGP-3-BGP_INTERNAL_ERR

3-Error

[chars]

BGP Internal Error

bgp

LOG_STD_ACTION

BGP-4-BGP_GR_RELOAD_UNSAFE_HOLDTIME

4-Warning

GR reload unsafe configured holdtime[dec] the default safe

You have configured an unsafe holdtime the default safe holdtime value is used instead.

bgp

"Configure the bgp holdtime value which is" " greater than the default safe holdtime" " value"

BGP-4-BGP_GR_RELOAD_UNSAFE_SESSION_RESTART_TIME

4-Warning

GR reload unsafe configured session restart time[dec]

You have configured an unsafe session restart time the default safe session restart time is used instead.

bgp

"Configure the bgp session restart time value " "which is greater than the default safe session" " restart time value"

BGP-4-BGP_GR_RELOAD_UNSAFE_STALEPATH_TIME

4-Warning

GR reload unsafe configured nsf stalepath time[dec]

You have configured an unsafe nsf stalepath time the default safe stalepath time is used instead.

bgp

"Configure the bgp nsf stalepath time value " "which is greater than the default safe stalepath" "time value."

BGP-4-AO_KEYCHAIN

4-Warning

[chars]

You have configured BGP AO to use a keychain which BGP can not use.

bgp

"Correct the key chain configuration."

BGP-6-ROUTER_HOLDBACK_TIMER

6-Information

BGP Router timed out waiting on dependant events

BGP Router timed out waiting on dependant events and will continue with its initializations.

bgp

LOG_STD_NO_ACTION

BGP_MPLS-3-LSDCONNECT

3-Error

[chars]

BGP VPNv4 failed to register to MPLS Forwarding component.

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-IPRMCONNECT

3-Error

[chars]

BGP VPNv4 failed to register to IPRM component.

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-7-IASLABELALLOC

7-Debug

Failed to create rewrite prefix [chars] result [chars]

BGP MPLS VPN rewrite creation failed.

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-7-IPv4LABELALLOC

7-Debug

Failed to allocate label for IPv4 prefix [inet]/[dec]

BGP MPLS IPv4 label allocation failed.

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-SIZEMISMATCH

3-Error

Label table size [dec] mismatch checkpt key creation failed

BGP MPLS Label Table size mismatch.

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-NBR_ROUTE

3-Error

[chars]

Problems with manipulating the bgp neighbor route needed for MPLS operations

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-VPN_REWRITE

3-Error

[chars]

Problems with installing updating or removing a VPN rewrite entry in the MPLS forwarding table

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-PER_VRF_AGGR

3-Error

pervrfaggr label: [chars]

This is related to PER VRF AGGREGATE LABEL feature

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-IPV4_AGGR_LABEL

3-Error

global aggr label: [chars]

This is related to a common AGGREGATE LABEL for all aggregate prefixes in global routing table.

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-GEN_ERROR

3-Error

[chars]

BGP MPLS related general runtime errors message contents will show the error

mpls-vpn

LOG_STD_ACTION

BGP_MPLS-3-LABELALLOC

3-Error

[chars]

An MPLS label could not be allocated for a prefix due to an internal error

mpls-vpn

LOG_STD_ACTION

BGP-3-BMP_MEMORY

3-Error

BMP Memory Utilization currently at %lu exceeds threshold %lu

BMP memory utilization tracked by BMP message alloc\n\ exceeds maximum memory allocation configured for BMP client

-

"Perform BMP deactivation on excessively churning\n\ BGP neighbors receiving large number of routes and reactivate\n\ after convergence"

BGP-5-BMP_ADJCHANGE

5-Notice

BMP Server [dec] - [chars]/[dec] connection [chars]

A BMP server TCP connection has either come up or gone down

-

"This informational message normally appears as\n\ BMP servers come up or go down. If the BMP server keeps flapping\n\ its connection continuously for whatever reason flapping delay\n\ timer kicks in to regulate reconnection attempts"

BGP-5-BMP_REFRESH_CAP_RCVD

5-Notice

Refresh cap not received from BGP nbr session [chars] BMP monitoring not possible

BMP monitoring of neighbor session is not possible in\n\ route-refresh scheme for session if refresh cap is not negotiated

-

"This informational message indicates BMP" " monitoring of BGP session is not possible without upgrading BGP peer" " to a software version that supports route-refresh cap"

MLTMGR-3-MLTMGR_INTERNAL_ERR

3-Error

[chars]

MLTMGR_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

RTMGR-3-GENERAL

3-Error

[chars]

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-UNLOCK_ERR

3-Error

Attempt to unlock active topology '[chars]' in VRF [chars] [chars]

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-VRF_ERR

3-Error

Topology VRF [chars] creation error

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_VRF_ERR

3-Error

Topology [chars] address-family [chars] has no VRF entry

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_IPMCAST_BASE_ERR

3-Error

Failed to create the base mcast topology in vrf [chars] with error [chars]

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_INTF_CTX

3-Error

Interface [chars] address-family [chars] topology context is NULL or the function [chars] is not set

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_SYNC_ERR

3-Error

Failed to duplicate active topology on standby rc=[dec] id [hec] [chars]

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_UNSUPPORTED_AFI

3-Error

Attempt to enable unsupported AFI 0x%X

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_AF_ENABLE_ERR

3-Error

Failed to enable AF base topology [chars] error [chars]

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_AFI_CTX

3-Error

Topology address-family [chars] context block is NULL.

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_INTF_INV_VRFID

3-Error

Interface [chars] with invalid vrfid 0x[hec]

An internal software error occurred.

RTMGR_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

RTMGR-3-TOPO_CACHE_INIT_ERROR

3-Error

[chars]

cached topo initialization failure

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_CACHE_ADD_ERROR

3-Error

[chars]

cached topo entry creation failure

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_CACHE_ERROR

3-Error

[chars]

cached topo failure

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_LCKMGR_INIT_ERROR

3-Error

[chars] manager init failure

Topology lock manager initialization failure

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_LCKMGR_GET_LOCK_COUNT_ERROR

3-Error

Failed to get lock count for topology[chars]

Topology lock manager get lock count failure

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_HA_LOCK_IVRF_TOPO

3-Error

Acquired a HA lock on an iVRF topology[chars]

Topology HA lock shouldn't be applied in an iVRF topology

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_UNSUPPORTED_API

3-Error

Topology API [chars] is unsupported due to [chars]

Topology API is unavailable

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_PROCESS_INIT_ERROR

3-Error

Topology process init failed due to [chars]

Topology process initialization failed

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

RTMGR-3-TOPO_SUBMODE_ERROR

3-Error

Unexpected transition from parser submode '[chars]'

An error occured while parsing the topology command

RTMGR_DDTS_COMPONENT

LOG_STD_ACTION

ODB-3-ODB_INTERNAL_ERR

3-Error

[chars]

ODB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

CLNS-4-LSPCKSUM

4-Warning

[chars][chars]: Bad L[dec] [chars] LSP [chars] checksum %04x received on [chars] length [dec] should be %04x bad count [dec]

-

-

"If the error is in a neighboring router's memory the problem\n\ will correct itself within 15 minutes. That router will detect\n\ its internal error and regenerate the corrupted data. This\n\ case is usually indicated by a single LSP ID appearing\n\ repeatedly in these messages. The same LSP ID might appear in\n\ this message on other routers as well.\n\\n\ If data-link corruption has caused the error check the link\n\ for errors and deal with them appropriately. This case is\n\ usually indicated by a number of different LSP IDs appearing\n\ in these messages."

CLNS-4-REDIRECT

4-Warning

Redirect found for non-route entry dst= [chars] next-hop= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

CLNS-4-NSAPIS

4-Warning

Invalid NSAP type in IS table: [hec] [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

CLNS-4-BADINTFCLNSMTU

4-Warning

[chars] Invalid interface clns MTU [dec]

This message occurs if the interface MTU becomes unusable\n\ while ISIS is running on the interface. This condition\n\ maybe temporary and recoverable.

-

LOG_STD_ACTION

CLNS-4-EDATFAIL

4-Warning

Encapsulation failed dst= [chars]

This message can occur when an interface is down and a static\n\ neighbor entry exists in the system's CLNS routing table. If this is\n\ not the case the message indicates an internal software error.

-

"Check the interface. If the interface is not down and no static\n\ neighbor entry exists for that interface call your technical support\n\ representative for assistance."

CLNS-3-NSAPES

3-Error

Invalid NSAP type in ES table: [hec] for [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

CLNS-4-AREALOST

4-Warning

[chars][chars]: Too many IS-IS areas--can\'t route to area [chars]

-

-

"Reconfigure the network so that the area has fewer area addresses or\n\ split the area into multiple areas."

CLNS-3-BADPACKET

3-Error

[chars][chars]: [chars] [chars][chars] from [chars] [chars]

An invalid packet was received from a neighboring router.

-

LOG_STD_ACTION

CLNS-3-CKSUMERR

3-Error

[chars][chars]: L[dec] LSP [chars] database checksum error restarting

A hardware or software error occurred.

-

LOG_STD_ACTION

CLNS-3-LSPFULL

3-Error

[chars][chars]: L[dec] LSP filled to capacity [chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

CLNS-3-LSPFULL_OVERLOAD

3-Error

[chars][chars]: Schedule L[dec] LSP to set overload bit

The LSP was filled to capacity and after applying any lsp-full suppress options we still can't recover out of it. So we are going to set overload bit on the LSP

-

LOG_STD_ACTION

CLNS-3-LSPTOOBIG

3-Error

[chars][chars]: L[dec] LSP [chars] size [dec] bigger than interface [chars] MTU [dec] LSP dropped

A software or hardware error occurred.

-

LOG_STD_ACTION

CLNS-5-ADJCHANGE

5-Notice

[chars][chars]: Adjacency to [chars] [chars] [chars] [chars]

-

-

"This informational message normally appears as\n\ routers and links go up or down. However unexpected adjacency loss might\n\ indicate high error rates or high packet loss in the network and should\n\ be investigated."

CLNS-5-FADJCHANGE

5-Notice

[chars][chars]: MPLS TE Forwarding Adjacency to [chars] [chars] [chars] [chars]

-

-

"This informational message normally appears as\n\ routers and links go up or down. However unexpected adjacency loss might\n\ indicate high error rates or high packet loss in the network and should\n\ be investigated."

CLNS-5-ADJCLEAR

5-Notice

[chars][chars]: All [chars]adjacencies cleared

-

-

"This informational message appears as a normal side effect\n\ of appropriate console or configuration commands."

CLNS-1-BKUPERR

1-Alert

ISIS: [chars] in [hex] ndb_next [hex] ndb_prev [hex] lsp_next [hex] lsp_prev [hex] metric [hex] route type [chars] index [dec] [chars] [hex]

An internal error occurred in the maintenance of the Intermediate\n\ System-to-Intermediate System ISIS backup route table.

-

LOG_STD_ACTION

CLNS-1-LINKERR

1-Alert

ISIS: [chars] in [hex] lsp_next [hex] lsp_prev [hex] index [dec] ver [dec] [chars] [hex]

An internal error occurred in the maintenance of Intermediate\n\ System-to-Intermediate System ISIS link-state packet LSP linkages.

-

LOG_STD_SH_TECH_ACTION

CLNS-3-TENT

3-Error

[chars][chars]: [chars]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS

-

LOG_STD_ACTION

CLNS-3-BADIFNUM

3-Error

ISIS[chars]: Bad if number pdb [hex] idb [hex] if [hex]

-

-

LOG_STD_SH_TECH_ACTION

CLNS-3-LSPDB

3-Error

[chars][chars]: Inconsistent LSPIX entry lsp [hex] index [dec] ixentry [hex] ixentry->lsp [hex]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS.

-

LOG_STD_SH_TECH_ACTION

CLNS-3-LSPCHAIN

3-Error

[chars][chars]: non-null [chars] pointer [hex] on freed LSP index [dec]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS.

-

LOG_STD_ACTION

CLNS-3-LSPIXARRNULL

3-Error

[chars][chars]: LSPix entry [dec] should be null is [hex]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS.

-

LOG_STD_ACTION

CLNS-3-LSPIXARRMATCH

3-Error

[chars][chars]: LSPix entry [dec] mismatch with LSP [hex] LSP [chars] is [dec] entry [dec]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS.

-

LOG_STD_ACTION

CLNS-3-LSPIXHEAD

3-Error

[chars][chars]: LSPix [chars] [dec] head [hex] doesn't match first prev [hex]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS.

-

LOG_STD_ACTION

CLNS-3-ONLIST

3-Error

ISIS: entry already threaded prev [hex] next [hex] index [dec] ver [dec]

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS.

-

LOG_STD_ACTION

CLNS-5-NSF_RESTART

5-Notice

ISIS[chars] NSF completion

ISIS performed an NSF restart

-

"This informational message appears as a normal side effect\n\ of a restart performed while NSF is enabled"

CLNS-5-NSF_STATUS

5-Notice

[chars][chars] NSF [chars]

This message used to print NSF status logs

-

"This informational message appears while NSF is enabled"

CLNS-5-NSF_NO_RP_SIGNAL

5-Notice

ISIS[chars] NSF cancelled - 'nsf interval' expiration pending

ISIS cancelled the NSF restart since either the active\n\ or standby RP had not been up long enough. In Cisco mode\n\ the active RP must signal that it has been up for a minimum\n\ of 'nsf interval' seconds. For IETF mode the standby RP must\n\ be up for a minimum of 'nsf interval' seconds.

-

"Review the setting of the 'nsf interval' command"

CLNS-5-NSF_ISSU_NEGO_FAIL

5-Notice

ISIS NSF cancelled - ISSU negotiation failed for NSF CISCO

ISIS cancelled the NSF restart since ISSU negotiation failed\n\ in Cisco mode.

-

"Review the output of 'show issu negotiated version' command"

CLNS-3-NSF_CP_ADJ_CID_MISMATCH

3-Error

ISIS[chars]: Checkpointed ADJ circuit id mismatch for [chars] [dec]/[dec]

-

-

-

CLNS-3-NSF_CID_FORCE_FAILURE

3-Error

ISIS[chars]: [chars] circuit id force to [hec] [dec] failed

A circuit ID forced assignment failed. The requested\n\ circuit ID is in use on another interface.

-

"At the current time there is no work around. The problem should\n\ disappear following the next switchover."

CLNS-3-LSPLIST

3-Error

ISIS: [chars] [dec] index [dec]

An internal error occurred in the Intermediate System-to-Intermediate System ISIS.

-

LOG_STD_ACTION

CLNS-3-IPLIST

3-Error

ISIS: [chars] [hex] [inet] [inet]

An internal error occurred in the Intermediate System-to-Intermediate System ISIS.

-

LOG_STD_ACTION

CLNS-3-IFLIST

3-Error

ISIS: [chars]: [chars]

An internal error occurred in the Intermediate System-to-Intermediate System ISIS.

-

LOG_STD_ACTION

CLNS-3-NSF_CP_BULK_SYNC_FAIL

3-Error

ISIS[chars] bulk sync failed to complete

The bulk sync of ISIS adjacency and LSP data from the active to\n\ the standby RP failed to complete successfully. Any attempt by\n\ ISIS to perform a non-stop forwarding restart may be incomplete.\n\ Note that ISIS should still converge correctly.

-

"At the current time there is no work around. The adjacency and\n\ LSP databases should still sync up between the active and standby RPs\n\ following completion of the bulk sync. If they do not report\n\ the output from 'show isis nsf' 'show clns neighbor' and\n\ 'show isis database' on both RPs and contact the TAC."

CLNS-3-NSF_CP_ERR

3-Error

ISIS[chars]: Checkpoint send error [chars]

An unrecoverable error occurred following a request to checkpoint\n\ a new or changed adjacency or LSP.

-

"At the current time there is no work around. If the error message\n\ continues to occur report the problem to the TAC."

CLNS-3-NSF_CP_INIT_ERR

3-Error

Checkpoint initialization error [chars]

An unrecoverable error occurred during initialization of the checkpoint\n\ client.

-

"At the current time there is no work around. If the error message\n\ continues to occur report the problem to the TAC."

CLNS-3-NSF_CP_IDB_ENCODE_FAIL

3-Error

ISIS[chars]: Interface [chars] cannot be encoded for nsf cisco

Adjacency and LSP information learned from this interface cannot be checkpointed due to an interface encoding error.

-

"Please verify that this interface type is supported for NSF in\n\ this release. If so report the problem to the TAC."

CLNS-3-PDBMODE_ADJDB_INCORRECT

3-Error

[chars][chars]: Adjacency DB should[chars] be [hex] is [hex]

Adjacency database must match process and does not.

isis

LOG_STD_ACTION

CLNS-3-PDBMODE_ADJDB_NOTEMPTY

3-Error

[chars][chars]: Adjacency DB should be empty before deleting and is not

Adjacency database must be empty before deleting and is not.

isis

show clns neighbors

CLNS-3-PDBMODE_TRANS_INVALID

3-Error

[chars][chars]: Transition target for pdb mode is invalid: \n\ current [dec] target [dec]

ISIS process received request to transition to invalid state

isis

LOG_STD_ACTION

CLNS-4-AUTH_FAIL

4-Warning

[chars]: [chars][chars] authentication failed

An ISIS packetIIH CSNP PSNP or LSP was received and did not

-

"If the error persists check the originating router for matching " "authentication mode and password."

CLNS-4-GR_FAIL

4-Warning

[chars] failed: Invalid PDB GR Sub-block for ISIS-[chars]

IS-IS Graceful Reload was not completed due to invalid PDB GR Sub-Block.

-

"If the error persists check the IS-IS configuration for that instance"

CLNS-4-GR_REG_FAIL

4-Warning

Failed to register with GR_INFRA rc=[dec]

IS-IS failed to register with GR_INFRA

-

"If the error persists restart the IS-IS process"

CLNS-4-GR_INVALID_CLIENT

4-Warning

GR_INFRA failed to assign a valie client ID to IS-IS

IS-IS received invalid client ID from GR_INFRA

-

"If the error persists restart the IS-IS process"

CLNS-4-OTV_SITE_FAIL

4-Warning

[chars]: [chars] site info update failed

An ISIS packetIIH CSNP PSNP was received and failed to

-

"If the error persists check the originating router "

CLNS-4-OTV_SITE_ID_MISMATCH

4-Warning

Site id [chars] from neighbor [chars] does not match local site id

OTV Site ID received from a neighbor in the same site has a different site id indicating a misconfiguration error.

-

"Verify site id configuration and/or site connecetivity "

CLNS-4-OTV_OVERLAY_SITE_ID_MISMATCH

4-Warning

[chars] Site id [chars] from neighbor [chars] does not match site id [chars] received in site hellos.

A neighbor in the same site is sending a different site ID in its overlay hellos than in its site hellos

-

"Verify site id configuration and/or site connecetivity "

CLNS-4-LSP_MAXSEQ

4-Warning

[chars][chars]: attempt to exceed LSP maximum sequence number for LSP [chars]

Attempt was made to exceed maximum sequence number for an LSP.

-

"Protocol will shutdown for max-lsp-lifetime + 1 minute.\n\ This is a very unlikely natural occurrence.\n\ Investigate to find the source of any out of order reception\n\ generation or incrementing of this LSP's sequence number."

CLNS-6-DFT_OPT

6-Information

Protocol timers for fast convergence are [chars].

Routing-default-optimize state

isis

LOG_STD_ACTION

CLNS-7-DEBUG_TRACEBACK

7-Debug

Debug: [chars]

Debug information.

-

"No action required"

CLNS-4-DUPSYSTEM

4-Warning

[chars][chars]: possible duplicate system ID [chars] detected

This is a configuration error.

-

"One of the duplicate IDs needs to be corrected."

CLNS-4-DUPSNPA

4-Warning

[chars][chars]: Duplicate SNPA [chars] detected

This may be a configuration error.

-

"One of the duplicate SNPA addresses needs to be corrected."

CLNS-3-CRYPTOERR

3-Error

[chars][chars]: Error in filling MD5 digest for [chars] PDU

An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS while filling in the crypto digest for the PDU.

-

LOG_STD_ACTION

CLNS-7-DEBUGMSG

7-Debug

[chars]: %08x %08x %08x %08x %08x %08x

Internal use only

clns

"Should not be seen in the field"

CLNS-4-BADIPMSK

4-Warning

ISIS[chars]: Inconsistent ip prefix and mask[inet]%#m in ISIS LSP:

The system received a link-state packet LSP which contained a

-

LOG_STD_SH_TECH_ACTION

CLNS-3-LSPLISTERR

3-Error

ISIS[chars]: LSP list traversal incomplete [chars]

An internal error occurred in the Intermediate System-to-Intermediate System ISIS.

-

LOG_STD_ACTION

CLNS-3-BFDCLTERR

3-Error

[chars]: ISIS BFD client register fails with error[dec]

-

-

-

CLNS-3-TERRRERR

3-Error

[chars] called on standby

An ISIS RRR support routine has been incorrectly called on standby

isis

LOG_STD_ACTION

CLNS-3-MFIERR

3-Error

ISIS MFI API error: [chars] [chars]

ISIS calling MFI API failed.

isis

LOG_STD_ACTION

CLNS-4-SIDRANGE

4-Warning

[chars] [dec] for [inet]%m is out of SRGB range [dec] via [inet]

ISIS tried to bind a label to a prefix that is out of SRGB range

isis

LOG_STD_ACTION

CLNS-3-SIDERR

3-Error

ISIS SID conflict detected for [inet]%m

There is more than one node advertising the same prefix.\n\ But the prefix SID is different.

isis

LOG_STD_ACTION

CLNS-3-LSPGENSPACE

3-Error

LSPGEN reserved space [dec] is too small. Needed [dec]. \n\ Cannot add [inet]%m

ISIS encountered an inconsistency between LSPGEN cache usage and the LSP space.

isis

LOG_STD_ACTION

CLNS-3-LSPGENERROR

3-Error

LSPGEN cache usage is inconsistent with actual LSP space usage. \n\ Cannot add [chars]

ISIS encountered an inconsistency between LSPGEN cache usage and the LSP space.

isis

LOG_STD_ACTION

CLNS-3-LSPGENRCTLV

3-Error

LSPGEN cache space is not reserved for router capability TLV.

ISIS encountered the LSPGEN cache space is not reserved for the router capability TLV.

isis

LOG_STD_ACTION

CLNS-3-CASEERROR

3-Error

Case statement error [dec] is out of bound

ISIS encountered an internal programming error

isis

LOG_STD_ACTION

CLNS-3-VLANRANGEERR

3-Error

[chars]: invalid vlan range received begin [dec] end [dec] step [dec]

An invalid vlan range has been received in lsp

-

LOG_STD_ACTION

CLNS-3-MFIBINDERR

3-Error

MFI label bind error reported for [inet]%m - [chars]

MFI reported an error when ISIS tried to bind a prefix with the label

isis

LOG_STD_ACTION

CLNS-4-CORRUPTLIFETIME

4-Warning

[chars][chars]: possible corrupted lifetime [dec] secs for L[dec] lsp [chars] from SNPA [chars] detected

ISIS received the remaining lifetime value which is less than ZeroAgeLifetime 60 secs

-

LOG_STD_ACTION

CLNS-3-NONZEROHT

3-Error

[chars][chars]: Received L[dec] LSP [chars] with [dec] secs Remaining Lifetime that contain POI TLV

ISIS received LSP with non-zero Remaining Lifetime that contain POI TLV

isis

LOG_STD_ACTION

CLNS-3-INTERNALERR

3-Error

Internal error - [chars]

An internal software error has occured

isis

LOG_STD_ACTION

CLNS-4-NOVALIDKEY

4-Warning

No valid authentication key is available

-

isis

"Configure a new key"

CLNS-5-EXPIREDKEY

5-Notice

Packet [chars] with expired Key ID [dec].

The Key ID in use has a lifetime and the system time is not within that lifetime

isis

"Configure a new key"

CLNS-4-INVALIDKEY

4-Warning

Key ID [dec] [chars]on interface [chars]

The ID is not found in the configured key chain

isis

"Configure a new security association with the Key ID"

CLNS-4-INVALIDKCNAME

4-Warning

Key chain name [chars] is invalid

The key-chain name configured under ISIS does not match global key chain configuration.

isis

"Fix configuration"

CLNS-4-INVALIDKCKEYID

4-Warning

Key ID [dec] in key chain [chars] is invalid

They Key ID configured in the key chain is out of range for ISIS. This may happen because the key chain allows Key ID values outside of the range which is acceptable for ISIS.

isis

"Configure a new security association with a Key ID that is in " "the range 1-65535"

CLNS-5-NOKEY

5-Notice

Key ID [dec] in key chain [chars] does not have a key

ISIS has been configured to use cryptographic authentication however an key password has not been configured

isis

"Configure a key for the security association"

CLNS-5-NOCRYPTOALG

5-Notice

Key ID [dec] in key chain [chars] does not have a cryptographic algorithm

ISIS has been configured to use cryptographic authentication however an algorithm has not been configured

isis

"Configure a cryptographic-algorithm for the security association"

CLNS-4-REDIST_MAX_PFX

4-Warning

Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes

We have reached the maximum number of redistributed prefixes

-

"Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake"

CLNS-4-REDIST_THR_PFX

4-Warning

Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes

We have reached the threshold level of number of redistributed prefixes

-

"Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake"

CLNS-4-DISALLOWED_TLV_IN_PURGE

4-Warning

Received disallowed TLV [dec] in Purge LSP

ISIS received a Purge LSP containing a disallowed TLV

isis

"Check ISIS routing protocol for RFC6233 compliant"

CLNS-4-FLEX_CFG_OVER_LIMIT

4-Warning

Number of flex algos reach the limit

Number of configured flex-algos reach the limit and configuration of addtional flex-algos is not accepted in order to avoid known issues with highly scaled configuration. Limit will be removed in one of the future release.

isis

"Accept configuration limit."

CLNS-5-FLEX_DEFN_CHANGE

5-Notice

[chars]: Flex-Algo [dec] Level-[dec] definition changed priority [dec] source System-ID [chars]

Flex algorithm definition changed

isis

"This is an informational message that appears when" "flex-algo definition changes"

CLNS-5-FLEX_DEFN_ENABLE_DISABLE

5-Notice

[chars]: Flex-Algo [dec] is [chars] for Level-[dec]

Flex algorithm enabled or disabled

isis

"This is an informational message that appears when" "flex-algo is enabled or disabled"

CLNS-5-FLEX_ALGO_DISABLED_NO_DEFN

5-Notice

[chars]: Flex-Algo [dec] is disabled for Level-[dec] no best definition available

Flex algorithm is disabled because best definition is not available

isis

"This is an informational message that appears when" "flex-algo is disabled because of no best definition"

TID_HA-3-TXFAIL

3-Error

[chars] name '[chars]' tableid [dec] action [dec]

Failed to send internal tableid information

mpls-vpn

LOG_STD_ACTION

TID_HA-3-TXFAILCF

3-Error

[chars] name '[chars]' tableid [dec] action [dec] checkpoint code [dec]

Failed to send internal tableid information due to an error in the checkpoint facility

mpls-vpn

LOG_STD_ACTION

TID_HA-3-RXFAIL1

3-Error

[chars]

Error while receiving a tableid synchronization message

mpls-vpn

LOG_STD_ACTION

TID_HA-3-RXFAIL2

3-Error

[chars] type [dec] version [dec] flags [hec]

Error while receiving a tableid synchronization message

mpls-vpn

LOG_STD_ACTION

TID_HA-3-RXFAIL3

3-Error

[chars] type [dec] version [dec] flags [hec] application [dec] action [dec] tableid [dec] name '[chars]'

Error while receiving a tableid synchronization message

mpls-vpn

LOG_STD_ACTION

TID_HA-3-RXFAIL_TOPO

3-Error

[chars] type [dec] version [dec] flags [hec] action [dec] topoid 0x[hec] vrfid 0x[hec] afi [dec] name '[chars]'

Error while receiving a topo add message

mpls-vpn

LOG_STD_ACTION

TID_HA-3-RXFAIL_TYPE

3-Error

[chars] @[hec] type [dec] len [dec]

Unrecognized message type

mpls-vpn

LOG_STD_ACTION

TID_HA-3-SYNCFAIL

3-Error

[chars]

Internal tableid information may have not been synced to the standby unit correctly

mpls-vpn

"Reload the standby unit. If the error condition perists copy the " "error message exactly as it appears and contact your technical " "support representative"

TID_HA-3-SYNCFAILCF

3-Error

[chars] checkpoint code [dec]

Internal tableid information may have not been synced to the standby unit correctly due to an error in the checkpoint facility

mpls-vpn

"Reload the standby unit. If the error condition perists copy the " "error message exactly as it appears and contact your technical support " "representative"

TID_HA-3-ISSUERR

3-Error

[chars] [chars]

There was an error during an ISSU versioning operation

mpls-vpn

LOG_STD_ACTION

TID_HA-3-ISSUERRCF

3-Error

[chars] checkpoint code [dec]

There was an error during an ISSU versioning operation due to an error in the checkpoint facility

mpls-vpn

LOG_STD_ACTION

TID_HA-3-ISSUERRSESS

3-Error

Invalid session type [dec]

Invalid session type

mpls-vpn

LOG_STD_ACTION

TID_HA-3-ISSU_ERR

3-Error

[chars]: [chars] [chars]

There was an error during an ISSU versioning operation

mpls-vpn

LOG_STD_ACTION

TID_HA-7-ISSU_INFO

7-Debug

[chars]: [chars] [chars]

ISSU versioning operation

mpls-vpn

LOG_STD_ACTION

IP_VRF-3-VRF_SUBSYSTEM_INIT_FAILED

3-Error

VRF subsystem initialization failed: [chars]

The VRF subsystem could not be initialized

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_CREATE_FAIL

3-Error

[chars]

IP VRF creation failed.

vrfinfra

LOG_STD_ACTION

IP_VRF-3-MAX_VRF

3-Error

[chars]

Related to MAX number of VRFs

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_TABLEID_INCONSISTENT

3-Error

[chars]

VRF tableid inconsistent between two RPs.

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_CMN_INVALID_PARAM

3-Error

[chars]

Invalid parameter.

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_IVRF_ERROR

3-Error

[chars]

VRF infrastructure failure for Platform VRFs.

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_AF_ENABLE_ERROR

3-Error

Failed to enable address-family [chars] in VRF [chars]: [chars]

Failed to enable AF in a VRF

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_MT_UPDATE_ERROR

3-Error

Failed to update multicast multi-topology mode for address-family [chars] in VRF [chars]: [chars]

Failed to update multicast multi-topology mode in a VRF

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_UNLOCK_ERROR

3-Error

Failed to unlock VRF [chars]: [chars]

Failed to unlock a VRF

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_LOCK_ERROR

3-Error

Failed to lock VRF [chars]: [chars]

Failed to lock a VRF

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_GET_LOCK_COUNT_ERROR

3-Error

Failed to get lock count for VRF [chars]: [chars]

Failed to lock count from a VRF

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_LCKMGR_INIT_ERROR

3-Error

[chars]

VRF lock manager initialization failure

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_LCKMGR_CONTEXT_INIT_ERROR

3-Error

Failed to initialize lock manager context for vrf [chars][dec] with error [chars]

VRF lock manager initialization failure

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_ID_INVALID_ERROR

3-Error

Invalid VRF id 0x[hec] in [chars]

VRF ID Invalid

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_IFLIST_NOT_EMPTY

3-Error

VRF [chars] iflist is not empty in [chars]

VRF iflist is not empty

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_IFLIST_ADD

3-Error

Error adding [chars] to interface list of VRF [chars]

VRF interface association failed

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_IFLIST_DEL

3-Error

Error removing [chars] from interface list of VRF [chars]

VRF interface disassociation failed

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_HDVRF_ERROR

3-Error

HDVRF: [chars]

HDVRF related error messages

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_CCA_ERROR

3-Error

VRF-CCA: [chars]

VRF manager encountered a command inheritance error

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_AF_ACTIVATE

3-Error

Unable to activate VRF support for address family [chars]

The VRF subsystem was unable to initialize support for the indicated address family

vrfinfra

LOG_STD_ACTION

IP_VRF-3-VRF_CONFIG_IF_LOCK_ERROR

3-Error

Failed to acquire interface configuration lock

VRF interface association failed

vrfinfra

LOG_STD_ACTION

IP_VRF-4-VRF_CONFIG_IF_LOCK_DELAY

4-Warning

Unexpected delay while acquiring interface configuration lock

Unexpected delay in VRF interface association

vrfinfra

LOG_STD_NO_ACTION

IP_VRF-4-VRF_CONFIG_IF_LOCK_TAKEN

4-Warning

Acquired interface configuration lock

Unexpected delay in VRF interface association

vrfinfra

LOG_STD_NO_ACTION

IP_VRF-4-VRF_CONFIG_IF_LOCK_IGNORED

4-Warning

Ignored interface configuration lock [dec] times

Processing is continuing without obtaining the VRF interface configuration lock

vrfinfra

LOG_STD_NO_ACTION

OSPFv3-3-CF_NOMEM

3-Error

Unable to allocate checkpoint buffer: [chars]

NSR operation may be degraded to a lack of memory.

ospf

show tech-support ospfv3

OSPFv3-3-CF_NOMSG

3-Error

No space in checkpoint buffer

NSR operation may be degraded to a lack of memory.

ospf

show tech-support ospfv3

OSPFv3-4-CF_UNKNOWN_STATUS

4-Warning

Unknown checkpoint status: [dec]

An internal error occured.

ospf

show tech-support ospfv3

OSPFv3-4-CHKPT_UNKNOWN_TYPE

4-Warning

Invalid checkpoint message type: [dec]

An internal error occurred.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_NOMEM

3-Error

Unable to allocate checkpoint queue entry

NSR will not operate due to a failure communicating with the standby.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_SEND_FAIL

3-Error

Checkpoint message send failed: [chars]

NSR will not operate due to a failure communicating with the standby.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_IDB_ENCODE_FAIL

3-Error

Interface [chars] cannot be encoded for NSR

Adjacency and interface information learned from this interface cannot be checkpointed due to an interface encoding error.

ospf

"Please verify that this interface type is supported for NSR in " "this release. If so report the problem to the TAC."

OSPFv3-3-CHKPT_IDB_DECODE_FAIL

3-Error

Interface cannot be decoded for NSR: [chars]

Adjacency and interface information for an interface cannot be checkpointed due to an interface decoding error.

ospf

"Please verify that this interface type is supported for NSR in " "this release. If so report the problem to the TAC."

OSPFv3-3-CHKPT_MSG

3-Error

Invalid checkpoint message: [chars] [chars]

NSR will not operate due to an error in a checkpoint message.

ospf

show tech-support ospfv3

OSPFv3-4-CHKPT_MSG_SEQ

4-Warning

Invalid checkpoint message sequence number: received [dec] expected [dec]

NSR has detected a duplicate checkpoint message.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_MSG_LOST

3-Error

Checkpoint message lost

NSR will not operate due to a dropped checkpoint message.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_STATUS_LOST

3-Error

Checkpoint status lost

NSR will not operate due to a missing checkpoint status message.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_STBY_NO_LSA_BUFFER

3-Error

Standby synchronization error: no LSA buffer

NSR will not operate due to an internal error.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_STBY_LSDB_INVALID

3-Error

Standby link-state database validation failed expected/found count: [dec]/[dec] chksum: 0x%llx/0x%llx

NSR will not operate due to an error on the standby.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_STBY_NO_NBR

3-Error

Standby synchronization error: could not find neighbor [chars] [inet] %P

NSR will not operate due to an internal error.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_STBY_NO_LSDB

3-Error

Standby synchronization error: could not add lsa type [dec]

NSR will not operate due to an internal error.

ospf

show tech-support ospfv3

OSPFv3-3-CHKPT_STBY_SYNC_LOST

3-Error

Standby synchronization lost for OSPFv3-[dec] AFI [chars] VRF [chars] was: [chars]

Synchronization between the active and standby OSPFv3 has been lost.

ospf

show tech-support ospfv3

OSPFv3-3-ISSU_NEGOTIATION

3-Error

ISSU negotiation[chars] error: [dec] [chars]

The OSPFv3 ISSU session could not complete negotiation. This failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ospf

LOG_STD_ACTION

OSPFv3-3-NSR_FAILED

3-Error

NSR can not recover checkpointed data for process [dec]

An NSR failover could not be performed because OSPFv3 on the standby was not synchronized

ospf

show tech-support ospfv3

OSPFv3-5-LASTKEYEXP

5-Notice

The last key has expired in key-chain [chars].

None of the security associations have a lifetime that include the current system time.

ospf

"Configure a new security association or alter the lifetime of a " "current security association"

OSPFv3-4-NOVALIDKEY

4-Warning

No valid authentication key under key-chain [chars]

-

ospf

"Configure a new key"

OSPFv3-5-EXPIREDKEY

5-Notice

Packet [chars] on interface [chars] with expired Key ID [dec].

The Key ID in use has a lifetime and the system time is not within that lifetime

ospf

"Configure a new key"

OSPFv3-4-INVALIDSAID

4-Warning

SA ID '0' [chars]on interface [chars]

The SA ID '0' is considered invalid

ospf

"Configure a new security association with the valid Key ID"

OSPFv3-4-INVALIDKCNAME

4-Warning

Key chain name [chars] is invalid

The key-chain name configured under OSPF interface does not match global key chain configuration.

ospf

"Fix configuration. Either remove ospf authentication command " "or configure key chain in global configuration mode."

OSPFv3-4-INVALIDKCKEYID

4-Warning

Key ID [dec] in key chain [chars] is invalid

They Key ID configured in the key chain is out of range for OSPF. This may happen because the key chain allows Key ID values outside of the range which is acceptable for OSPFv3.

ospf

"Configure a new security association with a Key ID that is in " "the range 1-65535"

OSPFv3-5-NOKEY

5-Notice

Key ID [dec] in key chain [chars] does not have a key

OSPF has been configured to use cryptographic authentication however an key password has not been configured

ospf

"Configure a key for the security association"

OSPFv3-5-NOCRYPTOALG

5-Notice

Key ID [dec] in key chain [chars] does not have a valid cryptographic algorithm

OSPF has been configured to use cryptographic authentication however an algorithm has not been configured

ospf

"Configure a cryptographic-algorithm for the security association"

OSPFv3-5-INVALIDSADATA

5-Notice

Key chain [chars] key [dec]. Data not valid to [chars] packet on [chars]

OSPFv3 has been configured to use cryptographic authentication using key-chain configuration option. SA data are not however completelly valid and can not be used to authenticate sent packet or verify received received packet

ospf

"Verify global key chain configuration. Is it configured with " "key ID and algoritm supported by OSPFv3 and is key string specified?"

OSPFv3-3-INTERNALERR

3-Error

[chars] Internal error: [chars] [chars]

An internal software error occurred.

-

LOG_STD_ACTION

OSPFv3-3-NOSTART

3-Error

Unable to start process: [chars]

An internal software error occurred.

ospf

LOG_STD_ACTION

OSPFv3-3-NOBACKBONE

3-Error

[chars] Flagged as being an ABR without a backbone area

-

-

"Restart the OSPF process."

OSPFv3-6-BADCHKSUM

6-Information

[chars] Checksum Failure in database in area [chars]: LSA Type [hec] Link State Id [inet] Old Checksum [hex] New Checksum [hex]\n

OSPF has detected a checksum error in the database due to memory\n\ corruption.

-

"Restart OSPF process."

OSPFv3-4-ERRRCV

4-Warning

[chars] Received invalid packet: [chars] from %P [chars]

An invalid OSPF packet was received. Details are included in the error\n\ message. The cause might be a misconfigured OSPF or an internal error\n\ in the sender.

-

"Check the OSPF configuration of the receiver and the sender for\n\ inconsistency."

OSPFv3-4-MANET_VER_MISMATCH

4-Warning

Non-standard MANet implementation detected on neighbor [inet]

An OSPF packet was received with LLS data but without a Type 1 Extended Options and Flags TLV indicating an older MANet implementation.

-

"Check the version of software running on the neighbor."

OSPFv3-4-AREA_MISMATCH

4-Warning

[chars] Received packet with incorrect area from %P [chars] area [inet] packet area [inet]

An OSPF packet was received with an area ID in its header which does not match the area of this interface.

-

"Check the OSPF configuration of the receiver and the sender " "for inconsistency."

OSPFv3-4-NONEIGHBOR

4-Warning

[chars] Received [chars] from unknown neighbor [inet]

OSPF hello database description or database request packet was\n\ received but the router could not identify the sender.

-

"This situation should correct itself. " LOG_STD_RECUR_ACTION

OSPFv3-4-BADLENGTH

4-Warning

[chars] Invalid length [dec] in [chars] OSPF packet type [dec] from %P ID [inet] [chars]

-

-

-

OSPFv3-4-BADLSATYPE

4-Warning

[chars] Invalid lsa: [chars]: Type 0x[hec] Length 0x[hec] LSID [dec] from [inet] %P [chars]

The router received an LSA with invalid data. LSA contains invalid LSA type wrong checksum or wrong length. The cause is either memory corruption or unexpected behavior on a router.

-

"From a neighboring address locate the problem router.\n" "1 Collect a running configuration of the router by entering the"

OSPFv3-4-NORTRID

4-Warning

Process [chars] could not pick a router-id please configure manually

OSPFv3 failed while attempting to allocate a router ID from the IP\n\ address of one of its interfaces.

-

"Ensure that at least one interface is active up and has a valid IP "

OSPFv3-4-VIRTUAL_IN_NON_BACKBONE

4-Warning

[chars] Virtual link information found in non-backbone area: [chars]

An internal error occurred.

-

LOG_STD_SH_TECH_ACTION

OSPFv3-3-DBEXIST

3-Error

[chars] DB already exist : area [chars] lsid [inet] adv [inet] type 0x[hec]

OSPF has a problem locating the LSA which could lead to a memory leak.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-6-ZERO_BANDWIDTH

6-Information

[chars] interface [chars] has zero bandwidth

The interface reports its bandwidth as zero.

-

LOG_STD_NO_ACTION

OSPFv3-5-ADJCHG

5-Notice

Process [dec][chars][chars] Nbr [inet] on [chars] from [chars] to [chars] [chars]

An OSPF neighbor has changed state. The message describes \n\ the change and the reason for it. This message appears only \n\ if the <Bold>log-adjacency-changes<NoBold> command is\n\ configured for the OSPF process.

-

LOG_STD_NO_ACTION

OSPFv3-3-INIT_IDB

3-Error

OSPF is enabled on [chars] during idb initialization

An internal error occurred.

-

LOG_STD_SH_TECH_ACTION

OSPFv3-4-DUP_RTRID_NBR

4-Warning

[chars] detected duplicate router-id [inet] from %P on interface [chars]

-

-

-

OSPFv3-4-DUP_RTRID_AREA

4-Warning

[chars] Detected router with duplicate router ID [inet] in area [chars]

OSPF received hello packet from a neighbor which has the same\n\ router-id as this routing process. A full adjacency cannot be \n\ established.

-

"OSPF router-id should be unique. Change the neighbors router-id"

OSPFv3-4-NET_TYPE_MISMATCH

4-Warning

Received Hello from [inet] on [chars] indicating a potential \n\ network type mismatch

OSPF received hello packet from a neighbor which has a non-zero \n\ value in the DR or BDR field but this router is configured as \n\ point-to-point on this interface. This indicates a network type \n\ mismatch.

-

"The network type must be configured the same for all devices \n\ attached to the same link."

OSPFv3-3-RECONF_VL

3-Error

Process [chars] is changing router-id. Reconfigure virtual link neighbors with our new router-id

OSPF process is being reset and it is going to select a new router-id. This will bring down all virtual links. To make them work again virtual link configuration needs to be changed on all virtual link neighbors.

-

"Change virtual link configuration on all the virtual link " "neighbors to reflect our new router-id."

OSPFv3-6-UNEXPECTED_MESSAGE

6-Information

OSPFv3 has received an unexpected message: %0x / %0x

OSPFv3 has received an unexpected interprocess message.

-

LOG_STD_SH_TECH_ACTION

OSPFv3-3-INVALID_ENCR_KEY

3-Error

Invalid encrypted key [chars].

The specified encrypted key is not valid.

-

"Either specify a cleartext key and enter the <CmdBold>service " "password-encryption<NoCmdBold> command for encryption or ensure " "that the specified encrypted key is valid. If the specified " "encrypted key is not valid an error message will be displayed " "during system configuration."

OSPFv3-3-IPSEC_POLICY_ALREADY_EXIST

3-Error

[chars] SPI [dec] is already in use with ospf

An attempt was made to use a SPI that has already been used.

-

"Choose a different SPI"

OSPFv3-3-IPSEC_POLICY_SPI_IN_USE

3-Error

[chars] SPI [dec] is already in use by a process other than ospf

An attempt was made to use a SPI that has already been used.

-

"Choose a different SPI. Enter the <CmdBold>show crypto ipv6 " "ipsec sa<NoCmdBold> command to view a list of SPIs that are " "already being used."

OSPFv3-3-IPSEC_POLICY_SPI_REUSE

3-Error

[chars] [chars] is already configured with SPI [dec].

An attempt was made to use a SPI that has already been used

-

"Unconfigure the SPI first or choose a different one."

OSPFv3-3-IPSEC_POLICY_INVALID_KEY_LEN

3-Error

[chars] The key length used with SPI [dec] is not valid

The key length was incorrect.

-

"Choose a valid IPsec key. An IPsec authentication key must be " "32MD5 or 40SHA-1 hexidecimal digits long."

OSPFv3-3-IPSEC_CREATE_POLICY_ERROR

3-Error

[chars] [chars] error occured when attempting to create an IPsec policy for SPI [dec]

An IPsec API error occurred. This message indicates an internal error

-

LOG_STD_RECUR_ACTION

OSPFv3-3-IPSEC_POLICY_NOT_EXIST

3-Error

SPI [dec] is not being used by ospf process [chars].

An attempt was made to unconfigure a SPI that is not being used with OSPFv3.

-

"Enter a show command to see which SPIs are used by OSPFv3"

OSPFv3-3-IPSEC_POLICY_STILL_IN_USE

3-Error

[chars] The policy for SPI [dec] could not be removed because it is in use.

An attempt was made to remove the policy for the indicated SPI but the policy was still being used by a secure socket.

-

LOG_STD_NO_ACTION

OSPFv3-3-IPSEC_REMOVE_POLICY_ERROR

3-Error

[chars] [chars] error occured when attemtping to remove the IPsec policy with SPI [dec]

An IPsec API error occurred. This message indicates an internal error

-

LOG_STD_RECUR_ACTION

OSPFv3-3-IPSEC_CLOSE_SS_ERROR

3-Error

[chars] Unable to close secure socket with SPI [dec] on interface [chars]

An IPsec API error occurred. This message indicates an internal error

-

LOG_STD_RECUR_ACTION

OSPFv3-3-IPSEC_REGISTER_CLIENT

3-Error

OSPFv3 was unable to register with IPsec

An internal error occurred.

-

LOG_STD_SH_TECH_ACTION

OSPFv3-3-IPSEC_GENERAL_ERROR

3-Error

IPsec reported a GENERAL ERROR: message [chars] count [dec]

An internal error occurred.

-

LOG_STD_SH_TECH_ACTION

OSPFv3-3-IPSEC_ERROR_MSG_RETRY

3-Error

[chars] IPsec sent a [chars] message [chars] to OSPFv3 for interface [chars]. Recovery attempt [dec]

An internal error occurred. The system is attempting to re-open the secure socket.

-

"The system is attempting to recover. No action needs to be taken."

OSPFv3-3-IPSEC_ERROR_MSG_ABORT

3-Error

[chars] IPsec sent a [chars] message [chars] to OSPFv3 for interface [chars]. Recovery aborted

An internal software error has occurred. The maximum number of recovery attempts have been exceeded.

-

LOG_STD_SH_TECH_ACTION

OSPFv3-3-NO_SNMP_IFINDEX

3-Error

Interface [chars] does not have an SNMP MIB ifIndex and has been disabled

The OSPF process has been configured to use the SNMP MIB ifIndex\n\ valuefor the interface IDs. However the ifIndex is not set on this\n\ interface so the interface can not be enabled.

-

"Unconfigure interface-id snmp-if-index for this OSPF process"

OSPFv3-4-NO_OUTPUTQ

4-Warning

[chars] Packet not written to the output queue

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-4-UNREC_TIMER

4-Warning

[chars] Unrecognized timer [dec] in OSPF [chars]

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-4-DB_NOT_FOUND

4-Warning

[chars] Can't find LSA database type [hec] area [chars] interface [chars]

An internal error occured.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-4-DBD_ALLOC_FAIL

4-Warning

[chars] Could not allocate DBD packet

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-4-INV_LSA_BLD_FLG

4-Warning

[chars] Invalid build flag [hec] for LSA [inet] type 0x[hec]

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-6-UNREC_VIRT_INT_TYPE

6-Information

Unrecognized virtual interface [chars]. Treat it as loopback stub route

The virtual interface type was not recognized by OSPFv3 so it will be treated as a loopback interface stub route.

ospf

LOG_STD_NO_ACTION

OSPFv3-4-ASBR_WITHOUT_VALID_AREA

4-Warning

Router [chars] is currently an ASBR while having only one area which is a stub area

An ASBR must be attached to an area which can carry AS External or NSSA LSAs

ospf

"Make the area to which the router is attached into an NSSA " "or regular area."

OSPFv3-4-NO_GLOBAL_ADDR

4-Warning

[chars] Could not select a global IPv6 address. Virtual links require at least one global IPv6 address.

A virtual link was configured. For the virtual link to function a global IPv6 address must be available. However no global IPv6 address could be found on the router.

ospf

"Configure a global IPv6 address on an interface on this router."

OSPFv3-3-INT_INIT_FAILED

3-Error

[chars] Init failed for interface [chars] [chars].

The interface initialization failed. Possible reasons: 1 The area to which the interface is being attached is being

ospf

"Remove the configuration command that covers the interface " "and then try it again. " LOG_STD_RECUR_ACTION

OSPFv3-3-INT_ATTACHED_MULTI_AREAS

3-Error

[chars] Interface [chars] is attached to more than one area

The interface is on the interface list for an area other than the one which the interface links to.

ospf

LOG_STD_SH_TECH_ACTION

OSPFv3-3-CFG_NBR_ALLOC_FAILED

3-Error

[chars] Could not allocate or find the neighbor

An internal error occurred.

ospf

LOG_STD_ACTION

OSPFv3-4-INVALID_METRIC

4-Warning

[chars] Area [chars]: Router [inet] originating invalid type 0x[hec] LSA ID [dec] Metric [dec] on Link ID [dec] Link Type [dec]

The router indicated in this message has originated an LSA with invalid metric. If this is an router LSA and link metric is zero there's a risk of routing loops and traffic loss in the network

ospf

"Configure valid metric for given LSA type and link type on " "the router originating reported LSA"

OSPFv3-6-INPUT_TO_BE_DEPRECATED

6-Information

[chars] will be deprecated

The value will be deprecated in a future version

ospf

"Refer to current command reference"

OSPFv3-6-UNPROCESSED_IPV4_CALLBACK

6-Information

IPv4 process call ignored.

An internal error occurred.

ospf

LOG_STD_ACTION

OSPFv3-3-CFG_OSPF_FAILED

3-Error

Only [dec] OSPFv3 process is allowed

The maximum number of OSPFv3 instances permitted for this IOS image has been reached

-

"Upgrade to an unrestricted IOS image"

OSPFv3-4-MAX_LSA_LIM

4-Warning

[chars] Maximum number of non self-generated LSA has been exceeded - [dec] LSAs

Maximum number of non self-generated LSA has been exceeded

ospf

"Check if some router in the network is generating large number of " "LSAs as a result of misconfiguration"

OSPFv3-4-MAX_LSA_THR

4-Warning

[chars] Threshold for maximum number of non self-generated LSA has been reached - [dec] LSAs

Threshold for maximum number of non self-generated LSA has been reached

ospf

"Check if some router in the network is generating large number of " "LSAs as a result of misconfiguration"

OSPFv3-4-NSSA_NO_FA

4-Warning

[chars] Process lacks forwarding address for type 7 LSA [inet] in NSSA [chars] - P-bit cleared

There is no viable forwarding address in the NSSA area. Hence the P-bit must be cleared and the type 7 LSA will not be translated to a type 5 LSA by the NSSA translator. Refer to RFC 3101.

ospf

"Configure at least one interface in the NSSA with " "an advertised IPv4 for IPv4 address family or IPv6 global "

OSPFv3-6-SHUTDOWN_START

6-Information

[chars] Shutdown started

OSPFv3 process has started the shutdown procedure. Another message will be logged when it completes.

-

"Wait for shutdown to complete."

OSPFv3-6-SHUTDOWN_COMPLETE

6-Information

[chars] Shutdown completed

OSPFv3 process has finished the shutdown procedure.

-

LOG_STD_NO_ACTION

OSPFv3-6-DFT_OPT

6-Information

Protocol timers for fast convergence are [chars].

Routing-default-optimize state

ospf

LOG_STD_ACTION

OSPFv3-6-NSF_START

6-Information

OSPFv3-[dec] NSF started

NSF start notification

ospf

LOG_STD_NO_ACTION

OSPFv3-6-NSF_COMPLETE

6-Information

OSPFv3-[dec] NSF completed

NSF completed notification

ospf

LOG_STD_NO_ACTION

OSPFv3-6-NSF_TERMINATE

6-Information

OSPFv3-[dec] NSF terminated

NSF terminated notification

ospf

LOG_STD_NO_ACTION

OSPF-3-CF_NOMEM

3-Error

Unable to allocate checkpoint buffer: [chars]

NSR operation may be degraded to a lack of memory.

ospf

show tech-support ospf

OSPF-3-CF_NOMSG

3-Error

No space in checkpoint buffer

NSR operation may be degraded to a lack of memory.

ospf

show tech-support ospf

OSPF-4-CF_UNKNOWN_STATUS

4-Warning

Unknown checkpoint status: [dec]

An internal error occured.

ospf

show tech-support ospf

OSPF-4-CHKPT_UNKNOWN_TYPE

4-Warning

Invalid checkpoint message type: [dec]

An internal error occurred.

ospf

show tech-support ospf

OSPF-3-CHKPT_NOMEM

3-Error

Unable to allocate checkpoint queue entry

NSR will not operate due to a failure communicating with the standby.

ospf

show tech-support ospf

OSPF-3-CHKPT_SEND_FAIL

3-Error

Checkpoint message send failed: [chars]

NSR will not operate due to a failure communicating with the standby.

ospf

show tech-support ospf

OSPF-3-CHKPT_IDB_ENCODE_FAIL

3-Error

Interface [chars] cannot be encoded for NSR

Adjacency and interface information learned from this interface cannot be checkpointed due to an interface encoding error.

ospf

"Please verify that this interface type is supported for NSR in " "this release. If so report the problem to the TAC."

OSPF-3-CHKPT_IDB_DECODE_FAIL

3-Error

Interface cannot be decoded for NSR: [chars]

Adjacency and interface information for an interface cannot be checkpointed due to an interface decoding error.

ospf

"Please verify that this interface type is supported for NSR in " "this release. If so report the problem to the TAC."

OSPF-3-CHKPT_MSG

3-Error

Invalid checkpoint message: [chars] [chars]

NSR will not operate due to an error in a checkpoint message.

ospf

show tech-support ospf

OSPF-4-CHKPT_MSG_SEQ

4-Warning

Invalid checkpoint message sequence number: received [dec] expected [dec]

NSR has detected a duplicate checkpoint message.

ospf

show tech-support ospf

OSPF-3-CHKPT_MSG_LOST

3-Error

Checkpoint message lost

NSR will not operate due to a dropped checkpoint message.

ospf

show tech-support ospf

OSPF-3-CHKPT_STATUS_LOST

3-Error

Checkpoint status lost

NSR will not operate due to a missing checkpoint status message.

ospf

show tech-support ospf

OSPF-3-CHKPT_STBY_NO_LSA_BUFFER

3-Error

Standby synchronization error: no LSA buffer

NSR will not operate due to an internal error.

ospf

show tech-support ospf

OSPF-3-CHKPT_STBY_LSDB_INVALID

3-Error

Standby link-state database validation failed expected/found count: [dec]/[dec] chksum: 0x%llx/0x%llx

NSR will not operate due to an error on the standby.

ospf

show tech-support ospf

OSPF-3-CHKPT_STBY_NO_NBR

3-Error

Standby synchronization error: could not find neighbor [chars] [inet] [inet]

NSR will not operate due to an internal error.

ospf

show tech-support ospf

OSPF-3-CHKPT_STBY_NO_NBR_IF

3-Error

Standby synchronization error: interface not attached to add neighbor [chars] [inet] [inet]

NSR will not operate due to an internal error.

ospf

show tech-support ospf

OSPF-3-CHKPT_STBY_NO_LSDB

3-Error

Standby synchronization error: could not add lsa type [dec]

NSR will not operate due to an internal error.

ospf

show tech-support ospf

OSPF-3-CHKPT_STBY_SYNC_LOST

3-Error

Standby synchronization lost for OSPF-[dec] was: [chars]

Synchronization between the active and standby OSPF has been lost.

ospf

show tech-support ospf

OSPF-3-ISSU_NEGOTIATION

3-Error

ISSU negotiation[chars] error: [dec] [chars]

The OSPF ISSU session could not complete negotiation. This failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ospf

LOG_STD_ACTION

OSPF-3-NSR_FAILED

3-Error

NSR can not recover checkpointed data for process [dec]

An NSR failover could not be performed because OSPF on the standby was not synchronized

ospf

show tech-support ospf

OSPF-3-NOSTART

3-Error

Unable to start OSPF: [chars]

An internal software error occurred.

ospf

LOG_STD_ACTION

OSPF-3-INTERNALERR

3-Error

Internal error: [chars]

An internal software error occurred.

ospf

LOG_STD_ACTION

OSPF-3-NOBACKBONE

3-Error

Flagged as being an ABR without a backbone area

The router was flagged as an Area Border Router ABR without backbone

ospf

"Restart the OSPF process."

OSPF-6-BADCHKSUM

6-Information

Checksum Failure in database in area [chars]\n Link State Id [inet] Old Checksum [hex] New Checksum [hex]\n

OSPF has detected a checksum error in the database due to memory corruption.

ospf

"Restart OSPF process."

OSPF-4-ERRRCV

4-Warning

Received invalid packet: [chars] from [inet] [chars]

An invalid OSPF packet was received. Details are included in the error message. The cause might be a misconfigured OSPF or an internal error in the sender.

ospf

"Check the OSPF configuration of the receiver and the sender for " "inconsistency."

OSPF-5-LASTKEYEXP

5-Notice

The last key has expired for interface [chars] packets sent using last valid key.

None of the security associations have a lifetime that include the current system time.

ospf

"Configure a new security association or alter the lifetime of a " "current security association"

OSPF-4-NOVALIDKEY

4-Warning

No valid authentication [chars]key is available on interface [chars]

-

ospf

"Configure a new key"

OSPF-5-EXPIREDKEY

5-Notice

Packet [chars] on interface [chars] with expired Key ID [dec].

The Key ID in use has a lifetime and the system time is not within that lifetime

ospf

"Configure a new key"

OSPF-4-INVALIDKEY

4-Warning

Key ID [dec] [chars]on interface [chars]

The ID is not found in the configured key chain

ospf

"Configure a new security association with the Key ID"

OSPF-4-INVALIDKCNAME

4-Warning

Key chain name [chars] on [chars] is invalid

The key-chain name configured under OSPF interface does not match global key chain configuration.

ospf

"Fix configuration. Either remove ospf authentication command " "or configure key chain in global configuration mode."

OSPF-4-INVALIDKCKEYID

4-Warning

Key ID [dec] in key chain [chars] is invalid

They Key ID configured in the key chain is out of range for OSPF. This may happen because the key chain allows Key ID values outside of the range which is acceptable for OSPF.

ospf

"Configure a new security association with a Key ID that is in " "the range 1-255"

OSPF-5-NOKEY

5-Notice

Key ID [dec] in key chain [chars] does not have a key

OSPF has been configured to use cryptographic authentication however an key password has not been configured

ospf

"Configure a key for the security association"

OSPF-5-NOCRYPTOALG

5-Notice

Key ID [dec] in key chain [chars] does not have a cryptographic algorithm

OSPF has been configured to use cryptographic authentication however an algorithm has not been configured

ospf

"Configure a cryptographic-algorithm for the security association"

OSPF-4-NONEIGHBOR

4-Warning

Received [chars] from unknown neighbor [inet]

OSPF hello database description or database request packet was received but the router could not identify the sender.

ospf

"This situation should correct itself. " LOG_STD_RECUR_ACTION

OSPF-4-BADLENGTH

4-Warning

Invalid length [dec] in OSPF packet type [dec] from [inet] ID [inet] [chars]

The system received an OSPF packet with a length field of less than normal header size or inconsistent with the size of the IP packet in which it arrived. This indicates an error in the sender of the packet.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-4-BADLSATYPE

4-Warning

Invalid lsa: [chars] Type [dec] Length [dec] LSID [inet] from [inet] [inet] [chars]

The router received an LSA with invalid data. LSA contains invalid LSA type wrong checksum or wrong length. The cause is either memory corruption or unexpected behavior on a router.

ospf

"From a neighboring address locate the problem router. " "1 Collect a running configuration of the router by entering the"

OSPF-4-CONFLICTING_LSAID

4-Warning

Process [dec] area [chars]: LSA origination prevented by LSA with same LSID but a different mask\n Existing Type [dec] LSA: LSID [inet]%m\n New Destination: [inet]%m

An LSA origination was prevented by a conflicit with an existing\n LSA with the same LSID but a different mask. The algorithm in\n RFC 2328 Appendix E is used to resolve conflicts when multiple\n LSAs with the same prefix and differing masks are advertised.\n When using this algorithm and host routes are advertised there\n are situations where conflict resolution is impossible and either\n the host route or the conflicting prefix is not advertised.

ospf

"Locate the prefix that is not advertised and the conflicting prefix\n" "using <CmdBold>show ip route<NoCmdBold> and " "<CmdBold>show ip ospf database<NoCmdBold>.\n" "Decide which route or prefix is more important to advertise and take\n" "steps to prevent advertising the conflicting route or prefix.\n" "If you cannot determine the nature of the error from the collected\n\ information contact your Cisco technical support representative\n\ and provide the representative with the gathered information."

OSPF-4-NORTRID

4-Warning

OSPF process [dec] failed to allocate unique router-id and cannot start

OSPF failed while attempting to allocate a unique router-id from the IP addresses of its interfaces.

ospf

"Ensure that at least one interface is active up and has a valid IP "

OSPF-4-VIRTUAL_IN_NON_BACKBONE

4-Warning

Virtual link information found in non-backbone area: [chars]

An internal software error has caused this router to generate a Router LSA that has a virtual link in a non-backbone area.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-3-DBEXIST

3-Error

area [chars] lsid [inet] mask [inet] type [dec]

OSPF is trying to add existing LSA to the database.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-6-ZERO_BANDWIDTH

6-Information

interface [chars] has zero bandwidth

The interface has reported its bandwidth as zero.

ospf

LOG_STD_NO_ACTION

OSPF-5-ADJCHG

5-Notice

Process [dec] Nbr [inet] on [chars] from [chars] to [chars] [chars]

An OSPF neighbor has changed state. The message describes the change and the reason for it. This message appears only if the <Bold>log-adjacency-changes<NoBold> command is configured for the OSPF process.

ospf

LOG_STD_NO_ACTION

OSPF-6-AREACHG

6-Information

[inet]%m changed from area [chars] to area [chars]

An OSPF configuration change has caused a network range to change areas.

ospf

LOG_STD_NO_ACTION

OSPF-6-MODECHG

6-Information

Base topology enabled on interface [chars] attached to MTR compatible mode area [chars]

OSPF Interfaces attached to MTR compatible OSPF areas require the base topology to be enabled

ospf

LOG_STD_NO_ACTION

OSPF-4-DUP_RTRID_NBR

4-Warning

OSPF detected duplicate router-id [inet] from [inet] on interface [chars]

OSPF has received hello packet from a neighbor that has the same router ID as this routing process. A full adjacency cannot be established.

ospf

"The OSPF router ID should be unique. Change the router ID of the " "neighbor."

OSPF-4-DUP_RTRID_AREA

4-Warning

Detected router with duplicate router ID [inet] in area [chars]

OSPF has detected a router in the area that has the same router ID as this routing process. Duplicate router IDs may result in network instability causing some destinations to be unreachable.

ospf

"The OSPF router ID should be unique. Make sure all routers in the " "area have unique router ID."

OSPF-4-NET_TYPE_MISMATCH

4-Warning

Received Hello from [inet] on [chars] indicating a potential \n\ network type mismatch

OSPF received hello packet from a neighbor which has a non-zero \n\ value in the DR or BDR field but this router is configured as \n\ point-to-point on this interface. This indicates a network type \n\ mismatch.

-

"The network type must be configured the same for all devices \n\ attached to the same link."

OSPF-4-FLOOD_WAR

4-Warning

Process [dec] [chars] LSA ID [inet] type-[dec] adv-rtr [inet] in area [chars]

Router is extensively re-originating or flushing the LSA reported by this error message

ospf

"If this router is flushing the network LSA it means the " "router received a network LSA whose LSA ID conflicts with " "the IP address of one of the router's interfaces and flushed " "the LSA out of the network. For OSPF to function correctly " "the IP addresses of transit networks must be unique. " "Conflicting routers are the router reporting this error " "message and the router with the OSPF router ID reported as " "adv-rtr in this message. " "If this router is re-originating an LSA highly probably some " "other router is flushing this LSA out of the network. Find " "that router and avoid the conflict. Conflict for type-2 LSA " "may be due to duplicate LSA ID for type-5 LSA it may be " "duplicate router-id on the router reporting this error message" " and on the routers connected to the different area." "In an unstable network this message may also warn of " "extensive re-origination of LSA for some other reason. " "Contact your Cisco technical support representative " "to investigate such a case."

OSPF-3-RECONF_VL

3-Error

OSPF process [dec] is changing router-id. Reconfigure virtual link neighbors with our new router-id

OSPF process is being reset and it is going to select a new router-id. This will bring down all virtual links. To make them work again virtual link configuration needs to be changed on all virtual link neighbors.

ospf

"Change virtual link configuration on all the virtual link " "neighbors to reflect our new router-id."

OSPF-3-LSA_LEN

3-Error

Area [chars] router-LSA of length [dec] bytes plus update overhead bytes is too large to flood.

The router tried to build a router-LSA which is larger than the huge system buffer size or the OSPF protocol imposed maximum.

ospf

"If the reported total length LSA size plus " "overhead is larger than the huge system "

OSPF-4-BADLSAMASK

4-Warning

Bad LSA mask: Type [dec] LSID [inet] Mask [inet] from [inet] \n NOTE: This route will not be installed in the routing table.

The router received an LSA with an invalid LSA mask. The cause is likely due to wrong configuration from the LSA originator.

ospf

"Find the originating router of this LSA with bad mask correct " "any misconfiguration of this LSA's network. For further debugging " "call your Cisco technical support representative for assistance."

OSPF-4-OSPF_MAX_LSA

4-Warning

Maximum number of non self-generated LSA has been exceeded \ospf [dec]\ - [dec] LSAs

Maximum number of non self-generated LSA has been exceeded

ospf

"Check if some router in the network is " "generating large number of LSAs as a result " "of misconfiguration"

OSPF-4-OSPF_MAX_LSA_THR

4-Warning

Threshold for maximum number of non self-generated LSA has been reached \ospf [dec]\ - [dec] LSAs

Threshold for maximum number of non self-generated LSA has been reached

ospf

"Check if some router in the network is " "generating large number of LSAs as a result " "of misconfiguration"

OSPF-3-NO_SNMP_IFINDEX

3-Error

Interface [chars] does not have an SNMP MIB ifIndex and has been disabled

The OSPF process has been configured to use the SNMP MIB ifIndex value for the interface IDs. However the ifIndex is not set on this interface so the interface can not be enabled.

ospf

"Unconfigure interface-id snmp-if-index for this OSPF process"

OSPF-4-NO_OUTPUTQ

4-Warning

Packet not written to the output queue

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-4-UNREC_TIMER

4-Warning

Unrecognized timer [dec] in OSPF [chars]

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-4-INV_LSA_BLD_FLG

4-Warning

Invalid build flag [hec] for LSA [inet] type [dec]

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-4-AREA_ALLOC_FAIL

4-Warning

Can not allocate memory for area structure

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-6-PROC_REM_FROM_INT

6-Information

OSPF process [dec] removed from interface [chars]

The OSPF process was removed from the interface due to IP VRF removal.

ospf

LOG_STD_NO_ACTION

OSPF-6-UNREC_VIRT_INT_TYPE

6-Information

Unrecognized virtual interface [chars]. Treat it as loopback stub route

The virtual interface type was not recognized by OSPF so it will be treated as a loopback interface stub route.

ospf

LOG_STD_NO_ACTION

OSPF-4-RTRID_IN_USE

4-Warning

Router-ID [inet] is in use by ospf process [dec]

Attempted to assign a Router ID which is in use by another process

ospf

"Configure another Router ID for one of the " "processes."

OSPF-4-ASBR_WITHOUT_VALID_AREA

4-Warning

Router is currently an ASBR while having only one area which is a stub area

An ASBR must be attached to an area which can carry AS External or NSSA LSAs

ospf

"Make the area to which the router is attached into an NSSA or " "regular area."

OSPF-4-NO_IPADDRESS_ON_INT

4-Warning

No IP address for interface [chars]

Interface is not point-to-point and is unnumbered

ospf

"Change interface type or give the interface an IP address"

OSPF-3-INT_INIT_FAILED

3-Error

Init failed for interface [chars] [chars].

The interface initialization failed. Possible reasons: 1 The area to which the interface is being attached is being

ospf

"Remove the configuration command that covers the interface " "and then try it again. " LOG_STD_RECUR_ACTION

OSPF-3-INT_ATTACHED_MULTI_AREAS

3-Error

Interface [chars] is attached to more than one area

The interface is on the interface list for an area other than the one which the interface links to.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-3-CFG_NBR_ALLOC_FAILED

3-Error

Could not find or allocate neighbor [inet]

An internal error occurred.

ospf

LOG_STD_ACTION

OSPF-4-CFG_NBR_INVALID_NET_TYPE

4-Warning

Can not use configured neighbor [inet] on [chars]. Neighbor command only allowed on NBMA and P2MP networks

The configured neighbor was found on a network for which the network type was neither NBMA nor point-to-multipoint

ospf

LOG_STD_NO_ACTION

OSPF-4-CFG_NBR_INVALID_OPT_ON_P2MP

4-Warning

Can not use configured neighbor [inet] on [chars]. Cost or database-filter is required

The configured neighbor was found on a point-to-multipoint broadcast network. Either the cost or database-filter option needs to be configured.

ospf

"Check the configuration options for the neighbor command and correct " "the options or the network type for the neighbor's interface."

OSPF-4-CFG_NBR_INVALID_OPT_ON_P2MP_NB

4-Warning

Can not use configured neighbor [inet] on [chars] for topology [chars]. Neighbor needs to be configured under base topology

The configured neighbor was found on a point-to-multipoint non-broadcast network for a non-base topology. Neighbor needs to be configured under base topology.

ospf

"Check the configuration options for the neighbor command and correct " "the options or the network type for the neighbor's interface."

OSPF-4-CFG_NBR_INVALID_OPT_ON_NBMA

4-Warning

Can not use configured neighbor [inet] on [chars] for topology [chars]. Neighbor command only allowed on P2MP network for non-base topology

The configured neighbor was found on a NBMA network for a non-base topology. Neighbor can not be configured under this topology.

ospf

"Check the configuration for the neighbor command and correct it" "or change the network type for the neighbor's interface."

OSPF-4-CFG_NBR_DEFAULT_OPT_ON_P2MP

4-Warning

[chars] Configured neighbor [inet] - Ignore incompatible configured options use default. Allowed options on P2MP interfaces are cost and database-filter

The configured neighbor was found on a point-to-multipoint network and either the poll-interval or priority option was configured. These options are only allowed on NBMA type networks.

ospf

"Check the configuration options for the neighbor command and correct " "the options or the network type for the neighbor's interface."

OSPF-4-CFG_NBR_DEFAULT_OPT_ON_NBMA

4-Warning

[chars] Configured neighbor [inet] - Ignore incompatible configured options use default. Allowed options on NBMA interfaces are poll-interval and priority

The configured neighbor was found on a NBMA network and either the cost or database-filter option was configured. These options are only allowed on point-to-multipoint type networks.

ospf

"Check the configuration options for the neighbor command and correct " "the options or the network type for the neighbor's interface."

OSPF-4-INVALID_METRIC

4-Warning

OSPF-[dec] Area [chars]: Router [inet] originating invalid type [dec] LSA ID [inet] Metric [dec] on Link ID [inet] Link Type [dec]

The router indicated in this message has originated an LSA with invalid metric. If this is an router LSA and link metric is zero there's a risk of routing loops and traffic loss in the network

ospf

"Configure valid metric for given LSA type and link type on " "the router originating reported LSA"

OSPF-6-BAD_LSA_COUNT

6-Information

OSPF-[dec] Area [chars]: LSA ID [inet] Type [dec] Adv-rtr [inet] LSA counter [chars]

An internal error has been self corrected. There's no operational impact related to this error message.

ospf

show tech-support ospf

OSPF-4-NSSA_NO_FA

4-Warning

OSPF process [dec] lacks forwarding address for type 7 LSA [inet] in NSSA [chars] - P-bit cleared

There is no viable forwarding address in the NSSA area. Hence the P-bit must be cleared and the type 7 LSA will not be translated to a type 5 LSA by the NSSA translator. Refer to RFC 3101.

ospf

"Configure at least one interface in the NSSA with " "an advertised IP address. A loopback is preferable " "since advertisement will not be dependent on the " "underlying layer 2 state."

OSPF-6-RTR_WRONG_REFCNT

6-Information

OSPF-[dec] Invalid reference count for [inet]

Negative database reference count

ospf

show tech-support ospf

OSPF-3-BAD_LSA_BUILD

3-Error

OSPF-[dec]: Bad build request for LSA type [dec] LSID [inet] mask [inet]

LSA was not originated due to internal software error

ospf

show tech-support ospf

OSPF-3-CFG_OSPF_FAILED

3-Error

Only [dec] OSPF process is allowed

The limit of number of allowed OSPF instances has reached

ospf

"Don't configure more than allowed instances"

OSPF-4-SR_APP_REG_FAIL

4-Warning

[chars] failed to register with SR_APP with error [dec]

OSPF process registration with SR APP failed.

ospf

"Reconfigure segment routing and Restart OSPF process."

OSPF-4-SR_MFI_REG_FAIL

4-Warning

[chars] failed to register with MFI with error [dec]

Disable/Re-Enable segment-routnig in this OSPF Process.

ospf

"Disable/Re-Enable segment-routing in this OSPF process."

OSPF-4-SR_APP_GET_ATTR_FAIL

4-Warning

[chars] failed to get SR attributes from SR_APP with error [dec]

OSPF process failed to get SR attributes.

ospf

"Reconfigure segment routing attributes."

OSPF-6-SRMS_DB_FREE

6-Information

[chars] LSA [dec]/[inet]/[inet] freed while linked to srms entry [inet]/[dec] range [dec]

OSPF process free LSA which is still linked to SRMS. \n Necessary actions has been taken and message has no functional impact

ospf

"Contact your Cisco technical support representative."

OSPF-6-DFT_OPT

6-Information

Protocol timers for fast convergence are [chars].

Routing-default-optimize state

ospf

LOG_STD_ACTION

OSPF-6-NSF_START

6-Information

OSPF-[dec] NSF started

NSF start notification

ospf

LOG_STD_NO_ACTION

OSPF-6-NSF_COMPLETE

6-Information

OSPF-[dec] NSF completed

NSF completed notification

ospf

LOG_STD_NO_ACTION

OSPF-6-NSF_TERMINATE

6-Information

OSPF-[dec] NSF terminated

NSF terminated notification

ospf

LOG_STD_NO_ACTION

OSPF-6-DISTLS_DUPID

6-Information

OSPF-[dec] is already using Link state distribution instance [dec]. Please configure a unique value

Link state distribution instance-id should be unique across all OSPF instances

ospf

LOG_STD_NO_ACTION

OSPF_NSR-3-CF_ADD_CLIENT

3-Error

Error adding OSPF checkpoint client: [chars]

OSPF was not able to register as a client of the checkpoint facility

ospf

show tech-support ospf

OSPF_NSR-3-CF_NOMEM

3-Error

Unable to allocate checkpoint buffer: [chars]

NSR operation may be degraded to a lack of memory.

ospf

show tech-support ospf

OSPF_NSR-3-CF_NOMSG

3-Error

No space in checkpoint buffer

NSR operation may be degraded to a lack of memory.

ospf

show tech-support ospf

OSPF_NSR-3-CHKPT_MSG

3-Error

Invalid checkpoint message: [chars] [chars]

NSR will not operate due to an error in a checkpoint message.

ospf

show tech-support ospf

OSPF_NSR-2-ISSU_INIT

2-Critical

ISSU client initialization failed to [chars] error: [dec] [chars]

The OSPF ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ospf

LOG_STD_ACTION

OSPF_NSR-3-ISSU_SESSION_UNREGISTR

3-Error

OSPF[chars] ISSU client failed to unregister session information error: [dec] [chars]

The OSPF ISSU client failed to unregister session information.

ospf

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

OSPF_NSR-3-ISSU_TRANSFORM_FAIL

3-Error

OSPF[chars] ISSU client [chars] transform failed for message type [dec] [chars]: [dec] [chars]

The OSPF ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Archive state between the active device and the standby device is not identical.

ospf

"show issu session <client_id> and " "show issu negotiated version <session_id>"

OSPF_NSR-3-ISSU_MSG_SIZE

3-Error

OSPF[chars] ISSU client failed to get the MTU for message type [chars] [dec]:

The OSPF ISSU client failed to calculate the MTU for the specified message. The OSPF ISSU client is not able to send the message to the standby device.

ospf

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

OSPF-4-NULL_LINKAGE

4-Warning

Doubly linked list linkage is NULL

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-4-NULL_PREV_LINKAGE

4-Warning

Doubly linked list prev linkage is NULL [hec]

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-3-NOSELF

3-Error

[chars] iterface [chars] interface state [dec]

An internal error occurred.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-3-UNKNOWNSTATE

3-Error

Reached unknown state in neighbor state machine

An internal software error in this router has resulted in an invalid neighbor state during database exchange.

ospf

LOG_STD_SH_TECH_ACTION

OSPF-6-LRIB_WRONG_REFCNT

6-Information

[chars] Invalid reference count for [chars]

Negative database reference count

ospf

show tech-support ospf

IPRT-3-NOMEMORY

3-Error

No memory available for [chars]

The requested operation failed because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPRT-2-COMPRESS

2-Critical

Bad route_compress call sdb= [hec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

IPRT-3-PATHIDX

3-Error

Bad path pointer of [hec] for [inet] [dec] max

A software error occurred.

-

LOG_STD_ACTION

IPRT-3-BADCOMLIST

3-Error

Community list check with bad list [dec]

A user specified an invalid BGP community list number.

-

"Check the system configuration to make sure that the community list " "specified falls within the valid range."

IPRT-3-IPTABLEINIT

3-Error

IP routing table creation failure - [chars]

An internal software error occurred preventing the creation of new IP routing table.

-

"Copy the message exactly as it appears and report it to your " "technical support representative."

IPRT-3-RIB_ACC_HDLR_INIT

3-Error

Error Registering [chars] RIB handlers with RIB Access Infra

An internal software error occurred preventing Access to RIB Data.

ribinfra

"Copy the message exactly as it appears and report it to your " "technical support representative."

IPRT-4-REDIST_MAX_PFX

4-Warning

Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes

We have reached the maximum number of redistributed prefixes

-

"Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake"

IPRT-4-REDIST_THR_PFX

4-Warning

Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes

We have reached the threshold level of number of redistributed prefixes

-

"Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake"

IPRT-3-ROUTELIMITWARNING

3-Error

IP routing table limit warning - [chars]

The number of routes in the named IP routing table has reached the configured warning limit.

-

"Reduce the number of routes in the table or reconfigure the limit"

IPRT-3-ROUTELIMITEXCEEDED

3-Error

IP routing table limit exceeded - [chars]

The number of routes in the named IP routing table has reached the configured limit. No further routes will be added to the table

-

"Reduce the number of routes in the table or reconfigure the limit"

IPRT-4-ROUTECOUNTNEGATIVE

4-Warning

IP route counter negative - [chars] [inet] Attempt: [dec]

Attempt to decrement IP route counter into negative value

ribinfra

"Use "clear ip route *" command to reset the route counter. If " "the message still comes out consistently copy the messages exactly " "as they appear and report it to your technical support " "representative."

IPRT-4-BADRIBDB

4-Warning

Attempt to remove a next hop from the wrong table. Attempted: [chars] should be: [chars] prefix: [inet]

Attempt to remove a next hop from the wrong routing table

-

LOG_STD_RECUR_ACTION

IPRT-4-BADTRACKOBJECTTYPE

4-Warning

can't track this type of object

Route maps only support STATE type track objects. This object is not a STATE object

-

"Reconfigure the track object to make it a STATE object."

IPRT-6-STATICROUTESACROSSVRF

6-Information

Un-installing static route [inet]%m from [chars] routing table with outgoing interface [chars]

Restricting the access of static routes that point across vrfs

-

"Remove the static routes that are pointing accross VRF interfaces"

IPRT-6-STATICROUTESACROSSTOPO

6-Information

Cannot install inter- topology static route [inet]%m topology [chars] on outgoing interface [chars]

Restricting the access of static routes that point across topologies

-

"Remove the static routes that are pointing accross topology interfaces"

IPRT-3-BADRFREG

3-Error

Unable to register IP Routing as a client of RF.

This is a severe error as far as IP routing NSF is concerned

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IPRT-2-IPTABLEERROR

2-Critical

IP routing table [chars] initialization failure - [chars]

An internal software error occurred preventing the creation of new IP routing table.

-

"Copy the message exactly as it appears and report it to your " "technical support representative."

IPRT-3-RIBTABLEERROR

3-Error

RIB error [dec] on [chars] - [chars]

An internal software error occurred processing an event associated with a routing table.

-

"Copy the message exactly as it appears and report it to your " "technical support representative."

IPRT-4-RWATCH_BFDNEIGHBOR_CREATE_ERROR

4-Warning

RIB Rwatch failed to create bfd neighbor session proctype [dec] src_topoid [hec] dst_topoid [hec] [chars][chars][chars] neighbor [chars]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-4-RWATCH_UPCALL_INIT_ERROR

4-Warning

RIB Rwatch failed to initialize the upcall table afi [dec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-4-RWATCH_BFDNEIGHBOR_SESS_WAVL_INSERT_ERROR

4-Warning

RIB Rwatch failed to insert bfd neighbor session into WAVL tree proctype [dec] topoid [hec] [chars] neighbor [chars]

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-4-RWATCH_NEIGHBOR_WAVL_DELETE_ERROR

4-Warning

RIB Rwatch neighbor not found in WAVL tree for deletion client : [chars] topoid : [hec] interface : [chars] binding label: [chars] address : [chars]

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-4-RWATCH_TRKSN_DELETE_ERROR

4-Warning

RIB Rwatch tracked sequence number [dec] not found for client : [chars] topoid : [hec] prefix : [chars] prefix_len : [dec]

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-3-VIAUPD_ERROR

3-Error

Error [dec] inserting additional path for [inet]%m via [inet]%m

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-VIAUPD_ALLOC_ERROR

3-Error

Error allocating [dec] next hops for [inet]%m via [inet]%m

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NOTSAMEOWNER

3-Error

SAME_PROTO dist_status [dec] from [chars] for route owned by [chars]

-

-

-

IPRT-3-NO_PDB_INDEX

3-Error

Pdb index not available for [chars]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-BAD_PDB_HANDLE

3-Error

Pdb handle error %04x %04x [hec] %08x %04x %02x

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NO_RIB_TABLE

3-Error

RIB table lookup failure: [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-PDB_DEL_ERROR

3-Error

Pdb delete error [chars] [hec] [hec] [hec] [hec] [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-IPDB_DEL_ERROR

3-Error

i_pdb delete error [chars] [hec] [hec] [hec] [hec] [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-BAD_PDB_INDEX

3-Error

Pdb index error %08x %04x [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NULL_NDB

3-Error

Unexpected null NDB

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NULL_NDBSHR

3-Error

Unexpected null NDBSHR [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_BAD_MAGIC

3-Error

Bad magic for NDB structure [hec]/[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-CSB_SAVE_DATA_BAD_MAGIC

3-Error

Bad magic for CSB Data [hec]

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-3-NDBSHR_BAD_MAGIC

3-Error

Bad magic for NDBSHR structure [hec]/[hec]/[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NULL_RDB

3-Error

Unexpected null RDB

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NULL_RDBSHR

3-Error

Unexpected null RDBSHR [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-RDB_BAD_MAGIC

3-Error

Bad magic for RDB structure [hec]/[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-RDBSHR_BAD_MAGIC

3-Error

Bad magic for RDBSHR structure [hec]/[hec]/[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-GETEACHROUTE_BAD_MAGIC

3-Error

Bad magic for ip_geteachroute

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-ROUTEINSERTERROR

3-Error

Error inserting routing entry [inet]%m into IP [chars] routing table

An error has occurred when a routing entry was being inserted into the IP routing table.

-

LOG_STD_RECUR_ACTION

IPRT-3-ROUTEREPLACEERROR

3-Error

Error replacing route to [inet]%m with better route in IP [chars] routing table

Copy the message exactly as it appears and report it to your technical support representative.

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_ONQ

3-Error

Queue elem on queue - [inet]%m

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_NRP_IN_PROGRESS

3-Error

Invalid action on NDB while in NRP in progress: [chars] 0x[hec] [inet]%m state [dec] flags [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_STATE_ERROR

3-Error

NDB state error [chars] 0x[hec] [inet]%m state [dec] event [hec]->[hec] nh_type [hec] flags [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-4-NDB_STATE_CHANGE

4-Warning

NDB state change: [inet]%m [hec]->[hec] [dec]->[dec] [hec] refcnt [dec] tid [dec] cnt [dec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_REPLIC_INVALID_OP

3-Error

Invalid operation on replicated NDB [chars]:

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-4-INVALID_NRP_CONTEXT

4-Warning

Invalid context type: [dec] state: [dec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-4-RECURSIVE_ERASE

4-Warning

Recursive erase [dec] [hec]/[hec] [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NO_BACKUP_MEM

3-Error

No Backup Route memory available for [chars]

The addition of a Backup Route failed because of a low memory condition. Backup may not be available if the Primary Route is removed

-

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPRT-3-NO_REPLIC_MEM

3-Error

No Route Replication memory available for [inet]%m

The replication of a Route failed because of a low memory condition. The route will not be replicated in the destination table at this time.

-

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPRT-3-NEXTHOPS_LIST_ERROR

3-Error

[chars]: [inet]%m [dec] [hec] [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NEXTHOPS_LIST_MISMATCH

3-Error

[chars]: [chars] [inet]%m nhtype: [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-BAD_MSGTYPE_ERROR

3-Error

ION RIB error: [chars] [dec]/[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-4-RIB_DEBUG_ERROR

4-Warning

Generic RIB error: [hec] [hec] [hec] [hec] [hec] [hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-4-RIB_DELETE_PENDING_ERROR

4-Warning

RIB Marked Delete Pending in wrong state: [hec] [dec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-INVALIDTOPO

3-Error

Bad topology [chars] table in static routing entry [inet]%m

An error has occurred when a static route failed to find corresponding topology routing table.

-

LOG_STD_RECUR_ACTION

IPRT-6-DELETEINGTOP

6-Information

topology [chars] is deleting in static routing entry [inet]%m

A static route found a corresponding deleting topology routing table.

-

"The action is not taken due to topology deleting state"

IPRT-3-INVALIDVRF_BFD

3-Error

Bad vrf_id 0x[hec] in static BFD neighbor [chars] [inet]

A static BFD neighbor failed to find corresponding vrf.

-

LOG_STD_RECUR_ACTION

IPRT-3-NOTREG_BFD

3-Error

Unexpected reachability notification: [chars] [chars] [inet]

Gateway is not tracked by BFD.

-

LOG_STD_RECUR_ACTION

IPRT-3-NOTEXIST_BFD

3-Error

Static BFD neighbor does not exist: [chars] [chars] [inet]

Failed to find corresponding static BFD neighbor.

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICROUTES_TOPOLOCK

3-Error

Unable to lock topology [chars] table in static route

An error has occurred when a static route failed to lock corresponding topology routing table.

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICDBINCONSISTENCE

3-Error

Inconsistent static route database due to [chars] on [inet]%m on [chars] via [inet]

An error has occurred due to inconsistence on static route table.

-

LOG_STD_RECUR_ACTION

IPRT-3-STATIC_GWIF_INCONSISTENCE

3-Error

Inconsistence static route database [chars] [chars] [inet]

-

-

-

IPRT-3-STATIC_SR_POLICY_INCONSISTENCE

3-Error

Inconsistence static route database due to [chars] on [inet]%m via policy [chars] [dec]

-

-

-

IPRT-3-STATICROUTES_FAILED_RW_START

3-Error

Failed to start route watch for topology [chars] gateway [inet]%m flag 0x[hec] rc [dec]

An error has occurred failed to start route watch for this static route.

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICROUTES_FAILED_RW_STOP

3-Error

Failed to stop route watch for static route handle [hec] route watch handle [hec] gateway [inet] interface [chars] rc [dec]

An error has occurred due to failed to stop route watch for this static route.

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICROUTES_ADDFAILED

3-Error

Failed to add static route to database [chars] on [inet]%m on [chars] via [inet]

An error has occurred due to failed add on static route table.

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICROUTES_RWATCH_FAILED_SIG

3-Error

Failed to get the correct route watch signature [hec]

An internal error has occurred which could cause inconsistence routing table due to route watch

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICROUTES_RWATCH_FAILED_LOOP

3-Error

Route watch failed to determine to keep a loop or not

An internal error has occurred which could cause inconsistence routing table due to route watch

-

LOG_STD_RECUR_ACTION

IPRT-3-STATICROUTES_RWATCH_FAILED_GET_INFO

3-Error

Failed to get the route info through route watch

An internal error has occurred which could cause inconsistence routing table due to route watch

-

LOG_STD_RECUR_ACTION

IPRT-3-NO_MAJORNET_NDB

3-Error

No majornet found: [chars] [inet]%m

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_DEL_ERROR

3-Error

Error Removing an NDB [chars] [inet]%m tid 0x[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_CREATE_ERROR

3-Error

Error creating an NDB - [chars] [dec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-INVALID_NEXTHOP

3-Error

[chars] ID 0x[hec] [inet]%m from [chars] Gwy: [inet] [chars] Binding Label: [chars] Type:0x[hec] Attr 0x[hec] Has Repair Path: [dec] Repair Gwy: [inet] [chars]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-INVALID_RIBUPDATE_STATE

3-Error

Invalid RIB State for update 0x[hec] [inet]%m [chars]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-NDB_PDB_MATCH_INVALID

3-Error

Invalid ndb_pdb_match_type 0x[hec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-RIB_LOOP

3-Error

Resolution loop formed by routes in RIB

RIB route producers have installed routes in the RIB that form a loop during resolution.

-

"Resolve the RIB route resolution loop:\n" "1 Determine which routes are involved in the loop by issuing the "

IPRT-3-PROTOFLTR_ROUTE_MAP_CONFIG_ERROR

3-Error

Protocol filter routemap [chars] configuration failed

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-PROTOFLTR_SB_ADD_ERROR

3-Error

Topology 0x[hec] interface [chars] add sub-block failed for sb_type [dec]

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-PROTOFLTR_INVALID_ACL_TYPE

3-Error

Invalid ACL type [dec] is configured.

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-3-PARSER_REG_ERROR

3-Error

Unable to register [chars] submode translation callback mode = 0x%X

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-RESPAWN_COUNT_ERROR

3-Error

Unable to get process respawn count

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-HMI_INIT_ERROR

3-Error

Unable to init HMI database

RIB_INT_ERR_EXPLANATION

-

LOG_STD_RECUR_ACTION

IPRT-3-TOPO_HANDLE_ERROR

3-Error

Unable to get topology handler topoid = [dec] [chars]

RIB_INT_ERR_EXPLANATION

ip

LOG_STD_RECUR_ACTION

IPRT-3-INCONSISTENT_TOPOID_ERROR

3-Error

Inconsistent topology id topoid:0x[hec] and topoid:0x[hec] are found for the topology[chars]

-

-

-

IPRT-3-PDB_STATIC_ERROR

3-Error

Static pdb procinfo is NULL

RIB_INT_ERR_EXPLANATION

ip

LOG_STD_RECUR_ACTION

IPRT-3-CFORK

3-Error

Old-style routing processes no longer supported

RIB_INT_ERR_EXPLANATION

ip

LOG_STD_RECUR_ACTION

IPRT-3-RIB_INTERNAL_ERR

3-Error

[chars]

RIB_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

IPRT-5-STATICROUTES_BFD_EVENT

5-Notice

BFD session [chars][[chars]]

An ipv4 static route BFD session has either come up or gone down \n The message describes the change for it. This message appears only if the <Bold>log<nobold> command is configured for the ipv4 static route BFD process.

-

"This informational message normally appears as routers and \n\ ipv4 static route BFD sessions go up or down."

IPRT-3-MAXALLOWEDLIMITREACHED

3-Error

Maximum allowed static route count reached: [dec] \n ip_addstatic_route failed \n

The maximum number of static routes that can be configured is reached. No further routes will be added to the table

-

"Remove the unwanted static routes to add more routes"

IPRT-4-RWATCHUSAGEWARN

4-Warning

Route watch client-[chars] is calling the API from RIB context !!

Improper usage of the API spotted from the caller.\n Check if the api was called directly from a notification callback

-

"Ideal usage is to enqueue the RWATCH notifications to a client process and the api should be called from client context"

ROUTEMAP-4-BADTRACKOBJECTTYPE

4-Warning

can't track this type of object

Route maps only support STATE type track objects. This object is not a STATE object

routemap

"Reconfigure the track object to make it a STATE object."

MPLS_VPN_ISSU-3-ISSU_RC_ERR

3-Error

[chars] [chars]

MPLS VPN ISSU client ISSU infra related error.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_ISSU-3-GENERR

3-Error

[chars]

MPLS VPN ISSU client general error.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_ISSU-3-CF_ERR

3-Error

[chars] 0x[hec]

MPLS VPN ISSU client CF related error.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-3-SIZEMISMATCH

3-Error

Label table size [dec] mismatch get label tableid failed.

MPLS VPN HA Label Table size mismatch.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-7-LABELFREE

7-Debug

[chars] [dec]

MPLS VPN Label Manager failed to free label.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-3-CLIENTREG

3-Error

[chars]

MPLS VPN HA failed to register to CF.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-7-MALLOCFAIL

7-Debug

[chars]

MPLS VPN HA failed to allocate memory

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-7-XMITFAIL

7-Debug

[chars] message seq no [dec] current seq no [dec]

MPLS VPN Label Manager failed to deliver a message

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-3-CF_GEN_ERROR

3-Error

[chars]

MPLS VPN HA client CF related general error.

mpls-vpn

LOG_STD_ACTION

MPLS_VPN_HA-3-DBOPERATION

3-Error

[chars] RD [chars] [inet]/[dec] label [dec]

MPLS VPN HA Checkpoint database operation error.

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-MEM

3-Error

[chars]

Error in memory management

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-LSD1

3-Error

[chars] [chars]

Error in BGP LMM and LSD interaction

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-LSD2

3-Error

[chars] [chars] [chars]

Interaction error between BGP LMM and LSD

mpls-vpn

LOG_STD_ACTION

BGP_LMM-6-PERCE1

6-Information

Per CE label global keyid wrap trigger label reallocation

Per CE label global keyid wrap trigger label reallocation

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-CFC1

3-Error

[chars] [chars]

Error in BGP LMM and CFC interaction

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-CFC2

3-Error

[chars] [chars] [chars]

Interaction error between BGP LMM and CFC

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-IPRMCONNECT

3-Error

[chars] Address-family [chars]

BGP LMM AF registration/de-registration with IPRM failed

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-NBRROUTE

3-Error

[chars] Neighbor: [chars] Interface: [chars]

A host route to an MPLS enabled BGP neighbor was not present in the routing table the problem was corrected by installing the route

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-AUTOGEN

3-Error

[chars] Neighbor: [chars] Interface: [chars]

There was an error while auto-generating the mpls bgp forwarding command on an interface

mpls-vpn

"Manually configure the mpls bgp forwarding command" " on the interface referenced in the error message." "If the problem persists copy the message exactly as" "it appears and report it to your customer service" "representative"

BGP_LMM-6-AUTOGEN1

6-Information

[chars] interface: [chars]

The mpls bgp forwarding command has been automatically configured on an interface

-

"This is an informational message no action is " "required by the operator"

BGP_LMM-3-PATH

3-Error

[chars] label: [dec] next hop: [dec]

Invalid information in a BGP path

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-SIZEMISMATCH

3-Error

Label table size [dec] mismatch checkpoint key creation failed

MPLS Label Table ID size mismatch.

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-VRFAGGR

3-Error

[chars] [dec]

Error during per VRF aggregate label processing

mpls-vpn

LOG_STD_ACTION

BGP_LMM-4-LABEL

4-Warning

[chars] [chars]

Error during allocation/freeing of a label

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-REENTRY

3-Error

[chars]

A non re-entrant routine has been re-entered

mpls-vpn

LOG_STD_ACTION

BGP_LMM-3-ASSERT

3-Error

Assert failed at [chars]:[dec]

An internal software error has occurred

mpls-vpn

LOG_STD_ACTION

BGP_LMM-6-MPLS_INIT

6-Information

MPLS has been [chars] for the BGP address-family [chars]

MPLS has been enabled/disabled for a given BGP address-family

-

"This is an informational message no action is " "required by the operator"

FRRMGR-3-FRRMGR_INTERNAL_ERR

3-Error

[chars]

FRRMGR_INT_ERR_EXPLANATION

ribinfra

LOG_STD_RECUR_ACTION

APM-3-INIT

3-Error

[chars]

Easy Perf Mon Initialization failed

media-mon

LOG_STD_ACTION

APM-3-LIST

3-Error

[chars] [chars]

List operation error occurred.

media-mon

LOG_STD_ACTION

APM-3-MEM

3-Error

Memory [chars] failed - [chars]

Memory operation failed

media-mon

LOG_STD_ACTION

APM-3-CACHE_SIZE

3-Error

Configured cache size is too large. Value has been limited to [dec]100 x platform default.

configured cache size is too big

media-mon

LOG_STD_ACTION

MMA-3-MEM

3-Error

Memory [chars] failed - [chars]

Memory creation failed during the initialization

media-mon

LOG_STD_ACTION

MMA-3-LIST

3-Error

Failed to [chars] list [chars]

A list operation failed. This could be caused by memory corruption

media-mon

LOG_STD_ACTION

MMA-3-PROV

3-Error

[chars]

A fatal error happened during provision

media-mon

LOG_STD_ACTION

MMA-3-PARSER

3-Error

[chars]

Error during register parser or parsing CLI

media-mon

LOG_STD_ACTION

MMA-3-INV_MONITOR

3-Error

The flow monitor pointer is invalid

An internal error occurred. The performance-monitor monitor pointer saved in the common monitor is NULL

media-mon

LOG_STD_ACTION

MMA-3-INV_COMMON_MONITOR

3-Error

The common monitor pointer is invalid

An internal error occurred. The common monitor pointer saved in the performance-monitor monitor is NULL

media-mon

LOG_STD_ACTION

MMA-3-INV_MONITOR_TYPE

3-Error

The monitor type [dec] is invalid

An internal error occurred. The monitor type is out of the range

media-mon

LOG_STD_ACTION

MMA-3-INV_DB_OBJ

3-Error

Internal error mma db pointer invalid

No valid pointer to mma db

media-mon

LOG_STD_ACTION

MMA-3-DB

3-Error

[chars]

Error during managing MMA database

media-mon

LOG_STD_ACTION

MMA-3-MCOL

3-Error

[chars]

Error during collecting metrics in MMA PI

media-mon

LOG_STD_ACTION

MMA-3-FIELD

3-Error

[chars]

Error during initializing a field

media-mon

LOG_STD_ACTION

MMA-3-CHUNKCREATE

3-Error

Failed to chunk create memory for [chars]

Unable to chunk create memory chunk

media-mon

LOG_STD_ACTION

MMA-3-CHUNKDESTROY

3-Error

Failed to chunk destroy memory for [chars]

Unable to chunk destroy memory chunk

media-mon

LOG_STD_ACTION

MMA-3-CHUNKMALLOC

3-Error

Failed to malloc chunk memory for [chars]

Unable to malloc memory chunk malloc failed

media-mon

LOG_STD_ACTION

MMA-3-FLOW_EXCEED

3-Error

The number of flows has exceeded 95%% of the configured maximum flow. [chars]\n

This is warning message if the flow size exceeds the maximum value

media-mon

LOG_STD_ACTION

MMA-3-FLOW_NONEXCEED

3-Error

The number of flows is below 85%% of the configured maximum flow. [chars]\n

This is info message if the flow size falls below the maximum value

media-mon

LOG_STD_ACTION

MMA-3-CACHE_OVERFLOW

3-Error

The number of flows has exceeded 95%% of the configured size monitor [chars] please increase cache size\n

This is warning message if the flow size exceeds the maximum value

media-mon

LOG_STD_ACTION

MMA-3-INV_REACT

3-Error

react is not valid - [chars]

This is an internal error the saved react info is corrupted

media-mon

LOG_STD_ACTION

MMA-3-INV_ACTION_OBJ

3-Error

action object is not valid - [chars]

This is an internal error the saved action object info is corrupted

media-mon

LOG_STD_ACTION

MMA-3-NULLHIST

3-Error

A history bucket does not exist

An internal error occurred. Try to access a null history

media-mon

LOG_STD_ACTION

MMA-3-NULLFLOW

3-Error

A flow does not exist

An internal error occurred. Try to access a null flow

media-mon

LOG_STD_ACTION

MMA-3-INV_ARG

3-Error

The argument is not valid - [chars]

An internal error occurred. The argument for an internal API is not valid

media-mon

LOG_STD_ACTION

MMA-3-RM_SET

3-Error

[chars]

An error happened during setting of Resource Manager event

media-mon

LOG_STD_ACTION

PERF_MON_REACT-0-EMERGSET

0-Emergency

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is EMERGENT. system is unusable.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-0-EMERGCLEAR

0-Emergency

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is EMERGENT.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-1-ALERTSET

1-Alert

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is ALERT.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-1-ALERTCLEAR

1-Alert

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is ALERT.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-2-CRITSET

2-Critical

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is CRITICAL.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-2-CRITCLEAR

2-Critical

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is CRITICAL.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-3-ERRSET

3-Error

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is ERROR

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-3-ERRCLEAR

3-Error

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is ERROR

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-2-INFOSET

2-Critical

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is INFO.

media-mon

LOG_STD_NO_ACTION

PERF_MON_REACT-2-INFOCLEAR

2-Critical

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is INFO.

media-mon

LOG_STD_NO_ACTION

MMA_DP-3-MEM

3-Error

Memory [chars] failed - [chars]

Memory creation failed during the initialization

media-mon

LOG_STD_ACTION

MMA_DP-3-LIST

3-Error

Failed to [chars] list [chars]

A list operation failed. This could be caused by memory corruption

media-mon

LOG_STD_ACTION

MMA_DP-3-TEMPLATE

3-Error

Create flow template error [chars]

Error happened during creating MMA PD flow def template

media-mon

LOG_STD_ACTION

MMA_DP-3-INIT

3-Error

Error during initialization error [chars]

Error happened during initialization of MMA Data plane

media-mon

LOG_STD_ACTION

PERF_MON-3-LIST

3-Error

Failed to [chars] list [chars]

A list operation failed. This could be caused by memory corruption

media-mon

LOG_STD_ACTION

PERF_MON-3-MEM

3-Error

Memory [chars] failed - [chars]

Memory creation failed during the initialization

media-mon

LOG_STD_ACTION

PERF_MON-3-PARSER

3-Error

[chars]

Parser failure. This could due to invalid command or corrupted csb

media-mon

LOG_STD_ACTION

PERF_MON-3-CHUNKCREATE

3-Error

Failed to chunk create memory for [chars]

Unable to chunk create memory chunk

media-mon

LOG_STD_ACTION

PERF_MON-3-CHUNKDESTROY

3-Error

Failed to chunk destroy memory for [chars]

Unable to chunk destroy memory chunk

media-mon

LOG_STD_ACTION

PERF_MON-3-CHUNKMALLOC

3-Error

Failed to malloc chunk memory for [chars]

Unable to malloc memory chunk malloc failed

media-mon

LOG_STD_ACTION

PERF_MON-3-DEFRECCREATE

3-Error

Creation of default-record [chars] failed - reason [chars]

Failed to create system defined default flow-records

media-mon

LOG_STD_ACTION

PERF_MON-3-RECSETPROP

3-Error

Setting property for [chars] default-record failed - reason [chars]

Failed to set properties for system defined default flow-records

media-mon

LOG_STD_ACTION

PERF_MON-3-RECSETKEY

3-Error

Adding key fields for default-record [chars] failed - reason [chars]

Failed to add key fields for defined default flow-records

media-mon

LOG_STD_ACTION

PERF_MON-3-RECSETNONKEY

3-Error

Adding non-key fieds for [chars] default-record failed - reason [chars]

Failed to add non-key fields for defined default flow-records

media-mon

LOG_STD_ACTION

PERF_MON_ASYNC-3-LIST

3-Error

Failed to [chars] list [chars]

A list operation failed. This could be caused by memory corruption

media-mon

LOG_STD_ACTION

PERF_MON_ASYNC-3-MEM

3-Error

Memory [chars] failed - [chars]

Memory creation failed during the initialization

media-mon

LOG_STD_ACTION

PERF_MON_ASYNC-3-INIT

3-Error

[chars]

Failure during perf-mon async initialization

media-mon

LOG_STD_ACTION

PERF_MON_MENG-3-INIT

3-Error

[chars]

Failure during perf-mon data plane initialization

media-mon

LOG_STD_ACTION

PERF_MON_MENG-3-LIST

3-Error

Failed to [chars] list [chars]

A list operation failed. This could be caused by memory corruption

media-mon

LOG_STD_ACTION

PERF_MON_MENG-3-MEM

3-Error

Memory [chars] failed - [chars]

Memory operation failure

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_REACT-0-EMERGSET

0-Emergency

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is EMERGENT. system is unusable.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-0-EMERGCLEAR

0-Emergency

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is EMERGENT.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-1-ALERTSET

1-Alert

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is ALERT.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-1-ALERTCLEAR

1-Alert

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is ALERT.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-2-CRITSET

2-Critical

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is CRITICAL.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-2-CRITCLEAR

2-Critical

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is CRITICAL.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-3-ERRSET

3-Error

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is ERROR

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-3-ERRCLEAR

3-Error

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is ERROR

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-2-INFOSET

2-Critical

TCA RAISE. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is raised. The alarm severity is INFO.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_REACT-2-INFOCLEAR

2-Critical

TCA CLEAR. \nDetailed info: [chars][chars][chars][chars][chars]\n

A threshold crossing alarm is cleared. The alarm severity is INFO.

media-mon

LOG_STD_NO_ACTION

PERF_TRAFFIC_METER-3-INITFAIL

3-Error

Metering engine initialization fail - [chars]\n

An internal error occurred. Unable to initialize the performance monitor metering engine

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_METER-3-MONITOR_UNBIND

3-Error

Failed to unbind monitor from target. Error - [chars]

Failed to unbind monitor at Metering layer for this target. The error code provides the reason for failure.

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-MMONOBJINV

3-Error

A mmon_obj does not exist for policy [chars] class [chars]\n

Unable to find an existing mmon obj for event CLASS_REMOVE and CLASS_MODIFY

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-MMONOBJDUP

3-Error

A mmon_obj already exists for policy [chars] class [chars]\n

A mmon obj already exists in the MMON DB under the same policy and class for CLASS_ADD

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-NOPARENTMMONOBJ

3-Error

Internal error target has no parent mmon object

None valid pointer to mmon obj found in tgt obj for CLASS_REMOVE

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INV_REACT

3-Error

react is not valid - [chars]

This is an internal error the saved react info is corrupted

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-FIELDENA

3-Error

Enable fnf field [chars] failed - [chars]

Failed to enable a field for use with a config

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-FNFPARSERENA

3-Error

Enable flow monitor parser failed - [chars]

Failed to enable performance monitor typed monitor

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-CHUNKCREATE

3-Error

Failed to chunk create memory for [chars]

Unable to chunk create memory chunk

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-CHUNKDESTROY

3-Error

Failed to chunk destroy memory for [chars]

Unable to chunk destroy memory chunk

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-CHUNKMALLOC

3-Error

Failed to malloc chunk memory for [chars]

Unable to malloc memory chunk malloc failed

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INV_TARGET

3-Error

A target object does not exist - [chars]

An internal error occurred. Try to access a null target obj

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-NULLHIST

3-Error

A history bucket does not exist

An internal error occurred. Try to access a null history

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-NULLFLOW

3-Error

A flow does not exist

An internal error occurred. Try to access a null flow

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INVCMD

3-Error

Invalid cmd type [dec] to [chars]

This is an internal error the command type is invalid

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INVMODE

3-Error

Invalid performance-monitor configuration mode

This is an internal error the configuration sub mode is invalid

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INVCRIT

3-Error

Invalid react criteria [dec] to [chars]

This is an internal error the saved react criteria is corrupted

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-RESETMODE

3-Error

Failed to reset csb vars

Reset of the csb vars failed due to lack of memory

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-DEFRECCREATE

3-Error

Creation of default-record [chars] failed - reason [chars]

Failed to create system defined default flow-records

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-RECSETPROP

3-Error

Setting property for [chars] default-record failed - reason [chars]

Failed to set properties for system defined default flow-records

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-RECSETKEY

3-Error

Adding key fields for default-record [chars] failed - reason [chars]

Failed to add key fields for defined default flow-records

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-RECSETNONKEY

3-Error

Adding non-key fieds for [chars] default-record failed - reason [chars]

Failed to add non-key fields for defined default flow-records

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-MONITOR_CREATE

3-Error

Failed to create Monitor at Metering layer. Error - [chars]

Failed to create monitor at Metering layer for this policy. The error code provides the reason for failure. No statistics will be collected.

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-MONITOR_DELETE

3-Error

Failed to delete Monitor at Metering layer. Error - [chars]

Failed to delete monitor at Metering layer for this policy. The error code provides the reason for failure.

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-MONITOR_SYNC

3-Error

Out of sync - [chars]

This is an internal error the reference count in flow monitor reached negative

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INVFIELDTYPE

3-Error

Enable fnf field [dec] failed - invalid field type

Failed to enable a field for use with a config

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INVMONITOR

3-Error

The flow monitor pointer is invalid

An internal error occurred. The performance-monitor monitor pointer saved in the common monitor is NULL

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INV_COMMON_MONITOR

3-Error

The common monitor ptr is invalid

An internal error occurred. The common monitor ptr saved in the performance-monitor monitor is NULL

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INV_MONITOR_TYPE

3-Error

The monitor type [dec] is invalid

An internal error occurred. The monitor type is out of the range

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INV_POLICY_MAP

3-Error

The retrieved policy map is invalide - [chars]

An internal error occurred. The policy map saved in csb is invalid

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-INV_ARG

3-Error

The argument is not valid - [chars]

An internal error occurred. The argument for an internal API is not valid

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-CONV_FAILURE

3-Error

Conversion failed - [chars]

Conversion from one format to another has failed

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-CHUNK_INIT

3-Error

Chunk is not initialized - [chars]

Chunk memory is not created or failed to be created

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-PROC_MSG

3-Error

Failed to process received record - [chars]

Failure during the process of handling the received fnf record

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-MEMLEAK

3-Error

Memory leak detected - [chars]

A memory leak is detected during media-mon memory handling

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-FDEF_NOTIFY

3-Error

Failed to register PD flow definition [chars]

The flow def received from ME or PD is NULL

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-EXP_ATTR

3-Error

Failed to set flow attribute for exporter - [chars]

An error occured when setting flow attribute use to transform match and collect metrics to export message

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-FDEF_TEMP

3-Error

Invalid flow definition template - [chars]

The template was not initialized during system initialization

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-FLOW_EXCEED

3-Error

The number of flows has exceeded 95%% of the configured maximum flow. [chars]\n

This is warning message if the flow size exceeds the maximum value

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-FLOW_NONEXCEED

3-Error

The number of flows is below 85%% of the configured maximum flow. [chars]\n

This is info message if the flow size falls below the maximum value

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-SIB_LINK

3-Error

sib member [dec] with [dec] error [chars]

Failed to link two sibling members in the MMON PD

media-mon

LOG_STD_ACTION

PERF_TRAFFIC_INFRA-3-SIB_UNLINK

3-Error

sib member [dec] from [dec] error [chars]

Failed to unlink two sibling members in the MMON PD

media-mon

LOG_STD_ACTION

COLLECTOR-3-EXISTING_COLLECTOR

3-Error

Collector [chars] already exists\n

A collector already exists. Only one collector may be configured at a time.

media-mon - collector

"Modify the existing collector or remove it " "and create a new one with the desired name"

COLLECTOR-3-RESETMODE

3-Error

Failed to reset csb vars

Reset of the csb vars failed due to lack of memory

media-mon - collector

LOG_STD_ACTION

COLLECTOR-3-PROCESS_FAIL

3-Error

Failed to start collector process

An error occurred when attempting to start the collector

media-mon - collector

LOG_STD_ACTION

COLLECTOR-3-PORT_CHANGE_FAIL

3-Error

Failed to set the collector port to [dec]

An error occurred when attempting change the collector port. The port has reverted to the previous value

media-mon - collector

LOG_STD_ACTION

COLLECTOR-3-MODE_CHANGE_FAIL

3-Error

The collector mode is invalid

An error occurred when attempting change the collector mode. The mode has reverted to the previous value

media-mon - collector

LOG_STD_ACTION

COLLECTOR-3-REMOVE_FAIL

3-Error

The collector name is unrecognized

The Collector name give does not match the collector configured

media-mon - collector

LOG_STD_ACTION

DOMAIN-5-TC_PATH_CHG

5-Notice

Traffic class Path Changed. Details: [chars]\n

A Path chage is made.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-6-TC_CTRL

6-Information

Traffic Class Controlled. Details: [chars]\n

A Traffic Class is Controlled.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-6-TC_NEW

6-Information

Traffic Class Learned. Details: [chars]\n

A Traffic Class is Learned.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-5-TCA

5-Notice

[chars] Received. Details: [chars]\n

A threshold crossing alarm is raised.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-2-IME

2-Critical

Immitigable event occured. IME-ID=[dec]: Details: [chars]\n

Error encounterd during TCA processing. The flow could not be placed on alternate path.

ng-pfr

"Troubleshoot the network for performance/bandwidth issues."

DOMAIN-2-IME_DETAILS

2-Critical

IME-ID=[dec]: [chars]\n

Error encounterd during TCA processing. The flow could not be placed on alternate path.

ng-pfr

"Troubleshoot the network for performance/bandwidth issues."

DOMAIN-3-PLR_INT_CFG

3-Error

[chars]

Conflicting Domain configuration exists on the selected WAN interface on border.

ng-pfr

"Correct the domain path configuration on selected WAN interface on border and retry."

DOMAIN-6-INIT

6-Information

[chars]

Informational Message. Domain master controller initialization completed

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-5-MC_STATUS

5-Notice

[chars]

Master Controller Status Notification.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-4-MC_SHUTDOWN

4-Warning

Reason=[chars]

Master Controller Shutdown Warning Message.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-6-MC_TC_ID_RESET

6-Information

Master Controller traffic class id counter got reset: site_id=[inet] domain=[chars] vrf=[chars]

Master Controller traffic class id counter got reset.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-6-MC_POLICY_DOWNLOAD

6-Information

Master Controller policy downloaded: site_id=[inet] domain=[chars] vrf=[chars]

Master Controller policy downloaded.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-5-BR_STATUS

5-Notice

[chars]

Border Status Notification.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-4-BR_SHUTDOWN

4-Warning

Reason=[chars]

Border Shutdown Warning Message.

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-3-INVALID_EXIT

3-Error

[chars]

Inavlid Exit notification.

ng-pfr

"Correct the PLR interface configuration"

DOMAIN-4-PDP_PREFIX_REACH

4-Warning

[chars]

Prefix not reachable on the channel

ng-pfr

"Verify the reachability of the prefix"

DOMAIN-2-GLOBALS_XML_FAILURE

2-Critical

[chars]

Failed to decode xml message containing global parameters

ng-pfr

"Check if software versions are compatible"

DOMAIN-2-POLICY_XML_FAILURE

2-Critical

[chars]

Failed to decode xml message containing policy definition

ng-pfr

"On Hub MC check if invalid characters are used in policy name"

DOMAIN-2-PMI_XML_FAILURE

2-Critical

[chars]

Failed to decode xml message containing pmi parameters

ng-pfr

"Check if software versions are compatible"

DOMAIN-3-HUB_SITE_ID_ERR

3-Error

[chars]

Hub site-id error notification.

ng-pfr

"Correct the Hub MC ip-address configuration"

DOMAIN-4-SITE_PREFIX

4-Warning

[chars]

Improper site prefix configuration detected.

ng-pfr

"Correct your site prefix configuration"

DOMAIN-4-SMP

4-Warning

[chars]

Smart-Probe config is being changed

ng-pfr

LOG_STD_NO_ACTION

DOMAIN-4-WAN_INTERFACE

4-Warning

Interface \[chars]\ received probes but no \dynamic-path\ configured

-

-

-

DOMAIN-4-WAN_INTERFACE_TYPE_CONFLICT

4-Warning

Interface \[chars]\ discoveried as WAN interface. But DCA already configured.

Branch site border router WAN interface must have dynamic-path configured

ng-pfr

"configure domain <domain name> dynamic-path on WAN interface"

DOMAIN-4-DCA_DOMAIN_MAP

4-Warning

[chars]

DCA domain map error notification.

ng-pfr

"Correct the branch MC domain-map configuration."

DOMAIN-4-TUN_SRC_OVERLAPPED

4-Warning

[chars]

Tunnel source overlapped notification.

ng-pfr

"Correct the source configuration."

PKI-3-KEY_CMP_MISMATCH

3-Error

Key in the certificate and stored key does not match for Trustpoint-[chars].

Public key in the certificate is not the same as the stored key.

-

"Make sure that the certificate public key and stored public key are the same."

PKI-3-QUERY_KEY

3-Error

Querying key pair failed.

Querying public key/private key using subject name failed

-

"Resubmit enrollment request. Check the subject name."

PKI-3-CERTRETFAIL

3-Error

Certificate enrollment failed.

Certificate enrollment transaction failed due to internal error.

-

"Contact CE."

PKI-6-CERT_INSTALL

6-Information

[chars] \n Trustpoint : [chars] \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n End-date : [chars]

A previous certificate enrollment request was received by the Certificate Authority. It has issued the certificate and sent back a copy

pki

"Informational message only. No action required."

PKI-6-CERTPENDING

6-Information

Enter manual authentication ...

CA server want to manually authenticate the router.

-

"Follow a manual authentication procedure."

PKI-6-CERTREJECT

6-Information

[chars]

A previous certificate enrollment request was received by the Certificate Authority. It has rejected the enrollment request.

pki

"Contact the Certificate Authority administrator."

PKI-6-PKCS12_EXPORT_SUCCESS

6-Information

PKCS #12 Export from trustpoint [chars] was successfully Exported.

A PKCS #12 has been generated and successfully exported.

-

"No action required. Informational message"

PKI-6-PKCS12_IMPORT_SUCCESS

6-Information

PKCS #12 import in to trustpoint [chars] successfully imported.

A PKCS #12 has been successfully imported.

-

"No action required. Informational message"

PKI-3-POLLCACERT

3-Error

Polling CA certificate .....

Polling ca certificate.

-

"Check if CA or ldap server is online."

PKI-3-QUERYCACERT

3-Error

Failed to query CA certificate.

Failed to query ca certificate from ca server.

-

"Use parser command "cr ca auth" and try again."

PKI-3-INVALIDCACERT

3-Error

Failed to process CA certificate.

Failed to process the ca certificate received from ca server.

pki

"Use parser command "cr ca auth" and try again."

PKI-3-POLLRACERT

3-Error

Polling RA certificate .....

Polling ra certificate.

-

"Check if CA or ldap server is online."

PKI-3-POLLROUTERCERT

3-Error

Polling Router certificate for [chars] .....

Polling router certificate.

-

"Check if CA or ldap server is online."

PKI-4-NOAUTOSAVE

4-Warning

Configuration was modified. Issue \write memory\ to save new certificate

Auto-Enroll has obtained a new router key pair and certificate. However the running configuration was previously modified.

-

"Issue the \"write memory\" command to save the new certificates and keys."

PKI-6-AUTOSAVE

6-Information

Running configuration saved to NVRAM

Auto-Enroll has obtained a new router key pair and certificate and has done an automatic \write memory\ to save them.

-

"No action required. Informational message"

PKI-4-NOSHADOWAUTOSAVE

4-Warning

Configuration was modified. Issue \write memory\ to save new IOS CA certificate

IOS CA Rollover has generated a shadow CA key pair and certificate. However the running configuration was previously modified.

-

"Issue the \"write memory\" command to save the new certificates and keys."

PKI-6-CERTRENEWMANUAL

6-Information

Please renew the router certificate for trustpoint [chars]

Trustpoint certificate will expire soon and should be renewed

-

"Obtain a new certificate from the Certificate Authority"

PKI-6-CERT_RENEW_AUTO

6-Information

Auto renewing router certificate of trustpoint [chars]

Trustpoint certificate will expire soon and is being automatically renewed

-

"No action required. Informational message"

PKI-6-SHADOWAUTOSAVE

6-Information

Running configuration saved to NVRAM

IOS CA Rollover has generated a shadow CA key pair and certificate and has done an automatic \write memory\ to save them.

-

"No action required. Informational message"

PKI-4-NOCONFIGAUTOSAVE

4-Warning

Configuration was modified. Issue \write memory\ to save new IOS PKI configuration

IOS PKI APIs have generated new PKI configuration. However the running configuration was previously modified.

-

"Issue the \"write memory\" command to save the new PKI configuration."

PKI-6-CONFIGAUTOSAVE

6-Information

Running configuration saved to NVRAM

IOS PKI APIs have generated new PKI configuration and has done an automatic \write memory\ to save them.

-

"No action required. Informational message"

PKI-6-CERTIFSSEND

6-Information

Could not send Certificate enrollment request to file system.

The certificate enrollment request could not be sent to file system.

pki

"Verify the enrollment URL and that the router is able to" "write to the file system."

PKI-6-CERTIFSRECV

6-Information

Could not receive router's Certificate from file system.

The router's certificate could not be received from file system.

pki

"Verify the enrollment URL and that the router is able to" "read from the file system."

PKI-2-CERT_ENROLL_FAIL

2-Critical

Certificate enrollment failed for trustpoint [chars]. \n Reason : [chars]

Certificate enroll encounter fatal error

pki

"Contact the CA administrator."

PKI-2-CERT_RENEW_FAIL

2-Critical

Certificate renewal failed for trustpoint [chars] \n Reason : [chars]

Certificate enroll encounter fatal error

pki

"Contact the CA administrator."

PKI-4-CERT_ENROLL_CANCEL

4-Warning

Enrollment cancelled for trustpoint : [chars]

Certificate enroll cancelled by user

pki

"Contact the CA administrator."

PKI-3-SOCKETSEND

3-Error

Failed to send out message to CA server.

The failure is caused by http transaction.

-

"Check http connection to the CA server"

PKI-3-INVALID_INPUT

3-Error

The input to the parser command is not correct

The input to the parser command is not correct

-

"Repeat the command."

PKI-3-GETCARACERT

3-Error

Failed to receive RA/CA certificates.

Encountered failure when parsing and processing CA/RA certificates

-

"Check the status contact the CA administrator"

PKI-6-CS_DELETE_TP_KEY

6-Information

Trustpoint and key deleted.

Trustpoint and key used by the Certificate Server are deleted.

-

"No action required. Informational message."

PKI-6-CS_DELETE

6-Information

Certificate Server is deleted.

Certificate Server is deleted.

-

"No action required. Informational message."

PKI-6-CS_GRANT_AUTO_RA

6-Information

Enrollment requests coming from known RAs will be automatically granted.

Enrollment requests coming from known RAs will be automatically granted.

-

"No action required. Informational message."

PKI-6-CS_GRANT_AUTO

6-Information

All enrollment requests will be automatically granted.

All enrollment requests will be automatically granted.

-

"No action required. Informational message."

PKI-6-CS_GRANT_AUTO_CACERT

6-Information

All rollover subordinate CA cert requests will be automatically granted.

All rollover subordinate CA cert requests will be automatically granted.

-

"No action required. Informational message."

PKI-4-CS_GRANT_AUTO_CACERT_FAILURE

4-Warning

A rollover request for a subordinate CA certificate cannot be auto granted.

A rollover request for a subordinate CA certificate cannot be authorized and the configured auto grant policy will be ignored. This request will be added to the CS server request queue but will need to be manually granted

pki

"Insure that the peer's current sub CA cert is valid."

PKI-6-CS_GRANT_AUTO_RACERT

6-Information

All rollover RA cert requests will be automatically granted.

All rollover RA cert requests will be automatically granted.

-

"No action required. Informational message."

PKI-6-CS_REJECT_AUTO

6-Information

All enrollment requests will be automatically rejected.

All enrollment requests will be automatically rejected.

-

"No action required. Informational message."

PKI-3-CS_CRIT_STORAGE

3-Error

Critical certificate server storage [chars] is inaccessible server disabled.

Critical certificate server storage is inaccessible server disabled.

-

"Make storage accessible or re-configure the storage location"

PKI-4-CS_PUBLISH_STORAGE

4-Warning

Publish certificate server storage [chars] is inaccessible.

Publish certificate server storage is inaccessible.

-

"Make storage accessible or re-configure the storage location"

PKI-6-AUTOENROLL_KEY_LOCKED

6-Information

Auto-enroll failed - RSA keypair is locked

Auto-enroll attempted to generate a new RSA keypair. However the existing RSA keypair is locked so auto-enroll cannot proceed

-

"Auto-enroll will retry the enrollment request" "Make sure the existing RSA keypair is unlocked before the next retry"

PKI-6-CS_ENABLED

6-Information

Certificate server now enabled.

Certificate server now enabled.

-

"No action required. Informational message."

PKI-6-CS_DISABLED

6-Information

Certificate server now disabled. \n Reason : [chars]

Certificate server now disabled.

-

"No action required. Informational message."

PKI-3-UNUSABLE_KEY_USAGE

3-Error

Key-usage type '[chars]' for cert with serial number [chars] is not usable.

The given key-usage type is not usable by IOS. If seen during an import operation this will likely cause the import to fail. Acceptable key-usage types should include Key-encipherment and/or digital-signature. Other key-usage types may be present but will be ignored.

-

"Recreate the certificate with Key-encipherment " "digital-signature or both."

PKI-6-AUTOCERTFAIL

6-Information

Certificate reenrollment failed. Delaying before retry

Automatic certificate enrollment or re-enrollment failed The router will retry in 6 hours or less depending on the expiration time of the router's certificate.

pki

"Contact the CA administrator."

PKI-4-AUTOCERTFAILWARN

4-Warning

Certificate reenrollment failed. Delaying before retry

Automatic certificate re-enrollment failed. The router will retry in 6 hours or less depending on the expiration time of the router's certificate. Caution - Router's Certificate may expire soon.

pki

"Contact the CA administrator. The router will retry."

PKI-3-AUTOCERTERR

3-Error

Auto Certificate reenrollment failed. Cannot retry

Automatic certificate re-enrollment failed. The router clock my not be set correctly. If the router has a certificate it may be expired.

pki

"Check router clock is set correctly" "Make sure the router's cert has not expired"

PKI-3-CERTPENDERR

3-Error

Failed to receive pending certificate during enrollment

The router's cert remains in a pending state after the maximum number of retries to enroll.

pki

"Contact the CA administrator. Then retry the enrollment."

PKI-4-CERTIFICATE_INVALID_SUBJECT

4-Warning

Certificate has a missing or invalid subject name.

The certificate subject name attribute must be present and not empty OR The certificate subject alt name extension must be present and include at least one entry.

pki

"Examine the offending certificate and re-issue it with a proper subject name."

PKI-3-CERTIFICATE_INVALID_EXPIRED

3-Error

Certificate chain validation has failed. The certificate SN: [chars] has expired.

The certificate validity period indicates that this certificate has expired

pki

"Check the system clock to see if its set correctly"

PKI-3-CERTIFICATE_INVALID_NOT_YET_VALID

3-Error

Certificate chain validation has failed. The certificate SN: [chars] is not yet valid

The certificate validity period indicates that this certificate is not yet valid

pki

"Check the system clock to see if its set correctly"

PKI-3-CERTIFICATE_INVALID

3-Error

Certificate chain validation has failed.

The certificate is not valid

pki

"Check the system clock to see if its set correctly"

PKI-3-CERTIFICATE_REVOKED

3-Error

Certificate chain validation has failed. The certificate SN: [chars] is revoked

The certificate has been revoked by the CA administrator.

pki

"Check the status contact the CA administrator"

PKI-3-CERTIFICATE_INVALID_UNAUTHORIZED

3-Error

Certificate chain validation has failed. Unauthorized

The certificate is valid but not authorized

pki

"Check the system clock to see if its set correctly"

PKI-4-CRLHTTPFETCHFAIL

4-Warning

CRL Request for trustpoint \[chars]\ returned [dec] [chars]

The CRL fetch returned something other than success. If the trustpoint revocation-check includes the keyword 'none' the transaction will succeed. If revocation- checking is not optional the transaction will fail.

pki

"Verify that the CRL is at the location specified " "in the Certificate and that the server is " "operational. To see interaction between IOS and " "the CRL-server please turn on <CmdBold>debug " "crypto pki transactions<NoCmdBold>"

PKI-6-CRLHTTPFETCHREDIR

6-Information

CRL Request for trustpoint \[chars]\ returned [dec] [chars] -> [chars]

The CRL fetch returned a redirect directive. This need not be an error if the file exists at the redirected location.

pki

"If no other errors are seen then the CRL was " "fetched from the new location and no action is " "necessary. To see interaction between IOS and " "the CRL-server please turn on <CmdBold>debug " "crypto pki transactions<NoCmdBold>"

PKI-3-CRL_FETCH_FAIL

3-Error

CRL fetch for trustpoint [chars] failed \n Reason : [chars]

The CRL fetch returned something other than success.

pki

"Check the CRL manually to see it is correct. " "To see interaction between IOS and the CRL-server " "please turn on <CmdBold>debug crypto pki " "transactions<NoCmdBold>"

PKI-3-CRL_INSERT_FAIL

3-Error

CRL download for trustpoint \[chars]\ has been discarded. \n Reason : [chars] \n Status : [dec] \n Status String : [chars]

Inserting and/or verifying the CRL failed. If the trustpoint revocation-check includes the keyword 'none' the transaction will succeed. If revocation- checking is not optional the transaction will fail.

pki

"Check the CRL manually to see it is correct. " "To see interaction between IOS and the CRL-server " "please turn on <CmdBold>debug crypto pki " "transactions<NoCmdBold>"

PKI-4-HTTPREDIRECT

4-Warning

Maximum Redirection limit of [dec] exceeded trying to retrieve URL [chars]

While fetching a document via http there were too many redirections and the operation has aborted. If the trustpoint revocation-check includes the keyword 'none' the transaction will succeed. If revocation- checking is not optional the transaction will fail.

pki

"Verify that the CRL is at the location specified " "in the Certificate and that the server is " "operational. To see interaction between IOS and " "the CRL-server please turn on <CmdBold>debug " "crypto pki transactions<NoCmdBold>"

PKI-4-CRL_LDAP_QUERY

4-Warning

An attempt to retrieve the CRL from [chars] using LDAP has failed

An LDAP query was made to acquire the certificate revocation list but the LDAP server did not respond with the requested information. This is a warning that only applies to the Distribution Point listed. It does not necessarily reflect the overall success or failure of CRL aquistion since a prior or subsequent retrival of the CRL may have succedeed.

pki

"Check that the LDAP server is reachable and online." "Verify that the CRL is at the requested location"

PKI-6-TRUSTPOOL_AUTO_UPDATE

6-Information

Auto-trustpool update in progress from [chars].

One of the certificates in the trustpool will expire soon. An attmpt to download a new trustpool bundle is in progress

pki

"Since an url has been configured that identifies the location to aquire the trustpool bundle " "then no action is required."

PKI-4-TRUSTPOOL_AUTO_UPDATE_DISABLED

4-Warning

Auto-trustpool update is disabled.

One of the certificates in the trustpool will expire soon. An attmpt to download a new trustpool bundle cannot be attempted since a bundle location is not configured

pki

"Either configure the bundle location in the trustpool policy or manually update the " "trustpool bundle."

PKI-4-TRUSTPOOL_EXPIRATION_WARNING

4-Warning

The Trustpool will expire in [chars].

One of the certificates in the trustpool will expire soon. If a bundle location is configured an auto aupdate will be attempted at predetermined intervals.

pki

"If a bundle location is configured in the trustpool policy no further action is required. Otherwise" "manual update of trustpool bundle may be needed."

PKI-6-ECDSA_CERT_WITH_SHA1

6-Information

User has accepted the security implication of using lesser hash strengthSHA1 for the Elliptic Curve Key present in the certificate

The SHA1 hash algorithm is not recommended for use with the elliptic curve key in this certificate. It is recommended that SHA2 or stronger hash algorithm be used.

pki

"Informational message only. No action required."

PKI-6-PKI_CRL_DOWNLOADED

6-Information

CRL download successful. \n Trustpoint : [chars] \n CDP-URL : [chars] \n Issuer : [chars]

CRL is downloaded and successfully inserted in the database. Notification for the same is sent to applications registered.

pki

"Informational message only. No action required."

PKI-4-CERT_EXPIRY_WARNING

4-Warning

[chars] Certificate belonging to trustpoint [chars] will expire in [dec] Days [dec] hours [dec] mins [dec] secs at [chars]. \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n Auto-Renewal : [chars]

Warning to indicate that certificate is expiring soon.

pki

"If auto-enrol feature is not configured re-enrol the certificate " "manually. Else check if any issues with auto-enrol."

PKI-1-CERT_EXPIRY_ALERT

1-Alert

[chars] Certificate belonging to trustpoint [chars] will expire in [dec] Days [dec] hours [dec] mins [dec] secs at [chars]. \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n Auto-Renewal : [chars]

Alert to indicate that certificate will expire in less than one week.

pki

"If auto-enrol feature is not configured re-enrol the certificate " "manually. Else check if any issues with auto-enrol."

PKI-4-OCSP_SERVER_NO_RESP

4-Warning

The OCSP Server URL [chars] is not reachable or not responding

The OCSP server is not reachable or is not responding to the OCSP request

pki

"Check if the OCSP server is reachable and is receiving the OCSP request"

PKI-4-OCSP_SERVER_RESP_COMP

4-Warning

The OCSP Server [chars]: error:responder certificate is peer certificate

The OCSP responder certificate is peer certificate

pki

"Check if the configured OCSP server and responder OCSP server is same or not"

PKI-3-OCSP_RESPONSE_STATUS

3-Error

OCSP response status failed \n Reason : [chars]

OCSP response status failed

pki

" Check the ocsp request or ocsp server configurations "

PKI-4-OCSP_SERVER_RESP_SIGN

4-Warning

The OCSP Server [chars]: error:responder invalid signature algorithm

The OCSP responder has differnt signature algorithm

pki

"Check if the configured and responder OCSP server ""same signature algorithm or not"

PKI-4-OCSP_SERVER_RESP_DECODE_FAIL

4-Warning

The OCSP Server [chars]: failed to decode OCSP response basic data

The OCSP response data decoding is failing

pki

"Check if the configured OCSP server response data"

PKI-4-OCSP_SERVER_CERT_VALIDATE

4-Warning

The OCSP Server [chars]: responder certificate validation failed

The OCSP server responder certificate validation failed

pki

"Check if the configured OCSP server responder certificate"

PKI-4-OCSP_SERVER_RESP_VARIFY

4-Warning

The OCSP Server [chars]: failed to verify OCSP response

The OCSP response verification failed

pki

"Check if the configured OCSP server response"

PKI-4-OCSP_SERVER_RESP_DECODE

4-Warning

The OCSP Server [chars]: failed to decode OCSP response data

The OCSP response data decoding is failing

pki

"Check if the configured OCSP server response data"

PKI-5-CERT_ENROLL_RETRY

5-Notice

Certificate reenrollment has failed and retry will happen for [dec] attempts

Automatic certificate re-enrollment failed. We are printing a consolidated message for the maximum number of retry attempts. The router will continue to retry depending on the expiration time of the router's certificate. The retry attempts will be either 999 default or as specified

pki

"Contact the CA administrator. The router will retry."

PKI-4-CERT_ENROLL_RETRY_FAIL

4-Warning

Certificate reenrollment has failed after [dec] attempts

Automatic certificate re-enrollment failed. Caution - Router's Certificate may expire soon.

pki

"Contact the CA administrator. Enrollment failed."

PKI-4-ROUTER_CERT_EXPIRED

4-Warning

Router certificate expired cannot re-enroll/retry for enrollment/re-enroll

Cannot re-enroll/retry for enroll/re-enroll. Caution - Router's Certificate has expired.

pki

"Enroll the router manually."

PKI-4-TRUSTPOOL_DOWNLOAD_FAIL

4-Warning

Trustpool download requires %llu bytes available free storage %llu bytes is insufficient

Trustpool download failed Free space in nvram is not sufficient to store Trustpool Certificates. Change the Trustpool policy for its storage

pki

"Change the storage policy for Trustpool"

PKI-6-TRUSTPOOL_DOWNLOAD_SUCCESS

6-Information

Trustpool Download is successful

Trustpool Download is successful

pki

"No action required. Informational message"

PKI-4-TRUSTPOOL_DOWNLOAD_FAILURE

4-Warning

Trustpool Download failed

Failed to download the trustpool bundle

pki

"Enable debugs and obtain the reason for failure"

PKI-4-TRUSTPOOL_CERTIFICATE_SAVE_CHANGE

4-Warning

Downloaded Trustpool certificates present prior to image upgrade should be re-downloaded. Issue 'crypto pki trustpool import url <url>' to re-download the certificates.

Downloaded Trustpool certificates present prior to image upgrade should be re-downlaoded

pki

"Before image upgrade clean all the downloaded trustpool certificates. Import them again after image upgrade."

PKI-2-NON_AUTHORITATIVE_CLOCK

2-Critical

PKI functions can not be initialized until an authoritative time source like NTP can be obtained.

System clock is not valid. Update the system clock to start with PKI timers

pki

"System clock must be configured/Updated."

PKI-6-AUTHORITATIVE_CLOCK

6-Information

The system clock has been set.

System clock is valid.

pki

"No action. Informational message."

PKI-6-CSR_FINGERPRINT

6-Information

\n CSR Fingerprint MD5 : [chars] \n CSR Fingerprint SHA1: [chars]

Fingerprint display

pki

"Information message"

PKI-6-CERT_ENROLL_AUTO

6-Information

Auto initial enrollment for trustpoint [chars]

Trustpoint enrollment happening automatically.

pki

"No action required. Informational message"

PKI-6-CERT_ENROLL_MANUAL

6-Information

Manual enrollment for trustpoint [chars]

Trustpoint enrollment triggerred manaully

pki

"No action required. Informational message"

PKI-6-CERT_REENROLL

6-Information

Re-enrollment for trustpoint [chars]

Trustpoint re-enrollment triggerred manaully

pki

"No action required. Informational message"

PKI-3-HOSTNAME_RESOLVE_ERR

3-Error

Failed to resolve HOSTNAME/IPADDRESS : [chars]

Unable to resolve hostname/ip-address

pki

"Check network connectivity"

PKI-3-OCSP_CONTENT_MISMATCH

3-Error

ocsp content mismatch

Expected content not matched with formed content

pki

"Check ocsp request"

PKI-2-MEM_ALLOC_FAIL

2-Critical

Memory allocation failure. Number of bytes requested : [dec]

Memory allocation failed

pki

"Check memory left on the device"

PKI-3-SOCKET_OPEN

3-Error

Failed to open socket.

The failure is caused by socket open

pki

"Check tcp/socket debugging message"

PKI-3-SET_SOURCE_INTERFACE_FAIL

3-Error

Failed to set source interface for [chars] ip address

Failed to set source interface

pki

"Check configured source interface for trustpoint"

PKI-3-SOCKET_BIND_FAIL_SOURCE_INTERFACE

3-Error

Failed to bind the socket due to source interface ip : [chars]

Failed to bind socket with source interface

pki

"Check configured source interface for trustpoint"

PKI-3-SET_VRF_FAIL

3-Error

Failed to set VRF : [chars]. VRF not configured

Failed to set VRF

pki

"Check configured VRF for trustpoint and set VRF"

PKI-3-SET_SOCK_VRF_INTERFACE_FAIL

3-Error

Failed to set VRF : [chars] to socket interface

Failed to set VRF to socket

pki

"Check configured VRF for trustpoint and set VRF"

PKI-3-SET_SOCKET_OPTION_FAIL

3-Error

Failed to set socket option. Option : [chars]

Failed to set socket option

pki

"Enable socket debugs"

PKI-3-SOCKET_CONNECT_FAIL

3-Error

Failed to connect to socket

Failed to connect socket

pki

"Enable socket debugs"

PKI-2-CA_SERVER_CERT_EXPIRED

2-Critical

[chars] server ceritifcate expired. Cannot enable [chars] server

CA server certificate expired.

pki

"Reconfigure CA server"

PKI-2-CA_SERVER_LABEL_TOO_LONG

2-Critical

[chars] server name too long. Reconfigure server with name less than 13 characters.

CA server name too long.

pki

"Reconfigure CA server with less than 13 characters"

PKI-2-CA_SERVER_TP_NOT_PRESENT

2-Critical

[chars] server's Trustpoint not available. Check for the trustpoint config.

CA server's Trustpoint not available.

pki

"Check for CA server and Trustpoint configuration presence"

PKI-2-SERVER_TP_CREATE_FAIL

2-Critical

Not abel to create [chars] server's Trustpoint.Check for CA server config's.

CA server's Trustpoint not created.

pki

"Check for CA server and Trustpoint configuration presence"

PKI-2-SERVER_KEY_NOT_PRESENT

2-Critical

Not able to find CS [chars]'s keypair label [chars]. Check whether keypair [chars] is available on device

CA server's key-pair not available.

pki

"Check for key-pair presence"

PKI-2-NON_AUTHORITATIVE_CLOCK_CA

2-Critical

CA server cannot be enabled due to non-authoritative system clock. Configure clock/Sync with NTP server.

System clock is not valid. Update the system clock to start CA server

pki

"System clock must be configured/Updated."

PKI-2-CS_CERT_EXPIRED

2-Critical

Certificate server [chars] CA certificate expired. Regenerate CA certificate manaully.

CS certificate expired.

pki

"Regenerate CS certificate."

PKI-2-CS_CERT_GEN_FAIL

2-Critical

Certificate server [chars] CA certificate generation failed. Regenerate CA certificate manaully.

Certificate Server disabled.

pki

"Regenerate CS certificate."

PKI-2-CS_CERT_INVALID

2-Critical

Certificate server [chars] CA certificate invalid. Regenerate CA certificate manaully.

CS certificate invalid.

pki

"Regenerate CS certificate."

PKI-2-CS_SUBJECT_NAME_FAIL

2-Critical

Extracting subject name from Server certificate failed

Extraction of subject failed

pki

"Regenerate CS certificate."

PKI-2-CS_ISSUER_NAME_INVALID

2-Critical

Invalid issuer_name in CS [chars] configuration

Invalid issuer-name in Certificate Server

pki

"Check certificate server configuration and re-configure."

PKI-2-CS_CERT_NOT_PRESENT

2-Critical

Certificate server [chars]'s certificate not present.

Certificate server certificate not present

pki

"Regenerate CS certificate."

PKI-3-ISSUER_NAME_NOT_BER

3-Error

Issuer name is not BER

Issuer name is not BER. Check issuer-name

pki

"Check issuer-name present/configured"

PKI-3-SUBJECT_NAME_NOT_BER

3-Error

Subject name is not BER

Subject name is not BER. Check subject-name

pki

"Check subject-name present/configured"

PKI-3-CRL_HTTP_FAIL

3-Error

CRL Request over http for trustpoint [chars] failed. \n Reason : [chars]

Receival of CA certificate failed

pki

"CA cert download failed"

PKI-6-CERT_ROLLOVER_ACTIVE

6-Information

A rollover ID certificate has been activated under trustpoint [chars] replacing the previous ID certificate. \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n End-date : [chars]

Rollover ID certificate active

pki

"No action needed. Informational mesage only"

PKI-2-CERT_SHADOW_INSTALL_FAIL

2-Critical

[chars].

Shadow CA/ID certificate installation failed.

pki

"Check for the reason for failure and perform necessary steps"

PKI-6-CERT_SHADOW_INSTALL

6-Information

[chars] \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n End-date : [chars]

Shadow CA/ID certificate has been installed.

pki

"No action needed. Informational mesage only"

PKI-6-CERT_SHADOW_ACTIVE

6-Information

[chars] \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n End-date : [chars]

Shadow CA/ID certificate has been activated.

pki

"No action needed. Informational mesage only"

PKI-3-CERT_ROLLOVER

3-Error

Renew/Shadow event has failed for trustpoint : [chars] \n Reason : [chars]

Renew/Shadow event failed.

pki

"Perform manual renewal of certificate to avoid certificate expiry."

PKI-3-CS_ROLLOVER_TRIGGER

3-Error

CS Rollover event has been triggered for server [chars]

Rollover triggerred for certificate server

pki

"Informational message only. No action needed."

PKI-2-CS_ROLLOVER_FAIL

2-Critical

CS Rollover failed. \n Reason : [chars]

Rollover failed for certificate server

pki

"Critical error on rollover." "Certificate Server has to be re-enabled."

PKI-6-CS_ROLLOVER_AVAILABLE

6-Information

[Sub/RA]CS Rollover certificate has been generated for [chars] and it will be activated at [chars] \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n End-date : [chars]

Rollover certificate generated

pki

"Informational message only. No action needed."

PKI-6-CS_ROLLOVER_ACTIVE

6-Information

[chars] Rollover certificate has been activated for [chars] replacing the previous [Sub/RA]CA certificate \n Issuer-name : [chars] \n Subject-name : [chars] \n Serial-number: [chars] \n End-date : [chars]

Rollover certificate activated

pki

"Informational message only. No action needed."

PKI-3-OCSP_FETCH_FAIL

3-Error

OCSP fetch failed. \n Reason : [chars]

OCSP Fetch failed

pki

"Enable socket/tcp debugs to check connectivity with ocsp server"

PKI-3-OCSP_RESPONSE_FAIL

3-Error

OCSP response from [chars] has been discarded. \n Reason : [chars]

OCSP response parse failed

pki

"Check OCSP response"

PKI-6-OCSP_SUCCESS

6-Information

OCSP response from [chars] has been successfully processed for \n certificate : [chars] \n Serial-number: [chars] \n Result : [chars]

OCSP response successfully processed.

pki

"Informational message only. No action needed."

PKI-2-PKI_EVENT_LOG

2-Critical

PKI Event : [chars]

PKI Event for both success/failure.

pki

"Informational message only. No action needed."

PKI-3-ENROLL_PKCS12

3-Error

Trustpoint [chars] configured as pkcs12 enrollment. SCEP enrollment not supported

Change the trustpoint configuration to point to enrollment-url

pki

"TP configuraiton need to be verified."

PKI-3-GET_CERT_INITIAL

3-Error

Failed with GetCertInitial for trustpoint [chars] \n Reason : [chars]

GetCertInitial encounter fatal error

pki

"Contact the CA administrator."

PKI-6-SLA_TRUSTPOINT_CHANGE

6-Information

Attempting to override SLA Trustpoint. \n The current running SLA trustpoint config will be retained \n Config-Replace errors corresponding to SLA TrustPoint may be \n ingored.

PKI Event for both success/failure.

pki

"Informational message only. No action needed."

PKI-6-TRUSTPOINT_CREATE

6-Information

Trustpoint: [chars] created succesfully

Trustpoint creation is successful

pki

"No action required. Informational message"

PKI-3-MUTUALLY_EXCLUSIVE_CONFIG

3-Error

'grant auto tp <> and grant auto tp-list <> are mutually exclusive config. \n And cannot be configured at same time. Delete one and then \n configure another.

CLI configuration failed

-

"Issue \"no grant auto tp-list\" command to configure "grant auto tp" Or " "Issue \"no grant auto trustpoint\" command to configure "grant auto tp-list.""

PKI-6-TRUSTPOINT_DELETE

6-Information

Trustpoint: [chars] deleted succesfully

Trustpoint deletion is successful

pki

"No action required. Informational message"

PKI-3-PKCS12_IMPORT_FAILURE

3-Error

PKCS #12 import failed for trustpoint: [chars]. Reason: [chars]

A PKCS #12 import got failed

c3pl

"No action required. Informational message"

PPCP-6-WAVL

6-Information

\n[chars] is not successful

The specified classmap or policymap insertion or removal was not succcessful. This is an internal software error.\n

-

LOG_STD_ACTION

PPCP-3-LOCK

3-Error

Can't lock policy provisioning database: [chars]

Access to stored class-maps policy-maps service-policies and related data is protected by a locking mechanism. An operation tried to read or write provisioning data but was unable to get control of the lock.

qos-internal

"Any Cisco Class-based Policy Provisioning Language configuration " "or show commands that you were attempting to " "run may not have succeeded. Please try the operation again.\n\n" "Contact support if this message is seen frequently."

C3PL_TARGET-4- NOREG

4-Warning

No [chars] callback registered for [chars]. Using default function.

A support function for a specific kind of QoS attachment point is not available. A default behavior was applied instead.

C3PL_TARGET_DDTS_COMPONENT

-

CCE_PI_PD-4-TARGET_CLASS_GROUP_DB

4-Warning

Failed to [chars] id %08X [chars] database

An operation to manipulate the record of the target class groups supplied via the PI/PD API has failed to perform the required action on a target class group successfully. This may imply that the resultant notification via the API was deferred or dropped.

cce

"show cce cpdp bindings " "target <id>"

CCE_PI_PD-6-TARGET_BINDINGS_DB

6-Information

[chars] [chars] [chars] target class group %08X contains feature bindings

The target class group is reporting the presence of feature bindings upon its removal. This is informational.

cce

"show cce cpdp bindings " "target <id>"

CCE_PI_PD-4-CLASS_GROUP_DB

4-Warning

Failed to [chars] id %08X [chars] database

An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class group successfully. This may imply that the resultant notification via the API was deferred or dropped.

cce

"show cce cpdp associations " "class-group <id>"

CCE_PI_PD-4-CLASS_DB

4-Warning

Failed to [chars] class group id %08X class id %08X [chars] database

An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class successfully. This may imply that the resultant notification via the API was deferred or dropped.

cce

"show cce cpdp associations " "class group <id>"

CCE_PI_PD-4-CLASS_CLASS_GROUP_DB

4-Warning

Failed to [chars] class group id %08X class id %08X class group %08X [chars] database

An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class group attached to a class successfully. This may imply that the resultant notification via the API was deferred or dropped.

cce

"show cce cpdp associations " "class-group <id>"

CCE_PI_PD-4-FEATURE_BIND_DB

4-Warning

Failed to [chars] target id %08X class group %08X class id %08X feature [chars] binding [chars] database

An operation to manipulate the record of the binding of a action within a policy map class to a particular target supplied via the PI/PD API has failed to perform the required action successfully. This may imply that the resultant notification via the API was deferred or dropped.

cce

"show cce cpdp bindings " "target <id>"

CCE_PI_PD-3-FILTER_LIST

3-Error

Failed to create class [chars] id %08X filter list

An operation to create the filter list for a particular class has failed due to a resource issue. This may imply that the resultant notification via the API was deferred or dropped.

cce

"show class-map [type" " <class type>] <name>"

CCE_PI_PD-6-CLASS_GROUP_CLASSES_DB

6-Information

Class group %08X contains classes

The class group is reporting the presence of classes upon its removal. This is informational.

cce

"show cce cpdp associations " "class-group <id>"

CCE_PI_PD-6-CLASS_CLASSES_DB

6-Information

Class group %08X class %08X [chars] contains a class group

The class is reporting the presence of a class group upon its removal. This is informational.

cce

"show cce cpdp associations " "class-group <id>"

CCE_PI_PD-3-CLASS_NAME

3-Error

Map name [chars] id %08X unable to [chars] string [hec]

-

-

-

CCE_PI_PD-6-CLASS_FILTER

6-Information

Class [chars] id %08X type [chars] filter list is unbalanced

During the addition of a class an internal error was encountered during the construction of the match terms comprising that class.

cce

"show class-map" " [type <type>] <name>"

QOS-3-DETACH

3-Error

Failed to detach [chars] [chars] service policy

The specified type of service policy has failed to detach itself from the attachment point indicated. The service policy will remain attached although repeated attempts to remove such should fail in a similar manner.

c3pl

"show policy-map [type] " "<attachment point>"

QOS-4-SERV_FRAG_POLICY

4-Warning

\nservice-policy [chars] can't be attached without corresponding service-fragment policy on appropriate target first

For a fragment policy that is being installed check if parent targets have relevant service-fragment class installed. If not then we can not allow fragment policy installation.\n

c3pl

"Check the parent target to add relevant service-fragment class.\n"

QOS-6-SUSPEND

6-Information

Suspending service policy [chars] on [chars] in [chars] direction

The interface bandwidth is less than the total bandwidth that is required for QoS policy on this interface.\n

c3pl

"There is no user action required.\n"

QOS-3-TARGET_INDEX

3-Error

[chars] [chars] service policy attachment failed to assign index

The configuration of a service policy has resulted in the failure to generate an internal unique identifier which represents the attachment point target of the associated policy map. This is an

c3pl

LOG_STD_ACTION

QOS-3-UNASSIGNED

3-Error

A [chars] event resulted in an unassigned index for [chars] [chars]

-

-

-

QOS-3-ISSU_GTP_CFG_ENHANCE

3-Error

GTP-AIC configuration has been detected which is totally different with peer. Delete all GTP-AIC related config to proceed with ISSU/ISSD. After ISSU/ISSD done config GTP-AIC again.\n

PEER GTP-AIC configuration would be messed up.

c3pl

"Manually remove all GTP-AIC configuration and reinitiate " "ISSU/ISSD. \n"

QOS-6-POLICY_INST_FAILED

6-Information

Service policy installation failed on [chars]. [chars]. policy:[chars] dir:[chars] ptype:[chars] ctype:[chars]\n

Service policy could not be installed\n

c3pl

"This is an informational message only." "No action is required.\n"

QOS-6-POLICY_REM_FAILED

6-Information

Service policy remove failed on [chars] policy:[chars] dir:[chars] ptype:[chars] ctype:[chars]\n

Service policy could not be removed\n

c3pl

"This is an informational message only." "No action is required.\n"

QOS-3-INVALID_PLTYPE

3-Error

No entry found for pltype : [dec] in global service_policy_queue during service-policy deletion.\n

No entry was found for a pltype when un-queue of a service-policy from global service_policy_queue was undergoing. This will result in freeing a service-policy without un-queuing it from global service_policy_queue.

c3pl

"Need to figure out why there was no entry found for a pltype" " in the global service_policy_queue when passed with a" " service-policy while deletion. check the traceback for" " details"

RPC-3-SOCKET

3-Error

RPC can't create socket

RPC cannot create a socket

rpc

LOG_STD_NO_ACTION

RPC-3-SOCKNAME

3-Error

RPC can't call getsockname

svc_create cannot call getsockname

rpc

LOG_STD_NO_ACTION

RPC-3-AUTH

3-Error

RPC missing authentication

marshal_new_auth cannot authenticate

rpc

LOG_STD_NO_ACTION

RPC-3-SELECT

3-Error

RPC select failed

RPC: cannot call select

rpc

LOG_STD_NO_ACTION

RPC-3-XDRCALLHDR

3-Error

RPC fatal header serialization error

clnt_raw - Fatal header serialization error

rpc

LOG_STD_NO_ACTION

RPC-3-IOCTL

3-Error

RPC ioctl failed

get_myaddress: ioctl failed

rpc

LOG_STD_NO_ACTION

RPC-3-SETSOCKOPT

3-Error

RPC setsockopt failed

pmap_rmt: setsockopt failed

rpc

LOG_STD_NO_ACTION

RPC-3-SENDTO

3-Error

RPC sendto failed

pmap_rmt: sendto failed: cannot send broadcast message

rpc

LOG_STD_NO_ACTION

RPC-3-RECVFROM

3-Error

RPC recvfrom failed

pmap_rmt: recvfrom failed: cannot receive broadcast message

rpc

LOG_STD_NO_ACTION

RPC-3-MALLOC

3-Error

RPC malloc failed

malloc returned NULL

rpc

LOG_STD_NO_ACTION

RPC-3-CLNTPERROR

3-Error

RPC client perror: [chars]

RPC Client perror

rpc

LOG_STD_NO_ACTION

RPC-3-CACHEPERROR

3-Error

RPC cache perror: [chars]

RPC Cache perror

rpc

LOG_STD_NO_ACTION

RPC-3-LSEEK

3-Error

RPC lseek called on a socket

pxdrrec_getpos: This shouldn't happen

rpc

LOG_STD_NO_ACTION

REGISTRY-3-SEQ_LIST_OVERWRITE

3-Error

Attempt made to overwrite a set sequence function [chars]

A single function can be set as a callback for a specified \n\ sequence number for a sequenced list registry. \n\ This message indicates that an attempt to set a new callback has \n\ failed because a callback function has already been set for this \n\ sequence number.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

REGISTRY-3-STUB_CHK_OVERWRITE

3-Error

Attempt made to overwrite a set stub function in [chars].

A single function can be set as a callback for when a stub w/ check\n\ registry is invoked. This message indicates that an attempt to\n\ set a new callback has failed because a callback function\n\ has already been set.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

REGISTRY-3-FASTCASE_OUT_OF_BOUNDS

3-Error

Attempt made in [chars] to register with out of bounds key.

In FASTCASE registry the key has to be smaller than the size specified when the registry was created. This message indicates that an attempt was made to register with a key out of bounds.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

REGISTRY-3-REG_SUSPEND

3-Error

Registry of type SUSPEND called when suspends are not allowed.

When process blocking has been disabled either using\n\ raise_interrupt_level or assign_blocking_disabled\n\ a remote registry of type SUSPEND has been invoked.

remote-registry

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

REGISTRY-3-REG_FLAG_ERR

3-Error

Invalid combination of registry flag and scheduler control : [chars]

When process blocking has been disabled either using\n\ raise_interrupt_level or assign_blocking_disabled a remote registry\n\ with flags REG_FLAG_DATA_SAFE/REG_FLAG_PEER has been invoked.

remote-registry

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

REGISTRY-2-REG_FLAG_DEADLOCK

2-Critical

Registry call to [chars] timed out due to deadlock

-

remote-registry

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

REGISTRY-2-REG_PARSE_ERROR

2-Critical

[chars]: Could not parse notification [chars] : error/no. of items = [dec]

-

remote-registry

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

REGISTRY-3-REG_XDR

3-Error

[chars]

There was an error while marshalling a parameter to a remote\n\ inter-process registry call

remote-registry

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

IPC-2-NOMEM

2-Critical

No memory available for [chars]

The IPC protocol subsystem could not obtain the memory it needed.

ipc

"If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt. To display IPC " "usage enter <CmdBold>show ipc queue<noCmdBold> at the prompt"

IPC-2-TEST

2-Critical

IPC test: [chars]

The IPC test routines.

ipc

"IPC test only - no action required."

IPC-2-INVALIDZONE

2-Critical

Invalid IPC Zone 0x[hec].

Some operation is attempted on a zone ID not known to IPC

ipc

"show tech-support ipc"

IPC-4-GET_PAK_MSG

4-Warning

Failed for message size [dec]

System unable to allocate IPC message of required size.

ipc

"If this error message recurs copy the error message exactly" " as it appears on the console or in the system log contact" " your Cisco technical support representative with the" " gathered information." "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt. To display IPC " "usage enter <CmdBold>show ipc queue<noCmdBold> at the prompt"

IPC-4-CONSISTENCY

4-Warning

Consistency check failed for [chars] 0x[hec]

Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures.

ipc

"show tech-support ipc"

IPC-4-MESSAGE_ERR

4-Warning

Consistency check failed for IPC Message. IPC message 0x[hec] and port information 0x[hec] differ

Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures.

ipc

"show ipc ports"

IPC-5-SLAVELOG

5-Notice

VIP-[chars]

The Cisco IOS software running on a Versatile Interface Processor VIP card generated this message. The error message has been

high-vip

"This is actually a Cisco IOS error message from a VIP. Handle " "it as indicated by the text after the 'VIP-' string in the " "error message."

IPC-5-NODELFUNC

5-Notice

Failed to intialize IPC client

An IPC application cannot be initialized because its initialization\n function does not appear in the IPC initialization list.

ipc

"show tech-support ipc"

IPC-5-NULLDELFUNC

5-Notice

Invalid registration

An IPC application has attempted to register NULL function in the IPC initialization list.

ipc

"show tech-support ipc"

IPC-5-NULL

5-Notice

[chars] [chars]=0x[hec] [chars] 0x[hec]

IPC module could not find an IPC entity that is expected to be existing always

ipc

"show tech-support ipc"

IPC-4-NOPORT

4-Warning

Port Not Found. [hec] --> [hec] Index:[hec] Seq: [dec] flags: [hec] size: [dec]

IPC Received a message which is destined for a port that cannot be found by IPC

ipc

"Capture 'sh ipc status' 'sh ipc ports' and" " 'deb ipc errors' outputs and contact TAC"

IPC-5-MSG_NULL

5-Notice

[chars]

IPC message returned is Null

ipc

"show tech-support ipc"

IPC-5-NULL_HEADER

5-Notice

[chars] MSG: ptr: %p flags: 0x[hec]

IPC message header accessed from IPC message is NULL

ipc

"show tech-support ipc"

IPC-5-INVALID

5-Notice

[chars] Dest Port 0x[hec] Session 0x[hec] Source 0x[hec]

While processing an incoming message IPC encountered invalid data in its internal data structures.

ipc

"show tech-support ipc"

IPC-5-QFULL

5-Notice

Q=0x[hec] [chars] [dec]

IPC queue is full.

os-ipc

LOG_STD_SH_TECH_ACTION

IPC-2-UNLOCK

2-Critical

Unlock done on already unlocked element 0x[hec]

An internal inconsistency was found in some IPC data structures.

ipc

"show tech-support ipc"

IPC-2-LOCK

2-Critical

Lock done a deleted element 0x[hec]

An internal inconsistency was found in some IPC data structures.

ipc

"show tech-support ipc"

IPC-2-CANT_SEND

2-Critical

[chars]: Cannot send IPC message from 0x[hec] to 0x[hec]: info 0x[hec]

An error occurred when sending IPC message

ipc

"show tech-support ipc"

IPC-2-NO_ACK_HANDLER

2-Critical

No handler for ACK with data for port [hec].

The IPC receiver appended data to an ACK. But at the sender there is no corresponding ACK handler.

ipc

"show tech-support ipc"

IPC-2-NODISPATCH

2-Critical

Message for [hec].[hec] has no receive queue or dispatch routine

The IPC user failed to provide any means of handling the received message.

ipc

show ipc ports

IPC-3-DELETED

3-Error

Attempt to delete an IPC message 0x[hec] a second time

-

-

-

IPC-2-ONINT

2-Critical

Invalid operation at interrupt level: [chars] [hec]

Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at the interrupt level.

ipc

show ipc ports

IPC-3-NULL_SESSION

3-Error

unable to process ipc mcast message - no member session for dest_port_info %p group 0x[hec] session [dec] For appclass [chars]

IPC Mcast message has been received for a NULL session

ipc

show ipc mcast session verbose

IPC-2-NOBLOCK

2-Critical

Invalid blocking operation in interrupt context or process blocking is disabled: [chars] [hec]

Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at interrupt level or when process has disabled blocking

ipc

show ipc ports

IPC-3-NOBUFF

3-Error

The [chars] IPC message header cache is empty

The specified IPC message header cache is empty and an incoming IPC message may be dropped as a result.

ipc

"show tech-support ipc"

IPC-3-GIANT

3-Error

Request for giant IPC packet denied. Request size = [dec]

Someone requested a message that was too large for the IPC system

ipc

"show tech-support ipc"

IPC-3-LOWBUFF

3-Error

The main IPC message header cache below application reserve count [dec].

-

-

-

IPC-2-PRECLOSE

2-Critical

IPC port pre-closure overflow : 0x[hec] : 0x[hec]

An application attempts to close an ipc port when there are messages pending in retransmit queue and ipc defer table overflows.

ipc

"show ipc ports open"

IPC-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[dec]

A reference count is used to track the usage of IPC messages. A function increments the count when it begins to use a message and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be zero or negative.

ipc

"show tech-support ipc"

IPC-5-INVALIDINPUT

5-Notice

[chars]

IPC API is called with invalid argument.

os-ipc

LOG_STD_RECUR_ACTION

IPC-5-RPCFULL

5-Notice

Cannot hold RPC message port: [hex] index: [dec] type: [hex]

An RPC request for an application could not be added to the RPC request table because pending requests have filled the RPC request table.

ipc

"show tech-support ipc"

IPC-5-REGPORTFAIL

5-Notice

[chars] [chars]=0x[hec] [chars]=0x[hec]

Several IPC messages are pending to be processed. If the number increases it may result in the IPC header cache or buffers being exhausted.

ipc

"show tech-support ipc"

IPC-2-NOBOOL

2-Critical

Boolean NULL in IPC message: [hec].

A watched boolean that was allocated while sending the message is found to be NULL when an ACK arrived.

ipc

show ipc status

IPC-5-NOCALLBACK

5-Notice

[chars]: Flow control callback function is not provided by IPC Client [chars]

An IPC application cannot be controlled if flow need to be slowed down. This might result in drop of IPC packets

ipc

"show ipc ports"

IPC-3-APP_IPC_FAIL

3-Error

[chars] failed. IPC Error: [chars] [dec]

IPC Application Process failed to do some operation with the IPC Layer. The message includes the error code from ipc layer

ipc

show ipc status

IPC-3-ISSU_ERROR

3-Error

[chars] failed with error code [dec] for seat [hec]

ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library

os-ipc

show issu fsm

IPC-3-ISSU_API_ERR

3-Error

[chars] failed with error code [dec]

ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library

os-ipc

show issu client

IPC-5-NULLBPHANDLER

5-Notice

Passed Null backpressure handler

The maximum message timeout for an IPC message exceeds 2 minutes

ipc

"Capture 'sh version' and contact TAC"

IPC-5-SEND_APP_MSG_FAILED

5-Notice

Send message to peer for [chars] failed. Reason: [chars]

Client using IPC App Port has not been able to send message

ipc

"If the reason is 'no such port' then this may be caused because" " of the difference in the versions of IOS running on Active" " and the standby. Any other reason please collect 'sh ipc stat'" " 'sh ipc rpc' 'sh ipc port' on active and standby RPs and " " contact tac"

IPC-6-STATEFUL

6-Information

[chars]

A Stateful IPC Event occurred

ipc

"This is not a bug but just an informational message."

IPC-2-INITFAILED

2-Critical

[chars]

IPC Resource Management Initialization failed

ipc

"This is a critical failure for IPC functionality." "Capture 'sh version' and contact TAC"

IPC-6-MAXRPCTIMEOUT

6-Information

Maximum RPC timeout value [dec] seconds set for port 0x[hec]

The maximum RPC timeout for an IPC message exceeds the maximum expected value of 10 minutes

ipc

"Capture 'show techsupport ipc' and contact TAC"

IPC-6-KEEPALIVE

6-Information

Rcvd keepalive from seat 0x[hec] msglen=[dec]

An IPC Keepalive message sent for every 10 sec

ipc

"This is normal behavior"

IPC-2-INVALIDSEAT

2-Critical

Invalid IPC Seat 0x[hec].

Some operation is attempted on a seat ID not known to IPC

ipc

"show tech-support ipc"

IPC-2-SPI_IOSD_IPC_INIT_FAILED

2-Critical

SPI IOSd IPC init failed - [chars].

SPI IOSd IPC initialization failed

spi

"show tech-support ipc"

IPC-5-FC_ON

5-Notice

SEAT FC is turned on for Seat [hec] Port ID [hec] Port Index [dec] Portinfo [hec] Last sent [dec] Last Heard [dec] Last xmitted [dec] Last Ack [dec] Ack Pending [dec] Last Ack xmitted [dec]

SEAT FC is being turned on Wait for it to be turned off .

ipc

"show tech-support ipc"

IPC-5-FC_OFF

5-Notice

SEAT FC is turned off for Seat [hec] Port ID [hec] Port Index [dec] Portinfo [hec] Last sent [dec] Last Heard [dec] Last xmitted [dec] Last Ack [dec] Ack Pending [dec] Last AckXmitted [dec]

SEAT FC is being turned off

ipc

"show tech-support ipc"

-

5-Notice

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

5-Notice

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

OER_MC-6-INFO

6-Information

NULL

-

oer

""

OER_MC-5-NOTICE

5-Notice

NULL

-

oer

""

OER_MC-4-WARNING

4-Warning

NULL

-

oer

""

OER_MC-3-ERROR

3-Error

NULL

-

oer

""

OER_MC-1-ALERT

1-Alert

NULL

-

oer

""

OER_MC-0-EMERG

0-Emergency

NULL

-

oer

""

PFR_MC-1-ALERT

1-Alert

[chars]

-

pfr

""

PFR_MC-3-INTERNAL_ERROR

3-Error

[chars]:[chars]

-

pfr

""

PFR_MC-3-VERSION_MISMATCH

3-Error

[chars]

-

pfr

""

PFR_MC-3-WARNING

3-Error

[chars]

-

pfr

""

PFR_MC-5-MC_STATUS_CHANGE

5-Notice

MC is [chars]

-

pfr

""

PFR_MC-5-BR_STATUS_CHANGE

5-Notice

BR [chars] [chars]

-

pfr

""

PFR_MC-5-INTERFACE_STATUS_CHANGE

5-Notice

BR [chars] [chars] IF [chars] [chars]

-

pfr

""

PFR_MC-5-ROUTE_EVENT

5-Notice

[chars]

-

pfr

""

PFR_MC-5-COST_MINIMIZATION

5-Notice

[chars]

-

pfr

""

PFR_MC-5-TOP_TALKER_STATUS

5-Notice

[chars]

-

pfr

""

PFR_MC-5-EXPORT_STATUS_CHANGE

5-Notice

[chars]

-

pfr

""

PFR_MC-5-PBR_STATUS_CHANGE

5-Notice

[chars]

-

pfr

""

PFR_MC-5-OOP_LINK

5-Notice

[chars]

-

pfr

""

PFR_MC-6-OOP_ACTIVE_MODE

6-Information

[chars]

-

pfr

""

PFR_MC-6-OOP_PASSIVE_MODE

6-Information

[chars]

-

pfr

""

PFR_MC-6-ROUTE_EVENT_INFO

6-Information

[chars]

-

pfr

""

OER_TT_FLOW-2-OER_TT_FLOW_BR_EXPORTINIT

2-Critical

Error initializing OER TT Flow BR Export queue

Initialization of the OER TT Flow BR export queue could not be accomplished because of a low memory condition.

-

"Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

OER_TT_FLOW-2-OER_TT_FLOW_BR_CACHEINIT

2-Critical

Error initializing OER TT Flow BR cache

Initialization of the OER TT Flow BR cache could not be accomplished because of a low memory condition.

-

"Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

OER_TT_FLOW-4-OER_TT_FLOW_BR_FLOWEXPORT

4-Warning

Error exporting [chars]

flows to RP

-

LOG_STD_DBG_ACTION

OER_BR-3-INTERNAL_ERROR

3-Error

[chars]:[chars]

-

PfR

""

OER_BR-6-INFO

6-Information

NULL

-

oer

""

OER_BR-5-NOTICE

5-Notice

NULL

-

oer

""

OER_BR-4-WARNING

4-Warning

NULL

-

oer

""

OER_BR-3-ERROR

3-Error

NULL

-

oer

""

OER_BR-1-ALERT

1-Alert

NULL

-

oer

""

PFR_BR-1-ALERT

1-Alert

[chars]

-

pfr

""

PFR_BR-3-INTERNAL_ERROR

3-Error

[chars]:[chars]

-

pfr

""

PFR_BR-4-WARNING

4-Warning

[chars]

-

pfr

""

PFR_BR-5-BR_STATUS_CHANGE

5-Notice

[chars]

-

pfr

""

PFR_BR-5-MC_STATUS_CHANGE

5-Notice

MC [chars] is [chars]

-

pfr

""

NETWORK_RF_API-6-IDB_TRANSITIONS_PENDING

6-Information

Switchover terminated with [dec] transitions pending after there was no transition activity for [dec] seconds

The system terminated the switchover idb transitioning phase with a number of idb transitions still pending because no switchover related IDB transitions were logged during the specified time interval. Some connected routes may experience a temporary loss of traffic.

ha-idb-sync

LOG_STD_NO_ACTION

NETWORK_RF_API-3-FAILSENDMSGTOSTDBY

3-Error

Failed to send [chars] message to standby for [chars] rc=[dec]

The specified synchronization message which is an internal IPC message could not be sent to the standby unit in the specified run-time module. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the type of failure. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-FAILSENDMSGTOACTIVE

3-Error

Failed to send [chars] message to active for [chars] [chars]

The specified synchronization message which is an internal IPC message could not be sent to the active unit in the specified run-time module. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-FAILDECODEDATADESC

3-Error

Cannot decode data descriptor for [chars] descriptor type=[chars]

An internal data descriptor could not be decoded for synchronization for the interface or controller in the run-time module specified in the message output. The failure most likely occurred because of a software error. The descriptor type specified in the message output identifies the type of descriptor the failure occurred with. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

"show redundancy idb-sync-history"

NETWORK_RF_API-3-NO_MSG_BUFFER

3-Error

No message buffer for [chars]

A message data buffer that is used for state synchronization could not be obtained. An internal data structure could not be allocated for synchronization in the run-time module specified in the message output. The failure most likely occurred because of a software error or a lack of system memory. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

"If you determine that this condition was caused by " "a lack of system memory reduce system activity to " "ease memory demands or if conditions warrant upgrade " "to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-NO_CHKPT_BUFFER

3-Error

No checkpointing buffer for [chars] rc=[dec]

A message data buffer that is used for state synchronization could not be obtained. An internal data structure could not be allocated for synchronization in the run-time module specified in the message output. The return code that is specified in the message output identifies the type of failure. The failure most likely occurred because of a software error or a lack of system memory. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

"If you determine that this condition was caused by " "a lack of system memory reduce system activity to " "ease memory demands or if conditions warrant upgrade " "to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-INVALID_MSG_RECEIVED

3-Error

Invalid [chars] message received

A message that is used for state synchronization was not received correctly. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-INVALID_CHKPT_STATUS_CODE

3-Error

Invalid checkpointing status code received rc=[dec]

An invalid checkpoint status code has been detected. An internal status code that is associated with checkpointing was found to be invalid. The return code that is specified in the message output identifies the invalid code that was detected. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-CLIENT_REGISTER_FAIL

3-Error

Failed to register with [chars] rc =[dec]

A redundancy client could not be registered. An internal failure associated with client registration occurred in the run-time module specified in the message output. The return code that is specified in the message output identifies the type of failure that was detected. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-NO_RESOURCES

3-Error

[chars]

A run-time module could not obtain the resources that are required to complete a task. The failure most likely occurred because of a software error or a lack of system memory. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

"If you determine that this condition was caused by " "a lack of system memory reduce system activity to " "ease memory demands or if conditions warrant upgrade " "to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-ISSU_REG_SES_INFO

3-Error

Failed to register ISSU session information: [chars]

The system failed to register the ISSU session information required to complete version exchange between the active and standby units. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-ISSU_UNREG_SES_INFO

3-Error

Failed to register ISSU session information: [chars]

The system failed to unregister the ISSU session information required to complete version exchange between the active and standby units. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-ISSU_START_NEGO_SES

3-Error

Failed to start ISSU session: [chars]

The system failed to start the ISSU negotiation session required to complete version exchange between the active and standby units. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-ISSU_MSG_TYPE_INCOMPAT

3-Error

The active and standby ISSU message types are incompatible

A message that is used for state synchronization is deemed to be incompatible. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-ISSU_TRANSFORM_FAIL

3-Error

The ISSU message [chars] transformation failed: [chars]

A message that is used for state synchronization could not be transformed correctly. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-ISSU_MSG_MTU_INVALID

3-Error

The ISSU message MTU is invalid: [chars]

A message buffer size that is used for state synchronization was found to be invalid. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_SH_TECH_ACTION

NETWORK_RF_API-3-CHKPT_ENTITY_FAIL

3-Error

A checkpointing entity [chars] operation failed rc=[dec]

An internal operation that is associated with checkpointing failed. The return code that is specified in the message output identifies the type of failure. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

"Issue 'show checkpoint entities' and " "'show checkpoint clients' to " "determine the problem"

PACKET-3-INITFAIL

3-Error

Packet server initialization failed. Reason : [chars]

The packet subsystem was not able to initialize properly

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-RESTARTFAIL

3-Error

Packet server restart failed. Reason : [chars]

The packet subsystem was not able to restart properly

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-PTHREADMUTEXFAIL

2-Critical

pthread_mutex_init failed on packet mutex. Reason : [chars]

The packet manager failed to initialize the global mutex

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-CHUNKCREATEFAIL

2-Critical

chunk_create for [chars] pool failed

The packet manager encountered a chunk creation failure\n\ while creating the packet header chunk

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-HDRPOOLINITFAIL

2-Critical

Packet header pool init failed

Failed to initialize the packet pool headers

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-ENQUEUEFAIL

2-Critical

Fail to insert client %ld into pak_client_list at [chars]

Mutex operation failed in the packet server

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-DEQUEUEFAIL

2-Critical

Fail to remove client %ld from pak_client_list at [chars]

Can not remove the client from client list queue. \n\ This may cause the client fail to reconnect to packet \n\ server

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-GETNODENAMEFAIL

2-Critical

failed to get node name in pakman server init

packet manager server unable to retrieve the hostname for node/linecard

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-INITWARNING

3-Error

Warning[chars] while initializing the packet process

-

-

-

PACKET-2-CHANCREATEFAIL

2-Critical

Packet server fails to create a channel and event manager error: [chars]

Packet server fails to create an event manager and \n\ channel. Clients will be unable to connect to packet \n\ server and packet server will be unable to send and \n\ receive messages.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-EVENTATTACHFAIL

2-Critical

event attach failure

The packet subsystem encountered an error when \n\ registering for synchronous or asynchronous events.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-PTHREADCREATEFAIL

2-Critical

pthread create fail in pakman while creating the [chars] thread

packet manager server unable to create a new thread

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-EVENTCONTEXTALLOCFAIL

2-Critical

event_context_alloc failure

Failed while allocating the event context

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-EVENTBLOCKFAIL

2-Critical

event_block failure

event block error was encountered when blocking for external events

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-SHMCREATEFAIL

2-Critical

Error in creating the shared buffer mem: [chars]

Fatal error encountered while creating shared packet buffers

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-SHMCTLFAIL

2-Critical

Error in shm_ctl: [chars]

Fatal error encountered while doing the shm_ctl operations on the shared packet memory

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-ACCESSERROR

2-Critical

Client process %ld attempted to access packet [hec] owned by process %ld

A packet manager client can only access and modify packets that have been assigned to its process

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-CONNECTFAIL

2-Critical

Client process %ld failed to connect to Packet Manager reason [chars]

-

-

-

PACKET-2-REDZONEERROR

2-Critical

Client process %ld has packet 0x%8x the buffer 0x%8x \n\ has been overrun.

Data has been written past the end of the buffer causing\n\ memory to be corrupted.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-BLOCKERROR

2-Critical

Client process %ld has packet 0x%8x the buffer 0x%8x has been corrupted.

Data has been written past the end of the previous \n\ buffer causing memory to be corrupted.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-NEXTBLOCKERROR

2-Critical

The next block after buffer 0x%8x packet 0x%8x has been corrupted.

-

-

-

PACKET-2-CTXERROR

2-Critical

The context information 0x%8x is not valid.

An application to the memory block manager has passed\n\ either a context pointer that is not valid.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-MEMBLKERROR

2-Critical

Memory block 0x%8x is not valid.

An application to the memory block manager has passed\n\ a memory block that is not valid.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-MEMFREEERROR

2-Critical

Memory block 0x%8x has already been freed.

An application to the memory block manager has attempted\n\ to free or lock a memory block that is not allocated.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-MEMTWINBLKERROR

2-Critical

An attempt to coalesce memory block 0x%8x with its\n\ sibling memory block 0x%8x has failed because the sibling\n\ block is not valid.

An attempt to coalesce two memory blocks\n\ has failed because a memory block is not valid.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-2-MEMORDINALERROR

2-Critical

The memory block manager has detected an ordinal error.\n\ Memory block 0x%8x has an ordinal of 0x%4x and a size of 0x%4x.\n\ Its corresponding lower sibling memory block 0x%8x has\n\ an ordinal of 0x%4x and a size of 0x%4x.

The lower sibling ordinal should be equal to the\n\ difference between the higher sibling's ordinal and\n\ size.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-REFCOUNTERROR

3-Error

Bad reference count in packet: %p refcount: [dec].

An attempt was made to free a packet that\n\ has already been freed

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-IFINPUTCOUNTERROR

3-Error

Packet: %p with linktype:[dec] being punted from process: %ld to process: %ld with out decrementing the input_qcount

An attempt was made to punt the packet from one process\n\ to another with the input queue flag set. This means that\n\ the input_qcount was not decremented on the interface \n\ where the packet was received. This will lead to input\n\ queue throttling on that interface

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-PAK_INPUTQ_ERROR

3-Error

Packet: %p in process: %ld has PAK_INPUTQ set incorrectly

A packet outside the iosbase has the input queue \n\ flag set. This means that a packet was punted from \n\ the iosbase to another ION process without decrementing \n\ the input queue count

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-REINITSHMEM

3-Error

Restarting [chars] to reinitialize shared memory because of memory corruption\n

There has been a memory corruption. Restart the \n\ client to reinitialise shared memory.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-CLNTDISCONN

3-Error

Handling disconnect for client [dec] [chars]\n

-

-

-

PACKET-3-CORRUPTPAKHDR

3-Error

Corruption in packet header [hec] pid [dec] magic [hec] buffer [hec] caller_pc [hec]\n

The packet header has become corrupted.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-ERRPAKHDR

3-Error

Not able to fix corruption in packet header [hec] pid = [dec]\n

There has been a corruption in the packet header memory\n\ and it cannot be fixed.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-CORRUPTPAKPOOL

3-Error

[chars] Pool [hec] corrupted magic [hec]\n

The packet pool has failed a consistency check as it \n\ has got corrupted.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-BLKDUMP

3-Error

[chars]

This is just to report general messages in the memory\n\ management code.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-PACKETHDRDUMP

3-Error

[chars]

This is just to report general packet header messages.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET-3-RECOVERBLK

3-Error

\nBLOCK 0x[hec] IS SUCESSFULLY RECOVERED AFTER CORRUPTION\n

Corruption was detected in a memory block and it \n\ was posible to recover the block successfully.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

PACKET_SRVCS-3-PARTICLEPAKDUPFAIL

3-Error

Particle packet duplication attempted on non-particle packet\n

Duplication of packet with particles routine is called\n\ without the packet containing particles.

packetmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

INTERFACE_API-4-BADSWIDB

4-Warning

[chars] may not be referencing the correct swidb

An internal software error occurred.

Obtain from traceback.

LOG_STD_RECUR_ACTION

INTERFACE_API-4-BADPAKINPUT

4-Warning

pak->if_input is not initialized

An internal software error occurred.

Obtain from traceback.

LOG_STD_RECUR_ACTION

INTERFACE_API-1-NAMESTRTOOLONG

1-Alert

Interface name [chars].[dec] exceeded maximum allowed length [dec]

An internal software error occurred.

idb

LOG_STD_ACTION

INTERFACE_API-3-NOADDSUBBLOCK

3-Error

The [chars] subblock named [chars] was not added to [chars]

A software error has occured this message is displayed when IDB subblocks cannot be added.

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-3-INVALIDSUBBLOCKPARAMETERS

3-Error

Invalid subblock parameters for [chars] were supplied.

An internal software error occurred.

idb

"Copy the error message exactly as it appears on the console or in " "the system log. Issue the show idb and show tech-support " "commands to gather data that may help identify the nature of " "the error. Also perform a search of the Bug Toolkit " BUG_TOOLKIT "." "If you still require assistance open a case with the " "Technical Assistance Center via the Internet " TAC_CASE_OPEN " or contact your Cisco technical support representative and " "provide the representative with the gathered information."

INTERFACE_API-3-SUBNUMDBERR

3-Error

subnum [hec] error in [chars]

A software error has occured this message is displayed when a problem has occured with a sub_number db.

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-1-NOMORESWIDB

1-Alert

No more SWIDB can be allocated maximum allowed [dec]

No more Interfaces can be created because the maximum number \n\ of SWIDB allowed for this platform has been reached

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-1-NOMORE_HASWIDBS

1-Alert

No more IDBS can be created. \nThe maximum allowed numbers [dec] has been reached on Standby \nPlease force redundancy mode to RPR if full Active Capacity [dec] is needed

No more Software IDB numbers can be Created. The maximum allowed numbers has been reached for this High Available System.\n

idb

-

INTERFACE_API-1-NOMOREHWIDBNUMBERS

1-Alert

No more hardware IDB numbers can be issued. The maximum allowed numbers [dec] has been reached for this platform.\n

No more hardware IDB numbers can be issued. The maximum allowed numbers has been reached for this platform.\n

idb

"In addition to the following copy the information " "from <CmdBold>show idb<NoCmdBold>. " LOG_STD_ACTION

INTERFACE_API-1-NOMORESWIDBNUMBERS

1-Alert

No more software IDB numbers can be issued. The maximum allowed numbers [dec] has been reached for this platform.\n

No more software IDB numbers can be issued. The maximum allowed numbers has been reached for this platform.\n

idb

"In addition to the following copy the information " "from <CmdBold>show idb<NoCmdBold>. " LOG_STD_ACTION

INTERFACE_API-4-BADPAKOUTPUT

4-Warning

pak->if_output is not initialized on interface [chars]

An internal software error occurred.

Obtain from traceback.

LOG_STD_RECUR_ACTION

INTERFACE_API-4-BADPOINTER

4-Warning

Function [chars] detected an invalid [chars] pointer of %08lX ignoring

A software error has occurred this message is displayed when \n\ an invalid pointer is detected.

Obtain from traceback.

"LOG_STD_SH_TECH_ACTION"

INTERFACE_API-3-NODESTROYSUBBLOCK

3-Error

The [chars] subblock named [chars] was not removed

A software error has occured this message is displayed when \n\ IDB subblocks cannot be removed.

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-3-CANNOTGETMTU

3-Error

Error [dec] received while getting MTU: [chars]. Using default [dec]

A software error has occurred while attempting to retrieve the MTU value from the interface.

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-3-NOSUBBLOCK

3-Error

[chars] subblock does not exist on interface [chars]

An internal software error occurred.

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-4-TBLERROR

4-Warning

A error occurred while using the Index Table utility for [chars].

-

Obtain from traceback.

LOG_STD_ACTION

INTERFACE_API-3-BADIDBSTATUSCHANGECALL

3-Error

Invalid function call at interrupt level.

An internal function was illegally called at interrupt level. This error might be caused by incorrectly coded creation or deletion of an interface or during an OIR operation.\n

idb

"Perform a search of the Bug Toolkit " BUG_TOOLKIT "." "If you still require assistance copy the error message " "exactly as it appears on the console or in the system log. " "Issue the <CmdBold>show tech<NoCmdBold> command and copy the " "output. If you performed any actions before the error message " "appeared make a note of this. Open a case with the Technical " "Assistance Center via the Internet " TAC_CASE_OPEN " or contact " "your Cisco technical support representative and provide the " "representative with the gathered information."

INTERFACE_API-3-IFNUMTOIDBERROR

3-Error

Error occurred while using the ifnum to idb table for interface [chars] if number [dec] during [chars]

A software error has occurred. This message is displayed when an operation on the if_number to idb mapping table could not be performed successfully.

idb

LOG_STD_ACTION

INTERFACE_API-3-HWIDBQREENTRANT

3-Error

[chars] in progress of being inserted/removed ignoring new request to [chars]

A software error has occurred while attempting to insert or remove the interface into the system as there's already another attempt in progress to insert or remove this interface. The first attempt must complete before a new attempt can be started. The user should retry this operation at a later time.

idb

LOG_STD_ACTION

VIDB-3-FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

idb

LOG_STD_ACTION

VIDB-3-FREETIMENOTSET

3-Error

Value not specified for vidb forcible free time by platform.

Platform has requested for delayed vidb recycling support but hasn't specified any value for forcible free time.

Log DDTS against platform.

LOG_STD_ACTION

IDB_IDENTITY-3-MALLOC

3-Error

Memory allocation failure for HWIDB type [dec]

A memory allocation failure occured when trying to allocate the identity for this HWIDB. This HWIDB will not be allocated an IF Index which will prevent it from being used for forwarding data.

ha-ifindex-sync

LOG_STD_ACTION

IDB_SGI-2-XDRREG

2-Critical

[chars]

An internal software error occurred.

idb

LOG_STD_ACTION

IDB_SGI-2-MEMREQ

2-Critical

[chars]

An internal software error occurred.

idb

LOG_STD_ACTION

IDB_SGI-3-BADPTR

3-Error

[chars] of interface with ifindex [dec] is invalid

An internal software error occurred.

Owners of the interface

LOG_STD_ACTION

IDB_SGI-3-MEMFAIL

3-Error

[chars]

An internal software error occurred.

idb

LOG_STD_ACTION

IDB_SGI-4-MEMBERREQ

4-Warning

member request failure for interface with ifindex [dec]\n returned err - [chars]

An internal software error occurred.

sgi

LOG_STD_ACTION

IDB_SGI-3-XDRREQ

3-Error

[chars]

An internal software error occurred.

xdr

LOG_STD_ACTION

IDB_SGI-4-INTERR

4-Warning

[chars] for interface with ifindex [dec]

An internal software error occurred.

idb

LOG_STD_ACTION

IDB_SGI-4-UNEXPINP

4-Warning

[chars]

An internal software error occurred.

idb

LOG_STD_ACTION

IDBINDEX_SYNC-3-IDBINDEX_INITKEY

3-Error

Cannot initialize interface index table lookup key: \[chars]\ [dec]

An internal software error has occurred.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-IDBINDEX_RETRIEVE

3-Error

Cannot retrieve if-index for this interface: \[chars]\ [dec] [chars] [chars]

The interface index number was not found in the interface index table for the interface specified in the error message. This condition might have been caused by the interface index number not being properly synchronized by the primary processor card.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-VALIDATE

3-Error

Cannot validate if-index for this interface: \[chars]\ [dec] [chars] [chars]

The identity of this interface could not be validated against the stored identity within the IDB Index table. This condition is likely to have occured due to the identity of the IDB changing without first explicitly unlinking the previous identity.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-IDBINDEX_ASSIGN

3-Error

Failed to assign an index to IDB type [dec] for interface \[chars]\ rc=[dec]

An IF-Index can not be allocated for this interface due to an internal software error. This is an unrecoverable error that results in this interface not being usable for traffic.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-IDBINDEX_LINK

3-Error

Driver for IDB type '[dec]' changed the Identity of interface \[chars]\ without deleting the old Identity first rc=[dec]

The IF-Index Table can not be updated with the new Identity provided for this interface due to an internal software error. Most likely the old Identity was not deleted first by the driver or that the driver accidentily changed the Identity.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-IDBINDEX_ENTRY_MISMATCH

3-Error

An interface index mismatched its active table entry: \[chars]\ type [dec] table index=[dec] interface index=[dec]

An interface index was found which didn't match the active interface index table entry with the corresponding sync key due to an internal software error.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-RF_ERR

3-Error

[chars] [dec] .

The interface index sync RF client has an error.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-IPC_ERR

3-Error

[chars]: [chars] in domain [dec].

The interface index sync IPC session has error.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-ISSU_ERR

3-Error

[chars][chars] rc=[dec]

The interface index sync ISSU client has error.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-INIT_ERR

3-Error

[chars]

The interface index sync ISSU client has an initialization error.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-4-TRUNCATE

4-Warning

Overflow in [chars] when encoding interface sync key got [dec] maximum is [dec]

When creating a unique sync key to represent an interface it has been detected that one of the attributes making up the key was truncated to fit in the allocated space in the key. This may lead to overlapping key allocations which would cause an error.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-TRANSFORM

3-Error

Require IF-Index ISSU transformation function [chars] [chars]

IF-Index Sync has identified a missing ISSU transformation function which may lead to unpredictable results. This must be resolved before the code is released.

IDBINDEX_SYNC_DDTS_COMP

"Contact IF-Index Sync development team with the contents of the " "configuration and error message so that the driver may be identified."

IDBINDEX_SYNC-4-RESERVE

4-Warning

Failed to lookup existing ifindex for an interface on the Standby allocating a new ifindex from the Active ifindex=[dec] idbtype=[chars]

Encountered a lookup failure for an interface on the Standby. An attempt has been amde to resolve the issue by reserving a possibly new ifindex on the Active. If this situation was encountered due to a defect in the key encoding then traffic may stop on this interface should the system switchover.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC-3-LIST_REMOVE

3-Error

Failed to remove node from the if-index entry list

When an if-index lookup failed on the Standby the process waits on timer till the standby receives the if-index or the timer expires To know which processes are waiting a list will be maintained and when any of the above mentioned events occured the corresponding node from the list will be removed

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION

IDBINDEX_SYNC_KEY-3-UNKNOWN_TYPE

3-Error

Interface type is unknown and cannot be synced: \[chars]\ [dec]

An internal software error has occurred.

IDBINDEX_SYNC_DDTS_COMP

LOG_STD_ACTION

POWERNET_ISSU-3-INIT

3-Error

EnergyWise ISSU client initialization failed to [chars]. Error: [dec] [chars]

EnergyWise ISSU client could not be initiailzed. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

powernet

LOG_STD_SH_TECH_ACTION

POWERNET_ISSU-3-TRANSFORM_FAIL

3-Error

EnergyWise ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

EnergyWise ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the EnergyWise state between the active device and the standby device is not identical.

powernet

"show issu session <client_id> and" "show issu negotiated version <session_id>"

POWERNET_ISSU-3-MSG_NOT_OK

3-Error

EnergyWise ISSU client 'Message Type [dec]' is not compatible

EnergyWise ISSU client received an incompatible message from the peer device. The message cannot be processed.

powernet

"show issu message group <client_id> and" "show issu session <client_id> and" "show issu negotiated version <session_id>"

POWERNET_ISSU-3-MSG_SIZE

3-Error

EnergyWise ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

EnergyWise ISSU client failed to calculate the MTU for the specified message. The EnergyWise ISSU client is not able to send the message to the standby device.

powernet

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

POWERNET_ISSU-3-INVALID_SESSION

3-Error

EnergyWise ISSU client does not have a valid registered session.

EnergyWise ISSU client does not have a valid registered session.

powernet

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

POWERNET_ISSU-3-SESSION_REGISTRY

3-Error

EnergyWise ISSU client failed to register session information. Error: [dec] [chars]

EnergyWise ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

powernet

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

POWERNET_ISSU-3-SESSION_UNREGISTRY

3-Error

EnergyWise ISSU client failed to unregister session information. Error: [dec] [chars]

EnergyWise ISSU client failed to unregister session information.

powernet

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

POWERNET_ISSU-3-SESSION_NEGO

3-Error

EnergyWise ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The EnergyWise ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

powernet

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

POWERNET_ISSU-3-SEND_NEGO_FAILED

3-Error

EnergyWise ISSU client failed to send negotiation message. Error: [dec] [chars]

EnergyWise ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device can not be brought up properly.

powernet

"show logging and show checkpoint client"

POWERNET_ISSU-3-GET_BUFFER

3-Error

EnergyWise ISSU client failed to get buffer for message. Error: [dec] [chars]

EnergyWise ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiaiton the standby device cannot be brought up properly.

powernet

"show logging and show checkpoint client"

POWERNET_ISSU-3-CAPABILITY

3-Error

Powernet ISSU client [chars]

Powernet ISSU client observed an error during capability negotiation. When this error happens there is a mismatch between the client capability between the active and standby unit.

powernet

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

POWERNET_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

Powernet ISSU client capability exchange result incompatible.

The Powernet ISSU client capability exchange has negotiated as incompatible with the peer.

powernet

"show issu negotiated capability <Session_ID>"

POWERNET_ISSU-3-CAP_INVALID_SIZE

3-Error

Powernet ISSU client capability list is empty.

The Powernet ISSU client capability exchange list size is invalid.

powernet

"show issu capability entries <Client_ID>"

SSH-3-KEYPAIR

3-Error

Attempt to generate server keys failed - error code: [chars]

Server RSA key-pair could not be generated.

ssh

"If this message recurs contact your technical support representative."

SSH-3-PRIVATEKEY

3-Error

Unable to retrieve RSA private key for [chars]

RSA private key does not exist or is corrupted.

ssh

"If this message recurs contact your technical support representative."

SSH-5-ENABLED

5-Notice

SSH [dec].[dec] has been enabled

The SSH protocol has been enabled for connections

ssh

"No action necessary - informational message"

SSH-5-DISABLED

5-Notice

SSH [dec].[dec] has been disabled

The SSH protocol has been disabled for connections

ssh

"No action necessary - informational message"

SSH-4-DEATTACK

4-Warning

CRC-32 compensation attack detected src [inet] dst [inet] attack thwarted. Connection is closed.

CRC-32 compensation vulnerability allows an attacker to execute arbitrary commands on the SSH server or otherwise subvert an encrypted SSH channel with arbitrary data. for more information on this attack see http://www.core-sdi.com/english/ssh

ssh

"No action necessary - attack has been thwarted"

SSH-3-PROC_MISMATCH

3-Error

SSH [chars] Incorrect process waiting for event. Process name: [chars]

An incorrect process has entered ssh wait for event ideally only SSH Process on the server or Exec process on the client are allowed to wait for event through ssh

ssh

"No action necessary - informational message"

SSH-5-SSH_SESSION

5-Notice

SSH Session request from [chars] tty = [dec] using crypto cipher '[chars]' [chars]

The SSH session request information

ssh

"No action necessary - informational message"

SSH-5-SSH2_SESSION

5-Notice

SSH2 Session request from [chars] tty = [dec] using crypto cipher '[chars]' hmac '[chars]' [chars]

The SSH session request information

ssh

"No action necessary - informational message"

SSH-5-SSH_USERAUTH

5-Notice

User '[chars]' authentication for SSH Session from [chars] tty = [dec]

The SSH user authentication status information

ssh

"No action necessary - informational message"

SSH-5-SSH2_USERAUTH

5-Notice

User '[chars]' authentication for SSH2 Session from [chars] tty = [dec]

The SSH user authentication status information

ssh

"No action necessary - informational message"

SSH-5-SSH_CLOSE

5-Notice

SSH Session from [chars] tty = [dec] for user '[chars]'

The SSH Session closure information

ssh

"No action necessary - informational message"

SSH-5-SSH2_CLOSE

5-Notice

SSH2 Session from [chars] tty = [dec] for user '[chars]'

The SSH Session closure information

ssh

"No action necessary - informational message"

SSH-4-SSH2_UNEXPECTED_MSG

4-Warning

Unexpected message type has arrived. Terminating the connection from [chars]

SSH Session closure warning on receiving an inappropriate message from the peer

ssh

"If this message recurs contact your technical support representative."

SSH-3-NOMEMORY

3-Error

Memory allocation failed.

A Malloc has failed during SSH execution

ssh

"System seems to be running low on memory if this " "message recurs please contact your technical " "support representative"

SSH-3-BUFF_LEN_EXCD

3-Error

Buffer Length exceeded

Tried to allocate or append a buffer beyond its maximum length

ssh

LOG_STD_ACTION

SSH-3-BUFF_GET_FAIL

3-Error

Tried to get more bytes than in SSH Buffer

Tried to retrieve more data than actually present in the buffer

ssh

LOG_STD_ACTION

SSH-3-BIG_NUM_BIG

3-Error

Big num error: Cannot handle big num of size [dec]

Key operations tried to retrieve a big num of too large a value

ssh

LOG_STD_ACTION

SSH-3-STRING_NULL

3-Error

Tried to append NULL string to buffer

A function tried to append a NULL string to buffer or packet which shouldn't happen

ssh

LOG_STD_ACTION

SSH-3-PACK_SND_FAIL

3-Error

Packet send failed

A packet send failed within ssh code

ssh

LOG_STD_ERROR

SSH-3-NO_KEX

3-Error

No Kex cannot rekey

Rekey failed failed to get kex information

ssh

LOG_STD_ACTION

SSH-3-KEX_SHORT

3-Error

Kex proposal too short

Key exchange failed as the kex proposal was too short

ssh

LOG_STD_ACTION

SSH-3-NO_MATCH

3-Error

No matching [chars] found: client [chars] server [chars]

The specified entity cipher or mac or comp algo etc was not found please check the corresponding parameter and try again

ssh

"If you believe you are incorrectly receiving this " "message please contact your " "technical support representative"

SSH-3-NOT_SUPP

3-Error

Matching [chars] not supported: [chars]

The specified entity cipher or mac or comp algo etc is not supported by IOS SSH

ssh

"If you believe you are incorrectly receiving " "this message please contact " "your technical support representative"

SSH-3-KEX_NOT_SUPP

3-Error

Unsupported key exchange method: [dec]

The key exchange type proposed is not supported by IOS SSH. Kindly check the SSH settings to verify the group used.

ssh

"Kindly check the SSH settings to verify the " "key exchange method used. Or contact your technical support " "representative for any help"

SSH-3-NO_DH_GRP

3-Error

Non Standard DH Group aborting key exchange

Non standard DH group sent hence aborting key exchange kindly verify your SSH parameters

ssh

"Kindly check the SSH settings to check the key " "exchange group used. Or contact your technical " "support representative for further help"

SSH-3-KEY_GEN_FAIL

3-Error

DH key generation failed. Status [dec]

DH key generation failed

ssh

LOG_STD_ACTION

SSH-3-HOSTKEY_FAIL

3-Error

Cannot load hostkey

Hostkey load has failed causing dh key negotiations to fail

ssh

LOG_STD_ACTION

SSH-3-DH_SIZE

3-Error

DH public key size > DH group key size[dec]

DH negotiation failed due to size mismatch between public key size and group size

ssh

LOG_STD_ACTION

SSH-3-DH_SECRET_FAIL

3-Error

DH shared secret computation failed status [dec]

DH secret value computation failed this is required in DH negotiation cannot move on hence aborting

ssh

LOG_STD_ACTION

SSH-3-RSA_SIGN_FAIL

3-Error

Signature [chars] failed status [dec]

RSA Signature creation/verification failed

ssh

LOG_STD_ACTION

SSH-3-ECDSA_SIGN_FAIL

3-Error

Signature [chars] failed status [dec]

ECDSA Signature verification failed

ssh

LOG_STD_ACTION

SSH-3-DH_RANGE_FAIL

3-Error

Client DH key range mismatch with [chars] configured DH key on server

DH Range mismatch with min/max configured DH key on server DH negotiation failed

ssh

LOG_STD_ACTION

SSH-3-INV_MOD

3-Error

Invalid modulus length

Invalid modulus length

-

-

SSH-3-INV_CONN

3-Error

Invalid Connection Block

Invalid Connection Block

ssh

LOG_STD_ACTION

SSH-3-INCOMP_DH

3-Error

Incompatible DH Proposal from Server

Incompatible DH proposal received from server cannot proceed

ssh

LOG_STD_ACTION

SSH-3-SER_NOT_DEF

3-Error

ServerHostKey not defined in SSH Server Database

Server Host key is not present in SSH Server Database causing host key verification to fail

ssh

LOG_STD_ACTION

SSH-3-SER_VAL_FAIL

3-Error

ServerHostKey Validation failed. Key Mismatch

ServerHostKey Validation failed. Key Mismatch

ssh

LOG_STD_ACTION

SSH-3-CIPH_INIT_FAIL

3-Error

Cipher initialization failed

Cipher initialization failed failed to set new keys

ssh

LOG_STD_ACTION

SSH-3-BAD_PACK_LEN

3-Error

Bad packet length [dec]

Bad packet length packet decompose failed

ssh

LOG_STD_ACTION

SSH-3-PACK_PADD_ERR

3-Error

Padding error: needed [dec] bytes block size [dec] bytes mod= [dec]

Padding error packet decompose failed

ssh

LOG_STD_ACTION

SSH-3-PACK_CORR_PAD

3-Error

Corrupted padlen [dec] on input

Packet with corrupted padd length received causing packet decompose to fail

ssh

LOG_STD_ACTION

SSH-3-NO_CHANNEL

3-Error

Non-existent channel [dec]

Non-existent channel id received

ssh

LOG_STD_ACTION

SSH-3-PACK_INTEG_ERROR

3-Error

Packet integrity error [dec] bytes remaining from [chars]

Packet error incorrect amount of data received

ssh

LOG_STD_ACTION

SSH-3-AUTH_METH_ERR

3-Error

Server does not support password or keyboard-interactive authentication

No common supported authentication methods exist

-

-

SSH-3-SERVER_AUTH_METH_ERR

3-Error

Server does not support/Configured with '[chars]' Authentication method

No common supported authentication methods exist

ssh

LOG_STD_ACTION

SSH-3-RANDOM_GEN_FAIL

3-Error

Unable to generate random number

Random number generation error

ssh

"If this message recurs contact your technical support representative."

SSH-3-IDLE_TIMEOUT

3-Error

Idle timeout due to no response from the remote machine

No response from the remote machine

ssh

LOG_STD_ACTION

SSH-3-LOCAL_RST

3-Error

Local Reset happened due to line termination/disconnection

Line termination or request for a disconnection

ssh

LOG_STD_ACTION

SSH-3-NO_USERAUTH

3-Error

No auth method configured for SSH [chars]. Incoming connection from [chars] tty = [dec] dropped

At least one auth method should be configured for SSH server

ssh

"Please configure at least one auth method. " "If this message recurs contact your technical support representative."

SSH-3-DH_GEX_RANGE_OUT

3-Error

Server has chosen DH group size which is not in range [dec] !< [dec] !< [dec] DH Group Exchange key negotiation failed

Server must choose DH group size which falls between client sent min/max

ssh

"If this message recurs contact your technical support representative."

SSH-5-SSH_COMPLIANCE_VIOLATION_RSA_KEY_SIZE

5-Notice

SSH RSA Key Size compliance violation detected. Kindly note that the usage of keys smaller than [dec] bits will be deprecated in the upcoming releases. Please revise your key configuration accordingly to avoid service impact.

SSH user is hereby informed about the impending deprecation of the RSA key size that is currently employed and is advised to effect the required configuration changes to avoid the possibility of service impact in the future.

ssh

"This is an informational message and can be " "dismissed. At the same time it is highly recommended that the user " "makes required configuration changes at the earliest to avoid service " "impacts upon software upgrades."

SSH-5-SSH_COMPLIANCE_VIOLATION_ENCR_ALGO

5-Notice

SSH Encryption Algorithm compliance violation detected. Kindly note that the usage of Algorithm type '[chars]' will be deprecated in the upcoming releases.Please configure alternate encryption algorithms to avoid service impact.

SSH user is hereby informed about the impending deprecation of the encryption algorithm that is currently employed and is advised to effect the required configuration changes to avoid the possibility of service impact in the future.

ssh

"This is an informational message and can be " "dismissed. At the same time it is highly recommended that the user " "makes required configuration changes at the earliest to avoid service " "impacts upon software upgrades."

SSH-5-SSH_COMPLIANCE_VIOLATION_PK_ALGO

5-Notice

SSH Public-key Algorithm compliance violation detected.Kindly note that weaker Public-key Algorithm '[chars]' will be disabled by-default in the upcoming releases.Please configure more stronger PK algorithms to avoid service impact.

SSH user is hereby informed about the impending removal of public key algorithm from default PK list that is currently employed and is advised to effect the required configuration changes to avoid the possibility of service impact in the future.

ssh

"This is an informational message and can be " "dismissed. At the same time it is highly recommended that the user " "makes required configuration changes at the earliest to avoid service " "impacts upon software upgrades."

PASSWD-5-AUTH_INVALID_PASSWORD

5-Notice

[chars] [chars] Failed authentication

The credential did not match the configured value when authentication

passwd

"No action required"

PASSWD-5-AUTH_REPEATED_FAILURE

5-Notice

[chars] [chars] number of allowed dauthentication failure exceeded

The number of authentication failures the allowed interval excceeded the configured value

passwd

"No action required"

PASSWD-5-AUTH_LIFETIME_EXCEEDED

5-Notice

[chars] [chars] credential lifetime has expired

The credential has exceeded the configured lifetime

passwd

"No action required"

PASSWD-5-AUTH_PRE_EXPIRY_NOTIFY

5-Notice

[chars] [chars] The credential is about to expiry

The credential is within to pre-expireinterval change the credential expires

passwd

"No action required"

PASSWD-5-CREDENTIAL_COMPLEXITY_CHECK_FAILED

5-Notice

[chars] [chars] credential has failed the complexty check

The credential may not be as secure since it has failed the complexity check

passwd

"No action required"

PASSWD-5-CREDENTIAL_PASSWORD_CHANGE_EXCEED_LIMIT

5-Notice

[chars] [chars] the number of changes allowed has been exceeded

The number of credential changes has exceed the configured number and interval

passwd

"No action required"

IKEV2-5-OSAL_INITIATE_TUNNEL

5-Notice

NULL

-

ipsec-ikev2

-

IKEV2-5-RECV_CONNECTION_REQUEST

5-Notice

NULL

-

ipsec-ikev2

-

IKEV2-3-NEG_ABORT

3-Error

NULL

-

ipsec-ikev2

-

IKEV2-1-SEND_COOKIE_CHALLENGE

1-Alert

NULL

-

ipsec-ikev2

-

IKEV2-5-IPSEC_COLLISION

5-Notice

NULL

-

ipsec-ikev2

-

IKEV2-5-SA_UP

5-Notice

NULL

-

ipsec-ikev2

-

IKEV2-5-SA_DOWN

5-Notice

NULL

-

ipsec-ikev2

-

IKEV2-5-SA_REJECTED_RESOURCE_LOW

5-Notice

NULL

-

ipsec-ikev2

-

IKEV2-5-SA_REJECTED_LIMIT_REACHED

5-Notice

[chars]

-

ipsec-ikev2

-

IKEV2-5-INCREASE_PEER_WINDOW_SIZE

5-Notice

NULL

-

ipsec-ikev2

-

TLSCLIENT-5-UPDOWN

5-Notice

Session [%p] to TLSGW: [[chars]] is [chars]

TLS Tunnel service state changed.

-

LOG_STD_NO_ACTION

TLSCLIENT-5-REKEY_CONN_FAILURE

5-Notice

Rekey failed for Session [%p] to TLSGW [[chars]]

This message indicates that the Rekey for the tunnel to the tlsgw failed.

-

"Either the server is down or the connectivity to the server" " is broken"

CRYPTO-6-AUTOGEN

6-Information

Generated new [dec] bit key pair

Auto-Enroll has generated a new router key pair

-

"No action required. Informational message"

CRYPTO-3-RSA_SELFTEST_FAILED

3-Error

Generated RSA key failed self test

An automatic test of the newly generated RSA keypair [chars] failed. That RSA key was automatically deleted.

-

"File a DDTS. As an immediate workaround attempt to create another pair"

CRYPTO-3-ECDSA_SELFTEST_FAILED

3-Error

Generated ECDSA key failed self test

An automatic test of the newly generated ECDSA keypair [chars] failed. That ECDSA key was automatically deleted.

-

"File a DDTS. As an immediate workaround attempt to create another pair"

CRYPTO-4-RECVD_PKT_NOT_IPSEC

4-Warning

Rec'd packet not an IPSEC packet. ip vrf/dest_addr= [chars]/[inet] src_addr= [inet] prot= [dec]

Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated. IPSEC Peer is sending unencapsulated packets. There may simply be a policy setup error on the peer. Some might consider this a hostile event.

-

"Contact the peer's administrator to compare policy settings."

CRYPTO-4-RECVD_PKT_NOT_IPSEC_V6

4-Warning

Rec'd packet not an IPSEC packet. ip vrf/dest_addr= [chars]/[chars] src_addr= [chars] prot= [dec]

-

-

-

CRYPTO-3-POLICY_CKSUM_ERROR

3-Error

Crypto policy checksum failure.\n \tCrypto access list [chars] crypto map [chars] interface [chars]\n

Crypto policy checksum failure has been detected in this router whose traffic is protected by the crypto policy. This event may be caused by memory corruption occuring in crypto policy data or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event the router has been forced to reload.

-

"Contact your Cisco support representatives."

CRYPTO-4-RECVD_PKT_INV_UDP_WRAPPER

4-Warning

Rec'd packet has invalid udp wrapper protocol.\n \tcryptoflags = [hec] sa->udp_wrapper_support = [dec] transform = [hec]

Rec'd packet either udp encapsulated but is not correct negotiation transform. Or it expected an udp encapsulated packet but it received a non-udp packet. There may simply be a policy setup error on the peer. Some might consider this a hostile event.

-

"Contact the peer's administrator to compare policy settings."

CRYPTO-4-RECVD_PKT_INV_CTCP_WRAPPER

4-Warning

Rec'd packet has invalid cTCP wrapper protocol.\n \tcryptoflags = [hec] sa->udp_wrapper_support = [dec] transform = [hec]

Rec'd packet either cTCP encapsulated but is not correct negotiation transform. Or it expected an cTCP encapsulated packet but it received a non-cTCP packet. There may simply be a policy setup error on the peer. Some might consider this a hostile event.

-

"Contact the peer's administrator to compare policy settings."

CRYPTO-4-RECVD_PKT_INV_SPI

4-Warning

decaps: rec'd IPSEC packet has invalid spi for destaddr=[chars] prot=[dec] spi=0x[hec][dec] srcaddr=[chars]

Rec'd IPSEC packet specifies SPI that doesn't exist in SADB. This may be a temporary condition due to slight differences in aging of SAs between the IPSEC peers or it may be because the local SAs have been cleared. It may also be because of bogus packets sent by the IPSEC peer. Some might consider this a hostile event.

-

"If the local SAs have been cleared the peer may not know" " this. In this case if a new connection is established" " from the local router the two peers may reestablish " " successfully. Otherwise if the problem occurs for more than " " a brief period either attempt to establish a new connection " " or contact the peer's administrator."

CRYPTO-4-RECVD_PKT_INV_PROT

4-Warning

decapsulate: packet missing [chars] destadr=[inet] actual prot=[dec]

Rec'd IPSEC packet missing an expected AH or ESP header The peer is sending packets that don't match the negotiated security policy. Some might consider this a hostile event.

-

"Contact the peer's administrator."

CRYPTO-4-RECVD_PKT_MSG_LEN_ERR

4-Warning

decapsulate: packet has bad [chars] length destadr=[inet] prot=[dec] len=[dec]

Rec'd IPSEC packet is malformed: possibly encapsulation error? The peer is sending malformed packets. It may be due to a decryption error. Some might consider this a hostile event.

-

"Contact the peer's administrator."

CRYPTO-4-RECVD_PKT_INV_IDENTITY

4-Warning

[chars]\n \tip dest_addr= [inet] src_addr= [inet] prot= [dec]\n

Decapsulated IPSEC packet not maching negotiated identity The peer is sending other traffic through this SA. It may be due to an SA selection error by the peer. Some might consider this a hostile event.

-

"Contact the peer's administrator to compare policy settings."

CRYPTO-4-RECVD_PKT_INV_IDENTITY_ACL

4-Warning

ipsec check access: identity not allowed by ACL\n \tip dest_addr= [inet] src_addr= [inet] prot= [dec]\n

After all is said and done the decaps packet fails the ACL check The peer is sending other traffic through this SA. It may be due to an SA selection error by the peer. Some might consider this a hostile event.

-

"Contact the peer's administrator to compare policy settings."

CRYPTO-4-PKT_REPLAY_ERR

4-Warning

[chars]\n \tconnection id=[dec] sequence number=%lu\n

Replay processing failed. This may be a temporary condition due to waiting for new SAs to be established. In the inbound case this may also be due to an actual replay attack. Some might consider this a hostile event.

-

"If the problem appears to be more than a transient one" " contact the peer's administrator."

CRYPTO-4-IKMP_INVALID_POLICY

4-Warning

ISAKMP policy rsa-encr not supported by crypto HW accelerator [chars]

rsa-encr is not supported by Hifn based crypto HW accelerators

-

"Use ISAKMP policy rsa-sig"

CRYPTO-4-RECVD_PKT_MAC_ERR

4-Warning

decrypt: mac verify failed for connection id=[dec][chars]

MAC verify processing failed. This may be due to the use of the wrong key by either party during the MAC calculations. Some might consider this a hostile event.

-

"Contact the peer's administrator."

CRYPTO-4-RECVD_PKT_FAIL_DECOMPRESS

4-Warning

pcp: [dec] byte packet failed to decompress pcp: dest_addr=[inet] src_addr=[inet]

The received IPPCP packet failed to decompress. This may be due to a decompression buffer error.

-

LOG_STD_ACTION

CRYPTO-6-IKMP_AUTH_FAIL

6-Information

Authentication method [dec] failed with host [chars]

The IKE process was unable to authenticate its security Association with its remote peer.

-

"Contact the remote peer's administrator."

CRYPTO-4-IKMP_ISR_LIMIT_MAX

4-Warning

INV SPI RECOV LIMIT [dec] maxed [chars] [chars] [chars]

INVALID SPI RECOVERY SAs maximum limit has been reached.

-

"Possibly the local box reloaded."

CRYPTO-5-IKMP_SETUP_FAILURE

5-Notice

IKE SETUP FAILED for local:[chars] local_id:[chars] remote:[chars] remote_id:[chars] IKE profile:[chars] fvrf:[chars] fail_reason:[chars] fail_class_cnt:%ld

IKE Negotiation Failed.

-

"LOG_STD_ACTION"

CRYPTO-5-IPSEC_SETUP_FAILURE

5-Notice

IPSEC SETUP FAILED for local:[chars] local_id:[chars] remote:[chars] remote_id:[chars] IKE profile:[chars] fvrf:[chars] fail_reason:[chars] fail_class_cnt:%ld

IPSec Negotiation Failed.

-

"LOG_STD_ACTION"

CRYPTO-4-IKMP_PKT_OVERFLOW

4-Warning

ISAKMP message from [chars] larger %ld than the UDP packet length %ld

-

-

-

CRYPTO-4-IKMP_NO_SA

4-Warning

IKE message from [chars] has no SA and is not an initialization offer

IKE maintains state for a communication in the form of security associations. No security association exists for this packet and it is not an initial offer from the peer to establish one. This situation could denote a denial of service attack.

-

"Contact the remote peer and/or his administrator"

CRYPTO-6-IKMP_UNK_EXCHANGE

6-Information

IKE peer at [chars] sent a message with unknown exchange [dec]

IKE preforms actions on messages based on defined exchanges. The message received had an unknown exchange.

-

"Contact the remote peer's administrator"

CRYPTO-6-IKMP_BAD_DOI_SA

6-Information

DOI value [dec] from SA offer from [chars] is invalid

The DOI field of an SA offer defines how to parse the fields SAs with an unknown DOI cannot be parsed

-

"If this situation persists contact the remote peer's administrator"

CRYPTO-6-IKMP_BAD_CERT_USE

6-Information

Certificate for peer at [chars] prohibits attempted use [chars].

X.509v3 certificates can contain usage restrictions. These can restrict use of the certificate only for signatures or only for key exchange encryption. The peer attempted to

-

"Contact the remote peer and the remote peer's CA"

CRYPTO-5-IKMP_INVAL_CERT

5-Notice

Certificate received from [chars] is bad: [chars]

The certificate given by remote peer has either been revoked or expired certificate invalid or the signature check on the

-

"Contact the CA of the remote peer. Possibly bad CA certificate."

CRYPTO-6-IKMP_NO_ID_CERT_DN_MATCH

6-Information

NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate DN with [chars]

ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the distinguished name of the peer's certificate.

-

"Contact the remote peer if this situation persists"

CRYPTO-6-IKMP_NO_ID_CERT_ADDR_MATCH

6-Information

NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate addr with [chars]

ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the ip address of the peer's certificate.

-

"Contact the remote peer if this situation persists"

CRYPTO-6-IKMP_NO_ID_CERT_FQDN_MATCH

6-Information

NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate fqdn with [chars]

ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the fqdn of the peer's certificate.

-

"Contact the remote peer if this situation persists"

CRYPTO-6-IKMP_NO_ID_CERT_USER_FQDN_MATCH

6-Information

NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate user fqdn with [chars]

ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the user fqdn of the peer's certificate.

-

"Contact the remote peer if this situation persists"

CRYPTO-6-IKMP_BAD_DOI_NOTIFY

6-Information

DOI of [dec] in notify message from [chars]

The DOI field in notify messages give the receiver a context in which to understand the message being notified. This DOI value is not understood and the message therefore cannot be understood.

-

"If this situation persists contact the remote peer."

CRYPTO-4-IKMP_BAD_MESSAGE

4-Warning

IKE message from [chars] failed its sanity check or is malformed

A quick sanity check is done on all received ISAKMP messages to verify that all component payload types are valid and that the sum of their individual lengths equals the total length of the received message. This message failed the sanity check. Persistantly bad messages could be a denial of service attack or bad decryption.

-

"Contact the remote peer's administrator."

CRYPTO-6-IKMP_SA_NOT_OFFERED

6-Information

Remote peer [chars] responded with attribute [chars] not offered or changed

IKE peers negotiate policy by the initiator offering a list of possible alternate protection suites. The responder responded with one that the initiator did not offer

-

"Contact the remote peer"

CRYPTO-6-IKMP_MODE_FAILURE

6-Information

Processing of [chars] mode failed with peer at [chars]

Negotiation with the remote peer failed.

-

"If this situation persists contact the remote peer"

CRYPTO-6-IKE_TED_BAD_REPLY

6-Information

Received TED reply that did not correspond to a TED probe

Rec'd TED reply that does not match a TED probe we currently have outstanding. This may be a one time occurance due to the TED reply being delayed. It may also be because of ill-formed packets sent by the peer. Some might consider this a hostile event.

-

"If the problem occurs more than once contact the peer's" " administrator."

CRYPTO-6-IKMP_CRYPT_FAILURE

6-Information

IKE connection id [dec] unable to [chars] packet

Encryption or decryption on a particular IKE thread failed.

-

"Contact remote peer"

CRYPTO-6-IKMP_NOT_ENCRYPTED

6-Information

IKE packet from [chars] was not encrypted and it should've been.

A portion of the IKE exchange takes place in the clear and a portion is encrypted. This message should have been encrypted but was not.

-

"Contact remote peer"

CRYPTO-6-IKMP_SA_NOT_AUTH

6-Information

Cannot accept Quick Mode exchange from [chars] if SA is not authenticated!

The IKE security association with the remote peer was not authenticated yet the peer attempted to begin a Quick Mode exchange. This exchange must only be done with an authenticated security association

-

"Contact remote peer"

CRYPTO-6-IKMP_ADD_KEY_FAIL

6-Information

Unable to add public key for [chars] %15i to key ring

Keys are stored in keyrings on the router. An attempt to add another key to the ring failed.

-

"Check local key rings. This is probably due to other failures."

CRYPTO-6-IKMP_POLICY_DEFAULT

6-Information

Using ISAKMP Default policies

Since the user has not configured any ISAKMP policies and default ISAKMP policies are enabled then use default ISAKMP policies for negotiation

-

""

CRYPTO-4-AUDITWARN

4-Warning

Encryption audit check could not be performed

The audit check verifying encryption entitlement within the IOS image could not be performed due to incompete system configuration.

-

"Manually verify that this IOS image is entitled to contain " "encryption."

CRYPTO-0-AUDITFAIL

0-Emergency

Encryption audit check found the wrong level of encryption in this image

The audit check verifying encryption entitlement within the IOS image either found encryption in a non-encryption image or the wrong strength within an IOS image containing encryption. Use of the encryption may violate U.S. Export Laws and Regulations.

-

"Contact Cisco to obtain a replacement IOS image."

CRYPTO-0-SELF_TEST_FAILURE

0-Emergency

Encryption self-test failed [chars]

One of the encryption self-tests has failed. The encryption engine is not operable in this state.

-

"If the failure persists contact Cisco to " "obtain a replacement IOS image."

CRYPTO-6-SELF_TEST_RESULT

6-Information

Self test info: [chars]

This audit prompt the results of Cryptographical seltftests

-

"This message is for information only. No action is" " required."

CRYPTO-3-IKEINIT

3-Error

[chars]

An IKE initialization error

ipsec

LOG_STD_ACTION

CRYPTO-3-IKE_PAK_IN_Q_TIME_LIMIT_EXCEED

3-Error

Pak spent too much time in the IKE input queues

An incoming IKE packet spent too much time in the IKE input\n\ queues. This can happen when the IKE subsystem is under heavy\n\ load due to a lot of peers trying to setup SAs simultaneously\n\ and IKE is not able to handle all the incoming packets in a\n\ timely manner.

-

"It is important to understand why many peers are simultaneously\n\ trying to setup SAs at the same time. If possible try to avoid\n\ or minimize such network conditions."

CRYPTO-3-IKMP_PEER_INIT_FAILURE

3-Error

IKE failed to create IKE peer tree or leaf node.

IKE failed to allocate memory for the IKE peer tree

-

"More DRAM may be required in order to run the image."

CRYPTO-6-RANDOM

6-Information

A pseudo-random number was generated twice in succession by [chars]

A pseudo-random number generator produced the same number twice\n\ in succession.

ipsec

"Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative."

CRYPTO-6-PRNG_SEED_KEY_ERROR

6-Information

Pseudo-random number generator seed and seed key was identical

The X9.17 random number specification requires us to check for\n\ the same value appearing as the seed and the seed key. This\n\ message indicates that the condition was discovered.

ipsec

"The X9.17 random number will occasionally produce this condition\n\ and this is not a problem. However if this message occurs frequently\n\ the system should be manually reloaded. If the message is persistent\n\ across reloads copy the error message exactly as it appears and\n\ report it to your technical support representative."

CRYPTO-6-PRINTABORT

6-Information

[chars] caused early termination of show output[chars]

While showing a list the list was changed or elements changed. This can happen if SA's are re-negotiated at the time the show-command was paused or if someone reconfigured or cleared SA's amongst other things. This is not an error but a side-effect of a dynamic system.

ipsec

"In general this is merely a warning that the " "output from the show command is most likely incomplete. " "Re-running the show-command should provide the newest " "information. On a busy system with ever-changing SA's " "this may appear frequently."

CRYPTO-3-BADMAGIC

3-Error

Bad [chars] magic number %04x.

An internal software error.

ipsec

LOG_STD_ACTION

CRYPTO-6-ISAKMP_MANUAL_DELETE

6-Information

IKE SA manually deleted. Do 'clear crypto sa peer [chars]' to manually clear IPSec SA's covered by this IKE SA.

The IKE SA was deleted by user command. However keepalives this connection are enabled and IPSec SA's covered by this IKE SA still exist. Since this IKE SA is now deleted these IPSec SA's have no IKE SA covering them. The recommended action is to manually delete this IPSec SA's.

ipsec

"Use parser command "clear crypto sa" to clear " "IPSec SA's."

CRYPTO-4-IKE_QUICKMODE_BAD_CERT

4-Warning

encrypted connection attempted with a peer without the\n configured certificate attributes

An encrypting peer attempted to establish an IPSec session with an interface which it was not authorized for. Some might consider this a hostile event.

-

"Check if the peer should be authorized to connect with the" " IPSec connection. If he should be allowed it may be a" " configuration issue. Otherwise you should contact the" " peer's administrator."

CRYPTO-6-CET_END_OF_LIFE

6-Information

CET connection msg in an IPSEC_ONLY_IMAGE

CET has been End-of-lifed in IOS release 12.21

CSCds60123

""

CRYPTO-4-TRANSFORM_NOT_SUPPORTED

4-Warning

\nTransform [chars] is not supported with the current hardware configuration.\nGlobal transform [chars] will be deleted.

System configuration modified.Some ipsec transforms which were earlier valid with software crypto are no longer valid now after switching hardware crypto.

-

"Create valid transform sets & update cryptomaps"

CRYPTO-4-REM_CRYPTOMAP_TS

4-Warning

\nPlease recheck your crypto map [chars].

Transform set entry removed from crypto-map as it is no longer valid with hardware crypto engine enabled.

-

"Create and apply valid transform set to cryptomap"

CRYPTO-4-ENC_METHOD_NOT_SUPPORTED

4-Warning

Invalid encryption method for IKE policy [dec]

Configured encryption method is not supported

-

"Use any of the valid encryption methods for the ISAKMP policy"

CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED

4-Warning

Transform [chars] not valid under IPSec transform [chars]

Configured encryption algorithm not supported

-

"Specify a valid encryption algorithm for the ipsec transform"

CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_WITH_IKE

4-Warning

Transform [chars] not usable with IKE because of IPSec transform [chars]

Configured encryption algorithm not uable with IKE with current hardware configuration

-

"If you need to negotiate this with IKE specify a valid encryption " "algorithm for the ipsec transform"

CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_FULL_SPEED

4-Warning

Transform [chars] will run with reduced performance because of IPSec transform [chars]

Configured encryption algorithm will not run on the hardware encryption card. The transform is still usable but will run with reduced performance.

-

"If you need to use the full performance of the encryption card " "specify another encryption algorithm for the ipsec transform"

CRYPTO-4-IPSEC_AAA_START_FAILURE

4-Warning

IPSEC Accounting was unable to send start record

The AAA subsystem was unable to send the accounting start on behalf of IPSec. This could be due to the AAA Server being unreachable.

ipsec

"Ensure that the AAA server is reachable and enabled" "for accounting."

CRYPTO-4-IPSEC_AAA_STOP_FAILURE

4-Warning

IPSEC Accounting was unable to send stop record

The AAA subsystem was unable to send the accounting stop on behalf of IPSec. This could be due to the AAA Server being unreachable.

ipsec

"Ensure that the AAA server is reachable and enabled" "for accounting."

CRYPTO-6-LLQ_OVERSUBSCRIBE

6-Information

Sum of priority class bandwidth exceeds crypto engine's throughput for small packets crypto b/w=[dec] kbps allocated b/w=[dec] kbps.

The crypto engine may be oversubscribed by priority class traffic. This happens when the user tries to provision more priority class bandwidth than what the crypto engine can handle. If each class is sending at its max rate some priority packets may be dropped

-

"Reduce the priority class bandwidth or reduce" "the number of priority classes in the policy-map"

CRYPTO-4-IA_CLEARTEXT

4-Warning

Unencrypted traffic [chars] [inet] because crypto optional is configured

Cleartext traffic is passing through an interface that is configured for encryption. This traffic is accepted because the router has the CRYPTO IPSEC OPTIONAL ENABLE setting which allows such traffic.

ipsec

"If you did not intend to configure the crypto " "optional setting you should reconfigure the box " "to turn it off"

CRYPTO-4-IA_ENABLE

4-Warning

Security warning: crypto ipsec optional is configured

Currently the router has the CRYPTO IPSEC OPTIONAL ENABLE setting which allows data which normally would be encrypted to be sent in the clear.

ipsec

"If you did not intend to configure the crypto " "optional setting you should reconfigure the box to turn " "it off"

CRYPTO-5-SESSION_STATUS

5-Notice

Crypto tunnel is [chars]. Peer [chars]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars]

-

-

-

CRYPTO-5-IKEV2_SESSION_STATUS

5-Notice

Crypto tunnel v2 is [chars]. Peer [chars]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars]

This is a notification message for IPSEC tunnel status

-

"No action is required"

CRYPTO-5-IPSEC_SA_HA_STATUS

5-Notice

IPSec sa's if any for vip [inet] will change from [chars] to [chars]

This is a notification message for crypto ipsec sa's changing their HA status

ipsec-ha

"No action is required"

CRYPTO-5-IKE_SA_HA_STATUS

5-Notice

IKE sa's if any for vip [inet] will change from [chars] to [chars]

This is a notification message for crypto ike sa's changing their HA status

ipsec-ha

"No action is required"

CRYPTO-3-ENGINE_BAD_ID

3-Error

Crypto Engine id [dec] is invalid

The packet has its engine_id set to something other than software crypto or hardware crypto. Unable to determine which crypto engine to use The packet will be default sent to software crypto engine.

ipsec

"No action required"

CRYPTO-6-ISAKMP_ON_OFF

6-Information

ISAKMP is [chars]

The ISAKMP process has been switched on or off either by CLI or because no crypto map or EzVPN configuration is applied to any interface.

ipsec-isakmp

"No action required."

CRYPTO-6-GDOI_ON_OFF

6-Information

GDOI is [chars]

The ISAKMP/gdoi process has been switched on or off either by CLI or because no GDOI crypto map or Key Server is applied to any interface.

ipsec-getvpn

"No action required."

CRYPTO-6-TOKENINSERTED

6-Information

Cryptographic token [chars] inserted in [chars]

A cryptographic token has been detected

-

"Informational message only. No action required."

CRYPTO-6-TOKENREMOVED

6-Information

Cryptographic token [chars] removed from [chars]

A cryptographic token has been detected

-

"Informational message only. No action required."

CRYPTO-6-TOKENTIMEOUTCANCELLED

6-Information

Cryptographic Token [chars] re-inserted. removal timeout cancelled

A cryptographic token containing private key files has been re-inserted in time. Router RSA keypairs and associated IPSEC sessions will be NOT be deactivated

-

"Informational message only. No action required."

CRYPTO-4-TOKENKEYTIMEOUT

4-Warning

RSA keypairs for token [chars] and associated IPSEC sessions will be deactivated in [dec] seconds

Router RSA keypairs and associated IPSEC sessions will be deactivated when the timeout expires

pki

"Re-insert the crypto token before the timeout expires"

CRYPTO-4-TOKENKEYSDEACTIVATED

4-Warning

RSA keypairs from token [chars] and associated IPSEC sessions being deactivated now

Router RSA keypairs and associated IPSEC sessions are being deactivated because the token containing them was removed

pki

"Re-insert the crypto token"

CRYPTO-4-ONTOKENKEYSDEACTIVATED

4-Warning

On-Token RSA keypairs from token [chars] and associated IPSEC sessions being deactivated now

On-Token Router RSA keypairs and associated IPSEC sessions are being deactivated because the token containing them was removed

pki

"Re-insert the crypto token"

CRYPTO-6-TOKENLOGIN

6-Information

Cryptographic Token [chars] Login Successful

The cryptographic token has accepted the PIN offered by the router

-

"Informational message only. No action required."

CRYPTO-6-TOKENADMINLOGIN

6-Information

Cryptographic Token [chars] ADMIN Login Successful

The cryptographic token has accepted the administrator PIN offered by the router

-

"Informational message only. No action required."

CRYPTO-6-TOKENLOGOUT

6-Information

Cryptographic Token [chars] Logout Successful

The router has logged out from the cryptographic token

-

"Informational message only. No action required."

CRYPTO-6-TOKENCHANGEPIN

6-Information

Cryptographic Token [chars] PIN change Successful

The cryptographic token has accepted the new PIN offered by the router

-

"Informational message only. No action required."

CRYPTO-6-TOKENADMINCHANGEPIN

6-Information

Cryptographic Token [chars] ADMIN PIN change Successful

The cryptographic token has accepted the new administrator PIN offered by the router

-

"Informational message only. No action required."

CRYPTO-6-TOKENSTOREKEY

6-Information

Key [chars] stored on Cryptographic Token [chars] Successfully

A new keypair has been written out to the cryptographic token

-

"Informational message only. No action required."

CRYPTO-3-TOKENSTOREKEYFAILED

3-Error

Key [chars] store on Cryptographic Token [chars] Failed

An error occurred attempting to write a new keypair out to the cryptographic token

pki

"Try logging in to the token. If the error persists " "try logging in as admin"

CRYPTO-3-TOKENLOGINFAILED

3-Error

Cryptographic Token [chars] Login FAILED

The cryptographic token has rejected the PIN offered by the router

pki

"Issue 'crypto pki token user-pin' command to enter correct PIN"

CRYPTO-3-TOKENADMINLOGINFAILED

3-Error

Cryptographic Token [chars] ADMIN Login FAILED

The cryptographic token has rejected the administrator PIN offered by the router

pki

"Issue 'crypto pki token admin-pin' command to enter correct PIN"

CRYPTO-3-TOKENCHANGEPINFAILED

3-Error

Cryptographic Token [chars] Change PIN FAILED

The cryptographic token has rejected the new PIN offered by the router

pki

"Be sure you are logged in to the token as admin. Try a longer PIN."

CRYPTO-3-TOKENLOCKEDOUT

3-Error

Cryptographic Token [chars] PIN Locked due to too many unsuccessful login attempts

The cryptographic token has disabled the user PIN due to too many login failures

pki

"Issue 'crypto pki token admin-pin' command to enter correct ADMINISTRATOR PIN"

CRYPTO-3-TOKENADMINLOCKEDOUT

3-Error

Cryptographic Token [chars] Administrator PIN Locked due to too many unsuccessful login attempts

The cryptographic token has disabled the Admin PIN due to too many login failures

pki

"If the user PIN is also locked out it will be necessary to reinitialize the card." "The data on the card will be lost"

CRYPTO-3-TOKENAPIFAILURE

3-Error

Cryptographic Token [chars] API FAILED error = [dec]

The cryptographic token returned an unexpected error

pki

LOG_STD_ACTION

CRYPTO-3-NOSOCKET

3-Error

Unable to open [chars]

Call Admission Control is configured globally or at the IKE level on this device. Consequently an IKE SA request was denied do to the reason described in the error message.

ipsec

"Decrease the number of concurrent connections or " "inspect the crypto engine."

CRYPTO-3-MTREE_CMD_BLOCK

3-Error

Mtree command [dec] was blocked from the the mtree process queue.

An attempt was made to enqueue a command to the crypto mtree manager process even though IPsec is currently operating in HAPX mode.

ipsec

LOG_STD_ACTION

CRYPTO-3-IPSECV6_UNSUPPORTED

3-Error

IPv6 IPsec is not supported by the current available crypto hardware.

An attempt was made to configure a feature which will use IPv6 IPsec. IPv6 IPsec cannot be supported by the current encryption hardware. The configuration change was made but will not be functional until the encryption hardware configuration is changed.

ipsec

"Please remove the unsupported feature config " "or switch to a capable crypto engine."

CRYPTO-5-IKMP_AG_MODE_DISABLED

5-Notice

Unable to initiate or respond to Aggressive Mode while disabled

The router is configured not to accept or respond to ISAKMP aggressive mode with any peer

ipsec-isakmp

"If you did not intend to disable aggressive-mode" " then remove the command"

CRYPTO-3-IKMP_QUERY_KEY

3-Error

Querying key pair failed.

Querying public key/private key using subject name failed

-

"Check the subject name in the certificate."

CRYPTO-6-EZVPN_CONNECTION_UP

6-Information

[chars]

Ezvpn connection is up for the client mentioned. Both IPsec and IKE security Associations are up now.

-

""

CRYPTO-6-EZVPN_CONNECTION_DOWN

6-Information

[chars]

Ezvpn connection is being closed. The IPsec and IKE security associations will also be brought down along with it.

-

""

CRYPTO-3-EZVPN_VINTERFACE_CREATE_ERR

3-Error

EZVPN[chars]: Virtual-access interface creation failed

The virtual-interface feature will not work without a virtual-access interface. The EzVPN configuration is unusable. You can choose to remove virtual-interface configuration from ezvpn as a workaround

ipsec-ezvpn

"If this message occurs contact your technical " "support representative."

CRYPTO-6-VPN_TUNNEL_STATUS

6-Information

[chars]

VPN tunnel status.

-

""

CRYPTO-4-EZVPN_SA_LIMIT

4-Warning

[chars]

The limit for maximum no of ezvpn tunnels that can be setup on the platform has reached. Active SAs shall not be terminated but no additional SAs can be established until the number of existing SAs decreases.

-

""

CRYPTO-4-EZVPN_FAILED_TO_CONNECT

4-Warning

[chars]

Ezvpn session failed to come up ezvpn is stuck in a state waiting for an event posting a reset message to recover.

-

""

CRYPTO-5-GM_REGSTER

5-Notice

Start registration to KS [chars] for group [chars] using address [chars] fvrf [chars] ivrf [chars]

Start registration for one group

ipsec-mcast

LOG_STD_ACTION

CRYPTO-4-GM_LOCAL_ADDRESS

4-Warning

Failed to determine local ip address for group [chars] on interface [chars]

Failed to determine local address for GDOI crypto map

ipsec-mcast

LOG_STD_ACTION

CRYPTO-4-GM_ZERO_ADDRESS

4-Warning

No ip address found for group [chars] on source interface [chars]

Souce IP address for GDOI crypto map is zero

ipsec-mcast

LOG_STD_ACTION

CRYPTO-4-IKMP_HASH_SIZE_EXCEEDED

4-Warning

IKE hash size exceeded with peer at [inet].

A hash operation required by the IKE protocol exceeded an internal limit. The IKE SA negotiation was rejected. That can happen if an inordinately large number of IKE policies were being proposed by the initiator

-

"Reduce the number of configured IKE policies."

CRYPTO-5-GM_CONN_NEXT_SER

5-Notice

GM is connecting to next key server from the list

Connect to next key server

ipsec-mcast

LOG_STD_ACTION

CRYPTO-4-GM_REGSTER_IF_DOWN

4-Warning

Can't start GDOI registeration as interface [chars] is down

Interface is found down before registration

ipsec-mcast

LOG_STD_ACTION

CRYPTO-4-GM_ISAKMP_OFF

4-Warning

Can't start GDOI registration as ISAKMP disabled

Crypto ISAKMP is not enabled

ipsec-mcast

"Enable crypto ISAKMP"

CRYPTO-4-IKE_DEFAULT_POLICY_ACCEPTED

4-Warning

IKE default policy was matched and is being used.

The default policy is being used because the local configured policies did not match with the peer's policies.

ipsec-isakmp

"To avoid using the default policy " "reconfigure the local policy to match " "with peer's policy"

CRYPTO-6-IPSEC_USING_DEFAULT

6-Information

IPSec is using default transforms

No IPSec transform-set defined and default policy is enabled. Therefore default policies are being proposed to the peer

ipsec-core

"To avoid using IPSec default policy" "reconfigure a transform set to be used for " "this crypto session"

CRYPTO-3-GM_FAILCLOSE_UNSUPPORTED

3-Error

GETVPN failclose is not supported by the current available crypto hardware.

An attempt was made to configure the GETVPN failclose feature which cannot be supported by the current encryption hardware.

ipsec-mcast

"Please remove the unsupported feature config " "or switch to a capable crypto engine."

CRYPTO-3-PAL_INTERNAL_ERROR

3-Error

Internal error: [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_REQUEST_STATE

3-Error

Internal error: illegal request state [dec]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_BAD_TRANSITION

3-Error

Internal error: state [chars] has unrecognized transition [dec]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_BAD_MESSAGE

3-Error

Internal error: unrecognized message [dec]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_LOOP

3-Error

Internal error: [[chars]]: state loop detected: state = [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_NO_NEXT_STATE

3-Error

Internal error: undefined next state [dec]: previous state = [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_STATE_ALREADY_DEFINED

3-Error

Internal error: State [dec] already defined: old_state = [chars] new_state = [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_STATE_OVERFLOW

3-Error

Internal error: Table overflow new_state = [dec] [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_TRANSITION_OVERFLOW

3-Error

Internal error: Transition table overflow transition = [dec] state = [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_CANNOT_ALWAYS

3-Error

Internal error: Cannot do ALWAYS transition for state [chars]: transition already defined

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_ALREADY_ALWAYS

3-Error

Internal error: Cannot do transition for state [chars]: ALWAYS state already defined

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_INTERNAL_ERROR_TRANSITION_ALREADY

3-Error

Internal error: Transition [dec] already defined: state = [chars]

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_REQUEST_PENDING_ACTION

3-Error

Internal error: state [chars] has pending actions

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-PAL_REQUEST_OUTSIDE_ACTION

3-Error

Internal error: [chars] called from outside action routine

IPSec detected a serious internal error

ipsec-core

"None"

CRYPTO-3-INVALID_KMI_REQUEST

3-Error

Invalid KMI error: kmi_client: [dec] in processing [chars]

IPSec detected an invalid KMI

ipsec-core

"None"

CRYPTO-4-ADV_IPSERVICES_LIC_NOT_ENABLED

4-Warning

advipservices license is required to enable IPSec IPv6 feature. Please install the license and retry.\n

IPSec IPv6 subsystem is bundled with advipservices license. So check if this license is enabled to include IPSec IPv6 subsystem.

ipsec-core

"Enable ADV_IPSERVICES license."

CRYPTO-3-IPSEC_PAL_FATAL_ERROR

3-Error

IPsec PAL Fatal Error: [chars]

IPSec SM detected inconsistence and hence crashing the system

ipsec-core

"None"

DMVPN-3-NHRP_ERROR

3-Error

[chars]: [chars] failed for [chars] [chars] [dec] for Tunnel: [chars] NBMA: [chars] on Tunnel: [chars] NBMA: [chars]

Unable to send/receive packets.

nhrp

LOG_STD_ACTION

DMVPN-3-NHRP_REGISTRATION_ERROR

3-Error

[chars]: [chars] [chars] Error indication for [chars] - [chars][dec] Src Tunnel: [chars] NBMA: [chars] Dest Tunnel: [chars] NBMA: [chars]

NHRP Registration send/receive Error Indication packets.

nhrp

LOG_STD_ACTION

DMVPN-3-NHRP_RESOLUTION_ERROR

3-Error

[chars]: [chars] [chars] Error indication for [chars] - [chars][dec] Src Tunnel: [chars] NBMA: [chars] Dest Tunnel: [chars] NBMA: [chars]

NHRP Resolution send/receive Error Indication packets.

nhrp

LOG_STD_ACTION

DMVPN-4-NHRP_QUOTA

4-Warning

[chars]: Max-send Quota of [dec]pkts/[dec]sec exceeded on Tunnel: [chars] NBMA: [chars]

nhrp quota exceeded

nhrp

LOG_STD_ACTION

DMVPN-3-DMVPN_NHRP_ERROR

3-Error

[chars]: [chars] [chars] Reason: [chars] [dec] on Tunnel: [chars] NBMA: [chars]

NHRP Error messages

nhrp

LOG_STD_ACTION

DMVPN-3-DMVPN_NHRP_MULTICAST_ERR

3-Error

[chars]: [chars] on Tunnel: [chars] NBMA: [chars]

NHRP Multicast Replication Error messages

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NHS_UP

5-Notice

[chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars]

Next Hop Client changed the state.

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NHS_DOWN

5-Notice

[chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars]

Next Hop Client changed the state.

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NHC_UP

5-Notice

[chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars]

Next Hop Client changed the state.

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NHC_DOWN

5-Notice

[chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars]

Next Hop Client changed the state.

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NHP_UP

5-Notice

[chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars]

Next Hop Peer changed the state.

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NHP_DOWN

5-Notice

[chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars]

Next Hop Peer changed the state.

nhrp

LOG_STD_ACTION

DMVPN-7-NHRP_EVENT

7-Debug

[chars]: [chars] [chars] [chars] [chars] [chars]

A Registration/Resolution Request/Reply Received/Sent

nhrp

LOG_STD_ACTION

DMVPN-5-CRYPTO_SS

5-Notice

[chars]: local address : [chars] remote address : [chars] socket is [chars]

DMVPN Crypto UP/DOWN Syslog Event

nhrp

LOG_STD_ACTION

DMVPN-6-NHRP_RES

6-Information

[chars]: Host with Tunnel: [chars] NBMA: [chars] [chars] Tunnel: [chars] NBMA: [chars]

A NHRP Resolution Request has been received

nhrp

LOG_STD_ACTION

DMVPN-6-NHRP_RESOLUTION_REPLY

6-Information

[chars]: Host with Tunnel: [chars] NBMA: [chars] [chars] Tunnel: [chars] NBMA: [chars]

A NHRP Resolution Reply has been received

nhrp

LOG_STD_ACTION

DMVPN-6-NHRP_RES_TIMEOUT

6-Information

[chars]: [chars] for Address : [chars] is Timed-out

A NHRP Resolution Request has timed-out

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_RES_REPLY

5-Notice

[chars]: [chars] [chars] sent via Tunnel: [chars] NBMA: [chars] to Tunnel: [chars] NBMA: [chars]

A NHRP Resolution Reply sent via the NHS Path

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_RES_REPLY_IGNORE

5-Notice

[chars]: resolution reply received on [chars] for dst : [chars] is dropped crypto session failed to come up

A NHRP Resolution Reply received through Hub which is dropped - crypto session failed to come up

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_NETID_UNCONFIGURED

5-Notice

[chars]: NETID : [dec] [chars] Tunnel: [chars] NBMA: [chars]

NETID Unconfigured

nhrp

LOG_STD_ACTION

DMVPN-5-NHRP_ROUTING

5-Notice

Peer with Tunnel: [chars] NBMA: [chars] on [chars] [chars] with Reason :[chars] .

A short cut switching entry has been created

nhrp

LOG_STD_ACTION

NHRPSNMP-3-TREEINVALID

3-Error

Setting tree to Invalid State @ - [dec]

NHRP SNMP agent tree is not behaving as excepted.

nhrp

LOG_STD_ACTION

NHRPSNMP-5-TREERECOVERD

5-Notice

Tree recovered fromInvalid State @ - [dec]

NHRP SNMP agent tree is not behaving as excepted.

nhrp

LOG_STD_ACTION

NHRP-3-PAKREPLY

3-Error

Receive [chars] packet with error - [chars][dec]

An NHS rejects or fails to serve our request packet.

nhrp

LOG_STD_ACTION

NHRP-3-PAKERROR

3-Error

Received [chars] from [chars] code: [chars][dec] trigger src: [chars]

Received an error notification packet indicating that the last packet the system sent was bad or not understood by the recipient.

nhrp

LOG_STD_ACTION

NHRP-3-CACHE_FAILURE

3-Error

Failed to cache [chars] packet - [chars][dec]

Caching of information from NHRP packet failed.

nhrp

LOG_STD_ACTION

NHRP-3-TRACE_ILLEGAL_EVENT

3-Error

[chars]

nhrp trace event type is invalid

nhrp

LOG_STD_ACTION

NHRP-3-TIMERLOOP

3-Error

Timer process looping [dec]/[dec]/[dec]/[dec]/[dec]/[dec].

-

-

-

NHRP-4-QUOTA

4-Warning

Max-send quota of [dec]pkts/[dec]Sec. exceeded on [chars].

Quota for sending NHRP packets on the interface exceeds the limit.

nhrp

LOG_STD_ACTION

NHRP-5-NHOP_UNREACHABLE

5-Notice

Nexthop address [chars] for [chars]/%lu is not routable

The nexthop address for a shortcut is not routable

nhrp

"If this is not a transient routing change check the" " routing design/config to make sure that the nexthop" " corresponding to the shortcut has a covering route!"

NHRP-3-QOS_POLICY_APPLY_FAILED

3-Error

Failed to apply QoS policy [chars] mapped to NHRP group [chars] on interface [chars] to tunnel [chars] due to [chars]

The application of QoS policy to tunnel failed. The failure could be due to internal error or policy installation failure. Policy installation can fail if the policy configuration is not supported for a tunnel.

nhrp

LOG_STD_ACTION

NHRP-4-MAX_RECURSIVE_ROUTE_DEPTH_REACHED

4-Warning

Route lookup failed reached maximum recursive depth [dec]

The ECMP recursive look up reached the maximum depth

nhrp

LOG_STD_ACTION

NHRP-5-NO_ROUTE

5-Notice

Not installing NHO for [chars]/[dec] due to the presence of an authoritatively learnt nexthop [chars] on [chars]

NHO was not installed because of an already existing route entry

nhrp

LOG_STD_ACTION

NHRP-4-NHRP_ROUTER_AF_IMPORT

4-Warning

BGP AS specified in router nhrp import config is not running or not configured yet. Configuring router bgp with AS number [dec]

BGP AS number specified in import command of NHRP is not yet configured

nhrp

LOG_STD_ACTION

CLB-4-CLB_VERSION_MISMATCH

4-Warning

[chars]

Version mismatch for Cluster load-balancer feature. Master could ignore some load attributes while calculating load of a Slave.

-

"Upgrade to an IOS image with " "latest version of Cluster " "load-balancer feature"

CLB-6-CLB_SLAVE_CONNECTED

6-Information

[chars]

Recevied new Slave connection. Master now receives update from this Slave.

-

""

CLB-4-CLB_SLAVE_DEAD

4-Warning

[chars]

Slave connection is dead and is being closed. Master no longer receives updates from this Slave.

-

""

FLEXVPN-6-FLEXVPN_CONNECTION_UP

6-Information

[chars]

FlexVPN connection is up for the client mentioned. Both IPsec and IKE security Associations are up now.

-

""

FLEXVPN-6-FLEXVPN_CONNECTION_DOWN

6-Information

[chars]

FlexVPN connection is being closed. The IPsec and IKE security associations will also be brought down along with it.

-

""

FLEXVPN-4-FLEXVPN_FAILED_TO_CONNECT

4-Warning

[chars]

FlexVPN session failed to come up FlexVPN is stuck in a state waiting for an event posting a disconnect message to recover.

-

""

IPSECV6-4-RECVD_PKT_V6_INV_PROT

4-Warning

decapsulate: packet missing [chars] destadr=%P actual prot=[dec]

Rec'd IPSEC packet missing an expected AH or ESP header The peer is sending packets that don't match the negotiated security policy. Some might consider this a hostile event.

-

"Contact the peer's administrator."

IPSECV6-4-PKT_PROTOCOL_MISMATCH

4-Warning

IP protocol in packet mismatched with tunnel mode packet from [chars] to [chars] dropped by [chars]

We tried to send an IPv4 packet into an IPSec-IPv6 tunnel or an IPv6 packet into an IPSec-IPv4 tunnel. The tunnel cannot handle this type of packet and so the packet is dropped.

-

"Modify the tunnel configuration either by removing the" " incorrect IP address type from the tunnel interface or by" " changing the tunnel mode to match the IP address type."

IPSECV6-4-RECVD_PKT_V6_INV_SPI

4-Warning

decaps: rec'd IPSEC packet has invalid spi for\n \tdestaddr=%P prot=[dec] spi=0x[hec][dec] srcaddr=%P

-

-

-

IPSECV6-4-RECVD_PKT_V6_MSG_LEN_ERR

4-Warning

decapsulate: packet has bad [chars] length destadr=%P prot=[dec] len=[dec]

Rec'd IPSEC packet is malformed: possibly encapsulation error? The peer is sending malformed packets. It may be due to a decryption error. Some might consider this a hostile event.

-

"Contact the peer's administrator."

IPSECV6-4-RECVD_PKT_NOT_IPSECV6

4-Warning

Rec'd packet not an IPSEC packet.\n \tip dest_addr= %P src_addr= %P prot= [dec]

-

-

-

TUNSS-6-PROTECTION_BAD_TUN_MODE

6-Information

Tunnel mode [chars] not supported by tunnel protection. Protection removed.

The chosen tunnel mode is not supported by tunnel protection interfaces so protection has been turned off and removed.

tunnel

"Unless protection is desired on this interface no " "action is required. If protection is desired a " "crypto-map must be used instead."

TUNSS-3-PROTECTION_PROCESS_FAIL

3-Error

Failed to create tunnel security process

We failed to start a processes necessary to do tunnel protection.

tunnel

LOG_STD_ACTION

TUNSS-3-TUN_API_ARGS

3-Error

unexpected arguments: [chars] [chars]

This API should be used only for a tunnel interface.

tunnel

LOG_STD_ACTION

GDOI-1-GDOI_ACL_NUM

1-Alert

The ACL has too many entries.\n GDOI will honor only the first 100 ACL entries specified.

The ACL has too many entries. GDOI will honor only the first 100 ACL entries specified.

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-GDOI_ACL_RANGE

3-Error

The ACL [chars] contains port range which is NOT supported. WARNING: No TEK policy will be created.

GDOI does not support port range in the ACL policy.

ipsec-getvpn

LOG_STD_ACTION

GDOI-1-GDOI_ACE_DENY

1-Alert

A Group Member ACL policy containing deny was attempted. This is not supported.

A Group Member ACL policy containing deny was attempted. This is not supported.

ipsec-getvpn

LOG_STD_ACTION

GDOI-1-UNREGISTERED_INTERFACE

1-Alert

Group [chars] received registration from unregistered interface.

Receiving registration from unregistered interface. Stop processing it.

ipsec-getvpn

LOG_STD_ACTION

GDOI-1-UNAUTHORIZED_IDENTITY

1-Alert

Group [chars] received registration from unauthorized identity: [chars]

The registration request was dropped because the requesting device was not authorized to join the group.

ipsec-getvpn

LOG_STD_ACTION

GDOI-1-UNAUTHORIZED_IPADDR

1-Alert

Group [chars] received registration from unauthorized ip address: [chars]

The registration request was dropped because the requesting device was not authorized to join the group.

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-GM_RE_REGISTER

4-Warning

The IPSec SA created for group [chars] may have expired/been cleared or didn't go through. Re-register to KS.

The IPSec SA created for one group may have expired/been cleared or didn't go through need to re-register to KS.

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-GM_PFS_RE_REGISTER

4-Warning

Start PFS triggered re-registration to KS [chars] for group [chars] using address [chars] fvrf [chars] ivrf [chars]

Received PFS Rekey Hence re-registring to download new policy.

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_REGS_COMPL

5-Notice

Registration to KS [chars] complete for group [chars] using address [chars] fvrf [chars] ivrf [chars]

Complete registration

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_FAILED_TO_INSTALL_POLICIES

5-Notice

FAILED: Installation of Reg/Rekey policies from KS [chars] for group [chars] & gm identity [chars]

Failed Policy installation

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_INSTALL_POLICIES_SUCCESS

5-Notice

SUCCESS: Installation of Reg/Rekey policies from KS [chars] for group [chars] & gm identity [chars] fvrf [chars] ivrf [chars]

Policy Installation Success

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_RECV_REKEY

5-Notice

Received Rekey for group [chars] from [chars] to [chars] with seq # [dec] spi 0x[hec][hec][hec][hec]

Received Rekey

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-KS_SEND_MCAST_REKEY

5-Notice

Sending Multicast Rekey [chars]for group [chars] from address [chars] to [chars] with seq # [dec] spi: 0x[hec][hec][hec][hec]

Sending Multicast Rekey

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-KS_SEND_UNICAST_REKEY

5-Notice

Sending Unicast Rekey [chars]for group [chars] from address [chars] with seq # [dec] spi: 0x[hec][hec][hec][hec]

Sending Unicast Rekey

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-KS_BAD_ID

3-Error

Registration: [chars] config mismatch between KS and the GM [inet] in the group [chars].

During GDOI registration protocol a configuration mismatch between local key server and group member.

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-3-GDOI_REKEY_FAILURE

3-Error

Processing of REKEY payloads failed on GM [chars] in the group [chars] with peer at [chars]

During GDOI rekey the payload parsing failed on this GM from the Key Server.

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-3-GDOI_REKEY_SEQ_FAILURE

3-Error

Failed to process rekey seq # [dec] in seq payload for group [chars] last seq # [dec]

During GDOI rekey the seq payload parsing failed on this GM from the Key Server.

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-4-KS_GM_REJECTS_SA_PAYLOAD

4-Warning

Registration: GM [inet] rejected a policy in the SA proposal sent by KS in the group [chars].

During GDOI registration protocol a proposal sent by the key server was refused by the group member.

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-4-GM_REJECTING_SA_PAYLOAD

4-Warning

Registration: Policy in SA payload sent by KS [inet] rejected by GM in the group [chars] reason [chars].

During GDOI registration protocol a proposal sent by the key server was refused by the local group member.

ipsec-getvpn

"Contact the Key server's administrator."

GDOI-4-KS_HASH_FAIL

4-Warning

Registration: BadNo Hash in Message sent by the GM [inet]

During GDOI registration protocol a message sent by the Group member has bad or no hash .

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-4-GM_HASH_FAIL

4-Warning

Registration: BadNo hash in message sent by the KS [inet]

During GDOI registration protocol a message sent by the Key server has bad or no hash .

ipsec-getvpn

"Contact the Key Server's administrator."

GDOI-3-KS_UNAUTHORIZED

3-Error

Registration: Unauthorized [inet] tried to join the group [chars].

During GDOI registration protocol an unauthorized member tried to join a group Some might consider this a hostile event.

ipsec-getvpn

"Contact the Key Server's administrator."

GDOI-3-KS_GM_REVOKED

3-Error

Re-Key: GM [inet] revoked by KS in the group [chars].

During Re-key protocol an unauthorized member tried to join a group. Some might consider this a hostile event.

ipsec-getvpn

"Contact the Key Server's administrator."

GDOI-5-KS_GROUP_ADD

5-Notice

Config: KS [inet] added to the Group [chars].

A Config command has been executed to add a Key Server in a group

ipsec-getvpn

"Informational message."

GDOI-5-KS_GROUP_DELETE

5-Notice

Config: KS [inet] removed from the Group [chars].

A Config command has been executed to remove a Key Server from a group

ipsec-getvpn

"Informational message."

GDOI-6-KS_FIRST_GM

6-Information

Re-key: First GM [inet] seen by KS in the group [chars].

Local key server has received the first group member joining the group

ipsec-getvpn

"Informational message."

GDOI-6-KS_LAST_GM

6-Information

Re-key: Last GM [inet] left the group [chars].

Last group member has left the group on the local key server

ipsec-getvpn

"Informational message."

GDOI-5-GM_CM_ATTACH

5-Notice

Crypto map attached for GM in group [chars].

A crypto map has been attached for the local group member.

ipsec-getvpn

"Informational message."

GDOI-5-GM_CM_DETACH

5-Notice

Crypto map detached for GM in group [chars].

A crypto map has been detached for the local group member.

ipsec-getvpn

"Informational message."

GDOI-5-GM_UNREGISTER

5-Notice

GM left the group [chars].

A Group member has left the group.

ipsec-getvpn

"Informational message."

GDOI-4-GM_RECV_POLICY_REPLACE_NOW

4-Warning

GM received policy replace now rekey from KS in group [chars].

A messages sent by the KS to immediately replace SAs policies on the GM has been received.

ipsec-getvpn

"Informational message."

GDOI-4-GM_RECV_DELETE_IMMEDIATE

4-Warning

GM receive REMOVAL-NOW in group [chars] to cleanup downloaded policy now. Re-registration will start in a randomly chosen period of [dec] sec

A messages sent by the KS to delete the GM has been received.

ipsec-getvpn

"Informational message."

GDOI-4-GM_RECV_RE_AUTH

4-Warning

GM received Re-auth-msg from KS in group [chars]. re-registration will start before SA expiry

A message sent by the KS to have a GM re-auth has been received.

ipsec-getvpn

"Informational message."

GDOI-4-GM_RECV_DELETE

4-Warning

GM received delete-msg from KS in group [chars]. TEKs lifetime are reduced and re-registration will start before SA expiry

A messages sent by the KS to delete the GM has been received.

ipsec-getvpn

"Informational message."

GDOI-5-GM_CLEAR_REGISTER

5-Notice

Config: GM cleared gdoi configuration for the group [chars].

clear crypto gdoi command has been executed by the local GM

ipsec-getvpn

"Informational message."

GDOI-5-KS_CLEAR_REGISTER

5-Notice

Config: KS cleared gdoi configuration for the group [chars].

clear crypto gdoi command has been executed by the local KS

ipsec-getvpn

"Informational message."

GDOI-3-COOP_KS_UNREACH

3-Error

Cooperative KS [chars] Unreachable in group [chars]. IKE SA Status = [chars]

The reachability between the configugred cooperative key servers is lost. Some might consider this a hostile event.

ipsec-getvpn

"Contach the Administrators of the configured key servers."

GDOI-5-COOP_KS_REACH

5-Notice

Reachability restored with Cooperative KS [chars] in group [chars].

The reachability between the configugred cooperative key servers is restored.

ipsec-getvpn

"Informational message"

GDOI-5-COOP_KS_ADD

5-Notice

[chars] added as COOP Key Server in group [chars].

A key server has been added to the list of cooperative key servers in a group

ipsec-getvpn

"Informational message"

GDOI-5-COOP_KS_REMOVE

5-Notice

[chars] removed as COOP Key Server in group [chars].

A key server has been removed from the list of cooperative key servers in a group

ipsec-getvpn

"Informational message"

GDOI-4-COOP_KS_UNAUTH

4-Warning

Contact from unauthorized KS [chars] in group [chars] at local address [chars] Possible MISCONFIG of peer/local address

-

-

-

GDOI-5-COOP_KS_ELECTION

5-Notice

KS entering election mode in group [chars] Previous Primary = [chars]

The local Key server has entered the election process in a group

ipsec-getvpn

"Informational message"

GDOI-5-COOP_KS_TRANS_TO_PRI

5-Notice

KS [chars] in group [chars] transitioned to Primary Previous Primary = [chars]

The local Key server transitioned to a primary role from being a secondary server in a group

ipsec-getvpn

"Informational message"

GDOI-5-COOP_KS_ADMN_USRP_PRI

5-Notice

Primary role Usurped by KS [chars] in group [chars].

A network adminstrator has made the local KS as primary by means of a CLI command. Currently Unimplemented.

ipsec-getvpn

"Informational message"

GDOI-5-GM_REKEY_TRANS_2_MULTI

5-Notice

Group [chars] transitioned to multicast rekey.

GM has transitioned from using unicast rekey mechanism to multicast mechanism

ipsec-getvpn

"Informational message"

GDOI-5-KS_REKEY_TRANS_2_MULTI

5-Notice

Group [chars] transitioned to multicast rekey.

Group has transitioned from using unicast rekey mechanism to multicast mechanism

ipsec-getvpn

"Informational message"

GDOI-5-GM_REKEY_TRANS_2_UNI

5-Notice

Group [chars] transitioned to Unicast Rekey.

GM has transitioned from using multicast rekey mechanism to unicast mechanism

ipsec-getvpn

"Informational message"

GDOI-5-KS_REKEY_SYNCUP_2_REPLACE

5-Notice

Group [chars] transitioned to primary but no policy generated yet continuing with POLICY REPLACE rekey

KS Group has transitioned to new Primary but no policy generated yet to recover from this situation continuing with POLICY REPLACE rekey

ipsec-getvpn

"Informational message"

GDOI-5-KS_REKEY_TRANS_2_UNI

5-Notice

Group [chars] transitioned to Unicast Rekey.

Group has transitioned from using multicast rekey mechanism to unicast mechanism

ipsec-getvpn

"Informational message"

GDOI-4-GM_REKEY_NOT_RECD

4-Warning

GM did not receive rekey from KS [inet] in group [chars].

GM has not received a rekey message from a key server in a group Currently Unimplemented.

ipsec-getvpn

"Informational message"

GDOI-5-KS_NACK_GM_EJECT

5-Notice

KS ejected GM [inet] in group [chars].

Key server has reached a condition of not receiving an ACK from GM and has been ejected

ipsec-getvpn

"Informational message"

GDOI-3-KS_BLACKHOLE_ACK

3-Error

KS blackholing GM [inet] in group [chars].

Key server has reached a condition of blackholing messages from GM Some might consider this a hostile event.

ipsec-getvpn

-

GDOI-4-KS_UNSOL_ACK

4-Warning

KS received unsolicited ACK from GM [inet] in group [chars].

Key server has received an unsolicited ACK from a past GM or is under a DOS attack. Some might consider this a hostile event.

ipsec-getvpn

-

GDOI-5-KS_REGS_COMPL

5-Notice

KS completed successful registration in group [chars] with GM [inet].

Key server has successfully completed a registration in a group

ipsec-getvpn

-

GDOI-5-GM_ENABLE_GDOI_CM

5-Notice

GM has enabled ACL on GDOI crypto map in group [chars].

Group member has enabled ACL on a GDOI Crypto map in a group with a key server

ipsec-getvpn

-

GDOI-5-GM_ACL_MERGE

5-Notice

ACL betweem KS and GM in group [chars] merged.

The ACL differences between GM and KS are resolved and a merge took place

ipsec-getvpn

-

GDOI-5-GM_SA_INGRESS

5-Notice

Receive only ACL received from KS [inet] in group [chars].

Received only acl has been received by GM from a KS in a group

ipsec-getvpn

-

GDOI-5-KS_CONV_SAS_DUPLEX

5-Notice

IPSec SAs converted to Duplex in group [chars].

IPSec SAs have been converted to bidirectional mode in a group

ipsec-getvpn

-

GDOI-5-KS_CONV_SAS_INGRESS

5-Notice

IPSec SAs converted to Ingress in group [chars].

IPSec SAs have been converted to receive only mode in a group

ipsec-getvpn

-

GDOI-5-GM_CONV_SA_DUPLEX

5-Notice

IPSec SAs converted to Duplex in group [chars] on the GM.

IPSec SAs have been converted to bidirectional mode in a group on a GM

ipsec-getvpn

-

GDOI-5-GM_CONV_SA_DUPLEX_LOCAL

5-Notice

IPSec SAs converted to Duplex in group [chars] on a GM by a local event.

IPSec SAs have been converted to bidirectional mode in a group on a GM by a CLI command

ipsec-getvpn

-

GDOI-5-LKH_ENABLE

5-Notice

LKH enabled in group [chars].

LKH has been enabled in a group

ipsec-getvpn

-

GDOI-5-LKH_DISABLE

5-Notice

LKH disabled in group [chars].

LKH has been disabled in a group

ipsec-getvpn

-

GDOI-4-LKH_GM_DELETE

4-Warning

GM [inet] deleted from LKH in group [chars].

A Group member has been deleted in a group from LKH

ipsec-getvpn

-

GDOI-4-TIMEBASED_REPLAY_FAILED

4-Warning

An anti replay check has failed in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = [dec] sec src_ip = [inet] dst_ip = [inet]

-

-

-

GDOI-3-PIP_PSEUDO_TIME_ERROR

3-Error

An Anti-Replay check has failed for PIP in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = %lld sec src_addr = [chars] dst_addr = [chars]

-

-

-

GDOI-3-P2P_KGS_INFRA_ERROR

3-Error

PIP session with [chars] failed because of KGS Infra failure. Reason = [chars]

A Group Member has encountered a KGS Infra failure.

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-TIMEBASED_REPLAY_FAILED_IPV6

4-Warning

An anti replay check has failed in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = [dec] sec src_ip = %P dst_ip = %P

-

-

-

GDOI-3-GM_FAILED_TO_INITIALISE

3-Error

GDOI GM Process has failed to initialise

GDOI Group Member process has failed to initialise on this Network Element

ipsec-getvpn

-

GDOI-3-PSEUDO_TIME_LARGE

3-Error

Pseudotime difference between KS [dec] sec and GM [dec] sec

A Group member has received pseudotime which has large difference as compared to own pseudotime

ipsec-getvpn

-

GDOI-3-PSEUDO_TIME_TOO_OLD

3-Error

Rekey received in group [chars] is too old and fail PST check: my_pst is [dec] sec peer_pst is [dec] sec allowable_skew is [dec] sec

A Group member has received pseudotime which has large difference as compared to own pseudotime

ipsec-getvpn

-

GDOI-3-GM_INCOMPLETE_CFG

3-Error

Registration: incomplete config for group [chars]

Registration can not be completed since the GDOI group configuration may be missing the group id server id or both

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-1-KS_NO_RSA_KEYS

1-Alert

RSA Key - [chars] : Not found Required for group [chars]

Rsa Keys were not found in Key Server and they are required for signing and verifying rekey messages

ipsec-getvpn

"Contact the Key Server's administrator and ask him to do create" " the RSA Key pair"

GDOI-4-RSA_KEYS_MODIFIED

4-Warning

WARNING: GMs for group [chars] will re-register due to signature verification failure

Rekeys will be dropped by GM as signature verification would fail due to modification of RSA Keys

ipsec-getvpn

"Informational message"

GDOI-3-KS_REKEY_AUTH_KEY_LENGTH_INSUFFICIENT

3-Error

Rejected [chars] change: using sig-hash algorithm [chars] requires an authentication key length of at least [dec] bits [dec] blocks in bytes

Using a sig-hash algorithm for rekeys requires that the RSA key modulus length for the rekey authentication be at least the length of the hash generated by the sig-hash algorithm plus some padding bytes. If the RSA key modulus length is not large enough the Key Server administrator needs to generate a new RSA key pair wit a sufficient length.

ipsec-getvpn

"Contact the Key Server's administrator to re-generate the RSA " "key pair with at least the modulus length given in the syslog."

GDOI-3-COOP_CONFIG_MISMATCH

3-Error

WARNING: Group [chars] [chars] configuration between Primary KS and Secondary KS are mismatched

The configuration between Primary KS and Secondary KS are mismatched

ipsec-getvpn

"Contact the Key Sever's administrator"

GDOI-3-GM_ACL_PERMIT

3-Error

GM doesn't support permit configured under local access-list. Traffic from [chars] to [chars] will be dropped.

GM can only support ACL for deny. Any traffic matching the permit entry will be dropped.

ipsec-getvpn

"Remove the permit entry from the ACL used by GDOI crypto map"

GDOI-3-GM_NO_IPSEC_FLOWS

3-Error

IPSec FLOW limit possibly reached

Hardware Limitation for IPSec Flow limit Reached. Cannot create any more IPSec SAs

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-3-GM_NO_CRYPTO_ENGINE

3-Error

No crypto engine is found due to lack of resource or unsupported feature requested

Failed to select a suitable crypto engine because requested packet path not available or requested feature not supported

ipsec-getvpn

"Check policy configured on KS"

GDOI-3-COOP_PACKET_DROPPED

3-Error

Announcement message dropped due to packet size [dec] bytes.

Hard limit set on the driver buffer size prevents sending packets of this size or bigger

ipsec-getvpn

"Informational message"

GDOI-3-UNEXPECTED_SIGKEY

3-Error

Unexpected Signature Key detected: freeing it

Unexpected Signature Key found: freeing the signature key

ipsec-getvpn

"Informational message"

GDOI-3-UNSUPPORTED_TEK_PROTO

3-Error

Unexpected TEK Protocol : [dec]

Unexpected TEK PROTOCOL

ipsec-getvpn

"Informational message"

GDOI-4-GM_DELETE

4-Warning

GM [chars] deleted from group [chars].

A group member has been deleted in a group from Key Server

ipsec-getvpn

"Informational message"

GDOI-5-KS_USING_DEFAULT_TRANSFORM

5-Notice

GETVPN is using default transforms for profile [chars]

Using default transformset

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_REKEY_CIPHER_HASH_CHECK_FAIL

5-Notice

Rekey cipher/hash [chars] used in Group [chars] is unacceptable

The key-server has chosen KEK rekey cipher/hash algorithms which are not acceptable by this group-member

-

"Contact the Key server's administrator."

GDOI-5-GM_REKEY_TRANSFORMSET_CHECK_FAIL

5-Notice

The transformset [chars] for data-protection in Group [chars] is

The key-server has chosen a TEK transformset which is not acceptable by this group-member

-

"Contact the Key server's administrator."

GDOI-3-COOP_ANN_SEQ_FAILURE

3-Error

COOP Ann msg seq check failed for group [chars] ann seq# [dec] sess seq# [dec]

COOP Ann msg seq check failed

ipsec-getvpn

"Contact Administrator"

GDOI-4-GDOI_ANN_TIMESTAMP_TOO_OLD

4-Warning

COOP_KS ANN from KS [chars] in group [chars] is too old and fail PST check:\n my_pst is %llu sec peer_pst is %llu sec allowable_skew is [dec] sec

The KS has received an ANN msg from a primary KS in which the timestamp is too old

ipsec-getvpn

-

GDOI-4-GDOI_ANN_TIMESTAMP_LARGE

4-Warning

COOP_KS ANN received from KS [chars] in group [chars] has PST bigger than myself. Adjust to new PST:\n my_old_pst is %llu sec peer_pst is %llu sec

-

ipsec-getvpn

-

GDOI-4-GDOI_ANN_TIMESTAMP_LARGE_NO_UPDATE

4-Warning

COOP_KS ANN received from KS [chars] in group [chars] has PST bigger than myself:\n my_pst is %llu sec peer_pst is %llu sec

-

ipsec-getvpn

-

GDOI-4-GDOI_ANN_INCONSISTENT_TBAR

4-Warning

COOP_KS ANN received from [chars] in group [chars] has inconsistent TBAR setting inconsistent than mine

The KS has received an ANN msg from a secondary KS in which the timestamp is too old

ipsec-getvpn

-

GDOI-5-COOP_KS_VALID_ANN_TIMER_EXPIRED

5-Notice

This sec-KS has NOT received an ANN with valid PST for an extended period in group [chars]. It will block new GMs registration temporarily until a valid ANN is received

No valid ANN message has been received in this secondary KS for a prolong period. Temporarily blocking new GM registrations until a valid ANN is received

ipsec-getvpn

"Informational message"

GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_ANN

5-Notice

This KS temporarily blocks GM with ip-addr [chars] from registering in group [chars] as it has not received an ANN with valid PST for prolonged period

No valid ANN message has been received in this secondary KS for a prolong period. Temporarily blocking new GM registrations until a valid ANN is received

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_ELECTION

5-Notice

This KS temporarily blocks GM with ip-addr [chars] from registering in group [chars] as the KS election is underway

The KS is in the process of electing a primary. Temporarily blocking new GM registrations until the election is complete

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_KSSID

5-Notice

This KS is blocking GM with ip-addr [chars] from registering in group [chars] as it has overlapping KS Sender Identifiers KSSID with

Another COOP-KS peer in the group has been configured with a KSSID value that is the same as one configured on this KS. GM registration is blocked as a result until the overlap is fixed.

ipsec-getvpn

"Check the configured KSSIDs for all COOP-KS peers by issuing "

GDOI-5-COOP_KS_RESUME_NEW_GM_REGISTER

5-Notice

This KS will now resume new GM registration functionality in group [chars]

This KS will now resume new GM registration functionality

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-SA_KEK_UPDATED

5-Notice

SA KEK was updated 0x%08X%08X%08X%08X

KEK was updated in the Registration/Rekey and a new KEK SA was created

ipsec-getvpn

"Informational message."

GDOI-5-SA_PIP_UPDATED

5-Notice

SA PIP was updated 0x[chars]

PIP was updated in Registration/Rekey and a new PIP SA was created

ipsec-getvpn

"Informational message."

GDOI-3-SA_KEK_INSATALL_FAILED

3-Error

Failed to install KEK SA

KEK SA instalation has failed

ipsec-getvpn

"Informational message."

GDOI-3-P2P_PEER_MIGRATE_FAILED

3-Error

Failed to install P2P rekey SA with peer [chars] in group [chars]

Installation of P2P Rekey SA with an existing peer has failed

ipsec-getvpn

"Check the status of all peers using the command " " 'show crypto gdoi gm p2p peers' and wait for PIP initiation between " "the failed peers. Traffic distruption may occur."

GDOI-5-SA_TEK_UPDATED

5-Notice

SA TEK was updated

TEK was updated in the Registration/Rekey and a new TEK IPSEC SA was created

ipsec-getvpn

"Informational message."

GDOI-5-GM_POLICY_CLEANUP

5-Notice

KS downloaded Policy Cleared and Fail Close policy installed for reg_gm [chars] in group [chars]

As the Fail close revert option is configured and KS is not reachable or registartion is failed we will remove the KS downloaded policy and apply the Fail close policy back on this GM

ipsec-getvpn

"Informational message."

GDOI-5-TEK_ATD_TIMER_STARTED

5-Notice

TEK ATD Timer started for [dec] seconds New TEK will be installed once ATD timer expires

TEK ATD timer started and new TEK will be installed after atd timer expiry

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-GM_MINOR_VERSION_MISMATCH

4-Warning

GM [inet] Minor Version mismatch. Use 'show crypto gdoi ks members' to see GM versions

GM has different minor version.

ipsec-getvpn

"show crypto gdoi ks members"

GDOI-3-GM_MAJOR_VERSION_MISMATCH

3-Error

GM [inet] registration rejected due to major version mismatch. GM must be using major version [dec] in order to be compatible with this KS

GM has a non-compatible major version.

ipsec-getvpn

"Check GDOI version compatibility on KS and GMs"

GDOI-4-KS_MINOR_VERSION_MISMATCH

4-Warning

COOP-KS Minor Version mistmatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec]

Coop KS has different minor version.

ipsec-getvpn

"show crypto gdoi ks coop"

GDOI-3-KS_MAJOR_VERSION_MISMATCH

3-Error

COOP-KS Major Version mismatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec]

COOP-KS has a non-compatible major version.

ipsec-getvpn

"Check GDOI version compatibility on KS"

GDOI-2-COOP_MINOR_VERSION_MISMATCH

2-Critical

COOP-KS Minor version mistmatch in group [chars]. My COOP version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec]. Upgrade [chars] [chars] to COOP version [dec].[dec].[dec] to prevent COOP outage.

Coop KS has different minor version.

ipsec-getvpn

"show crypto gdoi ks coop"

GDOI-3-COOP_MAJOR_VERSION_MISMATCH

3-Error

COOP-KS Major Version mismatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec]

COOP-KS has a non-compatible major version.

ipsec-getvpn

"Check COOP version compatibility on KS"

GDOI-3-COOP_LIMIT_REACHED

3-Error

Peer [chars] has reached COOP limit of maximum number of gms. COOP GM database sync fails. Upgrade to COOP version [dec].[dec].[dec] and above

COOP-KS has a non-compatible peer.

ipsec-getvpn

"Check COOP version compatibility on peer KS"

GDOI-5-POLICY_CHANGE

5-Notice

GDOI group [chars] policy has changed. Use 'crypto gdoi ks rekey' to send a rekey or the changes will be send in the next scheduled rekey

Reminder message that GDOI configuration has changed.

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-ESON_POLICY_CHANGE_RESTART1

5-Notice

ESON group [chars] policy has changed. Must use 'clear crypto gdoi ks members now' to restart the group

Reminder message that ESON configuration has changed.

eson-ckm

LOG_STD_ACTION

GDOI-5-ESON_POLICY_CHANGE_RESTART2

5-Notice

ESON group [chars] policy has changed. Must use 'crypto gdoi ks replace now' to restart the group

Reminder message that ESON configuration has changed.

eson-ckm

LOG_STD_ACTION

GDOI-5-GM_DELETE_EXPIRED_KEK

5-Notice

KEK expired for group [chars] and was deleted

Deleting Expired KEK

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_DELETE_EXPIRED_PIP

5-Notice

PIP with SPI 0x[chars] expired for group [chars] and was deleted

Deleting Expired PIP

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_DELETE_EXPIRED_P2P

5-Notice

P2P SA with epoch hash 0x[chars] expired for group [chars] and was deleted

Deleting Expired P2P

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-POLICY_CHANGE_TO_SUITEB

5-Notice

Group [chars] changed to Suite-B policy. Use 'crypto gdoi ks rekey' to generate the new Suite-B policy and cause all GMs to re-register to download SIDs or this will happen in the next scheduled rekey

Migrating from non-Suite-B to Suite-B policy requires that the user issues 'crypto gdoi ks rekey' like any other POLICY_CHANGE but this will cause a re-initialization rather than just a rekey.

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-KS_REINIT_GROUP

5-Notice

[chars] for group [chars] and will re-initialize the group.

KS has reached one of the following conditions indicated by the first part of the message requiring re-initialization of the group:\n

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-KS_REINIT_FINISH

5-Notice

Re-initialization of group [chars] completed.

A previously triggered re-initialization as signified by a \%GDOI-5-KS_REINIT_GROUP syslog has completed after the expiry of the old TEK.

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-KS_NO_SID_AVAILABLE

3-Error

GMs for group [chars] need SIDs but this KS has no KS SIDs configured or no more SIDs available.

This KS has a counter-mode transform configured requiring SIDs and either has no KSSIDs configured or has run out of SIDs. Registering GMs will not be able to register successfully until more KSSIDs are configured on this KS.

ipsec-getvpn

"Check the configured KSSIDs for this KS by issuing "

GDOI-3-COOP_KSSID_OVERLAP

3-Error

Overlapping KS Sender Identifiers KSSID {[chars]}

Another COOP-KS peer in the group has been configured with a KSSID value that is the same as one configured on this KS. GM registration is blocked as a result until the overlap is fixed.

ipsec-getvpn

"Check the configured KSSIDs for all COOP-KS peers by issuing "

GDOI-5-COOP_KSSID_OVERLAP_RESOLVED

5-Notice

Resolved overlapping KS Sender Identifiers KSSID

Another COOP-KS peer in the group had been configured with a KSSID value that was the same as one configured on this KS but has been resolved so that GM registration is allowed again.

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-GM_IV_EXHAUSTED

5-Notice

GM for group [chars] exhausted its IV space for interface [chars] and will re-register.

This GM is registering to an IPv6 group but erroneously receiving IPv4 policies in rekey

ipsec-getvpn

"Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. "

GDOI-4-NEWER_GM_VERSION_REGISTER

4-Warning

WARNING: GM [chars] registers to group [chars] with newer GDOI version than KS. Please check'show crypto gdoi ks members' and 'show crypto gdoi feature' to ensure all GMs can support the GETVPN features enabled.

-

ipsec-getvpn

"Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. "

GDOI-4-REJECT_GM_VERSION_REGISTER

4-Warning

Reject registration of GM [inet] ver 0x[hec] in group [chars] as it

Reject GM registration because it cannot support the GETVPN features enabled in the group.

ipsec-getvpn

"Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. "

GDOI-4-GM_RECOVERY_REGISTRATION

4-Warning

GM recovery re-registration for group [chars] will start in a randomly chosen period of [dec] sec

GM recovery feature detects dataplane error and will re-register to KS to refresh keys and policy

-

"Informational message."

GDOI-4-GM_RECOVERY_REGISTRATION_POSTPONED

4-Warning

Detects data error in group [chars] but the previous recovery/rekey has occured within the last recovery-check interval. Postpone recovery registration to start in [dec] sec

GM recovery feature detects dataplane error and will re-register to KS to refresh keys and policy

-

"Informational message."

GDOI-4-GM_SA_TRACK_SET_EOT_ERROR

4-Warning

Group [chars] encountered error in setting EOT object ID [dec] to state [chars].

GM SA TRACK state change occur but fail to update EOT object ID accordingly

-

"Informational message. Check to make sure the EOT " "object ID is configured properly"

GDOI-5-POLICY_CHANGE_ERROR_MULTIPLE_PORTS

5-Notice

Multiple ports detected for ACL [chars] which is not supported. WARNING: No TEK policy will be created.

Informs user that there is an error in the ACL with regards to the number of ports.

ipsec-getvpn

LOG_STD_ACTION

GDOI-6-COOP_KS_VER_TRANSIT

6-Information

Coop KS [chars] protocol version transits from version 1.0.1 to 2.0.0

The KS is transitioning to a new version.

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-COOP_KS_RBLY_FAILED

4-Warning

Coop KS [chars] in group [chars] session Reassembly failed in TransID [dec]

The KS COOP had an error reassmbling a packet from a peer KS

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-COOP_KS_CHECKPT_MISMATCH

4-Warning

Coop KS [chars] in group [chars] received Checkpoint Mismatch message.

The KS COOP had received a checkpoint mismatch from a KS COOP peer

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-COOP_KS_CANNOT_FIND_PROFILE

3-Error

Coop KS in group [chars] has a configured IKEv2 profile '[chars]' that doesn't exist. The COOP will not come up until this error is fixed.

The KS COOP coniguration redunadancy ikve2-profile specifies a profile that doesn't exist. The COOP will not come up.

ipsec-getvpn

LOG_STD_ACTION

GDOI-5-IPSEC_INITIATE_GM_REGISTER

5-Notice

IPSEC initiate GDOI group [chars] to register

IPSEC initiate a GM registration for the group

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-IPSEC_INITIATE_GM_REGISTER_POSTPONE

3-Error

IPSEC triggering registration for group [chars] too frequently. Postpone the registration to occur in [dec] msec.

GM detects IPSEC triggering registration for the group too frequently. GDOI will rate-limit and postpone the registration.

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-3-IPSEC_INITIATE_GM_REGISTER_IGNORE

3-Error

IPSEC triggering registration for group [chars] too frequently. Ignore the request as registartion has already been scheduled to occur in [dec] msec.

GM detects IPSEC triggering registration for the group too frequently. GDOI will ignore the request as registration has already been scheduled.

ipsec-getvpn

"Contact the Group member's administrator."

GDOI-3-COOP_KS_TOO_MANY_GROUPS_SHARE_IKE_SA

3-Error

The COOP KS has too many groups sharing the same IKE SA for the peer addresses local [chars] remote [chars]. Connectivity could be compromised. Please reduce to [dec].

There is a limit to the number of COOP KS groups that can share the. same IKE SA. This can lead to intermittent connectivity for the COOP KS in congested networks

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-COOP_KS_SEND_WINDOW_LIMIT_REACHED

3-Error

The COOP KS has reached its window limit for the peer addresses local [chars] remote [chars]. This is due to connectivity issues between the key servers in question.

The COOP KS running over IKEv2 has a limit to the number of pending messages that can be sent. This limit has been reached which is an indication that there is a connectivity issue between the key servers

ipsec-getvpn

LOG_STD_ACTION

GDOI-4-REJECT_GM_CKM_REGISTER

4-Warning

Reject registration of GM [inet] in group [chars] as it has CKM enabled but this secondaryKS has not sync up all KGS params yet

Reject GM registration because this is a secondaryKS and it has not received KGS seed and rekey-epoch from primaryKS yet

-

LOG_STD_ACTION

GDOI-4-COOP_KS_CKM_INCOMPATIBLE

4-Warning

Found incompatible COOP-KS that cannot support CKM in group [chars]. Please check 'show crypto gdoi feature ckm'and upgrade the incompatible KS immediately.

Found incompatible COOP-KS that cannot support CKM in the group. Network administrator should check 'show crypto gdoi feature ckm'and upgrade the incompatible KS immediately

-

LOG_STD_ACTION

GDOI-5-GM_REGISTER_UPDATE_TBAR

5-Notice

Platform HA forwarding-plane comes online group [chars] gm-identity [chars] fvrf [chars] ivrf [chars] re-register to refresh TBAR info.

HA forwarding-plane comes online group [chars] gm-identity [chars] fvrf [chars] ivrf [chars] is re-registering to refresh TBAR info.

ipsec-getvpn

LOG_STD_ACTION

GDOI-3-GM_IPD3P_NO_IPV6_SUPPORT

3-Error

GETVPN group-member does not support IP-D3P for IPv6.

GETVPN group-member does not support IP-D3P for IPv6.

ipsec-getvpn

"Contact the Administrators to correct the key server policy."

GDOI-3-GM_IPD3P_NO_TRANSPORT_SUPPORT

3-Error

GETVPN group-member does not support IPD3P transport mode

GETVPN group-member does not support IPD3P transport mode

ipsec-getvpn

"Contact the Administrators to correct the key server policy."

GDOI-3-GM_IPD3P_AND_CMD_CANT_COEXIST

3-Error

GETVPN group-member does not support coexistance of IPD3P and Cisco-metadata features

GETVPN group-member does not support the enabling of IPD3P and Cisco-metadata features e.g TBAR-PST SGT at the

ipsec-getvpn

"Contact the Administrators to correct the key server policy."

CRYPTO_HA_IKE-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW

4-Warning

Crypto hardware is enabled and it does not support HA operation '[chars]'

Crypto Hardware is enabled but the hardware does not support HA operations like insert/extract of keys

-

"Replace Cryto hardware with one that support HA operations" " or disable the hardware to use software crypto engine"

CRYPTO_HA_IKE-3-FAILOVER_ERROR

3-Error

Attempt to failover IKE SA [inet]:[inet] failed due to [chars]. No

The HA Active device attempted to checkpoint the state of an IKE SA to the Standby but the Standby device was unable to create the Standby IKE SA.

ipsec-ha

"Look for other error messages at log level WARNING or turn on debugs " "to look for the specific reason of the failure."

CRYPTO_HA_IPSEC-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW

4-Warning

Crypto hardware is enabled and it does not support HA operation '[chars]'

Crypto Hardware is enabled but the hardware does not support HA operations like insert/extract of keys

-

"Replace Cryto hardware with one that support HA operations" " or disable the hardware to use software crypto engine"

CRYPTO_HA_IPSEC-3-FAILOVER_ERROR

3-Error

Attempt to failover IPSec SA [inet]:[inet] failed due to [chars]. No

The HA Active device attempted to checkpoint the state of an IKE SA to the Standby but the Standby device was unable to create the Standby IKE SA.

ipsec-ha

"Look for other error messages at log level WARNING or turn on debugs " "to look for the specific reason of the failure."

CRYPTO_HA_IPSEC-3-HA_IPSEC_UPDATE_PROC_FAIL

3-Error

Start of HA IPSec update process failed

Starting of the IPSec HA process failed Updates will not be sent from active to standby

ipsec-ha

"The box may need to be re-booted if this is a part " "of a IPSec HA setup"

DATA_DESCR-3-HWIDB_DECODE

3-Error

Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]

-

-

-

DATA_DESCR-3-SWIDB_DECODE

3-Error

Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]/[dec]

-

-

-

DATA_DESCR-3-CTRLR_DECODE

3-Error

Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]

-

-

-

DATA_DESCR-3-GENERIC_VIRTUAL_DECODE

3-Error

Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]

-

-

-

DATA_DESCR-3-GENERIC_DECODE

3-Error

Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]/[dec]

-

-

-

DATA_DESCR-3-GENERIC_ENCODE

3-Error

Encode failure: [chars] descriptor type=[dec]

An internal data descriptor could not be encoded for synchronization for the interface or controller in the run-time module specified in the message output. The failure most likely occurred because of a software error. The descriptor type specified in the message output identifies the type of failure. The system state between the active and standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_ACTION

DATA_DESCR-3-DEFER_FAILURE

3-Error

Defer failure on [chars] for descriptor [dec]-[dec]/[dec]/[dec]/[dec]

Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_ACTION

DATA_DESCR-3-QUEUE_INTERNAL_ERROR

3-Error

Internal error on data descriptor queue: [chars]

Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_ACTION

DATA_DESCR-3-ENTRY_EXPIRED

3-Error

Found expired message entry for descriptor [dec]-[dec]/[dec]/[dec]/[dec]

Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized.

ha-idb-sync

LOG_STD_ACTION

ERP_G8032-6-STATE_CHANGED

6-Information

Ethernet ring [chars] instance [dec] changed state to [chars]

Informational message to notify the state transitions for a ring instance

ethernet-g8032

"None. This is an informational message to indicate " "an event may have triggered some ring protection " "action."

ERP_G8032-6-CLEAR_REMINDER

6-Information

Non-revertive ethernet ring [chars] instance [dec] is ready to be cleared by user

Faults have disappeared from a non-revertive ethernet ring instance so now it is ready to be cleared by the user. A non-revertive ring instance by definition requires user action because it does not revert automatically. The act of clearing the ring will cause the location of the block to move to the RPL link and the state to transition to Idle.

ethernet-g8032

"Once ready to move the block to the RPL link the " "ring instance can be cleared with the " "<CmdBold>ethernet ring g8032 clear<noCmdBold> " "command."

ERP_G8032-3-APS_CHANNEL_INACTIVE

3-Error

No longer receiving R-APS messages for ethernet ring [chars] instance [dec]

A ring node has not received R-APS messages on the APS channel for an extended period of time. A properly functioning ring will have an R-APS message transmitted nominally every 5 seconds. This indicates that the requesting transmitting remote node on the ring such as

ethernet-g8032

"Confirm the remote node is transmitting R-APS " "messages and that there is network connectivity on " "the APS channel between the remote node and this " "node."

ERP_G8032-3-PORT_STATE_REQ_ACK_TIMER_EXPIRED

3-Error

No port state ACK received for ring [chars] instance [dec] port [dec] state [dec]

A port state change request was sent to the hardware successfully but an acknowledgement was never received for this request. This means that there is a problem in the hardware.

ethernet-g8032

"This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

ERP_G8032-3-PORT_STATE_REQ_ACK_FAILED

3-Error

Port state negative ACK received for port [chars] state [dec]

A port state change request was sent to the hardware successfully but a negative acknowledgement was received for this request.

ethernet-g8032

"This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

ERP_G8032-3-PORT_STATE_REQ_MAX_LIMIT

3-Error

Port state request has been sent many times and the desired state has not been achieved for port [chars]

A port state change request was sent to the hardware successfully and acknowledgement was received but the desired state was not achieved.

ethernet-g8032

"This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

ERP_G8032-4-FOP_PM_MULTIPLE_RPL_OWNER

4-Warning

RPL Owner node received an R-APSNRRB message from another RPL

RPL Owner node detects a No Request R-APS message with the RPL Blocked status flag set and the Node Id differs from its own. This is a Failure of Protocol - Provision Mismatch due to a misconfiguration where there are multiple RPL Owner nodes configured in the ring.

ethernet-g8032

"Identify the other RPL Owner node with Node Id and " "reconfigure it to be a non-RPL Owner node."

ERP_G8032-4-FOP_PM_LOWER_LEVEL

4-Warning

Node received an R-APS message with Node Id [chars] level [dec] which is lower than configured level [dec] for Ethernet ring [chars] instance [dec]

A ring node detects an R-APS message with a lower level than the configured G.8032 instance level for that APS Channel. This is a Failure of Protocol - Provisioning Mismatch - Level due to a misconfiguration of the APS level of nodes in the ring.

ethernet-g8032

"Identify the other node with Node Id and " "reconfigure it with a matching APS level."

BAP-4-WAVL

4-Warning

Failed to initialize AVL tree BAP not started

BAP will not be operational and will not be negotiated.

-

"Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ <bold> show version <nobold> command to obtain the software version."

BAP-4-NOSTATE

4-Warning

[chars] [chars] [chars] in illegal state [dec]

An internal software error occurred.

-

"Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ <bold> show version <nobold> command to obtain the software version."

PPP-4-IPXNET

4-Warning

mismatched IPX network numbers. Ours = [hec] theirs = [hec]

The two ends of a serial link have different IPX network numbers.

-

"Confirm the configuration of both devices."

PPP-4-NOMAC

4-Warning

Lex ncp: no free Lex interface found with MAC address [enet]

This message indicates that a LAN Extender interface could\n\ not be found with the specified MAC address when bringing up\n\ a LAN Extender link. This is a configuration error.

-

"Refer to the documentation on configuring a LAN Extender\n\ Interface."

PPP-4-NOAPPOINT

4-Warning

MLP Bundle [chars] not appointed

Multilink PPP Bundle was not appointed. Most likely caused by\n\ no memory available

-

"Log show memory summary output. Then analyze output to find\n\ possible memory leak"

PPP-3-MLPFSREENTERED

3-Error

Multilink fastsend reentered bundle [chars] [chars] packet discarded

-

-

-

UNIQ_ADDR-3-DUPL_IPV4

3-Error

A duplicate IPv4 address has been detected [chars] = [inet] already in use by [chars]/[chars]

An access-accept message has been parsed which includes an IPv4 address that already exists in the database. This usually means that the RADIUS server has mistakenly returned an IPv4 address it has returned before.

-

"In the RADIUS server check to see why it is" " returning duplicate IPv4 addresses to the BNG router. At the BNG" " router issue the command 'show ppp all' to see all ppp sessions" " as well as their IP addresses. Useful debugging command are" " 'debug ppp unique address' 'debug radius' and 'debug aaa" "accouting'."

UNIQ_ADDR-3-DUPL_IPV6_PREF

3-Error

A duplicate IPv6 prefix has been detected [chars] = %P already in use by [chars]/[chars]

An access-accept message has been parsed which includes an IPv6 prefix that already exists in the database. This usually means that the RADIUS server has mistakenly returned an IPv6 prefix it has returned before.

-

"In the RADIUS server check to see why it is" "returning duplicate IPv6 prefixes to the BNG router. At the BNG" "router issue the command 'show ppp all' to see all ppp sessions" " as well as their IP addresses. Useful debugging command are" " 'debug ppp unique address' 'debug radius' and 'debug aaa" " accouting'."

UNIQ_ADDR-3-DUPL_IPV6_DEL_PREF

3-Error

A duplicate delegated IPv6 prefix has been detected [chars] = %P already in use by [chars]/[chars]

An access-accept message has been parsed which includes a delegated IPv6 prefix that already exists in the database. This usually meansthat the RADIUS server has mistakenly returned a delegated IPv6 prefix it has returned before.

-

"In the RADIUS server check to see why it is" " returning duplicate delegated IPv6 prefixes to the BNG router." " At the BNG router issue the command 'show ppp all' to see all" " ppp sessions as well as their IP addresses. Useful debugging" " command are 'debug ppp unique address' 'debug radius' and" " 'debug aaa accouting'."

-

3-Error

fmt { \ size_t len = strlen

-

-

-

-

3-Error

fmt { \ size_t len = strlen

-

-

-

-

3-Error

fmt printf

-

-

-

SMART_LIC-6-AGENT_READY

6-Information

SA_NAME is initialized

SA_NAME is fully initialized and ready for use.

smart_agent

-

SMART_LIC-6-AGENT_ENABLED

6-Information

SA_NAME is enabled

SA_NAME is enabled and ready to process licensing requests.

smart_agent

-

SMART_LIC-5-SYSTEM_CLOCK_CHANGED

5-Notice

SA_NAME System clock has been changed

The system clock has changed and the SA_NAME has updated its internal timers

smart_agent

-

SMART_LIC-3-AGENT_REG_FAILED

3-Error

SA_NAME Registration with the CSSM_NAME failed: [chars]

Smart Licensing registration failed. The included error string should give a more detailed reason for the failure. This may have been due to an invalid IDtoken or because the device is already registered

smart_agent

"If the id token was invalid it may be expired or" " you may be using an id token from the Smart Software Manager" " but you are registering with a satellite." " If the device is already registered you may use the force option to" " force the registration with a new id token. " COMM_INFO

SMART_LIC-6-AGENT_REG_SUCCESS

6-Information

SA_NAME Registration successful. udi [chars]

Smart Licensing registration was successful.

smart_agent

-

SMART_LIC-6-AGENT_DEREG_SUCCESS

6-Information

SA_NAME De-registration with the CSSM_NAME was successful

Smart Licensing de-registration successful.

smart_agent

-

SMART_LIC-3-AGENT_DEREG_FAILED

3-Error

SA_NAME DeRegistration with CSSM_NAME failed: [chars]

Smart Licensing De-registration failed. This may have been caused due to a network connection failure to the CSSM_NAME . The local registration information on the device has been removed. The registration information on the CSSM_NAME has not been removed.

smart_agent

COMM_INFO

SMART_LIC-5-IN_COMPLIANCE

5-Notice

All entitlements and licenses in use on this device are authorized

All customer requested entitlements are authorized by Cisco licensing services.

smart_agent

-

SMART_LIC-3-OUT_OF_COMPLIANCE

3-Error

One or more entitlements are out of compliance

The customer is using a license that they have not purchased or they are using more licenses than they have purchased. Sent once when the Out Of compliance state is detected. Sent once per week after that until corrected.

smart_agent

"Customer needs to go to the smart licensing portal " "to view their entitlements to figure out why they are out of compliance."

SMART_LIC-4-IN_OVERAGE

4-Warning

One or more entitlements are in overage

This is for information only. No action is necessary. The customer is still in compliance and within the overage amount as specified in their contract.

smart_agent

-

SMART_LIC-5-EVAL_START

5-Notice

Entering evaluation period

The device is not registered with the CSSM_NAME and is using licenses. A total of 90 days of evaluation period will be available.

smart_agent

"Register this device with the " CSSM_NAME "using an ID token"

SMART_LIC-3-EVAL_EXPIRED

3-Error

Evaluation period expired

Your evaluation period has expired. Some features may restrict their usage. This will be sent once when the evaluation periond expires.

smart_agent

"Customer needs to obtain a new ID token from the " CSSM_NAME " and register the device."

SMART_LIC-5-AUTHORIZATION_EXPIRED

5-Notice

Authorization period expired

The device has not communicated with the CSSM_NAME for 90 days and the device has not automatically renewed the entitlement authorizations. Some features may restrict functionality. This will be sent at the time of expiration and once per week until communications is restored or the registration period expires.

smart_agent

COMM_INFO

SMART_LIC-6-DISABLED

6-Information

SA_NAME disabled

Smart Licensing has been disabled by the customer

smart_agent

-

SMART_LIC-3-BAD_MODE

3-Error

An unknown mode was specified: [dec]

An invalid entitlement enforcement mode was received by the smart agent in the process of logging a syslog message. This is an internal error and should be reported to Cisco

smart_agent.

"This is a Smart Licensing internal error. Please report this to Cisco"

SMART_LIC-3-BAD_NOTIF

3-Error

A bad notification type was specified: [dec]

This is an internal Smart Licensing error. Report it to Cisco TAC

smart_agent

CALL_TAC

SMART_LIC-3-ID_CERT_EXPIRED

3-Error

Registration period has expired. Smart Licensing will transition to the unregistered state. Please re-register this product to correct the problem.

The current time is outside the valid registration period in the ID certificate. This could be caused by a change in the system clock or multiple communications failures with the CSSM_NAME

smart_agent

"Please check the Smart Call Home settings and " "network connectivity to the " CSSM_NAME ". Also verify your system " "clock is correct"

SMART_LIC-6-ID_CERT_RENEW_SUCCESS

6-Information

Automatic registration renewal successful

Customer ID certificate has been renewed successfully

smart_agent

-

SMART_LIC-3-ID_CERT_RENEW_NOT_STARTED

3-Error

ID certificate start date not reached yet

The device registration failed. The ID Certificate start date is later than the device current time.

smart_agent

"Please adjust your device clock to be correct " "and retry the registration again."

SMART_LIC-3-ID_CERT_RENEW_FAILED

3-Error

Automatic registration renewal failed: [chars]

The automatic ID certificate registration renewal failed.

smart_agent

COMM_INFO

SMART_LIC-6-ENTITLEMENT_RENEW_SUCCESS

6-Information

Entitlement authorization renewal with CSSM_NAME successful

Authorization renewal request is successful.

smart_agent

-

SMART_LIC-3-ENTITLEMENT_RENEW_FAILED

3-Error

Entitlement authorization with CSSM_NAME failed: [chars]

The device has failed to communicate with Cisco to renew the entitlement authorization.

smart_agent

COMM_INFO

SMART_LIC-3-COMM_FAILED

3-Error

Communications failure with the CSSM_NAME : [chars]

The device communication with the CSSM_NAME failed. This wil be sent for every communications attempt that fails. Additionally it will be sent once per week until communications are restored.

smart_agent

COMM_INFO

SMART_LIC-5-COMM_RESTORED

5-Notice

Communications with the CSSM_NAME restored

Smart Agent communication with the CSSM_NAME has been restored.

smart_agent

-

SMART_LIC-3-CERTIFICATE_VALIDATION

3-Error

Certificate validation failed: [chars]

The ID certificate validation failed during a reboot registration or renewal. The included error message should give more information about the failure

smart_agent

-

SMART_LIC-5-COMM_INIT_FAILED

5-Notice

Failed to initialize communications with the CSSM_NAME : [chars]

Smart Licensing could not initialize communication with the CSSM_NAME

smart_agent

COMM_INFO

SMART_LIC-6-AUTH_RENEW_SUCCESS

6-Information

Authorization renewal successful. State=[chars] for udi [chars]

The automatic authorization renewal was successful

smart_agent

-

SMART_LIC-3-AUTH_RENEW_FAILED

3-Error

Authorization renewal with the CSSM_NAME : [chars] for udi [chars]

The Authorization renew request failed. This will be sent every time an authorization attempt fails and once per week whinle in the failed state. An automatic retry will occur on the following schedule: If smart licensing is in the authorized state every 23 hours. If smart licensing is in the Out of Compliance state every 15 minutes for the first two hours then once every four hours after that. If smart licensing is in the authorization expired state then once every hour.

smart_agent

COMM_INFO

SMART_LIC-6-HA_ROLE_CHANGED

6-Information

Smart Agent HA role changed to [chars].

Smart Agent role on HA RP has been changed to either active or standby.

smart_agent

-

SMART_LIC-3-INVALID_TAG

3-Error

The entitlement tag is invalid: [chars]

The entitlement tag for a license is not defined in the CSSM_NAME . This is a Cisco internal problem and should be reported to Cisco.

smart_agent

"report this error to Cisco"

SMART_LIC-6-HA_CHASSIS_ROLE_CHANGED

6-Information

Smart Agent HA chassis role changed to [chars].

Smart Agent chassis role on HA has been changed to either active or standby.

smart_agent

-

SMART_LIC-3-INVALID_ROLE_STATE

3-Error

The current role is not allowed to move to the new role: Current [chars] New [chars]

From the last HA role event we can only move to certain roles. The device has moved to a role which the Smart Agent cannot follow.

smart_agent

"Report this problem to Cisco"

SMART_LIC-4-EVAL_WILL_EXPIRE_WARNING

4-Warning

Evaluation period will expire in [chars].

The device is using the evaluation period which will expire in the specified time. This will be sent at the following intervals prior to expiration: 60 days 30 days every week in the last 30 days every day in the last week every hour in the last day.

smart_agent

"Register this device with the " CSSM_NAME " before the evaluation period expires."

SMART_LIC-3-EVAL_EXPIRED_WARNING

3-Error

Evaluation period expired on [chars]

The evaluation period expired at the time specified. This will be sent once per week after expiration if the product is not registered.

smart_agent

"Register this device with the " CSSM_NAME " before the evaluation period expires."

SMART_LIC-3-ID_CERT_EXPIRED_WARNING

3-Error

This device's registration will expire in [chars].

The registration for this device will expire at the specified time. This usually indicates a communications failure with the CSSM_NAME . This will be sent at the following interval prior to expiration: 60 days 30 days every week in the last 30 days every day in the last week every hour in the last day.

smart_agent

COMM_INFO

SMART_LIC-7-DAILY_JOB_TIMER_RESET

7-Debug

Daily job timer reset

This message is used only for testing and does not indicate an error

smart_agent

-

SMART_LIC-6-AGENT_ALREADY_REGISTER

6-Information

This device is already registered with the CSSM_NAME .

Smart Licensing on this device has already registered with the CSSM_NAME

smart_agent

"Use the force option when registering or " "remove this device from your virtual account on the " CSSM_NAME

SMART_LIC-6-AGENT_ALREADY_DEREGISTER

6-Information

Smart Agent is already Deregistered with the CSSM.

Smart Licensing has already de-registered with Cisco.

smart_agent

-

SMART_LIC-3-CONFIG_OUT_OF_SYNC

3-Error

Trusted Store Enable flag not in sync with System Configuration TS [chars] Config [chars]

Smart Licensing Configuration does not match the value of the enable flag in Trusted Store. This can happen if a configuration is copied onto the system and a reload occurs. If the new configuration does not contain the Smart Licensing Enable command the value in Trusted Store will not match.

smart_agent

"Apply the desired Smart Licensing Configuration Command and persist the configuration."

SMART_LIC-3-REG_EXPIRED_CLOCK_CHANGE

3-Error

Smart Licensing registration has expired because the system time was \changed outside the validity period of the registration period. The agent will transition to the un-registered state\ in 60 minutes.

The system clock has been changed so that it is now outside the valid registration \period. If the clock is reset to a value inside the registration validity period \within one hour smart licensing will continue function normally. If the clock is \not reset the device will become un-registered and a new id token will need to be \obtained to re-register the device. The registration validity period is defined by \the start and end date in the id certificate. use 'show license tech support' to get the id \certificate information.

smart_agent

"Set the system clock back to the correct date and time"

SMART_LIC-3-ROOT_CERT_MISMATCH_DEV

3-Error

Certificate Mismatch: \Development [chars] Certificate being used with a Production Root Certificate. \Use the \'test license smart dev-cert enable\' CLI to set the DEV root cert.

The Production Root Certificate is being used with \Development certificates.

smart_agent

"Please activate the Development Root Certificate \from the CLI. ie. \'test license smart dev-cert enable\'"

SMART_LIC-3-ROOT_CERT_MISMATCH_PROD

3-Error

Certificate type mismatch. Development Root Certificate is being used with Production certificates.

The Development Root Certificate is being used with Production certificates. Someone used a test command to set the Development root certificate but the systems is connected to the production CSSM

smart_agent

"Use the test command to reset the certificate."

SMART_LIC-3-HOT_STANDBY_OUT_OF_SYNC

3-Error

Smart Licensing agent on hot standby is out of sync with active Smart Licensing agent

Smart Licensing Agent on the hot standby failed to process the data necessary to stay in sync with the active agent. If a switch over occurs the the new active agent will not be in the same state as the current active agent Configuration does not match the value of the enable flag in Trusted store. This can happen if a configuration is copied onto the system and a reload occurs. If the new configuration does not contain the Smart Licensing Enable command the value in Trusted Store will not match.

smart_agent

"Ensure that the configuration is the same on both systems."

SMART_LIC-6-EXPORT_CONTROLLED

6-Information

Usage of export controlled features is [chars]

This tells the customer if usage of export controlled features or a particular feature is allowed or not allowed

smart_agent

-

SMART_LIC-3-EXPORT_REQUEST_FAILURE

3-Error

The export authorization key request for [chars] failed: [chars]

The request for the export authorization key has failed. The export restricted feature that needs this key will not enable.

smart_agent

-

SMART_LIC-6-EXPORT_HA_MISMATCH

6-Information

The export authorization key information on the active and standby does not match. Licensing HA will not work properly: [chars]

The standby or members to not have the export authorization keys for all the same features as the active has. If the standby takes over as active you will not have the same licenses available and your device may not work properly.

smart_agent

"Get proper export authorization keys on all nodes" " using the 'license smart export request all' command. Use the" " 'license show status' command to see the export status of all" " standby or member devices."

SMART_LIC-4-EXPORT_NOT_SUPPORTED

4-Warning

The satellite this device is connected to is an older version that does not support export authorization keys.

The satellite this device is connected to is an older version that does not support export authorization keys and a request for an export authorization key has been made.

smart_agent

"Either update the satellite to the latest version" " that supports export authorization keys or change the URL on this" " device to point to a different satellite."

SMART_LIC-2-PLATFORM_ERROR

2-Critical

Smart Licensing has encountered an internal software error. Contact TAC: [chars]

Smart Licensing Agent has encountered an internal Platform Problem. this indicates that the platform team did not properly implement Smart licensing on the device. The Platform Development Team needs to be contacted to get this problem addressed. This should never happen at a customer site

smart_agent

"The customer should contact TAC. The platform team needs to address this problem before release"

SMART_LIC-6-HOSTNAME_MATCHED_UDI

6-Information

The host name has been changed to match a field in the device identifier UDI.

The host name has been changed to match a field in the device identifier UDI. Since the device identifier is sent to Cisco this may bypass your host name privacy settings. You can view the device identifier with the command \show license udi\.

smart_agent

"Change the host name so it does not include any fields in the device identifier."

SMART_LIC-3-DEPRECATED_API

3-Error

The Deprecated function [chars] has been called.This call should be replaced by [chars]

This error indicates the platform team is using deprecated API functions. The platform code is calling a deprecated function. The code needs to be changed to call the new function

smart_agent

"Contact Cisco TAC.The platform team needs to address this problem before release"

SMART_LIC-6-RESERVED_INSTALLED

6-Information

[chars] License Reservation Authorization code installed for udi [chars]

A reservation authorization code was successfully installed.

smart_agent

-

SMART_LIC-4-RESERVE_IN_PROGRESS

4-Warning

[chars] License Reservation process must be completed with the 'license smart reservation install' command. Reservation started on [chars]

A reservation request is in progress. This will be sent every day until a reservation authorization code is installed.

smart_agent

"Customer needs to get a reservation authorization " "code from the " CSSM_NAME " and install it on " "the device"

SMART_LIC-6-RESERVE_RETURNED

6-Information

[chars] License Reservation returned for udi [chars]. Smart Agent is now unregistered.

The reservatio authorization code has been returned. This will cause Smart Licensing to transition back to the un-registered state and start consuming the evaluation period.

smart_agent

-

SMART_LIC-6-RESERVE_CANCELED

6-Information

License Reservation request canceled for udi [chars]. Smart Agent is now unregistered.

Sent when the customer cancels a reservation request by using the reservation cancel command

smart_agent

-

SMART_LIC-6-RESERVE_AUTH_FAILED

6-Information

Failed to validate the [chars] Reservation Authorization Code for udi [chars]. Changing to the unregistered state.

The reservation authorization code that was installed is not valid on this device.

smart_agent

"Get a new reservation authorization code and install it."

SMART_LIC-3-RESERVE_HA_FAILURE

3-Error

The license reservation information on the active and standby does not match. Licensing HA will not work properly: [chars]

In HA configuration if there is any mismatch in reservation configuration between the nodes this notification is to be send. The values to be compared for determining mismatch between nodes are - reservation enable state reservation version reservation type authorization code validation status and export enable status. If the standby takes over as active you will not have the same licenses available and your device may not work properly.

smart_agent

"Change reservation configuration in either/both " "the nodes to match each other"

SMART_LIC-6-RESERVE_HA_MISMATCH

6-Information

The reserved licenses on the active and standby do not match. Use the 'show license status' command to see the exact error.

The Licenses reserved using the Specified License Reservation SLR feature in Smart Licensing and installed on the

smart_agent

"Ensure that the reservation authorization codes " "installed on all HA systems are for the same licenses. "

SMART_LIC-3-PLR_CONFIG_OUT_OF_SYNC

3-Error

Trusted Store PLR Enable flag not in sync with System Configuration TS [chars] Config [chars]

Smart Licensing Configuration does not match the value of the PLR enable flag in Trusted Store. This can happen if a configuration is copied onto the system and a reload occurs. If the new configuration does not contain the Smart Licensing Enable command the value in Trusted Store will not match.

smart_agent

"Apply the desired Smart Licensing PLR Configuration Command and persist the configuration."

SMART_LIC-6-PLR_DISABLED_INIT_COMM

6-Information

Permanent License Reservation has been disabled. Please reboot the system to initialize Smart Licensing communications with Cisco.

During bootup Smart Licensing communications is not initialized if Permanent License Reservation PLR is enabled. To enable Smart Licensing

smart_agent

"reboot the system"

SMART_LIC-4-CONFIG_NOT_SAVED

4-Warning

Smart Licensing configuration has not been saved

This is only an informational message to the customer to remind them to save the configuration

smart_agent

"save the configuration"

SMART_LIC-3-CONFIG_NOT_SAVED_TSCLEAR

3-Error

The smart agent for Licensing will now be disabled because the config was not saved before the reload

During Smart Agent initialization if the Smart Agent state is registered and the config with the smart license enabled flag was saved before the reboot then this means the config was not saved before the reload.

smart_agent

"save the configuration before reloading"

SMART_LIC-2-XDM_DISPATCH_LOOP_FAILURE

2-Critical

SmartAgent Admin Init Failed due to failure at XdmDispatchLoop in creating handle

This is an internal error During scheduler init when trying to create xdm handle it is failing!

smart_agent

CALL_TAC

SMART_LIC-4-HANDLE_ATTR_VERSION_MISMATCH

4-Warning

The handle attribute version between two devices are different. [chars]

The devices inside a cluster do not have the same operational capability. This is not an issue if all devices use only the functionality that is supported by all members of a stack or cluster. However it's a good practice to have have all devices in a stack or cluster use the same software version.

smart_agent

"Ensure that all devices in the stack or cluster " "are using the same version of the software."

SMART_LIC-3-APPHA_DUPLICATED_PEER

3-Error

The Application HA Cluster already has a member with given identity. Use the 'show license usage' command to see the exact error.

When setting up peer information for an entitlement that supports attribute the given peer information already exists. This means one of the device may not be configured correctly or logics that suppose to remove peer information is not working correctly.

smart_agent

CALL_TAC

SMART_LIC-3-APPHA_MISSING_PEER

3-Error

The Application HA Cluster doed not have a member with given identity. Use the 'show license usage' command to see the exact error.

When removing peer information for an entitlement that supports attribute the given peer information does not exists. This means one of the device may not be configured correctly or logics that suppose to add/update peer information is not working correctly.

smart_agent

CALL_TAC

SMART_LIC-3-APPHA_ADD_ITSELF

3-Error

The Application is trying to add itself as its own Application HA peer.

When adding peer informations for an entitlement that supports attribute peerInfo contains same data as It's own HA attribute. This means that it tried to add itself as its own peer.

smart_agent

CALL_TAC

SMART_LIC-3-APPHA_DUPLICATED_INSTANCE

3-Error

The Application is trying set HA information for a duplicate instance.

When setting HA informations for an entitlement instance handle another instance is found with same

smart_agent

CALL_TAC

SMART_LIC-6-CONVERT_START

6-Information

Smart License Conversion has started

The smart agent for licensing has initiated the conversion process to convert traditional licenses to smart licenses and to deposit those licenses into the customers smart account.

smart_agent

-

SMART_LIC-6-CONVERT_LIC_SUCCESS

6-Information

[chars] License [chars] has been converted to [chars] with a count of [dec]

The traditional license specified has been converted to a smart license and has been deposited into the customers smart account.

smart_agent

-

SMART_LIC-6-CONVERT_LIC_ALREADY

6-Information

[chars] License [chars] has been converted to [chars] with a count of [dec]

The traditional license specified has been previously been converted to a smart license and has previously been deposited into the customers smart account.

smart_agent

-

SMART_LIC-3-CONVERT_LIC_FAIL

3-Error

[chars] Failed to convert [chars]: [chars]

The traditional license specified failed the conversion process. The reason for this is detailed in the message.

smart_agent

-

SMART_LIC-6-CONVERT_SUCCESS

6-Information

[chars] Smart License Conversion successful

The entire license conversion process was successful. All licenses have been deposited into the customer's smart account.

smart_agent

-

SMART_LIC-6-CONVERT_ALREADY

6-Information

[chars] Smart License Conversion successful

A license conversion has already been done for the UDI specified. Only one conversion process is allowed.

smart_agent

-

SMART_LIC-3-CONVERT_FAILED

3-Error

[chars] License conversion failed: [chars]

The conversion process failed. The reason for this is detailed in the message.

smart_agent

-

SMART_LIC-6-THIRDPARTY_MODE_ENABLED

6-Information

SA_NAME is in Thirdparty Mode

SA_NAME is in thirdparty mode and ready to collect and process RUM reports

smart_agent

-

SMART_LIC-6-THIRDPARTY_MODE_DISABLED

6-Information

SA_NAME is out of Thirdparty Mode

SA_NAME is out of thirdparty mode and has stopped collecting and processing RUM reports

smart_agent.

-

SMART_LIC-3-UTILITY_EXPIRED

3-Error

SA_NAME Utility certificate has expired.

SA_NAME utility certificate has expired. This means that the registration period has expired. Smart Licensing will transition to the unregistered state. Please re-register this product to correct the problem.

smart_agent

"Please check the communications settings and " "network connectivity to the " CSSM_NAME " or satellite." "Also verify your system clock is correct"

SMART_LIC-3-UTILITY_RENEW_FAILED

3-Error

SA_NAME Utility certificate renewal failed

SA_NAME Utility cert renew failed this will occur once per day until the renewal is successful or the current certificate expires

smart_agent

"Please check the communications settings and " "network connectivity to the " CSSM_NAME " or satellite." "Also verify your system clock is correct"

SMART_LIC-5-UTILITY_RENEW_SUCCESS

5-Notice

SA_NAME Utility certificate renewal successful

-

smart_agent

-

SMART_LIC-6-UTILITY_STARTED

6-Information

SA_NAME Utility has started sending usage reports

SA_NAME utility has been enabled to the point where we are sending usage reports

smart_agent

-

SMART_LIC-6-UTILITY_STOPPED

6-Information

SA_NAME Utility has stopped sending usage reports: [chars]

SA_NAME Utility is not available and no longer sending usage reports.

smart_agent

-

SMART_LIC-3-UTILITY_REPORT_FAILED

3-Error

SA_NAME Utility has failed to send usage Report

Smart licensing failed to send a usage report because of a network error.

smart_agent

"Please check the communications settings and " "network connectivity to the " CSSM_NAME " or satellite."

SMART_LIC-4-UTILITY_FQDN_MISMATCH

4-Warning

SA_NAME Utility URL setting does not match the FQDN in the utility certificate.

SA_NAME Smart licensing url setting must match the FQDN embedded in the utility certificate

smart_agent

" Get a new utility certificate from Cisco."

SMART_LIC-4-SMART_TRANSPORT_NOT_CONFIG

4-Warning

SA_NAME Smart transport is not configured for utility reporting

SA_NAME Utility is enabled and we have a subscription but Smart transport is not configured.

smart_agent

"Enable and configure the smart transport"

SMART_LIC-3-NOT_AUTHORIZED

3-Error

The entitlement [chars] is Not Authorized to be used. Reason: [chars]

The customer is using a license that they are not authorized to use.

smart_agent

"Customer needs to go to the smart licensing portal " "to view their entitlements to figure out why they are not authorized " "to use this license."

SMART_LIC-5-SLR_IN_COMPLIANCE

5-Notice

The entitlement [chars] in use on this device is authorized

The customer has requested for an entitlement that they are authorized to use.

smart_agent

-

SMART_LIC-6-RESERV_AUTH_ALREADY_INSTALLED

6-Information

Same Reservation Authorization Code already installed for UDI: [chars].

A list of reservation authorization codes is being installed. One of the authorization codes is in the list twice and has already been installed.

smart_agent

-

SMART_LIC-3-RESERV_NO_AUTH_CODE_FOUND

3-Error

No authorization code found in meta file which matches with any udi in stack.

The customer is using a meta file which does not contain any authorized code for this HA stack

smart_agent

"Customer needs to use a meta file which contains " "authorized codes for this HA stack"

SMART_LIC-3-RESERV_DUP_AUTH_CODE_FOUND

3-Error

Duplicate authorization code found in meta file for one device in HA stack for use [chars].

The customer is using a meta file which contains Duplicate authorization code for one device in HA stack

smart_agent

"Customer needs to use a meta file which contains " "only one authorized code for each device in HA stack"

SMART_LIC-3-RESERV_FAIL_GEN_RETURN_CODE

3-Error

Unable to generate authorization return code for [chars].

Smart Licensing is unable to generate an authorization return code. The reservation authorization code has been removed from the system. To return the license to the smart account please contact TAC.

smart_agent

CALL_TAC

SMART_LIC-3-EVENT_LOG_WRITE

3-Error

Writing to Event Log File failed

It is failure in writing EventLogFile. It is the first occurence of the failure. Syslog will not be sent for subsequent failure for write of the same file

smart_agent

-

SMART_LIC-3-EVENT_LOG_READ

3-Error

Reading from Event Log file \ failed

Can't get log or allocate enough space to return the log in a buffer

smart_agent

-

SMART_LIC-5-END_POINT_RESET

5-Notice

End Point list reset

Complete list of End Points has to be reported to CSSM. Agent has just initiated Authorization request after registration

smart_agent

"Complete end point list for all the licenses has " "to be reported by the product instance."

SMART_LIC-5-END_POINT_RESET

5-Notice

-

-

-

-

DEAD-4-SCARLET

4-Warning

* Interface [chars]: I knew without asking she was into the blues

-

-

-

DEAD-4-SCARLET

4-Warning

-

-

-

-

-

4-Warning

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

FMD-1-MALPINITFAILED

1-Alert

MAL process failed creation

System is going through a software error and has failed to create a process

-

LOG_STD_SH_TECH_ACTION

FMD-3-LOOKUPFAILED

3-Error

Lookup failed for the flow of source_ip: [dec] dest_ip: [dec] source_port: [dec] dest_port: [dec] l4_protocol: [dec] class_id: [dec] vrf_table_id: [dec]

This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n This entry is not present in the Flow Table for the 4 Tuple It might because the Table is not populated for the flow \n The flow would have been deleted \n

-

"If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative."

FMD-3-DELETENODEFAILED

3-Error

Lookup failed for the flow of source_ip: [dec] dest_ip: [dec] source_port: [dec] dest_port: [dec] l4_protocol: [dec] class_id: [dec] vrf_table_id: [dec]

This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n This entry is not present in the Flow Table for the 4 Tuple to delete the node It might because the Table is not populated for the flow \n The flow would have been deleted \n

-

"If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative."

FMD-3-MEMALLOCFAILED

3-Error

Memory Allocation failed

This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n The memory might be full due to Flow Limit Exceeded.\n The Memory Leak would have happened.\n

-

"If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative."

FMD-3-NULL

3-Error

System receieved an invalid NULL pointer

This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to a software error.\n

-

"If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative."

FMD-3-DBINITFAILED

3-Error

Database Init failed

This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to resource unavailability the INIT would have been failed.\n

-

"If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative."

FMD-3-TRANSPORT

3-Error

Operation [chars] on transport layer failed due to [chars]

This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to a software error.\n

-

"If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative."

FMD_ISSU-2-INIT

2-Critical

FMD ISSU client initialization failed to [chars]. Error: [dec] [chars]

The FMD ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

medianet-metadata

LOG_STD_ACTION

FMD_ISSU-3-TRANSFORM_FAIL

3-Error

FMD ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The FMD ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the FMD state between the active device and the standby device is not identical.

medianet-metadata

"show issu session <client_id> and " "show issu negotiated version <session_id>"

FMD_ISSU-3-MSG_NOT_OK

3-Error

FMD ISSU client 'Message Type [dec]' is not compatible

The FMD ISSU client received an incompatible message from the peer device. The message cannot be processed.

medianet-metadata

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

FMD_ISSU-3-MSG_SIZE

3-Error

FMD ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The FMD ISSU client failed to calculate the MTU for the specified message. The FMD ISSU client is not able to send the message to the standby device.

medianet-metadata

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

FMD_ISSU-3-INVALID_SESSION

3-Error

FMD ISSU client does not have a valid registered session.

The FMD ISSU client does not have a valid registered session.

medianet-metadata

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

FMD_ISSU-2-SESSION_REGISTRY

2-Critical

FMD ISSU client failed to register session information. Error: [dec] [chars]

The FMD ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

medianet-metadata

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

FMD_ISSU-3-SESSION_UNREGISTRY

3-Error

FMD ISSU client failed to unregister session information. Error: [dec] [chars]

The FMD ISSU client failed to unregister session information.

medianet-metadata

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

FMD_ISSU-2-SESSION_NEGO

2-Critical

FMD ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The FMD ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

medianet-metadata

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

FMD_ISSU-2-SEND_NEGO_FAILED

2-Critical

FMD ISSU client failed to send negotiation message. Error: [dec] [chars]

The FMD ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

medianet-metadata

"show logging and show checkpoint client"

FMD_ISSU-2-GET_BUFFER

2-Critical

FMD ISSU client failed to get buffer for message. Error: [dec] [chars]

The FMD ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

medianet-metadata

"show logging and show checkpoint client"

FMD_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER

3-Error

'Message Type [dec]' is not supported by FMD ISSU client at peer

The FMD ISSU client at the peer supervisor is not compatible for this message type. The FMD client will be marked as incompatible with the peer.

medianet-metadata

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

FMD_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

FMD ISSU client capability exchange result incompatible.

The FMD ISSU client capability exchange have negotiated as incompatible with the peer.

medianet-metadata

"show issu negotiated capability <Session_ID>"

FMD_ISSU-3-CAP_INVALID_SIZE

3-Error

FMD ISSU client capability list is empty.

The FMD ISSU client capability exchange list size is invalid.

medianet-metadata

"show issu capability entires <Client_ID>"

PIM_PROT-3-IDB_CREATE

3-Error

Interface Manager error - [chars] in [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-6-IDB_ENABLE

6-Information

Interface [chars] does not support multicast not enabled

PIM not enabled on an interface that does not support mcast

ipmulticast

LOG_STD_NO_ACTION

PIM_PROT-3-RP_INIT

3-Error

[chars] in [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-LIST_ERR

3-Error

List error in [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-SRC_UPDATE_ERR

3-Error

Error in [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-SHUTDOWN_ERR

3-Error

Error in [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-PROTOCOL_ERR

3-Error

[chars] - [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-4-PROTOCOL_WARNING

4-Warning

[chars] - [chars] [chars] : [chars]

Internal protocol inconsistency warning

ipmulticast

LOG_STD_NO_ACTION

PIM_PROT-3-PAK_ERR

3-Error

An internal error occured while processing a packet queue

Managed queue event received without a packet. Internal Error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-INTERNAL_ERR

3-Error

[chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-MSG_SEND_ERR

3-Error

[chars]

An internal error occured while trying to send a message. Events scheduled to happen on reception of the message like deletion of the pim tunnel idb may not take place.

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-NULL_UNIT

3-Error

NULL input pointer parameter for getting register tunnel unit

A NULL input parameter was specified in a function call to obtain the register tunnel IDB unit number associated with a rendezvous point IP address. The register tunnel for this rendezvous point can not be allocated.

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-4-SUSPEND_RESUME_WARNING

4-Warning

Failed to resume suspended PIM context.

A loop in PIM code was temporarily suspended to avoid hogging the CPU. When it was time to resume the loop the system was unable to do so. Possible reasons for this are that a VRF was deleted or an interface was deleted while the loop was suspended.

ipmulticast

LOG_STD_NO_ACTION

PIM_PROT-3-TABLE_ERR

3-Error

[chars]

Errors related to PIM table creation and management

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-3-WAVL_INIT

3-Error

[chars]

Error initializing the ole WAVL tree

ipmulticast

LOG_STD_RECUR_ACTION

PIM_PROT-4-MROUTELIMIT

4-Warning

Current count of [dec] exceeds multicast route-limit of [dec]

The number of multicast routes equals the configured maximum allowed.\n\ New routes cannot be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried\n\ by this router then use the 'ipv6 multicast route-limit' command to\n\ increase the number of multicast routes.\n\ Otherwise no action is required."

PIM_PROT-4-MROUTELIMIT_ATTEMPT

4-Warning

Attempt to exceed multicast route-limit of [dec]

The number of multicast routes equals the configured maximum allowed.\n\ New routes cannot be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried\n\ by this router then use the 'ipv6 multicast route-limit' command to\n\ increase the number of multicast routes.\n\ Otherwise no action is required."

PIM_PROT-4-MROUTELIMITWARNING

4-Warning

multicast route-limit warning curr [dec] threshold [dec]

-

-

-

MDT-4-LBSRC

4-Warning

MDT [chars] uses source address [inet] from a non-loopback interface

The local peering interface used to set up MDT tunnel is not a\n loopback Interface. This may cause blackholes if the interface is\n in the outgoing list of the MDT group.

-

"Change the configuration of bgp update-source and use a loopback\n" "interface as the local peering interface"

MDT-4-VRFSRC

4-Warning

The source interface of the MDT tunnels [chars] is not in the global table

The local peering interface must not be an interface in a VRF.

-

"Change the configuration of bgp update-source and use a loopback\n" "interface in the global table"

MDT-4-NO_GROUP_LINK

4-Warning

MDT entry [chars]:[inet][inet] linked by source but not linked by group

-

-

-

MDT-4-RD_CONFLICT

4-Warning

MDT entry [chars]:[inet][inet] received an update for RD [chars]

-

-

-

MDT-3-POOL_GROUP

3-Error

Failed attempt to find MDT group [chars] in pool for mvrf [chars]

An attempt to allocate an MDT data pool entry on a standby RP using an MDT data group address previously allocated on the active RP has failed. The specified group address does not exist in the group address pool for this MVRF on the standby RP. MVPN traffic may be impeded for this MVRF following an RP failover.

-

LOG_STD_ACTION

MDT-5-DATA_MDT_REUSED

5-Notice

Data MDT [chars] is reused

A data MDT group can be reused by a particular host that sources\n\ user traffic in an VPN if all pre-defined data MDT groups are used

-

LOG_STD_NO_ACTION

MDT-4-UPDATED_RD_CONFLICT

4-Warning

MDT entry [chars]:[inet][inet] received an update for RD [chars]

-

-

-

MDT-4-MVPN_ROUTELIMIT_ATTEMPT

4-Warning

MVPN update caused attempt to exceed multicast route-limit of [dec]

The number of multicast routes equals the configured maximum allowed.\n\ A new multicast route creation request that was triggered by an\n\ MVPN BGP/PIM update from a peering PE router by an MVPN\n\ configuration action on this router or by an MDT default/data\n\ transition on this router could not be added. No new routes can\n\ be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried\n\ by this router then use the 'ip multicast route-limit' command to\n\ increase the number of multicast routes.\n\ Otherwise no action is required."

MDT-4-NO_TDB_PDB

4-Warning

No protocol descriptor block for TDB at 0x[hec]: [chars] failed

The operation can not be executed because the MVPN table is not \n\ fully initialized

-

LOG_STD_ACTION

MDT-4-PIM_TDB_TRANS

4-Warning

MVPN TDB to [chars] translation failed for AF [chars]

The operation can not be executed because a NULL or incorrect \n\ MVPN table was specified.

-

LOG_STD_ACTION

MDT-3-NOPDB

3-Error

No protocol descriptor block for MVPN protocol type [dec]

MVPN configuration commands can not be executed because \n\ there are no functions registered for handling this command \n\ address family.

-

LOG_STD_ACTION

MDT-3-NO_CORE_TDB

3-Error

No core table descriptor block for MVPN address family [chars]

MVPN configuration commands can not be executed because \n\ there are is no MVPN core table for the specified address family.

-

LOG_STD_ACTION

MDT-3-BAD_TABLEID

3-Error

Invalid VRF table ID 0x[hec]

This MVPN configuration command can not be executed because \n\ the received VRF table ID is not valid.

-

LOG_STD_ACTION

MDT-3-NODETAIL

3-Error

Missing detail information

The detailed information requested for the currently executing \n\ show command was not collected as required. The show command \n\ processing is aborted.

-

LOG_STD_ACTION

MDT-3-LPBACK_CONV

3-Error

Loopback Conversion Failed.

Installation of required MVPN forwarding interfaces may have \n\ failed for one or more MDT groups.

-

LOG_STD_ACTION

MDT-3-ALLOC_SHOW_ENTRY

3-Error

Attempt to allocate show entry for invalid show type [dec]

The show data type specified by the function attempting to perform a show operation is not a valid type. The show operation can not be performed.

-

LOG_STD_SH_TECH_ACTION

MDT-3-IDB_ROUTE_DISABLE

3-Error

Tunnel Groups: [chars]: [chars]

BGP AD update contains tunnel type that's different from the locally configured group to tunnel type mapping.

ip-tunnels

"Ensure the group to tunnel type mapping is consistent between PE peers."

MDT-3-INVALID_ADDR_COPY

3-Error

Invalid or incompatible address copy type [dec] and length [dec]

An IP address copy operation for an MVPN data state transition failed because the specified address type and address length did not match any defined IP address category.

-

LOG_STD_SH_TECH_ACTION

MDT-2-MVPN_PE_CHUNK_ERR

2-Critical

Error initializing MVPN PE chunk

Chunk memory for MVPN PE cannot be initialized

-

LOG_STD_NO_ACTION

MDT-2-MVPN_BGP_UPDATE_CHUNK_ERR

2-Critical

Error initializing MVPN BGP Update chunk

Chunk memory for MVPN BGP Update cannot be initialized

-

LOG_STD_NO_ACTION

MDT-2-MVPN_BGP_LEAF_AD_UPDATE_CHUNK_ERR

2-Critical

Error initializing MVPN BGP Leaf AD Update chunk

Chunk memory for MVPN BGP Leaf AD Update cannot be initialized

-

LOG_STD_NO_ACTION

MDT-2-MVPN_REPL_CHUNK_ERR

2-Critical

Error initializing MVPN repl db chunks

Error initializing MVPN repl db chunks

-

LOG_STD_NO_ACTION

MDT-2-MVPN_REPL_RADIX_BRANCH_ERR

2-Critical

Error initializing MVPN replication branch radix tree

Internal error

-

LOG_STD_NO_ACTION

MDT-3-WAVL_INIT_FAIL

3-Error

Failed initializing [chars] wavl tree.

wavl_init failed.

mcast-mvpn

LOG_STD_ACTION

MDT-2-TDB_ID_INIT_FAIL

2-Critical

[chars] - Failed initializing tdb id.

Internal identification number of MVPN tdb cannot be initialized.

mcast-mvpn

LOG_STD_ACTION

MDT-5-TDB_ID_NOT_INIT

5-Notice

[chars] - tdb id not initialized.

Internal identification number of MVPN tdb is not initialized.

-

LOG_STD_NO_ACTION

MDT-2-TDB_ID_MISMATCH

2-Critical

[chars] - Mismatch between current tdb id [dec] and synced id [dec].

Internal identification number of MVPN tdb is mismatched with synced id.

mcast-mvpn

LOG_STD_ACTION

MDT-2-PE_LSPVIF_CREATE_FAIL

2-Critical

[chars] - LSPVIF creation for PE [chars] failed.

The creation of LSPVIF for a remote PE for strong RPF check has failed.

mcast-mvpn

LOG_STD_ACTION

MDT-3-SHUTDOWN_ERR

3-Error

Error in [chars] : [chars]

Internal error

mcast-vpn

LOG_STD_RECUR_ACTION

MDT-4-TDB_WALK_ERR

4-Warning

Error Walking list of TDB's

Walk of all pim tdb's associated with a given pim pdb cannot be completed

-

LOG_STD_NO_ACTION

MROUTE-6-MVRF_NOTEXISTS

6-Information

MRT[dec] MVRF does not exist

-

-

-

MROUTE-2-RADIXINIT

2-Critical

Error initializing IP multicast radix for [inet]

Insufficient memory is available to initialize the IP multicast\n\ routing table.

-

LOG_STD_SH_TECH_ACTION

MROUTE-4-RADIXDELETE

4-Warning

Error trying to delete multicast route entry [inet]/[dec] for [inet] expected [hex] got [hex]

An error in the multicast routing table occurred. A route could not be\n\ deleted from the routing table.

-

"Execute a clear ip mroute command. Determine whether the router is low\n\ on memory. " LOG_STD_RECUR_ACTION

MROUTE-4-SNMP_RADIX_ERR

4-Warning

Failed to [chars] snmp node [chars] snmp radix tree for multicast group * [inet].

An error occured while adding or deleting snmp node in snmp \n\ radix tree when mroute is created or deleted.

-

"An error in adding or deleting snmp node in snmp radix tree \n\ occurred." LOG_STD_ACTION

MROUTE-4-MTU_MISMATCH

4-Warning

WARNING: With IP multicast enabled interfaces which transmit traffic from larger to smaller MTU interfaces may not be hardware switched due to fragmentation. A degradation in performance may occur.

WARNING: With IP multicast enabled interfaces which transmit traffic\n\ from larger to smaller MTU interfaces may not be hardware switched due\n\ to fragmentation. A degradation in performance may occur.

-

"Set MTU values on all interfaces to be identical. "

MROUTE-3-WAVLINIT

3-Error

Could not initialize WAVL tree for [inet][inet]

When the WAVL tree can not be initialized we can't search for midbs\n\ so there is no reason to keep the mdb around.

-

"An error in initializing the multicast routing occurred." LOG_STD_ACTION

MROUTE-4-REGISTER_SOURCE_CONFIG

4-Warning

Removing pim register source configuration for [chars]

The register source interface was deleted had its IP address removed or its vrf forwarding changed.

-

"No action required just check 'ip pim register-source' configuration." LOG_STD_ACTION

MROUTE-6-LARGE_TWHEEL_DELAY

6-Information

Exceeded maximum delay [dec] ms requested: [dec]

Because of the way the timer wheel works there is a maximum delay defined. If we try to schedule a function with a higher delay we still schedule it using the maximum delay possible minus a small delay offset.

-

"A timer with large delay was requested. Check if a large igmp query-interval" " is set. Some timers may refresh periodically to allow for the large delay.\n\" LOG_STD_NO_ACTION

MROUTE-3-TWHEEL_DELAY_ERR

3-Error

Exceeded maximum delay [dec] ms requested: [dec]

Because of the way the timer wheel works there is a maximum delay defined. If we try to schedule a function with a higher delay we still schedule it using the maximum delay possible

-

"An error in maintaining the timer wheel occurred." LOG_STD_ACTION

MROUTE-3-TWHEEL_INSERT_ERR

3-Error

An error occured after inserting or executing a timer wheel event

An error occured after inserting or executing a timer wheel event

-

"An error in maintaining the timer wheel occurred." LOG_STD_ACTION

MROUTE-3-TWHEEL_SLOT_ERR

3-Error

Timer wheel event:[hec] slot:[dec] func:[hec] unequal to exec slot: [dec]

Timer wheel event has inconsistent slot number

-

"Clear ip mroute *" LOG_STD_ACTION

MROUTE-3-TWHEEL_INT_ERR

3-Error

Timer wheel error at interrupt level [dec]

Timer wheel internal error

-

"An error in maintaining the timer wheel occurred." LOG_STD_ACTION

MROUTE-3-TWHEEL_INIT_ERR

3-Error

Trying to re-initialize an already initialized timer wheel

An error occured intializing a timer twheel

-

"An error in maintaining the timer wheel occurred." LOG_STD_ACTION

MROUTE-3-TWHEEL_ERR

3-Error

Timer wheel internal error

Timer wheel internal error

-

"An error in maintaining the timer wheel occurred." LOG_STD_ACTION

MROUTE-3-MIDB_QUEUE_ERR

3-Error

Interface [chars] not in [inet] [inet]

This is an error condition. The midb has the highest expiration timer but is not in the mdb->midb

-

"An error in maintaining the multicast route table occurred." LOG_STD_ACTION

MROUTE-4-RADIXINSERT

4-Warning

Error trying to add multicast route entry [inet]/[dec] for [inet] expected [hex] got [hex]

An error in the multicast routing table occurred. A route could not be\n\ inserted in to the routing table.

-

"Execute a clear ip mroute command. Determine whether the router is low\n\ on memory. " LOG_STD_RECUR_ACTION

MROUTE-4-ROUTELIMIT

4-Warning

Current count of [dec] exceeds multicast route-limit of [dec]

The number of multicast routes equals the configured maximum allowed.\n\ New routes cannot be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried\n\ by this router then use the 'ip multicast route-limit' command to\n\ increase the number of multicast routes.\n\ Otherwise no action is required."

MROUTE-4-ROUTELIMIT_ATTEMPT

4-Warning

Attempt to exceed multicast route-limit of [dec]

The number of multicast routes equals the configured maximum allowed.\n\ New routes cannot be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried\n\ by this router then use the 'ip multicast route-limit' command to\n\ increase the number of multicast routes.\n\ Otherwise no action is required."

MROUTE-4-ROUTELIMITWARNING

4-Warning

multicast route-limit warning curr [dec] threshold [dec]

-

-

-

MROUTE-4-MROUTELIMIT

4-Warning

Exceeded multicast limit for group [inet] source [inet] on interface [chars]

The allowed number of multicast routes having the incoming or outgoing\n\ interface reached the limit specified by a configured access-list.\n\ New routes cannot be added unless the interface configuration is changed.

-

"If multicast traffic over the interface is of any priority\n\ among the traffic carried by this router then use the 'ip multicast limit'\n\ interface command to increase the number of multicast routes.\n\ Otherwise no action is required.\n\ Use 'debug ip mroute limit' and/or 'show ip multicast limit'\n\ to find exactly which multicast interface limit was exceeded."

MROUTE-3-ROUTECOUNT_ZERO

3-Error

Multicast route count reached zero

The running count of multicast routes reached zero when it \n\ should be non-zero.

-

"An error in maintaining the multicast route count occurred." LOG_STD_ACTION

MROUTE-3-NO_PIM_NBR

3-Error

There is no PIM neighbor on this IDB: [chars]

Probably PIM is not configured correctly on this interface or on interfaces of the nexthop routers.

-

"Check PIM configurations on local and neighbor routers." LOG_STD_ACTION

MROUTE-3-RECUR_ROUTE_DEPTH_ERR

3-Error

Recursive route lookup has reached its max depth for: [inet]

Recursive route lookup has a pre-defined depth limit and it has been reached.

-

"If possible reduce rounds of next hop lookup needed for the network address in question." LOG_STD_ACTION

MROUTE-3-IGMP_NOT_FOUND

3-Error

IGMP group [inet] to delete from interface [chars] not found

The group to be deleted from the interface could not be found in the\n\ IGMP cache.

-

"An inconsistency in maintaining the IGMP cache occurred." LOG_STD_ACTION

MROUTE-3-IGMP_WAVL_ERROR

3-Error

IGMP wavl [chars] failed for group [inet] in interface [chars]

The addition/deletion of igmp group in wavl tree failed.

igmp

"Collect 'show tech ipmulticast' output." LOG_STD_ACTION

MROUTE-4-INCONSISTENT_IDB_TABLEID

4-Warning

PIM detected inconsistency in table-id information on [chars].

PIM detected that the interface tableid is not the same as the value\n\ maintained by the multicast code

mcast-vpn

"LOG_STD_ACTION"

MROUTE-3-IGMP_TWHEEL_INIT_ERR

3-Error

Error trying to initialize the IGMP timer wheel

An error occured intializing a timer twheel

-

"An error in maintaining the timer wheel occurred." LOG_STD_ACTION

MROUTE-4-IPMC_INVALID_SB

4-Warning

Unexpected access to IP Multicast interface subblock field

IOS attempts to access the value of an IP Multicast interface field\n\ whose interface subblock is not yet created.

-

"An inconsistency accessing an IP Multicast interface subblock occurred." LOG_STD_ACTION

MROUTE-3-IGMP_LATE_PROCESS_ERR

3-Error

IGMP process is not up yet

An error occured accessing IGMP process watched queue

ipmulticast

"An error in accessing IGMP process watched queue." LOG_STD_ACTION

MROUTE-3-NOT_IN_MDB_OR_GDB_CACHE

3-Error

*G or SG being deleted for group [inet] does not exist in the

An error occured due to which the gdb or mdb being deleted does not \n\ exist in it's respective cache

-

"An error has occurred in maintaining mdb." LOG_STD_ACTION

COMP_API-4-COMP_API_IDB_WARNING

4-Warning

Incorrect External interface field access API invocation

A routine external to the IP Multicast Component accesses an\n\ interface field with invalid interface argument

-

"An inconsistency calling an IP Multicast interface access API occurred." LOG_STD_ACTION

MSDP-5-PEER_UPDOWN

5-Notice

Session to peer [inet] going [chars]

Session to peer going up or down

-

"Determine whether the router is low on memory."

MSDP-4-PKT_TOO_BIG

4-Warning

Message size violation on [dec]-byte packet from [inet] discarded

A message larger than the maximum MSDP message size was received. \n\ There is also a possibilty that this is an internal error.

-

"show version"

MSDP-5-PEER_IS_SELF

5-Notice

Peering with self [inet]

-

-

-

MSDP-4-SA_LIMIT

4-Warning

SA from peer [inet] RP [inet] for [inet] [inet] exceeded sa-limit of [dec]

-

-

-

IGMP-3-IGMP_CLIENT_ID_ERR

3-Error

Invalid Client Id usage [dec].

Invalid Client Id usage

-

"Check the Client Id" LOG_STD_NO_ACTION

IGMP-6-IGMP_GROUP_LIMIT

6-Information

IGMP limit exceeded for group * [inet] on [chars] by host [inet]

-

-

-

IGMP-6-IGMP_CHANNEL_LIMIT

6-Information

IGMP limit exceeded for channel [inet] [inet] on [chars] by host [inet]

-

-

-

IGMP-3-QUERY_INT_MISMATCH

3-Error

Received a non-matching query interval [dec] from querier address [inet]

Mismatch of IGMP version found between routers.

-

"Configure both the interfaces with same IGMP version." LOG_STD_ACTION

IGMP -3-DNS_ERROR

3-Error

DNS lookup time out. DNS lookup for ssm mapping will be disabled for 60 sec.

DNS source lookup time out. DNS server did not respond \n\ to the DNS query this may be due to DNS server is down. \n\ DNS lookup will be stopped for next 60 sec.

-

"Disable DNS lookup for ssm mapping till the DNS " "server comes up." LOG_STD_ACTION

IGMP-3-NO_DNS_SERVER

3-Error

No DNS server is configured. \nDNS-based SSM mapping should be disabled if no DNS server is configured.

There is no DNS server present. Processing IGMP \n\ packets may be delayed if the DNS-lookup is done continuosly.

-

"Disable DNS-based SSM mapping if there is \n\ no DNS-server present in the network." LOG_STD_ACTION

IGMP-4-NO_INPUT

4-Warning

IGMP packet without input interface received from [inet] for [inet]

An unexpected IGMP packet without input interface was received.

ipmulticast

"Consider taking note of source and destination present in syslog." LOG_STD_ACTION

IGMP-4-MROUTE_IC_FLAG

4-Warning

While adding or deleting multicast state some state may not correctly have local interest flag set or cleared.

Repeated attempts to adjust local interest flag were running over time and some state may not have been adjusted.

-

LOG_STD_SH_TECH_ACTION

IGMP-3-IGMP_LIST_RESET_SOURCE_FLAGS

3-Error

Failed to reset source flags for [inet].

Repeated attempts to reset the flags failed.

mcast-igmp

LOG_STD_ACTION

IGMP-3-IGMP_LIST_DEL_STATIC

3-Error

Failed to delete static groups for interface [chars].

Repeated attempts to walk the list failed.

mcast-igmp

LOG_STD_ACTION

RPF-4-RADIXINIT

4-Warning

Error initializing the MVRF select radix tree

An internal software error occurred.

mcast-vpn

LOG_STD_SH_TECH_ACTION

RPF-4-RADIXINSERT

4-Warning

Error inserting a new entry into the MVRF select radix tree

An internal software error occurred.

mcast-vpn

LOG_STD_SH_TECH_ACTION

IPMCAST_RPF-3-INTERNAL_ERROR

3-Error

An internal error has occured while obtaining RPF information [chars]

RPF handling Internal error

ipmulticast

LOG_STD_RECUR_ACTION

IPMCAST_RPF-4-RPF_LOOKUP_LOOP

4-Warning

RPF route lookup loop for [inet]

A routing loop occurred during the recursive resolution of an RPF address

ipmulticast

"Check routing tables used for RPF"

IPMCAST_RPF-4-FOREIGN_VRF

4-Warning

RPF for [inet] VRF [chars] resolves in a foreign VRF [chars]

-

-

-

MCAST_MQC-3-CMAP_SDB_REGISTER

3-Error

Error initialising class-map of type multicast-flows.

Could not register the component related to the class-map of type \n\ multicast-flows to the string database.

ipmulticast

"LOG_STD_ACTION"

MROUTE-2-TOPO_WAVLINIT

2-Critical

Error initializing IP multicast wavl handler for [inet]

Insufficient memory is available to initialize the IP multicast\n\ multi-topology routing table.

-

LOG_STD_SH_TECH_ACTION

IPMCAST_LIB-4-UNEXPECTED_CONDITION

4-Warning

Unexpected condition: [chars]

An un expected condition situation state or event has been detected.

ipmulticast

LOG_STD_NO_ACTION

IPMCAST_LIB-4-UNKNOWN_EVENT_ERR

4-Warning

Unexpected event received: [dec]

No handler found for event

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB-3-TIMER_ERR

3-Error

Unexpected error in the timer library: [chars]

Internal error

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB-6-EVENT_Q_SIZE

6-Information

The event queue size has exceeded [dec]

Processing may become slower

ipmulticast

LOG_STD_NO_ACTION

IPMCAST_LIB-6-TIMER_BUSY

6-Information

Timer drift is accumulating [dec] msecs

There is large amount of processin load and the timers are accumulating delay.

ipmulticast

LOG_STD_RECUR_ACTION

IPMCAST_LIB-3-MEMORY_ERR

3-Error

Not enough memory. [chars]

Memory not available for allocating requested object.

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB-3-VRF_CTX_ERR

3-Error

[chars] Ctx: 0x[hec]

Failure in updating the LIB VRF Context structures.

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB-4-IPMCAST_LIMIT_THRESHOLD

4-Warning

[chars] interface '[chars]' for [chars][chars] [chars] %lld

The maximum number of times the given interface appears as incoming or outgoing for some multicast state has reached threshold of its configured limit.

ipmulticast

"The configured multicast limit for some interface" " has reached the threshold of its configured mCAC" " limit. Please take proactive measures at this point" " like increasing the mCAC limit."

IPMCAST_LIB-4-IPMCAST_LIMIT

4-Warning

Adding [chars] interface '[chars]' denied for [chars][chars]

The maximum number of times the given interface appears as incoming or outgoing for some multicast state is reached.

ipmulticast

LOG_STD_NO_ACTION

IPMCAST_LIB-3-IPMCAST_LIMIT_SYNC

3-Error

Failed to sync multicast limit state to the standby RP

An internal failure prevented sending of multicast limit information to the standby RP. Some multicast traffic disruption is possible following a route processor failover.

ipmulticast

LOG_STD_NO_ACTION

IPMCAST_LIB_RPF-3-RW_START_FAIL

3-Error

Error trying to start RPF route watch for prefix [chars] in table [dec] [chars] RPF information will not be obtained

-

-

-

IPMCAST_LIB_RPF-4-RTMGR_TOPO_ERR

4-Warning

Unexpected error accessing topology specific information

An internal error has occured while accessing topology specific information. The RPF information may not be obtained resulting in problems with multicast flows

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_RPF-3-INTERNAL_ERROR

3-Error

An internal error has occured while obtaining RPF information [chars]

RPF handling Internal error

ipmulticast

LOG_STD_RECUR_ACTION

IPMCAST_LIB_RPF-3-STOP_FAIL

3-Error

Error trying to stop RPF watch for a prefix

Internal error has occured while trying to stop obtaining RPF change information

ipmulticast

LOG_STD_RECUR_ACTION

IPMCAST_LIB_RPF-4-RIB_UNREGISTER_FAIL

4-Warning

Multicast failed to unregister with RIB

Multicast could not unregister with RIB when multicast is disabled. There will not be any existing traffic flow since multicast is already disabled. However if enabled again and if problem is seen with multicast traffic flow it should be reported

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_RPF-3-RIB_REGISTER_FAIL

3-Error

Failed to register with RIB multicast RPF lookups will not function

Multicast could not register with RIB to obtain RPF information later. This will cause severe problem when there is multicast traffic flow since it will not be possible to obtain RPF information

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_RPF-3-INVALID_RW_CONTEXT

3-Error

Invalid context specified for a multicast route watch client.

An invalid context was specified for handling a multicast route watch update. Multicast traffic flow may be degraded by failure to correctly determine RPF state information.

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_RPF-3-DUPLICATE_RW_CONTEXT

3-Error

Specified multicast route watch client registration context is already in use.

The context specified for a multicast route watch client registration request is already in use. The client registration request can not be processed. Multicast traffic flow may be degraded by failure to correctly determine RPF state information.

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_RPF-3-RW_INIT_FAIL

3-Error

Failed to START/STOP Route-watch debugging for '[chars]'

Multicast could not START or STOP Route-watch debugging for the specific Address-family IPv4/IPv6 listed.

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_GIR-3-MCAST_GIR_CLIENT_NOT_FOUND

3-Error

Failed to find multicast GIR client for vrf [chars]

Failed to find multicast GIR client

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_STR-3-MCAST_STRING_COPY_ERROR

3-Error

Multicast string copy failure

Multicast string copy failure

ipmulticast

LOG_STD_ACTION

IPMCAST_LIB_STR-4-MCAST_STRING_COPY_BUF_OVERFLOW

4-Warning

Multicast string copy overflow

Multicast string copy overflow

ipmulticast

LOG_STD_ACTION

MIC-3-INVALID_CLIENT_TYPE

3-Error

Caller specified invalid MIC client type [dec].

The MIC client type is out of range.

-

LOG_STD_NO_ACTION

MIC-2-RF_REG_FAIL

2-Critical

Failed to register with RF status [dec].

The MIC failed to register with RF.

-

LOG_STD_NO_ACTION

MRIB-3-GENINITFAIL

3-Error

Initialization failed: [chars] [chars]

An unrecoverable error occurred at system initialization time.

ipmulticast

LOG_STD_ACTION

MRIB-3-GENCOMMERR

3-Error

Communication error: [chars] [chars] in [chars]

A Inter Process Communication error occurred.

ipmulticast

LOG_STD_ACTION

MRIB-2-NOMEMORY

2-Critical

No memory for [chars] in [chars]

The requested operation could not be accomplished because of a low\n\ memory condition.

ipmulticast

LOG_STD_REDUCE_ACTION

MRIB-3-REDUCEDFUNCT

3-Error

Initialization of \[chars]\ functionality failed

The initialization of a functionality failed. This component might\n\ still operate without the functionality.

ipmulticast

LOG_STD_REDUCE_ACTION

MRIB-3-INTERNALERR

3-Error

Internal error: [chars] in [chars] line [dec] [chars]

An internal software error occurred.

ipmulticast

LOG_STD_ACTION

MRIB-4-FILTRVIOLERR

4-Warning

Filter violation error: conn [dec] [chars]:[chars] in [chars]

A client tried to modify a route attribute not owned by it.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB-4-INCORRECTPARS

4-Warning

Illegal parameter in function call [chars] in [chars]

An externally accessible function has been called with illegal\n\ parameters. the parameters has been casted to an acceptable value.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB-4-NOMEMORYW

4-Warning

No memory for [chars] in [chars]. Handling: [chars]

The requested operation could not be accomplished because of a low\n\ memory condition but the problem has ben handled locally.

ipmulticast

LOG_STD_REDUCE_ACTION

MRIB-4-DEBUGERR

4-Warning

Debugging error: [chars] in [chars] line [dec] [chars]

An error related to the debugging subsystem occurred.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB-3-MESG_NOMEM_FATAL

3-Error

Allocation of memory failed for an incoming message

Allocation of memory failed during the processing of an incoming message. This failure my have unpredictable results.

-

LOG_STD_REDUCE_ACTION

MRIB-3-BNDL_NOMEM_FATAL

3-Error

Update-Set fatal allocation error [chars]

Allocation of memory failed during the processing of an Update-Set. This failure my result in database inconsistency.

-

LOG_STD_REDUCE_ACTION

MRIB-4-BNDL_NOMEM

4-Warning

Update-Set allocation error [chars]

Allocation of memory failed during the processing of an Update-Set. This failure my result in inefficient processing of route-updates.

ipmulticast

LOG_STD_REDUCE_ACTION

MRIB-4-BNDL_MSG

4-Warning

Update-Set invalid message [chars]

An invalid message was received during the processing of an Update-Set.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB-4-BNDL_ID_INUSE

4-Warning

An old Update-Set ID is still in use [hec]

While allocating Update-Set IDs the MRIB found an old ID still in use. This could be due to a programming error.

ipmulticast

LOG_STD_SH_TECH_ACTION

PGM-3-RTX_STATE_ALLOC_ERR

3-Error

Failed to allocate [chars] state

Resources memory for retransmit state are exhausted\n\msgdef_recommended_action Manually clear all retransmit state

-

-

PGM-3-RTX_STATE_FREE_ERR

3-Error

Failed to free [chars] state

Resources memory for retransmit state are not serviceable.

ipmulticast

-

PGM-3-EXP_TSI_SQN_ERR

3-Error

Expiring TSI [chars] has retransmit state

An expiring PGM TSI has unexpired retransmit state. This can only\n\ occur due to an internal error or due to unfreeable memory.

ipmulticast

LOG_STD_REDUCE_ACTION LOG_STD_RECUR_ACTION

PGM-3-PAK_ALLOC_ERR

3-Error

Failed to allocate buffer for [chars]

-

-

LOG_STD_REDUCE_ACTION

PGM-6-ADDR_ERR

6-Information

Invalid [chars] address [inet] in [chars]

Received the packet with invalid address.

-

LOG_STD_NO_ACTION

PGM-6-PAK_MALFORMED_ERR

6-Information

Malformed packet: [chars]

A PGM packet did not pass the internal sanity check.

-

LOG_STD_NO_ACTION

PGM-6-PAK_IIF_FIXUP

6-Information

Pak for [inet] received on [inet] fixed input interface

A PGM packet was recieved on an interface other than the one it was\n\ addressed to.

-

LOG_STD_NO_ACTION

PGM-6-TSI_GROUP_CHANGE

6-Information

TSI group changed from [inet] to [inet]

A PGM SPM advertising a new group for the TSI was processed.

-

LOG_STD_NO_ACTION

PGM-6-TSI_SOURCE_CHANGE

6-Information

TSI source changed from [inet] to [inet]

A PGM SPM advertising a new source for the TSI was processed.

-

LOG_STD_NO_ACTION

PGM-6-QUEUE_FULL

6-Information

Serviced full queue of PGM packets.

The PGM process is busy either because of excessive retransmit\n\ state or because of excessive traffic.

-

LOG_STD_REDUCE_ACTION

MRIB_PROXY-3-MRIB_LC_FAILED_IPC_OPEN

3-Error

LC in slot [dec] failed to open IPC port to RP error = [chars]. Verify MRIB updates are being distributed to this LC.

The linecard has failed to open IPC port towards the Route Processor

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-3-MRIB_LC_FAILED_SEND_LC_READY

3-Error

LC in slot [dec] failed to send LC ready to RP error = [chars]. Verify MRIB updates are being distributed to this LC.

The linecard has failed to send Ready message to the Route Processor

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_RP_FAILED_IPC_CREATE

2-Critical

RP failed in creating IPC port error = [chars]

The Route Processor failed to create MFIB Interprocess Communications port

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_FAILED_GET_IPC

2-Critical

LC failed allocating IPC buffer which may lead to data loss or inconsistent MFIB states slot = [dec]

The Linecard has failed in allocating interprocessor communication buffer.

ipmulticast

LOG_STD_REDUCE_ACTION

MRIB_PROXY-3-MRIB_LC_READY_NOIPC

3-Error

LC in slot [dec] failed allocating IPC buffer to send LC ready Verify MRIB updates are being distributed to this LC.

The Linecard has failed in allocating interprocessor communication buffer to send the ready message.

ipmulticast

LOG_STD_REDUCE_ACTION

MRIB_PROXY-2-MRIB_RP_FAILED_LC_PORT_INFO

2-Critical

RP failed in creating linecard port info for distributed mode slot = [dec]

The Route Processor has failed in creating linecard port info for distributed mode

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-3-MRIB_RP_FAILED_LC_PORT_OPEN

3-Error

RP failed in opening linecard port info for distributed mode slot = [dec]. Verify MRIB updates are being distributed to this LC.

The Route Processor has failed in opening linecard port info for distributed mode

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_FAILED_IDB_MAP

2-Critical

LC failed in mapping interface number [dec]

The linecard failed in mapping an interface from the global representation to the local one

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_RP_FAILED_IDB_MAP

2-Critical

RP failed in mapping interface

The route processor failed in mapping an interface from the global representation to the local one or vice-versa

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_RP_FAILED_GET_IPC

2-Critical

RP failed allocating IPC buffer which may lead to data loss or inconsistent MFIB states

The Route Processor has failed in allocating interprocessor communication buffer.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_UPDATE_IGNORED

2-Critical

LC in slot [dec] ignored one or more mroute updates

The linecard ignored one or more mroute updates because the buffer containing them failed a sanity check. The linecard MFIB state may now be inconsistent.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_FETCH_FAIL

2-Critical

LC in slot [dec] failed to send an RPC fetch request to the RP: [chars]

The linecard attempted to read mroute updates from the route processor but the RPC request failed. The linecard MFIB state may now be inconsistent or frozen.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_RP_CREPRC_FAILED

2-Critical

The Route Processor failed to create a required process.

The Route Processor could not create the MRIB RP proxy process. Distributed multicast will not be started on this system.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-3-MRIB_LC_CREPRC_FAILED

3-Error

LC in slot [dec] failed to create a required process. Verify MRIB updates are being distributed to this LC.

The linecard could not create a process to perform delayed IPC initialization. The MFIB will not be started on this linecard.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_FAILED_NO_TABLE_NAME

2-Critical

LC in slot [dec] failed to connect to RP due to missing table name.

The linecard could not instigate a connection to the RP for this instance as it was not supplied a table name.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_NOT_OPENED

2-Critical

LC in slot [dec] attempted to contact the RP without having opened the connection first

The linecard called an MRIB API that required the connection with the MRIB in the RP to be opened but no connection had been established.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_INTERNAL

2-Critical

The unrecoverable error \[chars]\ occurred in the MRIB-IPC subsystem.

An unrecoverable error occurred restart the MRIB subsystem.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_IO_CLOSE_PENDING_WRITE

2-Critical

LC CCB : \[chars]\ close deferred

MRIB LC connection to MFIB close attempted while MRIB update write in progress connection close deferred.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_PROXY-2-MRIB_LC_IO_CLOSE_PENDING_FETCH

2-Critical

LC CCB : \[chars]\ close deferred

MRIB LC connection to MFIB close attempted while MRIB update fetch in progress connection close deferred.

ipmulticast

LOG_STD_SH_TECH_ACTION

MRIB_API-3-REG_FAIL

3-Error

Server unexpected error: [chars]

An internal error occurred in a registry call from the MRIB API

ipmulticast

LOG_STD_ACTION

MRIB_API-3-CORRPT

3-Error

Corrupted update: [chars]

A corrupted update was received form the MRIB by the MRIB API

ipmulticast

LOG_STD_ACTION

MRIB_API-3-ASYNC_ERR

3-Error

Asynchronous error: [chars]. errno 0x[hec]

An unhandled asynchromous error occurred in the MRIB API

ipmulticast

LOG_STD_ACTION

MRIB_API-7-ASYNC_WAR

7-Debug

Warning: [chars]

A recoverable error condition occurred in the MRIB API

ipmulticast

LOG_STD_NO_ACTION

MCASTRED-3-INITNOQUEUE

3-Error

Failed to create [chars] watched queue during multicast redundancy initialization

An attempt to create a watched queue during multicast PIM

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-INITNOBOOL

3-Error

Failed to create [chars] watched boolean during multicast redundancy initialization

An attempt to create a watched boolean during multicast PIM

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-TUNSYNCXMIT

3-Error

Failed to transmit sync MDT tunnel information for mvrf [chars] to the standby RP.

An IPC transmission attempt has failed to send an IPC message to provide the standby RP with MDT tunnel sync information required for creation of the MDT tunnel on the standby RP.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-TUNSYNCRCV

3-Error

[chars] failure in reception of MDT tunnel sync information for mvrf [chars] on the standby RP.

Confirmation has failed for standby RP reception of an MDT tunnel message. This message is needed to provide the standby RP with MDT tunnel sync information required for creation of the MDT tunnel on the standby RP.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-TUNSYNCMSG

3-Error

Received invalid termination message for mvrf[dec] while

Confirmation has failed for standby RP reception of an MDT tunnel message. This message is needed to provide the standby RP with MDT tunnel sync information required for creation of the MDT tunnel on the standby RP.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-TUNSYNCTIME

3-Error

Timeout waiting for confirmation of mdt tunnel sync for mvrf[dec] [chars]

-

-

-

MCASTRED-3-RCVNODATA

3-Error

No data pointer returned for received checkpoint message

On reception of a checkpoint message at the standby RP an attempt to obtain the location of the data for the message returned a NULL pointer. No message contents are available for this message.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-SNDNODATA

3-Error

No data pointer provided in checkpoint message to be sent.

After allocation of a checkpoint message buffer in the primary RP an attempt to obtain the location of the data for the message returned a NULL pointer. The message can not be sent. Loss of standby sync is likely.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MSGSEQNUM

3-Error

Out of order sequence number in received sync message for sync data type [dec] received epoch/seq [dec]/[dec] expected [dec]/[dec]

The sequence number specified in a sync message received by the standby RP is not the expected sequence number for the next received sync message. Some sync messages may have been lost.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-DECODEFUNC

3-Error

No decode function exists for sync data type [dec]

There is no function defined for handling sync data of the specified type. No sync action is possible on the standby RP for the sync message that specified this data type.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-INVSYNCTYP

3-Error

Attempt to initiate sync request for invalid sync type

The sync data type specified by the function attempting to initiate a sync operation is not a valid type. No sync operation can be performed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MDT_DATA_RCV_DECAP_INV_OP

3-Error

Invalid operation type [dec] specified for an MDT data receive decap message.

The sync operation type specified in a message to sync MDT data group receive decapsulation information was not a defined type for this message. The requested action can not be performed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MDT_NO_MDB

3-Error

Failed to find or create an MDB during MDT data send group [chars] sync for group [inet] source [inet] MVRF [chars]

The standby RP could not create the MDB required for building an MDT data group send entry. Interruption of MVPN data flow is possible if an RP failover occurs.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MDT_NO_SND_GRP

3-Error

Failed to create an MDT send group entry during MDT data send group sync for group [inet] source [inet] MVRF [chars]

The standby RP could not create the specified MDT data group send entry. Interruption of MVPN data flow is possible if an RP failover occurs.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ALCSYNCTYP

3-Error

Attempt to allocate sync request for invalid sync type [dec]

The sync data type specified by the function attempting to perform a sync operation is not a valid type. No sync operation can be performed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DELNULLREQ

3-Error

No sync request specified in sync request deletion attempt.

In a call to delete a sync request entry the caller failed to specify the location of the sync request to be deleted. A memory leak is likely.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DELSYNCTYP

3-Error

Attempt to delete sync request for invalid sync type [dec]

The sync data type specified by the function attempting to delete a sync request is not a valid type. The sync request can not be deleted. A memory leak is likely.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HASHNQ

3-Error

Failed attempt to enqueue sync request type [dec] in hash table

An attempt to link a new sync request into the sync request hash table failed. This indicates corruption of the linkage within the hash table. The sync operation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-SYNC_REQ_ORPHAN

3-Error

Orphaned queue links found in sync request hash table search for sync type [dec]

An attempt to find a matching entry for a new sync request in the sync request hash table failed because of corruption of the linkage within the hash table. The sync operation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-WAITQ_ORPHAN

3-Error

Orphaned queue links found in the [hec] MVRF wait queue.

An attempt to perform state transition handling for MVRFs in this queue failed because of queue corruption or because one or more queue link entries did not specify the address of the corresponding MVRF. Multicast route convergence following an RP failover may be delayed or impaired.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BLKNOBOOL

3-Error

Failed to create [chars] watched boolean for bulk sync

An attempt to create a watched boolean to monitor bulk sync of state information to the standby RP has failed. It is not possible to verify successful completion of the bulk sync operation.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BLKNOFUNC

3-Error

No bulk sync function defined for sync type [dec]

There is no function defined for bulk synching of database information of this type. It is possible that some required information may not be synched to the standby RP.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BULKRQTIME

3-Error

Timeout sending bulk sync requests to standby

The maximum wait time has expired for transmission of enqueued bulk sync messages to the standby RP. It is possible that not all required sync messages have been successfully sent.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BULK_COMPLETE_INCOMPATIBLE

3-Error

Skipping sending of bulk sync completion message to peer: Incompatible message type.

The message code designated for peer RP confirmation of bulk sync completion was not recognized by the ISSU infrastructure as a compatible PIM HA message type. Although PIM bulk sync may have succeeded bulk sync confirmation is not possible.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BULK_COMPLETE_XFORM_FAIL

3-Error

ISSU xmit transform failed for bulk send complete message.

ISSU transformation failed on the message used for peer RP confirmation of bulk sync completion. Although PIM bulk sync may have succeeded bulk sync confirmation is not possible.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-RTRYNOREQ

3-Error

Sync retry requested with no sync request specified

Retry for transmission of a sync message was requested but no sync request information was specified. The retry can not be executed. The standby RP may no longer be synchronized with the active RP.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-RTRYLIMIT

3-Error

Retry limit reached for sync type [dec]

The maximum allowable number or transmission retries has failed for a database entity of this type. The retry can not be executed. The standby RP may no longer be synchronized with the active RP.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-EOXNOREQ

3-Error

End of sync message transmission: no sync request specified

End of sync message transmission handling was invoked with no sync request specified. Cleanup for successful transmission can not proceed. Retry for unsuccessful transmission can not proceed. Memory leakage is likely and loss of sync on the standby RP is possible.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ACKUNQMSG

3-Error

Failed to remove sync request type [dec] from pending ACK queue

An attempt failed to unlink a completed sync request from the queue for requests awaiting confirmation of receipt from the standby RP. This indicates corruption of the linkage within the pending acknowledgement queue. False timeout error messages and memory leakage are likely. Loss of standby RP sync is possible.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-EOXBADRC

3-Error

Invalid completion code [dec] for sync message transmission type [dec]

An undefined completion code was specified for end of sync message transmission handling. Memory leakage false timeouts and other subsequent errors may result.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MSGNOREQ

3-Error

Could not find sync request for completed sync message type [dec]

The sync request corresponding to a completed sync message could not be determined. Memory leakage false timeouts and other subsequent errors may result.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MSGHDL

3-Error

Could not obtain sync handle for completed sync message type [dec] [dec]

-

-

-

MCASTRED-3-ALLOCMSG

3-Error

Sync message buffer allocation failed for sync info type [dec]

An attempt to allocate a buffer for sync message transmission failed. Loss of sync on the standby RP is likely.

-

LOG_STD_SH_TECH_ACTION " Attempt standby RP synchronization by reloading " "the standby RP. "

MCASTRED-3-FMTFUNC

3-Error

No sync message format function defined for sync type [dec]

No function is defined to create a sync messages for this type of database information. Loss of sync on the standby RP is likely.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-FMTMSG

3-Error

Failed to format a sync message for sync type [dec]

An attempt to format create a sync message has failed. The

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-SNDMSG

3-Error

Failed to send a sync message for sync type [dec]

An attempt to send a sync message has failed. The message transmission will be automatically retried.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ACKQMSG

3-Error

Failed attempt to enqueue sync message type [dec] in confirmation queue

An attempt to link a new sync message into the sync message confirmation queue failed. This indicates corruption of the linkage within the queue. It is not possible to track message confirmation or to initiate a recovery action if confirmation is not received.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-FINDNULLENT

3-Error

No target specified for sync entity search.

In a call to invoke a search for a database entity requiring synching to the standby RP the caller failed to specify a descriptor for the entity to be synched. The sync operation entity can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-LOCNULLENT

3-Error

No destination specified in search for sync entity of type [dec]

A function was invoked to search for a database entity of the specified type. The caller failed to specify a destination for storing the search result. The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-LOCNULLHND

3-Error

No search handle specified in search for sync entity of type [dec]

A function was invoked to search for a database entity of the specified type. The caller failed to specify a search handle key

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-SEARCH_LOGIC

3-Error

Conflicting results for database search during a sync operation for sync type [dec]

The function invoked to search for a database entity of the specified type provided a search return code that is inconsistent with the information returned by the search. Information that should be available was not provided. The sync operation

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLP_NULL_REG

3-Error

NULL list registered for PIM sync helper functions.

In a request to register helper functions for the owner of one or more PIM sync databases a NULL value was specified for the list of functions to be registered. PIM sync operations may be inhibited for the affected database types.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLP_NULL_PRM

3-Error

NULL parameter specified for [chars] PIM sync helper registration.

The PIM sync infrastructure specified one or more NULL pointers to the output parameters in a call to a pim sync helper registration function. No PIM sync helper functions can be registered for this address family. As a result no PIM SSO functionality can be provided for this address family.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLP_BAD_TYPE

3-Error

Invalid helper type [dec] specified for [chars] PIM sync helper registration.

The PIM sync infrastructure specified an invalid helper type in a call to a pim sync helper registration function. No PIM sync helper functions can be registered for this helper type for this address family. As a result PIM SSO functionality will be impaired for this address family.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLP_REG_COUNT

3-Error

Invalid count [dec] specified for PIM sync helper registration.

In a request to register helper functions for the owner of one or more PIM sync databases an invalid value was specified for the count of functions to be registered. PIM sync operations may be inhibited for the affected database types.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLP_REG_TYPE

3-Error

Invalid type [dec] specified for PIM sync helper registration.

In a request to register helper functions for the owner of one or more PIM sync databases an invalid value was specified for the helper function type of the functions to be registered. PIM sync operations may be inhibited for the affected database types.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLP_REG_SYNC_TYPE

3-Error

Invalid sync type [dec] specified for PIM sync helper registration.

In a request to register helper functions for the owner of one or more PIM sync databases an invalid value was specified for the sync database type of at least one of the functions to be registered. PIM sync operations may be inhibited for the affected database types.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-AF_NULL_PRM

3-Error

NULL parameter specified for setting PIM HA address family [dec] context.

A function handling a PIM NSF state machine transition specified an invalid NULL address for one or more pointers to PIM NSF

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-FMTGENNOBF

3-Error

No message buffer specified for generic sync message info

A function was invoked to store generic sync message information into an outgoing message buffer but the caller did not specify the outgoing message buffer address. The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-FMTNULLPRM

3-Error

Missing parameters in sync message format request for data type [dec]

A function was invoked to store sync message information into an outgoing message buffer but the caller failed to specify either the location of the search key for the the database entity to be synched or the address of the outgoing message buffer The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-SYNCNULLPRM

3-Error

Missing parameters in sync message format or decode request for data type [dec]

For a function invoked to execute a sync update on the standby RP the caller failed to specify a valid pointer for holding the result of a search for the database information to be updated. The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DECODENULL

3-Error

No message buffer specified for standby sync of database type [dec] or unsupported address type.

A function was invoked to perform a database sync operation on the standby RP but the caller did not specify the address of the sync message containing the information required for performing the sync operation. Or the address type is unsupported. The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-LOCFUNC

3-Error

No database entity search function defined for sync type [dec]

A function was invoked to store sync message information into an outgoing message buffer but no function exists for locating a database entry of the specified type. The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-NOSYNCARG

3-Error

NULL argument pointer specified for PIM data sync type [dec].

A function was invoked to sync PIM information but the caller did not provide a valid data pointer. The sync operation for this database entity type can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-CAP_PROP_NULL_CTX

3-Error

NULL client context for ISSU capability TLV setup.

The callback function responsible for creating a capability type TLV was invoked by the ISSU infrastructure with a NULL client context. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-CAP_PROC_NULL_CTX

3-Error

NULL client context for ISSU capability TLV processing.

The callback function responsible for processing a capability type TLV was invoked by the ISSU infrastructure with a NULL client context. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-EMPTY_CAP_PROPOSE_TABLE

3-Error

Empty capability table for ISSU capability TLV setup.

The callback function responsible for creating a capability type TLV was invoked by the ISSU infrastructure with a capability table containing no capability types. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-EMPTY_CAP_GROUP

3-Error

Empty capability group for [chars] ISSU client capability TLV setup.

The callback function responsible for creating an ISSU capability type TLV found that the count of capability entries in its client context table was zero. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-INVALID_CAP_PROPOSE_TABLE

3-Error

Invalid capability table for [chars] client ISSU capability TLV setup.

The callback function responsible for creating a capability type TLV was invoked by the ISSU infrastructure with a capability table that did not match any of the registered entries for this client. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ALLOC_CAP_TLV

3-Error

Failed attempt to allocate memory for [chars] client capability TLV

The callback function responsible for creating an ISSU capability type TLV list was unable to allocate memory to hold the TLV list. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-TABLE_INVALID_CAP_TYPE

3-Error

Invalid capability type found in [chars] client capability entry.

The callback function responsible for creating an ISSU capability type TLV list encountered a capability type for which no handling is available. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ISSU_TLV_INSERT

3-Error

Failed to insert entry in ISSU capability TLV list for [chars] client

The callback function responsible for creating an ISSU capability type TLV list encountered a failure when attempting to insert an entry into a TLV list. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ISSU_EMPTY_TLV

3-Error

Empty TLV list received for ISSU [chars] client capability processing

The callback function responsible for processing an ISSU capability type TLV list received an empty TLV list. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-ISSU_PROC_CAP_TYPE

3-Error

Invalid capability type found in [chars] client capability entry.

The callback function responsible for processing an ISSU capability type TLV list encountered a capability type for which no handling is available. Capability negotiation can not proceed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-NEGOMSGINV

3-Error

Invalid negotiation status for [chars] client message

ISSU infrastructure evaluation of a received message for this client failed to identify the message as a negotiation message or a user message. The message can not be processed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MVRF_NAME

3-Error

MVRF lookup for VRF [chars] failed.

An MVRF lookup failed for a VRF name known to be associated with an existing MVRF table. This indicates incorrect setup of search parameters. A PIM data synch operation has been aborted.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MVRF_TABLEID

3-Error

MVRF lookup for tableid [dec] failed.

An MVRF lookup failed for a table ID known to be associated with an existing MVRF table. This indicates incorrect setup of search parameters. A PIM data synch operation has been aborted.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-PRM_LOOKUP

3-Error

PIM RP mapping range lookup for VRF [chars] range [chars]/[dec] failed.

A PIM RP mapping range lookup failed for a range that is known to exist. This indicates incorrect setup of search parameters. A PIM data synch operation has been aborted.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-RPDF_NO_IDB

3-Error

No IDB for if_number [dec] in Bidir RP DF sync attempt for RP address [inet].

The IDB if_number specified in a function call to trigger synching of Bidir RP DF information does not map to any existing IDB. The sync operation can not proceed. The DF information may no longer be correct following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MCAC_NO_IDB

3-Error

No IDB for if_number [dec] in mCAC reservation sync attempt for SG [chars] [chars]

-

-

-

MCASTRED-3-MCAC_DELETE_ALL_NO_IDB

3-Error

Failed to find IDB for mCAC [chars] reservation DB delete. AF = [dec] Reason: [chars]

Lookup of the IDB for the specified input parameters failed either because of an invalid input parameter or incorrect/missing entries in tables used for the lookup. The requested DB delete operation can not proceed. Extraneous mCAC reservations may exist temporarily following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MCAC_COST

3-Error

Deleted mCAC reservation cost for [chars] [chars] if_number [dec]

The accumulated total source or group cost for the affected mCAC reservation DB should always be the greater than the cost of any reservation within the database. This logic error means that the accounting is incorrect. As a result the amount of bandwidth initially reserved for multicast state previously admitted by the current mCAC configuration may be incorrect following an RP failover. This may lead to some disruption of multicast traffic following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MCAC_SEQ

3-Error

Missing standby mCAC configuration for [chars] [chars] mCAC

During handling of an mCAC reservation sync request on the standby RP the corresponding mCAC limit configuration was not found. This is probably a result of a sequencing problem between synching of multicast configuration information and synching of dynamic state information. As a result the amount of bandwidth initially reserved for multicast state previously admitted by the current mCAC configuration may be incorrect following an RP failover. This may lead to some disruption of multicast traffic following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MCAC_RADIX_INIT

3-Error

Failed to update radix tree for mCAC reservation [chars] DB for [chars] [chars] mCAC reservation on interface number [dec]

-

-

-

MCASTRED-3-MCAC_RADIX_DELETE

3-Error

Failed to delete radix tree node for mCAC reservation [chars] DB. Address [chars] Mask [chars]

During handling of an mCAC reservation database element deletion an attempt to delete the affected element from the mCAC reservation database radix tree failed. As a result the amount of bandwidth initially reserved for multicast state previously admitted by the current mCAC configuration may be incorrect following an RP failover. This may lead to some disruption of multicast traffic following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-RPDF_NULL_IDB

3-Error

NULL IDB pointer in Bidir RP DF sync attempt for RP address [inet].

A NULL IDB address was specified in a function call to trigger synching of Bidir RP DF information. The DF information may no longer be correct following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MRIB_UPD_NULL_TABLE

3-Error

NULL table pointer specified for MRIB update notification.

A NULL table address was specified in a function call to notify the PIM HA process that all pending updates have been read for a given multicast routing table. The process will attempt to continue with RP switchover handling despite this error.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HLD_RLS_NO_TABLE

3-Error

No table for tableid 0x[hec] specified for multicast NSF holdoff release.

A table ID for which no table exists was specified as an input to a function registered for releasing of a multicast NSF holdoff lock. If the calling client has a real holdoff extension request pending for some table the lock will not be released until the holdoff failsafe timer expires. This could delay completion of multicast reconvergence following an RP failover.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-INV_PORT_TYPE

3-Error

Invalid communication port identifier [dec] specified for ISSU port up/down handling

The communication port identifier specified for PIM ISSU tranport up/down handling has an undefined value. PIM ISSU communication port up/down handling can not proceed. PIM ISSU functionality may be impaired or lost.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-HOLDOFF_FAILSAFE

3-Error

[chars] PIM NSF failsafe timer expired. Holding client mask = 0x[hec]

One or more clients requested extension of the PIM NSF holdoff period but did not release the holdoff within the maximum allowed time interval. PIM is forcing termination of the NSF holdoff period and resumption of normal flow of multicast routing information but one or more clients may not be ready to resume normal operation.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DDE_REPLAY_FAILSAFE

3-Error

PIM NSF Data Driven Event failsafe timer expired. First waiting table/VRF is \[chars]\

MFIB replay of data driven events and subsequent MRIB update processing has not completed within the maximum allowed time interval. PIM is forcing termination of the DDE replay monitoring period but some multicast routing information may not have been restored.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DDE_REPLAY_BAD_AF

3-Error

Invalid Address Family for PIM NSF data driven event replay completion.

Notification for completion of MFIB data driven event DDE

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-MRIB_PEND_UPD_CHK_BAD_AF

3-Error

Invalid Address Family for PIM pending mrib update check

Registry service invocation to check for pending PIM mrib updates specified an invalid Address Family. The check can not be completed. Some pending updates may not be handled correctly resulting in delayed multicast re-convergence.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BAD_AF

3-Error

Invalid Address Family [dec] for PIM SSO handling.

An IP multicast SSO function received an invalid Address Family input parameter. A subsequent timeout error and routing convergence delay is likely.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BAD_ADDR_TYPE

3-Error

Invalid Address Type [dec] for PIM SSO handling.

An IP multicast SSO function received an invalid Address Type input parameter. Synching of the affected database type to the standby RP can not be completed.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-INV_CKPT_MSG

3-Error

Received invalid CF message. client = [dec] entity = [dec] type = [dec]

An invalid Checkpoint Facility message was received by the PIM HA checkpoint client. The message can not be processed. A possible loss of database syncrhronization between the primary and standby RPs is possible.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-SPURIOUS_MGD_TIMER_EXP

3-Error

Managed timer wakeup received by the PIM HA process with no expired timers.

The PIM HA process received a wakeup for managed timer expiration but the API to obtain the first expired timer returned a NULL pointer. The timer expiration can not be handled. Possible loss of state synchronization between the primary and standby RP may occur.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-UNKNWOWN_CONV_AFI

3-Error

Failed to determine converged address family for topoid 0x[hec]

On reception of unicast convergence notification for a specified routing table the PIM HA process attempted to obtain the address family ID AFI for the converged table. This attempt received a

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-NULL_PIM_RED_CB

3-Error

Invalid [chars] address family PIM redundancy control block.

During initialization of PIM redundancy control blocks an invalid NULL value was provided for one of the address family

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DDE_REPLAY_NULL_TABLE

3-Error

NULL table specified for [chars] DDE replay.

An invalid NULL value was specified in a call to handle

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BAD_DBG_PRM

3-Error

Invalid parameter value in multicast redundancy debug command handling.

An invalid NULL or out of bounds value was specified in a call

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BAD_SYNC_TYPE

3-Error

PIM sync type [dec] is invalid or too large.

An out of bounds value was specified in a call to set or get pim sync type bit array. The value is either greater than PIM_SYNC_TYPE_MAX or greater than the length of the bit array.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-EMPTY_FUN_CALL

3-Error

The default empty function [chars] is called.

The default empty function called the real function seems have not been hooked up yet. This happens when function called before function hooked up.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DUP_ENQUEUE

3-Error

This element is already in queue.

The element is already in queue. The current logic does not allow this to happen. Please investigate why the element is in queue.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-BAD_EVENT_TYPE

3-Error

Defrd sync event type [dec] is invalid.

An invalid value was specified in a call to handle events which deferred sync elements are waiting for. The value is greater than PIM_SYNC_WAIT_FOR_EVENT_MAX.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-DEFER_SYNC_FAILURE

3-Error

Sync failure in standby defer sync operation.

An element which was scheduled to be synched later has failed to sync either upon arrival of the event it was waiting for or it has waited in the deferred sync queue for more than 1 minute.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-UCAST_CONV_STBY

3-Error

Spurious unicast convergence notification received on standby RP for table [chars].

Unicast convergence notification was erroneously signalled on the standby RP for the specified multicast table or VRF. This convergence notification is being ignored.

-

LOG_STD_SH_TECH_ACTION

MCASTRED-3-NO_SR_CONFIG_SYNC

3-Error

The Service Reflect Rule is being synced before Config sync is done.

The Service Reflect Rule sync handled by Mcast HA requires Config sync to have already happened. Since the config sync has not yet happened we are ignoring the Service Reflect Rule sync.

-

LOG_STD_SH_TECH_ACTION

MLDP-4-RW_REGISTER_FAIL

4-Warning

mLDP failed to register to the unicast RIB

routing update in the network.

mldp

LOG_STD_ACTION

MLDP-4-RW_UNREGISTER_FAIL

4-Warning

mLDP failed to un-register to the unicast RIB

or Route-watch process due to some reason.

mldp

LOG_STD_ACTION

MLDP-4-RW_TRACK_START_FAIL

4-Warning

mLDP failed to start tracking a prefix in the unicast RIB

in the RIB due to some reason.

mldp

LOG_STD_ACTION

MLDP-4-RW_TRACK_STOP_FAIL

4-Warning

mLDP failed to stop tracking a prefix in the unicast RIB

in the RIB due to some reason.

mldp

LOG_STD_ACTION

MLDP-4-RW_GET_NOTIF_FAIL

4-Warning

mLDP failed to get information from the unicast RIB -- RIB Error Code - 0x[hec]

prefix from the RIB due to some reason.

mldp

LOG_STD_ACTION

MLD_PROT-3-SHUTDOWN_ERR

3-Error

Error in [chars] : [chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

MLD_PROT-3-STARTUP_ERR

3-Error

Unable to start to MLD process

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

MLD_PROT-3-PAK_ERR

3-Error

An internal error occured while processing a packet queue

Managed queue event received without a packet. Internal Error

ipmulticast

LOG_STD_RECUR_ACTION

MLD_PROT-4-LIMIT_REACHED

4-Warning

State limit reached report on [chars] ignored for [chars]

MLD report ignored because state limit was reached.

ipmulticast

LOG_STD_NO_ACTION

MLD_PROT-6-IDB_ENABLE

6-Information

Interface [chars] does not support multicast not enabled

IGMP/MLD not enabled on an interface that does not support mcast

ipmulticast

LOG_STD_NO_ACTION

MLD_PROT-4-SUSPEND_RESUME_WARNING

4-Warning

Failed to resume suspended IGMP/MLD context.

A loop in IGMP/MLD code was temporarily suspended to avoid hogging the CPU. When it was time to resume the loop the system was unable to do so. Possible reasons for this are that a VRF was deleted or an interface was deleted while the loop was suspended.

ipmulticast

LOG_STD_NO_ACTION

MLD_PROT-3-TABLE_ERR

3-Error

[chars]

Errors related to IGMP table creation and management

ipmulticast

LOG_STD_RECUR_ACTION

MLD_PROT-3-INTERNAL_ERR

3-Error

[chars]

Internal error

ipmulticast

LOG_STD_RECUR_ACTION

PIM-6-INVALID_RP_JOIN

6-Information

Received * [inet] Join from [inet] for invalid RP [inet]

A downstream PIM router sent a join message for the shared tree which\n this router does not want to accept. This behavior indicates that this\n router will let only downstream routers join to a specific rendezvous\n point.

-

"Configure all downstream leaf routers to join to the RP that is\n" "allowed by upstream routers toward the validated rendezvous point."

PIM-4-RP_NOT_LOCAL

4-Warning

Received * [inet] Join from [inet] for invalid RP [inet]. SDWAN SPT-only is

A downstream PIM router sent a join message for the shared tree with a rendezvous point IP which is not local. In SDWAN spt-only networks it is expected that the cEdge is the chosen RP.

-

"Make sure the cEdge is the chosen RP and If PIM BSR is running " "use appropriate BSR configurations to make cEdge as the elected RP if there" "is a contention."

PIM-1-INVALID_RP_REG

1-Alert

Received Register from router [inet] for group [inet] [inet] not willing to be RP

A PIM router received a register message from another PIM router that\n thinks it is the rendezvous point. If the router is not configured for\n another rendezvous point it will not accept the register message.

-

"Configure all leaf routers first-hop routers to multicast sources\n"

PIM-4-INVALID_SRC_REG

4-Warning

Received Register from [inet] for [inet] [inet] not willing to be RP

-

-

-

PIM-1-SR_INTERVAL_SETTING_ERR

1-Alert

Incompatible SR interval from [inet] on [chars] [dec] != [dec]

-

-

-

PIM-4-DEPRECATED_HELLO_TLV

4-Warning

Deprecated PIM Hello Option TLV [dec] [chars] from [inet] [chars]

-

-

-

PIM-4-NOT_RECOMMENDED_DENSE_MODE

4-Warning

PIM Dense Mode is not recommended and needs to be replaced with PIM Sparse Mode

PIM Dense Mode is not recommended and needs to be replaced with PIM Sparse\n Mode.

-

"Configure PIM Sparse Mode"

PIM-3-REGTUNMVRF

3-Error

NULL mvrf specified in PIM register tunnel creation request for RP [inet]

An NULL mvrf was specified for creation of\n a PIM register tunnel associated with the specified RP.\n The register tunnel can not be created.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNUPMVRF

3-Error

NULL mvrf specified in PIM register tunnel entry for RP [inet]

An NULL mvrf was specified for the PIM register tunnel associated \n\n\ with the specified RP.\n\n\ The register tunnel can not be used for registration.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNRPMAPMVRF

3-Error

NULL mvrf specified in RP mapping notification for RP [inet]

An NULL mvrf was specified when a PIM RP mapping notification\n\n\ was made.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNQLINK

3-Error

Corrupted PIM register [chars] tunnel queue links. Can't add RP [inet]

Insertion of a new PIM register tunnel entry into a PIM register\n tunnel queue failed. The encapsulation or decapsulation tunnel can\n not be created.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNMISSING

3-Error

[chars] register tunnel entry for RP [inet] missing from tunnel list

Deletion of a PIM register tunnel entry from a PIM register\n tunnel queue failed because the register tunnel entry wasn't found\n in the register tunnel list.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNRP

3-Error

NULL RP pointer specified for PIM register tunnel creation.

The caller passed a NULL pointer instead of providing a valid \n pointer to the RP cache entry for which register tunnel creation\n was requested. The encapsulation or decapsulation tunnel can not\n be created.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNPRQ

3-Error

Process enqueue for [chars] register tunnel creation failed for RP [inet].

An attempt to enqueue a request for PIM register tunnel IDB\n creation failed probably because of a lack of resources. The\n

-

LOG_STD_SH_TECH_ACTION

PIM-3-RPNOREGTUN

3-Error

For multicast route [inet] [inet] no register tunnel found

During an attempt to install a register tunnel interface for a\n new SG multicast route a search in the PIM register encapsulation\n tunnel list failed to find the tunnel entry for the corresponding\n RP. The register tunnel interface can not be added to the multicast\n route.

-

LOG_STD_SH_TECH_ACTION

PIM-3-RPNOREGTUNIDB

3-Error

For multicast route [inet] [inet] no register tunnel IDB found

During an attempt to install or uninstall a register tunnel \n interface for an SG multicast route the register tunnel entry for \n the corresponding RP did not specify a tunnel interface.\n The register tunnel interface can not be added to or removed from \n the multicast route.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNNOIDB

3-Error

No register tunnel IDB found for RP [inet]. Can't execute pending delete

During an attempt to delete a register tunnel interface that\n is currently in use for at least one mroute olist entry\n the register tunnel entry did not specify a tunnel interface.\n The register tunnel interface can not be deleted.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNIDBCREATE

3-Error

Tunnel IDB creation for a PIM register [chars] tunnel for RP [inet] failed for vrf [chars].

An attempt to create a tunnel IDB for use with a PIM register\n tunnel has failed. The encapsulation or decapsulation tunnel can\n not be created.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNSETSRC

3-Error

Failed to set PIM [chars] register tunnel IDB source for RP [inet]

An attempt to set the tunnel source address of a PIM register tunnel\n for the specified RP has failed. The encapsulation or decapsulation\n tunnel can not be created.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNIDBMVRF

3-Error

Failed to find the mvrf associated with IDB [chars]

An attempt to determine the multicast vrf associated with the\n specified IDB failed. The required update of PIM register tunnel\n IDB information can not proceed.

-

LOG_STD_SH_TECH_ACTION

PIM-3-REGTUNMDBFLG

3-Error

Register tunnel MDB client flag allocation failed.

An attempt to allocate a client flag position for use in tracking the number of mroutes using each PIM register tunnel has failed. Register tunnels can be allocated but can not deleted.

-

LOG_STD_SH_TECH_ACTION

PIM-6-REGTUNNOTDEL

6-Information

Some register [chars] tunnels may not have been deleted.

Maintanance activity to delete unused register tunnels was running over time and some tunnels may not have been deleted.

-

LOG_STD_SH_TECH_ACTION

PIM-4-REGTUNNOSRC

4-Warning

Some register encap tunnels may not have routable source addresses.

Repeated attempts to adjust register encap tunnel source were running over time and some tunnels may not have been adjusted.

-

LOG_STD_SH_TECH_ACTION

PIM-5-NBRCHG

5-Notice

neighbor [inet] [chars] on interface [chars] [chars]

A PIM neighbor has gone UP or DOWN on an interface

-

LOG_STD_NO_ACTION

PIM-5-DRCHG

5-Notice

DR change from neighbor [inet] to [inet] on interface [chars]

A PIM neighbor is the new DR on an interface

-

LOG_STD_NO_ACTION

PIM-3-MVRF_NULL_PRM

3-Error

Null parameter specified for MVRF lookup.

A function to perform an mvrf lookup by name detected a NULL input parameter. The intended action can not proceed.

-

LOG_STD_SH_TECH_ACTION

PIM-3-UPD_RPR_NULL_PRM

3-Error

Null parameter specified for Bidir RP route update.

A function to perform an update of Bidir RP route information detected a NULL input parameter. The update can not proceed.

-

LOG_STD_SH_TECH_ACTION

PIM-3-RPDF_NULL_PRM

3-Error

Null parameter specified for Bidir RP DF creation.

A function to create a Bidir RP DF entry detected a NULL input parameter. The RP DF entry can not be created.

-

LOG_STD_SH_TECH_ACTION

PIM-3-PMTFINDSMRPINPRM

3-Error

Invalid parameter passed while walking the autorp cache to find a group-to-rp mapping for Sparse RP [inet]. parameter: 0x[hec]

An invalid parameter was specified while walking the\n\ autorp cache to find a Sparse RP match.

-

LOG_STD_SH_TECH_ACTION

PIM-3-TWHEEL_INIT_ERR

3-Error

Unable to create PIM timer wheel

An error occured intializing the PIM timer twheel

-

"An error in maintaining the PIM timer wheel occurred." LOG_STD_ACTION

PIM-3-SPURIOUS_MGD_TIMER_EXP_SRC_CHK

3-Error

Managed timer wakeup received by the PIM register tunnel creation process with no expired timers.

The PIM register tunnel creation process received a wakeup for managed timer expiration but the API to obtain the first expired timer returned a NULL pointer. The timer expiration can not be handled. Possible loss of PIM register tunnel functionality including failure of PIM Sparse Mode registration for some multicast groups may occur as a result.

-

LOG_STD_SH_TECH_ACTION

PIM-3-PRT_ENTRY_HAS_NO_RP

3-Error

A request has been issued to remove a PIM register tunnel from multicast entry [chars] [inet] but this entry has no RP address.

This condition is an indication that the entry's RP address was reset before first removing the register tunnel. This can cause a memory leak because the RP address is the key for looking up the tunnel whose removal has been requested. Without the RP we cannot find the tunnel and decrement its reference count.

-

LOG_STD_DBG_ACTION

PIM-3-PRT_INVALID_MODE

3-Error

Invalid register tunnel mode [dec].

The only valid register tunnel mode values are TUN_MODE_PIM_ENC_IPV4 and TUN_MODE_PIM_DEC_IPV4.

-

LOG_STD_DBG_ACTION

PIM-4-PIM_INVALID_SB

4-Warning

Unexpected access to PIM interface subblock field

IOS attempts to access the value of a PIM interface field\n\ whose interface subblock is not yet created

-

"An inconsistency accessing a PIM interface subblock occurred." LOG_STD_ACTION

PIM-4-NO_INPUT

4-Warning

PIM packet without input interface received from [inet] for [inet]

An unexpected PIM packet without input interface was received.

ipmulticast

"Consider taking note of source and destination present in syslog." LOG_STD_ACTION

PIM-4-TRANSPORT_ATTR_NOT_PRESENT

4-Warning

Transport ATTR should be present for PIM J/P with LISP transport

Transport ATTR should be present for PIM J/P with LISP transport.

ipmulticast

LOG_STD_NO_ACTION

PIM-4-UNSUPPORTED_LISP_TRANSPORT

4-Warning

Unsupported LISP transport

Unsupported LISP transport

ipmulticast

LOG_STD_NO_ACTION

PIM-4-RCV_RLOC_ATTR_NOT_PRESENT

4-Warning

Receiver RLOC ATTR should be present for PIM J/P with LISP transport

Receiver RLOC ATTR should be present for PIM J/P with LISP transport

ipmulticast

LOG_STD_NO_ACTION

PIM-4-INVALID_RCV_RLOC

4-Warning

Invalid Receiver RLOC address family

Invalid Receiver RLOC address family

ipmulticast

LOG_STD_NO_ACTION

PIM-3-UNEXPECTED_CONDITION_SPMSI

3-Error

PIM [dec] A mismatch of the S-PMSI pointer %p/ %p cached in the mdb [inet]/%

-

-

-

PIM-5-PROXY

5-Notice

Deny proxy for [inet] [inet] from neighbor [inet]

Deny PIM Proxy from neighbor

-

LOG_STD_NO_ACTION

AUTORP-2-RADIXINIT

2-Critical

Error initializing the Auto-RP radix tree

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

AUTORP-4-RADIXINSERT

4-Warning

Error inserting a new entry into the RP-mapping radix tree

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

AUTORP-4-PRM_DEL

4-Warning

Error expiring semi-static RP-mapping entry [inet]/[dec] RP:[inet]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

AUTORP-5-MAPPING

5-Notice

RP for [inet]/[dec] is now [inet]

A new RP has been elected for the subject group prefix

-

LOG_STD_NO_ACTION

AUTORP-4-PAK_ERR

4-Warning

AutoRP [chars] packet is received on interface [chars] with Source address=[inet] Destination address=[inet] TTL=[dec] IP length=[dec] Datagram size/UDP length=[dec]

The AutoRP packet was received with wrong packet length. The packet has been dropped as it may be a malformed packet.

-

LOG_STD_NO_ACTION

AUTORP-4-OVERLAP

4-Warning

AutoRP [chars] packet group [inet] with mask [inet] removed because of multicast boundary for [inet] with mask [inet]

The multicast boundary has a longer network mask than the AutoRP encoded group.

-

"Use postive permit clauses in the AutoRP Access " "Control List"

AUTORP-5-CRP_REMOVED

5-Notice

C-RP [inet] on interface [chars] has been removed

This is performed either because PIM is disabled on the interface or \n the interface card has been removed

-

LOG_STD_NO_ACTION

AUTORP-6-RP_MAPPING_IDB_DEL

6-Information

AutoRP RP-MAPPING IDB [chars] is deleted

The configured rp-mapping idb has been deleted.

-

LOG_STD_NO_ACTION

BSR-5-CRP_REMOVED

5-Notice

Candidate-RP on interface [chars] has been removed

This is performed because the interface card has been removed

-

LOG_STD_NO_ACTION

BSR-5-CBSR_REMOVED

5-Notice

Candidate-BSR on interface [chars] has been removed

This is performed because the interface card has been removed

-

LOG_STD_NO_ACTION

BSR-6-NO_FORWARD_BSR

6-Information

Dropping No-Forward Bootstrap message from [chars] on [chars]

This is performed because RFC 5059 No-Forward BSM is not supported.

-

LOG_STD_NO_ACTION

BSR-4-CRP_NOT_CONFIGURED

4-Warning

Bootstrap message received from [inet] on [chars] SDWAN running SPT-only mode but Candidate-RP not configured locally.

In SDWAN spt-only networks it is expected that the cEdge is the candidate RP and elected RP if PIM BSR is running.

-

LOG_STD_ACTION

MFIB-2-NOMEMORY

2-Critical

Out of memory for IP multicast MFIB. Used: %lu Free: %lu

Insufficient memory for the IP multicast forwarding\n\ information base. Multicast packets may not be properly\n\ routed.

-

LOG_STD_SH_TECH_ACTION

PIM_REG_TUN-3-UNNUM_ERR

3-Error

Failed to set un-numbered interface for [chars] [chars]

-

-

-

PIM_REG_TUN-3-SERVICE_POLICY_FAILURE

3-Error

Failed to configure service policy on register tunnel.

When the ip pim register-rate-limit CLI command is entered a rate-limiting policy-map is created. This policy-map is attached to each register tunnel by configuring an output service policy on the tunnel. This message is logged as a result of a failure to configure an output service policy on a register tunnel. This failure may be due to lack of temporary resources but it may also be caused by platform restrictions on overlapping QoS configurations such as simultaneously having a service policy on a tunnel and on the real interface associated with the tunnel.

ipmulticast

LOG_STD_SH_TECH_ACTION

PIM_REG_TUN-3-NO_POLICY_MAP

3-Error

Lookup of rate-limit policymap failed for vrf [chars].

When the ip pim register-rate-limit CLI command is entered a rate-limiting policy-map is created. This policy-map is attached to each register tunnel by configuring an output service policy on the tunnel. A policy-map lookup is therefore performed whenever the register-rate-limit command is enabled or disabled. This message is logged as a result of a lookup failure.

ipmulticast

LOG_STD_SH_TECH_ACTION

PIM_REG_TUN-3-UNEXPECTED_TRANSPORT

3-Error

Unexpected tunnel transport: [dec].

An unexpected tunnel transport was detected. The location where the value was detected and the execution path that lead to it may be obtained from the traceback included in this message.

ipmulticast

LOG_STD_SH_TECH_ACTION

PIM_REG_TUN-3-PRT_NULL_TINFO

3-Error

Register tunnel [chars] has null tinfo.

Unable to dereference tunnel information.

ipmulticast

LOG_STD_DBG_ACTION

PIM_REG_TUN-3-IDB_ROUTE_DISABLE

3-Error

Tunnel Groups: [chars]: [chars]

The tunnel group component encountered an internal software error

ip-tunnels

LOG_STD_ACTION

AMT-2-GATEWAY_INIT

2-Critical

Error initializing AMT Gateway

Insufficient memory is available to initialize Gateway

-

LOG_STD_SH_TECH_ACTION

AMT-2-RELAY_INIT

2-Critical

Error initializing AMT Relay

Insufficient memory is available to initialize Relay

-

LOG_STD_SH_TECH_ACTION

AMT-2-MSGTYPE_ERR

2-Critical

[chars] AMT message with invalid type [dec]

AMT type is not 1-7

-

LOG_STD_NO_ACTION

AMT-2-PROCESS_ERR

2-Critical

Error initializing AMT process

Can't start the AMT process

-

LOG_STD_NO_ACTION

AMT-2-ADD_GATEWAY

2-Critical

Error adding new Gateway

Can't get memory for a new Gateway [chars] port [dec]

-

LOG_STD_NO_ACTION

AMT-2-RPT_WAVLINIT

2-Critical

Error initializing IGMP Unsolicited Report handler

Insufficient memory is available to initialize the IGMP \n\ Unsolicited Report handler.

-

LOG_STD_SH_TECH_ACTION

MLDP-2-PROCESS_ERR

2-Critical

Error initializing MLDP process

Can't start the MLDP process

-

LOG_STD_NO_ACTION

MLDP-2-MRIB_PROCESS_ERR

2-Critical

Error initializing MLDP MRIB process

Can't start the MLDP MRIB process

-

LOG_STD_NO_ACTION

MLDP-2-CHUNK_ERR

2-Critical

Error initializing MLDP db chunks

Error initializing MLDP db chunks

-

LOG_STD_NO_ACTION

MLDP-2-RADIX_DB_ERR

2-Critical

Error initializing MLDP DB radix tree

Error initializing MLDP_DB radix ree

-

LOG_STD_NO_ACTION

MLDP-2-FEC_ERR

2-Critical

Error the FEC size is too large

The FEC size is too large

-

LOG_STD_NO_ACTION

MLDP-2-PEER_ERR

2-Critical

Received attached address [inet] but there is no LDP peer

Internal error

-

LOG_STD_NO_ACTION

MLDP-2-RADIX_BRANCH_ERR

2-Critical

Error initializing MLDP BRANCH radix tree

Internal error

-

LOG_STD_NO_ACTION

MLDP-5-ADD_BRANCH

5-Notice

[chars] Root: [inet] Add [chars] branch [chars] [chars]

Logging of changes to mLDP branch

-

LOG_STD_NO_ACTION

MLDP-5-MODIFY_BRANCH

5-Notice

[chars] Root: [inet] Modify [chars] branch [chars] [chars]

Logging of changes to mLDP branch

-

LOG_STD_NO_ACTION

MLDP-5-DELETE_BRANCH

5-Notice

[chars] Root: [inet] Delete [chars] branch [chars] [chars]

Logging of changes to mLDP branch

-

LOG_STD_NO_ACTION

MLDP-5-MODIFY_NBR

5-Notice

[chars] Root: [inet] Modify [chars] entry peer [chars] [chars]

Logging of changes to mLDP entry peer

-

LOG_STD_NO_ACTION

MLDP-4-DB_BRANCH_DEL_PENDING

4-Warning

[chars] tree with LSM ID: %X has both IPv4 and IPv6 del_pending set

An mLDP database entry has both the IPv4 and IPv6 del_pending \n\ flags set to TRUE -- This is an inconsistent state

-

LOG_STD_ACTION

MLDP-2-INTERNAL_ERR

2-Critical

Internal mLDP error

Internal error

-

LOG_STD_NO_ACTION

MLDP-5-ROUTING_LOOP

5-Notice

There is a routing loop for this root.

There is a routing loop for this root

-

LOG_STD_NO_ACTION

MLDP-2-FEC_CHUNK_ERR

2-Critical

Error initializing MLDP FEC chunks

Error initializing MLDP FEC chunks

-

LOG_STD_NO_ACTION

MLDP-2-FEC_TBL_ERR

2-Critical

Error initializing MLDP FEC tbl

Error initializing MLDP FEC tbl

-

LOG_STD_NO_ACTION

MLDP-2-FEC_NTF_ERR

2-Critical

Error initializing MLDP FEC notifier

Error initializing MLDP FEC notifier

-

LOG_STD_NO_ACTION

MLDP-2-FILTER_CHUNK_ERR

2-Critical

Error initializing MLDP filter chunks

Error initializing MLDP filter chunks

-

LOG_STD_NO_ACTION

MLDP-2-FILTER_TBL_ERR

2-Critical

Error initializing MLDP filter tbl

Error initializing MLDP filter tbl

-

LOG_STD_NO_ACTION

MLDP-2-FILTER_NTF_ERR

2-Critical

Error registering MLDP filter FEC notifier

Error registering MLDP filter FEC notifier

-

LOG_STD_NO_ACTION

MLDP-2-HA_INSERT_ERR

2-Critical

Error inserting node into MLDP HA radix tree

Error inserting node into MLDP HA radix tree

-

LOG_STD_NO_ACTION

MLDP-2-ID_RESERVE_ERR

2-Critical

Error reserving id for mldp database

Error reserving id for mldp database

-

LOG_STD_NO_ACTION

MLDP-2-PEER_NOT_FOUND

2-Critical

Peer doesn't exist while syncing to standby

Peer doesn't exist while syncing to standby

-

LOG_STD_NO_ACTION

MLDP-2-ROOT_NOT_FOUND

2-Critical

Root doesn't exist while syncing to standby.

Root doesn't exist while syncing to standby

-

LOG_STD_NO_ACTION

MFIB_PLTF-3-UPDATE_SET_MEMORY

3-Error

[chars] %p -> [chars] [%p %p/[chars]]

Failed to allocate memory for platform transaction.

-

LOG_STD_REDUCE_ACTION

MFIB_PLTF-3-TRANSACTION_MEMORY

3-Error

[dec] [dec]

Failed to allocate memory for platform transaction.

-

LOG_STD_REDUCE_ACTION

MFIB_PLTF-3-HANDLE_CONSTRAINT

3-Error

[chars] %p

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_PLTF-3-TABLE_HANDLE_BAD

3-Error

[chars]. %p

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_PLTF-3-ENTRY_HANDLE_BAD

3-Error

[chars]. %p

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_PLTF-3-IOITEM_HANDLE_BAD

3-Error

[chars]. %p

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_PLTF-3-TABLE_LOCK_FAIL

3-Error

[chars]. [chars] table %p %p %p/[chars]

-

-

-

MFIB_PLTF-3-TABLE_UNLOCK_FAIL

3-Error

[chars]. [chars] table %p %p %p/[chars]

-

-

-

MFIB_PLTF-3-ENTRY_LOCK_FAIL

3-Error

[chars]. [chars] entry %p [chars] [%p %p/[chars]]

-

-

-

MFIB_PLTF-3-ENTRY_UNLOCK_FAIL

3-Error

[chars]. [chars] entry %p [chars] [%p %p/[chars]]

-

-

-

MFIB_PLTF-3-IOITEM_LOCK_FAIL

3-Error

[chars]. [chars] ioitem %p [chars] [chars] [%p %p/[chars]]

-

-

-

MFIB_PLTF-3-IOITEM_UNLOCK_FAIL

3-Error

[chars]. [chars] ioitem %p [chars] [chars] [%p %p/[chars]]

-

-

-

MFIB_PLTF-7-ENTRY_DUPLICATE_ADD

7-Debug

[chars] entry [chars] [%p %p/[chars]]

-

-

-

MFIB_PLTF-3-IOITEM_DUPLICATE_ADD

3-Error

[chars] ioitem [chars] [chars] [%p %lx/[chars]]

-

-

-

MFIB_PLTF-3-ANNOT_TOO_LONG

3-Error

[chars] %p [dec]

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_PLTF-3-CALLBACK_RETURN_INVALID

3-Error

[chars]. %p %p %p

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_PLTF-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

-

LOG_STD_ACTION

MFIB_PLTF-3-XDRISSUREGERROR

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_STATS-3-MFIB_STATS_RP_FAILED_GET_IPC_MSG

3-Error

RP failed allocating ipc message buffer for linecard slot = [dec]

The Route Processor failed in allocating buffer for getting linecard statistics

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_RP_FAILED_SEND_IPC_MSG

3-Error

RP failed in sending ipc msg to the linecard slot = [dec] error = [chars]

The Route Processor has failed in sending a statistics message to the Linecard

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_RP_FAILED_REPLY_MSG

3-Error

RP received reply with error status from linecard slot = [dec]

The Route Processor has received reply with error in statistics message from a linecard

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_LC_FAILED_GET_IPC_MSG

3-Error

Linecard failed allocating ipc message buffer

The Linecard failed in allocating buffer for sending statistics

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_LC_FAILED_SEND_MSG

3-Error

Linecard failed in sending msg to the Route Processor error = [chars]

The Linecard has failed in sending statistics message to the Route Processor

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_LC_MSG_TOO_BIG

3-Error

Linecard failed to return counters message buffer too small.

The Linecard has failed to return counters because the minimum message size exceeds the maximum IPC buffer size.

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_FAILED_CREATE_MUTEX

3-Error

Hardware stats destructor failed to create watched boolean

Hardware stats failed to create a mutex when deleting a hardware stats structure.

-

LOG_STD_SH_TECH_ACTION

MFIB_STATS-3-MFIB_STATS_FAILED_GET_MUTEX

3-Error

Hardware stats destructor failed to push event list

Hardware stats failed to hold a mutex when deleting a hardware stats structure.

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-FAILED_ENTRY_POST

3-Error

For [chars] in table %p %p/[chars] with [chars]%lx

-

-

-

MFIB_MRIB-3-FAILED_IOITEM_POST

3-Error

For [chars] [chars] in table %p %p/[chars] with [chars]%lx

-

-

-

MFIB_MRIB-3-FAILED_TABLE_REGISTER

3-Error

In table %p %p/[chars] with [chars]%lx

An MFIB table failed to register with the MRIB

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-FAILED_TABLE_OPEN

3-Error

In table %p %p/[chars] with [chars]%lx

An MFIB table failed to connect to the MRIB

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-FAILED_TABLE_FILTER

3-Error

In table %p %p/[chars] with [chars]%lx

The MFIB failed to configure an MRIB connection.

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-FAILED_TABLE_UNBIND

3-Error

In table %p %p/[chars] with [chars]%lx

An MFIB table failed to disconnect from the MRIB

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-TABLE_MESSAGE

3-Error

In table %p %p/[chars] : [chars]

MFIB has encountered an error while processing a message sent by MRIB.

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-TABLE_UPDATE

3-Error

In table %p %p/[chars] : [chars]

MFIB has encountered an error while processing an MRIB database update.

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-FAILED_ENTRY_CREATE

3-Error

For [chars] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-FAILED_IOITEM_CREATE

3-Error

For [chars] [chars] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-FAILED_WIRE_FIND

3-Error

For [chars] %p [[chars]/[chars]] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-FAILED_WIRE2IF_NUMBER

3-Error

For [chars] %p [[chars]/[chars]] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-FAILED_CONNID_FIND

3-Error

For [chars] %p [[chars]/[chars]] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-FAILED_CONNID_RESERVE

3-Error

For [chars] %p [[chars]/[chars]] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-FAILED_CONNID_LOCK

3-Error

Failure code [dec] on attempt to lock connid 0x[hec] for interface [chars] of entry [chars] in table ID 0x[hec]. Actual connid is 0x[hec]

Failed to acquire an MFIB lock for a connection ID on the standby RP or on an LC. Forwarding for the affected multicast flow may be affected after an RP failover.

-

LOG_STD_SH_TECH_ACTION

MFIB_MRIB-3-GIVEN_NULLIFHNDL

3-Error

For [chars] in table %p %p/[chars]

-

-

-

MFIB_MRIB-3-GENERATED_NULLIFHNDL

3-Error

For [chars] [chars] in table %p %p/[chars]

-

-

-

MFIB-6-PAK_TTL_ONE_V4

6-Information

IPV4 Multicast Packet received with ttl <= 1

An IP non-linklocal multicast packet received with ttl 1

-

LOG_STD_NO_ACTION

MFIB-6-PAK_TTL_ONE_V6

6-Information

IPV6 Multicast Packet received with ttl <= 1

An IPv6 non-linklocal multicast packet received \ with ttl 1

-

LOG_STD_NO_ACTION

MFIB-6-PAK_TOO_SHORT

6-Information

Packet too short from [chars] datagram size [dec] tl [dec]

The MFIB failed to set offset within packet

-

LOG_STD_SH_TECH_ACTION

MFIB-3-MFIB_CTXT_DEPTH_EXCEEDED

3-Error

-

MFIB has exceeded maximum number of switching contexts

-

LOG_STD_SH_TECH_ACTION

MFIB-3-ADJ_GSB_REGISTER

3-Error

-

Could not register an adjacency GSB identifier

-

LOG_STD_SH_TECH_ACTION

MFIB-3-ADJ_GSB_INIT

3-Error

-

Could not initialise the adjacency GSB memory pool

-

LOG_STD_SH_TECH_ACTION

MFIB-3-SR_ADJ_GSB_REGISTER

3-Error

-

Could not register an SR adjacency GSB identifier

-

LOG_STD_SH_TECH_ACTION

MFIB-3-SR_ADJ_INCORRECT_ADD

3-Error

A different MFIB Service Reflect adj is being added

A different SR adjacency subblock is being added to the \ adjacency without first removing the existing one. This \ indicates that SR forwarding may no longer work correctly

-

LOG_STD_SH_TECH_ACTION

MFIB-3-SR_ADJ_GSB_INIT

3-Error

-

Could not initialise the SR adjacency GSB memory pool

-

LOG_STD_SH_TECH_ACTION

MFIB-3-MRIB_PROCESS

3-Error

[chars][chars]

The MFIB process which intefaces with the MRIB failed to start. The MFIB will be unusable.

-

LOG_STD_SH_TECH_ACTION

MFIB-6-MFIB_HEADER_LIMIT_EXCEEDED

6-Information

[dec] at [chars]

MFIB attempted to exceed maximum number of replicated packet header buffers

-

LOG_STD_SH_TECH_ACTION

MFIB-6-MFIB_POOL_GETBUFFER_FAILURE

6-Information

-

MFIB has failed in an attempt to retrieve a particular type of memory. The MFIB will continue using another memory area

-

LOG_STD_SH_TECH_ACTION

MFIB-3-ILLEGALARGS

3-Error

Illegal arguments - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

MFIB-3-DECAP_OCE_CREATION_FAILED

3-Error

Decap OCE creation failed for [chars]

An internal software error occurred.

-

LOG_STD_ACTION

MFIB-3-WIRE_LOOKUP_OR_ALLOC_FAILED

3-Error

Lookup or allocation of MFIB wire failed

Lookup or allocation of MFIB wire failed

-

LOG_STD_ACTION

MFIB-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

-

LOG_STD_ACTION

MFIB_IPC-3-MFIB_LC_FAILED_IPC_OPEN

3-Error

LC in slot [dec] failed to open IPC port to RP error = [chars].

The linecard has failed to open IPC port towards the Route Processor. No MFIB statistics will be collected from this line card as a result.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_LC_REG_FAIL

3-Error

LC failed to register IPC port: [chars]

The route processor could not register its IPC port. No MFIB statistics will be gathered from linecards.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_LC_SEND_READY_FAILED

3-Error

LC in slot [dec] failed to send LC Ready MSG to RP error = [chars].

The linecard has failed to send a Ready message to the Route Processor. No MFIB statistics will be collected from this linecard.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_RP_FAILED_IPC_SEND

3-Error

IPC message for stats or rates failed code = [dec]

Sending of IPC message for stats or rates failed possibly because of congestion. Stats or rates values may be temporarily affected.

-

LOG_STD_RECUR_ACTION

MFIB_IPC-3-MFIB_RP_FAILED_IPC_ACK

3-Error

LC did not receive Ack for IPC message of size = [dec] type = [dec] error = [chars].

The linecard did not receive an acknowledgement for an IPC message it sent to the Route Processor.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_CREATE_PORT_FAILED

3-Error

Failed to create local IPC port error = [chars]

An IPC port could not be created. This may prevent MFIB statistics being gathered from one or more linecards.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_LC_FAILED_IPC_ACK

3-Error

RP did not receive Ack for IPC message of type = [dec] error = [chars]

The Route Processor did not receive and acknowledgement for an IPC message that was sent to a linecard.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_LC_READY_NOIPC

3-Error

LC failed tp allocate IPC buffer to send LC ready slot = [dec]

The linecard failed to allocate and IPC buffer for the Ready message. MFIB statistics will not be gathered from this linecard.

-

LOG_STD_REDUCE_ACTION

MFIB_IPC-3-MFIB_RP_FAILED_LC_PORT_INFO

3-Error

RP failed to create linecard IPC port info structure slot = [dec]

The Route Processor has failed to create an IPC port for distributed statistics collection

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_RP_FAILED_LC_PORT_OPEN

3-Error

RP failed to open an IPC port for communication with the linecard in slot [dec].

The Route Processor has failed to open an IPC port for distributed statistics collection.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_RP_FAILED_BAD_LC_SLOT

3-Error

RP failed to send IPC message to linecard in slot [dec].

The Route Processor could not send an IPC message to a linecard because the slot number is incorrect.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_RP_REG_FAIL

3-Error

RP failed to register IPC port: [chars]

The route processor could not register its IPC port. No MFIB statistics will be gathered from linecards.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_RCV_FAIL

3-Error

An IPC message was received with an error status: [chars].

An IPC message was received but could not be processed due to an IPC error condition.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-4-MFIB_UNRECOGNISED_MSG

4-Warning

An IPC message was received with an unrecognised subtype [dec]

-

-

-

MFIB_IPC-3-MFIB_BAD_MSG_TYPE

3-Error

An IPC message was received with an incorrect type [dec].

-

-

-

MFIB_IPC-3-MFIB_RP_NO_MEMORY

3-Error

The RP failed to allocate an internal data structure.

The Route Processor failed to allocate memory required to managed linecard IPC connections. No MFIB statistics will be collected from linecards.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_RP_NO_PROCESS

3-Error

The RP failed to create a required process.

The Route Processor failed to create a process required to manage linecard IPC connections. No MFIB statistics will be collected from linecards.

-

LOG_STD_SH_TECH_ACTION

MFIB_IPC-3-MFIB_LC_NO_PROCESS

3-Error

The LC failed to create a required process.

The linecard failed to create a process required to manage linecard IPC connections to the RP. No MFIB statistics will be collected from this linecards

-

LOG_STD_SH_TECH_ACTION

COMMON_MFIB-3- NOMEM

3-Error

Memory allocation failure for [chars] in [chars] MFIB [0x%08x].

An attempt to allocate memory has failed. Depending on the criticality of the data to be stored MFIB operation may be impacted.

COMMON_MFIB_DDTS_COMPONENT

"Verify that the configuration is supported by the memory present in " "the system. Copy the message exactly as it appears and report it " "to your technical support representative."

COMMON_MFIB-3- ILLEGALARGS

3-Error

Illegal arguments - [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-NOBROKER

3-Error

[chars] distribution broker not found - distributing [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-BROKERINITFAIL

3-Error

Failed to initialise [chars] RP broker facility

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-BROKER_ENCODE

3-Error

[chars] broker failed to encode msg type [dec] for slots [chars]

-

-

-

COMMON_MFIB-3-MFIBXDRINV

3-Error

Invalid XDR format. [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-MFIBXDRLEN

3-Error

Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-TABLE

3-Error

[chars]: [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-MFIB_GSB

3-Error

Generic subblock error: [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-4-MFIBXDR_REGISTRATION

4-Warning

Unable to register XDR client [chars].

-

-

-

COMMON_MFIB-4-MFIBXDR_NOTREG

4-Warning

XDR client [chars] should be registered.

-

-

-

COMMON_MFIB-3-MFIBXDR_ISSUREGERROR

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-ASSERT

3-Error

Assertion '[chars]' failed in [chars] MFIB [0x%08x]: [chars] [chars][chars].

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-4-DISABLING

4-Warning

[chars] MFIB is being disabled due to a fatal error.

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-4-BROKERINVMSG

4-Warning

Invalid message: [chars] type [chars] len [dec]

An invalid message has been received by this broker.

mfib

LOG_STD_ACTION

COMMON_MFIB-3-EPOCH

3-Error

Failed to [chars] table [chars][chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-4-MFIBTABLE

4-Warning

Failed to [chars] table [chars] [chars]

An MFIB table was found to be missing when attempting to perform a change to it. This may be a transient condition

COMMON_MFIB_DDTS_COMPONENT

"If the same table gives repeated warnings or generates more serious" "errors copy the message exactly as it appears and report it to " "your technical support representative"

COMMON_MFIB-4-MFIBMSG

4-Warning

Invalid message received. Type [chars] event/sub-type [dec] length [dec]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-ILLEGAL_TABLEID

3-Error

Attempt to create [chars] table with illegal tableid [dec] [chars]

-

-

-

COMMON_MFIB-3-NO_TABLE_NAME

3-Error

Attempt to clear the name of [chars] table with tableid %p previous name [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-INVALID_AF

3-Error

Invalid address family [dec][chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_MFIB-3-MFIBISSU_REGISTRATION

3-Error

Unable to register [chars] ISSU client[dec].

-

-

-

COMMON_MFIB-3-BG_POPULATE

3-Error

MFIB master background process failed to populate tables for [chars]

COMMON_MFIB_INTERNAL_ERROR

COMMON_MFIB_DDTS_COMPONENT

LOG_STD_ACTION

MFIB_DB-3-LEAKED_OCCUPIED_TABLE

3-Error

%p %p/[chars] as %lu entries %lu ioitems

-

-

-

MFIB_DB-3-LEAKED_TABLE

3-Error

%p %lx due to discard failure

-

-

-

MFIB_DB-3-FREE_FREED_TABLE

3-Error

%p %p/[chars] as %lu entries %lu ioitems

-

-

-

MFIB_DB-6-INVALID_TABLEID

6-Information

Table %p %p/[chars] : [chars]

An internal software error occurred.

-

LOG_STD_ACTION

MFIB_DB-6-MOFRR_ERROR

6-Information

[chars]

An MoFRR internal error occurred.

-

LOG_STD_ACTION

LSP_VIF-2-CHUNK_ERR

2-Critical

Error initializing LSP_VIF chunks

Internal error

-

LOG_STD_NO_ACTION

LSP_VIF-2-RADIX_ERR

2-Critical

Error initializing RADIX tree

The get_fd function reported an error trying to allocate a Event Detector context control block.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMS_FDC_OPEN

7-Debug

[chars]: Failed to open Event Detector context control block

The malloc function reported an error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMS_POLICY_EXEC

7-Debug

[chars]: Policy execution [chars]

An Embedded Event Manager policy requested that the system be reloaded.

ha/eem

""

HA_EM-3-FMS_CNS_FAIL

3-Error

[chars]: Failed to perform CNS action: [chars]

The Embedded Event Manager failed attempting to send a CNS message.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-6-FMS_SWITCH_HARDWARE

6-Information

[chars]: Policy has requested a hardware switchover

An Embedded Event Manager policy requested that a hardware switchover occur.

ha/eem

""

HA_EM-3-FMS_SWITCH_NOT_RF_ACTIVE

3-Error

[chars]: This processor is not in ACTIVE state state = [dec]. Switchover must be performed on ACTIVE processor.

Switchovers must occur on ACTIVE unit not STANDBY unit.

ha/eem

""

HA_EM-7-FMS_SWITCH_FAIL

7-Debug

[chars]: The system is unable to switch to standby processor. Switchover cancelled.

Switchovers must occur when STANDBY is available and ready.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMS_EMPTY_QUEUE

3-Error

[chars]: The I/O queue empty.

The I/O queue is empty at this point and should not be.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMS_ENQUEUE_FAIL

3-Error

[chars]: The Unable to enqueue packet onto queue.

The queue is not in a state to handle enqueues.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMS_QUEUE_INIT

3-Error

[chars]: The Unable to initialize queue.

An attempt to publish an event failed because there is no more room in the publish queue.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMS_POLICY_LOOKUP_FAIL

3-Error

[chars]: Failed to look up in the table the registration specification for policy [chars].

The realloc function reported an error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMS_INV_ARG_STRING

7-Debug

[chars]: Invalid argument string: [chars]

The fh_hash_md5_fd function reported the specified error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMS_POLICY_CHECKSUM

3-Error

[chars]: Checksum error for policy [chars] - this policy will not be run

The checksum computed for the specified policy does not match the original checksum computed when the policy was registered.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-6-FMS_MODIFY_POLICY

6-Information

[chars]: unable to modify the policy to class [chars]: scheduling rule unavailable.

There is no scheduler rule configured to service this event class.

ha/eem

"Please configure a scheduler rule before modifying the event."

HA_EM-6-FMS_RUNNING_POLICY

6-Information

[chars]: cannot [chars] a running policy with jobid [dec].

Embedded Event Manager Scheduler Command cannot change a running policy.

ha/eem

"The command is not applicable to a running policy."

HA_EM-6-FMS_LAST_POLICY

6-Information

[chars]: Cannot change a class [chars] [chars] to priority LAST. LAST is for default policies only

Embedded Event Manager Scheduler Command can only change a default policy to priority LAST.

ha/eem

"The command is applicable to default policies only."

HA_EM-6-FMS_MODIFY_LAST_POLICY

6-Information

[chars]: Cannot modify a LAST policy to class [chars]. LAST policies are for class default only.

Embedded Event Manager LAST policy is for default class only.

ha/eem

"The command is applicable to default policies only."

HA_EM-3-FMS_NO_TRACK

3-Error

Use of the \track\ keyword in the correlate statement is not supported in this image.

The Embedded Event Manager Track ED is not supported in this image.

ha/eem

"Track ED is not available in this image"

HA_EM-4-FMS_NO_SCHED_THREAD

4-Warning

No threads are configured to service event class [chars]

The Embedded Event Manager has no scheduler threads to service this event class.

ha/eem

"Configure threads for the event class using the 'event manager scheduler' command."

HA_EM-4-FMPD_EVENT_CREATE

4-Warning

[chars]: failed to create an event: [chars]

Failed to create an Embedded Event Manager event.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-4-FMPD_EVENT_REG

4-Warning

[chars]: failed to register an event: [chars]

Failed to register an Embedded Event Manager event.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-4-FMPD_IPC_GET_PAK

4-Warning

[chars]: failed to allocate an IPC buffer

Embedded Event Manager failed to allocate a buffer from IPC.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_IPC_PORT_CREATE

3-Error

[chars]: failed to create an IPC port: [chars]

Embedded Event Manager failed to create an IPC port.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_IPC_PORT_OPEN

3-Error

[chars]: failed to open an IPC port: [chars]

Embedded Event Manager failed to open an IPC port.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_IPC_PORT_REGISTER

3-Error

[chars]: failed to register an IPC port: [chars]

Embedded Event Manager failed to register an IPC port.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-4-FMPD_IPC_SEND_MSG

4-Warning

[chars]: failed to send an IPC message: [chars]

Embedded Event Manager failed to send a message through IPC.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMPD_EVENT_TYPE

7-Debug

[chars]: unknown event type [dec]

An unknown Embedded Event Manager even type was detected.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_FH_INIT

3-Error

[chars]: could not initialize Embedded Event Manager service: [chars]

An internal error was detected when initializing Embedded Event Manager service.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_QUEUE_INIT

3-Error

[chars]: could not initialize queue

An internal error was detected when initializing Embedded Event Manager queue.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMPD_LAST_POLICY

7-Debug

[chars]: invalid last policy name replied [chars]

Internal error. The last policy name the script director replied to show fm policy registered command is an invalid policy name.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMPD_NO_MEM

7-Debug

[chars]: not enough memory: [chars]

Allocating memory failed due to a low-memory condition.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_REQINFO

3-Error

[chars]: Error attempting to fetch event information: [chars].

The Embedded Event Manager Policy Director failed to receive event info for a callback.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_NOESID

3-Error

[chars]: No such event spec id found.

The Embedded Event Manager Policy Director could not find the event for the event spec. ID.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_NOEID

3-Error

[chars]: No such event id found.

An internal software error occurred.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_WRONGTYPE

3-Error

[chars]: Published event type does not match event spec.

The Embedded Event Manager Policy Director detected a mis-match in event type between the published event and the event spec.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_ACTION

3-Error

[chars]: Error occurred while performing action: [chars].

The Embedded Event Manager Policy Director failed to perform an action for the registered event.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_ACTION_INFO

3-Error

[chars]: Error occurred while fetching action information: [dec].

The Embedded Event Manager applet attempted to set the state of a tracking object that does not exist.

ha/eem

"Only set the state of tracking objects that have already been " "configured in the system. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative."

HA_EM-3-FMPD_SET_INFO

3-Error

[chars]: Error occurred while fetching variable information: [dec].

The Embedded Event Manager Policy Director was unable to set the variable with the requested information.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_UNKNOWNTYPE

3-Error

[chars]: Unknown event type found in applet.

The Embedded Event Manager applet had an unknown event type.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_UNKNOWN_ENV

3-Error

[chars]: could not find environment variable: [chars]

The Embedded Event Manager policy director could not find the environment variable specified in the action message.

ha/eem

"Only use well known Embedded Event Manager environment variables. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative."

HA_EM-3-FMPD_ERROR

3-Error

Error executing applet [chars] statement [chars]

The Embedded Event Manager policy director found an error when processing an applet.

ha/eem

"Check syntax of applet statement. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative."

HA_EM-3-FMPD_EXECUTE_CALLBACK

3-Error

[chars]: failed to execute callback

Failed to execute callback routine.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-4-FMPD_NO_EVENT

4-Warning

No event configured for applet [chars]

No event has been configured for this applet.

ha/eem

"Configure an event for this applet."

HA_EM-3-FMPD_SMTP

3-Error

Error occurred when sending mail to SMTP server: [chars] : [chars]

An unexpected error occurred when sending mail to SMTP server.

ha/eem

""

HA_EM-3-FMPD_SMTP_SEND

3-Error

Unable to send notification using all SMTP servers

An unexpected error occurred when sending mail to all SMTP servers.

ha/eem

""

HA_EM-3-FMPD_CLI_READ

3-Error

Unable to read CLI response: [chars]

Unable to read CLI response.

ha/eem

""

HA_EM-3-FMPD_CLI_WRITE

3-Error

Unable to send CLI command: [chars]

Unable to send CLI command.

ha/eem

""

HA_EM-3-FMPD_CLI_CONNECT

3-Error

Unable to establish CLI session: [chars]

Unable to establish CLI session.

ha/eem

""

HA_EM-3-FMPD_CLI_DISCONNECT

3-Error

Error disconnecting from CLI session: [chars]

An error occurred while disconnecting from the CLI session.

ha/eem

""

HA_EM-3-FMPD_CLI_NOTTY

3-Error

Error attempting to access an unopened CLI session: [chars]

An error occurred attempting to access an unopened CLI session: [chars]

ha/eem

""

HA_EM-4-FMPD_NO_ACTION

4-Warning

No action configured for applet [chars]

No action has been configured for this applet.

ha/eem

"Configure at least one action for this applet."

HA_EM-7-FMPD_FORMAT_TIME

7-Debug

[chars]: error attemting to format time string

Format time failure.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_CHECKSUM_MISMATCH

3-Error

[chars]: file checksum mismatch

The checksum value of an installed policy does not match the value provided by the installation manager.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_PROCESS_XML

3-Error

[chars]: error processing xml buffer

An error occurred processing the event publish information xml buffer.

ha/eem

"Copy the message exactly as it appears and report it your technical\n\ support representative."

HA_EM-4-FMPD_NOTAGNAME

4-Warning

[chars]: No tag [chars] found corresponding to this event publish.

The Embedded Event Manager policy director could not associate the tagname with a published event.

ha/eem

"Only use tagnames in the action info type event reqinfo command which correspond to the published event."

HA_EM-6-FMPD_UPDATE_POLICY_COPY

6-Information

Policy update has copied [dec] bytes from [chars] to [chars]

An EEM policy has been copied as a result of an event manager update command

ha/eem

""

HA_EM-6-FMPD_UPDATE_POLICY_REGISTER

6-Information

Policy update has successfully re-registered policy [chars]

An EEM policy has been successfully re-registered as a result of an event manager update command

ha/eem

""

HA_EM-6-FMPD_UPDATE_POLICY_UNREGISTER_FAIL

6-Information

Policy update has failed to unregister policy [chars] [chars]

An EEM policy has failed to be unregistered as a result of an event manager update command

ha/eem

""

HA_EM-6-FMPD_UPDATE_POLICY_REGISTER_FAIL

6-Information

Policy update has failed to register policy [chars] [chars]

An EEM policy has failed to be registered as a result of an event manager update command

ha/eem

""

HA_EM-6-FMPD_REGCOMP

6-Information

Error compiling regular expression: [chars]

An error was encountered when compiling the given regular expression.

ha/eem

"Check syntax of regular expression pattern. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative."

HA_EM-6-FMPD_CONTEXT_SAVE

6-Information

Failed to save variable context for key [chars]: [chars]

Failed to context save variable information for event.

ha/eem

"Ensure context information with the same key is not already saved. " "If the message continues to occur copy the message exactly as it appears " "and report it your technical support representative."

HA_EM-6-FMPD_CONTEXT_RETRIEVE

6-Information

Failed to retrieve context for key [chars]: [chars]

Failed to context retrieve variable information for event.

ha/eem

"Ensure context information with the given key is saved. " "If the message continues to occur copy the message exactly as it appears " "and report it your technical support representative."

HA_EM-6-FMPD_OPERAND_INVALID

6-Information

Invalid operand in action expected value within range %ld to %ld received: [chars]

Arithmetic actions only accept valid long integer values.

ha/eem

"Ensure value provided to action is long integer."

HA_EM-6-FMPD_DIVIDE_ZERO

6-Information

Invalid operand in arithmetic division cannot divide by zero

Arithmetic division does not allow divide by zero.

ha/eem

"Ensure denominator provided to division action is non-zero."

HA_EM-7-FMFD_DE_FETCH

7-Debug

[chars]: [chars][[dec]]

Internal error. The event detector has failed to fetch a data element from the statistics data engine.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_HIST_QERR

7-Debug

[chars]

Internal error. The event detector has failed to get a free history list entry.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_INV_COMPARE_OP

7-Debug

[chars]: invalid comparison operator: [dec]

Internal error. The value comparison operator is invalid or not supported.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_INV_STATS_TYPE

7-Debug

[chars]: invalid statistics value type: [dec]

Internal error. The statistics data type is invalid or not supported.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_INV_TM

7-Debug

[chars]: invalid timer: type=[dec] timer=%p

Internal error. The timer value is invalid or not as expected.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_INV_TM_TYPE

7-Debug

[chars]: invalid timer type: [dec]

Internal error. The timer type is invalid or not supported.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_MSGSEND_RETRY_ERR

7-Debug

[chars]: [dec]

The event detector has exceeded its maximum number of retries to send a pulse to the embedded event manager to notify of an event publish.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_OE_CREATE

7-Debug

[chars]: could not create an occurrence entry

Internal error. The event detector has failed to create an entry for the matched occurrence list.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_OE_REMOVE

7-Debug

[chars]: could not remove an occurrence entry

Internal error. The event detector has failed to remove an entry for the matched occurrence list.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_PUB_TM_ALLOC

7-Debug

[chars]: Unable to allocate memory for event publish timer block

Internal error. The event detector has failed to allocate memory for the event publish timer block.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMFD_TTY_NUM

3-Error

[chars]: Error occurred while fetching TTY number.

The Embedded Event Manager failed to fetch a TTY number.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_TM_LEAF_NEW

7-Debug

[chars]: could not create a leaf timer

Internal error. The event detector has failed to create a managed leaf timer.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_MET_RBLD

7-Debug

[chars]: [chars]

Internal error. The event detector has failed to rebuild the metric list from the checkpointed records.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMFD_OID_UNAVAIL

3-Error

[chars]: The following oid has become unavailable: [chars]

The enqueue function reported an error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMFD_EMPTY_QUEUE

3-Error

[chars]: The [chars] event detector I/O queue empty.

The SNMP message failed to be created

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_VARBIND_FAIL

7-Debug

[chars]: Unable to create a SNMP varbind

The oid failed to make into a SNMP varbind

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_OID_INVALID

7-Debug

[chars]: Invalid SNMP oid length [dec]

The SNMP oid has invalid length

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_UNKNOWN_TYPE

7-Debug

[chars]: Unknown SNMP operation or response type [dec]

The operation or response type is unknown.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_ADDR_ILLEGAL

7-Debug

[chars]: Illegal SNMP address type

The SNMP address is illegal.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_ADDR_IPV6

7-Debug

[chars]: SNMP IPV6 address is not supported

The IPV6 address is not supported.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_RESP_TIMEOUT

7-Debug

[chars]: SNMP response has timed out

The SNMP response has error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_RESP_CANCEL

7-Debug

[chars]: SNMP response cancelled

The SNMP response has been cancelled.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_RESP_Q_EMPTY

7-Debug

[chars]: SNMP proxy exec got event but queue is empty

The SNMP proxy got event but the queue is empty.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_REQ_FAILED

7-Debug

[chars]: SNMP request failed

The SNMP request has failed.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_MAKE_PDU_FAILED

7-Debug

[chars]: SNMP make pdu failed

The SNMP pdu make has failed.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_BUILD_PDU_FAILED

7-Debug

[chars]: SNMP build pdu failed

The SNMP pdu build has failed.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMFD_SNMP_ERRCODE

7-Debug

[chars]: [chars]

The SNMP error code.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMPD_NO_PROC

3-Error

[chars]: Failed to create process

The process create function reports an error

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-6-FMPD_EEM_CONFIG

6-Information

[chars]: [chars]

The Embedded Event Manager reports an error on Event Manager configuration

ha/eem

"Check the EEM applet or policy configuration"

HA_EM-6-FMPD_SNMP_VARS_EXCEEDED

6-Information

[chars]: number of values exceeded [dec]

The number of values per variable exceeded the maximum

ha/eem

"Check the EEM applet or policy configuration"

HA_EM-6-FMPD_SNMP_DUP_OID

6-Information

[chars]: duplicate oid

The oid is a duplicate

ha/eem

"Check the EEM applet or policy configuration"

HA_EM-6-FMPD_SNMP_NO_VAR

6-Information

[chars]: No variable [chars]

The variable is not defined.

ha/eem

"Check the EEM applet or policy configuration"

HA_EM-6-FMPD_SNMP_TRAPVAR_ADD

6-Information

[chars]: Error adding trapvar to queue [chars]

The trap variable was not added to the queue.

ha/eem

"Check the EEM applet or policy configuration"

HA_EM-6-FMPD_SWITCH_HARDWARE

6-Information

[chars]: Policy has requested a hardware switchover

An Embedded Event Manager policy requested that a hardware switchover occur.

ha/eem

"None"

HA_EM-7-FMPD_SWITCH_FAIL

7-Debug

[chars]: The system is unable to switch to standby processor. Switchover cancelled.

Switchovers must occur when STANDBY is available and ready.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMC_REG_CBH_PULSE

7-Debug

[chars]: Unable to locate reg callback entry for pulse code [dec]

The registration callback handler was unable to validate the pulse code received.

ha/eem

"The pthread_create function reported an error."

HA_EM-7-FMC_REG_CBH_SEND

7-Debug

[chars]: Unable to send response for FH_MSG_CALLBACK_DONE [chars]

The registration callback handler was unable to send the FH_MSG_CALLBACK_DONE message to the Embedded Event Manager Server.

ha/eem

"The pthread_create function reported an error."

HA_EM-7-FMC_INV_REPLY

7-Debug

[chars]: Application client library unable to handle message receive.

The CNS Action process failed to set the restart callback.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-ACTION_CNS_OPEN_FAIL

3-Error

[chars]: Unable to open connection to CNS Event Agent: [dec]

The CNS Action process failed to open CNS handle to Event Agent.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-ACTION_CNS_AGENT_UNAVAIL

7-Debug

[chars]: CNS Event Agent not available: [dec]

The enqueue function reported an error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-ACTION_WB_CREATE

7-Debug

[chars]: create_watched_boolean failed: [chars]

The create_watched_boolean function reported an error trying to create the watched boolean.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-ACTION_WB_DELETE

7-Debug

[chars]: delete_watched_boolean failed: [chars]

The delete_watched_boolean function reported an error trying to delete the watched boolean.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMC_CBH_PROCESS_CREATE

3-Error

[chars]: callback handler process create failed for eid: [dec]

The process_create function reported an error trying to create the callback handler process.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMC_FH_INIT

3-Error

[chars]: fh_init failed : [dec]

The strdup function reported an error.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-7-FMS_NULL_SCRIPT_NAME

7-Debug

[chars]: The script name is NULL

An invalid script name was passed as an argument into the specified function.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-4-FMPD_DSIG_TYPE_CHANGE

4-Warning

Cisco Signature not found or invalid. [chars] has been registered as a user policy.

Cisco Signature not found or invalid.

ha/eem

"Sign with Cisco signature."

HA_EM-3-FMFD_SNMP_MIB_OBJ_REP_FAIL

3-Error

[chars]: SNMP MIB object info replace failed [dec]

The SNMP MIB object info replace function has failed.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-4-FMFD_SNMP_NO_OBJECT_VALUE

4-Warning

[chars]: SNMP MIB object value not provided

The SNMP MIB object value is not provided for substitution.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

HA_EM-3-FMFD_SNMP_OBJECT_UNKNOWN_RESPONSE_CODE

3-Error

[chars]: Unknown SNMP object response code [dec]

The SNMP MIB object response code is unknown.

ha/eem

"Copy the message exactly as it appears and report it your technical " "support representative."

DSMIBPROV-3-CLASSNOTFOUND

3-Error

class: [chars] is not present in db.

This is a configuration error for dsmib.It indicates that dsmib shim does not get the notification when the classmap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations.Capture the log in the console with class name for any possible debugging.

dsmib

"LOG_STD_ACTION"

DSMIBPROV-3-POLICYNOTFOUND

3-Error

policy: [chars] is not present in db.

This is a configuration error for dsmib.It indicates that dsmib shim does not get the notification when the policymap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations.Capture the log in the console with policy name for any possible debugging.

dsmib

"LOG_STD_ACTION"

DSMIBPROV-6-UNSUPPORTED

6-Information

[chars]

This is a provisioning error for dsmib. It indicates that dsmib does not support the configuration entered. See the error message printed out on the console for possible supported configurations.Then try with different configurations valid for dsmib.

dsmib

"LOG_STD_NO_ACTION"

DSMIBPROV-3-XMIT_CONF

3-Error

[chars]

The configuration is not transmitted properly from shim. This indicates that the operation to transmit the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim.

dsmib

"LOG_STD_ACTION"

DSMIBPROV-6-UNSUPPORTED

6-Information

[chars]

This is a provisioning error for dsmib. It indicates that dsmib does not support the configuration entered. See the error message printed out on the console for possible supported configurations. Then try with different configurations valid for dsmib.

-

LOG_STD_NO_ACTION

DSMIBPROV-3-POLICYNOTFOUND

3-Error

policy: [chars] is not present in db.

This is a configuration error for dsmib. It indicates that dsmib shim does not get the notification when the policymap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations. Capture the log in the console with policy name for any possible debugging.

dsmib

LOG_STD_ACTION

DSMIBPROV-3-CLASSNOTFOUND

3-Error

class: [chars] is not present in db.

This is a configuration error for dsmib. It indicates that dsmib shim does not get the notification when the classmap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations. Capture the log in the console with class name for any possible debugging.

dsmib

LOG_STD_ACTION

DSMIB-3-XMIT_CONF

3-Error

[chars]

The configuration is not transmitted properly from shim. This indicates that the operation to transmit the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim.

dsmib

LOG_STD_ACTION

DSMIB-3-CLIENT_TYPE

3-Error

Type [dec] is invalid for collision [chars]

The specified type of client is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error.

dsmib

"LOG_STD_ACTION"

DSMIB-3-RECV_CONF

3-Error

Error receiving configuration in DSMIB.

The configuration is not received properly from shim. This indicates that the operation to receive the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim.

dsmib

"LOG_STD_ACTION"

DSMIB-3-RECV_STAT

3-Error

Error in decoding statistics in DSMIB.

The counters are not received properly from shim. This indicates that the operation to receive the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib.

dsmib

"LOG_STD_ACTION"

DSMIB-3-TIMER_START

3-Error

[chars]

This indicates that the operation to start/restart a timer has failed. This condition will result in counters out-of-sync between MQC and dsmib.

dsmib

"LOG_STD_ACTION"

DSMIB-3-UID_DELETE

3-Error

[chars] unable to remove index %08X

The specified entity is unable to removed the specified index. This is an internal software error.

dsmib

"LOG_STD_ACTION"

DSMIB-3-UID_EXISTS

3-Error

[chars] attempt to add index %08X [chars]

The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error.

dsmib

"LOG_STD_SH_CMD_ACTIONshow dsmib db id"

DSMIB-3-WRED_PARENT

3-Error

There is a child policy under class [chars] in policy-map [chars] where random-detect is configured which is not supported while diffservmib RFC 2475 is enabled

Random-detect is not supported in parent class of a HQOS policy when diffservmib RFC 2475 is enabled

dsmib

"LOG_STD_ACTION"

DSMIB-3-XMIT_MSG

3-Error

[chars]

The IPC message was not transmitted. This condition will result in counters out-of-sync between MQC and dsmib or some config being out of sync.

dsmib

"LOG_STD_ACTION"

DSMIB-3-XMIT_STAT

3-Error

Error in statistics query and encoding in DSMIB.

The counters are not encoded and transmitted properly from shim. This indicates that the operation to encode the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib.

dsmib

"LOG_STD_ACTION"

DSMIB-3-CLIENT_TYPE

3-Error

Type [dec] is invalid for collision [chars]

The specified type of client is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error.

dsmib

LOG_STD_ACTION

DSMIB-3-UID_EXISTS

3-Error

[chars] attempt to add index %08X [chars]

The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error.

dsmib

"show dsmib db id"

DSMIB-3-UID_DELETE

3-Error

[chars] unable to remove index %08X

The specified entity is unable to removed the specified index. This is an internal software error.

dsmib

LOG_STD_ACTION

DSMIB-3-RECV_CONF

3-Error

Error receiving configuration in DSMIB.

The configuration is not received properly from shim. This indicates that the operation to receive the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim.

dsmib

LOG_STD_ACTION

DSMIB-3-RECV_STAT

3-Error

Error in decoding statistics in DSMIB.

The counters are not received properly from shim. This indicates that the operation to receive the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib.

dsmib

LOG_STD_ACTION

DSMIB-3-TIMER_START

3-Error

[chars]

This indicates that the operation to start/restart a timer has failed. This condition will result in counters out-of-sync between MQC and dsmib.

dsmib

LOG_STD_ACTION

DSMIB-3-XMIT_STAT

3-Error

Error in statistics query and encoding in DSMIB.

The counters are not encoded and transmitted properly from shim. This indicates that the operation to encode the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib.

dsmib

LOG_STD_ACTION

DSMIB-3-XMIT_MSG

3-Error

[chars]

The IPC message was not transmitted. This condition will result in counters out-of-sync between MQC and dsmib or some config being out of sync.

dsmib

LOG_STD_ACTION

DSMIB-3-WRED_PARENT

3-Error

There is a child policy under class [chars] in policy-map [chars] where random-detect is configured which is not supported while diffservmib RFC 2475 is enabled

Random-detect is not supported in parent class of a HQOS policy when diffservmib RFC 2475 is enabled

dsmib

LOG_STD_ACTION

PRP-4-NOMEM

4-Warning

Not enough memory available for [chars]

The PRP could not obtain the memory it needed.

prp

LOG_STD_SH_TECH_ACTION

ISSU_ERROR-3-MSG_NOT_OK

3-Error

[chars][dec]: ISSU message type [dec] is not compatible

ISSU received a message not compatible with the running version.

ISSU_CLIENT_COMP

"show message type <Client_ID>"

ISSU_ERROR-3-MSG_MTU

3-Error

[chars][dec]: Client failed to get mtu for message [dec] [chars]

[chars][dec]: client cannot get the MTU for a message type

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-TRANSFORM_FAILED

3-Error

[chars][dec]: [chars] transformation failed [chars]

The transformation operation for the ISSU message has failed

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-TRANSFORM_FAILED_DETAILED

3-Error

[chars][dec]: [chars] transformation failed for message [dec] endpoint [dec] [chars]

The transformation operation for the ISSU message has failed

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CF_SEND

3-Error

[chars][dec]: Client failed to send message [dec]

ISSU client cannot send a negotiation message to a peer

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-ICC_SEND

3-Error

[chars][dec]: Client failed to send message

ISSU client cannot send a negotiation message to a peer

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CLIENT_REG

3-Error

[chars][dec]: Client failed to register [chars]

The ISSU Client could not be registered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CLIENT_REG_FAILED

3-Error

[chars][dec]: Client is not

The ISSU Client is not yet initialized. The negotiation for this client is not yet done.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-SESSION_REG

3-Error

[chars][dec]: session failed to register [chars]

The client's ISSU session could not be registered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-SESSION_UNREG

3-Error

[chars][dec]: session [dec]

The client's ISSU session could not be unregistered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-START_NEGO_FAILED

3-Error

[chars][dec]: failed to

The ISSU client cannot start its negotiation

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CAPTYPE_REG

3-Error

[chars][dec]: failed to

The ISSU client failed to register a capability type

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CAPENTRY_REG

3-Error

[chars][dec]: failed to register a capability entry [chars]

The ISSU client failed to register a capability entry

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CAPGROUP_REG

3-Error

[chars][dec]: failed to register a capability group [chars]

The ISSU client failed to register a capability group

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-MSGTYPE_REG

3-Error

[chars][dec]: failed to register a message type [chars]

The ISSU client failed to register a message type

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-MSGGROUP_REG

3-Error

[chars][dec]: failed to

The ISSU client failed to register a message group

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-ENTITY_REG

3-Error

[chars][dec]: failed to register

The ISSU entity could not be registered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-ENTITY_UNREG

3-Error

[chars][dec]: failed to unregister

The ISSU entity could not be unregistered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CAP_REG

3-Error

[chars][dec]: failed to register

The capabilities of the ISSU client could not be registered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-MSG_REG

3-Error

[chars][dec]: failed to register its messages [chars]

Messages for the ISSU client could not be registered

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-CAP_EXCHANGE

3-Error

[chars][dec]: Capability exchange failed with error [chars]

The capability exchange failed the ISSU client is unable to process the received capability

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-NEGO_PROCESS

3-Error

[chars][dec]: Cannot create process: [chars]

The process to negotiate the session for the specified ISSU client cannot be created.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-MTU_NOT_ENOUGH

3-Error

[chars][dec]: Requested buffer size [dec] is greater than the max MTU size

Checkpoint buffer size requested is greater than the max MTU size checkpoint supports

cat6000-ha

LOG_STD_ACTION

ISSU_ERROR-3-MSG_POLICY

3-Error

[chars][dec]: Client failed to negotiate version for message type [dec] error [chars]

ISSU client cannot negotiate message to a peer

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-2-NEGO_NOT_DONE

2-Critical

[chars][dec]: ISSU Negotiation not complete

Unable to complete ISSU negotiation.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-2-NTI_REG

2-Critical

[chars][dec]: Failed to register with

Could not register client with NTI.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-2-NTI_UNREG

2-Critical

[chars][dec]:

Could not unregister client with NTI.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-2-NTI_EP_TYPE_REG

2-Critical

[chars][dec]:

Client could not register endpoint type with NTI.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-2-NTI_EP_TYPE_UNREG

2-Critical

[chars][dec]:

Client could not unregister endpoint type with NTI.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-2-CLIENT_INCOMPATIBLE

2-Critical

[chars][dec]: ISSU Client

ISSU Client incompatible.

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU_ERROR-3-REG_ARBITRATE_CALLBACK

3-Error

[chars][dec]:

-

ISSU_CLIENT_COMP

LOG_STD_ACTION

ISSU-3-DUP_REG_ENDPOINT

3-Error

Endpoint is registered already.

Endpoint is registered already.

ha-issu-infra

"'show issu endpoint' to check if ISSU subsystem \n\is initialized twice."

ISSU-3-DUP_REG_UNDER_ENDPOINT

3-Error

[chars][dec] is registered already under endpoint.

Item is registered already under endpoint.

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported item is registered already if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-SET_UNKNOWN_UID

3-Error

Unknown unique_id is set.

Platform team should provide distinctive identifier for endpoint.

ha-issu-infra

"Copy the error and send it to TAC. \n\TAC team can contact platform team to provide distinctive identifier \n\for endpoint"

ISSU-3-FAILED_TO_INIT_ISSU_PROTO

3-Error

Failed to initialize ISSU proto.

Failed to initialize ISSU proto.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why ISSU protocol can not initialize correctly"

ISSU-3-FAILED_TO_CREATE_ID32_SPACE

3-Error

Failed to create ID32 space.

Failed to create ID32 space.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-NON_ISSU_ID_UNDER_ENDPOINT

3-Error

Non ISSU [chars]

Peer endpoint does not support ISSU

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why non-issu ID is used"

ISSU-3-UNKNOWN_ID_UNDER_ENDPOINT

3-Error

Can not use unknown [chars].

Can not use unknown id.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why unknown ID is used"

ISSU-3-FAILED_TO_ALLOC_UNDER_ENDPOINT

3-Error

Can not allocate [chars] [chars][dec] control block.

Can not allocate control block.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. 'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\if client problem reported. Otherwise contact ISSU infrastructure team instead"

ISSU-3-FAILED_TO_ALLOC_FUNCT_UNDER_ENDPOINT

3-Error

Can not allocate [chars][dec] [chars].

Can not allocate function callback.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. 'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\if client problem reported. Otherwise contact ISSU infrastructure team instead"

ISSU-3-NOT_FIND_UNDER_ENDPOINT

3-Error

Can not find [chars]0x[hec] control block under endpoint.

-

-

-

ISSU-3-EMPTY_UNDER_ENDPOINT

3-Error

[chars] is empty under endpoint.

Item is empty under endpoint.

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is empty if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-EMPTY_UNDER_CLIENT

3-Error

[chars] is empty under client [chars][dec].

Item is empty in client.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported item under client is empty"

ISSU-3-EMPTY_UNDER_ENTITY

3-Error

[chars] is empty [chars] under client [chars][dec] and entity[dec].

-

-

-

ISSU-3-NOT_DUMY_CAP_TYPE

3-Error

Cap type[dec] is not dumy one.

Cap type is not dumy one.

ha-issu-infra

"'show issu cap type | include <cap type>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why dummy cap type is not used"

ISSU-3-FAILED_TO_UNREG_SES

3-Error

Failed to unregister [chars] session under client [chars][dec] and

Failed to unregister session.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-ENDPOINT_NOT_REG

3-Error

Endpoint is not registered yet.

Endpoint is not registered yet.

ha-issu-infra

"Copy the error and send it to TAC. \n\TAC team can contact ISSU infrastruture team to check why endpoint is not registered"

ISSU-3-NOT_REG_UNDER_ENDPOINT

3-Error

[chars][dec] is not registered under endpoint.

Item is not registered under endpoint.

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is not registered if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-CLIENT_OR_ENTITY_NOT_REG

3-Error

Client [chars][dec] or entity[dec] is not registered [chars].

-

-

-

ISSU-3-NOT_REG_UNDER_ENTITY

3-Error

[chars][dec] is not registered under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-NULL_CALLBACK_UNDER_ENTITY

3-Error

[chars] callback is NULL for msg session registration under client [chars][dec] and entity[dec]

Callback is NULL for msg session registration.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported callback is NULL"

ISSU-3-FAILED_TO_ALLOC_CHUNK_MEMORY

3-Error

chunk allocation for [chars] failed.

Chunk malloc failed.

ha-issu-infra

"copy the error and send it to TAC. TAC team can \n\contact ISSU client team"

ISSU-3-FAILED_TO_ALLOC_MEMORY

3-Error

memory allocation for [chars] failed.

malloc failed.

ha-issu-infra

"copy the error and send it to TAC. TAC team can \n\contact ISSU client team"

ISSU-3-FAILED_TO_ALLOC_ENTITY

3-Error

Can not allocate entity[dec] under client [chars][dec]

Can not allocate entity control block under client.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-FAILED_TO_ALLOC_FUNCT_UNDER_ENTITY

3-Error

Can not allocate [chars] under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-FAILED_TO_ALLOC_UNDER_ENTITY

3-Error

Can not allocate [chars][dec] under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-FAILED_TO_ALLOC_UNDER_GROUP

3-Error

Can not allocate [chars][dec] for [chars][dec] registration under client

Can not allocate item for group registration under client and entity.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-FAILED_TO_ALLOC_UNDER_MSG_SES

3-Error

Can not allocate [chars] for msg session[dec] registration under

Can not allocate control block for msg session registration.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-NULL_CALLBACK_UNDER_ENDPOINT

3-Error

[chars] callback is NULL for registration.

Callback is NULL for registration

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported callback is NULL if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-NULL_CALLBACK_UNDER_SESSION

3-Error

Can not register null [chars] callback in [chars] session[dec].

-

-

-

ISSU-3-MISSING_ITEM_IN_REG

3-Error

[chars][dec] is not available [chars] under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-DUP_ENTITY_REG

3-Error

Entity[dec] is registered already under client [chars][dec]

-

-

-

ISSU-3-DUP_ITEM_IN_REG_UNDER_ENTITY

3-Error

[chars] is duplicated [chars] under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-DUP_REG_UNDER_ENTITY

3-Error

[chars][dec] is registered already under client [chars][dec] and

Item is registered already under client and entity.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported items under entity is registered already"

ISSU-3-NOT_FIND_UNDER_ENTITY

3-Error

Can not find [chars][dec] control block under client [chars][dec] and

Can not find control block under client and entity.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control blcok can not be found"

ISSU-3-NOT_FIND_MSG_SES

3-Error

Can not find message session[dec] [chars].

-

-

-

ISSU-3-NOT_FIND_FUNCT_UNDER_SESSION

3-Error

Can not find [chars] under [chars] session[dec].

Can not find function under session.

ha-issu-infra

"'show issu session | include <session id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control block under session can not be found"

ISSU-3-NOT_FIND_UNDER_SESSION

3-Error

Can not find [chars][dec] under [chars] session[dec].

Can not find item under session.

ha-issu-infra

"'show issu session | include <session id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control block under session can not be found"

ISSU-3-DUMY_ENTRY_NOT_LAST

3-Error

Dumy cap entry is not last one for cap group[dec] registration

Dumy cap entry is not last one for cap group registration

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why dumy entry is not last one during registration"

ISSU-3-INVALID_ITEM_UNDER_ENDPOINT

3-Error

Invalid [chars] under endpoint

Invalid item under endpoint

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why invalid item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-INVALID_PARAM_UNDER_SES

3-Error

Invalid params [chars] under session[dec]

Invalid parameters under session

ha-issu-infra

"'show issu session | include <session id>' \n\to find out which client's session is causing this error msg. \n\copy the error and send it to TAC. TAC team can contact ISSU team to \n\check why invalid params is used if problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-UNKNOWN_ENTITY_ID

3-Error

Unknown entity id under client [chars][dec]

Unknown entity id under client

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why unknown entity id is used during registration"

ISSU-3-UNKNOWN_DOMAIN_ID

3-Error

Unknown domain id [dec] under client [chars][dec] entity [dec]

-

-

-

ISSU-3-INVALID_ITEM_UNDER_ENTITY

3-Error

Invalid [chars] under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-UNKNOWN_ID_UNDER_ENTITY

3-Error

Unknown [chars] under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-VERSION_OUT_OF_RANGE

3-Error

Msg version[dec][dec] is out of range for msg[dec] under client

Msg version is out of range for group registration.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why version is out of range for group registration"

ISSU-3-INVALID_VERSION_LOWHIGH

3-Error

Invalid low[dec] and high[dec] value for msg[dec] under client

Invalid low and high value for group registration.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why invalid low or high version is used for group registration"

ISSU-3-VERSION_LOWHIGH_NOT_MATCH_TABLE_SIZE

3-Error

Version low[dec] and high[dec] value for msg[dec] does not

Version low and high value for msg does not match table size.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why low/high version is not macth table size for msg registration"

ISSU-3-VERSION_OUT_OF_ORDER

3-Error

Msg version[dec][dec] is out of order for msg[dec] under client

Msg version is out of order for group registration.

ha-issu-infra

"'show issu client | include <client id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why version is out of order for msg registration"

ISSU-3-FAILED_TO_ALLOC_UNDER_MSG

3-Error

Can not allocate [chars] for msg [dec] registration under client

Can not allocate control block for msg registration.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-IN_USE_UNDER_ENTITY

3-Error

[chars][dec] is in use under client [chars][dec] and entity[dec]

-

-

-

ISSU-3-IN_USE_UNDER_ENDPOINT

3-Error

[chars][dec] is in use under endpoint

Item is in use under endpoint.

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-4-NEGO_NOT_FINISHED

4-Warning

Negotiation is not finished for client [chars][dec] msg session[dec].

-

-

-

ISSU-4-MSG_INCOMP

4-Warning

Message[dec] is incompatible under msg session[dec].

-

-

-

ISSU-3-FSM_INIT

3-Error

Fail to create process during FSM init.

The creation of FSM timer process fails.

ha-issu-infra

"User should check system resource during bootup\n\ time."

ISSU-4-FSM_INCOMP

4-Warning

Version of local ISSU client [chars][dec] in session [dec] is

The protocol versions of the local and remote clients are\n\ incompatible. These clients can not communicate with each\n\ other.

ha-issu-infra

"Use 'show version' and 'show issu clients' to help\n\ verify that the software images are incompatible. Upgrade\n\ the software images on each unit to versions that are \n\ compatible. " LOG_STD_RECUR_ACTION

ISSU-3-FSM_BADMSG

3-Error

Peer session [dec] while receiving message [chars] is wrong.

Session are mismatched on peers or not found.

ha-issu-infra

"'show issu session | include <session id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to make sure that receiving path uses correct session id."

ISSU-3-MSG_SES_IN_MSG_NOT_FOUND

3-Error

The intended session [dec] specified in received [chars] for client [chars][dec] is not found.

Cannot find the session with the session id\n\ specified in the received message.

ha-issu-infra

"'show issu session | include <session id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to make sure that receiving path uses correct session id."

ISSU-3-FSM_DUP_UID

3-Error

Duplicate unique_id on session [dec]: my_uid [dec] peer_uid [dec].

Violate the requirement that each endpoint must have distinctive \n\ identifier.

ha-issu-infra

"Copy the error and send it to TAC. \n\TAC team can contact platform team to provide distinctive identifier \n\for endpoint"

ISSU-3-FSM_RUNTIME_ERR

3-Error

Client '[chars]' with ID [dec] has '[chars]' in session [dec].

Runtime error occurs during FSM negotiation.

ha-issu-infra

"'show issu session | include <session id>' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why this runtime error occurs. Use 'show issu fsm | include <session id>'\n\to get error reason for futher debug."

ISSU-3-FSM_NEGO_SEND_ERR

3-Error

Client '[chars]' with ID [dec] encountered '[chars]' in session [dec].

Creation/removal of the named port failed for IPC.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why creation/removal of the named port failed for IPC"

ISSU-3-FSM_MISMATCH_MTU

3-Error

ISSU nego failed for client [chars][dec] entity_id [dec] session [dec] due to mismatch of mtu size [dec] & [dec].

-

-

-

ISSU-3-ERP_AGENT

3-Error

[chars]

The send message function call failed.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why one of the primary functions for the ERP agent failed"

ISSU-3-ERP_CLIENT

3-Error

For context ID [dec] [chars]

One of the primary functions for the ERP client failed.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why one of the primary functions for the ERP client failed"

ISSU-3-ERP_CLIENT_EVENT

3-Error

Unknown [chars] event - [dec]

An unknown event was received

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why an unknown event was received"

ISSU-3-DEBUG_ERROR

3-Error

[chars]

Error happens when turning on ISSU debug.

ha-issu-infra

"'show issu client | include <client id>' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead"

ISSU-3-NO_PEER_UID

3-Error

No peer uid found at [chars]

No peer uid with this value found registered in ISSU Database

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why no peer uid with this value foundi registered in ISSU Database"

ISSU-3-NO_UID

3-Error

No uid [dec] registered with ISSU at [chars]

No uid with this value found registered in ISSU Database

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why no uid with this value found registered in ISSU Database"

ISSU-3-PROTO_CLIENT_REG

3-Error

Proto Client registration for [chars] has failed

Protocol client has failed to register with ISSU

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why protocol client has failed to register with ISSU"

ISSU-3-PROTO_CLIENT_ENTITY_UNREG

3-Error

Proto Client entity unreg for [chars] has failed

Protocol client has failed to unregister its entity with ISSU

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why protocol client has failed to unregister its entity with ISSU"

ISSU-3-INCONSISTENT_MSG_TYPE

3-Error

[chars]

Foreign owned field transformation failed

ha-issu-infra

"Copy the error and send it to TAC."

ISSU-3-EXTERNAL_MATRIX_FILE_ERR

3-Error

Line [dec]: [chars]

External matrix file data is corrupted

ha-issu-infra

"An error was found in the external " "matrix data file. Open a case with TAC and attach output of " "<CmdBold>more ivfs:/<matrix_cm_file><NoCmdBold> command " "where <matrix_cm_file> is the output of <CmdBold>dir " "system:image<NoCmdBold> command."

ISSU-3-PEER_UID_CB_IS_NULL

3-Error

Peer uid control block is NULL

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-TRANSPORT_ERP_UID_CB_IS_NULL

3-Error

Transport ERP uid control block is NULL

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-PEER_IMAGE_INCOMPATIBLE

3-Error

Peer image [chars] version [chars] on peer uid [dec] is incompatible

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-PEER_IMAGE_NOT_IN_INCOMP_LIST

3-Error

Peer image [chars] version [chars] on peer uid [dec] is not in the

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-PEER_IMAGE_REM_FROM_INCOMP_LIST

3-Error

Peer image [chars] version [chars] on peer uid [dec] being removed

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-PEER_INCOMP_SET

3-Error

Peer incompatibility set for image [chars] version [chars] on peer

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-INCOMPATIBLE_PEER_UID

3-Error

Setting image [chars] version [chars] on peer uid [dec] as incompatible

Peer is incompatible

ha-issu-infra

"A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby"

ISSU-3-SESSION_RENEGOTIATE

3-Error

Client Attempting to renegotiate on session [dec]

Client Attempting to renegotiate session

ha-issu-infra

"A Client is attempting to renegotiate on session\n\without unregistering it and do the negotiation over again. This is not allowed\n\and is considered an error condition. The client should unregister the msg\n\session first and then re-register and attempt the negotiation."

ISSU-3-MSG_NEGO_RESULT_CHUNK

3-Error

Failed to [chars] element [hec]

Failed to lock or free the message negociation result chunk element

ha-issu-infra

"MSG negociation result element is locked and unlocked during avl_walk_extended of msg_nego_result_cb_root. The failure to lock or free of the element indicates invalid element or corrupted chunk memory. Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-ISSU_INIT_NOT_COMPLETE

3-Error

[chars]

ISSU initialization has not been completed

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-EMPTY_DUMMY_VERSION

3-Error

[chars] is empty under client [chars][dec] entity[dec].

dummy version is empty.

ha-issu-infra

"copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already"

ISSU-3-DUP_DUMMY_VERSION_REG

3-Error

[chars] is already registered under client [chars][dec] entity[dec] and msgtype[dec]

Item is registered already under that msg type.

ha-issu-infra

"'show issu message type | include <client id> <entity_id> <msgtype>' and copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already"

ISSU-3-FAILED_TO_ALLOC_DUMMY_VERSION

3-Error

Can not allocate [chars] under client [chars][dec] and entity[dec]

Can not allocate dummy version under client and entity.

ha-issu-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ISSU-3-DUMMY_VERSION_OUT_OF_RANGE

3-Error

Dummy msg version [dec] is out of range for msg[dec] under client [chars][dec] and entity[dec].

dummy msg version is out of range

ha-issu-infra

"'show issu message type | include <client id> <entity_id> <msg_type>' and copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already"

ISSU-3-BAD_PARAMS

3-Error

[chars]

Bad parameters are being passed

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-HANDLE_SIZE

3-Error

Handle buffer size is [dec] should be [dec]

Statically defined handle buffer size is incorrect

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-REF_TREE

3-Error

[chars] reference tree [chars] failed

The AVL based ISSU reference tree operation failed

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-CLIENT_REG_DIST

3-Error

Failed to [chars] distributed client [dec]

Distributed client reservation or unreservation failed

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-JID

3-Error

Failed to get the local process JID with err [dec]

The system manager call to collect the job-id failed

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-BASE_CLIENT_CHECK_COMPATIBILITY

3-Error

[chars]

Error found during checking of ISSU base client compatibility

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-INCOMPATIBLE_BASE_CLIENTS

3-Error

[chars]\n

List of ISSU base clients found incompatible

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-SESSION_ID_ERROR

3-Error

Failed to [chars] session id [dec] for [chars]

Session ID related operation failed

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-FOF_NEGO_RESULT_INCONSISTENT

3-Error

FOF owner msg type [dec] of owner client [chars][dec] entity [dec].

An owner FOF message of interest to an using client has inconsistent negotiation results in different owner sessions under the same entity

ha-issu-infra

"Copy the error and send it to TAC. TAC team can " "contact ISSU infrastructure team to investigate " "the problem."

ISSU-3-INTERRUPT_LEVEL_SESSION_OPERATION

3-Error

[chars] [chars] [dec] [chars] [dec]

ISSU session registeration or unregisteration should not be done at interrupt level

ha-issu-infra

"Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem."

ISSU-3-XFORM_CALLBACK

3-Error

No [chars] callback specified for client [chars][dec] msg [dec] from version [dec] to version [dec] in session [dec] .

Client didn't specify transformation function

ha-issu-infra

"Copy the error and send it to TAC. TAC team\n\ can contact ISSU client team to check why reported\n\ callback is not specified"

ISSU-3-CAP_TABLE_OUT_OF_BOUND

3-Error

Cap_table_count [dec] is out of bound max is [dec] for

The cap_table_count is out of bound for the cap_entry_id.

ha-issu-infra

"Copy the error and send it to TAC. TAC team " "can contact ISSU infrastructure team to check why the count " "is out of bound for the cap_entry_id."

IPV6_INTF-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_INTF-3-MIN_MTU

3-Error

The link MTU of [chars] is below the [dec]-byte minimum IPv6 link MTU.

As specified in the standard IPv6 requires that every link has an MTU of at least 1280. Since this link's MTU is below that IPv6 is held down on this interface.

ipv6

LOG_STD_NO_ACTION

IPV6_INTF-3-SET_MTU

3-Error

The link MTU of [chars] is below the [dec]-byte user set IPv6 link MTU.

The interface link MTU is below the user set IPv6 link MTU. IPv6 is held down on this interface.

ipv6

LOG_STD_NO_ACTION

IPV6_INTF-4-L2_MISMATCH

4-Warning

High load on interface events [chars] auto-recovery complete.

-

-

-

IPV6_INTF-3-NO_PROCESS

3-Error

Cannot start IPv6 Interface Process.

The IPv6 Interface Process could not be started. Interfaces will not be enabed for IPv6 Processing. This machine will not be able to process any IPv6 packets.

ipv6

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPV6_ADDRESS-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_ADDRESS-3-NO_UNIQUE_IDENTIFIER

3-Error

Cannot determine an unique IPv6 identifier for the system. IPv6 will not be started.

An IPv6 process could not be started. This machine will not be able to process any IPv6 packets.

ipv6

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPV6_ADDRESS-3-ADDRESS_CFG

3-Error

%P/[dec] can not be configured on [chars] [chars]

An error was encountered while configuring an IPv6 address

ipv6

LOG_STD_ACTION

IPV6_ADDRESS-3-NULLIDB

3-Error

Uninitialized interface pointer - [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_ADDRESS-3-OPINPROGRESS

3-Error

Operation in progress - [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_ADDRESS-3-RESERVED_INTFID

3-Error

Removing %P from [chars] - contains reserved interface identifier. [chars]

Removing IPv6 global address contains the reserved interface identifier

ipv6

LOG_STD_ACTION

KEYSTORE_AE46C1-6-SELF_TEST_PASS

6-Information

Keystore pass power on self test

keystore pass power on self test for both SHA1 and HMAC-SHA1

-

-

KEYSTORE_AE46C1-3-SELF_TEST_FAILURE

3-Error

Keystore power on self test failure. [chars]

keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state.

-

"Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced."

KEYSTORE_AE46C1-6-RANDOM

6-Information

A pseudo-random number was generated twice in succession[dec].

A pseudo-random number generator produced the same number twice\n\ in succession.

-

"Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative."

KEYSTORE-3-IFS_OPEN_W

3-Error

Failed to open file \[chars]\ for writing software keystore. [chars]

An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_WRITE

3-Error

An error occurred while writing to the software keystore file.

CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_OPEN_R

3-Error

Failed to open file \[chars]\ for reading software keystore. [chars]

An error occurred while opening the keystore file for reading. CTS keys could not be retrieved.

-

-

KEYSTORE-3-IFS_READ

3-Error

An error [chars] occurred while reading from the software

CTS keys could not be retrieved from persistent storage.

-

-

KEYSTORE-3-BAD_MAGIC

3-Error

Bad magic number 0x%08x in software keystore file \[chars]\.

Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-UNEXPECTED_EOF

3-Error

Unexpected end of file while reading software keystore \[chars]\.

Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-IPCPORT

3-Error

Failed to create IPC port [chars] for keystore redundancy. [chars].

An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCOPEN

3-Error

Failed to open IPC port to peer for keystore redundancy: [chars]

An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCNOCONN

3-Error

No IPC communication path to peer available for keystore [chars].

No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCSEND

3-Error

IPC send error [chars] while sending [chars].

An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-ISSU_INCOMPAT

3-Error

Standby incompatible for SSO.

The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode.

-

-

KEYSTORE-3-IPC_NO_PROC

3-Error

Could not create a process to receive keystore redundancy messages.

An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-NO_KEYSTORE

3-Error

CTS hardware keystore is not responsive and software emulation is not enabled.

The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore.

-

-

KEYSTORE-3-SESSION

3-Error

KeyStore ISSU client [chars]

KeyStore ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up.

-

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

RBM-7-RBM_ASSERT

7-Debug

Assertion Failure [chars] @[chars]:[dec] : [chars]

RBM_INTERNAL_PUBLIC_ERROR

RBM_DDTS_COMPONENT

LOG_STD_ACTION

DMB-0-DMB_EMERG

0-Emergency

[chars]

DMB_INTERNAL_ERROR

DMB_DDTS_COMPONENT

LOG_STD_ACTION

DMB-1-DMB_ALERT

1-Alert

[chars]

DMB_INTERNAL_ERROR

DMB_DDTS_COMPONENT

LOG_STD_ACTION

DMB-2-DMB_CRIT

2-Critical

[chars]

DMB_INTERNAL_ERROR

DMB_DDTS_COMPONENT

LOG_STD_ACTION

DMB-3-DMB_ERR

3-Error

[chars]

DMB_INTERNAL_ERROR

DMB_DDTS_COMPONENT

LOG_STD_ACTION

DMB-4-DMB_WARNING

4-Warning

[chars]

DMB_INTERNAL_ERROR

DMB_DDTS_COMPONENT

LOG_STD_ACTION

DMB-5-DMB_NOTICE

5-Notice

[chars]

Normal but significant conditions

DMB_DDTS_COMPONENT

LOG_STD_ACTION

DMB-6-DMB_INFO

6-Information

[chars]

Informational messages

DMB_DDTS_COMPONENT

LOG_STD_NO_ACTION

DMB-7-DMB_ASSERT

7-Debug

Assertion Failure [chars] @[chars]:[dec] : [chars]

DMB_INTERNAL_ERROR

DMB_DDTS_COMPONENT

LOG_STD_ACTION

RBM-0-RBM_EMERG

0-Emergency

[chars]

RBM_INTERNAL_ERROR

RBM_DDTS_COMPONENT

LOG_STD_ACTION

RBM-1-RBM_ALERT

1-Alert

[chars]

RBM_INTERNAL_ERROR

RBM_DDTS_COMPONENT

LOG_STD_ACTION

RBM-2-RBM_CRIT

2-Critical

[chars]

RBM_INTERNAL_ERROR

RBM_DDTS_COMPONENT

LOG_STD_ACTION

RBM-3-RBM_ERR

3-Error

[chars]

RBM_INTERNAL_ERROR

RBM_DDTS_COMPONENT

LOG_STD_ACTION

RBM-4-RBM_WARNING

4-Warning

[chars]

RBM_INTERNAL_ERROR

RBM_DDTS_COMPONENT

LOG_STD_ACTION

RBM-5-RBM_NOTICE

5-Notice

[chars]

Normal but significant conditions

RBM_DDTS_COMPONENT

LOG_STD_ACTION

RBM-6-RBM_INFO

6-Information

[chars]

Informational messages

RBM_DDTS_COMPONENT

LOG_STD_NO_ACTION

RBM-3-RBM_PARSE_RBACL

3-Error

Could not parse command for creating [chars] Role-Based Access List '[chars]'\n\t'[chars]'

An error occured while attempting to create Role-Based Access List

RBM_DDTS_COMPONENT

"This error could occur when TrustSec attempts to install RBACL it has acquired from ACS" " while configuration mode is locked exclusively. TrustSec will retry this operation and" " should eventually succeed once configuration mode is no longer locked. If the error occurs" " when the configuration mode is not locked or if the RBACL does not get installed after" " the configuration mode lock is released "LOG_STD_ACTION

RBM-3-RBM_PARSE_ACE

3-Error

Could not parse command for adding ACE '[chars]' to [chars] Role-Based Access List '[chars]'

An error occured while attempting to add an ACE to a Role-Based Access List. The ACE syntax is most likely incompatible with the type of RBACL.

RBM_DDTS_COMPONENT

"Verify the syntax of the ACEs of the RBACL in ACS and the IP protocol versions the RBACL" " applies to." " RBACL ACE syntax could be verified by manually configuring IP/IPv6 RBACL on the system" " within config-rb-acl/config-ipv6rb-acl configuration mode respectively."

RBM-3-RBM_PARSE_CMD

3-Error

Could not parse command. See command output and errors below \n[chars]

An error occured while attempting to parse command. Look for command output and parser errors below this message.

RBM_DDTS_COMPONENT

"Follow the recommended action of the additional error messages that follow this message".

RBM-6-SGACLHIT

6-Information

ingress_interface='[chars]' sgacl_name='[chars]' action='[chars]' protocol='[chars]' src-vrf='[chars]' src-ip='[inet]' src-port='[dec]' dest-vrf='[chars]' dest-ip='[inet]' dest-port='[dec]' sgt='[dec]' dgt='[dec]' logging_interval_hits='% PRIu64 '

A packet matching the log criteria for the given sg access list was \ detected.

-

LOG_STD_NO_ACTION

RBM-6-SGACLHIT_V6

6-Information

ingress_interface='[chars]' sgacl_name='[chars]' action='[chars]' protocol='[chars]' src-vrf='[chars]' src-ip='%P' src-port='[dec]' dest-vrf='[chars]' dest-ip='%P' dest-port='[dec]' sgt='[dec]' dgt='[dec]' logging_interval_hits='% PRIu64 '

A IPv6 packet matching the log criteria for the given sg access list \ was detected.

-

LOG_STD_NO_ACTION

CTS-3-INIT

3-Error

CTS HA ISSU client initialization failed to [chars]. Error: [dec] [chars]

CTS HA ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-SESSION_REGISTRY

3-Error

CTS HA ISSU client failed to register session information. Error: [dec] [chars]

The CTS HA ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

CTS_DDTS_COMPONENT

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

CTS-3-SESSION_UNREGISTRY

3-Error

CTS HA ISSU client failed to unregister session information. Error: [dec] [chars]

The CTS HA ISSU client failed to unregister session information.

CTS_DDTS_COMPONENT

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

CTS-3-SEND_NEGO_FAILED

3-Error

CTS HA ISSU client failed to send negotiation message. Error: [dec] [chars]

The CTS HA ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

CTS_DDTS_COMPONENT

"show logging and show checkpoint client"

CTS-3-GET_BUFFER

3-Error

CTS HA ISSU client failed to get buffer for message. Error: [dec] [chars]

The CTS HA ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

CTS_DDTS_COMPONENT

"show logging and show checkpoint client"

CTS-6-INCOMPAT

6-Information

CTS HA ISSU client negotiation results incompatible

The CTS HA ISSU client message version is not compatible on Active and Standby. No CTS data will be synced to Standby in this case

CTS_DDTS_COMPONENT

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

CTS-3-CAP_NOT_COMPATIBLE

3-Error

CTS HA capability not compatible

CTS HA failed during capability negotiation.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-CAP_INVALID_SIZE

3-Error

CTS HA empty tlv size.

Received empty tlv list during capability negotiation.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-MSG_NOT_COMPATIBLE_WITH_PEER

3-Error

Message [dec] in component [dec] is not compatible with the peer.

Message not compatible with the peer.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-CTS_POLICY_SERVER_CREDENTIALS

3-Error

Valid Policy-server credentials have not configured on device

CTS policy-server username is not configured

-

LOG_STD_ACTION

CTS-3-CTS_POLICY_SERVER_INVALID_CREDENTIALS

3-Error

Invalid Policy-server credentials have configured on device OR Server port number is incorrect

CTS policy-server username or password are invalid

-

LOG_STD_ACTION

CTS-3-CTS_POLICY_SERVER_ENCRYPT_REVERSIBLE

3-Error

Password conversion failed

CTS policy-server password conversion failed

-

LOG_STD_ACTION

CTS-3-CTS_POLICY_SERVER_ENCRYPT_TEMP

3-Error

Password conversion failed

CTS policy-server password conversion failed

-

LOG_STD_ACTION

CTS-3-CTS_POLICY_SERVER_SG_TBL_ALLOC

3-Error

Server group table memory allocation failed

CTS HTTP based download will impact

-

LOG_STD_ACTION

CTS-0-IFC_OUT_OF_MEM

0-Emergency

[chars] failed to create [chars] due to insufficient memory

The system is experiencing insufficent memory.

-

LOG_STD_ACTION

CTS-3-IFC_NO_IDB_IN_SWACT

3-Error

Failed to locate IDB in link object

Failed to locate IDB in link object

-

LOG_STD_ACTION

CTS-3-IFC_DATA_NULL

3-Error

[chars] encounters NULL [chars]

An unexpected NULL pointer/data is encountered.

-

LOG_STD_ACTION

CTS-3-IFC_LINK_OBJ_FAILED

3-Error

[chars] failed to get link_obj for int[chars]

An error occured while CTS IFC attempts to access the link object.

-

LOG_STD_ACTION

CTS-5-IFC_DATA_DESC_DECODE_FAILED

5-Notice

[chars] failed to decode the data-descriptor - swidb unknown

An error occured while the system attempted to decode the data-descriptor in order to obtain the swidb

-

LOG_STD_ACTION

CTS-3-IFC_DATA_DESC_ENCODE_FAILED

3-Error

[chars] failed to encode the data-descriptor for int[chars]

An error occured while the system attempted to encode the swidb into the data-descriptor

-

LOG_STD_ACTION

CTS-3-IFC_SYNC_FAILED_2

3-Error

[chars] Failed to send [chars] sync msg[chars] to Standby

An error occcured while CTS IFC is performing a sync to the Standby.

-

LOG_STD_ACTION

CTS-3-IFC_SYNC_FAILED

3-Error

Failed to send [chars] sync msg[chars] to Standby

An error occcured while CTS IFC is performing a sync to the Standby.

-

LOG_STD_ACTION

CTS-6-IFC_CACHE_APPLIED

6-Information

Cache data applied for int[chars]

Inform the user that the CTS link is brought up using cache data

-

LOG_STD_ACTION

CTS-6-IFC_INIT_STATE

6-Information

Interface Controller in INITIALIZATION state for int[chars]

IFC Entering INIT State

-

LOG_STD_NO_ACTION

CTS-3-INVALID_CTS_OPER_MODE

3-Error

Invalid CTS Mode. Supported modes are Manual and Auto

Invalid CTS Mode. Supported modes are manual and auto

-

LOG_STD_ACTION

CTS-6-IFC_AUTHC_STATE

6-Information

Interface Controller in AUTHENTICATION state for int[chars]

IFC Entering Authentication State

-

LOG_STD_NO_ACTION

CTS-3-IFC_FAILED_AUTHC_SUCCESS_NOTIFY

3-Error

Failed to send authentication success to the core for int[chars]

-

-

-

CTS-6-IFC_AUTHORIZE_STATE

6-Information

Interface Controller in AUTHORIZATION state [chars] for int[chars] peer[chars]

IFC Entering Authorization State

-

LOG_STD_NO_ACTION

CTS-3-IFC_NO_IDB_IN_AUTHORIZE_STATE

3-Error

Authorization State: IDB could not be retrieved: state[chars] peer[chars]

-

-

-

CTS-3-IFC_FAIL_PRGM_PSGT

3-Error

Could not program hardware for propagate SGT Port SGT[dec]

IFC could not program hardware for propagate SGT

-

LOG_STD_ACTION

CTS-3-IFC_FAILED_AUTHZ_FAIL_NOTIFY

3-Error

Failed to send authorization failure to the core for int[chars]

-

-

-

CTS-3-IFC_FAILED_AUTHZ_SUCCESS_NOTIFY

3-Error

Failed to send authorization success to the core for int[chars]

-

-

-

CTS-3-IFC_FAILED_ENV_DATA_DNLD

3-Error

Failed to download environment data for int[chars]

-

-

-

CTS-6-IFC_SAP_STATE

6-Information

Interface Controller in SAP NEGOTIATION state for int[chars]

IFC Entering SAP State

-

LOG_STD_NO_ACTION

CTS-3-IFC_NO_IDB_IN_SAP_STATE

3-Error

SAP State: IDB could not be retrieved

IFC SAP State: IDB could not be retrieved

-

LOG_STD_ACTION

CTS-3-IFC_FAILED_SAP_SUCCESS_NOTIFY

3-Error

Failed to send SAP success to the core for int[chars]

-

-

-

CTS-3-IFC_FAILED_SAP_FAIL_NOTIFY

3-Error

Failed to send SAP failure to the core for int[chars]

-

-

-

CTS-6-IFC_OPEN_STATE

6-Information

Interface Controller in OPEN state for int[chars]

IFC Entering OPEN State

-

LOG_STD_NO_ACTION

CTS-3-IFC_ADD_SUPPLICANT_FAIL

3-Error

Failed to add supplicant cannot open port[chars]

-

-

-

CTS-6-IFC_DISCONNECT_STATE

6-Information

Interface Controller in DISCONNECT state for int[chars]

IFC Entering DISCONNECT State

-

LOG_STD_NO_ACTION

CTS-3-IFC_FAILED_DISCONNECT_NOTIFY

3-Error

Failed to send disconnect notify to the core for int[chars]

-

-

-

CTS-6-IFC_HELD_STATE

6-Information

Interface Controller in HELD state for int[chars]

IFC Entering HELD State

-

LOG_STD_NO_ACTION

CTS-6-IFC_LICENSE_ERR_STATE

6-Information

Interface Controller in LICENSE ERR state for int[chars]

IFC Entering LICENSE ERR State

-

LOG_STD_NO_ACTION

CTS-3-IFC_SM_INIT_FAIL

3-Error

SM INIT failed

IFC SM INIT failed

-

LOG_STD_ACTION

CTS-6-IFC_SM_STATE

6-Information

Interface Controller state machine started for int[chars]

IFC Started

-

LOG_STD_NO_ACTION

CTS-3-IFC_LOST_TIMER_CXT

3-Error

Lost Timer context

IFC Lost Timer context

-

LOG_STD_ACTION

CTS-3-IFC_LOST_AUTHC_REAUTH_TIMER_CXT

3-Error

Lost AUTHC reauth timer context

IFC Lost AUTHC reauth timer context

-

LOG_STD_ACTION

CTS-3-IFC_LOST_SOCK_CLEANUP_TIMER_CXT

3-Error

Lost socket cleanup timer context

IFC Lost socket cleanup timer context

-

LOG_STD_ACTION

CTS-3-IFC_LOST_DOT1X_PAE_TIMER_CXT

3-Error

Lost DOT1x PAE timer context

IFC Lost DOT1x PAE timer context

-

LOG_STD_ACTION

CTS-6-IFC_RX_AUTHC_SUCCESS

6-Information

Received AUTHC SUCCESS for peer[chars] role[chars] sgt[chars] int[chars]

-

-

-

CTS-4-IFC_RX_AUTHC_REJECT

4-Warning

Received AUTHC REJECT for peer[chars] role[chars] int[chars]

-

-

-

CTS-4-IFC_RX_AUTHC_FAIL

4-Warning

Received AUTHC FAIL for role[chars] int[chars]

IFC Received AUTHC FAIL

-

LOG_STD_ACTION

CTS-3-IFC_RX_AUTHC_SUCCESS_FAIL

3-Error

Received AUTHC Success for peer[chars] role[chars] int[chars]

IFC Received AUTHC success but failed to process due to error

-

LOG_STD_ACTION

CTS-4-IFC_RX_AUTHC_LOGOFF

4-Warning

Received AUTHC LOGOFF for peer[chars] role[chars] int[chars] state[chars]

-

-

-

CTS-4-IFC_RX_AUTHC_NO_RESP

4-Warning

Received AUTHC NO RESP for int[chars]

IFC Received AUTHC NO RESP

-

LOG_STD_ACTION

CTS-3-IFC_CACHE_RESTORE_FAIL

3-Error

Cache Restoration Failed

IFC Cache restoration failed owing to errors in NVRAM file open operation. Even though CTS cache is enabled link bring up cannot bypass IFC state machine

-

LOG_STD_ACTION

CTS-3-IFC_CACHE_UPDATE_FAIL

3-Error

Cache Update Failed

IFC Cache update failed owing to errors in NVRAM file write operation.

-

LOG_STD_ACTION

CTS-3-IFC_CACHE_BAD_LEN

3-Error

Cache File [chars] bad length [dec] expecting [dec]

IFC Cache file bad length may be corrupted.

-

LOG_STD_ACTION

CTS-3-CORE_PROCESS_CREATION_FAILURE

3-Error

Failed to create CTS_CORE process

CTS_CORE: Failed to create CTS_CORE process

-

LOG_STD_ACTION

CTS-3-CORE_PROCESS_TERMINATED

3-Error

Process getting killed since queue is not created

CTS_CORE: Process getting killed since queue is not created

-

LOG_STD_ACTION

CTS-3-DOT1X_UNCONFIGURE_FAILURE

3-Error

Failed to unconfigure dot1x on int[chars]

CTS_CORE: Failed to unconfigure dot1x

-

LOG_STD_ACTION

CTS-3-INVALID_MSGID_RCV

3-Error

[chars] received invalid HA/ISSU msgId[dec]

CTS Core encountered an unexpected invalid HA/ISSU message ID.

-

LOG_STD_ACTION

CTS-3-GENERIC_FAILURE

3-Error

[chars] [chars]

CTS Core encountered internal error.

-

LOG_STD_ACTION

CTS-5-DOT1X_INIT_FAILED

5-Notice

Failed to initialize dot1x for int[chars]

An error occcured while CTS attempts to initialize dot1x for a CTS link

-

LOG_STD_ACTION

CTS-5-DOT1X_CONFIG_FAILED

5-Notice

Failed to configure dot1x for int[chars]

An error occcured while CTS attempts to configure dot1x for a CTS link

-

LOG_STD_ACTION

CTS-5-DOT1X_PAE_FAILED

5-Notice

Failed to [chars] dot1x PAE[chars] for int[chars]

An error occcured while CTS attempts to start/stop dot1x PAEs for

-

LOG_STD_ACTION

CTS-6-DOT1X_PAE_CONFIG

6-Information

[chars] dot1x PAE[chars] for int[chars]

The interface has been configured for dot1x PAEs

-

LOG_STD_ACTION

CTS-3-DOT1X_FORCE_PORT_AUTHORIZED_FAILED

3-Error

Failed to force dot1x port authorized for int[chars]

An error occcured while CTS attempts to force dot1x port authorized on a CTS link

-

LOG_STD_ACTION

CTS-6-DOT1X_FORCE_PORT_AUTHORIZED_SUCCESS

6-Information

Successfully forced dot1x port authorized for int[chars]

Port has been put to FORCE AUTHORIZED on a CTS link

-

LOG_STD_ACTION

CTS-6-PORT_AUTHORIZED_SUCCESS

6-Information

Port authorized for int[chars]

Port has been authorized on a CTS link

-

LOG_STD_ACTION

CTS-3-PORT_AUTHORIZED_FAILED

3-Error

Failed to authorize Port for int[chars]

Port failed to be authorized on a CTS link

-

LOG_STD_ACTION

CTS-6-PORT_UNAUTHORIZED

6-Information

Port unauthorized for int[chars]

Port has been unauthorized on a CTS link

-

LOG_STD_ACTION

CTS-3-GLOBAL_DOT1X_DISABLED

3-Error

Global dot1x config is currently disabled - CTS will not run

Global dot1x is not enabled and hence CTS will not run

-

LOG_STD_ACTION

CTS-3-GCM_NO_LICENSE

3-Error

CTS link [chars] is being shut down: please install MACSec Encryption License http:/www.cisco.com/go/license

A MACSec Encryption License is required to use gcm-encryption on secure links. All CTS links configured to run gcm-encryption will be held in administratively down state until the gcm-encrytion is removed from the interface configuration or until a MACSec Encryption License is installed.

-

"Either install a MACSec Encryption License or configure all CTS " "interfaces with cipher modelists that do not include gcm."

CTS-3-STDBY_NO_LICENSE

3-Error

CTS link [chars] may be shut down on switchover: please install MACSec Encryption License on the standby supervisor http:/www.cisco.com/go/license

A MACSec Encryption License is required to use gcm-encryption on secure links. If the active supervisor has a license but the standby does not then links may run GCM encryption. However on switchover all links running GCM will be shut down because the new active does not have a License.

-

"Either install a MACSec Encryption License or configure all CTS " "interfaces with cipher modelists that do not include gcm."

CTS-3-SSO_NO_LICENSE

3-Error

CTS GCM links are being shut down. Please install a MACSec Encryption License on the new active supervisor http:/www.cisco.com/go/license

A MACSec Encryption License is required to use gcm-encryption on secure links. If the active supervisor has a license but the standby does not then links may run GCM encryption. However on switchover all links running GCM will be shut down because the new active does not have a License.

-

LOG_STD_DDTS_TAC_DETAILS

CTS-3-SEND_MSG_TO_CORE_FAILED

3-Error

Failed to send msg[dec] to core process

An error occcured while CTS attempts to send a message event to the core process

-

LOG_STD_ACTION

CTS-3-MODE_LIST_CKSUM_ERROR

3-Error

CTS SAP mode-list checksum failure on interface [chars].\n

CTS SAP mode-list checksum failure has been detected on this interafce which could provide crypto services. This event may be caused by memory corruption occuring in the interface configutration or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event the system has been forced to reload.

-

LOG_STD_ACTION

CTS-3-CTS_DISALLOW_L3_CONFIG

3-Error

[chars].\nRemoving CTS Layer3 TrustSec Forwarding configuration from interface[chars]

Platform ASIC does not support CTS Layer2 and CTS layer3 TrustSec Forwarding configurations to co-exist on the same ASIC instance

-

LOG_STD_ACTION

CTS-3-CTS_DISALLOW_L2_CONFIG

3-Error

[chars].\nRemoving CTS Layer2 configuration from interface[chars]

-

-

-

CTS-6-ENV_DATA_COA_REQUEST

6-Information

Command [chars]=[chars]-[chars]

A Change of Authorization request command is received for update-env-data

-

LOG_STD_ACTION

CTS-6-REAUTHENTICATION_PERIOD_CHANGED

6-Information

Reauthentication period is changed to [dec]

Reauthentication period is changed while applying configuration change to the link object

-

LOG_STD_NO_ACTION

CTS-6-DOT1X_PEER_NO_RESP

6-Information

DOT1X reported peer NO RESPONSE message on int[chars]

DOT1X reported peer NO RESPONSE message

-

LOG_STD_NO_ACTION

CTS-6-DOT1X_PEER_LOGOFF

6-Information

DOT1X reported peer LOGOFF message on int[chars]

DOT1X reported peer LOGOFF message

-

LOG_STD_NO_ACTION

CTS-6-CRTCL_AUTH_ENABLE

6-Information

Critical-Authentication enabled on interface[chars]

CTS critical-autentication is enabled on given interface

-

LOG_STD_NO_ACTION

CTS-6-CRTCL_AUTH_DISABLE

6-Information

Critical-Authentication disabled on interface[chars]

CTS critical-authentication is disabled on given interface

-

LOG_STD_NO_ACTION

CTS-6-CRTCL_AUTH_REAUTH

6-Information

Critical-Authentication starts re-authentication on interface[chars]

CTS critical-authentication re-authenticates peer on given interface

-

LOG_STD_NO_ACTION

CTS-0-AUTHZ_OUT_OF_MEM

0-Emergency

[chars] failed to create [chars] due to insufficient memory

The system is experiencing insufficent memory.

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_CREATE_FAILED

3-Error

[chars] failed to create [chars]

An error occurred while CTS Authz attempts to create an internal data structure.

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_EXCEEDS_LIMIT

3-Error

[chars] encountered [chars][dec] exceeds max[dec]

Data exceeds maximum limits allowed.

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_UNINIT

3-Error

[chars] appears uninitialized

CTS Authz unexpectedly encountered an unitialized data

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_NULL

3-Error

[chars] encounters NULL [chars]

An unexpected NULL pointer/data is encountered.

-

LOG_STD_ACTION

CTS-3-AUTHZ_SYNC_FAILED

3-Error

Failed to send [chars] sync msg[chars] to Standby

An error occcured while CTS Authz is performing a sync to the Standby.

-

LOG_STD_ACTION

CTS-3-AUTHZ_FAILED_SYNC_RCV

3-Error

Standby failed receive sync msg[chars]

An error occcured while the Standby is receiving sync data from the Active.

-

LOG_STD_ACTION

CTS-3-AUTHZ_NOT_SUPPORTED

3-Error

[chars] encountered [chars] not unsupported

CTS encountered an unsupported data type or feature. This could be due to incompatibility

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_FAILED

3-Error

[chars] failed to obtain [chars]

An error occurred while CTS Authz attempted to get/create a data structure

-

LOG_STD_ACTION

CTS-3-AUTHZ_INVALID_DATA

3-Error

[chars] encountered invalid [chars]

CTS Authz encountered an unexpected invalid data type.

-

LOG_STD_ACTION

CTS-3-AUTHZ_ADD_DATA_FAILED

3-Error

[chars] failed to add [chars] to [chars]

An error occurred while CTS Authz attempted to build its database.

-

LOG_STD_ACTION

CTS-3-AUTHZ_GENERIC_FAILURE

3-Error

[chars] [chars]

CTS Authz encountered internal error.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_WILDCARD_FAILED

3-Error

Failed to download default/unknown policy

An error occurred while CTS attempted to acquire wildcard policy from the ACS.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_PEER_DOWNLOAD_FAILED

3-Error

Failed to download peer policy for [chars]

An error occurred while CTS attempted to acquire peer policy from the policy server

-

LOG_STD_ACTION

CTS-3-AUTHZ_SGT_POLICY_DEL_FAILED

3-Error

Failed to delete sgt policy for sgt [chars].

An error occurred while CTS attempted to delete sgt policy with invalid handle.

-

LOG_STD_ACTION

CTS-3-AUTHZ_SGT_POLICY_STALE

3-Error

sgt policy for sgt '[chars]' is not valid.

An error occurred while CTS attempted to access sgt policy with invalid handle.

-

LOG_STD_ACTION

CTS-3-AUTHZ_ACL_INFO_STALE

3-Error

ACL information is not valid.

An error occurred while CTS attempted to access ACL information with invalid handle.

-

LOG_STD_ACTION

CTS-3-AUTHZ_ACL_LIST_STALE

3-Error

ACL named list having ACE information is not valid.

An error occurred while CTS attempted to access ACL list with invalid handle.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_ACL_DEL_FAILED

3-Error

Failed to delete ACL information. Invalid ACL [chars].

An error occurred while CTS attempted to delete ACL info with invalid handle.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_SGACL_FAILED

3-Error

Failed to [chars][chars] SGACL [chars] for SGT=[chars]

An error occurred while CTS attempted to acquire SGACL policy from the policy server.

-

LOG_STD_ACTION

CTS-2-AUTHZ_POLICY_SGACL_ACE_FAILED

2-Critical

Failed to [chars][chars] SGACL '[chars]' for SGT=[chars] due to ACE '[chars]' error. Download will be retried in 60 seconds

An error occurred in the ACE while CTS attempted to acquire SGACL policy from the policy server. Retry will be attempted in 60 seconds

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_INGRESS_FAILED

3-Error

Failed to [chars] Ingress policy for [chars]

An error occurred while CTS attempted to acquire or install an Ingress policy from the ACS.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_INTERNAL_FAILED

3-Error

Failed to acquire/install policy for [chars] due to internal error

An error occurred while CTS attempted to acquire/install a policy which may be caused by internal software error

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_FAIL_TO_REMOVE

3-Error

Failed to remove [chars] policy from the authorization dbase

An error occured while CTS attempted to remove the specified policy from its database. This could result in an action not being accomplished.

-

LOG_STD_ACTION

CTS-3-POLICY_COA_SGT_FAILED

3-Error

Failed to complete CoA request for update-sgt[chars]

An error occurred while CTS attempted to service a Change of Authorization request for the update-sgt command

-

LOG_STD_ACTION

CTS-3-POLICY_COA_RBACL_FAILED

3-Error

Failed to complete request for update-rbacl[chars]-[chars]

An error occurred while CTS attempted to service a Change of Authorization request for the update-rbacl command

-

LOG_STD_ACTION

CTS-6-POLICY_COA_SGT_REQUEST

6-Information

Command [chars]=[chars]

A Change of Authorization request command is received for update-sgt

-

LOG_STD_ACTION

CTS-6-POLICY_COA_RBACL_REQUEST

6-Information

Command [chars]=[chars]-[chars]

A Change of Authorization request command is received for update-rbacl

-

LOG_STD_ACTION

CTS-6-POLICY_COA_DONE

6-Information

Command [chars]=[chars] completed

A Change of Authorization request has been serviced

-

LOG_STD_ACTION

CTS-6-POLICY_COA_NO_ACTION

6-Information

Command [chars]=[chars] has no change

A Change of Authorization request has been received but no action was taken due to the system is already in possession of the requested data

-

LOG_STD_ACTION

CTS-6-POLICY_COA_NO_SESSION

6-Information

Command [chars]=[chars] has no session associated

A Change of Authorization request has been received for infomration that the system is not in possession of

-

LOG_STD_ACTION

CTS-6-POLICY_RBACL_MONITOR_ALL

6-Information

Failed to set monitor all for dynamic policies

An error occurred while CTS attempted to set monitor flag for all dynamic installed policies.

-

LOG_STD_ACTION

CTS-3-POLICY_HA_PROC_FAIL

3-Error

Error starting up HA switchover Policy refresh process.

A failure has occurred in switchover which has prevented the policy refresh process to be lauched. User should manually refresh policies via the \cts refresh policy\ commad

-

"Issue command \"cts refresh policy\" and verify policy timers" " are active If timers do not start "LOG_STD_ACTION

CTS-6-REAUTH_TIMER_EXPIRED

6-Information

Timer expired on int[chars]

REAUTH Timer expired

-

LOG_STD_NO_ACTION

CTS-6-AUTHZ_REFRESH_EXPIRY

6-Information

Policy refresh timer[dec] secs has expired for peer[chars]

-

-

-

CTS-3-AUTHZ_CACHE_OPEN_FAIL

3-Error

[chars] failed to open cache file[chars] for read

CTS Cache read: Failed to open cache file for read

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_READ_FAIL

3-Error

[chars] failed to read from cache file[chars]

CTS Cache: Failed to read from cache file

-

LOG_STD_ACTION

CTS-6-AUTHZ_CACHE_READ_RESULT

6-Information

[chars] cache read from file[chars] [chars]

CTS Cache read from cache file done

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHED_DATA_READ_FAIL

3-Error

[chars] failed to read cached data

CTS Cache: Failed to read cached data

-

LOG_STD_ACTION

CTS-6-AUTHZ_CACHED_DATA_EXPIRED

6-Information

[chars] cached data expired

CTS Cache: Cached data expired

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_OPEN_WRITE_FAIL

3-Error

[chars] failed to open cache file[chars] for write

CTS Cache: Failed to open cache file for write

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_SRV_WRITE_FAIL

3-Error

[chars] failed to write server list to cache file[chars]

CTS Cache: Failed to write server list to cache file

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_MSGT_WRITE_FAIL

3-Error

[chars] failed to write Multicast SGT Table to cache file[chars]

CTS Cache: Failed to write Multicast SGT Table to cache file

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_SGT_WRITE_FAIL

3-Error

[chars] failed to write SGT SG Name Table to cache file[chars]

CTS Cache: Failed to write SGT SG Name Table to cache file

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_PEER_POL_WRITE_FAIL

3-Error

Failed to write peer policy to cache

CTS Authz Cache: Failed to write peer policy to cache

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_SGT_POL_WRITE_FAIL

3-Error

Failed to write SGT policy to cache

CTS Authz Cache: Failed to write SGT policy to cache

-

LOG_STD_ACTION

CTS-3-AAA_NO_CONTEXT

3-Error

Failed to retrieve AAA context to construct AAA attribute for RADIUS request

CTS AAA Request Add : Failed to retrieve AAA context to construct AAA attribute for RADIUS request

-

LOG_STD_ACTION

CTS-3-AAA_NO_RADIUS_SERVER

3-Error

No RADIUS servers available for CTS AAA request for [chars]

CTS AAA Request Setup : No RADIUS servers available for CTS AAA

-

LOG_STD_ACTION

CTS-3-AUTHZ_SM_FAILED

3-Error

Failed to start the authorization entry state machine to start policy acquisition for peer[chars]

-

-

-

CTS-3-AUTHZ_TREE_MAP_INSERT_FAILED

3-Error

Failed to insert the authz entry info into tree map for peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_UPDATED

6-Information

Policy update received for old SGT [chars] new SGT[chars]

-

-

-

CTS-6-AUTHZ_ENTRY_ACCESS_POLICY_STATE

6-Information

Policy Acquisition in ACCESS state for peer[chars] sgt[chars]

-

-

-

CTS-6-AUTHZ_ENTRY_COMPLETE_STATE

6-Information

Policy Acquisition in COMPLETE state for peer[chars] sgt[chars]

-

-

-

CTS-5-POLICY_ACQUISITION_SUCCESS

5-Notice

Policy Acquisition success for peer[chars] sgt[chars]

-

-

-

CTS-7-AUTHZ_ENTRY_HDL_SENDL_FAILED

7-Debug

Error retrieving the authorization entry handle

Error retrieving the authorization entry handle

-

LOG_STD_ACTION

CTS-7-AUTHZ_ENTRY_PENDING_REQUEST

7-Debug

RADIUS request to acquire policy for peer[chars] sgt[chars] was not

RADIUS request to acquire policy for peer was not sent due to pending request in progress

-

LOG_STD_ACTION

CTS-7-AUTHZ_ENTRY_WAIT_FOR_ACE

7-Debug

Policy Acquisition for peer[chars] sgt[chars] is waiting for the

Policy acquisition for peer is waiting for the ACE download complete

-

LOG_STD_ACTION

CTS-3-AUTHZ_ENTRY_RADIUS_FAILED

3-Error

Policy Acquisition failed to transmit RADIUS request for peer[chars] sgt[chars]

-

-

-

CTS-7-AUTHZ_PEER_POL_DEL

7-Debug

Deleting peer policy for peer[chars] sgt[chars]

-

-

-

CTS-7-AUTHZ_PEER_POL_DEL_PENDING

7-Debug

Pending peer policy delete for peer[chars] sgt[chars] due to

Pending peer policy delete for peer due to outstanding SGACL install/uninstall

-

LOG_STD_ACTION

CTS-3-AUTHZ_UNINST_SESSION_FR_NAMELIST_FAILED

3-Error

Failed to locate named list to uninstall session

Failed to locate named list to uninstall session

-

LOG_STD_ACTION

CTS-3-AUTHZ_SESSION_UNINST_SGACL_FAILED

3-Error

Failed to detach session handle from SGACL list for sgt[chars]

-

-

-

CTS-3-AUTHZ_SESSION_SM_START_FAILED

3-Error

Failed to initialize the environment-data module

Failed to initialize the environment-data module

-

LOG_STD_ACTION

CTS-3-ENV_DATA_INIT_FAILED

3-Error

Failed to initialize and start the authorization state machine

Failed to initialize and start the authorization state machine

-

LOG_STD_ACTION

CTS-6-AUTHZ_POLICY_SGACL_ATTACH_SUCCESS

6-Information

Successfully attached RBM SGACL to RBM policy for sgt[chars]:[chars]

-

-

-

CTS-6-AUTHZ_POLICY_SGACL_SUCCESS

6-Information

Successfully [chars] SGACL for sgt[chars]

-

-

-

CTS-6-AUTHZ_POLICY_SGACL_UPDATE

6-Information

SGACL[chars]gen-id[chars] updated to SGACL[chars]gen-id[chars]

-

-

-

CTS-6-AUTHZ_POLICY_SGACL_NO_CHANGE

6-Information

Policy refresh for sgt[chars] indicates no change

-

-

-

CTS-6-AUTHZ_WAIT_POLICY_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_INSTALL_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_WAIT_FOR_RBM_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_INSTALL_SUCCESS

6-Information

Policy Installation success for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_NO_OP

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_UNINSTALL_SUCCESS_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_RETRY_INSTALL

6-Information

Policy Installation retry install for int[chars] peer[chars] flag[hec]

-

-

-

CTS-6-AUTHZ_SM_INIT

6-Information

Policy Installation state machine initializing in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_DESTROY

6-Information

Policy Installation state machine destroyed in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_STOP

6-Information

Policy Installation state machine stopped for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_RUN

6-Information

Policy Installation state machine running for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_REINIT

6-Information

Policy Installation state machine reinitialization for int[chars] peer[chars]

-

-

-

CTS-6-ENV_DATA_REFRESH_TIMER

6-Information

Time to refresh environment data

ENV data refresh timer

-

LOG_STD_NO_ACTION

CTS-3-ENV_DATA_ERROR

3-Error

Environment data error in [chars] state

ENV data error

-

LOG_STD_NO_ACTION

CTS-4-SLIST_HANDLER_FAILED

4-Warning

[chars]:tag[chars] - failed to locate server list handle.

-

-

-

CTS-4-SLIST_ADD_TO_PREFERRED_LIST_FAILED

4-Warning

[chars]:tag[chars] - failed to add server[inet]:[dec] to preferred list.

-

-

-

CTS-4-SLIST_ADD_TO_NAMED_LIST_FAILED

4-Warning

[chars]:tag[chars] - failed to add server[inet]:[dec] to named list.

-

-

-

CTS-4-SLIST_INVALID_LIST_TYPE

4-Warning

[chars]:tag[chars] - invalid server list type[dec].

-

-

-

CTS-4-CREATE_SLIST_FAILED

4-Warning

[chars]: Failed to create server list.

CTS HA failed to create server list while processing server named list sync message.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-6-ENV_DATA_START_STATE

6-Information

Environment Data Download in start state

Environment data download in start state

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-ENV_DATA_WAIT_RESP_STATE

6-Information

Environment Data Download in wait response state

Environment data download in wait response state

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-ENV_DATA_ASSESS_STATE

6-Information

Environment Data Download in assess state

Environment data download in assess state

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-ENV_DATA_ACQUISITION_SUCCESS

5-Notice

Environment data download success

Environment data download completed

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-ENV_DATA_INSTALL_SUCCESS

5-Notice

Environment data installation success

Environment data installation completed

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-ENV_DATA_CLEAR_SUCCESS

6-Information

Environment data successfully cleared.

Environment data successfully cleared.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-3-AUTHZ_ENTRY_HTTP_FAILED

3-Error

Policy Acquisition failed to transmit HTTP request for peer[chars] sgt[chars]

Policy acquisition failed to transmit HTTP request

-

LOG_STD_ACTION

CTS-3-ROOT_CA_STORE_FAIL

3-Error

Could not install the CTS trusted-root certificate.

An error occcured while installing the CTS trusted-root certificate. This means that CTS cannot validate AAA servers' certifcates received during EAP-FAST exchanges.

-

-

CTS-5-ROOT_CA_STORE_DONE

5-Notice

A trusted-root certificate to be used for CTS has been installed.

A CTS trusted-root certificate was received from a AAA server during an EAP-FAST enrollment. This certificate will be used for validating all AAA servers' certificates received from here on.

-

-

CTS-3-LSC_STORE_FAIL

3-Error

Failed to install newly-provisioned locally-significant certificate.

An error occurred while installing our locally significant certificate to be used for CTS. This means that we cannot be authenticated using a certificate. If a CTS password is available we will continue to authenticate using the password.

-

-

CTS-3-LSC_CA_STORE_FAIL

3-Error

Failed to install certificate of CA that issued our locally-significant certificate

An error occurred while installing the certificate of our issuing CA. When this error occurs the locally-significant certificate will be discarded and CTS will continue to use its password credentials for authentication.

-

-

CTS-3-LSC_ENROLL_FAIL

3-Error

Failed to set re-enrollment attributes for CTS locally-significant certificate.

An error occurred while setting the re-enrollment attributes for the new CTS certificate. When this error occurs the new certificate will be discarded and CTS will continue to use its password credentials for authentication.

-

-

CTS-5-PASSWORD_CHANGE_ONE

5-Notice

CTS password in the keystore has been renamed \[chars]\.

An MSCHAPv2 change-password sequence has been successfully executed and the old password is being renamed for fallback use. This is the first of a 2-part operation. Next the new password will be renamed to become the active password.

-

-

CTS-5-PASSWORD_CHANGE_TWO

5-Notice

A new CTS password has been installed as \[chars]\ in the keystore.

A new CTS password has been installed in the keystore following a successful MSCHAPv2 change-password sequence. The old password has been saved for fallback use.

-

-

CTS-4-NO_PROV_SECRET

4-Warning

No shared secret available for provisioning PAC from server [inet].

We are unable to provision or reprovision a CTS PAC because we do not have a configured RADIUS shared secret for the server and there are no valid unexpired PACs that can be used to secure the re-provisioning exchange.

-

-

CTS-1-CTS_CRED_ACTION_NEEDED

1-Alert

CTS credentials are missing or inconsistent in the redundant keystore.\n Please re-configure cts credentials or execute cts change-password.

A redundant keystore was detected as either not containing any CTS credentials or having a different set of credentials as contained in the active keystore. This means that CTS authentication will fail upon switchover unless remedial action is taken before then. Either use the \cts credentials ...\ CLI to re-configure the CTS device-id and password or use the \cts change-password ...\ CLI to initiate a password change with the AAA server. Either of these actions will cause the device-id and password to be inserted in both the active and redundant keystores.

-

-

CTS-6-PAC_PROVI_SUCCESS

6-Information

PAC Provisioning succeeded for [inet] A-ID=[chars]

PAC Provisioning succeeded

-

LOG_STD_NO_ACTION

CTS-3-PAC_PROVI_FAIL

3-Error

PAC Provisioning failed for [inet]

PAC Provisioning failed

-

LOG_STD_ACTION

CTS-0-CTS_EMERG

0-Emergency

[chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-1-CTS_ALERT

1-Alert

[chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-2-CTS_CRIT

2-Critical

[chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-CTS_ERR

3-Error

[chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-4-CTS_WARNING

4-Warning

[chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-5-CTS_NOTICE

5-Notice

[chars]

Normal but significant conditions

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-6-CTS_INFO

6-Information

[chars]

Informational messages

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-7-CTS_ASSERT

7-Debug

Assertion Failure [chars] @[chars]:[dec] : [chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-SAP_NIST_RNG_FAILED

3-Error

Failed to obtain random number from CTR-DRBG block for SAP key-counter. Number of consecutive failures[dec]

The system failed to obtain a random number for the SAP key counter which causes SAP session failure

-

LOG_STD_ACTION

CTS-6-SAP_REKEY_TIMER_EXPIRED

6-Information

SAP Rekey Timer Expired for interface[chars] after [dec]

SAP Rekey Timer Expired.

-

LOG_STD_NO_ACTION

CTS-3-SAP_CIPHER_MISMATCH

3-Error

Cipher suite mismatch from peer on int[chars]

SAP cipher list mismatch on the interface configured with CTS SAP. Both ends of the CTS SAP link must have matching Cipher list

-

LOG_STD_ACTION

CTS-6-SAP_DOT1X_PMKID_MISMATCH

6-Information

PMKID Mismatch on int[chars] received: %08x %08x %08x %08x

The PMKID received from peer is different from the expected PMKID

-

LOG_STD_ACTION

CTS-3-SAP_MANUAL_PMKID_MISMATCH

3-Error

PMKID Mismatch on int[chars] received: %08x %08x %08x %08x

The PMKID received from peer is different from the expected PMKID

-

LOG_STD_ACTION

CTS-6-SAP_SUCCESS

6-Information

SAP Success for int[chars] selected cipher[chars] version[dec]

-

-

-

CTS-6-SAP_NEG_DOWNREV

6-Information

SAP negotiation for int[chars] switching from version[dec] to peer's version[dec]

-

-

-

CTS-6-SAP_NEG_DOWNREV_RESTART

6-Information

SAP negotiation for int[chars] - Received message 2 with lower version[dec]

SAP negotiation switching to peer's lower version restarting message 1

-

LOG_STD_NO_ACTION

CTS-3-SAP_NEG_VERSION_MISMATCH

3-Error

SAP negotiation error for int[chars] - Received message 2 with higher

SAP negotiation error - peer's version higher than local version

-

LOG_STD_NO_ACTION

CTS-3-INVALID_ACL

3-Error

Access-list [chars] invalid for CTS policy: [chars].

An access-list configured as defining CTS L3 traffic or exemption policy cannot be used because of the specified reason.

-

-

CTS-3-ACL_UNCONFIGURED

3-Error

Access-list [chars] has been dynamically unconfigured from CTS policy because it has been [chars].

An access-list configured as defining CTS L3 traffic or exemption policy has been deleted or modified so that it can no longer be used for defining CTS policy. It has therefore been removed from the CTS layer3 policy configuration.

-

-

CTS-3-POLICY_INSTALL_FAIL

3-Error

An error occurred while trying to program the hardware error code [dec]

An error occurred while trying to program the hardware to implement the configured policy.

-

-

CTS-3-SEND_FAILED

3-Error

CTS HA failed to send checkpoint message. CTS component Id [dec] message Id [dec] header size [dec] max header size [dec] message size [dec] max size [dec].

The CTS HA client failed to send a checkpoint CTS state between the active device and the standby device is not identical.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-RECEIVE_FAILED

3-Error

CTS HA failed to process message recieved from Active device. CTS component Id [dec] message Id [dec] max header size [dec] size [dec] max message size [dec].

CTS HA client on Standby device failed to process checkpoint message. CTS state between the active device and the Standby device is not identical.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-CHKPT_REG_FAIL

3-Error

CTS HA add CTS checkpoint client failure.

CTS HA failed to add checkpoint client. No CTS data will be synced to Standby in this case.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-6-HA_ENV_DATA_STALE

6-Information

CTS HA environment-data sync failed. Old environment-data is stale.

The CTS HA environment-data sync to standby failed. CTS environment download could be in progress and old data is stale.

-

LOG_STD_NO_ACTION

CTS-4-INT_ERR

4-Warning

[chars]

CTS_INTERNAL_ERROR

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-3-SXP_CONN_STATE_CHG_OFF

3-Error

Connection [chars]<[inet] [inet]>-[dec] state changed from [chars] to Off.

SXP Connection with the specified instance number changed state.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_CONN_STATE_CHG

6-Information

Connection [chars]<[inet] [inet]>-[dec] state changed from [chars] to [chars].

SXP Connection with the specified instance number changed state.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_DFT_PASSWORD_CHANGE

5-Notice

CTS SXP password changed.

The SXP system password has been changed.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_DFT_KEYCHAIN_CHANGE

5-Notice

CTS SXP key-chain changed.

The SXP system key-chain has been changed.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_DFT_SRCIP_CHG

5-Notice

SXP default source IP is changed [inet] --> [inet].

SXP default source IP is changed on this device.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_STATE_CHANGE

5-Notice

CTS SXP [chars]

The SXP feature has changed operational state. SXP feature is functioning only when the feature is enabled.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_TIMER_START

6-Information

Connection [chars]<[inet] [inet]> [chars] timer started.

The specified SXP timer started.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_TIMER_STOP

6-Information

Connection [chars]<[inet] [inet]> [chars] timer stopped.

The specified SXP timer stopped.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_BINDING_ERR

6-Information

Binding [chars]<[chars] [chars]>-<[inet] [dec]> [chars]

SXP binding update error.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-6-SXP_CONFIG

6-Information

Connection [chars]<[inet][inet]> [chars]

A SXP configuration error occurred. The connection can not be setup correctly.

CTS_DDTS_COMPONENT

"Ensure that the connection configure on both ends" " have the matched mode IP addresses."

CTS-3-SXP_LISTENER

3-Error

Fail to start global listening socket after TCP process restart.

SXP on this device can not accept SXP connection setup request from the remote devices.

CTS_DDTS_COMPONENT

"Disable and enable SXP feature to see if the global" " listening socket can be restarted."

CTS-3-SXP_MSG_PARSE

3-Error

Connection [chars]<[inet] [inet]> [chars]

An error occurred while parsing SXP message.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-6-SXP_SRC_IP

6-Information

Source IP address [chars] [inet] does not belong to this device.

-

-

-

CTS-6-SXP_PEER_IP

6-Information

Peer IP address [chars] [inet] belongs to this device.

-

-

-

CTS-5-SXP_VRF_DEL

5-Notice

SXP Connection <[inet] [inet]> configuration in VRF:[chars] is removed.

A VRF is removed the connections configured in this VRF should be removed.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-4-SXP_INTERNAL

4-Warning

CTS SXP [chars]

The CTS SXP system encountered internal failure.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-5-SXP_BINDING_REQ

5-Notice

SXP received binding forwarding request [chars] binding [chars]<[chars] [chars]>.

SXP received a binding forwarding request.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_BINDING_FWD

5-Notice

Binding [chars]<[chars] [chars]>-<[inet] [dec]> is forwarded to the peer.

SXP forwarded binding to the peer.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_BINDING_CHG

5-Notice

Binding [chars]<[chars] [chars]>-<[inet] [dec]> changed: old connection instance number:[dec] old sgt:[chars].

Binding changed in the SXP database.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_BINDING_DEL

5-Notice

Binding [chars]<[chars] [chars]>-<[inet] [dec]> deleted in SXP database.

Binding deleted in the SXP database.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_BINDING_ADD

5-Notice

Binding [chars]<[chars] [chars]>-<[inet] [dec]> added to SXP database.

Binding added to the SXP database.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_BINDING_UPD

5-Notice

Binding [chars]<[chars] [chars]> [chars]. Update binding manager.

SXP updated binding manager with the binding change.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_BINDING_CONFLICT

5-Notice

Binding [chars]<[chars] [chars]> from peer [inet] change to new sgt [chars] from peer [inet]

SXP received conflicting sgt value from different SXP peer for the same IP prefix.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-1-SXP_BINDING_EXP

1-Alert

Binding [chars]<[chars] [chars]> can't be expanded. Expanded [dec] and maximum allowed is [dec]\n Binding propagated in the network is not consistent.

SXP expasion exceed maximum allowed.\n Binding propagated in the network is not consistent.\n User should remove the subnet binding.

CTS_DDTS_COMPONENT

"Remove this subnet if possible"

CTS-3-SXP_NODE_ID_CHG

3-Error

SXP Node ID changed from 0x%08X to 0x%08X

SXP Node ID changed.

CTS_DDTS_COMPONENT

"Make sure SXP bindings that use old node ID are removed from the binding database in all SXP nodes before the new node ID is used."

CTS-4-SXP_STALE_NODE_ID_CFG

4-Warning

Interface configuration is changed may cause adverse affect on SXP functionality

Change in interface configuration causing device to hold stale SXP Node ID.

CTS_DDTS_COMPONENT

"Make sure to re-configure SXP Node ID."

CTS-4-SXP_STALE_NODE_ID_GEN

4-Warning

Interface configuration is changed may cause adverse affect on SXP functionality

Change in interface configuration causing device to hold stale SXP Node ID.

CTS_DDTS_COMPONENT

"Make sure to disable and then enable SXP global feature."

CTS-6-SXP_FILTER_COUNT_LOWER_THRESHOLD

6-Information

SXP filter rules dropped below [[dec]%%] threshold. Reached count of [dec] out of [dec]

SXP Filter count on the box dropped below lower threshold.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_FILTER_COUNT_CHG

6-Information

CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec]

SXP Filter count on the box changed.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_FILTER_COUNT_UPPER_THRESHOLD

5-Notice

CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec]

SXP Filter count on the box exceeded upper threshold.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_FILTER_COUNT_REACHED_MAX

5-Notice

Reached maximum filter count. Could not add new filter

SXP Filter count on the box reached the maximum.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_FILTER_RULE_COUNT_LOWER_THRESHOLD

6-Information

SXP filter rules dropped below [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars].

SXP Filter rule count on the box exceeded upper threshold.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-SXP_FILTER_RULE_COUNT_CHG

6-Information

CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars].

SXP Filter rule count on the box changed.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_FILTER_RULE_COUNT_UPPER_THRESHOLD

5-Notice

CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars].

SXP Filter rule count on the box exceeded upper threshold.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-SXP_FILTER_RULE_COUNT_REACHED_MAX

5-Notice

Reached maximum filter rules. Could not add new rule in filter [chars]

SXP Filter rule count on the box reached the maximum.

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-3-CACHE_INVALID_IFS

3-Error

Cache Invalid IFS: Error opening [chars] - [chars]

Failure in validating file system. Cache file will not be opened for read/write and CTS cache functionality will not work as expected.

-

LOG_STD_ACTION

CTS-3-CACHE_INVALID_DIRECTORY_PATH

3-Error

Cache Invalid Directory Path: [chars] exceeds maximum allowed length [dec]

Cache invalid directory path. Cache file will not be opened for read/write and CTS cache functionality will not work as expected.

-

_ACTION

CTS-3-CACHE_FILE_OPEN_FAILED

3-Error

Failed to open cache file: [chars] error: [chars]

Cache file could not be opened for read CTS cache functionality will not work as expected.

-

LOG_STD_ACTION

CTS-2-CACHE_FILE_CHUNK_ALLOC_FAILURE

2-Critical

Failed to allocate memory for CTS Cache Filename chunks.

Failed to allocate memory for CTS Cache Filename chunks This is an indicator of a critical memory issue.

-

LOG_STD_ACTION

CTS-3-CACHE_READ_BAD_FILE_MAGIC

3-Error

Cache read failed due to bad file magic.

Cache read failed due to bad file magic. CTS cache functionality will not work as expected.

-

LOG_STD_ACTION

CTS-3-CACHE_READ_FILE_HEADER_ERROR

3-Error

Cache read of file [chars] failed due to file header error.

Cache read failed due to file header error. CTS cache functionality will not work as expected.

-

LOG_STD_ACTION

CTS-3-CACHE_READ_CRC_ERROR

3-Error

Cache read failed due to mismatch in CRC - file CRC[hec] calculated CRC[hec]

-

-

-

CTS-3-ENTROPY_SRC_FAILURE

3-Error

Entropy source failed health test

The periodic health tests done on the CTR-DRBG crypto implementation indicated an error in obtaining entropy. Recommended action is to crash.

-

-

CTS-6-FIPS_SW_POST_PASS

6-Information

Software crypto POST PASS

All power-up software crypto algorithmic known answer tests have passed.

-

LOG_STD_NO_ACTION

CTS-2-FIPS_SW_POST_FAIL

2-Critical

Software crypto POST Failure

One or more power-up software crypto algorithmic known answer tests have failed.

-

LOG_STD_ACTION

CTS-3-FIPS_SW_SEND_POST_RESULT_FAIL

3-Error

Software crypto POST FAIL SCP message send failed

Power-up crypto software algorithmic tests have failed and the SCP message

-

LOG_STD_ACTION

BD_VIF-5-CREATE_DELETE

5-Notice

Interface [chars] is [chars]

BD-VIF interface create/delete events.

l2-bdomain

LOG_STD_NO_ACTION

BDI_IF-5-CREATE_DELETE

5-Notice

Interface [chars] is [chars]

BDI interface create/delete events.

l2-bdomain

LOG_STD_NO_ACTION

BDOMAIN-3-MAT_BE_INIT_FAIL

3-Error

Bridge-domain MAC Table back-end subsystem did not initialize correctly Reason: [chars].

An internal software error occurred.

ether-infra

LOG_STD_ACTION

BDOMAIN-3-MAT_BE_DEL_FAIL

3-Error

Bridge-domain back-end subsystem failed to delete BD [dec] MAC Table entry [chars] Reason: [chars].

An internal software error occurred.

ether-infra

LOG_STD_ACTION

BDOMAIN-3-MACSEC_BE_INIT_FAIL

3-Error

Bridge-domain MAC Security back-end subsystem did not initialize correctly Reason: [chars].

An internal software error occurred.

ether-infra

LOG_STD_ACTION

BDOMAIN-3-STAMAC_BE_INIT_FAIL

3-Error

Bridge-domain Static MAC back-end subsystem did not initialize correctly Reason: [chars].

An internal software error occurred.

ether-infra

LOG_STD_ACTION

BDOMAIN-3-STAMAC_SSP_SSO_STAMAC_CFG_FAIL

3-Error

Standby-SP cannot configure Static MAC to back-end subsystem after reaching SSO mode Reason: [chars].

An internal software error occurred.

ether-infra

LOG_STD_ACTION

BDOMAIN-3-PP_VFI_CFG_FAIL

3-Error

Unable to add this neighbor to the target bridge-domain Reason: [chars].

An internal software error occurred.

ether-infra

LOG_STD_ACTION

BDOMAIN-4-MAC_LIMIT_VIOL_SYS_LIMIT

4-Warning

Attempt to learn a new MAC on [chars] caused system limit [dec] to be exceeded.

It is not allowed to learn addresses beyond the system limit. A service instance received a frame with unknown source MAC address and if this address is learnt it would cause the system limit to be exceeded. The address has not been learnt.

ether-infra

-

BDOMAIN-4-MAC_LIMIT_VIOL_BD_LIMIT

4-Warning

Attempt to learn a new MAC on [chars] caused configured bridge-domain limit [dec] to be exceeded.

The bridge-domain specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. A service instance belonging to this bridge-domain received a frame with unknown source MAC address and if this address is learnt it would cause the bridge-domain limit to be exceeded. The address has not been learnt.

ether-infra

-

BDOMAIN-4-MAC_LIMIT_VIOL_INST_LIMIT

4-Warning

Attempt to learn a new MAC on [chars] caused configured service instance limit [dec] to be exceeded.

The ethernet service instance specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. This service instance received a frame with unknown source MAC address and if this address is learnt it would cause the limit to be exceeded. The address has not been learnt.

ether-infra

-

MACSEC-3-VIOLATION_SHUT_INST_LIMIT

3-Error

Attempt to learn [enet] on [chars] caused configured service instance limit [dec] to be exceeded. Service instance will be shutdown.

-

-

-

MACSEC-4-VIOLATION_RESTR_INST_LIMIT

4-Warning

Attempt to learn [enet] on [chars] caused configured service instance limit [dec] to be exceeded.

The ethernet service instance specified in the system message has been configured for restrict-mode MAC Security and is not allowed to learn addresses beyond the limit specified in the system message. This service instance received a frame with unknown source MAC address and if this address is learnt it would cause the limit to be exceeded. The address has not been learnt.

ether-infra

-

MACSEC-3-VIOLATION_SHUT_INST_DENIED

3-Error

Attempt to learn denied address [enet] on [chars]. Service instance will be shutdown.

The ethernet service instance specified in the system message has been configured for shutdown-mode MAC Security and has been configured to deny the MAC address specified in the system message. A frame was received from this denied MAC address. The address has not been learnt and additionally the service instance has been shutdown.

ether-infra

-

MACSEC-4-VIOLATION_RESTR_INST_DENIED

4-Warning

Attempt to learn denied address [enet] on [chars].

The ethernet service instance specified in the system message has been configured for restrict-mode MAC Security and has been configured to deny the MAC address specified in the system message. A frame was received from this denied MAC address. The address has not been learnt.

ether-infra

-

MACSEC-4-VIOLATION_RESTR_BD_LIMIT

4-Warning

Attempt to learn [enet] on [chars] caused configured bridge-domain limit [dec] to be exceeded.

The bridge-domain specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. A service instance belonging to this bridge-domain received a frame with unknown source MAC address and if this address is learnt it would cause the bridge-domain limit to be exceeded. The address has not been learnt.

ether-infra

-

MACSEC-4-VIOLATION_RESTR_SYS_LIMIT

4-Warning

Attempt to learn [enet] on [chars] caused system limit [dec] to be exceeded.

It is not allowed to learn addresses beyond the system limit. A service instance received a frame with unknown source MAC address and if this address is learnt it would cause the system limit to be exceeded. The address has not been learnt.

ether-infra

-

MACSEC-4-VIOLATION_RESTR_SYS_CFG_LIMIT

4-Warning

Attempt to learn [enet] on [chars] caused system limit [dec] to be exceeded.

It is not allowed to learn addresses beyond the system limit that allows number of permitted + sticky addresses to be configured in the system. A service instance received a frame with unknown source MAC address and if this address is learnt it would cause the system limit to be exceeded. The address has not been learnt.

ether-infra

-

MACSEC-3-VIOLATION_SHUT_RELEARN

3-Error

Attempt to move [enet] from [[chars]] to [[chars]] shutting down the latter

The MAC address specified in the system message is currently learned on the first ethernet service instance specified in the system message. An ethernet frame with the same MAC address has now been encountered on the second ethernet service instance. This is a violation of MAC Security policy and as a result the second service instance will be shut down.

ether-infra

"If the MAC address has to be permitted to be re-learnt on the second " "service instance remove the address from the list of addresses " "permitted on the first service instance if applicable and clear the "

MACSEC-3-VIOLATION_RESTR_RELEARN

3-Error

Attempt to move [enet] from [[chars]] to [[chars]]

The MAC address specified in the system message is currently learned on the first ethernet service instance specified in the system message. An ethernet frame with the same MAC address has now been encountered on the second ethernet service instance. This is a violation of MAC Security policy.

ether-infra

"If the MAC address has to be permitted to be re-learnt on the second " "service instance remove the address from the list of addresses " "permitted on the first service instance if applicable and clear the "

BDOMAIN_BE_SW-3-REM_MAC_ENTRY_FAILED

3-Error

Unable to remove MAC entry [enet] in bridge-domain [dec]

The bridge-domain was unable to remove the learned MAC address entry from it's database.

ether-infra

"If the error persists the router may need to " "be reloaded"

BDOMAIN_BE_SW-4-PORT_MAX_MAC_ENTRIES

4-Warning

The port [chars] has reached the maximum number of learned MAC entries [dec]

The specified port has reached the maximum number of learned MAC entries. It will not learn more until some of the entries are removed. This may happen when the entries age out. If this error persists it may indicate that there are too many nodes on the specified port or that the age out timer is too long.

ether-infra

"MAC entries should be removed by the system as " "they age out. No action is required."

BDOMAIN_BE_SW-3-PORT_MACS_NOT_ZERO

3-Error

The port [chars] is being removed while MAC entries still exist

The specified port is being removed before all learned MAC entries have been removed.

ether-infra

"If other error messages related to removing MAC " "entries have been reported then copy those down " "exactly. Contact your Cisco technical support " "representative and provide the gathered " "information."

BDOMAIN_BE_SW-3-BDI_ENCAP_NOT_SUPPORTED

3-Error

BDI Encap is not supported in IOL use EFP to pop vlan tags

-

-

-

BDOMAIN_BE_SW-3-L2FIB_ENTRY_INVALID

3-Error

Null SW Handle from L2FIB [chars]

The bridge-domain receives a null handle from L2FIB

l2fib

"If the error persists the router may need to " "be reloaded"

BDOMAIN_BE_SW-3-L2FIB_ENTRY_GENERAL

3-Error

[chars]

The bridge-domain receives wrong info from L2FIB

l2fib

"If the error persists the router may need to " "be reloaded"

MRP-2-RINGFAULT

2-Critical

Ring [dec]: The MRP ring is now in FAULT state

The MRP ring is in FAULT state. This typically happens if a link or node in the ring goes down.

accsw-layer2

"Determine the location of the fault and restore " "connectivity. The ring should resume functioning " "automatically"

MRP-6-RINGNORMAL

6-Information

Ring [dec]: The MRP ring is now in NORMAL state [chars] is Blocked

The state of the MRP ring has changed to NORMAL.

accsw-layer2

"This is an informational message. The device is " "functioning as expected."

MRP-6-RINGNORMAL_RECEIVED

6-Information

Ring [dec]: The MRP ring is now in NORMAL state

The state of the MRP ring has changed to NORMAL.

accsw-layer2

"This is an informational message. The device is " "functioning as expected."

MRP-6-MODE_MANAGER_DEPRECATED

6-Information

MRP \mode manager\ is deprecated executing \mode auto-manager\ instead.

MRP mode manager is no longer supported and is replaced by mode auto-manager.

accsw-layer2

"This is an informational message. The device is " "functioning as expected."

DIAG-6-BYPASS

6-Information

[chars]: Diagnostics is bypassed

This is an informational message stating that diagnostics testing was not performed on the card because diagnostic testing was disabled in the user configuration.

gold

"This behavior is consistent with the user configuration and no action " "needs to be taken. If you want to run bootup diagnostics enable bootup" " diagnostics by using the diagnostic bootup command."

DIAG-6-RUN_MINIMUM

6-Information

[chars]: Running Minimal Diagnostics...

Minimum Diagnostic is running on the card

gold

"Nothing. This is an informational message and the system is working " "properly."

DIAG-6-RUN_COMPLETE

6-Information

[chars]: Running Complete Diagnostics...

Complete Diagnostic is running on the card

gold

"Nothing. This is an informational message and the system is working " "properly."

DIAG-6-DIAG_OK

6-Information

[chars]: Passed [chars]

The diagnostic tests did not detect any error on the card.

gold

"Nothing. This is an informational message stating that the line card " "passed the diagnostic tests."

DIAG-3-MINOR

3-Error

[chars]: [chars] detected a Minor Error. Please use 'show diagnostic result <target>' to see test results.

A minor error was detected during diagnostic testing.

gold

"Re-seat the card and retry the test. If the same result occurs after " "reseating the card and retrying the test copy the error message " "exactly as it appears on the screen and gather the output of show " "tech-support and any other relevant information. Contact your " "technical support representative with the gathered information."

DIAG-3-MAJOR

3-Error

[chars]: [chars] detected a Major Error. Please use 'show diagnostic result <target>' to see test results.

A major error was detected during diagnostic testing.

gold

"Re-seat the card and retry the test. If the same result occurs after " "reseating the card and retrying the test copy the error message " "exactly as it appears on the screen and gather the output of show " "tech-support and any other relevant information. Contact your " "technical support representative with the gathered information."

DIAG-6-TEST_RUNNING

6-Information

[chars]: Running [chars]{ID=[dec]} ...

Diagnostic testing is running a test on the card

gold

"Nothing. This is an informational message and the system should be " "working properly."

DIAG-6-TEST_OK

6-Information

[chars]: [chars]{ID=[dec]} has completed successfully

Diagnostic testing was completed and no errors were found on the line card.

gold

"This is an informational message indicating that Field Diagnostic " "testing has completed successfully. The system is working properly and " "no action is required based on this error message."

DIAG-3-TEST_FAIL

3-Error

[chars]: [chars]{ID=[dec]} has failed. Error code = 0x[hec] [chars]

A diagnostic test has found an error on the line card.

gold

"Ensure the line card is firmly in the slot reseat if necessary and " "attempt to run the test again if the line card is not seated properly " "in the slot. If the line card was properly seated in the slot copy the " "error message exactly as it appears on the console gather the output " "of show tech-support and contact your Cisco technical support " "representative with the gathered information."

DIAG-3-TEST_SKIPPED

3-Error

[chars]: [chars]{ID=[dec]} is skipped

The specified diagnostic test cannot be run.

gold

"Nothing. Although the test cannot be run this message does not indicate " "a problem."

DIAG-3-TEST_NOT_SUPPORT

3-Error

[chars]: [chars]{ID=[dec]} is not supported

The diagnostic test is not supported on current chassis configuration.

gold

"Nothing. The test cannot be run but this message does not indicate a " "problem with the system."

DIAG-6-SCHED_RUNNING

6-Information

[chars]: Performing Scheduled Online Diagnostic...

The scheduled diagnostic test is running.

gold

"Nothing. The diagnostic test is being run as configured and the system " "is working properly."

DIAG-6-SCHED_COMPLETE

6-Information

[chars]: Scheduled Online Diagnostic is completed

The scheduled Diagnostic test is complete.

gold

"Check the results and proceed accordingly. This is an information " "message only to indicate that Diagnostic testing is complete. The router " "is working properly and no action is needed based on this message."

DIAG-3-CREATE_PROCESS_FAIL

3-Error

Create process [chars] failed

An internal software error occurred.

gold

"Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information."

DIAG-3-ENQUEUE_FAIL

3-Error

[chars]: process_enqueue failed

An internal software error occurred.

gold

"Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information."

DIAG-3-SET_ARGU_FAIL

3-Error

Set argument failed

An internal software error occurred.

gold

"Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information."

DIAG-3-GET_ARGU_FAIL

3-Error

Get argument failed

An internal software error occurred.

gold

"Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information."

DIAG-3-CARD_ABSENT

3-Error

[chars] is not detected

A line card could not be located in a slot where a diagnostic action was requested.

gold

"Ensure the targeted line card is properly seated in the specified slot. " "If the line card is properly seated ensure the correct slot was " "indicated in the command-line interface. If the line card is well-seated " "and the correct slot was specified copy the error message exactly as it " "appears on the screen as well as the output of show tech-support and " "paste the output into a separate file. Contact your technical support " "representative with the gathered information."

DIAG-3-DIAG_RUNNING

3-Error

[chars]: Diagnostic is currently running

A diagnostic test is currently being run on the specified card and additional tests cannot be run until the previously requested tests have been completed.

gold

"The system is working properly and no user action is required. If you " "want to run the specified diagnostic test either wait for the current " "diagnostic test to finish and then run the test or stop the current " "test and run the new test."

DIAG-3-NO_DIAG_RUNNING

3-Error

[chars]: Diagnostic is not running

An attempt to stop a diagnostic test that was not running was made.

gold

"None. This is an informational message."

DIAG-6-DIAG_STOPPED

6-Information

[chars]: Diagnostic is stopped.

Diagnostic test has stopped.

gold

"Nothing. This is an informational message stating that diagnostic " "testing has been stopped. If you want the test to run to completion " "rerun the test."

DIAG-6-NO_TEST

6-Information

[chars]: No test to run

The diagnostic test cannot find tests to run.

gold

"In some cases on some platforms a Field Diagnostic image needs to be " "loaded onto the line card if you want to run the test. If applicable " "download a Field Diagnostic image onto the line card. In other cases " "the test is simply not available. This message is an informational and " "does not require user action."

DIAG-3-INVALID_TEST

3-Error

Invalid test: [chars]

A test that does not exist was requested.

gold

"Ensure the specified test is supported by the line card. The " "list of available tests and their associated test IDs can be retrieved " "using show diagnostic content."

DIAG-3-INVALID_PORT

3-Error

Invalid port number : [chars]

A diagnostic request is being made on a port that does not exist.

gold

"Ensure the specified port number exists and that the correct port number " "is being specified."

DIAG-3-INVALID_DEVICE

3-Error

Invalid device number : [chars]

A diagnostic request is being made on a device that does not exist

gold

"Ensure that the specified device number 1-based exists and is valid"

DIAG-6-SCHED_STOPPED

6-Information

[chars]: Scheduled Online Diagnostic is stopped

The scheduled Diagnostic test has been stopped.

gold

"If you do not want the test to run nothing. If you want the test to " "run schedule the test or run the test manually."

DIAG-3-UNKNOWN_OPCODE

3-Error

[chars]: Unknown opcode %ld is received

An internal software error occurred.

gold

"Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information."

DIAG-6-SKIP_ONDEMAND_STANDBY_CARD_TEST

6-Information

[chars]: [chars] cannot be executed.

The specified test can only be run on a standby supervisor from the standby supervisor.

gold

"Nothing. The test cannot be run but the system is working properly."

DIAG-6-SKIP_ONDEMAND_ACTIVE_TO_STANDBY_TEST

6-Information

[chars]: [chars] cannot be executed for active device.

The specified test can only be run from the active supervisor to test standby supervisor.

gold

"Nothing. The test cannot be run but the system is working properly."

DIAG-6-SCHEDULE_IS_REMOVED

6-Information

[chars]: Schedule Diagnostic for [[chars] [chars] %2ld:%02ld.] is removed

The scheduled online diagnostic tests are no longer configured. This message usually appears after a scheduled test is removed by the user or a card is removed from the chassis.

gold

"If you want the scheduling tests to be removed nothing. If you want " "the scheduled tests to still be run reconfigure the scheduled tests."

DIAG-3-MONITOR_INTERVAL_ZERO

3-Error

[chars]: Monitoring interval is 0. Cannot enable monitoring for Test #[dec]

Health Monitoring cannot be enabled for the specified test because the interval for the test has been set to 0.

gold

"If you are comfortable not running the specified health monitoring test " "nothing. If you would like to enable the specified test for health " "monitoring reset the interval to a number other than 0."

DIAG-3-ALWAYS_ENABLE_TEST

3-Error

[chars]: The users are not allow to disable monitoring for Test #[dec]

The specified health monitoring test must be run and cannot be disabled.

gold

"Nothing. The specific health monitoring test cannot be disabled by " "design. The system is working properly."

DIAG-3-FIXED_INTERVAL_TEST

3-Error

[chars]: The users are not allow to change monitoring interval of Test #[dec]

The specified health monitoring test interval is not user-configurable and therefore cannot be changed.

gold

"Nothing. The specific health monitoring interval is not user-" "configurable by design so nothing can be done to change the interval."

DIAG-3-NOT_MONITORING_TEST

3-Error

[chars]: The test:[dec] cannot be used as health monitoring test

The specified test number cannot be used as a health monitoring test.

gold

"Nothing. The system is working properly and the specified test cannot " "be configured as a health monitoring test."

DIAG-3-INVALID_MONITORING_INTERVAL

3-Error

[chars]: The [chars][ID=[dec]] monitoring interval must be at least %lld millisec

The specified test monitoring interval is too small.

gold

"The system is working properly and no user action is required. If you " "want to specify a smaller testing interval the error message text " "provides the lowest possible configurable interval for the specified " "monitoring interval."

DIAG-3-MONITOR_DISABLE

3-Error

[chars]: Monitoring test:[dec] is disabled since default interval is zero

The specified test is no longer a health monitoring test because health monitoring has been disabled.

gold

"The system is working properly and no user action is required. If you " "want the requested test to be a health monitoring test enable health " "monitoring and ensure your test is enabled as a health monitoring test."

DIAG-6-TEST_SKIPPED_FROM_ACTIVE

6-Information

[chars]: [chars] cannot be executed from active supervisor.

The specified test cannot be run from active supervisor.

gold

"Nothing. The test cannot be run but the system is working properly."

DIAG-6-SIMULATED_TEST_RESULT

6-Information

[chars]: [chars] test result is simulated.

The specified test's result is simulated. The failure does not indicate software nor hardware fault

gold

"Nothing. The test failure is simulated as specified by the user."

DIAG-4-CONFIG_REAPPLY

4-Warning

Please reapply config command '[chars]' after the card is online.

The specified config command cannot be applied.

gold

"The system is working properly and the specified command cannot" "be applied. Please reapply the config command after the module" "is online."

IPV6_ND-4-INTFLIMIT

4-Warning

Attempt to exceed interface limit on [chars] for %P

An ND resolution request was received on the specified interface for the specified destination. Satisfying the request would have exceeded the ND cache entry limit configured on the interface. The request was ignored

ipv6

"No action is necessary. Review the interface" " ND cache entry limit configured via" " ipv6 nd cache interface-limit if appropriate"

IPV6_ND-4-DUPLICATE

4-Warning

Duplicate address %P on [chars]

Another system is using your IPv6 address.

ipv6

"Change the IPv6 address of one of the " "two systems."

IPV6_ND-4-DUPLICATE_OPTIMISTIC

4-Warning

Duplicate address %P on [chars]

You have elected not to run DAD but another system is using your IPv6 address.

ipv6

"Change the IPv6 address of one of the " "two systems."

IPV6_ND-6-DUPLICATE_INFO

6-Information

DAD attempt detected for %P on [chars]

Another system attempted to configure an IPv6 address already configured on this interface. The configuration of the other system was denied.

ipv6

"No action is required on this system."

IPV6_ND-4-LOOPBACK

4-Warning

Looped back NSDAD packet detected for %P on [chars]

A looped back DAD NS packet was detected for %P on [chars]

ipv6

"A neighbor solicitation packet was received for an " "address on which this router is performing duplicate " "address detection. The packet was ignored because it " "originated from this router and was looped back."

IPV6_ND-3-CONFLICT

3-Error

Router %P on [chars] conflicting ND setting [chars]

Another router on the link sent router advertisements\n\ with conflicting parameters to ours.

ipv6

"Verify that all IPv6 routers on the link have the same parameters\n\ in the router advertisement for hop-limit managed-config-flag\n\ other-config-flag reachable-time and ns-interval and that\n\ preferred and valid lifetimes for the same prefix advertised\n\ by several routers are the same. Use the command show ipv6 interface\n\ to list the parameters per interface."

IPV6_ND-3-ND_ROUTER_NUM

3-Error

Router list not empty [dec]. Recounting routers autocorrecting

There is a missmatch between the number of routers known to ND and\n\ the number of routers known to the interface. The issue will\n\ auto-correct itself

ipv6

NOG_STD_NO_ACTION

IPV6_ND-6-ADDRESS

6-Information

%P/[dec] can not generate auto-configured address on [chars] [chars][chars]

IPv6 address could not be auto-configured.

ipv6

NOG_STD_NO_ACTION

IPV6_ND-3-NULLDATA

3-Error

Uninitialized data - [chars]

An IPv6 process could not be started. This machine will not be able to process any IPv6 packets.

ipv6

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPV6_ND-4-LLA_CONFLICT

4-Warning

LLA conflict for static neighbor %P on [chars] : [chars]

This error indicates that an ND message from the specified neighbor carries a Link Layer Address other than that configured via static neighbor

ipv6

"Reconfigure the static neighbor with correct LLA"

IPV6_ND-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

ipv6_nd

LOG_STD_ACTION

IPV6_ND-4-DUPOLPFX

4-Warning

Prefix %P/[dec] advertised in RA on [chars] was previously learnt on another interface

This warning indicates that an on-link prefix advertised in an IPv6 ND RA on the specified interface has previously been learnt from an RA on another interface. The prefix will be ignored on the current interface

ipv6_nd

" Learning the same on-link prefix via IPv6 ND RA" " on multiple interfaces indicates a likely" " configuration error on adjacent routers." " Review network topology and adjacent router" " configuration and correct as appropriate"

IPV6_ND-4-OLPFXCON

4-Warning

Prefix %P/[dec] advertised in RA on [chars] has been previously configured on another interface

This warning indicates that an on-link prefix advertised in an IPv6 ND RA on the specified interface has previously been configured on another interface. The prefix will be ignored on the current prefix

ipv6_nd

" Learning an on-link prefix via IPv6 ND RA" " when the same prefix has previously been" " configured on another interface indicates a" " likely configuration error either on the" " current router or on the neighbor router" " advertising the ND RA. Review network topology" " current router and adjacent router configuration" " and correct as appropriate"

IPV6_ND-4-RA_TIMERS_INCONSISTENT

4-Warning

Configured Router Advertisements interval exceeds the configured RA lifetime on [chars].

This warning indicates that the value configured for the Router Advertisements interval exceeds the value configured for Router Advertisements lifetime on the given interface. This is not recommended as it will lead to hosts timing out the router between Router Advertisement transmissions.

ipv6_nd

" Check the router configuration on the interface" " and correct it so that RA lifetime is greater" " than RA interval."

IPV6_ND-4-RESOURCE_LIMIT

4-Warning

[chars] resource limit prevents creation of ND entry

This warning indicates that an ND cache entry could not be created because the indicated platform resource limit has been reached.

ipv6_nd

"Check the size of the ND cache table. " "Consider using ND cache sizing to explicitly " "configure the size of the ND cache on each " "interface"

IPV6_ND-3-IPV6PAKENCAP

3-Error

Dest host is IPv4 in IPv6 packet - [chars]

IPv6 packet encapsulation called with IPv4 destination host

ipv6

"Use an IPv6 address in neighbour for IPv6 packet flow on the router" "if the problem persists or you feel this should be supported then " "please contact the TAC with the failing command line."

IPV6_ND-4-RSRV_ADDRESS

4-Warning

[chars]: [chars]: [chars]

IPv6 address contains reserved interface identifiers.

ipv6

NOG_STD_NO_ACTION

IPV6_ADDRMGR-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

ENTROPY-0-ENTROPY_FAILURE

0-Emergency

Unable to collect sufficient entropy

On bootup the router attempts to collect entropy to initialize its random number generator. This router has failed to do so. Because of this most security protocols will not run

-

"This is probably a hardware failure"

CRYPTO_RSA_ISSU-3-INIT

3-Error

Crypto RSA ISSU client initialization failed to [chars]. Error: [dec] [chars]

Crypto RSA ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

crypto_rsa

LOG_STD_SH_TECH_ACTION

CRYPTO_RSA_ISSU-3-TRANSFORM_FAIL

3-Error

Crypto RSA ISSU client [chars] transform failed for message type [dec].\n\ Error: [dec] [chars]

Crypto RSA ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Crypto RSA state will not\n\ be indentical with the active unit.

crypto_rsa

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

CRYPTO_RSA_ISSU-3-MSG_NOT_OK

3-Error

Crypto RSA ISSU client message type [dec] is not compatible

Crypto RSA ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it cannot be processed by this unit

crypto_rsa

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

CRYPTO_RSA_ISSU-3-MSG_SIZE

3-Error

Crypto RSA ISSU client failed to get the MTU for message type [dec].\n\ Error: [dec] [chars]

Crypto RSA ISSU client failed to calculate MTU\n\ for the message specified. The dot1x ISSU client will not\n\ be able to send message to the standby unit.

crypto_rsa

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

CRYPTO_RSA_ISSU-3-INVALID_SESSION

3-Error

Crypto RSA ISSU client does not have a valid registered session.

Crypto RSA ISSU client does not have a valid registered session.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up.

crypto_rsa

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

CRYPTO_RSA_ISSU-3-SESSION_REGISTRY

3-Error

Crypto RSA ISSU client failed to register session information.\n\ Error: [dec] [chars]

Crypto RSA ISSU client failed to register session information.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up.

crypto_rsa

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

CRYPTO_RSA_ISSU-3-SESSION_UNREGISTRY

3-Error

Crypto RSA ISSU client failed to unregister session information.\n\ Error: [dec] [chars]

Crypto RSA ISSU client failed to unregister session information.

crypto_rsa

"show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

CRYPTO_RSA_ISSU-3-SESSION_NEGO

3-Error

Crypto RSA ISSU client encountered unexpected client nego_done.\n\ Error: [dec] [chars]

Crypto RSA ISSU client encountered an unexpected 'client\n\ negotiation done'.

crypto_rsa

"show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

CRYPTO_RSA_ISSU-3-SEND_NEGO_FAILED

3-Error

Crypto RSA ISSU client failed to send negotiation message.\n\ Error: [dec] [chars]

Crypto RSA ISSU client failed to send a session negotiation\n\ message to the peer. When there is a problem in the ISSU\n\ negotiation the standby unit can not be brought up.

crypto_rsa

"show logging and show checkpoint client"

CRYPTO_RSA_ISSU-3-GET_BUFFER

3-Error

Crypto RSA ISSU client failed to get buffer for message.\n\ Error: [dec] [chars]

Crypto RSA ISSU client failed to get buffer for building\n\ a negotiation message. Hence it cannot send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

crypto_rsa

"show logging and show checkpoint client"

CRYPTO_ENGINE-4-AUDITWARN

4-Warning

Encryption audit check could not be performed

The audit check verifying encryption entitlement within the IOS image could not be performed due to incompete system configuration.

-

"Manually verify that this IOS image is entitled to contain " "encryption."

CRYPTO_ENGINE-0-AUDITFAIL

0-Emergency

Encryption audit check found the wrong level of encryption in this image

The audit check verifying encryption entitlement within the IOS image either found encryption in a non-encryption image or the wrong strength within an IOS image containing encryption. Use of the encryption may violate U.S. Export Laws and Regulations.

-

"Contact Cisco to obtain a replacement IOS image."

CRYPTO_ENGINE-5-KEY_DELETED

5-Notice

A key named [chars] has been removed from key storage

A key has been marked for removal from storage. The configuration must be saved to permanently remove this key.

-

"No action required. Informational message"

CRYPTO_ENGINE-5-KEY_ADDITION

5-Notice

A key named [chars] has been generated or imported by [chars]

An RSA or EC key has been generated or imported. The configuration must be saved to permanently save this key.

-

"No action required. Informational message"

CRYPTO_ENGINE-5-KEY_REPLACE

5-Notice

A key named [chars] has been replaced by [chars] with new key data

An RSA or EC key has been replaced. The configuration must be saved to permanently save this key.

-

"No action required. Informational message"

CRYPTO_ENGINE-3-FIPS_COMPLIANCE_FAIL

3-Error

FIPS security compliance violation is detected. Use of [chars] by [chars] is denied

A FIPS security compliance violation has been detected. The cryptography used is considered weak and violates the requiremnet set by FIPS

-

"Use FIPS approved cryptographic methods" "or disable FIPS mode and reload device"

CRYPTO_ENGINE-3-CSDL_COMPLIANCE_FAIL

3-Error

Cisco PSB security compliance violation is detected. Use of [chars] by [chars] is denied

A security compliance violation has been detected. An attempt to use cryptography [chars] that is restricted

-

"Use Cisco PSB approved cryptographic methods" "or remove the compliance profile that is active at your own risk"

CRYPTO_ENGINE-3-CSDL_COMPLIANCE_FAIL_RSA

3-Error

Cisco PSB security compliance violation is detected. Use of weak [dec] bit key is denied

A security compliance violation has been detected. An attempt to use RSA cryptography with weak keys that is restricted by Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB has been denied.

-

"Use Cisco PSB approved cryptographic methods" "or remove the compliance profile that is active at your own risk"

CRYPTO_ENGINE-4-CSDL_COMPLIANCE_DISABLED

4-Warning

Cisco PSB security compliance has been disabled

Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB has been disabled.

-

"Proceed with caution since weak cryptography will be allowed"

CRYPTO_ENGINE-5-CSDL_COMPLIANCE_ENFORCED

5-Notice

Cisco PSB security compliance is being enforced

Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB are being enforced.

-

"No action is required"

CRYPTO_ENGINE-5-CSDL_COMPLIANCE_EXCEPTION_ADDED

5-Notice

Cisco PSB security compliance exception has been added by [chars] for use of [chars]

Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB are being enforced.

-

"No action is required"

CRYPTO_ENGINE-4-CSDL_COMPLIANCE_RSA_WEAK_KEYS

4-Warning

RSA keypair [chars] is in violation of Cisco security compliance guidelines and will be rejected by future releases.

An attempt to use RSA cryptography with weak keys has been detected. Cisco recommends RSA key sizes of 2048 or greater for security. Shorter key sizes will be rejected in future releases.

-

"Regenerate keys specifying key size to be 2048 or greater" " to avoid future service disruption"

VPN_HW-6-INFO

6-Information

slot: [dec] [chars]

This is informational message from VPN hardware accelerator driver.

vpn_hw

"This is informational message from VPN_HW. This occurs " "in normal operation. No action is required."

VPN_HW-6-INFO_LOC

6-Information

Crypto engine: [chars] [chars]

This is informational message from VPN hardware accelerator driver.

vpn_hw

"This is informational message from VPN_HW. This occurs " "in normal operation. No action is required."

VPN_HW-6-SHUTDOWN

6-Information

[chars] shutting down

The specified VPN_HW is shutting down. It may have been physically removed.

vpn_hw

"This is an informational message only. It occurs " "in normal operation."

VPN_HW-1-INITFAIL

1-Alert

Slot [dec]: [chars]

The VPN hardware accelerator driver failed to initialize the accelerator at the slot specified in the error message at the specified point. This event will negatively impact encryption performance. User should reload router.

vpn_hw

LOG_STD_ACTION

VPN_HW-1-ERROR

1-Alert

slot: [dec] - [chars]

An error occured in the application using VPN_HW.

vpn_hw

"Copy the error message exactly as it appears and report it to " "your technical support representative."

VPN_HW-1-NOMEMORY

1-Alert

[chars] creation failed for slot [dec]

The VPN_HW driver in its initialization phase could not allocate memory for the data structure that is specified in the error message.

vpn_hw

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration. If this " "message recurs copy the error message exactly as it appears on the console " "or in the system log contact your Cisco techincal support " "representative and provide the representative with the gathered information."

VPN_HW-1-OWNER

1-Alert

slot: [dec]: [chars] packet buffer pak=0x%08x

A software or hardware error occurred. The VPN hardware accelerator driver has detected that the buffer ring is in an inconsistent and unrecoverable state.

vpn_hw

LOG_STD_ACTION

VPN_HW-1-ALIGN

1-Alert

Slot: [dec] - Alignment failure on packet buffer: 0x%08x

A software error occurred. The VPN hardware accelerator driver has detected that the buffer is not aligned correctly.

vpn_hw

"Copy the error message exactly as it appears and report it to " "your Cisco technical support representative."

VPN_HW-1-TOOBIG

1-Alert

Slot: [dec] - [chars] received a packet with size [dec].

Software supports upto **** MTU

vpn_hw

LOG_STD_ACTION

VPN_HW-1-UNSUPP

1-Alert

VPN Module in slot: [dec]: [chars] %08x.

This revision or version of the VPN hardware accelerator in the slot specified in the error message is not supported.

vpn_hw

"Verify the VPN hardware adapter is the proper hardware level and software " "revision for the running version of IOS. If it is " "copy the error message exactly as it appears and report it to " "your Cisco technical support representative."

VPN_HW-1-HEARTBEAT

1-Alert

VPN Module in slot: [dec]: Keepalive lost.

The VPN hardware accelerator seems to have stopped operating.

vpn_hw

"Reboot your router. If this message recurs copy the error message " "exactly as it appears on the console or in the system log contact " "your Cisco techincal support representative and provide the representative " "with the gathered information."

VPN_HW-1-PACKET_ERROR

1-Alert

slot: [dec] Packet Encryption/Decryption error [chars]

An unexpected error occurred during the encryption or decryption\n\ of a packet.

-

"This message can occur occasionally during normal operation of the " "system. It may occur during the transition to a new session key for " "a Security Association. In such cases no action is required. However " "if it happens frequently or is associated with traffic disruption then " "note of the status value and contact a Cisco representative. The " "VPN hardware accelerator will most likely need to be replaced."

VPN_HW-6-FIPSFAIL

6-Information

FIPS test_id [dec][chars] Test Failure will be induced

The FIPS test was forced to fail from ROMMON

-

"Do not set FIPS_FAIL via rommon if fips failure test is not desired"

VPN_HW-3-MULTDEV

3-Error

Cannot support more than one Encryption AIMs

A second Encryption AIM was discovered present in the system. The\n\ Encryption AIM software only supports a single Encryption AIM. All\n\ other Encryption AIMs installed will be ignored.

-

"Remove one of the Encryption AIMs installed in your system."

VPN_HW-0-SELF_TEST_FAILURE

0-Emergency

Hardware Crypto self-test failed [chars]

One of the Hardware Crypto self-tests has failed. The Crypto engine is not operable in this state.

-

"If the failure persists contact Cisco to " "replace the hardware."

ALIGN-3-SPURIOUS

3-Error

Spurious memory access made at [chars] reading 0x[hec]

An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked.

cpu

"Copy the error message exactly as it appears on the console or in the " "system log. Issue the <CmdBold>show alignment<noCmdBold> command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the <CmdBold>show alignment<noCmdBold> output call your " "Cisco technical support representative and provide the representative " "with the gathered information."

ALIGN-3-RO_WRITE

3-Error

Spurious memory access made at [chars] writing to 0x[hec]

An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked.

cpu

"Copy the error message exactly as it appears on the console or in the " "system log. Issue the <CmdBold>show alignment<noCmdBold> command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the <CmdBold>show alignment<noCmdBold> output call your " "Cisco technical support representative and provide the representative " "with the gathered information."

ALIGN-3-TRACE

3-Error

-Traceback= [chars]

A trace that shows where the previous ALIGN error occurred.

cpu

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MEMSCAN-6-SCRUBED

6-Information

Parity error0x[hec] scrubed

Memory parity error found and scrubed.

mem

"None"

MEMSCAN-6-MSCRUBED

6-Information

Parity error0x[hec] scrubed multiple times

Multiple parity errors found at this address.

mem

"Take down router and replace DRAM"

MEMSCAN-6-LINKED

6-Information

Error0x[hec] block0x[hec] linked size [dec]

A parity error was found in a free block which could not\n\be scrubbed. The Free block has been moved to a bad list so that it cannot be used again.

mem

"Schedule a reboot of the system to clear memory. If\n\more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-6-SPLIT

6-Information

Error0x[hec] block0x[hec] split bad block0x[hec] linked size 0x[hec]

A parity error was found in a free block which could not be scrubbed. The free block has been fragmented and the fragment with the parity error has been moved to a dead list so that it cannot be used again.

mem

"Schedule a reboot of the system to clear memory. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-3-INUSE

3-Error

Parity error0x[hec] found in busy bolck0x[hec]

A parity error has been found in a busy block which cannot be scrubbed nor moved to the bad list.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-3-DUPERR

3-Error

Another parity error0x[hec] found in bolck0x[hec]. Not scrubed

Multiple errors have been found in a meory block.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-3-INPREV

3-Error

Parity error0x[hec] found in block field **previous

A parity error has been found in a critical field of a block header.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-3-INHEAD

3-Error

Parity error0x[hec] found in block header

A parity error has been found in a critical field of a block header.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-3-NOHEAD

3-Error

No block header for parity error0x[hec] until 0x[hec]

A parity error has been found for an address which has no block header

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-2-TEXTREG

2-Critical

Parity error0x[hec] found in imagetext region

A parity error was found in the text region of memory.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-2-DATAREG

2-Critical

Parity error0x[hec] found in imagedata region

A parity error was found in the data region of memory.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-2-BSSREG

2-Critical

Parity error0x[hec] found in imagebss region

A parity error was found in the BSS region of memory.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

MEMSCAN-3-UNKNOWN

3-Error

Parity error0x[hec] found in otherunknown region

A parity error was found in other region of memory.

mem

"Schedule a reboot of the system to clear memory AS SOON AS POSSIBLE. If this parity error is touched in normal operation of the router the router will crash. If more parity errors are found at this address after the reboot replace the DRAM in the router or the processor board."

ALIGN-3-READEXCEPTION

3-Error

Warning : read accees failed at [chars] still continuing \n

In ls1010 read access failures do not make the box reload. They can \n\ be caused by either a bad register value in the asp ver 3.3 or earlier\n\ or a real problem in the hardware

-

"If the ASP version is 3.3 or more report it to your\n\ technical support representative."

ALIGN-3-CORRECT

3-Error

Alignment correction made at [chars] [chars]ing 0x[hec]

A software component within the router needs memory optimization.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-CORRECT_SO

3-Error

Alignment correction made at [chars] [chars]ing [chars]

A software component within the router needs memory optimization.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-FULL

3-Error

Alignment log is full - no new entries will be recorded

The router identified more software components in need of memory\n\ optimization than it can record.

cpu

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-SPURIOUS

3-Error

Spurious memory access made at [chars] reading 0x[hec]

An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked.

-

"Copy the error message exactly as it appears on the console or in the " "system log. Issue the <CmdBold>show alignment<noCmdBold> command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the <CmdBold>show alignment<noCmdBold> output call your " "Cisco technical support representative and provide the representative " "with the gathered information."

ALIGN-3-SPURIOUS_SO

3-Error

Spurious memory access made at [chars] reading [chars]

An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked.

-

"Copy the error message exactly as it appears on the console or in the " "system log. Issue the <CmdBold>show alignment<noCmdBold> command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the <CmdBold>show alignment<noCmdBold> output call your " "Cisco technical support representative and provide the representative " "with the gathered information."

ALIGN-3-TRACE

3-Error

-Traceback= [chars]

A trace that shows where the previous ALIGN error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-TRACE_SO

3-Error

-Traceback= [chars]

A trace that shows where the previous ALIGN error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-TRACEX

3-Error

[chars]

A trace that shows where the previous ALIGN error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

BCM-4-ECC_L2CACHE

4-Warning

Corrected ECC from L2 cache

A soft-parity error from the Layer 2 cache has been detected and corrected. Normal system operation should continue.

-

"If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative."

BCM-4-ECC_MEMORY

4-Warning

Corrected ECC from memory

A soft-parity error from the memory has been detected and corrected. Normal system operation should continue.

-

"If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative."

BCM-4-COR_ECC_HIGH

4-Warning

High correctable ECC error rate detected\n L2 cache data errors = [dec]\n L2 cache tag errors = [dec]\n Memory data errors = [dec]\n

A high rate of soft-parity errors from the memory has been detected. Normal system operation may be affected.

-

"If there is a regular or sustained occurrence " "of this message reseat the memory or replace " "the memory with memory that is known to " "be operational. "LOG_STD_RECUR_ACTION

PIMP-2-NOMEM

2-Critical

No memory available for [chars]

Process interrupt mask profiler subsystem could not obtain the memory it needed.

os

"Copy the message exactly as it appears and report it " "your technical support representative."

EXFREE-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified\n\ memory pool. The current system configuration network environment or\n\ possibly a software error might have exhausted or fragmented the\n\ router's memory.

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

EXFREE-2-EXMEMINIT

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be initialized.\n\ Reasons are not clear.

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

EXFREE-2-EXMEMRESET

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be reset.\n\ Reasons are not clear.

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

EXFREE-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent \n\ data some corruption.

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

EXFREE-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

EXFREE-2-EXMEMLOCK

2-Critical

[chars] detected error ptr [hec] size [dec].

Attempting to lock or unlock a memory location which was\n\ either already locked or unlocked.

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SEC_LOGIN-1-QUIET_MODE_ON

1-Alert

Still timeleft for watching failures is %lu secs [user: [chars]] [Source: [chars]] [localport: [dec]] [Reason: [chars]] [ACL: [chars]] at [chars]

Quiet Mode is ON. No request for connection is accepted other than allowed by the Access List if configured for the blocking period. Else an implicity *deny all* login's will be in force

os

"As all the requests from other sources are blocked check ACL and add" "any source addr. if needed."

SEC_LOGIN-5-QUIET_MODE_OFF

5-Notice

Quiet Mode is OFF because [chars] at [chars]

Quiet Mode is OFF. Router now operates in normal connection processing mode

os

"A notification that the device now operates in " "normal connection processing mode and the reason why it switched " "mode is also indicated with the notification."

SEC_LOGIN-4-LOGIN_FAILED

4-Warning

Login failed [user: [chars]] [Source: [chars]] [localport: [dec]] [Reason: [chars]] at [chars]

Invalid User Name or Password is given from terminal.

os

"A notification to indicate that login failed"

SEC_LOGIN-4-WEBUI_LOGIN_FAILED

4-Warning

Login failed [user: [chars]] [Source: [chars]] [Reason: [chars]] at [chars]

Invalid User Name or Password is given from terminal for WEBUI.

os

"A notification to indicate that WEBUI login failed"

SEC_LOGIN-5-LOGIN_SUCCESS

5-Notice

Login Success [user: [chars]] [Source: [chars]] [localport: [dec]] at [chars]

A successful login happened with the device.

os

"A notification that login succeeded."

SEC_LOGIN-3-INIT_FAILED

3-Error

Secure Login Initialization failed. [chars]

Initialization of Secure Login Subsystem failed

os

-

PQUICC-1-NOMEMORY

1-Alert

msgtxt_nomemory

The MPC860/PowerQUICC CPU was unable to access the memory it needs to\n\ carry out its functions. Here are some possible causes.\n\\n\ The network is large requiring a lot of memory for routing tables and\n\ so on.\n\\n\ The router configuration has many features enabled each of which\n\ require a certain amount of memory.\n\\n\ A software error memory leak exists.

-

"Reduce system activity to ease the memory demand or upgrade to a\n\ larger memory configuration."

PQUICC-3-OWNERR

3-Error

msgtxt_ownerror

An internal software error occurred.

-

"Call your technical support representative to obtain a software\n\ upgrade."

PQUICC-1-INITFAIL

1-Alert

PQUICC[dec]/[dec] SCC[dec] init failed

The software failed to initialize/restart a 1T serial card.

-

"Clear the serial interface.\n\ If the message recurs call your technical support representative for\n\ assistance."

PQUICC-1-CTSLOST

1-Alert

PQUICC[dec]/[dec] Clear to Send Lost

-

-

"Check the serial interface cable and/or communication equipment such\n\ as the channel service unit/data service unit CSU/DSU."

PQUICC-1-UNDERFLO

1-Alert

PQUICC[dec]/[dec] Transmit underflow

While transmitting a frame the serial controller chip's local buffer\n\ received insufficient data because data could not be transferred to the\n\ chip fast enough to keep pace with its output rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required."

PQUICC-1-LINEFLAP

1-Alert

PQUICC[dec]/[dec] Excessive modem control changes

-

-

"Check the serial interface cable. The error can occur if the cable is\n\ disconnected or has come loose and is picking up noise. If the cable\n\ appears to be connected correctly check the equipment connected to the\n\ cable."

PQUICC-1-BADHDXFSM

1-Alert

PQUICC[dec]/[dec] Unexpected HDX state [dec] event [dec]

A bad event was detected in the state machine for half duplex\n\ transmission/reception.

-

"Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC-1-TOOSMALL

1-Alert

PQUICC[dec]/[dec] packet was less than 2 bytes\n\msgdef_explanation A small packet

-

-

-

PQUICC-1-TOOBIG

1-Alert

PQUICC[dec]/[dec] packet too big packet size was [dec] bytes

A packet greater than the assigned MTU of this serial interface\n\ was queued up for transmission.

-

"The system should recover. No action is required.\n\ \n\ If the message recurs it may indicate an error\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC-1-UNKNOWN_WIC

1-Alert

PQUICC[dec] WIC card has an unknown ID of 0x[hec]

The software does not recognize the type of WIC card plugged\n\ into the port module.

-

"Check the part number on the WIC card to verify that it is supported\n\ in the IOS release operational on the router or contact\n\ your technical support representative."

PQUICC-1-WRONG_SLOT

1-Alert

PQUICC[dec] BRI card in wrong slot1

The BRI card is not supported in WIC slot 0.

-

"Power down move the BRI card to the other WIC slot on the\n\ port module and reboot."

PQUICC-3-UNKNOWN_SCCS

3-Error

PQUICC Incorrect SCC number

An internal software error occurred.

-

"Call your technical support representative to obtain a software\n\ upgrade."

PQUICC-1-UNSUPPORTED_CONFIG

1-Alert

Slot [dec] has an unsupported combination of ISDN WAN interface cards

It is not possible to support this type of BRI card in\n\ slot 1 along with another BRI card in slot 0.

-

"Remove one of the BRI cards from either slot."

PQUICC-1-UNEXPECTED_INTERRUPT

1-Alert

PQUICC[dec] Unexpected modem-signal interrupt

The software did not expect to see a modem control signal change\n\ on this type of WIC card interface.

-

"Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC-1-QMC_GLOBAL_ERROR

1-Alert

PQUICC[dec]/[dec] Global error [hec] in QMC

One or more of the channels served by the QMC instance encountered\n\ transmitter underflow or receiver overflow or the QMC interrupt\n\ table overflowed. Normally such a problem is temporary depending on \n\ transient peak loads within the system.

-

"The system should recover. No action is required."

PQUICC-3-UNKNOWN_SCC_TX_VECTOR

3-Error

PQUICC Unknown TX vector on port [dec]

An internal software error occurred.

-

"Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC-3-SPURIOUS_INTERRUPT

3-Error

Interface card in slot [dec] generated a spurious interrupt

Interface card on the router which is not supported by this image\n\ generated a spurious interrupt that can not be handled.

-

"No action is required. To avoid seeing this message in the future\n\ remove the unsupported card or use an image that supports it."

ALIGN-3-CORRECT

3-Error

Alignment correction made at 0x[hec] [chars]ing 0x[hec]

A software component within the router needs memory optimization.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-FULL

3-Error

Alignment log is full - no new entries will be recorded

The router identified more software components in need of memory\n\ optimization than it can record.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-SPURIOUS

3-Error

Spurious memory access made at 0x[hec] reading 0x[hec]

An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked.

-

"Copy the error message exactly as it appears on the console or in the " "system log. Issue the <CmdBold>show alignment<noCmdBold> command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the <CmdBold>show alignment<noCmdBold> output call your " "Cisco technical support representative and provide the representative " "with the gathered information."

ALIGN-3-TRACE

3-Error

-Traceback= %08x %08x %08x %08x %08x %08x %08x %08x

A trace that shows where the previous ALIGN error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ALIGN-3-TRACEX

3-Error

[chars]

A trace that shows where the previous ALIGN error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ISRHOG-4-MASK

4-Warning

Process masked interrupts for more than [dec] microsecs\nProcess-Block-Time [dec] microsecs

The process blocked interrupts for more than the latency threshold set\n\ for the ISRHOG tool.

Determine the component from the traceback displayed in\n\ the error message. Use Topic to search for a similar DDTS.\n\ If you find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical\n\ support representative."

ISRHOG-2-NOMEM

2-Critical

No memory available for configuring ISRHOG

The ISRHOG protocol subsystem could not obtain the memory it needed.

The leak may be generic or by any of the IOS processes consult the \n\ Technical Engineer. Use Topic to search for a similar DDTS.\n\ If you find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical\n\ support representative."

SYS-4-GD_DATAUNRELIABLE

4-Warning

Update to memory leak detector on free of 0x[hec] failed CLI output is unreliable\n

managed chunk malloc to store the range that is freed while memory leak detector is in progress failed. Hence memory leak detector will not be updated of this free and this can be reported as leak which is false.

mem

"Ignore the output of \"show memory debug leaks..\" if system is in low " "memory condition else perform a bug toolkit search on the web for " "existing bugs related to this error message if none found contact TAC " "for this problem providing \"show version\" and " "\"show memory statistics\" output."

SYS-4-RESBUFEXCEED

4-Warning

Resource user[chars] [chars] has exceeded the buffer [chars] threshold. configured [dec] Current usage :[dec]\n

The Resource User specified in the error message has violated the configured threshold. Its buffer usage has gone above the threshold. RESBUFEXCEED notifications should be matched with the corresponding RESBUFRECOVER/RESBUFUNAPPLY notification.

rmi

"No action is required"

SYS-5-RESBUFRECOVER

5-Notice

Resource user[chars] [chars] has recovered after exceeding the buffer [chars] threshold. configured [dec] Current usage :[dec]\n

The Resource User specified in the error message has recovered from the high buffer usage. Its usage has gone below the threshold

rmi

"No action is required"

SYS-5-RESBUFUNAPPLY

5-Notice

Buffer Usage of resource user[chars] [chars] is no longer monitored for the [chars] threshold.\n

The Resource User specified in the error message is no longer monitored for high buffer usage. The corresponding policy is revoked

rmi

"No action is required"

SYS-4-RESGLOBALBUFEXCEED

4-Warning

Buffer usage has gone above buffer [chars] threshold configured by resource user[chars] [chars]\n configured [dec] Current usage :[dec]\n

The global buffer usage has gone above the threshold of the RU specified in the error message. RESGLOBALBUFEXCEED notifications should be matched with the corresponding RESGLOBALBUFRECOVER/ RESGLOBALBUFUNAPPLY notification.

rmi

"No action is required"

SYS-4-RESGLOBALBUFRECOVER

4-Warning

Buffer usage has gone below buffer [chars] threshold configured by resource user[chars] [chars]\n configured [dec] Current usage :[dec]\n

The global buffer usage has gone below the threshold of the RU specified in the error message.

rmi

"No action is required"

SYS-4-RESGLOBALBUFUNAPPLY

4-Warning

Global Buffer usage for resource user[chars] [chars] is no longer monitored for [chars] threshold.\n

The global buffer usage configured by the Resource User specified in the error message is no longer monitored for the specified threshold. The corresponding policy is revoked

rmi

"No action is required"

SYS-4-GLOBALBUFEXCEED

4-Warning

Buffer usage has gone above global buffer [chars] threshold \nconfigured [dec] Current usage :[dec]\n

global buffer usage has gone above the configured limit. This violation can happen because of all the entities which use buffers in the system. GLOBALBUFEXCEED notifications should be matched with the corresponding GLOBALBUFRECOVER/GLOBALBUFUNAPPLY notification.

rmi

"No action is required"

SYS-5-GLOBALBUFRECOVER

5-Notice

Buffer usage has gone below global buffer [chars] threshold\nconfigured [dec] Current usage :[dec]\n

global buffer usage has gone below the configured limit. This is the indication of recovery

rmi

"No action is required"

SYS-5-GLOBALBUFUNAPPLY

5-Notice

Global Buffer usage is no longer monitored for [chars] threshold\n

Global buffer usage is no longer monitored for the specified threshold. The corresponding policy is revoked

rmi

"No action is required"

SYS-4-RESMEMEXCEED

4-Warning

Resource user [chars] has exceeded the [chars] memory threshold\nPool: [chars] Used: %lu Threshold: %lu \n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit. RESMEMEXCEED notifications should be matched with the corresponding RESMEMRECOVER/RESMEMUNAPPLY notification.

rmi

"No action is required"

SYS-5-RESMEMRECOVER

5-Notice

Resource user [chars] has recovered after exceeding the [chars] memory threshold\nPool: [chars] Used: [dec] Threshold :[dec] \n

The memory pool specified in the error message is recovering from a low-memory condition. The amount of free memory available in the specified memory pool has recovered above the configured low-memory limit.

rmi

"No action is required"

SYS-5-FREEMEMLOW_NOTIFY

5-Notice

Top memory allocators could not be displayed currently at low memory situation refer show memory output/crashinfo file.

IOSD memory consumption exceeded 90% Top memory allocator could not be displayed. Top allocators can be found from show memory output or crashinfo file.

mem

"No action is required"

SYS-5-RESMEMUNAPPLY

5-Notice

Memory usage of Resource user [chars] is no longer monitored for [chars] threshold. Pool: [chars]\n

The memory pool specified in the error message is no longer monitored for low-memory condition as configured by the Resource User specified. The corresponding policy is revoked.

rmi

"No action is required"

SYS-3-GD_STACKERR

3-Error

Unknown stack. Process: [chars]\n

An internal error occurred when running the memory leak detector

mem

"Copy the error message exactly as it appears on the console or in the" " system log and look up the message in the Bug Toolkit at:" " http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you are" " unable to resolve the issue using Bug Toolkit please issue a" " \"show tech\" and contact your technical support representative" " with the gathered information."

SYS-4-THRESHOLD

4-Warning

Free Memory has dropped below low watermark. Pool: [chars] Free: %lu Threshold: %lu

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-4-THRESHOLD_TK

4-Warning

Free Memory has dropped below low watermark. Pool: [chars] Free: %lu Threshold: %lu Tracekey: [chars]

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-4-FREEMEMLOW

4-Warning

Top Allocator Name: [chars] PC: [chars] Size: [dec] Count: [dec] Largest block: %-9lu

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-5-FREEMEMRECOVER

5-Notice

Free Memory has recovered above low watermark Pool: [chars] Free: %lu freemem_lwm: %lu

The memory pool specified in error message has recovered from a low-memory condition and free memory in that pool is now above the configured low-memory limit in the system .

-

"No action is required"

SYS-5-GLOBALMEMEXCEED

5-Notice

Global Memory has exceeded the [chars] threshold\nPool: [chars] Used: %lu Threshold: %lu\n

The memory pool specified in the error message has exceeded the global memory threshold configured.the memory consumed in that pool has exceeded the configured limit. GLOBALMEMEXCEED notificatons should be matched with the corresponding GLOBALMEMRECOVER/GLOBALMEMUNAPPLY notification.

rmi

"No action is required"

SYS-5-GLOBALMEMRECOVER

5-Notice

Global Memory has recovered after exceeding [chars] threshold\n Pool: [chars] Used: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the memory consumed in that pool is now below the configured limit.

rmi

"No action is required"

SYS-5-GLOBALMEMUNAPPLY

5-Notice

Global Memory usage is no longer monitored for [chars] threshold. Pool: [chars]\n

The memory pool specified in the error message is no longer monitored for low-memory condition. The corresponding policy is revoked

rmi

"No action is required"

SYS-4-RESGLOBALMEMEXCEED

4-Warning

Global Memory has exceeded the [chars] threshold configure by resource user [chars]\n Pool: [chars] Used: %lu Threshold: %lu\n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit. RESGLOBALMEMEXCEED notifications should be matched with the corresponding RESGLOBALMEMRECOVER/RESGLOBALMEMUNAPPLY notification.

rmi

"No action is required"

SYS-4-RESGLOBALMEMRECOVER

4-Warning

Global Memory has recovered after exceeding the [chars] threshold configure by resource user [chars]\n Pool: [chars] Used: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the free memory in that pool is now above the configured low-memory limit.

rmi

"No action is required"

SYS-4-RESGLOBALMEMUNAPPLY

4-Warning

Global Memory Usage for resource user [chars] is no longer monitored for [chars] threshold. Pool: [chars]\n

The memory pool specified in the error message configured by the specified Resource User is no longer monitored for low-memory condition. The corresponding policy is revoked

rmi

"No action is required"

SYS-2-MALLOCFAIL

2-Critical

Memory allocation of [dec] bytes failed from [hex] alignment [dec] \n Pool: [chars] Free: [dec] Cause: [chars] \nAlternate Pool: [chars] Free: [dec] Cause: [chars] \n

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error may have exhausted or fragmented the router's memory.

mem-suspect

"If you suspect a software error copy the error message exactly as it " "appears on the console or in the system log contact your technical support" "representativeand provide the representative with the gathered information. " "Otherwise you may need to add more memory or reduce the number of " "features you are trying to support."

SYS-2-MUTEXLOCKFAIL

2-Critical

pthread_mutex_lock failed for [chars]

The thread failed in pthread_mutex_lock while trying to acquire a mutex.

mem-suspect

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-NOMEMORY

2-Critical

No memory available for [chars] [dec]

An operation could not be accomplished because of a low-memory condition. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

mem-suspect

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a configuration that has more memory."

SYS-3-CRITMEM

3-Error

[chars]

An attempt to allow or disallow a process from using memory that has been reserved for critical purposes has failed. The location of the failure is specified in the error message. This condition could possibly be caused by a software error.

mem-suspect

"Copy the error message and the traceback messages exactly as they appear " "on the console or in the system log contact your technical support " "representative and provide the representative with the gathered " "information."

SYS-2-GETBUFFFAIL

2-Critical

[chars] buffer allocation [dec] bytes failed from [hex]

-

-

-

SYS-6-NOBRIDGE

6-Information

Bridging software not present

Your system is not configured to be a bridge.

none

"Configure the bridging software."

SYS-3-SOCKUNKN

3-Error

Unknown socket protocol [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-HARIKARI

3-Error

Process [chars] top-level routine exited

An internal software error occurred

Determine the component from the process name displayed in the error message.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPID

2-Critical

Bad pid [dec] for tty [t-line]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-MGDTMRRUN

3-Error

TTY[t-line]: Managed Timers [chars] still running

One or more managed timers for a TTY that is deleted are still running.

-

LOG_STD_ACTION

SYS-0-USERLOG_EMERG

0-Emergency

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-1-USERLOG_ALERT

1-Alert

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-2-USERLOG_CRIT

2-Critical

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only. "

SYS-3-USERLOG_ERR

3-Error

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-4-USERLOG_WARNING

4-Warning

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-5-USERLOG_NOTICE

5-Notice

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-6-USERLOG_INFO

6-Information

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-7-USERLOG_DEBUG

7-Debug

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-3-MSGLOST

3-Error

[dec] messages lost because of queue overflow

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-REGEXP

4-Warning

[chars].

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-5-RESTART

5-Notice

System restarted --\n[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SCHEDULED_RELOAD

5-Notice

Reload requested for [chars]

A scheduled reload has been requested for the router.

none

"No action is required."

SYS-5-SCHEDULED_RELOAD_CANCELLED

5-Notice

Scheduled reload cancelled at [chars]

A scheduled reload that was requested for the router has been cancelled.

none

"No action is required."

SYS-5-RELOAD

5-Notice

Reload requested[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SWITCHOVER

5-Notice

Switchover requested[chars]

A switchover was requested.

none

"This is a notification message only. No action is required."

SYS-4-RELOAD_ATTEMPT

4-Warning

Attempt via SNMP failed system shutdown not configured

SNMP cannot be used to reload the router unless this functionality has been previously configured. This message reports that an attempt to reload the router failed because SNMP reloads are not currently configured on the router.

none

"This is a notification message only. No action is required."

SYS-3-CFG_AT_RELOAD

3-Error

System reloading unable to complete startup configuration update

Startup configuration updation is already in progress and reload has been called either from interrupt level or with all interrupts disabled. Reload can not suspend to let startup configuration updation get completed. Startup configuration may get corrupted.

none

"This is a notification message only. No action is required."

SYS-4-DUAL_MESSAGE

4-Warning

SNMP system message request [dec] denied because of pending job

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-LOGOUT

6-Information

User [chars] has exited tty session [dec][chars]

A user has closed a tty session normally using the exit CLI command.

os

"This message is for information only. " "No action is required."

SYS-5-CONFIG

5-Notice

Configured from [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_R

5-Notice

Config Replace is [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_C

5-Notice

Running-config file is [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_P

5-Notice

Configured programmatically by process [chars] from [chars] as [chars]

The router's configuration was changed programmatically.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_I

5-Notice

Configured from [chars] by [chars]

The write of the system running configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_RESOLVE_FAILURE

4-Warning

System config parse from [chars] failed

The configuration file from the URL specified in the error message could not be read.

-

"Enter the <CmdBold>no service config<NoCmdBold> " "command to disable autoloading of configuration files " "OR investigate why the tftp load is failing."

SYS-5-CONFIG_NV

5-Notice

Nonvolatile storage configured from [chars]

The configuration was written successfully.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_NV_I

5-Notice

Nonvolatile storage configured from [chars] by [chars]

The write of the nonvolatile configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-CONFIG_NV_DATA

3-Error

Variable [chars] not set properly in the routine [chars].

The write of the nonvolatile configuration failed because an internal variable was not set properly.

-

"If this messages occurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_NEWER

4-Warning

Configuration from version [dec].[dec] may not be correctly understood

The software detected that the configuration saved in memory was written by a newer version of software. There might be commands saved in memory that are not implemented by the older software version.

none

"Examine all the messages printed while the router was " "booting. For each message about an unknown command determine " "whether that feature is required. If so upgrade to a " "newer version of software that supports that feature."

SYS-4-CONFIG_NOLOCK

4-Warning

The configuration could not be locked

A software error occurred.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SYS-3-CONFIG_NO_PRIVATE

3-Error

No space remaining to save private config

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-CONFIG_NV_OVERRUN

4-Warning

Non config data present at the end of nvram is corrupted

The software detected that the configuration saved into nvram has overlaid a part of the nvram occupied by non config data files.Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configuration and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_TRUNCATE

4-Warning

Truncated configuration to %ld bytes from %ld bytes

The software detected that the configuration saved into nvram has been truncated. There was not enough space to save the compressed configuration.

-

"Save the configuration to flash if the platform supports " " \"boot config\" command."

SYS-4-CONFIG_NV_NEED_OVERRUN

4-Warning

Non config data present at the end of nvram needs to be overwritten to fit the configuration into nvram

The software detected that the non config data files occupying the end of nvram need to be overwritten to fit the configuration. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configuration and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_NEED_TRUNCATE

4-Warning

Configuration needs to be truncated to fit into nvram

The software detected that the configuration is to be truncated to fit in the nvram. There was not enough space to save the compressed configuration

-

"Save the configuration to flash if the platform supports " "\"boot config nvbypass\" command."

SYS-4-NV_BLOCK_INITFAIL

4-Warning

Unable to initialize the geometry of nvram

The software detected that it failed to initialize the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload. This may happen when the entire nvram is packed with the configuration and the newer version of software which supports this feature could not find the minimum room in the nvram to initialize block file system.

-

"Reduce the configurations in the nvram atleast by 2K"

SYS-7-NV_BLOCK_INIT

7-Debug

Initialized the geometry of nvram

Initialized the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

""

SYS-4-NV_CHKSUM

4-Warning

An nvram checksum is already in progress

An interrupt service routine attempted to perform a checksum on the nvram contents and found the resource in use.

nvram

-

SYS-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-NV_NOLOCK

4-Warning

Failed to acquire an nvram lock

An interrupt service routine's attempt to acquire a semaphore lock failed

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent data some corruption.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-PRIVCFG_ENCRYPT_SUCCESS

6-Information

[chars]

Private config encryption successful

none

"This is an informational message."

SYS-2-PRIVCFG_ENCRYPT_FAILURE

2-Critical

[chars]

An error was encountered by the private config encryption

none

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-PRIVCFG_DECRYPT_SUCCESS

6-Information

[chars]

Private config decryption successful

none

"This is an informational message."

SYS-2-PRIVCFG_DECRYPT_FAILURE

2-Critical

[chars]

An error was encountered by the private config decryption

none

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CONFIG_DOWNFAIL

2-Critical

Generated configuration not backward compatible

The router has been configured to generate nonvolatile memory using the commands of an older software version. The current configuration of the router contains a command that cannot be saved using only the older command set.

none

"Allow the router to save the configuration using the command set of " "the current software version or remove the commands that cannot be " "saved using the older command set."

SYS-5-OUTSETUP

5-Notice

Configuration file [chars] accepted aborting setup

A configuration was accepted over the network so the setup session will be aborted.

none

"This is a notification message only. No action is required."

SYS-3-BADLINKTYPE

3-Error

* Unexpected linktype [dec]

* A software error occurred.

udp

* "Copy the error message exactly as it appears and report it to your " * "technical support representative."

SYS-2-SIGNUM

2-Critical

Process aborted on invalid signal signum = [dec].

An attempt was made to send an invalid signal to another process.

-

"If this message occurs more than once report this message " "to your technical support representative."

SYS-3-CPUHOG

3-Error

Task is running for [dec]msecs more than [dec]msecs [dec]/[dec]

The indicated process ran too long without relinquishing the processor. Each process should run for a small amount of time and then relinquish the CPU so that other processes can run. This problem can be caused by many things like traffic or system load hardware or operational configuration a configuration change initialization of many interfaces cards or ports for example a high momentary error rate a sustained abnormal

If this error occurs in conjunction with a TIMERHOG message \n\ report the two errors together and use the component obtained \n\ for the TIMERHOG message.

"If you suspect a software error copy the error message exactly as it " "appears on the console or in the system log contact your technical support" "representative and provide the representative with the gathered information."

SYS-2-WATCHDOG

2-Critical

Process aborted on watchdog timeout process = [chars].[chars]

The indicated process ran for too long without relinquishing control. The system killed it as a runaway process.

-

-

SYS-3-TIMERHOG

3-Error

Timer callback ran long PC = [hec].

The indicated callback routine ran for too long without relinquishing the processor.

Determine the component from the callback routine address displayed in\n\ the error message. Use Topic to search for a similar DDTS. If you \n\ find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-6-STACKLOW

6-Information

Stack for [chars] [chars] running low [dec]/[dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-GREEDY_REGEXP

4-Warning

[chars] while processing the input regular expression. Aborting processing use alternate regular expression. Input regular expression: \[chars]\

Regular expression processing limitation: Certain regular expressions require huge stack space for processing or can lead to processing timeouts. We abort processing such regular expressions and print this message to avoid stack overflow/unexpected reload.

os

"The regular expression specified leads to stack overflow/processing " "timeout of the indicated process. Recommended to use a different " "regular expression."

SYS-1-CPURISINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr: [dec]%%/[dec]%%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped.

-

"Enter the <CmdBold>show processes CPU<NoCmdBold>" " command to determine the CPU hogging process" " that is causing this condition and if possible" " disable the activity that is causing the" " CPU hog condition so that CPU" " utilization is reduced."

SYS-1-CPUFALLINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr [dec]%%/[dec]%%.

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required."

SYS-2-INPUTQ

2-Critical

INPUTQ set but no IDB ptr=[hec]

This message is issued when an attempt is made to alter the input queue count for a packet that should not be counted.

-

-

SYS-6-BADSHAREINFO

6-Information

[chars] packet [hec] has a zero reference count freeing pid = [hec] \n\ freeing pc = [hec] [chars].

Provides additional information about original freer of packet.

-

-

SYS-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[hec]

A reference count is used to track the usage of many data structures. A function increments the count when it begins to use a structure and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be negative which means that the data structure will not be freed until the system is reloaded.

-

-

SYS-4-ADD_STACK

4-Warning

Invalid index [dec] for additional stack size request.

The index passed should of less than the enum E_MAX_ADD_STACK_SIZE value equal to or higher than the enum is an invalid index.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKLEV

2-Critical

Process creation of [chars] failed at level [dec].

An internal software error occurred.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKMEM

2-Critical

Process creation of [chars] failed no memory.

Insufficient memory was available to create a process either while trying to support additional features or due to a memory leak.

mem-suspect

"A memory leak may be the cause if the system has been running for a " "while without changing its configuration. If you suspect a leak then " "copy this message exactly as it appears and report it to your technical " "support representative. Otherwise ensure that more memory is available " "to support the additional features."

SYS-2-CFORKBADFUNCT

2-Critical

Can't create process with start address = [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPROCESS

3-Error

Bad process ID [dec] when [chars] process table

An internal software error occurred.

os-scheduler

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INSCHED

2-Critical

[chars] within scheduler

-

Determine the component from the stack trace displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem.

-

SYS-2-NOTIOSTASK

2-Critical

[chars] from outside IOS task context

An IOS reschedule request was made from code that is not running in the context of an IOS task -- from an interrupt handler the scheduler itself or a service pthread within the IOS process.

Determine the component from the stack trace displayed in the\n\ error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-SEMSCHED

2-Critical

'[chars]'

The scheduler was entered with mempool semaphore held.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called with mempool semaphore held choose the DDTS component based on the process name displayed.

-

SYS-2-INTSCHED

2-Critical

'[chars]' at level [dec] [chars]

The scheduler was entered from an interrupt service routine ISR.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

-

SYS-3-PROCSEMFAIL

3-Error

Process semaphore creation for preemptive processes failed.

Creation of process function semaphore to protect the critical section of process create routine failed. The semaphore creation can fail if there isnt enough chunk memory to create the event structure.

os

-

SYS-2-NOBLOCK

2-Critical

[chars] with blocking disabled.

A process attempted to relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

-

SYS-2-BLOCKHUNG

2-Critical

Task hung with blocking disabled value = 0x[hec].

The indicated process has exceeded the time limit for which it may relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

"This message may be a result of high loads. If it recurs " "copy the text exactly as it appears and report it along " "with the associated stack trace to your technical support " "representative."

SYS-2-NOTDEAD

2-Critical

Killing process [chars] pid [dec] again

An internal software error occurred.

os-scheduler

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOPROCESS

2-Critical

No such process [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-IMMORTAL

2-Critical

Attempt to shut down management process [dec] [chars].

An attempt was made to shut down the specified management\n\ process. Management processes must not be shut down as long as the\n\ router remains up.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the process_kill.

-

SYS-2-SIGPENDING

2-Critical

Multiple Signals are sent to a process [dec]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADSTACK

2-Critical

Process [chars] has trashed stack old size [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-6-MTRACE

6-Information

[chars]: addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC

This is an auxiliary message to several memory-related messages. It provides the address of the memory block and the calling program counter for the last eight blocks allocated and for the last eight blocks freed.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of a previously printed error message."

SYS-6-BLKINFO

6-Information

[chars]blk [hec] words [dec] alloc [hec] [chars] dealloc [hec] rfcnt [hec]

This is an auxiliary message to several memory-related messages. It provides a formatted display of some of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-MEMDUMP

6-Information

[hex]: [hex] [hex] [hex] [hex]

This is an auxiliary message to several memory-related messages. It provides a raw display of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-PROCINFO

6-Information

Process [chars] just finished executing

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

-

"Copy this messages exactly as it appears and report it along with " "the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your " "technical support representative."

SYS-6-TESTINFO

6-Information

Scheduler test [hex] for [chars] just executed

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

Determine the component from the address of the scheduler test routine\n\ displayed in the error message.\n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy this message exactly as it appears and report it along with the " "SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical " "support representative."

SYS-3-BADBLOCK

3-Error

Bad block pointer [hec]

A block of memory at the indicated location is corrupt. An internal check of memory block pointers indicates an inconsistency.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload then the router will " "need to reloaded manually."

SYS-3-BADMAGIC

3-Error

Corrupt block at [hec] magic %08x

The free memory pool is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADREFCOUNT

3-Error

Bad reference count at [hec] refcount [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-3-OVERRUN

3-Error

Block overrun at [hec] red zone %08x

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-FREEBAD

2-Critical

Attempted to free memory at [hec] not part of buffer pool

An attempt was made to free memory but the request could not be completed due to an invalid memory data structure

-

-

SYS-2-MADVISEFAIL

2-Critical

Madvise failed memory at [hec].

An attempt was made to create secure mempool but it failed.

os

"This is a notification message only. No action is required."

SYS-2-FREEFREE

2-Critical

Attempted to free unassigned memory at %lx alloc %lx dealloc %lx

An attempt was made to free memory at the indicated location. The memory could not be freed because it was not allocated.

-

-

SYS-3-INVMEMINT

3-Error

Invalid memory action [chars] at interrupt level

This message indicates that a memory allocation or deallocation was attempted from an interrupt handler.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-INVMEMPID

3-Error

Invalid pid [dec] in block: [hec]

There has been attempt to allocate memory on behalf of an invalid process.

mem

-

SYS-3-MEMSEMFAIL

3-Error

Mempool semaphore creation failed for [chars]

This message indicates that the semaphore creation for the specified mempool failed.

-

-

SYS-3-INUSEFREE

3-Error

Block [hec] on free list [dec] in use

A memory management function attempted to allocate the indicated block from a list of free blocks. However the block was found to be already in use.

-

-

SYS-3-NZREFCNT

3-Error

Block [hec] on free list [dec] with refcount [dec]

A block of memory in the free pool is actually in use. The message indicates the number of processes using the memory block.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-WRONGFREELIST

3-Error

Block [hec] size [dec] on wrong free list [dec] [dec]

A freed buffer was placed on the wrong list of free buffers.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEMAGIC

3-Error

Corrupt free block at [hec] magic %08x

A block of memory at the indicated location is corrupt. An inconsistency was detected while checking the free memory area.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADPTRVAL

3-Error

Bad pointer value [chars] = [hec] in function [chars]

Corrupted pointer value is encountered.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEPTRS

3-Error

Bad [chars] pointer [hec] at [hec] [chars] = [hec]

A pointer in the block header at the indicated location is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-GETBUF

2-Critical

Bad getbuffer bytes= [dec]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

-

SYS-2-INPUT_GETBUF

2-Critical

Bad getbuffer bytes= [dec] for interface= [chars]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

LOG_STD_ACTION

SYS-2-INLIST

2-Critical

Buffer in list ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-INLIST1

2-Critical

Buffer in list ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED1

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPOOL

2-Critical

Attempt to use buffer with corrupt pool pointer ptr= [hec] pool= [hec]

An memory management function attempted an operation that could not be performed due to invalid memory pool descriptors.

-

-

SYS-2-BADPOOLMAGIC

2-Critical

Attempt to use pool pointer with corrupt header pool= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-WRONGPOOL

2-Critical

Buffer [hec] found in pool [hec] should be in pool [hec]

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-2-BADBUFFER

2-Critical

Attempt to use [chars] buffer as [chars] ptr= [hec] pool= [hec]

A hardware or software error occurred. An inconsistency was encountered while processing a packet buffer.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information."

SYS-2-QCOUNT

2-Critical

Bad [chars] [hec] count [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOTQ

2-Critical

[chars] didn't find [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-LINKED

2-Critical

Bad [chars] of [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SELFLINKED

2-Critical

Buffer [hec] linked to itself in free pool [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-ALREADYFREE

2-Critical

Buffer [hec] already in free pool [chars]

A block of memory at the indicated location is corrupt and/or has been erroneously freed twice.

os

"If this message recurs copy it exactly as it appears and the output " "of 'show buffer address <number>' for the given address as well as " "'show buffer pool <name> dump' for the given pool. Report it to your " "technical support representative."

SYS-2-LOWMEMPROC

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available processor memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak copy the message exactly as it appears and " "report it to your technical support representative. Otherwise you may " "need to add memory or reduce the number of features you are trying to " "support."

SYS-2-LOWMEMIO

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available IO memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak " "copy the message exactly as it appears and " "report it to your technical support representative. " "Otherwise you may need to add memory " "or reduce the number of features you are trying to " "support."

SYS-2-NOMEMFRGPROC

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous processor memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-NOMEMFRGIO

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous IO memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing " "copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-SPEC

2-Critical

Trying to set unknown special character [dec] to [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-ABRUPTTERM

3-Error

Abrupt termination of tty session for [chars] [t-line]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADDISP

3-Error

Bad disposal code [hec] in [chars]

An invalid status code has been passed to a buffer deletion routine. The buffer will be correctly returned to the free pool but will not be correctly counted in the per-protocol statistics.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NULLIDB

3-Error

Null IDB in [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-1-OVERTEMP

1-Alert

System detected OVERTEMPERATURE condition.\n Please resolve cooling problem immediately!\n

The environmental monitor detected a high-temperature condition.

none

"Make sure that the room temperature is not too high and that air flow " "to the card is not blocked. If this condition persists the " "environmental monitor might shut down the system. Call your technical " "support representative for assistance if necessary."

SYS-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADRESID

3-Error

Clock hardware returned bad residual [dec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPRINT

3-Error

Process has no associated tty in [chars].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-INTPRINT

3-Error

Illegal printing attempt from interrupt level.

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-OVFPRINT

3-Error

Overflow in [chars] chars [dec] buffer size [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NOELEMENT

3-Error

[chars]:Ran out of buffer elements for enqueue

The process was unable to enqueue data as it ran out of buffer elements.

-

"Copy the error message exactly as it appears also get the " "output of show buffers and report it to your technical support " "representative."

SYS-4-PUPDATECLOCK

4-Warning

Periodic Clock update with ROMMON failed because size left in ROMMON %lu size needed %lu error code %ld

This message indicates that the periodic update of the clock to ROMMON failed. This would indicate that the router when restarted may have past clock values

os

"Drop to rommon and clear unwanted rommon variable entries"

SYS-6-CLOCKUPDATE

6-Information

System clock has been updated from [chars] to [chars] configured from [chars] by [chars].

This message indicates that the system clock has been modified.

-

"This is informational message."

SYS-3-TIMEZONE_INVALID

3-Error

Invalid timezone name

The timezone string entered is not valid. The string\n\ should be minimum of more than three letters and should\n\ only contain alphabets

os

-

SYS-5-TABLEERR

5-Notice

[chars] table [chars] damaged: [chars].

An internal table entry became corrupt.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-3-BADTREEPARAM

3-Error

Bad parameter for [chars] passed to tree library function.

This message indicates that a pointer passed to a tree library function is invalid.

-

LOG_STD_SH_TECH_ACTION

SYS-2-BADLIST

2-Critical

Regular expression access check with bad list [dec]

This message indicates that a pointer to an access list is invalid.

-

"The event that caused this message to be issued should not " "have occured. It can mean that one or more data structures " "have been overwritten. If this message recurs and you decide " "to report it to your technical representative you should " "copy the text of the message exactly as it appears and " "include the associated stack trace." "\n\n Since access list corruption may have occurred " "a technical representative should verify that access " "lists are functioning corectly."

SYS-2-SNMP0IDX

2-Critical

Attempt to [chars] snmpidb with if_index of 0

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-SNMP_WRITENET

4-Warning

SNMP WriteNet request. Writing current configuration to [inet]

SNMP is writing the current configuration to a network host.

none

"These are notification messages only. No action is required."

SYS-4-SNMP_HOSTCONFIGSET

4-Warning

SNMP hostConfigSet request. Loading configuration from [inet]

SNMP is reading the host configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-SNMP_NETCONFIGSET

4-Warning

SNMP netConfigSet request. Loading configuration from [inet].

SNMP is reading the network configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-INVALID_IMAGE

4-Warning

Running invalid image for platform!

The software image being run is for a different hardware architecture. This problem can occur on a Cisco 1003 Cisco 1004 or Cisco 1005. The Cisco 1003 and Cisco 1004 use a different image from the Cisco 1005.

none

"Install the correct software image."

SYS-2-CHUNKBOUNDS

2-Critical

Could not find the sibling to allocate memory from. Chunk [chars] total free [dec] inuse [dec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBOUNDSIB

2-Critical

Error noticed in the sibling of the chunk 0x[hec] head_chunk 0x[hec] chunk name [chars] data 0x[hec] Chunk index : [dec] Chunk real max : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKDELAYSIB

2-Critical

Error noticed in freeing up of delayed siblings for chunk [chars] 0x[hec]. Delayed sibling free queue size : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SYS-2-CHUNKINVALIDOPR

2-Critical

[chars] Chunk : %lx Chunk Name : [chars] Flags : %lu

An operation intended for a type of chunk is used for a different type of chunk.

-

-

SYS-2-CHUNKDOUBLEFREE

2-Critical

Attempt to free a free chunk element. Chunk : %lx Head Chunk : %lx Chunk Name : [chars] Data : %lx Alloc : %lx Dealloc : %lx

An attempt was made to free a chunk element which is already free.

-

-

SYS-2-CHUNKFREE

2-Critical

Attempted to free nonchunk memory chunk [hec] data [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBADROOTCHUNKPTR

2-Critical

Bad root chunk pointer in chunk header chunk 0x[hec] data 0x[hec] root chunk ptr 0x[hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console or in " "the system log contact your Cisco technical support representative " "and provide the representative with the gathered information along " "with the ouput of the <CmdBold>show running-config<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands. " "Save any crashinfo or crashdump files. " "If the router has crashed and was not configured to reload " "automatically the router will need to be reloaded manually."

SYS-2-CHUNKSIBLINGDEST

2-Critical

Attempted to destroy a sibling chunk [hec] [chars].

-

-

-

SYS-2-CHUNKSIBLINGS

2-Critical

Attempted to destroy chunk with siblings chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKPARTIAL

2-Critical

Attempted to destroy partially full chunk chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKBADMAGIC

2-Critical

Bad magic number in chunk header chunk [hec] data [hec] chunkmagic [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-6-INVALID_BOOTTIME

6-Information

Time since last reboot not available

This is an informational message for the user. The time taken for the router to come up after OIR is not available.

-

"No action required."

SYS-6-LAST_RELOAD_BY_MEM_PRESSURE_CPU

6-Information

Last reload was triggered because CPU Usage due to Memory Pressure exceeds threshold

This is an informational message for the user to indicate the reason behind the last reload which was triggered by forcefully crashing top N memory intensive processes because system encountered low-memory pressure. By looking at the core-files developer may be able to narrow down the cause of the memory depletion.

-

"This is a notification message only. No action is required."

SYS-6-BOOTTIME

6-Information

Time taken to reboot after reload = %-4d seconds

This is an informational message for the user. This provides the time taken for the router to come up after reload or crash. The time is actually the difference between the last crash and a successive boot. If autoboot was not set and router is in rommon for a long time then the reload time shown could be large.

-

"No action required."

SYS-2-CHUNKBADREFCOUNT

2-Critical

Bad chunk reference count chunk [hec] data [hec] refcount [hec] alloc pc [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOMEMORY

2-Critical

* Could not allocate chunks for [chars]. No memory

* A software error occurred.

-

* "Copy the error message exactly as it appears and report it to " * "your technical support representative."

SYS-2-CHUNKEXPANDFAIL

2-Critical

Could not expand chunk pool for [chars]. No memory available

There is not enough processor memory left to grow this chunk pool.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADFREEMAGIC

2-Critical

Bad free magic number in chunk header chunk [hec] data [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOROOT

2-Critical

Root chunk need to be specified for [hec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINVALIDHDR

2-Critical

Invalid chunk header type [dec] for chunk [hec] data [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-CRASHINFOINITFAIL

3-Error

Crashinfo subsys initialization did not add registry \n\ crashinfo_get_default_file_name.\n

In order to figure out the device which the crashinfo writes to the crashinfo subsys has to add the registry crashinfo_get_default_file_name.

-

"Use Topic to search for a similar DDTS. If you find none write " "a DDTS for this problem. This SHOULD never happen - it is an " "indication of a bug elsewhere in the code."

SYS-2-CHUNKBADPOOLSIZE

2-Critical

Bad poolsize returned by the system : [dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-BADALIGNMENT

2-Critical

Bad alignment : [dec]

System requests a alignment which is not a power of 2

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINCONSIS

2-Critical

Inconsistant counters for chunk : [chars] total free [dec]/[dec] total sibs [dec]/[dec] total alloc [dec]/[dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADELESIZE

2-Critical

Chunk element size is zero or more than 64k for [chars]size : %lu

Chunk manager cannot function properly with big chunk elements

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNK_PP_CREATEDESTROY

4-Warning

A chunk is created or destroyed from pseudo-preemption context. Chunk name : [chars]

Creating or destroying chunks from pseudo-preemption context is not allowed.

-

"Copy the error message exactly as it appears and " "report it to your technical support representative."

SYS-2-NULLCHUNK

2-Critical

[chars] operation on Null Chunk

Chunk manager cannot allocate memory from NULL chunks

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNKSIBLINGSEXCEED

4-Warning

Number of siblings in a chunk has gone above the threshold. Threshold:[dec] Sibling-Count:[dec] Chunk:0x[hec] Name:[chars]

Number of siblings in a chunk with no header has gone above the default/configured threshold configured using <cmdBold>memory chunk siblings threshold<nocmdBold> <cmdArgs>count<nocmdArgs>

-

LOG_STD_SH_TECH_ACTION

SYS-2-CHUNK_FAST

2-Critical

Chunk infra detected a system error. Error Type:[chars] Chunk:%p Flags:0x[hec] Name:[chars]

An internel error has occured in chunk infra which forced a system crash. Contact cisco TAC with the exact error message and 'show tech-support' output.

mem

LOG_STD_SH_TECH_ACTION

SYS-1-CCA_SYS_ERR

1-Alert

CCA Detected System Error code = [dec]

CCA has detected a severe system software error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-2-CCA_INT_ERR

2-Critical

CCA Detected Logic Error code = [dec]

CCA has detected a severe internal logic error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-1-IPAM_INIT_FAIL

1-Alert

IPAM Initialization Failure code = [dec]

IPAM has detected an initialization failure. This condition is\n\ usually caused by a software error during IPAM initialization.

ipam

LOG_STD_ACTION

SYS-2-NV_BAD_PTR

2-Critical

Bad NVRAM pointer. NV Header values are nv: 0x%p .textbase: 0x%p .textsize: [dec] .magic: 0x%X .checksum: 0x%X .system_version: [dec] .textptr: 0x%p v1_ptr: 0x%p .priv: 0x%p

-

nvram

LOG_STD_SH_TECH_ACTION

SYS-4-NV_INVALID_BOOTUP

4-Warning

Nvram is invalid. Attempting to read and apply '[chars]' anyway

Nvram is corrupted. But still try to read startup-config as this was the behavior in 12.3T for platforms like c1700.

nvram

"Verify whether the box was powercycled or crash " "was triggered prior to this message. Issue 'show tech' command"

SYS-3-TIMERNEG

3-Error

Cannot start timer [hex] with negative offset [dec].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-MGDTIMER

3-Error

[chars][chars] timer = [hec].

This message indicates an error in a system timer. The problem can be caused either by software or by hardware.

-

-

SYS-3-DMPMEM

3-Error

%08x: %08x %08x %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-BOOT_MESSAGES

6-Information

Messages above this line are from the boot loader.\n

At least one informational or error message was printed by the boot loader.

-

"If the system image was loaded no action is recommended. If the " "system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-2-EXCEPTIONDUMP

2-Critical

System Crashed Writing Core....

The system has crashed because of an exception A core is being generated

-

LOG_STD_ACTION

SYS-3-LOGGER_FLUSHING

3-Error

System pausing to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system is paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_FLUSHED

3-Error

System was paused for %TE to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system was paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_DROPPED

3-Error

System dropped [dec] console debug messages.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

SYS-3-LOGGER_COUNT_STOP_CHUNK

3-Error

System cannot release chunk memory.\n

The system was not able to destroy a previously allocated chunk of memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-CHUNK_NO_EXMEM

3-Error

No handler to [chars] external memory.

An attempt was made to allocate or free a chunk of external memory but no handler for managing external memory was registered.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-READ_BOOTFILE_FAIL

6-Information

[chars] [chars].\n

A configured boot system command failed.

-

"If a system image was eventually loaded no action is recommended. If " "the system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-3-URLWRITEFAIL

3-Error

redirection url write failed '[chars]'

Redirection of output to URL failed.

-

"Check for free space on destination URL and retry."

SYS-6-READ_BOOTFILE_SKIP

6-Information

boot system [chars] command is skipped\n

A configured boot system command is skipped. Either the system experienced a crash while loading this image in the last attempt or the filename is not properly specified. Subsequent boot system commands will be tried

-

"Replace the failed boot system image with a good one. There could be " "various reasons that this specified image failed for example the image " "might be with a bad checksum."

SYS-6-USING_RESERVE_MEMORY

6-Information

Reserve memory is being used

The reserved memory is being used by the console

-

"The system is low in memory. The reserved memory will be " "used only by the console process. Please take a techsupport " "so that the reason for low memory can be found"

SYS-6-RESERVE_MEMORY_CREATED

6-Information

Reserve memory is being created

A portion of memory is reserved exclusively for console

-

"The console access is made available even in low memory " "condition. User can collect the details like tech-support " "for further diagnosis"

SYS-3-BAD_RESET

3-Error

Questionable reset of process [dec] on tty[t-line]\n

A process was reset without giving it a chance to clean itself up.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-TTY_EXPIRE_TIMER

6-Information

[chars] expired tty [dec] [inet] user [chars]

The maximum inactivity time has been reached for the tty session as configured by the exec-timeout CLI configuration command. The session has expired.

os

"This message is for information only. No action is" " required."

SYS-3-DUP_TIMER

3-Error

Same tty[t-line] in linewatch_timers type [dec]

A tty appeared twice in a timer list where it should have only appeared once.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-LINEPROCDEAD

2-Critical

Killing process [chars] associated with line [dec]

A process associated with a tty line was killed by another process. The line may go dead

exec

"If this messages recurs copy it exactly as it appears " "and report it to your technical support representative."

SYS-3-HTIMER_EXPAND

3-Error

timer heap at 0x[hec] needed to expand but hasn't

A timer heap should have expanded but has not

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_INIT

3-Error

heap timer at 0x[hec] has not been initialized

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_STATE

3-Error

heap timer at 0x[hec] in state [dec]

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-MUNMAP

2-Critical

Could not return memory Neutrino via munmap at %lx size [dec] errno [dec]

Failued to unmap memory memory at the indicated location. The memory could not be unmapped because it was allocated via mmap.

-

-

SYS-2-MMAP

2-Critical

mmap failed for size [dec] bytes Caller PC 0x[hec] errno [dec]

Failed to allocate memory for the requested size. The memory could not be mapped because there is no memory.

-

-

SYS-3-CERF_RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a cache error

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CERF_ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-PAK_SUBBLOCK_SETSIZE

2-Critical

[dec]

This message indicates an error in startup code to register a pak subblock size. An attempt was made to register a size after the subblock chunk pool had been initialized. This problem is caused by software initialization order.

-

-

SYS-3-RGCREATEFAIL

3-Error

Resource group creation failed\nCause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGADDFAIL

3-Error

Couldn't add process process pid [dec] to resource group [hec]\n Cause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGDELEFAIL

3-Error

Couldn't delete process process pid [dec] from resource group\n \nCause: [chars]

An attempt to remove a process from a resource group failed at the indicated location

-

-

SYS-3-RGDESTFAIL

3-Error

Couldn't destroy resource group [hec]\nCause: [chars]

An attempt to destroy a resource group failed at the indicated location

-

-

SYS-3-RGOPFAIL

3-Error

Requested memory thresholding operation on resource group failed\n Resource Group handle: [hec] Cause: [chars]

The message indicates that an request to Set/Get memory thresholding data or enable/disable thresholding failed in the indicated location

The component that issued the request

-

SYS-3-RGMEMEXCEED

3-Error

\nLimit Exceeded: [chars] Holding: %lu Requested:%lu bytes

A resource group has requested for more memory than the configured limit at the indicated location

The component to which the offending resource group belongs.

-

SYS-2-PAK_SUBBLOCK_BADSIZE

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. The requested size is larger than the maximum registered subblock size.

-

-

SYS-2-PAK_SUBBLOCK_ALREADY

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. A subblock was already associated with the packet.

-

-

SYS-3-IMAGE_TOO_BIG

3-Error

'[chars]' is too large for available memory [dec] bytes.

The allocated memory for the image is too small to hold the image file.

-

"Increase the amount of memory available in the router by booting " "with a smaller image not enabling non-essential sub-systems " "or upgrading the installed memory. Call your technical " "support representative for assistance."

SYS-2-BAD_BM_ARG

2-Critical

Invalid BM index boolean used as argument [dec]

An illegal boolean manager index argument was referenced

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-MAX_IDB_BM_EXCEEDED

2-Critical

BM bit allocation limit exceeded

The BM has exhausted all of the bits available for allocation

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-BAD_BM_NAME

2-Critical

Invalid BM name

An illegal name string was registered with the BM

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-ASSERTION_FAILED

2-Critical

Assertion failed: \[chars]\

An internal state consistency check failed. Correct operation cannot be guaranteed and the system has been halted.

-

LOG_STD_ACTION

SYS-6-STARTUP_CONFIG_IGNORED

6-Information

System startup configuration is ignored based on the configuration register setting.

The configuration register was set to ignore the system startup configuration.

-

"If the system should ignore the startup configuration no action " "is required. If the system should boot with the startup configuration " "saved in the NVRAM change the configuration register value."

SYS-3-URLREADFAIL

3-Error

cannot open file for reading '[chars]'

The URL for the cannot be opened for reading.

-

"Check for proper Uniform Resource Locator syntax and for read " "permission and retry."

SYS-3-TCLSETFAIL

3-Error

cannot set TCL interpreter variable '[chars]' to '[chars]' : '[chars]'

The value could not be passed to the TCL interpreter

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-ESMSHUTDOWN

7-Debug

ESM shutdown

The Embedded Syslog Manager has been shut down

-

LOG_STD_NO_ACTION

SYS-6-LOGGINGHOST_STARTSTOP

6-Information

Logging to host [chars][chars][chars][chars]

Syslog logging to specified server or hostvrf has started or stopped

os-logging

LOG_STD_NO_ACTION

SYS-4-CPURESRISING

4-Warning

[chars][chars] is seeing [chars] cpu util [dec]%% at [chars] level more than the configured [chars] limit [dec] %%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped. CPURESRISING notifications should be matched with the corresponding CPURESFALLING/CPURESUNAPPLY notification.

-

"No action is required"

SYS-6-CPURESFALLING

6-Information

[chars][chars] is no longer seeing [chars] high cpu at [chars] level for the configured [chars] limit [dec]%% current value [dec]%%

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required"

SYS-6-CPURESUNAPPLY

6-Information

[chars][chars] is no longer monitoring [chars] cpu at [chars] level for the configured [chars] limit.

CPU usage is no loger monitored for the configured threshold level mentioned in the error message The corresponding policy is revoked.

-

"No action is required"

SYS-3-BADLIST_DESTROY

3-Error

Removed a non-empty list[hec] name: [chars] having %lu elements

A non-empty list should not be destroyed. If it happens there is a possibility that all elements enqueued into the list will never be deallocated. This message reports that an non-empty list got destroyed.

Determine the component from the stack trace and process name displayed in the error message.

LOG_STD_ACTION

SYS-2-SYSMEMINFO

2-Critical

System Memory: %luK total %luK used %luK free

This is an auxiliary message to several memory-related messages. It\n\ provides system memory information usage.

-

"This message provides additional information only. Copy the error \n\ message exactly as it appears and report it to your technical support \n\ representative as part of a previously printed error message."

SYS-6-LOGGING_BUGINF

6-Information

Logging of buginf debugs was [chars]

All calls to debugging have been disabled in Cisco IOS software as a result the user entering the <CmdBold>no logging buginf<NoCmdBold> command. This command is used to avoid a situation where a large amount of debugging calls might overload the processor CPU hog condition. This

os-logging

"This is an informational message only. No action is required."

SYS-3-MEMLITE

3-Error

Free lite called for non lite chunk by '%p'

Memory lite error: free_lite_internal is passed a non lite chunk

mem

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SYS-5-PRIV_AUTH_PASS

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_AUTH_FAIL

5-Notice

Authentication to privilege level [dec] failed by [chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-FIFOBUS_ERR

5-Notice

Flow-control threshold on module [dec] has exceeded the default value. Threshold will be set to lower value

The FIFO threshold values are monitored for flow-control. When the threshold value exceeds the default the value is set to new lower value

Cat6000-env

LOG_STD_NO_ACTION

SYS-3-NV_BOOTVAR_PARSE

3-Error

Failed to parse boot command:[chars] Error:[dec]

Boot configuration failed to parse when copied to startup-config. Most likely reason would be syntax errors in the boot configuration.

none

"Decode the traceback and check configuration file for the boot " "commands. Boot commands are sandwiched between boot-start-marker " "and boot-end-marker"

SYS-5-PRIV_I

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-2-CZIP_ERROR

2-Critical

Error: [chars]

A software Error occurred while decompressing the Image. The actual error is within the string of the error message.

os

LOG_STD_SH_TECH_ACTION

SYS-4-SDB_SANITY_ERR

4-Warning

sanity check failed for string [chars]

The owner of this string must have freed their structure without letting the string database know

os-logging

"No action is required"

SYS-6-SCRIPTING_TCL_INVALID_OR_MISSING_SIGNATURE

6-Information

[chars] cannot run the signed TCL script.

The TCL script being run has either an unmatched trustpoint name or a missing or a corrupted trustpoint name

tcl-bleeding

"Either re-sign the TCL script with a proper trustpoint name or " "use crypto pki authenticate tcl to add the desired trustpoint name." "Then rerun the TCL script."

SYS-6-SCRIPTING_TCL_SECURE_TRUSTPOINT

6-Information

[chars] cannot verify signed TCL script.

The TCL script being run is lacking either scripting tcl secure-mode or trustpoint being configured first

tcl-bleeding

"Configure the missing scripting tcl secure-mode or " "scripting tcl trustpoint name <name>. Then rerun the TCL script."

SYS-1-LOGGING_THRESHOLD_EXCEEDED

1-Alert

Logging persistent unconfigured as threshold capacity is exceeded. device-name: [chars] threshold-cap: %lld logging-persistent size: %lld free: %lld

Automatically unconfigure logging persistent behaviour when threshold capacity is exceeded on the persistent storage.

syslog

"Common Criteria CC v.3.1 certification requirement force to halt the"

SYS-4-LOGGING_THRESHOLD_CHANGED

4-Warning

Logging persistent exceeded the threshold value and its space is full. The threshold capacity was changed to the default value. Oldest logging-persistent files will be deleted.

This log message to indicate when logging persistent command exceeded the specified size limitthreshold value and the old messages were overwritten.

syslog

"This message is for information however the " "user may consider to increase logging-persistent size or to " "delete old logging persistent files."

SYS-1-LOGGING_PER_SPACE_FULL

1-Alert

Logging persistent unconfigured as space is full. device-name: [chars] threshold-cap: %lld free: %lld

Automatically unconfigure logging persistent behaviour when there is no space left on the persistent storage.

syslog

"Common Criteria CC v.3.1 certification requirement force to halt "

SYS-1-LOGGING_WRITE_ERR

1-Alert

Logging persistent unconfigured as write error occur while writing to the persistent logging file [chars]

Automatically unconfigure logging persistent behaviour when write error occurs on the persistent storage.

syslog

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-SHOW_LOGGING

6-Information

User [chars] has activated the show [chars] command.

The Common Criteria CC certification requires a log message to indicate when a user activates the show logging persistent command.

os-logging

"This message is for information only. No action is required."

SYS-4-LOGGING_PERSISTENT_OVERRUN

4-Warning

Logging persistent command exceeded its size. Oldest logging-persistent file was deleted file name: [chars].

The Common Criteria CC certification requires a log message to indicate when logging persistent command exceeded the specified size limit and the old messages were overwritten.

os-logging

"This message is for information however the " "user may consider to increase logging-persistent size or to " "delete old logging persistent files."

SYS-6-LOGGING_MOVE

6-Information

User [chars] has activated the logging persistent move command.

The Common Criteria CC certification requires a log message to

os-logging

"This message is for information only. No action is required."

SYS-3-INTUNWEDGE

3-Error

%llu packets where forcefully unwedged %llu packets were forcefully deallocated

This is an auxiliary message to indicate that packet buffers were\n forcefully deallcoated/unaccounted from interfaces through CLI.

Include this error message in any other DDTS that was written for\n any other problems reported on this router after leak debugging\n was configured.

"This message is to explicitly notify that packets were forcefully\n" "deallocated/unaccounted. If the router is facing other problems\n" "for which you are contacting your technical support representative\n" "copy this error message to as it appears and provide this information\n" "too."

SYS-3-UNWEDGEDISABLED

3-Error

Policy map [chars] has been removed.\n Leak debugging on interface [chars] disabled.

This is error message indicates that the policy-map configured as\n filter in an interface for leak debugging has been removed without\n disabling the filter in the interface.

mem

"If the filter is required on the interface for debugging leaks\n" "reconfigure the policy-map and reconfigure the interface for\n" "leak debugging"

SYS-3-MEMSUSPENDDISALLOW

3-Error

[chars] called with request to suspend when it cannot suspend

A process which is currently in a state where it cannot relinquish the CPU invoked a memory management function that can relinquish control of the CPU

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the memory management function

-

SYS-3-BAD_TRIPCOUNT

3-Error

Traversed block count crossed the maximum possible count[dec]/[dec] in

A software error occurred. Value of tripcount has been zero or less which is harmful.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BAD_GLIBC_BUF_FREE

3-Error

A glibc buffer is freed in IOS buffer blockmagic: 0x[hec] flags 0x[hec]

A software error occurred. A glibc buffer is freed into IOS buffer pool.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-NVRAM_INIT_WAIT_TIME

7-Debug

Waited [dec] seconds for NVRAM to be available

The amount of time spent waiting during bootup before NVRAM was available.

-

"This is a debug message."

SCHED-2-NOATTR

2-Critical

Attempt to [chars] unknown process attribute [dec].

Each process has various attributes associated with it. This message indicates that an attempt was made to set or get a nonexistent process attribute.

-

LOG_STD_ACTION

SCHED-2-ATTRCMD

2-Critical

Attempt to [chars] attribute [chars] on process [dec].

Each process has various public and private attributes associated with it. This message indicates that an attempt was made to set or get a private attribute belonging to another process.

-

LOG_STD_ACTION

SCHED-2-ATTRVALUE

2-Critical

Attempt to set bad [chars] value [hec] on process [dec]

Each process has various attributes associated with it. This message indicates that an attempt was made to set the specified attribute to an invalid value.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SCHED-3-SEMLOCKED

3-Error

[chars] attempted to lock a semaphore already locked by itself

Some sections of code use semaphores to protect critical sections of software. This message indicates that an attempt was made to lock a semaphore that was already locked.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SCHED-2-SEMNOTLOCKED

2-Critical

[chars] attempted to unlock an unlocked semaphore

Some sections of code use semaphores to protect critical sections of\n\ software. This message indicates that an attempt was made to unlock a\n\ semaphore that was not locked.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-2-SEMUNLOCK

2-Critical

[chars] attempted to unlock semaphore owned by [chars] PID: [dec].

-

-

-

SCHED-2-EDISMSCRIT

2-Critical

Critical/high priority process [chars] may not dismiss.

Scheduler was running for a long time and so caused the system to reset

os

LOG_STD_RECUR_ACTION

SCHED-7-WATCH

7-Debug

Attempt to [chars] uninitialized watched [chars] address [hec].

A processes can register to be notified when various events occur. This message indicates that an attempt was made to register for an event without first creating the data structure for that event.

-

LOG_STD_RECUR_ACTION

SCHED-2-NOTWATCHTIMER

2-Critical

[chars] timer [hec] not being watched.

A process can register to be notified when various events occur in the\n\ router. This message indicates that an attempt was made to deregister a \n\ timer expiration event that is not currently registered.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-2-QUEUENOTEMPTY

2-Critical

Attempt to delete non-empty watched queue [chars] address [hec].

A process can register to be notified when various events occur in the\n\ router. This message indicates that an attempt was made to destroy a queue that\n\ still contained items. These items are lost and not returned to free\n\ memory.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-2-SETHIGHORCRIT

2-Critical

Attempt to set [chars] priority on process [dec] [chars]

Each process executes at a specified priority level. Higher priority\n\ processes must use the new scheduler primitives while lower priority\n\ processes can use primitives from either the new or old scheduler.\n\ This message indicates that an attempt was made to set the specified priority too\n\ high for a process using old scheduler primitives.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-UNEXPECTEDEVENT

3-Error

Process received unknown event maj [hec] min [hec].

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process received an event it\n\ did not know how to handle.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-UNEXPECTEDQUEUE

3-Error

Queue event for unknown queue index [dec].

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process received a queuing\n\ event for an unknown queue.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-UNEXPECTEDTIMER

3-Error

Unknown timer expiration timer = [hec] type [dec].

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process received a timer\n\ expiration event for an unknown timer.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-UNEXPECTEDMESSAGE

3-Error

Unknown message [hec] received ptr arg [hec] num arg [hec].

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process received a message from\n\ another process that it does not know how to handle.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-STACKSIZE

3-Error

Illegal stack size [dec] specified for process [chars].

Each process has its own stack space which must be one of several predefined sizes. This message indicates that an attempt was made to specify an illegal stack size.

-

-

SCHED-3-PRIORITY

3-Error

Illegal priority [dec] specified for process [chars].

Each process executes at a specified priority level. Higher priority\n\ processes must use the new scheduler primitives while lower priority\n\ processes can use primitives from either the new or old scheduler.\n\ This message indicates that an attempt was made to set the specified process \n\ to a priority level that is not allowed for the type of scheduler\n\ primitives used.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-PAGEZERO

3-Error

Low memory modified by [chars] [hex] = [hex]

In all Cisco products the first 256 bytes of memory are unused and are\n\ off limits. Newer platforms have hardware to immediately trap reads or\n\ writes to this area. Older platforms periodically check \n\ this memory. This message appears only on older platforms and\n\ indicates that this off-limits memory area was modified.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-LOSTWAKEUP

3-Error

Wakeup information for process [chars] lost maj [hec] min [hec].

A process can register to be notified when various events occur in the router. This message indicates that an event for the specified process was lost and that the system might not be functioning correctly.

-

-

SCHED-3-STUCKTMR

3-Error

Sleep with expired timer [hec] time %#Ta %TE ago.

A process can register to be notified when various events occur. This message indicates that a registered timer has expired and its value is unchanged after the process has received control twice.

-

-

SCHED-3-STUCKMTMR

3-Error

Sleep with expired managed timer [hec] time %#Ta %TE ago.

A process can register to be notified when various events occur. This message indicates that a registered timer has expired and its value is unchanged after the process has received control twice.

-

-

SCHED-3-THRASHING

3-Error

Process thrashing on watched [chars].

A process can register to be notified when various events occur. This message indicates that the indicated process relinquished control 50 consecutive times and there were still outstanding events to be processed.

-

-

SCHED-3-STILLWATCHING

3-Error

Process still watching [chars] [chars]

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process destroyed a set of\n\ events without first individually removing each event in the set.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-STILLWATCHINGT

3-Error

Process still watching [chars] timer [hec]

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process destroyed a set of\n\ events without first individually removing each event in the set.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SCHED-3-CORRUPT

3-Error

Scheduler '[chars]' corrupted by process [chars] expected [hec] found [hec]

-

-

-

SCHED-3-INTSETWAKEUP

3-Error

Invalid scheduler action [chars] at interrupt level

This message indicates that a process_set_wakeup_reasons was attempted from an interrupt handler.

-

"If this message recurs call your technical support representative for " "assistance."

SCHED-2-MESSAGE

2-Critical

Key [chars] does not match key [chars] of process [dec] in process_send_message request

An attempt was made to send a message to a process. The key associated with that process did not match the key in the message. This usually means an incorrect process id was used in the send message request.

Determine the component by extracting the first word in the first set of parantheses

-

SCHED-4-PROCESSTIME

4-Warning

Invalid argument [dec] msec for process_set_schedtime

This message indicates that there was an attempt to change the maximum time a process can run per scheduling to an invalid value. The value should range between 20msec to 200msec

Determine the component from the process name and the stack trace from the error message

-

SCHED-4-NO_PREEMPT_CTXT

4-Warning

[chars] is preempting [chars] without preemption context. Preemption is [chars] and [chars]. preempted_process_epc = 0x%p

This message indicates that the IOS scheduler is preparing to schedule a preemptive process but the preempted process does not have a preemption context allocated to it.

-

-

SCHED-5-INT_DISABLED_BEFORE_PREEMPTION

5-Notice

Detected interrupts being disabled in preemption handler. schedflag = [dec] forkx = [chars] preempted process = [chars]

This message indicates that the interrupt enable bit is unexpectedly found to be disabled in preemption handler before servicing the ready to run preemptive processes.

-

"If this message recurs just report it your technical support " "representative. However the functionality is not impacted. "

METS-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown\n\ or could not be handled.

analysis

LOG_STD_ACTION

METS-3-NOREGION

3-Error

No region found: [chars]

Resource failure: No region found.

analysis

LOG_STD_ACTION

METS-3-NULLPOOL

3-Error

Can't process null pool: [chars]

Resource failure: Null pool in the region

analysis

LOG_STD_ACTION

METS-2-INITFAIL

2-Critical

Can't start analysis

The requested operation failed due to lack of resource maybe temporarily

analysis

"Reduce system resource/memory usage and retry for the commands."

MEM_BLK-2-CTXERROR

2-Critical

The context information 0x%8x is not valid.

An application to the memory block manager has passed \n\ either a context pointer that is not valid.

memblkmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MEM_BLK-2-MEMBLKERROR

2-Critical

Memory block 0x%8x is not valid.

An application to the memory block manager has passed \n\ a memory block that is not valid.

memblkmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MEM_BLK-2-MEMFREEERROR

2-Critical

Memory block 0x%8x has already been freed.

An application to the memory block manager has attempted \n\ to free or lock a memory block that is not allocated.

memblkmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MEM_BLK-2-MEMTWINBLKERROR

2-Critical

An attempt to coalesce memory block 0x%8x with its \n\ sibling memory block 0x%8x has failed because the sibling\n\ block is not valid.

An attempt to coalesce two memory blocks\n\ has failed because a memory block is not valid.

memblkmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MEM_BLK-2-MEMORDINALERROR

2-Critical

The memory block manager has detected an ordinal error.\n\ Memory block 0x%8x has an ordinal of 0x%4x and a size of 0x%4x.\n\ Its corresponding lower sibling memory block 0x%8x has \n\ an ordinal of 0x%4x and a size of 0x%4x.

The lower sibling ordinal should be equal to the \n\ difference between the higher sibling's ordinal and \n\ size.

memblkmgr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-2-BADVERSION

2-Critical

Bad subsystem version number [dec] - ignoring subsystem

A software consistency check failed.

Determine the component from the subsystem displayed in the error message.

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-2-MISMATCH

2-Critical

Kernel and subsystem version differ [dec].[dec] - ignoring subsystem

A software consistency check failed.

Determine the component from the subsystem displayed in the error message.

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-2-BADCLASS

2-Critical

Bad subsystem class [dec] - ignoring subsystem

A software consistency check failed.

Determine the component from the subsystem displayed in the error message.

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-2-BADSEQUENCE

2-Critical

Subsystem [chars] has cross-class sequence for [chars]

A software or hardware error occurred.

Determine the component from the subsystem displayed in the error message.

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-2-RECURSION

2-Critical

Maximum sequence depth exceeded [dec] by [chars]

A software or hardware error occurred.

os

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-2-NOTFOUND

2-Critical

Subsystem [chars] needs subsystem [chars] to start

A software consistency check failed.

Determine the component from the subsystem that is in need as displayed in the error message.

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SUBSYS-3-PAGEZERO

3-Error

The [chars] class subsystem [chars] was being initialized.

In all Cisco products the first 256 bytes of memory is unused and off\n\ limits. Newer platforms have hardware to immediately trap reads or\n\ writes to this area. Older platforms periodically perform checks on\n\ this memory. This message appears only on older platforms and\n\ indicates that this off limits memory area was modified.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SUBSYS-3-NOAPIHOOK

3-Error

The API [chars] has no lookup hook for subsystems.

This process uses the named API but the process initialization\n\ code could not find the subsystem-initialization hook for this API.\n\ Process initialization cannot proceed without all hooks being present.

build

"Copy the error message exactly as it appears and report it\n\ to your technical support representative along with output from\n\ 'show tech'."

SUBSYS-3-UNORDERED

3-Error

The subsys class [dec][chars] has no initialization order.

The specified class subsystem has an unknown initialization order.

os

"Copy the error message exactly as it appears and report it " "to your technical support representative along with output from " "'show tech'."

SUBSYS-4-MALLOC

4-Warning

Class [chars] subsys [chars] bytes [dec] malloc [dec]

This message is only for tracking malloc/free in a subsys init.

-

"For development debugging only."

SERVER_CLOCK_SYNC-3-PORTCREATE

3-Error

cannot create port [chars] due to [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SERVER_CLOCK_SYNC-3-PORTOPEN

3-Error

cannot open port [chars] due to [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SERVER_CLOCK_SYNC-3-PORTREG

3-Error

cannot register port [chars] due to [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SERVER_CLOCK_SYNC-3-BADREQ

3-Error

bad request - [chars] - from client - [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SERVER_CLOCK_SYNC-3-LOCATE

3-Error

could not locate port [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SERVER_CLOCK_SYNC-3-LISTCREATE

3-Error

list creation failure

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SERVER_CLOCK_SYNC-3-CREATEBOOL

3-Error

watched boolean creation failure. bool [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

WARMUPGRADE-3-FILE

3-Error

Image file open/read failure.

Warm upgrade could not open or read from the image file specified

os

"Check whether the specified image is present at the desired location " "and has the required read permissions. If the location is remote " "check whether the connectivity is there."

WARMUPGRADE-3-FORMAT

3-Error

Unknown image file format.

Warm upgrade could not recognize the format of the image file

os

"Check whether the specified image is a valid IOS executable in\n\ a supported format. Check release notes for supported formats"

WARMUPGRADE-3-DECOMPRESS

3-Error

Image file decompression failure.

Warm upgrade could not decompress the image file

os

"Check whether the image file is complete and uncorrupted"

WARMUPGRADE-3-SIZE

3-Error

[chars] image size mismatch.

The size of the image in memory is different from the expected size

os

"Check whether the image file is complete and uncorrupted"

WARMUPGRADE-3-CHECKSUM

3-Error

[chars] image checksum mismatch.

The checksum of the image in memory is different from the expected \n\ checksum

os

"Check whether the image file is complete and uncorrupted"

CLIENT_CLOCK_SYNC-3-PORTCREATE

3-Error

cannot create port [chars] due to [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

CLIENT_CLOCK_SYNC-3-PORTOPEN

3-Error

cannot open port [chars] due to [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

CLIENT_CLOCK_SYNC-3-PORTREG

3-Error

cannot register port [chars] due to [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

CLIENT_CLOCK_SYNC-3-CREATEBOOL

3-Error

watched boolean creation failure. bool [chars]

An internal software error occurred.

os

"If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative."

DIGISIGN-4-SIGNATURE_NOT_PRESENT

4-Warning

%%WARNING: Digital signature is not found in file [chars]\n

The specified image file does not have a digital signature. Only Cisco IOS Software Images are digitally signed. If you enter <CmdBold>verify<NoCmdBold> <CmdBold>copy<NoCmdBold> or <CmdBold>reload<NoCmdBold> command and the specified file is not a digitally signed Cisco IOS Software Image the system displays this warning message because the file does not have a signature. A valid digital signature ensures the integrity of the image.

digi-sign-infra

"If the specified file is an unsigned Cisco IOS Software image " "be cautious when deciding " "whether or not to use this file. The system will not boot using " "this image."

DIGISIGN-3-VERIFICATION_FAILED

3-Error

%%ERROR: Digital signature verification failed for file [chars]: [chars]\n

Validation failure while verifying the digital signature.

digi-sign-infra

"Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered."

DIGISIGN-3-KEY_NOT_FOUND

3-Error

%%ERROR: No keys found for verifying the digital signature in file [chars]

No keys found in the device key storage for validating the digital signature. A valid key is needed to validate the digital signature in the image.

digi-sign-infra

"The device does not have a vlaid key to verify the digital" "signature. Open a case with the Technical Assistance Center" "via the internet at" "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered."

DIGISIGN-3-INVALID_SIGNATURE

3-Error

%%ERROR: Digital signature is not valid for file [chars]: [chars]\n

The specified Cisco IOS Software image has an invalid digital signature. A valid digital signature ensures the integrity of the image.

digi-sign-infra

"Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered."

DIGISIGN-4-INVALID_KEY

4-Warning

%%WARNING: Digital signature verification failed for file [chars]: [chars]\n

Validation failure due to invalid key while verifying the digital signature.

digi-sign-infra

"Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "device information you have gathered."

DIGISIGN-2-MISMATCH_KEYS

2-Critical

%%CRITICAL: System identified a mismatch between the show version output and the key type used in signing. [chars] is a signed [chars] software\n

System identified a mismatch in software type. This might be a modified software.

digi-sign-infra

"Do not use this file. The file might be corrupted or modified." "Open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "image and version information you have gathered."

DIGISIGN-3-DEVIMAGE_NOSUPPORT

3-Error

Cannot verify [chars] as it is signed with special key\n

The software image cannot be verified because it is signed with a special key.

digi-sign-infra

"To allow booting a specially-signed image use the" "software authenticity special command"

DIGISIGN-4-DEVIMAGE_CFG_NOSUPPORT

4-Warning

[chars] signed with special key will not be booted\n

With this configuration enabled the system will be unable to boot software that is signed with a special key.

digi-sign-infra

"Use the [no] form of this configuration no software authenticity special"

DIGISIGN-6-KEY_UPGRADE

6-Information

[chars]\n

System identified a key version mismatch between the key which was used to sign the image and the keys stored on the device

digi-sign-infra

"If the image is signed with a key version newer than the device" "keys then follow the procedure for key revocation which is" "which is documented at cisco.com. If the image is signed with a" "key version that is now obsolete please obtain the latest signed" "copy of this image from cisco.com"

DIGISIGN-3-INVALID_ENVELOPE

3-Error

%%ERROR: Failure in processing signature envelope for system image: [chars]\n

The loaded Cisco IOS software image has an invalid digital signature envelope. A valid digital signature envelope ensures the integrity of the image. The loaded Cisco IOS software image might be corrupted or modified. The failure type is one of the following: 1 Signature envelope version is not supported

digi-sign-infra

"Do not use this file. The file might be corrupted or modified." "Please attempt to copy the file again or download the file again " "from the http://www.cisco.com page before copying it." "If you continue to get this error message open a case with" "the Technical Assistance Center via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl and " "contact your Cisco technical support representative with the " "image and version information you have gathered."

DIGISIGN-4-FUR_BOOT

4-Warning

Field upgradable rommon used for key revocation\n

System identified that the field upgradable rommon was used to boot the image. It is recommended that the readonly rommon be used for the key revocation process.

digi-sign-infra

"Recommended action is to boot the image used for key revocation process " "with readonly rommon. This is a warning message." "Command/process will still go through in the current state."

DIGISIGN-3-OBSOLETE_SW

3-Error

[chars] software signed using obsolete key [chars]\n

System identified that a software was signed using an obsolete key. Key revocation cannot be possible when the system is still using a software signed using an obsolete key.

digi-sign-infra

"Please obtain the latest signed copy of this " "software from cisco.com and upgrade the system module."

DIGISIGN-3-NET_BOOT

3-Error

Netbooted software used for key revocation\n

System was netbooted using a software in a remote device. It is recommended to boot the system using a software in the local device for the key revocation process.

digi-sign-infra

"Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation."

DIGISIGN-3-WPG_BOOT

3-Error

Key revocation not allowed while running warm upgraded software\n

System was booted using warm upgrade. Key revocation process is not supported when the system is booted using warm upgrade. It is recommended to cold boot the system using a software in the local device for the key revocation process.

digi-sign-infra

"Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation."

DIGISIGN-4-DEV_IMAGE

4-Warning

[chars] software signed using special key version [chars]\n

System identified that a software was signed using special key. If this is unintentional please obtain the latest signed copy of the production software from cisco.com and upgrade the system module.

digi-sign-infra

"Get the latest signed copy of production image from cisco.com and upgrade " "the respective module"

ATM-1-NOPUSRAM

1-Alert

Unit [dec] not enough interface memory

The specified ATM interface hardware has run out of interface memory.

-

LOG_STD_SH_TECH_ACTION

ATM-3-MLPDEQUEUE

3-Error

MLPPP failed CosQ=[hec] MLP=[hec] OQDQ=[hec] [hec] Cause of the failure: [chars]

-

-

-

ATM-3-UNSUPPORTED_QOS_PARAMS

3-Error

ATM failed to create VC on Interface [chars]

Either the configuration contains invalid traffic shaping parameters or the software ran out of rate queues.

-

"Check the configuration for errors."

ATM-3-OUT_OF_VCDS

3-Error

ATM failed to create VC on Interface [chars]

The ATM subsystem ran out of internal resources necessary to create a new virtual circuit. This may indicate a software error.

-

LOG_STD_ACTION

ATM-4-UNMATCHUNIVERSION

4-Warning

[dec]/[dec]/[dec]:[dec]: [chars]. Please verify peer UNI version

The ATM peer equipment appears to be running an old version of ATM UNI. Communication with it is not possible.

-

"The peer equipment needs to be upgraded in " "order to communicate with this system."

ATM-4-MTUCALLMISMATCH

4-Warning

Call from: \n ATM NSAP - [chars]\n has mismatched PDU size - forward size is [dec]\n - backward size is [dec]\n int [chars] PDU size [chars] [chars]

The calling or called party has a maximum transmission unit MTU size

-

"Either change the configured MTU size on the current interface to that " "of the caller's or called party's interface or change the caller's or " "called party's interface to match the current interface."

ATM-2-FAILATMSWDB

2-Critical

Fail malloc atm_swdb at [chars]

System memory exhaustion caused an internal software error in the ATM subsystem.

-

"If the system exhibits any unexpected behavior as a result of " "this memory exhaustion it may need to be reset to clear the error." LOG_STD_REDUCE_ACTION

ATM-3-FAILREMOVEVC

3-Error

ATM failed to remove VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars]

-

-

-

ATM-3-FAILCREATEVC

3-Error

ATM failed to create VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars]

-

-

-

ATM-3-REJECTVC

3-Error

ATM failed to create VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars]

-

-

-

ATM-3-OVERSUBSCRIBED

3-Error

Interface [chars]: Total [chars] allocation [dec][chars] exceeded maximum [chars] of [dec][chars].

A software or hardware error occurred.

-

LOG_STD_ACTION

ATM-4-ILMIKEEPALIVEFAIL

4-Warning

ILMI[chars]: Restarting ATM signalling and ILMI. Keepalive failure detected.

Adjacent peer device is not responding to ILMI Keepalive polling.

-

"Check the connection of the ATM interface and the status of the " "adjacent peer device. Correct them if neccessary. Wait and check " "if ILMI Keepalive comes up again. If the problem persists " "copy this warning message exactly as it appears and report it to " "your technical support representative."

ATM-4-ILMICONFIGCHANGE

4-Warning

ILMI[chars]: Restarting ATM signalling and ILMI. Peer Configuration change detected.

Configuration of adjacent peer device has been changed.

-

"Wait for the interface to restart itself."

ATM-4-VPIVCIRANGE

4-Warning

VPI/VCI range parameters are dis-joint on [chars]

MinSvccVci > MaxVci after negotiation with the peer through ILMI.

-

"Disable auto-cinfiguration on both sides and change the " "port configuration appropriately so that SVCCs can be setup."

ATM-5-ATMSOFTSTART

5-Notice

Restarting ATM signalling and ILMI on [chars].

The command just entered causes ATM Soft Restart.

-

"Stand by and let ATM Signalling and ILMI to restart."

ATM-6-ILMINOAUTOCFG

6-Information

ILMI[chars]: Auto-configuration is disabled current

The command just entered causes auto-configuration to be disabled the most recently entered interface parameters will be used at next interface restart.

-

"Be aware of what parameteres have been configured."

ATM-6-ILMIAUTOCFGALREADY

6-Information

ILMI[chars]: Auto-configuration already enabled.

Atm auto-configuration has been enabled already. 'atm auto-configuration' command just entered is ignored.

-

"No action required."

ATM-6-ILMINOAUTOCFGALREADY

6-Information

ILMI[chars]: Auto configuration already disabled.

Atm auto-configuration has been enabled already. 'no atm auto-configuration' command just entered is ignored.

-

"No action required."

ATM-6-ILMIAUTOCFGENABLEERR

6-Information

ILMI[chars]: Auto-configuration cannot be enabled.

Auto-configuration cannot be enabled if there are some conflicting configuration on an interface. Like if there are VCs with vpi > 255 auto-configuration cannot be done till these VCs are removed as with auto-configuration enabled vpi > 255 cannot be supported.

-

"Undo the conflicting configuration on the interface for " "this command to succeed."

ATM-5-ILMIADDREG

5-Notice

Address registration on [chars] is enabled.

The command just entered enables atm address registration.

-

"No action required."

ATM-5-ILMIACCFILTER

5-Notice

New access filter setting will be applied to registration of new addresses on [chars].

The command just entered sets up new ilmi access filter for address registration. It only affects new addresses to be registered. The addresses already registered will not be affected.

-

"Enter the shutdown and no shutdown commands on this interface to " "restart address registration if need to remove addresses already " "registered but not permitted by the new access filter."

ATM-5-ILMIDEFACCFILTER

5-Notice

New global default access filter setting will be applied to registration of new addresses on interfaces using global default access filter.

The command just entered sets up new global default access filter for addres registration. It only affects new addresses to be registered on interfaces using the global default. The addresses already registered will not be affected.

-

"Enter the shutdown and no shutdown commands on desired " "interfaces to restart address registration if need to remove addresses " "already registered but not permitted by the new global " "default access filter."

ATM-4-STUCK_VCD

4-Warning

clearing stuck VCD [dec] from map on [chars]

A SVC map entry has a stuck VCD attached to it which has been previously cleared in the driver.

-

"No action required as the stuck VCD condition is detected " "and cleared."

ATM-5-UPDOWN

5-Notice

Interface [chars] Changing autovc [dec]/[dec] to [chars]

The ATM Auto VC is either created removed activated \n\ or deactivated.

-

"No action required if status change is intended\n\ otherwise the cause for status change may deserve to be noticed.\n\ The shut and no shut CLI command deactivates/activates VC."

ATM-3-MLPOATM_ERROR

3-Error

MLPoATM not configured properly on \n\ Link [chars] Bundle [chars] :[chars]

The configuration of MLPPP-over-ATM MLPoATM on the ATM PVC is either incorrect or incomplete.

atmcommon

"Ensure that the service policy has been attached to " "the Virtual Template and that the queueing strategy on the ATM interface " "is per VC queueing and queueing algorithm is FIFO. To verify the " "configuration use the <CmdBold>show inteface atm <noCmdBold> and " "<CmdBold>show running-config virtual-template<noCmdBold> commands."

ATM-6-ILMITERMINATINGPORT

6-Information

ILMI[chars]: This command does not apply to internal terminating port.

Internal terminating does not need to be configured with this command. The command just entered is ignored.

-

"No action required."

ATM-3-ILMISYNCINTERNERR

3-Error

[chars] [chars]:[dec]

Internal Error see message occurs during ILMI Primary to Secondary Sync

as

LOG_STD_SH_TECH_ACTION

ATM-3-ILMISYNCINTFERR

3-Error

[chars] [%08X=[chars]] [chars]:[dec]

Internal Error see message occurs during ILMI Primary to Secondary Sync

as

LOG_STD_SH_TECH_ACTION

ATM-4-ILMISYNCINTFWARN

4-Warning

[chars] [%08X=[chars]] [chars]:[dec]

Recoverable Internal Error see message occurs during ILMI Primary to Secondary Sync

as

LOG_STD_SH_TECH_ACTION

ATM-3-ILMIINTERNALERR

3-Error

[chars] [chars]:[dec]

Internal Error see message occurs during ILMI Primary to Secondary Sync

as

LOG_STD_SH_TECH_ACTION

ATM-5-ILMIINTFREDUNDENCY

5-Notice

ILMI[chars]: [chars]

Informational Message for ILMI Redundency Support

as

LOG_STD_SH_TECH_ACTION

ATM-5-ILMIREDUNDENCY

5-Notice

[chars]

Informational Message for ILMI Redundency Support

as

LOG_STD_SH_TECH_ACTION

ATM-3-ATM_WAVL_TREE_ERROR

3-Error

ATMNode1 [chars] VCD [dec] [dec]/[dec] Node2 [chars] VCD [dec] [dec]/[dec]

A software error occured.

-

LOG_STD_SH_TECH_ACTION

ATM-6-AUTOPPP

6-Information

ATM[chars]: VCVCD=[dec] VPI=[dec] VCI=[dec] Auto Detected Encap Type is [chars].

ATM VC AutoPPP Encapsulation Type has been changed automatically`.

atmcommon

"don't do anything."

ATM-6-PVC_STATE_CHANGE

6-Information

ATM[chars]: PVCVCD=[dec] VPI=[dec] VCI=[dec] state changed to [chars].

ATM PVC status has changed.

-

LOG_NO_ACTION

ATM-3-PPPOEOA_VCFLAG

3-Error

ATM: [chars] PVC [dec]/[dec] : Error in PPPoE flag

The ATM PVC PPPoE flag is still set while it should not be set. ATM uses a flag to indicate whether or not it should process PPPoE frames. In some rare conditions the flag can still be set for ATM to process PPPoE frames while it should not be. This condition can cause PPPoE frames to be processed when they should be dropped.

atmcommon

"In most cases no action is required as the system will set the flag " "so that ATM will not process PPPoE frames and the system " "will continue to operate normally. However If the ATM PVC " "specified in the error message is repeatedly experiencing problems " "involving PPPoE unconfigure all commands under the PVC " "and remove and then reconfigure the PVC. Enter the " "<CmdBold>interface atm<NoCmdBold> interface.subinterface-number " "command in global configuration mode to enter atm interface " "configuration mode. Then specify the PVC you would like to " "unconfigure and enter the <CmdBold>no encapsulation<NoCmdBold> " "command. Specify the PVC you just unconfigured then reconfigure " "the PVC using the <CmdBold>encapsulation<NoCmdBold> command."

ATM-1-ISSU_NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

atmcommon

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

ATM-3-ISSU_SENDFAILED

3-Error

\nATM ISSU: send message failed rc = [dec]\n

The sending of a message has failed.

atmcommon

LOG_STD_SH_TECH_ACTION

ATM-4-ISSU_INCOMPATIBLE

4-Warning

\natm-issu-compat: returned FALSE

The compatibility checking has failed

atmcommon

LOG_STD_SH_TECH_ACTION

ATM-4-ISSU_XFORM

4-Warning

\n[chars]: failed rc=[chars]

The transform has failed.

atmcommon

LOG_STD_SH_TECH_ACTION

ATM-3-FAILREMOVESERVICEPOLICYONATMVC

3-Error

ATM failed to remove service policy on VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars]

The DSL line rate has been changed for the PVC to support the guaranteed bandwidth configured for the virtual circuits.

atmcommon

LOG_STD_ACTION

CCPROXY-3-UNREGISTERED_BY_GK

3-Error

\ H.323 Proxy registration is being removed by Gatekeeper [chars]\n Check \show proxy h323 status\ for details.

-

-

-

CCPROXY-3-NOBLOCK_EVENT

3-Error

\ During initialization of proxy [chars]: cannot allocate event block\n

-

-

-

CCPROXY-3-NOMEMORY_FRAGMENT_CACHE

3-Error

\ [chars]: failed to allocate cache for fragmented packets for fastswitch

-

-

-

CCPROXY-3-NOINIT_OSS_h225

3-Error

\ [chars]: initializing h225 socket failed through ASN.1 library: error=[dec]\n

-

-

-

CCPROXY-3-NOINIT_OSS_h245

3-Error

\ [chars]: initializing h245 socket failed through ASN.1 library: error=[dec]\n

-

-

-

CCPROXY-3-NOCCAPI_INTERFACE

3-Error

\ CCAPI new interface is not created in [chars]\n

-

-

-

CCPROXY-3-NOPROCESS_CCPROXY

3-Error

\ The proxy process is not created in [chars]\n

-

-

-

CCPROXY-3-NOCCB_FROM_CALLID

3-Error

\ No call-control-block is found in [chars] for [hec].\n

-

-

-

CCPROXY-3-NOMM_INTERFACE

3-Error

\ No multimedia interface configured in [chars].\n

-

-

-

CCPROXY-3-NOCALL_ccIFInService

3-Error

\ No proxy CCAPI interface found: H.323 proxy bringup failed in [chars].\n

-

-

-

CCPROXY-3-NO_CONNECT_TABLE

3-Error

\ Unable to allocate memory for [dec] connection table entries in [chars].\n

-

-

-

CCPROXY-3-NO_RASREQ_TABLE

3-Error

\ Unable to allocate memory for [dec] RAS request table entries in [chars].\n

-

-

-

CCPROXY-3-STRCALLHISFAIL

3-Error

[chars]: Unable to store Call History record

-

-

-

GK_OSP-3-GK_OSP_INIT_NOMEM

3-Error

\ Not enough emory to initialize GK_OSP subsystem: [chars].

Unable to initialize the gatekeeper OSP subsystem because of low memory conditions.

-

"Upgrade memory capacity on the router."

GK_OSP-3-GK_OSP_PARSE_CHAIN_FAIL

3-Error

\ Could not install gatekeeper osp CLI.

An internal error has occured.

-

"None. Please report this to customer support."

GK-3-GK_SRV_LISTEN_FAIL

3-Error

\ Failed to open Gatekeeper Server listening socket.

-

-

-

GK-3-GK_TMSG_NOMEM

3-Error

\ No memory for gk-server transport message block.

-

-

-

GK-3-PROC_NOTDOWN

3-Error

\ Invalid state [chars]: bringup is only permitted after shut down.

-

-

-

GK-3-PROC_NOTUP

3-Error

\ Invalid state [chars]: shutdown is only permitted after bringup.

-

-

-

GK-3-PROC_CB_NOMEM

3-Error

\ No memory for process control block. Gatekeeper bringup failed.

-

-

-

GK-3-PROC_MSGCB_NOMEM

3-Error

\ No memory for IPC message control block. Gatekeeper bringup failed.

-

-

-

GK-3-PROC_LRQARRAY_NOMEM

3-Error

\ No memory for lrq array. Gatekeeper bringup failed.

-

-

-

GK-3-PROC_MSGRING_NOMEM

3-Error

\ No memory for msgring. Gatekeeper bringup failed.

-

-

-

GK-3-PROC_EV_NOMEM

3-Error

\ No memory for free event queue. Gatekeeper bringup failed.

-

-

-

GK-3-PROC_NOCREAT

3-Error

\ Unable to create gatekeeper process. Gatekeeper bringup failed.

-

-

-

GK-4-PROC_NOTALL

4-Warning

\ Unable to create more than [dec] gk thread processes.

-

-

-

GK-3-NO_RAS_PORT

3-Error

\ Unable to open or bind to RAS well-known port. Bringup failed.

-

-

-

GK-3-NO_DISC_PORT

3-Error

\ Unable to open or bind to gatekeeper discovery port. Bringup failed.

-

-

-

GK-3-ZONE_NOT_FOUND

3-Error

\ Zone not found for specified Gatekeeper name [chars].

-

-

-

GK-3-ZONE_ACTIVE

3-Error

\ There are endpoints currently registered in zone [chars]. Zone remove failed

-

-

-

GK-3-EXCEED_MAX_LOCAL_ZONE_ALLOWED

3-Error

\ Exceeded maximum number of local zones [dec] allowed.

-

-

-

GK-3-SUBNET_NOT_FOUND

3-Error

\ Subnet not found under specified IP address [inet]/[inet].

-

-

-

GK-3-SUBNET_FAILED

3-Error

\ Failed to add/modify subnet information for specified subnet [inet]/[inet].

-

-

-

GK-3-SUBNET_NO_ATTRIBUTES

3-Error

\ Please specify attribute [default | explicit] for this command.

-

-

-

GK-3-CANNOT_TURN_OFF_ATTRIB

3-Error

\ Subnet attributes are currently turned ON for\n

-

-

-

GK-3-ENDPT_NOT_FOUND

3-Error

\ Endpoint not found for specified IP address [inet].

-

-

-

GK-3-GW_PROXY_IP_NOT_FOUND

3-Error

\ GW/Proxy not found for specified IP adddress [inet].

-

-

-

GK-3-GW_PROXY_ALIAS_NOT_FOUND

3-Error

\ GW/Proxy not found for specified alias name [chars].

-

-

-

GK-3-GW_PROXY_ADD_COST_FAIL

3-Error

\ GW/Proxy add cost failed. Could be out of memory.

-

-

-

GK-3-GW_PROXY_ENDPT_NOT_FOUND

3-Error

\ GW/PROXY may not be registered. Add cost failed.

-

-

-

GK-3-PARTIAL_STATIC_ALIAS

3-Error

\ Not all aliases were successfully created. Use the \show gatekeeper endpt\ command to check on successful aliases.

-

-

-

GK-3-STATIC_ALIAS_FAILED

3-Error

\ static-alias command failed. Could not create endpoint in endpoint dbase.

-

-

-

GK-3-STATIC_ALIAS_GW_FAILED

3-Error

\ A static endpoint was added into the database but failed to create a gateway.\n

-

-

-

GK-3-INVALID_GK_CMD

3-Error

\ To shutdown Gatekeeper use the \shutdown\ command in the Gatekeeper mode.

-

-

-

GK-3-CONFLICTING_DATA

3-Error

\ Static-alias command failed. Endpoint already exists with different [chars].\n Use the \show gatekeeper endpoints\ command to check on existing endp\n\oints.

-

-

-

GK-3-SHUTDOWN_WITH_CALLS

3-Error

\ Cannot shutdown gatekeeper because there are calls in progress.

-

-

-

GK-3-MSGCB_TIMER_RUNNING

3-Error

\ Message CB freed while timer still running: msgcb state=[dec] status=[dec] timer type=[dec]

-

-

-

GK-3-ALTGK_CONFIG_ERROR

3-Error

\ An error in the alternate gatekeeper configuration was detected. Remote gatekeeper [chars] claims to be part of zone [chars]

-

-

-

GK-3-ALTGK_CONFIG_ERROR_LOCAL

3-Error

\ An alternate gatekeeper indicates an alt-gk configuration error on a local zone.\n

-

-

-

GK-3-GK_GUP_INIT_ERROR

3-Error

\ An error occurred trying to initialize the Gatekeeper Update Protocol GUP.

-

-

-

GK-6-GK_CLI_RAS_IP_CHANGED

6-Information

\ The IP address which\n has been changed was the gatekeeper's configured RAS address.\n Existing RAS clients will no longer be able to reach the gatekeeper.\n

The IP address being changed at the interface was statically assigned to the gatekeeper for its RAS signaling via the \zone local\ command. This action will automatically replace the gatekeeper's static RAS address with the new IP address. Since the gatekeeper's old RAS address is no longer valid existing clients which have registered to this gatekeeper via the old RAS address will no longer be able to communicate with this gatekeeper.

-

"It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display"

GK-6-GK_CLI_RAS_IP_REMOVED

6-Information

\ The IP address which\n has been removed was the gatekeeper's configured RAS address. The\n system will automatically assign a new IP address if available to\n

The IP address being removed at the interface was statically assigned to the gatekeeper for its RAS signaling via the \zone local\ command. This action will automatically remove the gatekeeper's static RAS address. Since the gatekeeper no longer has a configured RAS address the router will automatically assign an IP address if there is any to the gatekeeper. Existing clients which have registered to

-

"It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display"

GK-6-GK_FLOAT_RAS_IP_CHANGED

6-Information

\ The gatekeeper's RAS address\n has been automatically changed by the system. Existing RAS clients\n may no longer be able to reach the gatekeeper.\n

The IP address being changed at the interface causes the system to look for a better IP address to be used for the gatekeeper's RAS address. existing clients which have registered to this gatekeeper via the old RAS address may no longer be able to communicate with this gatekeeper.

-

"It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display"

GK-6-GK_CLOSE_SRV_CONNECTION

6-Information

\ The connection to GKTMP server [chars][inet] appears to be hung

Messages are being backed up in the gatekeeper's write queue in the connection with the specified server name. The connection is assumed to have gone bad and the gatekeeper is closing the connection. This implies that messages will not be sent to that server for processing until either the gatekeeper or the server re-initiates the connection.

-

"Check with the specified server for possible connection error."

GK-5-GKTMP_SERVER_ONLINE

5-Notice

GKTMP Server: [chars][chars] is connected with Gatekeeper: [chars]

A connection between a GKTMP server and a gatekeeper has been\n\ established. The connection establishment could be initiated by\n\ either the Gatekeeper or a GKTMP server.

voice-h323

LOG_STD_NO_ACTION

GK-3-GKTMP_SERVER_OFFLINE

3-Error

GKTMP Server: [chars][chars] is disconnected with Gatekeeper: [chars]

-

voice-h323

"Check the operational status of the Gatekeeper and the GKTMP\n\ server. If both are operational check the TCP connection between\n\ the server and the Gatekeeper. Check the output of the <CmdBold>show\n\ running-config<NoCmdBold> and <CmdBold>show gatekeeper\n\ servers<NoCmdBold> and verify the status of the GKTMP server. Enter\n\ the <CmdBold>debug gatekeeper server<NoCmdBold> command on the\n\ Gatekeeper to enable debugging on the gatekeeper server. Collect\n\ this information contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

GK-3-GKTMP_SERVER_MARKED_UNUSABLE

3-Error

GKTMP Server: [chars][chars] connected to GK: [chars] is marked unusable

The Gatekeeper has marked a GKTMP server as unusable when flow\n\ control is configured.The reason for this action could be that the\n\ average response time of the GMTMP server is very high or the number\n\ of messages queued to be sent to the GKTMP server is very high. These\n\ conditions could be caused by an overloaded server or a problem with\n\ the TCP connection between the server and the Gatekeeper.

voice-h323

"Check the operational status of of the GKTMP server and the\n\ network link between the server and the Gatekeeper. If both are\n\ operational enter the <CmdBold>show running-config<NoCmdBold> and\n\ <CmdBold>show gatekeeper servers<NoCmdBold> commands and verify\n\ the status of the GKTMP server. Enter the <CmdBold>debug gatekeeper\n\ server<NoCmdBold> on the Gatekeeper to enable debugging on the\n\ gatekeeper server. Gather this information contact your Cisco\n\ technical support representative and provide the representative\n\ with the gathered information."

GK-5-GKTMP_SERVER_MARKED_USABLE

5-Notice

GKTMP Server: [chars][chars] connected to GK: [chars] is marked usable

The Gatekeeper has marked the GKTMP server as usable when flow\n\ control is configured.

voice-h323

LOG_STD_NO_ACTION

GK-5-RX_LRQ_PASSWORD_UPDATED

5-Notice

\ LRQ receive password for security password-group '[chars]' has been updated.

The Gatekeeper was configured with a LRQ security password-goup that contained the 'effective' keyword. This keyword allows the user to specify a time at which the requested password is to take effect. The log is displayed to inform the user that the time period has expired and the updated password is now in effect.

-

"This log is only for informational purposes. The user should verify " "that all remote zones associated with this password-group are now " "providing the password in its LRQ messages. Failure to do so will " "result in a LRJ containing a reason of invalid_permission."

GK-6-LRQ_ACL_BLOCKED_MSG

6-Information

\ LRQ from IP [chars] was blocked by LRQ access list

-

-

-

GK-6-ARQ_ACL_BLOCKED_MSG

6-Information

\ AnswerCall ARQ with source IP [chars] was blocked by ARQ access list

-

-

-

HTTPC-3-PROC_NOCREAT

3-Error

\ Unable to create HTTP Client process.

-

-

-

HTTPC-3-OUTOF_MEM

3-Error

\ HTTP Client out of memory.

-

-

-

HTTPC-3-CACHE_MEM

3-Error

\ HTTP Client Cache Init out of memory.

-

-

-

HTTPC-3-INIT_FAIL

3-Error

\ HTTP Client Process Init failed.

-

-

-

HTTPC-3-OUTOF_SYNC

3-Error

\ HTTP Client header tables out of sync.

-

-

-

HTTPC-6-CONNECT_FAILED

6-Information

\ The connection to server [inet] failed

-

-

-

HTTPC-3-RECEIVE_SOCK_READ_EVENT_WHILE_DISABLED

3-Error

\ Received socket read event while read interest is disabled callID[dec] fd[dec] - closing socket.

The HTTP Client is receiving the socket READ event while the READ interest is being disabled. Something has gone wrong between the http client and the socket interfaced.

-

"Record the error and report it to the system administrator."

HTTPC-3-CONNECT_NULL

3-Error

\ NULL connection structure for fd[dec] - closing socket.

The HTTP Client is receiving the socket READ event but it fails to locate the connection structure for this file descriptorfd.

-

"Record the error and traceback and report it to the system administrator."

HTTPC-6-REQUEST_FAILED

6-Information

\ request URI [chars] failed

-

-

-

HTTPC-6-CLOSE_SRV_CONNECT

6-Information

\ The connection to server [inet] appears to be hung and will be closed.

Messages are being backed up in the HTTP Client's write queue in the connection with the specified server. The connection is assumed to have gone bad and the HTTP Client is closing the connection.

-

"Check with the specified server for possible connection error."

HTTPC-3-COOKIE_MEM

3-Error

\ HTTP Client runs out of allowable memory to store cookies.

The total memory allocated for storing cookies has run out. All cookies received from the HTTP server will be dropped. Users may no longer be able to interact with a session-based origin server until memory is freed up.

-

"Users may want to try their requests at a later time or contact the " "system administrator to increase the maximum RAM allowed for saving " "HTTP cookies."

VOICE_RC-5-DSP_REMOVED

5-Notice

DSP ID:[dec] removed from service after [dec] reset within [dec] minutes

Notification message.

-

"dsp might be badopy the error message exactly\n\as it appears and report it to your technical support representative"

VOICE_RC-5-DSP_RESET

5-Notice

DSP ID:[dec] reset

Notification message.

-

"IOS reset dsp due to possible dsp error"

DSPDUMP-5-DUMPSTART

5-Notice

DSP [dec] 0x[hec] in slot [dec] starting dump

The DSP resource is beginning crash dump collection

-

LOG_STD_NO_ACTION

DSPDUMP-5-RX_CONTROL_DROP

5-Notice

DSP [dec] in slot [dec] Rx Control Message Dropped by DSP

The DSP has reported that a Rx Control Message was dropped

-

LOG_STD_NO_ACTION

DSPDUMP-5-TX_CONTROL_DROP

5-Notice

DSP [dec] in slot [dec] Tx Control Message Dropped by DSP

The DSP has reported that a Tx Control Message was dropped

-

LOG_STD_NO_ACTION

HPI-3-FAILED_START

3-Error

channel:[chars] DSP ID:0x[hec] failed mode [dec] for service [dec]

Failed to start DSP services

ios-voice

LOG_STD_ACTION

HPI-3-INVALID_PAYLOAD

3-Error

wrong payload size channel:[chars] DSP ID:0x[hec] failed mode [dec] for service [dec]

Failed to start DSP services

ios-voice

LOG_STD_ACTION

HPI-3-CODEC_NOT_LOADED

3-Error

channel:[chars] DSP ID:0x[hec] command failed as codec not loaded [dec]

Sending messages to DSP without a loaded codec can result with the DSP failing

ios-voice

LOG_STD_ACTION

HPI-4-INVALID_CODEC_LOAD

4-Warning

channel:[chars] DSP ID:0x[hec] invalid hpi mode [dec] for loading codec [dec]

Attempt to load codec when the DSP is in an invalid mode which can result with DSP failure

ios-voice

LOG_STD_ACTION

HPI-4-NO_CLOSE

4-Warning

channel:[chars] DSP ID:0x[hec]

Attempt to release DSP without sending close message

ios-voice

LOG_STD_ACTION

HPI-4-INVALID_ECAN_TYPE

4-Warning

[chars] ECAN is not available in voice-card [dec] [chars] ECAN will be used

All voice cards participated in DSPFarm must have the same echo canceller type

-

"Make sure all voice cards participated in DSPFarm have the same echo canceller type configured"

HPI-3-GSMAMRNB_LICENSE_NOT_ACTIVATED

3-Error

\n********************************************************* \ \nGSM AMR-NB License is not yet activated. \ \nPlease configure 'license feature gsmamrnb-codec-pack' \ \nand accept the EULA to activate the license. \ \n*********************************************************\n

Failed to start DSP services for GSM AMR-NB codec

ios-licensing-atg

LOG_STD_ACTION

HPI-6-SRTP_EVAL_LIMIT

6-Information

The SRTP bandwidth and tunnels usage exceed the license limits

The SRTP bandwidth and tunnels exceed the license limits

xformers-csl

LOG_STD_NO_ACTION

HPI-3-SRTP_EVAL_FREE_ERROR

3-Error

Error encountered on release SRTP bandwidth and tunnels reservation

Error encountered on release SRTP bandwidth and tunnels

xformers-csl

LOG_STD_NO_ACTION

HPI-3-NACK_HIGH

3-Error

DSP to IOS Nack message with severity [chars] [chars] [chars]

DSP to IOS Nack message with high severity

ios-voice

-

HPI-4-NACK_MED

4-Warning

DSP to IOS Nack message with severity [chars] [chars] [chars]

DSP to IOS Nack message with medium severity

ios-voice

"Check the NACKed message's parameters for " \"minor configuration errors. "

HPI-6-NACK_LOW

6-Information

DSP to IOS Nack message with severity [chars] [chars] [chars]

DSP to IOS Nack message with low severity

ios-voice

"Information only displaying NACKed messages " \"that are for debugging purposes."

HPI-6-NACK

6-Information

DSP to IOS Nack message [chars] [chars]

DSP to IOS Nack message with no severity in order to work with dspware without Nack severity implementation

ios-voice

"Information only displaying NACKed messages."

SGCP-2-INTERNAL_CRITICAL

2-Critical

[chars]

The SGCP subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

SGCP-3-INTERNAL_ERROR

3-Error

[chars]

The SGCP subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

SGCP-4-INTERNAL_WARNING

4-Warning

[chars]

The SGCP subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

RSCMSM-3-NO_SUCH_INTERFACE

3-Error

\ [chars]: The interface doesn't exist

The interface for resource measurement doesn't exist at the time of the operation.

call-treatment

"Check the configuration to see if that interface is there"

RSCMSM-5-TEST_ALREADY_RUNNING

5-Notice

\ One test is already running.

there is already one test running at the same time.

call-treatment

"Please wait for the completeness of the running test before starting " "another test. "

RSCMSM-3-NO_LIST_CREATED

3-Error

\ [chars]: Cannot create interface-based rsc list.

This failure is due to the list create operation.

ios-mem

"Please check the memory at the moment."

CALL_CONTROL-6-MAX_CONNECTIONS

6-Information

Maximum number of connections reached for dial-peer [dec]\n

The dial-peer in question has reached its maximum connections configurations. No more calls will be taken on this dial-peer.

voice-callcontrol

"No action is required however to increase the number of connections " "allowed to this dial peer see 'maximum connections' configuration under " "the dial-peer configuration mode."

CALL_CONTROL-6-APP_NOT_FOUND

6-Information

Application [chars] in dial-peer [dec] not found. Handing callid [dec] to the alternate app [chars].\n

The inbound dial-peer points to an unavailable application. The call is being handed to the alternate application or is rejected.

voice-callcontrol

"Reconfigure the dial-peer to have a valid application name or verify " "the application is accesible at its location."

CALL_CONTROL-6-APP_NOT_EXIST

6-Information

The requested application does not exist any more. The event for the callid [dec] is being discarded.\n

The event points to a session application which does not exist any more. The event is being discarded.

voice-callcontrol

"No action is required for the users"

CALL_CONTROL-6-NUMBERING_TYPE_NO_MATCH

6-Information

The called number numbering type did not match The event for the callid [dec] is being discarded.\n

The event points to a session application which does not exist any more. The event is being discarded.

voice-callcontrol

"No action is required for the users"

CALL_CONTROL-3-NORAWMSG

3-Error

no free raw msg structure available from [chars] for signaling message

There were no rawmsg structures remaining in the system pools to alert the\n\ router of a voice or signaling event.

voice-callcontrol

"Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port."

CALL_CONTROL-3-CCAPI_DB_ERR

3-Error

ccapi database error

Internal CCAPI conference or call record database error. This message represents an internal software fault and may manifest itself as dropped or hung calls.

voice-callcontrol

"Contact your technical support representative include the full text of\n\ the error message."

CALL_CONTROL-6-CALL_LOOP

6-Information

The incoming call has a global identifier already present in the list of currently handled calls. It is being refused.\n

The incoming call has a global identifier already present in the list of currently handled calls. It means that the voice gateway has detected a loop in the call route.

voice-callcontrol

"Please check your configuration."

CALL_CONTROL-6-UNKNOWN_EXT_AGENT_RESET_ATTEMPT

6-Information

Request to reset an uknown external agent ID [dec] attempted.

A request to reset an external agent eg H323 Gatekeeper or MGCP CA etc

voice-callcontrol

LOG_STD_ACTION

CALL_CONTROL-3-INVALID_PARAMETER

3-Error

An invalid parameter is passed to the function

This is due to coding error.

voice-callcontrol

"No action is required for the users"

CALL_CONTROL-3-STAT_MEMORY_CORRUPTED

3-Error

Memory corruption detected in memory=[hec] allocated for RTCP statistic

This is due to coding error

voice-callcontrol

"No action is required for the users"

CISCO_STUN-3-QUEUE_ERROR

3-Error

Unable to enqueue event [chars] [dec] to a process watched queue. Current size: [dec] max size: [dec]

-

-

-

CISCO_STUN-3-PARSE_ERROR

3-Error

Parsing of STUN message received on IP address [chars] and port [dec] failed with value [dec]

Parsing of one of STUN attribute failed due to invalid value or not present or received STUN message has invalid header

ipipgw

LOG_STD_RECUR_ACTION

CISCO_STUN-3-INTERTNAL_ERROR

3-Error

Unable to process STUN message received on IP address [chars] and port [dec] failed with value [dec]

Unable to processs the received STUN packet. Could be due to no ICE instance present to handle this packet or the STUN message has a wrong method or stray packet

ipipgw

LOG_STD_RECUR_ACTION

CISCO_STUN-3-NORESOURCE

3-Error

No resources for [chars]

An error was encountered while trying to obtain memory resources for an internal queue or table. If malloc errors where also seen then that is most likely the root of the problem. If no memory allocation errors have occurred then this may be an internal problem.

ipipgw

"If there were memory allocation errors at the" "same time as this error then this error can be ignored. Otherwise: " LOG_STD_SH_TECH_ACTION

CISCO_STUN-4-INVALID_MESSAGE_INTEGRITY

4-Warning

Invalid Message-Integrity attribute in the received STUN message on UDP IP address [chars] port [dec]

A STUN messages received has a wrong Message-Integrity. This could mean the sending device has not computed the integrity of the STUN payload before it sends out Or it has changed the payload after it has computed the integrity and hence the integrity is wrong. CUBE has not honoured this STUN message and has responded with STUN error response with a error code 400 as per RFC 5389

ipipgw

LOG_STD_NO_ACTION

CISCO_STUN-4-INVALID_USERNAME

4-Warning

Invalid USERNAME attribute in the received STUN message on UDP IP address [chars] port [dec]

A STUN messages received has a wrong USERNAME attribute and does not comply with RFC 5245. CUBE has not honoured this STUN messsage and has responded with a STUN error response have ERROR-ATTRIBUTE value 400

ipipgw

LOG_STD_NO_ACTION

CISCO_STUN-4-ICE_ROLE_CONFLICT

4-Warning

Ice Role Conflcit detected in the received STUN message on UDP IP address [chars] port [dec]

A STUN messages received has a role-conflcit determined as per procedures of RFC 5245. CUBE has responded with a ERROR-CODE attribute of with a value of 487 Role Conflict but retains its role.

ipipgw

LOG_STD_NO_ACTION

E911-4-CALLBACK_UNREACHABLE

4-Warning

Unable to contact the last emergency caller at [chars].

A call has been made to an emergency response number. \n\ This message simply informs system administrators of the call.

voice-ivr

"The administrator determines the policy for\n\ outbound emergency calls. The administrator\n\ may set-up an application to page or email\n\ a technician everytime this message is emitted."

E911-3-MISSING_DEFAULT_NUMBER

3-Error

It is mandatory to configure an ELIN under 'voice emergency response settings.'

The administrator has enabled the Enhanced 911 feature without configuring\n\ a default ELIN under 'voice emergency response settings.'

voice-ivr

"The administrator should enter the 'voice emergency response settings' \n\ mode and configure a value for the 'elin' CLI."

MGCP_RF-3-RF_REG_FAILED

3-Error

RF registration for the MGCP RF client failed with return code [dec]

The MGCP RF client failed to register properly with RF. This should not occur and should be reported.

mgcp-redundancy

LOG_STD_ACTION

MGCP_RF-3-SEND_MSG_FAILED

3-Error

The MGCP RF client failed to send a message to the peer system op [dec]

The MGCP RF client could not send a message to the peer Standby or Active system and bulk synchronization may not be complete.

mgcp-redundancy

LOG_STD_ACTION

UC_SAF-3-COMM_INT_ERR

3-Error

Internal error occurred: [chars]

-

voice-saf

"If the error is due to lack of memory check the size of free memory" " to make sure there is enough to run SAF service"

UC_SAF-3-COMM_OUTOFSYNC_ERR

3-Error

[chars] error occurred with client [[chars]] on channel[[dec]]

COMM process is out of sync with client

voice-saf

"Disable/delete the channel and retry the operation. " "If that does not help then shutdown and restart the " "client's SAF service"

UC_SAF-3-COMM_ENCODE_ERR

3-Error

[chars] while encoding element [chars]

Error occurred while trying to encode the client supplied data

voice-saf

"Modify the element that failed to encode using " "client's configuration clis"

UC_SAF-3-COMM_FWDR_REG_ERR

3-Error

[chars] for operation [chars] for client [[chars]] on channel [[dec]]

Error occurred while trying to request an action from SAF Forwarder

voice-saf

"If the failure is due to lack of memory then check the size of" " free memory to ensure there is enough memory to run SAF service. " "If the failure is due to invalid AS or vrouter name check the values" "configured in the client with those of the Forwarder. " "If the error is due to mismatch between client and forwarder then" " undo the current operation and retry"

UC_SAF-3-COMM_FWDR_ERR

3-Error

[chars] for operation [chars] on instance [[dec].[dec].[dec].[dec]] sub-service [[dec]] for client [[chars]] on channel [[dec]]

Error occurred while trying to request an action from SAF Forwarder

voice-saf

"If the failure is due to lack of memory then check the size of" " free memory to make sure there is enough memory to run SAF service. " "If the error is due to mismatch between client and forwarder then" " undo the current operation and retry. " "If the error is due to publish data is too large then reduce the amount of" " data to be advertised and retry"

UC_SAF-3-COMM_NOTIFY_ERR

3-Error

[chars] for operation [chars] on instance [[dec].[dec].[dec].[dec]] sub-service [[dec]] for client [[chars]] on channel [[dec]]

Error occurred while acting upon a notification from SAF Forwarder

voice-saf

"If the failure is due to lack of memory then check the size of" " free memory to make sure there is enough memory to run SAF service. " "If the error is due to invalid data received in the SAF advertisement " "turn on error debugs and re-publish the service from the specified " "instance. Based on the information in the error debugs check and correct " "the configuration on the remote publisher"

UC_SAF-3-COMM_DECODE_ERR

3-Error

[chars] while decoding [chars]

Error occurred while trying to decode the SAF advertisement

voice-saf

"Turn on error debugs and re-publish the specified " "instance. Based on the information in the error logs check and correct " "the configuration on the remote publisher"

UC_SAF-6-COMM_CHANNEL_UNREG

6-Information

[chars] for client [[chars]] on channel [[dec]] could not be completed because channel was unregistered

The most likely reason could be that the forwarder sent REGISTRATION notification message to UC SAF COMM process which causes the channel to be unregistered. Any messages from VSAF client in the interim for that channel will fail

voice-saf

"Take the necessary steps to re-instate the vrouter" " configurations. Then do shut followed by no shut " "on VSAF channel cli"

UC_SAF-3-VSAF_CLIENT_INSV_ERR

3-Error

Could not bring voice saf client in service\n

Failed to instantiate client abstraction or initialization/ registration with other support modules has failed while voice service saf command was executed

voice-saf

"Check the size of free memory to make sure there is enough memory " "to run SAF service"

UC_SAF-3-VSAF_CLIENT_PROCESS_CONTROL_ERR

3-Error

Client process event loop detected - [chars]

Invalid state or unexpected events detected at the client manager process execution

voice-saf

LOG_STD_ACTION

UC_SAF-3-VSAF_CLIENT_TASK_QUEUE_ERROR

3-Error

Unable to enqueue task event [chars] [dec] to process watched queue

-

-

-

UC_SAF-3-VSAF_CLIENT_COMM_QUEUE_ERROR

3-Error

Unable to enqueue uc-comm event [chars] [dec] to process watched queue

-

-

-

UC_SAF-3-VSAF_CLIENT_TASK_BAG_ERROR

3-Error

Error while performing task bag [chars] corresponding to task event [dec] job.

A transient object that carries task parameters could not be instantiated or is corrupted. This may result in improper execution of the associated task which inturn can affect the ongoing operation.

voice-saf

"Check the size of free memory to make sure there is enough memory."

UC_SAF-3-VSAF_CLIENT_SUBS_NOTIFICATION_ERROR

3-Error

Error while adding or updating subscription notification from instance [dec]:[dec].[dec].[dec].[dec]

Subscription notification received from the specified instance could not be added in the database. This could be because none of the advertised patterns were found to be valid or trunk-route parameters were invalid or the SAF DN database was already full.

voice-saf

"If the error is due to invalid advertisement " "turn on error debugs and re-publish the specified instance. " "Based on the error logs check and correct the configuration " "on the remote publisher "

UC_SAF-6-VSAF_CHANNEL_REGISTER

6-Information

Client channel id [dec] is [chars]\n

Configured voice saf operational state

voice-saf

"If the channel went down unintentionally it is probably " "due to misconfiguration resulting in error. Check if the " "configured channel arguments matches those under router " "eigrp command level. Do shut/no shut under the channel " "to reset the voice saf channel operations"

UC_SAF-6-VSAF_SERVICE_WITHDRAWN_INVALID_PROFILE

6-Information

Service [chars] [dec] with inst-id <[dec].[dec].[dec].[dec]> has been withdrawn due to

Withdrawal of service triggered due to change in state of configured profile.

voice-saf

"If the service was unintentionaly withdrawn it was probably " "due to certain critical parameters missing in the profile or " "if the state of the hardware used in the profile is down. " "Say ip interface state used in the trunk-route is down. " "Please verify and re-do the publish command from the config or " "exec level."

UC_SAF-6-VSAF_SERVICE_PUBLISH_INVALID_PROFILE

6-Information

Attempted publish of service [chars] [dec] with tag [dec] failed due to invalid

The user or system triggered service advertisement failed due to the detection of invalid or incomplete profile.

voice-saf

"Please check for the completeness of the service profile " "constructs. If they look ok pls check the status of the " "interfaces used under the trunk-route profile session " "parameters."

UC_SAF-3-VSAF_CLIENT_INTERNAL

3-Error

[chars]

An internal software error has occurred

voice-saf

LOG_STD_SH_TECH_ACTION

DSM-6-SESSION_DATABASE_FAILED

6-Information

Cannot create DSM session database\n

Failed to create DSM session.

ios-voice

"Check the size of free memory to make sure there is enough memory."

DSM-3-MSGSNDFAIL

3-Error

channel:[chars] DSP ID:0x[hec] Message ID:0x[hec]

A message could not be sent to the DSP. The session continued but may have experienced problems.

ios-voice

"Contact your technical " "support representative include the full text of the error message."

DSM-3-NOEVENT

3-Error

no free event structure available from [chars] for DSM message

There were no event structures remaining in the system pools to alert the router of a voice or signaling event.

ios-voice

"Contact your technical support " "representative include the full text of the error message."

DSM-3-DSPALARM

3-Error

channel [chars] DSP ID 0x[hec]: status=0x[hec] message=0x[hec] text=[chars]

The DSP reported a fatal error. All sessions on the DSP were dropped and a DSP reload was attempted.

ios-voice

"Contact your technical support\n\ representative include the full text of the error message."

DSM-3-DSP_TIMEOUT

3-Error

DSP timeout on channel [chars] event 0x[hec]: DSP ID=0x[hec]: [chars]

Timeout on DSP response.

ios-voice

"The DSP has been automatically reset. If problem persists contact" "your technical support representative"

DSM-3-INTERNAL

3-Error

Internal Error : [chars]

DSM Internal error

ios-voice

"Contact your technical support representative"

CALLTREAT_NOSIGNAL-3-HIGH_CPU_ONE_MIN_LOAD

3-Error

System experiencing high cpu utilization over one minute interval.\n

Based on the average CPU utilization over a 60 second interval \n\ the system does not have enough CPU resources available.

call-treatment

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the <CmdBold>show proc cpu<NoCmdBold>\n\ command to see which processes are consuming\n\ the most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ resource allocation if the five-second CPU utilization on the gateway exceeds 98%. "

CALLTREAT_NOSIGNAL-3-HIGH_CPU_5SEC_LOAD

3-Error

System experiencing high cpu utilization.\n

System does not have enough CPU resources available to allocate \n\ a new resource.

call-treatment

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the <CmdBold>show proc cpu<NoCmdBold>\n\ command to see which processes are consuming the most CPU\n\ capacity and if appropriate reduce other system activity to \n\ ease CPU demands. By default the system will reject calls \n\ if the five-second CPU utilization on the gateway exceeds 89%. \n\ The default value can be overridden by enabling call treatment \n\ and entering the <CmdBold>call threshold global cpu-5sec<NoCmdBold> \n\ command."

CALLTREAT_NOSIGNAL-3-HIGH_CPU_AVERAGE_LOAD

3-Error

System experiencing high average cpu utilization.\n

Based on the average CPU utilization over a 60-second interval or an\n\ interval configured through the <CmdBold>call threshold\n\ poll-interval<NoCmdBold> command the system does not have \n\ enough CPU resources available to accept a new call.

call-treatment

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Check to see if the current call setup\n\ rate is supported on this gateway. Enter the <CmdBold>show proc\n\ cpu<NoCmdBold> command to see which processes are consuming the \n\ most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%.\n\ The default value can be overridden by enabling call treatment and\n\ entering the <CmdBold>call threshold global cpu-avg<NoCmdBold>\n\ command."

CALLTREAT_NOSIGNAL-3-HIGH_IOMEM_USAGE

3-Error

System running low on I/O memory.\n

The system does not have enough free I/O memory.

call-treatment

"Ensure that the gateway has the recommended amount of I/O memory\n\ for this Cisco IOS feature set and version. Enter the \n\ <CmdBold>show mem<NoCmdBold> and <CmdBold>show proc mem<NoCmdBold> \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for I/O memory utilization can be\n\ configured by enabling call treatment and entering the\n\ <CmdBold>call threshold global io-mem<NoCmdBold> command."

CALLTREAT_NOSIGNAL-3-HIGH_PROCMEM_USAGE

3-Error

System running low on processor memory.\n

The system does not have enough free processor memory.

call-treatment

"Ensure that the gateway has the recommended amount of processor memory\n\ for this Cisco IOS feature set and version. Enter the \n\ <CmdBold>show mem<NoCmdBold> and <CmdBold>show proc mem<NoCmdBold>\n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for processor memory utilization can be\n\ configured by enabling call treatment and entering the\n\ <CmdBold>call threshold global proc-mem<NoCmdBold> command."

CALLTREAT_NOSIGNAL-3-HIGH_TOTAL_CALLS

3-Error

High call volume.\n

The system is experiencing a high call volume.

call-treatment

"Disable call threshold modify the call threshold global\n\ high and low values or investigate the cause of the high resource\n\ utilization. The high and low thresholds for total number of calls\n\ can be configured by enabling call treatment and entering the\n\ <CmdBold>call threshold global proc-mem<NoCmdBold> command."

CALLTREAT_NOSIGNAL-3-HIGH_MEMORY_USAGE

3-Error

System running low on memory.

The system does not have enough free memory to allocated new resource.

call-treatment

"Ensure that the gateway has the recommended amount of memory for\n\ this Cisco IOS feature set and version. Enter the \n\ <CmdBold>show mem<NoCmdBold> and <CmdBold>show proc mem<NoCmdBold> \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ By default the system will reject calls if there is less than 2% free\n\ processor memory on the gateway. This value can be overridden by \n\ enabling call treatment and entering the\n\ <CmdBold>call threshold global total-mem<NoCmdBold> command."

CALLTREAT-3-HIGH_CPU_ONE_MIN_LOAD

3-Error

System experiencing high cpu utilization over one minute interval. Processing for callID[dec] is rejected.\n

Based on the average CPU utilization over a 60 second interval \n\ the system does not have enough CPU resources available to accept\n\ a new call. The specified call was rejected.

call-treatment

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the <CmdBold>show proc cpu<NoCmdBold>\n\ command to see which processes are consuming\n\ the most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%. "

CALLTREAT-3-HIGH_CPU_5SEC_LOAD

3-Error

System experiencing high cpu utilization. Processing for callID[dec] is rejected.\n

System does not have enough CPU resources available to accept\n\ a new call. The specified call was rejected.

call-treatment

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the <CmdBold>show proc cpu<NoCmdBold>\n\ command to see which processes are consuming the most CPU\n\ capacity and if appropriate reduce other system activity to \n\ ease CPU demands. By default the system will reject calls \n\ if the five-second CPU utilization on the gateway exceeds 89%. \n\ The default value can be overridden by enabling call treatment \n\ and entering the <CmdBold>call threshold global cpu-5sec<NoCmdBold> \n\ command."

CALLTREAT-3-HIGH_CPU_AVERAGE_LOAD

3-Error

System experiencing high average cpu utilization. Processing for callID[dec] is rejected.\n

Based on the average CPU utilization over a 60-second interval or an\n\ interval configured through the <CmdBold>call threshold\n\ poll-interval<NoCmdBold> command the system does not have \n\ enough CPU resources available to accept a new call. The specified \n\ call was rejected.

call-treatment

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Check to see if the current call setup\n\ rate is supported on this gateway. Enter the <CmdBold>show proc\n\ cpu<NoCmdBold> command to see which processes are consuming the \n\ most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%.\n\ The default value can be overridden by enabling call treatment and\n\ entering the <CmdBold>call threshold global cpu-avg<NoCmdBold>\n\ command."

CALLTREAT-3-HIGH_IOMEM_USAGE

3-Error

System running low on I/O memory. Processing for callID[dec] is rejected.\n

The system does not have enough free I/O memory to accept a new call.\n\ The specified call was rejected.

call-treatment

"Ensure that the gateway has the recommended amount of I/O memory\n\ for this Cisco IOS feature set and version. Enter the \n\ <CmdBold>show mem<NoCmdBold> and <CmdBold>show proc mem<NoCmdBold> \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for I/O memory utilization can be\n\ configured by enabling call treatment and entering the\n\ <CmdBold>call threshold global io-mem<NoCmdBold> command."

CALLTREAT-3-HIGH_PROCMEM_USAGE

3-Error

System running low on processor memory. Processing for callID[dec] is rejected.\n

The system does not have enough free processor memory to accept a new\n\ call. The specified call was rejected.

call-treatment

"Ensure that the gateway has the recommended amount of processor memory\n\ for this Cisco IOS feature set and version. Enter the \n\ <CmdBold>show mem<NoCmdBold> and <CmdBold>show proc mem<NoCmdBold>\n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for processor memory utilization can be\n\ configured by enabling call treatment and entering the\n\ <CmdBold>call threshold global proc-mem<NoCmdBold> command."

CALLTREAT-3-HIGH_TOTAL_CALLS

3-Error

High call volume. Processing for callID[dec] is rejected.\n

The system is experiencing a high call volume. There are not\n\ enough resources to accept a new call. The specified call was \n\ rejected.

call-treatment

"Disable call threshold modify the call threshold global\n\ high and low values or investigate the cause of the high resource\n\ utilization. The high and low thresholds for total number of calls\n\ can be configured by enabling call treatment and entering the\n\ <CmdBold>call threshold global proc-mem<NoCmdBold> command."

CALLTREAT-3-HIGH_MEMORY_USAGE

3-Error

System running low on memory. Processing for callID[dec] is rejected.\n

The system does not have enough free memory to accept a new call. \n\ The specified call was rejected.

call-treatment

"Ensure that the gateway has the recommended amount of memory for\n\ this Cisco IOS feature set and version. Enter the \n\ <CmdBold>show mem<NoCmdBold> and <CmdBold>show proc mem<NoCmdBold> \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ By default the system will reject calls if there is less than 2% free\n\ processor memory on the gateway. This value can be overridden by \n\ enabling call treatment and entering the\n\ <CmdBold>call threshold global total-mem<NoCmdBold> command."

VTSP-3-NOEVENT

3-Error

no free event structure available from [chars] for DSP message

There were no event structures remaining in the system pools to alert the\n\ router of a voice or signaling event.

ios-voice

"Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port."

VTSP-3-CAPABILITYMISMATCH

3-Error

voice port [chars]: call connection id [0x[hec] 0x[hec] 0x[hec] 0x[hec]]

There was a capabilities mismatch between the two call legs.\n\ capabilities are negotiated between call legs for CODEC VAD and\n\ FAX rate.

ios-voice

"Check that the dial peer configuration is appropriate for the interface\n\ in question. Also check that and configuration on the interface is\n\ correct."

VTSP-3-DSPALARM

3-Error

channel [chars] DSP ID 0x[hec]: status=0x[hec] message=0x[hec] text=[chars]

The DSP reported a fatal error. All calls on the DSP were dropped\n\ and a DSP reload was attempted.

ios-voice

"Verify that the DSP reloaded properly by attempting to place a call\n\ on the affected voice port. Contact your technical support\n\ representative include the full text of the error message."

VTSP-3-FSM_ERROR

3-Error

[chars]

Internal Finite State Machine Error.

ios-voice

"Contact your technical support representative include the full text of\n\ the error message."

VTSP-3-DSP_TIMEOUT

3-Error

DSP timeout on channel [chars] event 0x[hec]: DSP ID=0x[hec]: [chars] call mode=[dec]

Timeout on DSP response.

ios-voice

"The DSP has been automatically reset. If problem persists contact" "your technical support representative"

VTSP-4-FSM_BAD_EVENT

4-Warning

Invalid FSM Input on channel [chars]: state=[chars] event=[dec]

Internal state machine illegal input. This message represents an internal software fault and may manifest itself as dropped or hung calls.

ios-voice

"Contact your field service representative if indication is coincident " "with dropped or hung calls."

VTSP-3-DOCALLHISFAIL

3-Error

\nvtsp_do_call_history: [chars]

Allocate or insert an active VTSP call record into call history list failed.

ios-voice

"No action is required."

VTSP-3-MSGSNDFAIL

3-Error

channel:[chars] DSP ID:0x[hec] Message ID:0x[hec]

A message could not be sent to the DSP. The call continued but may\n\ have experienced problems.

ios-voice

"Verify that the DSP is still functioning properly by attempting\n\ to place a call on the affected voice port. Contact your technical\n\ support representative include the full text of the error message."

VTSP-3-VTSP_BLOCK

3-Error

vtsp_call_block allocate failed

VTSP call block allocation failed.

ios-voice

"Add more memory"

VTSP-3-VTSP_CALL_INFO_CHUNK

3-Error

VTSP callInfo chunk creation failed.

Creation of VTSP callInfo chunk failed due to lack of memory.

voice-sig-digital

"Add more memory."

VTSP-3-VTSP_DB_ERR

3-Error

vtsp_call_block database error

Internal VTSP call block database error. This message represents an internal software fault and may manifest itself as dropped or hung calls.

ios-voice

"Contact your technical support representative include the full text of\n\ the error message."

VTSP-3-VTSP_HAIRPINN

3-Error

hairpin peer cdb does not exist cdb 0x[hec] dst_call_id [dec]

A hairpin call setup failed because the other call leg does not exist.

ios-voice

"Contact your technical support representative. Report the configuration and the full text of the error message."

VTSP-3-VTSP_HAIRPIN_NOTPOSSIBLE

3-Error

Call can't be hairpinned. cdb 0x[hec] dst_cdb 0x[hec] dst_call_id [dec]

A DSP-less call could not be hairpinned.

ios-voice

"Check the dial-peer configuration."

VTSP-3-VTSP_HAIRPIN_FAILED

3-Error

Call hairpinning failed. cdb 0x[hec] dst_cdb 0x[hec] dst_call_id [dec]

A DSP-less call could not be hairpinned.

ios-voice

"Under heavy traffic this failure may happen because no TDM resources were\n\available. Contact your technical support representative include the full text of the error message."

VTSP-3-VTSP_CALL_DISC_FAILED

3-Error

VTSP call disconnect failed. channel id [chars] ret [dec]

VTSP call disconnect could not be successfully passed and it may result\n\ hung calls.

ios-voice

"Contact your technical support representative. Report the configuration\n\ and full text of the error message."

VTSP-4-VTSP_PLAR_TIE_FAILED

4-Warning

VTSP connection plar tie set up failed. channel id [chars] cause [dec]

Connection plar tie set up failed for non-normal reason

ios-voice

"Contact your technical support representative. Report the configuration\n\ and full text of the error message."

VTSP-6-UNKNOWN_EXT_AGENT_RESET_ATTEMPT

6-Information

Request to reset an uknown external agent ID [dec] attempted.

A request to reset an external agent eg H323 Gatekeeper or MGCP CA etc

ios-voice

LOG_STD_ACTION

VTSP-6-LONG_DUR_CALL_DETECTED

6-Information

Long Duration Call is detected [chars]\n

The call is active for configured duration of long call

ios-voice

LOG_STD_ACTION

VTSP-2-H320_MATCH_CALL_QUEUE_ERROR

2-Critical

Memory corruption is found on H.320 Primary Call Match Data Queue. Queue Size=[dec]

Failed to match an H.320 primary call for an incoming call due to memory curruption.

ios-voice

"Contact your technical support representative. Report the configuration\n\ and full text of the error message."

FALLBACK-4-CACHE_OVERFLOW

4-Warning

Function name [chars]: Cache has overflowed.

Fallback cache has overflowed and dumped 1/4 of the entries.

-

"Increase the fallback cache size."

FALLBACK-3-CACHE_FULL

3-Error

Function name [chars]: Cache is full

Fallback cache has overflowed and unable to dump entries

-

"Increase the fallback cache size."

FALLBACK-5-TEST_PROBE_ALREADY_RUNNING

5-Notice

A test probe is already running.

Only one test probe may run at a time.

-

"Wait until the first test probe is finished."

FALLBACK-3-NO_RTP_PORT

3-Error

Function name [chars]: No available RTP ports.

No available voice RTP ports were found.

-

LOG_STD_NO_ACTION

FALLBACK-3-NO_STATS

3-Error

[chars]: No stats were returned.\n

No statistic information was returned with probe

-

LOG_STD_NO_ACTION

FALLBACK-3-PROBE_FAILURE

3-Error

A probe error to [inet] occured - [chars]

A probe error occured. Possibly responder on remote router is not enabled or no machine is on specified IP

-

"Check the destination router."

FALLBACK-3-MALLOC_FAIL

3-Error

[chars]: Memory allocation failed.

Allocation of memory failed. This is possibly due to the fact that system memory pool is exhausted.

-

LOG_STD_NO_ACTION

FALLBACK-3-RTR_CREATE_FAIL

3-Error

[chars]: Creation of probe failed. Return code [dec]

An RTR probe could no be created. This can cause inaccurate ICPIF values and cause VoIP calls to be hairpined when they should not

-

LOG_STD_NO_ACTION

FALLBACK-3-RTR_START_FAIL

3-Error

[chars]: probe could not be started. Return code [dec]

An RTR probe could no be started. This can cause inaccurate delay/loss/jitter and icpif values and cause VoIP calls to be hairpined when they should not

-

LOG_STD_NO_ACTION

FALLBACK-3-RTR_STATS_FAIL

3-Error

[chars]: Could not retrive statistics from the probe. Return code [dec] \n

Could not retrive RTR statistics from the probe. This can cause inaccurate ICPIF values and cause VoIP calls to be hairpined when they should not

-

LOG_STD_NO_ACTION

FALLBACK-3-INTERNAL_ERROR

3-Error

[chars]: Internal error.

An internal error occured.

-

LOG_STD_NO_ACTION

FALLBACK-5-AVBO_PROBE

5-Notice

A probe to [inet] is [chars] - codec [chars] icpif [dec] loss [dec] delay [dec]

AVBO rtr proble status change.

-

"use the grace_period option to avoid trasit error"

RAI-1-INITSYS

1-Alert

[chars]

The specific message text is supplied by the RAI Subsystem. This indicates an initialization failure. When this occurs RAI is not operational.

voice-sip

LOG_STD_ACTION

L2CAC-5-VC_BW_NOT_ENOUGH

5-Notice

VC [dec]/[dec] bandwidth is not enough to add this Trunk portchannel. Total bandwidth is [dec] cps but requires [dec] cps to add this Trunk portchanel

VC bandwidth is not enough Need to increase the bandwidth .

-

"To support this call VC bandwidh the sustained cell rate has to be increased to accomidate the new calls."

SDP-3-CONFIG_PTR_ERROR

3-Error

Received invalid config pointer from application. Unable to process.

The SDP library application has an invalid configuration pointer. The SDP library is therefore unable to handle the request that it received. The configuration of the application will not be as expected and SDP parsing errors may result even for valid SDPs.

voice-sdp

LOG_STD_ACTION

SDP-3-SDP_PTR_ERROR

3-Error

Received invalid SDP pointer from application. Unable to process.

The SDP library application has an invalid SDP pointer. The SDP library is therefore unable to handle the request that it received. SDP parsing or build errors may result.

voice-sdp

LOG_STD_ACTION

SDP-3-INTERNAL

3-Error

[chars]

An internal software error has occurred.

voice-sdp

LOG_STD_SH_TECH_ACTION

TCMSP-3-NOEVENT

3-Error

no free event structure available from [chars] for DSP message

There were no event structures remaining in the system pools to alert the router of a voice or signaling event.

ios-voice

"Check that the voice port for which the event was reported is still operational. If not clear the voice port."

TCMSP-3-CAPABILITYMISMATCH

3-Error

voice port [chars]: call connection id [0x[hec] 0x[hec] 0x[hec] 0x[hec]]

There was a capabilities mismatch between the two call legs. capabilities are negotiated between call legs for CODEC VAD and FAX rate.

ios-voice

"Check that the dial peer configuration is appropriate for the interface in question. Also check that and configuration on the interface is correct."

TCMSP-3-DSPALARM

3-Error

DSP ID 0x[hec]: status=0x[hec] message=0x[hec] text=[chars]

The DSP reported a fatal error. All calls on the DSP were dropped and a DSP reload was attempted.

ios-voice

"Verify that the DSP reloaded properly by attempting to place a call on the affected voice port. Contact your technical support representative include the full text of the error message."

TCMSP-3-FSM_ERROR

3-Error

[chars]

Internal Finite State Machine Error.

ios-voice

"Contact your technical support representative include the full text of the error message."

TCMSP-3-DSP_TIMEOUT

3-Error

DSP timeout on event 0x[hec]: DSP ID=0x[hec]: [chars] call mode=[dec]

Timeout on DSP response.

ios-voice

"The DSP has been automatically reset. If problem persists contact" "your technical support representative"

TCMSP-4-FSM_BAD_EVENT

4-Warning

Invalid FSM Input on channel [chars]: state=[chars] event=[dec]

Internal state machine illegal input. This message represents an internal software fault and may manifest itself as dropped or hung calls.

ios-voice

"Contact your field service representative if indication is coincident " "with dropped or hung calls."

TCMSP-3-DOCALLHISFAIL

3-Error

\ntcmsp_do_call_history: [chars]

Allocate or insert an active TCMSP call record into call history list failed.

ios-voice

"No action is required."

TCMSP-3-MSGSNDFAIL

3-Error

channel:[chars] DSP ID:0x[hec] Message ID:0x[hec]

A message could not be sent to the DSP. The call continued but may have experienced problems.

ios-voice

"Verify that the DSP is still functioning properly by attempting to place a call on the affected voice port. Contact your technical support representative include the full text of the error message."

TCMSP-3-TCMSP_BLOCK

3-Error

tcmsp_call_block allocate failed

RBTreeCreate failed.

ios-voice

"Add more memory"

TCMSP-3-TCMSP_HAIRPINN

3-Error

hairpin peer cdb does not exist cdb 0x[hec] dst_call_id [dec]

A hairpin call setup failed because the other call leg does not exist.

ios-voice

"Contact your technical support representative. Report the configuration and the full text of the error message."

TCMSP-3-TCMSP_HAIRPIN_NOTPOSSIBLE

3-Error

Call can't be hairpinned. cdb 0x[hec] dst_cdb 0x[hec] dst_call_id [dec]

A DSP-less call could not be hairpinned.

ios-voice

"Check the dial-peer configuration."

TCMSP-3-TCMSP_HAIRPIN_FAILED

3-Error

Call hairpinning failed. cdb 0x[hec] dst_cdb 0x[hec] dst_call_id [dec]

A DSP-less call could not be hairpinned.

ios-voice

"Under heavy traffic this failure may happen because no TDM resources wereavailable. Contact your technical support representative include the full text of the error message."

TCMSP-3-TCMSP_CALL_DISC_FAILED

3-Error

TCMSP call disconnect failed. channel id [chars] ret [dec]

TCMSP call disconnect could not be successfully passed and it may result hung calls.

ios-voice

"Contact your technical support representative. Report the configuration and full text of the error message."

DSPFARM-3-ERROR

3-Error

[chars]

Error on DSPFARM module.

-

LOG_STD_SH_TECH_ACTION

DSPFARM-3-ERROR

3-Error

Errors on DSPFARM module [chars]\n

Errors on DSPFARM module

dspfarm

" Check sh dspfarm all"

DSPFARM-4-WARNING

4-Warning

Warning on DSPFARM module [chars]\n

Warning on DSPFARM module

dspfarm

" Check sh dspfarm all"

DSPFARM-4-NOTICE

4-Warning

Failure on DSPFARM module [chars]\n

Failure on DSPFARM module

dspfarm

" Check sh dspfarm"

DSPFARM-4-INFO

4-Warning

Info on DSPFARM module [chars]\n

Info on DSPFARM module

dspfarm

" Check sh dspfarm"

SIP-3-QUEUE_ERROR

3-Error

Unable to enqueue event [chars] [dec] to a process watched queue. Current size: [dec] max size: [dec]

-

-

-

SIP-3-INSV_ERROR

3-Error

Error encountered while trying to bring the SIP component into service

During bootup of the gateway each of the Service Provider Interfaces SPIs are brought into service. The SIP SPI creates several processes

voice-sip

LOG_STD_RECUR_ACTION

SIP-3-LIST_ERROR

3-Error

Unable to create list for [chars]

Failure to create a list generally indicates that the router is out of memory either due to a memory leak or insufficient memory. If the error was generated soon after a reload its more likely that the router doesn't have enough memory. If the router has been running for a while a memory leak is more likely. The SIP component is not properly initialized and SIP calls may not complete properly.

voice-sip

show process memory

SIP-3-INTERNAL

3-Error

[chars]

-

-

-

SIP-3-UNSUPPORTED

3-Error

[chars]

An internal software error has occurred.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-5-TLS_CONNECTION

5-Notice

[chars]

TLS connection is successful or failed

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-STREAM_SERVICE

3-Error

[dec] [chars]

Websocket Connection has failed or closed by Websocket Server.

voice-sip

LOG_STD_SH_TECH_ACTION

CUBE-3-LICENSING

3-Error

[chars]

CUBE Licensing Enforcement

ipipgw

LOG_STD_SH_TECH_ACTION

SIP-3-INVALID

3-Error

Invalid [chars] [dec]

An internal software error has occurred.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-BADPAIR

3-Error

Unexpected [chars] [dec] [chars] in state [dec] [chars] substate [dec] [chars]

The SIP state machine has encountered an error while processing an event or timer.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-6-IGNORE

6-Information

Unexpected [chars] [dec] [chars] in state [dec] [chars] substate [dec] [chars]

The SIP state machine has encountered an error while processing an event or timer.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-CONSTRUCT

3-Error

Error encountered while trying to construct a \[dec] [chars]\ [chars] message

An error was encountered while attempting to construct a SIP request or response message. If malloc errors where also seen then that is most likely the root of the problem. If no memory allocation errors have occurred then this may be an internal problem.

voice-sip

"If there were memory allocation errors at the" "same time as this error then this error can be ignored. Otherwise: " LOG_STD_SH_TECH_ACTION

SIP-3-NORESOURCE

3-Error

No resources for [chars]

An error was encountered while trying to obtain memory resources for an internal queue or table. If malloc errors where also seen then that is most likely the root of the problem. If no memory allocation errors have occurred then this may be an internal problem.

voice-sip

"If there were memory allocation errors at the" "same time as this error then this error can be ignored. Otherwise: " LOG_STD_SH_TECH_ACTION

SIP-3-NOMATCH

3-Error

Unable to find matching CCB for ccCallID [dec]

An internal error was encountered while trying to match a call ID with a call control block

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-5-DIALPEER_STATUS

5-Notice

VoIP dial-Peer <[dec]> is [chars]

VoIP dial-peer's operational status is changed

voice-sip

"If the dial-peer status is busyout the session target configured " "under the dial-peer is not reachable"

SIP-3-DIGITEND

3-Error

Missing digit end event for \'[chars]\' for call ID [chars]

A digit begin event was detected without a matching digit end. This is most likely an internal error which is self correcting the NOTIFY for the digit has been transmitted.

voice-sip

LOG_STD_ACTION

SIP-3-FORKING_CODEC

3-Error

No forking codecs configured for dial-peer [dec] the forked m-lines will be rejected. Forking codecs are [chars]

Media forking requests which arrive in an INVITE message are identified by multiple media lines m-lines in the SDP. Each media line defines a

voice-sip

"Modify the dial-peer configuration to include one " "of the forking codecs listed using either the codec command or the " "voice-class codec command."

SIP-4-MAXSDP

4-Warning

SIP message sent with maximum SDP.

An SIP protocol message containing the maximum allowable SDP size has been sent. If the desired SDP was greater than the maximum size limit the SDP has been truncated at the limit. If the desired SDP was equal to the maximum size limit no truncation has occurred. This warning may indicate that an SIP request containing an unusually large SDP has been received from an external SIP application for a specific call resulting in an SIP response with the maximum SDP.

voice-sip

LOG_STD_NO_ACTION

SIP-3-DIGITQFULL

3-Error

Unable to queue DTMF digit. Queue full. size: [dec]

A request to queue a DTMF digit was rejected because the DTMF queue is full. A 5xx server error has been returned. This error may indicate that a flood of DTMF digit requests from an external SIP application for a specific call has been recieved in a very short period of time.

voice-sip

LOG_STD_NO_ACTION

SIP-3-UNKNOWNOBJ

3-Error

MIB object [chars].[dec] is not known by MIB API subsystem.

The MIB object specified in the SNMP GET PDU has been correctly identified by the SNMP Agent infrastructure but was not correctly identified by the subsystem responsible for the MIB. Processing of the GET operation cannot continue. The SNMP Agent infrastructure and subsystem responsible for the MIB under normal conditions will always be synchronized to the same set of MIB objects that is the same version of the MIB. This condition indicates

voice-sip

LOG_STD_ACTION

SIP-3-NOGETSTRUCT

3-Error

No data structure passed to MIB API subsystem.

The SNMP Agent MIB subsystem for this MIB did not pass any data structure to the MIB API subsystem for the proper retrieval of the requested object data. Processing of the GET operation cannot continue.

voice-sip

LOG_STD_ACTION

SIP-3-NOSETDATA

3-Error

No SET data passed to MIB API subsystem.

The SNMP Agent MIB subsystem for this MIB did not pass any data to the MIB API subsystem for the proper assignment of values to the internal data structures of the object. Processing of the SET operation cannot continue.

voice-sip

LOG_STD_ACTION

SIP-6-LONG_DUR_CALL_DETECTED

6-Information

Long Duration Call is detected [chars]\n

The call is active for configured duration of long call

voice-sip

LOG_STD_ACTION

SIP-3-DIALPEERBWCAC

3-Error

Calling number [chars] called number [chars] dial-peer [dec] used bandwidth [dec] available bandwidth [dec] requested bandwidth [dec] call state [chars]

Bandwidth CAC has rejected the call/media renegotiation due to configured dial-peer bandwidth threshold being exceeded

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-INTBWCAC

3-Error

Calling number [chars] called number [chars] dial-peer [dec] interface [chars] used bandwidth [dec] available bandwidth [dec] requested bandwidth [dec] call state [chars]

Bandwidth CAC has rejected the call/media renegotiation due to configured interface bandwidth threshold being exceeded.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-PTIME

3-Error

Unsupported Ptime value [dec] using minimum Ptime value of [dec] on CallID [dec] Codec=[chars]

Unsupported Ptime value negotiated

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-INTCALLCAC

3-Error

Call rejected due to CAC based on number of calls on the interface sent response [dec]

Interface-calls CAC has rejected the call due to configured int-calls threshold being exceeded.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-TOTCALLCAC

3-Error

Call rejected due to CAC based on Total-calls sent response [dec]

Total-calls CAC has rejected the call due to configured total-calls threshold being exceeded.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-CPUCAC

3-Error

Call rejected due to CAC based on CPU usage sent response [dec]

CPU usage CAC has rejected the call due to configured cpu-avg|cpu-5sec threshold being exceeded.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-MEMCAC

3-Error

Call rejected due to CAC based on Memory usage sent response [dec]

Memory usage CAC has rejected the call due to configured io-mem|proc-mem|total-mem threshold being exceeded.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-3-MAXCONNCAC

3-Error

Call rejected due to CAC based on maximum number of connections on dial-peer [dec] sent response [dec]

Maximum number of connections CAC has rejected the call due to configured max-conn threshold being exceeded.

voice-sip

LOG_STD_SH_TECH_ACTION

SIP-5-EVENT_TRACE_PATH_ERR

5-Notice

Event Trace Dump PATH \[chars]\ not accesible. Verify credentials directory path and network connectivity. Correct the Error and reconfigure Dump-file

Event Trace Dump-file Location not accessible

ipipgw

"Correct the accesibility Error and reconfigure"

SIP-2-SILENT_DISCARD

2-Critical

Silent Discard [chars]

Request received from Untrusted Host.

voice-sip

"Block the request from untrusted host at network layer"

SIP-5-BIND_LINE_STATUS

5-Notice

bind line proto status

Informational message on bind line proto

voice-sip

LOG_STD_NO_ACTION

SIP-4-WEAK_PASSWORD_TYPE

4-Warning

Command has been added to the configuration using a type [dec] password. However type [dec] passwords will soon be deprecated. Migrate to a supported password type [dec]

Password encryption type deprecated. New password type to be used

voice-sip

LOG_STD_ACTION

SIP-3-PASSWORD_REKEY_FAILED

3-Error

Failed to encrypt type 6 password after master key change. Password [chars] will become unusable

Type 6 password encryption failed after master key change

voice-sip

LOG_STD_ACTION

SIP-2-TLS_HANDSHAKE_FAILED

2-Critical

TLS handshake failure - remote_addr=[chars] remote_port=[dec]

TLS handshake failed

voice-sip

LOG_STD_ACTION

SIP-1-LICENSING

1-Alert

[chars]

SIP Service for Eval license status

voice-sip

LOG_STD_ACTION

CUBE-5-LICENSE_INFO

5-Notice

Requested for [dec] [chars] SIP trunk licenses and result is [chars]

Periodic entitlement status

ipipgw

LOG_STD_ACTION

SIP-5-REPORTING

5-Notice

Reported use of [dec] CUBE_T_VGW TDM-SIP sessions

VGW entitlement status

voice-sip

LOG_STD_ACTION

DSMP-6-SESSION_DATABASE_FAILED

6-Information

Cannot create DSMP session database\n

Failed to create DSMP session.

ios-voice

"Check the size of free memory to make sure there is enough memory."

DSMP-3-MSGSNDFAIL

3-Error

channel:[chars] DSP ID:0x[hec] Message ID:0x[hec]

A message could not be sent to the DSP. The session continued but may have experienced problems.

ios-voice

"Contact your technical support \n\ representative include the full text of the error message."

DSMP-3-NOEVENT

3-Error

no free event structure available from [chars] for DSMP message

There were no event structures remaining in the system pools to alert the router of a voice or signaling event.

ios-voice

"Contact your technical support " "representative include the full text of the error message."

DSMP-3-DSPALARM

3-Error

Alarm on DSP [chars]: status=0x[hec] message=0x[hec] text=[chars]

The DSP reported a fatal error. All sessions on the DSP were dropped and a DSP reload was attempted.

ios-voice

"Contact your technical support\n\ representative include the full text of the error message."

DSMP-3-DSP_TIMEOUT

3-Error

DSP timeout on DSP [chars]: event 0x[hec] [chars]

Timeout on DSP response.

ios-voice

"The DSP has been automatically reset. If problem persists contact" "your technical support representative"

DSMP-3-INTERNAL

3-Error

Internal Error : [chars]

DSMP Internal error

ios-voice

"Contact your technical support representative"

DSMP-4-WARNING

4-Warning

Warning : [chars]

Resource temporarily not available

ios-voice

"Contact your technical support representative if condition lasts"

DSMP-3-INVALID_EVENT

3-Error

Unhandled event: current state:[chars] event:[chars]

The event is not handled in the DSMP gateway state machine specification

ios-voice

"Contact your technical support representative"

DSMP-3-SUBSYS_UNINITIALIZED

3-Error

Internal Error : [chars]

DSMP Subsystem not initialized

ios-voice

"Contact your technical support representative"

DSMP-3-PRG_ERROR

3-Error

Programming Error : [chars]

Progaramming error in DSMP subsys

ios-voice

"Contact your technical support representative"

DSMP-3-NOLICENSE

3-Error

[chars]:No License available Tivan Recording could not be Triggered

There are no recording license remaining in the license pool

ios-voice

" Check your configuration for smart license availability"

VOICE_HA-7-STATUS

7-Debug

[chars].

VOICE HA INFRA info/status messages.

voice-ha

"None"

VOICE_HA-1-SELF_STATE_PROTECTED

1-Alert

[chars] RG[[dec]] [chars].

VOICE HA functionality has been disabled in this router due to call checkpointing failure.

voice-ha

" Router need immediate reload."

VOICE_HA-1-INTERFACE_DOWN

1-Alert

[chars] RG[[dec]] [chars].

Interface went down

voice-ha

-

VOICE_HA-5-PEER_STATE_READY

5-Notice

[chars] RG[[dec]] VOICE HA Peer exiting from PROTECTED state.

VOICE HA functionality is enabled on peer.

voice-ha

-

VOICE_HA-5-PEER_STATE_PROTECTED

5-Notice

[chars] RG[[dec]]. HA functionality disabled for Voice.

VOICE HA functionality is disabled on the peer. due to call checkpointing failure.

voice-ha

"Peer Router need immediate reload."

VOICE_HA-2-BULK_SYNC_ERR

2-Critical

[chars].

VOICE HA INFRA encountered a bulk-sync error.

voice-ha

"Collect requested data/traceback and forward to the " "voice-ha component."

VOICE_HA-2-SYM_DATA_COLLECT_ERR

2-Critical

UC-INFRA HA module [chars] reported DATA COLLECT failure CID:[dec] with error code [dec].

Specified HA module reported error during call leg data collection.

-

"Collect requested data/traceback and forward to the " "appropriate DDTS-component/module owner " "of the specified HA module for investigation."

VOICE_HA-3-DATA_COLLECT_ERR

3-Error

[chars]: HA Module [chars] reported DATA COLLECT failure mainst ID:[dec] CID:[dec].

Specified HA module reported error during call leg data collection.

-

"Collect requested data and forward to the " "appropriate DDTS-component/module owner " "of the specified HA module for investigation."

VOICE_HA-2-SYM_DATA_RECREATE_ERR

2-Critical

UC-INFRA HA module [chars] reported RECREATE failure CID:[dec] with error code [dec].

Specified HA module reported error during call leg re-create.

-

"Collect requested data/traceback and forward to the " "appropriate DDTS-component/module owner " "of the specified HA module for investigation."

VOICE_HA-3-DATA_RECREATE_ERR

3-Error

[chars]: HA Module [chars] reported [chars] RECREATE failure mainst ID:[dec] CID:[dec].

Specified HA module reported error during call leg re-create.

-

"Collect requested data and forward to the " "appropriate DDTS-component/module owner " "of the specified HA module for investigation."

VOICE_HA-2-SWITCHOVER_IND

2-Critical

[chars].

VOICE HA detected a failover transition on the STANDBY to become the new ACTIVE.

voice-ha

"Verify calls on the new ACTIVE. " "Peer needs to be in STANDBY mode " "before the next failover."

VOIPFIB-3-NOMEM

3-Error

[chars] [dec] [dec]

An internal software error occurred.

voip_fib

LOG_STD_SH_TECH_ACTION

VOIPFIB-3-BADIDB

3-Error

Invalid IDB: Slot [dec] Channel [dec]

An internal software error occurred.

voip_fib

LOG_STD_SH_TECH_ACTION

VOIPFIB-3-NODSPINFO

3-Error

Failed to get DSP info

An internal software error occurred.

voip_fib

LOG_STD_SH_TECH_ACTION

VOIPFIB-3-INVALIDSESSION

3-Error

Invalid VoIP Session

An internal software error occurred.

voip_fib

LOG_STD_SH_TECH_ACTION

VOIPFIB-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

voip_fib

LOG_STD_ACTION

IVR-3-BAD_IVR_VERSION

3-Error

Script requires version [dec].[dec] image supports [dec].[dec]\n

IVR Script requires a higher IVR infrastructure version

voice-ivr

"Upgrade IOS or use a different script"

IVR-3-NOSCRIPT

3-Error

Could not load IVR script\n [chars]\n errno=[dec]=[chars]

Could not read in the IVR script

voice-ivr

"Check that script exists on the server and is readable."

IVR-3-BADSCRIPT

3-Error

Could not parse malformed IVR script: [chars]\n

Could not parse malformed IVR script

voice-ivr

"Check the script and fix the syntax error."

IVR-3-ABNORMAL_EXIT

3-Error

TCL IVR Process for this call with CallID [dec] exits bad event: [chars] received\n

The TCL IVR call process exited for the specified call. The call \n\ process did not clear a prior call properly so other events could \n\ not be handled. Only the specified call is affected

voice-ivr

"If problem persists for subsequent callscopy the message exactly \n\ as it appears on the console or in the system log contact your \n\ Cisco technical support representative and provide the representative \n\ with the gathered information."

IVR-3-LOW_MEMORY

3-Error

IVR: Sytem running on low memory. Free memory: %l bytes. Call is rejected.\n

System does not have enough CPU resources available to accept\n\ a new call

voice-ivr

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway."

IVR-2-APP_CRIT_R

2-Critical

[chars]\n

A critical message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-3-APP_ERR_R

3-Error

[chars]\n

An error message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-4-APP_WARN_R

4-Warning

[chars]\n

A warning message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-6-APP_INFO_R

6-Information

[chars]\n

An informational message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-6-APP_PARALLEL

6-Information

Cannot use dial-peer [dec] parallel hunt-group for a rotary or

The dial-peer for parallel hunt-groups must have a unique pilot number.

voice-ivr

"Create a unique dial-peer destination-number for the parallel \n\ hunt-group."

IVR-6-APP_SEQ_HUNT

6-Information

Pilot hunt-group '[chars]' found in hunt-group list. Nested hunt-groups are allowed only as the hunt-group's final number.\n

Nested sequential hunt-group detected in dial-peer rotary. \n\ Nested hunt-groups is unsupported.

voice-ivr

"Do not create hunt-group lists that contain hunt-group pilot numbers."

IVR-1-APP_PARALLEL_INVALID_LIST

1-Alert

Call terminated. Huntgroup '[dec]' does not contain enough valid SIP end-points to proceed with a parallel call. \n

The call to a parallel hunt-group was denied because less than \n\ two valid SIP end-points were found in the huntgroup list.

voice-ivr

"Check the hunt-group list's numbers. Remove any incorrect numbers \n\ or numbers that have a non-SIP dial-peer. If the numbers are from\n\ SIP phones then verify whether the phones have registered to the\n\ system yet."

IVR-2-INVALID_DSAPP_DIALPEER

2-Critical

Service dsapp contains an invalid dial peer tag: [chars]

An invalid dial peer tag has been configured for the dsapp service. The tag either is not in the range from 1 to 2147483647 or it belongs to a non-existent dial-peer.

voice-ivr

"Enter the <CmdBold>show running-config<NoCmdBold> " "or the <CmdBold>show dial-peer voice<NoCmdBold> " "command to find a valid dial peer tag. " "Reconfigure the dial peer with a valid tag or " "remove the dial peer tag completely to allow the " "system to match from the system dial peers."

IVR-4-INVALID_DSAPP_BLINDTIME

4-Warning

Blind-xfer-wait-time [dec] is invalid. Resetting to [dec] seconds.

The configured value for blind-xfer-wait-time was outside of the acceptable range 0-10 and has been reset to

voice-ivr

"If the new value for blind-xfer-wait-time is " "unacceptable you can change it from the command " " line interface."

IVR-4-INVALID_DSAPP_TOGGLE_TIME

4-Warning

Disc-toggle-time [dec] is invalid. Resetting to [dec] seconds.

The configured value for disc-toggle-time was outside of the acceptable range 10-30 and has been reset

voice-ivr

"If the new value for disc-toggle-time " "is unacceptable you can change it from the " "command line interface."

IVR-5-APP_CALL_PREEMPTION

5-Notice

CallID [dec] is being preempted\n

A notification message was reported by an IVR application on detecting callID [dec] being preempted.

voice-ivr

"This is not a problem but notifying syslog about preempted call."

IVR-2-APP_CRIT

2-Critical

[chars]\n

A critical message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-3-APP_ERR

3-Error

[chars]\n

An error message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-4-APP_WARN

4-Warning

[chars]\n

A warning message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-6-APP_INFO

6-Information

[chars]\n

An informational message was reported by an IVR Tcl application.

voice-scripts

"The remedy of the problem is application specific."

IVR-5-APP_MED_INACT_DETECTED

5-Notice

[chars]\n

A notification message was reported by an IVR application on detecting media inactivity.

voice-scripts

"This is not a problem but notifying syslog about media inactivity."

IVR-5-APP_MED_REACT_DETECTED

5-Notice

[chars]\n

A notification message was reported by an IVR application on detecting media activity.

voice-scripts

"This is not a problem but notifying syslog about media activity."

IVR-5-APP_LOG_DUR_CALL_DETECTED

5-Notice

[chars]\n

System does not have enough CPU capacity to spawn a new instance of \n\ IVR application

voice-ivr

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway."

IVR_MSB-3-NOPROMPT

3-Error

Could not create IVR prompt\n [chars]\n errno=[dec]=[chars]

Could not read in the IVR prompt

voice-ivr

"Check that prompt exists on the server and is readable."

IVR_MSB-3-NO_IO_MEMORY

3-Error

[chars]: Failed to create pool_group [hec] buffer_pool [hec] platform_mc_buf_pool_count [dec]\n

No IO memory to create IVR private pak pool

voice-ivr

"Check to see if there is enough IO memory."

IVR_MSB-3-INVALID_MAX_PROMPTS

3-Error

[chars]: This version of IOS does not support prompt playout for IVR applications.\n

This error will be displayed if an IVR application is used on a gateway that does\n\ not support IVR prompt playout.

voice-ivr

"Ensure that this platform and IOS version support the IVR feature set."

IVR_MSB-3-INVALID_PROMPT_SIZE

3-Error

[chars]: Bad size for the prompt file [chars]. Read size [dec]. Expected size [dec].\n

Prompt file size error. File may be corrupted.

voice-ivr

"Replace the bad prompt file."

DNLD-3-ERROR

3-Error

[chars]

Error on DNLD module.

-

LOG_STD_SH_TECH_ACTION

DNLD-6-DSPFARM_REGISTER_FAILED

6-Information

Failed to register DNLD Application with DSPFARM\n

Failed to register DNLD Application with DSPFARM.

-

LOG_STD_SH_TECH_ACTION

TSP-3-NOEVENT

3-Error

no free event structure available from [chars] for DSP message

There were no event structures remaining in the system pools to alert the router of a voice or signaling event.

-

"Check that the voice port for which the event was reported is " "still operational. If not clear the voice port."

TSP-3-CAPABILITYMISMATCH

3-Error

voice port [chars]: call connection id [0x[hec] 0x[hec] 0x[hec] 0x[hec]]

There was a capabilities mismatch between the two call legs. capabilities are negotiated between call legs for CODEC VAD and FAX rate.

-

"Check that the dial peer configuration is appropriate for the interface " "in question. Also check that and configuration on the interface is " "correct."

TSP-3-DSPALARM

3-Error

voice port [chars]: status=0x[hec] message=0x[hec]

The DSP reported a fatal error. All calls on the DSP were dropped and a DSP reload was attempted.

-

"Verify that the DSP reloaded properly by attempting to place a call " "on the affected voice port. Contact your technical support " "representative include the full text of the error message."

TSP-5-PRI

5-Notice

[chars] at slot [dec] unit [dec] channel [dec]

A PRI signalling channel is added/deleted to TSP's inventory of signalling channels.

-

"This is a notification message only. " "No action is required."

TSP-3-FSM_ERROR

3-Error

[chars]

Internal Finite State Machine Error.

-

"Contact your technical support representative include the full text of\n\ the error message."

VOIP_RTP-6-MEDIA_LOOP

6-Information

[chars]\n

-

voice-rtp

"Please check your configuration."

VOIP_RTP-3-DSCPVIOLATION

3-Error

[chars]

-

voice-rtp

"Please check your configuration."

VOIP_RTP-3-MEDIABWVIOLATION

3-Error

[chars]

-

voice-rtp

"Please check your configuration."

VOIP_RTP-4-VQM_HALT_ALL

4-Warning

System one-minute CPU has reached [dec]%% - Video quality monitoring is halted for all calls.

Because system one-minute CPU usage has reached a high percentage DSPFarm video quality monitoring service is disabled for all calls which includes on-going calls that were being monitored as well as new calls that are configured to be monitored.

cube-vqm

"Check the system CPU and find out the cause of the " "high CPU. Video quality monitoring service should " "not have a significant impact on CPU usage."

VOIP_RTP-4-VQM_HALT_NEW

4-Warning

System one-minute CPU has reached [dec]%% - Video quality monitoring is not enabled for new calls.

Because system one-minute CPU usage has reached a high percentage DSPFarm video quality monitoring service is disabled for new calls that are configured to be monitored. Existing calls that are already monitored are not impacted.

cube-vqm

"Check the system CPU and find out the cause of the " "high CPU. Video quality monitoring service should " "not have a significant impact on CPU usage."

VOIP_RTP-5-VQM_RESUME

5-Notice

System one-minute CPU is lowered to [dec]%% - Resuming video quality monitoring for all calls.

Because system one-minute CPU usage has decreased from a high percentage DSPFarm video quality monitoring service is enabled again for all calls which includes on-going calls whose monitoring was halted as well as new calls that are configured to be monitored.

cube-vqm

"N/A. This message is purely informational."

DIALPEER_DB-3-ADDPEER_MEM_THRESHOLD

3-Error

Addition of dial-peers limited by available memory\n

The available memory does not permit the addition of more dial-peers.

ios-voice

"Increase the processor memory in order to be able to add more\n\ dialpeers."

DIALPEER_DB-6-ADDPEER_WARNING

6-Information

Addition of too many dial-peers may affect performance\n

The number of dial-peers is high. This will have an effect on the\n\ dial-peer lookup time resulting in longer call setup time.

ios-voice

"Use the minimum number of dial-peers necessary for your numbering plan."

DIALPEER_DB-3-ADDPEER_PLATFORM_LIMIT

3-Error

Addition of dial-peers limited by platform\n

This platform does not permit the addition of more dial-peers.

ios-voice

"Reduce the number of dial-peers in your numbering plan."

DIALPEER_DB-3-NOMAP

3-Error

Could not load dnis-map [chars]\n url=[chars]\n errno=[dec]=[chars]

Could not read in the dnis-map

ios-voice

"Check that map exists on the server and is readable."

DIALPEER_DB-3-DP_MALLOC_FAIL

3-Error

Could not allocate memory in [chars] for tag [dec]\n

Ran out of memory

voice-dialpeer

"Observe why memory is exhausted"

DIALPEER_DB-6-FB_ENTRY_NOT_CREATED

6-Information

Could not create probe for tag [dec]\n

Fallback cache full

voice-dialpeer

"Increase Fallaback cache size"

DIALPEER_DB-3-DIALPEER_ACCOUNTING

3-Error

Connections for dial-peer [dec] is negative. Resetting connections to 0.\n

Active Connections for dial-peer is negative.

ios-voice

"Verify if dial-peers were removed with active calls associated to them\n\ and added back while the calls were still connected."

DIALPEER_DB-3-NODEPMAP

3-Error

Could not load e164-pattern-map [dec]\n url=[chars]\n errno=[dec]=[chars]

Could not read in the e164-pattern-map

voice-dialpeer

"Check that map exists on the server and is readable."

DIALPEER_DB-3-NOE164TRANSURL

3-Error

Could not load e164-translation [dec]\n url=[chars]\n error=[chars][dec]

Could not get the voice class e164-translation url data file

voice-dialpeer

"Check that url data file exists on the server and is readable."

VOICE_UTIL-3-NORAWMSG

3-Error

no free raw msg structure available from [chars] for signaling message

There were no rawmsg structures remaining in the system pools to alert the\n\ router of a voice or signaling event.

ios-voice

"Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port."

VOICE_IEC-3-GW

3-Error

[chars]: Internal Error [chars]: IEC=[dec].[dec].[dec].[dec].[dec].[dec] on callID [dec] [chars]

An internally-detected error has caused a voice call to be released or terminated. An Internal Error Code IEC has been

ios-voice

"Refer to the IEC Error Message Decoder at " "http://www.cisco.com/univercd/cc/td/doc/product/voice/vtgemd.htm " "and enter the IEC or enter the <CmdBold>show voice iec " "description<NoCmdBold> <CmdArg>IECvalue<NoCmdArg> command with " "<CmdArg>IECvalue<NoCmdArg> being the value of the IEC that was " "received for more information on the details of this error. It " "is possible some debugging actions might also indicate the cause " "of the error."

VOICE_IEC-3-GK

3-Error

[chars]: Internal Error [chars]: IEC=[dec].[dec].[dec].[dec].[dec].[dec] on \n GUID [chars] \n confid [chars]

An internally-detected error has caused a voice call to be released or terminated. An Internal Error Code IEC has been

voice-h323

"Refer to the IEC Error Message Decoder at " "http://www.cisco.com/univercd/cc/td/doc/product/voice/vtgemd.htm " "and enter the IEC or enter the <CmdBold>show voice iec " "description<NoCmdBold> <CmdArg>IECvalue<NoCmdArg> command with " "<CmdArg>IECvalue<NoCmdArg> being the value of the IEC that was " "received for more information on the details of this error. It " "is possible some debugging actions might also indicate the cause " "of the error."

VOICE_IEC-3-EXT

3-Error

Externally-generated Internal Error Code received: [dec].[dec].[dec].[dec].[dec].[dec]

Some external entity has initiated the termination of a voice call. It has signalled its Internal Error Code to this gateway to be reported in the accounting record for this call. In addition it is being reported through syslog because of the <CmdBold>voice iec syslog<NoCmdBold> configuration.

ios-voice

"Refer to the IEC Error Message Decoder at " "http://www.cisco.com/univercd/cc/td/doc/product/voice/vtgemd.htm " "and enter the IEC or enter the <CmdBold>show voice iec " "description<NoCmdBold> <CmdArg>IECvalue<NoCmdArg> command with " "<CmdArg>IECvalue<NoCmdArg> being the value of the IEC that was " "received for more information on the details of this error. It " "is possible some debugging actions might also indicate the cause " "of the error."

GSMAMRNB_ENABLER-3-GSMAMRNB_LICENSE_EULA_NOT_ACCEPTED

3-Error

\n********************************************************* \ \nWARNING: GSM AMR-NB License is not yet activated. \ \nPlease configure 'license feature gsmamrnb-codec-pack'\ \nand accept the EULA to activate the license. \ \n*********************************************************\n

EULA is not accepted for the license

ios-licensing-atg

LOG_STD_ACTION

VOICE_ELOG-3-DUMPFAIL

3-Error

Could not dump to remote file - [chars] [chars]. Error=[dec][chars]

Fail to dump event log to the remote file

ios-voice

"Check network connectivity setup and configuration of the protocol"

VOICE_ELOG-3-INIT_FAIL

3-Error

Initialization fails - [chars].

Fail to initialize event logger system

ios-voice

"Check availability of router resource such as memory"

VOICE_ELOG-3-MSGDROPPED

3-Error

[dec] messages failed to be written in event log client id:[chars] dump url:[chars].

Failed to save event message to the log

ios-voice

"Check availability of system memory and " "error for dumping event log if configured"

VOICE_ELOG-4-MEM_USAGE_HI_WATERMARK

4-Warning

System memory on high usage [dec]/100. Stopping processing

System is low on memory so throttle control is applied on\n\ event logger system and it will turn on again when remaining\n\ memory is above high water mark

ios-voice

"Ensure that the gateway has the recommended amount of memory for\n\ this IOS feature set and version or scale down usage such as disabling FTP\n\ dump enable event log only for specific application etc."

VOICE_ELOG-5-MEM_USAGE_LO_WATERMARK

5-Notice

System memory usage [dec]/100 is below low watermark now.

System memory is back high so throttle control is removed.

ios-voice

""

VOICE_FILE_ACCT-3-DUMPFAIL

3-Error

Could not dump to remote file - [chars] [chars]. Error=[dec][chars]

Fail to dump event log to the remote file

ios-voice

"Check network connectivity setup and configuration of the protocol"

VOICE_FILE_ACCT-3-INIT_FAIL

3-Error

Initialization fails - [chars].

Fail to initialize event logger system

ios-voice

"Check availability of router resource such as memory"

VOICE_FILE_ACCT-1-ALLMODE_FAIL

1-Alert

All modes of file accounting have failed - [chars].

All modes of file accounting failed need to fixed right away in order to not to lose accounting information

ios-voice

"Fix the link issues any for ftp link/flash issues then reset file accounting using file-acct reset"

VOICE_FILE_ACCT-3-MSGDROPPED

3-Error

[dec] messages failed to be written in event log client id:[chars] dump url:[chars].

Failed to save event message to the log

ios-voice

"Check availability of system memory and " "error for dumping event log if configured"

VOICE_FILE_ACCT-4-MEM_USAGE_HI_WATERMARK

4-Warning

System memory on high usage [dec]/100. Stopping processing

System is low on memory so throttle control is applied on\n\ event logger system and it will turn on again when remaining\n\ memory is above high water mark

ios-voice

"Ensure that the gateway has the recommended amount of memory for\n\ this IOS feature set and version or scale down usage such as disabling FTP\n\ dump enable event log only for specific application etc."

VOICE_FILE_ACCT-5-MEM_USAGE_LO_WATERMARK

5-Notice

System memory usage [dec]/100 is below low watermark now.

System memory is back high so throttle control is removed.

ios-voice

""

SKINNYSECURESERVICE-3-NOINIT

3-Error

Can't initialize Secure Skinny server

Internal problems with initializing ports for the Secure Skinny server

ios-callmgr

"Make sure the Skinny secure server port is available on the local machine."

SKINNYSECURESERVICE-3-NOMEM

3-Error

Can't initialize memory for Secure Skinny server

Insufficient Memory for Secure Skinny server

ios-callmgr

"Increase amount of available memory"

SKINNYSECURESERVICE-3-NOSOCKETS

3-Error

Max Number of Skinny Secure Server sockets exceeded: too many IP phones

There are too many skinny Secure server clients requesting service

ios-callmgr

"Reduce number of Secure IP phones requesting service"

SKINNYSECURESERVICE-3-NOPROC

3-Error

Could not start Skinny Secure Server

Internal Problem in process creation

ios-callmgr

"None"

SKINNYSECURESERVICE-6-TLS_EVAL_LIMIT

6-Information

The TLS signaling tunnels usage exceeds the license limit.

The TLS signal tunnels usage exceeds the license limit.

xformers-csl

"Please install the Permanent license"

SKINNYSECURESERVICE-6-TLS_EVAL_FREE_ERROR

6-Information

Error encountered on release TLS signaling tunnels.

Error encountered on release TLS signaling tunnels.

xformers-csl

"Please install the Permanent license"

SKINNYSERVER-3-NOINIT

3-Error

Can't initialize Skinny server

Internal problems with initializing ports for the Skinny server

ios-callmgr

"Make sure the Skinny server port is available on the local machine."

SKINNYSERVER-3-NOMEM

3-Error

Can't initialize memory for Skinny server

Insufficient Memory for Skinny server

ios-callmgr

"Increase amount of available memory"

SKINNYSERVER-3-NOSOCKETS

3-Error

Max Number of Skinny Server sockets exceeded: too many IP phones

There are too many skinny server clients requesting service

ios-callmgr

"Reduce number of IP phones requesting service"

SKINNYMAIN-4-KEYPADFAST

4-Warning

Keypad messages from the phone [dec] are too fast

The inter digit interval is too short. Each digit may not be processed properly

cme-callcontrol

"Please configure keypad-normalize for the phone"

CTLPROVIDERSERV-3-NOINIT

3-Error

Can't initialize Credentials server

Internal problems with initializing ports for the Credentials server

ios-callmgr

"Make sure the Credentials server port is available on the local machine."

CTLPROVIDERSERV-3-NOMEM

3-Error

Can't initialize memory for Credentials server

Insufficient Memory for Credentials server

ios-callmgr

"Increase amount of available memory"

CTLPROVIDERSERV-3-NOSOCKETS

3-Error

Max Number of Credentials Server sockets exceeded

There are too many Credentials clients requesting service

ios-callmgr

"Reduce number of Credentials requesting service"

CTLPROVIDERSERV-3-NOPROC

3-Error

Could not start Credentials Server

Internal Problem in process creation

ios-callmgr

"None"

EXTASSIGNER-3-NOCB

3-Error

\ Failed to find the skinnyCB\n

-

-

-

EXTASSIGNER-3-NOACTPHONE

3-Error

\ Failed to find the calling phone\n

-

-

-

EXTASSIGNER-3-NOMEM

3-Error

\ Failed to malloc\n

-

-

-

EXTASSIGNER-3-ERRTAG

3-Error

\ Invalid tag[dec]\n

-

-

-

EXTASSIGNER-3-NULLPTR

3-Error

\ Null pointer [chars]:[dec]\n

-

-

-

EXTASSIGNER-3-ERRSYNC

3-Error

\ Failed to sync tag[dec] to standby CME\n

-

-

-

EXTASSIGNER-3-ERRSYNC2

3-Error

\ Failed to sync re-assign tag [dec] for [dec] to standby CME\n

-

-

-

EXTASSIGNER-6-ASSIGNED

6-Information

\ Extension assignment successful for phone:SEP[chars]. New pool[dec]. \

Successfully assigned the pool

-

LOG_STD_NO_ACTION

EXTASSIGNER-6-UNASSIGNED

6-Information

\ Extension unassignment successful for phone:SEP[chars]. \ Unassigned pool[dec].\n

Successfully unassigned the pool

-

LOG_STD_NO_ACTION

IRECAGENTSERVER-3-NOINIT

3-Error

Can't initialize iREC agent server

Internal problems with initializing ports for the iREC agent\n\server

ios-callmgr

"Make sure the iREC agent server port is available on the local\n\machine."

IRECAGENTSERVER-3-NOMEM

3-Error

Can't initialize memory for iREC agent server

Insufficient Memory for iREC agent server

ios-callmgr

"Increase amount of available memory"

IRECAGENTSERVER-3-NOSOCKETS

3-Error

Max Number of iREC agent Server sockets exceeded

There are too many iREC agent clients requesting service

ios-callmgr

"Reduce number of iREC agent requesting service"

IRECAGENTSERVER-3-NOPROC

3-Error

Could not start iREC agent Server

Internal Problem in process creation

ios-callmgr

"None"

EDSP-6-VEC_CHANGE

6-Information

EDSP0's LES switching vector set to [chars]

To monitor CEF initialization for the hidden interface.

cme-ephone

LOG_STD_NO_ACTION

EDSP-6-CEF_WAIT

6-Information

Waiting for CEF initialization to complete first ... [dec]

Initialization of CEF RTP sending relies on system's CEF readiness.

cme-ephone

LOG_STD_NO_ACTION

EDSP-4-CEF_TOOLONG

4-Warning

CEF to SCCP devices may be disabled! See message below.

Given up waiting for CEF initialization to complete.

cme-ephone

"Check the message about CEF and the EDSP0 interface below. If the" " vector is EVENTUALLY set to Null CEF RTP sending for SCCP devices is" " disabled. You may try to recover by restarting \"ip cef\" in IOS" " configuration."

EDSP-6-IPV6_ENABLED

6-Information

IPv6 on interface [chars] added.

IPv6 capability has been enabled for the sub-interface.

cme-ephone

LOG_STD_NO_ACTION

EDSP-6-IPV6_FAILED

6-Information

IPv6 on interface [chars] failed.

IPv6 initialization has failed for the sub-interface.

cme-ephone

"Please check IPv6 and interface related configurations."

HUNTGRP-3-INVALID_URL

3-Error

Could not open the file provided in URL: <[chars]>

URL path provided can't be accessed. This usually indicates\n\ that path provided is invalid but may also be because the the\n\ path doesn't allow anonymous access to create files or open it\n\ in write mode

cme-callcontrol

"Check that the url path provided is valid"

HUNTGRP-3-WRITE_FAIL

3-Error

Could not write data to the URL: <[chars]>\n\t %%bytes written=[dec] out of [dec]

Write attempt to the url path provided was unsuccessful. This usually \n\ indicates that the file was successfully opened with write and append \n\ permissions but writing all the content from buffer or may be some of \n\ it to the file failed.

cme-callcontrol

""

CMEXML-3-ERREXEC

3-Error

\ CME XML Client Request Failed at [dec] request [chars]\n

-

-

-

CMEXML-3-ABORTEXEC

3-Error

\ CME XML Client Request Aborted request [chars]\n

-

-

-

CMEXML-6-STARTEXEC

6-Information

\ CME XML Client Request Start request [chars]\n

-

-

-

CCH323-3-CANNOT_ALLOCATE_GW

3-Error

[chars]: cannot allocate gateway structure

Allocation of the CCH323 gateway instance failed. This is possibly due\n\ to the fact that system memory pool is exhausted.

voice-h323

"This can be a catastrophic error"

CCH323-3-CANNOT_CREATE_CCB

3-Error

[chars]: cannot create the H.323 ccb Tree

Creation of the H.323 CCB Tree failed. This is possibly due to the fact \n\ that system memory pool is exhausted.

voice-h323

"This can be a catastrophic error"

CCH323-3-CANNOT_ALLOCATE_CCB

3-Error

[chars]: cannot allocate call control block

Allocation of the CCH323 call control block failed. This is possibly due\n\ to the fact that system memory pool is exhausted.

ios-voice

"This can be a catastrophic error"

CCH323-3-CANNOT_ALLOCATE_CALL_INFO

3-Error

[chars]: cannot allocate call info data structure

Allocation of the CCH323 call info structure failed. This is possibly due\n\ to the fact that system memory pool is exhausted.

ios-voice

"This call will be terminated due to lack of resource"

CCH323-3-CANNOT_INSERT_CCB

3-Error

[chars]: cannot insert control block 0x[hec] to tree

Insertion of this CCH323 call control block to the RBTree failed. This\n\ can be related to a corrupted RBTree

ios-voice

"This can be a catastrophic error"

CCH323-3-CANNOT_FIND_CCB

3-Error

[chars]: cannot find CCH323 call control block based on callID [dec]

Cannot find a CCH323 call control block based on the specified callID

ios-voice

"No action is required. This is an indication that some events happen\n\ out of sequence"

CCH323-3-CCAPI_DISCONNECT_ERROR

3-Error

[chars]: cc_api_call_disconnected returns [dec]

An error is returned when CCH323 attempts to call cc_api_call_disconnected

ios-voice

"None"

CCH323-3-CCAPI_CONNECT_ERROR

3-Error

[chars]: cc_api_call_disconnected returns [dec]

An error is returned when CCH323 attempts to call cc_api_call_connected

ios-voice

"None"

CCH323-3-CANNOT_CREATE_CRVHASH_TBL

3-Error

[chars]: cannot create the H.323 crv hash table

Creation of the H.323 CRV Hash Table failed. This is possibly due to \n\ the fact that system memory pool is exhausted.

voice-h323

"This can be a catastrophic error"

CCH323-3-BAD_IP_ADDRESS

3-Error

[chars]: illegal destination [chars]

The IP address passed from CCAPI in the call setup request is invalid

ios-voice

"Check the dial-peer configuration for the dial-peer that matches the\n\ called party number. Make sure that the session target field contains\n\ valid IP address. or DNS name"

CCH323-3-CALL_SETUP_FAILED

3-Error

[chars]: call setup failed

The call setup request failed

ios-voice

"Verify that the remote destination identified by the IP address is reachable"

CCH323-3-OSS_INIT_FAILED

3-Error

[chars]: OSS init failure: errno = [dec]

OSS ASN1 initialization failed

ios-voice

"This can be catastrophic"

CCH323-3-H225_SM_INIT_FAILED

3-Error

[chars]: H.225.0 State Machine integrity check failed for state [chars]

H.225 State Machine integrity check failed

ios-voice

"This can be catastrophic"

CCH323-3-H225_LIBRARY_INIT_FAILED

3-Error

[chars]: H.225.0 library initialization failed

H.225.0 library initialization failed

ios-voice

"This can be catastrophic"

CCH323-3-CCH323_UNKNOWN_EVENT

3-Error

unknown event [hec]

Unknown CCH323 Event

ios-voice

"No action is required"

CCH323-3-CCH323_RSCMON_SETUP_FAILURE

3-Error

[chars][dec]

A failure was encountered in setting up the monitoring of\n\ H323 resources.

ios-voice

"Try power cycling the system. " LOG_STD_RECUR_ACTION

CCH323-3-STRCALLHISFAIL

3-Error

\ncch323_store_call_history: [chars]

Insert an active H323 call record into call history list failed

ios-voice

"No action is required"

CCH323-2-GTWY_UNREGSTR

2-Critical

Gateway [chars] unregistered from Gatekeeper [chars]

Gateway unregistered from the Gatekeeper

ios-voice

"Verify whether this is user intended or otherwise report this to the\n\ technical support representative."

CCH323-2-GTKP_UNREGSTR

2-Critical

Gatekeeper [chars] requested unregister from Gateway [chars]

Gatekeeper requested unregister from Gateway

ios-voice

"Verify whether this is user intended or otherwise report this to the\n\ technical support representative."

CCH323-6-REGSTR

6-Information

Gateway [chars] registered with Gatekeeper [chars]

Gateway registered with the Gatekeeper

none

"no action is required"

CCH323-2-GTWY_REGSTR_FAILED

2-Critical

Gateway [chars] failed to register with Gatekeeper [chars] even after [dec] retries

Gateway failed to register with Gatekeeper

ios-voice

"Report this immediately to the technical support representative."

CCH323-2-GTWY_REGSTR_FAILED_ALT_GK

2-Critical

Gateway [chars] failed attempt to register with Alternate Gatekeeper [chars]

Gateway failed attempt to register with Alternate Gatekeeper

ios-voice

"Report this immediately to the technical support representative."

CCH323-2-E164_LENGTH_IS_NOT_SUPPORTED

2-Critical

[chars]: E164 address length [dec] is not supported

Received E164 address with the length that is not supported.

ios-voice

"Report this immediately to the technical support representative."

CCH323-3-CCH323_MALLOC_FAILED

3-Error

[chars]: cannot allocate message buffer

Allocation of the CCH323 message buffer failed. This is possibly due\n\ to the fact that system memory pool is exhausted.

ios-voice

"This can be a catastrophic error"

CCH323-3-INTERNAL_EVENT_QUEUE_INIT_FAILED

3-Error

[chars]: Internal event queue initialization failed

Errors are found during initialization of internal event qeuue machanisa

ios-voice

"This can be a catastrophic error"

CCH323-3-POSSIBLE_INTERNAL_EVENT_LOOP

3-Error

[chars]: Exceeding limit on servicing internal event for the same call

The maximum limit on servicing internal event queue has exceeded\n\ the limit. The condition may be caused by internal loops on\n\ sending events between state machines.

ios-voice

"This can be a severe error"

CCH323-3-MAXIMUM_INTERNAL_EVENT_BUFFERS_EXCEED

3-Error

[chars]: Exceeding limit on allocating internal event buffers

The limit for allocating internal event buffers has been exceeded.\n\ The condition may be caused by internal loops on\n\ sending events between state machines.

-

"This can be a severe error"

CCH323-3-CCH323_H225_SEND_EVENT_FAILED

3-Error

[chars]: create send internal event [chars] to H.225 state machine failed

create and send event to H.225 state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers

ios-voice

"This can be a catastrophic error"

CCH323-3-CCH323_H245_SEND_EVENT_FAILED

3-Error

[chars]: create and send event [chars] to H.245 state machine failed

create and send event to H.245 state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers

ios-voice

"This can be a catastrophic error"

CCH323-3-CCH323_RAS_SEND_EVENT_FAILED

3-Error

[chars]: create and send event [chars] to RAS state machine failed

create and send event to RAS state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers

ios-voice

"This can be a catastrophic error"

CCH323-6-LONG_DUR_CALL_DETECTED

6-Information

Long Duration Call is detected [chars]\n

The call is active for configured duration of long call

ios-voice

LOG_STD_ACTION

CCH323-6-CALL_PRESERVED

6-Information

[chars]: H.323 call preserved due to socket closure or error Call Id = [dec] fd = [dec]

An H.225.0 or H.245 socket was closed due to a TCP FIN received from the remote endpoint or a socket error. Calls using these sockets for which call preservation was configured will be preserved. This is not an error but call preservation can occasionally cause hung calls.

voice-h323

"Use \"show h323 calls preserved\" command to get a " "list of all active preserved calls. Long duration preserved calls can " "then be cleared using \"clear call voice\" command."

VOIPAAA-5-VOIP_FEAT_HISTORY

5-Notice

\[chars]

Call feature detail output is used in feature accounting. \n\ This captures multiple feature invokations on a given legthis\n\ can be used for accounting

-

""

VOIPAAA-5-VOIP_CALL_HISTORY

5-Notice

\CallLegType [dec] \ConnectionId [hec][hec][hec][hec] \SetupTime [chars] \PeerAddress %*s \PeerSubAddress %*s \DisconnectCause %*s \DisconnectText %*s \ConnectTime [chars] \DisconnectTime [chars] \CallOrigin %ld \ChargedUnits [dec] \InfoType %ld \TransmitPackets [dec] \TransmitBytes [dec] \ReceivePackets [dec] \ReceiveBytes [dec]

Call history detail output is used in simple accounting. The ASCII comma\n\ delimited output can be stored using syslogd and passed on to other\n\ billing and/or processing software on a server.

-

""

VOIPAAA-3-LOW_CPU_RESOURCE

3-Error

VOIPAAA: System running on high cpu usage.\n\ Accounting for callID=[dec] is rejected.\n

The system does not have sufficient CPU resources\n\ to accept a new call. Any further VoIP AAA requests\n\ will be rejected

voice-aaa

"Ensure that the call setup rate is within the supported capacity of\n\ this gateway."

HTSP-3-NOEVENT

3-Error

no free event structure available from [chars] for DSP message

There were no event structures remaining in the system pools to alert the\n\ router of a voice or signaling event.

-

"Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port."

HTSP-3-CAPABILITYMISMATCH

3-Error

voice port [chars]: call connection id [0x[hec] 0x[hec] 0x[hec] 0x[hec]]

There was a capabilities mismatch between the two call legs.\n\ capabilities are negotiated between call legs for CODEC VAD and\n\ FAX rate.

-

"Check that the dial peer configuration is appropriate for the interface\n\ in question. Also check that and configuration on the interface is\n\ correct."

HTSP-3-DSPALARM

3-Error

voice port [chars]: status=0x[hec] message=0x[hec] text=[chars]

The DSP reported a fatal error. All calls on the DSP were dropped\n\ and a DSP reload was attempted.

-

"Verify that the DSP reloaded properly by attempting to place a call\n\ on the affected voice port. Contact your technical support\n\ representative include the full text of the error message."

HTSP-3-TRUNKNOTSUPPORTED

3-Error

voice port [chars]: Ground Start trunking not supported

This voice port does not support the 'connection trunk' command when\n\ ground start signaling is configured. Trunking mode on this voice\n\ is supported when using loop start signaling.

-

"Shut down the voice port remove the 'connection trunk' and/or\n\ 'signal groundStart' command from the voice port configuration\n\ and unshut the voice port."

HTSP-5-UPDOWN

5-Notice

Trunk portchannel [[chars]] is [chars]

Trunk port:channel changed state.

-

LOG_STD_NO_ACTION

HTSP-3-CADENCENOTSUPPORTED

3-Error

voice port [chars]: ring cadence not suitable for caller id. on_time_first=[dec] off_time_first=[dec] on_time_second=[dec] off_time_second=[dec]

Ring off period is not sufficient for caller id transmission.\n\ If caller id transmission during ring is configured make sure\n\ that the ring off duration is long enough.

-

"If caller id transmission during ring is configured make sure\n\ that the ring off duration is long enough. Make sure that the\n\ cptone setting and caller-id alerting settings are correct."

HTSP-5-VPM_BUSYOUT

5-Notice

voice port [chars]: [chars] busyout

voice port busyout status changed

-

"use SHOW VOICE BUSYOUT to find out the reason why voice port busyout\n\ monitoring is triggered"

HTSP-5-VPM_PCM_CAPTURE

5-Notice

User trigger PCM capture is [chars] on voice port [chars]

User trigger PCM capture is enabled or disable on this voice port

-

"This is just for information only"

HTSP-5-VPM_CABLE_STAT

5-Notice

voice port [chars]: cable [chars]

Cable for analog voice port is reconnected or removed

-

"Check the cable connection for this analog voice port"

FARM_DSPRM-4-NOC5510WARN

4-Warning

dsp service dspfarm can not be configured for this card type.

There is C549 NM-HDV card configured for dspfarm service.\n\ Only one dspfarm card type is allowed.

-

"If C5510 card type dspfarm is desired then remove C549 NM-HDV dspfarm \n\ service and reconfigure dspfarm service for this card. "

FARM_DSPRM-6-CALLDROPINFO

6-Information

dspfarm active calls on this card dsp [dec] channel [dec] will be dropped.

The card has been removed. Dspfarm active calls on this card\n\ will be dropped.

-

"No action is required."

FARM_DSPRM-6-CARDREMOVEINFO

6-Information

dspfarm card slot [dec] is removed.

dspfarm card type is remvoed from the slot.

-

"No action is required."

FARM_DSPRM-6-CARDINSERTINFO

6-Information

dspfarm card slot [dec] is inserted.

dspfarm card type is inserted into the slot.

-

"No action is required."

DSPRM-5-UPDOWN

5-Notice

DSP [dec] in slot [dec] changed state to [chars]

The DSP resource changed state.

-

LOG_STD_NO_ACTION

DSPRM-5-UP_DOWN

5-Notice

DSP [dec] in subslot [chars] changed state to [chars]

The DSP resource changed state.

-

LOG_STD_NO_ACTION

DSPRM-5-KEEPALIVE

5-Notice

DSP [dec] in slot [chars] NOT RESPONDING - auto restart[dec] times

The DSP failed the background keep-alive test.

-

LOG_STD_NO_ACTION

DSPRM-3-INSUFFICIENT

3-Error

Insufficient DSP resources for timeslot [dec] on port [chars]

The configuration requires more DSP resources than are available.

-

"Change the configuration to specify fewer used timeslots.\n\ Install additional DSP resources to allow more complex\n\ configurations."

DSPRM-3-INSUFFICIENT_DSP

3-Error

\nvoice-port : [chars] Not initialized due to insufficient DSP resources

More DSP resources are needed to initialize the analog voice-port

-

"Install additional DSP resources to allow voice-port initialization"

DSPRM-5-DSPFAIL

5-Notice

DSP [dec] in slot [chars] is in the failed state

The DSP entered the FAILED state due to alarm indications.

-

"Replace the DSP resource."

DSPRM-5-DSPMSGFAIL

5-Notice

Failed to get dsprm msg for msg id [chars]

Unable to get dsprm control message

-

LOG_STD_NO_ACTION

DSPRM-5-JUKEBOX

5-Notice

Jukebox transmit overlay resp [dec] on slot [chars] failed

The Jukebox received failed response code.

-

""

DSPRM-5-JUKEBOX_UPDOWN

5-Notice

DSP Jukebox[dec] in slot [chars] changed state to [chars]

The DSP JUKEBOX changed state.

-

LOG_STD_NO_ACTION

DSPRM-5-SETCODEC

5-Notice

Configured codec [dec] is not supported with this dsp image.

Codec negotiation failed.

-

""

DSPRM-2-DSPALARM

2-Critical

Received alarm indication from dsp [dec]/[dec]. Resetting the DSP.

Fatal error detected in DSP.

voice-dsp

"contact your technical support representative."

DSPRM-3-DSPALARMINFO

3-Error

[chars]

DSP Alarm Data

-

""

DSPRM-5-NULLIDB_CREATE_FAIL

5-Notice

VoIP Null IDB creation failed.

VoIP nullidb creation failed.

-

""

DSPRM-2-FORKFAIL

2-Critical

Process creation of [chars] failed.

Failed to create the process.

c3800

LOG_STD_ACTION

DSPRM-5-DSP_VIC_CONFIG_NAK

5-Notice

Received VIC config NAK from DSP[dec]/[dec] resetting the DSP.

Receieved NAK message from DSP. Re-attempt initialization.

-

LOG_STD_NO_ACTION

FLEX_DNLD-1-NOPCIMEMORY

1-Alert

VPM [dec]/[dec] PCI memory unavailable.

The router or access server could not allocate memory for the\n\ descriptors.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

FLEX_DNLD-1-INCORRECT_DSP_ID

1-Alert

AIM VOICE at slot [dec] receives data from incorrect DSP-ID [dec].

The DSP ID provided by FPGA for download is not valid.

-

" Call your technical support representative for assistance."

FLEX_DNLD-3-ERROR_FIRMWARE_DNLD

3-Error

DSP firmware download fails for slot [dec] dsp_id [dec]

Error initializing the DSP with the application firmware.

-

" Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance."

FLEX_DNLD-3-NO_FIRMWARE_DNLD

3-Error

No DSP firmware download invoked for slot [dec] no DSPs on the card

No DSP on the card.

-

"Plug in DSP on the Network Module"

FLEX_DNLD-1-TOOBIG

1-Alert

[chars] packetsize [dec] too big.

A packet greater than the 264 bytes received on this interface.

-

"The system should recover. No action is required.\n\ \n\ If the problem reccurs it indicates an error that might be\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative."

FLEX_DNLD-3-ERROR_ANALYZE

3-Error

Error analyzing the device in slot [dec].

The Port module in this slot could not be recognized.

-

"Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance."

FLEX_DNLD-1-NO_RING_DESCRIPTORS

1-Alert

No more ring descriptors available on slot [dec] dsp [dec].

The dspfw dnld driver cannot queue messages upto the egress queue for FPGA to transmit.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. Reset the DSP's on this port \n\ module."

LIBT2F-3-GETBUFFER_FAILED

3-Error

Cannot allocate a packet\n\from shared memory

The system is running low on packet memory. The fax cannot be\n\sent correctly.

-

LOG_STD_ACTION

LIBT2F-3-NULL_BUFFER

3-Error

A text buffer is NULL

An internal error occurred in the text buffer processing. The\n\fax tranmission be aborted.

-

LOG_STD_ACTION

LIBT2F-2-NEW_CONTEXT

2-Critical

A new text2fax context could not be created

An internal error occurred in the initialization of the\n\text2fax engine. The fax transmission will be aborted.

-

LOG_STD_ACTION

LIBT2F-3-ENGINE_FAILED

3-Error

The text2fax engine failed

This occcurred most likely due to a memory limitation or\n\illegal data being passed into the text2fax engine. The fax\n\transmission will be aborted

-

LOG_STD_ACTION

ENSP-6-SMTP_OPEN

6-Information

SMTP- opening [chars] [dec]

A connection attempt ...

-

LOG_STD_NO_ACTION

ENSP-4-SMTP_NOT_CONNECTED

4-Warning

SMTP- failed [chars] [dec]

A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior.

-

LOG_STD_NO_ACTION

ENSP-2-INTERNAL_ERROR

2-Critical

FAX- Internal software error: [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

ENSP-1-NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

ENSP-4-FMAIL_BAD_MESSAGE

4-Warning

FAXMAIL- Bad message received

An unexpected message was received.

-

LOG_STD_RECUR_ACTION

ENSP-4-FMAIL_NO_SMTP

4-Warning

FAXMAIL- Can not connect\n\to the SMTP server

No connection was able to be created to any of the specified\n\SMTP servers.

-

LOG_STD_RECUR_ACTION

ENSP-4-FMAIL_NO_SMTP_SEND

4-Warning

FAXMAIL- Could not\n\send data to the SMTP server

A connection was made to the SMTP server but no data can be sent.

-

LOG_STD_RECUR_ACTION

ENSP-2-FMAIL_NO_AUTH_STARTED

2-Critical

AAA authentication startup failed

AAA authentication startup failed

-

LOG_STD_RECUR_ACTION

ENSP-2-FMAIL_INTERNAL_ERROR

2-Critical

Internal software error

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

FTSP-6-FAX_CONNECT

6-Information

[chars]

Fax carrier detected

-

LOG_STD_NO_ACTION

FTSP-6-FAX_DISCONNECT

6-Information

[chars]

Fax call disconnected

-

LOG_STD_NO_ACTION

FTSP-2-INTERNAL_ERROR

2-Critical

Internal software error. [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

FTSP-4-HARDWARE_ERROR

4-Warning

tty [dec]

A hardware interface was not configured when a fax call was\n\ answered or attempted.

-

LOG_STD_RECUR_ACTION

FTSP-4-UNEXPECTEDEVENT

4-Warning

Bad event received\n\[dec] [dec]

An unexpected event was received.

-

LOG_STD_RECUR_ACTION

FTSP-1-NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

FTSP-4-FMAIL_NO_ACCOUNTING

4-Warning

FAXMAIL- Accounting\n\for tty[dec] failed

Accounting failed for the specified tty.

-

LOG_STD_RECUR_ACTION

FTSP-4-FMAIL_FAILED_AUTHENTICATION

4-Warning

Authentication for > [chars] < failed\n

Authenticating the specified user failed

-

LOG_STD_RECUR_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NORMAL

6-Information

Normal call clearing

Call clearing occurred normally

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_INTERNAL

6-Information

Internal error occured

Call aborted due to an internal error

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_MEMORY

6-Information

No memory available

Call aborted due to insufficient memory being available

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_AUTH_FAILED

6-Information

User authentication failed

Call aborted due to user authentication failure

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_VTSP_DISCONNECTED

6-Information

Telephony interface VTSP disconnected

Call termination due to Telephony interface disconnect

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_FMSP_DISCONNECTED

6-Information

Fax protocol FMSP disconnected

Call aborted due to Fax sessionFMSP disconnect

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_DMSP_DISCONNECTED

6-Information

Document Media Service DMSP disconnected

Call aborted due to Document Media Service DMSP disconnect

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_DMSP_DISCONNECTED_NO_ROUTE

6-Information

DMSP - no route - likely - ESMTP client did not connect to remote server

Call aborted due to DMSP no route disconnect - likely reason being no ESMTP connection to remote server

-

LOG_STD_NO_ACTION

LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT

6-Information

ESMTP client did not connect or lost connection to remote server

Call aborted due to loss of outbound ESMTP connection to remote server

-

LOG_STD_NO_ACTION

MSPI-6-SMTP_OPEN

6-Information

SMTP- opening [chars] [dec]

A connection attempt ...

-

LOG_STD_NO_ACTION

MSPI-4-SMTP_NOT_CONNECTED

4-Warning

SMTP- failed [chars] [dec]

A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior.

-

LOG_STD_NO_ACTION

MSPI-4-MSPI_BAD_MESSAGE

4-Warning

MSPI- Bad message received: [chars]

An unexpected message was received.

-

LOG_STD_RECUR_ACTION

MSPI-4-MSPI_NO_SMTP

4-Warning

MSPI- Can't connect to the SMTP server cid=[dec] [chars]

No connection was created to the specified SMTP server.

-

"Please use the following commands to collect the information: show call active " "voice show call active fax show call history voice show call history fax " "debug mspi send debug mspi receive or debug fax mspi all"

MSPI-4-MSPI_NO_SMTP_SEND

4-Warning

MSPI- Could not\n\send data to the SMTP server cid=[dec] [chars]

A connection was made to the SMTP server but no data can be sent.

-

"Please use the following commands to collect the information on why no data " "can be sent: show call active voice show call active fax show call history " "voice show call history fax debug mta send all debug mta receive all or " "debug fax mta all"

MSPI-2-MSPI_INTERNAL_ERROR

2-Critical

MSPI-Internal software error cid=[dec] [chars]

An internal software error occurred. This would happen when the IOS software runs into any null pointer invalid state or event or other failed operation

-

LOG_STD_RECUR_ACTION

MSPI-2-MSPI_BAD_CONTEXT

2-Critical

MSPI-bad context pointer [chars]

A bad context pointer was passed.

-

LOG_STD_RECUR_ACTION

MSPI-1-NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

MSPI-1-MSPI_BAD_CONFIG

1-Alert

MSPI-bad configuration [chars]

A configuration error was detected.

-

"Add or fix the Dial Peer configuration"

LAPP_OFF-6-LAPP_OFF_CAUSE_ABNORMAL

6-Information

Call aborted cause = 0x[hec]

Call Aborted due to abnormal error

-

LOG_STD_NO_ACTION

LAPP_OFF-6-SMTP_OPEN

6-Information

SMTP- opening [chars] [dec]

A connection attempt ...

-

LOG_STD_NO_ACTION

LAPP_OFF-4-SMTP_NOT_CONNECTED

4-Warning

SMTP- failed [chars] [dec]

A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior.

-

LOG_STD_NO_ACTION

LAPP_OFF-2-INTERNAL_ERROR

2-Critical

Internal software error [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

LAPP_OFF-1-NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

LAPP_OFF-4-LAPP_OFF_BAD_MESSAGE

4-Warning

LAPP_OFF- Bad message received

An unexpected message was received.

-

LOG_STD_RECUR_ACTION

LAPP_OFF-4-LAPP_OFF_NO_SMTP

4-Warning

mmsp- Can't connect to the SMTP server

No connection was created to the specified SMTP server.

-

LOG_STD_RECUR_ACTION

LAPP_OFF-4-LAPP_OFF_NO_SMTP_SEND

4-Warning

FAXMAIL- Could not\n\send data to the SMTP server

A connection was made to the SMTP server but no data can be sent.

-

LOG_STD_RECUR_ACTION

LAPP_OFF-2-LAPP_OFF_INTERNAL_ERROR

2-Critical

Internal software error [chars] cid=[dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

LIBTIFF-4-COPY_QUALITY

4-Warning

Bad copy quality on tty\n\[dec]

Noisy phone lines or a bad modem caused this error

-

LOG_STD_RECUR_ACTION

LIBTIFF-3-BAD_DIALPEER

3-Error

Invalid dial peer tag [dec]

Invalid mmoip dial peer tag

-

LOG_STD_ACTION

LIBTIFF-3-GETBUFFER_FAILED

3-Error

Cannot allocate a packet\n\from shared memory

The system is running low on packet memory. The\n\fax cannot be sent correctly

-

-

LIBTIFF-3-NULL_BUFFER

3-Error

A tiff buffer is NULL

An internal error occurred in the tiff buffer\n\processing. The fax tranmission will be aborted.

-

LOG_STD_ACTION

LIBTIFF-3-NEW_CONTEXT

3-Error

A new tiff context could not be created

An internal error occurred in the initialization of the\n\tiff engine. The fax transmission will be aborted.

-

LOG_STD_ACTION

LIBTIFF-3-ENGINE_FAILED

3-Error

The tiff engine failed

This occcurred most likely due to a memory limitation or\n\illegal data being passed into the tiff engine. The fax transmission will be aborted

-

LOG_STD_ACTION

LIBTIFF-3-INVALID_BUFFER

3-Error

A tiff buffer is invalid

An internal error occurred in the tiff buffer\n\processing. The fax tranmission will be aborted.

-

LOG_STD_ACTION

MGCP-2-INTERNAL_CRITICAL

2-Critical

[chars]

The MGCP subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

MGCP-3-INTERNAL_ERROR

3-Error

[chars]

The MGCP subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

MGCP-4-INTERNAL_WARNING

4-Warning

[chars]

The MGCP subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-UNDEFVOICEINTRF

3-Error

Invalid voice interface slot/controller:group[dec]/[dec]:[dec]

The voice interface defined by controller:group is not\n\ yet defined within the voice software but attempts were\n\ made to use this interface.

xcc

"Internal software fault. Contact your field service \n\ representative if this message is coincident with \n\ dropped calls."

XCCTSP_VOICE-3-UNDEFDSX0

3-Error

Undefined dsx0 interface for controller[dec]

The dsx0 interface for the specified controller\n\ is not defined but the voice software use it.

xcc

"Internal software fault. Contact your field service representative \n\ if this message is coincident with dropped calls."

XCCTSP_VOICE-3-NOSDB

3-Error

No signaling data block is available to build the\n\ voice interface[dec]/[dec]:[dec] or DSP may not be present

The voice software was unable to obtain a signaling data\n\ block from the Voice Telephony Service Provider. \n\ The system may be out of memory.

xcc

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-ADDINTRFFAIL

3-Error

The Voice Telephony Service Provider has rejected our\n\ request to add this voice interface [dec]/[dec]:[dec]

The voice software was unable to report a new signaling\n\ interface to the Voice Telephony Service Provider

xcc

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-NOMEM

3-Error

No memory is available to build the voice interface [dec]:[dec]

The voice software was unable allocate memory to build \n\ a voice interface data structure. The system may be \n\ out of memory.

xcc

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-MALLOC

3-Error

No memory is available to build any internal data \n\ structure for the voice software.

The voice software was unable allocate memory to build \n\ any internal data structures. The system may be \n\ out of memory.

xcc

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-NOTDMCHNL

3-Error

XCCTSP failed to get a free dsp tdm channel from the DSP\n\ Resource Manager DSPRM to handle an incoming call

The voice software was unable to obtain the tdm channel \n\ for a free dsp from the DSP Resource Manager. All of \n\ the dsp's have been used to process calls or have\n\ been taken out of service.

xcc

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-NOVOICEVDEV

3-Error

Cannot find the voice data block which matches\n\ an asynchronous response for a call.

Internal software fault. Contact your field service representative \n\ if this message is coincident with dropped calls.

xcc

LOG_STD_SH_TECH_ACTION

XCCTSP_VOICE-3-OUTOFRANGE_CTRL

3-Error

Going out of range for controller number for the slot\n\ subslot [dec] ctrl_num [dec]

Internal software fault. Contact your field service representative

xcc

LOG_STD_SH_TECH_ACTION

FLEXDSPRM-5-CB_UPDOWN

5-Notice

Channel Bank [chars] state is [chars]

Channel Bank status has been changed

guido

"See if the voice ports in the channel bank are UP"

FLEXDSPRM-5-OUT_OF_RESOURCES

5-Notice

[chars]

Flex DSPRM temporarily fail to allocate a DSP for this call. A oversubscription has happened and the current free DSP MIPS/Credits are not sufficient to admit a new call.

hdv2 or pvdm3

"Check availability of router DSP resource" " and DSP sharing configurations"

FLEXDSPRM-6-DSP_USAGE

6-Information

DSP [chars] usage has reached [dec]%%

Usage of DSP resources has reached a certain percentage.

pvdm3

"Examine whether or not enough " "DSP resources are reserved."

FLEXDSPRM-3-TDM_CONNECT

3-Error

failed to connect voice-port [dec]/[dec]/[dec] to dsp_channel[dec]/[dec]/[dec]

TDM connection between Analog/VWIC and the DSP has failed

c2800 or c3800

LOG_STD_ACTION

FLEXDSPRM-5-TDM_SLOT

5-Notice

voice channel is being shared from slot [dec]. Configure network-clock-participate slot [dec]

Configure network-clock-participate slot for sharing DSPs

c2800 or c3800

LOG_STD_ACTION

FLEXDSPRM-3-UNSUPPORTED_CODEC

3-Error

codec [chars] is not supported on dsp [dec]/[dec]

Call failed due to the dsp does not support the codec.

PVDM3

"Check dsp capability and make the call on supported dsp"

IPV6_ROUTING-3-RIB

3-Error

[chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_ROUTING-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_ROUTING-4-MAXPDB

4-Warning

Exceeded maximum supported IPv6 Routing Protocol instances

This error indicates that configuration of a Routing Protocol has failed because it would exceed the maximum supported number of Routing Protocols

ipv6

"Reduce the number of IPv6 Routing Protocol" " instances configured"

IPV6_ROUTING-3-ROUTELIMITEXCEEDED

3-Error

IPv6 routing table limit exceeded - [chars]

The number of routes in the named IPv6 routing table has reached the configured limit. No further routes will be added to the table

ipv6

"Reduce the number of routes in the table or reconfigure the limit"

IPV6_ROUTING-3-ROUTELIMITWARNING

3-Error

IPv6 routing table limit warning - [chars]

The number of routes in the named IPv6 routing table has reached the configured warning limit.

ipv6

"Reduce the number of routes in the table or reconfigure the limit"

IPV6_ROUTING-6-ROUTELIMITRECOVERED

6-Information

IPv6 routing table limit recovered - [chars]

The number of routes in the named IPv6 routing table has fallen below the configured limit. The routing table has recovered

ipv6

LOG_STD_NO_ACTION

IPV6_ROUTING-4-REDIST_MAX_PFX

4-Warning

Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes

We have reached the maximum number of redistributed prefixes

-

"Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake"

IPV6_ROUTING-4-REDIST_THR_PFX

4-Warning

Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes

We have reached the threshold level of number of redistributed prefixes

-

"Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake"

MDNSPROXY-4-INIT_MDNS_FAIL

4-Warning

[chars] Initialisation failure.

An internal error occurred during mDNS initialisation.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-PORT_RESERVED_MDNS

3-Error

[chars] Initialisation failure.

UDP Port 5353 Already reserved. Please disable the feature which uses 5353 and And Try Again.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-CHUNK_MEMORY_FAIL

3-Error

Chunk memory allocation failed

Chunk memory allocation failed for Cache element

mDNS

LOG_STD_ACTION

MDNSPROXY-3-API_FAIL_MDNS

3-Error

[chars] API failed

An error occurred while calling the APIs.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-NULL_CONTEXT_ID_MDNS

3-Error

Encountered a NULL context for the ID [dec]

NULL context for the ID passed in id_to_ptr.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-OS_API_FAIL_MDNS

3-Error

IOS API [chars] failed

Encountered an error while calling the API.

mDNS

LOG_STD_ACTION

MDNSPROXY-3-STATIC_SERVICE_FAIL_MDNS

3-Error

Static Service: [chars]

Encountered an error while processing Static Service.

mDNS

LOG_STD_ACTION

SNMP_BULKSTAT-4-PRI_URL_UNREACHABLE

4-Warning

Primary network management station is unreachable for [chars]

The Collected Bulk data file could not be successfully \n\ transferred to the primary network management station address\n\ specified in the error message. This condition can occur \n\ because the primary network management address is not \n\ configured or the configured primary network management \n\ station address is unreachable. If a secondary network \n\ management station address is configured the collected bulk \n\ data file will be sent to the secondary network management \n\ station address.

dcm

"Ensure that the primary network management station address \n\ is configured. If the primary network management station \n\ address is configured check the connectivity to the\n\ destination indicated by the primary network management\n\ station address specified in the error message."

SNMP_BULKSTAT-4-SEC_URL_UNREACHABLE

4-Warning

Secondary network management station is unreachable for [chars]

The collected bulk data file could not be successfully \n\ transferred to the secondary network management station \n\ address destination specified in the error message. This \n\ condition can occur because the secondary network management \n\ station address is not configured or the configured secondary\n\ network management station address is unreachable. If a \n\ retention interval is not configured the bulk data file \n\ will be immediately deleted. If a retention interval is \n\ configured retries will be attempted for the configured \n\ number of times.

dcm

"Check the connectivity to destination indicated by secondary\n\ network management station address indicated in the error\n\ message"

SNMP_BULKSTAT-3-NO_MEMORY

3-Error

Memory not available for [chars] for [chars]

Data Collection or Transfer could not be successfully carried out because of lack of memory.

dcm

LOG_STD_REDUCE_ACTION

SNMP_BULKSTAT-4-BUFFER_OVERFLOW

4-Warning

Buffer size too small to accommodate data for one collection\n\ interval for [chars]

The bulk data file is too large for the configured buffer \n\ size for a single transfer interval. Data collection will \n\ continue in another new buffer of the configured size and \n\ the collected buffer will be transferred to the configured \n\ destination.

dcm

"Increase the maximum buffer size using the \n\ <CmdBold>buffer-size<NoCmdBold> size-of-buffer command \n\ where size-of-buffer is the increased buffer size."

SNMP_BULKSTAT-3-TOOSMALL_BUFFER

3-Error

Buffer size is insufficient to accommodate even the header part for [chars]

The buffer size is insufficient to accommodate the header \n\ for the bulk data file. The header contains the schema \n\ definitions of all the configured schemas.

dcm

"Increase the maximum buffer size using the \n\ <CmdBold>buffer-size<NoCmdBold> size-of-buffer command \n\ where size-of-buffer is the increased buffer size."

SNMP_BULKSTAT-3-REMOTE_FILE_WRITE_ERR

3-Error

File Write failed for the remote file [chars]

Username or password specified in the error message might\n\ not have the required privileges to write a file to the \n\ network management station specified in the error message\n\ or the destination directory specified in the error message\n\ is invalid.

dcm

"Ensure that the user name and password in the network \n\ management station address has the necessary privileges \n\ to write to the destination directory."

-

3-Error

fmt \ syslog_

-

-

-

-

3-Error

\ fmt

-

-

-

-

3-Error

-

BULKSTAT Service Enabled

SRVNAME_BULKSTAT

SYSLOGDOC_NO_ACTION

-

3-Error

-

BULKSTAT Service Disabled

SRVNAME_BULKSTAT

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CORE Service nabled

SRVNAME_DCM_CORE

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CORE Service Disabled

SRVNAME_DCM_CORE

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CLI_DP Service nabled

SRVNAME_DCM_CLI_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_CLI_DP Service Disabled

SRVNAME_DCM_CLI_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_SNMP_DP Service nabled

SRVNAME_DCM_SNMP_DP

SYSLOGDOC_NO_ACTION

-

3-Error

-

DCM_SNMP_DP Service Disabled

SRVNAME_DCM_SNMP_DP

SYSLOGDOC_NO_ACTION

UDP-7-GLEAN_DISABLED

7-Debug

ARP gleaning from UDP has been disabled.

The ARP gleaning from UDP has been disabled.

-

"If you want ARP gleaning from UDP do ip arp gleaning udp."

UDP-7-NO_OUTINTF

7-Debug

No output interface for pkts received on [chars] forwarding from [inet] to [inet]

Output interface is NULL while forwarding UDP packets

-

"LOG_STD_ACTION"

L4F-2-INVALIDFLOW

2-Critical

Invalid L4F flow: 0x[hec]

An invalid L4F flow entry was detected.

layer4-forwarding

"If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance."

L4F-5-NOBUFFER

5-Notice

Cannot allocate buffer to send data on the flows [chars]:[dec] -> [chars]:[dec]

A buffer could not be allocated while trying to send data on the\n\ indicated flow. The issue could be due to low or fragmented memory.\n\ If the memory issue doesn't resolve automatically it could result\n\ in connection resets.

layer4-forwarding

"This is an informational message that potential points to low or\n\ fragmented memory which could happen if the router is running beyond\n\ its resource limits. Check the number of flows and the traffic rate\n\ going through the router and contact your technical support\n\ representative with that info for assistance."

L4F-2-SEMLOCKFAILURE

2-Critical

Cannot lock TCP semaphore on flow 0x[hec] with tcb 0x[hec]

Cannot obtain the semaphore lock for a TCB we expect to be able to lock.

layer4-forwarding

"If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance."

L4F-6-L4F_FLOW_CREATION_FAILED

6-Information

L4F flow creation failed [chars]

L4F flow entry creation failed due to an error.

layer4-forwarding

"If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance."

L4F-6-L4F_FLOW_LIMIT_EXCEED

6-Information

L4F flow limit was exceeded:[dec]

This is an informational message. L4F flow max limit was exceeded.

layer4-forwarding

"Issue the" "<CmdBold>show l4f statistics <NoCmdBold> command and " "contact your technical support representative and \n\ provide the representative with the gathered information."

L4F-4-L4F_REINJECT_HANDLE_ERROR

4-Warning

L4F reinject [chars]

L4F reinjection handle creation or update failed.

layer4-forwarding

"If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance."

TCP-2-BUFFER

2-Critical

Tty[t-line] buffering bug

An internal software error occurred.

tcp

"If this message recurs contact your technical support " "representative."

TCP-2-PUTBYTE

2-Critical

Tty[t-line] tcp_putbyte with blocking disabled

An internal software error occurred.

tcp

"If this message recurs contact your technical support " "representative."

TCP-2-HALFCLOSE

2-Critical

Tty[t-line] tcp_putbyte write disabled

TCP received a packet from a user application after the connection\n was already halfclosed.

tcp

"Determine which TCP application is still sending after\n" "the connection was halfclosed."

TCP-2-NOTREADY

2-Critical

[chars] called but TCP not initialized

An internal software error occurred.

tcp

"If this message recurs copy the message exactly as it appears and\n" "contact your technical support."

TCP-6-TOOBIG

6-Information

Tty[t-line] too many bytes of options [dec]

An internal software error occurred.

tcp

"Copy the error message exactly as it appears and report it to your\n" "technical support representative."

TCP-6-NOBUFF

6-Information

TTY[t-line] no buffer available

An internal software error occurred.

tcp

"Copy the error message exactly as it appears and report it to your\n" "technical support representative."

TCP-6-BADAUTH

6-Information

[chars] MD5 digest from [chars][dec] to [chars][dec][chars] tableid - [dec]

The system received a TCP packet with an invalid MD5 authentication\n digest on a connection endpoint. The message ends with the string\n \

-

-

TCP-2-ACCEPT

2-Critical

Callback failed to accept connection from [chars][dec] to [chars][dec] --

An internal software error occurred.

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-INTERCEPT

6-Information

[chars] count [dec]/[dec] 1 min [dec]

The TCP Intercept code has changed state.

tcp

"This message is for informational purposes but it may indicate\n" "a security problem."

TCP-3-NOTFOUND

3-Error

Connection info for [inet]:[dec] => [inet]:[dec] not found.

The TCP Intercept code was searching its database for information\n for a particular connection but this information was not found.

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-2-BADQUEUE

2-Critical

Multiple entry for packet [hec]

An internal software error occurred.

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-2-BADREFCNT

2-Critical

Tty[t-line]: Bad refcnt for packet 0x[hec] during retransmit [chars][dec] to [chars][dec] state [dec]

An internal software error occurred.

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-4-INVALIDTCB

4-Warning

Invalid TCB pointer: 0x[hec]

An invalid TCB is used.

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-2-BADTCBREFCNT

2-Critical

Bad TCB refcount: TCB 0x[hec] refcnt [dec]

An internal software error occurred

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-3-BADMSS

3-Error

Incorrect mss [dec] observed

MSS Maximum Segment Size became incorrect. TCP cannot guarantee\n

tcp

"This message occurs please check the interface MTU and increase\n" "it accordingly. If doing this a few times does not help please\n" "contact your technical support representative for assistance."

TCP-2-INVALIDTCPENCAPS

2-Critical

Invalid TCB encaps pointer: 0x[hec]

An invalid TCP ENCAPS is used.

tcp

"If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-INTERCEPTHASH

6-Information

Unable to allocate memory for TCP Intercept hash table

An internal software error occured

tcp

"Contact your technical support representative for assistance."

TCP-6-MD5NOSPACE

6-Information

Insufficient space for MD5 option

Insufficient space for MD5 option. This should not happen as\n MD5 option when requested needs to be honored and also given\n preference over other TCP options.

tcp

"Try unconfiguring TCP options if any and check if this error\n" "message goes away. Also copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AONOSPACE

6-Information

Insufficient space for AO option

Insufficient space for Auth option AO. This should not happen as\n

tcp

"Try unconfiguring TCP options if any and check if this error\n" "message goes away. Also copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AONOCURRKEY

6-Information

No TCP AO Current key configured

No TCP Authentication Option Current Key configured on the TCB.

tcp

"Configure the TCP key chain with valid key and associate with the application." "If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AONONEXTKEY

6-Information

No TCP AO Next key configured

No TCP Authentication Option Next Key configured on the TCB.

tcp

"Configure the TCP key chain with valid key and associate with the application." "If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AOMISMATCH

6-Information

TCP AO MAC Mismatch for connection from [chars][dec] to [chars][dec] tableid - [dec]

TCP Authentication Option MAC did not match between endpoints.

tcp

"Configure the TCP key on each end of the connection with the" " same key-string and algorithm and corresponding send/recv ids." "If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AOKEYEXPIRED

6-Information

TCP AO Key expired for connection from [chars][dec] to [chars][dec] tableid - [dec]

TCP Key specified in Authentication Option has expired on the receiver.

tcp

"Configure the TCP key with a valid send/accept lifetime." "If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AOKEYSENDEXPIRED

6-Information

TCP AO Keychain [chars] key [dec] send lifetime expired

TCP Authentication Option key has expired.

tcp

"Configure the TCP key with a valid send lifetime." "If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AOKEYRECVEXPIRED

6-Information

TCP AO Keychain [chars] key [dec] accept lifetime expired

TCP Authentication Option key has expired.

tcp

"Configure the TCP key with a valid accept lifetime." "If this message recurs copy it down exactly as it appears and\n" "contact your technical support representative for assistance."

TCP-6-AOMISSING

6-Information

TCP Authentication Option not found for connection from [chars][dec] to [chars][dec] tableid - [dec]

TCP Authentication Option missing on connection.

tcp

"Check BGP/LDP/SXP configuration on each peer" " to make sure TCP AO is configured." "If this message recurs copy it down exactly as it appears and\n" "Contact your technical support representative for assistance."

TCP-6-AOROLLOVER

6-Information

TCP AO Keychain [chars] rollover from key [dec] to key [dec]

TCP AO Key chain is rolling over to a new key.

tcp

"No action required."

TCP-3-FORKFAIL

3-Error

Failed to start a process to negotiate options.

Failed to create a process to handle requests from\n client. It could be because of Insufficient memory.

tcp

"Free up some memory."

TCP-3-TCBHASHSIZE

3-Error

Failed to get tcb hash size from RFD Assigning default value [dec].

Failed to get tcb hash size from RFD file using RFD APIs.

os

"Contact your technical support representative" " for assistance."

-

3-Error

fmt \local_errmsg_t msg_ ## fac ## _ ## name = { #name

-

-

-

-

3-Error

fmt \extern C local_errmsg_t msg_ ## fac ## _ ## name

-

-

-

NBAR-5-PP_AUTO_UPDATE_FILE_COPY_SUCCESS

5-Notice

succesfully copied file \[chars]\

NBAR protocol-pack Auto-Update succesfully updated the PPACK file

-

"No action required. Informational message"

NBAR-3-PP_AUTO_UPDATE_FILE_COPY_FAIL

3-Error

failed to copy file \[chars]\

NBAR protocol-pack Auto-Update failed to update the PPACK file

nbar

"Check PPack auto-update server address"

NBAR-6-PP_AUTO_UPDATE_FILE_VALIDITY_SUCCESS

6-Information

succefully verified file \[chars]\

NBAR protocol-pack Auto-Update succesfully checked file validity

-

"No action required. Informational message"

NBAR-3-PP_AUTO_UPDATE_FILE_VALIDITY_FAIL

3-Error

failed to verify file \[chars]\

NBAR protocol-pack Auto-Update failed to verify file validity

nbar

"Check PPack auto-update server address"

NBAR-6-PP_AUTO_UPDATE_PREV_PP_DELETE_SUCCESS

6-Information

succefully deleted previous PP file \[chars]\

NBAR protocol-pack Auto-Update succefully deleted the prevously loaded protocol pack

-

"No action required. Informational message"

NBAR-6-PP_AUTO_UPDATE_PREV_PP_DELETE_FAIL

6-Information

failed to delete previous PP file \[chars]\

NBAR protocol-pack Auto-Update failed to delete the prevously loaded protocol pack

nbar

"Check if previous ppack still exists and if the disk is write protected"

NBAR-3-PP_AUTO_UPDATE_GENERIC_ERR

3-Error

Generic PP_UPDATE Error: \[chars]\

NBAR protocol-pack Auto-Update error

nbar

"None"

NBAR-4-PP_AUTO_UPDATE_GENERIC_WARNING

4-Warning

Generic PP_UPDATE Warning: \[chars]\

NBAR protocol-pack Auto-Update warning

nbar

"None"

NBAR-6-PP_AUTO_UPDATE_GENERIC_INFO

6-Information

Generic PP_UPDATE Information: \[chars]\

NBAR protocol-pack Auto-Update information

-

"None"

NBAR-4-AUTO_CUSTOM_GENERIC_HOST_WARNING

4-Warning

[chars]

-

-

-

NBAR-4-AUTO_CUSTOM_UNCLASSIFIED_PORT_WARNING

4-Warning

[chars]

-

-

-

NBAR-6-CACHE_SYNC_INFO

6-Information

[chars]

-

-

-

NBAR-4-CACHE_SYNC_WARN

4-Warning

[chars]

-

-

-

NBAR-3-CACHE_SYNC_ERR

3-Error

[chars]

-

-

-

NBAR_HA-5-NBAR_INFO

5-Notice

[chars]

-

-

-

NBAR-2-NOMEMORY

2-Critical

No memory available for [chars]

An attempt at memory allocation failed.

high-ipqos

"Try these actions to remedy the problem:\n\\n\ Add memory.\n\\n\ Disable some features.\n\\n\ Apply filtering to decrease the size of system data structures - the\n\ routing table for example.\n\\n\ In general reduce other system activities to ease memory demands. If\n\ conditions warrant upgrade to a larger memory configuration."

NBAR-2-RMNORESOURCE

2-Critical

NBAR resources exhausted

In order to save stateful information on protocols NBAR must\n\ use dynamic resources. These resources have been exhausted.

high-ipqos

"Configure the router with the <CmdBold>ip nbar resources\n\ <noCmdBold> to allocate a larger initial pool of resources.\n\ The default number of initial resources is 10000. Also try\n\ configuring a shorter max-idle time."

NBAR-2-RMINVALIDCONFIG

2-Critical

NBAR resource manager : too many buckets [dec]

-

-

-

NBAR-2-NOSTATEMEM

2-Critical

Memory for maintaining state used up

NBAR uses memory to maintain state information about stateful\n\ flows. There is a maximum limit on how much memory NBAR can use\n\ for this purpose and this limit has been reached.

high-ipqos

"Increase memory on platform"

NBAR-2-HEURISTIC_XDR_FAILED

2-Critical

Failure in the heuristic subsystem of NBAR: [chars]

Failure during the distribution of NBAR heuristic data structures\n\ from the route processor to the linecards.

high-ipqos

"Disable heuristic protocols"

NBAR-1-LINKNEXTCORRUPTED

1-Alert

link->next not NULL when allocated. link->next = [chars]\n

An attempt was made to get a link from the free bucket\n\ which is pointing to another resource. Links within\n\ the free bucket should be NULL therefore this link is corrupted and\n\ should not be used

high-ipqos

"Configure the router with the <CmdBold>ip nbar resources\n\ <noCmdBold> to allocate a larger initial pool of resources."

NBAR-1-LINKPREVCORRUPTED

1-Alert

link->prev not NULL when allocated. link->prev = [chars]\n

An attempt was made to get a link from the free bucket\n\ which is pointing to another resource. Links within\n\ the free bucket should be NULL therefore this link is corrupted and\n\ should not be used

high-ipqos

"Configure the router with the <CmdBold>ip nbar resources\n\ <noCmdBold> to allocate a larger initial pool of resources."

NBAR-1-NODESIZEMISMATCH

1-Alert

Nodes size mismatch between parsing and sending:[chars] \n

Failure during the distribution of NBAR graph nodes from the route processor to the linecards. Failure is related to node size changes between parsing and sending phase

high-ipqos

"Disable nbar protocols"

NBAR-1-MAXMEMORYUSED

1-Alert

Reached maximum amount of memory allocated for stile\n

This platform allows NBAR to use a limited amount of memory for\n\ classification and that amount has been used up because of high \n\ traffic conditions.\n

high-ipqos

"Increase amount of memory in router.\n"

NBAR-4-STILE_MAX_PD_INTF

4-Warning

NBAR protocol-discovery is enabled on maximum number of interfaces [dec] supported by this platform

This platform allows NBAR to enable protocol-discovery on a limited number of interfaces and that limit has reached.

nbar

"Need to disable protocol-discovery from an interface to enable " "protocol-discovery on any new interface."

NBAR-6-INACTIVE_PROTOCOL_PACK

6-Information

[chars] is successfully loaded as an Inactive Protocol Pack

The NBAR Engine Version of the protocol pack is either less than the Minimum Backward Compatible Engine Version or is greater than the NBAR Engine Version of the image and therefore it will be loaded as an Inactive Protocol Pack

nbar

"Since the protocol pack is loaded as an Inactive Protocol Pack" "signatures in this pack will not be available for any classification." "To use the protocol pack upgrade/downgrade to an image " "which is compatible with the NBAR Engine Version of the " "protocol pack."

NBAR-6-PORT_MAP_DEPRECATION

6-Information

[chars] command will be deprecated soon.\n\ In future it will not be necessary to configure port-map on a Protocol to create a new\n\ Custom protocol onto the same well known port.

In future releases it will not be necessary to configure\n\ port-map on a Protocol to create a new Custom protocol onto\n\ the same well known port. Port-map command will be\n\ deprecated in future releases.

nbar

"No action required."

NBAR-6-PDL_ERRORS

6-Information

PDL parsing error: [chars]

Unable to parse PDL issue in syntax

nbar

"PL need to fine tune or modify PDL."

REQGRP-3-SYSCALL

3-Error

System call for command [dec] slot[dec]/[dec] : [chars] Cause: [chars]

-

-

-

REQGRP-3-RPCREQ

3-Error

RPC blocked message for client [dec] entity [dec] slot[dec]/[dec]: [chars]

-

-

-

REQGRP-3-NBLKQ

3-Error

[chars]

Nonblocking IPC queue initialization failure.

ubr10k-sw

LOG_STD_ACTION

REQGRP-3-DSPTCHQ

3-Error

[chars]

Disptach IPC queue initialization failure.

ubr10k-sw

LOG_STD_ACTION

REQGRP-3-NBLKENQFAIL

3-Error

[chars] slot [dec]/[dec]

-

-

-

REQGRP-3-ENQFAIL

3-Error

enqueue failed! queue:[chars] size:[dec]

process enqueue failed.

ubr10k-sw

LOG_STD_ACTION

REQGRP-6-NBLKEVT_Q_FULL

6-Information

Nonblocking IPC event queue full [dec] events

-

-

-

REQGRP-6-UNKLCREQ

6-Information

Received unknown IPC request [dec] from [dec]/[dec]

-

-

-

REQGRP-6-UNKVER

6-Information

Received IPC with unsupported version [dec]

-

-

-

REQGRP-6-CORRUPTIPC

6-Information

Corrupted IPC slot = [dec]/[dec] received at Cable[dec]/[dec]

Some code has cloberred the IPC message

ubr10k-sw

LOG_STD_ACTION

REQGRP-3-REQOP

3-Error

IPC request/response [dec] slot [dec]/[dec]: [chars]

Operational errors while processing an IPC Request.

ubr10k-sw

LOG_STD_ACTION

REQGRP-3-NORESP

3-Error

No response generated for IPC request [dec] slot [dec]/[dec]: [chars]

-

-

-

REQGRP-3-NOSESSION

3-Error

Unable to create client object for client [dec] entity [dec] slot [dec]/[dec]: [chars]

-

-

-

REQGRP-3-UNKCONN

3-Error

Unknow connection state [dec] from callback for client [dec] entity [dec] slot [dec]/[dec]

-

-

-

REQGRP-3-IPCTXERR

3-Error

IPC send failure: version=V1 msg=[dec] error=[chars] slot [dec]/[dec]

-

-

-

REQGRP-4-IPCWATERMARK

4-Warning

The size of request queue for slot[dec]/[dec] service type [dec] has exceed the high watermark [dec]

Several unblocked IPC message are pending in the request queue to get the ack. If the pending message are increasing it may result in the Memory leak.

ubr10k-sw

LOG_STD_ACTION

CR10K_CLNT-3-CR10K_ASSERT_FAILED

3-Error

Assert failed at line [dec] from func [chars] in file [chars]

Detect assert failure in global level

cmts-platform

"Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs"

CR10K_CLNT-3-CR10K_CLNT_ASSERT_FAILED

3-Error

Assert failed at line [dec] from func [chars] in file [chars] for client [dec]

Detect assert failure in client level

cmts-platform

"Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs"

CR10K_CLNT-3-TIMEOUT

3-Error

Timeout waiting for [chars] slot [dec]/[dec]

Timeout while waiting on the specified event.

cmts-platform

"Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs"

CR10K_CLNT-3-MTU_UNAVAILABLE

3-Error

cr10k client ses is down err:[dec]

Application code is trying to get negotiated mtu before issu negotiation is finished. err:1 means issu nego has not finished. err:2 means issu nego has not started.The traceback decode usually can pinpoint which routine is trying toget mtu too early. In most cases it is a msg send routine that triesto get the msg mtu in order to allocate a right size msg buffer. If the msg is not critical or will be resent upon send failure then the fix is to call cr10k_clnt_get_ses_up_for_apps before get mtu

cmts-platform

"Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs"

CR10K_CLNT-3-IPCTXERR

3-Error

IPC send failure: client=[dec] entity=[dec] ses=[dec]/[dec] msg=[dec] err=[chars]

IPC send failure.

cmts-platform

LOG_STD_ACTION

ELB_HA-2-INIT

2-Critical

ELB ISSU client initialization failed to [chars]. Error: [dec] [chars]

The ELB ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ethernet-oam

LOG_STD_ACTION

ELB_HA-3-TRANSFORM

3-Error

ELB ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The ELB ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ELB state between the active device and the standby device is not identical.

ethernet-oam

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ELB_HA-3-MSG_SIZE

3-Error

ELB ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The ELB ISSU client failed to calculate the MTU for the specified message. The ELB ISSU client will not able to send the message to the standby device.

ethernet-oam

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ELB_HA-3-INVALID_SESSION

3-Error

ELB ISSU client does not have a valid registered session.

The ELB ISSU client does not have a valid registered session.

ethernet-oam

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ELB_HA-2-SESSION_REGISTRY

2-Critical

ELB ISSU client failed to register session information. Error: [dec] [chars]

The ELB ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ethernet-oam

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ELB_HA-3-SESSION_UNREGISTRY

3-Error

ELB ISSU client failed to unregister session information. Error: [dec] [chars]

The ELB ISSU client failed to unregister session information.

ethernet-oam

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ELB_HA-2-SESSION_NEGO

2-Critical

ELB ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The ELB ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ethernet-oam

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ELB_HA-2-SEND_NEGO_FAILED

2-Critical

ELB ISSU client failed to send negotiation message. Error: [dec] [chars]

The ELB ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ethernet-oam

"show logging and show checkpoint client"

ELB_HA-2-GET_BUFFER

2-Critical

ELB ISSU client failed to get buffer for message. Error: [dec] [chars]

The ELB HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly.

ethernet-oam

"show logging and show checkpoint client"

E_CFM-3-LR_FROM_WRONG_FP

3-Error

received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination

An unknown destination sent a reply to a Loopback messages that was intended to another device.

ethernet-cfm

"Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message."

E_CFM-6-ENTER_LCK_INT

6-Information

Interface [chars] enters LCK defect condition for [chars] direction

Interface is put in OOS state through exec cli for input direction

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-EXIT_LCK_INT

6-Information

Interface [chars] exited LCK defect condition for [chars] direction

Interface has exited LCK defect condition.

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-ENTER_LCK

6-Information

local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] enters LCK defect condition

Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep service id.

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-EXIT_LCK

6-Information

local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] exited LCK defect condition

Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep service id.

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-ENTER_AIS_INT

6-Information

Interface [chars] enters AIS defect condition for [chars] direction

Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-EXIT_AIS_INT

6-Information

Interface [chars] exited AIS defect condition for [chars] direction

LOG_STD_NO_ACTION

ethernet-cfm

"Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state"

E_CFM-6-ENTER_AIS

6-Information

local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] enters AIS defect condition

Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep service id.

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-EXIT_AIS

6-Information

local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] exited AIS defect condition

Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep service id.

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-MAX_MEPS_EXCEEDED

6-Information

Maximum MEPs threshold exceeded in [chars] for domain [chars] service [chars] mac [enet] mpid [dec]

The number of remote MEP entries in CC database has exceeded the maximum MEPs configured. The current remote MEP is not saved in the CC database.

ethernet-cfm

"Verify that the correct number for maximum MEPs is specified in the " "configuration. If correct number of maximum MEPs is configured " "verify if any unexpected remote MEP is not part of the service via " "'show ethernet cfm maintenance remote' or 'show ethernet cfm mpdb' " "command"

E_CFM-6-REMOTE_MEP_UP

6-Information

Continuity Check message is received from a remote MEP with mpid [dec] [chars] MA name [chars] domain [chars] interface status [chars] event code [chars].

A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MA.

ethernet-cfm

"Information message only."

E_CFM-3-REMOTE_MEP_DOWN

3-Error

Remote MEP mpid [dec] [chars] MA name [chars] in domain [chars] changed state to down with event code [chars].

The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB

ethernet-cfm

"Check the remote CFM configurations using CFM " " utilities like traceroute and ping."

E_CFM-3-CROSS_CONNECTED_SERVICE

3-Error

Continuity Check message is received from remote MEP mpid [dec] with service MA name [chars] [chars] MAC: [enet] for service MA name [chars] of domain [chars] level [dec].

The Continuity Check message whose MA name or MA level is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network.

ethernet-cfm

"Configure the CFM MA name or MA level properly across " "the network."

E_CFM-3-FORWARDING_LOOP

3-Error

Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the MA name [chars].

The device is receiving its own CC messages for a particular vlan or evc within the same MA.

ethernet-cfm

"Configure the CFM maintenance points properly " "to avoid the forwarding loop."

E_CFM-3-CONFIG_ERROR

3-Error

CFM mis-configuration in the network. Continuity-check message is received from mac-address [enet] with duplicated mpid [dec] as configured locally for service MA name [chars] with [chars] of domain [chars].

The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MA.

ethernet-cfm

"Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association."

E_CFM-3-CROSSCHECK_MEP_MISSING

3-Error

The device does not receive any CC messages from a remote MEP with mpid [dec] MA name [chars] that it was expecting to be part of the [chars] in the domain [chars].

The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MA.

ethernet-cfm

"There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. "

E_CFM-3-CROSSCHECK_MEP_UNKNOWN

3-Error

The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the MA name [chars] in the domain: [chars].

The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MA.

ethernet-cfm

"Check whether the CFM crosscheck configurations " "are proper."

E_CFM-6-CROSSCHECK_SERVICE_UP

6-Information

The device received CC messages from all remote MEPs within a given MA name [chars] in the maintenance domain [chars].

The service configured either MA is up as it receives CC messages from all remote statically configured MEPs.

ethernet-cfm

"Information message only."

E_CFM-3-FAULT_ALARM

3-Error

A fault has occurred in the network for the local MEP having mpid [dec] [chars] for service MA name [chars] with the event code [chars].

This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other MA.

ethernet-cfm

"There could be a possible fault in the network. " "Check whether the cfm configurations are proper."

E_CFM-2-PD_CAPABILITY_UPDATE

2-Critical

Platform has indicated an invalid capability update which has been ignored.

Platform code has indicated that its capabilities have changed based on a configuration knob but the updated values were inconsistent.

ethernet-cfm

"This likely indicates a programming error in Platform code but should " "not present a problem unless either of MA Alias and SLM over xconnect " "features are required. See documentation for this platform/release."

E_CFM-2-INIT_ALLOC_FAIL

2-Critical

Failed to allocate memory required for initialization.

CFM failed to allocate a memory required for the feature to operate correctly. This likely indicates a resource limitation or an attempt to use the software on unsupported hardware.

ethernet-cfm

"Confirm that the configured scale does not exceed the permitted limits " "for the hardware and that any other resource issues are resolved. If " "problems are still observed copy the error message exactly as it " "appears on the console or in the system log call your Cisco technical " "support representative and provide the representative with the " "gathered information. "

E_CFM-3- MAC_STATUS_CHANGE_FAIL

3-Error

Failed to set MAC layer operational state for [chars] to [chars].

CFM failed to update the state of the MAC layer for the specified interface in response to a change in the errors detected on the interface. If the MAC layer state is incorrect it is possible that data traffic flow through the interface will be affected either by traffic unexpectedly being allowed to pass through the interface or by traffic unexpectedly being dropped.

ethernet-cfm

"Collect the output of <CmdBold>show tech-support ethernet-cfm<noCmdBold> " "as soon as possible after the problem is seen. " LOG_STD_ACTION

E_CFM-3- CONFIG_LOST

3-Error

Failed to update CFM internal state to reflect configuration change: [chars]

CFM failed to save the CFM configuration in response to the recent change. The reason for this may be due to a memory shortage. The user should resolve any memory problems and then check the CFM configuration and if necessary re-add any config that is missing.

ethernet-cfm

"Collect the output of <CmdBold>show tech-support ethernet-cfm<noCmdBold> " "as soon as possible after the problem is seen. " LOG_STD_ACTION

E_CFM-3- OIR_SAVE

3-Error

Failed to save CFM configuration on OIR removal: [chars]

CFM failed to save the CFM configuration that was previously present on the interface prior to the OIR event. The user may need to be manually reconfigure the interface on reinsertion.

ethernet-cfm

"Collect the output of <CmdBold>show tech-support ethernet-cfm<noCmdBold> " "as soon as possible after the problem is seen. " LOG_STD_ACTION

E_CFM-3- OIR_RESTORE

3-Error

Failed to restore CFM configuration on OIR insertion: [chars]

CFM failed to restore the CFM configuration that was previously present on the interface prior to the OIR event. The user may need to be manually reconfigure the interface instead.

ethernet-cfm

"Collect the output of <CmdBold>show tech-support ethernet-cfm<noCmdBold> " "as soon as possible after the problem is seen. " LOG_STD_ACTION

E_CFM-3- TIMEOUT_TOO_SMALL

3-Error

Attempted to start a timer with a value less than the minimum permitted [dec]ms defaulting to [dec]ms.

-

-

-

E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_START

6-Information

Ethernet Dataplane Latching Loopback Start on [chars]

Dataplane Latching Loopback is activated for the specified service

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_STOP

6-Information

Ethernet Dataplane Latching Loopback Stop on [chars]

Dataplane Latching Loopback is de-activated for the specified service

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_TIMER_EXPIRED

6-Information

Ethernet Dataplane Latching Loopback timer expired on [chars]

Dataplane Latching Loopback timer is expired for the specified service

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_TIMER_RESTARTED

6-Information

Ethernet Dataplane Latching Loopback timer restarted on [chars]

Dataplane Latching Loopback timer is restarted for the specified service

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_CONT_TIMER_EXPIRED

6-Information

Ethernet Dataplane Latching Loopback timer expired [chars]

Dataplane Latching Loopback timer is expired for the specified service

ethernet-cfm

"LOG_STD_NO_ACTION"

E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_CONT_STATE_CHANGE

6-Information

Ethernet Dataplane Latching Loopback state change [chars]

Dataplane Latching Loopback state changed for the specified service

ethernet-cfm

"LOG_STD_NO_ACTION"

ECFM_HA-2-INIT

2-Critical

ECFM ISSU client initialization failed to [chars]. Error: [dec] [chars]

The ECFM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ecfm

LOG_STD_ACTION

ECFM_HA-3-TRANSFORM

3-Error

ECFM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The ECFM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ECFM state between the active device and the standby device is not identical.

ecfm

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ECFM_HA-3-MSG_NOT_OK

3-Error

ECFM ISSU client 'Message Type [dec]' is not compatible

The ECFM ISSU client received an incompatible message from the peer device. The message cannot be processed.

ecfm

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ECFM_HA-3-MSG_SIZE

3-Error

ECFM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The ECFM ISSU client failed to calculate the MTU for the specified message. The ECFM ISSU client will not able to send the message to the standby device.

ecfm

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ECFM_HA-3-INVALID_SESSION

3-Error

ECFM ISSU client does not have a valid registered session.

The ECFM ISSU client does not have a valid registered session.

ecfm

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ECFM_HA-2-SESSION_REGISTRY

2-Critical

ECFM ISSU client failed to register session information. Error: [dec] [chars]

The ECFM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ecfm

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ECFM_HA-3-SESSION_UNREGISTRY

3-Error

ECFM ISSU client failed to unregister session information. Error: [dec] [chars]

The ECFM ISSU client failed to unregister session information.

ecfm

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ECFM_HA-2-SESSION_NEGO

2-Critical

ECFM ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The ECFM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ecfm

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ECFM_HA-2-SEND_NEGO_FAILED

2-Critical

ECFM ISSU client failed to send negotiation message. Error: [dec] [chars]

The ECFM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ecfm

"show logging and show checkpoint client"

ECFM_HA-2-GET_BUFFER

2-Critical

ECFM ISSU client failed to get buffer for message. Error: [dec] [chars]

The ECFM HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly.

ecfm

"show logging and show checkpoint client"

ECFM_HA-3- ISSU

3-Error

YO

Hi

ecfm

"Hello " LOG_STD_ACTION

ETHERNET_EVENT-4-MW_BW_CHANGE

4-Warning

Available microwave bandwidth for link with source MAC [chars] link ID [dec] on [chars] has changed due to [chars] current is [dec]Mbps nominal is [dec]Mbps.

The available microwave bandwidth has changed. The message indicates the reason why the bandwidth changed as well as the currently available bandwidth. If the message indicates that the change was due to VSM then an ITU-T Y.1731 Vendor-Specific Message has been received causing the available microwave bandwidth to be updated. If the message indicates that the change was due to periodic timeout then the local system has not received a VSM within the expected time period and so it has reset the bandwidth back to its nominal value. The current bandwidth represents the bandwidth currently available on the link while the nominal bandwidth represents the maximum bandwidth supported by the link when the microwave signal is not degraded.

ethernet-cfm

"If the current bandwidth is unexpectedly less than " "the nominal bandwidth then action may be required " "to restore the microwave bandwidth to its fully " "supported capacity."

PM_AGENT-7-TC_REQ

7-Debug

PMA_SRC_ADDR :[chars] PMA_DST_ADDR :[chars] PMA_DSCP :[dec] //PMA_APP_ID :[dec] //PMA_SPI :[dec] PMA_IS_INTNET :[dec]\n

A Traffic Class is Requested.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-TC_DELETE

7-Debug

PMA_TC_ID :[dec] PMA_SRC_ADDR :[chars] PMA_DST_ADDR :[chars] PMA_DSCP :[dec] //PMA_APP_ID :[dec] //PMA_SPI :[dec] PMA_IS_INTNET :[dec]\n

A Traffic Class is Deleted.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-TC_ADD

7-Debug

PMA_TC_ID :[dec] PMA_SRC_ADDR :[chars] PMA_DST_ADDR :[chars] PMA_DSCP :[dec] //PMA_APP_ID :[dec] //PMA_SPI :[dec] PMA_IS_INTNET :[dec]\n

A Traffic Class is Added.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-3-TC_ADD_UPDATE_ERROR

3-Error

TC Add/Update has Error: [chars] PMA_TC_ID :[dec] PMA_SRC_ADDR :[chars] PMA_DST_ADDR :[chars] PMA_DSCP :[dec] //PMA_APP_ID :[dec] //PMA_SPI :[dec] PMA_IS_INTNET :[dec]\n

A Traffic Class is not Added because of Error.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-TC_AGE_OUT

7-Debug

PMA_TC_ID :[dec] PMA_SRC_PFX :[chars] PMA_DST_PFX :[chars] PMA_DSCP :[dec]\n

A Traffic Class is Aged Out.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-TC_UPDATE

5-Notice

PMA_TC_ID :[dec] PMA_SRC_ADDR :[chars] PMA_DST_ADDR :[chars] PMA_DSCP :[dec] //PMA_APP_ID :[dec] //PMA_SPI :[dec] PMA_OLD_PATH_COUNT :[dec] PMA_NEW_PATH_COUNT :[dec] PMA_IS_INTNET :[dec]\n

A Path change is made.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-6-HOP_CHAN_ADD

6-Information

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec]\n

A Hop Channel was Added.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-3-HOP_CHAN_ADD_FAILURE

3-Error

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec]\n

A Hop Channel failed to be added.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-6-HOP_CHAN_DELETE

6-Information

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec]\n

A Hop Channel was Deleted.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-6-HOP_CHAN_DELETE_FAILURE

6-Information

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec]\n

A Hop Channel failed to be deleted.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-HOP_CHAN_UPDATE

5-Notice

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec]\n

A Hop Channel was Updated.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-HOP_CHAN_UPDATE_FAILURE

5-Notice

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec]\n

A Hop Channel failed to be updated.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-HOP_CHAN_STATUS_CHG

5-Notice

PMA_HOP_ID : %lu PMA_DEST_SITE_ID : %lu PMA_REMOTE_IF_ID : %lu PMA_LOCAL_IF_ID : %lu PMA_DSCP : [dec] PMA_TX_STATE : [chars] PMA_RX_STATE : [chars]\n

Hop Channel Reachablity Status Changed.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-SITE_PREFIX_ADD

7-Debug

PMA_TABLE_ID : [dec] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec] PMA_PFX_FLAG : [chars]\n

A Site Prefix is Added.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-3-SITE_PREFIX_ADD_ERROR

3-Error

[chars] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec] PMA_PFX_FLAG : [chars]\n

A Site Prefix is not Added Because of Error.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-SITE_PREFIX_UPDATE

5-Notice

PMA_TABLE_ID : [dec] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec] PMA_PFX_FLAG : [chars]\n

A Site Prefix is Updated.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-SITE_PREFIX_DELETE

7-Debug

PMA_TABLE_ID : [dec] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec] PMA_PFX_FLAG : [chars]\n

A Site Prefix is Deleted.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-3-ESON_UP

3-Error

\n

Eson is Up.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-3-ESON_DOWN

3-Error

\n

Eson is Down.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-TCP_UP

5-Notice

TCP EVENT. PMA_SITE_ID :[dec] PMA_TENANT_ID :[dec] PMA_DVC_ID :[dec] PMA_TCP_STATUS :[chars] PMA_PMCS_ADDR :[chars]\n

TCP is Up.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-TCP_DOWN

5-Notice

TCP EVENT. PMA_SITE_ID :[dec] PMA_TENANT_ID :[dec] PMA_DVC_ID :[dec] PMA_TCP_STATUS :[chars] PMA_PMCS_ADDR :[chars]\n

TCP is Down.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-PMA_UP

5-Notice

PMA is Up.\n

PMA is Up.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-2-PMA_DOWN

2-Critical

PMA is Down.\n

PMA is Down.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-RLOC_REGISTER

5-Notice

PMA_INTERFACE_ID : %lu\n

An Rloc was Registered.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-RLOC_DEREGISTER

5-Notice

PMA_INTERFACE_ID : %lu\n

An Rloc was Deregistered.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-RLOC_UP

5-Notice

PMA_INTERFACE_ID : %lu\n

An Rloc came Up.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-RLOC_DOWN

5-Notice

PMA_INTERFACE_ID : %lu\n

An Rloc went Down.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-RLOC_PROP_CHANGED

5-Notice

PMA_INTERFACE_ID : [dec] PMA_ESON_STATE : [chars]\n

An Rloc Property has Changed.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-RLOC_IP_ADDR_CHANGE

5-Notice

PMA_INTERFACE_ID : %lu PMA_IF_ADDRESS : [chars]\n

An Rloc IP Address has Changed.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-PREFIX_TO_SITE_ADD

7-Debug

PMA_TABLE_ID : [dec] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec] PMA_PFX_FLAG : [chars]\n

A Dst Prefix to SiteID is Added.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-PREFIX_TO_SITE_UPDATE

7-Debug

PMA_TABLE_ID : [dec] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec] PMA_PFX_FLAG : [chars]\n

A Dst Prefix to SiteID is Updated.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-PREFIX_TO_SITE_DELETE

7-Debug

PMA_TABLE_ID : [dec] PMA_INSTANCE_ID : [dec] PMA_PFX_ADDR : [chars] PMA_PFX_MSK_LEN : [dec]\n

A Dst Prefix to SiteID is Deleted.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-SITE_TO_NH_ADD

7-Debug

PMA_DEST_SITE_ID : [dec] PMA_HOP_ID : [dec] PMA_HOP_ID : [dec]\n

A SiteID to NextHop is Added.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-SITE_TO_NH_UPDATE

7-Debug

PMA_DEST_SITE_ID : [dec] PMA_HOP_ID : [dec] PMA_HOP_ID : [dec]\n

A SiteID to NextHop is Updated.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-7-SITE_TO_NH_DELETE

7-Debug

PMA_DEST_SITE_ID : [dec] PMA_HOP_ID : [dec] PMA_HOP_ID : [dec]\n

A SiteID to NextHop is Deleted.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-5-HA_STATUS_CHANGE

5-Notice

[chars] PMA_PMCS_ADDR : [chars]\n

HA Status has Changed.

pathmgr

LOG_STD_NO_ACTION

PM_AGENT-3-LOCK_FAIL

3-Error

Can't lock pathmgr database: [chars]

Access to pathmgr data is protected by a locking mechanism. An operation tried to read or write provisioning data but was unable to get control of the lock.

pathmgr

"Any Cisco iwan-router or iwan related configuration" "or show commands that you were attempting to " "run may not have succeeded. Please try the operation again.\n\n" "Contact support if this message is seen frequently."

PM_AGENT-3-LOCK_RELEASE_FAIL

3-Error

Can't release the lock of pathmgr database: [chars]

Access to pathmgr data is protected by a locking mechanism. An operation tried to release the acquired read or write lock but was unable to.

pathmgr

"Any Cisco iwan-router or iwan related configuration" "or show commands that you were attempting to " "run may not have succeeded. Please try the operation again.\n\n" "Contact support if this message is seen frequently."

PM_AGENT-7-TEST

7-Debug

[chars]

-

-

-

ONEP_LISP-3-DISABLED_ERR

3-Error

[[chars]]: [chars] is disabled.

The requested service set is in disabled state. All the service requests for that service set will be rejected.

onep

"Make sure the service set is enabled. " "onep " " service set lisp"

ONEPSYNC_ISSU-2-INIT

2-Critical

Onepsync ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Onepsync ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

onep

LOG_STD_ACTION

ONEPSYNC_ISSU-3-MSG_NOT_OK

3-Error

Onepsync ISSU client 'Message Type [dec]' is not compatible

The Onepsync ISSU client received an incompatible message from the peer device. The message cannot be processed.

onep

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ONEPSYNC_ISSU-3-MSG_SIZE

3-Error

Onepsync ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Onepsync ISSU client failed to calculate the MTU for the specified message. The Onepsync ISSU client is not able to send the message to the standby device.

onep

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ONEPSYNC_ISSU-3-INVALID_SESSION

3-Error

Onepsync ISSU client does not have a valid registered session.

The Onepsync ISSU client does not have a valid registered session.

onep

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ONEPSYNC_ISSU-2-SESSION_REGISTRY

2-Critical

Onepsync ISSU client failed to register session information. Error: [dec] [chars]

The Onepsync ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

onep

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ONEPSYNC_ISSU-3-SESSION_UNREGISTRY

3-Error

Onepsync ISSU client failed to unregister session information. Error: [dec] [chars]

The Onepsync ISSU client failed to unregister session information.

onep

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ONEPSYNC_ISSU-2-SESSION_NEGO_FAIL_START

2-Critical

Failed to start Onepsync ISSU session negotiation. Error: [dec] [chars]

The Onepsync ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly.

onep

"show issu session <client_id>"

ONEPSYNC_ISSU-2-SEND_NEGO_FAILED

2-Critical

Onepsync ISSU client failed to send negotiation message. Error: [dec] [chars]

The Onepsync ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

onep

"show logging and show checkpoint client"

ONEPSYNC_ISSU-2-GET_BUFFER

2-Critical

Onepsync ISSU client failed to get buffer for message. Error: [dec] [chars]

The Onepsync ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

onep

"show logging and show checkpoint client"

ONEP_BASE-3-VERSION_ERR

3-Error

[[chars]]: ONE-P version incompatible between client and network element. [chars]

The ONE-P client service set version is incompatible with the one installed on the network element

onep

"Make sure the version running on the client side is compatible " "with the one installed on the network element "

ONEP_BASE-3-DISABLED_ERR

3-Error

[[chars]]: [chars] is disabled.

The requested service set is in disabled state. All the service requests for that service set will be rejected.

onep

"Make sure the service set is enabled. " "onep " " service set <name>"

ONEP_BASE-6-SS_ENABLED

6-Information

ONEP: [chars]

The service set has been set to an enabled state. The features of the service set will be available for use.

onep

"If the enablement was intentional no action is required."

ONEP_BASE-6-SS_DISABLED

6-Information

ONEP: [chars]

The service set has been set to a disabled state. All service requests for that service set will be rejected.

onep

"If the disablement was intentional no action is required." "If not then enable the service set:" "onep " " service set <name>"

ONEP_BASE-3-DUPLICATE_ERR

3-Error

[[chars]]: Requested entity [chars] already exists.

The connection request to the network element already exists

onep

"Make sure the uniqueness of the application name." "One session per application is allowed on a network element."

ONEP_BASE-3-AUTHEN_ERR

3-Error

[[chars]]: Authentication/authorization failed. [chars]

The session authentication has failed

onep

"Check user's credentials are matched against the AAA/local " "users configured on the Netwk Element."

ONEP_BASE-3-BUSY_ERR

3-Error

[[chars]]: The requested resource is currently busy. [chars].

The usage of the resource has exceeded the configured threshold value

onep

"Check the current resource usage and configured resource threshold." " cpu threshold rising <value> falling <value> interval <seconds>" "Retry the operation if resource usage is below the threshold."

ONEP_BASE-3-SESSION_ERR

3-Error

[[chars]]: ONEP session maximum is exceeded. [chars].

The application session has exceeded the configured maximum

onep

"Check the configured session maximum value and adjust accordingly." ">session max <value>" "Retry the session establishment or adjust the configured session maximum."

ONEP_BASE-3-STARTUP_ERR

3-Error

[[chars]]: Start up ONEP failed. [chars].

Fail to start ONEP due to error

onep

"Check transport is configured correctly or reboot the device"

ONEP_BASE-4-CLEAR_TEXT_TRANSPORT_WARN

4-Warning

[[chars]]: Clear text transport being enabled. This is not recommended for production environment. [chars]

Clear text transport being enabled. This is not recommended for production environment.

onep

"Please configure secure transport such as TLS."

ONEP_BASE-6-HISTORY

6-Information

[chars]

This syslog message is used to display onePK history messages when the 'history syslog' onep command is enabled.

onep

"No action is required. Use 'no history syslog' at the onep " "configuration prompt to turn off this logging if desired."

ONEP_BASE-6-CONNECT

6-Information

[[chars]]: ONEP session [chars] has connected.

A new ONEP session has been established with network element.

onep

"No action is required if this is an authorized session."

ONEP_BASE-6-RECONNECT

6-Information

[[chars]]: ONEP session [chars] has reconnected.

ONEP session has been reconnected after being disconnected temporarly. This disconnect can happen due to intermittent network connectivity issues.

onep

"No action is required if this is an authorized session."

ONEP_BASE-6-DISCONNECT

6-Information

[[chars]]: ONEP session [chars]

ONEP session has been disconnected. A disconnect can happen when application has finished execution or there was a problem during execution including issue with network transport. If reconnect timer is configured Network Element will wait for application to reconnect within configured time before cleaning up session resources.

onep

"No action is required if it is a expected disconnected. If reconnect" " timer is configured session will wait for application to attempt" " reconnect request" "Use show tech-support onep to collect logs from Network Element"

ONEP_BASE-6-DISCONNECT

6-Information

-

The ONE-P client service set version is incompatible with the one installed on the network element

SRVNAME_ONEP

"Make sure the version running on the client side is compatible " "with the one installed on the network element "

ONEP_BASE-6-DISCONNECT

6-Information

-

The requested service set is in disabled state. All the service requests for that service set will be rejected.

SRVNAME_ONEP

"Make sure the service set is enabled. " "connectedapps " " service set <name>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The connection request to the network element already exists

SRVNAME_ONEP

"Make sure the uniqueness of the application name." "One session per application is allowed on a network element."

ONEP_BASE-6-DISCONNECT

6-Information

-

The session authentication has failed

SRVNAME_ONEP

"Check user's credentials are matched against the AAA/local " "users configured on the Netwk Element."

ONEP_BASE-6-DISCONNECT

6-Information

-

The usage of the resource has exceeded the configured threshold value

SRVNAME_ONEP

"Check the current resource usage and configured resource threshold." " cpu threshold rising <value> falling <value> interval <seconds>" "Retry the operation if resource usage is below the threshold."

ONEP_BASE-6-DISCONNECT

6-Information

-

Clear text transport being enabled. This is not recommended for production environment.

SRVNAME_ONEP

"Please configure secure transport such as TLS."

ONEP_BASE-6-DISCONNECT

6-Information

-

Administrator has disabled ONEP feature while application sessions were active. All active sessions have been terminated. To enable ONEP again use \'feature onep\' command in configuration mode.

SRVNAME_ONEP

"No action is required if this was deliberate operation. To enable " "ONEP again use \'feature onep\' command in configuration mode."

ONEP_BASE-6-DISCONNECT

6-Information

-

This syslog message is used to display onePK history messages when the 'history syslog' onep command is enabled.

SRVNAME_ONEP

"No action is required. Use 'no history syslog' at the onep " "configuration prompt to turn off this logging if desired."

ONEP_BASE-6-DISCONNECT

6-Information

-

The Network Element and Persistent Storage for the running-config are out of sync. If no other error has occurred the Network Element configuration will take precedence.

SRVNAME_ONEP

"Try reconfiguring the item possibly using the [no] form to restore " "a default value if a new one doesn't take. The 'show running-config' " "command should be used to see if this error persists."

ONEP_BASE-6-DISCONNECT

6-Information

-

The Network Element and Persistent Storage for the running-config are out of sync. If no other error has occurred the Network Element configuration will take precedence.

SRVNAME_ONEP

"Try reconfiguring the item possibly using the [no] form to restore " "a default value if a new one doesn't take. The 'show running-config' " "command should be used to see if this error persists."

ONEP_BASE-6-DISCONNECT

6-Information

-

The requested service set is in disabled state. All the service requests for that service set will be rejected.

SRVNAME_ONEP

"Make sure the service set is enabled. " "connectedapps " " service set lisp"

ONEP_BASE-6-DISCONNECT

6-Information

-

The service set has been set to an enabled state. The features of the service set will be available for use.

SRVNAME_ONEP

"If the enablement was intentional no action is required."

ONEP_BASE-6-DISCONNECT

6-Information

-

The service set has been set to a disabled state. All service requests for that service set will be rejected.

SRVNAME_ONEP

"If the disablement was intentional no action is required." "If not then enable the service set:" "onep " " service set <name>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

SRVNAME_ONEP

LOG_STD_ACTION

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client received an incompatible message from the peer device. The message cannot be processed.

SRVNAME_ONEP

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client failed to calculate the MTU for the specified message. The Onepsync ISSU client is not able to send the message to the standby device.

SRVNAME_ONEP

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client does not have a valid registered session.

SRVNAME_ONEP

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

SRVNAME_ONEP

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client failed to unregister session information.

SRVNAME_ONEP

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly.

SRVNAME_ONEP

"show issu session <client_id>"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

SRVNAME_ONEP

"show logging and show checkpoint client"

ONEP_BASE-6-DISCONNECT

6-Information

-

The Onepsync ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

SRVNAME_ONEP

"show logging and show checkpoint client"

ONEP_BASE-6-DISCONNECT

6-Information

-

A new ONEP session has been established with network element.

SRVNAME_ONEP

"No action is required if this is an authorized session."

ONEP_BASE-6-DISCONNECT

6-Information

-

ONEP session has been reconnected after being disconnected temporarly. This disconnect can happen due to intermittent network connectivity issues.

SRVNAME_ONEP

"No action is required if this is an authorized session."

ONEP_BASE-6-DISCONNECT

6-Information

-

ONEP session has been disconnected. A disconnect can happen when application has finished execution or there was a problem during execution including issue with network transport. If reconnect timer is configured Network Element will wait for application to reconnect within configured time before cleaning up session resources.

SRVNAME_ONEP

"No action is required if it is a expected disconnected. " "Use show tech-support onep to collect logs from Network Element"

HW_API-3-RESILIENCE_NO_HANDLER

3-Error

No handlers in place for [chars] sw object creation failure.

COMMON_HW_API_INTERNAL_ERROR

COMMON_HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-INVALID_OBJ

3-Error

Invalid object 0x[hec]

HW_API_INTERNAL_ERROR

HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-INVALID_TYPE

3-Error

Invalid type [dec]

HW_API_INTERNAL_ERROR

HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-INVALID_WALK_SPEC

3-Error

Invalid walk spec 0x[hec]

HW_API_INTERNAL_ERROR

HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-WALK_MODE_UNSUPPORTED

3-Error

Walk mode '[chars]' unsupported

HW_API_INTERNAL_ERROR

HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-INVALID_CONTEXT

3-Error

Invalid context 0x[hec]

HW_API_INTERNAL_ERROR

HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-BACKWALK_REQUEST

3-Error

Backwalk request failed [chars]

A request to walk internal data structures has failed. Depending on criticality of the data accuracy of forwarding may impacted.

COMMON_HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-BACKWALK_REQUEST_VALUE

3-Error

Backwalk request failed [chars] 0x[hec]

-

-

-

HW_API-3-VECTOR

3-Error

Failed to set [chars] vector for [chars] [chars]

HW_API_INTERNAL_ERROR

COMMON_HW_API_DDTS_COMPONENT

LOG_STD_ACTION

HW_API-3-NO_OBJ_TYPE_LIST_ENTRY

3-Error

Invalid sw_obj_type [dec] used with obj_type_list

-

-

-

HW_API-3-NO_OBJ_TYPE_LIST_ENTRY2

3-Error

Invalid sw_obj_link_type [dec] used with obj_type_list

-

-

-

HW_API-3-INIT_FAIL

3-Error

HW-API init [chars] failed[chars]

HW_API_INTERNAL_ERROR

HW_API_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_SADR-3-FIBSADRDEPDUMP

3-Error

[chars]

COMMON_SADR_INTERNAL_ERROR

COMMON_SADR_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_SADR-3-DEPENDENCY_WALK

3-Error

Walk specification %p missing handler for type [dec] dependency

COMMON_SADR_INTERNAL_ERROR

COMMON_SADR_DDTS_COMPONENT

LOG_STD_ACTION

FIB-2-IDBQINIT

2-Critical

Error initializing CEF IDB queue

Initialization of the CEF IDB queue could not be accomplished because of a low memory condition.

IPV4FIB_DDTS_COMPONENT

"Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

FIB-2-LINECARDINIT

2-Critical

Error initializing CEF Linecard queue

Initialization of the CEF linecard queue could not be accomplished because of a low memory condition.

IPV4FIB_DDTS_COMPONENT

"Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

FIB-2-XDRINIT

2-Critical

Error initializing CEF xdr chunks

Initialization of the CEF xdr chunks could not be accomplished because of a low memory condition.

IPV4FIB_DDTS_COMPONENT

"Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

FIB-2-FIBFEATSESINIT

2-Critical

Error initializing CEF repop feature session queue

Initialization of a CEF feature session queue could not be accomplished because of a low memory condition.

IPV4FIB_DDTS_COMPONENT

"Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

FIB-2-DFIBSWITCH

2-Critical

Error trying to turn on Distributed CEF without CEF on

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-FIBXDRLEN

3-Error

Invalid XDR length. Type [dec][chars]. XDR/buffer len [dec]/[dec]

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-FIBBADXDRSLOT

3-Error

Invalid XDR slot. Type/len/slot [dec]/[dec]/[chars]. XDR at 0x%08x

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-4-FIBSPECIALPREFIX

4-Warning

Invalid Special Prefix Type. Type [dec]

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-4-FIBEVENT

4-Warning

Invalid event. Type [chars] event [dec]

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-4-FIBXDRINV

4-Warning

Invalid format. [chars] [chars] [dec]

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-2-FIBDISABLE

2-Critical

Fatal error slot [chars]: [chars]

An internal software error has occurred because of an IPC problem between the LC and the RP. CEF switching has been disabled on the specified slot.

IPV4FIB_DDTS_COMPONENT

"Enter the <bold>clear cef linecard [slot no]<nobold> command " "then check the status of the line card by entering the " "<bold>show cef linecard<nobold> command. If the status shows " "that the line card is still disabled disable and re-enable DCEF " "and check the status of the line card again. " LOG_STD_RECUR_ACTION

FIB-3-INVALIDSTATE

3-Error

Slot [chars] in invalid transition from [chars] to [chars]

An internal software error ocurred. Linecard is in incorrect state

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-4-FIBLCTUNSEQ

4-Warning

[chars] Error Initializing/Updating Linecard Tunnel Configuration

Configuration of a Tunnel on this linecard may not have been successful because of an internal software error.

IPV4FIB_DDTS_COMPONENT

"Reconfigure the Tunnel concerned. If problem persists copy the message " "exactly as it appears and report it to your technical support " "representative."

FIB-6-FIBLCTUNDELSEQ

6-Information

Update received on a linecard for a deleted tunnel[chars] -

An update was received on a linecard for a tunnel that has already been deleted and the update was ignored.

IPV4FIB_DDTS_COMPONENT

LOG_STD_NO_ACTION

FIB-4-FIBCBLK

4-Warning

Missing cef table for tableid [dec] during [chars] event

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-2-FIBDOWN

2-Critical

CEF has been disabled due to a low memory condition. It can be re-enabled by configuring \ip cef [distributed]\

CEF was disabled because of a low memory condition.

IPV4FIB_DDTS_COMPONENT

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade the RP so that it has more DRAM."

FIB-2-FIB_OVERLENGTH_XDR

2-Critical

Overlength CEF XDR message - len [dec] > [dec] from [chars]

An internal software error occurred preventing the sending of an CEF XDR message.

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-FIBSBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified CEF subblock data structure could not be accomplished.

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-FIBSBNOFN

3-Error

Missing [chars] subblock [chars] function for [chars]

Functions for distributing this subblock are missing from the image.

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-FIBPENDINGLIST

3-Error

Error queueing interface [chars] to CEF pending event list.

Queueing an interface to the CEF pending up event list failed

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-MAC_ACCT

3-Error

[chars]: [chars]

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

FIB-3-PREC_ACCT

3-Error

[chars]: [chars]

IPV4FIB_INTERNAL_ERROR

IPV4FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3- NOMEM

3-Error

Memory allocation failure for [chars] in [chars] CEF [0x%08x] [chars][chars].

-

-

-

COMMON_FIB-4- UNEQUAL

4-Warning

Ratio of unequal path weightings [chars] prevents oce [chars] from being used.

-

-

-

COMMON_FIB-3- ILLEGALARGS

3-Error

Illegal arguments - [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-ILIST_OP

3-Error

Manipulating interest list - [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NOBROKER

3-Error

[chars] distribution broker not found - distributing [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-BROKER_ENCODE

3-Error

[chars] broker failed to encode msg type [dec] for slots [chars]

-

-

-

COMMON_FIB-3-FIBXDRINV

3-Error

Invalid XDR format. [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBXDRLEN

3-Error

Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec]

-

-

-

COMMON_FIB-3-FIBXDRCLIENT

3-Error

FIB XDR Client error detected invalid wkid: [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-LCPREFIXINCONST1

4-Warning

Slot [chars] missing prefix entry for [chars] in FIB table [chars] when looking up [chars] [[chars]]

A packet arrived on the linecard but the lookup of the destination IP address failed to find this prefix in the forwarding table. However the prefix is present on the RP. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the CEF prefix on the " "RP and linecard. If necessary a clear cef linecard <slot> " "will download a new CEF table to the linecard. You can also " "try a clear adjacency command to reload host prefixes."

COMMON_FIB-4-LCPREFIXINCONST2

4-Warning

Slot [chars] prefix entry for [chars]/[dec] in FIB table [chars] [[chars]] reason: [chars]

A passive consistency checker discovered a prefix that is present on the RP but is inconsistent in the forwarding table of the linecard. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the CEF prefix on the " "RP and linecard. If necessary a clear cef linecard <slot> " "will download a new CEF table to the linecard. You can also " "try a clear adjacency command to reload host prefixes."

COMMON_FIB-4-RPPREFIXINCONST1

4-Warning

RP prefix for [chars]/[dec] in FIB table [chars] inconsistent on slot [chars] - [chars] [[chars]]

-

-

-

COMMON_FIB-4-RPPREFIXINCONST2

4-Warning

RP missing prefix for [inet]%m in FIB table [chars] present in routing table [[chars]]

A passive consistency checker discovered a prefix in the routing table which is not present in the CEF forwarding table on the RP. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing."

COMMON_FIB-4-RPPREFIXINCONST3

4-Warning

RP has prefix [chars]/[dec] in FIB table [chars] missing in routing table

A passive consistency checker discovered a prefix in the CEF forwarding table which is not present in the routing table. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing."

COMMON_FIB-4-HWPREFIXINCONST1

4-Warning

Hardware on RP missing prefix for [chars]/[dec] in FIB table [chars] present in RP FIB [[chars]]

A passive consistency checker discovered a prefix in the RP FIB table which is not present in the hardware forwarding table on the RP. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing."

COMMON_FIB-4-HWPREFIXINCONST2

4-Warning

Hardware in slot [chars] missing prefix for [chars]/[dec] in FIB table [chars] present in LC FIB [[chars]]

A passive consistency checker discovered a prefix in the LC FIB table which is not present in the hardware forwarding table on this linecard. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing."

COMMON_FIB-4-HWPREFIXINCONST3

4-Warning

RP missing prefix for [chars]/[dec] in FIB table [chars] present in RP hardware [[chars]]

A passive consistency checker discovered a prefix in the hardware table which is not present in the FIB forwarding table on the RP. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing."

COMMON_FIB-4-HWPREFIXINCONST4

4-Warning

Slot [chars] missing prefix for [chars]/[dec] in FIB table [chars] present in LC hardware [[chars]]

A passive consistency checker discovered a prefix in the LC hardware table which is not present in the FIB forwarding table on this linecard. This may be a transient condition.

COMMON_FIB_DDTS_COMPONENT

"If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing."

COMMON_FIB-4-AUTOREPAIR

4-Warning

CEF [chars] database auto-repair executed

The CEF consistency checkers have detected an inconsistent prefix in one of the CEF forwarding databases. The auto-repair function has been executed to repair the problem. Details of the prefix can be found using the 'show cef table consistency' command.

COMMON_FIB_DDTS_COMPONENT

"Copy the message exactly as it appears together with the output of " "the 'show cef table consistency' command and report it to your " "technical support representative"

COMMON_FIB-3-TABLE

3-Error

[chars]: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_GSB

3-Error

Generic subblock error: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_GSB2

3-Error

Generic subblock error: [chars][chars][chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-6-FIB_GSB_TEST_MSG

6-Information

Test subblock error: [chars]

The subblock test command could not be completed successfully

COMMON_FIB_DDTS_COMPONENT

LOG_STD_NO_ACTION

COMMON_FIB-3-FIB_ATTACHED_EXPORT

3-Error

Attached export tracking error: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_FIB_SOURCE

3-Error

[chars] for [chars] - [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_FIB_SOURCE_NULL_FIBIDB

3-Error

[chars] NULL fibidb in broadcast sb

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_FIB_SOURCE_IPL_SB

3-Error

[chars] - [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-6- FIB_RECURSION

6-Information

[chars] has too many [dec] levels of recursion during [chars]

-

-

-

COMMON_FIB-4-BADXDRHWSBDECODE

4-Warning

HW subblock decode [chars] / [dec] - wrong length read expected [dec] decoded [dec]

-

-

-

COMMON_FIB-4-BADXDRSWSBDECODE

4-Warning

SW subblock decode [chars] / [dec] - wrong length read expected [dec] decoded [dec]

-

-

-

COMMON_FIB-3-SBWITHOUTISSUSUPPORT

3-Error

[chars] [chars] subblock doesn't support ISSU and can't be used.

The given SW subblock doesn't support ISSU so may not be processed correctly on the LC. It has not been registered by the CEF component.

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-ILLEGAL_MSG_TYPE

3-Error

Cannot find ISSU message type for FIB [chars] [dec] [chars]SB [chars] msg

-

-

-

COMMON_FIB-4-FIBIDB

4-Warning

No fibidb found for [chars] during [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIBHWIDB

4-Warning

No fibhwidb for [chars] found during [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIBXDR_REGISTRATION

4-Warning

Unable to register XDR client [chars].

-

-

-

COMMON_FIB-3-ASSERT

3-Error

Assertion '[chars]' failed in [chars] CEF [0x%08x]: [chars] [chars][chars].

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-ASSERT_RL

3-Error

Assertion '[chars]' failed in [chars] CEF [0x%08x]: [chars] [chars][chars].

-

-

-

COMMON_FIB-4-DISABLING

4-Warning

[chars] CEF is being disabled due to a fatal error.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-DEPENDENCY_WALK

3-Error

Walk specification %p missing handler for type [dec] dependency

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-DEPENDENCY_CHAIN

3-Error

Missing handler for type [dec] dependency

COMMON_FIB_INTERNAL_ERROR

OCE_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBDEPDUMP

3-Error

[chars]

COMMON_FIB_INTERNAL_ERROR

OCE_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBPLDEPDUMP

3-Error

[chars]

COMMON_FIB_INTERNAL_ERROR

OCE_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBCOVEREDDEPDUMP

3-Error

[chars] [chars]

COMMON_FIB_INTERNAL_ERROR

OCE_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBLBCLPSECHAINDEPDUMP

3-Error

[chars]

COMMON_FIB_INTERNAL_ERROR

OCE_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_OCC_DEP_DUMP

3-Error

[chars]

COMMON_FIB_INTERNAL_ERROR

OCE_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIB_OCC_SB_REMOVE_FAIL

4-Warning

Attempted to remove subblock of type '[chars]' [dec] for [chars] failed

-

-

-

COMMON_FIB-4-BROKERINVMSG

4-Warning

Invalid message: [chars] type [chars] len [dec]

An invalid message has been received by this broker.

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-ISSUBUFFERTOOSHORTMSG

4-Warning

Message [chars] for slots [chars] is too large [dec] bytes max [dec]

-

-

-

COMMON_FIB-4-ISSUENCODEWRONGLEN

4-Warning

Message [chars] for slots [chars] is wrong length [dec] should be [dec]

-

-

-

COMMON_FIB-3-SBNOTISSUAWARE

3-Error

Subblock [chars] is not ISSU aware and should be!

ALL FIB subblocks must be ISSU aware. The subblock code must be rewritten for ISSU. Otherwise this may lead to unpredictable behaviour when running in SSO mode with two different versions of IOS.

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-MSGISSUAWARE

3-Error

Message [chars] [dec] is ISSU aware so cannot use old FIB API.

ALL FIB subblocks must be ISSU aware. The subblock code must be rewritten for ISSU. Otherwise this may lead to unpredictable behaviour when running in SSO mode with two different versions of IOS.

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-SB_STAT_ENCODE

4-Warning

Encoding of [chars] [chars] stats XDR too big

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-CHAIN_INSERT_INCONS1

4-Warning

Attempting to insert %p after %p but it is still pointed at by %p

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-CHAIN_INSERT_INCONS2

4-Warning

Attempting to insert %p after %p but it has prev set to %p

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-CHAIN_REMOVE_INCONS1

4-Warning

Attempting to remove %p but prev %p points at %p instead

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-CHAIN_REMOVE_INCONS2

4-Warning

Attempting to remove %p but it has no prev next is %p

-

-

-

COMMON_FIB-4-CHAIN_REMOVE_INCONS3

4-Warning

Attempting to remove %p with next %p thinks its prev is %p

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-CHAIN_BAD_MAGIC

3-Error

Bad magic for element %p 0x%08x != 0x%08x

-

-

-

COMMON_FIB-3-DQUEUE_BAD_PREV

3-Error

elem %p type 0x[hec] elem->prev %p elem->prev_type 0x[hec] elem->prev->next %p

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-DQUEUE_BAD_NEXT

3-Error

elem %p type 0x[hec] elem->next %p elem->next_type 0x[hec] elem->next->prev %p

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDB_DB_MEM

3-Error

[chars] chunk pool could not be [chars]. Possible memory leak.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDB_DB_INTERNAL

3-Error

fibidb [chars] if_nb [dec] could not be [chars] db

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDB_DB_NULL_FIBIDB

3-Error

API called with NULL fibidb

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-EPOCH

3-Error

Failed to start [chars] of [chars]entries in table [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-IPMFI_TIMING_PRESENT

3-Error

IPMFI Timing Tool present in image - performance will be degraded

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIBMSG

4-Warning

Invalid message received. Type [chars] event/sub-type [dec] length [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-ILLEGAL_TABLEID

3-Error

Attempt to create [chars] table with illegal tableid [dec] [chars]:[chars]

-

-

-

COMMON_FIB-3-NO_TABLE_NAME

3-Error

Attempt to clear the name of [chars] table with tableid [dec] previous name [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-2-FIBTABLEILLEGAL

2-Critical

Attempt to used uninitialized CEF data structure.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDBEARLYCALL

3-Error

Attempt to update fibidb prior to completion of idb initialization.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-2-IFINDEXBOUNDS

2-Critical

Attempt to use out of bounds interface index: [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-2-HW_IF_INDEX_ILLEGAL

2-Critical

Attempt to create CEF interface for [chars] with illegal index: [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-2-IF_NUMBER_ILLEGAL

2-Critical

Attempt to create CEF interface for [chars] with illegal if_number: [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDBINCONS1

3-Error

An internal software error occurred. [chars] should be first fibidb

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDBINCONS2

3-Error

An internal software error occurred. [chars] linked to wrong idb [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBHWIDBINCONS

3-Error

An internal software error occurred. [chars] linked to wrong hwidb [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIBIDBMISMATCH

4-Warning

Mis-match between idb [chars] if_number [dec] and fibidb [chars] if_number [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIBHWIDBMISMATCH

4-Warning

Mis-match between hwidb [chars] ifindex [dec] and fibhwidb [chars] ifindex [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-4-FIBNULLIDB

4-Warning

Missing idb for fibidb [chars] if_number [dec].

-

-

-

COMMON_FIB-4-FIBNULLHWIDB

4-Warning

Missing hwidb for fibhwidb [chars] ifindex [dec]

-

-

-

COMMON_FIB-4-FIBMISSINGHWIDB

4-Warning

No fibhwidb while initializing fibidb for [chars] if_number [dec]

-

-

-

COMMON_FIB-3-HW_API

3-Error

HW API failure for [chars] CEF [0x%08x]: [chars] [chars][chars].

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-TABLE_CONCURRENT_UPDATE

3-Error

[chars]: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBTOPO

3-Error

Error for topology [dec]: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBTOPOSTAT

3-Error

Error pulling topology stats [chars][chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_MPLS_EXT_FIND_OCE

3-Error

Unable to find MPLS oce for [chars] IP oce

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-INVALID_AF

3-Error

Invalid address family [dec][chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBIDBNONBASETABLE

3-Error

interface [chars] being set with non-base table: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-DQUEUE_ACTIVE_COLLECTION

3-Error

dqueue has an active collection just prior to destruction

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-INVALID_ADDR_TYPE

3-Error

Invalid address type [dec][chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-DQUEUE_NON_EMPTY

3-Error

dqueue is not empty just prior to destruction

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBHWIDB_NONAME

3-Error

Missing name for fibhwidb ifindex [dec]

-

-

-

COMMON_FIB-3-FIBSUBTREECONTEXT

3-Error

Subtree context unexpected error: app [chars]: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NOHWSBDECODE

3-Error

No [chars] subblock control decode function for [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NOSWSBDECODE

3-Error

No [chars] subblock control decode function for [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NOLABELNOLABEL

3-Error

Unexpected disposition information for [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NOPATHFIBIDB

3-Error

No fibidb for [chars] ignoring path during path no [dec] update for [chars]

-

-

-

COMMON_FIB-4-TOPO_STAT_ID_MGR

4-Warning

Id manager error [chars]. Topology statistics accounting may not show the correct result

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-UNHANDLED_UNITS

3-Error

No handler for units [chars] - from slot [chars]

-

-

-

COMMON_FIB-3-NAMETOOLONG

3-Error

FIB[chars]IDB name [chars] error lengths [dec] [dec] short [dec] [dec]

-

-

-

COMMON_FIB-4-FIB_SB_ADD_FAIL

4-Warning

Attempted add of subblock of type '[chars]' [dec] for [chars] failed[chars]

-

-

-

COMMON_FIB-3-FIB_LOADBALANCE_MAP

3-Error

[chars] map [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_LOADBALANCE_MAP_NO_USEABLE_CHOICES

3-Error

No useable choices %04x bucket count [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_LOADBALANCE_USAGE

3-Error

Unhandled usage flag 0x[hec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_PATH_LIST_DB

3-Error

[chars] path list [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NO_VALID_PATHS

3-Error

No valid paths for prefix [chars] in vrf [chars].

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-DQUEUE_BAD_ELEM

3-Error

Unexpected element type [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-VRFID_INVALID

3-Error

Error invalid vrfid [chars][chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-ACL_PBR_NAMETOOLONG

3-Error

IPV6_SWSB_CTRL name length error [chars] acl_in [dec] [dec]

IPv6 in/out ACL and IPv6 PBR name lengths for/from an IPC XDR message are invalid. The names will not be used so as to prevent any buffer overrun errors. There is a possibility that either the XDR message or an internal IPv6 FIB structure is corrupted

IPV6FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-BFD_SESS

3-Error

[chars]:[chars] failed to [chars] BFD session error [[chars]]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-BFD

3-Error

[chars][chars][chars][chars][chars][chars][chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-NOSUCHCAPTURE

3-Error

Error finding capture point.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIBTABLE

3-Error

Error for table [dec]: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-VRFMGR_INVALID

3-Error

Error invalid [chars] [dec]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_NON_IP_ENTRY_INCR

3-Error

[chars] non-ip entry 0x%08x path list [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-PATH_EXT_ENCODE

3-Error

Failed to encode [chars] path extension [chars]

One or more path extensions could not be encoded for distribution and will not be sent. This indicates an internal code error and may impact CEF operation for prefixes using the affected path extensions.

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-PATH_INVALID_REPAIR

3-Error

Primary or repair paths configured by RIB are of invalid type: primary: [chars] repair: [chars]

Either the primary path or the repair path is not of the correct type i.e. an attached nexthop that provides both interface and nexthop

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-ISSU_REG

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

ISSU negotiation failed for this XDR client.

COMMON_FIB_DDTS_COMPONENT

"This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it."

COMMON_FIB-3- ISSU_ENUM_ERROR

3-Error

Enum for [chars] is not ISSU-compliant: [chars]

The given enumeration is not ISSU-compliant for the reason given. Unpredictable behaviour will result when interoperating with different IOS versions.

COMMON_FIB_DDTS_COMPONENT

"This requires a code fix before the image can be shipped or ISSU will be " "broken."

COMMON_FIB-3- FIBINVPEXTLEN

3-Error

[chars] ext attempt to decode beyond XDR buffer cp_cur 0x[hec] cp_end 0x[hec] num_ext [dec] curr_ext_idx [dec]

The path extension decode logic is trying to access memory beyond XDR buffer which can lead to memory corruption.

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-PATH_EXT_ISSU_SR_LDP

3-Error

Dowgrading to a version that doesn't support Segment Routing and LDP on the same path labels [[dec]|[dec]].

This indicates there's an issue in ISSU transformation when downgrading to a lower version. Configuration changes might be required to avoid this issue. See recommended action.

COMMON_FIB_DDTS_COMPONENT

"Find out the prefix which is using the two outgoing " "labels as shown in the message with 'show mpls forwarding-table'. Check " "IGP configuration and disable either LDP or SR on that prefix."

COMMON_FIB-4- MAX_PATHS_EXCEEDED

4-Warning

Prefix [chars] in vrf [chars] has paths in excess of the maximum. Some may be dropped.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3- PATH_EXT_DUPLICATE

3-Error

Detected identical [chars] path extension [chars] ext %p - replacing.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3- PATH_EXT_PLIST_CHG_DUP_SHORT

3-Error

Detected identical short path extension following path list change idx [dec] type [dec] [[chars] --> [chars]] conv [dec] renum [dec] total short [dec] ext list %p.

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-FIB_XDR_BUF_OVERFLOW

3-Error

FIB XDR buffer overflow while encoding [chars] [[chars]]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-5-FIB_RRP_HEADLESS_MODE

5-Notice

%S

The RRP lost communication with the RP but the platform still wants CEF\n\ to continue operating in headless mode.

-

LOG_STD_ACTION

COMMON_FIB-3-FIB_ADJ_LINKTYPE

3-Error

OCE chain for [chars] terminates with [chars] linktype is [chars] not [chars]

An OCE chain for a FIB entry terminates with a linktype other than what was expected. This will cause encapsulation problems in the dataplane.

COMMON_FIB_DDTS_COMPONENT

"Get the full show ip[v6] cef <vrf prefix> internal" " output of the affected FIB entry and determine" " if anything looks wrong. For instance is a label" " or a midchain adjacency missing?"

COMMON_FIB-3-BINDINGLABEL

3-Error

Binding label [chars]: [chars]

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_FIB-3-LOADBALANCE_LOOP

3-Error

Detected loop while installing OCE: [chars] %p to loadinfo: [chars] %p

COMMON_FIB_INTERNAL_ERROR

COMMON_FIB_DDTS_COMPONENT

LOG_STD_ACTION

IPV6FIB-4-FIBIDB

4-Warning

Missing cef idb for [chars] during [chars]

IPV6FIB_INTERNAL_ERROR

IPV6FIB_DDTS_COMPONENT

LOG_STD_ACTION

IPV6FIB-4-FIBCBLK

4-Warning

Missing cef table for tableid %lu during [chars] event

IPV6FIB_INTERNAL_ERROR

IPV6FIB_DDTS_COMPONENT

LOG_STD_ACTION

IPV6FIB-4-FIBXDRINV

4-Warning

Invalid format. [chars]

IPV6FIB_INTERNAL_ERROR

IPV6FIB_DDTS_COMPONENT

LOG_STD_ACTION

IPV6FIB-4-FIBXDRLEN

4-Warning

Invalid XDR length. Type/event [dec]/[chars]. XDR [dec] buffer [dec]

IPV6FIB_INTERNAL_ERROR

IPV6FIB_DDTS_COMPONENT

LOG_STD_ACTION

IPV6FIB-3-GLOBALSTATE

3-Error

Inconsistent global state '[chars]' [chars]

IPV6FIB_INTERNAL_ERROR

IPV6FIB_DDTS_COMPONENT

LOG_STD_ACTION

COLLECTION-3-MODE_PRIORITY_MISMATCH

3-Error

Attempted to start a walk with incompatible mode and priority mode [chars] priority [chars]

COLLECTION_INTERNAL_ERROR

COLLECTION_DDTS_COMPONENT

LOG_STD_ACTION

COLLECTION-3-MODE_PROCESS_MISMATCH

3-Error

Attempted to start a walk with incompatible mode and process mode [chars] process [chars]

COLLECTION_INTERNAL_ERROR

COLLECTION_DDTS_COMPONENT

LOG_STD_ACTION

COLLECTION-3-SUB_WALK

3-Error

Subwalk mismatch walk %p priority [chars] mode [chars]

COLLECTION_INTERNAL_ERROR

COLLECTION_DDTS_COMPONENT

LOG_STD_ACTION

COLLECTION-3-PROC_INIT

3-Error

Initialization of process [chars] failed unable to [chars]

COLLECTION_INTERNAL_ERROR

COLLECTION_DDTS_COMPONENT

LOG_STD_ACTION

COMMON_TAL-3- HOSTBITSSET

3-Error

Host bits set for [chars]/[dec].

TAL API has been called with prefix/len pair with host bits set. This prefix/len pair is invalid and indicates an error in the calling code.

COMMON_TAL_DDTS_COMPONENT

"Copy the message exactly as it appears and report it " "to your technical support representative."

GENERIC_SUBBLOCK-2-LATE_REGISTER

2-Critical

Late registration of GSB type [chars] with id [dec]

An attempt to register a new generic subblock type was received after subblocks have already been allocated from the control structure with previously registered types

-

LOG_STD_ACTION

GENERIC_SUBBLOCK-2-BUILDXDR

2-Critical

Failed to build message for GSB: [chars]

An attempt to build a message for distribution of generic subblock failed

-

LOG_STD_ACTION

GENERIC_SUBBLOCK-2-UNPACKXDR

2-Critical

Unpacked [dec] bytes and attempted to consume [dec] bytes for GSB: [chars]

A discrepancy was detected between length of message expected versus length of message received

-

LOG_STD_ACTION

GENERIC_SUBBLOCK-2-GSBNOTISSUAWARE

2-Critical

GSB [chars] is not ISSU aware. Cannot distribute it to ISSU-aware slots

This GSB is expected to be ISSU aware but it is not. It cannot be distributed safely to ISSU-aware slots as it may not be correctly interpreted

-

LOG_STD_ACTION

CFC_STATS-3- BADSTATSPULL

3-Error

[chars]: [chars]

Internal error. May result in unpredictable behaviour.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-3- BADSTATSCLIENTSEND

3-Error

[chars]: [chars] 0x%08X/[dec] expected 0x%08X/[dec]

Internal error. May result in unpredictable behaviour.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-4- BADSTATSCLIENTRECEIVE

4-Warning

context [dec] length [dec] from [chars]

The XDR statistics infrastructure received a message it could not decode from a peer. This has no harmful effects but might be a evidence of a more serious problem.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-4- STATSUNEXPECTEDNEWMCASTGRP

4-Warning

Add req for [chars] but already sending stats to [chars]

The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-4- STATSUNEXPECTEDEVENT

4-Warning

[chars]

The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-4- STATSCLIENTADDMCASTGRPFAIL

4-Warning

Stats client [chars] failed to add linecards [chars]

The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-4-STATSCLIENT_REGISTRATION

4-Warning

Unable to register XDR client [chars] client due to [chars]

The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-3-TESTSTATSCLIENT_DECODE

3-Error

XDR test stats [chars] saw error [chars].

-

-

-

CFC_STATS-3-TESTSTATSCLIENT_UNEXPECTED_EVENT

3-Error

Selftest failure: unexpected event [hec] [hec] during

The XDR statistics infrastructure has experienced a self test failure. This should only occur when a self test is running and a failure is detected. It does not directly imply a problem with normal operation.

-

"Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_STATS-3- STATSNOMEM

3-Error

CFC Stats failed to allocate memory during [chars] creation.

Allocation of memory by the XDR subsystem failed. This may result in an unpredictable behavior of XDR

-

"Make sure that there is enough memory for the operations being performed " "by your machine. " "Copy the message exactly as it appears and report it to your technical " "support representative."

CFC_LISP-3-ALLOCATEFAIL

3-Error

Failed to allocate memory for [chars]

An internal software error occurred. This is probably because not enough memory was available.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-SB_OPERATION_FAILED

3-Error

Failed to [chars] subblock on [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-LOCAL_EID

3-Error

Failed to [chars] local EID prefix [chars]/[dec]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-REMOTE_EID

3-Error

Failed to [chars] remote EID prefix [chars]/[dec][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-REMOTE_EID_PREFIX

3-Error

Failed to [chars] remote EID prefix [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-NO_ADJ

3-Error

Failed to find adjacency for [chars] [chars] [chars] [dec]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-NO_FIBIDB

3-Error

Failed to find fibidb for [chars] [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-NO_SB

3-Error

Failed to find subblock for [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-NO_TABLE

3-Error

Failed to find table for [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-BG_PROCESS

3-Error

Background process failed to [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-TABLE_STATE

3-Error

Error setting state for table [chars] to top-id [dec] iid [dec] role [chars] [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-TABLE_BIND

3-Error

Error setting [chars] table [chars] for top-id [dec] iid [dec] [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-TREE_OP_FAIL

3-Error

Tree [chars] failed for [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-VIF

3-Error

Unable to [chars] virtual interface [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-ADJ_SEQ

3-Error

Adjacency [chars] is still complete after interface shutdown

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-NO_VIF

3-Error

Unable to find [chars]virtual interface [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-UNABLE_TO_IDENTIFY_TABLE

3-Error

Unable to identify table for packet from [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-INVALID_INPUT

3-Error

Invalid input [chars] to [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-RLOC_VRF_IN_USE

3-Error

RLOC vrfid [dec] already in use by user [chars] top-id [dec] cannot assign to top-id [dec]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-UNEXPECTED_PKT

3-Error

[chars]: 0x%08x

A packet with an unexpected protocol was given to the LISP datapath.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-UNKNOWN_PAYLOAD

3-Error

Dropping LISP encapsulated packet unknown payload 0x%08x

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-5-IGNOREICMPMTU

5-Notice

Ignoring received ICMP Type 3 Code 4 [chars]->[chars] next hop mtu [dec] due to pmtu min or max setting

An ICMP Type 3 Code 4 fragmentation needed and DF set packet

CFC_LISP_MSG_DDTS_COMP

"If you want the ICMP packet to be accepted and used " "use the <CmdBold> ip lisp pmtu min NUMBER max NUMBER <NoCmdBold> " "command to decrease the minimum MTU allowed and/or increase the " "maximum MTU that is allowed."

CFC_LISP-5-IGNOREICMPV6MTU

5-Notice

Ignoring received ICMPv6 Type 2 [chars]->[chars] next hop mtu [dec] due to pmtu min or max setting

An ICMPv6 Type 2 Packet Too Big packet

CFC_LISP_MSG_DDTS_COMP

"If you want the ICMP packet to be accepted and used " "use the <CmdBold> ipv6 lisp pmtu min NUMBER max NUMBER <NoCmdBold> " "command to decrease the minimum MTU allowed and/or increase the " "maximum MTU that is allowed."

CFC_LISP-3-IPL_SRC

3-Error

Failed to [chars] IPL source [chars] [chars]/[dec][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-PUSH_CNTR

3-Error

Failed to [chars] push counter for [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-ELIG_OCE

3-Error

Failed to [chars] LISP eligibility oce [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-DECAP_OCE

3-Error

Failed to [chars] LISP decapsulation OCE: [chars][chars]

An operation dealing with a LISP decapsulation OCE encountered an error. The error message will indicate which operation failed and the address-family context.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-SIGNAL_OCE

3-Error

Failed to [chars] LISP signal OCE [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-TIMESTAMP_CTRL_PKT

3-Error

Failed to timestamp LISP control packet

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-FREE_WITH_DEPS

3-Error

Request to remove dependency sb on [chars] with dependents

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-DEP_ELEM

3-Error

Request to [chars] dependency [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-ADJ

3-Error

Request to [chars] adjacency [chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-5-ADJ_STACK

5-Notice

Stacking adjacency [chars] [chars][chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-XDR_REG_ERR

3-Error

Failed to register XDR client [chars] [dec] error [chars]

-

-

-

CFC_LISP-3-XDR_LEN_ERR

3-Error

Failed to [chars] XDR message [chars] len [dec] > max [dec]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-ISSU_REG_ERR

3-Error

Failed to register [chars] for ISSU client [chars] [dec] entity [dec] error [chars]

-

-

-

CFC_LISP-3-ISSU_NEGO_ERR

3-Error

Failed to negotiate [chars] for XDR client [chars] error [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-ISSU_XFORM_ERR

3-Error

Failed to ISSU transform XDR message [chars] error [chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-UNKN_INSTANCE

3-Error

Unknown instance unable to find/create virtual interface

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-WALK_DEP

3-Error

Walking dependents [chars][chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-TERM_ADJ

3-Error

Terminal adjacency [chars][chars][chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-5-BELOW_MIN_MTU

5-Notice

Cannot set [chars] MTU for RLOC [chars] to [dec] [chars] MTU for [chars] [chars] is [dec] below minimum MTU [dec]+[dec] required for LISP encap

Unable to set the EID payload MTU for a remote RLOC below the minimal MTU this will cause the encapsulated packet to be bigger than the MTU of the path to the remote RLOC and may cause packet loss.

CFC_LISP_MSG_DDTS_COMP

"Increase the MTU of the path to the remote RLOC"

CFC_LISP-3-DEPRECATED_API

3-Error

Use of a deprecated API [chars][chars]

-

CFC_LISP_MSG_DDTS_COMP

"Increase the MTU of the path to the remote RLOC"

CFC_LISP-3-UNEXPECTED_PATH

3-Error

Unexpected path type [chars]/[dec]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-NO_PATH

3-Error

Failed to resolve path type for [chars]:[chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-SRC_RLOC_IDX

3-Error

[chars] source RLOC index database[chars]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-GSMR

3-Error

Failed to [chars] generalised SMR attribute for [chars]/[dec]

An internal software error occurred.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

CFC_LISP-3-DYN_EID_IP_ADDR_CONFLICT

3-Error

Ignore dynamic EID detection due to IP Address conflict [chars]:[chars] on [chars]

A dynamic EID Host attempted to register with an IP address conflicting with the XTR gateway. Refer to error message log for more details.

CFC_LISP_MSG_DDTS_COMP

LOG_STD_ACTION

LSD_CLIENT-3-UTIL2

3-Error

[chars]: [hec] [hec]

MFI Utilities error occurred

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-3-PCHUNK2

3-Error

[chars]: [chars] [hec] [hec]

Parameterized Chunk Manager error occurred

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "<CmdBold>show running-config<NoCmdBold> and <CmdBold>show process memory<NoCmdBold> " "and contact your Cisco technical support representative."

LSD_CLIENT-2-MSGHANDLERERR

2-Critical

Client=[dec] Msg type=[dec] Error=[chars]

LSD Client API message handler error encountered

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-3-CLIENTAPI

3-Error

Client API error: [chars] [dec]

Unexpected Client API error

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-3-INVALID_VAR

3-Error

[chars]

Function received invalid parameters

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-2-XDREXEC

2-Critical

[chars] [dec]

Illegal code execution in XDR path

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-2-XDREXEC2

2-Critical

[chars] [hec] [hec]

Illegal code execution in XDR path

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-3-ISSU_MSG_CONV

3-Error

[chars] [dec] [dec]

Could not convert received message type to known message

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

LSD_CLIENT-3-ISSU_REG

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

ISSU negotiation failed for this XDR client.

mpls-mfi

"This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it."

LSD_CLIENT-3-ISSU_ENUM_ERROR

3-Error

Enum for [chars] is not ISSU-compliant: [chars]

The given enumeration is not ISSU-compliant for the reason given. Unpredictable behaviour will result when interoperating with different IOS versions.

mpls-mfi

"This requires a code fix before the image can be shipped or ISSU will be " "broken."

MPLS_PACKET-3-FWDDISABLE

3-Error

MPLS [chars] forwarding path disabled

MPLS forwarding plane disabled

mpls-mfi

"This log entry is informational only."

MPLS_PACKET-3-FWDREENABLE

3-Error

MPLS [chars] forwarding path reenabled

MPLS forwarding plane reenabled

mpls-mfi

"This log entry is informational only."

MPLS_PACKET-4-NOLFDSB

4-Warning

MPLS packet received on non MPLS enabled interface [chars] L3 type 0x%04x label {[dec] [dec] [dec] [dec]}

MPLS packets received on an interface are being dropped as the interface is not setup to handle MPLS. This message may be seen when a mpls application is disabled on a interface and should go away when the upstream neighbor has reprogrammed its cef/mpls entries.

mpls-mfi

"If a MPLS application has just be disabled and traffic is flowing" "then the message is expected and should be ignored." "If the message recurs in steady state the operator should monitor" "the network for attacks and report the occurence to Cisco."

MPLS_PACKET-3-LABELCACHE

3-Error

[chars] [dec]/[dec]

label cache error

mpls-mfi

LOG_STD_ACTION

MPLS_PACKET-3-WRONGIDB

3-Error

MPLS packet input sub interface hwidb [chars] does not match with

Internal software error occurred

mpls-mfi

LOG_STD_ACTION

MPLS_ADJ_SB-4-NO_BACKUP_INTF

4-Warning

[chars] - ifnum [dec]

Backup interface cannot be programmed

mpls-mfi

LOG_STD_ACTION

MPLS_ADJ_SB-4-UNMATCHED_PRO_PATH

4-Warning

[chars] - adj 0x[hec]

MFI adj_sb uses unmatched protect lsp from CEF adj parent

mpls-mfi

LOG_STD_ACTION

MPLS_ADJ_SB-4-PATH_PRO_CUTOVER

4-Warning

[chars] - adj 0x[hec] sb 0x[hec]

MFI adj or adj_sb error during path protection cutover

mpls-mfi

LOG_STD_ACTION

MPLS_ADJ_SB-4-MULTI_LABEL_STACK

4-Warning

[chars] - slot [chars]

Multi-Label Stack not supported on Peers

mpls-mfi

LOG_STD_ACTION

MPLS_ADJ_SB-4-MPLS_ADJ_SB_ECMP

4-Warning

[chars] - slot [chars]

MPLS ADJ ECMP not supported on Peers

mpls-mfi

LOG_STD_ACTION

MPLS_ADJ_SB-3-MPLS_ADJ_GENERAL

3-Error

[chars]

mpls adj sb error message

mpls-mfi

LOG_STD_ACTION

ATOM_SEG-3-CHUNKFREE

3-Error

Error freeing [chars]

ATOM Segment Handler error

mpls-mfi

LOG_STD_ACTION

ATOM_SEG-3-NOTSUPP

3-Error

Unsupported update [chars]

AToM Segment Handler error

mpls-mfi

LOG_STD_ACTION

ATOM_SEG-3-ILLEGALUPD

3-Error

Illegal label [dec] update [chars]

AToM Segment Handler error

mpls-mfi

LOG_STD_ACTION

ATOM_SEG-3-UNSUPPORTEDADDR

3-Error

Unsupported address type [dec]

AToM Segment Handler error

mpls-mfi

LOG_STD_ACTION

MFI_LABEL_BROKER-3-UNREG_LDM

3-Error

[chars]

An MPLS application requested label broker services without registering first.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-DUPREG_LDM

3-Error

[chars]

An MPLS application is registering multiple times with the label broker.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-INVALID_PROC_EVT

3-Error

[chars][dec][chars][dec]

The MFI Label Broker received an invalid process event from the IOS-on-Neutrino infrastructure.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-INVALID_LDM

3-Error

[dec]

The MFI Label Broker received a unregistration request from an invalid

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-NULL_KEY

3-Error

-

The MFI Label Broker received a null key pointer

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-INVALID_PID

3-Error

LDM[dec] PID[dec]

The MFI Label Broker received a registration request with invalid PID.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-INVALID_LABEL

3-Error

[dec]

The MFI Label Broker received a request to allocate an invalid label.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-INVALID_PARAM

3-Error

[chars]

The MFI Label Broker received an invalid parameter in a request to allocate or free a local label.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-MULTIPLE_BIND

3-Error

Label [dec] in table [dec] [chars] [chars] [p/bm [dec]/0x[hec]]ldm request info: [chars]

The MFI Label Broker received a request to bind the label to a prefix but the label is already bound to another prefix.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> " "<CmdBold>show running-config<NoCmdBold> and " "<CmdBold>show mpls forwarding-table<NoCmdBold> and contact your Cisco" " technical support representative."

MFI_LABEL_BROKER-3-DELETE_MOI_FAIL

3-Error

Label [dec] in table [dec] [chars] [chars]

The MFI Label Broker could not honor a request to immediately handle the process restart of the application indicated. It will try to handle it in the background

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> " "<CmdBold>show running-config<NoCmdBold> and " "<CmdBold>show mpls infrastructure label-broker ldm<NoCmdBold>" " this latter command is present only when" " <CmdBold>service internal<NoCmdBold> is enabled and contact your Cisco"

MFI_LABEL_BROKER-3-IMMEDIATE_LDM_RESTART

3-Error

application [chars]

-

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> and " "<CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MFI_LABEL_BROKER-3-NO_ACTIVE_LABEL

3-Error

[chars] Label [dec] in table [dec] [chars] 0x[hec]

The MFI Label Broker encountered a situation where there is no currently active label for applications to use for the FEC indicated.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> " "<CmdBold>show running-config<NoCmdBold> " "<CmdBold>show mpls forwarding-table internal<NoCmdBold> and contact " "your Cisco technical support representative."

MFI_LABEL_BROKER-3-LABEL_PROGRAM_FAIL

3-Error

Label [dec] in table [dec] for [chars]

The MFI Label Broker was unable to program the label in question for the mentioned FEC.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> " "<CmdBold>show running-config<NoCmdBold> " "<CmdBold>show mpls forwarding-table internal<NoCmdBold> and contact " "your Cisco technical support representative."

MFI_LABEL_BROKER-3-OS_NOTIFY

3-Error

Process id [dec] [chars] error code [dec]

The MFI Label Broker was unable to notify the operating system about unregistration of the specified process.

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> " "<CmdBold>show running-config<NoCmdBold> " "<CmdBold>show mpls infrastructure label-broker ldm<NoCmdBold> and contact " "your Cisco technical support representative."

MPLSMFISTATIC-3-FCALLFAILED

3-Error

[chars]

MPLS MFI Static Application function call return error

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MPLSMFISTATIC-3-INVALIDPRAMS

3-Error

[chars] [dec]

Unexpected MPLS MFI Static Application parameter error

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MPLSMFISTATIC-3-WRONGCODEPATH

3-Error

[chars]

Unexpected MPLS MFI Static Application code path error

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

MPLSMFISTATIC-3-CHUNKMGR

3-Error

[chars] [hec]

MPLS MFI Static Application chunk manager error has occurred.

mpls-mfi

"Problem may be due to a low memory condition on the device. " "Check system memory and minimum memory requirements for this " "release and configuration and add memory if required. If " "memory appears to be sufficient and problem persists refer " "to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. " "If not gather the output of <CmdBold>show process memory<NoCmdBold> <CmdBold>show " "version<NoCmdBold> and <CmdBold>show running-config<NoCmdBold> and contact your Cisco " "technical support representative."

CFC_MPLS_CP_APP_MSG-3-CLIENT_ERR

3-Error

MPLS CP APP Unsupported Client [dec]

Unsupported client trying to use cfc apis

mpls-mfi

LOG_STD_ACTION

CFC_MPLS_CP_ION-3-BATCHERR

3-Error

MPLS CP ION Batch Error [dec] for [chars]

Error in batching ion messages between cfc and mpls clients

mpls-mfi

LOG_STD_ACTION

MFI-3-REDISTMGR

3-Error

Redistribution Manager: [chars] [hec]

Redistribution Manager error

mpls-mfi

LOG_STD_ACTION

MFI-3-REDISTMGR2

3-Error

Redistribution Manager: [chars] [hec] [hec]

Redistribution Manager error

mpls-mfi

LOG_STD_ACTION

MFI-4-REDISTMGR3

4-Warning

Redistribution Manager: [chars] [hec]

Redistribution Manager error

mpls-mfi

LOG_STD_ACTION

MFI-3-EVTLOGCLIENT

3-Error

Invalid client [dec]

Invalid client accessed the Event Logger

mpls-mfi

LOG_STD_ACTION

MFI-3-EVTLOGCAPTURE

3-Error

Event Logger Capture Error [dec] [dec]

Failure during Event Logger capture

mpls-mfi

LOG_STD_ACTION

MFI-3-EVTLOGREGISTER

3-Error

Event Logger Registration Error [dec] [dec] [dec]

Failure during Event Logger client registration

mpls-mfi

LOG_STD_ACTION

MFI-3-REPLYMSGSIZE

3-Error

Reply message is too large: [chars]: [dec]

read update message won't fit into xdr buffer

mpls-mfi

LOG_STD_ACTION

MFI-3-EVTLOGCONTROL

3-Error

[chars]: [dec]

General Event Logger Controller error

mpls-mfi

LOG_STD_ACTION

MFI-3-BADREADUPDATESIZE

3-Error

Read update reply message from RP has bad size: [dec]

read update message does not match the read message parse result

mpls-mfi

LOG_STD_ACTION

MFI-3-PNDMSGMGR

3-Error

[chars] [chars] [dec] [dec] [dec]

Only one outstanding request is allowed from same process

mpls-mfi

LOG_STD_ACTION

MFI-4-NOCLIENTREQ

4-Warning

[chars] [chars]: [dec] [dec] [dec]

Client reply could not find an outstanding request

mpls-mfi

LOG_STD_ACTION

MFI-3-LCPULSE

3-Error

LC pulse failed: [chars] [dec]

LC pulse request operation failed

mpls-mfi

LOG_STD_ACTION

MFI-3-MFICOMM

3-Error

[chars]

MFI General Communication Module

mpls-mfi

LOG_STD_ACTION

MFI-3-MFICOMM2

3-Error

[chars]: [hec] [hec]

MFI General Communication Module

mpls-mfi

LOG_STD_ACTION

MFI-3-MFICOMM3

3-Error

[chars]: [hec] [hec] [hec]

MFI General Communication Module

mpls-mfi

LOG_STD_ACTION

MFI-4-MFICOMM_WARN_1

4-Warning

[chars]: [hec]

MFI General Communication Module

mpls-mfi

LOG_STD_ACTION

MFI-3-CLIENT_INTF

3-Error

[chars]: [hec] [hec]

Client Interface

mpls-mfi

LOG_STD_ACTION

MFI-3-MPLS_MTU_SET

3-Error

[chars] [dec] [chars] [chars] [chars] [dec][chars]

Most drivers will be able to support baby giants and will gracefully drop packets that are too large. Certain drivers will have packet forwarding problems including data corruption.

mpls-mfi

"Please increase the interface mtu on all routers connected " "to this interface to the needed mtu size using <CmdBold>mtu<NoCmdBold> <CmdArg>bytes<NoCmdArg> command. "

LSD-2-RESOURCE

2-Critical

[chars]

System resource error occured

mpls-mfi

LOG_STD_REDUCE_ACTION

LSD-2-INVALID_VAR

2-Critical

[chars]

Function received invalid parameters

mpls-mfi

LOG_STD_ACTION

LSD-4-INVALID_VAR_WARN

4-Warning

[chars]

Function received invalid parameters

mpls-mfi

LOG_STD_ACTION

LSD-4-BADAPI

4-Warning

[chars] from [chars]

LSD recieved message with invalid parameters

mpls-mfi

LOG_STD_ACTION

LSD-2-TESTAPP2

2-Critical

Test app error: [chars]: [hec] [hec]

Test application error

mpls-mfi

LOG_STD_ACTION

LSD-2-INVALID_VAR2

2-Critical

[chars] 0x[hec] 0x[hec]

Function received invalid parameters

mpls-mfi

LOG_STD_ACTION

LSD-2-APP_NOTSUPP

2-Critical

[chars] interface does not support app [chars]

Interface does not support app

mpls-mfi

LOG_STD_ACTION

LSD-2-AVL

2-Critical

[chars] [hec]

AVL tree operation error

mpls-mfi

LOG_STD_ACTION

LSD-2-FPIHANDLER

2-Critical

[chars] [hec]

FPI Handler error

mpls-mfi

LOG_STD_ACTION

LSD-3-CHUNKMGR

3-Error

chunk mgr: [chars] 0x[hec]

Chunk manager error

mpls-mfi

LOG_STD_ACTION

LSD-3-REWMGR

3-Error

Rewrite Manager: [chars] 0x[hec]

Rewrite Manager error

mpls-mfi

LOG_STD_ACTION

LSD-3-REWMGR2

3-Error

[chars] 0x%08x 0x%08x

Rewrite lookup failed due to FPI inconsisency

mpls-mfi

LOG_STD_ACTION

LSD-3-EVTLOGBADSOURCE

3-Error

Illegal log event source: [dec]

Illegal event found in log buffer

mpls-mfi

LOG_STD_ACTION

LSD-3-UPDATELISTMGREXEC

3-Error

Illegal exec: [chars] [hec]

Illegal code execution

mpls-mfi

LOG_STD_ACTION

LSD-3-UPDATELISTMGR2

3-Error

[chars] [dec] [dec]

General error

mpls-mfi

LOG_STD_ACTION

LSD-3-APPMGR

3-Error

[chars] 0x[hec]

App Mansger error

mpls-mfi

LOG_STD_ACTION

LSD-3-CLIENT_CONN

3-Error

[chars]

Client connection error

mpls-mfi

LOG_STD_ACTION

LSD-3-CLIENT_CONN2

3-Error

[chars] [hec] [hec]

Client connection error

mpls-mfi

LOG_STD_ACTION

LSD-3-INTF_DB

3-Error

[chars]

interface db error

mpls-mfi

LOG_STD_ACTION

LSD-3-INTF_DB2

3-Error

[chars] [hec] [hec]

interface db error

mpls-mfi

LOG_STD_ACTION

LSD-3-LABEL

3-Error

[chars][dec]

label operation error

mpls-mfi

LOG_STD_ACTION

LSD-3-LABEL2

3-Error

[chars] [hec] [hec]

label error

mpls-mfi

LOG_STD_ACTION

LSD-4-LABEL_RESOURCE

4-Warning

label range [dec]-[dec] exhausted

MPLS application is trying to allocate more labels than configuration will allow

mpls-mfi

LOG_STD_ACTION

LSD-4-LABELFREETO

4-Warning

requested free timeout [dec] ms by [chars] limited to: [dec] ms

MPLS application label free timeout exceed max allowed

mpls-mfi

LOG_STD_ACTION

LSD-3-MULTISERVICEREQ

3-Error

Multiple outstanding service requests: [dec] [dec]

Server request attempted with one already outstanding

mpls-mfi

LOG_STD_ACTION

LSD-3-BADEXEC

3-Error

Unexpected Code Execution: [chars] [dec]

Unexpected Code Execution

mpls-mfi

LOG_STD_ACTION

LSD-3-INVALID_PROC_EVT

3-Error

Unexpected process event [dec] for pid [dec]

The LSD component received an unexpected process event notification for the process with the specified ID

mpls-mfi

LOG_STD_ACTION

LSD-3-OS_NOTIFY

3-Error

Process id [dec] [chars] error code [dec]

LSD was unable to notify the operating system about unregistration

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this condition " "has been previously reported and resolved in a later release. If not " "gather the output of <CmdBold>show version<NoCmd Bold> " "<CmdBold>show running-config<NoCmdBold> " "<CmdBold>show mpls infrastructure lsd apps<NoCmdBold> and contact " "your Cisco technical support representative."

LSD-4-HW_RESOURCE_EXHAUSTED

4-Warning

Hardware resource exhausted on [chars] of type [dec]

The platform has run out of hardware resources.

mpls-mfi

"Reduce the mpls configuration."

LSD-3-LABEL_TBL_ERR

3-Error

Failed to create new label table due to [chars]

Label space is not carved properly. This is likely due to platform capabilities.

mpls-mfi

"Check platform capabilities to make sure max label values are set correctly."

LSD_HA-2-RESOURCE

2-Critical

[chars]

System resource error occured

mpls-mfi

LOG_STD_REDUCE_ACTION

LSD_HA-4-CF

4-Warning

[chars][dec]

CF related error

mpls-mfi

LOG_STD_ACTION

LSD_HA-2-RF

2-Critical

[chars][dec]

RF related error

mpls-mfi

LOG_STD_ACTION

LSD_HA-3-INVALID_VAR

3-Error

[chars]

Function received invalid parameters

mpls-mfi

LOG_STD_ACTION

LSD_HA-3-GENERAL

3-Error

[chars]

Function received invalid parameters

mpls-mfi

LOG_STD_ACTION

LSD_HA-3-UNSENT_MSG_DB

3-Error

[chars]

Error happen in unsent msg db

mpls-mfi

LOG_STD_ACTION

LSD_HA-3-LABEL_RANGE_DB

3-Error

[chars]

Error happen in label range db

mpls-mfi

LOG_STD_ACTION

LFD-3-CHUNKMGRALLOC

3-Error

failed chunk alloc: [chars]

Chunk alloc failed

mpls-mfi

LOG_STD_ACTION

LFD-3-CHUNKMGRDEALLOC

3-Error

failed chunk dealloc: [chars]

Chunk free failed

mpls-mfi

LOG_STD_ACTION

LFD-3-UPDATEHANDLERFPI

3-Error

No handler installed: fpi=[dec] handler type=[chars]

No handler installed

mpls-mfi

LOG_STD_ACTION

LFD-3-UPDATEHANDLER2

3-Error

[chars] [hec] [hec]

Error in update handler

mpls-mfi

LOG_STD_ACTION

LFD-3-UPDATEHANDLER3

3-Error

[chars] [hec] [hec] [hec]

Error in update handler

mpls-mfi

LOG_STD_ACTION

LFD-4-NOFIBIDB

4-Warning

[chars] - ifnum [dec]

fibidb missing on linecard

mpls-mfi

LOG_STD_RECUR_ACTION

LFD-3-REWMGR

3-Error

Rewrite Manager: [chars] [hec]

Rewrite Manager error

mpls-mfi

LOG_STD_ACTION

LFD-3-REWMGR2

3-Error

[chars] 0x%08x 0x%08x

Rewrite lookup failed due to FPI inconsisency

mpls-mfi

LOG_STD_ACTION

LFD-3-FPIHANDLER

3-Error

LFD SSS Handler: [chars]

Error in fpi handler

mpls-mfi

LOG_STD_ACTION

LFD-2-FPIHANDLER3

2-Critical

[chars] [hec] [hec] [hec]

FPI Handler error

mpls-mfi

LOG_STD_ACTION

LFD-3-NULLFIBIDB

3-Error

NULL FIB IDB: [chars] [dec]

NULL FIB IDB encountered

mpls-mfi

LOG_STD_ACTION

LFD-3-NULLADJACENCY

3-Error

NULL Adjacency

NULL adjacency encountered

mpls-mfi

LOG_STD_ACTION

LFD-3-FPITYPEWRONG

3-Error

Require fpi type [chars] get fpi type [chars]

Unmatched FPI type

mpls-mfi

LOG_STD_ACTION

LFD-4-UNSUPPORTEDRW

4-Warning

Unexpected rewrites seen where MPLS is not supported by platform for this slot

MPLS is either not needed or not handled by the platform for this card and should not handle rewrites

mpls-mfi

LOG_STD_NO_ACTION

LFD-3-NORESOURCE

3-Error

[chars] [dec]

Resource Failure: [chars] [dec]

mpls-mfi

LOG_STD_ACTION

LFD-6-RESOURCE

6-Information

[chars]

MPLS software is disabled on LC

mpls-mfi

LOG_STD_NO_ACTION

LFD-3-LTABLEMEM

3-Error

Cannot allocate new mpls table [dec] of size [dec] needed for entry [dec]

Not enough contiguous memory for mpls forwarding table

mpls-mfi

LOG_STD_REDUCE_ACTION

LFD-3-SM

3-Error

[chars] [dec]

State Machine error: [chars] [dec]

mpls-mfi

LOG_STD_ACTION

LFD-3-SMBADEVENT

3-Error

Unexpected event [chars] for state [chars]

The LFD received an unexpected event for its state. The state of the LFD and the unexpected event are specified in the message text.

mpls-mfi

LOG_STD_ACTION

LFD-3-BADEXEC

3-Error

Unexpected Code Execution: [chars] [dec]

Unexpected Code Execution

mpls-mfi

LOG_STD_ACTION

LFD-3-EVTLOGBADSOURCE

3-Error

Illegal log event source: [dec]

Illegal event found in log buffer

mpls-mfi

LOG_STD_ACTION

LFD-2-AVL

2-Critical

[chars] [hec]

AVL tree operation error

mpls-mfi

LOG_STD_ACTION

LFD-3-CHUNKMGR

3-Error

chunk mgr: [chars] 0x[hec]

Chunk manager error

mpls-mfi

LOG_STD_ACTION

LFD-3-INTFDB

3-Error

intf db: [chars] [hec]

Interface db error

mpls-mfi

LOG_STD_ACTION

LFD-3-INTFDB2

3-Error

intf db: [chars] [hec] [hec]

Interface db error

mpls-mfi

LOG_STD_ACTION

LFD-3-BADFRRTYPE

3-Error

illegal frr type: [dec]

FRR request type error

mpls-mfi

LOG_STD_ACTION

LFD-4-OWNCHANGED

4-Warning

Owner changed for [chars] [dec]/[dec] from [dec] to [dec]

Label was previously installed by different installer

mpls-mfi

LOG_STD_ACTION

LFD-3-INVPLISTTYPE

3-Error

Wrong plist_type expected [dec] for [dec]/[dec] update was [dec]

Rewrite PLISTTYPE invalid for non-ip label table entry

mpls-mfi

LOG_STD_ACTION

LFD-3-INVRWID

3-Error

Wrong rwid [dec] for non-ip LTE [dec]/[dec]

Rewrite ID invalid for non-ip label table entry

mpls-mfi

LOG_STD_ACTION

LFD-3-INVLABELTYPE

3-Error

Wrong label type [dec] for non-ip LTE [dec]/[dec]

Label type invalid for non-ip label table entry

mpls-mfi

LOG_STD_ACTION

LFD-3-INVIPLABELTYPE

3-Error

Wrong label type [dec] for IP Label [dec] table [dec] prefix [chars] vrf [chars]

Label type is invalid for the indicated label table entry

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of" " <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and" "contact your Cisco technical support representative."

LFD-3-INVPLIST

3-Error

Wrong path list type [dec] for label [dec]/[dec] [chars]

The path list type is set incorrectly for the label in quest\n\ion

mpls-mfi

LOG_STD_ACTION

LFD-3-BADSHORTLABELADD

3-Error

Cannot add short label: path_idx [dec] moi_type [dec]

Unable to create MFI feature space in FIB entry so unable to store short path extension information there.

mpls-mfi

LOG_STD_ACTION

LFD-3-BADLABELADD

3-Error

Cannot add label - [chars].

Unable to create label due to reason given.

mpls-mfi

LOG_STD_ACTION

LFD-3-INVPATHLBL

3-Error

[chars] [chars]

An invalid outgoing label is attached to the prefix

mpls-mfi

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of" " <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and" "contact your Cisco technical support representative."

LFD-3-NOOCE

3-Error

Attempt to get labels from OCE failed - [chars].

Calling function has provided insufficient information to get labels.

mpls-mfi

LOG_STD_ACTION

LFD-3-XDRBADMAGIC

3-Error

xdr message for [chars] spilled out of allocated static storage

An internal software error occurred.

mpls-mfi

LOG_STD_ACTION

LFD-3-UNSUPPORTED_XDR

3-Error

[chars]

Decoding of an XDR message revealed data or format that is unsupported in the current release.

mpls-mfi

LOG_STD_ACTION

LFD-3-BROKERINITFAIL

3-Error

Failed to initialise lte RP broker facility

An internal software error occurred.

mpls-mfi

LOG_STD_ACTION

LFD-3-LCXDRCLIENT

3-Error

LTE distribution client: [chars]

An internal software error occurred.

mpls-mfi

LOG_STD_ACTION

LFD-3-NONIPINFO

3-Error

Non-ip info: [chars]

An internal software error occurred.

mpls-mfi

LOG_STD_ACTION

LFD-3-RPXDRCLIENT

3-Error

Invalid XDR Client: [chars]

An internal software error occurred.

mpls-mfi

LOG_STD_ACTION

LFD-3-ORPHANLTE

3-Error

Label [dec]/[dec] plist [dec] LDM: 0x[hec]

The LTE for the label was supposed to be deleted but is still present

mpls-mfi

"Collect the running configuration and output of " "<CmdBold>show mpls forwarding-table labels<NoCmdBold> " "<CmdArg>label-num<NoCmdArg> command and contact cisco " "technical service representative. "

LFD-3-RUNNING_TIMER

3-Error

[chars] [dec] [chars] [dec]

The MPLS forwarding entry for the specified label was deleted prior to the expiry of its associated timer

mpls-mfi

"If there is no matching bug for this problem " "please collect the output of <CmdBold>show mpls" " forwarding-table label <label> internal<NoCmdBold>" " and the error message traceback and file a bug" " report."

LFD-3-INVLABELUPDTYPE

3-Error

Wrong label type [dec] for label [dec] table [dec] [chars] [chars]

An invalid Label type was encountered during the specified operation

mpls-mfi

"If there is no matching bug for this problem " "please collect the output of <CmdBold>show mpls" " forwarding-table label <label> internal<NoCmdBold>" " and the error message traceback and file a bug" " report."

LFD-3-KEY_DB_INSERTFAIL

3-Error

[chars] entry 0x[hec] existing 0x[hec]

The element could not be inserted into the LFD's key database.

mpls-mfi

"If there is no matching bug for this problem " "please collect the output of " "<CmdBold>show mpls forwarding-table internal<NoCmdBold> and " "the error message traceback and file a bug"

LFD-3-FIB_SRC

3-Error

Label [[dec]/[dec]] [chars] [chars] [chars]

The fib entry could not be sourced for label in question.

mpls-mfi

"If there is no matching bug for this problem " "please collect the output of " "<CmdBold>show mpls forwarding-table internal<NoCmdBold> and " "<CmdBold>show ip route [vrf <name>] <prefix> <NoCmdBold> and " "the error message traceback and file a bug"

LFD-4-FIB_SRC1

4-Warning

Label [[dec]/[dec]] [chars] [chars] [chars]

The fib entry could not be sourced for label in question.

mpls-mfi

"If there is no matching bug for this problem " "please collect the output of " "<CmdBold>show mpls forwarding-table internal<NoCmdBold> and " "<CmdBold>show ip route [vrf <name>] <prefix> <NoCmdBold> and " "the error message traceback and file a bug"

LFD-3-OCE_CHAIN

3-Error

[chars]

NULL OCE in chain

mpls-mfi

LOG_STD_ACTION

LFD-3-UNSUPPORT_OCE

3-Error

Not support - [chars] [dec]

Unsupported OCE

mpls-mfi

LOG_STD_ACTION

LFD-3-CORRUPTED_PKT

3-Error

[chars]

lfd received corrupted packet

mpls-mfi

LOG_STD_ACTION

LFD-4-RE_ENTRANT

4-Warning

Re-entrancy detected: [chars]

lfd non ip recalculation has re-entrancy

mpls-mfi

LOG_STD_ACTION

LFD-3-LABEL_BLOCK_CHUNK

3-Error

[chars]

lfd label block chunk entry corrupted

mpls-mfi

LOG_STD_ACTION

LFD-3-INVPEXTLEN

3-Error

[chars] path ext : attempt to decode beyond XDR buffer cp 0x[hec] cp_end 0x[hec] msg_type [dec] msg_size [dec] padding [dec]

Accessing memory beyond XDR buffer length while decoding path extensions

mpls-mfi

LOG_STD_ACTION

LFD-3-FIBIPINVALID

3-Error

[chars] table: [dec] label: [dec]

IP path information is invalid for the indicated label table entry

mpls-mfi

LOG_STD_SH_TECH_ACTION

LFD-3-FIBIPINVALIDAF

3-Error

AF: [dec] [chars] table: [dec] label: [dec]

IP path information AF is invalid for the indicated label table entry

mpls-mfi

LOG_STD_SH_TECH_ACTION

LFD-3-FIBNONIPINVALID

3-Error

[chars] table: [dec] label: [dec]

Non IP path information is invalid for the indicated label table entry

mpls-mfi

LOG_STD_SH_TECH_ACTION

LFD-3-PATHEXTENCODE

3-Error

[chars] [chars] path list: %p path ext: %p

MPLS path extensions could not be encoded for distribution

mpls-mfi

LOG_STD_SH_TECH_ACTION

LSD-3-OUTLABEL_RESV_ERROR

3-Error

[chars] Platform-outlabels:[dec] prim:[dec] application-outlabels:[dec]

-

-

-

PSM-3-BADLABELADD

3-Error

Cannot add label - [chars].

Unable to create label due to reason given.

mpls-psm

LOG_STD_ACTION

PSM-3-NOOCE

3-Error

Attempt to get labels from OCE failed - [chars].

Calling function has provided insufficient information to get labels.

mpls-psm

LOG_STD_ACTION

PSM-3-NONIPINFO

3-Error

Non-ip info: [chars]

An internal software error occurred.

mpls-psm

LOG_STD_ACTION

PSM-3-CHUNK

3-Error

[chars]: [chars] [hec] [hec]

Parameterized Chunk Manager error occurred

mpls-psm

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "<CmdBold>show running-config<NoCmdBold> and <CmdBold>show process memory<NoCmdBold> " "and contact your Cisco technical support representative."

PSM-3-INVALIDPARAM

3-Error

Invalid parameter - [chars]

Calling function has passed an invalid parameter.

mpls-psm

LOG_STD_ACTION

PSM-3-NORESOURCE

3-Error

[chars] [dec]

Resource Failure: [chars] [dec]

mpls-psm

LOG_STD_ACTION

PSM-3-ISSU_REG

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

ISSU negotiation failed for this XDR client.

mpls-psm

"This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it."

PSM-3-L2_PATH

3-Error

[chars] - path set 0x[hec]%p path [chars]

Internal error while processing layer 2 path.

mpls-psm

LOG_STD_ACTION

TUN-3-API_ARGS

3-Error

unexpected arguments: [chars] [chars]

A public tunnel component api was driven with arguments outside the expected boundaries.

ip-tunnels

LOG_STD_ACTION

TUN-5-TUN_DB_IF

5-Notice

Operation on tunnel interface table failed for [chars] - [chars]

Manipulation of the tunnel interface table failed.

ip-tunnels

LOG_STD_ACTION

TUN-5-RECURDOWN

5-Notice

[chars] temporarily disabled due to recursive routing

-

TUNNEL_DDTS_COMPONENT

LOG_STD_NO_ACTION

TUN-5-RECURDOWN_SRC

5-Notice

[chars] linestate down recursive source interface next output [chars]

Whilst evaluating tunnel linestate we revisted a source interface.

ip-tunnels

LOG_STD_ACTION

TUN-3-ENDPOINT_STORE

3-Error

Operation [chars] failed for [chars]

Manipulation of the tunnel endpoint store failed.

ip-tunnels

LOG_STD_ACTION

TUN-3-MULTI_KEYS_INFO

3-Error

[chars] [chars]

Manipulation of the tunnel keys database failed.

ip-tunnels

LOG_STD_ACTION

TUN-3-MULTI_KEYS_INFO_ERROR

3-Error

[chars] [dec]

Manipulation of the tunnel keys database failed\n\ because of incorrect idb_index.

ip-tunnels

LOG_STD_ACTION

TUN-4-UDLR_IDB_ERROR

4-Warning

UDLR [chars] - [chars]

An error was encountered on a udlr interface

TUNNEL_DDTS_COMPONENT

LOG_STD_NO_ACTION

TUN-3-ENDPOINT_ERROR

3-Error

[chars] [chars]

An internal software error occurred when manipulating the tunnel\n\ endpoint database

TUNNEL_DDTS_COMPONENT

LOG_STD_NO_ACTION

TUN-5-IGNOREICMPMTU

5-Notice

[chars] ignoring received ICMP Type 3 Code 4 due to pmtud min-mtu setting

-

TUNNEL_DDTS_COMPONENT

"If you want the ICMP packet to be accepted and to be used to decrease\n\ the tunnel MTU then use the <CmdBold>tunnel path-mtu-discovery min-mtu\n\ <NoCmdBold> command to decrease the minimum mtu allowed. The min-mtu\n\ specified is the minimum tunnel payload mtu allowed.\n\ Use the <CmdBold>show interface tunnel<NoCmdBold> command to view the\n\ current path mtu discovery settings."

TUN-5-IGNOREICMP6MTU

5-Notice

[chars] ignoring received ICMP6 Type 2 Code 0 due to pmtud min-mtu setting

-

TUNNEL_DDTS_COMPONENT

"If you want the ICMP6 packet to be accepted and to be used to decrease\n\ the tunnel MTU then use the <CmdBold>tunnel path-mtu-discovery min-mtu\n\ <NoCmdBold> command to decrease the minimum mtu allowed. The min-mtu\n\ specified is the minimum tunnel payload mtu allowed.\n\ Use the <CmdBold>show interface tunnel<NoCmdBold> command to view the\n\ current path mtu discovery settings."

TUN-3-MTUCONFIGEXCEEDSL2MTU_IPV4

3-Error

[chars] IPv4 MTU configured [dec] exceeds tunnel maximum MTU [dec]

An IPv4 MTU value is configured on the tunnel interface and this value\n\ exceeds the tunnel's maximum MTU. This message is typically observed\n\ when the tunnel header size changes or when the MTU of the underlying\n\ exit interface changes. As a result of either the tunnel maximum MTU\n\ can change. This message can also be observed when using an IPv6\n\ tunnel to carry IPv4 since IPv4 MTU config in this case allows for a\n\ value to be configured that is greater than the tunnel's maximum MTU.\n\ As a result of any of these conditions packets may be dropped.

TUNNEL_DDTS_COMPONENT

"If a specific IPv4 MTU value is not required it is recommended that\n\ you leave the value at the default by typing <CmdBold>no ip mtu\n\ <NoCmdBold> on the tunnel interface. If a specific value is required\n\ it is recommended that you check the interface MTU value from the\n\ <CmdBold>show interface tunnel<NoCmdBold> command and adjust\n\ <CmdBold>ip mtu<NoCmdBold> on the tunnel interface to be lower than or\n\ equal to this."

TUN-3-MTUCONFIGEXCEEDSL2MTU_IPV6

3-Error

[chars] IPv6 MTU configured [dec] exceeds tunnel maximum MTU [dec]

An IPv6 MTU value is configured on the tunnel interface and this value\n\ exceeds the tunnel's maximum MTU. This message is typically observed\n\ when the tunnel header size changes or when the MTU of the underlying\n\ exit interface changes. As a result of either the tunnel maximum MTU\n\ can change. This message can also be observed when using an IPv6\n\ tunnel to carry IPv6 since IPv6 MTU config in this case allows for a\n\ value to be configured that is greater than the tunnel's maximum MTU.\n\ As a result of any of these conditions packets may be dropped.

TUNNEL_DDTS_COMPONENT

"If a specific IPv6 MTU value is not required it is recommended that\n\ you leave the value at the default by typing <CmdBold>no ipv6 mtu\n\ <NoCmdBold> on the tunnel interface. If a specific value is required\n\ it is recommended that you check the interface MTU value from the\n\ <CmdBold>show interface tunnel<NoCmdBold> command and adjust\n\ <CmdBold>ipv6 mtu<NoCmdBold> on the tunnel interface to be lower than\n\ or equal to this."

TUN-4-MTUCONFIGLESSTHAN_MINIPV4MTU

4-Warning

[chars] IPv4 MTU [dec] is lesser than the minimum IP MTU [dec] fragmentation may occur

The IPv4 MTU value calculated on the tunnel interface is less than\n\ the minimum IP MTU. The MTU of the underlying exit interface of the\n\ tunnel is too small. As a result fragmentation of the transport packet\n\ may occur before this goes out of the underlying exit interface.

TUNNEL_DDTS_COMPONENT

"If a specific MTU value is not required for the exit interface it is\n\ recommended that you leave the value at the default by typing\n\ <CmdBold>no mtu <NoCmdBold> on the exit interface. If a specific value\n\ is required it is recommended that you check the MTU value from\n\ the <CmdBold>show interface <NoCmdBold> command for the exit interface\n\ and adjust <CmdBold>mtu<NoCmdBold> on the tunnel exit to be higher than\n\ this."

TUN-4-MTUCONFIGEXCEEDSTRMTU_IPV4

4-Warning

[chars] IPv4 MTU configured [dec] exceeds tunnel transport MTU [dec]

-

TUNNEL_DDTS_COMPONENT

"If a specific IPv4 MTU value is not required it is recommended that\n\ you leave the value at the default by typing <CmdBold>no ip mtu\n\ <NoCmdBold> on the tunnel interface. If a specific value is required\n\ it is recommended that you check the tunnel transport MTU value from\n\ the <CmdBold>show interface tunnel<NoCmdBold> command and adjust\n\ <CmdBold>ip mtu<NoCmdBold> on the tunnel interface to be lower than or\n\ equal to this."

TUN-4-MTUCONFIGEXCEEDSTRMTU_IPV6

4-Warning

[chars] IPv6 MTU configured [dec] exceeds tunnel transport MTU [dec]

-

TUNNEL_DDTS_COMPONENT

"If a specific IPv6 MTU value is not required it is recommended that\n\ you leave the value at the default by typing <CmdBold>no ipv6 mtu\n\ <NoCmdBold> on the tunnel interface. If a specific value is required\n\ it is recommended that you check the tunnel transport MTU value from\n\ the <CmdBold>show interface tunnel<NoCmdBold> command and adjust\n\ <CmdBold>ipv6 mtu<NoCmdBold> on the tunnel interface to be lower than\n\ or equal to this."

TUN-4-MTUDEFAULTEXCEEDSL2MTU_IPV4

4-Warning

[chars] transport MTU [dec] exceeds [chars] configured IPv4 MTU [dec] fragmentation may occur

A default MTU value has been configured on the tunnel and this\n\ value exceeds the underlying physical interface MTU. As a result\n\ fragmentation of the transport packet may occur before this goes out\n\ of the underlying exit interface.

TUNNEL_DDTS_COMPONENT

"If possible increase the size of the IPv4 MTU on the underlying\n\ physical interface using <CmdBold>ip mtu<NoCmdBold>."

TUN-5-TUN_TABLE

5-Notice

Operation [chars] on tunnel table failed for [chars] - [chars]

Manipulation of the tunnel table failed.

ip-tunnels

LOG_STD_ACTION

TUN-3-DECAP_OCE

3-Error

[chars] [chars]

An internal software error occurred in the tunnel subsystem which is responsible for building forwarding for the purposes of decapsulation

-

LOG_STD_ACTION

TUN-3-DECAP_TINFO

3-Error

[chars] [chars]

An internal software error occurred in the tunnel subsystem which is responsible for driving forwarding based on the tinfo configuration

-

LOG_STD_ACTION

TUN-3-ILLEGAL_ARGS

3-Error

Illegal arguments - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

TUN-5-TUN_HWIDB_RECYCLE

5-Notice

Failed to recycle hwidb for Tunnel [dec] index [dec]

Recycling of tunnnel interface failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_SWIDB_RECYCLE

5-Notice

Failed to recycle swidb for Tunnel [dec] index [dec]

Recycling of tunnnel interface failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_HWIDB_DELETE

5-Notice

Failed to delete hwidb for Tunnel [dec] index [dec]

Deletion of tunnnel interface failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_SWIDB_DELETE

5-Notice

Failed to delete swidb for Tunnel [dec] index [dec]

Deletion of tunnnel interface failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_INTF_STATE_RESET

5-Notice

Failed to reset tunnel interface state for [chars]

Reset of tunnnel interface failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_UNIT_LIST_INSERT

5-Notice

Failed to add entry unit [dec] to tunnel unit list

Insertion of tunnnel unit failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_HWIDB_LIST_INSERT

5-Notice

Failed to add [chars] to tunnel hwidb list

Insertion of tunnnel to hwidb list failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_UNIT_LIST_DELETE

5-Notice

Failed to delete entry unit [dec] to tunnel unit list

Deletion from tunnnel unit failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_HWIDB_LIST_DELETE

5-Notice

Failed to delete [chars] from tunnel hwidb list

Deletion of tunnnel from hwidb list failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-TUN_LIST_CREATE

5-Notice

Failed to create tunnel list [chars]

Creation of tunnel list failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-HW_IF_INDEX_ILLEGAL

5-Notice

Attempt to create tunnel interface for [chars] with illegal index: [dec]

Creation of tunnel interface failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-INIT_ERROR

5-Notice

A critical error [chars]occurred during initialization

Creation of tunnel subsystem failed.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-TUN_SIDB2TUNS

3-Error

[chars]: [chars]

An internal software error occurred.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-TUN_SB

3-Error

TUN_SB: [chars][chars][chars]

An internal software error occurred.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-TUN_DBG

3-Error

TUN_DBG: [chars] [chars]

An internal software error occurred.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-TUN_HA

3-Error

Tunnel HA: [chars]

Tunnel HA encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-GROUPS

3-Error

Tunnel Groups: [chars]: [chars]

The tunnel group component encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-WCCP_GROUP

3-Error

Tunnel WCCP Groups: [chars]: [chars]

The tunnel group component encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-OTV_GROUP

3-Error

Tunnel OTV Groups: [chars]: [chars]

The tunnel group component encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-L3VPN_GROUP

3-Error

Tunnel L3VPN Groups: [chars]: [chars]

The tunnel group component encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-L3VPN_ENCAP_IP_PROFILE

3-Error

L3VPN Encap IP : [chars]: [chars]

The L3VPN Encap IP component encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-4-L3VPN_ENCAP_IP_SRC_DEL

4-Warning

L3VPN Encap IP : [chars]: [chars]

The user configuration change results in a warning. This message is typically printed when the user tries to delete a loopback interface and the loopback interface is configured as the source interface of the L3VPN encap IP profile

TUNNEL_DDTS_COMPONENT

"It is recommended that the user removes the loopback interface as the source interface of the L3vpn encap ip profile before deleting the loopback interface."

TUN-3-SIA_GROUP

3-Error

Tunnel SIA Groups: [chars]: [chars]

The tunnel group component encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-6RD

3-Error

[chars]: [chars]

The tunnel 6RD feature encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-6RD_INFO

5-Notice

[chars]: [chars]

6RD configuration has been removed as it is not compatible with the\n\ new sub-mode

TUNNEL_DDTS_COMPONENT

LOG_STD_NO_ACTION

TUN-3-CM1

3-Error

[chars]

The tunnel classification module encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-CM2

3-Error

[chars] [dec]

The tunnel classification module encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-3-TUNTO

3-Error

Operation: [chars] Action: [chars] Reason: [chars]

The tunnel-to module encountered an internal software error

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

TUN-5-L3VPN_IP_PROFILE_DELETE

5-Notice

l3vpn encap ip profile [chars] deleted

l3vpn encap ip profile is deleted

TUNNEL_DDTS_COMPONENT

LOG_STD_NO_ACTION

TUN-3-TERM_ADJ

3-Error

Terminal adjacency [chars][chars][chars]

An internal software error occurred.

TUNNEL_DDTS_COMPONENT

LOG_STD_ACTION

ADJ-3-BADMACALIGN

3-Error

adjacency mac string end [hec] not [chars] aligned

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-BADMAGIC

3-Error

adjacency [chars] is followed by bad magic

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ALLOCATEONDOWN

3-Error

Allocating adj when adj subsystem down

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ALLOCATEFAIL

3-Error

Failed to allocate an adjacency

An internal software error occurred. This is probably because not enough memory was available.

-

LOG_STD_ACTION

ADJ-3-BOARDENCAP

3-Error

Generation of encapsulation string for [chars] failed

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ILLEGALARGS

3-Error

Illegal arguments - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-STATETRANSITION

3-Error

Unexpected state transition from [chars] to [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-NOFIBIDB

3-Error

CEF Interface not found - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-LCXDRCLIENT

3-Error

Adjacency distribution client: [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-RPXDRCLIENT

3-Error

Adjacency distribution client: [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-BROKERINITFAIL

3-Error

Failed to initialise adjacency RP broker facility

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-SBINITFAIL

3-Error

Failed to initialise adjacency subblock facility

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ILINITFAIL

3-Error

Failed to initialise adjacency interest list facility

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-BUNDLES

3-Error

Adj bundles: [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ILALLOCATEFAIL

3-Error

Failed to allocate an adjacency interest list subblock

An internal software error occurred. This is probably because not enough memory was available.

-

LOG_STD_ACTION

ADJ-3-ILDEALLOCATEFAIL

3-Error

Failed to deallocate an adjacency interest list subblock

An internal software error occurred. This is probably because not enough memory was available.

-

LOG_STD_ACTION

ADJ-3-DBGFILTERALLOCATEFAIL

3-Error

Failed to allocate an adjacency debug filter block

An internal software error occurred. This is probably because not enough memory was available.

-

LOG_STD_ACTION

ADJ-3-ADJMGRALLOCATEFAIL

3-Error

Failed to allocate an adjacency summary event block

An internal software error occurred. This is probably because not enough memory was available.

-

LOG_STD_ACTION

ADJ-3-ADJGENALLOCATEFAIL

3-Error

Failed to allocate memory [chars]

An internal software error occurred. This is probably because not enough memory was available.

-

LOG_STD_ACTION

ADJ-3-ADJGENDEALLOCATEFAIL

3-Error

Failed to deallocate memory [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ADJMGRREFRESHFAIL

3-Error

Failed to dispatch a refresh adjacency summary event

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ADJMGRDISPATCHFAIL

3-Error

Failed to enqueue an adjacency summary event block

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-5-PARENT

5-Notice

Midchain parent maintenance for [chars] - [chars]

A midchain adjacency failed to stack onto output chain because a loop was detected. Traffic through the adjacency will be dropped until the adj is restacked. This condition is typically transient and is rectified by the control plane driving stacking. E.g. if an ip tunnel destination resolves through the tunnel transiently this message would appear. The situation would be rectified either by learning the tunnel destination through an interface other than the tunnel itself or by bringing the tunnel down. Monitor 'show adjacency internal' to determine if the problem has been resolved.

-

LOG_STD_NO_ACTION

ADJ-3-ADJSTACK2

3-Error

Adj stack2 error [chars]: [chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-5-ADJISSUINCOMPATIBLE

5-Notice

All or part of adjacency message for [chars] not sent to incompatible CEF instance for [chars]

The adjacency is not distributed in whole to the remote CEF instance. This may impact traffic forwarding on remote CEF instance

-

LOG_STD_NO_ACTION

ADJ-3-BADADDRTYPE

3-Error

Using an unsupported address type [dec] when trying to add/delete/modify/find an adjacency

An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made.

-

LOG_STD_ACTION

ADJ-3-BADADDRLEN

3-Error

Zero address length detected distributing adj [chars]

An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made.

-

LOG_STD_ACTION

ADJ-3-BADLINKTYPE

3-Error

Using an unsupported linktype [chars] when trying to add/delete/modify/find an adjacency

An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made.

-

LOG_STD_ACTION

ADJ-3-BADMACALIGN2

3-Error

Adjacency mac string for [chars] not byte aligned offset [hec] length [hec]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-MACOVERFLOW

3-Error

Adjacency mac address for [chars] overflowed by [dec] bytes

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-5-RESOLVE_REQ_FAIL

5-Notice

Adj resolve request failed for [chars] on [chars]

The source e.g. ARP or ND could not resolve the address.

-

LOG_STD_ACTION

ADJ-3-MACSTRING_PD_ERROR

3-Error

Platform request for header type [chars] from adjacency [chars] [chars][chars]

An internal software error occurred.

-

LOG_STD_ACTION

ADJ-3-ISSU_REG

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

ISSU negotiation failed for this XDR client.

-

"This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it."

ADJ-3-CONNID_POOL_EXHAUSTED

3-Error

Pool of connection ids is fully utilized. It may not be possible to encode new sets of extended keys.

Either there are too many unique sets of extended keys in the system or ids have been leaking.

-

LOG_STD_ACTION

ADJ-3-CONNID_INVALID_KEY

3-Error

Unexpected connection-id parameter: Expecting [chars] when encoding [chars]

An application has provided an invalid key for computing a connection-id.

-

LOG_STD_ACTION

ADJ-3-CONNID_TREE_OP_FAIL

3-Error

Tree [chars] failed for [chars] for id [dec] connid [dec]

A tree operation failed for the connection-id manager. An inability to correctly construct a tree will have negative consequences for the system.

-

LOG_STD_ACTION

ADJ-3-CONNID_INVALID

3-Error

Connection id [dec] not recognized [chars]

A supplied connection id did not exist in the managed id database.

-

LOG_STD_ACTION

ADJ-3-CONNID_INCOMPATIBLE_ID

3-Error

Connection id [dec] could not be transformed: [chars]

A connection id could not be transformed from a lower revision.

-

LOG_STD_ACTION

ADJ-3-CONNID_TREE_MISMATCH

3-Error

Supplied connid [dec] and extended keys [chars] do not match

An adjacency has a connection id and extended keys mapping that doesn't match what's in the managed connection id database. This will likely result in a rejected adjacency update or sync.

-

LOG_STD_ACTION

ADJ-3-ADJ_XKEYS

3-Error

Adj extended keys error [chars]: [chars]

An initialization error occurred for extended keys.

-

LOG_STD_ACTION

ADJ-3-XKEYS_XDR_LEN

3-Error

Expected [dec] bytes of extended adjacency keys: decoded [dec] bytes

The XDR message was incorrectly formatted and may contain bad xkey data.

-

LOG_STD_ACTION

BUNDLES-3-ALLOCATION

3-Error

Bundle allocation error: [chars]

An internal software error occurred. It is likely that this error is caused by a low memory condition

OCE_DDTS_COMPONENT

LOG_STD_ACTION

BUNDLES-3-PLATFORMSPACE

3-Error

Platform attempted to access unreserved space

An internal software error occurred.

OCE_DDTS_COMPONENT

LOG_STD_ACTION

BUNDLES-3-TYPENOTISSUAWARE

3-Error

Bundle type [chars] must be ISSU aware to send to slots [chars]

-

-

-

OCE-3-OCE_SET_WRONG_PATH

3-Error

Attempting to add an oce to the set contributed by path/list %p/%p while set set belongs to %p

Failed to enqueue a unlock for an oce this may lead to a memory leak

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-QUEUE_UNLOCK

3-Error

Failed to [chars] unlock[chars] for [chars] oce %p

Failed to enqueue a unlock for an oce this may lead to a memory leak

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-OCEDEPDUMP

3-Error

[chars]

An error condition triggered display of oce dependents

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-UNINITIALIZED_VECTOR

3-Error

Improperly initialized [chars] vector in [chars] OCE bundle %p packet dropped

An OCE bundle vector was improperly initialized

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-MISSING_HANDLER_FOR_SW_OBJ

3-Error

Missing handler for '[chars]' function

An internal API request has been ignored because it was unexpected

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-MISSING_HANDLER_FOR_SW_OBJ_TYPE

3-Error

Missing handler for '[chars]' function for type [chars]

An internal API request has been ignored because it was unexpected

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-OCE_CHANGED_BY_APPLY_FUNCTION

3-Error

Target OCE %p changed to %p by apply function %p

An internal disposition counter measure request has been ignored because it was unexpected

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-DECREASE_ZERO_REFCOUNT

3-Error

Try to decrease zero refcount for [chars] oce %p

Attempt to decrease the refcount of oce when it is already zero

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-INTERRUPT_LEVEL_LAST_LOCK

3-Error

Try to remove last lock for [chars] oce %p at interrupt

Attempt to delete oce while not at process level

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-GENERAL

3-Error

[chars]

An internal software error occurred.

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-LOOP

3-Error

A loop in the OCE chain has been detected at: [chars][%p]

A loop in the OCE chain has been detected

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE-3-EXCEED_OCE_COUNTER_LIMIT

3-Error

Exceeded OCE push counter limit functs:%p counter:%p

-

-

-

FRR_OCE-3-GENERAL

3-Error

[chars]

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-NULLPOINTER

3-Error

[chars]

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-INVALIDPAR

3-Error

Parent OCE %p[chars] is [chars]

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-INVALID_ADDRTYPE

3-Error

addrtype to xdr: [dec] [dec]

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-INVALID_BFD_HNDL

3-Error

[chars] bfd notification handle is %p

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-INVALID_BFD_EVT

3-Error

Error in BFD event retrieval bfd notification handle is %p session handle is %p

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-INVALID_BFD_SESSION

3-Error

BFD session db node mismatch: bfd context db node is %p frr db node is %p

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-3-ERROR_BFD_SESSION

3-Error

[chars]BFD returned [dec] node %p handle %p interface [dec]

An internal software error occurred.

OCE_DDTS_COMPONENT

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release."

FRR_OCE-4-INVALID_BACKUP_OCE

4-Warning

Invalid backup oce is found because interface %lu is removed or reloading

The interface or line card is reloading or removed.

OCE_DDTS_COMPONENT

"Check whether the line card is present and the interface is up."

FRR_OCE-4-NULL_PRIMARY_OCE

4-Warning

[chars]

The interface or line card is reloading or pulled off.

OCE_DDTS_COMPONENT

"Check whether the line card is in online and the interface is up."

FRR_OCE-5-ISSULOG

5-Notice

FRR is not ISSU compatible notified by [chars]

MPLS failed to set offset within packet

OCE_DDTS_COMPONENT

LOG_STD_ACTION

REPLICATE_OCE-6-PAK_TOO_SHORT

6-Information

Packet too short datagram size [dec] tl [dec]

An IP packet which is too short was received

OCE_DDTS_COMPONENT

LOG_STD_ACTION

REPLICATE_OCE-3-REPLICATE_PATH_WALK_FAIL

3-Error

[chars] [dec]

LSM Replicated packets may not be forwarded.

OCE_DDTS_COMPONENT

LOG_STD_ACTION

OCE_PUNT_PROCESS-3-NORESOURCE

3-Error

[chars] [dec]

Resource Failure: [chars] [dec]

mpls-mfi

LOG_STD_ACTION

OCE_PUNT_PROCESS-3-LABEL_CACHE_INVALID

3-Error

[chars]

MPLS label cache was invalid failed to handle exception

mpls-mfi

LOG_STD_ACTION

SIGNAL_OCE-3-SOCE

3-Error

Failed to [chars] signal oce [chars][chars]

An internal software error occurred.

OCE_DDTS_COMPONENT

LOG_STD_ACTION

SIGNAL_OCE-3-SOCE_SB_OPERATION_FAILED

3-Error

Failed to [chars] subblock on [chars]

An internal software error occurred.

OCE_DDTS_COMPONENT

LOG_STD_ACTION

FNF-6- AGER_OVERRIDE

6-Information

Flow [chars] time modified by [chars] to [dec]

The aging timer has been modified and may be different from configured value.

flexible-netflow

LOG_STD_NO_ACTION

FNF-6- ERROR

6-Information

FNF error: [chars]

An FNF error occurred.

flexible-netflow

"For more information repeat the action with FNF debugging enabled."

FNF-6- CONFIGURATION

6-Information

Invalid FNF configuration: [chars]

An invalid FNF configuration was detected.

flexible-netflow

"Review the FNF configuration before repeating the action."

FNF-3- LC_STATUS

3-Error

Flow monitor [chars] can not be added to [chars] rejected on module [chars] : [chars]

The flow monitor has been rejected on the specified module. It will have been removed from the RP configuration too. This can happen for example when a monitor is removed and added again immediately before the tidy has been completed or in the case where a flow monitor is waiting at automore when the monitor is removed from the interface then reapplied

flexible-netflow

"Check the configuration of the Flow Monitor that" " was applied for errors. If the rejection was" " due to the LC not having finished cleaning up after" " a previous removal of a Flow Monitor wait until" " the cleaning up has finished then reapply the" " config."

FNF-3- PROVISIONING

3-Error

[chars] failed to provision '[chars] flow monitor [chars] [chars]' on [chars]: [chars]

The attachment of the Flow Monitor to has had a problem on the device identified. It may be working on other devices and the configuration is retained.

flexible-netflow

"Check the device identified is working as expected" " and that it can support the configuration of the" " Flow Monitor to the chosen attachment point."

LISP-4-ASSERT

4-Warning

Internal LISP error [chars][chars]\n

LISP control plane code execution encountered an unexpected condition.

lisp

"show {ip | ipv6} lisp"

LISP-4-LOCAL_EID_RLOC_INCONSISTENCY

4-Warning

Inconsistent LISP routing locator configuration detected in the local EID database for instance-ID [dec] [chars] address family.

All the LISP local EID prefixes for an address family must be configured with the same set of routing locators. LISP detected that there are routing locators configured on some local EID prefixes and not on other local EID prefixes of the same address family.

-

"Issue the <CmdBold>show {ip | ipv6} lisp database" "<noCmdBold> command and look for routing " "locators marked as <CmdBold>missing<noCmdBold>. " "Configure the missing routing locators for the " "remaining local EID prefixes. If a routing locator" "must not be used for inbound traffic to a local " "EID prefix then a priority of 255 can be " "specified."

LISP-4-ROUTE_IMPORT_WARN

4-Warning

LISP [chars] RIB import warning[chars] [chars] reached [dec] routes limit set to [dec].

-

-

-

LISP-4-ROUTE_IMPORT_RIB_EVENT_DROPPED

4-Warning

LISP [chars] RIB [chars] route import events dropped after reaching queue size of [dec]. Re-evaluation scheduled in [dec] minutes.

The transient event queue used by LISP to store received RIB route import events reached the limit specified through the <CmdBold>{ipv4 | ipv6} route-import maximum-prefix <limit><noCmdBold> configuration. Subsequent RIB events were dropped. There may now be an inconsistency between the routes present in the RIB and those imported by LISP. A re-evaluation of LISP route import for the affected EID table has been scheduled to attempt to automatically recover from this condition.

-

"Modify the LISP <CmdBold>route-import<noCmdBold> " "configuration for the specified EID table to " "apply a route-map that only allows the desired RIB " "routes. If more routes are desired than the " "current limit you can increase it through the " "<CmdBold>maximum-prefix<noCmdBold> command. If " "error was a transient condition in the RIB you can " "force a re-evaluation of route import through the " "<CmdBold>clear {ip | ipv6} lisp route-import" "<noCmdBold>"

LISP-4-LOCAL_EID_NO_ROUTE

4-Warning

No route to local EID database prefix [chars].

There is no RIB route that covers or is a more specific of the configured local EID database prefix. This means that the ETR will not be able to forward decapsulated packets to their destination.

-

"Check the network connectivity and routing " "configuration within the LISP site and re-establish " "a route to destinations covered by the configured " "EID prefix."

LISP-4-SITE_XTR_RLOC_INCONSISTENCY

4-Warning

[chars] RLOC [chars] in EID database configuration in record for [chars] from [chars].

While probing other xTRs in our own site we received a map reply mapping record listing a different set of locators than those we have configured in database commands.

-

"Issue the <CmdBold>show {ip | ipv6} lisp database" "<noCmdBold> command on both this xTR and the other " "site xTR that sent us the map reply to locate the " "mis-configuration. Add or remove locators in the " "config of one or both xTRs to make them have the " "same list of configured locators."

LISP-5-MAP_SERVER_MAP_REQ_NO_ITR_ETR_REACHABILITY

5-Notice

Map request received for EID[chars] but map server does not

This message is to alert the user to the fact that a map request for an EID prefix is received by the map server and it doesn't have reacheablity to any ITR or ETR that registered this prefix so it cannot provide a useable locator to complete the EID-to-locator mapping.

-

"Normally this should not happen but if this " "condition persists it shows a connectivity problem " "between the map server and locators connected to the " "network."

LISP-4-CEF_DISABLED

4-Warning

Disabling [chars] CEF will impact configured LISP functionality.

CEF has been disabled whilst LISP has configuration which depends on CEF being enabled.

-

"Re-enable CEF using the command " "<CmdBold>{ip|ipv6} cef [distributed]<noCmdBold>."

LISP-4-UNSUPPORTED_LOCAL_RLOC

4-Warning

This platform does not support local [chars] RLOCs [chars] will be marked as down.

The platform has indicated it does not support local RLOCs of this address family.

-

"Deconfigure the RLOC or move it to another xTR at " "the site which does not have this platform " "limitation."

LISP-6-DDT_BAD_XTR_NONCE

6-Information

DDT resolver received two Map-Requests from [chars] for different EID prefixes but with the same nonce.

An xTR issuing LISP Map-Requests includes a nonce value in each request. The xTR must use a different nonce value for each Map-Request for a new EID prefix. The identified xTR has sent us two Map-Requests each for a different EID prefix and they both carried the same nonce value. When querying the DDT hierarchy duplicate nonce values prevent the DDT resolver from associating received Map-Referral messages with the correct request. To protect against this problem the DDT resolver has dropped the second of the two received requests.

-

"Contact the operator of the ITR that is issuing " "the Map-Requests so that they can fix the problem " "by upgrading their system."

LISP-4-MAP_CACHE_WARNING_THRESHOLD_REACHED

4-Warning

The LISP map-cache limit warning threshold [dec]/[dec] entries for instance-id [dec] has been reached.

-

-

-

LISP-4-MAP_CACHE_CREATE_FAILURE

4-Warning

Failed to create map cache entry for EID prefix [chars] under Lisp instance-id [dec] Cause: [chars]

This message is a notification that the map cache creation for an EID prefix has failed. Probable reasons could be failure to create or lookup a corresponding map cache entry due to inconsistent states low memory conditions or commonly if map-cache-limit is explicitly set to a low value. If the cache size limit is reached new entries will replace old/inactive ones as required. If the map-cache limit is set too low actively used EID-to-RLOC mappings may be replaced continously which causes traffic to be dropped while these mappings are re-

-

"If this limit is reached and traffic drops are " "experienced consider re-evaluating the map-cache " "limit and configure a higher limit."

LISP-4-DATABASE_MAPPING_LIMIT_DYNAMIC_REACHED

4-Warning

The LISP dynamic database-mapping limit[chars] [dec]/[dec] dynamic entries for eid-table [chars] has been reached.

-

-

-

LISP-4-DATABASE_MAPPING_PLATFORM_LIMIT_REACHED

4-Warning

The LISP database-mapping platform limit of [dec] has been reached. Current count is [dec].

This message is a warning that the local database size has hit the platform limit. The limit may be reached during normal operation if a xTR discovers a large number of dynamic hosts in the EID-prefix ranges enabled for dynamic learning. If the dynamic local database size limit is reached new hosts will not be discovered. It is worth noting that it is normal for the local database to have a limit for dynamic entries for example to set an upper limit on the amount of memory required. To diagnose this issue it may be helpful to inspect the local database using show ip[v6] lisp [eid-table <vrf>] database. The entries can also be cleared with clear lisp[eid-table <vrf>] dynamic-eid.

-

"If this warning persists and traffic drops are " "experienced please contact TAC."

LISP-4-DYNAMIC_RSRC_PLATFORM_WARNING_LIMIT_REACHED

4-Warning

The LISP [chars] EID warning limit greater than [dec] percent for platform

This message is a warning that the EID resource size has hit the platform warning limit. The limit may be reached during normal operation if a xTR has a large number of Local hosts/and or Remote map-caches entries. To diagnose this issue it may be helpful to inspect the platform resource usage using show lisp platform

-

"If this warning persists traffic drops can be " "experienced please contact TAC."

LISP-4-DYNAMIC_RSRC_PLATFORM_LIMIT_REACHED

4-Warning

The LISP [chars] EID platform limit [dec] percent has been reached.

This message is a warning that the EID resource size has hit the platform limit. The limit may be reached during normal operation if a xTR has a large number of Local hosts/and or Remote map-caches entries. To diagnose this issue it may be helpful to inspect the platform resource usage using show lisp platform

-

"If this warning persists traffic drops can be " "experienced please contact TAC."

LISP-4-CONFIGURED_MAX_LOCAL_HOSTS_LIMIT_REACHED

4-Warning

The LISP [chars] configured Local EID limit [dec] has been reached.

-

-

-

LISP-4-REMOTE_EID_EVICTION_TRIGGERED

4-Warning

The LISP [chars] EID platform limit reached. Remote EID eviction triggered to make space for Local EIDs. The eviction will continue till the Local EID Reserved [dec] percentage is reached.

-

-

-

LISP-4-SITE_REGISTRATION_LIMIT_EXCEEDED_ON_CONFIG

4-Warning

Configured site-registration limit [dec] is less than or equal

The newly configured limit is less than the current count of registrations.

-

"Issue <CmdBold>clear lisp <id> site<noCmdBold> for " "limit to take immediate effect."

LISP-4-SITE_REGISTRATION_LIMIT_EXCEEDED

4-Warning

Configured site-registration limit [dec] has been reached or

Map-server cannot create any more site registrations which are not explicitly configured. Consequently at least one map-register has been dropped.

-

"Increase the site registration limit using " "<CmdBold>site-registration limit <limit><noCmdBold> " "or limit the number of registrations from ETRs."

LISP-4-SITE_REGISTRATION_LIMIT_WARNING

4-Warning

Configured site-registration warning threshold [dec]/[dec] > [dec]%%

Site registration count has reached or exceeded the configured threshold. This is used to warn the adminstrator that corrective action may need to be taken to avoid reaching the configured site registration limit.

-

"No immediate action is required. Administrator may " "want to consider whether ETR registrations should " "be limited or capacity provisioned to accomodate " "growth in registration count."

LISP-4-LOCAL_EID_MAP_REGISTER_FAILURE

4-Warning

[dec] IID [dec] Failed to receive map-notify from map-server [chars]

This implies the map-sever may not have received/processed the map-register from this ETR or the map-server failed to successfully deliver the map-notify to the ETR.

-

"Ensure map-server is configured to accept " "map-register for this EID prefix ETR is " "configured with the correct map-server key and " "bidirectional traffic can flow between ETR and " "map-server."

LISP-5-MAP_RESOLVER_REACHABILITY_CHANGE

5-Notice

[dec] IID [dec] Map-resolver [chars] is [chars].

No route to reach map-resolver hence map-cache will not get resolved.

-

"Ensure ITR has connectivity to map-resolver."

LISP-5-MAP_SERVER_REACHABILITY_CHANGE

5-Notice

[dec] IID [dec] Map-server [chars][chars] is [chars].

No route to reach map-server so local EID database prefix will not get registered.

-

"Ensure ETR has connectivity to map-server."

LISP-5-PROXY_ETR_REACHABILITY_CHANGE

5-Notice

[dec] IID [dec] Proxy ETR [chars] is [chars].

No route to reach proxy ETR so traffic drop is expected.

-

"Ensure router has connectivity to proxy ETR."

LISP-6-MAP_SERVER_SITE_ALL_REGISTRATION_EXPIRED

6-Information

[dec] IID [dec] Map-Server site [chars] all registrations expired

-

-

-

LISP-5-MAP_SERVER_REGISTER_NO_CONFIG_EID_PREFIX

5-Notice

[dec] IID [dec] No site configuration to accept

No site is configured to accept registration for EID prefix.

-

"Configure EID prefix in map-server site to " "enable registration."

LISP-5-MAP_SERVER_REGISTER_AUTHENTICATION_FAILURE

5-Notice

[dec] IID [dec] Site [chars] Failed to authenticate map-register for

Map-server failed to authenticate map-register for EID prefix. This is potentially caused by different shared keys configured on ETR and map-server.

-

"Ensure ETR and map-server have the same " "configured shared key."

LISP-5-MAP_SERVER_REGISTER_ALLOWED_LOCATOR_MISMATCH

5-Notice

[dec] IID [dec] Site [chars] Allowed locator mismatch in map-register

The map-register contains RLOC that is not in the site's allowed locator list.

-

"Ensure map-server has the registering RLOCs " "added to the site's allowed locator list."

LISP-4-MAP_SERVER_SITE_EID_PREFIX_LIMIT

4-Warning

[dec] IID [dec] Site [chars] Map-server site dynamic EID prefix

Map-server cannot create any more dynamic EID prefix entry result accept-more-specifics. Consequently the map-register is not processed.

-

"Increase the map-server dynamic EID prefix " "entry limit."

LISP-4-MAP_SERVER_SITE_EID_PREFIX_LIMIT_THRESHOLD

4-Warning

[dec] IID [dec] Site [chars] Map-server site dynamic EID prefix

Dynamic EID prefix entry count has reached or exceeded the configured threshold. This is used to warn the adminstrator that corrective action may need to be taken to avoid reaching the map-server EID prefix limit.

-

"No immediate action is required unless the " "entry count is very close to the configured " "limit at which point the limit on the map-server " "needs to be adjusted."

LISP-4-MAP_SERVER_SITE_EID_PREFIX_LIMIT_CONFIG

4-Warning

Configured limit [dec] is less than current EID prefix count

The newly configured limit is less than the current EID prefix count.

-

"Issue \"clear lisp site\" for limit to " "take effect."

LISP-4-MAP_SERVER_SITE_EID_PREFIX_PLATFORM_LIMIT

4-Warning

Map-server site EID prefix entry platform limit for [chars] is reached [dec]: prefix [chars] in [dec] IID [dec] Site [chars] blocked

-

-

-

LISP-4-MAP_SERVER_EXTRANET_EID_PREFIX_PLATFORM_LIMIT

4-Warning

Map-server Extranet policy EID platform limit for [chars] is reached [dec]: prefix [chars] in [dec] IID [dec] Extranet [chars] blocked

-

-

-

LISP-5-MAP_RESOLVER_MAP_REQUEST_FILTERED

5-Notice

[dec] IID [dec] Map-resolver filtered map-request from [chars].

-

-

-

LISP-4-LISP_TOP_RLOC_AUDIT

4-Warning

[dec] router lisp instances [router lisp [chars]] are not

This message is a warning that the one or more configured router lisp <x> instances are missing the locator-table config. Without this locator-table the lisp instance is not operational.

-

"The operator must configure the " "locator-table below the router lisp instances or "

LISP-5-LISP_TCP_SESSION_STATE_CHANGE

5-Notice

Lisp session to peer address [chars] changed to [chars].

This message is a notification that the specified session has gone up/down. Please note that the messages is rate limited to 1 message a second and a session state could have changed without creating a message.

-

"If the session is expected to go up/down then" "no action is required. Otherwise investigation" "regarding the session going up/down should be" "done."

LISP-4-INTERRUPT

4-Warning

Internal LISP error during interrupt [chars]

-

-

-

LISP-3-TCP_MSG_TOO_LARGE

3-Error

Received too large TCP message type [dec] lenth [dec] > [dec] resetting the session

This message is a warning that a too large TCP message is received. LISP resets the session

-

-

LISP-3-TCP_AO_KEYCHAIN_CHANGED

3-Error

TCP Authentication Option keychain [chars] no longer valid

This message is a warning that the TCP keychain configuration was changed while it was in use.

-

"The TCP keychain configuration was changed while " "being used by LISP session. Correct the " "configuration to restore session"

LISP-3-MAP_CACHE_EXTRANET_SITE_REG_ERR

3-Error

Config map-cache site-registration should not be configured on lisp extranet instance [dec]

Config map-cache site-registration is not supported on lisp instances part of extranet

-

"Remove config map-cache site-registration from " "lisp instances part of extranet. Consider using " "config map-cache extranet-registration under " "provider instance"

LISP-4-MAP_REGISTER_WARNING

4-Warning

Map-Server received registration for a /0 subnet which specifies an attempt to register all prefix range

This message is a warning that the Map-Server received a registration message for a /0 subnet. An XTR may be attempting to receive all traffic of the network

-

"Check the router lisp configuration on XTR. " "Consider removing/changing the /0 eid-prefix in " "database mapping entry on XTR"

LISP-4-EXTRANET_OVERLAPPING_PREFIX

4-Warning

[dec] Map-Server detected overlapping prefix [chars] in extranet [chars]

An extranet prefix configured or dynamically learnt on one extranet IID cannot overlap with a prefix in another extranet.

-

"If it is not for specific purposes like firewall " "or service insertion please remove configuration " "causing overlapping extranet prefix to be learnt " "with different instance ID or in a different " "extranet."

LISP-4-MAP_REQUEST_NO_USABLE_ITR_RLOC

4-Warning

IID [dec] No usable ITR RLOC unable to send map-request.

This message is a warning that the device does not have any usable ITR RLOC for map-request transmission. When this condition occurs new traffic is impacted.

-

"Verify there is any least one static local EID " "configured or a dynamic EID is detected or " "\"map-request itr-rlocs\" is configured or the " "device is configured as a proxy-itr. If the " "message persists then verify the RLOC is local " "and in UP state."

LISP-4-MAP_SERVER_CONVERGING

4-Warning

IID [dec] Map-server is converging unable to send negative map-reply.

This message is a warning that the map-server is converging after reload or HA event. During this time the map-server would not send negative map-reply hence traffic would be impacted. It typically takes 3-6 minutes for the map-server to converge.

-

"Ensure there is at least two map-servers " "in the network for redundancy. When reload is " "required then ensure the peering map-server is " "fully converged before triggering reload."

LISP-4-PETR_EXTRANET_LOCATOR

4-Warning

[dec] Map-Resolver detected the PETR locator [chars] with

Map resolver does not allow PETR locator's instance outside of the instances configured as extranet Policy

-

"Remove configuration causing locator-set with " "extranet prefix to be advertised to instances " "outside of extranet."

LISP-5-SSO_SWITCHOVER_TIMEOUT

5-Notice

LISP SSO switchover timeout expired

LISP is running in the Hot Standby mode and after switchover RIB did not converge in 3 minutes

-

"BGP has many routes to process with " "as RIB has many routes ensure all of them " "were processed."

LISP-4-CONFIG_INVALID_PREFIX_SOURCE_WITH_DEFAULT_ETR

4-Warning

This message is a warning that the eid-prefix [chars] being used by default-etr is imported into LISP by another configuration.

PxTR doesn't allow the eid-prefix that is being used by default-etr to be imported into LISP by another source.

-

"Remove configuration causing conflict for the eid-" "prefix source from the PxTR/xTR"

DEFAULT-3-ERR_MSG

3-Error

[chars]

-

-

-

MSMR-3-MSMR_MSG

3-Error

[chars]

-

-

-

MSMR-7-MSMR_MSG

7-Debug

[chars]

-

-

-

TCP-3-TCP_MSG

3-Error

[chars]

-

-

-

TCP-7-TCP_MSG

7-Debug

[chars]

-

-

-

CONFIGURATION-3-CONFIG_MSG

3-Error

[chars]

-

-

-

CONFIGURATION-7-CONFIG_MSG

7-Debug

[chars]

-

-

-

MESSAGES-3-MESSAGES_MSG

3-Error

[chars]

-

-

-

MESSAGES-7-MESSAGES_MSG

7-Debug

[chars]

-

-

-

EVENTS-3-EVENT_MSG

3-Error

[chars]

-

-

-

EVENTS-7-EVENT_MSG

7-Debug

[chars]

-

-

-

WORK_QUEUE-3-WORK_QUEUE_MSG

3-Error

[chars]

-

-

-

EVENTS-7-EVENT_MSG

7-Debug

[chars]

-

-

-

TASK_SCHEDULER-3-TASK_SCHEDULER_MSG

3-Error

[chars]

-

-

-

-

3-Error

[chars]

-

-

-

DEFAULT-3-DEFAULT_MSG

3-Error

[chars]

-

-

-

DEFAULT-7-DEFAULT_MSG

7-Debug

[chars]

-

-

-

MSMR-3-ASSERT

3-Error

Internal LISP error

-

-

-

MSMR-3-LOCAL_EID_RLOC_INCONSISTENCY

3-Error

Inconsistent LISP routing locator configuration detected in the local EID database

-

-

-

MSMR-4-ROUTE_IMPORT_WARN

4-Warning

LISP RIB import warning reaching routes limit

-

-

-

MSMR-3-LOCAL_EID_NO_ROUTE

3-Error

No route to local EID database prefix.

-

-

-

MSMR-3-SITE_XTR_RLOC_INCONSISTENCY

3-Error

RLOC in EID database configuration inconsistency from this source RLOC.

-

-

-

MSMR-3-UNSUPPORTED_LOCAL_RLOC

3-Error

This platform does not support local RLOCS for this address family RLOC will be marked as down

-

-

-

MSMR-3-DDT_BAD_XTR_NONCE

3-Error

DDT resolver received two Map-Requests for different EID prefixes but with the same nonce.

-

-

-

MSMR-3-MAP_CACHE_WARNING_THRESHOLD_REACHED

3-Error

The LISP map-cache limit warning threshold has been reached.

-

-

-

TCP-6-LISP_TCP_SESSION_STATE_CHANGE

6-Information

Lisp session state to peer changed.

-

-

-

MSMR-3-MAP_SERVER_REGISTER_NO_CONFIG_EID_PREFIX

3-Error

No site configuration to accept registration for EID prefix.

-

-

-

MSMR-3-MAP_SERVER_REGISTER_AUTHENTICATION_FAILURE

3-Error

Failed to authenticate map-register for EID prefix.

-

-

-

MSMR-3-MAP_SERVER_SITE_ALL_REGISTRATION_EXPIRED

3-Error

all registrations expired

-

-

-

MSMR-3-MAP_SERVER_OVERLAP_PREFIX

3-Error

Map-Server detected overlapping prefix. Eid-prefix already registered by another RLOC

-

-

-

MSMR-5-MAP_SERVER_MAP_REQ_NO_ITR_ETR_REACHABILITY

5-Notice

Map request received for EID but map server does not have reachablity to any RLOCs.

-

-

-

MSMR_INFRA-3-MEM_ALLOC_FAILED

3-Error

Memory allocation failed

-

-

-

TCP-6-LISP_TCP_FLOW_CONTROL

6-Information

TCP session has flow-control state change

-

-

-

TCP-6-LISP_TCP_REJECT

6-Information

Incoming TCP connection rejected

-

-

-

MESSAGES-3-KAFKA_SEND_FAIL

3-Error

Failed to send message via Kafka

-

-

-

CONFIGURATION-6-CONFD_CONNECTED

6-Information

Connected to ConfD.

-

-

-

CONFIGURATION-3-CONFD_DISCONNECTED

3-Error

Cannot connect to ConfD. Configuration changes will be processed when the connection is established.

-

-

-

CONFIGURATION-6-CONFIG_READ

6-Information

Configuration read.

-

-

-

CONFIGURATION-3-CONFIG_REJECTION

3-Error

The config was NOT accepted

-

-

-

MSMR_INFRA-7-PLATFORM_CONFIG

7-Debug

Platform config

-

-

-

CONFIGURATION-3-CONFIG_MULTIPLE_LISP_ROUTER_INSTANCE

3-Error

multiple lisp router instances are configured on startup Linux MSMR only supports single lisp router instance

-

-

-

CONFIGURATION-3-CONFIG_MULTIPLE_TENANT

3-Error

multiple tenant config request Linux MSMR only supports single tenancy

-

-

-

CONFIGURATION-3-CONFIG_EIDID_PREFIX_VNI_MISMATCH

3-Error

prefix/vni does not match the eid id

-

-

-

CONFIGURATION-3-CONFIG_INVALID_ADDRESS_TYPE

3-Error

eid id address type is invalid

-

-

-

CONFIGURATION-3-CONFIG_INVALID_EIDID

3-Error

eid id is invalid. Expected eid id format is [virtual network id]prefix/mask length

-

-

-

CONFIGURATION-4-CONFIG_DELETED_AFTER_CONFD_RECONNECTED

4-Warning

config deletion is detected after lisp is reconnected to confd

-

-

-

CONFIGURATION-4-CONFIG_CHANGED_DURING_CONFD_DISCONNECTION

4-Warning

config change is detected after lisp is reconnected to confd

-

-

-

CONFIGURATION-3-CONFIG_INVALID_SITE_NAME_SIZE

3-Error

invalid site name size is configured

-

-

-

CONFIGURATION-3-CONFIG_INVALID_SITE_KEY_SIZE

3-Error

invalid key size is configured

-

-

-

CONFIGURATION-3-CONFIG_INVALID_TENANT_NAME_SIZE

3-Error

invalid tenant name size is configured

-

-

-

TCP-3-TCP_MSG_TOO_LARGE

3-Error

Received too large TCP message resetting the session

-

-

-

MSMR-3-NOTIFICATION

3-Error

Notification issued

-

-

-

XOS-7-XOS_ONINT

7-Debug

XOS APIs cannot be called in a interrupt path

An XOS API was called in the interrupt path this is currently not supported.

infra-xoslib

"Please check your code and avoid using this API in the interrupt path"

XOS-7-XOS_DM_WAIT

7-Debug

xos_dm_wait API cannot be called by a process that does not own the XDM xdm pid: [dec] current pid: [dec]

The xos_dm_wait API was called by a process that is not the owner of that \n XDM. Only process that create the XDM instance can own it.

infra-xoslib

"Please check your code and avoid invoking this API in a different process \n" "context."

XOS-7-XOS_DM_DISPATCH

7-Debug

xos_dm_dispatch API cannot be called that does not own the XDM xdm pid: [dec] current pid: [dec]

The xos_dm_dispatch API was called by a process that is not the owner of \n that XDM. Only process that create the XDM instance can own it.

infra-xoslib

"Please check your code and avoid invoking this API in a different process \n" "context."

XOS-7-XOS_DM_XDISPATCH

7-Debug

xos_dm_xdispatch API cannot be called that does not own the XDM xdm pid: [dec] current pid: [dec]

The xos_dm_xdispatch API was called by a process that is not the owner of \n that XDM. Only process that create the XDM instance can own it.

infra-xoslib

"Please check your code and avoid invoking this API in a different process \n" "context."

XOS-7-XOS_STUCK_TMR

7-Debug

XOS timer expired earlier than expected expiration time tree:%p time:[dec].[dec]

The XOS timer handler was invoked earlier than expiration value of the \n timer

infra-xoslib

"Please check expiration timer value set on the timer. Also some OS \n" "infrastructures can roundup expiration time so that timer handler gets \n" "invoked earlier than expected "

PARSER-4-MULTIPLEIFS

4-Warning

interface_action: multiple ifs present when unit_only set

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-LINKPOINT

4-Warning

Parser reached link_point

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-3-CREATEINT

3-Error

Can't create any more subinterfaces

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-NUMHELP

4-Warning

general_number_short_help: Invalid [chars] number flag

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-NVGEN

4-Warning

nvgen_token called but csb->nvgen not set

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-PROTOADDR

4-Warning

protoaddr_action: Unknown link_type [dec]

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-MULFUNCS

4-Warning

unknown test in test_multiple_funcs '[chars]'

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-3-NOLINK

3-Error

no link_point[dec] in the [chars] [chars] command chain

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-INVLDLINE

4-Warning

Invalid line in NV generation: [t-line]\n

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-2-INTDISABLE

2-Critical

Interrupts disabled in mode [chars] by command '[chars]'

A hardware or software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-BADRANGE

4-Warning

Bad range <[dec]-[dec]> for command '[chars]'

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-BADRANGELONGLONG

4-Warning

Bad range <%ld-%ld> for command '[chars]'

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PARSER-4-BADCFG

4-Warning

Unexpected end of configuration file.\n

This message occurs when a configuration is read from the Trivial File Transfer Protocol TFTP server or nonvolatile RAM NVRAM and the end

-

"Make sure the configuration is good then execute either a copy " "running-config startup-config command to write the good configuration " "to NVRAM or a copy running-config tftp command to write to a network " "TFTP server."

PARSER-4-INVLDNVGEN

4-Warning

Invalid function called in NVGEN of '[chars]'

An error occurred.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical " "support representative."

PARSER-4-INVLDSYNTX

4-Warning

Syntax cleanup list updated while not syntax checking. \nFuncPtr / Context [chars]

Functions were mistakenly called there may be more than listed

-

"show version"

PARSER-5-CFGLOG_LOGGEDCMD

5-Notice

User:[chars] logged command:[chars]

The config logger which logs every CLI command has an option to log messages to syslog - whenever a CLI command is executed this message is printed.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the parser and config logger. If you do not wish " "to see this syslog message type \"no cfglog send to syslog\"."

PARSER-3-CFGLOG_NOMEM

3-Error

User:[chars] [chars]

The command that was entered could not be logged because of a lack of memory. It is possible that the system logger syslog can allocate

-

"Attempt to free up memory on the router by stopping nonessential " "processes or unused features that may be running. Once sufficient " "memory is available this message will no longer appear."

PARSER-3-CFGLOG_EMPTYCMD

3-Error

User:[chars]

The user specified entered an empty command for which a log attempt was made. Normally empty commands will not be logged.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Execute a \"show cfglog " "user <username listed above> xml detailed\". Contact your technical " "support representative."

PARSER-3-CFGLOG_NOUSER

3-Error

Command:[chars]

Could not determine the user when logging the above command. Hence it could not be saved in the config log.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Determine if possible "

PARSER-3-CFGLOG_INCONSISTENT

3-Error

User:[chars] command:[chars]

When logging a command entered on the CLI the Config Logger detected an inconsistency in the log. This inconsistency may result in a failure to log the command.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Determine if possible "

PARSER-3-CFGLOG_PURGEFAILED

3-Error

Purge config log failed.

Failed to purge some of the config log entries

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical support " "representative with this information."

PARSER-3-CFGLOG_INITFAILED

3-Error

Initialization of the Config Log subsystem failed.

During initialization one or more queues/data structures essential to the config logger could not be set up. As a result the config logger will not be available for use.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical support " "representative with this information."

PARSER-3-CFGLOG_CLI_INITFAILED

3-Error

Initialization of the Config Log CLI failed.

Config Log CLI commands may not be accessible and hence the Config Logger may not be accessible via the IOS CLI.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical support " "representative with this information."

PARSER-3-CFGLOG_SESSIONERR

3-Error

Could not delete config log session:[dec] for user:[chars].

When a user logged out the Config Logger was unable to clean up information about the user's login session. The result might be a memory leak or inability to add new commands to the Config Log.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical support " "representative with this information."

PARSER-3-CFGLOG_RESIZE_FAILED

3-Error

Could not resize the config logger to new size:[dec]

Due to an internal error a request to resize the config log was not carried out. Apart from a failure to resize there should be no change in the behavior of the config logger.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical support " "representative with this information."

PARSER-3-BADLINK

3-Error

bad link point %p

Software attempted to perform an invalid parser operation.

-

"Copy the error message exactly as it appears. Execute a show version " "command and copy the displayed information. Contact your technical " "support representative."

PARSER-3-URLOPENFAIL

3-Error

cannot open file for redirection '[chars]'

The destination URL for the redirection cannot be opened for writing.

-

"Check for proper Uniform Resource Locator syntax and for write " "permission. Also check for free space and retry"

PARSER-3-CFGLOG_PERSIST_FILESYS_FULL

3-Error

Configuration logger persistency: Add command to persistent db failed. File system '[chars]' full.

When logging a command entered on the CLI into the configuration logger persistent database the Config Logger persistency detected zero bytes free in the file system.

-

"Check the space available in the filesystem displayed reported. " "Use 'dir <filesystemname>:' to find out the bytes free. " "Clear out some space for the configuration logger persistency " "feature to continue store the config commands logged in to the " "persistent database."

PARSER-3-CFGLOG_PERSIST_DB_OPEN_FAILED

3-Error

Configuration logger persistency: opening persist db failed. File '[chars]'.

The file open for writing/reading persisted commands failed.

-

"Check for the file system availablity. The file system " " might have got corrupted. Try formatting the file system."

PARSER-3-CFGLOG_PERSIST_APPLY_CMD_FAILED

3-Error

Configuration logger persistency: Applying config command '[chars]' failed. result '[dec]'.

When applying the command to the running configuration the parser returned an error.

-

" Parser encountered an error when the command is applied " " to the running configuration during reload. Verify no" " other process locks the configuration mode during this " " time. The parser could be locked by the HA or SNMP or by " " some other process."

PARSER-5-CFGLOG_PERSIST_APPLY_ON_RELOAD

5-Notice

Apply persisted config cmds on reload switched off

The switch that controls the persisted commands applied during reload is set to OFF.

-

"Verify the rommon variable 'logpersistreload' value from rommon" " prompt. This variable might have been intentionally set to OFF."

PARSER-5-CFGLOG_PERSIST_OPER_DOWN

5-Notice

Configuration logger persistency is enabled but is operationally down

When Configuration logger persistency is enabled it is operationally down. It becomes operationally up at the next write memory or copy running-config startup-config operation.

parser

"Please do write memory or copy running-config startup-config" " to make the feature operationally up. Otherwise the" " commands will not be persisted."

PARSER-5-CFGLOG_PERSIST_OPER_UP

5-Notice

Configuration logger persistency is operationally up

When Configuration logger persistency is enabled it becomes operationally up after the next write memory operation to start persisting commands.

parser

"This is a notification message only. No action is required."

PARSER-5-CFGLOG_PERSIST_FILE_LIMIT

5-Notice

Configuration logger persistency contains [dec] commands in [chars] file.

Configuration logger persistency has persisted more commands. Time to do write memory to save all the persisted commands to the startup-config file.

parser

"This is a notification message to remind the user to do" " write memory or copy running-config startup-config."

PARSER-6-LI_VIEW_INIT

6-Information

LI-View initialised.

You have successfully initialised LI-View.

-

""

PARSER-3-REGEXP_COMPILE_ERROR

3-Error

compile of regular expression failed: \[chars]\

Unrecoverable error while parsing

-

"Ensure that the system is not low on memory."

PARSER-3-AFSFAIL

3-Error

[chars] for command serialization failed.

This message indicates that the event required for command serialization has failed.

-

-

PARSER-6-CLIHOG

6-Information

This command by [chars] will not be serialized anymore.

This message indicates that the command execution might be either time consuming or processing large data structures. Attention required by the CLI owners to set PARSE_DONT_FLAG and protect their data structure else ignore.

-

"Please contact the Command Owner to take corrective action."

PARSER-3-CSLFAIL

3-Error

Semaphore creation for configuration session lock failed

This message indicates that the semaphore required for configuration session locking has failed.

-

-

PARSER-6-CSLOCKTIMEOUT

6-Information

Configuration session lock acquired by application '[chars]' / process '[dec]' is being used for long time.

Configuration session lock has been acquired and timed out. The lock should be made available for requesting process.

parser

"This is a notification message in case of manually acquired lock " " by 'configure terminal lock' command. " "A defect can be filed if any other application is blocking it".

PARSER-6-CSLOCKCLEARED

6-Information

Configuration session lock is cleared by process '[dec]' user '[chars]' from terminal '[dec]'

Configuration session lock was forcibly released as per the request by either the terminal user or an application or on timeout.

parser

"This is a notification message only. No action is required."

PARSER-4-SHELL_SYNTAX

4-Warning

Shell function: [chars]: Syntax Error: [chars]

There is a syntax error in the Shell script.

parser

"Users are recommended to correct it in the script."

PARSER-3-WMLFAIL

3-Error

Semaphore creation for write memory lock failed

This message indicates that the semaphore required for write memory locking has failed.

-

-

PARSER-6-WMLRETRY

6-Information

Write memory lock currently held by pid '[dec]' automatic retry.

This message indicates that the semaphore required for write memory locking has timed out.

-

-

PARSER-5-HIDDEN

5-Notice

Warning!!! ' [chars]' is a hidden command. Use of this command is not recommended/supported and will be removed in future.

This message indicates the current cli is hidden command.

-

-

PARSER-5-INTERNAL

5-Notice

Warning!!! ' [chars]' is an internal command. Use of this command is not recommended/supported.

This message indicates the current cli is an internal command.

-

-

PARSER-3-BADSUBCMD

3-Error

Unrecognized subcommand [dec] in [chars] command '[chars]'

The parser failed an internal software check.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ARCHIVE_DIFF-3-DIFF_INIT_FAILED

3-Error

Could not initialize the Config Diff and Rollback subsystem

An internal software error occurred during initialization. Config Diff and Rollback cannot be used as a result of this error.

-

"Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance."

ARCHIVE_DIFF-3-DIFF_CMD_INIT_FAILED

3-Error

Failed to register the special case [chars] command:\[chars]\ during initialization. Config Diff and Rollback cannot be used as a result of this error.

An internal software error occurred during initialization - Config Diff and Rollback cannot be used as a result of this error.

-

"Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER

5-Notice

User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] if session has been idle for %lu minutes

The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER

5-Notice

User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] in %lu minutes

The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL

5-Notice

User: [chars]Priv: [dec] View: [dec]: Rollback Confirmed Change is cancelled due to [chars] failure

Rollback Confirmed Change is normally configured along with other configuration operations such as \config term\ or \config replace\. If those operation failed Rollback Confirmed Change should not be activated.

-

"Remove the error condition and try again later."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM

5-Notice

User: [chars]: Confirm the configuration change

The configuration change is confirmed. The timer for rolling to the previously saved config is cancelled

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW

5-Notice

User: [chars]: Rollback immediately.

Rollback immediately and cancel the timer

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER

5-Notice

User: [chars] Reset Rollback Confirmed Change timeridle to %lu minute

Reset Rollback Confirmed Change timeridle to a new value

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER

5-Notice

User: [chars]: Reset Rollback Confirmed Change timerabsolute to %lu minute

Reset Rollback Confirmed Change timerabsolute to a new value

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP

5-Notice

Backing up current running config to [chars]

The current running config is saved so that when the timer expires if no confirmation has been received from user to confirm what they've configured the system will rollback to the saved config.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER

5-Notice

System will rollback to config [chars] in one minute. Enter \configure confirm\ if you wish to keep what you've configured

Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER

5-Notice

User [chars] on tty [dec] has been idle for %lu minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter \configure confirm\ if you wish to keep what you've configured

Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START

5-Notice

Start rolling to: [chars]

The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved config.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY

5-Notice

Failed to acquire configuration lock. Rollback did not start. Schedule to retry in 5 minutes

Failed to acquire configuration lock. Rollback did not start. In this case retry will be scheduled.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

CNS-3-FAULT

3-Error

[chars]

CNS subsystem has detected an internal exception condition

cns-agents

LOG_STD_ACTION

CNS-3-XML_SEMANTIC

3-Error

[chars]

CNS subsystem has experienced an error while processing the XML \n\ encapsulation of configuration command.

cns_configagent

"The externally supplied XML has errors in it and connot be processed.\n\ See specific message text for an indication as to what the\n\ cause might be. This will possible require the command to be\n\ checked and reissued from the server."

CNS-3-TRANSPORT

3-Error

[chars]

CNS subsystem has experienced a problem contacting an external\n\ application.

cns_agents

"See specific message text for an indication as to what the\n\ cause might be. Check the network configuration and cables to make\n\ sure the remote application is running and the address is accessible"

CNS-3-MEMORY

3-Error

[chars]

CNS subsystem has experienced a problem gettting the required\n\ memory to complete this operation.

cns_agents

"Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\n\ upgrading the memory in the network device may be required."

CNS-3-WARNING

3-Error

[chars]

CNS subsystem has experienced an unexpected condition executing\n\ a set of commands which did not cause a failure but suggests things\n\ did not go totally correctly

cns_agents

"Check the error log for additional information. This is an informational\n\ message and does not necessarily indicate an error did happen."

CNS-5-IOS_UP

5-Notice

-

-

-

-

CNS-5-CONFIG_SUCCESS

5-Notice

SUCCESSFUL_COMPLETION

The configuration download has been applied successfully.

-

"None."

CNS-5-CNS_DHCP_OP43_PROCESS_DONE

5-Notice

PROCESSING DONE

The processing of CNS DHCP Option 43 message succeeded.

-

"None."

CNS-3-CNS_DHCP_OP43_PROCESS_FAILED

3-Error

PROCESSING FAILED

The processing of CNS DHCP Option 43 message failed.

-

"Need to verify the CNS DHCP option 43 message is in correct format.\n\ If not correct it and send this message again."

CNS-6-NO_EVENT_AGENT

6-Information

CNS EVENT AGENT IS NOT CONFIGURED

The cns event agent is not configured. The event that was to be sent to it will be dropped

-

"Configure the cns event agent."

WSMA-5-DHCP_OP43_PROCESS_DONE

5-Notice

PROCESSING DONE

The processing of WSMA DHCP Option 43 message succeeded.

-

"None."

WSMA-3-DHCP_OP43_PROCESS_FAILED

3-Error

PROCESSING FAILED

The processing of WSMA DHCP Option 43 message failed.

-

"Need to verify the WSMA DHCP option 43 message is in correct format.\n\ If not correct it and send this message again."

HA_CONFIG_SYNC -3-IPC

3-Error

IPC operation failed for [ [chars] ] with error code [ [chars] ]

A config sync error occurred. The details about\n\ what was attempted and what went wrong will be printed.

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-LBL_POLICY

3-Error

[chars]

Active and Standby configuration out of sync LBL\n\ what was attempted and what went wrong will be printed.

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-LBL_CFGSYNC

3-Error

[chars]

Line by Line sync failure what was attempted and what went wrong \n\ will be printed.

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-FS_BULK_CFGSYNC

3-Error

[chars] [[chars]]

Bulk config sync filesys failure the reason for the failure will be provided in the string

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-BULK_CFGSYNC

3-Error

[chars]

Bulk config sync failure the reason for the failure will be provided in the string

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-GENERAL

3-Error

[chars]

General Config Sync Problem

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC-3-BOOTVAR

3-Error

Cannot communicate boot variable to standby [chars]

Active failed to send the boot variable specified to standby. A reload or a switchover operation will likely result in the standby booting a wrong image.

config-sync

LOG_STD_ACTION

HA_CONFIG_SYNC-3-CONFREG

3-Error

Cannot communicate config register to standby

Active failed to send the config register to standby. The active and standby supervisors won't have the same config registers.

config-sync

LOG_STD_ACTION

HA_CONFIG_SYNC -3-ISSU_REG

3-Error

[chars] with error code [ [chars] ]

An ISSU Config Sync Registration Error occurred. The details about\n\ what was attempted and what went wrong will be printed.

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-ISSU_MTU

3-Error

CONFIG SYNC Failed to get MTU Size for session[[dec]] msg_type[[dec]] MTU[[dec]] rc[[dec]]

An ISSU Config Sync failed to get Messge MTU. The details about\n\ what was attempted and what went wrong will be printed.

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -3-ISSU_XFORM

3-Error

CONFIG SYNC [chars] msg_type[[dec]] rc[[dec]]

An ISSU Config Sync failed to transform messge. The details about\n\ what was attempted and what went wrong will be printed.

config-sync

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

HA_CONFIG_SYNC -6-LBL_PRC_SUBCODE

6-Information

CONFIG SYNC : Subcode not matching for command [chars] Active subcode[0x[hec]] Standby subcode[0x[hec]]

The line by line synchronization of a command has succeeded. A command entered on the active system was successfully synchronized with the standby system. However the sub code of Parser Return Code that were returned by the Active and Standby systems were different. However the sub code of Parser Return Code that were returned by the Active and Standby systems where different.

config-sync

"Normally no action is required. If however any " "problems with line by line synchronization are found " "copy this message exactly as it appears on the console " "or in the system log and contact your Cisco technical " "support representative."

HA_CONFIG_SYNC -6-BULK_CFGSYNC_SUCCEED

6-Information

Bulk Sync succeeded

Bulk Sync has succeeded

config-sync

"No action necessary"

ARCHIVE_ISSU-2-INIT

2-Critical

Archive ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Archive ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

parser

LOG_STD_ACTION

ARCHIVE_ISSU-3-TRANSFORM_FAIL

3-Error

Archive ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Archive ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Archive state between the active device and the standby device is not identical.

parser

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ARCHIVE_ISSU-3-MSG_NOT_OK

3-Error

Archive ISSU client 'Message Type [dec]' is not compatible

The Archive ISSU client received an incompatible message from the peer device. The message cannot be processed.

parser

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ARCHIVE_ISSU-3-MSG_SIZE

3-Error

Archive ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Archive ISSU client failed to calculate the MTU for the specified message. The Archive ISSU client is not able to send the message to the standby device.

parser

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ARCHIVE_ISSU-3-INVALID_SESSION

3-Error

Archive ISSU client does not have a valid registered session.

The Archive ISSU client does not have a valid registered session.

parser

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ARCHIVE_ISSU-2-SESSION_REGISTRY

2-Critical

Archive ISSU client failed to register session information. Error: [dec] [chars]

The Archive ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

parser

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ARCHIVE_ISSU-3-SESSION_UNREGISTRY

3-Error

Archive ISSU client failed to unregister session information. Error: [dec] [chars]

The Archive ISSU client failed to unregister session information.

parser

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ARCHIVE_ISSU-2-SESSION_NEGO_FAIL_START

2-Critical

Failed to start Archive ISSU session negotiation. Error: [dec] [chars]

The Archive ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly.

parser

"show issu session <client_id>"

ARCHIVE_ISSU-2-SEND_NEGO_FAILED

2-Critical

Archive ISSU client failed to send negotiation message. Error: [dec] [chars]

The Archive ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

parser

"show logging and show checkpoint client"

ARCHIVE_ISSU-2-GET_BUFFER

2-Critical

Archive ISSU client failed to get buffer for message. Error: [dec] [chars]

The Archive ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

parser

"show logging and show checkpoint client"

ARCHIVE_CONFIG-4-ARCHIVE_SKIPPED

4-Warning

Archive of router configuration was skipped due to a previous initiation.

Only one archive can be created at a time. Two or more simultaneous archives in progress is not allowed. This could occur for example if two users attempt to create an archive simultaneouly.

-

"Retry the archive creation later when the previous archive has finished being written."

ARCHIVE_CONFIG-4-ARCHIVE_DELETE_FAILED

4-Warning

Delete of a previously saved archive of the router configuration could not be completed.

The router could not delete a file that was previously written. The file that was being deleted file contains an archive of the router configuration. This could occur for example if the file was manually deleted.

-

"None"

ARCHIVE_CONFIG-6-ARCHIVE_CREATE_FAILED_STANDBY

6-Information

Could not create an archive of the router configuration on the standby RP.

The router could not create an archive file on the standby RP. The file that was being created contains an archive of the router configuration. This could occur for example if the active RP cannot communicate with the standby RP.

-

"None"

ARCHIVE_CONFIG-6-ARCHIVE_DELETE_FAILED_STANDBY

6-Information

Delete of a previously saved archive of the router configuration could not be completed on the standby RP.

The router could not delete a file that was previously written on the standby RP. The file that was being deleted file contains an archive of the router configuration. This could occur for example if the file was manually deleted. Alternatively the file could not be deleted when the active RP cannot communicate with the standby RP.

-

"None"

ARCHIVE_DIFF-3-DIFF_INIT_FAILED

3-Error

Could not initialize the Config Diff and Rollback subsystem

An internal software error occurred during initialization. Config Diff and Rollback cannot be used as a result of this error.

-

"Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance."

ARCHIVE_DIFF-3-DIFF_CMD_INIT_FAILED

3-Error

Failed to register the special case [chars] command:\[chars]\ during initialization. Config Diff and Rollback cannot be used as a result of this error.

An internal software error occurred during initialization - Config Diff and Rollback cannot be used as a result of this error.

-

"Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER

5-Notice

User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] if session has been idle for %lu minutes

The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER

5-Notice

User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] in %lu minutes

The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL

5-Notice

User: [chars]Priv: [dec] View: [dec]: Rollback Confirmed Change is cancelled due to [chars] failure

Rollback Confirmed Change is normally configured along with other configuration operations such as \config term\ or \config replace\. If those operation failed Rollback Confirmed Change should not be activated.

-

"Remove the error condition and try again later."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM

5-Notice

User: [chars]: Confirm the configuration change

The configuration change is confirmed. The timer for rolling to the previously saved config is cancelled

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW

5-Notice

User: [chars]: Rollback immediately.

Rollback immediately and cancel the timer

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER

5-Notice

User: [chars] Reset Rollback Confirmed Change timeridle to %lu minute

Reset Rollback Confirmed Change timeridle to a new value

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER

5-Notice

User: [chars]: Reset Rollback Confirmed Change timerabsolute to %lu minute

Reset Rollback Confirmed Change timerabsolute to a new value

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP

5-Notice

Backing up current running config to [chars]

The current running config is saved so that when the timer expires if no confirmation has been received from user to confirm what they've configured the system will rollback to the saved config.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER

5-Notice

System will rollback to config [chars] in one minute. Enter \configure confirm\ if you wish to keep what you've configured

Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER

5-Notice

User [chars] on tty [dec] has been idle for %lu minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter \configure confirm\ if you wish to keep what you've configured

Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START

5-Notice

Start rolling to: [chars]

The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved config.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY

5-Notice

Failed to acquire configuration lock. Rollback did not start. Schedule to retry in 5 minutes

Failed to acquire configuration lock. Rollback did not start. In this case retry will be scheduled.

-

"This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change."

ROLLBACK_ISSU-2-INIT

2-Critical

Rollback ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Rollback ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

parser

LOG_STD_ACTION

ROLLBACK_ISSU-3-TRANSFORM_FAIL

3-Error

Rollback ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Rollback ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Rollback state between the active device and the standby device is not identical.

parser

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ROLLBACK_ISSU-3-MSG_NOT_OK

3-Error

Rollback ISSU client 'Message Type [dec]' is not compatible

The Rollback ISSU client received an incompatible message from the peer device. The message cannot be processed.

parser

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ROLLBACK_ISSU-3-MSG_SIZE

3-Error

Rollback ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Rollback ISSU client failed to calculate the MTU for the specified message. The Rollback ISSU client is not able to send the message to the standby device.

parser

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ROLLBACK_ISSU-3-INVALID_SESSION

3-Error

Rollback ISSU client does not have a valid registered session.

The Rollback ISSU client does not have a valid registered session.

parser

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ROLLBACK_ISSU-2-SESSION_REGISTRY

2-Critical

Rollback ISSU client failed to register session information. Error: [dec] [chars]

The Rollback ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

parser

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ROLLBACK_ISSU-3-SESSION_UNREGISTRY

3-Error

Rollback ISSU client failed to unregister session information. Error: [dec] [chars]

The Rollback ISSU client failed to unregister session information.

parser

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ROLLBACK_ISSU-2-SESSION_NEGO_FAIL_START

2-Critical

Failed to start Rollback ISSU session negotiation. Error: [dec] [chars]

The Rollback ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly.

parser

"show issu session <client_id>"

ROLLBACK_ISSU-2-SEND_NEGO_FAILED

2-Critical

Rollback ISSU client failed to send negotiation message. Error: [dec] [chars]

The Rollback ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

parser

"show logging and show checkpoint client"

ROLLBACK_ISSU-2-GET_BUFFER

2-Critical

Rollback ISSU client failed to get buffer for message. Error: [dec] [chars]

The Rollback ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

parser

"show logging and show checkpoint client"

PARSE_RC-6-PRC_ENABLE

6-Information

Parser PRC Feature Enabled. PRC logs are displayed for configuration commands alone

Parser PRC Feature Enabled. PRC logs are displayed for configuration commands alone

parser

"LOG_STD_NO_ACTION"

PARSE_RC-6-PRC_DISABLE

6-Information

Parser PRC Feature Disabled

Parser PRC Feature Disabled

parser

"LOG_STD_NO_ACTION"

PARSE_RC-3-PRC_LEV_RANGE

3-Error

Parser Return Code level range error [dec]

An internal software error occurred.

-

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

PARSE_RC-3-PRC_SUBRCODE_RANGE

3-Error

Parser Return Code state range error [dec]

An internal software error occurred.

-

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

PARSE_RC-3-PRC_INVALID_CSB

3-Error

-

An internal software error occurred.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_INVALID_BLOCK_PTR

3-Error

-

An internal software error occurred.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_OUT_OF_RANGE_ENUM

3-Error

[chars] had value [dec]

An out-of-range parameter was passed to an internal API.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_UNRECOGNIZED_ERROR

3-Error

error value `[dec]' is not currently mapped

An unrecognized error was caught and remapped.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_INTERRUPT

3-Error

[chars]

An internal software error occurred.

parser

LOG_STD_ACTION

PARSE_RC-4-PRC_NON_COMPLIANCE

4-Warning

`[chars]'

An internal software error occurred.

parser

LOG_STD_ACTION

SHELL_ISSU-2-INIT

2-Critical

Shell ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Shell ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

parser

LOG_STD_ACTION

SHELL_ISSU-3-MSG_NOT_OK

3-Error

Shell ISSU client 'Message Type [dec]' is not compatible

The Shell ISSU client received an incompatible message from the peer device. The message cannot be processed.

parser

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SHELL_ISSU-3-MSG_SIZE

3-Error

Shell ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Shell ISSU client failed to calculate the MTU for the specified message. The Shell ISSU client is not able to send the message to the standby device.

parser

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SHELL_ISSU-3-INVALID_SESSION

3-Error

Shell ISSU client does not have a valid registered session.

The Shell ISSU client does not have a valid registered session.

parser

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SHELL_ISSU-2-SESSION_REGISTRY

2-Critical

Shell ISSU client failed to register session information. Error: [dec] [chars]

The Shell ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

parser

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SHELL_ISSU-3-SESSION_UNREGISTRY

3-Error

Shell ISSU client failed to unregister session information. Error: [dec] [chars]

The Shell ISSU client failed to unregister session information.

parser

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SHELL_ISSU-2-SESSION_NEGO_FAIL_START

2-Critical

Failed to start Shell ISSU session negotiation. Error: [dec] [chars]

The Shell ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly.

parser

"show issu session <client_id>"

SHELL_ISSU-2-SEND_NEGO_FAILED

2-Critical

Shell ISSU client failed to send negotiation message. Error: [dec] [chars]

The Shell ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

parser

"show logging and show checkpoint client"

SHELL_ISSU-2-GET_BUFFER

2-Critical

Shell ISSU client failed to get buffer for message. Error: [dec] [chars]

The Shell ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

parser

"show logging and show checkpoint client"

SHELL_ISSU-2-COPY_SHELL_INIT_TO_STANDBY

2-Critical

Failed to copy the shell init file [chars] to standby

If the shell init file is not copied to standby the shell init file CLI will not be applied to maintain the consistancy between active and standby.

parser

"Try manually copy a file to standby to see if it's" " a filesystem issue. It could be a space issue in the" " standby disk"

SHELL_ISSU-2-SAVE_TRIGGER_FOR_REAPPLY

2-Critical

Failed to add trigger to the re-apply queue. Trigger: [chars] Env: [chars]

Triggers that failed to get applied during ISSU must be saved and then re-applied after ISSU completes.

parser

"Manually re-apply the trigger after ISSU completes"

NETCONF-3-MEMORY

3-Error

[chars]

Netconf subsystem has experienced a problem gettting the required\n\ memory to complete this operation.

netconf

"Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\n\ upgrading the memory in the network device may be required."

SEP-3-MEMORY

3-Error

[chars]

Sep subsystem has experienced a problem gettting the required\n\ memory to complete this operation.

sep

"Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\n\ upgrading the memory in the network device may be required."

LOGGING_REDIRECT_ISSU-2-INIT

2-Critical

Logging Redirect ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Logging Redirect ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

logging-redirect

LOG_STD_ACTION

LOGGING_REDIRECT_ISSU-3-TRANSFORM_FAIL

3-Error

Logging Redirect ISSU client [chars] transform failed for Message Type [dec] . Error: [dec] [chars]

The Logging Redirect ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Logging Redirect state between the active device and the standby device is not identical.

logging-redirect

"show issu session <client_id> and " "show issu negotiated version <session_id>"

LOGGING_REDIRECT_ISSU-3-MSG_NOT_OK

3-Error

Logging Redirect ISSU client Message Type [dec] is not compatible

The Logging Redirect ISSU client received an incompatible message from the peer device. The message cannot be processed.

logging-redirect

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

LOGGING_REDIRECT_ISSU-3-MSG_SIZE

3-Error

Logging Redirect ISSU client failed to get the MTU for Message Type [dec] . Error: [dec] [chars]

The Logging Redirect ISSU client failed to calculate the MTU for the specified message. The Logging Redirect ISSU client is not able to send the message to the standby device.

logging-redirect

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

LOGGING_REDIRECT_ISSU-3-INVALID_SESSION

3-Error

Logging Redirect ISSU client does not have a valid registered session.

The Logging Redirect ISSU client does not have a valid registered session.

logging-redirect

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

LOGGING_REDIRECT_ISSU-2-SESSION_REGISTRY

2-Critical

Logging Redirect ISSU client failed to register session information. Error: [dec] [chars]

The Logging Redirect ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

logging-redirect

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

LOGGING_REDIRECT_ISSU-3-SESSION_UNREGISTRY

3-Error

Logging Redirect ISSU client failed to unregister session information. Error: [dec] [chars]

The Logging Redirect ISSU client failed to unregister session information.

logging-redirect

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

LOGGING_REDIRECT_ISSU-2-SESSION_NEGO

2-Critical

Logging Redirect ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Logging Redirect ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

logging-redirect

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

LOGGING_REDIRECT_ISSU-2-SEND_NEGO_FAILED

2-Critical

Logging Redirect ISSU client failed to send negotiation message. Error: [dec] [chars]

The Logging Redirect ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

logging-redirect

"show logging and show checkpoint client"

LOGGING_REDIRECT_ISSU-2-GET_BUFFER

2-Critical

Logging Redirect ISSU client failed to get buffer for message. Error: [dec] [chars]

The Logging Redirect ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

logging-redirect

"show logging and show checkpoint client"

XOS-7-XOS_ONINT

7-Debug

XOS APIs cannot be called in a interrupt path

An XOS API was called in the interrupt path this is currently not supported.

infra-xoslib

"Please check your code and avoid using this API in the interrupt path"

XOS-7-XOS_DM_WAIT

7-Debug

xos_dm_wait API cannot be called by a process that does not own the XDM xdm pid: [dec] current pid: [dec]

The xos_dm_wait API was called by a process that is not the owner of that \n XDM. Only process that create the XDM instance can own it.

infra-xoslib

"Please check your code and avoid invoking this API in a different process \n" "context."

XOS-7-XOS_DM_DISPATCH

7-Debug

xos_dm_dispatch API cannot be called that does not own the XDM xdm pid: [dec] current pid: [dec]

The xos_dm_dispatch API was called by a process that is not the owner of \n that XDM. Only process that create the XDM instance can own it.

infra-xoslib

"Please check your code and avoid invoking this API in a different process \n" "context."

XOS-7-XOS_DM_XDISPATCH

7-Debug

xos_dm_xdispatch API cannot be called that does not own the XDM xdm pid: [dec] current pid: [dec]

The xos_dm_xdispatch API was called by a process that is not the owner of \n that XDM. Only process that create the XDM instance can own it.

infra-xoslib

"Please check your code and avoid invoking this API in a different process \n" "context."

XOS-7-XOS_STUCK_TMR

7-Debug

XOS timer expired earlier than expected expiration time tree:%p time:[dec].[dec]

The XOS timer handler was invoked earlier than expiration value of the \n timer

infra-xoslib

"Please check expiration timer value set on the timer. Also some OS \n" "infrastructures can roundup expiration time so that timer handler gets \n" "invoked earlier than expected "

ISSU_PROCESS-3-LOADVERSION

3-Error

[chars]

The ISSU commitversion command did not fulfill the necessary criteria. This can happen due to the following conditions not being met. \n1. Current ISSU state is not RunVersion \n2. Secondary Version doesn't exist on Standby \n3. Standby BOOT variable doesn't exist \n4. The new image is not the first in BOOT on Standby \n5. Active BOOT variable is not set \n6. Primary Version on Active doesn't exist \n7. New image is not the first in Active BOOT \n8. Configuration register is not 0x2102

install

"Fix the error and try the command again"

ISSU_PROCESS-3-ABORTVERSION

3-Error

issu abortversion: [chars]

The ISSU abortversion command can be run only from the LoadVersion or RunVersion state

install

"Please proceed to reinitializing the ISSU process"

ISSU_PROCESS-6-SELF_RELOAD

6-Information

slot [dec] countdown to self-reload started [dec] second delay\n

Self reload from Upgrade Director's instructions

install

"Log the circumstances"

ISSU_PROCESS-6-SELF_RELOAD_CANCEL

6-Information

Self-reload cancelled on slot [dec]\n

Cancel of self-reload from user 'abort' instruction

install

"Log the circumstances"

ISSU_PROCESS-6-LOADVERSION_INFO

6-Information

[chars]

Provides the issu state information

install

"Observe the status message"

ISSU_PROCESS-6-RUNVERSION_INFO

6-Information

[chars]

Provides the issu state information

install

"Observe the status message"

ISSU_PROCESS-6-COMMITVERSION_INFO

6-Information

[chars]

Provides the issu state information

install

"Observe the status message"

ISSU_PROCESS-3-ABORT

3-Error

[chars]

Provides abort status information

install

"Observe the status message"

ISSU_PROCESS-3-PRST

3-Error

[chars]

Persistent variables are not set properly.

install

"The issu commands or the hw-module command did not " "set the variables properly."

ISSU_PROCESS-3-NVRAM

3-Error

[chars]

NVRAM variables are not set properly.

install

"The issu commands or the hw-module command did not " "set the variables properly."

ISSU_PROCESS-3-SYSTEM

3-Error

[chars]

The configuration register value should not be changed while the ISSU process is in progress

install

"The low order byte of the configuration register " "should be 0x02 during the upgrade process"

ISSU_PROCESS-3-PARAMETERS

3-Error

[chars] [chars] parameters are wrong

The system could not be configured for ISSU

install

"Fix the error and try the command again"

ISSU_PROCESS-3-FILESYS

3-Error

'[chars]' filesystem does not exist\n

Verification of the filesystem failed

install

"The file needs to be downloaded to the flash disk"

ISSU_PROCESS-7-DEBUG

7-Debug

[chars]

Debug commands for the ISSU process. The system is \nattempting to recover from an unknown error.\n

install

"Send the output of 'show logging' to TAC for " "debugging purposes."

ISSU_PROCESS-3-ROLLBACK_TIMER

3-Error

[chars]

The rollback timer could not be configured

install

"Fix the error and try the command again"

ISSU_PROCESS-4-ACCEPTVERSION_WARNING

4-Warning

ISSU auto-rollback will be initiated in [dec] minutes.

It shows the warning message several minutes before the expiration of rollback timer

install

"Issue the acceptversion command before the " "expiration of rollback timer"

ISSU_PROCESS-3-RF

3-Error

[chars] [ [chars] ]

The ISSU process RF client had an error.

install

"Copy the error and send it to TAC."

ISSU_PROCESS-3-IPC_AGENT

3-Error

[chars] [ [chars] ]

The ISSU process IPC agent had an error.

install

"Copy the error and send it to TAC."

ISSU_PROCESS-3-IPC_MSG

3-Error

[chars]

The ISSU process IPC MSG Queue Setup encountered an error.

install

"Copy the error and send it to TAC."

ISSU_PROCESS-3-TRANSFORM

3-Error

[chars] [ [chars] ]

The ISSU process transform utility had an error.

install

"Send the output of 'show version' from the Active " "and the Standby and send it to TAC."

ISSU_PROCESS-3-PEER

3-Error

[chars]

The ISSU process cannot continue with negotiation as it can't verify the peer's state.\n

install

"Make sure the peer is present and try again.\n" "If the problem persists send the output of " "'show issu state' and 'show version' to TAC."

ISSU_PROCESS-3-IMAGE

3-Error

[chars] is loading the wrong image [ [chars] ] expected image [ [chars] ]

Wrong image is being loaded during ISSU process.

install

"Check the detail state of ISSU process make sure " "the right images are loaded on Active and " "on Standby"

ISSU_PROCESS-3-UAM

3-Error

[chars] [chars]

Return code failure from calling UAM API.

install

"Got unexpected rc from calling UAM API."

ISSU_PROCESS-4-ABORT_ISSU

4-Warning

[chars]

The peer has been determined to be incompatible and hence is being reloaded.

install

"Send the output of 'show redundancy history' from " "the Active to TAC."

RF-3-NOTIF_TMO

3-Error

Notification timer Expired for RF Client: [chars][dec]

As part of the progression the client had previously indicated to RF that it has work to do by returning RF_OK but it did not complete the work or respond to RF within the notification time.

redundancy-rf

"show redundancy history"

RF-3-NOTIF_TID

3-Error

Notification timer extended for the wrong client cur-client=[dec] req-client=[dec]

The current RF client has attempted to extend the RF notification timer using a client ID other than its own. This is an internal software error. The message text on the console or in the system log contains the error details such as the current client ID number and the requested client ID number.

redundancy-rf

"show redundancy history"

RF-5-RF_TERMINAL_STATE

5-Notice

Terminal state reached for [chars]

RF has reached a terminal state for the operating mode.

-

"This is a notification message only. No action is required."

RF-5-SEND_FAIL

5-Notice

RF client progression send failure for reason [chars]

RF has failed to send a client progression to the standby client.

redundancy-rf

"show redundancy history"

RF-5-RF_RELOAD

5-Notice

[chars]. Reason: [chars]

RF has invoked a reload.

redundancy-rf

"show redundancy history reload"

RF-3-MALLOC_FAILURE

3-Error

[chars]

Memory allocation failure

redundancy-rf

"Gather redundancy-ha_mgr log and send it to TAC"

RF-3-MSG_SEND_FAILURE

3-Error

[chars]

Message send between internal RF modules failed.

redundancy-rf

"Gather redundancy-ha_mgr log and send it to TAC"

RESETMGR-3-RESET

3-Error

Reset Manager has reset the system due to \'[chars]\' process restart

Reset Manager stores a set of IDs each one of these IDs uniquely identify a process on the system. If one of these monitored processes is restarted the Standby unit will be reset so that the versioning infrastructure can renegotiate. This is not a software fault the Standby system is being forced to reset by the Reset Manager.

resetmgr

LOG_STD_NO_ACTION

RESETMGR-3-RESET_UNKNOWN

3-Error

A restarted process could not be identified by its Job ID the Reset Manager has reset the Standby system.

Reset Manager stores a set of IDs each one of these IDs uniquely identifies a process on the system. A process was restarted but it could not be uniquely identified via it Job ID. It is possible that the restarted process was being monitored by the Reset Manager but since we cannot be sure the Standby system is being reset. This is most likely due to a software fault on the system.

resetmgr

LOG_STD_NO_ACTION

RESETMGR-3-NOMEM

3-Error

Failed to allocate memory to add ID [dec] to table

Reset Manager was unable to allocate memory to add the unique ID and process name to its table. If this process is restarted on the Active system the Standby system may not be reset due to this error.

resetmgr

"show tech"

RESETMGR-4-SYSMGR_PROCNAME_LOOKUP

4-Warning

Failed to lookup process name from SysMgr job ID = [dec]

Reset Manager was unable to get the name of the process with the specified job ID from SysMgr. This is a SysMgr error however the system can continue to operate normally as the process name is only used for reference purposes.

resetmgr

"show tech"

RESETMGR-3-SYSMGR_JOBID_LOOKUP

3-Error

Failed to get the job ID of the Reset Manger IOS blob from SysMgr

Reset Manager was unable to get it's job ID same as IOS blob from

resetmgr

"show tech"

COMP_MATRIX-4-DISABLED

4-Warning

Compatibility Matrix has been disabled. No image compatibility checking will be done.

The ISSU compatibility matrix check has been disabled via configuration command <cmdBold>no service image-version compatibility<noCmdBold>. When the standby comes up no image compatibility checking will be done which results in SSO redundancy mode even if the active and standby are running different images.

ha-issu-infra

"The ISSU compatibility matrix check has been disabled " "using the global configuration command " "<cmdBold>no service image-version compatibility<noCmdBold>." "Redundancy mode would be SSO. " "Please be sure this is your intention or change configuration " "using <cmdBold>service image-version compatibility<noCmdBold>."

COMP_MATRIX-3-PRST_VBL_GET

3-Error

ISSU Compatibility Matrix was unable to read a persistent variable from the local system rc = [dec].

The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled.

ha-issu-infra

"show persistent variable"

COMP_MATRIX-3-PRST_VBL_DELETE

3-Error

ISSU Compatibility Matrix was unable to delete a persistent variable from the [chars] system rc = [dec].

The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled.

ha-issu-infra

"show persistent variable"

COMP_MATRIX-3-PRST_VBL_WRITE

3-Error

ISSU Compatibility Matrix was unable to write to persistent variables on the [chars] system rc = [dec].

The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled.

ha-issu-infra

"show persistent variable"

FORCE_RPR-3-RF_REGISTER

3-Error

RF error = [dec]. [chars]

During system initialization Force RPR component was unable to register with the Redundancy Facility.

redundancy-rf

LOG_STD_ACTION FORCE_RPR_STD_ACTION

FORCE_RPR-3-PEER_OPER_MODE

3-Error

Peer node has reset [dec] times. [chars]

The peer node has reset the maximum number allowed before reaching STANDBY-HOT state. The 'redundancy force-rpr' command is enabled and will try to set the peer system to RPR operating mode.

redundancy-rf

LOG_STD_ACTION FORCE_RPR_STD_ACTION

FORCE_RPR-4-NOT_ON_ACTIVE

4-Warning

[chars]

Only the Active node may enable this feature. Make sure you're on the Active system before trying to enable this command

redundancy-rf

LOG_STD_ACTION FORCE_RPR_STD_ACTION

CHKPT-3-REGISTERATION_FAILED

3-Error

Failed to register with [chars] rc = [dec]

An internal failure associated with client registration occurred in the run-time module specified in the message output. The return code that is specified in the message output identifies the type of failure that was detected. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-3-NO_RESOURCES

3-Error

[chars]

A run-time module could not obtain the resources that are required to complete a task. The failure most likely occurred because of a software error or a lack of system memory. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

checkpoint

"If you determine that this condition was caused by a lack of system " "memory reduce system activity to ease memory demands or if conditions " "warrant upgrade to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION

CHKPT-3-IPCPORT

3-Error

Unable to create IPC port on [chars]

A severe checkpoint error occurred because the system was unable to allocate the resources needed to create a communications port for the Interprocess Communications IPC channel needed to

checkpoint

"Increase the memory. If the error persists" LOG_STD_SH_TECH_ACTION

CHKPT-3-IPCREGISTER

3-Error

Unable to register IPC port on [chars]

Checkpoint Facility was unable to register an IPC port. This can happen when registering a port that hasn't yet been created.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-NOIPCPORT

4-Warning

IPC port is NULL [chars]

Checkpoint Facility cannot send the message as the IPC port information is NULL. This message appears since since the communication session between the Checkpointing Facility peers has not yet been established.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-3-RMI_FAILED

3-Error

Checkpointing Facility failed to register with the Resource Manager RMI [chars]

Checkpointing Facility registers with the Resource Manager RMI to

checkpoint

"show tech"

CHKPT-3-RMI_CALLBACK

3-Error

Checkpointing Facility encountered an error while processing a callback from the Resource Manager RMI [chars]

Checkpointing Facility registers with the Resource Manager RMI to

checkpoint

"show tech"

CHKPT-4-NOCLIENT

4-Warning

CF client is NULL [chars]

Checkpoint Facility cannot send the message as the client is NULL.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-NOMESSAGE

4-Warning

Message is NULL [chars]

Checkpoint Facility cannot send the message as the message is NULL.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-3-IPCSESSION

3-Error

Unable to open an IPC session with [chars]

A severe checkpointing error occured as the system was unable to establish an interprocess communications session between the Active and the Standby peers.

checkpoint

"As this failure hinders any communication from taking place " "between the Active and the Standby peers reset the Standby. " "If the error persists" LOG_STD_SH_TECH_ACTION

CHKPT-3-RFREG

3-Error

Unable to register checkpoint as client of RF.

This is a severe error as far as check pointing is concerned

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-INVALID_CLIENT

4-Warning

Invalid checkpoint client ID [dec].

The client id is invalid. This error has occured since the corresponding client is not present.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-INVALID_ENTITY

4-Warning

Invalid checkpoint entity ID [dec].

The entity id is invalid. This error has occured since the corresponding entity is not present.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-DUPID

4-Warning

Duplicate checkpoint client ID [dec].

A checkpoint client is using a client ID which is already assigned to an another client. This could be due to a synchronization delay which will typically resolve itself. This would happen when an already registered Checkpointing Facility client again tries to add itself.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-3-NOMEM

3-Error

Unable to allocate resources for CF on [chars].

This error occurs when there are no memory resources available. This is a severe error as far as check pointing is concerned

checkpoint

"Reduce other system activity to ease memory demands. Add more memory. " "If enough memory is available try to see whether the problem goes away " "by reloading the router. If not then" LOG_STD_SH_TECH_ACTION

CHKPT-3-ILLEGAL

3-Error

ILLEGAL call to CF API by client [dec] on the [chars] system

An illegal API call was made by a CF client

checkpoint

"Find out the offending client using " LOG_STD_SH_TECH_ACTION

CHKPT-3-UNKNOWNMSG

3-Error

Unknown message received from peer on the standby for client [dec].

This is a severe error as far as check pointing is concerned. This will be caused when one of the peers can some checkpoint message types that the other side does not understand. This is caused due to a software error as the set of messages being exchanged by either side must be the same.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-DISABLED

4-Warning

Check Pointing is disabled. Client [chars] should not be calling any CF API

This is mainly a warning and might be due to timing issue

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-3-TRANSMIT_FAILED

3-Error

Checkpointing message transmission failure [chars]

-

-

-

CHKPT-3-ISSU_MSG_NOT_COMPATIBLE

3-Error

Checkpointing message type not compatible

Checkpointing messages are used to carry encoded information for transfer between various High-Availabilty clients. For example to synchronize state information between redundant route processor units. An error was detected when verifying the checkpointing message type compatibility between checkpointing client peers. The failure most likely occurred because of a software error. The system state between one or more checkpointing clients might not be properly synchronized.

checkpoint

"show checkpoint client"

CHKPT-3-ISSU_RCV_TRANSFORM_FAILED

3-Error

Checkpointing receive message header transformaton failed [chars]

-

-

-

CHKPT-3-ISSU_XMIT_TRANSFORM_FAILED

3-Error

Checkpointing transmit message header transformaton failed [chars]

-

-

-

CHKPT-3-ISSU_NEGO_FAILED

3-Error

Checkpointing Facility failed to start ISSU negotiation with the peer [chars]

Checkpointing Facility was unable to start the ISSU negotiation successfully. ISSU negotiation is done during system initialization or if the Standy system is signing in with the Active system. The failure to start negotiation is a fatal error condition and most likely occured because of a software error.

checkpoint

"show tech"

CHKPT-4-GET_BUFFER

4-Warning

Checkpointing ISSU failed to get buffer. Dest seat id 0x[hec]

Checkpointing ISSU failed to get a buffer. This is due to the dearth of memory resources.

checkpoint

"Upgrade the memory. If the error " "persists " LOG_STD_SH_TECH_ACTION

CHKPT-4-FREE_BUFFER

4-Warning

Checkpointing [dec] failed to free buffer

Checkpointing failed to free a buffer. This may cause leak in memory resources.

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-MSG_SEND

4-Warning

Checkpointing ISSU failed to send message. Dest seat id 0x[hec]

Checkpointing ISSU failed to send nego message to peer. This will be due to an out of memory condition communication with the peer being severed

checkpoint

LOG_STD_SH_TECH_ACTION

CHKPT-4-INIT

4-Warning

Checkpoint [chars] initialization failed in RF state [chars]

Checkpointing initialization has failed This is software error caused by an out of memory condition as there aren't enough resources available to set up the initialization data structures

checkpoint

"Upgrade the memory. If the error " "persists " LOG_STD_ACTION

CHKPT-3-INVALID_CALLBACK_ARG

3-Error

Attempt to add a checkpointing client with an invalid [chars] argument

Checkpointing messages are used to carry encoded information for transfer between various High-Availabilty clients. For example to synchronize state information between redundant route processor units. An invalid argument was supplied to an internal API. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred. The system state between one or more checkpointing clients might not be properly synchronized.

checkpoint

LOG_STD_ACTION

CHKPT-3-TIMER

3-Error

[chars]

Checkpoint Facility was unable to retrieve the correct context for a previously saved message descriptor. This is most likely a software error caused by possible memory corruption.

checkpoint

LOG_STD_ACTION

CHKPT-4-PAK_RECLAIM

4-Warning

Failed to reclaim packet from Packet Manager client [chars]

After the message send failed the CF client was unable to reclaim the packet to be able to free the message.

checkpoint

LOG_STD_ACTION

CHKPT-4-PAK_MGR_CONN

4-Warning

Failed to connect to the Packet Manager

During Checkpoint initialization unable to create a connection to the Packet Manager. This could result in the CF infra unable to access shared memory in the client context using a virtual address.

checkpoint

LOG_STD_ACTION

CHKPT-3-CHKPT_MSG_NULL

3-Error

The chkpt message has an empty data buffer

This is a severe error as far as checkpointing is concerned. The chkpt message's data buffer is NULL indicating that there were no memory resources to assign while getting a buffer.

checkpoint

"Check whether this error goes away when the " "memory is increased else " LOG_STD_SH_TECH_ACTION

CHKPT-3-SYSMGR_LOOKUP

3-Error

Failed to get process Job ID from SysMgr

Failed to get the Job ID for this ION process from SysMgr. The

checkpoint

"show tech"

CHKPT-3-INVALID_ENTITY_MSG_ID

3-Error

Invalid message event received [dec]

-

-

-

CHKPT-5-HIGHBUFFER

5-Notice

Checkpoint client using Large No. of Buffers in domain [dec] are [chars]

Several IPC messages are pending to be processed by or delevered to

checkpoint

"show checkpoint statistics buffer-usage"

RED_MODE-3-NO_REGISTER

3-Error

Could not register plugin for redundancy mode [chars]

At system initialisation the plugin that describes the capabilities of this redundancy mode could not be registered with the redundancy mode client. This redundancy mode may not be available as an option from the parser.

ha-red-mode-client

LOG_STD_ACTION

RED_MODE-3-NO_REGISTER_IN_DOMAIN

3-Error

Could not register plugin for redundancy mode [chars] in domain [dec]

At system initialisation the plugin that describes the capabilities of this redundancy mode could not be registered with the redundancy mode client in the given domain. This redundancy mode may not be available as an option from the parser.

ha-red-mode-client

LOG_STD_ACTION

RED_MODE-3-NO_DEREGISTER

3-Error

Could not deregister plugin for redundancy mode [chars]

At system initialisation the plugin that describes the capabilities of this redundancy mode could not be deregistered with the redundancy mode client.

ha-red-mode-client

LOG_STD_ACTION

RED_MODE-3-DELAYED_REGISTER

3-Error

Delayed registration could not be completed succesfully Operand = [dec]

The delayed registration operation for the RF-proxy clients could not complete successfully.

ha-red-mode-client

LOG_STD_ACTION

RED_MODE-3-SELECT_MODE

3-Error

The mode change to [dec] was unsuccessful rc = [dec] force = [dec] caller = [dec]

The specified mode change operation did not complete successfully.

ha-red-mode-client

LOG_STD_ACTION

RED_MODE-4-PROC_CREATE

4-Warning

Red Mode process could not be created

The red mode process could not be created red mode changes may result in IPC hogs.

ha-red-mode-client

LOG_STD_ACTION

RED_MODE-3-CLIENT_REG

3-Error

Red Mode Client [dec] Registration failed [chars]

The Red Mode ISSU client could not be registered.

ha-red-mode-client

"show issu clients"

RED_MODE-3-ENTITY_REG

3-Error

Red Mode Entity [dec] Registration failed [chars]

The Red Mode ISSU entity could not be registered.

ha-red-mode-client

"show issu entities"

RED_MODE-3-MSGTYPE_REG

3-Error

Red Mode Msg Type for Entity [dec] Registration failed [chars]

The message type for the Red Mode ISSU could not be registered.

ha-red-mode-client

"show issu message types"

RED_MODE-3-MSGGROUP_REG

3-Error

Red Mode Msg Group [dec] for Entity [dec] Registration failed [chars]

The message group for the Red Mode ISSU could not be registered.

ha-red-mode-client

"show issu message groups"

RED_MODE-3-CAPTYPE_REG

3-Error

Red Mode Cap Type for Entity [dec] Registration failed [chars]

A capability type could not be registered for the Red Mode ISSU.

ha-red-mode-client

"show issu capability types"

RED_MODE-3-CAPENTRY_REG

3-Error

Red Mode Cap Entry [dec] for Entity [dec] Registration failed [chars]

A capability entry could not be registered for the Red Mode ISSU.

ha-red-mode-client

"show issu capability entries"

RED_MODE-3-CAPGROUP_REG

3-Error

Red Mode Cap Group [dec] for Entity [dec] Registration failed [chars]

A capability group could not be registered for the Red Mode ISSU.

ha-red-mode-client

"show capability groups"

RED_MODE-3-SESSION_REG

3-Error

Red Mode session for Entity [dec] Registration failed [chars]

The Red Mode ISSU session could not be registered.

ha-red-mode-client

"show issu sessions"

RED_MODE-3-SESSION_UNREG

3-Error

Red Mode session [dec] Un-Registration failed [chars]

The Red Mode ISSU session could not be unregistered.

ha-red-mode-client

"show issu sessions"

RED_MODE-3-CAP_REG

3-Error

Red Mode cap reg failed: reason [dec]

The capabilities of the Red Mode ISSU could not be registered.

ha-red-mode-client

"show issu capability <arguments>"

RED_MODE-3-MSG_REG

3-Error

Red Mode msg reg failed: reason [dec]

Messages for the Red Mode ISSU could not be registered.

ha-red-mode-client

"show issu message <arguments>"

RED_MODE-3-MSG_DATAPTR

3-Error

Red Mode Client [dec] get msg dataptr failed. Error = [dec]

The Red Mode ISSU client could not obtain a message data pointer.

ha-red-mode-client

"show issu fsm"

RED_MODE-3-MSG_MTU

3-Error

Red Mode Client [dec] get msg mtu failed. Error = [dec]

The Red Mode ISSU client could not obtain message size.

ha-red-mode-client

"show issu fsm"

RED_MODE-3-GET_BUFFER

3-Error

Red Mode ISSU session [dec] failed to get buffer

Red Mode ISSU failed to get a buffer

ha-red-mode-client

"show issu fsm"

RED_MODE-3-MSG_SEND

3-Error

Red Mode ISSU client for session [dec] failed to send message. Error Code = [chars]

The Red Mode ISSU client could not send a negotiation message to a peer.

ha-red-mode-client

"show issu fsm"

RED_MODE-3-CLIENT_REG_FAILED

3-Error

Red Mode ISSU client [dec] Client registration failed. [chars]

The Red Mode ISSU client could not be registered during system initialization.

ha-red-mode-client

"show issu clients"

RED_MODE-3-RED_MODE_MSG_NOT_OK

3-Error

Red Mode ISSU msg type [dec] is not ok

Red Mode ISSU message type has not negotiated correctly

ha-red-mode-client

"show message types <Client_ID>"

RED_MODE-3-RED_MODE_START_NEGO_FAILED

3-Error

Red Mode ISSU start nego session failed [chars]

The Red Mode ISSU could not start its negotiation process.

ha-red-mode-client

"show issu fsm"

RED_MODE-3-RED_MODE_XFROM_FAIL

3-Error

Red Mode ISSU [chars] transformation failed [chars]

The transformation operation for the Red Mode ISSU message has failed.

ha-red-mode-client

"show issu fsm and show issu sessions"

RED_MODE-3-IPC_AGENT

3-Error

[chars] [ [chars] ]

Failure in the Red Mode IPC agent

ha-red-mode-client

-

RED_MODE-3-ISSU_NEGOTIATION

3-Error

[chars] [ [chars] ]

Failure in the Red Mode Client

ha-red-mode-client

-

RED_MODE-3-ISSU_BASE_CLIENT_INCOMP

3-Error

One or more ISSU base clients are incompatible fallback to RPR

incompatible ISSU base client cause red_mode to fallback to RPR

-

"Check the console log for the name and ID of incompatible ISSU BASE " "clients"

RED_MODE-3-ISSU_SET_BASE_CLIENT_INCOMP

3-Error

Failed to set base client incompatibility

Failed to set base client incompatibility

-

"Check the console log for the name and ID of incompatible ISSU BASE " "clients"

RED_MODE-3-ISSU_RESET_PEER_IMAGE_COMP

3-Error

Failed to reset peer image to be compatible

Failed to reset peer image to be compatible after standby come back up to RPR

ha-red-mode-client

"This message is normally seen in conjunction with an ISSU module error " "message. Please examine the associated ISSU message for the reason for " "failure and action to take."

RED_MODE-4-NO_MODE_IN_CLI

4-Warning

Redundancy mode not defined in configuration. Please add to configuratio\n\n

The redundancy mode is usually defined at the top of the configuration. Until the redundancy mode is read or the end of the configuration is encountered the system will not allow the peer RSC to continue booting. Therefore if the system has to wait until the end of the configuration to discover that the default redundancy mode should be used then system booting times will be extended by the time taken for the RSC to read its configuration.

ha-red-mode-client

"Explicitly write the configuration to NVRAM so that the redundancy mode " "is discovered at an early stage."

RED_MODE-4-RPR_PLUS_DEPRECATION

4-Warning

\n *********************************************************\n * Warning The redundancy mode RPR+ is being deprecated *\n * and will be removed in future releases. Please change *\n * mode to SSO: *\n * redundancy *\n * mode sso *\n ********************************************************\n

RPR+ being deprecated

ha-red-mode-client

"Please change mode to SSO"

RED_MODE-3-INVALID_RF_DOMAIN

3-Error

Invalid RF domain [dec] [ [chars] ]

Invalid RF domain value

ha-red-mode-client

-

RF_ISSU-3-CLIENT_REG

3-Error

RF Client [dec] Registration failed

The RF ISSU client could not be registered.

ha-issu-infra

"show issu clients"

RF_ISSU-3-ENTITY_REG

3-Error

RF Entity [dec] domain [dec] Registration failed

The RF ISSU entity could not be registered.

ha-issu-infra

"show issu entities"

RF_ISSU-3-MSGTYPE_REG

3-Error

RF Msg Type for Entity [dec] domain [dec] Registration failed

The message type for the RF ISSU could not be registered.

ha-issu-infra

"show issu message types"

RF_ISSU-3-MSGGROUP_REG

3-Error

RF Msg Group [dec] for Entity [dec] domain [dec] Registration failed

The message group for the RF ISSU could not be registered.

ha-issu-infra

"show issu message groups"

RF_ISSU-3-CAPTYPE_REG

3-Error

RF Cap Type for Entity [dec] domain [dec] Registration failed

A capability type could not be registered for the RF ISSU.

ha-issu-infra

"show issu capability types"

RF_ISSU-3-CAPENTRY_REG

3-Error

RF Cap Entry [dec] for Entity [dec] domain [dec] Registration failed

A capability entry could not be registered for the RF ISSU.

ha-issu-infra

"show issu capability entries"

RF_ISSU-3-CAPGROUP_REG

3-Error

RF Cap Group [dec] for Entity [dec] domain [dec] Registration failed

A capability group could not be registered for the RF ISSU.

ha-issu-infra

"show capability groups"

RF_ISSU-3-SESSION_REG

3-Error

RF session for Entity [dec] domain [dec] Registration failed

The RF ISSU session could not be registered.

ha-issu-infra

"show issu sessions"

RF_ISSU-3-SESSION_UNREG

3-Error

RF session [dec] domain [dec] Un-Registration failed

The RF ISSU session could not be unregistered.

ha-issu-infra

"show issu sessions"

RF_ISSU-3-CAP_REG

3-Error

RF cap reg on domain [dec] failed: reason [dec]

The capabilities of the RF ISSU could not be registered.

ha-issu-infra

"show issu capability <arguments>"

RF_ISSU-3-MSG_REG

3-Error

RF msg reg on domain [dec] failed: reason [dec]

Messages for the RF ISSU could not be registered.

ha-issu-infra

"show issu message <arguments>"

RF_ISSU-3-MSG_DATAPTR

3-Error

RF Client [dec] domain [dec] get msg dataptr failed. Error = [dec]

The RF ISSU client could not obtain a message data pointer.

ha-issu-infra

"show issu fsm"

RF_ISSU-3-MSG_MTU

3-Error

RF Client [dec] domain [dec] get msg mtu failed. Error = [dec]

The RF ISSU client could not obtain message size.

ha-issu-infra

"show issu fsm"

RF_ISSU-3-GET_BUFFER

3-Error

RF ISSU session [dec] domain [dec] failed to get buffer

RF ISSU failed to get a buffer

ha-issu-infra

"show issu fsm"

RF_ISSU-3-MSG_SEND

3-Error

RF ISSU client for session [dec] domain [dec] failed to send message

The RF ISSU client could not send a negotiation message to a peer.

ha-issu-infra

"show issu fsm"

RF_ISSU-3-CLIENT_REG_FAILED

3-Error

RF ISSU client [dec] domain [dec] Client registration failed. [chars]

The RF ISSU client could not be registered during system initialization.

ha-issu-infra

"show issu clients"

RF_ISSU-3-RF_MSG_NOT_OK

3-Error

RF ISSU msg type [dec] for client [dec] on domain [dec] is not ok

RF ISSU message type has not negotiated correctly

ha-issu-infra

"show message types <Client_ID>"

RF_ISSU-3-RF_CAP_RESULT_INCOMP

3-Error

RF ISSU client capability exchange om domain [dec] result incompatible.

RF ISSU capabilities have negotiated incompatible

ha-issu-infra

"show issu negotiated capability <Session_ID>"

RF_ISSU-3-RF_CAP_INVALID_SIZE

3-Error

RF ISSU client capability list on domain [dec] is empty.

RF ISSU capability list size is invalid

ha-issu-infra

"show issu capability entires <Client_ID>"

RF_ISSU-3-INVALID_SESSION

3-Error

RF ISSU client on domain [dec] does not have a valid registered session.

The RF ISSU client does not have a valid registered session.

ha-issu-infra

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

RF_ISSU-3-ISSU_MSG_BAD_PEER_SID

3-Error

Inbound ISSU message routed through RF on domain [dec]

RF has received an invalid ISSU message which will not be processed.

redundancy-rf

"show redundancy history reverse"

RF_ISSU-3-CLIENT_REG

3-Error

RF Client [dec] Registration failed

The RF ISSU client could not be registered.

ha-issu-infra

"show issu clients"

RF_ISSU-3-ENTITY_REG

3-Error

RF Entity [dec] domain [dec] Registration failed

The RF ISSU entity could not be registered.

ha-issu-infra

"show issu entities"

RF_ISSU-3-MSGTYPE_REG

3-Error

RF Msg Type for Entity [dec] domain [dec] Registration failed

The message type for the RF ISSU could not be registered.

ha-issu-infra

"show issu message types"

RF_ISSU-3-MSGGROUP_REG

3-Error

RF Msg Group [dec] for Entity [dec] domain [dec] Registration failed

The message group for the RF ISSU could not be registered.

ha-issu-infra

"show issu message groups"

RF_ISSU-3-CAPTYPE_REG

3-Error

RF Cap Type for Entity [dec] domain [dec] Registration failed

A capability type could not be registered for the RF ISSU.

ha-issu-infra

"show issu capability types"

RF_ISSU-3-CAPENTRY_REG

3-Error

RF Cap Entry [dec] for Entity [dec] domain [dec] Registration failed

A capability entry could not be registered for the RF ISSU.

ha-issu-infra

"show issu capability entries"

RF_ISSU-3-CAPGROUP_REG

3-Error

RF Cap Group [dec] for Entity [dec] domain [dec] Registration failed

A capability group could not be registered for the RF ISSU.

ha-issu-infra

"show capability groups"

RF_ISSU-3-SESSION_REG

3-Error

RF session for Entity [dec] domain [dec] Registration failed

The RF ISSU session could not be registered.

ha-issu-infra

"show issu sessions"

RF_ISSU-3-SESSION_UNREG

3-Error

RF session [dec] domain [dec] Un-Registration failed

The RF ISSU session could not be unregistered.

ha-issu-infra

"show issu sessions"

RF_ISSU-3-CAP_REG

3-Error

RF cap reg on domain [dec] failed: reason [dec]

The capabilities of the RF ISSU could not be registered.

ha-issu-infra

"show issu capability <arguments>"

RF_ISSU-3-MSG_REG

3-Error

RF msg reg on domain [dec] failed: reason [dec]

Messages for the RF ISSU could not be registered.

ha-issu-infra

"show issu message <arguments>"

RF_ISSU-3-MSG_DATAPTR

3-Error

RF Client [dec] domain [dec] get msg dataptr failed. Error = [dec]

The RF ISSU client could not obtain a message data pointer.

ha-issu-infra

"show issu fsm"

RF_ISSU-3-MSG_MTU

3-Error

RF Client [dec] domain [dec] get msg mtu failed. Error = [dec]

The RF ISSU client could not obtain message size.

ha-issu-infra

"show issu fsm"

RF_ISSU-3-GET_BUFFER

3-Error

RF ISSU session [dec] domain [dec] failed to get buffer

RF ISSU failed to get a buffer

ha-issu-infra

"show issu fsm"

RF_ISSU-3-MSG_SEND

3-Error

RF ISSU client for session [dec] domain [dec] failed to send message

The RF ISSU client could not send a negotiation message to a peer.

ha-issu-infra

"show issu fsm"

RF_ISSU-3-CLIENT_REG_FAILED

3-Error

RF ISSU client [dec] domain [dec] Client registration failed. [chars]

The RF ISSU client could not be registered during system initialization.

ha-issu-infra

"show issu clients"

RF_ISSU-3-RF_MSG_NOT_OK

3-Error

RF ISSU msg type [dec] for client [dec] on domain [dec] is not ok

RF ISSU message type has not negotiated correctly

ha-issu-infra

"show message types <Client_ID>"

RF_ISSU-3-RF_CAP_RESULT_INCOMP

3-Error

RF ISSU client capability exchange on domain [dec] result incompatible.

RF ISSU capabilities have negotiated incompatible

ha-issu-infra

"show issu negotiated capability <Session_ID>"

RF_ISSU-3-RF_CAP_INVALID_SIZE

3-Error

RF ISSU client capability list on domain [dec] is empty.

RF ISSU capability list size is invalid

ha-issu-infra

"show issu capability entires <Client_ID>"

RF_ISSU-3-INVALID_SESSION

3-Error

RF ISSU client on domain [dec] does not have a valid registered session.

The RF ISSU client does not have a valid registered session.

ha-issu-infra

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

RF_ISSU-3-ISSU_MSG_BAD_PEER_SID

3-Error

Inbound ISSU message routed through RF on domain [dec]

RF has received an invalid ISSU message which will not be processed.

redundancy-rf

"show redundancy history reverse"

VRRS-3-ERROR

3-Error

Internal error [chars]

An internal software error occurred.

fhrp: vrrs

LOG_STD_ACTION

VRRS-4-WARN

4-Warning

Internal warning [chars]

An internal software warning occurred.

fhrp: vrrs

LOG_STD_ACTION

VRRS-6-STATE

6-Information

[chars]

The VRRS router has changed state.

-

LOG_STD_NO_ACTION

VRRS-6-INFO

6-Information

Internal info [chars]

An internal software information message occurred.

fhrp: vrrs

LOG_STD_ACTION

MACDB-3-ERROR

3-Error

Internal error [chars]

An internal software error occurred.

fhrp: macdb

LOG_STD_ACTION

MACDB-4-WARN

4-Warning

Internal warning [chars]

An internal software warning occurred.

fhrp: macdb

LOG_STD_ACTION

MACDB-6-INFO

6-Information

Internal info [chars]

An internal software information message occurred.

fhrp: macdb

LOG_STD_ACTION

FHRP-3-ERROR

3-Error

Internal error [chars]

An internal software error occurred.

fhrp

LOG_STD_ACTION

FHRP-4-WARN

4-Warning

Internal warning [chars]

An internal software warning occurred.

fhrp

LOG_STD_ACTION

FHRP-6-INFO

6-Information

Internal info [chars]

An internal software information message occurred.

fhrp

LOG_STD_ACTION

VRRP-3-ERROR

3-Error

Internal error [chars]

An internal software error occurred.

fhrp: vrrp

LOG_STD_ACTION

VRRP-4-WARN

4-Warning

Internal warning [chars]

An internal software warning occurred.

fhrp: vrrp

LOG_STD_ACTION

VRRP-4-CFG_WARN

4-Warning

[chars]

-

-

LOG_STD_NO_ACTION

VRRP-6-STATE

6-Information

[chars]

The VRRP router has changed state.

-

LOG_STD_NO_ACTION

VRRP-6-INFO

6-Information

Internal info [chars]

An internal software information message occurred.

fhrp: vrrp

LOG_STD_ACTION

VRRP_LOG_ERROR-3-VRRPV3_LOG

3-Error

ERRMSG_NOFLAGS

-

-

-

VRRP_LOG_WARN-4-VRRPV3_LOG

4-Warning

ERRMSG_NOFLAGS

-

-

-

VRRP_LOG_CFG_WARN-4-VRRPV3_LOG

4-Warning

ERRMSG_NOFLAGS

-

-

-

VRRP_LOG_STATE-5-VRRPV3_LOG

5-Notice

ERRMSG_NOFLAGS

-

-

-

VRRP_LOG_INFO-6-VRRPV3_LOG

6-Information

ERRMSG_NOFLAGS

-

-

-

FHRP_LOG_ERROR-3-FHRP_LOG

3-Error

ERRMSG_NOFLAGS

-

-

-

FHRP_LOG_WARN-4-FHRP_LOG

4-Warning

ERRMSG_NOFLAGS

-

-

-

FHRP_LOG_INFO-6-FHRP_LOG

6-Information

ERRMSG_NOFLAGS

-

-

-

VRRS_LOG_ERROR-3-VRRS_LOG

3-Error

ERRMSG_NOFLAGS

-

-

-

VRRS_LOG_WARN-4-VRRS_LOG

4-Warning

ERRMSG_NOFLAGS

-

-

-

VRRS_LOG_STATE-5-VRRS_LOG

5-Notice

ERRMSG_NOFLAGS

-

-

-

VRRS_LOG_INFO-6-VRRS_LOG

6-Information

ERRMSG_NOFLAGS

-

-

-

TRACK-3-ERROR

3-Error

Internal error [chars]

An internal software error occurred.

fhrp: track

LOG_STD_ACTION

TRACK-4-WARN

4-Warning

Internal warning [chars]

An internal software warning occurred.

fhrp: track

LOG_STD_ACTION

TRACK-6-STATE

6-Information

[chars]

The Tracked object has changed state.

fhrp: track

LOG_STD_NO_ACTION

TRACK-6-INFO

6-Information

Internal info [chars]

An internal software information message occurred.

fhrp: track

LOG_STD_ACTION

LCRED-3-EREVENT1

3-Error

[chars] 0x[hec]

This message is used for reporting invalid values for parameters or database members.

ha-lcred-infra

"Check the redundancy configuration for the " "slot with 'show redundancy linecard all' and 'show " "redundancy linecard group all'. Fix the configuration " "if required and re-execute the command making sure " "any command parameters are correct. If it's still in " "error then file a case with TAC. In addition to the " "usual system information provide them with the output " "from above commands and 'show redundancy linecard " "history'."

LCRED-3-VIFTWICE

3-Error

LC: Request to add a second virtual interface to group [dec].

An attempt was made to add a virtual interface to a redundant interface group which already has a configured virtual interface.

ha-lcred-infra

"If this error was in response to a user " "command then check the command and try again if it " "appears correct. If the error seems to be from some " "undefined action then file a TAC case and attach the " "output from 'show redundancy linecard group all' and " "'show redundancy linecard history'."

LCRED-3-MEMBERTWICE

3-Error

LC: Request to add slot member [dec] twice to group [dec].

An attempt was made to add a member from the specified slot to a redundant interface group which already contains a member from that slot.

ha-lcred-infra

"This is a user error. Please double-check " "the configuration with 'show redundancy linecard group " "all' and try the command again."

LCRED-3-UPDATENOTSENT

3-Error

The update message was not sent to the linecards

-

-

-

LCRED-3-INVALID_DEBUG

3-Error

Invalid debug type parameter [dec] specified.

The function responsible for turning debugging on/off was called with an invalid debug type code.

ha-lcred-infra

"Verify the debug command is available " "by 'debug redundancy lc ?' and try it again."

LCRED-3-UNMAPPED_IFINDEX

3-Error

NULL/Invalid [chars] ifindex 0x[hec] downloaded for interface group number [dec].

The interface identifier specified for a member or virtual interface of a redundant interface group does not correspond to a known interface.

ha-lcred-infra

"Open a TAC case. Attach the output of " "'show redundancy linecard all' 'show redundancy " "linecard group all' and 'show redundancy linecard " "history'."

LCRED-3-NO_SLOT_TO_DELETE

3-Error

LC: Request to delete non-member slot [dec] from redundancy group [dec].

An attempt was made to delete a slot from a redundant line card group which does not contain the specified slot as a member.

ha-lcred-infra

"Check the configuration with 'show " "redundancy linecard group all' and try command again."

LCRED-3-NOIPCMEM

3-Error

Cannot Allocate IPC memory to get message.

Can't allocate memory to send redundancy control message.

ha-lcred-infra

"This is indicative of system memory " "shortage. The problem is likely unrelated to linecard " "redundancy. You should initiate recovery procedures as " "you would for any system that does not have sufficient " "memory to perform actions."

LCRED-3-IPCPORT

3-Error

Can't Create IPC port [chars] error [chars] IPC err[chars].

Can't create IPC to receive traffic from peer.

ha-lcred-infra

"Check redundancy configuration with " "'show redundancy linecard all'. If the configuration is not " "what you expected try the commands again. If the configuration " "is correct and you get this message try switching over the " "linecard if the standby LC is configured and ready. Otherwise " "try resetting the linecard in the slot specified. If you still " "get the error submit a TAC case with the system information " "'show redundancy linecard all' and 'show proc mem'."

LCRED-3-IPC

3-Error

\n[chars]

General IPC error.

ha-lcred-infra

"Check redundancy configuration with " "'show redundancy linecard all'. If the configuration is not " "what you expected try the commands again. If the configuration " "is correct and you get this message try switching over the " "linecard if the standby LC is configured and ready. Otherwise " "try resetting the linecard in the slot specified. If you still " "get the error submit a TAC case with the system information " "'show redundancy linecard all' and 'show proc mem'."

LCRED-3-NOINITMEM

3-Error

Subsystem Init [chars] Failed due to unavailability of memory of

Initialization of LCRED subsystem failed due to insufficient memory.

ha-lcred-infra

"This is indicative of system memory " "shortage. The problem is likely unrelated to linecard " "redundancy. You should initiate recovery procedures as " "you would for any system that does not have sufficient " "memory to perform actions."

LCRED-3-LC_STATE_PROG_FAILED

3-Error

Redundant Line Card [chars] idx=[dec] state progression failure. Line

Redundant Line Card state progression failure.

ha-lcred-infra

"This is informational. The LCRED system " "will reset the linecard to recover. No action is required " "unless the error keeps re-occurring. If it keeps happening " "then open a TAC case. Include 'show redundancy linecard all' " "'show redundancy linecard group all' and 'show redundancy " "linecard history'."

LCRED-3-LC_STATE_PROG_ERROR

3-Error

Illegal event in redundant Line Card [chars] idx=[dec] state progression.

Illegal event in redundant Line Card state progression.

ha-lcred-infra

"This is informational. The LCRED system " "will reset the linecard to recover. No action is required " "unless the error keeps re-occurring. If it keeps happening " "then open a TAC case. Include 'show redundancy linecard all' " "'show redundancy linecard group all' and 'show redundancy " "linecard history'."

LCRED-3-CANT_SET_ROLE

3-Error

Couldn't set or clear slot or port roles for Line card [chars] idx=[dec].

Failed when attempting to set or clear the slot or port Active/Standby roles for a Line Card .

ha-lcred-infra

"This indicates an error during redundant " "linecard state progression. User should check redundancy config " "and try to remedy via CLI if not correct. Check config by " "'show redundancy linecard all' and 'show redundancy linecard " "group all'. If redundancy config cannot be corrected then " "open a TAC case attaching the info above and also 'show " "redundancy linecard history' 'show version' and 'show run'."

LCRED-3-LC_PROG_TO_INIT_ERROR

3-Error

Unable to reset progression to INIT for Line Card [chars] idx=[dec].

Attempt to reinitialize progression failed.

ha-lcred-infra

"This indicates an error during redundant " "linecard state progression. User should check redundancy config " "and try to remedy via CLI if not correct. Check config by " "'show redundancy linecard all' and 'show redundancy linecard " "group all'. If redundancy config cannot be corrected then " "open a TAC case attaching the info above and also 'show " "redundancy linecard history' 'show version' and 'show run'."

LCRED-3-LC_STATE_PROG_HARD_FAILURE

3-Error

Redundant Line Card [chars] idx=[dec] state progression failed more than [dec]

Redundant Line Card state progression failure rate exceeds threshold.

ha-lcred-infra

"Open a TAC case attaching the following: " "'show redundancy linecard all' 'show redundancy linecard group " "all' 'show redundancy linecard history' 'show version' and " "'show run'."

LCRED-2-SYNC_FAILURE_NO_BUFFER

2-Critical

Could not get sync buffer to checkpoint data.

An attempt to get a sync buffer failed when trying to sync data from Active RP to Standby. This is likely a system memory issue. The platform code has been notified to take possible corrective action.

ha-lcred-infra

"Informational. The system will correct " "if possible."

LCRED-3-SYNC_FAILURE_ISSU_NOT_OK

3-Error

Could not send checkpoint message during [chars] sync because issu infrastructure deemed ISSU state is incorrect.

The ISSU infrastructure deemed the ISSU state of Linecard Redundancy's ISSU client peer is incorrect.

ha-lcred-infra

"If this message occurs once ISSU client " "negotiation is complete and system is up and running " "you need to reset the Standby RP. If it occurs during " "system bringup nothing needs to be done. The HA " "infrastructure should recover without intervention."

LCRED-2-SEND_SYNC_MESSAGE_FAILED

2-Critical

Checkpointing sync message to client on Standby RP was not received.

A sync message was sent from the Active RP but it was never received or was received in corrupted form on the Standby RP. The platform code has been notified and platform-specific recovery actions will be taken.

ha-lcred-infra

"Informational. The linecard recovery " "infrastructure will take recovery actions."

LCRED-2-RECEIVE_SYNC_MESSAGE_FAILED

2-Critical

Checkpointing sync message was received on Standby RP but it was corrupted or there was an error processing it.

A sync message was sent from the Active RP and received on the Standby RP. The message was either empty corrupted or could not be processed by Standby client. If system is NOT in bulk sync mode then Standby RP will be reset.

ha-lcred-infra

"Informational. The linecard recovery " "infrastructure will take recovery actions."

LCRED-3-HWIDB_SUBBLOCK_CREATE_FAIL

3-Error

Creation of hwidb subblock for [chars] i/f [chars] failed.

Each redundant i/f whether active standby or virtual has a hwidb subblock that stores redundancy information about that i/f. If this subblock cannot be created then creation of the redundant i/f will fail.

ha-lcred-infra

"Try the CLI that triggered it again. If the " "error occurs again open a case with TAC. Report the output of " "'show redundancy linecard group all' and 'show redundancy " "linecard all' in addition to usual system configuration " "information."

LCRED-3-NO_HWIDB_RED_SUBBLOCK

3-Error

No redundancy subblock is found for i/f [chars].

Each redundant i/f whether active standby or virtual has a hwidb subblock that stores redundancy information about that i/f. If this subblock cannot be found then an error is reported.

ha-lcred-infra

"Try the CLI that triggered it again. If the " "error occurs again open a case with TAC. Report the output of " "'show redundancy linecard group all' 'show redundancy " "linecard all' and 'show redundancy linecard sub-block all' " "in addition to usual system configuration information."

LCRED-3-NO_MORE_PREALLOCATED_SUBBLOCK_MEMORY

3-Error

Could not allocate redundancy subblock. Pre-allocated memory for subblock creation of [dec] is exhausted.

The platform pre-allocates a pool of memory for creating redundancy subblocks via registry plfm_get_max_redundancy_sb. This pool has been

ha-lcred-infra

"Open a case with TAC. Report the contents " "of this message including the preallocation size value. " "Provide TAC with the following information: 'show run' " "'show ver' 'show hardware' and 'show proc mem'. TAC " "will need to get the platform in question to increase " "the pre-allocated pool of memory."

LCRED-2-SUBSYSTEM_INIT_FAILED

2-Critical

Subsystem failed during init phase with error [chars].

During subsystem initialization for LCRED Line Card Redundancy subsystem an unrecoverable error occurred. The system will come up and run fine but linecard redundancy will not be available for configuration and will not come up if it was already configured in start-config.

ha-lcred-infra

"You can continue to use the system without " "linecard redundancy. At your earliest convenience reloading the " "system might allow linecard redundancy subsystem to come up. In " "any case report the error message to TAC and include the " "following: 'show run' 'show redundancy linecard history' " "'show redundancy linecard all' and 'show version'."

LCRED-3-VIF_HWIDB_CREATE_FAIL

3-Error

Virtual hwidb creation failed from physical i/f [chars]: [chars].

Creation of virtual hwidb failed with specified error.

ha-lcred-infra

"Without the virtual hwidb VIF the i/f "

LCRED-3-REMOVE_SLOT_OR_IF_FAILURE

3-Error

Removal of redundant interface caused an unexpected condition for i/f [chars].

While removing a redundant i/f possibly during redundant LC removal a SW bug was encountered. LC redundancy

ha-lcred-infra

"Verify LC Redundancy config with 'show " "redundancy linecard all' and 'show redundancy linecard group " "all'. Try to fix config with CLI. Open TAC case with above " "output as well as 'show run' 'show ver' and 'show redundancy " "history'."

LCRED-3-COULDNT_ADD_REDUNDANT_IF

3-Error

Error occurred while configuring redundant interface [dec]/[dec]: [chars]

While configuring a redundant i/f the specified error occurred. This means the redundant configuration command was NOT successfully completed.

ha-lcred-infra

"First verify the command was correct and " "verify the current redundancy config with 'show redundancy " "linecard all' and 'show redundancy linecard group all'. If you " "feel the command was correct and failed anyway file a TAC " "case with the following: 'show run' 'show redundancy linecard " "history' 'show redundancy linecard all' 'show proc mem' and " "'show version'."

LCRED-4-PARTIAL_CONFIG_LOSS

4-Warning

Partial redundancy config loss while configuring redundant interface [dec]/[dec]

During system reload could not get hwidb for the Secondary i/f so the Secondary redundancy configuration will be lost. The Primary i/f will be Active if it was parsed correctly.

ha-lcred-infra

"Verify that Primary i/f is configured. " "Reconfigure Secondary i/f for redundancy."

LCRED-3-LC_UP_WITH_ILLEGAL_ROLE

3-Error

Illegal Line Card redundancy role assignments during linecard up.

When LC comes up illegal Line Card redundancy role was assigned to it and/or its peer. There are four kinds of roles can be assigned to a LC: Active Standby Wait or None. The only legal combination of roles for a slot and its peer are: Active-NONE Active-Standby WAIT-NONE. The rest are all illegal.

ha-lcred-infra

"Informational only. The system will reset " "both linecards in the redundant pair to recover."

LCRED-3-LC_ROLE_NEG_DONE_WITH_ILLEGAL_ROLE

3-Error

Illegal Line Card redundancy role assignments found following role negotiation.

When LC role negotiation is done illegal Line Card redundancy role was assigned to it and/or its peer. There are four kinds of roles can be assigned to a LC: Active Standby Wait or None. The only legal combination of roles for a slot and its peer are: Active-NONE Active-Standby WAIT-NONE. The rest are all illegal.

ha-lcred-infra

"Informational only. The LC Redundancy system " "will take recovery action."

LCRED-3-LC_PROG_RETURNED_ERROR

3-Error

Progression attempt returned error for Line Card [chars] idx=[dec].

Attempt to complete progression failed.

ha-lcred-infra

"This indicates an error during redundant " "linecard state progression. User should check redundancy " "config and try to remedy via CLI if not correct. Check " "config by 'show redundancy linecard all' and 'show " "redundancy linecard group all'. If redundancy config cannot " "be corrected then open a TAC case attaching the info above " "and also 'show redundancy linecard history' 'show version' " "and 'show run'."

LCRED-3-LC_CANT_SET_TXRX

3-Error

Unable to set Active/Standby Tx/Rx selection for Line Card [chars] idx=[dec].

Platform driver rejected a request to set the Tx/Rx selectors for a redundant linecard.

ha-lcred-infra

"This indicates the platform was unable to " "initialize linecard Active/STandby states. User should check " "redundancy config and try to remedy via CLI if not correct. " "Check config by 'show redundancy linecard all' and 'show " "redundancy linecard group all'. If redundancy config cannot " "be corrected then open a TAC case attaching the info above " "and also 'show redundancy linecard history' 'show version' " "and 'show run'."

LCRED-3-LC_CARD_MISMATCH

3-Error

Mismatch is seen between Inserted card type0x%X [dec] and

Inserted card type is rejected by lcred component due to mismatch between inserted card type and reserved card type

ha-lcred-infra

"This indicates the reserved card type is " "different than inserted card type. Check the reserve-cardtype setting " "in show run. Insert the card type same of reserve card type " "If the cards are of same type but still it shows mismatch then open " "a TAC case attaching output of 'show run' " "'redundancy linecard group all' 'redundancy lincard group <group#>.'"

LCRED-4-LC_PLFM_SUPPRESS_SWITCHOVER

4-Warning

Platform has requested to temporarily suppress switchover for Line card redundancy group Group Index=[dec].

Attempt to switchover is suppress. This is just the informative message and not the error

ha-lcred-infra

"This indicates an informative error message " "during switchover.If secondary is never becoming Active for the " "failed or removed primary after Chassis reload then open a TAC " "case."

CCM-3-CCMREGFAIL

3-Error

High Availability Registration failed

Cluster Control Manager High Availability features will not work.

ccm

LOG_STD_ACTION

CCM-3-CCMNOCLIENT

3-Error

Client [chars][[dec]] not present

Cluster Control Manager High Availability features for this client will not work.

ccm

"Refer to the documentation on configuring High Availability features"

CCM-3-CCMINVALEVT

3-Error

Client[[dec]] received an invalid event[[dec]]

Cluster Control Manager High Availability feature on standby detected an invalid event received from active

ccm

LOG_STD_ACTION

NTI-3-AGENT_ERR

3-Error

[chars] Notifying platform about AGENT ERROR [chars] AGENT EP ID 0x[hec] for EP ID 0x[hec] EP type [chars] EP group [chars]

An NTI AGENT error has occured

nti

LOG_STD_ACTION

NTI-3-TRIG_PROCESSING

3-Error

[chars] Trigger processing ERROR for client #[dec] - [chars] EP ID 0x[hec] trigger

An NTI Trigger Processing Error has occured

nti

LOG_STD_ACTION

NTI-3-TRIG_ABORT_ALL_CLIENTS

3-Error

[chars] Aborting trigger processing for all clients as requested by the platform EP ID 0x[hec] trigger type [chars] trigger group [chars]

Trigger processing has been aborted for all clients due to a platform request

nti

LOG_STD_ACTION

NTI-3-TRIG_CLIENT_NOTINLIST

3-Error

[chars] Cannot trigger NTI client [dec] for this EP: could not find client

Could not Trigger NTI Client for an EP as it is not in the list

nti

LOG_STD_ACTION

NTI-3-CLIENT_NOT_REGSTRD_FOR_EPTYPE

3-Error

[chars] Client #[dec] - [chars] has NOT registered for platform EP type [chars]

A Client has not registered for a platform EP type

nti

LOG_STD_ACTION

NTI-3-ISSU_INVALID_SESSION

3-Error

Invalid session for ep 0x[hec]

NTI ISSU session is invalid for endpoint. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_EXISTING_SESSION

3-Error

Session already exists for ep 0x[hec]

NTI ISSU session already exists for endpoint. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_INVALID_MEDMAN

3-Error

Invalid MEDMan data

MEDMan Multiple Endpoint Data Manager data is invalid. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_NOT_INIT

3-Error

NTI ISSU is not initialized endpoint 0x[hec].

NTI ISSU is not initialized. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_NEGO_ALREADY_STARTED

3-Error

NTI ISSU negotiation already started endpoint 0x[hec]

Tried to start the NTI ISSU negotiation but it started already. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_DUMMY_MSG_FAILED

3-Error

Failed to send a dummy nego msg to endpoint 0x[hec]

NTI ISSU failed to send a dummy negotiation message to trigger negotiation on the peer. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_NEGO_ASYNC_ERROR

3-Error

Async error during nego with 0x[hec] [chars]

NTI ISSU got an asynchronous error during negotiation with an endpoint. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_MEDMAN_CREATE

3-Error

Failed to create MEDMan data for endpoint 0x[hec]

NTI ISSU failed to create MEDMan data for an endpoint. Negotiation can't be done the endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_MEDMAN_GET

3-Error

Failed to get MEDMan data for endpoint 0x[hec] [chars]

NTI ISSU failed to retreive MEDMan data for an endpoint. ISSU negotiation will failed with this endpoint and it will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_AGENT_LIST_ALLOC

3-Error

Failed to allocate agent bitlist for endpoint 0x[hec]

NTI ISSU failed to allocate the agents bitlist for an endpoint. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_INVALID_RC

3-Error

Invalid ISSU rc argument for endpoint 0x[hec]

NTI ISSU got an invalid ISSU return code argument. ISSU negotiation will fail the endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_NEGO_INCOMPATIBLE

3-Error

Negotiation incompatible for endpoint 0x[hec]

NTI ISSU was incompatible for this endpoint. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_UNKNOWN_MSG_TYPE

3-Error

NTI ISSU got an unknown message type: [dec]

NTI ISSU got an unknown message type when trying to get the message MTU. The message can't be sent.

nti

LOG_STD_ACTION

NTI-3-ISSU_MTU_FAILED

3-Error

NTI ISSU failed to get MTU for message type [dec] [chars]

NTI ISSU failed to get the message MTU for transformation. The message can't be sent.

nti

LOG_STD_ACTION

NTI-3-ISSU_XMIT_FAILED

3-Error

NTI ISSU failed to transform message type [dec] for transmit to 0x[hec] [chars]

NTI ISSU failed to transform the message for transmit. The message can't be sent.

nti

LOG_STD_ACTION

NTI-3-ISSU_RCV_FAILED

3-Error

NTI ISSU failed to transform message type [dec] for receive from 0x[hec] [chars]

NTI ISSU failed to transform the message for receive. The message can't be processed.

nti

LOG_STD_ACTION

NTI-3-ISSU_INVALID_RCVD_MSG

3-Error

NTI ISSU received an invalid message for transformation from endpoint 0x[hec]

NTI ISSU received an invalid message for transformation. The message can't be processed.

nti

LOG_STD_ACTION

NTI-3-ISSU_RCVD_NEGO_NOT_DONE

3-Error

NTI ISSU negotiation not done when received a message from 0x[hec]

NTI ISSU not done when received a message. The message can't be processed.

nti

LOG_STD_ACTION

NTI-3-ISSU_RCVD_UNKNOWN_MSG

3-Error

NTI ISSU received an unknown message type [dec] from 0x[hec]

NTI ISSU received a message whose type is unknown. The message can't be processed.

nti

LOG_STD_ACTION

NTI-3-ISSU_RCVD_TRANS_FAILED

3-Error

NTI ISSU failed to transform received message from 0x[hec]

NTI ISSU failed to transform a received message. The message can't be processed.

nti

LOG_STD_ACTION

NTI-3-ISSU_TRIG_NEGO_NOT_DONE

3-Error

NTI ISSU negotiation not done when getting a trigger from 0x[hec]

NTI ISSU negotiation should have been done when getting a trigger from this endpoint. The trigger will be ignored

nti

LOG_STD_ACTION

NTI-3-ISSU_INVALID_MSG_TRANS

3-Error

NTI ISSU transformation function got an invalid message in argument

NTI ISSU transformation function got an invalid message in argument. The message can't be transformed and won't be processed.

nti

LOG_STD_ACTION

NTI-3-ISSU_PLATFORM_TRANSPORT_NEGO_SEND

3-Error

NTI ISSU failed to send an platform transport nego message to 0x[hec]

NTI ISSU failed to send a negotiation message using the platform transport. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_PLATFORM_TRANSPORT_NEGO_GET_REQ_PAK

3-Error

NTI ISSU failed to get an platform transport nego message

NTI ISSU failed to get an platform transort nego message. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_REG_RECEIVE_NEGO_MSG

3-Error

NTI ISSU failed call the platform receive nego message registry

NTI ISSU failed to NTI ISSU failed call the platform receive nego message registry. The endpoint will most likely be reset.

nti

LOG_STD_ACTION

NTI-3-ISSU_REG_ADD

3-Error

NTI ISSU failed to hook to the registry [chars]

NTI ISSU failed to hook to a registry. This endpoint will most likely be reset.

nti

LOG_STD_ACTION

IPV6_RIP-3-NULLIDB

3-Error

Uninitialized interface pointer - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-NULLPAK

3-Error

Uninitialized packet pointer - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-NULLPDB

3-Error

Uninitialized PDB pointer - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-NULLIPDB

3-Error

Uninitialized iPDB pointer - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-NULLPROTO

3-Error

Uninitialized protocol pointer - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-NULLSOC

3-Error

Uninitialized socket pointer - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-ALLOC_PDB

3-Error

Can't alloc PDB structure - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-ALLOC_IPDB

3-Error

Can't alloc iPDB structure - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-PROCESS_CREATE

3-Error

Can't create process - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-ALLOC_ERR

3-Error

Memory allocation problem - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_RIP-3-PROCESS_MSG_SEND

3-Error

Can't send message to process - RIPv6

An internal software error occurred.

ipv6

LOG_STD_ACTION

XDR-3- XDRIPC

3-Error

XDR IPC error on multicast-group 0x[hec] due to [chars].

A general IPC related error occurred which may prevent transfer of data to other peers using the IPC mechanism

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" immediately after this error. " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-6- XDRIPCPEER

6-Information

XDR IPC error occurred for peer in slot [chars] due to [chars][chars].

A general IPC related error occurred which may prevent transfer of data to other peers using the IPC mechanism

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" and \"show xdr linecard\" " "immediately after this error. Copy the message exactly as it appears " "and report it to your technical support representative."

XDR-2- XDRDISABLEREQUEST

2-Critical

Peer in slot [chars] requested to be disabled due to: [chars]. Disabling linecard

Due to some error condition the linecard has requested to be disabled

XDR_DDTS_COMPONENT

"Execute \"clear xdr linecard\" from the RP followed by " "\"clear xdr channel\" on the linecard in question to clear the " "error condition. If the problem persists get the output of " "\"show monitor event-trace xdr all\" from the RP and the linecard in " "question and report it to your technical support representative."

XDR-2- XDRLCDISABLEREQUEST

2-Critical

Client [chars] requested to be disabled. [chars]

Due to some error condition the linecard has requested to be disabled

XDR_DDTS_COMPONENT

"Execute \"clear xdr linecard\" from the RP followed by " "\"clear xdr channel\" on the linecard in question to clear the " "error condition. If the problem persists get the output of " "\"show monitor event-trace xdr all\" from the RP and the linecard in " "question and report it to your technical support representative."

XDR-3- XDRNOMEM

3-Error

XDR failed to allocate memory during [chars] creation.

Allocation of memory by the XDR subsystem failed. This may result in an unpredictable behavior of XDR

XDR_DDTS_COMPONENT

"Make sure that there is enough memory for the operations being performed " "by your machine. " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- PULLSENDFAIL

3-Error

Sending data for pull client [chars] to [chars] failed due to slots [chars] not being in group 0x[hec] of slots [chars]

-

-

-

XDR-3- NONINCRSEQ

3-Error

Non-increasing maximum sequence [dec] was [dec] received from slot [chars]

-

-

-

XDR-3- BADSEQVAL

3-Error

Incorrect maximum sequence calculated [dec] was [dec] for slot [chars]

Internal software error. May result in unpredictable behaviour.

XDR_DDTS_COMPONENT

"show xdr linecard"

XDR-6- ISSUBADRCVTFM

6-Information

Failed to rcv_transform message - slot [chars] reason: [chars]

Unable to perform ISSU transform on incoming XDR header. Message will be ignored

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-6- ISSUBADTXTFM

6-Information

Failed to xmit_transform message - slot [chars] reason [chars]

Unable to perform ISSU transform on outgoing XDR header. Message will be ignored

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- ISSUBADREGPARAMS

3-Error

XDR client [chars] trying to register with incomplete ISSU support.

This client does not properly support ISSU and will be registered as not supporting ISSU.

XDR_DDTS_COMPONENT

"We cannot allow a client to register with partial ISSU support so it will " "be registered without it. Please report this message to your technical " "support representative."

XDR-3- ISSUCAPNEGOFAIL

3-Error

XDR client [chars] failed to [chars] capability/ies due to [chars]

Internal software error - capability negotiation failed unexpectedly.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative"

XDR-3- ISSUINITFAIL

3-Error

Unable to register XDR ISSU [chars] reason: [chars]

Unable to register the given XDR ISSU parameter due to the reason given. This will stop ISSU working for this client and may lead to unpredictable behaviour.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-6- ISSUCLIENTABSENT

6-Information

XDR client [chars] absent on slot [chars]. Client functionality may be affected.

The remote slot doesn't support this ISSU client. The software will handle this by reducing client functionality locally to continue in SSO mode or by forcing the remote peer into RPR mode as apprporiate. This is expected behaviour in ISSU-capable systems.

XDR_DDTS_COMPONENT

"No action required. This message just indicates that certain " "functionality may be reduced due to running different images together."

XDR-3- ISSU_ENUM_ERROR

3-Error

Enum for [chars] [chars] component is not ISSU-compliant: [chars]

The given enumeration is not ISSU-compliant for the reason given. Unpredictable behaviour will result when interoperating with different IOS versions.

XDR_DDTS_COMPONENT

"This requires a code fix before the image can be shipped or ISSU will be " "broken."

XDR-3- CLIENTISSUBADGROUP

3-Error

New m/cast group slots [chars] has multiple members before nego complete.

-

-

-

XDR-3- CLIENTISSUBADNEGOMSG

3-Error

Unexpected nego msg - slot [chars] XDR client [chars] ctxt [dec]

XDR has received a negotiation message unexpectedly as this client is either not ISSU aware or has already completed negotiation for this slot. This is likely a precursor to unpredictable behaviour for this client.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSUSENDFAILED

3-Error

Can't send XDR client ISSU nego msg: reason [chars] slot [chars] XDR client [chars]

XDR has failed to send an ISSU negotiation message for the given client. The slot will be marked as ISSU-unaware and communication with this slot will proceed on that basis. However this is likley to lead to unpredictable behaviour.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Also copy the message exactly as it appears and report it to your " "technical support representative."

XDR-3- CLIENTISSUSTARTNEGOFAIL

3-Error

Can't start nego: reason [chars] slot [chars] XDR client [chars] sid [dec]

XDR has failed to start ISSU negotiation with the remote slot for the reason given. The slot will be marked as ISSU-unaware and communication with this slot will proceed on that basis. However this is likley to lead to unpredictable behaviour.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Also copy the message exactly as it appears and report it to your " "technical support representative."

XDR-6- CLIENTISSUBADRCVTFM

6-Information

Failed to rcv_transform message - from slot [chars] XDR client [chars] context [dec]

Cannot perform ISSU receive transform. This is likely due to a failure in negotiation earlier or when one side of an ISSU-enabled XDR connection is out of sync with the other.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-6- CLIENTISSUBADTXTFM

6-Information

Failed to xmit_transform message - to slot [chars] XDR client [chars] context [dec]

Cannot perform ISSU transmit transform. This is likely due to a failure in negotiation earlier or when one side of an ISSU-enabled XDR connection is out of sync with the other.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSUNEGATIVEPADDING

3-Error

Negative padding for [chars] slots [chars] msg [dec] padded: [dec] unpadded: [dec]

-

-

-

XDR-3- CLIENTISSUNEGONOTDONE

3-Error

Attempting to push send XDR message [dec] to slots [chars] for [chars] before nego

Internal error. May result in unpredictable behaviour.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-6- CLIENTISSUUNREG

6-Information

Failed to unregister session - XDR client [chars] slot [chars] reason [chars]

Unable to unregister this session. This will likely cause problems when reregistering and should be reported.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSU_REGERROR

3-Error

ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars]

ISSU negotiation failed for this XDR client.

XDR_DDTS_COMPONENT

"This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it."

XDR-3- ISSU_NEGOFAIL

3-Error

ISSU negotiation failed for XDR slot [chars] reason: [chars]

ISSU negotiation failed. XDR on this and the remote slot cannot interoperate. Syncing of information to/from this slot for all XDR clients will not be allowed.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- PRIOCLIENTISSU_NEGOFAIL

3-Error

ISSU negotiation failed for XDR client [chars] slot [chars] reason: [chars]

ISSU negotiation failed for a core XDR client. XDR on this and the remote slot cannot interoperate in SSO mode. Syncing of information to/from this slot will not happen for any XDR client.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSU_NEGOFAIL

3-Error

ISSU negotiation failed for XDR client [chars] slot [chars] reason: [chars]

ISSU negotiation failed. This XDR client on this and the remote slot cannot interoperate in SSO mode. Syncing of information to/from this slot will not happen for this and dependent clients. See output of show xdr multicast for full details.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSU_FOF_REGERROR

3-Error

ISSU client [chars] [dec] entity [dec] message [dec] [chars]

This ISSU client has a message containing a foreign field owned by another client and failed to register this dependency.

XDR_DDTS_COMPONENT

"This error indicates a potential coding problem. It is an error that " "may occur every time this image is run and may require a code change " "to fix it."

XDR-3- CLIENTISSU_FOF_NEGOFAIL

3-Error

ISSU negotiation failed for FOF client [dec] for peer [chars] ISSU peer [dec]

ISSU negotiation failed for a client which has registered ISSU FOF client dependencies. The dependent clients on this and the remote slot cannot interoperate in SSO mode. Syncing of information to/from this slot will not happen for this and the dependent clients. See output of \show xdr multicast\ for full details.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- BYPASSFOFNEGO

3-Error

Bypassing FOF ISSU client [chars] [dec] nego for XDR client [chars] slot [chars]

This XDR client has a dependency on another ISSU client due to having foreign-owned-fields. As the ISSU client that owns the foreign-owned fields is not in the image the XDR client will not wait for that client to finish ISSU negotiation. Appearance of this error message indicates that work is required to add the missing client to the image.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSU_NEGOREGERROR

3-Error

XDR client [chars] failed ISSU negotiation result notification registration for ISSU client [chars] [dec] reason: [chars]

This client has dependency on the succesful ISSU negotiation of another client and failed to register this dependency

XDR_DDTS_COMPONENT

"This error indicates a potential coding problem. It is an error that " "may occur every time this image is run and may require a code change " "to fix it."

XDR-3- CLIENTISSU_NEGOUNREGERROR

3-Error

Failed to unregister ISSU negotiation result notification registration for ISSU client [chars] [dec] reason: [chars]

This client has dependency on the succesful ISSU negotiation of another client and failed to unregister this dependency when not required.

XDR_DDTS_COMPONENT

"This error indicates a potential coding problem. It is an error that " "may occur every time this image is run and may require a code change " "to fix it."

XDR-6- CLIENTNOTREGONRP

6-Information

Client [chars] has registered on slot [chars] before RP.

XDR client has registered on non-RP card before RP card. If this has occurred while toggling the client's registration status rapidly then it may be a transient problem and will resolve itself. If not then the client's status may be unpredictable and ISSU negotiation if platform is ISSU-aware may not take place correctly.

XDR_DDTS_COMPONENT

"Verify whether the client's registration status is the same on both " "the RP and the card on which the problem is reported by comparing " "the output of 'show xdr client all' to see if the client is present or " "absent in BOTH. If so and no other error messages have been seen " "then this is a transient issue and no further action is required. " "Otherwise copy the message exactly as it appears and report it to " "your technical support representative."

XDR-3- XDROOS

3-Error

Received an out of sequence IPC message. Expected [dec] but got [dec] from slot [chars].

An out of sequence IPC message was received

XDR_DDTS_COMPONENT

"We weren't meant to get the IPC message we did. From this point onwards " "IPC can't be relied on. " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3-CLIENTISSUNOMSGGRP

3-Error

Cannot determine ISSU message group for slot [dec]. Unknown [chars]

Not able to determine the set of ISSU messages to be used between local and remote slot due to not being able to determine linecard type for one or other slot. This might be due to a new linecard type.

XDR_DDTS_COMPONENT

LOG_STD_ACTION

XDR-6- XDRREGISTRATION

6-Information

XDR failed to register [chars] client due to [chars]

Failure to register the said XDR client.

XDR_DDTS_COMPONENT

"A failure occured which prohibits the XDR client from registering with " "the core. " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-6- XDRINVALIDHDR

6-Information

XDR for client [chars] dropped slots:[chars] from slot:[chars] context:[dec] length:[dec]

The XDR message was dropped for the reason given.

XDR_DDTS_COMPONENT

"If the failure was due to an invalid context for the CEF push client " "and occurred during an ISSU upgrade then it may be safely ignored. " "Otherwise: " LOG_STD_ACTION

XDR-6- XDRINVALIDHDRISSU

6-Information

XDR ISSU negotiation message for client [chars] dropped

The XDR ISSU negotiation message was dropped for the reason given.

XDR_DDTS_COMPONENT

"If the message occurred during an ISSU upgrade then it may be " "safely ignored. Otherwise: " LOG_STD_ACTION

XDR-6- XDRMCASTINIT

6-Information

XDR mcast subsystem initilisation error: [chars]

XDR non functional.

XDR_DDTS_COMPONENT

"A failure occured which prohibits the XDR client from registering with " "the core. " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- CLIENTISSU_PUSHFAIL

3-Error

Attempting to push send XDR message [chars] to slots [chars] via XDR client

Internal error. May result in unpredictable behaviour.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show issu message types [XDR client ISSU ID]\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- XDRMCASTJOIN

3-Error

Attempt to join [chars] to [chars] failed because client [chars] returned an error

Internal error. May result in unpredictable behaviour.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show monitor event-trace xdr all\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- XDRMCASTJOINREQ

3-Error

Client [chars] returned an invalid response to a join request for groups [chars] and [chars]

Internal error. May result in unpredictable behaviour.

XDR_DDTS_COMPONENT

"Get the output of \"show xdr multicast\" \"show xdr client all\" and " "\"show monitor event-trace xdr all\". " "Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- MSGSIZEFAIL

3-Error

The IPC message size is out of bounds The ipc_msg_size is : [dec] while the maximum size we can handle is the XDR_IPC_BUFFER_SIZE : [dec] .

The size of the IPC message that was received is out of bounds

XDR_DDTS_COMPONENT

"We were not meant to get the IPC message we did. The size of the IPC " "message is larger than the maximum size that can be handled. " "This is probably due to communication incompatibility issues between the " "active and the standby RPs. " "Please report it to your technical support representative."

XDR-3- XDRMCAST_PEER_BINDING

3-Error

XDR peer [chars] bind to group [chars] was bound to [chars]: [chars]

-

-

-

XDR-3- XDRMCASTGRPINVALID

3-Error

Invalid XDR multicast group for slots [chars]: [chars]

-

-

-

XDR-3- ILLEGAL_CAP_TYPE

3-Error

Illegal ISSU capability type [dec] for XDR client [chars]

Capability type requested is invalid. The named XDR client may not function as expected.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- ILLEGAL_CAP_VALUE_CHANGE

3-Error

ISSU capabilities for peers running same IOS version must be supported.

Basic assumption is that all peers running the same IOS version as the active RP will support the same ISSU capabilities as the active RP. This is an attempt to mark one such peer as not supporting all capabilities. This will break assumptions in XDR ISSU code and cannot be allowed. The traceback will indicate the offending XDR client.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- MISMATCHED_ISSU_CAPABILITY_INFO

3-Error

[chars]: [chars]

ISSU-aware XDR clients may have capabilities to negotiate. They can ask XDR to manage the state of these but must provide all relevant supporting functions to do so. In this case the given client has not done so.

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3-ONINT

3-Error

Invalid operation [chars] at interrupt level by XDR client [chars]

Invalid operation at interrupt level

XDR_DDTS_COMPONENT

"Copy the message exactly as it appears and report it to your technical " "support representative."

XDR-3- FRAG_CLIENT_NOT_ALLOWED

3-Error

Received an XDR fragment from client [chars] slot [chars] which is not allowed to send fragments

Certain clients are restricted by XDR from fragmenting their data yet such a fragment was received received.

XDR_DDTS_COMPONENT

LOG_STD_ACTION

XDR-3- DATA_TOO_LARGE

3-Error

Data length [dec] exceeds limit of [dec] bytes

An attempt was made by a client to send XDR data that was over the given length limit which caused the send to fail.

XDR_DDTS_COMPONENT

LOG_STD_ACTION

XDR-4-FAILATTEMPTOPENIPCPORT

4-Warning

Attempt to open the IPC ports failed. [chars]

XDR failed an attempt to open the IPC port to communicate to the specified peer

XDR_DDTS_COMPONENT

LOG_STD_NO_ACTION

WCCP-1-SERVICELOST

1-Alert

Service [chars][chars][chars] lost on WCCP client [chars]

WCCP has lost the service associated the specified WCCP client

wccp

"Verify the operation of the specified WCCP client"

WCCP-5-SERVICEFOUND

5-Notice

Service [chars][chars][chars] acquired on WCCP client [chars]

WCCP has acquired a service on the specified WCCP client

wccp

LOG_STD_NO_ACTION

WCCP-5-SERVICEMISMATCH

5-Notice

Service [chars][chars][chars] mismatched on WCCP client [chars]

WCCP has rejected a mismatched service on the specified WCCP client

wccp

"Amend the WCCP service definition"

WCCP-3-MASKACLMERGE

3-Error

Mask/ACL merge failed for the service [chars] VRF [chars] service Id [dec]

An internal error indicating that the Mask/ACL merge has failed

wccp

LOG_STD_ACTION

WCCP-1-SERVICELIST

1-Alert

Failed to derive service [chars][chars][chars] from service-list [chars]

The WCCP Access Control List used to define the specified closed service has been modified and can no longer be used to create the service. The service has been marked as inactive. Either change the configuration to an Open service or update the ACL to correctly identify the desired service

wccp

"Update the service-list ACL to correctly define the desired service"

WCCP-3-SBCREATEFAIL

3-Error

Unable to allocate [chars] WCCP subblock on interface [chars]

An internal error indicating that the WCCP process was unable to allocate memory to hold interface specific service information

wccp

"Ensure that there is enough memory available for all processes"

WCCP-3-SBADDFAIL

3-Error

Unable to add [chars] WCCP subblock on interface [chars]

An internal error indicating that the WCCP process was unable to attach interface specific service information

wccp

"Ensure that there is enough memory available for all processes"

WCCP-3-BADACE

3-Error

Service [chars][chars][chars] invalid access-list entry seq:[dec] reason:[chars]

-

-

-

WCCP-3-SBINIT

3-Error

Error initializing [chars] WCCP subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

wccp

LOG_STD_ACTION

WCCP-3-CAP_API_INI

3-Error

Failed to initialize WCCP platform parameter [dec]

Initialization of a WCCP platform parameter failed.

wccp

LOG_STD_ACTION

WCCP-3-CAP_API_DEF

3-Error

Failed to set WCCP platform parameter defaults 0x%X [chars]

The platform failed to set the WCCP platform parameter defaults.

wccp

LOG_STD_ACTION

WCCP-3-CAP_API_GET

3-Error

Failed to get WCCP platform parameter [dec] [chars]

The platform failed to read a WCCP platform parameter.

wccp

LOG_STD_ACTION

WCCP-3-CAP_API_SET

3-Error

Failed to set WCCP platform parameter [dec] to [dec] [chars]

The platform failed to modify a WCCP platform parameter.

wccp

LOG_STD_ACTION

WCCP-3-SIFIGNORED

3-Error

source-interface [chars] ignored [chars]

The configured source interface has been ignored whilst determining the WCCP router ID.

wccp

"Use the indicated reason message to determine why WCCP refused to use " "the configured interface as its router ID."

ETHER_PLATFORM_SW-3-DOT1AH_DEL_MAP_FAILED

3-Error

Unable to remove 802.1ah mapping entry for B-MAC [enet] C-MAC [enet].

The Ethernet Software Platform was unable to remove an 802.1ah mapping entry from the tree of entries.

ether-infra

"This error may be transient. If the error " "persists you may need to reload the router."

ETHER_PLATFORM_SW-3-DOT1AH_CHNK_LCK_FAILED

3-Error

Unable to lock memory while learning C-MAC to B-MAC mapping

The Ethernet Software Platform was unable to lock a particular piece of memory while attempting to learn a C-MAC to B-MAC mapping

ether-infra

"This error may be transient. If the error " "persists you may need to reload the router."

ETHER_PLATFORM_SW-3-DOT1AH_PROC_ENQ_FAILED

3-Error

Unable to enqueue a request to learn a C-MAC to B-MAC mapping

An error occurred while trying to enqueue a request to learn a C-MAC to B-MAC mapping.

ether-infra

"This error may be transient. If the error " "persists you may need to reload the router."

ETHER_PLATFORM_SW-3-EFP_CANNOT_CLEAR_DIM

3-Error

Unable to clear EFP's encapsulation data

An error occurred while trying to clear the encapsulation data for an EFP.

ether-infra

"Enable debugging with 'debug ethernet service " "instace'. Retry the operation that caused the " "error to see if additional debugging messages " "are provided. If the error persists you may need " "to reload the router."

ETHER_PLATFORM_SW-3-REWRITE_FAILED

3-Error

Unable to apply rewrite to packet

An error occurred while trying to perform an ingress rewrite operation on a frame.

ether-infra

"This error may be transient. If the error " "persists you may need to reload the router."

ETHER_PLATFORM_SW-3-BD_NULL

3-Error

Unable to get bridge-domain [dec] information for EFP [dec]

The software dataplane was unable to get the bridge-domain information for the EFP.

ether-infra

"This error may be transient. If the error " "persists you may need to reload the router."

ETHER_PLATFORM_SW-3-NO_PD_EFP

3-Error

Unable to find software platform EFP information for EFP ID [dec]

The software dataplane was unable to get the platform dependent EFP information for the EFP with the given ID.

ether-infra

"This error may indicate a bug in the software " "dataplane implementation. If the error " "occurs after a specific configuration was performed " "then precisely record those configuration steps. " "Contact your Cisco technical support " "representative and provide the gathered " "information."

ETHER_SERVICE_IPC-3-IPCPORT_CREATE

3-Error

Unable to create IPC port [chars].

Ethernet Service was unable to create an IPC port

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-3-IPCPORT_REGISTER

3-Error

Unable to register IPC port [chars].

Ethernet Service was unable to register an IPC port

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-3-IPCPORT_REMOVE

3-Error

Unable to remove IPC port [chars].

Ethernet Service was unable to remove an IPC port

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-3-IPCPROCESSES

3-Error

Unable to create IPC processes on [chars].

Ethernet Service was unable to create IPC processes

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-4-NOIPCPORT

4-Warning

IPC port is NULL [chars]

Ethernet Service cannot send the message as the IPC port information is NULL. This is a warning message no action is required.

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-4-NOMESSAGE

4-Warning

Message is NULL [chars]

Cannot send the message as the message is NULL. This is a warning message no action is required

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-4-NOIPCDATA

4-Warning

IPC Message has no data area [chars]

Cannot find data area in an IPC message. This is a warning message no action is required

ether-infra

"Copy the error message exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE_IPC-3-IPCSESSION

3-Error

Unable to open an IPC session for communicating with [chars]. Error: [chars]

This is an internal error

ether-infra

"Copy the error message exactly as it appears and report it to your" " technical support representative."

ETHER_SERVICE_IPC-3-NOIPCDESC

3-Error

Unable to allocate IPC descriptor for Ethernet Service on [chars].

This is an internal error

ether-infra

"Copy the error message exactly as it appears and report it to your" " technical support representative."

ETHER_SERVICE_IPC-3-NOMEM

3-Error

Unable to allocate memory for Ethernet Service on [chars].

This is an internal error

ether-infra

"Copy the error message exactly as it appears and report it to your" " technical support representative."

ETHER_SERVICE_IPC-3-IPC_TRANSMIT_FAILED

3-Error

IPC message transmission failure [chars]

An error was detected when transmitting an IPC message between Standby RP and SP. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred.

ether-infra

"This could be a transient error. If this error persists " "copy the error message exactly as it appears and report it " "to your technical support representative."

ETHER_SERVICE_IPC-3-IPC_RESP_ERROR

3-Error

IPC send response error [chars]

An error was detected in the response for an IPC message that was transmitted to the peer.

ether-infra

"This error could be transient. If this error persists " "copy the error message exactly as it appears " "and report it to your technical support representative."

ETHER_SERVICE_IPC-3-RMI_FAILED

3-Error

Ethernet Infra failed to register with the Resource Manager RMI [chars]

Ethernet Infra registers with the Resource Manager RMI to

ether-infra

"show tech"

ETHER_SERVICE_IPC-3-RMI_CALLBACK

3-Error

Ethernet Infra encountered an error while processing a callback from the Resource Manager RMI [chars]

Ethernet Infra registers with the Resource Manager RMI to

ether-infra

"show tech"

ETHER_INFRA_HA-2-INIT

2-Critical

Ether INFRA ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Ether INFRA ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ether-infra

LOG_STD_ACTION

ETHER_INFRA_HA-3-TRANSFORM

3-Error

Ether INFRA ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Ether INFRA ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether INFRA state between the active device and the standby device is not identical.

ether-infra

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_INFRA_HA-3-MSG_NOT_OK

3-Error

Ether INFRA ISSU client 'Message Type [dec]' is not compatible

The Ether INFRA ISSU client received an incompatible message from the peer device. The message cannot be processed.

ether-infra

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_INFRA_HA-3-MSG_SIZE

3-Error

Ether INFRA ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Ether INFRA ISSU client failed to calculate the MTU for the specified message. The Ether INFRA ISSU client will not able to send the message to the standby device.

ether-infra

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_INFRA_HA-3-INVALID_SESSION

3-Error

Ether INFRA ISSU client does not have a valid registered session.

The Ether INFRA ISSU client does not have a valid registered session.

ether-infra

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_INFRA_HA-2-SESSION_REGISTRY

2-Critical

Ether INFRA ISSU client failed to register session information. Error: [dec] [chars]

The Ether INFRA ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ether-infra

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_INFRA_HA-3-SESSION_UNREGISTRY

3-Error

Ether INFRA ISSU client failed to unregister session information. Error: [dec] [chars]

The Ether INFRA ISSU client failed to unregister session information.

ether-infra

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_INFRA_HA-2-SESSION_NEGO

2-Critical

Ether INFRA ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Ether INFRA ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ether-infra

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_INFRA_HA-2-SEND_NEGO_FAILED

2-Critical

Ether INFRA ISSU client failed to send negotiation message. Error: [dec] [chars]

The Ether INFRA ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ether-infra

"show logging and show checkpoint client"

ETHER_INFRA_HA-2-GET_BUFFER

2-Critical

Ether INFRA ISSU client failed to get buffer for message. Error: [dec] [chars]

The Ether INFRA HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly.

ether-infra

"show logging and show checkpoint client"

ETHER_SERVICE-6-EVC_VLAN_NOT_CONFIGURED

6-Information

VLANs [chars] not configured at [chars] but is in a CEVLAN/EVC map

VLANs part of the CEVLAN/EVC map for an EVC associated to an interface but the interface doesn't have those VLANs configured

ether-infra

"Verify configurations of VLANs on the interface"

ETHER_SERVICE-6-EVC_STATUS_CHANGED

6-Information

status of [chars] changed to [chars]

EVC status has changed

ether-infra

"No Action"

ETHER_SERVICE-6-UPDOWN

6-Information

Service instance [dec] on interface [chars] changed to [chars]

Service instance shutdown due to errdisable

ether-infra

"No Action"

ETHER_SERVICE-6-ERR_DISABLED

6-Information

[chars] - shutdown service instance [dec] at [chars]

Service instance shutdown due to errdisable

ether-infra

"No Action"

ETHER_SERVICE-4-UNSUP_MIRPENABLE

4-Warning

%% Not supported since \no ethernet mac-flush notification mirp\ command is configured.

\no ethernet mac-flush notification mirp\ is configured.

ether-infra

"Configure \"ethernet mac-flush notification mirp\" command."

ETHER_SERVICE-3-EFP_NO_MEMORY

3-Error

[chars] : memory allocation failed for [chars]

memory allocation failed

ether-infra

"'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help."

ETHER_SERVICE-3-EFP_NULL_POINTER

3-Error

[chars] : [chars] pointer is NULL

NULL pointer

ether-infra

"Copy the error and send it to TAC"

ETHER_SERVICE-3-EFP_INVALID_TYPE

3-Error

[chars] : [chars] is INVALID

invalid type

ether-infra

"Copy the error and send it to TAC"

ETHER_SERVICE-3-ETHER_CHAN_SERV_INSTANCE_POLICY_REMOVED

3-Error

[chars] service policy [chars] has been removed from service instance [dec] of ethernet channel [chars] due to failure to install the policy on member link [chars].

The member link does not support the service policy or installation failed due to resources limitation at the time.

ether-infra

"Check for any error message that indicates incompatiblity between " "the policy and the member link. Remove the member link from the " "ethernet channel and reconfigure the policy on the service instance. " "If the problem persists copy the error exactly as it appears and " "report it to your technical support representative."

ETHER_SERVICE-3-EFP_DEBUG_INIT_FAILURE

3-Error

The Ether Infra Trace and Debug Library Failed to initialize successfully due to error: [dec]

All trace and debug may not work

ether-infra

"No Action"

NETCLK-6-SRC_REM

6-Information

Synchronization source [chars] is removed from [chars] selection process.

Synchronization source is removed from synchronization source selection processes i.e. T0 or selection process per T4.

sync-e

LOG_STD_NO_ACTION

NETCLK-6-ALL_SRC_REM

6-Information

All synchronization sources have been removed from [chars] selection process.

All synchronization sources are removed from synchronization source selection processes i.e. T0 or selection process per T4.

sync-e

LOG_STD_NO_ACTION

NETCLK-6-SRC_ADD

6-Information

Synchronization source [chars] is added to [chars] selection process.

Synchronization source is added to synchronization source selection processes i.e. T0 or selection process per T4.

sync-e

LOG_STD_NO_ACTION

NETCLK-6-SRC_UPD

6-Information

Synchronization source [chars] status [chars] is posted to all selection process.

Synchronization source status event is updated to synchronization

sync-e

LOG_STD_NO_ACTION

NETCLK-6-SEL_CLOCK_SRC

6-Information

Synchronization source [chars][chars] is selected by selection processT0

Synchronization source selection process has selected source q receive clock to synchronize the system and generate T0transmit SEC clock. T0 clock is used as TX clock on all

sync-e

LOG_STD_NO_ACTION

NETCLK-6-SEL_T4_CLOCK_SRC

6-Information

Synchronization source [chars] is selected by selection process to synchronize the system and generate T4[chars] output[chars]

Synchronization source selection process for T4external interface

sync-e

LOG_STD_NO_ACTION

NETCLK-6-ENTER_HOLDOVER

6-Information

System Internal synchronization source is selected.

System Internal synchronization source Internal is selected as all other nominated synchronization source are not valid for Synchronization selection process.

sync-e

LOG_STD_NO_ACTION

NETCLK-6-INV_QL

6-Information

invalid QL [chars] received for [chars] on network option [chars].

The platform has notify RP the clock quality of an input source. But the value appears to be invalid based on the current configured network option.

sync-e

LOG_STD_NO_ACTION

NETCLK-4-FAIL

4-Warning

The Network Clock protocol has encountered the error: [chars].

The protocol has run into a failure condition. The reason should be given in the parenthesis.

sync-e

"show network-clock synchronization and " "show network-clock synchronization detail and " "show module"

NETCLK-4-PD_REG

4-Warning

[chars] [dec]

The platform has failed to provide the protocol one of the mandatory functions.

sync-e

LOG_STD_ACTION

NETCLK-6-QL_CHANGE

6-Information

Input QL for [chars] is [chars]

The input QL used for a network-clock input changed

sync-e

LOG_STD_NO_ACTION

NETCLK-3-ESMC_EVENT_CREATE_FAIL

3-Error

Failed to create ESMC event.

Failed to create an ESMC event to be queued.

sync-e

LOG_STD_NO_ACTION

NETCLK-3-ESMC_EVENT_ENQUEUE_FAIL

3-Error

Failed to enqueue ESMC event.

Failed to add an ESMC event to the event queue.

sync-e

LOG_STD_NO_ACTION

NETCLK-3-ESMC_EVENT_QUEUE_INIT_FAIL

3-Error

Failed to initialize ESMC event queue.

Failed to initialize the ESMC event queue.

sync-e

LOG_STD_NO_ACTION

NETCLK-3-ESMC_EVENT_QUEUE_ALLOC_FAIL

3-Error

Failed to allocate memory for ESMC event queue.

Failed to allocate memory for the ESMC event queue.

sync-e

LOG_STD_NO_ACTION

PTP-6-CLK_STATUS_UPDATE

6-Information

Slave clock status changed to [chars] : [chars].

Clock status update for the Precision Timing Protocol

ptp

LOG_STD_NO_ACTION

PTP-6-CLK_MASTER_PORT_SELECTED

6-Information

slave clock port [chars] master address new:[chars] old:[chars]

A slave port may associate with multiple master port addresses. This message describes the address of the selected master port.

-

LOG_STD_NO_ACTION

PTP-4-CLK_INV_MASTER_PORT_SELECTED

4-Warning

slave clock port [chars] invalid master address [chars] is selected. Action is ignored because of the invalid master clock source.

A master source address is selected which is either invalid or non-existent in the current list of master source addresses.

ptp

LOG_STD_ACTION

CDP-4-DUPLEX_MISMATCH

4-Warning

duplex mismatch discovered on [chars] [chars] with [chars] [chars] [chars].

CDP discovered a mismatch of duplex configuration

-

"Configure the interfaces to the same duplex full or half."

CDP-4-NATIVE_VLAN_MISMATCH

4-Warning

Native VLAN mismatch discovered on [chars] [dec] with [chars] [chars] [dec].

CDP discovered a mismatch of native-VLAN configuration

-

"Configure the interfaces to the same native VLAN."

CDP-3-CHUNK

3-Error

Chunk_malloc Failure

chunk malloc failure

cdp

LOG_STD_ACTION

CDP-6-TLV_LIST_GLOBALLY

6-Information

Tlv-list [chars] [chars] globally on all interfaces.

CDP Tlv-list configuration Globally.

-

"No action required. The message is informatory in nature."

CDP-6-TLV_LIST_INTERFACE

6-Information

Tlv-list [chars] [chars] interface [chars]

An IPv6 process could not be started. This machine will not be able to process any IPv6 packets.

ipv6

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

IPV6_FORWARDING-3-UNFRAGMENTABLE

3-Error

Cannot fragment packet: unfragmentable part length [dec] MTU of [dec]

An internal software error occurred. A single packet originated by this system could not be fragmented and has been dropped. Normal system operation continues.

ipv6

-

IPV6_FORWARDING-3-NULLPAK

3-Error

Uninitialized buffer pointer - [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_FORWARDING-3-NULLIDB

3-Error

Uninitialized interface pointer - [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

IPV6_FORWARDING-4-MULTICAST

4-Warning

Application does not support multicast destination address %P packet dropped.

-

-

-

IPV6_ICMP-3-NULLPAK

3-Error

Uninitialized buffer pointer - [chars]

An internal software error occurred.

ipv6

LOG_STD_ACTION

PMIPV6-5-TUNNELDELETE

5-Notice

Deleting the Proxy Mobile IPv6 tunnel [chars]

The PMIPv6 tunnel is being deleted.

mipv6

"If you suspect this condition contact technical\n\ support representative with the output of show tech"

PMIPV6-5-TUNNELUP

5-Notice

Bringing up the Proxy Mobile IPv6 tunnel [chars]

The PMIPv6 tunnel is being deleted.

mipv6

"If you suspect this condition contact technical\n\ support representative with the output of show tech"

OFP-3-ERR

3-Error

[chars]

OpenFlow Agent has experienced an internal software problem.

openflow-agent

LOG_STD_ACTION

OFP-5-CONFIG

5-Notice

[chars]

OpenFlow Agent information usually configuration command.

openflow-agent

"None"

OFP-6-INFO

6-Information

[chars]

OpenFlow Agent information action may not be required.

openflow-agent

"None"

OFP-4-WARN

4-Warning

[chars]

OpenFlow Agent warning information action may be required.

openflow-agent

LOG_STD_ACTION

OFP-3-ASSERT

3-Error

[chars]

OpenFlow Agent has experienced an internal software problem.

openflow-agent

LOG_STD_ACTION

ERROR-3-OF_AGENT

3-Error

ERRMSG_NOFLAGS

-

-

-

INFO-6-OF_AGENT

6-Information

ERRMSG_NOFLAGS

-

-

-

WARNING-4-OF_AGENT

4-Warning

ERRMSG_NOFLAGS

-

-

-

ERROR-3-OVS

3-Error

ERRMSG_NOFLAGS

-

-

-

INFO-6-OVS

6-Information

ERRMSG_NOFLAGS

-

-

-

SBC_CFG-3-DBE_CONFIG_FAILURE

3-Error

An SBC DBE configuration failure has occurred.

SBC has been unable to apply its DBE configuration.

sbc-comp

"Attempt to manually reconfigure the SBC DBE. " LOG_STD_ACTION

SBC_CFG-6-SERVICE_CHANGE_COLD_BOOT

6-Information

Delay [chars].

SBC has been configured to delay sending a ServiceChange message at boot. Upon the delay timer expiring the ServiceChange message will be sent.

sbc-comp

"This message is for informational purposes only. " "A ServiceChange message will be sent out once the " "delay timer expires."

SBC_CFG-4-SERVICE_CHANGE_COLD_BOOT_DELAY_FAILED

4-Warning

Failed to delay ServiceChange.

SBC has failed to start a timer for delaying a ServiceChange message at boot. The ServiceChange message will be sent out without a delay.

sbc-comp

"Ensure that SBC has been fully Activated and " "that all requested pinholes have been established. " LOG_STD_ACTION

SBC_CFG-3-SERVICE_CHANGE_COLD_BOOT_FAILED

3-Error

Delayed ServiceChange failed.

SBC has failed to send the delayed ServiceChange message at boot.

sbc-comp

"Ensure that the SBC configuration is valid " "and perform a manual SBC Activation."

SBC_CFG-3-MED_NOT_DEL_V4

3-Error

IPv4 addresses deleted %I %I VRF '[chars]'

One or more IPv4 addresses of an SBC interface were removed while the SBC was still active. Please remove the media addresses/pools later manually. If the media addresses/pools were associated with a VRF then it will be necessary to remove the media addresses/pools by unconfiguring the SBC.

sbc-comp

-

SBC_CFG-3-MED_NOT_DEL_V6

3-Error

IPv6 addresses deleted %P/[dec] VRF '[chars]'

One or more IPv6 addresses of an SBC interface were removed while the SBC was still active. Please remove the media addresses/pools later manually. If the media addresses/pools were associated with a VRF then it will be necessary to remove the media addresses/pools by unconfiguring the SBC.

sbc-comp

-

SBC_CFG-3-SBC_NOT_CONFIG

3-Error

SBC is not configured. VOIP LI configuration request failed

Since SBC is not configured the VOIP LI request is rejected. First configure SBC and then VOIP LI requests will be processed.

sbc-comp

-

SBC_CFG-4-BLACKLIST_CLEARED

4-Warning

Source [chars]: cleared blacklist event or alert reason: [chars]

A blacklist event or alert is cleared.

sbc-comp

-

SBC_CFG-4-BLACKLIST_MINOR

4-Warning

Source [chars]: minor blacklist alert reason: [chars]

A minor blacklist alert has been generated.

sbc-comp

-

SBC_CFG-4-BLACKLIST_MAJOR

4-Warning

Source [chars]: major blacklist alert reason: [chars]

A major blacklist alert has been generated.

sbc-comp

-

SBC_CFG-4-BLACKLIST_CRITICAL

4-Warning

Source [chars]: critical blacklist alert reason: [chars]

A critical blacklist alert has been generated.

sbc-comp

-

SBC_CFG-4-BLACKLIST_BLOCKED

4-Warning

Source [chars]: blacklisted blocked reason: [chars]

The source is blacklisted.

sbc-comp

-

SBC_COMP-3-MEMORY_ALERT

3-Error

SBC memory congestion level has changed from [chars] to [chars].\n Usage: [dec] of [dec] bytes.

SBC has reported a processor memory change.

sbc-comp

-

SBC_COMP-3-MEMORY_REJ

3-Error

SBC is rejecting new INVITES due to memory congestion state.\n Usage: [dec] of [dec] bytes.

SBC has reported a rejected a new call due to memory state.

sbc-comp

-

RLC_ISSU_PROCESS_CLI-3-NULL_SLOTINDEX

3-Error

slotindex can not be NULL.

slotindex can not be NULL.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why slotindex is NULL"

RLC_ISSU_PROCESS_CLI-3-NULL_RED_CONFIG

3-Error

Redundancy configuration can not be NULL.

Redundancy configuration can not be NULL.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why redundancy configuration is NULL"

RLC_ISSU_PROCESS_CLI-3-RLC_ISSU_ERR

3-Error

[chars]

An error occurred while executing Redundanct LC ISSU CLI

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-NULL_RED_CONFIG

3-Error

Redundancy configuration can not be NULL.

Redundancy configuration can not be NULL.

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why redundancy configuration is NULL"

RLC_ISSU_PROCESS-3-RLC_ISSU_ERR

3-Error

[chars]

An error occurred while running the Redundanct LC ISSU process

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-RLC_ISSU_NOTIF_ERR

3-Error

LC ISSU is terminated for due to [chars] use \n\'issu linecard abortversion [chars]' to restore linecard to the original version if necessary

An error notification was received while running the \n\Redundanct LC ISSU process. The process is stopped

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-RLC_ISSU_MLC_FSM_ERR

3-Error

error processing [chars] event in [chars] state for LC [chars] terminating process

internal error in RLC ISSU event processing

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-RLC_ISSU_RLD_PLC_FSM_ERR

3-Error

error processing [chars] event in [chars] state for LC idx [chars] terminating process

internal error in RLC ISSU event processing

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-4-RLC_ISSU_IMAGE_ERR

4-Warning

error loading LC image for LC [chars]

internal error in loading linecard image

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-RLC_ISSU_N1_PLC_FSM_ERR

3-Error

error processing [chars] event in [chars] state for LC [chars] terminating process

internal error in RLC ISSU event processing

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-RLC_ISSU_N1_PLC_PSLC_ERR

3-Error

prepareversion error secondary LC not standby ready for LC [chars]

the secondary LC failed to become standby ready

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-3-RLC_ISSU_N1_PLC_WPLC_ERR

3-Error

runversion error primary LC [chars] not standby ready

the primary LC is not ready for switchover

ha-issu-infra

"Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why this error occurs"

RLC_ISSU_PROCESS-4-RLC_ISSU_NOT_COMPLETED_WARNING

4-Warning

LC ISSU is not finished please issue the next commands to complete LC ISSU

The steps to complete LC ISSU has not been fully carried\n\out by the operator. The system is left in an intermediate state where some \n\linecards have been upgraded and others have not. This message is to remind\n\the operator that a significant amount of time has passed waiting for \n\the operator to enter the next LC ISSU command.

ha-issu-infra

"Enter the next LC ISSU command to continue with\n\LC ISSU which includes commands to perform the operations of prepareversion \n\loadversion runversion acceptversion commitversion or abortversion"

RLC_ISSU_PROCESS-4-LCRPVERSION

4-Warning

Linecard [chars] and RP have different image versions

Linecard has different version of image than RP

ha-issu-infra

"Use RLC ISSU commands to change these\n\ LCs' images to same version as RP"

RLC_ISSU_PROCESS-5-RLC_ISSU_NOTIF

5-Notice

[chars]

Linecard notification msg

ha-issu-infra

"No action needed"

ENTROPY-0-ENTROPY_ERROR

0-Emergency

Unable to collect sufficient entropy

On bootup the device attempts to collect entropy to initialize its random number generator. This device has failed to do so. Because of this most security protocols will not run

-

"This is probably a hardware failure"

DTI-3-DTI_ERROR

3-Error

DTI Error

First DTI error message

rfgw-sw-sup

LOG_STD_NO_ACTION

TAC-6-SENDTMO

6-Information

Send type [dec] to [inet] timed out

A background TACACS notification enabled with the command tacacs notify was not acknowledged by the TACACS server processor within the

-

"Check the TACACS server and the network attached to it."

TAC-4-UNEXREP

4-Warning

Reply for non-existent request [dec] on queue

The TACACS facility received a message it was not expecting. This may occur when a TACACS server sends duplicate responses or when it responds to a request that has already timed out. It also may be due to an internal software problem.

-

"If this message recurs call your technical support representative for " "assistance."

TAC-3-XTACACL

3-Error

[chars]: accesslist 0x[hec] out of range for \[chars]\

The TACACS facility created a message that contains an accesslist which is not a valid accesslist out of bounds.

tacacs

"If this message recurs call your technical support representative for " "assistance."

TAC-4-NOTIMEOUT

4-Warning

Warning: This command has been deprecated in favor of the line-command \timeout login response\

This command is deprecated and should no longer be used. Instead the line-command <CmdBold>timeout login response<noCmdBold> now provides this functionality

aaa

"Use the line-command <CmdBold>timeout user-response<noCmdBold>"

TAC-3-PICKCTX

3-Error

No pick-context

The context to pick the next server has disappeared.

tacacs

LOG_STD_ACTION

TAC-4-SERVREF

4-Warning

Warning: Server [chars]:[dec] is still referenced by server group.

The server being removed is still referenced by a server group

aaa

"Please dereference the server from the server group " "as soon as possible."

TAC-4-SERVREFNAME

4-Warning

Warning: Server [chars] is still referenced by server group.

The server being removed is still referenced by a server group

aaa

"Please dereference the server from the server group " "as soon as possible."

TAC-3-SERVNO

3-Error

Server [chars] is not configured

The server is not configured

aaa

"Please configure a server before un-configuring it"

TAC-6-SERVDEP

6-Information

tacacs-server host CLI will be deprecated soon. Please move to tacacs server <name> CLI

Migration from tacacs-server host CLI to tacacs server <name> CLI

aaa

"Please try to use new CLI"

TAC-3-SERVCONF

3-Error

Server config failure: [chars]

The server configuration failed

aaa

"Please configure the server properly"

TAC-3-SERVINT

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

TAC-3-SECRETDEFINEFAILED

3-Error

Key definition ignored.

The user is attempting to store either a corrupted shared secret or memory allocation failed during secret definition. Any existing shared secret will be preserved.

aaa

"Configure a proper secret."

TPLUS-3-FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

tplus

"If this message recurs call your technical support representative for assistance."

TPLUS -3-UNKNOWNTYPE

3-Error

TPLUS: 0x%X Unknown Request type [dec].

Unknown request type in client request

tplus

LOG_STD_ACTION

KERBEROS-3-FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs call your technical support " "representative for assistance."

PASSWD-5-AUTH_INVALID_PASSWORD

5-Notice

[chars] [chars] Failed authentication

The credential did not match the configured value when authentication

passwd

"No action required"

PASSWD-5-AUTH_REPEATED_FAILURE

5-Notice

[chars] [chars] number of allowed dauthentication failure exceeded

The number of authentication failures the allowed interval excceeded the configured value

passwd

"No action required"

PASSWD-5-AUTH_LIFETIME_EXCEEDED

5-Notice

[chars] [chars] credential lifetime has expired

The credential has exceeded the configured lifetime

passwd

"No action required"

PASSWD-5-AUTH_PRE_EXPIRY_NOTIFY

5-Notice

[chars] [chars] The credential is about to expiry

The credential is within to pre-expireinterval change the credential expires

passwd

"No action required"

PASSWD-5-CREDENTIAL_COMPLEXITY_CHECK_FAILED

5-Notice

[chars] [chars] credential has failed the complexty check

The credential may not be as secure since it has failed the complexity check

passwd

"No action required"

PASSWD-5-CREDENTIAL_PASSWORD_CHANGE_EXCEED_LIMIT

5-Notice

[chars] [chars] the number of changes allowed has been exceeded

This command syntax has been deprecated.

passwd

"Please use the new syntax and update your saved configuration if needed."

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ this is only a warning

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-6-ACCTLOCAL

6-Information

Username: [chars] Privilege level: [dec] Command: [chars]

AAA local accounting log message

aaa

"This information is to store buffered logs" "locally and send to SYSLOG server"

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-LOCAL_USER_BLOCKED

5-Notice

User [chars] blocked for login till [chars]

User blocked since the number of authentication failures in the watch time exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

AAA_CACHE-3-NULL_TREE_PERIODIC_PROC

3-Error

Cache Tree pointer is of null value

The cache tree pointer is of null value.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

RADPROXY-3-NULL_FSM_CONTEXT

3-Error

Encountered a NULL RP context in [chars]

Encountered a NULL context in RP.

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-INVALID_FSM_STATE

3-Error

Encountered an invalid RP state [dec] in [chars]

An internal RP error occurred.

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-INVALID_FSM_EVENT

3-Error

Received invalid RP event [chars] in state [chars]

An internal RP error occurred.

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-INIT

3-Error

Initialisation failure [chars]

An internal error occurred during RP initialisation.

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-MEMORY_CORRUPT

3-Error

RP Memory magic corrupted

RP memory magic corrupted

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-INVALID_MAC

3-Error

Received invalid MAC [chars] in [chars] from [inet] with NAS-IP [inet]

Error occurred on receiving a invalid MAC

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-MEMORY_LOW

3-Error

Memory low in RP terminating session

System memory is running low.

aaa-protocol

LOG_STD_ACTION

RADPROXY-3-PROTOCOL_VIOLATION

3-Error

RP encountered fatal protocol violation

Unrecoverable protocol error

aaa-protocol

LOG_STD_ACTION

RADIUS-3-SERVERTYPEMISMATCH

3-Error

Servers [chars] and [chars] in server group '[chars]' are of different types.

All the servers in a server group should either be of type standard or non-standard.

aaa

"Enter <CmdBold>show running-config<NoCmdBold> " "command and make sure all the RADIUS servers in " "the server group printed above are of the same " "type - either standard or non-standard."

RADIUS-3-ALLDEADSERVER

3-Error

Group [chars]: No active radius servers found. Id [dec].

This error message occurs when all the servers configured in a server group are found to be unresponsive.

aaa

"Check the network connectivity to the RADIUS " "servers and check that the servers are running."

RADIUS-6-RESETDEADSERVER

6-Information

Group [chars]: Marked alive as Radius server [chars]:[dec][dec] configured.

RADIUS server is now configured in the server group which was previously marked dead.

aaa

"No action required. The message is informatory" "in nature and tells that the dead server is now" "configured and up."

RADIUS-6-SERVERALIVE

6-Information

Group [chars]: Radius server [chars]:[dec][dec] is responding again previously dead.

A RADIUS server which previously was dead has started responding again.

aaa

"No action required. This message is " "informatory in nature and tells that the server " "has come up and running."

RADIUS-6-GETROUTES

6-Information

Retrieving static routes in user [chars]

Getting initial static routes from RADIUS using the given user's profile.

aaa

"No action required. The message is " "informatory in nature and tells that it is getting the " "static routes based on user's profile."

RADIUS-6-GETPOOLS

6-Information

Retrieving IP-Pools via user [chars]

Getting initial IP-Pool definitions from RADIUS using the given user's profile.

aaa

"No action required."

RADIUS-3-NOHOSTNAME

3-Error

Failed to retrieve my hostname.

Could not find the router's hostname. A hostname needs to be defined since it determines the RADIUS profile we will retrieve.

aaa

"Define a hostname on the router's config. " "Refer to the hostname configuration section " "of IOS documentation."

RADIUS-3-FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs enter <CmdBold>show " "tech-support<NoCmdBold> command and call your " "technical support representative for assistance."

RADIUS-3-IDENTFAIL

3-Error

Saving of unique accounting ident aborted. Configuration has been modified.

The configuration has been modified. We can not save the unique accounting IDENT to nvram. The message is to inform the user that the saving of unique accounting ident is aborted due to the change in configuration.

aaa

"Save the configuration and try again. If the error persists " "Enter <CmdBold>show tech-support<NoCmdBold> contact your Cisco " "technical support representative and provide the representative " "with the gathered information for assistance."

RADIUS-6-IDENTSAVE

6-Information

Saving config with new acct ident in nvram.

Saving an accounting ident in nvram. The message is informatory.

aaa

"No action required."

RADIUS-3-OVERRUN

3-Error

Insufficient buffer space [dec] for string value.

This error occurs due to the insufficient memory allocated to the buffer. The condition could be caused by a software less likely by a hardware. The traceback and process information is generated due to this condition.

aaa

"If the error re-occurs check bug toolkit on Cisco web-site " "to look for a bug that has symptoms similar to the " "one occured. If there is no entry for the problem " "you faced collect the system message text exactly " "as it appears on the console or in the system log. " "Enter <CmdBold>show tech-support<NoCmdBold> and contact" "your technical support representative and provide the " "representative with all the information gathered."

RADIUS-3-NOSERVERS

3-Error

No Radius hosts configured or no valid server present in the server group [chars]

RADIUS is attempting to send a request but there are no hosts configured to which the request is send.

aaa

"Configure a host with the 'radius-server' command " "providing the IP address of the server. Refer to " "the radius-server host configuration section of IOS " "documentation."

RADIUS-3-SECRETDEFINEFAILED

3-Error

Key definition ignored.

The user is attempting to store either a corrupted shared secret or memory allocation failed during secret definition. Any existing shared secret will be preserved.

aaa

"Configure a proper secret. Refer to the " "shared secret configuration section for " "RADIUS servers in IOS documentation."

RADIUS-3-FORMATLONG

3-Error

Format string too long.Maximum allowed length is [dec].

The user is attempting to configure a format string with a prefix that is too long.

aaa

"Enter a shorter string to configure."

RADIUS-4-NOSERV

4-Warning

Warning: Server [chars]:[dec][dec] is not defined.

The given server is not globally defined please define it.

aaa

"Please define the server. Refer to the" "server configuration section of IOS documentation."

RADIUS-4-NOSERVNAME

4-Warning

Warning: Server [chars] is not defined.

The given server name is not globally defined please define it.

aaa

"Please define the server. Refer to the " "new server name configuration section of IOS documentation."

RADIUS-4-SERVREF

4-Warning

Warning: Server [chars]:[dec][dec] is still referenced by server group.

The server being removed is still referenced by a server group. This message appears when server configuration is removed but in a server group it still exists.

aaa

"Please dereference the server from the server group " "as soon as possible. Refer to server group configuration " "section in IOS documentation."

RADIUS-4-SERVREFNAME

4-Warning

Warning: Server %S is still referenced by server group.

The server being removed is still referenced by a server group. This message appears when server configuration is removed but in a server group it still exists.

aaa

"Please dereference the server from the " "server group as soon as possible. " "Refer to server group configuration " "section in IOS documentation."

RADIUS-3-NOATTRLIST

3-Error

No attribute-list passed through parser.

An internal error has occurred. The reason could be hardware or software. The error appears when no attribute list is passed through the parser.

aaa

LOG_STD_ACTION

RADIUS-3-INVALIDFORMAT

3-Error

Invalid Nas Port Format: [chars] [chars]

The user is attempting to configure an incorrect format string.

aaa

"Enter a 32 character string using supported " "characters only."

RADIUS-4-BADATTRLIST

4-Warning

Unable to process attribute list.

The attribute list is syntactically incorrect.

aaa

"Please specify the attribute list as a comma-" "delimited string of integers between 1 and 255."

RADIUS-4-NOATTRLISTDEF

4-Warning

Warning: Attribute list [chars] is not defined.

The given attribute list is not defined.

aaa

"Please define the attribute list as soon as " "possible."

RADIUS-3-DATAERROR

3-Error

Warning: [chars]

The given data passed into the Radius subsystem is considered invalid and may result in loss of attributes.

aaa

"Please collect traceback and contact your technical " "support representative."

RADIUS-3-SOURCEPORTALLOCERROR

3-Error

Warning: Unable to allocate port [dec]

Unable to allocate a certain port will not have the full range of source ports. This is not supposed to happen contact support.

aaa

"Contact support"

RADIUS-3-CORRUPTCONTEXT

3-Error

Bad Magic pattern in [chars]:0x[hec] magic:0x[hec]!

The magic pattern imprinted on the internal hash table data structures in RADIUS subsystem is missing and indicates memory corruption. The memory is getting overwritten by a misbehaving process. The traceback and the process information is generated to the result of the error.

aaa

"Check bug toolkit on Cisco web-site to look for a " "bug that has symptoms similar to the one occured. " "If there is no entry for the problem you faced " "collect the system message text exactly as it " "appears on the console or in the system log. " "Enter <CmdBold>show tech-support<NoCmdBold> " "command contact your technical support " "representative and provide the representative " "with the gathered information."

RADIUS-3-UNKNOWNAPI

3-Error

Unknown API type [dec]

RADIUS code has been invoked using an unknown API type. This is the result of a bug in the RADIUS subsystem.

aaa

"Check bug toolkit on Cisco web-site to look for a " "bug which has symptoms similar to the one occured. " "If there is no entry for the problem you faced " "Please collect traceback and contact your" "technical support representative."

RADIUS-3-ZEROATTRLEN

3-Error

Radius attr [dec] len 0

An internal error has occurred

aaa

LOG_STD_ACTION

RADIUS-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

The given server is not on the global public servers list. This is an internal consistency error

aaa

LOG_STD_ACTION

RADIUS-3-NOACCOUNTINGRESPONSE

3-Error

Accounting message [chars] for session %*s failed to receive Accounting Response.

Maximum number of retransmissions is exceeded. The network is not accessible or the RADIUS server is down.

aaa

"Check the network connectivity to the RADIUS " "servers and check that the servers are running. " "If not able to debug the issue enter <CmdBold>show " "running-config<NoCmdBold> and contact your technical " "support representative for assistance."

RADIUS-3-CANNOT_OPEN_SOCKET

3-Error

Cannot open UDP socket for service [chars]

The router is unable to open a socket for UDP communications by the indicated service. Most of the time another service might be using the same port.

aaa

"Check your configuration to make sure that no " "other services are using the same port. " "If not able to debug the issue enter <CmdBold>show " "running-config<NoCmdBold> and contact your technical " "support representative for assistance."

RADIUS-4-NOPUBLICSERV

4-Warning

Warning: No servers were found in the public server list.

The given server is not on the global public servers list. This is an internal consistency error.

aaa

LOG_STD_ACTION

RADIUS-4-RADIUS_DEAD

4-Warning

RADIUS server [chars]:[dec][dec] is not responding.

The server might not be available to serve request. server has not responded to repeated requests.

aaa

"Check for the connectivity to server. " "Check if the RADIUS server is still active. " "If not able to debug the issue enter <CmdBold>show " "running-config<NoCmdBold> and contact your technical " "support representative for assistance."

RADIUS-4-RADIUS_ALIVE

4-Warning

RADIUS server [chars]:[dec][dec] is being marked alive.

A RADIUS server that previously was not responding has responded to a new request or the deadtimer has expired.

aaa

LOG_STD_NO_ACTION

RADIUS-3-MALLOC_FAILED

3-Error

Insufficient memory : [chars].

Memory allocation failed due to insufficient memory

aaa

LOG_STD_NO_ACTION

RADIUS-3-IPV4_FIB_SEND_FAILED

3-Error

Radius ipv4 send failed due to FIB error. Error code: [dec].

Radius not able to send udp packets as fib failed

aaa

LOG_STD_NO_ACTION

RADIUS-3-INVALID_PACKET

3-Error

Invalid packet posted to RADIUS.

Radius not able to process a packet as it in invalid

aaa

LOG_STD_NO_ACTION

SCRIPT_INSTALL-3-SCRPT_TYPE_NOT_MATCHED

3-Error

Script file format invalid: [chars]

The system was able to access and open the script file but file format doesn't contain the expected preamble or the filename doesn't contain the expected extension. The script execution failed as a result of this error.

script_install

"Ensure that the script file contains the expected preample " "in order for it to be accepted as a sintalation script."

SCRIPT_INSTALL-3-SCRPT_FAILED

3-Error

Script execution failed: [chars]

The script file execution encountered an error and failed.

script_install

"This message indicates an internal error in preparing the " "execution of the script. Usually another message with more " "details of the kind of failure is printed on the console. " "Please collect these details and forward to your Cisco " "technical support representative."

SCRIPT_INSTALL-3-SCRPT_UNABLE_TO_OPEN_FILE

3-Error

Unable to open file [chars]

The script file cannot be opened.

script_install

"Check that the script location exists and the file can be accessed " "from the device that tries to access that file for execution." "this is most likely a setup issue."

SCRIPT_INSTALL-3-SCRPT_UNABLE_TO_READ_FILE

3-Error

Unable to read the file [chars]

The script file cannot be read.

script_install

"Check that the script file can be read. " "This checking can be done independent of the device that is trying " "read this file."

SCRIPT_INSTALL-3-SCRPT_UNEXPECTED_FILE_TYPE

3-Error

File is not a script file or not containing ASCII text: [chars]

The script file seems to contain non-ascii text or non-script text.

script_install

"The specified file has to be a script file e.g. TCL script file. " "Check the file URL that it points to a script file."

PNP-6-PNP_SUDI_UPDATE

6-Information

Device SUDI [[chars]] identified

Device SUDI is identified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_BEST_UDI_UPDATE

6-Information

Best UDI [[chars]] identified via [chars]

Best UDI is identified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_GOOD_UDI_UPDATE

6-Information

Good UDI [[chars]] identified via [chars]

Gest UDI is identified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_RELOAD_INFO_ENCODED

6-Information

Reload reason [chars]-[chars] encoded [dec]/[dec] by [chars]

Reload reason encoded

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_RELOAD_INFO_STOPPED

6-Information

Reload reason [chars]-[chars] stopped by [chars]

Reload reason stopped

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DHCP_DISABLED_WHEN_NOTIFIED

6-Information

DHCP option [chars] on interface [chars] disabled when notified [dec]/[dec] by [chars]

DHCP option disabled when notified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DHCP_NON_PNP_OPTION_NOTIFIED

6-Information

DHCP non-PnP option [chars] on interface [chars] notified [dec]/[dec] by [chars]

DHCP non-PnP option notified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DHCP_VALID_PNP_OPTION_NOTIFIED

6-Information

DHCP valid-PnP option [chars] on interface [chars] notified [dec]/[dec] by [chars]

DHCP valid-PnP option notified

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_DHCP_INVALID_PNP_OPTION_NOTIFIED

3-Error

DHCP invalid-PnP option [chars] on interface [chars] notified [dec]/[dec] by [chars]

DHCP invalid-PnP option notified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DNS_SERVER_SET

6-Information

DNS server [chars] set by [chars]

DNS server set

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DOMAIN_NAME_SET

6-Information

Domain name [chars] set on [chars] by [chars]

Domain name set

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_DOMAIN_NAME_NOT_FOUND

3-Error

Domain name not found [dec]/[dec] on [chars] by [chars]

Domain name not found

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_SERVER_IP_RESOLVED

6-Information

PnP server [chars] resolved to ip [chars] on interface [chars] by [chars]

PnP server ip resolved

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_SERVER_IP_UNRESOLVED

3-Error

PnP server [chars] can't be resolved [dec]/[dec] on interface [chars] by [chars]

PnP server can't be resolved

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_CCO_SERVER_IP_RESOLVED

6-Information

CCO server [chars] resolved to ip [chars] by [chars]

CCO server ip resolved

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_CCO_SERVER_IP_UNRESOLVED

3-Error

CCO server [chars] can't be resolved [dec]/[dec] by [chars]

CCO server can't be resolved

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_CCO_PROFILE_UNCONFIGURED

3-Error

CCO Server profile [chars] unconfigured [dec]/[dec] by [chars]

CCO Server profile unconfigured

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_IPV4_RESOLVED_BY

6-Information

IPv4 resolved on interface [chars] by [chars]

IPv4 resolved on interface

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_IPV6_RESOLVED_BY

6-Information

IPv6 resolved on interface [chars] by [chars]

IPv6 resolved on interface

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_CDP_UPDATE

6-Information

Device UDI [[chars]] identified for CDP

Device UDI is identified for CDP

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_CDP_FAILED

6-Information

Failed to identify Device UDI for CDP [dec]/[dec]

Failed to identify Device UDI for CDP

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_CONFIG_ARCHIVE_NOT_SUPPORTED

3-Error

PnP config archive not supported [dec]/[dec] on this platform yet [chars]

PnP config archive not supported on this platform yet

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_CONFIG_ARCHIVE

6-Information

Config [chars] archive [dec]/[dec] by [chars]

Config archive

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_CONFIG_ROLLBACK_NOT_SUPPORTED

3-Error

PnP config rollback not supported [dec]/[dec] on this platform yet [chars]

PnP config rollback not supported on this platform yet

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_CONFIG_ROLLBACK

3-Error

Config [chars] rollback [dec]/[dec] reason [chars] by [chars]

Config rollback

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_IMAGE_INSTALLED_WITHOUT_RELOAD

6-Information

Image [chars] installed without reload [dec]/[dec] by [chars]

Image installed without reload

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_IMAGE_INSTALLED_WITH_RELOAD_SCHEDULED

6-Information

Image [chars] installed with reload scheduled [dec]/[dec] by [chars]

Image installed with reload scheduled

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_IMAGE_INSTALL_FAILED

3-Error

Image [chars] install failed [dec]/[dec] by [chars]

Image install failed

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_TRUSTPOINT_ROLLBACK

3-Error

Trustpoint [chars] rollback [dec]/[dec] reason [chars] by [chars]

Trustpoint rollback

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_TRUSTPOINT_INSTALLED

6-Information

Trustpoint [chars] installed from [chars] by [chars]

Trustpoint installed

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_TRUSTPOOL_INSTALLED

6-Information

Trustpool installed from [chars] by [chars]

Trustpool installed

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_FILE_COPY_DONE

6-Information

File copied to [chars] done [dec]/[dec] bps=[dec] [dec] bytes in [dec] ms by [chars]

File copied done

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_FILE_COPY_FAILED

3-Error

File copied to [chars] failed [dec]/[dec] err=[dec] [[chars]] bps=[dec] [dec] bytes in [dec] ms by [chars]

File copied failed

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_UNABLE_TO_COPY_FILE

3-Error

Unable to copy from [chars] to [chars]. Error [chars]

The file transfer operation failed.

pnpa

"Check that the source file exists and the file can be accessed " "from the device that tries to access that file." "Also check that the URL for both source and destination " " are correct."

PNP-6-PNP_SCRIPT_STARTED

6-Information

Script [chars] started [dec]/[dec] via [chars] by [chars]

Script started

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_PYTHON_SCRIPT_DONE

6-Information

Python script [chars] done [dec]/[dec] via [chars] by [chars]

Python script done

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_TCL_SCRIPT_DONE

6-Information

TCL script [chars] done [dec]/[dec] via [chars] by [chars]

TCL script done

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_PROVISION_DONE

6-Information

PnP Provision done successfully [chars]

PnP Provision done successfully

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_PROVISION_STATE_NOTIFIED

6-Information

PnP Provision state notified [chars]

PnP Provision state notified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_STARTED

6-Information

PnP Discovery started

PnP Discovery started

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_DONE

6-Information

PnP Discovery done successfully [chars] profile [chars] via [chars] [chars]

PnP Discovery done successfully

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_ABORT_ON_VDAEMON

6-Information

PnP Discovery abort on vdaemon input

PnP Discovery has aborted on vdaemon input

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_ABORT_ON_CLI

6-Information

PnP Discovery abort on CLI input

PnP Discovery abort on CLI input

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_ABORT_ON_VIPTELA_STARTUP

6-Information

PnP Discovery abort on Viptela startup config

PnP Discovery abort on Viptela startup config

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_WAITING_ON_SDWAN_TRIGGER

6-Information

PnP Discovery waiting for SDWAN Trigger

PnP Discovery waiting for SDWAN Trigger

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_SDWAN_STARTED

6-Information

PnP SDWAN started [dec] via [chars] by [chars]

PnP SDWAN started

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_SDWAN_STOPPED

6-Information

PnP SDWAN stopped [dec] reason [chars] by [chars]

PnP SDWAN stopped

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_SDWAN_READY

6-Information

PnP SDWAN ready [dec] notified by [chars]

PnP SDWAN ready

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_REDIRECTION_DONE

6-Information

PnP Redirection done [dec] by [chars]

PnP Redirection done

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_STOPPED

6-Information

PnP Discovery stopped [chars]

PnP Discovery stopped

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_LOCATION_TAG_REMOVED

6-Information

PnP Location Tag Removed

PnP Location Tag removed

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_LOCATION_TAG_CHANGED

6-Information

PnP Location Tag Changed [chars]

PnP Location Tag changed

pnpa

LOG_STD_NO_ACTION

PNP-6-HTTP_CONNECTING

6-Information

PnP Discovery trying to connect to PnP server [chars]

PnP Discovery is trying to connect to PnP server

pnpa

LOG_STD_NO_ACTION

PNP-6-HTTP_CONNECTED

6-Information

PnP Discovery connected to PnP server [chars]

PnP Discovery is now connected to PnP server

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_HTTP_TIMED_OUT

3-Error

PnP HTTP timed out [dec]/[dec] on connection to PnP server [chars]

PnP HTTP timed out on connection to PnP server

pnpa

LOG_STD_NO_ACTION

PNP-6-XMPP_CONNECTING

6-Information

PnP Discovery trying to connect to PnP server [chars] port [dec]

PnP Discovery is trying to connect to PnP server

-

LOG_STD_NO_ACTION

PNP-6-XMPP_CONNECTED

6-Information

PnP Discovery connected to PnP server [chars] port [dec]

PnP Discovery is now connected to PnP server

pnpa

LOG_STD_NO_ACTION

PNP-6-PROFILE_CONFIG

6-Information

PnP Discovery profile [chars] configured

PnP Discovery profile is now configured

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_PROFILE_CREATED

6-Information

PnP profile [chars] created [dec]/[dec] by [chars]

PnP profile created

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_PROFILE_DELETED

6-Information

PnP profile [chars] deleted [dec]/[dec] by [chars]

PnP profile created

pnpa

LOG_STD_NO_ACTION

PNP-6-NAPP_CONFIG

6-Information

Command configured: [chars]

PnP Discovery profile is now configured

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_BACKOFF_EXCEEDS_WARNING_LIMIT

6-Information

Requested PnP Backoff time [dec] exceeds warning limit [dec] in seconds

PnP Backoff time exceeds warning limit

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_BACKOFF_NOW

6-Information

PnP Backoff now for [dec] seconds requested [dec]/[dec] by [chars]

PnP Backoff time

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_BACKOFF_TERMINATE

6-Information

PnP Backoff termination requested [dec]/[dec] by [chars]

PnP Backoff termination

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_4G_CONFIG_FAILED

6-Information

PnP 4G Dialer configuration failed after [dec] times

PnP trying to configure 4G Dialer on a cellular interface but failed

-

LOG_STD_NO_ACTION

PNP-6-PNP_MONITOR_WATCH_ENABLED

6-Information

PnP Monitor event [chars] watch [chars] enabled [dec]/[dec] by [chars]

PnP Monitor watch enabled

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_MONITOR_WATCH_DISABLED

6-Information

PnP Monitor event [chars] watch [chars] disabled [dec]/[dec] by [chars]

PnP Monitor watch disabled

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_TLS_TUNNEL_UP_NOTIFIED

6-Information

TLS-Tunnel [chars] up notified [dec]/[dec] by [chars]

TLS-Tunnel down notified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_TLS_TUNNEL_DOWN_NOTIFIED

6-Information

TLS-Tunnel [chars] down notified [dec]/[dec] by [chars]

TLS-Tunnel down notified

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_TLS_TUNNEL_STILL_DOWN_NOTIFIED

3-Error

TLS-Tunnel [chars] still-down notified [dec]/[dec] by [chars]

TLS-Tunnel still-down notified

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_INTERFACE_STILL_DOWN_NOTIFIED

3-Error

Interface [chars] still-down notified [dec]/[dec] by [chars]

Interface still-down notified

pnpa

LOG_STD_NO_ACTION

PNP-3-PNP_SERVER_STILL_UNREACHABLE_NOTIFIED

3-Error

PnP Server still-unreachable notified [dec]/[dec] by [chars]

PnP Server still-unreachable notified

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_MONITOR_EVENT_NOTIFIED

6-Information

PnP Monitor event #[dec] [chars] notified by [chars] at [chars] reason [chars]

PnP Monitor received event notification

-

LOG_STD_NO_ACTION

PNP-6-PNP_MONITOR_EVENT_NOTIFIED_WITH_PROGRESS

6-Information

PnP Monitor event #[dec] [chars] notified by [chars] at [chars] reason [chars] progress [dec]%%

PnP Monitor received event notification with progress percentage

-

LOG_STD_NO_ACTION

PNP-6-PNP_MONITOR_ACTION_DONE

6-Information

PnP Monitor action #[dec] [chars] done for watched event [chars] notified by [chars] at [chars] reason [chars]

PnP Monitor action done for watched event

-

LOG_STD_NO_ACTION

PNP-6-PNP_MONITOR_ACTION_FAILED

6-Information

PnP Monitor action #[dec] [chars] failed for watched event [chars] notified by [chars] at [chars] reason [chars]

PnP Monitor action failed for watched event

-

LOG_STD_NO_ACTION

PNP-6-PNP_RESET_DONE

6-Information

PnP reset done

PnP reset successful

-

LOG_STD_NO_ACTION

PNP-6-PNP_RESET_FAILED

6-Information

Having problem with PnP reset. Try it later.

Failed to do PnP reset

-

LOG_STD_NO_ACTION

PNP-6-PNP_SAVING_TECH_SUMMARY

6-Information

Saving PnP tech summary [chars]... Please wait. Do not interrupt.

PnP saving tech summary to default disk

-

LOG_STD_NO_ACTION

PNP-6-PNP_TECH_SUMMARY_SAVED_OK

6-Information

PnP tech summary [chars] saved successfully elapsed time: [dec] seconds.

PnP tech summary saved to default disk successfully

-

LOG_STD_NO_ACTION

PNP-6-PNP_TECH_SUMMARY_SAVED_WITH_ALARM

6-Information

PnP tech summary [chars] saved with alarm [dec]/[dec] elapsed time: [dec] seconds.

PnP tech summary saved to default disk successfully but with some issues

pnpa

"Make sure that all disks can be recursively listed in resonably short time." " Also never interrupt the PnP tech summary saving in any way e.g." " enable the device console or change any device config or resource."

PNP-6-PNP_TECH_SUMMARY_FAILED_TO_SAVE

6-Information

Having problems saving PnP tech summary [chars] elapsed time: [dec] seconds.

Failed to save PnP tech summary to default disk

pnpa

"Make sure that the default disk has reasonable free space." " Also never interrupt the PnP tech summary saving in any way e.g." " enable the device console or change any device config or resource."

PNP-6-PNP_MODE_CHANGE_IN_PROGRESS

6-Information

Mode change in progress

Mode change in progress

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_MODE_CHANGE_OK

6-Information

Mode change successful device will reload now

Mode change successful device will reload now

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_MODE_CHANGE_FAILED

6-Information

Mode change failed. Use CLI to change mode

Mode change failed

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_STOPPING

6-Information

Stopping PnP Discovery. Please do not interrupt

Stopping PnP Discovery

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_DISCOVERY_NOT_RUNNING

6-Information

PNP Discovery is not running

PNP Discovery is not running

pnpa

LOG_STD_NO_ACTION

PNP-6-PNP_CFG_REG_IGNORE_STARTUP_IS_SET

6-Information

Config register ignore startup config is set PNP won't work

Config register ignore startup config is set PNP won't work

pnpa

LOG_STD_NO_ACTION

XMPP-3-MEMORY

3-Error

[chars]

XMPP subsystem has experienced a problem gettting the required\n\ memory to complete this operation.

xmpp

"Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\n\ upgrading the memory in the network device may be required."

HQF-4-NOT_ENOUGH_BW

4-Warning

interface [chars]: available bandwidth may not meet bandwidth guarantees on direction [chars]

The interface bandwidth is less than the total bandwidth that is required for HQF queuing features on this interface.\n

-

"Increase the bandwidth available on the interface.\n"

HQF-6-ENOUGH_BW

6-Information

interface [chars]: available bandwidth now meet bandwidth guarantees on direction [chars]

The interface bandwidth is now enough for the total bandwidth that is required for HQF queuing features on this interface.\n

-

"Do nothing.\n"

HQF-6-TUNNEL_POLICY_INST_FAILED

6-Information

\nHQF-TUN: [chars] move failed to [chars] suspending policy

-

qos

"The service-policy will be automatically restored " "if the tunnel adjacency changes again. " "Run 'show policy-map interface <tunnel>' " "to see if the service policy is still suspended. " "If a service-policy remains suspended longer than expected " "then check for other messages in the log that may " "clarify the source of the problem " "e.g. insufficient bandwidth to meet bandwidth guarantees. "

HQF-3-OH_FRAG_NOT_ALLOWED_TOGETHER

3-Error

Can't configure Overhead Accounting and fragmentation together!

Overhead Accouting feature currently is not allowed to coexist with fragmentation configration.

qos

"Remove either Overhead Accouting or fragmentation\n "

CAC-6-MODIFY

6-Information

CAC is already functioning and configuration of per flow [dec] kbps will restart CAC invalidating CAC status for all flows.

This is a user modification. Active CAC flows will all unadmitted till reneg. After reneg flow admit/un-admit status may vary.

qos

LOG_STD_ACTION

CAC-3-MODIFY_FAIL

3-Error

CAC is enabled and per-flow rate modification results in CAC inconsistency. Remove and reapply CAC action in the class.

This is an issue in CAC. Probable cause: CAC state update fails. Check internal data bases.

qos

LOG_STD_ACTION

CAC-6-QOS_MODIFY

6-Information

CAC is already functioning and a configuration modification will restart CAC invalidating current status for all flows.

This is a user modification. Active CAC flows will all unadmitted till reneg. After reneg flow admit/un-admit status may vary.

qos

LOG_STD_ACTION

CAC-3-QOS_MODIFY_FAIL

3-Error

CAC is already functioning and configuration modification results in CAC inconsistency. Remove and reapply CAC action in the class.

This is an issue in CAC. Probable cause: CAC state update fails. Check internal data bases.

qos

LOG_STD_ACTION

PAC-3-WAVL_INIT_FAIL

3-Error

WAVL initialization for [chars] failed.

This is a system problem. Probable cause: low resources in the system. Free up some memory.

-

LOG_STD_ACTION

PAC-3-LIST_CREATE_FAIL

3-Error

LIST creation for instance failed.

This is a system problem. Probable cause: low resources in the system. Free up some memory.

-

LOG_STD_ACTION

PAC-3-SYNC_ERROR

3-Error

cannot [chars] sync data: [chars] [dec] [dec]

Unable to send sync data on active RP or receive and process sync data on standby RP. QoS policy accounting may not work correctly after switch-over.

qos

LOG_STD_ACTION

MKA-5-SESSION_START

5-Notice

[chars] : [dec] MKA Session started for RxSCI [chars] AuditSessionID [chars]

The IOS Authentication Manager has requested for MKA to begin a new MKA Session for a peer that has successfully authenticated with the RxSCI and Audit Session ID given. MKA will begin initialization and setup by creating a new Virtual Port for the given interface & Virtual Port ID. Also all keying information specific to the MSK and EAP Session ID received will be derived.

mka

"No action required normal operation."

MKA-5-SESSION_SECURED

5-Notice

[chars] : [dec] MKA Session was secured for RxSCI [chars]

MKA was able to secure the MKA Session identified by the Audit Session ID & CKN given with the peer identified by the RxSCI given. SESSION_SECURED happens in a successful response to a SESSION_START from the IOS Authentication Manager only after MACsec Secure Channels and Secure Associations have been installed and enabled for both Rx and Tx.

mka

"No action required normal operation."

MKA-5-CAK_REKEY

5-Notice

[chars] : [dec] MKA Session is beginning a CAK Rekey [chars] for RxSCI [chars]

MKA has received a request to perform a CAK Rekey for the MKA Session identified by the given RxSCI Audit Session ID and CKN. A new key is available either from keychain infra or Authentication manager new MSK & EAP Session ID received from EAP Authentication

mka

"No action required normal operation."

MKA-6-CAK_REKEY_SUCCESS

6-Information

[chars] : [dec] MKA Session CAK rekey is successful for RxSCI [chars]

MKA was able to Rekey the MKA Session identified by the Audit Session ID & CKN given for the peer identified by the RxSCI given successfully. CAK_REKEY_SUCCESS happens in a successful response to a SESSION_REAUTH from the IOS Authentication manager only after the MKA Session has seamlessly switched to a new CAK/SAK after rekeying the CAK & SAK.

mka

"No action required normal operation."

MKA-6-SAK_REKEY

6-Information

[chars] : [dec] MKA Session is beginning a SAK Rekey

MKA has received a request to perform a SAK Rekey for the MKA Session identified by the given RxSCI Audit Session ID and CKN. The current Latest Association Number AN and Key Number KN correspond to the

mka

"No action required normal operation."

MKA-4-SAK_TRANSMIT

4-Warning

[chars] : [dec] Installing new TxSA AN [dec] but not all peers have

For a Pairwise CA i.e. one peer MKA acting as the Key Server has distributed a SAK for use in MACsec to a peer with the minimum required MACsec Capability but has not received a SAK-Use payload back from the peer indicating that the peer is receiving using the newly distributed SAK withing 6 seconds MKA Life Time so MKA will go

mka

"Check connection to peers & for any MKPDU " "Validation errors. Also check the MKA/MACsec " "implementation on the peers' systems."

MKA-6-SAK_REKEY_SUCCESS

6-Information

[chars] : [dec] MKA Session successfully completed a SAK Rekey

MKA has successfully performed a SAK Rekey for the MKA Session identified by the given RxSCI Audit Session ID and CKN. The new Latest Association Number AN and Key Number KN correspond to the new Rx/Tx

mka

"No action required normal operation."

MKA-5-SESSION_STOP

5-Notice

[chars] : [dec] MKA Session stopped by [chars] for RxSCI [chars] AuditSessionID [chars]

After being secured the MKA Session identified by the RxSCI Audit Session ID and CKN given was ended or terminated. Possible reasons include using the `clear auth sess` or `clear mka {all | sess}` command keepalive timeout reauth failure or other internal failure.

mka

"If the MKA Session was not supposed to terminate " "check the command history or other system logs " "to find out the specific termination reason. " "`debug mka trace` and `debug mka error` may help " "diagnose the problem if the MKA Session was not " "supposed to terminate. Otherwise no action " "required normal operation."

MKA-4-SESSION_UNSECURED

4-Warning

[chars] : [dec] MKA Session was stopped by [chars] and not secured for RxSCI [chars]

The MKA Session identified by the RxSCI Audit Session ID and CKN given was unable to be secured before being terminated. Possible reasons include no MACsec support on the specified interface invalid MACsec configuration for the specified interface the peer identified by the given RxSCI not having enough MACsec Capability or other internal failure prior to the establishment of Rx/Tx Secure Channels and installation of Rx/Tx Secure Associations in MACsec. MKA will report back to the IOS Authentication Manager that it was unable to secure the session to indicate either Authz Failed for a LinkSec policy of `must-secure` or to be hosted unsecured for a LinkSec policy of `should-secure`.

mka

"If the MKA Session should have been secured check " "for other MKA system logs that indicate the reason " "for not being secured. Check MACsec support on " "the interface & peer MACsec configuration and " "connectivity. `debug mka trace` and " "`debug mka error` may help to diagnose the " "problem."

MKA-4-KEEPALIVE_TIMEOUT

4-Warning

[chars] : [dec] Peer has stopped sending MKPDUs for RxSCI [chars]

For a Pairwise CA i.e. one peer MKA has not received a MKPDU from its Live Peer for at least 6 seconds so the MKA Session will be terminated. If this is a Group CA i.e. multilple peers MKA has not received a MKPDU from

mka

"Check connection to peer and if peer is still up " "and responding. Also check for MKPDU Validation " "Failures."

MKA-4-MKA_MACSEC_CIPHER_MISMATCH

4-Warning

[chars] : [dec] Lower strength MKA-cipher than macsec-cipher for RxSCI [chars]

Higher strength Macsec Cipher is configured than the MKA cipher. This is not recommended from a security purpose.

mka

"Review the MKA cipher config and the macsec cipher " "config and ensure that the MKA cipher is either of " "the same or higher strength than macsec cipher"

MKA-4-INVALID_MACSEC_CAPABILITY

4-Warning

[chars] : [dec] Terminating MKA Session because no peers had the

MKA Session was terminated because no peers in the CA had a high enough MACsec Capability value set in MKPDUs received to use SAKs distributed by this Key Server. The required minimum MACsec Capability is dictated by the configured MACsec options.

mka

"Check the MACsec Capability of the peers' hardware " "or lower the requirements for MACsec Capability by " "changing the MACsec configuration for this " "interface."

MKA-3-CAK_DERIVE_FAILURE

3-Error

[chars] : [dec] Unable to derive CAK for RxSCI [chars] AuditSessionID [chars]

Internal failure - MKA failed to derive the Connectivity Association Key CAK from the received MSK through EAP

mka

"`debug mka trace` and `debug mka error` may help " "to diagnose the problem internal failure."

MKA-3-CKN_DERIVE_FAILURE

3-Error

[chars] : [dec] Unable to derive CKN for RxSCI [chars] AuditSessionID [chars]

Internal failure - MKA failed to derive the Connectivity Association Key Name CKN from the received EAP

mka

"`debug mka trace` and `debug mka error` may help " "to diagnose the problem internal failure."

MKA-3-ICK_DERIVE_FAILURE

3-Error

[chars] : [dec] Unable to derive ICK for RxSCI [chars] AuditSessionID [chars]

Internal failure - MKA failed to derive the Integrity Check Value ICV Key ICK from the derived CAK & CKN

mka

"`debug mka trace` and `debug mka error` may help " "to diagnose the problem internal failure."

MKA-3-KEK_DERIVE_FAILURE

3-Error

[chars] : [dec] Unable to derive KEK for RxSCI [chars] AuditSessionID [chars]

Internal failure - MKA failed to derive the Key Encrypting Key KEK from the derived CAK & CKN

mka

"`debug mka trace` and `debug mka error` may help " "to diagnose the problem internal failure."

MKA-3-SAK_GENERATE_FAILURE

3-Error

[chars] : [dec] Unable to generate SAK AN [dec] KN [dec] for RxSCI [chars]

Internal failure - MKA failed to generate the Secure Association Key SAK from the derived CAK & given Key

mka

"`debug mka trace` and `debug mka error` may help " "to diagnose the problem internal failure."

MKA-3-HASH_KEY_GENERATE_FAILURE

3-Error

[chars] : [dec] Unable to generate MACsec Hash Key AN [dec] for RxSCI [chars]

Internal failure - MKA failed to generate the MACsec Hash Key for the MKA Session with the given RxSCI Audit Session ID and CKN. The Hash Key is used by MACsec to authenticate frames i.e. provide integrity checking support and is installed in the Rx/Tx

mka

"`debug mka trace` and `debug mka error` may help " "to diagnose the problem internal failure."

MKA-3-SAK_CIPHER_MISMATCH

3-Error

[chars] : [dec] Received [chars] cipher it is not configured

The received cipher is not configured or supported

mka

"If received cipher is supported change configuration " "at receive side or change cipher at KS to include " "the supported cipher"

MKA-3-MKPDU_VALIDATE_FAILURE

3-Error

[chars] : [dec] Validation of a MKPDU failed for RxSCI [chars]

A MKPDU received for the MKA Session identified by the give RxSCI Audit Session ID and CKN failed one or more of the follwoing validation checks:\n - MKPDU Integrity\n - Packet length reported equals actual packet length\n - Valid CKN Algorithm Agility\n - ICV Verification\n - Correct paramset order & existence of MKA payloads\n - MI verification if peers exist\n - MN verification if peers exist.

mka

"`debug mka { packet | trace | error }` may help to " "diagnose the problem. Also any packet traces and " "captures may help too internal failure."

MKA-3-MKPDU_ICV_VERIFICATION_FAILURE

3-Error

[chars] : [dec] ICV Verification of a MKPDU failed for RxSCI [chars]

The ICV Verification failed of MKPDU received for the MKA Session Identified by the given RxSCI Audit Session ID and CKN failed. The reason for the same could be the following: - The CAK is misconfigured on the RxSCI in case of PSK\n - The MKPDU data is tampered during transmission.

mka

"Check the configured CAK on RxSCI" "To validate MKPDU data tampering `debug mka " "{ packet }` at both side may help to diagnose " "the problem."

MKA-3-INVALID_CA

3-Error

CA entry not found while [chars].

MKA was unable to find the CA entry during the indicated action. This is an internal error.

mka

"Provide the traceback and if possible " "`debug mka trace` and `debug mka error` output " "internal error."

MKA-3-INVALID_VP

3-Error

VP entry not found while [chars].

MKA was unable to find the VP entry during the indicated action. This is an internal error.

mka

"Provide the traceback and if possible " "`debug mka trace` and `debug mka error` output " "internal error."

MKA-3-INVALID_SESSION

3-Error

MKA Session entry not found while [chars].

MKA was unable to find the MKA Session entry during the indicated action. This is an internal error.

mka

"Provide the traceback and if possible " "`debug mka trace` and `debug mka error` output " "internal error."

MKA-3-INTERNAL_ERR

3-Error

[chars] : [dec] Internal MKA Error - failed to [chars] for RxSCI [chars]

The MKA Session identified by the given RxSCI Audit Session ID and CKN encountered an internal error specified by the given action.

mka

"Provide the traceback and if possible " "`debug mka trace` and `debug mka error` output " "internal error."

MKA-3-INVALID_CAK

3-Error

[chars] : [dec] CAK was invalid while [chars] for RxSCI [chars]

The MKA Session identified by the given RxSCI Audit Session ID and CKN failed to perform the indicated action because of an invalid CAK i.e. zero CAK.

mka

"Provide the traceback and if possible " "`debug mka trace` and `debug mka error` output " "internal error."

MKA-3-INVALID_CKN

3-Error

[chars] : [dec] CKN was invalid while [chars] for RxSCI [chars]

The MKA Session identified by the given RxSCI and Audit Session ID failed to perform the indicated action because of an invalid CKN i.e. zero CKN.

mka

"Provide the traceback and if possible " "`debug mka trace` and `debug mka error` output " "internal error."

MKA-3-INVALID_BASIC_PARAM_SET

3-Error

[chars] : [dec] Basic Paramter Set was invalid in a MKPDU for

MKA failed to process the Basic Parameter Set of a received MKPDU.

mka

"No action required internal error."

MKA-3-INVALID_PEER_LIST_PARAM_SET

3-Error

[chars] : [dec] Peer List Paramter Set was invalid in a MKPDU for

MKA failed to process the SAK-Use Parameter Set of a received MKPDU.

mka

"No action required internal error."

MKA-3-INVALID_SAK_USE_PARAM_SET

3-Error

[chars] : [dec] SAK-Use Paramter Set was invalid in a MKPDU for

MKA failed to process the SAK-Use Parameter Set of a received MKPDU.

mka

"No action required internal error."

MKA-3-INVALID_DIST_SAK_PARAM_SET

3-Error

[chars] : [dec] Distributed SAK Paramter Set was invalid in a MKPDU

MKA failed to process the Distributed SAK Parameter Set of a received MKPDU.

mka

"No action required internal error."

MKA-3-INVALID_ANNOUNCEMENT_PARAM_SET

3-Error

[chars] : [dec] Announcement Paramter Set was invalid in a MKPDU for

MKA failed to process the Announcement Parameter Set of a received MKPDU.

mka

"No action required internal error."

MKA-3-INVALID_PARAM_SET

3-Error

[chars] : [dec] Unknown Parameter Set in a MKPDU for RxSCI [chars]

MKA Session failed to process an Unknown Parameter Set of a received MKPDU.

mka

"No action required internal error."

MKA-3-DUPLICATE_AUTH_MGR_HANDLE

3-Error

[chars] Received a new SESSION_START request with Auth-Mgr Handle

MKA received a SESSION_START request from the IOS Authentication Manager Auth-Mgr with an Auth-Mgr Handle

mka

"File a defect for the dot1x-ios component."

MKA-3-UNEXPECTED_HA_MESSAGE

3-Error

Received unexpected message during MKA HA process

Undefined message event encountered.

mka

"No action required internal error."

AN-4-DEVICE_NOT_IN_WHITELIST

4-Warning

Device with UDI [chars]

The autonomic network registration authority will not allow this device to join as it is not in whitelist

AN

LOG_STD_NO_ACTION

AN-4-DEVICE_ALREADY_REGISTERED_BY_ANR

4-Warning

Device with UDI [chars] connected to Proxy Addr [chars] on interface [chars] is already registered by

The autonomic network registration authority will not allow this device to join as it already registered with a different public key

AN

LOG_STD_NO_ACTION

AN-6-DEVICE_ALLOWED_BY_ANR

6-Information

Device with udi [chars] is allowed by autonomic registrar in its Domain ID [chars] with addr [chars] and Device ID [chars]

The autonomic network registration authority has authorised this device to enter its network

AN

LOG_STD_NO_ACTION

AN-6-DEVICE_ENROLLED

6-Information

Device with UDI [chars] connected to Proxy Addr [chars] on the interface [chars] is allowed by Autonomic registrar Addr [chars]

The autonomic network registration authority has enrolled this device

AN

LOG_STD_NO_ACTION

AN-5-DEVICE_BOOTSTRAPPED_BY_ANR

5-Notice

Device with UDI [chars] and Addr [chars] has been boot strapped by autonomic registrar in autonomic domain [chars]

The autonomic network registration authority has bootstrapped this device

AN

LOG_STD_NO_ACTION

AN-5-ANR_UP

5-Notice

A New Autonomic Registrar has been configured in domain [chars] and it has been assigned IP Addr [chars]

The autonomic network registration authority has been confgiured and is locally up

AN

LOG_STD_NO_ACTION

AN-5-ANR_DOWN

5-Notice

Disabled autonomic registrar with Addr [chars]

The autonomic network registration authority functionality is disabled

AN

LOG_STD_NO_ACTION

AN-4-MASA_AUTH_FAIL

4-Warning

Device with udi [chars] is not authorized by MASA

The MASA - manufacturer authorised signing authority has not authorised this device in its network

AN

LOG_STD_NO_ACTION

AN-4-MASA_AUDIT_LOG_FAIL

4-Warning

Device with udi [chars] is not in the audit log of MASA

The manufacturer authorised signing authority audit log doesnt contain this device in its database

AN

LOG_STD_NO_ACTION

AN-6-MASA_NOT_CONFIG

6-Information

Autonomic registrar with udi [chars] has no reachability to MASA -not configured Cant verify device udi [chars]

The manufacturer authorised signing authority has not been configured cannot do the verification of device

AN

LOG_STD_NO_ACTION

AN-6-ANR_WHITELIST_CONFIG

6-Information

Autonomic registrar with Addr [chars] Domain id [chars] has whitelist- will allow only these devices in autonomic network

The autonomic registeration authority has been configured with white list and will allow only these devices to enter its network

AN

LOG_STD_NO_ACTION

AN-6-ANR_WHITELIST_NOT_CONFIG

6-Information

Autonomic registrar with Addr [chars] has no whitelist- will allow all devices

The autonomic registeration authority has not been configured with white list and will allow all devices to enter its network

AN

LOG_STD_NO_ACTION

AN-3-ANR_WHITELIST_FILE_ERROR

3-Error

Autonomic Registrar with Addr [chars] encountered error in

The autonomic registeration authority encountered file error when reading from whitelist file check the file name and its contents

AN

LOG_STD_NO_ACTION

AN-3-IDP_INTENT_FILE_ERROR

3-Error

Device Addr [chars] encountered error [chars] when reading from

The Intent Distribution Protocol Module encountered file error when reading from intent file check the file name and its contents

AN

LOG_STD_NO_ACTION

AN-5-IDP_INTENT_VER_UPDATED

5-Notice

Device Addr [chars] updated to a new Intent version [dec]

The device received a new intent file by Intent Distribution Protocol

AN

LOG_STD_NO_ACTION

AN-5-IDP_INTENT_VER_OLD_DISCARD

5-Notice

Device Addr [chars] discarded the older intent version [dec]

The device received an old intent file by Intent Distribution Protocol and is discarding it

AN

LOG_STD_NO_ACTION

AN-5-SERVICE_LEARNT

5-Notice

Device with Addr [chars] learnt Autonomic service with Service Type [dec] Service IP Addr [chars]

-

-

-

AN-6-UDI_AVAILABLE

6-Information

UDI - [chars]

Unique device identification number is available on the device

AN

LOG_STD_NO_ACTION

AN-6-AN_ABORTED_BY_CONSOLE_INPUT

6-Information

Autonomic disabled due to User intervention on console. configure 'autonomic' to enable it.

User entered into configuration mode So AN is disabled An process is stopped

AN

LOG_STD_NO_ACTION

AN-6-AN_ABORTED_BY_NO_AUTONOMIC

6-Information

Autonomic disabled due to 'no autonomic' command.

'No autonomic' command is entered So AN is disabled An process is stopped

AN

LOG_STD_NO_ACTION

AN-6-AN_ABORTED_BY_MANUAL_CONFIG_DETECTED

6-Information

Autonomic disabled due to detection of new configuration.

Some other process configures something. So AN is disabled An process is stopped

AN

LOG_STD_NO_ACTION

AN-6-CONFIG_SAVE

6-Information

Issuing 'write memory' to save config

Saving configurations to startup-config by AN process

AN

LOG_STD_NO_ACTION

AN-6-SUDI_AVAILABLE

6-Information

secure UDI - [chars]

Secure unique device identification number is available on the device

AN

LOG_STD_NO_ACTION

AN-5-NBR_IN_DOMAIN

5-Notice

Neighbor with Addr [chars] connected via interface [chars] to device Addr [chars] is brought inside my domain [chars]

The device has been admitted into the autonomic domain

AN

LOG_STD_NO_ACTION

AN-5-NBR_OUT_DOMAIN

5-Notice

Neighbor with Addr [chars] connected via interface [chars]

The device is removed from the autonomic domain it can happen if the domain certificate is NULL or if the domain certificate is invalid

AN

LOG_STD_NO_ACTION

AN-5-NBR_ADDED

5-Notice

Device with UDI [chars] is added as a Neighbor to Device with Addr [chars] on the interface [chars]

A hello message is received and the device is added in the neighbor table

AN

LOG_STD_NO_ACTION

AN-5-NBR_LOST

5-Notice

Device with ACP Addr [chars] lost connectivity to its Neighbor Addr [chars] on interface [chars]

Lost connectivity to the neighboring device & it is no longer part of autonomic domain

AN

LOG_STD_NO_ACTION

AN-6-NBR_DOMAIN_CERT_VALID

6-Information

Domain certificate of Neighbor with Addr [chars]

The domain certificate of the neighbor device is validated successfully

AN

LOG_STD_NO_ACTION

AN-3-NBR_DOMAIN_CERT_INVALID

3-Error

Domain certificate of Neighbor with Addr [chars] connected on interface [chars] is invalid

The domain certificate of the neighbor device is invalid

AN

LOG_STD_NO_ACTION

AN-3-NBR_DOMAIN_CERT_REVOKED

3-Error

Domain certificate of Neighbor with Addr [chars] connected on interface [chars] is revoked

The domain certificate of the neighbor device has been revoked

AN

LOG_STD_NO_ACTION

AN-3-NBR_DOMAIN_CERT_EXPIRED

3-Error

Domain certificate of Neighbor with Addr [chars] connected on interface [chars] has expired

The domain certificate of the neighbor device has expired

AN

LOG_STD_NO_ACTION

AN-6-MY_DOMAIN_CERT_RENEWED

6-Information

Domain certificate of device Addr [chars] has been renewed

The domain certificate of this device is renewed

AN

LOG_STD_NO_ACTION

AN-6-MY_DOMAIN_CERT_EXPIRED

6-Information

Domain certificate of this device Addr [chars] has expired

The domain certificate of this device has expired

AN

LOG_STD_NO_ACTION

AN-3-DOMAIN_KEY_GEN_FAIL

3-Error

The bootstrapping device with key label [chars]

The key pair generation failed at the device for triggering BS request message to Autonomic registrar. Can be due to failure in RSA key pair generation in the crypto library

AN

LOG_STD_NO_ACTION

AN-4-ANR_SIGN_VERIFY_FAIL

4-Warning

Device UDI [chars] signature verification of Autonomic registrar

The new device joining the network verified the signature of autonomic registrar as a part of mutual authentication and the verification failed

AN

LOG_STD_NO_ACTION

AN-4-MASA_AUTH_TOKEN_PARSE_ERROR

4-Warning

Error while parsing authentication token from MASA server for device udi-[chars]

Encountered error while parsing the authentication token response string from MASA server

AN

LOG_STD_NO_ACTION

AN-3-TLV_PARSE_ALIGN_ERROR

3-Error

TLV parsed Len [dec] Next TLV could be misaligned

Parsed TLV message is not a multiple of 4 and the next TLV message can be misaligned

AN

LOG_STD_NO_ACTION

AN-3-TLV_PARSE_LEN_INCORRECT

3-Error

TLV parsed len [dec] > original message length [dec]

Parsed TLV message length is greater than original message length

AN

LOG_STD_NO_ACTION

AN-3-MSG_INVALID_HEADER

3-Error

Invalid message header type [dec] received

The message packet header got corrupted and invalid header received

AN

LOG_STD_NO_ACTION

AN-6-ACP_ROUTING_GLOBAL_ENABLED

6-Information

Enabled global OSPFv3 pid [dec]rid [inet]area [dec]

OSPF routing has been enabled globally

AN

LOG_STD_NO_ACTION

AN-6-ACP_ROUTING_INTERFACE_ENABLED

6-Information

OSPF routing enabled on interface: [chars] pid [dec]rid [inet] area [dec]

OSPF routing has been enabled on all physical interface

AN

LOG_STD_NO_ACTION

AN-6-ACP_ROUTING_GLOBAL_DISABLE

6-Information

Removed OSPFv3 routing globally pid [dec]

OSPF routing has been disabled globally

AN

LOG_STD_NO_ACTION

AN-6-ACP_VRF_GLOBAL_CREATE_SUCCESS

6-Information

Device UDI [chars] Autonomic VRF

Autonomic network VRF has been created globally

AN

LOG_STD_NO_ACTION

AN-3-ACP_VRF_GLOBAL_CREATE_FAIL

3-Error

Device UDI [chars] failed to create

Autonomic network VRF has not been created globally

AN

LOG_STD_NO_ACTION

AN-6-ACP_VRF_GLOBAL_REMOVE

6-Information

Device UDI [chars] Autonomic VRF

Autonomic network VRF has been removed globally

AN

LOG_STD_NO_ACTION

AN-6-ACP_VRF_INTERFACE_CREATE_SUCCESS

6-Information

Device UDI [chars]

Autonomic network VRF has been created on the interface

AN

LOG_STD_NO_ACTION

AN-3-ACP_VRF_INTERFACE_CREATE_FAIL

3-Error

Device UDI [chars] failed to create Autonomic VRF

Autonomic network VRF has not been created on the interface

AN

LOG_STD_NO_ACTION

AN-6-ACP_CHANNEL_TO_NBR_CREATED

6-Information

Established ACP [chars] from Device Addr [chars] to

Autonomic Network Control plane Channel has been created to the neighbor

AN

LOG_STD_NO_ACTION

AN-3-ACP_CHANNEL_TO_NBR_FAILED

3-Error

Failed to create ACP [chars] from Device Addr [chars]

Autonomic Network Control Plane Channel has not been created to the neighbor

AN

LOG_STD_NO_ACTION

AN-6-ACP_CHANNEL_TO_NBR_REMOVED

6-Information

Removed ACP [chars] from Device Addr [chars] to

Autonomic Network Control Plane Channel to neighbor is removed

AN

LOG_STD_NO_ACTION

AN-6-ACP_IPSEC_TO_NBR_CREATED

6-Information

Established IPSEC on ACP from Device Addr [chars]

Autonomic Network Control plane - IPSEC tunnel established to neighbor

AN

LOG_STD_NO_ACTION

AN-3-ACP_IPSEC_TO_NBR_FAILED

3-Error

Failed to create IPSEC on ACP from device Addr [chars]

Autonomic Network Control plane - Failed to create IPSEC tunnel to neighbor

AN

LOG_STD_NO_ACTION

AN-6-ACP_IPSEC_TO_NBR_REMOVED

6-Information

Removed IPSEC on ACP from Device Addr [chars] to

Autonomic Network Control plane - IPSEC tunnel to neighbor is removed

AN

LOG_STD_NO_ACTION

AN-6-ACP_DIKE_TO_NBR_CREATED

6-Information

Established DIKE on ACP [chars] from Device Addr [chars]

Autonomic Network Control plane - DIKE tunnel established to neighbor

AN

LOG_STD_NO_ACTION

AN-3-ACP_DIKE_TO_NBR_FAILED

3-Error

Failed to create DIKE on ACP [chars] from Device Addr [chars]

Autonomic Network Control plane - Failed to create DIKE tunnel to neighbor

AN

LOG_STD_NO_ACTION

AN-6-ACP_DIKE_TO_NBR_REMOVED

6-Information

Removed DIKE on ACP [chars] from Device Addr [chars]

Autonomic Network Control plane - DIKE tunnel to neighbor is removed

AN

LOG_STD_NO_ACTION

AN-6-CONFIG_DOWNLOAD_SUCCESS

6-Information

Config download at the Device Addr [chars]

Download of the config file to the Running config is Successful

AN

LOG_STD_NO_ACTION

AN-6-CONFIG_DOWNLOAD_FAILED

6-Information

Config download on the Device Addr [chars] has FAILED

Failed to download the config file to the Running config

AN

LOG_STD_NO_ACTION

AN-6-CONFIG_DOWNLOAD_STARTED

6-Information

Config download started on the Device Addr [chars]

Config download is triggerred

AN

LOG_STD_NO_ACTION

AN-5-CD_STATE_CHANGED

5-Notice

[chars] Channel [dec] [chars] - Our Intf [chars]

CD L2 or Reuse Channel Created/Removed/Expired

AN

LOG_STD_NO_ACTION

CFT_API-3-CFT_ERRMSG_NO_MEMORY

3-Error

[chars] [chars] [dec]

The system was unable to supply the requested memory for flow processing to continue.

common-flow-table

-

CFT_API-3-CFT_ERRMSG_MAX_MEMORY

3-Error

[chars] [chars] [dec]

The maximum number of concurrent flows allowed has been exceeded. Some flows might not received the provisioned level of service.

common-flow-table

"This is the platform limit. Either lower the network load on this device " "or upgrade to a higher capacity platform." LOG_STD_SH_TECH_ACTION

CFT_API-4-CFT_ERRMSG_CLIENT_PRE_CREATE_PREVENTED

4-Warning

[chars] [chars] [dec]

Flow creation was prevented by a flow table client. This may be due to an explicit policy that is enabled.

common-flow-table

"Check your policies to ensure this what you intend." LOG_STD_SH_TECH_ACTION

CFT_API-4-CFT_ERRMSG_FLOW_CREATION_PREVENTED

4-Warning

[chars] [chars] [dec]

Flow creation was denied by a the system. A possible denial of service attack may have been detected.

common-flow-table

"Modify your denial of service policy if this is in error." LOG_STD_SH_TECH_ACTION

CFT_API-5-CFT_ERRMSG_UNSUPPORTED_L3_PROTOCOL

5-Notice

[chars] [chars] [dec]

An unsupported layer 3 protocol was identified.

common-flow-table

"Flow based inspection does not support this protocol at this time." LOG_STD_SH_TECH_ACTION

CFT_API-5-CFT_ERRMSG_NON_FIRST_IP_FRAGMENT

5-Notice

[chars] [chars] [dec]

The flow table was unable to process a TCP fragmented packet. Service for these packets may be unavailable.

common-flow-table

"Enable the virtual fragment reassembly VFR functionality."

CFT_API-7-CFT_ERRMSG_CLIENT_API

7-Debug

[chars] [chars] [dec]

A CFT client may have a incorrectly accessed an API.

common-flow-table

"This is an internal software error. Please report it to your technical " "support representative." LOG_STD_SH_TECH_ACTION

CFT_API-3-CFT_ERRMSG_UNKNOWN

3-Error

[chars] [chars] [dec]

The error message type does not match the possible enumerated definitions.

common-flow-table

"This is an internal software error. Please report it to your technical " "support representative." LOG_STD_SH_TECH_ACTION

TFTP-7-GLEAN_DISABLED

7-Debug

ARP gleaning from TFTP has been disabled.

The ARP gleaning from TFTP has been disabled.

-

"If you want ARP gleaning from TFTP do ip arp gleaning tftp."

NTP-6-RESTART

6-Information

NTP process starts

NTP process has just started or re-started.

-

LOG_STD_NO_ACTION

NTP-6-STOP

6-Information

NTP process stops

NTP is disabled.

-

"Check if NTP is disabled by administrator purposely."

NTP-4-UNSYNC

4-Warning

NTP sync is lost

NTP synchronization to its peer is lost.

-

"Check network connection to the peer if NTP is running on the peer\n\ if the peer itself is synchronized to a stable time source and if NTP\n\ packets from the peer have passed validity tests specified in the\n\ RFC1305 etc."

NTP-4-PEERUNREACH

4-Warning

Peer [inet] is unreachable

The NTP peer is unreachable.

-

"Check network connection to the peer and if NTP is running on the peer."

NTP-6-PEERREACH

6-Information

Peer [inet] is reachable

The NTP peer is reachable.

-

LOG_STD_NO_ACTION

NTP-5-PEERSYNC

5-Notice

NTP synced to peer [inet]

NTP has synchronized the local clock to a new peer.

-

LOG_STD_NO_ACTION

NTP-4-V6DISABLED

4-Warning

IPv6 is not running on interface [chars]. Cannot send NTP message.

This informational message logs availability transitions in the Service Assurance Agent probes. This messages appears when the <CmdBold>ip sla logging trap<NoCmdBold> command is entered

rsps-time-rptr

"If this message is not necessary enter the " "<CmdBold>no ip sla logging trap<NoCmdBold> command to disable " "logging. Otherwise no action is required"

IAMP-4-CLIENT_ID_EXIST

4-Warning

Client id [[dec]] already exists

client id already exists in the database. Choose unique ID to solve this issue

mediatrace

"Applications could be re-registering or client id is in use by " "other application. If it is not due to duplicate registration " "it may be advisable to contact your Cisco technical support " "representative."

IAMP-4-CLIENT_REG_FAILED

4-Warning

Client id [[dec]] could not be registered

Error occured while registering the client.

mediatrace

"Collect show memory summary and contact your Cisco " "technical support representative."

MEDIATRACE-3-R_REQ_DUPLICATED_GSID

3-Error

Request with duplicated global session id [dec] was detected from

There should not be 2 concurrent sessions with identical global session id from the same Initiator node. If found it's an error condition.

mediatrace

"To help resolve this error condition capture the " "output of `show run all | sec mediatrace' and send it to " "Cisco Technical Support."

MEDIATRACE-3-R_REQ_DROPPED_QMAXED

3-Error

Request with global session id [dec] was dropped because

The maximum number of Responder sessions has been exceeded and there is no more sessions available for new periodical requests. This request was dropped.

mediatrace

"Assess the router resource to see if it can take on more " "sessions as more sessions can take away some CPU and memory from " "the system. If it's OK to increase the max sessions for the " "local node then use the `mediatrace responder max-sessions' CLI " "to increase the local Responder's max sessioins. As a good practice " "keep session life cycle shorter so to share the sessions."

MEDIATRACE-3-R_SESS_FORCED_REMOVAL

3-Error

User issued a forced shutdown. All Mediatrace Responder sessions are removed.

Only user can issue the `no mediatrace responder force' CLI. This is a non-graceful shutdown of Mediatrace sessions. All sessions are purged when this message is seen.

mediatrace

"Only when some inconsistency in session count is observed between " "Mediatrace Responder and VM or when the local node is under " "stress and need to remove all Mediatrace sessions."

MEDIATRACE-4-R_RC_INTF_EVENT

4-Warning

IAMP event [chars] is received for [chars].

When RSVP-TP layer detects a route change or interface change for the local node IAMP relays the notice as IAMP_EVENT_TYPE_RC_LOCAL or IAMP_EVENT_TYPE_IF_CHANGE notice to Responder. Responder will search all impacted sessions to stop and re-start the monitoring.

mediatrace

"Do nothing. This message is emitted when detecting a rare RSVP " "product behavior. Mediatrace is designed to handle this notice."

MEDIATRACE-3-R_DELIVERY_FAILED

3-Error

Response delivery to target IP [chars] failed for global

This message is seen when IAMP or RSVP reported problem in sending response for Responder.

mediatrace

"Turn on 'debug iamp error' to see more details on what IAMP layer is " "complaining."

MEDIATRACE-4-R_EMPTY_REQ

4-Warning

request has empty payload.

For unknown reason a request is received with empty payload.

mediatrace

"Do nothing. This is a very rare but harmless event."

MEDIATRACE-5-R_SESS_DOWN

5-Notice

Responder received a SESSION_DOWN event for [chars]

When Initiator removes a configured session via IAMP it informs RSVP to tear down the session object and hence SESSION_DOWN notice is propagated down the path to all Responders.

mediatrace

"Do nothing. This is part of normal behavior."

MEDIATRACE-3-R_SESS_SERVL_ALLOC_FAILED

3-Error

memory allocation of servlet object failed for global session id [dec]

Before a request can be processed a servlet memory object needs to be allocated first. This message reports that such memory allocation failed because the system is momentarily short of memory.

mediatrace

"Check system memory situation and do minor tunings at various " "feature CLIs so to reduce memory demand level."

MEDIATRACE-3-R_SESS_ALLOC_FAILED

3-Error

memory allocation of session object failed for [chars] for

Before a request can be processed a session object needs to be allocated first. This message reports that such malloc failed due to the system is momentarily short of memory.

mediatrace

"Check system memory situation and do minor tunings at various " "feature CLIs so to reduce memory demand level."

MEDIATRACE-6-R_SESS_PERIODICAL_CREATE_SUCCESS

6-Information

New periodical session with global session id [dec] is added.

This message is produced when a new periodical session is configured for a new request with specified global session id.

mediatrace

"Do nothing."

MEDIATRACE-6-R_SESS_TRANSIENT_REMOVE_SUCCESS

6-Information

A transient session of [chars] with global session id [dec] successfully

This is an informational syslog message for reporting that an one-shot transient request sessions is successfully removed.

mediatrace

"Do nothing."

MEDIATRACE-3-R_SESS_REMOVE_FAILED

3-Error

failed to remove a session with global session id [dec] from queue

This message indicates that there is a problem in removing the concerned session from the session queue. This is very rare.

mediatrace

"Do nothing. If this message is seen more than once then user can " "`no mediatrace responder force' CLI to purge the session queue."

MEDIATRACE-6-R_SESS_REMOVE_ALL_DVMC_SESSIONS

6-Information

No more active sessions at the moment. DVMC API was called to purge all Mediatrace sessions.

This is only an informational message. This message is produced after informing DVMC that there is no more active sessions in Mediatrace Responder.

mediatrace

"Do nothing."

MEDIATRACE-4-R_RC_INTF_DAMPENING

4-Warning

Dampening IAMP event [chars] received for global session id [dec].

To prevent path flip flop and cause unnecessary stop and re-start on monitoring objects any same subsequent route change or interface change event is subject to a dampening timer before required actions are taken by Responder for the impacted sessions. During the dampening window same kind of event notice will be ignored.

mediatrace

"Start from using RSVP related CLI to troubleshoot why flip flop on " "a route is happening."

MEDIATRACE-3-R_SNMP_COMM_STR_MISSING

3-Error

'snmp-server community public ro' is not configured or access is denied. session id [dec].

Some Mediatrace Initiator has sent System Data requests to this node but the snmp get requests have failed because the running config is missing the CLI 'snmp-server community public ro' or there is additional config blocking read access.

mediatrace

"Configure a snmp server community to allow requests using 'snmp-server " "community public RO' command or check no other configuration is blocking " "SNMP reads."

MEDIATRACE-3-I_PROFILE_DB

3-Error

Operation failure in profile DB

Profile DB operation failed.

mediatrace

"Contact your Cisco technical support " "representative."

MEDIATRACE-3-I_INFRA

3-Error

Initiator Error: [chars]

An internal error in initiator event processing has occurred.

mediatrace

"This may be a transient error condition. If the " "problem persists contact your Cisco technical " "support representative."

MEDIATRACE-3-I_SES_IAMP

3-Error

session = [dec]: reason = [chars]

An error occurred while Mediatrace application was trying to initiate a session send a data fetch request or terminate the session.

mediatrace

"Contact your Cisco technical support " "representative."

MEDIATRACE-3-I_SES_SOFT

3-Error

session = [dec]: reason = [chars]

Session failure due to some Mediatrace internal software error.

mediatrace

"Contact your Cisco technical support " "representative."

MEDIATRACE-6-I_SES_EVENT

6-Information

session = [dec]: ignored event: [dec]

This is informational. The ignored event number is printed.

mediatrace

"Do nothing."

MEDIATRACE-4-I_SES_RESTART

4-Warning

session = [dec]: [chars]

A condition affecting normal Mediatrace session operation detected. Session needs to be restarted.

mediatrace

"Reschedule the session identified by giving " "no mediatrace schedule command followed by " "mediatrace schedule command."

MEDIATRACE-5-I_SES_START

5-Notice

Local-ID = [dec] Global-ID = [dec] [chars]

A new mediatrace session is scheduled.

mediatrace

"This is notification of Mediatrace session start " "no action is required."

RTT-4-DuplicateEvent

4-Warning

IP SLAs [dec]: Duplicate event received. Event number [dec]

IP SLAs process has received a duplicate event

rsps-time-rptr

"This is only a warning message. If this recurs " "enter the command <CmdBold>show ip sla configuration<NoCmdBld> and " "copy the output of the command. Copy the message as it appears on " "the console or in the system log contact your Cisco technical " "support representative and provide the representative with the " "gathered information along with information about the application " "that is configuring and polling the Service Assurance Agent probes."

RTT-3-IPSLANOPROCESS

3-Error

IP SLAs: Cannot create a new process

IP SLAs is unable to start a new process and may not be running.

rsps-time-rptr

LOG_STD_REDUCE_ACTION

RTT-3-IPSLANEGATIVEVALUE

3-Error

IP SLAs[dec]: Negative Value for [chars]

IP SLAs statistics has generated an error message.

rsps-time-rptr

"Contact your Cisco technical support " "representative"

RTT-3-IPSLAPROBENOTFOUND

3-Error

IP SLAs: Error deleting the probe

Trying to delete a probe which does not exist

rsps-time-rptr

"Contact your Cisco technical support " "representative"

RTT-3-IPSLATHRESHOLD

3-Error

IP SLAs[dec]: Threshold [chars] for [chars]

This informational message logs threshold violations in the Service Assurance Agent probes. This messages appears when the <CmdBold>ip sla logging trap<NoCmdBold> command is entered

rsps-time-rptr

"If this message is not necessary enter the " "<CmdBold>no ip sla logging trap<NoCmdBold> command to disable " "logging. Otherwise no action is required"

RTT-3-IPSLAINITIALIZEFAIL

3-Error

IP SLAs: Failed to initialize IP SLAs functionality will not work

IP SLAs failed to initialize. This condition is caused by either a timer wheel timer functionality init that failed or a process that could not be created. A likely cause of this condition is that sufficient memory is not available to complete the task.

rsps-time-rptr

"Search for resolved software issues using the Bug " "Toolkit at " "http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl." LOG_STD_REDUCE_ACTION

RTT-3-IPSLATWINITFAIL

3-Error

IP SLAs: Generic Timer wheel timer functionality failed to initialize

IP SLAs could not initialize the timer wheel.

rsps-time-rptr

"Search for resolved software issues using the Bug " "Toolkit at " "http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl." LOG_STD_REDUCE_ACTION

RTT-4-IPSLACLOCKNOTSET

4-Warning

IP SLAs Probes could not be

One or more IP SLAs probes could not be scheduled because system clock is not set.

rsps_time_rptr

"Ensure that the system clock is functional by using Network Time " "Protocol or another mechanism."

RTT-4-IPSLASCHEDCONFIGFAIL

4-Warning

IP SLAs Probe [dec]: [chars]

The IP SLAs probe could not be scheduled. Either the configured starting time has already ocurred or the starting time is invalid.

rsps_time_rptr

"Reschedule the failed probe with a valid start time."

RTT-3-IPSLARESPTWINITFAIL

3-Error

IP SLAs responder initialzation failed

-

-

-

RTT-4-IPSLAENDPOINTDEREGISTER

4-Warning

IP SLAs end point de-registered by hub [inet].

-

-

-

RTT-4-IPSLAAUTODISCOAUTHFAIL

4-Warning

IP SLAs end point discovery authentication failure for spoke [inet].

The IP SLAs responder initialization failed to initialize timerwheel. Because of this failure the IP SLAs probes on other routers for which this router acts as responder will not work.

rsps_time_rptr

"Contact your Cisco technical support representative."

RTT-3-IPSLARESPEVQINITFAIL

3-Error

IP SLAs responder initialzation failed

The IP SLAs responder initialization failed to initialize event queue. Because of this failure the IP SLAs probes on other routers for which this router acts as responder will not work.

rsps_time_rptr

"Contact your Cisco technical support representative."

RTT-3-IPSLARTPAPPINITFAILED

3-Error

IP SLAs rtp operation application process initialzation failed

The IP SLAs rtp operation application process failed to initialize. Because of this failure the IP SLAs rtp operations will not work.

rsps_time_rptr

"Contact your Cisco technical support representative."

RTT-4-SAASCHEDCONFIGFAIL

4-Warning

IP SLA Monitor Probe [dec]: [chars]

The IP SLA Monitor probe could not be scheduled. Either the configured starting time has already ocurred or the starting time is invalid.

rsps_time_rptr

"Reschedule the failed probe with a valid start time."

RTT-4-SAAGRPSCHEDCONFIGFAIL

4-Warning

Group Schedule Entry [dec]: [chars]

The probes could not be group scheduled. Either the configured starting time has already ocurred or the starting time is invalid.

rsps_time_rptr

"Reschedule the group scheduling entry with a valid start time."

RTT-3-SAAMPLS

3-Error

IP SLA Monitor[dec]: MPLS [chars] Probe [chars] [chars] for destination-address

This informational message logs violations in the Service Assurance Agent probes. This messages appears when the <CmdBold>ip sla logging trap<NoCmdBold> command is entered

rsps_time_rptr

"If this message is not necessary enter the " "<CmdBold>no ip sla logging trap<NoCmdBold> command to disable logging. " "Otherwise no action is required"

RTT-3-IPSLA_AQM

3-Error

[chars]: [chars]

This message indicates software error in IPSLA auto qos monitor feature.

rsps_time_rptr

"Contact your Cisco technical support representative."

RTT-4-OPER_TIMEOUT

4-Warning

condition [chars] entry number = [dec]

This message logs timeout condition in the IPSLAs operations. This message is enabled when the <CmdBold>ip sla monitor logging trap<NoCmdBold> command is entered

rsps_time_rptr

"Ensure that the destination for the IPSLAs " "operation is reachable. If you do not want to log these messages for " "IPSLAs operations enter the " "<CmdBold>no ip sla monitor logging trap<NoCmdBold> command to " "disable the logging"

RTT-4-OPER_CLOSS

4-Warning

condition [chars] entry number = [dec]

This message logs connection loss condition in the IPSLAs operations. This message is enabled when the <CmdBold>ip sla monitor logging trap<NoCmdBold> command is entered

rsps_time_rptr

"Ensure the the destination for the IPSLAs " "operation is reachable. Also ensure that the IPSLAs responder " "operation is configured on the destination. If you do not want " "to log these messages for IPSLA operations enter the " "<CmdBold>no ip sla monitor logging trap<NoCmdBold> command to " "disable logging."

RTT-4-AUTOAPI

4-Warning

IPSLAs Auto CFG ERR: [chars][chars] [chars]

An error occured while configuring IPSLAs Auto parameters. Some or all of your configurations may not have been unset

rsps-time-rptr

"Please check the configuration and try again"

RTT-4-AUTOAPIOPER

4-Warning

IPSLAs Auto CFG ERR: [chars][chars][[dec]] [chars]

An error occured while configuring IPSLAs Auto parameters. Some or all of your configurations may not have been unset

rsps-time-rptr

"Please check the configuration and try again"

RTT-3-AUTO

3-Error

Error: [chars]

An error occured while generating IPSLAs Auto operation.

rsps-time-rptr

"Please check the configuration and try again"

RTT-4-AUTOMEM

4-Warning

IPSLAs Auto MEM ERR: [chars][chars] [chars]

IPSLAs Auto feature failed during memory allocation

rsps-time-rptr

"These maybe transient errors please try again"

RTT-4-INVALIDSRCIPADDR

4-Warning

Possible invalid src IP address [inet] configured.

This message appears when no source IP address is found on the host matching the one specified by the user

rsps_time_rptr

"Unconfigure the probe and reconfigure with " "valid source IP address"

RTT-3-REACTNOTIFYFAILED

3-Error

entry number = [dec] reason = [chars]

IPSLAs Reaction condition was met for specified operation and one or more IPSLAs Event Publisher clients have registered interest for this condition but the notification for this occurence failed.

rsps-time-rptr

"These maybe transient system errors and the " "notification may work next time. Use show ip sla" " event-publisher command to see which clients are " " registered and take action recommended by them."

RTT-4-REACTPARTIALEVENT

4-Warning

entry number = [dec] missing data = [chars]

IPSLAs Reaction Event is missing some interesting data

rsps-time-rptr

"This could be because of IPSLAs software error. " "Please collect show ip sla config output and " "report issue to TAC"

RTT-3-EPNOTIFYFAILED

3-Error

event type = [chars] client = [chars] reason = [chars]

Notification for specified type to specified IPSLAs Event Publisher client failed

rsps-time-rptr

"This maybe transient system error and the " "notification may work next time. Take the action " " as suggested by the identified client for loss " " of notification."

RTT-3-EPSTARTERROR

3-Error

Failed to start IPSLAs Event Publisher

IPSLAs is unable to start a new process for Event Publisher. Reaction Alert notifications will not work.

rsps-time-rptr

LOG_STD_REDUCE_ACTION

RTT-3-EPURFTYPE

3-Error

IPSLAs EventPublisher: Unknown reaction filter type for client [chars]

IPSLAs Event Publisher encountered unknown filter type while sending the reaction alert to specified client Reaction Alert notifications may continue to work for same and other clients.

rsps-time-rptr

LOG_STD_REDUCE_ACTION

RTT-4-EPINIT

4-Warning

IPSLAs Event Publisher Init Failed. Reason = [chars]

IPSLAs Event Publisher Initialization failed. The system will try to recover by doing the initialization tasks when first client subscribes to IPSLAs events.

rsps-time-rptr

LOG_STD_REDUCE_ACTION

RTT-4-EPAPI

4-Warning

IPSLAs EP API: [chars] api failed client = [chars] reason = [chars]

IPSLAs Event Publisher API failed for reason identified

rsps-time-rptr

"The error code is reported to API client. Take " "the action recommended by the client identified."

RTT-4-OPER_PROTOERR

4-Warning

Entry number = [dec] Protocol Specific Error [chars] specific code = [dec]

This message logs protocol specific error condition in the IPSLAs operations. This message is enabled when the <CmdBold>ip sla logging traps<NoCmdBold> command is entered

sla

"Ensure that the destination for the IPSLAs " "operation is reachable. Also ensure that the IPSLA responder " "operation is configured on the destination. If you do not want " "to log these messages for IPSLAs operations enter the " "<CmdBold>no ip sla logging traps<NoCmdBold> command to " "disable the logging"

RTT-3-XOS_XDM_ERR

3-Error

IP SLAs: Cannot create a new xdm instance

IP SLAs is unable to start a new xdm instance and may not be running.

sla

"This message indicates that the system is running " "out of xdm instance and the IPSLAs configured after this message " "may fail. So do not configure any probe after this syslog"

RTT-3-IPSLARESP_UDP_PORT_IN_USE

3-Error

IP SLA Responder: udp: [chars] - [dec] Port already in use.

IP SLA Responder is unable to bind the socket as the port specified in the port enable control message is already in use by other application.

sla

"This message indicates that the port configured." "in the udp-jitter operation targetting this Responder is already in use " "and it is recommended to reconfigure the udp operation with a " "different port number."

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

IP SLA Responder: tcp: [chars] - [dec] Port already in use.

IP SLA Responder is unable to bind the socket as the port specified in the port enable control message is already in use by other application.

sla

"This message indicates that the port configured." "in the udp-jitter operation targetting this Responder is already in use " "and it is recommended to reconfigure the tcp operation with a " "different port number."

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

RTT-3-IPSLARESP_TCP_PORT_IN_USE

3-Error

-

-

-

-

ACLMERGE-3-CUDDERROR

3-Error

A CUDD Library error was detected in [chars]

An error was detected by the CUDD Library the ACL-Merge for this invokation has failed. This could result in more traffic being switched by software. The effect of this could be lower performance for the interface for which the merge failed.

aclmerge

"Copy and save this message. Report this to Engineering along with the ACL configuration of this device. Use Topic to search for a similar DDTS. If none found write a DDTS for this problem"

ACLMERGE-3-CUDDWARN

3-Error

A CUDD Library warning message for interest in this event in [chars]

Debug message only. No action required

aclmerge

"Copy and save this message. Report this to Engineering along with the ACL configuration of the device. This is just a debug message of interest to engineering to investigate the case why this happened"

ALARM-3-NOMEM

3-Error

OUT of Memory: [chars]

-

-

""

ALARM-3-CLEAR

3-Error

[chars] [chars] [chars] [chars] [chars]

-

-

""

ALARM-6-ENTITY_INFO

6-Information

[chars] [chars] [chars] [chars] [chars]

Entity alarm assertion or deassertion information.

-

LOG_STD_NO_ACTION

ALARM-6-DEFAULT_ALARM_PROFILE

6-Information

[chars]

Telcordia profile enable or disable information

-

LOG_STD_NO_ACTION

ALARM-3-NOMEM

3-Error

OUT of Memory: [chars]

-

-

""

ALARM-3-CLEAR

3-Error

[chars] [chars] [chars] [chars] [chars]

-

-

""

ALARM-6-ENTITY_INFO

6-Information

[chars] [chars] [chars] [chars] [chars]

Entity alarm assertion or deassertion information.

-

LOG_STD_NO_ACTION

ALG-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

alg

LOG_STD_ACTION

ALG-3-UNINITIALIZED

3-Error

ALG feature is not properly initialized

A function call was made when the system was not properly\n\ initialized.

alg

LOG_STD_ACTION

ALG-3-INIT_FAILED

3-Error

An initialization failed rc[chars]

-

-

-

ALG-3-ENOENT

3-Error

NULL

A lookup failed unexpectedly.

alg

LOG_STD_ACTION

ALG-3-EEXIST

3-Error

NULL

An item unexpectedly exists already.

alg

LOG_STD_ACTION

ALG-3-ENOMEM

3-Error

Memory allocation failed

An attempt to allocae memory has failed.

alg

LOG_STD_ACTION

ALG-3-ALG_REGISTRY_RC

3-Error

An ALG registry call failed with rc[chars]

The return code from an ALG registry call indicates an\n\ error.

alg

LOG_STD_ACTION

ALG-3-BAD_MAGIC

3-Error

Invalid magic number%#10x

An internal data structure is corrupt.

alg

LOG_STD_ACTION

ALG-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

alg

LOG_STD_ACTION

ALG-3-RUNAWAY_LOOP

3-Error

NULL

A loop has exceeded the expected number of iterations.

alg

LOG_STD_ACTION

ALPS-3-ALPSFAIL

3-Error

ALPS: Assertion failed: [chars]

An internal software error has occurred.

-

LOG_STD_ACTION

ALPS-5-PEER_CONN_ID_CHANGE

5-Notice

Peer [inet] [chars] ID modified to [inet] [chars].

An ALPS peer connection identifier has changed.

-

LOG_STD_NO_ACTION

ALPS-5-PEER_OPEN

5-Notice

Peer [inet] [chars] changed state to open.

An ALPS peer connection is now open.

-

LOG_STD_NO_ACTION

ALPS-5-PEER_CLOSED

5-Notice

Peer [inet] [chars] changed state to closed.

An ALPS peer connection is now closed.

-

LOG_STD_NO_ACTION

ALPS-5-PEER_CLOSED_DYNAMIC_INACTIVITY

5-Notice

Peer [inet] [chars] closed due to inactivity.

An ALPS peer connection is now closed due to inactivity.

-

LOG_STD_NO_ACTION

ALPS-6-PEER_OPEN_FAIL

6-Information

Peer [inet] [chars] open failed rsn = [chars]

An ALPS peer connection attempted to open but failed to open.

-

LOG_STD_NO_ACTION

ALPS-6-PEER_BUSY_START

6-Information

Peer [inet] [chars] has entered a congested state.

An ALPS peer connection is experiencing congestion.

-

LOG_STD_NO_ACTION

ALPS-6-PEER_BUSY_END

6-Information

Peer [inet] [chars] has exited a congested state.

An ALPS peer connection is no longer experiencing congestion.

-

LOG_STD_NO_ACTION

ALPS-7-PEER_DROPS_MAX_SIZE_EXCEEDED

7-Debug

Threshold exceeded for maximum size exceeded drops for peer [inet] [chars].

-

-

-

ALPS-7-PEER_DROPS_VERSION_MISMATCH

7-Debug

Threshold exceeded for version mismatch peer drops for peer [inet] [chars].

-

-

-

ALPS-7-PEER_DROPS_QUEUE_OVERFLOW

7-Debug

Threshold exceeded for TCP Queue overflow peer drops for peer [inet] [chars].

-

-

-

ALPS-7-PEER_DROPS_PEER_UNREACHABLE

7-Debug

Threshold exceeded for peer unreachable peer drops for peer [inet] [chars].

-

-

-

ALPS-5-CIRCUIT_OPEN

5-Notice

Circuit [chars] changed state to open.

An ALPS circuit has transitioned from closed to open.

-

LOG_STD_NO_ACTION

ALPS-5-CIRCUIT_CLOSED

5-Notice

Circuit [chars] changed state to closed rsn = [chars].

An ALPS circuit has tranistioned from open to closed

-

LOG_STD_NO_ACTION

ALPS-6-CIRCUIT_OPEN_FAILED

6-Information

Circuit [chars] received a Circuit Open Failed message rsn = [chars].

An ALPS circuit sent a Circuit Open Request message and\n\ received a Circuit Open Failed message as a reply.

-

LOG_STD_NO_ACTION

ALPS-6-CIRCUIT_ASCU_REJECT

6-Information

Circuit [chars] received a Circuit Open Confirm with a list of rejected ascus

An ALPS circuit sent a Circuit Open Request message and\n\ received a Circuit Open Confirm with a list of rejected ascus.

-

LOG_STD_NO_ACTION

ALPS-6-CIRCUIT_UPDATE_FAILED

6-Information

Circuit [chars] received a Circuit Open Failed message rsn = [chars].

An ALPS circuit sent a Circuit Update message and\n\ received a Circuit Open Failed message as a reply.

-

LOG_STD_NO_ACTION

ALPS-6-CIRCUIT_BUSY_START

6-Information

Circuit [chars] has entered a congested state.

An ALPS circuit is experiencing congestion.

-

LOG_STD_NO_ACTION

ALPS-7-CIRCUIT_BUSY_END

7-Debug

Circuit [chars] has exited a congested state.

An ALPS circuit is no longer experiencing congestion.

-

LOG_STD_NO_ACTION

ALPS-7-CIRCUIT_DROPS_QUEUE_OVERFLOW

7-Debug

Threshold exceeded for queue overflow drops for circuit [chars]

The number of ALPS circuit drops due to queue overflow \n\ exceeds the ALPS circuit threshold value.

-

LOG_STD_NO_ACTION

ALPS-7-CIRCUIT_DROPS_CKT_DISABLED

7-Debug

Threshold exceeded for circuit disabled drops for circuit [chars]

The number of ALPS circuit drops due to circuit disabled \n\ exceeds the ALPS circuit threshold value.

-

LOG_STD_NO_ACTION

ALPS-7-CIRCUIT_DROPS_LIFETIME_EXPIRED

7-Debug

Threshold exceeded for lifetime timer expiration drops for circuit [chars]

The number of ALPS circuit drops due to lifetime timer \n\ expiration exceeds the ALPS circuit threshold value.

-

LOG_STD_NO_ACTION

ALPS-7-CIRCUIT_DROPS_INVALID_ASCU

7-Debug

Threshold exceeded for invalid ASCU drops for circuit [chars]

The number of ALPS circuit drops due to invalid ASCU identifier \n\ exceeds the ALPS circuit threshold value.

-

LOG_STD_NO_ACTION

ALPS-7-CIRCUIT_DROPS_VC_RESET

7-Debug

Threshold exceeded for X.25 VC Reset drops for circuit [chars]

The number of ALPS circuit drops due to X.25 VC Reset \n\ exceeds the ALPS circuit threshold value.

-

LOG_STD_NO_ACTION

ALPS-6-CIRCUIT_X25_VC_STUCK

6-Information

Host unresponsive on X.25 VC for circuit [chars]

The X.25 or EMTOX host is not advancing the transmit window\n\ for extended periods of time. This may be indicative of a\n\ temporary problem with the host application. An X.25 Reset \n\ is sent to reset the transmit and receive windows to\n\ allow communication to proceed.

-

"None"

ALPS-5-ASCU_UP

5-Notice

ASCU %02x on interface [chars] is up.

An ALPS ASCU has transitioned from down to up.

-

LOG_STD_NO_ACTION

ALPS-5-ASCU_DOWN

5-Notice

ASCU %02x on interface [chars] is down.

An ALPS ASCU has transitioned from up to down.

-

LOG_STD_NO_ACTION

ALPS-3-ASCU_FSM_ERR

3-Error

ASCU %02x on interface [chars] has an internal FSM error.

Internal error.

-

"Turn debug flags on capture traces & contact Cisco technical support"

ALPS-3-ASCU_IF_STUCK

3-Error

Polling for ASCU %02x on interface [chars] is stalled.

The polling mechanism for an ALPS interface has become stuck.

-

LOG_STD_NO_ACTION

ALPS-5-ASCU_DISABLED_ASCU_STUCK

5-Notice

ASCU %02x on interface [chars] has been disabled since 4 consecutive messages were received from same SID.

An ALPS ASCU has been automatically disabled.

-

LOG_STD_NO_ACTION

ARAP-5-PAKINVALID

5-Notice

TTY [dec]: ARAP invalid packet received

This message appears only when ARA protocol logging is configured. The\n\ message notes that an ARA protocol user has logged out.

-

LOG_STD_NO_ACTION

ARAP-5-INITCONFUSED

5-Notice

TTY [dec]: ARAP unexpected initialization packet [chars]

The startup negotiation between a client and the ARA protocol server\n\ fell out of order. If this message is received sporadically it\n\ indicates line noise.

-

"If this message recurs reinstall the ARA client software."

ARAP-4-CONFAILED

4-Warning

TTY [dec]: ARAP connection failed: [chars]

The ARA protocol client was denied access probably due to a\n\ configuration problem on the server. The error message should indicate\n\ the problem. This message does not indicate access denials due to bad\n\ passwords.

-

"Investigate the problem reported in the error message."

ARAP-3-BADCONFIG

3-Error

TTY [dec]: unhandled configuration command

A configuration command was not recognized.

-

"Check the configuration file on the server for any invalid\n\ configuration commands."

ARAP-3-BADPAK

3-Error

TTY [dec]: Bad packet type in arap_send_msg

Internal data structures are corrupted.

-

"Check for abnormally high CPU usage."

ARAP-6-BADEXIT

6-Information

TTY [dec]: exited user [chars]: [chars]

A user was disconnected from ARA protocol at an unexpected time. The\n\ disconnection may be due to modems dropping server error client\n\ problems or any number of other difficulties.

-

"To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports."

ARAP-6-XTICKLE

6-Information

TTY [dec]: exited user [chars]: Other side stopped answering ARAP tickles\ mnp4 pak resent [dec] mnp4 pak sent [dec] last [dec] now [dec]

The router disconnected as the remote Macintosh client stopped\ sending ARAP tickle or data packets.

-

"To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports."

ARAP-6-MAXRESENDS

6-Information

TTY [dec]

The router resent MNP4 packets maximum number of times without\ receiving an acknowledgement.

-

"To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports."

ARAP-0-NULLRESEND

0-Emergency

TTY [dec]

An internal software error occured.

-

"Report this error to you technical support representative."

ARAP-0-NOTNULLRESEND

0-Emergency

TTY [dec]

An internal software error occured.

-

LOG_STD_SH_TECH_ACTION

ARAP-6-LRPHASERROR

6-Information

TTY [dec]: Received LT in CONNECTION PHASE

The router received an invalid packet during ARA connection setup\ phase.

-

"Check for excessive line noise.\ Check the ARAP client software configuration for\ possible problems."

ARAP-6-RCVNOPAK

6-Information

TTY [dec]: Receive getbuffer failure. dropping frame

No buffer exists for an incoming packet.

-

"Examine buffer usage statistics. Possibly more memory is\ required."

ARAP-6-RCVGIANT

6-Information

TTY [dec]: Rcv giant. dropping frame

The router received an oversized MNP4 frame.

-

"Check for excessive line noise.\ Check the ARAP client software configuration for\ possible problems."

ARAP-0-DEFAULT

0-Emergency

TTY [dec]

An internal software error occured.

-

LOG_STD_SH_TECH_ACTION

ARAP-0-WAITBADMSG

0-Emergency

TTY [dec]: arg msg bad [hec]

The router received an invalid packet during ARAP MNP4 connection\ setup phase.

-

"Check for excessive line noise.\ Check the ARAP client software configuration for\ possible problems."

ARAP-0-VSERROR

0-Emergency

TTY [dec]: VS queued error

An internal software error occured.

-

LOG_STD_SH_TECH_ACTION

ARAP-6-MNP4T401

6-Information

TTY [dec]: T401 [dec] baud rate [dec]

This message indicates that the router received MNP4 connection\ request. MNP4 acknowledgement timer value is also indicated.

-

LOG_STD_NO_ACTION

ARAP-6-RESENDSLOW

6-Information

TTY [dec]

The router repeated resending of MNP4 packets as the\ Macintosh client failed to acknowledge previously resent packets.

-

"If this error message persists for several ARAP connections\ report it to your technical support representative."

ARAP-2-NOLOG

2-Critical

TTY [dec]: Could not malloc log

Memory not available for internal MNP4 logging.

-

LOG_STD_SH_TECH_ACTION

ARAP-6-MNP4RCVDISC

6-Information

TTY [dec]: MNP4 input disconnect

This indicates that the router received disconnect request\ from the remote Macintosh client.

-

LOG_STD_NO_ACTION

ARAP-3-REMOTEERROR

3-Error

TTY [dec]: arap input error

ARAP connection was terminated without a known cause.

-

LOG_STD_ACTION

ARAP-6-TIMERERROR

6-Information

TTY [dec]: MNP4 timeout error

The router is dropping the connection after doing maximum resends.

-

"To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports."

ARAP-4-NOEXTTACACS

4-Warning

TTY [dec]: arap TACACS is configured but extended TACACS is not.

-

-

"Configure extended TACACS."

ARAP-3-ABORTED

3-Error

TTY [dec]: arap callback aborted

An unexpected message was received during the Microcom Networking\n\ Protocol version 4 MNP4 link setup.

-

LOG_STD_ACTION

ARAP-3-TIMEOUT

3-Error

TTY [dec]: arap expected message timeout

The SCP process has been terminated.

-

"If this message recurs copy the error message exactly as it appears\n\ and report it to your technical support representative."

SCP-3-NOQUEUE

3-Error

Cannot create SCP Rx/Tx queue.

Insufficient internal resource available to create queue.

-

"Check available memory capacity on router."

SCP-3-NOPROC

3-Error

Cannot create SCP process.

Insufficient internal resource available to create queue.

-

"Check available memory capacity on router."

SCP-3-UNKMSG

3-Error

Unknown SCP message opcode 0x[hec] received.

The remote peer sent an SCP message we don't know about.

-

"Check software compatibility between peers."

SCP-3-BADVLAN

3-Error

Rx'd VLAN [dec] opcode 0x[hec] from the NMP which is not configured.

The NMP sent a config command for an unconfigured VLAN interface.

-

"Configure VLAN interface."

TRUNK_CLOCK-6-TRUNK

6-Information

Switching to the user configured trunk clock on slot [dec] port [dec] priority [dec]

The TDM primary clock is switching from the default clock to the\n\ user configured trunk clock.

as

LOG_STD_NO_ACTION

TRUNK_CLOCK-6-EXTERNAL

6-Information

Switching to the user configured external clock on motherboard

The TDM primary clock is switching from the default clock to the\n\ user configured external clock in motherboard.

as

LOG_STD_NO_ACTION

TRUNK_CLOCK-6-FREERUN

6-Information

Switching to the user configured freerunning clock on motherboard

The TDM primary clock is switching from the default clock to the\n\ user configured free running clock in motherboard.

as

LOG_STD_NO_ACTION

TRUNK_CLOCK-6-BAD_CLOCKS

6-Information

There are no good clocks in the system. Remain in HOLDOVER mode

The clock selection algorithm has failed to select any clock as \n\ the TDM primary clock.

as

LOG_STD_NO_ACTION

TRUNK_CLOCK-6-SWITCH

6-Information

Switching to the clock on slot [dec] port [dec] priority [dec] as the current primary has gone bad

The TDM primary clock has switched to a backup clock coming in \n\ via the specified trunk as the current primary clock has gone\n\ bad.

as

LOG_STD_NO_ACTION

TRUNK_CLOCK-3-NOMEMORY

3-Error

Failed to allocate memory for the clocks

The clock switching software has failed to allocate memory\n\ while adding a clock.

as

LOG_STD_NO_ACTION

SW56-1-INITSYS

1-Alert

[chars]

Failed SW56 Initialization. Most likely because lacking of memory

as

"The amount of memory available in the router may not be " "sufficient." LOG_STD_ACTION

SW56-3-ERR_MSGQ

3-Error

[chars]

Failed to send message to internal software process

as

LOG_STD_ACTION

MODEM_NV-5-FLEXIBLE

5-Notice

[chars]

This message type is created for all those messages which\n\ have simple ASCII text and does not take any parameter.\n\ Message tells what the problem is.

as

LOG_STD_ACTION

CSM_VOICE-3-UNDEFVOICEINTRF

3-Error

Invalid voice interface controller:group[dec]:[dec]

The voice interface defined by controller:group is not\n\ yet defined within the voice software but attempts were\n\ made to use this interface.

as

"Internal software fault. Contact your field service \n\ representative if this message is coincident with \n\ dropped calls."

CSM_VOICE-3-UNDEFDSX0

3-Error

Undefined dsx0 interface for controller[dec]

The dsx0 interface for the specified controller\n\ is not defined but the voice software use it.

as

"Internal software fault. Contact your field service representative \n\ if this message is coincident with dropped calls."

CSM_VOICE-3-NOSDB

3-Error

No signaling data block is available to build the \n\ voice interface[dec]:[dec]

The voice software was unable to obtain a signaling data\n\ block from the Voice Telephony Service Provider. \n\ The system may be out of memory.

as

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-ADDINTRFFAIL

3-Error

The Voice Telephony Service Provider has rejected our\n\ request to add this voice interface [dec]:[dec]

The voice software was unable to report a new signaling\n\ interface to the Voice Telephony Service Provider

as

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-NOMEM

3-Error

No memory is available to build the voice interface [dec]:[dec]

The voice software was unable allocate memory to build \n\ a voice interface data structure. The system may be \n\ out of memory.

as

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-MALLOC

3-Error

No memory is available to build any internal data \n\ structure for the voice software.

The voice software was unable allocate memory to build \n\ any internal data structures. The system may be \n\ out of memory.

as

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-NOTDMCHNL

3-Error

CSM failed to get a free dsp tdm channel from the DSP\n\ Resource Manager DSPRM to handle an incoming call

The voice software was unable to obtain the tdm channel \n\ for a free dsp from the DSP Resource Manager. All of \n\ the dsp's have been used to process calls or have\n\ been taken out of service.

as

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-TDMHPMADDFAIL

3-Error

CSM failed to add the CAS TDM hairpinning call

The CSM voice software interface was unable to add\n\ this call as hairpinning because of presence of\n\ another call for the same DS0. Internal software error.

as

LOG_STD_SH_TECH_ACTION

MICA-3-UNEXPEVT

3-Error

Modem[dec]/[dec] Unexpected Event: [chars] in [chars]

An error was reported from the modem hardware which was not\n\ expected by the driver.

as

"The seriousness of this problem has not been determined.\n\ If the determination is not obvious from the error message\n\ provided from the device follow these instructions: " LOG_STD_ACTION

MICA-3-NOBUF

3-Error

No msg buffer for Modem[dec]/[dec] in [chars]:[dec]

The MICA software was unable to allocate a packet buffer. The system\n\ may be out of memory.

as

LOG_STD_SH_TECH_ACTION

MICA-3-BADMSG

3-Error

Bad msg from modem[dec]/[dec]: opcode/arg = 0x[hec]/0x[hec]

A message received from the modem was not expected by the driver.\n\ If the hardware is newer than the software this could mean a\n\ new response cannot be handled. Otherwise it is possible that\n\ data corruption has occurred in the hardware.

as

LOG_STD_SH_TECH_ACTION

MICA-3-RCR

3-Error

Slot [dec] Looking for [hec] but reading [hec]

The MICA driver timed out waiting for a specific response.

as

LOG_STD_RECUR_ACTION

MICA-3-NOBOARDWARE

3-Error

Boardware is not bundled in this IOS image

-

as

LOG_STD_ACTION

MICA-3-BOARD_DL_FAIL

3-Error

Slot [dec] Boardware download failed because of [chars] all modems are marked bad

-

as

"Try powercycling the router. " LOG_STD_RECUR_ACTION

MICA-4-PWDL_FILENOTFOUND

4-Warning

Slot [dec] Module numbers [chars] are running default IOS image file [chars] not found in flash

-

as

LOG_STD_NO_ACTION

MICA-5-BOARDWARE_RUNNING

5-Notice

Slot [dec] is running boardware version [chars].[chars].[chars].[chars]

This is a status message to indicate the successful start-up\n\ of the on-board software boardware on one MICA modem port.

as

LOG_STD_NO_ACTION

MICA-1-BRDCRASHED

1-Alert

Slot [dec] MICA Board Crashed Going to Recover

A MICA modem board has crashed. The router will automatically\n\ restart and reload it.

as

LOG_STD_RECUR_ACTION

MICA-1-BRDINITFAIL

1-Alert

Slot [dec] MICA Board Init Failed : [chars]

A MICA modem board has failed to reset and initialize.

as

LOG_STD_RECUR_ACTION

MICA-5-MODEM_RECOVERY

5-Notice

Modem [dec]/[dec] is being recovered by [chars]

Modem is consecutively failing to Connect so being recovered

as

"None"

MICA-5-MODEM_RECOVERY_FAIL

5-Notice

Modem [dec]/[dec] recovery failed: [chars]

Modem recovery failed

as

"None"

MICA-5-UNKNMODEM

5-Notice

Unknown modem module in Slot [dec] - Modem Module [dec]

A MICA modem module has an uninitialized cookie. This can be due to\n\ a manufacturing error or more likely it is due to a problem on\n\ the modem module itself.

as

"Please seek a replacement for this modem module. For\n\ some reason this module no longer is able to identify itself" LOG_STD_NO_ACTION

MICA-1-BOOTFLASH

1-Alert

[chars]

MICA modem FIRMWARE download file is not found in BOOTFLASH.

as

"Record the reason at the end of the message and report the problem."

MICA-3-MODEMBAD

3-Error

Modem number [dec]/[dec] is bad Error code is [hec]

Message from the MICA modem driver indicates that the modem is bad.

as

LOG_STD_ACTION

MICA-3-INBANDNAK

3-Error

Inband NAK from modem [dec]/[dec]: opcode = 0x[hec]

A inband message sent to the indicated modem was rejected.

as

LOG_STD_RECUR_ACTION

MICA-3-UNKNINBAND

3-Error

Unknown inband msg from modem [dec]/[dec]: opcode = 0x[hec]

An unknown inband message is received from the indicated modem.

as

LOG_STD_RECUR_ACTION

MICA-4-DCCHANRESET

4-Warning

OOB comand in Slot[dec] took too long to complete. Reseting port

The OOB port was locked because a command took too long\n\ to complete. The port was recovered by reseting internal\n\ datastructures.

as

"If there are frequent occurances of this event\n\ turn on debug modem oob for the slot and report\n\ the problem with these logs"

MICA-3-NOMEMORY

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

CALLRECORD-3-MCOM_TERSE_CALL_REC

3-Error

[chars]

Terse Mcom Call Record

modem-management

LOG_STD_NO_ACTION

CALLRECORD-3-MCOM_TERSE_CALL_FAILED_REC

3-Error

[chars]

Terse Mcom Call Failed Record

modem-management

LOG_STD_NO_ACTION

CALLRECORD-3-MICA_TERSE_CALL_REC

3-Error

[chars]

Terse Mica Call Record

modem-management

LOG_STD_NO_ACTION

CALLRECORD-3-MICA_TERSE_CALL_FAILED_REC

3-Error

[chars]

Terse Mica Call Failed Record

modem-management

LOG_STD_NO_ACTION

CALLRECORD-3-MODEM_CALL_REC_ERROR

3-Error

[chars]

Record Generated Exceeded Syslog Capability

modem-management

LOG_STD_NO_ACTION

FREEDM-3-REG_READ_TIME_OUT

3-Error

Busy Out Error of FREEDM [dec] [chars]

Trying to read FREEDM internal RAM Busy bit is still set for\n\ more than 10 seconds.

as

LOG_STD_SH_TECH_ACTION

VFC-1-UNKNOWN_DSPM

1-Alert

vfc[dec] vfc dspm daughter card has an unknown id of [hec]

The software did not recognize the type of DSP module \n\ plugged into the voice card.

-

"Check the part number on the dspm card to see if it is supported\n\ in the version of IOS operational on the router or contact\n\ your technical support representative."

VFC-1-NO_DSPM

1-Alert

vfc[dec] No dsp module has been found.

The software did not find any of DSP module plugged\n\ into the voice card.

-

"Check the part number on the dspm card to see if it is supported\n\ in the version of IOS operational on the router or contact\n\ your technical support representative."

VFC-1-INVALID_CONFIGURATION

1-Alert

vfc[dec] vfc cards has an invalid configuration.

The software did recognized more dsp interface port than it can \n\ support on this card.

-

"Check the part number on the VIC card to see if it is supported\n\ in the version of IOS operational on the router or contact\n\ your technical support representative."

VFC-3-INCORRECT_ID

3-Error

VFC in slot [dec]: PCI device not supported.

A interface controller device did not report correct device\n\ ID

-

"Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance."

VFC-1-NODPMEMORY

1-Alert

VFC [dec]/[dec] vfc dual-ported memory unavailable.

The router or access server could not allocate dual-ported memory for the\n\ descriptors.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VFC-1-INCORRECT_DSP_ID

1-Alert

VFC in slot [dec]: Incorrect [dec] DSP-ID passed by SPI.

The DSP ID provided by the SPI for download is not valid.

-

" Call your technical support representative for assistance."

VFC-3-ERROR_INIT_BLDR

3-Error

[chars] Unable to download the Boot loader firmware ret = 0x[hec]

Error initializing the DSP with the bootloader firmware.

-

" Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance."

VFC-3-ERROR_INIT_OVERLAY

3-Error

[chars] Unable to download the Application overlay firmware. Status returned 0x[hec]

Error initializing the DSP with the application/overlay firmware.

-

" Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance."

VFC-1-TOOBIG

1-Alert

[hec] packetsize [dec] too big.

A packet greater than the 256 bytes received on this interface.

-

"The system should recover. No action is required.\n\ \n\ If the problem reccurs it indicates an error that might be\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative."

VFC-1-ERROR_INTR

1-Alert

[chars] Error interrupt occured type = 0x[hec].

The DMA engine cannot get to the PCI bus to read descriptors.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VFC-3-ERROR_ANALYZE

3-Error

[chars] Error analyzing the device in slot [dec].

The feature card in this slot could not be recognized.

-

"Power down reinsert voice feature card and reboot.\n\ If message recurs call your technical support representative for\n\ assistance."

VFC-1-NO_RING_DESCRIPTORS

1-Alert

No more ring descriptors available on [dec] slot.

The VFC driver cannot queue messages onto Rossini dma engine for transmit.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. Reset the DSP's on this port \n\ module."

AT-3-NOTRUNNING

3-Error

AppleTalk not running

An AppleTalk interface that was previously shut down was restarted.

atalk

LOG_STD_NO_ACTION

AT-6-BADROUTE

6-Information

Route to %#A has gone bad

The system did not detect a route within the required timeout period. Therefore the route is marked as bad. A network might have become unreachable for some reason perhaps because of a broken connection. This message does not necessarily indicate an error condition.

atalk

LOG_STD_NO_ACTION

AT-5-PATHCHANGE

5-Notice

Route to %#A is now using path of type [chars] on [chars] via %#a

The path to a network changed because either the old path went down or the new path was better.

atalk

LOG_STD_NO_ACTION

AT-5-RTMPSTATE

5-Notice

[chars]: RTMP path to %#A via %#a now in [chars] state metric [dec] [dec] hops

A new AppleTalk path has been learned. The message indicates the source of the path its distance in hops its metric and the type of path.

atalk

LOG_STD_NO_ACTION

AT-6-PATHDEL

6-Information

[chars]: AppleTalk [chars] path to %#A via %#a has been deleted

An AppleTalk node sent a GetNet Info request to this router specifying an invalid network number for the source of the GetNet Info request. This situation occurs when an AppleTalk end node is moved to another network and is therefore misconfigured for the current network.

atalk

LOG_STD_NO_ACTION

AT-7-BUGREPORT

7-Debug

AppleTalk bug: [chars]

The software detected an unexpected condition. The router takes corrective action and continues.

atalk

"Copy the message exactly as it appears note any AppleTalk problems " "you experience and call your technical support representative."

AT-2-ASSERTFAILED

2-Critical

AppleTalk assertion failed: [chars]

The software detected an inconsistency. Although this error is serious the router attempts to continue. AppleTalk processing might be impaired.

atalk

"Copy the message exactly as it appears note any AppleTalk problems " "you experience and call your technical support representative."

AT-7-DEBUGMSG

7-Debug

AppleTalk debug: [chars]

This message is generated by a debug command and provides additional information about an AppleTalk condition.

atalk

"Copy the message exactly as it appears note any AppleTalk problems " "you experience and call your technical support representative."

AT-5-COMPATERR1

5-Notice

[chars]: AppleTalk internet compatibility mode required by %#a

Although this router has neighbors that require your internetwork to observe compatibility rules AppleTalk has learned of a route that has a cable range greater than 1. This condition can cause node inconsistencies on your AppleTalk network.

atalk

"Upgrade the routers that support only the original AppleTalk " "specification. In the meantime observe the compatibility rules " "for AppleTalk Phase 1 and Phase 2 routers."

AT-5-FDDICOMPAT

5-Notice

AppleTalk FDDI neighbor %#a using obsolete FDDI addressing

An attempt was made to configure an interface to have the same or a conflicting AppleTalk address or cable range as another interface on the same router.

atalk

"Verify that you are not specifying an AppleTalk address or cable range " "used previously on this router and reconfigure the interface."

AT-3-SUBROUTINE_ERROR

3-Error

AppleTalk error: [chars]

An internal error occurred. Specifically a programming assertion in the AppleTalk networking code was violated.

atalk

LOG_STD_ACTION

AT-6-MACIPUP

6-Information

[chars]: MacIP server operational [inet]

If the appletalk event-logging command is configured this message appears on the console when a MacIP server is fully initialized and is ready to accept client requests. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command.

atalk

LOG_STD_NO_ACTION

AT-6-MACIPDOWN

6-Information

[chars]: MacIP server shutting down [inet]

If the appletalk event-logging command is configured this message appears on the console when a MacIP server is no longer operational for any reason. MacIP servers shut down in response to MacIP configuration changes or errors or a change in the condition or configuration of an AppleTalk or IP interface for which the MacIP server is providing service. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command.

atalk

LOG_STD_NO_ACTION

AT-4-MACIPBADCONF

4-Warning

[chars]: MacIP inoperable configuration [inet]

If the appletalk event-logging command is configured this message appears on the console when a MacIP server cannot begin or recover operations because of an invalid IP address configuration. This condition only occurs when the configured MacIP server's IP address is not valid on the same cable of any operable IP interface. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command. When this error occurs the MacIP configuration is considered invalid and is deleted.

atalk

LOG_STD_NO_ACTION

AT-4-MACIPNOCABLE

4-Warning

[chars]: MacIP inoperable IP interface [inet]

If the appletalk event-logging command is configured this message appears on the console when a MacIP server can no longer operate due to a change in the condition of the IP interface it serves. This condition can occur if IP routing is shut down on the interface or the IP address of the interface is changed so that the MacIP server's IP address is no longer valid on the same cable. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command.

atalk

LOG_STD_NO_ACTION

AT-5-NOSUCHROUTE

5-Notice

No such route [dec]

You specified a nonexistent route in a show appletalk route or clear appletalk route command.

atalk

"Specify a valid route that is one that appears in the output of the " "show appletalk route command."

AT-3-NOSUCHNBR

3-Error

No such neighbor %#a

You specified a nonexistent neighbor address in a show appletalk neighbor or clear appletalk neighbor.

atalk

"Specify a valid neighbor address that is one that appears in the " "output of the show appletalk neighbor command."

AT-6-NBRDELETED

6-Information

Neighbor entry for %#a deleted

The clear appletalk neighbor command displays this command when it completes successfully.

atalk

LOG_STD_NO_ACTION

AT-6-REGPENDING

6-Information

NBP registration of [chars] at [[chars]] pending

A name registration call is being performed.

atalk

LOG_STD_NO_ACTION

AT-1-NOMEM

1-Alert

Could not allocate memory for [chars] at line [dec] in [chars]

An internal software error occurred.

atalk

LOG_STD_SH_TECH_ACTION

AT-3-NOBESTPATH

3-Error

Could not compute best path for network %#A

A path to the specified network could not be found.

atalk

"Use the show appletalk route command to verify that a path to the " "specified network exists. If it does copy the error message exactly " "as it appears and report it along with the output of the show " "appletalk route command to your technical support representative."

AT-3-NOROUTE

3-Error

No route to destination [atalk_address]

You attempted to remove a route from the routing table by issuing the clear appletalk route command. The command failed because the route was on a directly connected interface that is it was created when you configured the router.

atalk

"Remove the route by reconfiguring the directly connected interface " "with which it is associated."

AT-3-INVNBPCMD

3-Error

Invalid NBPtest command [chars]

An unrecognized command was specified in the Name Binding Protocol NBP test facility.

atalk

"Enter a valid command."

AT-3-OUTOFSYNC

3-Error

[chars]: AURP connection out of sync...terminating

The router detected a conflicting cable range. A router is configured with a cable range that overlaps with an existing range but does not match the entry exactly.

aurp

"Use the show appletalk command to identify the overlapped cable range " "and then reconfigure the misconfigured router."

AT-3-DOMOVERFLOW

3-Error

Remap range overflow for [chars] domain [dec]

The remap range overflowed. If a network range cannot fit inside the

atalk

"Use the appletalk domain remap-range command to increase the remapping " "range. Then restart the interfaces."

AT-3-DOMLOOP

3-Error

Loop detected on domain [dec] [[chars]]

The domain router detected a routing loop. Routing loops are not allowed. The domain router runs a background loop detection process. The domain router starts this process when it receives a new zone list from a domain that is identical to the list in the main routing table and whose network range length matches that in this list. The loop detection process sends several AppleTalk NBP loopback packets. When one of these packets is received on an interface that does not belong to the original domain the domain router first shuts off all the domains involved in the loop and then shuts off all the interfaces in these domains. The loop detection does not catch all types of loops. It is your responsibility to make sure that no loop exists.

atalk

"Disable the cause of the routing loop. Then use the clear appletalk " "command to restart the interfaces involved."

AT-3-NOVIRTUAL

3-Error

[chars]: client tried to connect but no virtual network is declared

A hardware or software error occurred.

atalk

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AT-3-NOSOCKET

3-Error

[chars]: client tried to open socket but failed

-

-

-

ATMSIG-3-FAILASSERT

3-Error

Assertion failed: [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-NOSVC

3-Error

no SVC [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-NOCALLREF

3-Error

Cannot find a Callref value to allocate: [chars]

This indicates an internal software error probably including\n\ memory exhaustion.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_SVC_INSERT_FAILED

3-Error

ATMSIG[chars] [dec][dec] - %04d/%02d SVC wavl ins failed:svc 0x[hec]

A software error occurred during creation of an SVC. Other error\n\ messages appearing immediately prior to this one may be related.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_SVC_DELETE_FAILED

3-Error

ATMSIG[chars] [dec][dec] - %04d/%02d SVC wavl del failed:svc 0x[hec]

A software error occurred during closure of an SVC. Other error\n\ messages appearing immediately prior to this one may be related.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_PRTY_INSERT_FAILED

3-Error

ATMSIG[chars] [dec][dec] - %04d/%02d avl prty ins failed:svc 0x[hec] party 0x[hec]

A software error occurred during addition of a party to a\n\ point-to-multipoint call. Other error messages appearing\n\ immediately prior to this one may be related.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_PRTY_DELETE_FAILED

3-Error

ATMSIG[chars] [dec][dec] - %04d/%02d avl prty del failed:svc 0x[hec] party 0x[hec]

A software error occurred during removal of a party from a\n\ point-to-multipoint call. Other error messages appearing \n\ immediately prior to this one may be related.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_CUG_INSERT_FAILED

3-Error

ATMSIG[chars]

A software error occurred during addition of a member to a\n\ closed user group. Other error messages appearing\n\ immediately prior to this one may be related.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_CUG_DELETE_FAILED

3-Error

ATMSIG[chars]

A software error occurred during removal of a member from a\n\ closed user group. Other error messages appearing\n\ immediately prior to this one may be related.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-FAILHALFLEGREM

3-Error

halfLeg removal failed [chars]

An internal software error occurred. This message should only\n\ be displayed when verbose debugging is enabled for an SVC.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-FAILXCONN

3-Error

Xconnect failed [chars]

An internal software error occurred during installation of an\n\ SVC cross-connect.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-INVPNNIMSG

3-Error

Invalid msg from routing/pnni : [chars]

This message indicates an error in the PNNI routing subsystem.\n\ It could be caused by an internal software error or by bad\n\ control information received from peer equipment. The message\n\ will contain additional information that can help locate the\n\ cause. Any message with 'NULL' probably indicates a problem\n\ with this system others probably point at the peer equipment.

-

"Check this system and the peer equipment for any obvious errors. " LOG_STD_RECUR_ACTION

ATMSIG-4-CONFIG_ERROR

4-Warning

Configuration Error: [chars] [chars]

This message indicates a configuration error in the ATM Signaling\n\ subsystem. The message will display more specific information\n\ about the problem location.

-

"Change the configuration to correct the error."

ATMSIG-3-FAIL1STHALFLEG

3-Error

1st halfLeg failed [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-FAIL2NDHALFLEG

3-Error

2nd halfLeg failed [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ENQFAIL

3-Error

process_enqueue failed [chars]

An internal software error occurred while handling a user request.

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-DBINITFAIL

3-Error

Signalling control block initialization failure [chars]

An internal software or resource error occurred

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-ATMSIG_LISTEN_FAILED_DUP

3-Error

Duplicate LISTEN by [chars] for existing NSAP [chars] owned by [chars]

An application attempted to either LISTEN on an NSAP owned by \n\ another application or to LISTEN for the same NSAP twice

-

LOG_STD_SH_TECH_ACTION

ATMSIG-3-PNNI_TRACE_INTERNAL

3-Error

[chars]

An internal software error or unexpected condition occured during\n\ PNNI Connection/Path Trace related processing

-

-

ATMSSCOP-4-UNMATCHUNIVERSION

4-Warning

[chars]: [chars]. Please verify peer UNI version

The ATM peer equipment appears to be running an old version of\n\ ATM UNI. Communication with it is not possible.

-

"The ATM peer equipment may need attention. \Please verify its UNI version is at least 3.1 and upgrade if necessary."

ATMSSCOP-3-SSCOPERR

3-Error

INIT SSCOP -\nIntf : [chars] Event : [chars] State : [chars].

A software error occurred in the ATM SSCOP subsystem.

-

LOG_STD_SH_CMD_ACTION

ATMSSCOP-5-SSCOPINIT

5-Notice

- Intf : [chars] Event : [chars] State : [chars].

This message indicates a routine step of the ATM SSCOP\n\ initialization sequence.

-

LOG_STD_NO_ACTION

ATMCORE_RED-2-INTERNAL_CRITICAL

2-Critical

[chars]

The ATM core redundancy subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE_RED-3-INTERNAL_ERROR

3-Error

[chars]

The ATM core redundancy subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE_RED-4-INTERNAL_WARNING

4-Warning

[chars]

The ATM core redundancy subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE-2-INTERNAL_CRITICAL

2-Critical

[chars]

The ATM core subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE-3-INTERNAL_ERROR

3-Error

[chars]

The ATM core subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE-4-INTERNAL_WARNING

4-Warning

[chars]

This warning is generated by the ATM core subsystem to the user. This could arise because the user request may not be granted due to some existing configuration on the device. This message serves as an alert to the user. This message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE-4-ATM_SYS_ERROR

4-Warning

[chars]

The ATM core subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

ATMCORE-4-CONFIG_ERROR

4-Warning

Configuration Error: [chars]

This message indicates a configuration error. The message will display more specific information about the problem location.

-

"Change the configuration to correct the error."

RAC-3-RACNOIPL

3-Error

Can not find lease information for interface [chars]

Internal error - DHCP lease information is missing for the interface

-

"Report the problem and how it can be reproduced to Cisco TAC"

RAC-3-RACNOQ

3-Error

Can't create RAC work queue

Internal error - probable cause is insufficient memory resources

-

"Check available memory."

RAC-3-RACIPL

3-Error

DHCP is already running on interface [chars]

The interface already has a DHCP originated address via some other system mechanism

-

"Verify the system configuration"

AUTO_IP_RING-5-EQUAL_AUTOIP_PRIORITY

5-Notice

Port[chars]: Received the same priority[dec] as the peer device

Auto-IP Ring feature requires two neighbor devices to exchange different Auto-IP priority for IP auto-negotiation to happen. If they advertise the same Auto-IP priority then the IP auto-negotiation will not happen. This may indicate that the ring ports of the two devices are either wrongly wired or there is a missing seed configuration.

auto_ip_ring

"Use the 'show auto-ip-ring' or 'show run' command" " on both devices to view the IP addresses of the ring ports and the" " advertised/received Auto-IP priorities. If the Auto-IP priority is both 2" " or both 0 it represents a faulty wire connection that can be fixed by" " switching the two ring ports on one of the devices as necessary." " If the Auto-IP priority is both 1 there are two possibilities based on" " the mode. In pre-config mode manually configure an IP address on one" " device to start the Auto-IP negotiation. In auto-config mode if the" " Auto-IP server is reachable then configure 'auto-ip-ring <ring-d> seed'" " on one ring port of the device."

AUTO_IP_RING-5-DUPL_AUTOIP_ADDRESS

5-Notice

Neighbor device advertised the same configured Auto-IP address[inet]

Auto-IP Ring feature requires each device to configure a unique auto-ip address different from those on other devices. The local device is configured with an Auto-IP address. However the local device has also received the same Auto-IP address from a neighbor device. This may indicate that two devices are configured with the same Auto-IP address.

auto_ip_ring

"Use the 'show auto-ip-ring' or 'show run' command" " on both devices to view the configured Auto-IP address. If two edge" " devices show the same configured Auto-IP address then the duplicate" " configured Auto-IP address needs to be removed."

AUTO_IP_RING-5-AUTOIP_IP_ADDR_SUCCESS_PORT

5-Notice

IP address[inet] is assigned to the ring port[chars] successfully

IP address is assigned to the ring port successfully.

auto_ip_ring

"Use the 'sh ip interface' or 'show run' command" " to view the IP address of the ring port."

AUTO_IP_RING-5-AUTOIP_HOST_INSERT_SUCCESS

5-Notice

IP addresses[inet]/31 [inet]/31 are assigned to the ring ports[chars] [chars]

IP addresses are assigned to the ring ports and the device is inserted into the ring successfully

auto_ip_ring

"Use the 'show auto-ip-ring' or 'show run' command" " on the device to view the configured IP addresses on the ring ports."

AUTO_IP_RING-5-AUTOIP_HOST_ADD_SUCCESS

5-Notice

IP address[inet]/31 is assigned to the ring port[chars] and

IP address is assigned to the ring port and the device is added to the ring successfully

auto_ip_ring

"Use the 'show auto-ip-ring' or 'show run' command" " on the device to view the configured IP address on the ring port."

AUTO_IP_RING-5-LLDP_NOT_ENABLE_ON_THIS_INTERFACE

5-Notice

port [chars]: lldp not enabled for interface please enable lldp on

Auto-ip depends on lldp to communicate with it's peer. So configure lldp before auto-ip configuration

auto_ip_ring

"Configure 'lldp run' in global config mode and" " check 'sh lldp neighbors'"

AUTO_IP_RING-5-AUTOIP_ADDRESS_POOL_EXHAUST

5-Notice

Free IP addresses are not available in the Auto-IP Server pool. Configure additional pools to get IP addresses for the requesting

The Auto-IP server is configured with pools of Auto-IP addresses. The IP addresses are assigned to the requesting ring ports. The Auto-IP address pool is exhaused and there are no more free addresses.

auto_ip_ring

"Configure additional address pools in the" " Auto-IP server by using the configuration command" " 'auto-ip-ring server' and the sub command" " 'ipv4-address-pool <auto-ip-base-address> <num of nodes in ring>"

BEEP-3-SLOG_LINE

3-Error

[chars] [chars]

This is an internal BEEP library error message.

beep

LOG_STD_ACTION

BEEP-3-SLOG_LINE_TB

3-Error

[chars] [chars]

This is an internal BEEP library error message.

beep

LOG_STD_ACTION

BEEP-3-SESSION_ERR

3-Error

[chars] at [chars]:[dec]

The BEEP subsystem had an error and may stop running.

beep

LOG_STD_ACTION

BSC-3-BADPEERTYPE

3-Error

Peer [chars] is incorrect type

This message occurs only when BSC local-ack is configured. It\n\ indicates the serial interfaces that are using the BSTUN tunnel are\n\ configured incorrectly that is both have been configured as a\n\ secondary.

-

"Reconfigure the serial interfaces correctly to be a primary and\n\ secondary pair."

BSC-2-NOMEM

2-Critical

No buffers available on interface [chars].

This message indicates that memory in the router was exhausted.

-

"Perform diagnostics on the router to locate the subsystem or interface\n\ responsible for consuming memory. The only method that will clear this\n\ situation is to reload the router."

BSC-3-BADLINESTATE

3-Error

Line state Tx when receiving [chars] on line [chars]

An unexpected receive occurred during a transmission.

-

"Verify that the line has been consistently defined in regards to the\n\ carrier. If a message report was sent hard-on stop and start the\n\ bisynchronous interface in question."

BSTUN-4-DUPROUTE

4-Warning

Cannot define duplicate route on the\n\same group

This route command is defined on another interface belonging to the\n\same group. Cannot define duplicate route on the same group

-

"Consider defining a new group and moving this interface onto that\n\group"

BSTUN-4-PEERSTATE

4-Warning

Peer [chars] wrong state [dec] [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-3-BADMAGIC

3-Error

[chars]: wrong magic mine [hec] theirs [hec] [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-3-BADMAGICTCP

3-Error

[chars]: peer [chars] wrong magic mine [hec] theirs [hec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-3-BADLENOP

3-Error

[chars]: bad len or unknown op op [dec] len [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-6-TCPPEERSHUT

6-Information

[chars] [chars] [inet][dec]

This route closed a BSTUN connection with a remote peer.

-

"Examine this router to see why it closed this connection with this\n\ peer. This can be caused by normal events such as reconfiguration."

BSTUN-3-CONNILLSTATE

3-Error

CONN: Peer [chars] illegal state [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-3-BADCONN

3-Error

CONN: bad connection [dec] peer: [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-6-ERR

6-Information

[chars]: [chars]: [chars] op [hec] len [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-3-SENDPUNT

3-Error

[chars]: sent [chars] to [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-4-SENDPUNTTCP

4-Warning

[chars]: sent [chars] to [[dec]][inet]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-6-OPENING

6-Information

CONN: opening peer [chars] [dec]

-

-

LOG_STD_NO_ACTION

BSTUN-6-CONNOPENFAIL

6-Information

CONN: peer [chars] open failed [chars] [[dec]]

An attempt to connect to a remote TCP BSTUN peer failed.

-

"Verify that the remote peer is accessible from this router that it is\n\ running software capable of supporting BSTUN and that it is configured\n\ correctly."

BSTUN-3-BADPASSIVEOPEN

3-Error

passive open from [inet][dec] -> [dec] failed

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

BSTUN-6-PASSIVEOPEN

6-Information

passive open [inet][dec] -> [dec]

-

-

LOG_STD_NO_ACTION

BSTUN-6-TCPFINI

6-Information

peer [chars] closed [previous state [chars]]

A remote peer closed a BSTUN connection with this router.

-

"Examine the other router to see why it closed this connection with\n\ this peer. This can be caused by normal events such as\n\ reconfiguration."

BSTUN-6-PEERSHUTDOWN

6-Information

shutting down peer [chars] on [chars]

A connection to a remote peer is being shut down. This is typically\n\ the result of user intervention in BSTUN reconfiguration or disabling.\n\ This is good expected behavior.

-

LOG_STD_NO_ACTION

BSTUN-6-OPENED

6-Information

[chars]: peer [chars] opened [previous state [chars]]

-

-

LOG_STD_NO_ACTION

BSTUN-6-RECONNECT

6-Information

PHDR: reconnect from peer [chars]

A remote peer reestablished a connection to this router.

-

LOG_STD_NO_ACTION

BSTUN-2-NOBUF

2-Critical

Interface [chars] no buffer available to [chars]

A memory shortage existed at the time that the configuration command\n\ was issued. This condition is rare and under normal conditions\n\ temporary.

-

"Reconfigure the BSTUN group. If memory shortages persist call your\n\ technical support representative for assistance."

BSTUN-3-NOGRPDEF

3-Error

No bstun group defined on interface [chars]

An action was taken that requires the previous definition of a BSTUN\n\ group number.

-

"Make sure "encapsulation bstun" and the "bstun group" have been\n\ defined for the interface."

BSTUN-3-UNKPROTOEV

3-Error

Unknown protocol event [dec] on interface [chars]

An event passed to the BSTUN layer for processing could not\n\ be decoded.

-

"Perform a hard restart on the indicated interface."

BSTUN-6-PROCEXIT

6-Information

Process terminating. Due to signal [dec]. Subcode [dec]. Address [hec].

The BSTUN background process is terminating.

-

"If this message appears while you are unconfiguring BSTUN no action\n\ is required. Otherwise record all the displayed values and any other\n\ BSTUN error messages and contact your technical support\n\ representative."

BSTUN-3-NOPEER

3-Error

No peer configured to route frame with destination address [chars] bstun group [dec]

A BSTUN route has not been configured for the frame with a destination address.

-

"If this message appears while you are debugging bstun it indicates that no\n\ specific bstun route has been configured for the frames being received with\n\ the device address listed in the packet debug trace. You may choose to configure\n\ a bstun route or ignore this message."

BSTUN-3-IFNOTSETUP

3-Error

Could not setup interface for protocol [chars]

BSTUN was unable to start the interface for handling the specified protocol traffic.

-

"If this message appears while you are configuring BSTUN check for\n\ other system errors such as no available memory in the router or the interface\n\ shutting down. If no obvious problem can be detected record all the displayed\n\ values and any other BSTUN error messages and contact your technical support\n\ representative."

ASPP-3-NOTTY

3-Error

[chars]: Unable to set Rx/Tx tty async service hooks.

This message occurs only when ASP is configured. It\n\ indicates the serial interface using ASP is configured\n\ incorrectly or does not support asynchronous mode.

-

"Verify the correct hardware interface type is being used."

FTC_TRUNK-1-NOMEMORY

1-Alert

msgtxt_nomemory

The MPC860/PowerQUICC CPU was unable to access the memory it needs to carry out its functions. Here are some possible causes. The network is large requiring a lot of memory for routing tables and so on. The router configuration has many features enabled each of which require a certain amount of memory. A software error memory leak exists.

-

"Reduce system activity to ease the memory demand or upgrade to a larger memory configuration."

FTC_TRUNK-3-TOOMANY

3-Error

Cannot config more than [dec] ftc-trunks

When the operator enters the 'encap ftc-trunk' configuration command if there are already 4 interfaces configured for encap ftc-trunk this message is displayed to indicate that no more can be configured.

-

"Free one of the other interfaces first or if conditions warrant upgrade to a larger configuration with more interfaces."

FTC_TRUNK-1-RELOAD

1-Alert

Must reload to config Interface [chars] as ftc-trunk again

If the operator first configures an interface to 'encapsulation ftc-trunk' then re-configures it later to some other encapsulation such as HDLC then attempts to re-configure it again to 'encap ftc-trunk' then this error messages is displayed to notify the operator that the 'reload' command must be entered first before attempting to configure the interface to 'encap ftc-trunk' again.

-

"Issue the 'reload' command."

FTC_TRUNK-3-TOOMANY_SESSION

3-Error

Cannot config more than [dec] session-trunks

When the operator enters the 'encap ftc-trunk' configuration command if there are already 4 interfaces configured for encap ftc-trunk then the message is displayed to indicate that no more can be configured.

-

"Free one of the existing interfaces before trying again or if conditions warrant upgrade to a larger configuration."

FTC_TRUNK-3-CID_IN_USE

3-Error

[chars] connection-id [dec] is busy try other cid

When setting up a new session-trunk if the operator attempts to use a connection-ID that is already assigned and in-use then the error message is displayed to indicate that the selected connection-id cannot be used for this session-trunk.

-

"Try again with a connection-ID which is not already in use."

SPARC-3-DOWN

3-Error

SPARC process is not responding [chars]

Failed to init calltracker record table.

CallTracker

"Disable calltracker first [no calltracker enable] enable it again."

CALLTRKR-3-NO_MEM

3-Error

Memory allocation failed for CT [chars] [dec] bytes

Calltracker couldn't allocate new record due to no free memory.

CallTracker

"Disable calltracker [no calltracker enable]. Run show memory to\n\ find out where is the memory been allocated."

CALLTRKR-3-PROC

3-Error

can't spawn [chars]

Couldn't spawn calltracker process.

CallTracker

"Disable calltracker first [no calltracker enable] enable it again."

CALLTRKR-3-PRINT_BUFFER

3-Error

calltrkr cli print buffer [chars]

calltrkr cli internal print buffer overflow.

Calltracker

"Stop to using calltrkr show commands call TAC to report the problem"

CALLTRKR-6-CALL_RECORD

6-Information

[chars]

Terse CallTracker Call Record

CallTracker

LOG_STD_NO_ACTION

CALLTRKR-6-MODEM_CALL_REC

6-Information

[chars]

Modem Verbose CallTracker Call Record

CallTracker

LOG_STD_NO_ACTION

CALLTRKR-6-MODEM_LINE_CALL_REC

6-Information

[chars]

Modem Line Verbose CallTracker Call Record

CallTracker

LOG_STD_NO_ACTION

CALLTRKR-6-MODEM_INFO_CALL_REC

6-Information

[chars]

Modem Information Verbose CallTracker Call Record

CallTracker

LOG_STD_NO_ACTION

CALLTRKR-6-MODEM_NEG_CALL_REC

6-Information

[chars]

Modem Negotiation Verbose CallTracker Call Record

CallTracker

LOG_STD_NO_ACTION

CALLTRKR-3-CALL_REC_ERROR

3-Error

[chars]

Record Generated Exceeded Syslog Capability

CallTracker

LOG_STD_NO_ACTION

SLB-4-IF_REMOVED

4-Warning

Access interface removed: [chars] [chars] being set to outofservice.

An interface being referenced in slb access configuration has been removed. The vserver or firewallfarms referencing this interface will brought outofservice.

slb

LOG_STD_RECUR_ACTION

SLB-4-VRF_REMOVED

4-Warning

Access VRF removed: [chars] [chars] being set to outofservice. Access VRF \n\ configuration has been removed.

An VRF being referenced in slb access configuration has been\n\ removed. The vserver or firewallfarms referencing this VRF will \n\ brought outofservice. The access VRF configuration will be removed.

slb

LOG_STD_RECUR_ACTION

SLB-4-UNEXPECTED

4-Warning

Unexpected error: [chars]

An unexpected error occurred while performing SLB operation

slb

LOG_STD_RECUR_ACTION

SLB-6-REAL

6-Information

Real [chars] [chars] has changed state to [chars]

Informational message whenever a real server changes its state to/from OPERATIONAL: possible causes might be e.g. testing probe testing maxconns

slb

LOG_STD_NO_ACTION

SLB-4-PROBE

4-Warning

Probe [chars] for [inet]:[dec] [chars]

An error occured during SLB probe operation

slb

LOG_STD_REDUCE_ACTION

SLB-4-CF

4-Warning

Unexpected error: [chars]

An unexpected error occurred in SLB slave replication

slb

LOG_STD_RECUR_ACTION

SLB-4-CF_NUM

4-Warning

Unexpected error: [chars] [dec]

An unexpected error occurred in SLB slave replication

slb

LOG_STD_RECUR_ACTION

SLB-4-CF_BULK

4-Warning

[chars]

An unexpected error occurred in SLB slave replication bulk sync

slb

LOG_STD_RECUR_ACTION

SLB-4-CF_RATE

4-Warning

Overrun of SLB's slave replication rate some SLB objects may not be synchronized.

Due to a high connection rate SLB was unable to replicate all objects.

slb

LOG_STD_RECUR_ACTION

SLB-4-CF_IPC

4-Warning

Slave replication messages are creating a backlog in IPC. Some SLB objects may not be synchronized.

Due to IPC resource contention SLB was unable to replicate all objects.

slb

LOG_STD_RECUR_ACTION

CSM_SLB-4-INVALIDID

4-Warning

Module [dec] invalid ID: [chars]

The entity identified does not exist.

laminar

LOG_STD_NO_ACTION

CSM_SLB-4-DUPLICATEID

4-Warning

Module [dec] duplicate ID: [chars]

Same ID was used to create multiple entities.

laminar

LOG_STD_NO_ACTION

CSM_SLB-3-OUTOFMEM

3-Error

Module [dec] memory error: [chars]

Out of memory condition while downloading SLB configurations onto CSM card.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-4-REGEXMEM

4-Warning

Module [dec] regular expression memory error: [chars]

A lookup table does not contain enough space to store the configured URL and COOKIE regular expressions. Use 'show ip slb memory' to determine which virtual servers were unable to be configured because of

laminar

LOG_STD_NO_ACTION

CSM_SLB-4-ERRPARSING

4-Warning

Module [dec] configuration warning: [chars]

Syntax error in a URL or COOKIE regular expression in SLB configuration.

laminar

LOG_STD_NO_ACTION

CSM_SLB-4-PROBECONFIG

4-Warning

Module [dec] probe configuration error: [chars]

Health probe configuration failed.

laminar

LOG_STD_NO_ACTION

CSM_SLB-4-ARPCONFIG

4-Warning

Module [dec] ARP configuration error: [chars]

Error creating or removing a static ARP route.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-6-RSERVERSTATE

6-Information

Module [dec] server state changed: [chars]

A real server changed states failed or recovered. Possible causes might be configuration changes arp checks or health probes.

laminar

LOG_STD_NO_ACTION

CSM_SLB-6-GATEWAYSTATE

6-Information

Module [dec] gateway state changed: [chars]

A gateway changed states.

laminar

LOG_STD_NO_ACTION

CSM_SLB-3-UNEXPECTED

3-Error

Module [dec] unexpected error: [chars]

An unexpected error condition occurred on the CSM-SLB card while performing Server Load Balancing.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-3-REDUNDANCY

3-Error

Module [dec] FT error: [chars]

An error occurred in CSM-SLB fault tolerance.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-4-REDUNDANCY_WARN

4-Warning

Module [dec] FT warning: [chars]

Some possibly undesired event occurred in CSM-SLB fault tolerance.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-6-REDUNDANCY_INFO

6-Information

Module [dec] FT info: [chars]

Some event occurred in CSM-SLB fault tolerance.

laminar

LOG_STD_NO_ACTION

CSM_SLB-3-ERROR

3-Error

Module [dec] error: [chars]

An error occurred in a CSM-SLB module.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-4-WARNING

4-Warning

Module [dec] warning: [chars]

Some possibly undesired event occurred in a CSM-SLB module.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-6-INFO

6-Information

Module [dec] info: [chars]

Some event occurred in a CSM-SLB module.

laminar

LOG_STD_NO_ACTION

CSM_SLB-4-TOPOLOGY

4-Warning

Module [dec] warning: [chars]

There may be a problem with your network topology or configuration.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-3-SCRIPT

3-Error

Module [dec] script error: [chars]

An error occurred in a CSM-SLB script.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-4-SCRIPT_WARN

4-Warning

Module [dec] script warning: [chars]

Some possibly undesired event occurred in CSM-SLB scripting.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-6-SCRIPT_INFO

6-Information

Module [dec] script info: [chars]

Some event occurred in CSM-SLB scripting.

laminar

LOG_STD_NO_ACTION

CSM_SLB-3-RELOAD

3-Error

Module [dec] configuration reload failed: [chars]

Configuration reload of the CSM-SLB card failed.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-3-VERMISMATCH

3-Error

Module [dec] image version mismatch RP = [chars] CSM = [chars]: [chars]

Router image and CSM-SLB image do not correspond.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-4-VERWILDCARD

4-Warning

Received CSM-SLB module version wildcard on slot [dec]. Supervisor has version [dec].

User issued a command from the linecard to bypass the safeguard against module version mismatch. As a result configuration may fail.

laminar

LOG_STD_NO_ACTION

CSM_SLB-3-PORTCHANNEL

3-Error

Portchannel allocation failed for module [dec].

Unable to allocate enough portchannel groups for CSM-SLB card.

laminar

LOG_STD_RECUR_ACTION

CSM_SLB-3-IDB_ERROR

3-Error

Unknown error occurred while configuring IDB for CSM-SLB module: [chars].

Unable to configure data path for CSM-SLB card.

laminar

LOG_STD_RECUR_ACTION

SLB_DFP-4-KEEP_ALV

4-Warning

Agent [inet]:[dec] - Have not received keep alive

The system has not received a keepalive message from the SLB DFP Agent.

slb

"Verify that the DFP Agent is reachable via " "ping or traceroute. Verify that the DFP Agent on the server is running." LOG_STD_RECUR_ACTION

SLB_DFP-4-UKN_CON

4-Warning

Agent [inet]:[dec] - Unknown connection state [dec]

Unknown connection state processing SLB DFP timer

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-BAD_SEND

4-Warning

Agent [inet]:[dec] - Send failed

An attempt to send a message to the SLB DFP Agent has failed.

slb

"Verify that the DFP Agent is reachable via " "ping or traceroute. Verify that the DFP Agent on the server is running." LOG_STD_RECUR_ACTION

SLB_DFP-4-SOCK_OPN

4-Warning

Agent [inet]:[dec] - Socket alreay open

The system tried to open Socket to SLB DFP Agent that is already open.

slb

"If the problem persists unconfigure and " "reconfigure SLB DFP. " LOG_STD_RECUR_ACTION

SLB_DFP-4-CON_FAIL

4-Warning

Agent [inet]:[dec] - Socket_connect failed

Socket_connect to SLB DFP Agent failed

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-SOCK_ERR

4-Warning

Agent [inet]:[dec] - Socket_recv error [dec]

Socket_recv error receiving message from SLB DFP Agent

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-READ_ERR

4-Warning

Agent [inet]:[dec] - Too many read errors

Too many errors reading message header from SLB DFP Agent

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-BAD_LEN

4-Warning

Agent [inet]:[dec] - Invalid message length - [dec]

Too many errors reading message header from SLB DFP Agent

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-BIG_MSG

4-Warning

Agent [inet]:[dec] - Message length [dec] too big

A message from the SLB DFP Agent exceeds the allowable maximum size.

slb

"A message exceeding allowable maximum size can " "be caused by a connection error between DFP Manager and Agent. Try to " "restart DFP Agent by unconfiguring and reconfiguring it to see if it fixes "

SLB_DFP-4-NO_PARSE

4-Warning

Agent [inet]:[dec] - Could not parse message

Could not parse message from SLB DFP Agent

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-BAD_MSG

4-Warning

Agent [inet]:[dec] - Unknown message type [dec] vector [dec]

An unknown message type received from SLB DFP Agent

slb

"An unknown message can be caused by a connection " "error between DFP Manager and Agent. Try to restart DFP Agent by unconfiguring " "and reconfiguring it to see if it fixes the connection error."

SLB_DFP-4-BIG_VEC

4-Warning

Agent [inet]:[dec] - Message type [dec] vector [dec] too big

A message from the SLB DFP Agent exceeds the allowable maximum size.

slb

"A message exceeding allowable maximum size can " "be caused by a connection error between DFP Manager and Agent. Try to " "restart DFP Agent by unconfiguring and reconfiguring it to see if it fixes "

SLB_DFP-4-UNK_TYPE

4-Warning

Agent [inet]:[dec] - Unknown message type [dec]

Message from SLB DFP Agent has unknown type

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-UNEXPECTED

4-Warning

Unexpected error: [chars]

An unexpected error occurred while performing SLB DFP operation

slb

LOG_STD_RECUR_ACTION

SLB_DFP-4-RECONN_MGR

4-Warning

Manager [inet] is reconnecting

The SLB Manager is reconnecting without disconnecting

slb

LOG_STD_RECUR_ACTION

CASA-3-BADVER

3-Error

Incoming packet is CASA v[dec] this router is v[dec]

A packet was received for the wrong version of CASA

casa

"Verify that all CASA devices are running the same version \n\of the protocol"

CASA-2-NOMEM

2-Critical

Out of memory: [chars]\n

CASA failed to allocate memory.

casa

LOG_STD_REDUCE_ACTION

CASA-4-BADMSG

4-Warning

Message parsing error: [chars]

Failed to parse an incoming packet

casa

"If this message is occurring repeatedly enable 'debug ip casa error'\n\and record the output call your Cisco technical support representative\n\and provide the gathered information."

CASA-4-SECURITY_FAIL

4-Warning

[chars] security information in CASA packet.

Security check failed.

casa

"Make sure all CASA systems are configured with the same password."

CASA-4-UNEXPECTED

4-Warning

Unexpected error: [chars]

An unexpected error occurred while performing CASA operation

casa

LOG_STD_RECUR_ACTION

CASA-4-WARNING

4-Warning

Unexpected condition: [chars]

An unexpected condition was detected while performing CASA operation

casa

LOG_STD_RECUR_ACTION

CASA-4-PORTCHANGE

4-Warning

Wildcard overlap: [chars]

A CASA wildcard received on one port has been overwritten \n\by a service manager sending to another port. This message may appear \n\once if you are migrating your service to a new forwarding-agent port\n\if it recurs it could indicate a configuration problem.

casa

LOG_STD_RECUR_ACTION

NET_SERV-4-UNEXPECTED

4-Warning

Unexpected error: [chars]

An unexpected error occurred while performing a services timer operation

slb

LOG_STD_RECUR_ACTION

NET_SERV-4-WARNING

4-Warning

Unexpected condition: [chars]

An unexpected condition was detected while performing a services timer\n\ operation

slb

LOG_STD_RECUR_ACTION

SLB_KAP-3-BIND_FAIL

3-Error

SLB Keep Alive Application Protocol Socket_bind failed for Port:[dec]

SLB Keep Alive Application Protocol process attempts to bind a socket port failed

slb

LOG_STD_RECUR_ACTION

SLB_KAP-4-UNEXPECTED

4-Warning

Unexpected error: [chars]

An unexpected error occurred while performing SLB Keep Alive Application Protocol operation

slb

LOG_STD_RECUR_ACTION

FASTBLK-4-QUEUE_ERR

4-Warning

Fastblk queue error: [chars]

An unexpected error occurred while performing a fastblk memory\n\queue operation

slb

LOG_STD_RECUR_ACTION

FASTBLK-4-GROW_ERR

4-Warning

Fastblk pool growth error: [chars]

An unexpected error occurred while performing a fastblk memory\n\pool growth operation

slb

LOG_STD_RECUR_ACTION

FASTBLK-4-SHRINK_ERR

4-Warning

Fastblk pool shrink error: [chars]

An unexpected error occurred while performing a fastblk memory\n\pool shrink operation

slb

LOG_STD_RECUR_ACTION

FASTBLK-4-DEALLOC_ERR

4-Warning

Fastblk deallocation error: [chars]

An unexpected error occurred while performing a fastblk memory\n\deallocation operation

slb

LOG_STD_RECUR_ACTION

FASTBLK-4-CREATE_ERR

4-Warning

Fastblk pool creation error: [chars]

An unexpected error occurred while performing a fastblk memory\n\pool creation operation

slb

LOG_STD_RECUR_ACTION

FASTBLK-4-WARNING

4-Warning

Unexpected condition: [chars]

An unexpected condition was detected while performing a fastblk memory\n\operation

slb

LOG_STD_RECUR_ACTION

SLBSCPU-3-NOREQ

3-Error

Failed to get request packet for ICC

Error occurred during communication between SLB CPU

slb

LOG_STD_RECUR_ACTION

SLBSCPU-3-NORESP

3-Error

Did not receive ICC response

Error occurred during communication between SLB CPU

slb

LOG_STD_RECUR_ACTION

SLBSCPU-3-NOPROC

3-Error

Cannot create SLB SCPU Process

Error occurred during initialization of SLB process on SLB CPU

slb

LOG_STD_RECUR_ACTION

SLBSCPU-3-NOCFGDWLD

3-Error

Unable to request initial config download from main CPU.

After initialization SLB CPU requests main CPU to send configuration readfrom NVRAM. This message is generated when a failure occurs in communication.

slb

LOG_STD_RECUR_ACTION

SLBSCPU-6-CFGDWLD

6-Information

Request [dec] initial config download from main CPU.

After initialization SLB CPU requests main CPU to send configuration readfrom NVRAM. This message is indicates a request was sent.

slb

""

SLBSCPU-3-BADTYPE

3-Error

Unknown type of indication [hec]

Microcode is sending bad indication type.

slb

LOG_STD_RECUR_ACTION

CDP_PD-4-POWER_OK

4-Warning

[chars] - [chars] inline power source on port [chars]

System is supplied with sufficient power.

-

"No recommended action."

CDP_PD-2-POWER_LOW

2-Critical

[chars] - [chars] [chars] [enet] on port [chars]

System is not supplied with its maximum power

-

"Reconfigure or replace the source of inline power to get maximum power."

CES-2-INTERNAL_CRITICAL

2-Critical

[chars]

The CES subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

CES-3-INTERNAL_ERROR

3-Error

[chars]

The CES subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

CES-4-INTERNAL_WARNING

4-Warning

[chars]

The CES subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

EXAR7503-3-EXAR7503_PROG_ERR

3-Error

Exar7503 LIU programming error: [chars]

Error present while read/write to Exar LIU

osm-ct3 for CT3 osm-t3e3 for T3/E3

LOG_STD_ACTION

EXAR7503-3-EXAR7503_INIT_ERR

3-Error

Exar7503 LIU channel:[dec] init error

Error present during Exar LIU initialization

osm-ct3 for CT3 osm-t3e3 for T3/E3

LOG_STD_ACTION

EXAR7503-3-EXAR7503_NUM_ERR

3-Error

INvalid Exar7503 LIU number error: [chars]

Error present while inavlid EXAR number present

osm-ct3 for CT3 osm-t3e3 for T3/E3

LOG_STD_ACTION

GULF2488-3-INITERR

3-Error

gulf2488 chip initialization failed errcode=[dec]: [chars]

required resources unavailable.

osm-choc-ds3

"Reinsert the linecard. If still fails do\n\ 'test cwtlc show seeprom red' swap hardware and\n\ Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GULF2488-3-PROVERR

3-Error

gulf2488 channel provisioning failed slice:[dec] ch:[dec]: [chars]

required resources unavailable.

osm-choc-ds3

LOG_STD_ACTION

GULF2488-3-UNPROVERR

3-Error

gulf2488 channel unprovisioning failed slice:[dec] ch:[dec]: [chars]

required resources unavailable.

osm-choc-ds3

LOG_STD_ACTION

SPE4X155-3-INITERR

3-Error

Chip initialization failed errcode=[dec]: [chars]

required resources unavailable.

osm-choc-ds0

"Reinsert the linecard. If still fails do\n\ 'test cwtlc show seeprom red' swap hardware and\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative."

SPE4X155-3-PDDBNULL

3-Error

Pointer to device structure is 0

Software error occured.

osm-choc-ds0

LOG_STD_ACTION

SPE4X155-3-PDDBERROR

3-Error

Pointer to device structure is invalid

Software error occured.

osm-choc-ds0

LOG_STD_ACTION

FRDM336-3-INITERR

3-Error

FRDM336 chip initialization failed errcode=[dec]: [chars]

Required resources to initialize the ASIC in Linecard unavailable. This is normally due to hardware issue

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Reinsert the linecard. If still fails " "swap hardware and LOG_STD_SH_TECH_ACTION"

FRDM336-3-SET_SPE_ERR

3-Error

FRDM336 setting configuration of SPE SBI no:[dec] SPE no:[dec] to [dec] failed

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-SET_TRIB_ERR

3-Error

FRDM336 setting configuration of tributary SBI no:[dec] SPE no:[dec] TRIB no:[dec] to [dec] failed errcode=[dec]: [chars]

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-TRIB_ENAB_DIS_ERR

3-Error

FRDM336 [chars] tributary SBI no:[dec] SPE no:[dec] TRIB no:[dec] failed

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-PROVERR

3-Error

FRDM336 Channel provisioning SBI no:[dec] SPE no:[dec] TRIB no:[dec] HDLC channel no:[dec] failed errcode=[dec]: [chars]

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in " "Linecard and RP"

FRDM336-3-SET_CHANPARAM_ERR

3-Error

FRDM336 setting parameters of a Channel failed HDLC channel no:[dec]

-

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in " "Linecard and RP"

FRDM336-3-POLLTO

3-Error

FRDM336 indirect poll timeout. base addr:[hex] offset:[hex] value:[hex] mask:[hex] delay:[hex]

Not able to access a register in the ASIC of Linecard this is normally hardware problem

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

LOG_STD_SH_TECH_ACTION

FRDM336-3-CC_RESEQ_FIFO_ACT_NOT_CLEAR

3-Error

FRDM336 base addr 0x[hec]: Removing CI0x[hec] of channel

Encountered an error in the ASIC of line card while unprovisioning a channel or Multilink interface.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' " "in Linecard and RP"

FRDM336-3-RHDL_TAVAIL_NOT_CLEAR

3-Error

FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec]

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-NCHUNKSNONZERO

3-Error

FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec]

Encountered an error in the ASIC of line card This mostly occurs while unprovisioning a channel or shuting interface.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-NCHUNKSNONZERO_CC_RESEQ_FIFO_ACT_SET

3-Error

FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec]

Encountered an error in the ASIC of line card This mostly occurs while unprovisioning a channel or shuting interface.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-THDL_AVAIL_NOT_CLEAR

3-Error

FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec]

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION

FRDM336-3-EQM_SIZE_NOT_ZERO

3-Error

HDLC%04d : %#010x %#010x %#010x %#010x

Encountered an error while configuring or unconfiguring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP"

FRDM336-6-EQM_ML_INFO

6-Information

ML%04d : %#010x %#010x %#010x %#010x

Multilink information

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"No action is required"

FRDM336-3-DLCICOSRANGE

3-Error

DLCICOS0x[hec] not within range

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP"

FRDM336-3-DEFAULTCI

3-Error

Unexpected default CI for channel 0x[hec]

Encountered an error while configuring an ASIC in the Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP"

FRDM336-3-BUNDLEEXIST

3-Error

Unexpected bundle0x[hec] present in freedm

Encountered an error while provisioning a bundle

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-PDDBNULL

3-Error

Device data block null

Encountered an error while accessing an ASIC in Linecard

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-BUNDLERANGE

3-Error

bundle0x[hec] not within range

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-5-NOBUNDLEPRESENT

5-Notice

bundle0x[hec] not present in freedm

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-ANYPHYALLOCFAILED

3-Error

Anyphy allocation failed for [chars]

Encountered an error while configuring the ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-INVALIDANYPHY

3-Error

Anyphy0x[hec] number is not in range

Encountered an error while configuring the ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP " "'show platform multilink' in Linecard"

FRDM336-3-NOANYPHYALLOCATED

3-Error

No Anyphy number for channel=[dec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-CIALLOCFAILED

3-Error

CI allocation failure for tag=[dec] dlciCos=[dec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-NOCIALLOCATED

3-Error

No CI number for tag=[dec] dlciCos=[dec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-INVALIDCI

3-Error

Either CI0x[hec] range not ok or not allocated

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-CITAGMISMATCH

3-Error

CI0x[hec] does not belong to tag0x[hec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-LLAPI_PROVERR

3-Error

FRDM336 base addr 0x[hec]: Channel provisioning SBI no:[dec] SPE no:[dec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-LLINT_TSMSKUSEERR

3-Error

FRDM336 base addr 0x[hec]: TS mask in use SBI no:[dec] SPE no:[dec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

FRDM336-3-LLINT_DET_TSMSKUSEERR

3-Error

FRDM336 base addr 0x[hec]: TS mask in use SBI no:[dec] SPE no:[dec]

Encountered an error while configuring an ASIC in Linecard.

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0

"'show controller' in Linecard and RP" "'show platform multilink' in Linecard"

TEMUX84-3-SBIWAITERR

3-Error

temux84 SBI indirect access failed [chars]

hardware busy bit not cleared

osm-ct3 for CT3osm-choc-ds0 for CHOC-12

LOG_STD_ACTION

TEMUX84-3-BSWAITERR

3-Error

temux84 Byte-Sync indirect access failed [chars]

hardware busy bit not cleared

osm-ct3 for CT3osm-choc-ds0 for CHOC-12

LOG_STD_ACTION

TEMUX84-3-RTTBWAITERR

3-Error

temux84 RTTB indirect access failed [chars]

hardware busy bit not cleared

osm-ct3 for CT3osm-choc-ds0 for CHOC-12

LOG_STD_ACTION

TEMUX84-3-T1E1WAITERR

3-Error

temux84 T1E1 indirect access failed [chars]

hardware busy bit not cleared

osm-ct3 for CT3osm-choc-ds0 for CHOC-12

LOG_STD_ACTION

TEMUX84-3-T3E3PMONERR

3-Error

temux84 T3E3 PMON update failed [chars]

JIB3-US FA interrupt

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support"

INTR_MGR-3-INTR

3-Error

[chars] [chars]

The specified interrupt event has been detected.

-

"The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION

INTR_MGR-3-BURST

3-Error

[chars] [chars] [[dec]]

A burst of hardware interrupts of the type indicated has occurred.

-

"The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION

INTR_MGR-3-MAXBURST

3-Error

[chars] [chars] [[dec]]

The specified hardware interrupt has exceeded the maximum allowed number of bursts.

-

"The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION

SPE2488-3-INITERR

3-Error

spe2488 chip initialization failed errcode=[dec]: [chars]

required resources unavailable.

osm-choc-ds3

"Reinsert the linecard. If still fails do\n\ 'test cwtlc show seeprom red' swap hardware and\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative."

SPE2488-3-RESETERR

3-Error

spe2488 chip reset failed errcode=[dec]: [chars]

required resources unavailable.

osm-choc-ds3

"REinsert the linecard.\n\ Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SPE2488-3-PROVERR

3-Error

spe2488 channel provisioning failed slice:[dec] ch:[dec]: [chars]

required resources unavailable.

osm-choc-ds3

LOG_STD_ACTION

SPE2488-3-UNPROVERR

3-Error

spe2488 channel unprovisioning failed slice:[dec] ch:[dec]: [chars]

required resources unavailable.

osm-choc-ds3

LOG_STD_ACTION

SPE2488-3-PARAERR

3-Error

spe2488 API failed errcode=[dec]: p1=[dec] p2=[dec] [chars]

wrong parameters passed in when calling an API

osm-choc-ds3

LOG_STD_ACTION

SPE2488-3-POLLTO

3-Error

spe2488 indirect poll timeout. addr:[hex]

hardware problem

osm-choc-ds3

LOG_STD_ACTION

DS_PHY-2-UPX_SPI_ERR

2-Critical

[chars]

-

-

-

DS_PHY-3-UPX_UPGRADE_ERROR

3-Error

check/upgrade failure - [chars]

upconverter - can't check version or upgrade

ubr10k-sw

"check type of upconverter"

DS_PHY-3-RM_JIB_IF_ERROR

3-Error

Remora hw reset failure - [chars]

Cannot hw reset DS PHY

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support"

DLC-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

An internal software error occurred.

-

LOG_STD_ACTION

DLC-2-NOMEMORY

2-Critical

no memory for [chars]

There was not enough free memory to complete the operation.

-

LOG_STD_ACTION

DLC-3-WPUTERR

3-Error

unknown port type [hec]

An internal software error occurred.

-

LOG_STD_ACTION

DLC-3-INVPCEP

3-Error

Close Station invalid P_CEP

An internal software error occurred.

-

LOG_STD_ACTION

CLS-3-CLSFAIL

3-Error

CLS: Assertion failed: [chars]

A software or hardware error occurred.

-

LOG_STD_ACTION

CLS-3-CLSMSG

3-Error

[chars]

A software error detected while manipulating CLSIMsg objects.

-

LOG_STD_ACTION

CLS-3-BOGUSOP

3-Error

Unknown CLS verb for [chars] context DlcOpcodeT=%04x

A bad opcode was generated by the DLC for the STN or CEP.

-

LOG_STD_ACTION

UBR900-4-FAILED_TO_ACQUIRE_SYNC

4-Warning

T01.0 Failed to acquire QAM/QPSK symbol timing. Error stats? Retry [dec]'s

Failed to acquire QAM/QPSK symbol timing\n

-

""

UBR900-4-FAILED_TO_ACQUIRE_FEC

4-Warning

T02.0 Failed to acquire FEC framing. Error stats? Retry [dec]'s [dec] of bad frames

Failed to acquire FEC framing

-

""

UBR900-4-FAILED_TO_ACQUIRE_MPEG2

4-Warning

T2.1 Acquired FEC framing. Failed to acquire MPEG2 Sync. Retry [dec]`s

Acquired FEC framing. Failed to acquire MPEG2 sync.

-

""

UBR900-4-FAILED_TO_ACQUIRE_MAC_FRAMING

4-Warning

T03.0 Failed to acquire MAC framing. Error stats? Retry [dec]'s [dec] of bad frames

-

-

""

UBR900-4-FAILED_TO_RECEIVE_SYNC

4-Warning

T04.0 Failed to Receive MAC SYNC frame within time-out period

Failed to Receive MAC SYNC frame within time-out period

-

""

UBR900-3-RESET_LOSS_OF_SYNC

3-Error

T05.0 Loss of Sync. Missed 5 in a row after having SYNCd at one time

Cable Interface Reset due to loss of sync\n

-

""

UBR900-4-NO_UCD_RCVD

4-Warning

U01.0 No UCD's received. Time-out

No UCD's Received. Time-out

-

""

UBR900-4-INVALID_UCD

4-Warning

U02.0 UCD invalid or channel unusable

Invalid UCD or channel unusable

-

""

UBR900-4-VALID_UCD_NO_SYNC

4-Warning

U03.0 UCD valid But no SYNC received. TIMED OUT.

UCD valid But not SYNC received. TIMED OUT.

-

""

UBR900-4-VALID_UCD_AND_SYNC_NO_MAPS

4-Warning

U04.0 UCD and SYNC are valid No MAPS for THIS channel

UCD and SYNC are valid No MAPS for THIS channel

-

""

UBR900-4-UCD_INVALID_OR_OUT_OF_ORDER_CCC

4-Warning

U05.0 UCD received with invalid or out of order Configuration Change Count

UCD received with invalid or out of order Configuration Change Count

-

""

UBR900-4-US_CHANNEL_PARM_NOT_SET

4-Warning

U06.0 US Channel wide parameters not set before Burst Descriptors

US Channel wide parameters not set before Burst Descriptors

-

""

UBR900-4-MAP_ARRIVED_TOO_LATE

4-Warning

M01.0 A transmit opportunity was missed because the MAP arrived too late

A transmit opportunity was missed because the MAP arrived too late

-

""

UBR900-3-RESET_T2_EXPIRED

3-Error

R01.0 No Maintenance Broadcasts for Ranging opportunities received T2 timeout

Cable Interface Reset due to t2 timeout\n

-

""

UBR900-3-RESET_T4_EXPIRED

3-Error

R04.0 Received Response to Broadcast Maintenance Request But no Unicast Maintenance opportunities received. T4 timeout.

Cable Interface Reset due to t4 timeout\n

-

""

UBR900-3-T3_TIMEOUT_I

3-Error

R02.0 No Ranging Response received T3 timeout

t3 timeout\n

-

""

UBR900-3-RESET_T3_RETRIES_EXHAUSTED

3-Error

R03.0 Ranging Request Retries exhausted

Cable Interface Reset due to t3 timeout\n

-

""

UBR900-3-T3_TIMEOUT_II

3-Error

R05.0 Started Unicast Maintenance Ranging no Response received. T3 time-out.

Cable Interface Reset due to t3 timeout\n

-

""

UBR900-3-T3_RETRIES_EXHAUSTED_II

3-Error

R06.0 Started Unicast Maintenance Ranging no Response received. T3 time-out.

Cable Interface Reset due to t3 timeout\n

-

""

UBR900-4-REINIT_MAC

4-Warning

R07.0 Unicast Ranging Received Abort Response. Reinitializing MAC.

Unicast Ranging Received Abort Response. Reinitializing MAC.

-

""

UBR900-4-UCC_REQ_INVALID

4-Warning

C01.0 UCC-REQ received with invalid or out of range US Channel ID.

UCC-REQ received with invalid or out of range US Channel ID

-

""

UBR900-4-UNBALE_TO_TX_UCC_RSP

4-Warning

C02.0 UCC-REQ received unable to send UCC-RSP no TX opportunity.

UCC-REQ received unable to send UCC-RSP no TX opportunity.

-

""

UBR900-6-NO_DHCP_OFFER

6-Information

D01.0 Discover sent no offer received No available DHCP Server

D01.0 Discover sent no offer received No available DHCP Server

-

""

UBR900-6-NO_DHCP_RESPONSE

6-Information

D02.0 Request sent no Response

Request sent no Response

-

""

UBR900-4-DHCP_REQ_INFO_NOT_SUPPORTED

4-Warning

D03.0 Requested Info not supported

Requested info not supported

-

""

UBR900-4-DHCP_RSP_OUT_OF_SPEC

4-Warning

D03.1 DHCP response doesn't contain ALL the valid fields as described in the RF spec Appendix C.1

response doesn't contain ALL the valid fields as described in the RF spec Appendix C.1

-

""

UBR900-4-INVALID_TOD

4-Warning

D04.0 Time of Day none set or invalid data

Time of Day none set or invalid data

-

""

UBR900-4-TOD_NO_RSP

4-Warning

D04.1 Time of Day request sent no Response received

Time of Day request sent no Response received

-

""

UBR900-4-TOD_RSP_INVALID

4-Warning

D04.2 Time of Day Response received but invalid data/format

Time of Day Response received but invalid data/format

-

""

UBR900-4-TFTP_NO_RSP

4-Warning

D05.0 TFTP Request sent No Response/No Server.

TFTP Request sent No Response/No Server

-

""

UBR900-4-TFTP_RQ_FAILED_1

4-Warning

D06.0 TFTP Request Failed configuration file NOT FOUND

TFTP Request Failed configuration file NOT FOUND

-

""

UBR900-4-TFTP_FAILED_2

4-Warning

D07.0 TFTP Request Failed OUT OF ORDER packets

TFTP Request Failed OUT OF ORDER packets

-

""

UBR900-4-TFTP_FAILED_3

4-Warning

D08.0 TFTP complete but failed Message Integrity CheckMIC

TFTP complete but failed Message Integrity CheckMIC

-

""

UBR900-3-RESET_T6_RETRIES_EXHAUSTED

3-Error

Cable Interface Reset due to t6 timeout

Cable Interface Reset due to t6 timeout\n

-

""

UBR900-3-RESET_DHCP_WATCHDOG_EXPIRED

3-Error

Cable Interface Reset due to DHCP watchdog timer expiration

Cable Interface Reset due to dhcp watchdog timer expiration\n

-

""

UBR900-3-TOD_FAILED_TIMER_EXPIRED

3-Error

TOD failed but Cable Interface proceeding to operational state

TOD failed but Cable Interface proceeding to operational state\n

-

""

UBR900-3-RESET_PRIVACY_WATCHDOG_EXPIRED

3-Error

Cable Interface Reset due to privacy watchdog timer

Cable Interface Reset due to privacy watchdog timer expiration\n

-

""

UBR900-3-RESET_CONFIG_FILE_WATCHDOG_EXPIRED

3-Error

Cable Interface Reset due to config file watchdog timer

Cable Interface Reset due to config file watchdog timer expiration\n

-

""

UBR900-6-UNDEFINED_HDR_RECEIVED

6-Information

Mac Messages received with undefined header\n

Mac Messages received with undefined header\n

-

""

UBR900-6-IMAGE_UPGRADE_INTERRUPTED

6-Information

System Image Upgrade interrupted during transfer. Upgrade reinitiated\n

System Image Upgrade interrupted during transfer. Upgrade reinitiated\n

-

""

UBR900-6-IMAGE_UPGRADE_SUCCESSFUL

6-Information

System Image Upgrade Complete.

System Image Upgrade Complete.\n

-

""

UBR900-6-IMAGE_UPGRADE_INITIATED

6-Information

System Image Upgrade initiated

System Image Upgraded has been initiated.\n

-

""

UBR900-4-CORRUPT_SYSTEM_IMAGE

4-Warning

Modem System Image is corrupt. New image upgrade required

Modem System Image is corrupt. New image upgrade required\n

-

""

UBR900-4-CORRUPT_SYSTEM_IMAGE_UPGRADING

4-Warning

Modem System Image is corrupt. Image upgrade reinitiated.

Modem System Image is corrupt. Image upgrade reinitiated.\n

-

""

UBR900-6-IMAGE_UPGRADE_FAILED_TFTP

6-Information

System Image Upgrade FAILED due to excessive TFTP failures.\n

System Image Upgrade FAILED due to excessive TFTP failures.\n

-

""

UBR900-6-IMAGE_UPGRADE_FAILED_IMAGE_CHECK

6-Information

System Image Upgrade FAILED due to unrecognizable or corrupt image.\n

System Image Upgrade FAILED due to unrecognizable or corrupt image.\n

-

""

UBR900-6-IMAGE_UPSTREAM_POWER_HIGH

6-Information

Upstream Power required at modem registration near maximum\n

Upstream Power required at modem registration near maximum\n

-

""

UBR900-6-SYNC_LOST_AND_REACQUIRED

6-Information

Downstream Sync lock lost and reacquired before timeout expired\n

Downstream Sync lock lost and reacquired before timeout expired\n

-

""

UBR900-7-RNG_REQ_TRANSMITTED

7-Debug

Periodic ranging request message transmitted.

Periodic ranging message transmitted

-

""

UBR900-7-RNG_RSP_MSG_RCVD

7-Debug

Periodic ranging response message received.

Periodic ranging response message received

-

""

CM_MONITOR-5-DNS_START

5-Notice

Starting DNS process

A hardware or software error occurred.

-

LOG_STD_ACTION

CM_MONITOR-5-DNS_KILL

5-Notice

Terminating DNS process

A hardware or software error occurred.

-

LOG_STD_ACTION

CM_MONITOR-5-DNS_RESP

5-Notice

Sending DNS response to [inet] request was for [inet]

-

-

-

CMP-5-ADD

5-Notice

The Device is added to the cluster Cluster Name: [chars] CMDR IP Address [inet]

The device is added to the cluster

c2900-xl-cluster

LOG_STD_NO_ACTION

CMP-5-REMOVE

5-Notice

The Device is removed from the cluster Cluster Name: [chars]

The device is removed from the cluster

c2900-xl-cluster

LOG_STD_NO_ACTION

CMP-5-MEMBER_CONFIG_UPDATE

5-Notice

Received member configuration from member [dec]

Received member configuration

c2900-xl-cluster

LOG_STD_NO_ACTION

CMP-5-MGMT_VLAN_CHNG

5-Notice

The management vlan has been changed to [dec]

The management vlan has been changed

c2900-xl-cluster

LOG_STD_NO_ACTION

CMP-5-NBR_UPD_SIZE_TOO_BIG

5-Notice

Number of neighbors in neighbor update is [dec] maximum number of neighbors allowed in neighbor update is [dec]

The number of cluster neighbors in the clustering neighbor update packet exceeds the number of neighbors supported by the clustering module design

c2900-xl-cluster

LOG_STD_NO_ACTION

CMP-4-MEM_CMPIP_ADDR_CONFLICT

4-Warning

Conflict with CMP IP address [inet] Reissuing a new CMP IP address to member [dec]

The cluster commander found a conflict with the assigned CMP IP address of the member. A new unique CMP IP address is assigned to the member.

c2900-xl-cluster

"This is a warning message only. The commander already assigned a new unique address to the member. Please clear any open TCP connections on the member using 'clear tcp' command."

CWAN_RP-6-LC_PRESENT

6-Information

[chars] in slot [dec]

A WAN module was detected by the hardware.

-

LOG_STD_NO_ACTION

CWAN_RP-6-IMAGE_UPGRADE

6-Information

Bootflash image upgrade [chars] for slot [dec]/[dec][chars]

The bootflash image on the WAN module has been or is being\n\ automatically upgraded.

-

LOG_STD_NO_ACTION

CWAN_RP-6-QUIESCE_FAIL

6-Information

Quiesce failed for slot [dec]/[dec]

The RP failed to contact the WAN module during failover.\n\ The WAN module will be reset.

-

LOG_STD_NO_ACTION

CWAN_RP-6-UNQUIESCE_FAIL

6-Information

Unquiesce failed for slot [dec]/[dec]. Error = [dec]

The RP failed to unquiesce the WAN module. \n\ The WAN module will be reset.

-

show diagbus and show ipc status

CWAN_RP-3-RESET_FAIL

3-Error

The WAN module in slot [dec] failed even after several resets

The WAN module in the slot specified in the error \n\ message did not boot successfully even after multiple \n\ attempts.

-

LOG_STD_RECUR_ACTION

CWAN_RP-3-POWER_CYCLE

3-Error

Power cycling WAN module in slot [dec]/[dec]. [chars]

The WAN module is being power cycled.

-

LOG_STD_NO_ACTION

CWAN_RP-3-POWER_CYCLE_IMMINENT

3-Error

The WAN module in slot [dec]/[dec] will be power cycled in [dec] seconds.

The WAN module in the slot specified in the error message \n\ will be power cycled in the amount of time specified in the error \n\ message

-

LOG_STD_NO_ACTION

CWAN_RP-3-BOOTFAIL

3-Error

The WAN module in slot [dec]/[dec] failed to boot

The WAN module in the slot indicated in the error messages \n\ failed to boot and will be reset.

-

LOG_STD_RECUR_ACTION

CWAN_RP-3-KEEPFAIL

3-Error

The WAN module in slot [dec]/[dec] is not responding to keepalives

The WAN module was either reset or has crashed and will be reset.

-

LOG_STD_RECUR_ACTION

CWAN_RP-3-SCPALLOCFAIL

3-Error

Failed to allocate SCP packet [chars]

The RP failed to allocate a packet for communication with other\n\ slots in the chassis.

-

LOG_STD_RECUR_ACTION

CWAN_RP-3-HV_ALLOCFAIL

3-Error

[chars]: Failed to allocate a VLAN: [chars]

VLAN allocation failed for the stated reason.

-

"First power down any unused linecards. " "Next delete any unused interfaces/subinterfaces and " "any unused L2 VLANs from the VLAN database. " "Then wait for >3 minutes and retry."

CWAN_RP-3-IPCPORTFAIL

3-Error

Failed to open IPC port '[chars]' [chars] with error [chars]

The RP failed to open a port for communication with a WAN\n\ module.

-

LOG_STD_ACTION

CWAN_RP-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The RP failed to allocate a buffer for communication with a\n\ WAN module.

-

LOG_STD_ACTION

CWAN_RP-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The RP failed to send a message to a WAN module.

-

LOG_STD_ACTION

CWAN_RP-3-BAD_IFCOMTYPE

3-Error

Bad ifcom message type=[dec]

A WAN module passed down a message that the RP software\n\ was not prepared to handle.

-

LOG_STD_ACTION

CWAN_RP-3-FOREVER

3-Error

cmd [dec] to [chars] slot [dec]/[dec] took [dec] usecs done [hec]

A CCB command from the RP to a WAN module took longer than expected.

-

LOG_STD_ACTION

CWAN_RP-3-IFCFG_FOREVER

3-Error

to [chars] slot [dec]/[dec] took [dec] usecs ret_val %lu

A interface config command from the RP to a WAN module took \n\ longer than expected.

-

LOG_STD_ACTION

CWAN_RP-3-ERROR

3-Error

NULL

This message can take many forms. It provides information about a\n\ software error.

-

LOG_STD_ACTION

CWAN_RP-6-CARDRELOAD

6-Information

Module reloaded on slot [dec]/[dec]

The WAN module has booted.

-

LOG_STD_NO_ACTION

CWAN_RP-6-CARDRECONCILE

6-Information

Module type changed on slot [dec]/[dec] from [dec] to [dec]

The WAN module has booted and it has been detected that it is\n\ of a different type to the WAN module that was previously in\n\ this slot.

-

LOG_STD_NO_ACTION

CWAN_RP-3-LC_CRASHINFO

3-Error

[chars] copied onto RP bootflash

The WAN module has crashed and the crashinfo file has been\n\ copied onto the RP bootflash. The crashinfo filename indicates the\n\ module's slot. The file can be viewed using the\n\ <CmdBold>more<noCmdBold> command.

-

LOG_STD_ACTION

CWAN_RP-3-LC_CRASHINFO_BLOCKED

3-Error

Duplicate crashinfo upload from slot [dec]/[dec] blocked

The WAN module has crashed and the crashinfo was not saved because\n\ the WAN module has already crashed recently.

-

LOG_STD_ACTION

CWAN_RP-3-LC_CRASHINFO_NOSPACE

3-Error

Not enough space on RP bootflash for crashinfo from slot [dec]/[dec] [dec] bytes needed [dec] available

The WAN module has crashed and there is not enough space on the RP\n\ bootflash to store the crashinfo.

-

"Free up space on the RP's bootflash by using the\n\ <CmdBold>delete<noCmdBold> and <CmdBold>squeeze<noCmdBold>\n\ commands."

CWAN_RP-3-LC_CRASHINFO_IFSERR

3-Error

Error [chars] [chars]: [chars] [dec]

The WAN module has crashed and an error occured while trying to\n\ access the RP's bootflash to save the crashinfo.

-

LOG_STD_ACTION

CWAN_RP-3-LC_CRASHINFO_CORRUPT

3-Error

Verification of crashinfo from slot [dec]/[dec] failed

The WAN module has crashed and verification of the crashinfo it\n\ sent failed. The crashinfo has not been saved to RP bootflash.

-

LOG_STD_ACTION

CWAN_RP-3-LC_CRASHINFO_ERR

3-Error

Unexpected error while receiving crashinfo from slot [dec]/[dec]

The WAN module has crashed and an unexpected error occured while\n\ the crashinfo was being copied onto RP bootflash.

-

LOG_STD_ACTION

CWAN_RP-4-LCLOG_TOOLONG

4-Warning

Message too long from slot [dec]/[dec]: [dec] bytes

The WAN module passed down a logger message that is too long for\n\ the RP to handle.

-

LOG_STD_ACTION

CWAN_RP-3-LCLOG_BADSEV

3-Error

Invalid message severity from slot [dec]/[dec]: [dec]

The WAN module passed down a logger message with an invalid\n\ severity level that the RP could not handle.

-

LOG_STD_ACTION

CWAN_RP-3-SLOTCACHE_SYNTAX

3-Error

Error [chars]!

The RP failed to parse the slot configuration string.

-

LOG_STD_ACTION

CWAN_RP-7-SLOTCACHE_CARDTYPE

7-Debug

parsed slot [dec] fci_type [dec]

Information parsed from the slot configuration string by the RP.

-

LOG_STD_NO_ACTION

CWAN_RP-7-SLOTCACHE_PATYPE

7-Debug

Bay [chars] has type [dec] ports[hec]

Information parsed from the slot configuration string by the RP.

-

LOG_STD_NO_ACTION

CWAN_RP-3-CHANGE_POSEIDON_NEGOTIATION

3-Error

Unable to change negotiation. Failed to send message to\n\ slot [dec] port [dec]!

MSFC2 failed to send message to change negotiation to\n\ OSM-4GE-WAN-GBIC

-

LOG_STD_ACTION

CWAN_RP-3-OIRTWICE

3-Error

Slot [dec] OIR insertion/removal not paired up: [chars]

An internal OIR-related error occured for the specified WAN\n\ module.

cwtlc

LOG_STD_ACTION

CWAN_RP-3-IFCONFIG_ERR

3-Error

Interface config failed on port [dec]/[dec] cmd [dec] retval [dec]

A configuration command sent from the system to a linecard failed

osm-ct3

LOG_STD_ACTION

CWAN_RP-4-SEMAHOG

4-Warning

Process [dec] [chars] hogging [chars]! calling proc [dec] [chars]

-

-

-

CWAN_RP-4-IPCFAILED

4-Warning

IPC failed to send RPC message to WAN module

The RP failed to send an RPC message via IPC to a WAN module.

cwan

LOG_STD_NO_ACTION

CWAN_RP-3-PROCMSG

3-Error

Process msg send failed for process[dec]

Process message send failed.

cwan

LOG_STD_ACTION

CWAN_RP-3-MODULE_TYPE

3-Error

cannot find FCI for module type [dec] in slot [dec]

An internal software error occurred while the system was detecting the module type for the module in the specified slot. The operation of the module will be affected.

osm-basecard

LOG_STD_ACTION

CWAN_RP-4-MODULE_CONFIG_MISSING

4-Warning

configuration not available/not matching in startup-config for slot [dec]

Some information regarding the configuration of the module in the specified slot is missing. Any configuration in the startup-config for the interfaces will not be applied. If the module in the specified slot is a FlexWAN the missing configuration information is details of the Port Adapters in the FlexWAN module. This information is missing from the <CmdBold>SLOTCACHE<NoCmdBold> ROMMON variable.

osm-basecard

-

CWAN_RP-4-LL_UNKNOWN

4-Warning

Unknown linecard message: type [dec] [chars]

Mismatch version between RP and LC or internal message format mismatch

cwan

LOG_STD_NO_ACTION

CWAN_RP-3-GBIC_INSERTED

3-Error

GBIC media type [dec] inserted in [chars]

A GBIC was inserted in the interface.

cwan

LOG_STD_NO_ACTION

CWAN_RP-3-GBIC_REMOVED

3-Error

GBIC removed from [chars]

The GBIC was removed from the interface.

cwan

LOG_STD_NO_ACTION

CWAN_RP-1-TOO_MANY_VRF

1-Alert

Slot [dec] can not support all the VRFs configured!

A non-Enhanced OSM card has been inserted into a router with more than 511 IP VRFs already configured. This router cannot support more than 511 IP VRFs if there is at least one non-Enhanced OSM in the system.

cwan

"Replace the inserted non-Enhanced OSM with " "an Enhanced OSM or decrease the number of " "IP VRFs to 511 or fewer."

CWAN_HA-3-CCB_INIT_ERROR

3-Error

Failed to initialize CCB list for slot [dec].

The High Availability component for WAN modules failed to properly initialize state information for the specified slot.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-CCB_PLAYBACK_ERROR

4-Warning

CCB playback failed for slot [dec].

The High Availability component for WAN modules failed to synchronize some new state information for the specified slot.

c7600-ha

"Reload the standby supervisor module to force a fresh bulk " "synchronization. If this error recurs " LOG_STD_ACTION

CWAN_HA-4-CCB_RECORD_ERROR

4-Warning

CCB record failed for slot [dec].

The High Availability component for WAN modules failed to record some new state information for the specified slot.

c7600-ha

LOG_STD_ACTION

CWAN_HA-3-IFCFG_INIT_ERROR

3-Error

Failed to initialize Interface Configuration list for slot [dec]/[dec].

The High Availability component for WAN modules failed to properly initialize state information for the specified slot.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-IFCFG_PLAYBACK_ERROR

4-Warning

Interface Configuration command [dec] playback failed for slot [dec]/[dec].

The High Availability component for WAN modules failed to synchronize some new state information for the specified slot.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-IFCFG_RECORD_ERROR

4-Warning

Interface Configuration command [dec] record failed for slot [dec]/[dec].

The High Availability component for WAN modules failed to record some new state information for the specified slot.

c7600-ha

LOG_STD_ACTION

CWAN_HA-3-IFCFG_NO_UNIQUE_KEY

3-Error

No unique-key generator registered for interface configuration command [dec].

The High Availability component for WAN modules is unable to properly synchronize state information for the current configuration.

c7600-ha

LOG_STD_ACTION

CWAN_HA-3-IFCFG_CMD_NOT_UNIQUE

3-Error

More than one command registered for unique-key generator for interface configuration command [dec].

The High Availability component for WAN modules is unable to properly synchronize state information for the current configuration due to a conflict in command identifiers.

c7600-ha

LOG_STD_ACTION

CWAN_RP-4-IFCFG_CMD_TIMEOUT

4-Warning

Interface configuration command 0x[hec] to slot [dec]/[dec] timed out

The RP sent an configuration command to the slot specified in the error message and received no confirmation for the command.

c7600-ha

LOG_STD_ACTION

CWAN_RP-3-IFCFG_CMD_NOT_OWNER

3-Error

Process '[chars]' waiting for interface configuration command 0x[hec] to

A process on the RP sent an configuration command to the slot specified in the error message and a different process waited for the result. This could cause incorrect line card configuration states.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-IFCFG_DFLT_LIST_ERROR

4-Warning

For Interface Configuration command [dec] default retval list search resulted 0x[hec] for slot [dec]/[dec]

The High Availability component for WAN modules failed to synchronize some new state information for the specified slot.

c7600-ha

show platform redundancy \ if-config default-retvals

CWAN_HA-4-SRPSYNC

4-Warning

Slot [dec]: [chars]\n

An error occured while syncing SRP states from active RP to standby RP.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-NOSRPBULKSYNC

4-Warning

Failed to [chars] SRP bulk data slot=[dec] intf=[dec] type=[dec] ret code [dec]\n

Some SRP-related state information failed to sync correctly from the active RP to the standby RP during the HA bulk-synchronization phase.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-NOSRPSYNC

4-Warning

Failed to sync SRP packet slot=[dec]intf=[dec] to standby

Some SRP-related state information failed to sync correctly from the active RP to the standby RP when the configuration changed.

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-LTLSYNCFAIL

4-Warning

Failed to sync LTL data during [chars] for [chars] [dec]: slot=[dec]slotunit=[dec] if_num=[dec] to standby vlan=[dec]hash=[dec]ltl=[dec]\n

Some LTL data did not sync correctly from active to standby RP\n

c7600-ha

LOG_STD_ACTION

CWAN_HA-4-IFEVENT_INCRSYNCFAIL

4-Warning

[chars] for ifevent: [dec] with error: [dec]

Failed CWAN if-event incremental sync.

c7600-ha

LOG_STD_NO_ACTION

CWAN_HA-4-IFEVENT_BULKSYNCFAIL

4-Warning

[chars] ifevent: [dec] error: [dec]

Failed CWAN if-event bulk sync.

c7600-ha

LOG_STD_NO_ACTION

CWAN_HA-4-IFEVENT_UNEXPECTED_BULKTYPE

4-Warning

Unexpected value for bulk sync type [dec] received.

Received a unexpected type in bulk sync message.

c7600-ha

LOG_STD_NO_ACTION

CWAN_RP-6-UPGRADE_COMPLETE

6-Information

Slot [dec]: ROMMON upgrade complete. Reset the card for the changes to take effect.

The ROMMON upgrade has completed successfully. The card must be reloaded for the changes to take effect

-

LOG_STD_NO_ACTION

CWAN_RP-3-UPGRADE_ERROR

3-Error

Slot [dec]: The ROMMON upgrade failed to complete.

An error occurred during the upgrade process.

vpn-sm

"If the module reloads successfully please check " "the file and try again otherwise please contact " "your Cisco technical support representative."

CWAN_RP-6-AUX_FILE

6-Information

Slot [dec]: Found VPN-SM Firmware in File: \[chars]\

The file specified in the message was found and will be loaded by the VPN Services Module instead of the bundled image.

-

LOG_STD_NO_ACTION

CWAN_RP-6-ADF_FILE

6-Information

Slot [dec]: Using VPN-SM Upgrade File: \[chars]\

Booting specified upgrade image for VPN Services Module.

-

LOG_STD_NO_ACTION

CWAN_RP-6-OVERRIDE

6-Information

Slot [dec]: ...Overriding Intrinsic VPN-SM Firmware.

Specified image will be used instead of bundled image.

-

LOG_STD_NO_ACTION

CWAN_RP-1-OVERRIDE_MAC_INVALID

1-Alert

[chars] has invalid override-mac-address.

The user has issued an override-mac-address that does not match the mac address of the MSFC. This can occur if the config has been moved to new hardware or the mac-address command has been used on another interface. while the system automatically corrects this the config needs to be adjusted.

cwan

"Modify the override-mac-address command in the config."

CWAN_RP-3-WAN_BRIDGING_CFG_EXCD

3-Error

The number of VPLS/EoMPLS/Bridging/QinQ VCs exceeded the maximum[dec]

Review the configuration guidelines for the features that are being configured and reduce the number of VPLS EoMPLS Bridging to the number that is supported by the platform.

osm-bridge

-

CWAN_RP-6-OUT_OF_RESOURCE

6-Information

[chars] configuration has exceeded available internal resources.

The resources required for configuration are no longer available. They may have been acquired by another application.

osm-mpb

"If the requested resources have not been allocated " "to another application call your technical support representative " "for further assistance."

CWAN_RP-4-EMPTY_CWANBAYS

4-Warning

FLEXWAN in slot [dec] is empty. Please remove the Flexwan or insert it with atleast one PA

The FLEXWAN in the specified slot does not contain any Port Adapters.

-

"The FLEXWAN should be removed as this is an unsupported configuration"

CWAN_RP-6-LC_RESET

6-Information

The RP is reloaded resetting slot [dec] is necessary. Please ignore errors if any till the linecard comes up.

If the system is running Catalyst operating system software on the supervisor engine and Cisco IOS software on the MSFC the WAN line cards that power up before the RP powers up will be reset automatically.

cwpa

LOG_STD_NO_ACTION

CWAN_RP-3-FAILED_CONFIG

3-Error

Failed to send line card config message [chars] for slot [dec] port [dec]

The RP could not send the specified configuration message to the line card

osm-gigwan

LOG_STD_ACTION

CWAN_RP-4-INVALID_UNIT

4-Warning

Invalid 7600 Unit: [[dec]/[dec]].

The specified 7600 slot/cpu beyonds the Chassis's limit.

c7600-ha

"Power cycle the redundant supervisor"

CWAN_RP-4-INCR_CFG_SYNC_FAIL

4-Warning

7600 incremental running-config sync for [[dec]/[dec]] failed - [chars][dec]

The specified 7600 incremental running-config sync failed

c7600-ha

"Power cycle the redundant supervisor"

CWAN_RP-4-CONFIG_MISMATCH

4-Warning

\n\nIrreconcilable Configuration difference between Active & Standby Supervisors due to OIR/Config Event for [dec]/[dec] -> Reloading Standby Supervisor to synchronize the configuration.\n\n

Unexpected configuration difference between Supervisors.

c7600-ha

"None. This is expected behavior."

CWAN_CONTAINER_ACCESS-5-CWAN_VRF_MISMATCH

5-Notice

VRF of [chars] access does not match with [chars]

VRF of access interface does not match with that of associated container interface. Either container interface is deleted or VRF of container interface is changed

c7600-bb

LOG_STD_NO_ACTION

CWAN_CONTAINER_ACCESS-5-CWAN_NO_CONTAINER

5-Notice

Associated container interface does not exist for [chars]

The container interface no longer exists for access interface.

c7600-bb

LOG_STD_NO_ACTION

CWAN_RP-6-NOPWRISSU

6-Information

Spa inserted in [chars] powered down because ISSU is in progress

The Spa insertion detected during ISSU upgrade process. It will be acted upon completion of the ISSU process.

-

LOG_STD_NO_ACTION

CWAN_RP-3-CWAN_IFCOM_RMI

3-Error

Cwan ifcom RMI failure - [chars][dec]

The CWAN IFCOM RMI Registration.

c7600-env

LOG_STD_NO_ACTION

CWAN_RP-6-COREDUMP_ENABLED

6-Information

No heartbeat or keepalive resets will occur for slot [dec] since coredump has been enabled

The module in the slot has crashed and is configured to generate a coredump file. The module will not be reset due to heartbeat and keepalive failures to ensure the coredump file generation is not prematurely terminated.

c7600-env

LOG_STD_NO_ACTION

CWAN_RP-6-SESS_LIMITS_CHASSIS

6-Information

Exceeded max number of sessions supported. \nSupported limit 32000/chassis

Total number of subscriber sessions on this chassis exceeded the allowed limits. The supported limit is 32000 sessions per chassis

c7600-bb

"Avoid bringing up more number of sessions " "than the supported limit"

CWAN_RP-6-SESS_LIMITS_SIP400

6-Information

Exceeded max number of sessions supported on SIP400 LC in slot [dec]. \nSupported limit 8000/SIP400

Total number of subscriber sessions on SIP400 line card exceeded the allowed limits. The supported limits is 8000 sessions per SIP400

c7600-bb

"Avoid bringing up more number of sessions " "than the supported limit"

CWAN_RP-6-SESS_LIMITS_ES_PLUS

6-Information

Exceeded max number of sessions supported on ES+ LC in slot [dec]. \nSupported limit 16000/ES+

Total number of subscriber sessions on ES+ line card exceeded the allowed limits. The supported limit is 16000 sessions per ES+

c7600-bb

"Avoid bringing up more number of sessions " "than the supported limit"

CWAN_RP-6-SESS_LIMITS_PORT_GROUP

6-Information

Exceeded max number of sessions supported on port-group Gig[dec]/[dec] to Gig[dec]/[dec].\nSupported limit 4000/port-group on ES+ LC

Total number of subscriber sessions on a single port-group in ES+ exceeded the allowed limits. The supported limit is 4000 sessions per port-group

c7600-bb

"Rearrange the subscribers on ES+ in such a way " "maximum number of sessions supported in a port-group is 4000."

CWAN_RP-6-SESS_LIMITS_TEN_GIG_PORT

6-Information

Exceeded max number of sessions supported on port Te[dec]/[dec]. \nSupported limit 8000/port on a Ten Gig port on ES+ LC.

Total number of subscriber sessions on a single Ten Gig port in ES+ exceeded the allowed limits. The supported limit is 8000 sessions per Ten Gig port.

c7600-bb

"Rearrange the subscribers on ES+ in such a way that " "maximum number of sessions per Ten Gig port is 8000"

CWAN_RP-6-PLAT_AVL_DEL_FAILED

6-Information

Platform AVL delete failed for PPPoE session due to wrong slot id [dec]

Deletion of session related information from the AVL tree failed because the slot number used to index it is wrong

c7600-bb

LOG_STD_NO_ACTION

CWAN_T3E3-3-IFCONFIG_ERR

3-Error

Interface config error on T3 port [dec]/[dec] cmd [dec] retval [dec]

A configuration command sent from the system to a linecard failed

osm-t3e3

LOG_STD_ACTION

CWAN_CHOC_DSX-3-UNKNOWN_CTRLR

3-Error

Slot [dec] - Unknown linecard type [dec]

This hardware can't be recognized by this version of software.

osm-ct3

"Check software version. Make sure the software supports the hardware."

CWAN_CHOC_DSX-3-T3CFG_ERROR

3-Error

T3 [dec]/[dec] config command error cmd [dec] arg [dec] retval [dec]

A command sent from the system to a linecard failed

osm-ct3

LOG_STD_ACTION

CWAN_CHOC_DSX-3-T1CFG_ERROR

3-Error

T1 [dec]/[dec]/[dec] config command error cmd [dec] arg [dec] retval [dec]

A command sent from the system to a linecard failed

osm-ct3

LOG_STD_ACTION

CWAN_CHOC_DSX-3-VCCFG_ERROR

3-Error

VC [dec]/[dec]:[dec] config command error cmd [dec] arg [dec] retval [dec]

A command sent from the system to a linecard failed

osm-ct3 for CT3 osm-choc-ds0 for CHOC-12

LOG_STD_ACTION

CWAN_CHOC_DSX-3-NULLDS3MIBTABLE

3-Error

Null DS3 MIB table snmp_if_index [dec]

System cannot find the DS3 MIB table pointer

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-3-SEND_DRIVER_READY

3-Error

send driver ready msg failed for [dec]

IPC message failure

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Inform the network operator that subrate configuration changed by\n\ remote end"

CWAN_CHOC_DSX-3-ENQUEUE_FAIL

3-Error

[chars]

cmd enqueue failure

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-5-UNKNOWN_EVENT

5-Notice

[chars]

Unexpected event received by the process

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

process creation failed for handling cmd

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-3-PROCESS_ERROR

3-Error

process error - [chars]

process encountered fatal error

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-3-INVALID_SUBR_HWIDB

3-Error

Invalid Subrate hwidb on T3 [dec]/[dec]

invalid subrate hwidb

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-3-VC_CONFIG_ERR

3-Error

[chars] T1 [dec] channel group [dec] of T3 [dec]/[dec] unsuccessful error code [dec]

channel configuration error

osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DSX-3-NODESTROYSUBBLOCK

3-Error

The [chars] subblock named [chars] was not removed

A software error has occured this message is displayed when\n\ IDB subblocks cannot be removed.

osm-ct3 for CT3 osm-t3e3 for T3/E3 \n\ osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_ACTION

CWAN_CHOC-4-ALLOCFAIL

4-Warning

Interface [dec]/[dec] allocation failed: [chars]

required resources unavailable.

osm-choc-ds3

"Either upgrade system memory or reconfigure memory usage."

CWAN_CHOC-4-UNSUP

4-Warning

Slot [dec]: Unknown [chars] [dec]

This value is not recognized by this version of software.

osm-choc-ds3

"Check linecard version. Normally this is harmless but worth contacting\n\ cisco technical support representative."

CWAN_CHOC-4-IFCONFIG

4-Warning

[chars] config error [dec] lc delay:[dec] ms: [chars]

RP received configuration error from linecard.

osm-choc-ds3

"Reconfigure or shut/no shut the error channel."

CWAN_CHOC-4-PROV_FAIL

4-Warning

Interface [chars] provisioning ch[dec] failed: [chars]

provisioning conflict or resource shortage

osm-choc-ds3

"workaround: under 'controller sonet' do 'no channelized' followed\n\ by 'channelized' twice. If problem persists do a\n\ 'show controller sonet <slot>/<port>' and\n\ 'show controller {pos/serial} <slot>/<port>:<chan>' then contact\n\ cisco technical support representative."

CWAN_CHOC-4-UNPROV_FAIL

4-Warning

Interface [chars] unprovisioning failed: [chars]

Linecard failed to response unprovisioning command.

osm-choc-ds3

LOG_STD_ACTION

CWAN_CHOC-4-CORRUPT

4-Warning

[chars] information seems to be corrupted bad value =[dec]

wrong parameters detected internally

osm-choc-ds3

"This is only a debug warning message. The unexpected value is\n\ discarded."

CWAN_CHOC-4-LCLOCK_FAIL

4-Warning

Interface [chars] failed to acquire semaphore for LC access: [chars]

Other process locked the semaphore for too long.

osm-choc-ds3

LOG_STD_ACTION

CWAN_CHOC-4-LCCFG_MISMATCH

4-Warning

LC needs reboot due to config mismatch on [chars] rc=[dec]

RP detects LC's channel provisioning mismatching start-config

osm-choc-ds3

"reset linecard: hw-module module <slot> reset"

CWAN_CHOC-4-WRONG_LL

4-Warning

%.16s received wrong loveletter : type=[dec] length=[dec]

wrong parameters detected internally

osm-choc-ds3

"This is only a debug warning message. The unexpected messages from\n\ linecard is harmlessly discarded."

CWAN_CHOC-6-WRONG_GULF

6-Information

[chars] hardware version gulf v[dec] does not support OC-12 or OC-48

Early version of hw asic GULF2.0 and below has bugs in\n\ rx fifo depth which can not handle oc-12 or oc-48 rate.\n\ Either limiting channel provisioning or upgrading hw

osm-choc-ds3

"Limit channel provisioning to DS3 and/or OC3"

CWAN_CHOC-6-LCDRIVER

6-Information

OIR failed: slot [dec] linecard not responding to initial query

OIR insertion aborted due to failing to contact lc

osm-choc-ds3

LOG_STD_ACTION

CWRPSPA-3-NO_HOST_INFO

3-Error

slot [dec] subSlot [dec] spaType 0x[hec]

Failed to get information about the host linecard.

cwan

LOG_STD_SH_TECH_ACTION

CWRPSPA-3-MAX_SPA

3-Error

Power to IPSEC-SPA-2G in [chars] is denied because it has exceeded the number allowed[dec]

The number of IPSEC-SPA-2G in a chassis is limited. This message is displayed when the number of IPSEC-SPA-2G in the chassis has exceeded this limit.

cwan

"Use only the number of supported IPSEC-SPA-2G"

CWRPSPA-3-SPA_NO_HOST_INFO

3-Error

slot [dec] subSlot [dec] PID [chars]

Failed to get information about the host linecard.

cwan

LOG_STD_SH_TECH_ACTION

CWRPSPA-3-HWIDB_FAILURE

3-Error

Creation: slot [dec] subSlot [dec] port [dec] vc [dec]

Failed to create an interface hwidb.

cwan

LOG_STD_SH_TECH_ACTION

CWRPSPA-3-INVALID_PORT_NUM

3-Error

slot=[dec] port=[dec] hwidbType=0x[hec] max_port_num=[dec] LCtype=0x[hec]

The port number is out of range.

cwan

LOG_STD_SH_TECH_ACTION

CWRPSPA-4-SPA_RESP_CMD_MISMATCH

4-Warning

[chars]: Expecting response to interface configuration command \[chars]\ but received response to command \[chars]\.

An internal synchronization error occurred while configuring the interface. The configuration may not have succeeded.

cwan

"Check that the running configuration for the " "interface is correct. If this message occurred on the standby try " "reloading the standby to ensure that its configuration is in sync. " "If this message is repeatable please " LOG_STD_SH_TECH_ACTION

CWRPSPA-6-CARDRELOAD

6-Information

Module [dec] reload due to SPA insert in [dec]/[dec].

When inserting a SPA on this carrier card the card is reset.

-

LOG_STD_NO_ACTION

CWRPSPA-4-SPA_CMD_NO_RESP

4-Warning

[chars]: No response for interface configuration command \[chars]\

A timeout occurred while RP was waiting for a response from line card. This may happen due to line card CPU being too busy to respond to the command.

cwan

LOG_STD_NO_ACTION

CWRPSPA-5-OUT_OF_RESOURCES

5-Notice

[chars]: Unable to create [chars] due to SPA resource limitations.

The SPA was unable to create the requested resource due to limited hardware or software resources

-

LOG_STD_NO_ACTION

CWANLC_ATM-4-UNSUP

4-Warning

[chars]: unsupported feature: [chars]

This feature is not supported by Draco ATM RP.

cwtlc

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWANLC_ATM-3-CMDERR

3-Error

[chars]: [chars] IPC command fails cause: 0x%04x

The ATM RP driver experienced IPC command error.

cwtlc

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWANLC_ATM-3-IPC_ERROR

3-Error

[chars]: IPC command \[chars]\ failure due to \[chars]\

The SPA ATM RP driver experienced IPC command error.

spa-atm-all

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWANLC_ATM-4-MISMATCH_VCENCAP

4-Warning

[chars]: Cannot mix VC encapsulation types in multipoint interfaces

This ATM card only allows VC encapsulations of the same type on the main interface or multipoint subinterfaces

-

"Reconfigure the ATM interface with matching VC encapsulations"

CWANLC_ATM-3-VCCLOSEFAIL

3-Error

[chars]: Failed to remove VC [dec]/[dec] cause [dec]

Attempt to remove VC on the linecard failed.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWANLC_ATM-3-VPCLOSEFAIL

3-Error

[chars]: Failed to remove VP [dec] cause [dec]

Attempt to remove VP on the linecard failed.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWANLC_ATM-3-NOVPSPACE

3-Error

[chars]: out of VP space for VPI [dec]

Out of VPs on the SAR.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWANLC_ATM-4-SEMHOG

4-Warning

[chars]: Process [dec] [chars] hogging semaphore -- called by process [dec] [chars]

The named process has held the resource semaphore longer than\n\ expected.

-

LOG_STD_NO_ACTION

CWANLC_ATM-4-CLOSEPEND

4-Warning

[chars]: The TX SAR is currently freeing internal buffers previously allocated for the identical channel id. The execution of the current command is delayed.

The TX SAR has taken longer than expected to free its internal buffers.

-

LOG_STD_NO_ACTION

CWAN_CHOC_DS0-3-UNKNOWNCTRLR

3-Error

Slot [dec] - Unknown linecard type [dec]

This hardware can't be recognized by this version of software.

osm-choc-ds0

"Check software version. Make sure the software supports the hardware."

CWAN_CHOC_DS0-3-RMCTRLR_UNKNOWN

3-Error

Slot [dec] - Unknown linecard type [dec] removed

This hardware can't be recognized by this version of software.

osm-choc-ds0

"Check software version. Make sure the software supports the hardware."

CWAN_CHOC_DS0-3-CDBFAIL

3-Error

Port [dec]/[dec] - fail to create a SONET controller data structure

The software resource can't be allocated for this hardware

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-3-PORTFAIL

3-Error

Port [dec]/[dec] - fail to create a port instance data structure

The software resource can't be allocated for this hardware

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-3-T1CFG_CCBERROR

3-Error

CCB command error cmd [dec] arg [dec] on T1 [dec]/[dec]/[dec]

A command sent from the system to a linecard failed

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-3-VCCFG_CCBERROR

3-Error

CCB command error cmd [dec] arg [dec] on port [dec]/[dec] channel [dec]

A command sent from the system to a linecard failed

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-3-IFCONFIG_ERR

3-Error

config error on port [dec]/[dec][chars] cmd [dec] [chars]

A configuration command sent from the system to a linecard failed

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-4-UNSUP

4-Warning

Slot [dec]: Unknown [chars] [dec]

This value is not recognized by this version of software.

osm-choc-ds0

"Check linecard version. Normally this is harmless but worth contacting\n\ cisco technical support representative."

CWAN_CHOC_DS0-3-CFG_BAD_PARA

3-Error

[chars]: invalid config parameter [chars]

Configuration parameter is invalid

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-4-IFCONFIG

4-Warning

[chars] config error [dec] lc delay:[dec] ms: [chars]

RP received configuration error from linecard.

osm-choc-ds0

"Reconfigure or shut/no shut the error channel."

CWAN_CHOC_DS0-4-ALLOCFAIL

4-Warning

Interface [dec]/[dec] allocation failed: [chars]

required resources unavailable.

osm-choc-ds0

"Either upgrade system memory or reconfigure memory usage."

CWAN_CHOC_DS0-4-PROV_FAIL

4-Warning

Interface [chars] provisioning ch[dec] failed: [chars]

provisioning conflict or resource shortage

osm-choc-ds0

"workaround: under 'controller sonet' do 'no channelized' followed\n\ by 'channelized' twice. If problem persists do a\n\ 'show controller sonet <slot>/<port>' and\n\ 'show controller {pos/serial} <slot>/<port>:<chan>' then contact\n\ cisco technical support representative."

CWAN_CHOC_DS0-4-UNPROV_FAIL

4-Warning

Interface [chars] unprovisioning failed: [chars]

Linecard failed to response unprovisioning command.

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-4-WRONG_LL

4-Warning

%.16s received wrong loveletter : type=[dec] length=[dec]

wrong parameters detected internally

osm-choc-ds0

"This is only a debug warning message. The unexpected messages from\n\ linecard is harmlessly discarded."

CWAN_CHOC_DS0-4-CORRUPT

4-Warning

[chars] information seems to be corrupted bad value =[dec]

wrong parameters detected internally

osm-choc-ds0

"This is only a debug warning message. The unexpected value is\n\ discarded."

CWAN_CHOC_DS0-4-LCLOCK_FAIL

4-Warning

Interface [chars] failed to acquire semaphore for LC access: [chars]

Other process locked the semaphore for too long.

osm-choc-ds0

LOG_STD_ACTION

CWAN_CHOC_DS0-3-UNKNOWN_MIB_TYPE

3-Error

Unknown MIB type [dec] from slot [dec]

Draco received unknown communication message from linecard

osm-choc-ds0

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWAN_CHOC_DS0-5-LOOPSTATUS

5-Notice

[chars] [chars]

A configurable loopback status.

-

LOG_STD_NO_ACTION

CWANLC-6-BUSSTALL

6-Information

Constellation BUS Stall detected

This message indicates that a stall was detected on the Constellation Bus probably due to some OIR activity on the Bus.

-

"No action needed Informational."

CWANLC-6-LONGSTALL

6-Information

Long bus stall [dec] ms check for improperly seated cards

This message indicates that a stall was detected but the backplane stall was longer than expected.

-

"Make sure all cards are firmly seated. If the " "problem reoccurs it may indicate a hardware failure."

CWANLC-6-BUSSTALLCLEAR

6-Information

Constellation BUS Stall cleared

This message indicates that a stall was cleared on the Constellation Bus.

-

"No action needed Informational."

CWANLC-5-NOSCPPING

5-Notice

Linecard has not sent SCP PING responses for too long

SCP ping mechanism is used by RP/SP processors to monitor if the linecard executing IOS is in a healthy state. This SCP ping response has not been sent by the line card for long time now - the line card has exported its context information to the RP and may be powercycled. The exported context is available in the output of 'show diag'

cwpa

"Save the 'show diag' output generated and contact your " "technical support representative if the line card is reset"

CWANLC-2-PCIERROR

2-Critical

Fatal PCI Error [chars] seen on PCI Bus [dec]

A Fatal PCI Error was detected on the PCI bus. Most likely it is a hardware problem.

-

"Call your technical support representative for " "assistance if this message persists."

CWANLC-4-LOGMSGTOOBIG

4-Warning

Logger message length exceeds max [dec] bytes

The Linecard attempted to send a large message to the Route Processor Draco.

-

LOG_STD_ACTION

CWANLC-3-IPCPORT

3-Error

Failed to [chars] IPC port '[chars]' error [chars]

The Linecard failed to create a port for communication with the Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CWANLC-3-IPCPORTFAIL

3-Error

Failed to open IPC port '[chars]' [chars]

The Linecard failed to open a port for communication with the Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CWANLC-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The Linecard failed to allocate a buffer for communication with the Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CWANLC-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The Linecard failed to send a message to the Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CWANLC-3-HWREVREADFAIL

3-Error

Failed to retrieve h/w version from EEPROM

The Linecard failed to read the hardware version from the CPU eeprom.

-

LOG_STD_ACTION

CWANLC-5-IPCPENDING

5-Notice

Too many messages [dec] in IPC pending queue

The IPC pending queue is growing. Will soon deplete the IPC header cache and the IO buffers

-

LOG_STD_ACTION

CWANLC-3-FATAL

3-Error

[chars]

The Optical Services Module line card has encountered a fatal error.

-

LOG_STD_ACTION

CWANLC-3-CWANLC_EARL_VERSION_NOTICE

3-Error

CWAN receives mismatch Earl version notification. New Earl[dec] vs Earl[dec]

The RP has determined via an SCP find operation that the version of the EARL switching engine on the line card has changed. This message occurs during switchover operation. The version of the EARL switching engine is specified in the message text.

-

LOG_STD_ACTION

CWANLC-3-TVPN_NOMEM

3-Error

Failed to start vpn not enough memory

The OSM card could not start VPN due to a memory exhaustion

-

"Reduce other system activity to ease memory demands. " "If conditions warrant upgrade to a larger memory " "configuration. If this message recurs "LOG_STD_ACTION

CWANLC-3-LTL_NOPPEPORTMAP

3-Error

Failed to retrieve default port mapping for packet processor [dec]

The linecard software initialization was not completed correctly

-

LOG_STD_ACTION

ENVM-3-NOFORK

3-Error

Could not create environmental polling process

-

-

""

ENVM-4-READERROR

4-Warning

Error reading temperature sensor [dec]

-

-

""

ENVM-4-LONGBUSYREAD

4-Warning

C2W Interface busy for long time reading temperature sensor [dec]

-

-

""

ENVM-4-WRITEERROR

4-Warning

Error writing temperature sensor [dec]

-

-

""

ENVM-4-LONGBUSYWRITE

4-Warning

C2W Interface busy for long time writing temperature sensor [dec]

-

-

""

CWANLC-3-FPD_INCOMPATIBLE

3-Error

FPD ID=[dec] image in this FPD package is for revision [dec].x boards. It is incompatible with current board revision of [dec].[dec]

This FPD package does not contain images that are compatible with the current board revision.

c7600-sip-common

"Perform the FPD upgrade operation with a newer version of FPD " "image package that is compatible with the running Cisco IOS " "software. Consult with the FPD image package section of the " "Cisco IOS software release note to confirm if your board " "revision is supported for a particular release."

CWAN_SPA-3-CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

Failed to create a SPA object.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-SPA_CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec].

Failed to create a SPA object.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-FAILURE

3-Error

[chars]: SPA failure - cause: [chars] [hex] recovery action: [chars] [dec]

The SPA failed for the specified reason

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-NULL_VFT

3-Error

[chars] virtual function table is not initialized. spaType=0x[hec]

A required function table is not initialized

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-NULL_VFUNC

3-Error

[chars] vector is not initialized. spaType=0x[hec]

A required function vector is not initialized

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-MEM_ALLOC_ERROR

3-Error

[chars]

Memory allocation error.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-INVALID_INDX_RANGE

3-Error

index1= [dec] index2= [dec] maxIndex= [dec]

Invalid index range.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-INVALID_IF_INDEX

3-Error

index= [dec] cardType=0x[hec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec]

Index for the interface is not valid.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-INVALID_DATA_INSTANCE

3-Error

interface type [chars] slot [dec] port [dec] vc [dec] : [chars]

Data required to support the interface is not available.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-NULL_ATM_DB

3-Error

Unable to create ATM DB for [chars]

Data required to support the interface is not available.

FIX-ME

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-POWER_CYCLE

3-Error

[chars] occurred on Shared Port Adapter [dec]/[dec]

An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled

msc-200-ha

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-DIAG_CONFIG

3-Error

[chars] did not complete [dec]/[dec]

An error has occured during diagnostic test.

c7600-field-diag

LOG_STD_SH_TECH_ACTION

CWAN_SPA-3-INTR_THROTTLE

3-Error

Interface [chars] MAC interrupt was throttled.\n\ Reenabling MAC interrupts via one sec spa process

MAC interrupt burst has occurred on one of the interfaces on the link daughtercard. The error message indicates that a throttling mechanism has been applied to this port to avoid any operational damage that could be provoked by this event. The cause for this problem could be bad transceiver highly frenquent flapping optical signals or mismatched path signals e.g. receiving 10GBASE-W signal on 10GE LAN interface etc.

c7600-esm-20

"Check the interface configuration and received signal characteristics. " "Also verify the XFP transceiver and receive signal path to determine the " "If this message recurs " LOG_STD_ACTION

CWPA-3-NODISPATCH

3-Error

Dispatch vector Null cmd=[dec] dintf=[dec]

No command dispatch vector was found for the specified interface.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWPA-3-BADMALUCMD

3-Error

Unsupported MALU command [dec] arg=[hex] pascb=[hex]

-

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWPA-3-CMDNOPASCB

3-Error

PASCB Null for command [dec] arg=[hex]

-

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWPA-3-BAD_IFCOMTYPE

3-Error

Bad ifcom message type=[dec]

-

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWPA-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The FlexWAN line card failed to allocate a buffer for communication with the Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CWPA-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The FlexWAN line card failed to send a message to the\n\ Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWPA-3-DIAGFAIL

3-Error

Failed to handle diag [chars] [dec]

The FlexWAN line card failed to execute diag command. Further details are specified in the text that is displayed on the console or in the system log.

cwpa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CWPA-3-LVLTRTOOBIG

3-Error

Loveletter length exceeds max [dec] bytes

The FlexWAN line card attempted to send a large message to the\n\ Route Processor Draco.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CWPA-2-BAD_HWVERS

2-Critical

Unable to determine board hardware version

The line card software cannot read the line card hardware version. This condition indicates a hardware error.

cwpa

LOG_STD_ACTION

CWPA-2-PA_VOLFAIL

2-Critical

Port adapter [dec]V failed Reloading flexwan

The line card has encountered an error involving power delivery to the line card. Likely causes for this error are an environmental condition an overtemperature condition or inconsistent voltage to the line card.

cwpa

"Check the input voltage and temperature of the line card. " LOG_STD_RECUR_ACTION

CWPA-2-PAOIR

2-Critical

Port adapter OIR not supported reloading

An OIR operation occurred on the port adapters of the specified line card. OIR operations are not supported on the port adapter. This error has caused the line card to crash and reload.

cwpa

"Do not attempt an OIR operation on the port adapters of the specified " "line card."

CWPA-2-WHICH_INT

2-Critical

Unexpected [chars] interrupt INT status = 0x[hec]

The line card specified in the error message has encountered an unexpected interrupt.

cwpa

LOG_STD_ACTION

CWPA-4-HEADER_TOO_BIG

4-Warning

Needs [dec] bytes with only [dec] bytes available. Packet size [dec] received from [chars] buffer [hex] packet start [hex]:\n %-08x:%08x %08x %08x %08x %08x %08x %08x %08x\n %-08x:%08x %08x %08x %08x %08x %08x %08x %08x\n

A packet was sent from the PA to either the route processor or the line card. That packet did not have enough available space to append the header. A new particle has been linked to the packet to store the header.

-

LOG_STD_NO_ACTION

CWPA-3-PROCCREATEFAIL

3-Error

Failed to create [chars] process

The Linecard failed to create a process which\n\ which is necessary for proper functioning of the\n\ linecard.

cwpa

"Copy the error message as it appears and\n\ report it to your technical support \n\ representative. If it is the 'stats export\n\ process' then you might not see input/output\n\ rate and bytes getting incremented in 'show\n\ interface' output for flexwan/flexwan2 non-\n\ channelised interfaces. However you can get\n\ the stats from 'show interface acc' or 'show\n\ interface stats'."

CWPAATOM-3-BADLTL

3-Error

Bad LTL index 0x[hec] for vlan [dec] local_vc_label [dec]

Local Target Logic index value is invalid

7600-mpls

"If your EoMPLS traffic is fine then ignore this \n\ If not then contact your Cisco technical support representative."

CONST_ISSU-3-MSG_NOT_OK

3-Error

[chars][dec]: ISSU message type [dec] is not compatible

ISSU received a message not compatible with the running version.

CONST_ISSU_PLATFORM

"show message type <Client_ID>"

CONST_ISSU-3-MSG_MTU

3-Error

[chars][dec]: Client failed to get mtu for message [dec] [chars]

[chars][dec]: client cannot get the MTU for a message type

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-TRANSFORM_FAILED

3-Error

[chars][dec]: [chars] transformation failed [chars]

The transformation operation for the ISSU message has failed

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CF_SEND

3-Error

[chars][dec]: Client failed to send message [dec]

ISSU client cannot send a negotiation message to a peer

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-ICC_SEND

3-Error

[chars][dec]: Client failed to send message

ISSU client cannot send a negotiation message to a peer

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CLIENT_REG

3-Error

[chars][dec]: Client failed to register [chars]

The ISSU Client could not be registered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CLIENT_REG_FAILED

3-Error

[chars][dec]: Client is not

The ISSU Client is not yet initialized. The negotiation for this client is not yet done.

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-SESSION_REG

3-Error

[chars][dec]: session failed to register [chars]

The client's ISSU session could not be registered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-SESSION_UNREG

3-Error

[chars][dec]: session [dec]

The client's ISSU session could not be unregistered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-START_NEGO_FAILED

3-Error

[chars][dec]: failed to

The ISSU client cannot start its negotiation

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CAPTYPE_REG

3-Error

[chars][dec]: failed to

The ISSU client failed to register a capability type

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CAPENTRY_REG

3-Error

[chars][dec]: failed to register a capability entry [chars]

The ISSU client failed to register a capability entry

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CAPGROUP_REG

3-Error

[chars][dec]: failed to register a capability group [chars]

The ISSU client failed to register a capability group

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-MSGTYPE_REG

3-Error

[chars][dec]: failed to register a message type [chars]

The ISSU client failed to register a message type

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-MSGGROUP_REG

3-Error

[chars][dec]: failed to

The ISSU client failed to register a message group

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-ENTITY_REG

3-Error

[chars][dec]: failed to register

The ISSU entity could not be registered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-ENTITY_UNREG

3-Error

[chars][dec]: failed to unregister

The ISSU entity could not be unregistered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CAP_REG

3-Error

[chars][dec]: failed to register

The capabilities of the ISSU client could not be registered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-MSG_REG

3-Error

[chars][dec]: failed to register its messages [chars]

Messages for the ISSU client could not be registered

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CAP_EXCHANGE

3-Error

[chars][dec]: Capability exchange failed with error [chars]

The capability exchange failed the ISSU client is unable to process the received capability

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-NEGO_PROCESS

3-Error

[chars][dec]: Cannot create process: [chars]

The process to negotiate the session for the specified ISSU client cannot be created.

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-3-CONST_MTU_NOT_ENOUGH

3-Error

[chars][dec]: Requested buffer size [dec] is greater than the max MTU size

Checkpoint buffer size requested is greater than the max MTU size checkpoint supports

cat6000-ha

LOG_STD_ACTION

CONST_ISSU-3-MSG_POLICY

3-Error

[chars][dec]: Client failed to negotiate version for message type [dec] error [chars]

ISSU client cannot negotiate message to a peer

CONST_ISSU_PLATFORM

LOG_STD_ACTION

CONST_ISSU-2-NEGO_NOT_DONE

2-Critical

[chars][dec]: ISSU Negotiation not complete

Unable to complete ISSU negotiation.

CONST_ISSU_PLATFORM

LOG_STD_ACTION

ICC-2-NOMEM

2-Critical

No memory available for [chars]

The ICC subsystem could not obtain the memory it needed.

icc

LOG_STD_SH_TECH_ACTION

ICC-4-CONSISTENCY

4-Warning

Internal consistency check: [chars]

An internal inconsistency was found in some ICC data structures.

icc

LOG_STD_SH_TECH_ACTION

ICC-4-COMM

4-Warning

Communication failure occurred while [chars]

-

-

-

ICC-4-BAD_ACCOUNTING

4-Warning

ICC received a bad class [dec]

A communication failure has occurred between this card and\n\ another card in the system.

icc

LOG_STD_SH_TECH_ACTION

ICC-4-HEARTBEAT

4-Warning

Card [dec] failed to respond to heartbeat

A communication failure has occurred between the primary and\n\ the specified line card.

icc

LOG_STD_SH_TECH_ACTION

ICC-5-WATERMARK

5-Notice

[dec] [chars] [chars] pkts for class [chars] are waiting to be processed

Processor got packets for the class and are waiting to be procssed

icc

LOG_STD_SH_TECH_ACTION

ICC-2-OPEN

2-Critical

ICC Create Session Failed for card <0x[hec]> Queue <[chars]>

ICC was not able to create a session for the destination seat

icc

"collect output from 'show oir debug swover_global_mask' from SP"

ICC-2-JOIN

2-Critical

ICC mcast joining failed member <0x[hec]> to group <0x[hec]> with ipc error <[chars]>

ICC was not able to join a member for the mcast group

c7600-system

"collect output 'show icc mcast status' from RP"

ICC-5-HUGE_BUFFER

5-Notice

Class [[chars]] with Request id [dec] requested a huge buffer of Size [dec].

Huge packet requests would deplete the memory at the linecards

-

"ICC client is trying to request huge packet buffer " "Please use the command Show icc internal to get " "get the traceback and file a DDTS against the component"

ICC-3-MAST_BAD_FREE

3-Error

ICC multicast memory already freed

One of the ICC multicast request's memory was found to be free when response arrived

icc

LOG_STD_SH_TECH_ACTION

PFINIT-2-NOMEM

2-Critical

No memory available for [chars]

The PF subsystem could not obtain the memory it needed.

cat6000-ha

LOG_STD_SH_TECH_ACTION

PFINIT-2-IPCREINIT

2-Critical

Unable to reinitialzie IPC

The PF subsystem could not reinitailize IPC.

cat6000-ha

LOG_STD_SH_TECH_ACTION

PFINIT-2-IPCSEAT

2-Critical

Unable to add/remove IPC seats for [chars]

The PF subsystem could not add/remove IPC seats.

cat6000-ha

LOG_STD_SH_TECH_ACTION

PFINIT-2-EOBC

2-Critical

[chars]

The PF subsystem could not send IPC bootstap messages to RP.

cat6000-ha

LOG_STD_SH_TECH_ACTION

PFINIT-5-CONFIG_SYNC

5-Notice

Sync'ing the [chars] configuration to the standby Router.

The configuration has been successfully synced to the standby Router

cat6000-ha

"This is an informational message. No action is required."

PFINIT-5-CONFIG_SYNC_NOT_SUPPORTED

5-Notice

Sync'ing the [chars] configuration to the standby Router is not supported.

CONFIG_SYNC_FAIL_EXPLANATION

cat6000-ha

CONFIG_SYNC_FAIL_ACTION

PFINIT-1-CONFIG_SYNC_FAIL_RETRY

1-Alert

Sync'ing the [chars] configuration to the standby Router FAILED the file may be already locked by a command like: show config. Will attempt to sync [dec] more time[chars]

CONFIG_SYNC_FAIL_EXPLANATION

cat6000-ha

CONFIG_SYNC_FAIL_ACTION

PFINIT-1-CONFIG_SYNC_FAIL

1-Alert

Sync'ing the [chars] configuration to the standby Router failed.

CONFIG_SYNC_FAIL_EXPLANATION

cat6000-ha

CONFIG_SYNC_FAIL_ACTION

PFINIT-6-PROC_MAX

6-Information

Process-max-value changed from [dec] to [dec] millisecs

Informational messages regarding change in Process-max-value

-

-

SIPSPA-3-HWIDB_FAILURE

3-Error

Creation: port [dec] vc [dec]

Failed to create a hwidb.

SIP_DDTS_COMP

LOG_STD_SH_TECH_ACTION

SIPSPA-3-DEVICE_ERROR

3-Error

subSlot [dec] spatype 0x[hec]. Device error: [chars]

An error related to a device on the SPA is detected.

SIP_DDTS_COMP

LOG_STD_SH_TECH_ACTION

SIPSPA-3-ISR_RC_ERROR

3-Error

ISR return code out of range. rc=[dec]

The ISR error return code is out of range.

SIP_DDTS_COMP

LOG_STD_SH_TECH_ACTION

SIPSPA-4-SPABUS

4-Warning

Bay [dec] [chars] failed. sz=[dec] rd_par=[dec] noresp=[dec] err_l=[dec] addr=0x[hec] data=0x[hec] parity=0x[hec] deadman=[dec]

SPABUS has reported an error.

SIP_DDTS_COMP

LOG_STD_ACTION

SIPSPA-4-SPABUS2

4-Warning

Bay [dec] [chars] failed. sz=[dec] rd_par=[dec] noresp=[dec] absent=[dec] err_l=[dec] addr=0x[hec] data=0x[hec] parity=0x[hec] deadman=[dec]

SPABUS has reported an error.

SIP_DDTS_COMP

LOG_STD_ACTION

SIPSPA-6-OIR

6-Information

Bay [dec] [chars] changed to [chars]

SPA OIR Sequence

SIP_DDTS_COMP

LOG_STD_NO_ACTION

SIPSPA-4-MAX_BANDWIDTH

4-Warning

Total SPA bandwidth exceeds line card capacity of %lu Mbps

The total bandwidth of SPAs exceeds the rated capacity of this line card.

SIP_DDTS_COMP

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

SIPSPA-4-MAX_BANDWIDTH_NS

4-Warning

Total SPA bandwidth exceeds line card capacity installed combination of SPA interfaces is not supported

The total bandwidth of SPAs exceeds the rated capacity of this line card.

SIP_DDTS_COMP

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

SIPSPA-4-SPI_PORT_LIMIT_EXCEEDED

4-Warning

SPI port limit exceeded [chars] in [chars] has been powered down.

The total number of SPI ports required exceeds the capacity of this line card.

SIP_DDTS_COMP

"Refer to the line card guidelines for SPA combinations supported" "by this line card"

SIPSPA-3-POWER

3-Error

Bay [dec] 12V power is [chars]

SPA 12V power fault indicator

SIP_DDTS_COMP

LOG_STD_ACTION

SIPSPA-3-SPI4_INIT_FAILURE

3-Error

Bay [dec] initialization failure

Failed to create SPI4 subblock

SIP_DDTS_COMP

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

SIPSPA-3-MESSAGE_ERROR

3-Error

Bay [dec]: [chars]

An unexpected error has occurred.

SIP_DDTS_COMP

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

SIPSPA-3-SPI4_CONFIG_FAILURE

3-Error

Bay [dec] spi4 configuration failure error [dec]

Failed to configure SPI4 interface

SIP_DDTS_COMP

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

SIPSPA-3-FCI_NOT_SET

3-Error

Bay [dec]: [chars]: FCI type not set

An FCI type of zero was detected

c7600-sip-common

LOG_STD_ACTION

SIPSPA-3-EFC_CHAN_ERR

3-Error

EFC error - interface [chars] vc [dec] anyphy [dec] err_code [dec] : [chars]

Failed to configure efc channel/parameters

SIP_DDTS_COMP

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

SIPSPA-3-INVALID_ANYPHY

3-Error

Bay [dec] - Invalid anyphy number [dec] for vc [dec]

Interface has invalid anyphy mumber

spa-ser-common

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

SIPSPA-3-LINKREC_ERROR

3-Error

Link record error - Bay [dec] vc [dec] error code [dec]

Error processing link record structure

spa-ser-common

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

SIPSPA-3-SONET_CLOCK_FAILED

3-Error

SPA Sonet clock has failed status = 0x%08x

The SPA SONET clock has failed. SPAs that rely on the SPA SONET clock for proper operation such as POS and ATM will be affected.

c7600-sip-common

"If the SPA Sonet clock does not recover perform an " "OIR. "LOG_STD_RECUR_ACTION

SIPSPA-6-ERRORRECOVER

6-Information

A Hardware or Software error occurred on [chars]. Reason : [chars] Automatic Error recovery initiated. No further intervention required.

An error occurred in one of the devices recovery would be attempted. If recovery succeeds no further messages would be logged and no intervention would be required.

c7600-sip-common

LOG_STD_RECUR_ACTION

SIPSPA-3-SONET_CLOCK_RECOVERED

3-Error

SPA Sonet clock has recovered status = 0x%08x

SPA Sonet clock has recovered

c7600-sip-common

LOG_STD_NO_ACTION

SIPSPA-3-BADCMD

3-Error

[chars]: Unsupported command [dec] arg0=[hex] arg1=[hex] arg2=[hex]

The Route Processor passed down a command that the software was not prepared to handle.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The Linecard failed to allocate a buffer for communication with the Route Processor.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The Linecard failed to send a message to the Route Processor.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-BAD_IFCOMTYPE

3-Error

Bad ifcom message type=[dec]

The Route Processor passed down a message that the software was not prepared to handle.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-MSGTOOBIG

3-Error

Message length exceeds max [dec] bytes

The Linecard attempted to send too large a message to the Route Processor.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-CMDNOINT

3-Error

HWIDB Null for command [dec] arg=[hex]

The Route Processor passed down a command that the software was unprepared to handle.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-NODISPATCH

3-Error

Dispatch vector Null cmd=[dec] dintf=[dec]

No command dispatch vector was found for the specified interface.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SIPSPA-3-BADINT

3-Error

Attempted to access HWIDB for port [dec]

The Linecard attempted to access the HWIDB associated with a non-existent port.

c7600-sip-common

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CSG-6-RELOADOK

6-Information

CSG ACCOUNTING [chars] reload on module [dec] successful

Informational message whenever a CSG configuration\n\ is reloaded as a result of power recycling a CSG card.

csg

LOG_STD_NO_ACTION

CSG-3-RELOADNOTOK

3-Error

CSG ACCOUNTING [chars] reload on module [dec] failed.

Informational message whenever a CSG configuration\n\ is reloaded as a result of power recycling a CSG card.

csg

LOG_STD_NO_ACTION

CSG-4-WARNING

4-Warning

Module [dec]: [chars]

Some possibly undesired event occurred in a CSG module.

csg

LOG_STD_RECUR_ACTION

CSG-3-ERROR

3-Error

Module [dec]: [chars]

An error occurred in a CSG module.

csg

LOG_STD_RECUR_ACTION

CSG-6-LIRELOADOK

6-Information

CSG LI reload on module [dec] successful

Informational message whenever a CSG LI configuration\n\ is reloaded as a result of power recycling a CSG card.

csg

LOG_STD_NO_ACTION

CGC-0-CGC_EMERG

0-Emergency

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-1-CGC_ALERT

1-Alert

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-2-CGC_CRIT

2-Critical

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-3-CGC_ERR

3-Error

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-4-CGC_WARNING

4-Warning

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-5-CGC_NOTICE

5-Notice

[chars]

Normal but significant conditions

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-6-CGC_INFO

6-Information

[chars]

Informational messages

CGC_DDTS_COMPONENT

LOG_STD_NO_ACTION

CGC-7-CGC_ASSERT

7-Debug

Assertion Failure [chars] @[chars]:[dec] : [chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CWMP_DOWNLOAD-5-CONFIG_SUCCESS

5-Notice

CWMP download: config file successfully downloaded and applied [chars]

The configuration apply operation with CWMP DOWNLOAD RPC\n\method is success.

-

"No action required."

CWMP_DOWNLOAD-5-CONFIG_FAILURE

5-Notice

CWMP download: config apply operation failed [chars]

The configuration apply operation with CWMP DOWNLOAD RPC\n\method is failed.

-

"No action required."

RADIO-4-NO_IMAGE

4-Warning

[chars][dec]/[dec] Chip \[chars]\: failed to find image given current configuration

Most likely configured to use external files

ubr-radiop2p-sw

"Change configuration to use internal files"

RADIO-5-IMAGE_BAD_CRC

5-Notice

[chars][dec]/[dec] detected a bad CRC while downloading image \[chars]\ to chip \[chars]\

Most likely a protocol error while downloading

ubr-radiop2p-sw

-

RADIO-5-IMAGE_TIMEOUT

5-Notice

[chars][dec]/[dec] timeout trying to open image \[chars]\ for chip \[chars]\

Most likely a protocol error while opening

ubr-radiop2p-sw

-

RADIO-6-IMAGE_NOT_FOUND

6-Information

[chars][dec]/[dec] could not find image \[chars]\ for chip \[chars]\

Most likely a typo when set the url of the image

ubr-radiop2p-sw

"Try again"

RADIO-6-SELF_TEST_SUCCESS

6-Information

Radio[dec]/0 self-test successful

Passed a self-diagnostic

ubr-radiop2p-hw

"This is a good thing"

RADIO-3-SELF_TEST_FAILED

3-Error

Radio[dec]/0 failed self-test

Most likely a hardware failure

ubr-radiop2p-hw

"Call tech support"

RADIO-4-NO_HWCAP_FIELD

4-Warning

Radio[dec]/0 could not find HW Capabilities field in IDPROM

Most likely cause is an improperly-programmed IDPROM

ubr7200

"Have the IDPROM on the linecard reprogrammed"

RADIO-4-BAD_IF_PIC

4-Warning

Radio[dec]/0 bad IF PIC version [dec] on IDU

Most likely a hardware configuration oversite

ubr-radiop2p-hw

"Call tech support"

RADIO-4-BAD_RF_PIC

4-Warning

Radio[dec]/0 bad RF PIC version [dec] on ODU [dec]

Most likely a hardware configuration oversite

ubr-radiop2p-hw

"Call tech support"

RADIO-4-NEWER_IF_EEPROM

4-Warning

Radio[dec]/0 Unsupported IF PIC major eeprom version [dec] on IDU

IOS should be upgraded to support the new eeprom

ubr-radiop2p-sw

LOG_STD_ACTION

RADIO-4-NEWER_RF_EEPROM

4-Warning

Radio[dec]/0 Unsupported RF PIC major eeprom version [dec] on ODU [dec]

LOG_STD_ACTION

ubr-radiop2p-sw

"Call tech support - upgrade IOS"

RADIO-4-IF_OSC

4-Warning

Radio[dec]/0 Internal [chars] Oscillator out of Lock [chars]

Most likely cause is vibration or hardware failure

ubr-radiop2p-hw

"Replace internal card"

RADIO-4-RF_OSC

4-Warning

Radio[dec]/0 ODU [dec] [chars] Oscillator out of Lock [chars]

Most likely cause is vibration or hardware failure

ubr-radiop2p-hw

"Replace electronics on Out Door Unit"

RADIO-4-RF_AGC

4-Warning

Radio[dec]/0 ODU [dec] max transmitter power exceeded [chars]

Most likely cause is hardware failure

ubr-radiop2p-hw

"Replace RF ODU"

RADIO-4-RF_VOLT

4-Warning

Radio[dec]/0 ODU [dec]: supply voltage out of range [chars]

Most likely cause is hardware failure

ubr-radiop2p-hw

"Replace RF ODU"

RADIO-4-RF_TEMP

4-Warning

Radio[dec]/0 ODU [dec]: temperature is [dec] degrees C threshold is [dec] degrees C

Most likely cause is hardware failure or solar heating

ubr-radiop2p-hw

"Keep the RF ODU cool"

RADIO-2-RF_OVERTEMP

2-Critical

Radio[dec]/0 ODU [dec]: over temperature [chars]

Most likely cause is hardware failure or solar heating

ubr-radiop2p-hw

"Keep the RF ODU cool"

RADIO-4-RF_ANTENNA

4-Warning

Radio[dec]/0 ODU [dec] is [chars]

Most likely cause is a disconnected cable

ubr-radiop2p-hw

"Check or replace cable from UBR to the Out Door Unit"

RADIO-4-IF_COMM

4-Warning

Radio[dec]/0 IDU IF internal serial communication error - [chars]

Most likely cause is a loose IF baby board

ubr-radiop2p-hw

"Replace hardware"

RADIO-4-RF_COMM

4-Warning

Radio[dec]/0 ODU [dec] serial communication error - [chars]

Most likely cause is a disconnected cable

ubr-radiop2p-hw

"Check or replace cable from UBR to the Out Door Unit"

RADIO-4-CHECKSUM_ERR

4-Warning

Radio[dec]/0 radio phy eeprom \[chars]\ checksum stored:0x%02x calculated:0x%02x

Most likely cause is Shut or No Shut command

ubr7200

"Enter the No Shut command"

RADIO-5-CONFIG_HW

5-Notice

Radio[dec]/0 hardware does not support requested configuration: [chars]

Most likely cause is incorrect configuration

ubr-radiop2p-sw

"Change the configuration to match the hardware"

RADIO-5-CONFIG_MISMAT

5-Notice

Radio[dec]/0 invalid or inconsistent configuration requested [chars]

Most likely cause is the ARQ settings are not supported by the current radio channel parameters

ubr7200

"Change ARQ settings to allowed values given the current radio channel parameters. You can use the radio arq reset command to do this."

RADIO-5-METRICS_THRESH

5-Notice

Radio[dec]/0 [chars] per [chars] threshold met[dec]>=[dec]

Most likely cause is a mis-aligned antenna

ubr7200

"Re-align the antennas"

RADIO-5-THRESHOLD

5-Notice

Radio[dec]/0 [chars] [chars] threshold crossed ODU [dec]

Most likely cause is a user defined threshold

ubr7200

"none"

RADIO-5-CLEAR_METRICS

5-Notice

Radio[dec]/0 link metrics cleared

User requested the link metrics be cleared

ubr7200

"none"

RADIO-4-PHY_SYNC_OK

4-Warning

Radio[dec]/0 link synchronization acquired.

Most likely cause is No Shut command

ubr7200

"None"

RADIO-4-PHY_SYNC_REOK

4-Warning

Radio[dec]/0 link synchronization re-acquired.

Most likely cause is No Shut command on remote end

ubr7200

"None"

RADIO-4-PHY_REQ

4-Warning

Radio[dec]/0 link synchronization [chars].

Most likely cause loose ODU cable

ubr7200

"Check all cables"

RADIO-4-PHY_SYNC_FAIL

4-Warning

Radio[dec]/0 link synchronization [chars].

Most likely cause loose ODU cable

ubr7200

"Check all cables"

RADIO-5-PHY_RETRY

5-Notice

Radio[dec]/0 event %23s in state %15s

Most likely cause incorrect configuration

ubr7200

"Review configuration and hardware capabilities"

RADIO-5-REMOTE_LOST_SYNC

5-Notice

Radio[dec]/0 Remote end reports: [chars]

Most likely cause cable not attached ODU overheated

ubr7200

"Check ODU cables"

RADIO-5-REMOTE_NO_SYNC

5-Notice

Radio[dec]/0 Remote end reports: Unable to acquire link synchronization.

Most likely cause cable not attached ODU overheated

ubr7200

"Check ODU cables"

RADIO-5-LOCAL_IN_SYNC

5-Notice

Radio[dec]/0 Link synchronization acquired.

Phy layer successfully acquired link.

ubr7200

"None"

RADIO-5-PHY_SYNC_LOST

5-Notice

Radio[dec]/0 Lost link. Check remote transmitter.

Most likely cause remote system is not transmitting.

ubr7200

"No Shut remote system"

RADIO-5-LOCAL_NO_SYNC

5-Notice

Radio[dec]/0 Still trying to establish link timing sync.

Most likely cause remote system is not transmitting.

ubr7200

"No Shut remote system"

RADIO-5-LOCAL_NO_FREQ

5-Notice

Radio[dec]/0 Still trying to establish link frequency sync.

Most likely cause remote system is not transmitting on correct frequency

ubr7200

"No Shut remote system"

RADIO-5-LOCAL_NO_VITERBI

5-Notice

Radio[dec]/0 Still trying to establish link viterbi sync.

Most likely cause remote system is not transmitting on correct frequency

ubr7200

"No Shut remote system"

RADIO-5-LOCAL_NO_CW

5-Notice

Radio[dec]/0 Still trying to establish link validate codeword.

Most likely cause remote system is not transmitting on correct frequency

ubr7200

"No Shut remote system"

RADIO-5-LOCAL_NO_TRANSMIT

5-Notice

Radio[dec]/0 ODU saftey interlock is preventing transmission. Check ODU and cables. [chars]

Most likely cause cable not attached ODU overheated

ubr7200

"Check ODU cable"

RADIO-4-FPGAINITPINLOW

4-Warning

Radio[dec]/0 INIT pin on FPGA \[chars]\ not asserted when PROG pin asserted

The INIT pin of a FPGA device on the RADIO line card did not assert when the PROG pin was asserted. This indicates either a faulty FPGA device or software problem resetting it.

ubr7200

LOG_STD_ACTION

RADIO-4-FPGAINITPINHIGH

4-Warning

Radio[dec]/0 INIT pin on FPGA \[chars]\ asserted during downloading

The INIT pin of a FPGA device on the RADIO line card asserted midway through the downloading of the device. Most likely cause is corrupted FPGA image.

ubr7200

LOG_STD_ACTION

RADIO-4-FPGADONEPINLOW

4-Warning

Radio[dec]/0 DONE pin on FPGA \[chars]\ did not assert after downloading

The DONE pin of a FPGA device on the RADIO line card did not assert after the downloading of the device. This probably indicates an existing or developing hardware failure.

ubr7200

LOG_STD_ACTION

RADIO-4-DSPHPITIMEOUT

4-Warning

Radio[dec]/0 HPI timeout while attempting to access DSP \[chars]\

A DSP on the RADIO line card was not granting access to its memory. Most likely cause is a DSP firmware internal error.

ubr7200

LOG_STD_ACTION

RADIO-4-DSPSPURRESP

4-Warning

Radio[dec]/0 spurious DSP response from \[chars]\: %08x %08x %08x %08x %08x %08x %08x %08x

A DSP on the RADIO line card generated a response message unexpectedly. This can happen when the router is operating under severe traffic load.

ubr7200

LOG_STD_ACTION

RADIO-4-DSPULOFLOW

4-Warning

Radio[dec]/0 uplink message queue overflow reported by DSP \[chars]\

At least one DSP-to-router message was lost due to that DSP's uplink queue being full. This can happen when many thresholds/histograms/timelines are being triggered or expiring at the same time.

ubr7200

"Change thresholds and/or reduce histogram/timeline usage to lower the load on the system"

RADIO-4-DSPINDERR

4-Warning

Radio[dec]/0 Error processing indication from DSP \[chars]\ [chars]:[dec]

A DSP on the RADIO line card generated an indication message that could not be processed. This can happen when the router is operating under severe traffic load.

ubr7200

LOG_STD_ACTION

CSM_VOICE-3-UNDEFVOICEINTRF

3-Error

Invalid interface slot:controller:group[dec]/[dec]:[dec]

The voice interface defined by slot:controller:group is not\n\ yet defined within the voice software but attempts were\n\ made to use this interface.

das

"Internal software fault. Contact your field service \n\ representative if this message is coincident with \n\ dropped calls."

CSM_VOICE-3-UNDEFDSX0

3-Error

Undefined dsx0 interface for controller[dec]/[dec]

The dsx0 interface for the specified controller\n\ is not defined but the voice software use it.

das

"Internal software fault. Contact your field service representative \n\ if this message is coincident with dropped calls."

CSM_VOICE-3-NOSDB

3-Error

No signaling data block is available to build the \n\ voice interface[dec]/[dec]:[dec]

The voice software was unable to obtain a signaling data\n\ block from the Voice Telephony Service Provider. \n\ The system may be out of memory.

das

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-ADDINTRFFAIL

3-Error

The Voice Telephony Service Provider has rejected our\n\ request to add this voice interface [dec]/[dec]:[dec]

The voice software was unable to report a new signaling\n\ interface to the Voice Telephony Service Provider

das

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-NOMEM

3-Error

No memory is available to build the voice interface [dec]:[dec]

The voice software was unable allocate memory to build \n\ a voice interface data structure. The system may be \n\ out of memory.

das

LOG_STD_SH_TECH_ACTION

CSM_VOICE-3-MALLOC

3-Error

No memory is available to build any internal data \n\ structure for the voice software.

The voice software was unable allocate memory to build \n\ any internal data structures. The system may be \n\ out of memory.

das

LOG_STD_SH_TECH_ACTION

DSCREDCLK-5-BNORMAL

5-Notice

Backup clock moving to NORMAL to phase lock to active clock

The backup DSC has detected a change to the clock

-

LOG_STD_NO_ACTION

DSCREDCLK-5-BSWITCHT

5-Notice

Backup clock matched to active clock reference slot [dec] line [dec]

The backup DSC has detected a change in the selected clock reference \ on the active DSC and has changed it's own clock hardware to match \ the new selection. \ The selected clock reference is now from the specified trunk line.

-

LOG_STD_NO_ACTION

DSCREDCLK-5-BSWITCHE

5-Notice

Backup clock matched to active clock reference external clock on DSC

The backup DSC has detected a change in the selected clock reference \ on the active DSC and has changed it's own clock hardware to match \ the new selection. \ The selected clock reference is now from the DSC front panel external \ clock feed.

-

LOG_STD_NO_ACTION

DSCREDCLK-2-BACTFAIL

2-Critical

Clock on other DSC has failed - immediate clock takeover

The backup DSC clock has detected failure on the other DSC clock \ hardware \ and is taking over to become the active clock manager.

-

LOG_STD_ACTION

DSCREDCLK-2-BACTGONE

2-Critical

Removal of other DSC detected - immediate clock takeover

The backup DSC clock has detected removal of the other DSC \

-

"Reinstall a DSC in other DSC slot to provide DSC."

DSCREDCLK-3-BACTIOSF

3-Error

Other DSC IOS keepalive failure - clock takeover

The other DSC has failed to respond to keepalives to the current \ DSC and so the current DSC is taking over to become the active \ clock manager.

-

"Recover DSC in other DSC slot to provide backup DSC."

DSCREDCLK-2-BCLKCMDFAIL

2-Critical

Clock command hardware failed

The

-

LOG_STD_ACTION

DSCREDCLK-3-BTAKEDELAY

3-Error

Active DSC requests backup to takeover clock - delaying for sync

The other DSC has requested the current DSC to take over active \ clock management \ but the current DSC is waiting for clock hardware synchronization \ before doing so to avoid call loss.

-

LOG_STD_NO_ACTION

DSCREDCLK-3-BTAKEOVER

3-Error

Active DSC requests backup to takeover clock - done

-

-

""

DSC_REDUNDANCY-3-DSIP_TX_ERR

3-Error

reliable IPC msg not tx'd by DSIP on [chars]

-

-

""

DSC_REDUNDANCY-3-BAD_ROLE

3-Error

illegal red. entity role [dec] found in history queue by [chars]

-

-

""

DSC_REDUNDANCY-3-BAD_ASPECT

3-Error

illegal red. entity history aspect [dec] passed to [chars]

-

-

""

DSC_REDUNDANCY-3-Q_EMPTY

3-Error

expected [dec] elements in queue but found none

-

-

""

DSC_REDUNDANCY-3-BAD_STATE

3-Error

unexpected [chars] state in [chars]

-

-

""

DSC_REDUNDANCY-3-EVENT

3-Error

Redundancy event: [chars]

-

-

""

DSC_REDUNDANCY-3-STATUSCHANGE

3-Error

DSC in slot [dec] [chars]

-

-

""

DSC_REDUNDANCY-3-BICLINK

3-Error

[chars]

-

-

""

DSC_REDUNDANCY-3-MODECONFLICT

3-Error

Other DSC/router in split mode

There is another router connected to the dial shelf. In this situation\n\ both must be configured in split mode

-

"Configure the other router in split mode"

DSC_REDUNDANCY-3-SLOTCONFLICT

3-Error

Slot ownership conflict detected for slot [dec]

There is another router connected to the dial shelf it is claiming\n\ ownership of a slot that this router is also claiming

-

"Fix the ownership conflict by reconfiguring one of the routers\n\ so that it doesn't own the slot"

DSC_REDUNDANCY-3-TDMSPLITCONFLICT

3-Error

Tdm Split conflict detectedmy tdm [dec] other rs [dec]

There is another router connected to the dial shelf it is claiming\n\ ownership of backplane timeslots that this router requires. This is probably due to\n\ OIR activity moving trunk cards from one half of the split to the other.

-

"Fix the ownership conflict by reloading the router whose tdm number\n\ is greater than the trunk capacity for that router. In some cases\n\ it may be necessary to reset both routers."

FREEDM-3-INITFAIL

3-Error

Freedm [chars] initialization failed: [chars]

Freedm device failed initialization

-

""

FREEDM-3-NOTFREEDM

3-Error

Freedm [chars] returned device/vendor of [hex]

PCI get device id returned an unrecognized value

-

""

FREEDM-3-BUSYTIMEOUT

3-Error

Freedm [chars] busy bit of register 0x[hec] never cleared

Driver timedout waiting for the Freedm to acknowlege a request

-

""

FREEDM-2-FATALEVENT

2-Critical

Freedm [chars] fatal event occured: 0x[hec]

A catastrophic Freedm error occured

-

""

FREEDM-3-HDLC_INUSE

3-Error

Freedm [chars]: HDLC controller [dec] already in use on channel [dec]

An attempt was made to use an HDLC controller which was already in use

-

""

FREEDM-3-HDLC_ALLOC_FAIL

3-Error

Freedm [chars]: Allocation of HDLC controller [dec] for channel [dec] failed

Allocation of an HDLC controller failed

-

""

KINEPAK-3-NODSPENTRY

3-Error

No dsp entry in dsp list

The software structure that is used to maintain the DSP \n\ instance is missing.

-

LOG_STD_RECUR_ACTION

KINEPAK-3-NORXPAK

3-Error

Static receive paktype unavailable

A software structure was found in an unexpected state during\n\ run-time for the indicated DSP.

-

LOG_STD_ACTION

KINEPAK-3-CONTIGUOUS

3-Error

Contiguous packet sent for transmit

A software error occurred resulting in an unexpected packet being\n\ set up for transmission and the packet was dropped.

-

LOG_STD_RECUR_ACTION

KINEPAK-3-NOPARTICLE

3-Error

No particle available for ingress packet

A software error occurred resulting in failure to obtain a \n\ particle to hold an ingress packet from DSP.

-

LOG_STD_RECUR_ACTION

KINEPAK-3-NOPARTICLEPOOL

3-Error

Cannot create particle pool

A software error occurred resulting in failure to create a \n\ particle pool to receive packets from DSP.

-

LOG_STD_ACTION

KINEPAK-3-NOMAILELEMENTS

3-Error

Cannot create message buffer

A software error occurred resulting in failure to create a \n\ message buffer to send messages among processes.

-

LOG_STD_ACTION

KINEPAK-3-ERR_DSPWARE_DNLD

3-Error

dsp[dec] cannot download dspware [chars]

A software error occurred resulting in failure to download a \n\ dspware component.

-

LOG_STD_ACTION

KINEPAK-3-ERR_DSPWARE_IMG

3-Error

Cannot find dspware [chars] component

A software error occurred resulting in failure to download a \n\ dspware component.

-

LOG_STD_ACTION

TRUNK-3-BADMSG

3-Error

Bad doorbell message type to framer: [dec]

An invalid or undefined message type was sent to the framer\n\ processor.

-

LOG_STD_ACTION

TRUNK-3-INITFAIL

3-Error

Trunk card initialization failed due to: [chars]

The memory buffer for message passing between the trunk card and\n\ framer processors has been exhausted. Either the messages are not\n\ being picked up or are being generated too quickly.

-

LOG_STD_ACTION

TRUNK-3-BADFW

3-Error

Invalid framer firmware code file.

The software has detected an invalid framer firmware image that\n\ cannot be downloaded.

-

LOG_STD_ACTION

TRUNK-3-HBEAT

3-Error

No longer receiving heartbeats from framer CPU.

Communication from the framer processor to the trunk card processor\n\ has stopped. The framer processor is no longer passing status to\n\ the trunk card processor nor accepting messages from the trunk card \n\ processor.

-

LOG_STD_ACTION

TRUNK-3-MSGTMOUT

3-Error

Timed out waiting for framer CPU to respond.

The framer processor did not reply to the read request during a\n\ specified amount of time.

-

""

TRUNK-3-BADCLOCK

3-Error

selected clock on slot [dec] port [dec] is bad.Accepting the config.

The clock status as reported by the framer is bad. Either no cable\n\ is plugged in or the port is indeed bad. Configuration is accepted\n\ and as soon as the port in reference turns good it will be \n\ applied.

-

"If user is configuring the clocks configuration in advance while\n\ there is no card in the corresponding slot or no cable is plugged\n\ in yet and if he is aware of this fact then there is no action that\n\ needs to be taken. Otherwise choosing another good clock and\n\ troubleshooting the bad clock from the port in reference is \n\ receommended."

DS_TDM-3-TDM_OPEN

3-Error

Slot [dec]: open MT90820 addr: 0x[hec] connection failed -

An attempt to establish a digitally-switched connection failed.

-

""

DS_TDM-3-TDM_CLOSE

3-Error

Slot [dec]: close MT90820 addr: 0x[hec] connection failed - STo[dec] CHo[dec]

An attempt to disable a digitally-switched connection failed.

-

""

DS_TDM-3-CONV_OPEN

3-Error

Slot [dec]: open MT8986 addr: 0x[hec] [chars] connection failed -

An attempt to establish a rate converted connection failed.

-

""

DS_TDM-3-CONV_CLOSE

3-Error

Slot [dec]: open MT8986 addr: 0x[hec] connection failed - STo[dec] CHo[dec]

An attempt to disable a rate converted connection failed.

-

""

DS_TDM-3-BAD_CONN

3-Error

Slot [dec]: unrecognized TDM connect message received [dec] on

An unrecognized TDM connect message was received.

-

""

DS_TDM-3-BAD_DISCONN

3-Error

Slot [dec]: unrecognized TDM disconnect message received [dec] on

An unrecognized TDM disconnect message was received.

-

""

DS_TDM-3-BAD_DSIP

3-Error

Slot [dec]: unrecognized DSIP message received [dec] on [chars] feature board

An unrecognized DSIP message was received.

-

""

DS_TDM-3-VERIFY_IMS

3-Error

Slot [dec]: [chars] failed to veryify IMS: 0x[hec]

An attempt to verify a TDM hardware component failed.

-

""

DS_TDM-3-VERIFY_HILOWMEM

3-Error

Slot [dec]: [chars] failed to veryify himem or lowmem: sto = [dec] ch_out = [dec] sti = [dec] ch_in = [dec]

An attempt to verify a TDM hardware component failed.

-

""

DS_TDM-3-VERIFY_DISCONN

3-Error

Slot [dec]: [chars] failed to veryify disconnect: sto = [dec] ch_out = [dec]

An attempt to verify a TDM hardware component failed.

-

""

DS_TDM-3-ASSERT_FAIL

3-Error

Slot [dec]: Assertion failed: file `[chars]' line [dec]

An internal sanity check failed.

-

""

DS_TDM-3-BAD_MAPPING

3-Error

Slot [dec]: Legacy FB [chars] with static port-to-DS0 mapping

A software error lead to dynamic port-to-DS0 mapping info being passed to a statically-mapped FB.

-

""

DS_TDM-3-UNEXPECTED_INT

3-Error

Slot [dec]: got unexpected interrupt from masked-out source '[chars]'

An interrupt was received from the specified source despite it being masked-out.

-

""

DS_TDM-3-S4_INT

3-Error

Slot [dec]: [chars] generated interrupt [chars]

Raiko-based FB's TDM Mezzanine card has no free Recombination bus DS0s.

-

""

DS_TDM-3-RECOMB_BUS_TS_BAD_USE

3-Error

Slot [dec]: convention broken for Mezz's Recomb. bus t'slots: [chars]-st%02u-ts%03u/gts>%04u><%04u</[chars]-st%02u-ts%03u

-

-

""

DS_TDM-3-DISC_FOR_NO_CONN

3-Error

Slot [dec]: got disc msg for non-existent conn: [chars]-st%02u-ts%03u/gts>%04u><%04u</[chars]-st%02u-ts%03u

The FB was asked to disconnect a connection that it didn't know about.

-

""

DS_TDM-3-UNSUPPORTED_MEZZ_VER

3-Error

Slot [dec]: the detected version [dec] of Mezzanine card is not

The software does not support the Mezzanine card currently installed on the Raiko card.

-

""

DS_TDM-3-BAD_S4_POWER_UP

3-Error

Slot [dec]: [chars] powered-up with one or more incorrect default settings [chars]

-

-

""

RS_TDM-3-TDM_NOT_SPLIT_PAIR

3-Error

TDM split user setting are not matched pairs my RS [chars] = [dec] ds0 expected other RS [chars] = [dec] ds0 actual other RS [chars] = [dec] ds0

The user setting for tdm split on this router shelf is not compatible with the setting on the other router

as5800

"Set the other router dial-shelf split backplane-ds0 to above setting"

RS_TDM-3-TDM_CONFLICT

3-Error

TDM split user setting are in conflict: my RS [chars] = [dec] other RS [chars] = [dec]

The user setting for tdm split on this router shelf is in conflict with the setting on the other router More backplane DS0 are in usethan 2048 DS0

as5800

"Set the other router dial-shelf split backplane-ds0 to non conflicting setting"

RS_TDM-3-TDM_REDUCED_TDM_SPLIT

3-Error

TDM split on [chars] Router shelf Reduced to [dec] backplane ds0

The number of backplane ds0 for this router has been forced lower

as5800

""

RS_TDM-3-TDM_EXTEND_CLASH

3-Error

TDM extended split on Router shelf Clashes to my [chars] other [chars] extended backplane ds0

The number of extended backplane ds0 for this router clashes with the other router shelf

as5800

""

RS_TDM-3-TDM_LEG_CLASH

3-Error

TDM legacy split on Router shelf Clashes to my [dec] other [dec] legacy backplane ds0

The number of legacy backplane ds0 for this router clashes with the other router shelf

as5800

""

RS_TDM-3-TDM_BACKPLANE_CLASH

3-Error

Clash in usage for TDM backplane timeslot [dec]

The TDM backplane timeslot to be allocated is already in use

as5800

"Check the split dial-shelf settings on both router shelves for conflicting setting"

RS_TDM-3-TDM_UNKNOWN_TS_STATE

3-Error

TDM backplane timeslot [dec] is in an unknown state

The TDM backplane timeslot specified is in an unknown state

as5800

"Check the split dial-shelf settings on both router shelves for conflicting setting"

RS_TDM-3-TDM_BADARG

3-Error

A TDM function is used with a bad argument: [chars]

An internal software error has occurred. A TDM function was called with invalid arguments and could not be processed. The invalid arguments are specified at the end of this error message along with any other useful data.

as5800

"Enter the <CmdBold>debug tdm<NoCmdBold> command. If the problem " "recurs copy the error message the trace message and surrounding debug text " "exactly as they appear on the console or in the system log call your Cisco " "technical support representative and provide the representative with " "the gathered information."

MODEM-1-BADEVENT

1-Alert

Invalid modem management [chars] event 0x%02x for modem[chars]

The modem management facility received an unrecognize event.

-

LOG_STD_ACTION

MODEM-4-BADMODEMS

4-Warning

Modems [chars] and [chars] failed back-to-back test: [chars]

The two modems reported in the message failed a back-to-back test.\n\ At least one of them has failed.

-

"Perform more back to back tests by pairing the failed modems with\n\ other modems to determine which modem is bad. Check the failed\n\ modems again after performing a power cycle. " LOG_STD_RECUR_ACTION

MODEM-5-B2BMODEMS

5-Notice

Modems [chars] and [chars] completed back-to-back test: success/packets = [dec]/[dec]

The reported modems have passed the back to back test without any\n\ errors.

-

LOG_STD_NO_ACTION

MODEM-1-BADMODEM

1-Alert

Modem [chars] failed [chars]

A software or hardware problem has been detected on a modem.\n\ The specific modem and reason are listed in the message.

-

LOG_STD_ACTION

MODEM-5-MODEM_OK

5-Notice

Modem [chars] passed the test

Tests on the specified modem were successful.

-

LOG_STD_NO_ACTION

MODEM-5-B2BCONNECT

5-Notice

Modems [chars] and [chars] connected in back-to-back test: [chars]

A back to back test connection has been made between the selected\n\ modems. The test is still in progress.

-

LOG_STD_NO_ACTION

MODEM-3-PWDNLDPROC

3-Error

Portware download manager process start-up failed

The attempt to start up the portware download manager process at\n\ initialization time failed and so portware download requests cannot\n\ be handled.

-

LOG_STD_ACTION

MODEM-5-DL_START

5-Notice

Modem [chars] started firmware download

The specified modem has begun downloading its internal microcode.

-

LOG_STD_NO_ACTION

MODEM-5-DL_GOOD

5-Notice

Modem [chars] completed firmware download: [chars]

The specified modem has succeeded downloading its internal microcode.

-

LOG_STD_NO_ACTION

MODEM-1-DL_FAIL

1-Alert

Firmware download failed for slot [dec] module_mask [hec]

The modem modules did not send back an Initialized message\n\ after the download.

-

LOG_STD_ACTION

MODEM-1-DL_FAIL_BADFREE

1-Alert

Item to be freed is in queues [chars]. Slot [dec] module_mask 0x[hec]

The attempt to free the dnld info structure was aborted.

-

LOG_STD_ACTION

MODEM-1-DL_FAIL_FILE_XFER

1-Alert

Firmware download failed for slot [dec] module_mask 0x[hec] due to file transfer error

The download of a portware file to the modem card over DSIP as\n\ part of a modem firmware upgrade attempt timed out and failed\n\ to complete successfully

-

"LOG_STD_ACTION"

MODEM-1-DL_PROC_FAIL

1-Alert

Portware download process creation failed

-

-

"LOG_STD_ACTION"

MODEM-1-DL_LOSS_FAIL

1-Alert

Firmware download failure for slot [dec] module [dec]

The portware download for the module was previously deferred\n\ but when later ready to be performed the information needed\n\ for the download had been lost

-

""

MODEM-4-NO_TIME_FOR_DC

4-Warning

Warning -- Not enough time to process DC session

-

-

LOG_STD_RECUR_ACTION

MODEM-3-UNEXPECTED_STATUS_EV

3-Error

Error -- status state machine received unexpected event=[dec] for modem[chars]

The modem management subsystem's status-polling state machine\n\ received an undefined event for or from the specified modem.

-

LOG_STD_ACTION

MODEM-3-UNEXPECTED_STATUS_STATE

3-Error

Error -- status state machine in unknown state=[dec] for modem[chars]

The modem management subsystem's status-polling state machine\n\ for the specified modem entered an undefined state.

-

LOG_STD_ACTION

MODEM-5-MODEM_RECOVERY

5-Notice

Modem [chars] [chars]

Modem recovery has been triggered. Configured action will\n\ take place on given modem

-

""

MODEM-5-MODEM_RECOVERY_DL

5-Notice

Slot [dec] Module [dec]: [chars]

Module download information

-

""

MODEM-5-MODEM_RECOVERY_PROCESS

5-Notice

[chars]

Modem Recovery Process information

-

""

MODEM-5-CONFIG

5-Notice

Configurations \fast-answer\ and \country [chars]\ conflict.\n Configuration \fast-answer\ disabled.

The fast-answer configuration conflicts with the country setting.\n\ The country was given priority and fast-answer was disabled.

-

LOG_STD_NO_ACTION

MODEM-3-MODEM_INFO_CREATE_FAIL

3-Error

Unable to create modem infos for slot [dec]

During OIR of this board the modem infos attempted to be created but failed due to lack of memory

-

"If this message is seen then save the output of show memory showing\n\ the amount of processor and IO memory usage only along with show\n\ version and call your technical support representativ for\n\ assistance."

MODEM-3-MODEMSTART_OUTOFMEM

3-Error

Error -- Unable to allocate memory to startup modem board in slot [dec]

Running out of memory during modem board startup.

-

"If this message is seen then save the output of show memory showing\n\ the amount of processor and IO memory usage only along with show\n\ version and call your technical support representativ for\n\ assistance."

MODEM-3-BADMODEMNUM

3-Error

Error: Trying to access an invalid modem [dec]

The requested operation could not be accomplished because of a bad modem number. Call your technical support representative for assistance

modem-management

LOG_STD_ACTION

PW_WATCHER-3-NO_RESPONSE_STARTUP_REQ

3-Error

Portware Watcher detected a missing modem board startup message for slot [dec]. Resetting the slot

The slot did not send a startup msg after a given amount of retries\n\ requesting it. This can happen if after a router shelf reload the\n\ feature was not redownloaded with a new image and the NIP_MODEM_MNGR\n\ client's port was not reinitialised correctly and stayed closed. This\n\ should not be considered a critical problem by the customer as\n\ it should not affect the operation of the router.

-

"Copy the output of the message as well as a description of events\n\ leading up to the message and open a DDTS."

PW_WATCHER-6-UNEXPECTED_DOWNLOAD

6-Information

Portware Watcher detected an unregistered module download in slot [dec] module [dec].

This is an informational message indicating that the portware watcher\n\ process had not been initialised with the slot and module information\n\ to monitor the download. This in no way affects the operation of the\n\ module or the system in general and should not be considered a \n\ serious problem.

-

"Copy the output of the message as well as a description of events\n\ leading up to the message and open a DDTS."

MODEM_HIST-7-TRACE_HDR

7-Debug

\n\n[chars] Modem [chars] Events Log:

This is the initial message for the trace of the specified modem.\n\ The modem's stored trace messages will follow.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-STARTUP

7-Debug

\n[chars]: Startup Response: [chars]. \nModem boot firmware = [dec].[dec].[dec] [dec].[dec].[dec]

This is a tracing message indicating successful startup of the\n\ specified modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-CONTROL

7-Debug

\n[chars]: Control Reply: 0x%02x%02x

This is a tracing message indicating a reply to a control message\n\ was received.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_TX_RX

7-Debug

\n[chars]: TX/RX event: TXD=[chars] RXD=[chars]

This is a tracing message indicating transmit and receive events.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_RS232

7-Debug

\n[chars]: RS232 event: [chars][chars] [chars][chars] [chars][chars] [chars][chars] [chars][chars] [chars][chars] [chars][chars]

This is a tracing message indicating RS232 events.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_MODEM_STATE

7-Debug

\n[chars]: Modem State event: [chars]

This is a tracing message indicating a modem state change.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_CONN_1

7-Debug

\n[chars]: Connection event: TX/RX Speed = [dec]/[dec] Modulation = [chars]

This is a tracing message indicating establishment of a connection.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_CONN_2

7-Debug

\n Direction = [chars] Protocol = [chars] Compression = [chars]

This is a continuation of the connection state tracing message.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_CONX_UPDATE

7-Debug

\n[chars]: Connection update event: TX/RX Speed = [dec]/[dec] Modulation = [chars]

This is a tracing message indicating a connection state change.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_PROGRESS

7-Debug

\n[chars]: Call Progress event: [chars]

This is a tracing message indicating status of a call in progress.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_DTR

7-Debug

\n[chars]: DTR event: [chars]

This is a tracing message indicating a change in the DTR signal.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_INACT

7-Debug

\n[chars]: Modem Activity event: [chars]

This is a tracing message indicating a change in data activity\n\ status.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_ANALOG

7-Debug

\n[chars]: Modem Analog signal event: TX = [dec] RX = [dec] Signal to noise = [dec]

This is a tracing message indicating a change in analog signal\n\ status.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_END_1

7-Debug

\n[chars]: End connection event: Retransmits for MNP block TX/RX = [dec]/[dec]

This is a tracing message indicating end-of-connection status.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_END_2

7-Debug

\n Duration = [dec]:%-02d:%-02d Number of TX/RX char = [dec]/[dec]

This is a continuation of the end-of-transmission status message.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_END_3

7-Debug

\n Local Disc Reason = [chars] Remote Disc Reason = [chars]

This is another continuation of the end-of-transmission status\n\ message.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_NO_RESP

7-Debug

\n[chars]: No poll response event: 0x%02x

This is a tracing message indicating that no response was received\n\ to a poll.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_EVT_LOST

7-Debug

\n[chars]: Status event lost: 0x%02x

This is a tracing message indicating a polling event was lost.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_PHONE

7-Debug

\n[chars]: Phone number event: [chars]

This is a tracing message indicating a phone number being dialed.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_CALLER_ID

7-Debug

\n[chars]: Caller ID event: [chars]

This is a tracing message indicating caller ID data received.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_ERROR

7-Debug

\n[chars]: Polling protocol error event: 0x%02x

This is a tracing message indicating a polling protocol error.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-POLL_UNKNOWN

7-Debug

\n[chars]: Unknown or lost event 0x%02x

This is a tracing message indicating that the modem event history\n\ contained an unrecognized event. One or more events may be missing\n\ from the trace.

-

"This could be caused by insufficient space to store the modem\n\ history. If these events are desirable a possible remedy is to\n\ shorten the number of events recorded between history dumps. " LOG_STD_REDUCE_ACTION

MODEM_HIST-7-UNKNOWN_FRAME

7-Debug

\n[chars]: Error in events log

This is a tracing message indicating a formatting error in the\n\ modem event history. One or more events may be missing from\n\ the trace.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-CSM_OC_CALLED_NUM

7-Debug

\n[chars]: ISDN outgoing called number: [chars]

This is a tracing message indicating a dialed ISDN number.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-CSM_IC_CALLING_NUM

7-Debug

\n[chars]: ISDN incoming caller number: [chars]

This is a tracing message indicating the number of an incoming\n\ ISDN caller.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-CSM_IC_CALLED_NUM

7-Debug

\n[chars]: ISDN incoming called number: [chars]

This is a tracing message indicating the number of the ISDN\n\ line recieving a call.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_STARTUP_EVT

7-Debug

\n[chars]: [chars] [chars]. \n%*s Modem firmware = [dec].[dec].[dec].[dec]

This is a tracing message indicating successful startup of the\n\ specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_STATUS_EVT

7-Debug

\n[chars]: [chars]: [chars]. \n%*s Modem firmware = [dec].[dec].[dec].[dec]

This is a tracing message indicating a status event reported by\n\ the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_STATIC_EVT

7-Debug

\n[chars]: [chars]: [chars]

This is a tracing message indicating a static event reported by\n\ the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_DYNAMIC_EVT

7-Debug

\n[chars]: [chars]: [chars]

This is a tracing message indicating a dynamic event reported by\n\ the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_END_CONN_EVT

7-Debug

\n[chars]: [chars]: [chars]

This is a tracing message indicating an end-connection event\n\ from the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_OOS_EVT

7-Debug

\n[chars]: [chars] \n%*s Cause: [chars]

This is a tracing message indicating an out-of-service event\n\ from the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_STATE_EVT

7-Debug

\n[chars]: [chars] \n%*s State: [chars]

This is a tracing message indicating a state event reported by\n\ the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_LEAD_EVT

7-Debug

\n[chars]: [chars]: [chars] [chars] [chars] [chars]

This is a tracing message indicating a lead event reported by\n\ the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM_HIST-7-MICA_DEBUG_EVT

7-Debug

\n[chars]: [chars]:

This is a tracing message indicating a host debug event reported by\n\ the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM-5-B2BINIT

5-Notice

Auto Back-to-Back test initiated by [chars]

This is a tracing message indicating an automatic back-to-back\n\ test was initiated by the specified MICA modem.

-

LOG_STD_DBG_ACTION

MODEM-4-B2BABORT

4-Warning

Modems [chars] and [chars] back-to-back test: aborted

This is a tracing message indicating a back-to-back test\n\ failed between the two specified MICA modems.

-

"Perform more back to back tests by pairing the failed modems with\n\ other modems to determine which modem is bad. Check the failed\n\ modems again after performing a power cycle. " LOG_STD_RECUR_ACTION

TTYDRIVER-3-BADENCAP

3-Error

Unknown encapsulation on interface [chars]

A software error occurred resulting in an unknown encapsulation\n\ type on the interface specified by the error message.

-

LOG_STD_ACTION

TTYDRIVER-3-NOPARTS

3-Error

No particles available to set up for output on tty [chars]

A software error occurred resulting in an unexpected exhaustion\n\ of the pool of data buffers used by the modem drivers.

-

LOG_STD_ACTION

TTYDRIVER-3-NOTXPART

3-Error

Non-zero outcount but no transmit particle on tty [chars]

A software error occurred resulting in an invalid state for the\n\ RTS modem signal

-

LOG_STD_ACTION

TTYDRIVER-3-UNKNOWN_PORT_ARCH_TYPE

3-Error

Unknown port type [dec]

A software error occurred due to an unrecognised port type

-

LOG_STD_ACTION

CALLRECORD-6-MICA_TERSE_CALL_REC

6-Information

[chars]

Terse Mica Call Record

modem-management

LOG_STD_NO_ACTION

CALLRECORD-6-MICA_TERSE_CALL_FAILED_REC

6-Information

[chars]

Terse Mica Call Failed Record

modem-management

LOG_STD_NO_ACTION

CALLRECORD-3-MODEM_CALL_REC_ERROR

3-Error

[chars]

Record Generated Exceeded Syslog Capability

modem-management

LOG_STD_NO_ACTION

TRUNK-3-NOMEM

3-Error

Insufficient memory for slot: [dec] in shelf: [dec]

This message indicates that the router's memory was exhausted while\n\ allocating memory for use with the specified slot and shelf.

-

LOG_STD_REDUCE_ACTION

TRUNK-3-BADCARDTYPE

3-Error

Unknown type 0x[hec] in shelf [dec] slot [dec]

An internal software error occurred. An attempt was made to\n\ reference a shelf number larger than the installed maximum.

-

LOG_STD_ACTION

TRUNK-3-DROP

3-Error

T1 Port [dec] on slot [dec] is now in drop-insert mode.

The user has dropped a T1 port on a CT3 card by pressing the \n\ pushbutton on the CT3 card. This is a disruptive action in that\n\ any existing calls will be dropped.

-

""

TRUNK-3-NODROP

3-Error

T1 Port [dec] on slot [dec] taken out of drop-insert mode.

The user has restored a T1 port on a CT3 card by pressing the \n\ pushbutton on the CT3 card. This port was earlier dropped by\n\ the user and has now been taken out of dropped mode.

-

""

CSM-1-INITFAIL

1-Alert

[chars]

-

-

""

CSM-1-INVALID_DC_NUMBER

1-Alert

Initialization failed with invalid digit collector count

-

-

""

CSM-1-INITPORTFAIL

1-Alert

Initialization of vdev [dec]/[dec]/[dec] failed

-

-

""

CSM-1-DCHAN_ALLOC_FAIL

1-Alert

For channel [chars]

-

-

""

CSM-1-CAS_ALLOC_FAIL

1-Alert

Fail to add new signal channel [dec]/[dec] timeslot [dec]

-

-

""

CSM-3-NO_VDEV

3-Error

No modems associated:[chars]Chan[dec]Id[dec]

-

-

""

CSM-1-NO_HWIDB

1-Alert

No B channel associated with call

-

-

""

CSM-1-NO_CSM_CALL_INFO

1-Alert

No call control block

-

-

""

CSM-1-NEW_RBS_CHAN

1-Alert

A new RBS channel added

-

-

""

CSM-1-CSM_CALL_INFO_MISMATCH

1-Alert

csm_call_info contains\n\ mismatch information call info has [chars]:[dec] framer gives [dec]/[dec]:[dec]

-

-

""

CSM-1-CSM_CALL_NO_RESOURCE

1-Alert

Failed to allocate resource for call from [dec]/[dec]:[dec]

-

-

""

CSM-1-CSM_STRING_OVERRUN

1-Alert

String copy exceeded buffer size

The string written into the allocated buffer exceeded the size of\n\ the buffer. This can cause memory corruption.

-

LOG_STD_ACTION

FB_COREDUMP-3-NOMEMORY

3-Error

No Memory or buffer for [chars] to be send to [dec]

Sufficient memory was unavailble for Router Shelf to send any command or \n\ acknowledment to the feature boards.

-

LOG_STD_ACTION

MICA-3-PORTWARE

3-Error

Bad version [chars] portware: [chars]

Modem firmware of the indicated version bundled into the modem \n\ card image did not pass the sanity tests done to verify a \n\ firmware image.

-

LOG_STD_ACTION

MICA-3-BADIMAGE

3-Error

Cannot download version [chars] on module [dec]

The block information that is necessary to download modem firmware\n\ was missing for the indicated firmware version.

-

LOG_STD_ACTION

MICA-3-NOENTRIES

3-Error

Exhausted [chars] DMA entries for module [dec]

-

-

LOG_STD_RECUR_ACTION

MICA-3-PWDNLDTO

3-Error

Portware download timed out for module [dec]

The diagnostic message that is expected back from a MICA modem\n\ after successful download and initialization of the modem firmware\n\ was never received.

-

LOG_STD_ACTION

MICA-6-INIT

6-Information

Modem module [dec] initialized

The indicated modem module was successfully initialized.

-

LOG_STD_NO_ACTION

MICA-3-BADRXCOUNT

3-Error

Bad count from modem [dec]: count = [dec]

A message was received from the indicated modem which had an\n\ illegal count .

-

LOG_STD_RECUR_ACTION

MICA-3-BADRXOPCODE

3-Error

Bad mail message opcode from modem [dec]: opcode = 0x[hec]

A message was received from the indicated modem which had an\n\ illegal opcode.

-

LOG_STD_RECUR_ACTION

MICA-3-BADTXOPCODE

3-Error

Bad tx mail message opcode = 0x[hec]

A message was attempted to be transmitted to the indicated\n\ modem which had an illegal opcode.

-

LOG_STD_RECUR_ACTION

MICA-3-NOMAILELEMENTS

3-Error

Exhausted free mail elements for modem_num [dec]. Current use: [dec]

The software structures that are used to receive and transmit\n\ messages from the MICA modems were temporarily exhausted.

-

LOG_STD_RECUR_ACTION

MICA-3-BADPARAM

3-Error

Modem [dec]: [chars] while handling [chars].

The modem state machine received a bad parameter as indicated\n\ by the error message.

-

LOG_STD_RECUR_ACTION

MICA-3-NOTTY

3-Error

No TTY structure for modem [dec]

A software structure was found in an unexpected state during\n\ run-time for the indicated modem.

-

LOG_STD_ACTION

MICA-3-NOIDB

3-Error

No IDB structure for modem [dec]

A software structure was found in an unexpected state during\n\ run-time for the indicated modem.

-

LOG_STD_ACTION

MICA-3-NOPPPCTX

3-Error

No PPP context structure for modem [dec]

A software structure was found in an unexpected state during\n\ run-time for the indicated modem.

-

LOG_STD_ACTION

MICA-3-NOTPLX

3-Error

Bad vendor id from PLX 9060SD -- value was 0x[hec]

A hardware error occurred involving the PCI interface chip.

-

LOG_STD_ACTION

MICA-3-CRASH

3-Error

Runtime error on MICA module [dec] Hex [dec]

A software error occurred on the modem firmware executing on the\n\ indicated modem module.

-

LOG_STD_ACTION

MICA-3-NAK

3-Error

NAK from modem [dec] in state [dec] -- payload 0x[hec]

A message sent to the indicated modem was rejected.

-

LOG_STD_RECUR_ACTION

MICA-3-BADMODEM

3-Error

Modem [dec] went bad

Run-time checks for modem health determined that the indicated modem\n\ was no longer functional due to a hardware or software error.

-

LOG_STD_RECUR_ACTION

MICA-3-RESTART

3-Error

Attempting restart of modem module [dec]

The indicated modem module suffered a run-time error and had to \n\ be reset and an attempt is now being made to restart the modem \n\ module.

-

LOG_STD_NO_ACTION

MICA-3-NORXPAK

3-Error

Static receive paktype unavailable

A software structure was found in an unexpected state during\n\ run-time for the indicated modem.

-

LOG_STD_ACTION

MICA-3-CONTIGUOUS

3-Error

Contiguous packet sent for transmit

A software error occurred resulting in an unexpected packet being\n\ set up for transmission and the packet was dropped.

-

LOG_STD_RECUR_ACTION

MICA-3-TXDESCLIMIT

3-Error

Packet descriptor count [dec] exceeds transmit ring size

The packet to be transmitted needed more descriptors than are\n\ available on the transmit ring and the packet was dropped.

-

LOG_STD_RECUR_ACTION

MICA-3-BADMODULE

3-Error

Module in socket [dec] is of unknown type board-id=[dec]

The modem module in the socket indicated by the message is\n\ inappropriate for the modem card it is on.

-

LOG_STD_SH_TECH_ACTION

MICA-3-INBANDNAK

3-Error

Inband NAK from modem [dec] -- payload 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec]

A inband message sent to the indicated modem was rejected.

-

LOG_STD_RECUR_ACTION

MICA-3-INBAND_UNKNOWN_OPCODE

3-Error

Inband message with unknown opcode received from modem [dec] -- payload 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec] 0x[hec]

An inband message with unknown opcode was received from the \n\ indicated modem

-

LOG_STD_RECUR_ACTION

MICA-3-INVALID_PARAM

3-Error

Mica sent invalid stack address or length MICA module [dec] addr 0x[hec] length [dec]

Runtime error occured on MICA MICA sent invalid stack address or \n\ length.

-

LOG_STD_ACTION

MICA-3-NOMEMORY

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

MICA-3-BADMODEMNUM

3-Error

Error: Trying to access an invalid modem [dec]

The requested operation could not be accomplished because of a bad modem number. Call your technical support representative for assistance

modem-management

LOG_STD_ACTION

DS_MODEM-3-BADCB

3-Error

Unexpected DSIP data callback for modem

An unexpected software event occurred.

-

LOG_STD_ACTION

DS_MODEM-3-NORXPAK

3-Error

Static receive paktype unavailable

Temporarily unable to allocate particle for sending traffic to\n\ modem module indicates a break down of flow control between RS-DS.

-

LOG_STD_ACTION

DS_MODEM-3-FLOW_CONTROL

3-Error

DS-RS flow control has got out of sync connection has too many particles free.\n\ slot:[dec] ttynum:[dec] parts_avail:[dec]

Indicates the flow control accounting on the DS has got out of sync.\n\

-

LOG_STD_ACTION

M32X-3-PANIC

3-Error

M32X: Exception [dec] trace [dec]

A software or hardware error has occurred in the M32X trunk card.

-

LOG_STD_ACTION

M32X-3-TOOSMALL

3-Error

M32X: [chars] - packet was less than two bytes

An output packet was detected that was smaller than the minimum\n\ allowable datagram size. An error in another driver or an error in \n\ the system software probably triggered this error message.

-

LOG_STD_ACTION

M32X-3-MBXREAD

3-Error

M32X: Stale msg in [chars] - mbx0:%lx mbx1:%lx mbx2:%lx

The M32X has not responded to a message within a specified time.

-

LOG_STD_ACTION

M32X-3-NOTM32X

3-Error

Device reported [hex]

A hardware error occurred involving the PCI interface for\n\ an M32X trunk card.

-

"If it is an M32X trunk card then this is due to a malfunction.\n\ Or another PCI device may have been mistaken for an M32X. " LOG_STD_ACTION

M32X-1-NOTREADY

1-Alert

Not ready for download.

The M32X trunk card did not respond when commanded to\n\ download its operational microcode.

-

"Perform a power cycle. " LOG_STD_RECUR_ACTION

M32X-1-DWNLDFL

1-Alert

M32X down load failed.

The M32X trunk card failed. It could not download its \n\ operational microcode.

-

"Perform a power cycle. " LOG_STD_RECUR_ACTION

M32X-1-DWNLDCKSM

1-Alert

M32X: Download checksum error sent = 0x[hec] received = 0x[hec]

The download of the internal microcode to the M32X failed to\n\ checksum correctly. This usually indicates a hardware failure of\n\ the M32X.

-

"Perform a power cycle. " LOG_STD_RECUR_ACTION

M32X-1-NOTCMPLT

1-Alert

M32X download failed to complete.

The M32X trunk card has failed. It could not download its\n\ operational microcode.

-

LOG_STD_ACTION

M32X-1-INITFAIL

1-Alert

M32X slot [dec]: Init Failed at [chars]

The M32x trunk card failed to complete hardware\n\ initialization.

-

LOG_STD_ACTION

M32X-1-STARTFAIL

1-Alert

[chars]: Channel enable failed

A software or hardware error occurred. The M32X trunk card\n\ is not responding to commands used to initialize it.

-

LOG_STD_ACTION

M32X-1-STOPFAIL

1-Alert

[chars]: Channel disable failed

A software or hardware error occurred. The M32X trunk card\n\ failed to respond to a request to disable an interface.

-

LOG_STD_ACTION

M32X-5-REMLOOP

5-Notice

M32X controller [dec] channel [dec]: remote loopback [chars] [chars]

The interface entered or exited a remote loopback.

-

LOG_STD_NO_ACTION

M32X-1-AR_TIMEOUT

1-Alert

M32X controller [dec] channel 0x[hec]: No Reponse from device. Action Request Timeout

The Action Request for a particular has failed after retry.

-

LOG_STD_NO_ACTION

DSCCLOCK-5-SWITCH1

5-Notice

Clock moving to NORMAL from FREERUN selected clock is on slot [dec] port [dec] line [dec]

The primary TDM clock which has been running off the \n\ local oscillator of DSC in FREERUN mode has switched to the line \n\ clock coming in via the specified trunk.

-

LOG_STD_ACTION

DSCEXTCLK-5-SWITCH1

5-Notice

Clock moving to NORMAL from FREERUN selected clock is external clock on DSC

The primary TDM clock which has been running off the \n\ local oscillator of DSC in FREERUN mode has switched to the \n\ external network reference clock being fed from the DSC front\n\ panel.

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH2

3-Error

Clock moving to FREERUN from HOLDOVER

The current primary TDM clock has been deleted and hence the\n\ system primary has switched to the DSC local oscillator which\n\ is the current highest priority good clock. \n\ Phase continuity is maintained during the switchover.

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH3

3-Error

Clock moving to NORMAL from HOLDOVER selected clock is on slot [dec] port [dec] line [dec]

The current primary TDM clock has been deleted and hence the\n\ system primary has switched to the clock coming in via the\n\ trunk specified by the slot/port which is the current \n\ highest priority good clock. Phase continuity is maintained \n\ during the switchover.

-

LOG_STD_ACTION

DSCEXTCLK-3-SWITCH3

3-Error

Clock moving to NORMAL from HOLDOVER selected clock is external clock on DSC

The current primary TDM clock has been deleted and hence the\n\ system primary has switched to the clock coming in via the\n\ external network reference clock on the DSC front panel which \n\ is the current highest priority good clock. Phase \n\ continuity is maintained during the switchover

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH4

3-Error

Switching to the user configured clock on slot [dec] port [dec] line [dec]

-

-

LOG_STD_ACTION

DSCEXTCLK-3-SWITCH4

3-Error

Switching to the user configured external clock on DSC

-

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH5

3-Error

Switching to the clock on slot [dec] port [dec] line [dec]

The TDM primary clock is switching to the clock coming in via\n\ the trunk specified most likely after the router-shelf\n\ and hence feature boards reload. The phase of the output TDM \n\ clock is forced to align with the input reference during the \n\ switchover.

-

LOG_STD_ACTION

DSCEXTCLK-3-SWITCH5

3-Error

Switching to the external clock on DSC

The TDM primary clock is switching to the clock coming in via\n\ the DSC front panel most likely after the router-shelf\n\ and hence feature boards reload. The phase of the output TDM \n\ clock is forced to align with the input reference during the\n\ switchover.

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH6

3-Error

Switching to the clock on slot [dec] port [dec] line [dec] as the current primary has gone bad

The TDM primary clock has switched to a backup clock coming in \n\ via the specified trunk as the current primary clock has gone\n\ bad.

-

LOG_STD_ACTION

DSCEXTCLK-3-SWITCH6

3-Error

Switching to the external clock on DSC as the current primary has gone bad

The TDM primary clock has switched to a backup clock coming in \n\ via the DSC front panel external clock feed as the current primary \n\ clock has gone bad.

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH7

3-Error

Moving to NORMAL mode from HOLDOVER mode clock is slot [dec] port [dec] line [dec]

The TDM primary clock which is in HOLDOVER mode and whose source \n\ was a trunk port has switched to the same trunk port and moved\n\ to NORMAL mode with a phase alignment between input \n\ source clock and output TDM reference clock. Most likely the \n\ router-shelf and hence the feature boards have reloaded.

-

LOG_STD_ACTION

DSCEXTCLK-3-SWITCH7

3-Error

Moving to NORMAL mode from HOLDOVER mode selected external clock on DSC

The TDM primary clock which is in HOLDOVER mode and whose source \n\ was a the DSC front panel clock has switched to the same clock \n\ and moved to the NORMAL mode.

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH8

3-Error

Moving to NORMAL mode from HOLDOVER mode without phase correction clock is slot [dec] port [dec] line [dec]

The source trunk port of the TDM primary clock which had gone bad \n\ has turned good again before the holdover timer expiry. Hence the \n\ primary has moved from HOLDOVER to NORMAL state without phase \n\ correction between input trunk reference and the output TDM clock.

-

LOG_STD_ACTION

DSCEXTCLK-3-SWITCH8

3-Error

Moving to NORMAL mode from HOLDOVER mode without phase correction selected external clock on DSC

The DSC front panel clock which is the source of the current TDM \n\ primary clock and which had gone bad has turned good again before \n\ the holdover timer expiry. Hence the primary has moved from HOLDOVER \n\ to NORMAL state without phase correction between input reference and \n\ the output TDM clock.

-

LOG_STD_ACTION

DSCCLOCK-3-SWITCH_ERROR1

3-Error

Failed to select any clock as the system clock. Remaining in HOLDOVER mode

The clock selection algorithm has failed to select any clock as \n\ the TDM primary clock.

-

LOG_STD_ACTION

DSCCLOCK-3-FAIL

3-Error

The System Primary Clock is down. Moving to HOLDOVER state and waiting to see if it comes up

This message is generated whenever the current primary clock \n\ goes bad. The TDM clock circuit goes into HOLDOVER mode and \n\ a holdover timer is started to see if the bad clock turns \n\ good within the holdover time.

-

LOG_STD_ACTION

DSCCLOCK-3-UP

3-Error

The System Primary Clock is up. Moving to NORMAL state from HOLDOVER

The TDM primary clock which had gone bad has turned good within\n\ the holdover time. Hence the TDM primary clock switches to the \n\ NORMAL mode from the HOLDOVER mode.

-

LOG_STD_ACTION

DSCCLOCK-3-NOMEMORY

3-Error

Failed to allocate memory for the DSC clocks

The clock switching software has failed to allocate memory\n\ while adding a clock.

-

LOG_STD_ACTION

DSCCLOCK-3-DUP_PRI

3-Error

Duplicate priority [dec] clock sources: slot [dec] port [dec] and slot [dec] port [dec].

-

-

LOG_STD_ACTION

DIALSHELF-2-UNDEFCARD

2-Critical

Card type [dec] in slot [dec]

The software does not have a driver for the card in specified\n\ slot.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIALSHELF-2-DSCDOWN

2-Critical

DSC in slot [dec] changes state to down.

DSC in dial shelf went down.

-

-

DIALSHELF-3-SLOTSTATUS

3-Error

Invalid change from [chars] [dec] to [chars] [dec] for slot [dec]

The software detected an invalid state change for the specified\n\ slot. This is a software error.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIALSHELF-3-EVENT

3-Error

Unknown event [dec] for slot [dec]

The software generated an unknown event for the specified\n\ slot. This is a software error.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIALSHELF-3-MSG

3-Error

Unknown message type [dec] from DSC

The router shelf received an unknown message from the DSC in\n\ the dial shelf. This is a software error or compatibility issue.\n\ Check the software versions on the router shelf and the DSC.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIALSHELF-3-INVALIDMSG

3-Error

[chars] [dec]

The router shelf received an invalid message from the DSC in\n\ the dial shelf. This is a software error or compatibility issue.\n\ Check the software versions on the router shelf and the DSC.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIALSHELF-2-TIMEOUT

2-Critical

[chars] slot [dec] after [dec] secs in state '[chars]'

The specified dial shelf slot timed out as per the message.\n\ Either a software or a hardware component has failed.

-

"Try removing and reinserting the card. If that does not help\n\ try a different card. If problem persists contact your\n\ technical support representative."

DIALSHELF-4-UNRECOMMENDED

4-Warning

Number of [chars] may exceed recommended configuration

On NPE200 more than one CT3 or more than two T1/E1 are installed\n\ this exceeds the recommended configuration.

-

"Stay within recommended limit of CT3/T1/E1 or install split \n\ dial-shelf configuration or upgrade router-shelf to NPE300."

DIALSHELF-6-RELOAD

6-Information

Reload requested for card in shelf [dec] slot [dec].

The command \'hw-module slot <shelf>/<slot> reload\' was entered.\n\ This is a confirmation that the command is being processed.

-

"None"

DSIP-3-RANGE

3-Error

DSIP parameter range error [chars] [dec]

-

-

""

DSIP-3-NO_MAJOR_VERSION

3-Error

Client addition to DSIP has failed [chars] [dec]

-

-

""

DSIP-3-CLIENT_ADD_FAIL

3-Error

Adding client [dec] after DSIP has started.

-

-

""

DSIP-3-IPC_SEAT

3-Error

IPC subsystem API error can not create seat by \n\ the seatid [dec] for the slot [dec]

Nitro Interconnect Protocol reliable stack \n\ has failed to create seat for the specified slot.

-

""

DSIP-3-IPC_CLIENT

3-Error

IPC subsystem API error[chars] [chars] [dec]

-

-

""

DSIP-3-IPC_PORT

3-Error

IPC subsystem API error[chars] [chars] [chars]

-

-

""

DSIP-3-TXCONTEXT

3-Error

[chars] slot [dec] client [dec]

\n\

-

""

DSIP-3-TXCONTEXT_ACTIVE_USE

3-Error

Waiting for the active transmit contexts to become inactive

\n\

-

""

DSIP-3-INTRAPI_BUF_MALLOC_FAILURE

3-Error

Failed to get memory for the DSIP interrupt api buffers

\n\

-

""

DSIP-3-VERSBUF_MALLOC_FAILURE

3-Error

Failed to get memory for the DSIP version buffers

\n\

-

""

DSIP-3-VERSDBASE_MALLOC_FAILURE

3-Error

Failed to get memory for the DSIP version database

\n\

-

""

DSIP-3-CLIVERSDBASE_MALLOC_FAILURE

3-Error

Failed to get memory for the DSIP clicnets version database

\n\

-

""

DSIP-3-GET_INTRAPI_BUF_FAILURE

3-Error

Failed to get interrupt api buffers

\n\

-

""

DSIP-3-GET_VERSBUF_FAILURE

3-Error

Failed to get version buffers

\n\

-

""

DSIP-3-PRIVPOOL

3-Error

Failed to create DSIP private buffer pool

\n\

-

""

DSIP-3-GETPAK

3-Error

Failed to get packet buffer

\n\

-

""

DSIP-3-INCOMPATIBLE_CLIENT

3-Error

Incompatible client [chars] on DS slot [dec] with major version [dec] and minor version [dec]. Shutting down all the DSIP clients on this slot

-

-

""

DSIP-3-CLIENT_VERSION_MISMATCH

3-Error

Some clients on this feature board are running versions which are incompatible with RS. Not initializing any DSIP clients. You can find the incompatible clients by executing the show dsip version command

-

-

""

DSIPPF-5-RS_KEEPALIVE_LOSS

5-Notice

DSIP Keepalive Loss from router shelf [dec]

-

-

""

DSIPPF-5-DS_HELLO

5-Notice

DSIP Hello from shelf [dec] slot [dec] Succeeded

-

-

""

DSIPPF-5-DS_KEEPALIVE_LOSS

5-Notice

DSIP Keepalive Loss from shelf [dec] slot [dec]

-

-

""

DSIPPF-5-RS_HELLO

5-Notice

DSIP Hello from router shelf [dec] Succeeded

-

-

""

DSIPPF-5-HELLO_ERROR

5-Notice

DSIP Hello from shelf [dec] slot [dec] failed due to DSIP version mismatch

-

-

""

DSIPPF-3-BASE_FTBL_MALLOC_FAIL

3-Error

Failed to allocate memory for the base fucntion table

-

-

""

DSIPPF-3-DSIP_SEND_FAILURE

3-Error

Failed to send DSIP message - number of failures [dec]

This message indicates that Nitro Interconnect Protocol\n\ has encountered an error while sending a message and that the\n\ message has been discarded after three unsuccessful resends.

-

""

SNASW-3-ASSERT

3-Error

Assertion failure : '[chars]' from [chars] line [dec]

-

-

-

SNASW-3-TRACE

3-Error

Diagnostic trace record too large for configured buffer. Buffer ID [hec]

A cyclic trace buffer could not be resized due to insufficient\n\ memory. The previously allocated buffer if any will continue\n\ to be used.

snasw

"Reconfigure a smaller buffer-size for the specified buffer type."

SNASW-3-BAD_MSG_NAME

3-Error

Invalid message name specified for sna\sw msg-trap

An invalid message name was supplied on a snasw msg-trap command.

snasw

"Reissue the command with a valid message name."

SNASW-3-EVENT

3-Error

[chars]

Informational event

snasw

"None - informational only"

SNASW-3-PD_NBA_LOG_0

3-Error

Handle was not freed

-

-

-

SNASW-3-PD_NBA_LOG_20

3-Error

Memory block still in use at termination time

-

-

-

SNASW-3-PD_NBA_LOG_21

3-Error

Memory management inconsistency

-

-

-

SNASW-3-PD_NBA_LOG_22

3-Error

Memory management inconsistency

-

-

-

SNASW-3-PD_NBA_LOG_23

3-Error

Memory management inconsistency

-

-

-

SNASW-3-PD_NBA_LOG_24

3-Error

Memory management inconsistency

-

-

-

SNASW-3-PD_NBA_LOG_25

3-Error

Memory management inconsistency

-

-

-

SNASW-3-DEBUG_LOG_0

3-Error

PROBLEM - %lu - SNA Switch DEBUG log [chars]

SNA Switch Debug log.

snasw

"Report to SNA Switch technical support."

SNASW-3-RM_LOG_0

3-Error

PROBLEM - %lu - Insufficient storage to start TP instance and conversation requested by received Attach [chars]

Insufficient storage to start the transaction program instance\n\ and conversation requested by a received Attach FMH5.\n\msgdef_recommended_action Either decrease the system load

-

-

SNASW-3-RM_LOG_3

3-Error

PROBLEM - %lu - Insufficient storage to start conversation requested by [MC_]ALLOCATE or CMALLC [chars]

Insufficient storage to start a new conversation requested by\n\ ALLOCATE MC_ALLOCATE or CMALLC.\n\ [MC_]ALLOCATE will fail with primary_rc of\n\ NAP_UNEXPECTED_SYSTEM_ERROR or\n\ CMALLC with fail with return_code of CM_PRODUCT_SPECIFIC_ERROR

snasw

-

SNASW-3-CLS_LOG_0

3-Error

PROBLEM - %lu - Could not validate process handle [chars]

CLS has passed SNA Switch a DLC packet but SNA Switch does not have a valid\n\ handle to invoke the correct SNA process. The CLS message has been \n\ discarded.

snasw

"Dump traces and contact the Cisco TAC."

SNASW-4-RM_LOG_13

4-Warning

EXCEPTION - %lu - APPC Transaction Program or CPI-C application has ended abnormally with active conversations [chars]

An APPC transaction program or CPI-C application has ended\n\ abnormally with active conversations. This usually indicates\n\ an error in the application.\n\ SNA Switch will deactivate all sessions currently being used by\n\ the application.

snasw

"Run a trace on the APPC API or the CPI-C API to see the\n\ sequence of verbs causing the problem."

SNASW-3-RM_LOG_14

3-Error

PROBLEM - %lu - Deactivating session because of insufficient storage [chars]

Deactivating session because of insufficient storage.\n\ SNA Switch will deactivate the session.

snasw

-

SNASW-3-RM_LOG_15

3-Error

PROBLEM - %lu - Insufficient storage to initiate session activation requested by [MC_]ALLOCATE or CMALLC [chars]

Insufficient storage to initiate session activation requested\n\ by ALLOCATE MC_ALLOCATE or CMALLC.\n\ [MC_]ALLOCATE will fail with primary_rc of NAP_ALLOCATION_ERROR\n\ and secondary_rc of NAP_ALLOCATION_FAILURE_NO_RETRY.\n\ CMALLC will fail with return_code of\n\ CM_ALLOCATION_FAILURE_NO_RETRY

snasw

-

SNASW-3-RM_LOG_22

3-Error

PROBLEM - %lu - LU-LU verification failed. [chars]

LU-LU verification failed. The partner LU has sent an incorrect\n\ response to a challenge sent by a local LU. This is either a\n\ security attack or a defect in the software at the partner LU\n\ location.\n\ The session will be deactivated.

snasw

"Check the identity of the partner LU. If this is a defect in\n\ the software at the partner LU location then contact support."

SNASW-4-RM_LOG_23

4-Warning

EXCEPTION - %lu - Insufficient storage to deactivate limited resource session [chars]

Insufficient storage to deactivate limited resource session.\n\ The limited resource session will not be deactivated although\n\ it may be deactivated later. This could result in limited\n\msgdef_recommended_action Either decrease the system load

-

-

SNASW-6-RM_LOG_27

6-Information

INFO - %lu - Session limits changed [chars]

The session limits for a local LU partner LU and mode have\n\ changed. The termination count indicates the number of\n\ sessions SNA Switch will deactivate as a result of the change\n\ in session limits.

snasw

"None"

SNASW-3-RM_LOG_37

3-Error

PROBLEM - %lu - LU-LU verification protocol error [chars]

LU-LU verification protocol error. This may indicate an\n\ interoperability problem.\n\ The session will be deactivated with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-RM_LOG_42

3-Error

PROBLEM - %lu - Failed to activate a new session since this would exceed LU or mode session limit [chars]

SNA Switch was unable to activate a new session because the\n\ maximum session limit specified for the mode or the local LU\n\ would be exceeded.\n\ ALLOCATE MC_ALLOCATE or CMALLC verbs will either fail or hang\n\ waiting for a session to become free.

snasw

"Wait for a session to become free and retry or use a different\n\ mode."

SNASW-3-RM_LOG_43

3-Error

PROBLEM - %lu - Insufficient storage to start TP instance requested by TP_STARTED [chars]

Insufficient storage to start the transaction program instance\n\ requested by TP_STARTED.\n\ If other instances of the same transaction program are active\n\ SNA Switch will queue the TP_STARTED waiting for one of them to\n\ become free. Otherwise the TP_STARTED verb will fail with\n\ primary_rc of NAP_UNEXPECTED_SYSTEM_ERROR.

snasw

-

SNASW-3-RM_LOG_44

3-Error

PROBLEM - %lu - Insufficient storage to initiate automatic session activation [chars]

Insufficient storage to initiate automatic session activation.\n\ Fewer active sessions will be available on the specified mode\n\ which may cause application delays or failures.

snasw

-

SNASW-3-RM_LOG_45

3-Error

PROBLEM - %lu - Insufficient storage to initiate session activation requested by ACTIVATE_SESSION [chars]

Insufficient storage to initiate session activation requested\n\ by ACTIVATE_SESSION verb.\n\ ACTIVATE_SESSION will fail with NAP_ACTIVATION_FAIL_NO_RETRY

snasw

-

SNASW-3-RM_LOG_46

3-Error

PROBLEM - %lu - Bracket protocol error [chars]

Bracket protocol error. This may indicate a problem in the\n\ partner LU. The sense codes are as follows.\n\ 20080000 - partner LU attempted to start bracket after\n\ sending BIS\n\ 20030000 - partner LU attempted to start bracket after local\n\ LU had BID for session successfully or\n\ unexpected RTR request received\n\ 20100000 - Received negative response to BID with sense code\n\ 088B0000 from a partner LU who supports parallel\n\ sessions or\n\ BIS protocol error\n\ The session will be deactivated with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-RM_LOG_47

3-Error

PROBLEM - %lu - Attach protocol error [chars]

Attach protocol error. This may indicate a problem in the\n\ partner LU. The sense codes are as follows\n\ 080F6051 - Attach security protocol violation\n\ 10086011 - LUW identifier format error or\n\ LUW identifier not specified when sync level is\n\ syncpt\n\ 10086040 - sync level not supported by session or\n\ already-verified not accepted from partner LU\n\ 10086031 - PIP not allowed by TP\n\ The session will be deactivated with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-RM_LOG_48

3-Error

PROBLEM - %lu - Attach rejected because security information invalid [chars]

Attach rejected because security information invalid. This\n\ indicates an attempt to access a secure TP by an unknown user\n\ or a known user who has specified an incorrect password.\n\ The Attach will be rejected.

snasw

"Use the information in the log to locate the attempted security\n\ violation."

SNASW-3-RM_LOG_49

3-Error

PROBLEM - %lu - Attach rejected because requested sync level not supported by requested transaction program [chars]

Attach rejected because the specified sync level is not\n\ supported by the specified transaction program. This may be\n\ a mismatch in the capabilities of the originating transaction\n\ program and the destination transaction program or it may\n\ simply be a configuration error.\n\ The Attach will be rejected.

snasw

"Check the sync level supported by the specified transaction\n\ program and check that it matches the sync_level defined for\n\ the transaction program. If they match or the transaction\n\ program is not defined there is a mismatch between the\n\ originating and destination transaction programs."

SNASW-3-RM_LOG_50

3-Error

PROBLEM - %lu - Attach rejected because requested TP is temporarily disabled [chars]

Attach rejected because the specified TP is temporarily\n\ disabled.\n\ The Attach will be rejected.

snasw

"This condition is not currently supported by SNA Switch so this\n\ log should not occur."

SNASW-3-RM_LOG_51

3-Error

PROBLEM - %lu - Attach rejected because requested TP is permanently disabled [chars]

Attach rejected because the specified TP is permanently\n\ disabled. This should only occur if an application has\n\ explicitly disabled the transaction program.\n\ The Attach will be rejected.

snasw

"Collect trace and contact support."

SNASW-3-RM_LOG_52

3-Error

PROBLEM - %lu - Failed to activate a new session because mode name was not recognized [chars]

SNA Switch was unable to activate a new session because the\n\ mode name specified was not recognized.\n\ ALLOCATE MC_ALLOCATE or CMALLC verbs will fail.

snasw

"Check the mode name."

SNASW-3-RM_LOG_53

3-Error

PROBLEM - %lu - Attach rejected because security information not specified [chars]

Attach rejected because security information not specified.\n\ This indicates an attempt to access a secure TP without\n\ specifying a user ID or password.\n\ The Attach will be rejected.

snasw

"Use the information in the log to locate the security mismatch"

SNASW-3-RM_LOG_54

3-Error

PROBLEM - %lu - Bracket protocol error [chars]

BIS protocol error. This may indicate a problem in the\n\ partner LU. The sense code is always set to 20100000.\n\ The session will be deactivated with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-CS_LOG_0

3-Error

PROBLEM - %lu - An active link station has failed [chars]

An active link station has failed.\n\ The link and any sessions using it will be deactivated

snasw

"Attempt to restart the link. If the problem persists inspect\n\ the log for problems or exceptions logged by the DLC which give\n\ more specific reasons for the failure and follow the actions\n\ specified by those logs. Otherwise run a trace on the\n\ specified port or link station to find the reason for the\n\ failure."

SNASW-3-CS_LOG_1

3-Error

PROBLEM - %lu - XID exchange count exceeds activation limit [chars]

The number of XIDs received during link activation exceeded\n\ the limit defined for the port. This could indicate an XID\n\ protocol error or an excessively unreliable physical media.\n\ The sense data gives more information about the error.\n\ 083E0001 - the limit was exceeded while exchanging\n\ prenegotiation or negotiation XIDs\n\ 0809003A - the limit was exceeded while exchanging NULL XIDs.\n\ Link activation will fail.

snasw

"Retry the activation. If SNA Switch is still\n\ unable to activate the link station run a trace on the link\n\ station or port to diagnose the problem."

SNASW-3-CS_LOG_2

3-Error

PROBLEM - %lu - XID exchange count exceeds nonactivation limit [chars]

The number of XIDs received during non-activation exchange\n\ exceeded the limit defined for the port. This could indicate\n\ an XID protocol error or an excessively unreliable physical\n\ media.\n\ Non-activation XID exchange will fail and the link will be\n\ deactivated.

snasw

"Run a trace on the link station or port to diagnose the\n\ problem and contact support with trace information."

SNASW-3-CS_LOG_3

3-Error

PROBLEM - %lu - Insufficient storage to activate link [chars]

Insufficient storage to activate link.\n\ Link activation will fail.

snasw

-

SNASW-3-CS_LOG_4

3-Error

PROBLEM - %lu - Link to back-level LEN node not configured [chars]

An XID3 from an adjacent back-level LEN node ie. not carrying\n\ a network name control vector was received and there was not a\n\msgdef_recommended_action Define a link station

-

-

SNASW-3-CS_LOG_5

3-Error

PROBLEM - %lu - Link to host not configured correctly host is not a Type 2.1 node [chars]

Link to host not configured correctly that is\n\ configured as a link to a Type 2.1 node.\n\msgdef_recommended_action Redefine

-

-

SNASW-3-CS_LOG_6

3-Error

PROBLEM - %lu - XID protocol error during activation exchange [chars]

-

snasw

"Contact support with details of the problem."

SNASW-3-CS_LOG_7

3-Error

PROBLEM - %lu - No free TG numbers [chars]

No free TG numbers between this node and the specified adjacent\n\ node. This should only occur if there are already 236 parallel\n\ TGs between this node and the adjacent node.\n\ Link activation will fail.

snasw

"Re-configuring the network to reduce the number of parallel TGs\n\ between this node and the specified adjacent node."

SNASW-3-CS_LOG_8

3-Error

PROBLEM - %lu - XID protocol error during non-activation exchange [chars]

XID protocol error during non-activation exchange. This may\n\ indicate an interoperability problem between this node and the\n\ adjacent node. The sense codes are as follows.\n\ 0809003A - received a null XID when an activation XID\n\ format 3 was expected\n\ 0809003B - received a null XID when a nonactivation XID\n\ format 3 was expected\n\ 0809003E - activation XID received when non-activation XID\n\ expected\n\ 0809003F - adjacent node initiated a secondary-initiated\n\ non-activation XID exchange on a link that does\n\ not support secondary-initiated non-activation XID\n\ exchanges\n\ 08090042 - nonactivation exchange initiation indicator not\n\ set when expected\n\ 0809004E - received a non-null XID from a secondary NRM\n\ link station when a null XID was expected\n\ 10160002 - adjacent node has been inconsistent in its setting\n\ of ACTPU suppression indicator\n\ 10160008 - adjacent node has been inconsistent in its setting\n\ of networking capabilities\n\ 1016000B - adjacent node attempted to change TG number during\n\ nonactivation exchange to a TG number that was\n\ already in use\n\ 10160019 - adjacent node has attempted to change its CP name\n\ when CP-CP sessions supported on link station or\n\ link station not quiesced\n\ The link will be deactivated.

snasw

"Run a trace on the link station or port to obtain more\n\ diagnostic information on the problem. Contact support with\n\ details of the log and trace."

SNASW-3-CS_LOG_9

3-Error

PROBLEM - %lu - Link to host not configured correctly host is not a DSPU [chars]

Link to host not configured correctly that is\n\ configured as a link to a DSPU.\n\msgdef_recommended_action Redefine

-

-

SNASW-3-CS_LOG_10

3-Error

PROBLEM - %lu - Link to host not configured [chars]

An unexpected SET_MODE ie. received before XID exchange had\n\ completed was received from an adjacent host and there was not\n\msgdef_recommended_action Define a link station

-

-

SNASW-3-CS_LOG_11

3-Error

PROBLEM - %lu - Parallel TGs not supported to this adjacent node [chars]

Attempted to activate more than one TG to an adjacent node that\n\ does not support parallel TGs.\n\ Link activation will fail.

snasw

"Modify the configuration so that there is only one link station\n\ defined to the specified adjacent node. Alternatively\n\ several links to the adjacent node can be defined but only one\n\ can be active concurrently."

SNASW-4-CS_LOG_12

4-Warning

EXCEPTION - %lu - Insufficient storage to perform orderly link deactivation link deactivated immediate instead [chars]

Insufficient storage to perform orderly link deactivation\n\ performing immediate deactivation instead.\n\ None.

snasw

-

SNASW-3-CS_LOG_13

3-Error

PROBLEM - %lu - Conflicting requirements for error recovery link is not HPR-capable [chars]

Conflicting requirements for error recovery between the local\n\ node and a partner node when attempting to activate a link that\n\ is HPR-capable.\n\ Link will activate but will not be HPR-capable.

snasw

"To allow HPR protocols to be used on the link the local and\n\ partner nodes must be able to accommodate the other's error\n\ recovery requirement. At the minimum this will require\n\ reconfiguration but may not always be possible."

SNASW-4-CS_LOG_14

4-Warning

EXCEPTION - %lu - Insufficient storage to update ANR routing tables following deactivation of an HPR-capable link [chars]

Insufficient storage to update ANR routing tables following\n\ deactivation of an HPR-capable link.\n\ The node may not be able to free resources that are no longer\n\ required but will otherwise operate normally.

snasw

-

SNASW-4-CS_LOG_15

4-Warning

EXCEPTION - %lu - Insufficient storage to update ANR routing tables following activation of an HPR-capable link [chars]

Insufficient storage to update ANR routing tables following\n\ activation of an HPR-capable link.\n\ HPR traffic using this ANR label will not be routed correctly\n\ which may cause RTP connections to path-switch or fail\n\ altogether.

snasw

-

SNASW-3-CS_LOG_17

3-Error

PROBLEM - %lu - DLC failed [chars]

A DLC has ended abnormally.\n\ All ports and link stations defined on the DLC will be\n\ inoperative.

snasw

-

SNASW-4-CS_LOG_19

4-Warning

EXCEPTION - %lu - Insufficient storage to forward Alert generated by DLC [chars]

Insufficient storage to forward Alert generated by DLC.\n\ Alert will be discarded.

snasw

-

SNASW-3-CS_LOG_22

3-Error

PROBLEM - %lu - Unable to deactivate port [chars]

Unable to deactivate port.\n\ snasw stop port will fail port may not restart successfully.

snasw

"If required attempt to restart the port. If this fails look\n\ for DLC specific logs giving more information on the reason\n\ for the failure."

SNASW-3-CS_LOG_24

3-Error

PROBLEM - %lu - Unrecoverable DLC failure [chars]

Unrecoverable DLC failure.\n\ The DLC will be destroyed and all ports and link stations\n\ defined on the DLC will be inoperative.

snasw

-

SNASW-4-CS_LOG_25

4-Warning

EXCEPTION - %lu - Link not configured for automatic activation or last stopped non-automatically [chars]

A session or application required SNA Switch to automatically\n\ activate a link station but the link station was not\n\ configured to be automatically activated or was last stopped\n\ non-automatically.\n\ The session or application will fail with the specified sense\n\ code.

snasw

-

SNASW-4-CS_LOG_26

4-Warning

EXCEPTION - %lu - Unable to activate link station because owning port is not active [chars]

-

snasw

"If possible increase the port link-activation limits.\n\ Otherwise check the consistency of the network topology."

SNASW-4-CS_LOG_27

4-Warning

EXCEPTION - %lu - Unable to find requested link [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-4-CS_LOG_28

4-Warning

EXCEPTION - %lu - Unable to activate dynamic link station because owning port is not active [chars]

-

snasw

"If possible increase the port activation limits. Otherwise\n\ check the consistency of the network topology."

SNASW-4-CS_LOG_29

4-Warning

EXCEPTION - %lu - Unable to find requested connection network [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-3-CS_LOG_30

3-Error

PROBLEM - %lu - Incoming call rejected because port link-activation limits exceeded [chars]

An incoming call was rejected because the port link-activation\n\ limits would be exceeded.\n\ The link activation will fail.

snasw

"If possible increase the port link-activation limits."

SNASW-3-CS_LOG_31

3-Error

PROBLEM - %lu - The CP name on an XID3 received from adjacent node is different to that expected [chars]

The CP name on an XID3 received from an adjacent node is\n\ different to that expected.\n\ The link activation will fail.

snasw

"If the received adjacent CP name is correct correct the link\n\ station configuration using snasw link. Depending on other\n\ aspects of the link station definition the CP name check\n\ can be disabled by issuing snasw link with the adj_cp_name field\n\ set to all zeros."

SNASW-3-CS_LOG_32

3-Error

PROBLEM - %lu - The node ID on an XID3 received from a back-level node is different to that expected [chars]

The node ID on an XID3 received from a back level node is\n\ different to that expected.\n\ The link activation will fail.

snasw

"If the received node ID is correct correct the link station\n\ configuration using snasw link. Depending on other aspects of\n\ the link station definition the node ID check can be disabled\n\ by issuing snasw link with the adj_node_id field set to all\n\ zeros."

SNASW-3-CS_LOG_33

3-Error

PROBLEM - %lu - The node type indicated on an XID3 received from an adjacent node is different to that expected [chars]

The node type indicated on an XID3 received from an adjacent\n\ node is different to that expected.\n\ The link activation will fail.

snasw

"If the received node type is correct correct the link station\n\ configuration using snasw link. Depending on other aspects of\n\ the link station definition the node type check can be disabled\n\ by issuing snasw link with the adj_node_type field set to\n\ NAP_LEARN_NODE."

SNASW-3-CS_LOG_34

3-Error

PROBLEM - %lu - Both sent and received XIDs indicate the same non-negotiable link station role [chars]

Both sent and received XIDs indicate the same non-negotiable\n\ link station role.\n\ The link activation will fail.

snasw

"Either correct the local port definition or the remote\n\ definition so that the link station roles are complementary\n\ or at least one link station is negotiable."

SNASW-4-CS_LOG_35

4-Warning

EXCEPTION - %lu - Unable to activate link station because port total link-activation limit reached [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-4-CS_LOG_36

4-Warning

EXCEPTION - %lu - Unable to activate link station because port outbound link-activation limit reached [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-4-CS_LOG_37

4-Warning

EXCEPTION - %lu - Unable to activate dynamic link station because port total link-activation limit reached [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-4-CS_LOG_38

4-Warning

EXCEPTION - %lu - Unable to activate dynamic link station because port outbound link-activation limit reached [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-6-CS_LOG_39

6-Information

INFO - %lu - Link station to host started [chars]

A non-APPN link station to an upstream host has been\n\ successfully started.

snasw

"None"

SNASW-6-CS_LOG_40

6-Information

INFO - %lu - Link station to DSPU started [chars]

A non-APPN link station to a downstream PU has been\n\ successfully started.

snasw

"None"

SNASW-6-CS_LOG_41

6-Information

INFO - %lu - Link station to host stopped [chars]

A non-APPN link station to an upstream host has been\n\ successfully stopped.

snasw

"None"

SNASW-6-CS_LOG_42

6-Information

INFO - %lu - Link station to DSPU stopped [chars]

A non-APPN link station to a downstream PU has been\n\ successfully stopped.

snasw

"None"

SNASW-4-CS_LOG_43

4-Warning

EXCEPTION - %lu - Unable to find requested link [chars]

A locally initiated dependent session activation request\n\ required SNA Switch to automatically activate a link to a\n\ specified PU name but SNA Switch was unable to identify the\n\ a link to the PU. This problem indicates an inconsistent local\n\ configuration which is transient and is caused by a recent\n\ modification.\n\ The session activation request will fail with the specified\n\ sense code.

snasw

"Check the consistency of the local configuration link\n\ definitions can be viewed using show snasw link."

SNASW-6-CS_LOG_44

6-Information

INFO - %lu - SNA Switch link started [chars]

An SNA Switch link has been successfully started.

snasw

"None"

SNASW-3-CS_LOG_51

3-Error

PROBLEM - %lu - Intra-node session support ended abnormally [chars]

Intra-node session support ended abnormally. This should only\n\ occur because of a shortage of available storage.\n\ Any active intranode sessions will fail and no more intra-node\n\ sessions will be activatable.

snasw

-

SNASW-4-CS_LOG_52

4-Warning

EXCEPTION - %lu - Unable to find requested connection network [chars]

-

snasw

"Check the consistency of the network topology."

SNASW-3-CS_LOG_54

3-Error

PROBLEM - %lu - Insufficient storage to generate link Alert [chars]

Insufficient storage to generate link Alert.\n\ Alert will not be sent.

snasw

-

SNASW-6-CS_LOG_55

6-Information

INFO - %lu - HPR-capable SNA Switch link started [chars]

An SNA Switch link has been successfully started on a node\n\ that supports HPR.

snasw

"None"

SNASW-6-CS_LOG_56

6-Information

INFO - %lu - SNA Switch link stopped [chars]

An SNA Switch link has been successfully stopped.

snasw

"None"

SNASW-6-CS_LOG_57

6-Information

INFO - %lu - DLC started [chars]

A DLC has been successfully started.

snasw

"None"

SNASW-6-CS_LOG_58

6-Information

INFO - %lu - DLC stopped [chars]

A DLC has been successfully stopped.

snasw

"None"

SNASW-6-CS_LOG_59

6-Information

INFO - %lu - Port started [chars]

A Port has been successfully started.

snasw

"None"

SNASW-6-CS_LOG_60

6-Information

INFO - %lu - Port stopped [chars]

A Port has been successfully stopped.

snasw

"None"

SNASW-4-CS_LOG_61

4-Warning

EXCEPTION - %lu - Unable to start requested CP-CP sessions with adjacent node [chars]

The specified link is configured to support CP-CP sessions but\n\ these sessions could not be started. This could either be\n\ because the remote node is not configured to support CP-CP\n\ sessions on this link or because both the local and remote\n\ nodes are End Nodes and hence CP-CP sessions are not allowed\n\ to be started.\n\ CP-CP sessions will not be established.

snasw

"Correct the configuration mismatch either by removing CP-CP\n\ sessions support from the local connection definition or by\n\ adding it to the adjacent node's connection definition."

SNASW-3-CS_LOG_62

3-Error

PROBLEM - %lu - Failed to create DLC [chars]

A DLC could not be started either because of insufficient\n\ resources or because the specified DLC type is not supported.\n\ The DLC is inoperative.

snasw

"If the DLC type is supported then either decrease the system\n\ load for example by reducing the number of active sessions\n\ or make more storage available to SNA Switch."

SNASW-3-CS_LOG_63

3-Error

PROBLEM - %lu - Pre-defined TG number does not match that sent by adjacent node [chars]

The specified link station is configured with a pre-defined TG\n\ number but the adjacent node has sent a different non-zero\n\ TG number.\n\ Link activation will fail.

snasw

"Correct mismatched TG number configuration at this node using\n\ snasw link or at adjacent node."

SNASW-3-CS_LOG_64

3-Error

PROBLEM - %lu - Adjacent node sent a TG number that was pre-assigned to another LS [chars]

Adjacent node has attempted to use a TG number for this link\n\ which is already pre-defined on another link station.\n\ Link activation will fail.

snasw

"Correct mismatched TG number configuration at this node using\n\ snasw link or at adjacent node."

SNASW-3-CS_LOG_65

3-Error

PROBLEM - %lu - Adjacent node sent a TG number that was already in use by another LS [chars]

Adjacent node has attempted to use a TG number for this link\n\ which is already in use by another link station. This may\n\ indicate an interoperability problem.\n\ Link activation will fail.

snasw

"Run a trace on the link station or port to get more diagnostic\n\ information on the problem and contact support with the log\n\ and trace."

SNASW-6-CS_LOG_66

6-Information

INFO - %lu - Adjacent node has changed its CP name [chars]

An adjacent node has changed its CP name.

snasw

"None"

SNASW-3-CS_LOG_67

3-Error

PROBLEM - %lu - Insufficient storage to update topology database with link station [chars]

Insufficient storage to update topology database with link\n\ station information.\n\ Topology will be inconsistent which may result in unexpected\n\ session activation failures typically with sense codes\n\ 8014xxxx 0806002B or 08500001.

snasw

-

SNASW-3-CS_LOG_68

3-Error

PROBLEM - %lu - Insufficient storage to update topology database with connection network [chars]

Insufficient storage to update topology database with\n\ connection network information.\n\ Topology will be inconsistent which may result in unexpected\n\ session activation failures typically with sense codes\n\ 8014xxxx 0806002B or 08500001.

snasw

-

SNASW-3-CS_LOG_69

3-Error

PROBLEM - %lu - Insufficient storage to enable intra-node sessions [chars]

Insufficient storage to enable intra-node sessions.\n\ Intra-node session cannot be activated.

snasw

-

SNASW-3-PS_LOG_1

3-Error

PROBLEM - %lu - Attach rejected because requested conversation type not supported by requested transaction program [chars]

Attach rejected because the specified conversation type is not\n\ supported by the specified transaction program. This may be\n\ a mismatch in the capabilities of the originating transaction\n\ program and the destination transaction program or it may\n\ simply be a configuration error.\n\ The Attach will be rejected.

snasw

"Check the conversation type or types supported by the specified\n\ transaction program and check that this matches the\n\ conversation type supported defined for the transaction program.\n\ If they match or the transaction program is not defined there\n\ is a mismatch between the originating and destination transaction\n\ programs."

SNASW-3-PS_LOG_3

3-Error

PROBLEM - %lu - Conversation ended by protocol error [chars]

The session being used by a conversation has been deactivated\n\ because of a protocol error causing the conversation to fail.\n\ The conversation will be terminated either by an APPC\n\ primary_rc of NAP_CONV_FAILURE_NO_RETRY or a CPI-C return_code\n\ of CM_RESOURCE_FAILURE_NO_RETRY.

snasw

"This log gives information on which TPs and conversation have\n\ been affected by a protocol error on a session. Other more\n\ specific problem or exception logs give more information on the\n\ protocol error. Use the Session identifier to correlate this\n\ log with other related logs."

SNASW-3-PS_LOG_4

3-Error

PROBLEM - %lu - Conversation ended by session outage [chars]

The session being used by a conversation has been deactivated\n\ because of a session outage causing the conversation to fail.\n\ The conversation will be terminated either by an APPC\n\ primary_rc of NAP_CONV_FAILURE_RETRY or a CPI-C return_code of\n\ CM_RESOURCE_FAILURE_RETRY.

snasw

"This log gives information on which TPs and conversation have\n\ been affected by a session outage. Other more specific\n\ problem or exception logs give more information on the reason\n\ for the session outage. Use the Session identifier to\n\ correlate this log with other related logs."

SNASW-4-PS_LOG_5

4-Warning

EXCEPTION - %lu - Protocol error detected on conversation [chars]

-

snasw

"Report the protocol error to partner LU support. If additional\n\ diagnostic information is required run a link trace the\n\ session identifier can be used to correlate this log to other\n\ logs which contain the appropriate link station name."

SNASW-4-PS_LOG_7

4-Warning

EXCEPTION - %lu - Error data received from partner LU. [chars]

The partner TP issued a SEND_ERROR or DEALLOCATE verb\n\ specifying error data.\n\ an error state was generated by the partner TP.\n\ The specified TP will experience a problem. Subsequent\n\ recovery or termination of the conversation will be determined\n\ by the applications.

snasw

"Check that both the local TP and the partner TP exist are\n\ correctly named and are working properly."

SNASW-4-PS_LOG_8

4-Warning

EXCEPTION - %lu - Error data sent to partner LU. [chars]

The local TP issued a SEND_ERROR or DEALLOCATE verb specifying\n\ error data.\n\ The specified TP will experience a problem. Subsequent\n\ recovery or termination of the conversation will be determined\n\ by the applications.

snasw

"Check that both the local TP and the partner TP exist are\n\ correctly named and are working properly."

SNASW-6-PS_LOG_9

6-Information

INFO - %lu - Processed APING from partner LU. [chars]

An APING from the partner LU has been processed successfully.

snasw

"None"

SNASW-3-PS_LOG_10

3-Error

PROBLEM - %lu - Attach rejected because requested conversation duplex type not supported by requested transaction program [chars]

Attach rejected because the specified conversation duplex type\n\ is not supported by the specified transaction program. This\n\ may be a mismatch in the capabilities of the originating\n\ transaction program and the destination transaction program or\n\ it may simply be a configuration error.\n\ Possible sense codes are as follows.\n\ 10086034 Half-duplex Attach not supported by TP\n\ 08640003 Full-duplex Attach not supported by TP\n\ The Attach will be rejected.

snasw

"Check the conversation duplex type or types supported by the\n\ specified transaction program and check that this matches the\n\ conversation type supported defined for the transaction program.\n\ If they match or the transaction program is not defined there\n\ is a mismatch between the originating and destination transaction\n\ programs."

SNASW-4-PS_LOG_11

4-Warning

EXCEPTION - %lu - Entry could not be added to signed-on-to list sending PV sign-on Attach. [chars]

The local LU failed to add an entry into the signed-on-to list\n\ when sending a PV sign-on Attach FMH-5 due to resource\n\msgdef_recommended_action Either decrease the system load

-

-

SNASW-4-PS_LOG_12

4-Warning

EXCEPTION - %lu - Unable to process Sign-Off verb due to resource shortage. [chars]

The local LU was unable to process a Sign-Off verb issued by a\n\ local TP due to resorce shortage.\n\ The Sign-Off request will fail and any entries in the\n\ signed-on-to and sign-on-from lists will remain valid.

snasw

-

SNASW-4-PS_LOG_13

4-Warning

EXCEPTION - %lu - SNA Switch detected a mapped conversation protocol error on an APPC mapped conversation [chars]

SNA Switch detected a mapped conversation protocol error on an\n\ APPC mapped conversation.\n\ The conversation will be terminated either by an APPC\n\ primary_rc of NAP_CONV_FAILURE_NO_RETRY or a CPI-C return_code\n\ of CM_RESOURCE_FAILURE_NO_RETRY. The partner TP will fail the\n\ conversation with an APPC primary_rc of NAP_DEALLOCATE_ABEND or\n\ a CPI-C return_code of CM_DEALLOCATE_ABEND. The session will\n\ not be deactivated.

snasw

"Report the protocol error to partner LU support. If additional\n\ diagnostic information is required run a link trace the\n\ session identifier can be used to correlate this log to other\n\ logs which contain the appropriate link station name."

SNASW-4-PS_LOG_14

4-Warning

EXCEPTION - %lu - SNA Switch detected a mapped conversation protocol error on an APPC mapped conversation [chars]

SNA Switch received an error data GDS variable on an APPC mapped\n\ conversation.\n\ The conversation will be terminated either by an APPC\n\ primary_rc of NAP_CONV_FAILURE_NO_RETRY or a CPI-C return_code\n\ of CM_RESOURCE_FAILURE_NO_RETRY. The partner TP will fail the\n\ conversation with an APPC primary_rc of NAP_DEALLOCATE_ABEND or\n\ a CPI-C return_code of CM_DEALLOCATE_ABEND. The session will\n\ not be deactivated.

snasw

"Report the protocol error to partner LU support. If additional\n\ diagnostic information is required run a link trace the\n\ session identifier can be used to correlate this log to other\n\ logs which contain the appropriate link station name."

SNASW-4-PS_LOG_15

4-Warning

EXCEPTION - %lu - An LU received an aping with data size greater than the maximum allowed [chars]

An LU received an aping with data length greater than the\n\ maximum allowed.\n\ The conversation will be terminated with primary_rc of\n\ DEALLOC_ABEND.

snasw

"Report the error. SNA Switch LUs should not be apinged with a\n\ data size greater than the defined maximum."

SNASW-4-HS_LOG_0

4-Warning

EXCEPTION - %lu - CRV exchange failed [chars]

CRV exchange failed. This indicates the cryptography keys\n\ configured at this LU and the partner LU are inconsistent.\n\ Session will be deactivated with the specified sense code\n\ 08350001.

snasw

-

SNASW-4-HS_LOG_1

4-Warning

EXCEPTION - %lu - LU6.2 session state error [chars]

LU6.2 session state error. This may indicate an\n\ interoperability problem. Sense codes are as follows.\n\ 20020000 - chaining sequence error\n\ 20030000 - bracket state error\n\ 20040000 - received normal flow request when half-duplex\n\ flip-flop state not receive\n\ 200A0000 - immediate request mode violated by partner LU\n\ 200B0000 - queued response indicator invalid\n\ 200E0000 - unexpected SIGNAL response\n\ 200F0000 - received unexpected response or received EXPD RU\n\ before previous EXPD RU has been acknowledged\n\ 20120000 - unexpected sense code on negative response\n\ 40040000 - received RQE BB CEB chain from contention loser\n\ 40110000 - RU category of response doesn't match request\n\ 40120000 - request code of response doesn't match request\n\ 40210000 - QRI setting on response doesn't match request\n\ The session will be deactivated with the specified sense code.

snasw

-

SNASW-4-HS_LOG_3

4-Warning

EXCEPTION - %lu - MU format errors [chars]

LU6.2 session format error. This may indicate an\n\ interoperability problem. Sense codes are as follows.\n\ 080F6051 - security error FMH12 error\n\msgdef_recommended_action Use information on the session deactivated problem log

-

-

SNASW-4-HS_LOG_4

4-Warning

EXCEPTION - %lu - LU6.2 response correlation error [chars]

LU6.2 response correlation error. This may indicate an\n\ interoperability problem. Sense codes are as follows.\n\ 200E0000 - uncorrelated positive response or\n\ uncorrelated RTR response\n\ Session will be deactivated with the specified sense code.

snasw

-

SNASW-4-HS_LOG_5

4-Warning

EXCEPTION - %lu - LU6.2 session ended abnormally - insufficient storage [chars]

LU6.2 session ended abnormally because of insufficient storage.\n\ Session will be deactivated with the specified sense code.

snasw

-

SNASW-4-HS_LOG_6

4-Warning

EXCEPTION - %lu - Protocol error during CRV exchange [chars]

Protocol error during CRV exchange. This indicates a possible\n\ interoperability problem. Sense codes are as follows.\n\ 20090000 - CRV request received from secondary LU or\n\ CRV response received from primary LU or\n\ CRV not received when expected\n\ 10020000 - CRV RU too short\n\ 400F0000 - CRV with FI not set\n\ 400B0000 - CRV chain indicators not set to BC EC\n\ 40140000 - CRV not RQD1\n\ 40110000 - CRV not expedited\n\ 40150000 - CRV with QRI not set\n\ 40080000 - CRV with PI set\n\ 400C0000 - CRV request with BBI EBI or CEBI set\n\ 400D0000 - CRV request with CDI set\n\ 40100000 - CRV request with CSI set to CODE1\n\ 40160000 - CRV request with EDI set\n\ 40170000 - CRV request with PDI set\n\ 40130000 - CRV response RTI and SDI inconsistent\n\ Session will be deactivated with specified sense code.

snasw

-

SNASW-4-HS_LOG_7

4-Warning

EXCEPTION - %lu - SIGNAL RU received on full-duplex conversation [chars]

An incoming SIGNAL RU has been received on a full-duplex\n\ conversation.\n\ The session will be deactivated with the specified sense code.\n\ 10030004

snasw

"Contact support with details of the problem."

SNASW-3-HS_LOG_8

3-Error

PROBLEM - %lu - EXPD RU received while previous expedited data remains to be processed [chars]

An EXPD RU has been received while previous expedited data\n\ remains to be processed.\n\ The session will be deactivated with the specified sense code.\n\ 200F0000

snasw

"Contact support with details of the problem."

SNASW-4-HS_LOG_9

4-Warning

EXCEPTION - %lu - Insufficient storage to initialise half session [chars]

Insufficient storage to initialise the half session.\n\ The half session will fail to activate with the specified sense\n\ code.

snasw

-

SNASW-4-TC_LOG_0

4-Warning

EXCEPTION - %lu - Session pacing error [chars]

Session pacing error. This may indicate an interoperability\n\ problem. Sense codes are as follows.\n\ 20110000 - sender has overrun pacing window or\n\ PI not set on first RU of window\n\ 20110001 - unexpected IPM\n\ 20110002 - PI set on other than first RU in window\n\ 20110003 - invalid pacing response\n\ 10010003 - invalid IPM format\n\ The session will be deactivated with the specified sense code.

snasw

-

SNASW-4-TC_LOG_1

4-Warning

EXCEPTION - %lu - Session segmentation error [chars]

Session segmentation error. This may indicate an\n\ interoperability problem. Sense codes are as follows.\n\ 80070000 - segmenting error\n\ 80070001 - segmentation not supported on this link\n\ The session will be deactivated with the specified sense code.

snasw

-

SNASW-4-TC_LOG_2

4-Warning

EXCEPTION - %lu - RU length error [chars]

RU length error. This may indicate an\n\ interoperability problem. Sense codes are as follows.\n\ 10020000 - RU length error\n\ The session will be deactivated with the specified sense code.

snasw

-

SNASW-4-PC_LOG_0

4-Warning

EXCEPTION - %lu - Unable to route intra-node session data [chars]

Unable to route intra-node session data. This usually\n\ indicates a race condition when an intra-node session is\n\ deactivating.\n\ None.

snasw

"None."

SNASW-4-PC_LOG_4

4-Warning

EXCEPTION - %lu - Insufficient storage to generate Alert [chars]

Insufficient storage to generate Alert to report invalid\n\ received data.\n\ Alert is not generated.

snasw

-

SNASW-4-PC_LOG_5

4-Warning

EXCEPTION - %lu - Unable to route inter-node session data [chars]

Unable to route inter-node session data. This usually\n\ indicates a race condition when an inter-node session is\n\ deactivating.\n\ None.

snasw

"None."

SNASW-4-PC_LOG_9

4-Warning

EXCEPTION - %lu - Unable to forward an HPR NLP - unknown ANR label [chars]

-

snasw

"Use show snasw link to look for an active HPR-capable link with the\n\ specified ANR label. If there is one then the problem has\n\ been caused by a storage shortage. Either decrease the system\n\ load for example by reducing the number of active sessions\n\ or make more storage available to SNA Switch."

SNASW-3-PC_LOG_10

3-Error

PROBLEM - %lu - Insufficient storage to start link inactivity timer [chars]

Insufficient storage to start link-inactivity timer.\n\ Limited resource link will not be automatically deactivated.

snasw

-

SNASW-3-PC_LOG_11

3-Error

PROBLEM - %lu - Unable to forward an HPR NLP - insufficient storage [chars]

Insufficient storage to forward HPR Network Layer Packet.\n\ NLP will be discarded. If this error occurs frequently it may\n\ cause RTP connections to path-switch or fail altogether.

snasw

-

SNASW-3-PC_LOG_12

3-Error

PROBLEM - %lu - Insufficient storage to register ANR label [chars]

Insufficient storage to register ANR label.\n\ HPR traffic using this ANR label will not be routed correctly\n\ which may cause RTP connections to path-switch or fail\n\ altogether.

snasw

-

SNASW-4-PC_LOG_14

4-Warning

EXCEPTION - %lu - Received a frame with a badly formed transmission header or a frame that is too small to be a valid SNA frame [chars]

Received a frame with a badly formed transmission header or a\n\ frame that is too small to be a valid SNA frame.\n\ The invalid frame will be discarded. An alert is generated.

snasw

"None."

SNASW-4-PC_LOG_15

4-Warning

EXCEPTION - %lu - Unable to correlate DLC credit for MLTG link [chars]

Unable to correlate DLC credit for MLTG link.\n\ Probably none. This exception will occur during a window\n\ condition in normal link deactivation.

snasw

"If several instances of this log appear and also poor RTP\n\ connection performance is observed investigate further by\n\ querying link stations which are members of MLTGs.\n\ Unexpectedly low quantities of data sent over a link may\n\ indicate problems with DLC credit. Contact support with\n\ details of the problem including trace of signals sent to and\n\ from the DLCs underlying the affected links."

SNASW-4-PC_LOG_16

4-Warning

EXCEPTION - %lu - Link failure because too many outgoing packets are queued for transmission [chars]

A remote node is not processing information fast enough and is\n\ causing large queues to form on this node.\n\ Link failure.

snasw

"Check the error logs on the remote node that this link is\n\ connected to."

SNASW-4-PC_LOG_17

4-Warning

EXCEPTION - %lu - Link failure because too many outgoing packets are queued for transmission [chars]

A remote node is not processing information fast enough and is\n\ causing large queues to form on this node.\n\ Link failure.

snasw

"Check the error logs on the remote nodes that this MLTG is\n\ connected to."

SNASW-6-NOF_LOG_2

6-Information

INFO - %lu - Node started [chars]

Node has been successfully started.

snasw

"None"

SNASW-3-NOF_LOG_3

3-Error

PROBLEM - %lu - Insufficient storage to start SNA Switch [chars]

Insufficient storage to start SNA Switch.\n\ SNA Switch was not started.

snasw

"Make more storage available to SNA Switch."

SNASW-6-NOF_LOG_4

6-Information

INFO - %lu - Node stopped [chars]

Node has been successfully stopped.

snasw

"None"

SNASW-3-NOF_LOG_7

3-Error

PROBLEM - %lu - Failed to dynamically load TP [chars]

Failed to dynamically load an APPC transaction program or CPI-C\n\ application.\n\ The received Attach will be failed with the specified sense\n\ code.

snasw

"Collect trace and report the problem to support."

SNASW-3-NOF_LOG_10

3-Error

PROBLEM - %lu - Insufficient storage to process ACTLU [chars]

Insufficient storage to process received ACTLU\n\ LU-SSCP session will not be started an ACTLU -ve response with\n\ the specified sense code is sent.

snasw

-

SNASW-3-NOF_LOG_11

3-Error

PROBLEM - %lu - ACTLU received for LU which is not defined locally and implicit LU definition is not supported [chars]

ACTLU received for LU which is not defined locally and\n\ implicit LU definition is not supported. This typically\n\ indicates a mismatch between this node and the host\n\ configuration.\n\ LU-SSCP session is not activated ACTLU is rejected with the\n\ specified sense code.

snasw

"Remove the LU from the host configuration."

SNASW-4-NOF_LOG_15

4-Warning

EXCEPTION - %lu - An LU-SSCP session activation attempt failed because the SSCP was not suitable [chars]

An ACTLU was received for an LU from the wrong SSCP.\n\ The ACTLU is rejected with sense code 084B0000 i.e. the LU\n\ activation attempt fails.

snasw

-

SNASW-3-SM_LOG_0

3-Error

PROBLEM - %lu - Insufficient storage to define LU type 6.2 [chars]

Insufficient storage to define a new LU type 6.2.

snasw

-

SNASW-3-SM_LOG_1

3-Error

PROBLEM - %lu - Fatal error detected on LU6.2 session [chars]

Fatal error detected on LU6.2 session.\n\ Session will be deactivated with specified sense code.

snasw

-

SNASW-3-SM_LOG_2

3-Error

PROBLEM - %lu - BIND or +RSPBIND specifies duplex support which is different from that for existing sessions [chars]

-

snasw

"Contact support with details of the problem."

SNASW-3-SM_LOG_5

3-Error

PROBLEM - %lu - Insufficient storage to activate LU6.2 session [chars]

Insufficient storage to activate LU6.2 session.\n\ Session activation will fail with the specified sense code.

snasw

-

SNASW-4-SM_LOG_6

4-Warning

EXCEPTION - %lu - Abnormal UNBIND request received [chars]

Abnormal UNBIND request received. This may indicate a\n\ configuration error or a protocol error.\n\ The session will fail with the specified sense code.

snasw

"If the sense code indicates a configuration error check for\n\ inconsistencies between the configuration at the local LU and\n\ the configuration at the partner LU. If the configuration is\n\ consistent and the problem persists contact support with\n\ details of the problem."

SNASW-3-SM_LOG_10

3-Error

PROBLEM - %lu - Format error in received LU6.2 BIND request [chars]

Format error in received LU6.2 BIND request. Sense codes are\n\ as follows.\n\ 0835xxxx - parameter error at offset xxxx in BIND RU\n\ 088C6000 - FQPCID not included in extended BIND\n\ 083B0000 - invalid FQPCID format\n\ Session activation will fail with specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-SM_LOG_11

3-Error

PROBLEM - %lu - Format error in received LU6.2 BIND response [chars]

Format error in received LU6.2 BIND response. Sense codes are\n\ as follows.\n\ 0835xxxx - parameter error at offset xxxx in BIND RU\n\ Session activation will fail with specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-SM_LOG_12

3-Error

PROBLEM - %lu - LU-mode session limit exceeded [chars]

LU-mode session limit exceeded. This problem normally should\n\ not occur since the session limits are negotiated with a CNOS\n\ exchange prior to sessions being activated. However this\n\ log can also be caused by a normal race condition when the\n\ session limits are reset or when this node has been restarted\n\ after having previously had sessions with this partner LU.\n\ Session activation will fail with specified sense code.

snasw

"If problem persists check the session limits and active\n\ session counts on the specified local LU partner LU."

SNASW-4-SM_LOG_13

4-Warning

EXCEPTION - %lu - BIND race with single-session partner LU - partner LU has lost race [chars]

BIND race with single-session partner LU. This is a normal\n\ network race condition. The race is resolved in favour of the\n\ LU with the higher name. In this case the partner LU lost the\n\ race.\n\ Session activation will fail with specified sense code.

snasw

"None."

SNASW-3-SM_LOG_14

3-Error

PROBLEM - %lu - Detected consistency errors in received BIND request [chars]

Detected consistency errors in received BIND request. This\n\ may indicate an interoperability problem. Sense codes are as\n\ follows.\n\ 0835xxxx - parameter error at offset xxxx in BIND RU\n\ 080F6051 - security error\n\ Session activation will fail with specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-SM_LOG_15

3-Error

PROBLEM - %lu - Detected consistency errors in received BIND response [chars]

Detected consistency errors in received BIND response. This\n\ may indicate an interoperability problem. Sense codes are as\n\ follows\n\ 0835xxxx - parameter error at offset xxxx in BIND RU\n\ 080F6051 - security error\n\ Session will be deactivated with specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-SM_LOG_16

3-Error

PROBLEM - %lu - Format error in received UNBIND request [chars]

Format error in received UNBIND request. This may indicate an\n\ interoperability problem. Sense codes are as follows.\n\ 0835xxxx - parameter error at offset xxxx in UNBIND RU\n\ 0895xxyy - format error in control vector where xx is key of\n\ control vector and yy is offset into control\n\ vector of byte in error\n\ 10020000 - RU length error\n\ None session will still be deactivated.

snasw

"Contact support with details of the problem."

SNASW-4-SM_LOG_18

4-Warning

EXCEPTION - %lu - Unable to correlate received BIND response [chars]

-

snasw

"None."

SNASW-4-SM_LOG_20

4-Warning

EXCEPTION - %lu - Unable to correlate received INIT-SELF response or NOTIFY request [chars]

-

snasw

"None."

SNASW-4-SM_LOG_21

4-Warning

EXCEPTION - %lu - Unable to correlate received UNBIND request [chars]

-

snasw

"None."

SNASW-4-SM_LOG_30

4-Warning

EXCEPTION - %lu - Received ACTLU when LU already active [chars]

ACTLU received when LU already active.\n\ ACTLU will be rejected with specified sense code.

snasw

"Run a trace on the link station corresponding to the specified\n\ PU name. Contact host support with details of the problem."

SNASW-3-SM_LOG_31

3-Error

PROBLEM - %lu - Insufficient storage to activate LU-SSCP session [chars]

Insufficient storage to activate LU-SSCP session.\n\ ACTLU will be rejected with specified sense code.

snasw

-

SNASW-4-SM_LOG_32

4-Warning

EXCEPTION - %lu - Unable to activate a new session since it would exceed the LU-mode session limit [chars]

Unable to activate a new session since it would exceed the\n\ LU-mode session limits. This problem is a normal race\n\ condition and so should occur infrequently.\n\ Session activation will fail with specified sense code which\n\ may cause ALLOCATE MC_ALLOCATE or CMALLC requests to fail.

snasw

"None."

SNASW-3-SM_LOG_33

3-Error

PROBLEM - %lu - Insufficient storage to reassemble received BIND response [chars]

Insufficient storage to reassemble received BIND response.\n\ Session will be deactivated with the specified sense code.

snasw

-

SNASW-3-SM_LOG_34

3-Error

PROBLEM - %lu - Badly formed partner LU name in received BIND request [chars]

Partner LU name on received BIND request is badly formed.\n\ Session activation will fail with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-SM_LOG_35

3-Error

PROBLEM - %lu - Unrecognized mode name in received BIND request [chars]

Mode name on received BIND request is unrecognized.\n\ Session activation will fail with the specified sense code.

snasw

"Modify the partner LU configuration so it does not\n\ attempt to use the unrecognized mode."

SNASW-3-SM_LOG_36

3-Error

PROBLEM - %lu - Unable to activate session to single session partner LU because there is an active session on another mode [chars]

Unable to activate session to single session partner LU\n\ because there is already an active session on another mode.\n\ This usually indicates contention between two or more APPC\n\ transaction programs or CPI-C applications for the same\n\ dependent LU6.2.\n\ Session activation will fail with specified sense code which\n\ may cause ALLOCATE MC_ALLOCATE or CMALLC requests to fail.

snasw

"Collect trace and report the problem to support."

SNASW-6-SM_LOG_37

6-Information

INFO - %lu - LU6.2 session activated [chars]

An LU6.2 session has been activated.

snasw

"None"

SNASW-6-SM_LOG_38

6-Information

INFO - %lu - LU6.2 session deactivated [chars]

An LU6.2 session has been deactivated.

snasw

"None"

SNASW-4-SM_LOG_39

4-Warning

EXCEPTION - %lu - An LU-SSCP session activation attempt failed because the SSCP was not suitable [chars]

An ACTLU was received for an LU from the wrong SSCP.\n\ The ACTLU is rejected with sense code 084B0000 i.e. the LU\n\ activation attempt fails.

snasw

-

SNASW-4-SM_LOG_40

4-Warning

EXCEPTION - %lu - LU-mode session limit exceeded - BIND race [chars]

LU-mode session limit exceeded - BIND race. This is normal\n\ race condition caused by both the local LU and partner LU\n\ attempting to activate the last session on the mode\n\ simultaneously. The race will be resolved in favour of the\n\ node with the higher name. In this case the partner LU has\n\ lost the race.\n\ Session activation will fail with specified sense code.

snasw

"None."

SNASW-3-SM_LOG_41

3-Error

PROBLEM - %lu - FQPCID collision on received BIND request [chars]

FQPCID collision. The FQPCID specified on a received BIND\n\ request matches the FQPCID being used for an existing active\n\ session. This can be caused by a collision in the hashing\n\ algorithm used to generate an FQPCID or it may indicate a\n\ problem in the node generating the FQPCID.\n\ Session activation will fail with specified sense code.

snasw

"If problem is persistent or occurs often contact support with\n\ details of the problem."

SNASW-3-SM_LOG_42

3-Error

PROBLEM - %lu - Session identifier collision on received BIND request [chars]

Session identifier collision. The session identifier specified\n\ on a received BIND request matches the session identifier being\n\ an existing active session.\n\ Session activation will fail with specified sense code.

snasw

"If problem is persistent or occurs often contact support with\n\ details of the problem."

SNASW-6-SM_LOG_43

6-Information

INFO - %lu - An LU-SSCP session has been activated for LU type 6.2 [chars]

An LU-SSCP session has been activated.

snasw

"None"

SNASW-6-SM_LOG_44

6-Information

INFO - %lu - An LU-SSCP session has been deactivated for LU type 6.2 [chars]

An LU-SSCP session has been deactivated.

snasw

"None"

SNASW-3-SM_LOG_45

3-Error

PROBLEM - %lu - LU-LU verification protocol mismatch. [chars]

LU-LU verification protocol mismatch. The partner LU has\n\ requested that the basic protocol is used when the local LU\n\ runs only the enhanced protocol with the partner LU. The local\n\ LU may be configured to run only the enhanced protocol with the\n\ partner LU or it may be configured to run either protocol with\n\ the partner LU and has determined that the partner LU can run\n\ the enhanced protocol. This is either\n\ i a mismatch in configuration\n\msgdef_recommended_action Check the identity of the partner LU. If the problem is\n\

-

-

SNASW-3-SM_LOG_46

3-Error

PROBLEM - %lu - LU-LU verification failed. [chars]

LU-LU verification failed. The partner LU has sent an incorrect\n\ response to a challenge sent by a local LU. This is either a\n\ mismatch in configuration or a security attack.\n\ Session activation will fail.

snasw

-

SNASW-3-SM_LOG_47

3-Error

PROBLEM - %lu - LU-LU verification protocol failed. [chars]

Duplicate random data received. A list is kept of all random\n\ data sent as challenges by the local LU. Receiving duplicate\n\ random data from a partner LU should be a rare event and is\n\ evidence of a security attack.\n\ Session activation will fail.

snasw

-

SNASW-3-SM_LOG_48

3-Error

PROBLEM - %lu - BIND-RSP request received in response to a BIND request [chars]

-

snasw

"If the sense code indicates a configuration error check for\n\ inconsistencies between the configuration at the local LU and\n\ the configuration at the partner LU. If the configuration is\n\ consistent and the problem persists contact support with\n\ details of the problem."

SNASW-4-SM_LOG_49

4-Warning

EXCEPTION - %lu - UNBIND request received in response to a BIND request [chars]

UNBIND request received in response to a BIND request. This may\n\ indicate a configuration error or a protocol error.\n\\n\ Common sense codes which typically indicate a configuration\n\ error or a normal race condition include\n\ 0805xxxx - the session could not be activated as session\n\ activation limits have been reached\n\ 08060014 - the partner LU is not known\n\ 0806xxxx - the BIND specified a resource which is not known\n\ 080Fxxxx - security authorization failed\n\ 0821xxxx - the BIND supplied an invalid session parameter\n\ 0835xxxx - parameter error in BIND RU at offset xxxx\n\\n\ Other sense codes include\n\ 0812xxxx - session activation failed due to resource shortage\n\ at the remote node\n\ 083Bxxxx - invalid PCID in BIND RU\n\ 0852xxxx - duplicate session activation request\n\ 0861xxxx - invalid COS name in BIND RU\n\ 088Cxxxx - control vector or subfield missing from BIND RU\n\ 0895xxxx - BIND RU contained a control vector that was in\n\ error\n\ 0896xxxx - BIND RU contained a control vector that was too\n\ long\n\ Session activation will fail with the specified sense code.

snasw

"If the sense code indicates a configuration error check for\n\ inconsistencies between the configuration at the local LU and\n\ the configuration at the partner LU. If the configuration is\n\ consistent and the problem persists contact support with\n\ details of the problem."

SNASW-3-ASM_LOG_0

3-Error

PROBLEM - %lu - Received BIND request directed at this node with unrecognized secondary LU name [chars]

-

snasw

"Correct primary LU configuration."

SNASW-3-ASM_LOG_2

3-Error

PROBLEM - %lu - Insufficient storage to generate an Alert [chars]

Insufficient storage to generate Alert to report a BIND\n\ segmentation or pacing error.\n\ The Alert will not be sent.

snasw

-

SNASW-3-ASM_LOG_3

3-Error

PROBLEM - %lu - Insufficient storage to process received BIND request [chars]

Insufficient storage to process received BIND request.\n\ The BIND will be rejected with the specified sense code.

snasw

-

SNASW-3-ASM_LOG_4

3-Error

PROBLEM - %lu - ACTPU ACTLU DACTPU or DACTLU received on link on which dependent LUs are not supported [chars]

ACTPU ACTLU DACTPU or DACTLU received over a link on which\n\ dependent LUs are not supported. This may indicate an\n\ interoperability problem.\n\ Request will be rejected with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_5

3-Error

PROBLEM - %lu - Branch Network Node received BIND request with badly formed RSCV [chars]

A Branch Network Node has received a BIND request with a badly\n\ formed RSCV. This may indicate an interoperability problem.\n\ Session activation will fail.

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_6

3-Error

PROBLEM - %lu - Badly-formed BIND request rejected by SNA Switch [chars]

SNA Switch received and rejected a badly-formed BIND request.\n\ This may indicate an interoperability problem.\n\ Session activation will fail.

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_7

3-Error

PROBLEM - %lu - BIND received with the next hop in the RSCV set to the local node again [chars]

SNA Switch received a BIND request with a badly formatted\n\ RSCV. The CP name for the next hop in the RSCV is this local\n\ node again. Sesion activation will fail.

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_11

3-Error

PROBLEM - %lu - Received BIND request with badly formed secondary LU name [chars]

Received BIND request with badly formed secondary LU name.\n\ This may indicate an interoperability problem.\n\ Session activation will fail with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_12

3-Error

PROBLEM - %lu - Received BIND request where network ID of secondary LU does not match local network ID [chars]

Received BIND request where network identifier of secondary LU\n\ does not match local network identifier.\n\ Session activation will fail with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-4-ASM_LOG_15

4-Warning

EXCEPTION - %lu - Insufficient storage to deactivate link [chars]

Insufficient storage to deactivate a link.\n\ The link will not be deactivated

snasw

-

SNASW-4-ASM_LOG_18

4-Warning

EXCEPTION - %lu - Unable to correlate received BIND response [chars]

Unable to correlate received BIND response. This is a normal\n\ race condition caused by a BIND being followed immediately\n\ by an UNBIND for the same session.\n\ BIND response is discarded.

snasw

"None."

SNASW-3-ASM_LOG_19

3-Error

PROBLEM - %lu - Received BIND using LFSID that is already in use [chars]

-

snasw

"If problem is persistent or occurs frequently contact\n\ support with details of the problem."

SNASW-3-ASM_LOG_22

3-Error

PROBLEM - %lu - Session control request received with invalid LFSID [chars]

-

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_24

3-Error

PROBLEM - %lu - Failed to initialize address space instance [chars]

Insufficient storage to create a local form session identifier\n\ routing table for a link station.\n\ Link activation will fail.

snasw

-

SNASW-4-ASM_LOG_25

4-Warning

EXCEPTION - %lu - Unable to extend local form session identifier routing table [chars]

Unable to extend local form session identifier routing table.\n\ Session activation will fail with the specified sense code.

snasw

-

SNASW-4-ASM_LOG_26

4-Warning

EXCEPTION - %lu - Independent LU session deactivated because LU deleted [chars]

An independent LU-LU session has been deactivated because the\n\ local LU has been deleted.\n\ None.

snasw

"None."

SNASW-3-ASM_LOG_27

3-Error

PROBLEM - %lu - Detected fatal BIND or UNBIND protocol error [chars]

-

snasw

"Contact support with details of the problem."

SNASW-3-ASM_LOG_28

3-Error

PROBLEM - %lu - Received BIND IPM on link where adaptive BIND pacing not supported [chars]

Received BIND IPM on link where adaptive BIND pacing is not\n\ supported. This may indicate an interoperability problem.\n\ BIND IPM will be discarded.

snasw

"Contact support with details of the problem."

SNASW-4-ASM_LOG_29

4-Warning

EXCEPTION - %lu - Dependent LU session deactivated because LU deleted [chars]

A dependent LU-LU session has been deactivated because the\n\ LU has been deleted.\n\ None.

snasw

"None."

SNASW-4-MS_LOG_3

4-Warning

EXCEPTION - %lu - Insufficient storage to deliver MDS_MU to a registered application [chars]

Insufficient storage to deliver MDS_MU to a registered\n\ application.\n\ The MU will be returned to the sender indicating a resource\n\ shortage error.

snasw

-

SNASW-4-MS_LOG_5

4-Warning

EXCEPTION - %lu - Memory shortage in processing signal [chars]

The system was unable to allocate memory to process an incoming\n\ TRANSFER_MS_DATA or SEND_MDS_MU or register signal.\n\ The signal will be returned to the sender noting the resource\n\ shortage error.

snasw

-

SNASW-4-MS_LOG_6

4-Warning

EXCEPTION - %lu - MS unable to add time stamp and/or product set id [chars]

The system was unable to add the product set id or the date\n\ time stamp requested due to either memory shortage or the\n\ addition causing an NMVT to exceed maximum size.\n\ Additions will not be made to the signal.

snasw

-

SNASW-6-MS_LOG_7

6-Information

INFO - %lu - Alert data logged [chars]

TRANSFER_MS_DATA/SEND_MDS_MU data has arrived.

snasw

"None"

SNASW-4-MS_LOG_8

4-Warning

EXCEPTION - %lu - Memory shortage preventing data log [chars]

The system was unable to allocate memory and was thus unable\n\ to log data supplied by the user.\n\ The data will not be logged.

snasw

-

SNASW-4-MS_LOG_9

4-Warning

EXCEPTION - %lu - Unrecognized signal received from application [chars]

A signal was received which was unrecognized and could not\n\ be returned to the sender.\n\ The signal memory will be freed.

snasw

"Check that issued signals are acceptable according to the\n\ API specification."

SNASW-4-MS_LOG_10

4-Warning

EXCEPTION - %lu - Alert/Resolution received and cannot be sent [chars]

Memory failure in trying to allocate space to route a back-\n\ level alert or resolution to the parent MS process.\n\ The alert or resolution will not be sent. It is logged here.

snasw

-

SNASW-4-MS_LOG_12

4-Warning

EXCEPTION - %lu - Memory shortage in verb processing [chars]

The system was unable to allocate control block space to\n\ process an incoming verb.\n\ The verb will not be processed and it will be returned to\n\ the sending application with a primary return code of\n\ NAP_UNEXPECTED_SYSTEM_ERROR.

snasw

-

SNASW-4-MS_LOG_13

4-Warning

EXCEPTION - %lu - Memory shortage in trying to send an alert [chars]

The system was unable to allocate memory needed to send an\n\ alert.\n\ The alert will not be sent however the sense code of the\n\ alert will be logged.

snasw

-

SNASW-4-MS_LOG_14

4-Warning

EXCEPTION - %lu - Memory shortage in MDS_MU processing [chars]

The system was unable to needed memory for processing an\n\ MDS_MU.\n\ The MDS_MU will not be processed. If the MDS_MU originated at\n\ the local node the SEND_MDS_MU verb containing the MDS_MU will\n\ be returned to the sending application noting the error. If the\n\ MDS_MU did not originate from the local node an error message\n\ will be returned to the originating application.

snasw

-

SNASW-4-MS_LOG_15

4-Warning

EXCEPTION - %lu - Correlator clash detected in MDS_MU processing [chars]

A correlation error was detected while processing an MDS_MU.\n\ The MDS_MU will not be processed. If the MDS_MU originated at\n\ the local node the SEND_MDS_MU verb containing the MDS_MU will\n\ be returned to the sending application noting the error. If the\n\ MDS_MU did not originate from the local node an error message\n\ will be returned to the originating application. An error\n\ message may also be sent to other applications if they are\n\ affected by the correlation clash.

snasw

"User should reissue the SEND_MDS_MU but with a correct\n\ correlator value."

SNASW-4-MS_LOG_16

4-Warning

EXCEPTION - %lu - Insufficient storage to pass Alert data to registered Alert handler [chars]

Insufficient storage to pass Alert to registered Alert Handler.\n\ The alert will not be sent however it will be logged.

snasw

-

SNASW-4-MS_LOG_17

4-Warning

EXCEPTION - %lu - Following alert failed to be sent to focal point [chars]

The system received a send failure for an alert stored on the\n\ send alert queue. No held alert function is available to\n\ store the alert until another focal point is established.\n\ alert to the alert handler.\n\ The alert will not be sent however it will be logged.

snasw

"None."

SNASW-4-MS_LOG_18

4-Warning

EXCEPTION - %lu - Error on alert send not correlated with entries on send alert queue [chars]

The system was unable to correlate an error received on an\n\ alert send with the alerts stored in the send alert queue.\n\ The send alert queue is either too small and the original alert\n\ has been deleted or a previous error prevented the alert from\n\ being held on the queue.\n\ The alert will not be sent to the focal point.

snasw

"Investigate whether prior memory shortage caused alert\n\ not to be held on the queue."

SNASW-3-MS_LOG_22

3-Error

PROBLEM - %lu - Error message received reporting invalid format of our MDS_MUs [chars]

MS Capabilities received an error message reporting a format\n\ error on an MDS_MU our node supposedly sent.\n\ The error message will be logged however no further action\n\ can be taken. Ignoring the message may lead to further\n\ unexpected occurrences.

snasw

"Contact support with details of the problem"

SNASW-4-MS_LOG_23

4-Warning

EXCEPTION - %lu - MS Capabilities unable to send request due to memory shortage [chars]

MS Capabilities failed to get space to send a message.\n\ The message will not be sent. If the intended message was\n\ a request for focal point services MS will pursue focal point\n\ services alternatively. If the intended message was to revoke\n\ a previous focal point the message will not be sent. The node\n\ will still appear in the focal point's sphere of control list.

snasw

-

SNASW-4-MS_LOG_24

4-Warning

EXCEPTION - %lu - Error message received at MS Capabilities delivery failure [chars]

MS Capabilities received an error message. This is assumed\n\ to be the result of a send failure.\n\ The error message received will be logged so that send failure\n\ types can be examined. MS capabilities will take appropriate\n\ recovery action if the failed send effects the focal point\n\ table.

snasw

"Contact support with details of the problem."

SNASW-4-MS_LOG_27

4-Warning

EXCEPTION - %lu - Memory Failure in MDS creation sequence [chars]

MDS failed to get needed memory during the creation sequence.\n\ The MDS creation will fail.

snasw

-

SNASW-4-MS_LOG_28

4-Warning

EXCEPTION - %lu - Insufficient storage to process received MS Capabilities information [chars]

Insufficient storage to processed received MS Capabilities\n\ information.\n\ The category for which this failure occurred will be reset.

snasw

-

SNASW-4-MS_LOG_29

4-Warning

EXCEPTION - %lu - Parsing error found in MDS_MU header [chars]

MDS received an MDS_MU that it could not parse correctly.\n\ An alert will be raised. If the MDS_MU originated from a\n\ local application the SEND_MDS_MU will be returned with\n\ the return codes NAP_PARAMETER_CHECK and\n\ NAP_INVALID_MDS_MU_FORMAT.

snasw

"Investigate syntax of MDS_MU sent correct syntax and reissue\n\ the SEND_MDS_MU."

SNASW-4-MS_LOG_31

4-Warning

EXCEPTION - %lu - Insufficient storage to queue Alert/Resolution for error correlation [chars]

Insufficient storage to queue alert or resolution for error\n\ correlation\n\ The alert or resolution will not be queued and thus if an\n\ error message regarding the failure to send this alert or\n\ resolution is received MDS will be unable to correlate it. If\n\ the alert or resolution is sent successfully no further\n\ problems will result.

snasw

-

SNASW-4-MS_LOG_32

4-Warning

EXCEPTION - %lu - MDS unable to get memory to send TP_ENDED [chars]

MDS unable to get buffer to send TP_ENDED for SEND_TP.\n\ TP_ENDED will not be sent.

snasw

-

SNASW-4-MS_LOG_33

4-Warning

EXCEPTION - %lu - MDS unable to get memory for SNASVCMG session list entry [chars]

MDS unable to get memory for a SNASVCMG session control block.\n\ The control block will not be obtained.

snasw

-

SNASW-4-MS_LOG_34

4-Warning

EXCEPTION - %lu - Unexpected what_received in MDS Transaction Program [chars]

An MDS Transaction Program received an unexpected what_received.\n\ The transaction program will re-initialize. The MDS_MU that was\n\ being sent will be returned to the originator if the error\n\ was detected at the originating node or the originator will\n\ be notified of the send failure via an error message.

snasw

"Investigate cause of unexpected what_received."

SNASW-4-MS_LOG_36

4-Warning

EXCEPTION - %lu - Following locally originated MSCAPS message failed to be sent [chars]

The system received a send failure for a local MS capabilities\n\ originated message.\n\ MS capabilities will treat the send failure as a loss of\n\ connectivity to the partner node. If focal point relationships\n\ are affected then MS capabilities will take appropriate\n\ recovery action.

snasw

"Investigate cause of failed send."

SNASW-4-MS_LOG_37

4-Warning

EXCEPTION - %lu - MS unable to allocate space for link control block [chars]

The system was unable to allocate resource to set up a\n\ link control block for a received PU_STATUS message.\n\ The active link will be treated as unknown by MS. Any messages\n\ received over the link will be returned as undeliverable.\n\ Any TRANSFER_MS_DATA or SEND_MDS_MUs received from applications\n\ specifying the link in the PU_STATUS will be returned with\n\ link_name unknown.

snasw

-

SNASW-4-CH_LOG_0

4-Warning

EXCEPTION - %lu - LU type 012 or 3 format error [chars]

LU type 012 or 3 format error. This may indicate an\n\ interoperability problem.\n\ The PIU containing the error is discarded.

snasw

"Contact support with details of the problem"

SNASW-4-CH_LOG_1

4-Warning

EXCEPTION - %lu - LU type 012 or 3 session ended abnormally because of insufficient storage [chars]

LU type 012 or 3 session ended abnormally because of\n\ insufficient storage.\n\ Session will be deactivated with the specified sense code.

snasw

-

SNASW-4-CH_LOG_2

4-Warning

EXCEPTION - %lu - LU type 012 or 3 session ended abnormally while receiving data [chars]

LU type 012 or 3 session ended abnormally while receiving\n\ data.\n\ Session will be deactivated with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-4-CH_LOG_3

4-Warning

EXCEPTION - %lu - LU type 012 or 3 session ended abnormally because of invalid application data [chars]

LU type 012 or 3 session ended abnormally because of\n\ invalid data received from application.\n\ Session will be deactivated with the specified sense code.

snasw

"Contact support with details of the problem."

SNASW-4-CH_LOG_4

4-Warning

EXCEPTION - %lu - Application sent invalid Data message [chars]

LU type 012 or 3 application sent invalid Data message.\n\ Status Acknowledge NACK-2 sent to application.

snasw

"Investigate the error in the application."

SNASW-4-CH_LOG_5

4-Warning

EXCEPTION - %lu - Application sent invalid Status Control message [chars]

LU type 012 or 3 application sent invalid Status Control\n\ message.\n\ Status Control NACK-2 sent to application.

snasw

"Investigate the error in the application."

SNASW-4-CH_LOG_6

4-Warning

EXCEPTION - %lu - Application sent invalid Acknowledgment or Status message [chars]

LU type 012 or 3 application sent invalid Acknowledgment or\n\ Status message.\n\ Status Error sent to application.

snasw

"Investigate the error in the application."

SNASW-4-CH_LOG_8

4-Warning

EXCEPTION - %lu - Insufficient storage to report RTM statistics to Host [chars]

Insufficient storage to report RTM statistics to host.\n\ RTM statistics displayed by host will be inconsistent.

snasw

-

SNASW-4-CH_LOG_9

4-Warning

EXCEPTION - %lu - Insufficient storage to report RTM status to application [chars]

Insufficient storage to report RTM status to application.\n\ RTM statistics reported and displayed by application may be\n\ inconsistent.

snasw

-

SNASW-4-APPN_LOG_0

4-Warning

EXCEPTION - %lu - SNA Switch could not allocate necessary storage [chars]

SNA Switch could not allocate necessary storage.\n\ Some operation may fail. See other logs.

snasw

-

SNASW-3-APPN_LOG_1

3-Error

PROBLEM - %lu - SNA Switch could not allocate necessary storage [chars]

SNA Switch could not allocate necessary storage.\n\ Some operation will fail. See other logs/verbs.

snasw

-

SNASW-4-APPN_LOG_2

4-Warning

EXCEPTION - %lu - SNA Switch cryptography call failed possibly due to missing password [chars]

A call from SNA Switch to perform a cryptographic operation\n\ failed.\n\ Session activation will fail or an active session will end\n\ abnormally with the given sense code or some other action will\n\ fail. More information may appear in subsequent logs.

snasw

"Check following logs for evidence of failed session activation.\n\ If this is evident check MODE LS or INTERNAL PU definitions\n\ for cryptographic support. Check that any passwords necessary\n\ have been defined.\n\ If this problem occurs intermittently or with sessions already\n\ active with the same PLU SLU and mode then make more storage\n\ available to SNA Switch."

SNASW-4-TS_LOG_0

4-Warning

EXCEPTION - %lu - Unable to generate session route : unknown COS name [chars]

A Class of Service name specified for a session activation\n\ could not be associated with a valid COS.\n\ A session activation will fail with the specified sense code.

snasw

"Ensure no mode-to-COS mapping tables at the origin node or its\n\ network node server use the unrecognised COS."

SNASW-4-TS_LOG_1

4-Warning

EXCEPTION - %lu - Unable to generate session route - no suitable TGs from origin node [chars]

No suitable TG could be found from the origin end node to the\n\ backbone network for the class of service specified for a\n\ session activation. This may be caused by a temporary link\n\ failure between the origin node and a network node.\n\ A session activation will fail with the specified sense code.

snasw

"First check for a link failure at the origin node that explains\n\ the route failure. If no link failure is found either\n\ - change the mode-to-COS mapping on the origin node or its\n\ network node server to use a different class of service or\n\ - reconfigure the network to ensure there is a usable route\n\ from the origin node to the backbone network for example by\n\ defining and/or activating another link from the origin node\n\ to a network node."

SNASW-4-TS_LOG_2

4-Warning

EXCEPTION - %lu - Unable to generate session route - no suitable TGs to destination node [chars]

No suitable TG could be found from the backbone network to the\n\ destination end node for the class of service specified for a\n\ session activation. This may be caused by a temporary link\n\ failure between the destination node and a network node.\n\ A session activation will fail with the specified sense code.

snasw

"First check for a link failure at the destination node that\n\ explains the route failure. If no link failure is found\n\ either\n\ - change the mode-to-COS mapping on the origin node or its\n\ network node server to use a different class of service or\n\ - reconfigure the network to ensure there is a useable route\n\ from the destination node to the backbone network for\n\ example by defining and/or activating another link from the\n\ destination node to a network node."

SNASW-4-TS_LOG_6

4-Warning

EXCEPTION - %lu - Unable to generate session route to adjacent node [chars]

No suitable TG could be found for a session activation to an\n\ adjacent node for the given Class of Service. This may be\n\ caused by a link failure.\n\ A session activation will fail with the specified sense code.

snasw

"Check for a link failure that explains the failure.\n\ If no link failure is found reconfigure the network to ensure\n\ there is a useable link between this node and the specified\n\ adjacent node."

SNASW-4-TS_LOG_7

4-Warning

EXCEPTION - %lu - Unable to generate session route - RSCV truncated [chars]

-

snasw

"Reconfigure the network to ensure there is a short enough\n\ route between the origin and destination nodes."

SNASW-3-TS_LOG_13

3-Error

PROBLEM - %lu - Failed to send alert due to insufficient memory [chars]

Insufficient Memory was available to send an Alert.\n\ The Host will not see an Alert. The alert number below\n\ identifies the alert\n\ 1 - CPDB001\n\ 2 - CPDB002\n\ 3 - CPDB003\n\ 46 - CPDB004\n\ 57 - CPDB005\n\ The alerts are detailed in the Management Services Reference\n\ C30-3346\n\msgdef_recommended_action Either decrease the system load

-

-

SNASW-3-DS_LOG_1

3-Error

PROBLEM - %lu - Network search not started because it would exceed the maximum number of concurrent locates supported by this node [chars]

Network search not started because it would exceed the maximum\n\ number of concurrent locates supported by this node.\n\ Session activation will fail with the specified sense code.

snasw

"Collect trace and report the problem to support."

SNASW-4-DS_LOG_2

4-Warning

EXCEPTION - %lu - Locate search failed: search error [chars]

-

snasw

"Retry the session activation. If the problem persists\n\ contact support with details of the problem."

SNASW-3-DS_LOG_3

3-Error

PROBLEM - %lu - Received badly formed Locate from an adjacent node [chars]

Received badly formed Locate from an adjacent node. This may\n\ indicate an interoperability problem. Sense codes are as\n\ follows.\n\ 1010B080 - missing command parameters control vector in\n\ Found GDS variable\n\ 10140080 - GDS variable or control vector length error\n\ 1014A082 - missing search argument directory entry in Find\n\ GDS variable\n\ CP-CP sessions with adjacent node will be deactivated with the\n\ specified sense code.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_4

3-Error

PROBLEM - %lu - Insufficient storage to process Locate received from adjacent node [chars]

Insufficient storage to process Locate received from adjacent\n\ node.\n\ CP-CP sessions with the adjacent node will be deactivated this\n\ avoids possible deadlocks.

snasw

-

SNASW-4-DS_LOG_5

4-Warning

EXCEPTION - %lu - Received Locate with no Find GDS variable [chars]

Received Locate with no Find GDS variable.\n\ None the Locate is discarded.

snasw

"None."

SNASW-3-DS_LOG_9

3-Error

PROBLEM - %lu - Insufficient storage for CP-CP sessions [chars]

Insufficient storage for CP-CP sessions.\n\ CP-CP sessions will be deactivated with the specified sense\n\ code.

snasw

-

SNASW-4-DS_LOG_10

4-Warning

EXCEPTION - %lu - CP-CP sessions deactivated while broadcast Locate outstanding [chars]

CP-CP sessions deactivated while broadcast Locate in process.\n\ Session activation may fail.

snasw

"This log simply flags the fact that a session failure impacted\n\ a pending broadcast Locate. Other more specific logs give\n\ reasons for the session failure and appropriate actions."

SNASW-3-DS_LOG_11

3-Error

PROBLEM - %lu - Received registration or deletion request from an unknown end node [chars]

Received a registration or deletion request from an unknown\n\ end node. This may indicate an interoperability problem but\n\ is not considered fatal.\n\ The registration request is discarded.

snasw

"None."

SNASW-3-DS_LOG_12

3-Error

PROBLEM - %lu - Insufficient storage to register resources owned by a served end node [chars]

Insufficient storage to register resources owned by a served\n\ end node.\n\ The specified resource will not be registered and the\n\ registration request rejected. Network searches for the\n\msgdef_recommended_action Either decrease the system load

-

-

SNASW-3-DS_LOG_13

3-Error

PROBLEM - %lu - Resource registration failure: resource already registered [chars]

Failed to register resource for a served end node because the\n\ resource is already registered but with a different parent\n\ resource. This typically occurs when the same LU is defined\n\ on two or more end nodes.\n\ The registration request is rejected which may result in\n\ other resources not being registered and subsequent network\n\ search failures.

snasw

"Remove or rename the LU on one of the end nodes."

SNASW-3-DS_LOG_14

3-Error

PROBLEM - %lu - Registration failure notification received from network node server is badly formed [chars]

Registration failure GDS variable received from the network\n\ node server is badly formed. This may indicate an\n\ interoperability problem.\n\ CP-CP sessions to node will be deactivated.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_15

3-Error

PROBLEM - %lu - Link/session failure while registering resources with network node server [chars]

Link or session failure while registering resources with the\n\ network node server.\n\ CP-CP sessions to node will be deactivated.

snasw

"This log flags the fact that a registration request was\n\ disrupted by the link or session failure. Other more specific\n\ logs give details on the reasons for the failure and the\n\ appropriate actions."

SNASW-3-DS_LOG_17

3-Error

PROBLEM - %lu - Protocol error while registering resources with network node server [chars]

Protocol error while registering resources with the network\n\ node server.\n\ CP-CP sessions to node will be deactivated.

snasw

"Contact support with details of the problem."

SNASW-4-DS_LOG_18

4-Warning

EXCEPTION - %lu - Locate search timed out [chars]

-

snasw

"Verify that there are no nodes in the network with a single\n\ CP-CP session active to an adjacent node."

SNASW-3-DS_LOG_21

3-Error

PROBLEM - %lu - Served end node attempted to delete a home directory entry [chars]

A served end node attempted to delete a directory entry that is\n\ defined as a home entry at this node. This normally occurs\n\ when snasw location has been used to define LUs owned by served\n\ end or LEN nodes. The Delete request is rejected with the\n\ specified sense code.

snasw

"Use no snasw location to remove the home entry from the directory."

SNASW-4-DS_LOG_22

4-Warning

EXCEPTION - %lu - Served end node attempted to delete a non-existant directory entry [chars]

A served end node attempted to delete a directory entry that\n\ does not exist. This is normally caused by a network race\n\ condition causing the Delete request to arrive when the\n\ resource has not been registered.\n\ The Delete request is rejected with the specified sense code.

snasw

"None."

SNASW-3-DS_LOG_23

3-Error

PROBLEM - %lu - Served end node attempted to delete a resource it doesn't own [chars]

Served end node attempted to delete a resource when it was not\n\ registered as the owner of the resource. This may indicate an\n\ interoperability problem.\n\ The Delete request is rejected with the specified sense code.\n\ This may cause the end node to deactivate CP-CP sessions.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_24

3-Error

PROBLEM - %lu - Received Register/Delete GDS variable containing format errors [chars]

Received a Register or Delete GDS variable from a served\n\ end node which contained format errors. Sense codes are as\n\ follows.\n\ 08950000 - GDS variable or control vector length error.\n\ 10140080 - invalid control vector\n\ Register or delete attempt is rejected. The resources\n\ specified will not be registered

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_26

3-Error

PROBLEM - %lu - Unable to register resources because this node is not authorised at the network node server [chars]

-

snasw

"Modify the network node server configuration to\n\ consider this node authorised."

SNASW-3-DS_LOG_27

3-Error

PROBLEM - %lu - Unable to register resources because the network node server's directory is full [chars]

A resource registration failed because the network node\n\ server's directory is full. This may indicate a shortage of\n\ storage at the network node or a configured upper bound on\n\ the size of it's directory.\n\ No further resource registration will occur until CP-CP\n\ sessions are deactivated and reestablished.

snasw

"Increase the size of the directory at the network server. This\n\ may be a simple configuration change or it may require freeing\n\ up storage by reducing the load at the server."

SNASW-3-DS_LOG_28

3-Error

PROBLEM - %lu - Resource registration failed because the resource conflicted with an existing entry in the network node's directory [chars]

A resource registration failed because the resource conflicted\n\ with existing resources in the network node server's\n\ directory. This most commonly occurs when two LUs with the\n\ same name are defined on two different end nodes being served\n\ by the same network node. It may also occur if the network\n\ node has a home directory entry defined for the same resource.\n\ Registration of the resource in question will fail other\n\ resources should still be registered correctly.

snasw

"Check the network node's directory for the duplicate entry. If\n\ it is a home entry then remove the home entry from the\n\ directory. If it is a registered entry owned by a different\n\ end node redefine the LU to use a different name."

SNASW-3-DS_LOG_29

3-Error

PROBLEM - %lu - Resource registration failed because network node server detected a protocol error in the Register request [chars]

A resource registration failed because the network node server\n\ detected a protocol error in the Register request. This may\n\ indicate an interoperability problem.\n\ Registration of the resource in question will fail other\n\ resources should still be registered correctly.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_30

3-Error

PROBLEM - %lu - Resource registration failed with an unknown sense code [chars]

A resource registration failed with an unknown sense code.\n\ This may indicate an interoperability problem.\n\ No further resource registration will occur until CP-CP\n\ sessions are deactivated and reestablished.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_31

3-Error

PROBLEM - %lu - Delete failure reply received with sense code that is unrecoverable [chars]

Delete reply received with a sense code that is unrecoverable.\n\ CP-CP sessions to node will be deactivated.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_32

3-Error

PROBLEM - %lu - Unable to correlate received Register or Delete reply to a directory entry [chars]

Directory Error Correlator returned on a Register or Delete\n\ reply cannot be correlated to a directory entry. This is\n\ considered a protocol error and may indicate an\n\ interoperability problem.\n\ CP-CP sessions to node will be deactivated.

snasw

"Contact support with details of the problem."

SNASW-3-DS_LOG_33

3-Error

PROBLEM - %lu - Unable to delete resources because this node is not authorised at the network node server [chars]

-

snasw

"Modify the network node server configuration to\n\ consider this node authorised."

SNASW-4-DS_LOG_34

4-Warning

EXCEPTION - %lu - Delete request failed because the resource was not found or not removable [chars]

A Delete request failed either because the entry was defined\n\ as a home entry at the network node server or because the\n\ resource was not found. Neither error is severe and will\n\ not affect future registration and deletion or other aspects\n\ of network operation.\n\ Delete attempt has failed further deletion and registration\n\ will continue unaffected.

snasw

"None."

SNASW-4-DS_LOG_35

4-Warning

EXCEPTION - %lu - Register GDS variable received with an invalid resource name [chars]

Invalid resource name in received register request.\n\ Register request will fail.

snasw

"Contact support with details of the problem."

SNASW-4-DS_LOG_36

4-Warning

EXCEPTION - %lu - Central Resource Registration failure [chars]

Central Resource Registration failure.\n\ Network performance may degrade because of additional broadcast\n\ Locate searches.

snasw

"None."

SNASW-4-DS_LOG_37

4-Warning

EXCEPTION - %lu - Central Resource Registration failure: invalid correlator received [chars]

Central Resource Registration failure and invalid correlator\n\ received.\n\ Network performance may degrade because of additional broadcast\n\ Locate searches.

snasw

"None."

SNASW-6-DS_LOG_38

6-Information

INFO - %lu - Central Directory Server located [chars]

Central Directory Server located.

snasw

"None"

SNASW-3-DS_LOG_40

3-Error

PROBLEM - %lu - Locate received from adjacent node exceeded the maximum number of concurrent locates supported by this node [chars]

Locate received from adjacent node exceeded the maximum number\n\ of concurrent locates supported by this node.\n\ CP-CP sessions with the adjacent node will be deactivated this\n\ avoids possible deadlocks.

snasw

-

SNASW-3-DS_LOG_41

3-Error

PROBLEM - %lu - Insufficient storage to start a network search [chars]

Insufficient storage to start a network search.\n\ Session activation will fail with the specified sense code.

snasw

"Make more resource available to SNA Switch."

SNASW-3-DS_LOG_42

3-Error

PROBLEM - %lu - CP-CP sessions deactivated while directed Locate outstanding [chars]

CP-CP sessions deactivated while directed Locate in process.\n\ Session activation may fail.

snasw

"This log simply flags the fact that a session failure impacted\n\ a pending directed Locate. Other more specific logs give\n\ reasons for the session failure and appropriate actions."

SNASW-6-DS_LOG_43

6-Information

INFO - %lu - Locate search failed: LU not found [chars]

A network search for which this node was the originator or the\n\ network node server failed to locate the target LU. This may\n\ be caused by the target LU name being incorrect the target\n\ system being inoperative or by link errors in the backbone of\n\ the network.\n\ Session activation will fail with the specified sense code.

snasw

"If the target LU name is correct check that the system the\n\ LU is defined on is active. If the system is active check\n\ the topology of the network to ensure that the target system\n\ or its network node server is reachable from this node."

SNASW-4-DS_LOG_44

4-Warning

EXCEPTION - %lu - CP-CP sessions established with end node: invalid directory entry removed [chars]

CP-CP sessions have been established with an adjacent end node\n\ which was previously defined using snasw location.\n\ The invalid directory definitions for the end node and any of\n\ its LUs will be removed.

snasw

"Do not configure the invalid entries in future."

SNASW-4-SC_LOG_1

4-Warning

EXCEPTION - %lu - Protocol error detected in PIU on intermediate session [chars]

SNA Switch detected a protocol error in an PIU received on an\n\ intermediate session. This typically indicates a problem on\n\ an adjacent node. The sense codes are as follows.\n\ 10010003 - invalid IPM format\n\ 10020000 - RU length error\n\ 10030000 - CLEAR request on secondary stage or\n\ CLEAR response on primary stage\n\ 20110000 - sender has overrun pacing window or\n\ PI not set on first RU of window\n\ 20110001 - unexpected IPM\n\ 20110002 - PI set on other than first RU in window\n\ 20110003 - invalid pacing response\n\ 80070000 - segment error\n\ The intermediate session will be deactivated.

snasw

"Report the problem in the adjacent node to support running a\n\ trace on the specified link if more diagnostics are required"

SNASW-4-SC_LOG_2

4-Warning

EXCEPTION - %lu - Deactivating intermediate session because of insufficient storage [chars]

Deactivating intermediate session because of insufficient\n\ storage.\n\ The intermediate session will be deactivated.

snasw

-

SNASW-3-SCM_LOG_0

3-Error

PROBLEM - %lu - ISR session activation failed - ISR session limit reached [chars]

-

snasw

"Collect trace and report the problem to support."

SNASW-3-SCM_LOG_1

3-Error

PROBLEM - %lu - Protocol error in received ISR BIND request [chars]

Protocol error in received ISR BIND request. This may indicate\n\ an interoperability problem. Sense codes are as follows.\n\ 08350008 - secondary-to-primary staging indicator incorrect\n\ 0835000C - primary-to-secondary staging indicator incorrect\n\ 10010024 - unextended non-LU6.2 BIND\n\ 10020000 - BIND RU length error\n\ ISR session activation will fail with the specified sense code.

snasw

"Report the problem to support running a trace on the specified\n\ link if more diagnostics are required."

SNASW-3-SCM_LOG_3

3-Error

PROBLEM - %lu - Unable to identify or activate the next hop of an ISR session [chars]

Unable to identify or activate the next hop of an ISR session.\n\ ISR session activation will fail with the specified sense code.

snasw

"This log is preceded by other logs giving more specific reasons\n\ for the failure. Follow the actions given in those logs."

SNASW-3-SCM_LOG_4

3-Error

PROBLEM - %lu - Fatal error detected in ISR session [chars]

ISR detected a fatal error in an intermediate session.\n\ The ISR session will be deactivated with the specified sense\n\ code.

snasw

"This log should be preceded by a log 536 or 537. Follow the\n\ actions given in those logs."

SNASW-3-SCM_LOG_5

3-Error

PROBLEM - %lu - ISR session failure because of link outage or error [chars]

ISR session failed because of link outage or error.\n\ The ISR session will be deactivated with the specified sense\n\ code.

snasw

"This log gives information on which ISR sessions are affected\n\ by a link outage or error. Preceding logs give more specific\n\ information about the reason for the link outage or error."

SNASW-3-SCM_LOG_6

3-Error

PROBLEM - %lu - Unable to assign LFSID to secondary stage of ISR session [chars]

-

snasw

"This log gives information on which ISR session is affected by\n\ a failure in the LFSID table management. Preceding logs give\n\ more detail on the reason for the failure."

SNASW-4-SCM_LOG_7

4-Warning

EXCEPTION - %lu - Unable to correlate BIND response received during ISR session activation [chars]

Unable to correlate BIND response received during ISR session\n\ activation.\n\ None. This is a normal race condition caused by a BIND request\n\ being immediately followed by an UNBIND request for the same\n\ session.

snasw

"None."

SNASW-4-SCM_LOG_8

4-Warning

EXCEPTION - %lu - Unable to correlate UNBIND request received for an ISR session [chars]

-

snasw

"None."

SNASW-6-SCM_LOG_9

6-Information

INFO - %lu - ISR Session Activated [chars]

An ISR Session has been activated

snasw

"None"

SNASW-6-SCM_LOG_10

6-Information

INFO - %lu - ISR Session Deactivated [chars]

An ISR Session has been deactivated

snasw

"None"

SNASW-3-SCM_LOG_11

3-Error

PROBLEM - %lu - Received ISR BIND request with duplicate FQPCID [chars]

Received ISR BIND request with duplicate FQPCID.\n\ ISR session activation will fail with the specified sense code.\n\ 083B0002

snasw

"Report the problem to support running a trace on the specified\n\ link if more diagnostics are required."

SNASW-3-SCM_LOG_12

3-Error

PROBLEM - %lu - Protocol error in received ISR BIND request [chars]

Protocol error in received ISR BIND response. This may\n\ indicate an interoperability problem. Sense codes are as\n\ follows.\n\ 08350007 - control vectors included indicator incorrect\n\ 08350008 - secondary-to-primary staging indicator incorrect\n\ 0835000C - primary-to-secondary staging indicator incorrect\n\ 086F0000 - BIND response length inconsistent\n\ 10010024 - unextended non-LU6.2 BIND response\n\ 10020000 - BIND RU length error\n\ ISR session activation will fail with the specified sense code.

snasw

"Report the problem to support running a trace on the specified\n\ link if more diagnostics are required."

SNASW-3-SCM_LOG_13

3-Error

PROBLEM - %lu - ISR is unable to support requested RU size [chars]

ISR is unable to support RU size requested on non-negotiable\n\ BIND request or response. Sense codes are as follows.\n\ 0835000A - maximum secondary send RU size is larger than that\n\ supported by ISR\n\ 0835000B - maximum primary send RU size is larger than that\n\ supported by ISR\n\ ISR session activation will fail with the specified sense code.

snasw

"Collect trace and report the problem to support."

SNASW-3-SCM_LOG_14

3-Error

PROBLEM - %lu - ISR is unable to support requested pacing window size [chars]

ISR is unable to support fixed receive pacing window requested\n\ on non-negotiable BIND request or response. Sense codes are as\n\ follows.\n\ 08350009 - maximum primary send window size is larger than\n\ that supported by ISR\n\ 0835000D - maximum secondary send window size is larger than\n\ that supported by ISR\n\ ISR session activation will fail with the specified sense code.

snasw

"Collect trace and report the problem to support."

SNASW-3-SCM_LOG_15

3-Error

PROBLEM - %lu - Insufficient storage to activate ISR session [chars]

Insufficient storage to activate ISR session\n\ ISR session activation will fail with the specified sense code\n\ 08120014.

snasw

-

SNASW-3-SCM_LOG_16

3-Error

PROBLEM - %lu - Slow session activation detected [chars]

A session activation was started but has not completed after\n\ a significant time.

snasw

"If the session does not become active contact support with details of\n\ this log. "

SNASW-6-LM_LOG_0

6-Information

INFO - %lu - An LU-SSCP session has been activated for LU type 012 or 3 [chars]

An LU-SSCP session has been activated.

snasw

"None"

SNASW-6-LM_LOG_1

6-Information

INFO - %lu - A PLU-SLU session has been activated for LU type 012 or 3 [chars]

A PLU-SLU session has been activated.

snasw

"None"

SNASW-6-LM_LOG_2

6-Information

INFO - %lu - An LU-SSCP session has been deactivated for LU type 012 or 3 [chars]

An LU-SSCP session has been deactivated.

snasw

"None"

SNASW-6-LM_LOG_3

6-Information

INFO - %lu - A PLU-SLU session has been deactivated for LU type 012 or 3 [chars]

A PLU-SLU session has been deactivated.

snasw

"None"

SNASW-3-LM_LOG_4

3-Error

PROBLEM - %lu - Insuffcient storage to dyamically define dependent LU with host [chars]

Insufficient storage to dynamically define dependent LU with\n\ host.\n\ LU-SSCP session will not be activated.

snasw

-

SNASW-3-LM_LOG_5

3-Error

PROBLEM - %lu - Insufficient storage to BIND LU type 012 or 3 PLU-SLU session as PLU [chars]

Insufficient storage to BIND LU type 012 or 3 PLU-SLU\n\ session.\n\ BIND request will not be sent.

snasw

-

SNASW-4-LM_LOG_6

4-Warning

EXCEPTION - %lu - Insufficient storage to send RTM statistics to host [chars]

Insufficient storage to send RTM statistics to host.\n\ RTM statistics displayed by host will be inconsistent.

snasw

-

SNASW-4-LM_LOG_7

4-Warning

EXCEPTION - %lu - Insufficient storage to report RTM status to application [chars]

Insufficient storage to report RTM status to application.\n\ RTM statistics reported and displayed by application may be\n\ inconsistent.

snasw

-

SNASW-3-LM_LOG_12

3-Error

PROBLEM - %lu - Insufficient storage to activate LU-SSCP session for LU type 012 or 3 as SSCP [chars]

Insufficient storage to activate LU-SSCP session for LU type\n\ 012 or 3.\n\ ACTLU request will not be sent.

snasw

-

SNASW-3-LM_LOG_13

3-Error

PROBLEM - %lu - Insufficient storage to activate LU type 012 or 3 PLU-SLU session as SLU [chars]

Insufficient storage to activate LU type 012 or 3 PLU-SLU\n\ session.\n\ BIND request will be rejected with the specified sense code.

snasw

-

SNASW-3-LM_LOG_14

3-Error

PROBLEM - %lu - Insufficient storage to activate LU-SSCP session for LU type 012 or 3 as LU [chars]

Insufficient storage to activate LU-SSCP session for LU type\n\ 012 or 3.\n\ ACTLU request will not be rejected with the specified sense\n\ code.

snasw

-

SNASW-3-LM_LOG_15

3-Error

PROBLEM - %lu - A BIND request received by an LU type 012 or 3 was rejected by SNA Switch because it failed parameter checks [chars]

-

snasw

"If possible investigate the configuration of the system that\n\ sent the BIND request.\n\ If a configuration error is found then correct it otherwise\n\ contact support with details of the problem."

SNASW-3-LM_LOG_16

3-Error

PROBLEM - %lu - A BIND request received by an LU type 012 or 3 was rejected by an application connected to SNA Switch [chars]

A BIND request received by an LU type 012 or 3 was rejected\n\ by an application connected to SNA Switch.\n\ BIND request will be rejected with the specified sense code.\n\ PLU-SLU session is not activated.

snasw

-

SNASW-3-LM_LOG_17

3-Error

PROBLEM - %lu - A BIND request received by an LU type 012 or 3 was rejected by SNA Switch because the application connection was not open [chars]

A BIND request received by an LU type 012 or 3 was rejected\n\ because the application connection was not open. This may be\n\ caused by a normal window condition or it may indicate that the\n\ system that sent the BIND request is incorrectly configured or\n\ is defective.\n\ BIND request will be rejected with the specified sense code.\n\ PLU-SLU session is not activated.

snasw

"Investigate the cause of the problem. If it indicates that the\n\ system that sent the BIND request is incorrectly configured\n\ then correct the configuration error. If it appears that the\n\ system is defective then contact support with details of the\n\ problem."

SNASW-4-LM_LOG_18

4-Warning

EXCEPTION - %lu - An LU-SSCP session activation attempt failed because the SSCP was not suitable [chars]

An ACTLU was received for an LU from the wrong SSCP.\n\ The ACTLU is rejected with sense code 084B0000 i.e. the LU\n\ activation attempt fails.

snasw

-

SNASW-3-LM_LOG_19

3-Error

PROBLEM - %lu - An UNBIND RSP was received at a secondary LU [chars]

An UNBIND RSP was received at a secondary LU. This is illegal\n\ SNA as no UNBIND RQ was sent.\n\ The UNBIND RSP is dropped.

snasw

"The session may not be coming down properly. Check that\n\ dependent LU applications are correctly replying to all\n\ signals. Otherwise contact support with details of the\n\ problem."

SNASW-4-DLUR_LOG_1

4-Warning

EXCEPTION - %lu - UNBIND could not be correlated to DLUR-served LU [chars]

-

snasw

"None."

SNASW-3-DLUR_LOG_2

3-Error

PROBLEM - %lu - REQACTPU rejected [chars]

DLUS rejects REQACTPU with given sense code.\n\ An SSCP-PU session with the given DLUS will not be activated.\n\ If a backup DLUS is configured for the PU DLUR will attempt\n\ to activate the PU via the backup DLUS.

snasw

"Examine sense code and retry activation if appropriate."

SNASW-4-DLUR_LOG_5

4-Warning

EXCEPTION - %lu - CPSVRMGR pipe session failure [chars]

-

snasw

"If a pipe with backup DLUS is not initiated automatically\n\ manually restart any required PUs"

SNASW-4-DLUR_LOG_8

4-Warning

EXCEPTION - %lu - Inconsistent DLUS Names [chars]

Inconsistent DLUS Names.\n\ The Host has requested the activation of a Downstream link to\n\ a PU by sending an ACTPU. The link is configured to request\n\ a different DLUS.\n\ The DLUS initiating the activation is used.

snasw

-

SNASW-4-DLUR_LOG_9

4-Warning

EXCEPTION - %lu - Protocol Error from DLUS Host: RU Size too large for SSCP Session [chars]

Protocol Error from DLUS. Received an RU too large for SSCP\n\ Session. This is typically due to the SSCP sending too large\n\ a LOGON Screen.\n\ The Data is thrown away.

snasw

"If you are expecting an SSCP LOGON screen enter your LOGON\n\ command as usual.\n\ "

SNASW-4-DLUR_LOG_10

4-Warning

EXCEPTION - %lu - Failed to contact a DLUS for PU. Retry count exceeded. [chars]

The DLUR has failed to contact either the DLUS or the backup/\n\ default DLUSs after the configured number of retries.\n\ Contact is not made with the DLUS.

snasw

"Check earlier logs for causes of individual failures to contact\n\ Host. Resolve any problems or increase the timeout or retry\n\ count and try again.\n\ "

SNASW-3-DLUR_LOG_11

3-Error

PROBLEM - %lu - Received PLU-SLU BIND request with duplicate FQPCID [chars]

Received PLU-SLU BIND request with duplicate FQPCID.\n\ Session activation will fail with the specified sense code.\n\ 083B0002

snasw

"Report the problem to support running a trace on the specified\n\ link if more diagnostics are required."

SNASW-6-DLUR_LOG_12

6-Information

INFO - %lu - A pipe to a DLUS has activated [chars]

A pipe to a DLUS has activated.

snasw

"None"

SNASW-6-DLUR_LOG_13

6-Information

INFO - %lu - A pipe to a DLUS has deactivated [chars]

A pipe to a DLUS has deactivated.

snasw

"None"

SNASW-4-DLUR_LOG_14

4-Warning

EXCEPTION - %lu - An attempt to activate a persistent pipe to a DLUS has failed [chars]

DLUR has requested a persistent pipe to a DLUS but the DLUS\n\ does not support persistent pipes.\n\ The sense codes are as follows.\n\ 088E0009 - the DLUR has failed the pipe activation because it\n\ requires all pipes to be persistent.\n\ 08A0000C - the DLUS has failed the pipe activation because\n\ there is no PU needing service.\n\ The attempt to activate a persistent pipe to the DLUS will\n\ fail.

snasw

"If the DLUR is unable to contact a different DLUS that does\n\ support persistent pipes then the following should be\n\ considered.\n\ If the sense code is 088E0009 then DLUR requirement for\n\ persistent pipes could be removed.\n\ Otherwise the DLUS must be upgraded to support persistent\n\ pipes."

SNASW-4-DLUR_LOG_15

4-Warning

EXCEPTION - %lu - A DLUS has sent an ACTPU without a PU name [chars]

A DLUS has sent an ACTPU without a PU name.\n\ The ACTPU will be rejected with the specified sense code. PU\n\ activation will not continue.

snasw

"Check the status of the named DLUS. Check that it is correctly\n\ configured. Optionally reconfigure SNA Switch to use a\n\ different DLUS."

SNASW-4-DLUR_LOG_16

4-Warning

EXCEPTION - %lu - A DLUS has sent an ACTPU with a PU name that is already in use [chars]

A DLUS has sent an ACTPU with a PU name that is already in use.\n\ The ACTPU will be rejected with the specified sense code. PU\n\ activation will not continue.

snasw

"Reconfigure the DLUS or the DLUR to use different PU names.\n\ If the DLUS and the DLUR use the same PU name then they must\n\ apply the name to the same PU."

SNASW-4-DLUR_LOG_17

4-Warning

EXCEPTION - %lu - A DLUS has sent an ACTPU with a PU name different from the name in the last ACTPU received for the same DSPU. [chars]

A DLUS has sent an ACTPU with a PU name that is different to\n\ the PU name in the last ACTPU received for the same DSPU.\n\ The PU name of this implicit or DLUS-defined DSPU will change\n\ its name to the name from this new ACTPU.

snasw

-

SNASW-4-DLUR_LOG_18

4-Warning

EXCEPTION - %lu - Failed to contact one or both of the default DLUS when attempting to activate a persistent pipe required by a DLUS-dependent port. The retry count is exceeded. [chars]

The DLUR has failed to contact either the default primary DLUS\n\ or the default backup DLUS or both after the configured number\n\ of retries when attempting to activate a persistent pipe\n\ required to enable a DLUS-dependent port.\n\ The DLUS-dependent port is not enbaled.

snasw

"Check earlier logs for causes of individual failures to contact\n\ Host. Resolve any problems or increase the timeout or retry\n\ count and try again."

SNASW-6-DLUR_LOG_19

6-Information

INFO - %lu - Deactivating a persistent pipe because it is not required [chars]

The DLUR is deactivating a persistent pipe because it is not\n\ required to keep it active.

snasw

"None"

SNASW-4-DLUR_LOG_20

4-Warning

EXCEPTION - %lu - Invalid MU type received by DLUR [chars]

An invalid MU type has been received by DLUR from an internal\n\ or downstream PU.\n\ None the invalid MU will be discarded.

snasw

"If this is an internal PU then contact support with details of\n\ this log. If this is a downstream PU then contact the supplier\n\ of the downstream node."

SNASW-4-DLUR_LOG_21

4-Warning

EXCEPTION - %lu - Different PUs have LUs whose names clash [chars]

Two LUs of the same name exist under different PUs. One is\n\ already activated and DLUS has attempted to activate the other.\n\ The second LU will not be activated.

snasw

"Rename one of the LUs with a unique network name."

SNASW-4-DLUR_LOG_22

4-Warning

EXCEPTION - %lu - PU not found for REQACTPU RSP or REQDACTPU [chars]

A REQACTPU RSP or REQDACTPU has been recevied and the node has\n\ not been able to correlate it to a PU_CB.\n\ The REQDACTPURSP will be discarded.

snasw

"Contact the supplier of the DLUS with details of this log."

SNASW-4-DLUR_LOG_23

4-Warning

EXCEPTION - %lu - A REQACTPU RSP has not been received. Possible hung PU problem [chars]

A REQACTPU RSP has not been received for this PU and it appears\n\ the PU is hung.\n\ There will be no further action taken

snasw

"If this is an internal PU then contact support with details of\n\ this log. If this is a downstream PU then contact the supplier\n\ of the downstream node."

SNASW-6-DLUR_LOG_24

6-Information

INFO - %lu - A PU previously logged as possibly hung is no longer possibly hung [chars]

A PU that had previously been logged as hung is now not\n\ believed to be hung.\n\ There will be no further action taken

snasw

"None."

SNASW-3-DLUR_LOG_25

3-Error

PROBLEM - %lu - A new DSPU has activated with the same node ID and CP name as an existing DSPU [chars]

-

snasw

"Change the node ID or CP name on one of the DSPUs."

SNASW-4-HPR_LOG_0

4-Warning

EXCEPTION - %lu - HPR Route Setup RU received with format errors [chars]

An HPR Route Setup RU has been received with format errors\n\ The message cannot be processed and will be discarded.

snasw

"Report error to remote end."

SNASW-4-HPR_LOG_1

4-Warning

EXCEPTION - %lu - Unable to correlate HPR Route Setup RU [chars]

Unable to correlate HPR Route Setup Reply\n\ The message cannot be processed and will be discarded.

snasw

"Report error to remote end."

SNASW-3-HPR_LOG_2

3-Error

PROBLEM - %lu - Unable to activate RTP connection [chars]

Unable to activate RTP Connection\n\ In certain situations the origin may retry activation.

snasw

"Examine sense code and retry activation if appropriate."

SNASW-4-HPR_LOG_3

4-Warning

EXCEPTION - %lu - Link failure caused HPR route setup request to be dropped [chars]

Link failure between this node and source of Route Setup req\n\ The route setup request is dropped by this node.\n\ The partner node on that link should generate -ve reply.

snasw

"Investigate link failure."

SNASW-4-HPR_LOG_4

4-Warning

EXCEPTION - %lu - HPR manager failed to obtain memory to send indication [chars]

HPR manager failed to get memory to send an RTP\n\ indication.\n\ The data_lost flag will be set in the next indication\n\ successfully sent.

snasw

"Investigate memory shortage."

SNASW-4-HPR_LOG_5

4-Warning

EXCEPTION - %lu - NLP received with format errors [chars]

An NLP has been received with format errors\n\ The message cannot be processed and will be discarded.

snasw

"Report error to remote end."

SNASW-4-HPR_LOG_6

4-Warning

EXCEPTION - %lu - NLP received for RTP connection which no longer exists [chars]

An NLP has been received for an RTP connection which no\n\ longer exists\n\ The message cannot be processed and will be discarded.

snasw

"Report error to remote end."

SNASW-4-HPR_LOG_8

4-Warning

EXCEPTION - %lu - Connection Setup NLP received for previous NCE instance [chars]

A connection setup NLP has been received specifying a\n\ previous instance of this NCE. The NCE must have been\n\ shut down and restarted since processing the Route Setup\n\ request\n\ No RTP connection can be started so the NLP will be discarded.

snasw

"Report error to remote end."

SNASW-4-HPR_LOG_9

4-Warning

EXCEPTION - %lu - Local node has received a HPR Route Setup RU that it cannot forward because the next hop is not HPR-capable so is replying with the backout sense code [chars]

-

snasw

"None."

SNASW-4-HPR_LOG_10

4-Warning

EXCEPTION - %lu - Local node has received a HPR Route Setup RU that it cannot forward because the next hop is not HPR-capable so is acting as the new destination [chars]

-

snasw

"None."

SNASW-4-HPR_LOG_11

4-Warning

EXCEPTION - %lu - The local node is acting as the new destination for a backed-out Route Setup [chars]

-

snasw

"None."

SNASW-4-HPR_LOG_12

4-Warning

EXCEPTION - %lu - A Route Setup has been backed out from the orignal destination to the new destination [chars]

-

snasw

"None."

SNASW-4-HPR_LOG_13

4-Warning

EXCEPTION - %lu - A Route Setup Reply has been received with the backout sense code HPR will not be used for this session [chars]

The local node has received an HPR Route Setup Reply with\n\ the backout sense code. The Route Setup has failed because the\n\ destination node does not support RTP. No intermediate node\n\ supports RTP and was able to become the new destination.\n\ The Route Setup has failed and HPR will not be used for the\n\ session that is being activated.\n\ This is a normal event when a node in the route has an\n\ auto-activateable link to a node that does not support RTP or\n\ HPR.

snasw

"None."

SNASW-4-HPR_LOG_14

4-Warning

EXCEPTION - %lu - Local node is the destination of a HPR Route Setup RU but does not support RTP so is replying with the backout sense code [chars]

-

snasw

"None."

SNASW-4-HPR_LOG_15

4-Warning

EXCEPTION - %lu - Remote NCE has restarted so disconnect this RTP connection with previous instance of that NCE [chars]

A connection setup NLP has been received from a remote NCE\n\ which has shut down and restarted. An RTP connection still\n\ exists from that NCE before it shut down.\n\ The old RTP connection will be disconnected

snasw

"None."

SNASW-4-HPR_LOG_16

4-Warning

EXCEPTION - %lu - Unable to activate Route Setup RTP connection [chars]

Unable to activate a Route Setup RTP Connection during\n\ processing of a Route Setup request.\n\ The Route Setup request will fail with the sense code shown.\n\ The next Route Setup request will trigger another attempt\n\ to activate the Route Setup RTP Connection.

snasw

-

SNASW-4-HPR_LOG_17

4-Warning

EXCEPTION - %lu - Connection Setup NLP rejected because it specified unsupported Topic ID [chars]

A Connection Setup NLP was rejected because it specified the\n\ CP-CP session or Route Setup Topic ID but was received on a TG\n\ which does not support the Control Flows over RTP Tower.\n\ The CP-CP session or Route Setup RTP Connection will fail with\n\ sense code HA0010017.

snasw

"Contact support with details of the problem."

SNASW-4-HPR_LOG_18

4-Warning

EXCEPTION - %lu - HPR Route Setup RU received with existing FQPCID [chars]

An HPR Route Setup RU has been received with an FQPCID that\n\ matches an existing route.\n\ The message will be rejected and the route not established.

snasw

"Report error to remote end."

SNASW-3-HPR_LOG_20

3-Error

PROBLEM - %lu - Remote node supplied a corrupted RSCV: the next hop is the local CP [chars]

An HPR Route Setup RU has been received with an RSCV that gives\n\ the local node as the next ANR hop. This is invalid. Therefore\n\ the remote node is sending invalid protocol data.

snasw

"Report error to remote end."

SNASW-6-RTP_LOG_0

6-Information

INFO - %lu - RTP Connection has connected [chars]

The RTP Connection has connected

snasw

"None"

SNASW-6-RTP_LOG_1

6-Information

INFO - %lu - RTP Connection has disconnected [chars]

The RTP Connection has disconnected normally

snasw

"None"

SNASW-4-RTP_LOG_2

4-Warning

EXCEPTION - %lu - RTP Connection has disconnected [chars]

The RTP Connection has disconnected due to an error\n\ Sessions using the connection will fail

snasw

"Investigate the cause of the error"

SNASW-4-RTP_LOG_3

4-Warning

EXCEPTION - %lu - Remote end of RTP Connection has disconnected [chars]

The RTP Connection has disconnected due to an error\n\ Sessions using the connection will fail

snasw

"Investigate the cause of the error"

SNASW-4-RTP_LOG_4

4-Warning

EXCEPTION - %lu - RTP connection has timed-out [chars]

he RTP Connection has timed out\n\ The node will attempt to path-switch

snasw

"Investigate the cause of the error"

SNASW-4-RTP_LOG_5

4-Warning

EXCEPTION - %lu - RTP connection dropped due to local link failure [chars]

-

snasw

"Investigate the cause of the link failure"

SNASW-6-RTP_LOG_6

6-Information

INFO - %lu - Successful path-switch [chars]

he RTP Connection has successfully switched paths

snasw

"None"

SNASW-4-RTP_LOG_7

4-Warning

EXCEPTION - %lu - Path-switch failure [chars]

RTP connection has failed to path-switch\n\ The RTP connection will be disconnected

snasw

"Investigate the cause of the error"

SNASW-4-RTP_LOG_8

4-Warning

EXCEPTION - %lu - Segmented NLP received on Route Setup RTP connection [chars]

A Route Setup RTP Connection RTP process received a segmented\n\ NLP. This is an error because all NLPs received should contain\n\ Route Setup GDS data which should never be segmented.\n\ The NLP will be dropped.

snasw

"Contact support with details of the problem."

SNASW-4-RTP_LOG_9

4-Warning

EXCEPTION - %lu - RTP connection has timed-out [chars]

A Route Setup RTP Connection has timed out waiting for status\n\ from the adjacent node.\n\ The RTP Connection will be failed.

snasw

"Investigate the cause of the error at the adjacent node."

SNASW-4-RTP_LOG_10

4-Warning

EXCEPTION - %lu - LFSID in use moving on to next one. [chars]

An LFSID was found to be in use so SNA Switch is using a different one.

snasw

"If this log appears frequently inform your support contact."

SNASW-4-SS_LOG_4

4-Warning

EXCEPTION - %lu - Network Node server not required [chars]

-

snasw

"None."

SNASW-3-SS_LOG_5

3-Error

PROBLEM - %lu - CP capabilities exchange failed because of contention loser CP-CP session failure [chars]

CP capabilities exchange failed because of contention loser\n\ CP-CP session failure.\n\ Contention winner CP-CP session will be deactivated. SNA Switch\n\ will attempt to reactivate CP-CP sessions with this adjacent\n\ CP.

snasw

"This log flags the fact that a CP-CP session failed. Other\n\ logs give more details on the reason for the session failure\n\ eg. insufficient resources link failure."

SNASW-3-SS_LOG_7

3-Error

PROBLEM - %lu - Insufficient storage to generate Alert CPSS003 [chars]

Insufficient storage to generate Alert CPSS003 protocol error\n\ in received BIND or LOCATE.\n\msgdef_recommended_action Either decrease the system load

-

-

SNASW-3-SS_LOG_8

3-Error

PROBLEM - %lu - CP capabilities exchange failed because of protocol error [chars]

CP capabilities exchange has failed because of protocol error.\n\ This may indicate an interoperability problem. Sense codes are\n\ as follows.\n\ 08060030 - CP capabilities requested by unknown CP\n\ 08210002 - CP capabilities requested on other than CPSVCMG\n\ mode\n\ 08150007 - CP capabilities requested when CP-CP session\n\ already established\n\ 08B60000 - CP-CP sessions not supported by adjacent node\n\ 08090039 - CP transaction error\n\ CP-CP sessions with the specified adjacent node will be\n\ deactivated. SNA Switch will not attempt to reactivate CP-CP\n\ sessions with this adjacent CP.

snasw

"Contact support with details of the problem."

SNASW-3-SS_LOG_9

3-Error

PROBLEM - %lu - Protocol error in CP capabilities exchange [chars]

-

snasw

"Contact support with details of the problem."

SNASW-6-SS_LOG_11

6-Information

INFO - %lu - Adjacent CP contacted [chars]

Adjacent CP contacted.

snasw

"None"

SNASW-6-SS_LOG_12

6-Information

INFO - %lu - CP-CP sessions established [chars]

CP-CP sessions have been successfully established with the\n\ adjacent node.

snasw

"None"

SNASW-4-SS_LOG_13

4-Warning

EXCEPTION - %lu - Retrying CP-CP session activation after failure [chars]

Retrying CP-CP session establishment after error.\n\ None.

snasw

"None."

SNASW-3-SS_LOG_16

3-Error

PROBLEM - %lu - CP capabilities exchange failed because of contention winner CP-CP session failure [chars]

CP capabilities exchange failed because of contention winner\n\ CP-CP session failure.\n\ Contention loser CP-CP session will be deactivated. SNA Switch\n\ will attempt to reactivate CP-CP sessions with this adjacent\n\ CP.

snasw

"This log flags the fact that a CP-CP session failed. Other\n\ logs give more details on the reason for the session failure\n\ eg. insufficient resources link failure."

SNASW-4-SS_LOG_17

4-Warning

EXCEPTION - %lu - CP-CP sessions established between network nodes in different networks [chars]

CP-CP sessions established between two network nodes in\n\ different networks.\n\ CP-CP sessions will be deactivated with the specified sense\n\ code.

snasw

"None."

SNASW-6-SS_LOG_18

6-Information

INFO - %lu - CP-CP sessions deactivated [chars]

CP-CP sessions to the adjacent node have been deactivated.

snasw

"None"

SNASW-4-SS_LOG_19

4-Warning

EXCEPTION - %lu - Insufficient resources to register LU on adjacent LEN [chars]

Branch Network node has insufficient resources to register an\n\ LU on an adjacent LEN node.\n\ The LU resource may not be put into the directory and may not\n\ be accessible to other resources.

snasw

-

SNASW-4-SS_LOG_20

4-Warning

EXCEPTION - %lu - Automatic retry of CP-CP sessions on a timer has failed [chars]

The node failed to start a timer in order to retry CP-CP\n\ sessions to a Network Node Server.\n\ The node will not automatically attempt to activate CP-CP\n\ sessions and so may be left with no CP-CP sessions at all or\n\ CP-CP sessions with a node that is not the best available.\n\ CP-CP sessions will however be retried in the normal way when\n\ a local application needs them or a new link activates.

snasw

"None if CP-CP sessions are not required or if the administrator\n\ is happy with the existing Network Node Server. If the\n\ administrator wants to start CP-CP sessions they can be started\n\ manually."

SNASW-6-PU_LOG_0

6-Information

INFO - %lu - A PU-SSCP session has been activated [chars]

A PU-SSCP session has been activated.

snasw

"None"

SNASW-6-PU_LOG_1

6-Information

INFO - %lu - A PU-SSCP session has been deactivated [chars]

A PU-SSCP session has been deactivated.

snasw

"None"

SNASW-4-PU_LOG_2

4-Warning

EXCEPTION - %lu - Insufficient storage to send RTM statistics to host [chars]

Insufficient storage to send RTM statistics to host.\n\ RTM statistics displayed by host will be inconsistent.

snasw

-

SNASW-6-CS2_LOG_0

6-Information

INFO - %lu - Implicit link limit on port reached [chars]

An implicit dynamic or discovery link could not be activated\n\ because the implicit link limit defined on the port has been\n\ reached or exceeded.\n\ The link type being activated is:\n\ 1 - dynamic\n\ 3 - implicit\n\ 4 - discovery

snasw

"None"

SNASW-4-CS2_LOG_2

4-Warning

EXCEPTION - %lu - Link activation race detected - local node responsible for disconnect [chars]

A link activation race was detected on an ATM port. The local\n\ node is responsible for resolving this race.\n\ The local node will disconnect its link. The remote node's link\n\ activation request will succeed.

snasw

"This is a normal race condition - no action is required."

SNASW-4-CS2_LOG_3

4-Warning

EXCEPTION - %lu - Link activation race detected - adjacent node responsible for disconnect [chars]

A link activation race was detected on an ATM port. The remote\n\ node is responsible for resolving this race.\n\ The local node will send a negotiation error CV indicating that\n\ the remote link activation request should fail. The local\n\ node's link activation request will succeed.

snasw

"This is a normal race condition - no action is required."

SNASW-4-CS2_LOG_4

4-Warning

EXCEPTION - %lu - PORT_BANDWIDTH_UPDATE status = QUIESCING received [chars]

-

snasw

"If possible increase the bandwidth available to the local\n\ port."

SNASW-4-CS2_LOG_5

4-Warning

EXCEPTION - %lu - PORT_BANDWIDTH_UPDATE status = OK received [chars]

-

snasw

"To avoid future problems with bandwidth shortage increase\n\ the bandwidth available to the local port."

SNASW-3-CS2_LOG_9

3-Error

PROBLEM - %lu - DLC failure during creation [chars]

The DLC has returned inconsistent data during creation\n\ The DLC will be destroyed and all ports and link stations\n\ defined on the DLC will be inoperative.

snasw

"Run a trace on the DLC and contact support with the log and\n\ trace information."

SNASW-4-CS2_LOG_10

4-Warning

EXCEPTION - %lu - Link activation retry limit reached [chars]

An automatic retry link station is still inactive after the\n\ maximum allowed number of retries.\n\ The link station will remain inactive awaiting operator\n\ intervention. In the mean time the activation of any sessions\n\ relying on this link station will fail.

snasw

"Check surrounding logs for link activation failures. Check the\n\ configuration of the link station. Check the state of the\n\ adjacent node. Issue snasw start link to retry activation."

SNASW-4-CS2_LOG_11

4-Warning

EXCEPTION - %lu - A request to activate a connection network TG was rejected because the local and destination link addresses were incompatible [chars]

SNA Switch cannot start a link to an adjacent node over a\n\ connection network TG because the link address on the\n\ local node is not compatible with the link address on the\n\ adjacent node.\n\ The session will fail with the specified sense code.

snasw

"Check the local and destination link addresses."

SNASW-4-CS2_LOG_12

4-Warning

EXCEPTION - %lu - A request to activate a connection network TG was rejected because a defined link was already active between the local and destination address and multiple links are not supported [chars]

SNA Switch cannot start a link to an adjacent node over a\n\ connection network TG because the DLC does not support mutiple\n\ links between the local and destination addresses.\n\ The session will fail with the specified sense code.

snasw

"Check the local and destination link addresses."

SNASW-4-CS2_LOG_25

4-Warning

EXCEPTION - %lu - Insufficient resources to unregister adjacent LEN [chars]

-

snasw

"Ensure sufficient resources are available to SNA Switch and then\n\ re-cycle the link to the required state."

SNASW-4-CS2_LOG_26

4-Warning

EXCEPTION - %lu - Invalid TG descriptor received from DLUS [chars]

An invalid TG descriptor was received from a DLUS.\n\ The PU will not be activated.

snasw

"Check the configuration of the DLUS named by this log. Contact\n\ support with details of the problem."

SNASW-4-CS2_LOG_27

4-Warning

EXCEPTION - %lu - A DLUS-defined downstream DLUR-served link could not be defined [chars]

A DLUS-defined downstream DLUR-served link could not be defined\n\ because either:\n\ - the specified port does not exist\n\ - there is an existing link station to the same destination\n\ address.\n\ The PU will not be activated.

snasw

"Correct the configuration."

SNASW-4-CS2_LOG_28

4-Warning

EXCEPTION - %lu - A DLUS-defined downstream DLUR-served link failed to activate [chars]

A DLUS-defined downstream link failed to activate.\n\ The PU will not be activated.

snasw

"Check that the named port is active. Check that the downstream\n\ node at the given address is powered on. Check surrounding\n\ logs for reasons that the named LS has not activated. Check\n\ the configuration of the DLUS."

SNASW-4-CS2_LOG_29

4-Warning

EXCEPTION - %lu - DLUS-defined DSPU name clashes with locally-defined DSPU name [chars]

A DLUS-defined DSPU name clashes with the locally-defined DSPU\n\ name of a different PU.\n\ An implicit link will fail. The ACTPU for the DSPU connected\n\ over this link will be rejected.

snasw

"Reconfigure this node or the DLUS to remove the clash in the\n\ use of this PU name. If the DLUS and the DLUR use the same PU\n\ name then they must apply this name to the same PU."

SNASW-4-CS2_LOG_30

4-Warning

EXCEPTION - %lu - Insufficient information to create a DLUS-defined link to a DLUR DSPU [chars]

Insufficient information to create a DLUS-defined link.\n\ A PU will not be activated. The ACTPU for the named PU will\n\ be rejected with the given sense code.

snasw

-

SNASW-4-CH2_LOG_0

4-Warning

EXCEPTION - %lu - CRV exchange failed on a PLU-SLU session. The session will fail [chars]

CRV exchange failed. This indicates the cryptography keys\n\ configured at this LU and the partner LU are inconsistent.\n\ Session will be deactivated with the specified sense code\n\ 08350001.

snasw

-

SNASW-4-CH2_LOG_1

4-Warning

EXCEPTION - %lu - Protocol error during CRV exchange [chars]

Protocol error during CRV exchange. This indicates a possible\n\ interoperability problem. Sense codes are as follows.\n\ 20090000 - CRV request received from secondary LU or\n\ CRV response received from primary LU or\n\ CRV not received when expected\n\ 10020000 - CRV RU too short\n\ 400F0000 - CRV with FI not set\n\ 400B0000 - CRV chain indicators not set to BC EC\n\ 40140000 - CRV not RQD1\n\ 40110000 - CRV not expedited\n\ 40150000 - CRV with QRI not set\n\ 40080000 - CRV with PI set\n\ 400C0000 - CRV request with BBI EBI or CEBI set\n\ 400D0000 - CRV request with CDI set\n\ 40100000 - CRV request with CSI set to CODE1\n\ 40160000 - CRV request with EDI set\n\ 40170000 - CRV request with PDI set\n\ 40130000 - CRV response RTI and SDI inconsistent\n\ Session will be deactivated with specified sense code.

snasw

-

SNASW-4-CH2_LOG_2

4-Warning

EXCEPTION - %lu - Insufficient storage to initialise half session [chars]

Insufficient storage to initialise the half session.\n\ The half session will fail to activate with the specified sense\n\ code.

snasw

-

SNASW-4-SM2_LOG_0

4-Warning

EXCEPTION - %lu - Standard compression levels used [chars]

-

snasw

"None."

SNASW-4-SM2_LOG_1

4-Warning

EXCEPTION - %lu - Failed to adjust a buffer pool [chars]

The desired number of buffers could not be reserved for a\n\ buffer pool.\n\ The receive pacing window size for the session will not\n\ increase as fast as configured.

snasw

-

SNASW-4-LM2_LOG_0

4-Warning

EXCEPTION - %lu - CRV exchange failed on a PLU-SLU session. The session will fail. [chars]

CRV exchange failed. This indicates the cryptography keys\n\ configured at this LU and the partner LU are inconsistent.\n\ Session will be deactivated with the specified sense code\n\ 08350001.

snasw

"Correct the mismatch in cryptography keys."

SNASW-4-LM2_LOG_1

4-Warning

EXCEPTION - %lu - A conventional half-session has aborted. [chars]

Critical buffer shortage or protocol error or CRV exchange\n\ protocol error. This indicates a possible interoperability\n\ problem. Sense codes for CRV exchange errors are as follows.\n\\n\ 20090000 - CRV request received from secondary LU or\n\ CRV response received from primary LU or\n\ CRV not received when expected\n\ 10020000 - CRV RU too short\n\ 400F0000 - CRV with FI not set\n\ 400B0000 - CRV chain indicators not set to BC EC\n\ 40140000 - CRV not RQD1\n\ 40110000 - CRV not expedited\n\ 40150000 - CRV with QRI not set\n\ 40080000 - CRV with PI set\n\ 400C0000 - CRV request with BBI EBI or CEBI set\n\ 400D0000 - CRV request with CDI set\n\ 40100000 - CRV request with CSI set to CODE1\n\ 40160000 - CRV request with EDI set\n\ 40170000 - CRV request with PDI set\n\ 40130000 - CRV response RTI and SDI inconsistent\n\\n\ Session will be deactivated with specified sense code.

snasw

"If surrounding logs indicate critical congestion decrease the\n\ system load or make more resources available to SNA Switch.\n\ Otherwise contact support with details of the problem."

SNASW-4-RTP2_LOG_0

4-Warning

EXCEPTION - %lu - RTP Connection is path-switching to a much longer path [chars]

An RTP connection is path-switching to a much longer path than\n\ it started with. Much more room is needed in each packet for\n\ routing information than was originally planned.\n\ Performance across this RTP connection may degrade since some\n\ packets may have to be segmented.

snasw

"If performance degradation is noticed reactivate failed links\n\ then issue the 'PATH_SWITCH' verb."

SNASW-4-RTP2_LOG_1

4-Warning

EXCEPTION - %lu - Invalid ARB support received from remote node [chars]

A value for ARB support that the local node does not support\n\ has been received in an ARB setup segment. The remote node\n\ has not completed the ARB negotiation correctly. This\n\ is a protocol error.\n\ The connection will be deactivated.

snasw

"Investigate the cause of the error at the adjacent node."

SNASW-4-DS2_LOG_0

4-Warning

EXCEPTION - %lu - Insufficient resources to unregister adjacent LEN [chars]

-

snasw

"Ensure sufficient resources are available to SNA Switch and then\n\ re-cycle the link to the required state."

SNASW-3-DS2_LOG_1

3-Error

PROBLEM - %lu - Inaccurate directory entry held for this LU [chars]

A directed locate for this LU has been tried but the LU was\n\ not recognised at the end node stored in the directory.\n\ The directory entry is removed and a broadcast locate is sent\n\ instead.

snasw

"None."

SNASW-4-DS2_LOG_2

4-Warning

EXCEPTION - %lu - Failed to register resource with NNS/CDS [chars]

Failed to allocate memory for storage of resource in the\n\ register list.\n\ Registration will not take place immediately.

snasw

"None."

SNASW-4-DS2_LOG_3

4-Warning

EXCEPTION - %lu - Received a Locate reply with an invalid RSCV [chars]

A locate reply was received that contained an invalid RSCV.\n\ The locate request that solicited the reply may be failed.

snasw

"Contact support with details of the problem."

SNASW-4-DS2_LOG_4

4-Warning

EXCEPTION - %lu - Insufficient resources to register adjacent LEN LU [chars]

Branch Network node has insufficient resources to register\n\ an adjacent LEN node's LU\n\ The directory of this node and/or that of its NNS may become\n\ inconsistent in that the LEN LU will not be registered when\n\ it should be. Thus session activation to the LEN LU may fail\n\ when a link to it is active

snasw

"Ensure sufficient resources are available to SNA Switch and then\n\ re-cycle the link to the required state."

SNASW-3-DS2_LOG_5

3-Error

PROBLEM - %lu - LEN LU registration failed because the LU name is already registered as the child of a different CP [chars]

Node is configured to register LEN LU names when BINDs from\n\ LEN nodes are passed through us. In this case registration\n\ failed due to a resource name conflict. The LU name is already\n\ registered as the child of a different CP.\n\ Registration of the resource in question will fail so sessions\n\ to the LEN LU cannot be started except by the LEN itself.\n\ Other resources should still be registered correctly.

snasw

"Check the network node's directory for the duplicate entry. If\n\ it is a home entry then remove the home entry from the\n\ directory. If it is a registered entry owned by a different\n\ end node redefine the LU to use a different name."

SNASW-4-DS2_LOG_6

4-Warning

EXCEPTION - %lu - Duplicate FQPCID prevents start of network search [chars]

A LOCATE message received with duplicate PCID. This could\n\ occur if two LEN nodes send BINDs to SNA Switch at the same\n\ time and with the same PCID. Session activation will fail\n\ with the specified sense code.

snasw

"None. The downstream box should retry the session activation\n\ using a different PCID."

SNASW-4-DS2_LOG_7

4-Warning

EXCEPTION - %lu - Adjacent node registered an Associated Resource which was not an ENCP [chars]

The local node is a Branch Network Node or Network Node and a\n\ downstream node registered an Associated Resource that was not\n\ an ENCP resource.

snasw

"None the node will force the resource type to be ENCP."

SNASW-3-RM2_LOG_0

3-Error

PROBLEM - %lu - CP-CP session deactivated because of excessive delay [chars]

An adjacent node has not responded within a reasonable period\n\ to a request on a CP-CP session. SNA Switch will deactivate\n\ CP-CP sessions with this adjacent node.\n\ CP-CP sessions are deactivated with the sense code 08640002.

snasw

"Contact the supplier of the adjacent node."

SNASW-6-LDLC_DEBUG_LOG_0

6-Information

INFO - %lu - Link activation race has occurred [chars]

Link activation race has occurred\n\ Link activation will complete but the routes may be different\n\ in each direction. No other effect will be noticeable.

snasw

"None."

SNASW-4-LDLC_CTRL_LOG_0

4-Warning

EXCEPTION - %lu - Unable to create a new LDLC_CTRL instance [chars]

Unable to create a new LDLC_CTRL instance.\n\ Link activation cannot continue. This will result in the\n\ failure of an outbound link activation attempt or the rejection\n\ of an inbound link activation.

snasw

"Check surrounding logs for evidence of buffer congestion. If\n\ buffer congestion is causing this failure either decrease the\n\ system load or make more resources available to LDLC."

SNASW-4-LDLC_CTRL_LOG_1

4-Warning

EXCEPTION - %lu - LDLC command frame retry limit exceeded [chars]

LDLC command frame retry limit exceeded.\n\ Link activation will fail or an active link will be brought\n\ down.

snasw

"Check connectivity to remote address"

SNASW-4-LDLC_CTRL_LOG_2

4-Warning

EXCEPTION - %lu - LDLC link reported inoperative by underlying media [chars]

LDLC link reported inoperative by underlying media.\n\ Link activation will fail or an active link will be brought\n\ down.

snasw

"Check for faults at the supplied destination address. Check\n\ for faults and error conditions in the underlying drivers and\n\ media. Check for connectivity in the underlying media. Check\n\ for outages on the connection path. Check all your wires are\n\ still plugged in."

SNASW-4-LDLC_DATA_LOG_0

4-Warning

EXCEPTION - %lu - Unrecognised NHDR routing instruction [chars]

Unrecognised NHDR routing instruction.\n\ This packet cannot be routed by LDLC and will be discarded.\n\ Data may be lost. This may indicate an interoperability\n\ problem.

snasw

"Check surrounding logs for other evidence of interoperability\n\ problems. If failures or problems occur gather trace of the\n\ protocol flows then report this problem to support."

SNASW-4-LDLC_DATA_LOG_1

4-Warning

EXCEPTION - %lu - Unrecognised LDLC RU identifier [chars]

Unrecognised LDLC RU identifier.\n\ This packet cannot be processed by LDLC and will be discarded.\n\ Link activation may fail. Link deactivation may fail. Data\n\ may be lost. This may indicate an interoperability problem.

snasw

"Check surrounding logs for other evidence of interoperability\n\ problems. If failures or problems occur gather trace of the\n\ protocol flows then report this problem to support."

SNASW-4-LDLC_DATA_LOG_2

4-Warning

EXCEPTION - %lu - Unable to grant credit [chars]

Unable to grant credit\n\ LDLC is unable to grant further send credit.

snasw

"Check surrounding logs for evidence of buffer congestion. If\n\ buffer congestion is causing this failure either decrease the\n\ system load or make more resources available to LDLC."

SNASW-4-LDLC_IP_LOG_0

4-Warning

EXCEPTION - %lu - IPDLC failed to allocate necessary storage [chars]

IPDLC could not allocate necessary storage.\n\ Some operation may fail. See other logs.

snasw

-

SNASW-4-LDLC_IP_LOG_1

4-Warning

EXCEPTION - %lu - IPDLC failed to request a posting [chars]

IPDLC failed to request a posting.\n\ Link activation may fail or data transmission may be delayed.

snasw

-

SNASW-4-LDLC_IP_LOG_2

4-Warning

EXCEPTION - %lu - IPDLC failed to grow a link hash table [chars]

IPDLC failed to grow a link hash table.\n\ Data transmission rates may be marginally degraded.

snasw

-

SNASW-4-LDLC_IP_LOG_3

4-Warning

EXCEPTION - %lu - IPDLC failed to create a UDP stub [chars]

IPDLC failed to create a UDP stub.\n\ Port activation will fail.

snasw

-

SNASW-4-LDLC_IP_LOG_4

4-Warning

EXCEPTION - %lu - IPDLC's UDP stub has failed to initialise [chars]

IPDLC has created a UDP stub but the UDP stub failed to\n\ initialise successfully.\n\ Port activation will fail.

snasw

" Check surrounding logs and other diagnostics for reports of a\n\ failure from a UDP stub process."

SNASW-6-LDLC_IP_LOG_9

6-Information

INFO - %lu - Invalid IP address specified for a IPDLC link [chars]

Invalid IP address specified for a IPDLC link.\n\ The link will fail to start.

snasw

" Correct the configuration. These settings are supplied in the\n\ address information passed to SNA Switch on snasw link."

SNASW-4-LDLC_IP_LOG_10

4-Warning

EXCEPTION - %lu - Unable to activate IPDLC port [chars]

Unable to activate an IPDLC port.\n\ This will result in the failure of a port activation attempt.\n\ No further IPDLC operation will be possible until a port is\n\ activated successfully.

snasw

" - Check surrounding logs for evidence of buffer congestion.\n\ If buffer congestion is causing this failure either\n\ decrease system load or make more resources available to\n\ IPDLC.\n\ - Ensure that the necessary facilities are available for the\n\ UDP interface to operate correctly.\n\ - Check that valid DLC specific configuration data was\n\ provided to IPDLC at define time."

SNASW-4-LDLC_IP_LOG_11

4-Warning

EXCEPTION - %lu - Unable to activate IPDLC link [chars]

Unable to activate an IPDLC link.\n\ Link activation cannot continue. This will result in the\n\ failure of an outbound link activation attempt or the\n\ rejection of an inbound link activation.

snasw

" - Check surrounding logs for evidence of buffer congestion.\n\ If buffer congestion is causing this failure either\n\ decrease system load or make more resources available to\n\ IPDLC.\n\ - Ensure that the necessary facilities are available for the\n\ UDP interface to operate correctly.\n\ - Check that valid DLC specific configuration data was\n\ provided to SNAP-IPDLC at define time."

SNASW-3-LDLC_IP_LOG_12

3-Error

PROBLEM - %lu - The IPDLC UDP stub process has abended - SNAP IPDLC will abend [chars]

The UDP stub process has abended.\n\ IPDLC will abend itself. All links using SNAP-IPDLC will\n\ fail. SNAP-IPDLC will fail.

snasw

" Check for the UDP/IP problem that caused the UDP stub to\n\ abend. If the reason cannot be determined gather full trace\n\ and contact support."

SNASW-4-TNTL_LOG_0

4-Warning

EXCEPTION - %lu - Implicit alias space wrapped [chars]

The space for implicit aliases has wrapped. There is a very\n\ slight possibility of duplicate aliases.

snasw

"Shut down and restart to avoid any conflict."

SNASW-3-TNTL_LOG_1

3-Error

PROBLEM - %lu - Invalid internal state detected [chars]

A software error has caused a bad internal state to be\n\ detected. Potential loss of function - refer to other problem logs for\n\ actual effect.

snasw

"Shut down and restart"

SNASW-4-TNBM_LOG_0

4-Warning

EXCEPTION - %lu - The Buffer Manager Monitor could not allocate necessary resource [chars]

The Buffer Manager Monitor could not allocate necessary\n\ resource.\n\ The Buffer Manager will fail to operate and detect congestion\n\ conditions or relief from congestion possibly leading to the\n\ node locking up.

snasw

"Shutdown and restart the node."

SNASW-4-TNBM_LOG_1

4-Warning

EXCEPTION - %lu - Insufficient storage to create new buffer pool [chars]

-

snasw

"Investigate memory shortage and system load."

SNASW-4-TNBM_LOG_2

4-Warning

EXCEPTION - %lu - Insufficient buffers to create new buffer pool [chars]

-

snasw

"Investigate buffer shortage and system load."

SNASW-4-TNBM_LOG_3

4-Warning

EXCEPTION - %lu - Critical buffer congestion [chars]

The Buffer Manager Monitor detected critical buffer congestion\n\ SNA Switch will throttle back session traffic by withholding\n\ pacing responses or resetting pacing windows on adaptive-paced\n\ sessions until the congestion has reduced.

snasw

"This condition can occur if the node receives a\n\ large sudden burst of data traffic on several sessions. The\n\ condition should clear itself automatically but if it occurs\n\ frequently it may indicate the node is routing more sessions\n\ than it can handle efficiently with the available buffer\n\ storage. Reduce the number of sessions through the router."

SNASW-4-TNBM_LOG_4

4-Warning

EXCEPTION - %lu - Buffer congestion relieved [chars]

Buffer congestion relieved. SNA Switch will stop throttling\n\ back session traffic. If the congestion eases further SNA\n\ Switch will start to increase pacing windows on adaptively\n\ paced sessions.

snasw

"None"

SNASW-4-TNBM_LOG_5

4-Warning

EXCEPTION - %lu - Critical buffer congestion detected while attempting to relieve congestion [chars]

The Buffer Manager detected critical buffer congestion while\n\ attempting to relieve a previous congestion condition.\n\ SNA Switch will throttle back session traffic by withholding\n\ pacing responses or resetting pacing windows on adaptive-paced\n\ sessions until the congestion has reduced.

snasw

"This condition can occur if the node receives a\n\ large sudden burst of data traffic on several sessions. The\n\ condition should clear itself automatically but if it occurs\n\ frequently it may indicate the node is routing more sessions\n\ than it can handle efficiently with the available buffer\n\ storage. Reduce the number of sessions through the router."

SNASW-4-TNBM_LOG_6

4-Warning

EXCEPTION - %lu - Insufficient storage to request posting [chars]

Insufficient storage to request posting\n\ The component using the Buffer Manager may fail to operate\n\ or lock up. See other logs for effects.

snasw

"Investigate memory shortage and system load."

SNASW-3-CLSIBadPrimitive

3-Error

CLSI bad primitive type header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-CLSIFailure

3-Error

SNASW failed to process CLSI message header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-DLCFailure

3-Error

SNASW failed to process DLC message header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-DLCBadMessage

3-Error

DLC unrecognized message header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-CLSIBadReturnCode

3-Error

CLSI bad return code: [dec] header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-DLCInvalidFsmState

3-Error

Invalid Input=[chars] to SNASW [chars] [hec] with OldState=[chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-DLCPortFailure

3-Error

Port [chars] activation failed: [chars]

An error was received from CLS. Typically indicates a configuration error.

-

LOG_STD_RECUR_ACTION

SNASW-3-MIBQueryFailure

3-Error

Query [chars] failed. NOF primary rc=[hec] secondary rc=[hec].

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-MIBRegisterFailure

3-Error

[chars] Indication [hec] failed. NOF primary rc=[hec] secondary rc=[hec].

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-3-MIBTrapFailure

3-Error

Trap failed. [chars] MIB OID=[chars] index OID=[chars].

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SNASW-4-CPUUsage

4-Warning

SNASw process type 0x[hec] ran for %lu ms processing IPS of type 0x[hec] address 0x%lx

A process within SNA Switch ran for an unexpectedly\n\ long time.

-

LOG_STD_RECUR_ACTION

DNET-4-MAPCON

4-Warning

Map entry [dec].[dec] conflicts with adjacency to [dec].[dec]

Your DECnet configuration is incorrect. A host that is specified as\n\ nonlocal is present on your local network.

-

"Correct the configuration. Call your technical support representative\n\ if you need assistance."

DNET-3-HEARSELF

3-Error

Hello type [hec] for my address from [dec].[dec] via [chars]

The system is receiving its own DECnet packets. Either a serial line\n\ is looped back or another host with the same DECnet address is already\n\ present on the LAN.

-

"Check the serial lines if present and the DECnet configuration."

DNET-3-NOMEMORY

3-Error

Insufficient memory for DECnet accounting entry

The traffic information for a particular pair of DECnet nodes \n\ cannot be recorded due to a low memory condition.

decnet

LOG_STD_REDUCE_ACTION

DNET-4-DUPENTRY

4-Warning

Duplicate DECnet Accounting List Entry for nodes [dec].[dec] - [dec].[dec]

A synchronization problem has occurred whilst a new transit \n\ DECnet Accounting List Entry was being added and a duplicate entry\n\ has been found.

decnet

show decnet accounting

MONITOR-3-VARSETFAIL

3-Error

ROM monitor variable set of \[chars]\ failed.

The system could not set a ROM Monitor variable. This condition\n\ typically occurs when no ROM monitor memory is available to save\n\ the variable. The ROM monitor memory is most likely already filled\n\ with configuration <CmdBold>boot<NoCmdBold> commands.

high-rommon

"Enter the <CmdBold>show bootvar<NoCmdBold> command and\n\ check the output to see if there is anything unusual with the system.\n\ Try to reduce the number of configuration boot commands."

MONITOR-3-VARRESTFAIL

3-Error

ROM monitor variable restoration of \[chars]\ failed.

The new ROM monitor variable could not be written to memory and the\n\ ROM monitor variable could not be restored to its original value.

high-rommon

"Copy the error message exactly as it appears on the console or in the\n\ system log. Issue the <CmdBold>show tech-support<NoCmdBold> and\n\ <CmdBold>show bootvar<NoCmdBold> commands to gather data that may help\n\ identify the nature of the error. If you cannot determine the nature\n\ of the error from the error message text or from the <CmdBold>show\n\ tech-support<NoCmdBold> and <CmdBold>show bootvar<NoCmdBold> command\n\ output contact your Cisco technical support representative and\n\ provide the representative with the gathered information."

DC-4-FILE_OPEN_WARNING

4-Warning

Not able to open [chars]

The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles.

dc

" Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. "

DC-3-PATTERN_NOT_FOUND

3-Error

[chars]

The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reload the Device Profiles file to the flash and re-enable the device classifier"

DC-3-INCOMPATIBLE_PROFILE_VERSION

3-Error

Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec]

An incompatible profile version is detected. The device classifier feature will be operationally down.

dc

"Reload the expected version of device profiles file to the " "system and re-enable the device classifier "

DC-3-BUILTIN_INIT_FAIL

3-Error

[chars]

Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-6-DEFAULT_INIT_INFO

6-Information

[chars]

The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles.

dc

LOG_STD_ACTION

DC-3-SM_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Registraton of Device classifier with SM failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-OUI_INIT_FAIL

3-Error

OUI Table initialization failed for [chars]

Loading of the OUI databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-CHECK_INIT_FAIL

3-Error

[chars]

Loading of the Checks databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-DB_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Initilization of Device classifier Internal database failed So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-MAX_RULES_EXCEEDED

3-Error

[chars].

The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_PROFILES_EXCEEDED

3-Error

[chars].

The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_OUI_EXCEEDED

3-Error

[chars].

The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-NO_MEM

3-Error

[chars].

There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Increase the memory size in the system and " "re-enable the device classifier"

DC-3-DC_DISABLED

3-Error

[chars].

The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles

dc

"The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier"

DC-3-SM_UPDATE

3-Error

Failed to update [chars].

Internal error occured during device classification . This may cause the device to be unknown.

dc

-

DC-3-SM_API

3-Error

[chars] return [chars].

Internal error returned by Session Manager api.

dc

-

DC-3-FILE_READ_ERROR

3-Error

Error [chars] the profile file: [chars]

There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-FILE_CHECKSUM

3-Error

Checksum [chars] failed for the profile file: [chars]

Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-SM_GET

3-Error

Failed to get [chars].

Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results.

dc

-

DC-3-DISABLE_FAIL

3-Error

Failed to disable DC.

Internal error occured trying to disable Device Classifier.

dc

"Please run the command: show macro auto monitor clients and try disabling" "the clients"

DC-3-ENABLE_FAIL

3-Error

Failed to enable DC.

Internal error occured trying to enable Device Classifier.

dc

"Please check the previous DC error messages and take the relevant action"

DC-3-HRPC_SYNC

3-Error

Error on member switch [dec] error_code = [dec]

Internal error occured while trying to sync Device Classifier.state

dc

"Please check the state of the stack members"

DC-4-FILE_OPEN_WARNING

4-Warning

Not able to open [chars]

The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles.

dc

" Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. "

DC-3-PATTERN_NOT_FOUND

3-Error

[chars]

The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reload the Device Profiles file to the flash and re-enable the device classifier"

DC-3-INCOMPATIBLE_PROFILE_VERSION

3-Error

Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec]

An incompatible profile version is detected. The device classifier feature will be operationally down.

dc

"Reload the expected version of device profiles file to the " "system and re-enable the device classifier "

DC-3-BUILTIN_INIT_FAIL

3-Error

[chars]

Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-6-DEFAULT_INIT_INFO

6-Information

[chars]

The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles.

dc

LOG_STD_ACTION

DC-3-SM_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Registraton of Device classifier with SM failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-OUI_INIT_FAIL

3-Error

OUI Table initialization failed for [chars]

Loading of the OUI databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-CHECK_INIT_FAIL

3-Error

[chars]

Loading of the Checks databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-DB_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Initilization of Device classifier Internal database failed So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-MAX_RULES_EXCEEDED

3-Error

[chars].

The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_PROFILES_EXCEEDED

3-Error

[chars].

The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_OUI_EXCEEDED

3-Error

[chars].

The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-NO_MEM

3-Error

[chars].

There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Increase the memory size in the system and " "re-enable the device classifier"

DC-3-DC_DISABLED

3-Error

[chars].

The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles

dc

"The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier"

DC-3-SM_UPDATE

3-Error

Failed to update [chars].

Internal error occured during device classification . This may cause the device to be unknown.

dc

-

DC-3-SM_API

3-Error

[chars] return [chars].

Internal error returned by Session Manager api.

dc

-

DC-3-FILE_READ_ERROR

3-Error

Error [chars] the profile file: [chars]

There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-FILE_CHECKSUM

3-Error

Checksum [chars] failed for the profile file: [chars]

Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-SM_GET

3-Error

Failed to get [chars].

Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results.

dc

-

DC-3-DISABLE_FAIL

3-Error

Failed to disable DC.

Internal error occured trying to disable Device Classifier.

dc

"Please run the command: show macro auto monitor clients and try disabling" "the clients"

DC-3-ENABLE_FAIL

3-Error

Failed to enable DC.

Internal error occured trying to enable Device Classifier.

dc

"Please check the previous DC error messages and take the relevant action"

DC-3-HRPC_SYNC

3-Error

Error on member switch [dec] error_code = [dec]

Internal error occured while trying to sync Device Classifier.state

dc

"Please check the state of the stack members"

CARRIER-3-PLATFORM_DFC

3-Error

DFC Carrier Platform Init Failed - Slot [dec]

DFC Carrier Platform Init Failed

as

LOG_STD_ACTION

CARRIER-3-POWER_DFC

3-Error

DFC Power-On Failed - DFC [dec]

DFC Power-On Failed

as

LOG_STD_ACTION

CARRIER-3-INVALID_DFC

3-Error

Invalid DFC - DFC [dec] type [dec]

DFC has invalid board id/type

as

LOG_STD_ACTION

CARRIER-2-THREE_NP108_NOT_PRESENT

2-Critical

3 NP108s were not found on Tetryl card [dec] detected.

Tetryl requires 3 NP108s to be present

tetryl

LOG_STD_ACTION

CARRIER-3-RESET_DFC

3-Error

DFC Reset Failed - DFC [dec]

During OIR Removal process DFC reset failed.

as

LOG_STD_ACTION

CARRIER-3-DFC_POWER_INT

3-Error

DFC Power Changed - DFC [dec]

DFC Power is fluctuating

as

LOG_STD_ACTION

CARRIER-3-DFC_INIT_ALREADY

3-Error

DFC is already initialized - DFC [dec]

DFC is already initialized no need to initialize again

as

LOG_STD_ACTION

CARRIER-3-DFC_INIT_FAIL

3-Error

DFC initialization is failed - DFC [dec]

DFC initialization is failed because of several reasons

as

LOG_STD_ACTION

CARRIER-2-T1_E1_MIX

2-Critical

Cannot mix T1 and E1 8PRI DFC cards in chassis\ do not power up invalid card in slot [dec]\n

The user has put T1 and E1 8PRI DFC cards in the same chassis.

-

"Remove the extra T1 or E1 8PRI DFC card."

CARRIER-2-TOOMANY_CT3

2-Critical

Too many CT3 DFC cards do not power up invalid card in slot [dec]\n

The user has put too many CT3 DFC cards in the chassis.

-

"Remove the extra CT3 DFC card or 8PRI DFC card causing problem"

CARRIER-2-TOOMANY_8PRI

2-Critical

Too many 8PRI DFC cards do not power up invalid card in slot [dec]\n

The user has put too many 8PRI DFC cards in the chassis.

-

"Remove the extra 8PRI DFC card."

CARRIER-2-TOOMANY_TRUNK

2-Critical

Too many trunk DFC cards do not power up invalid card in slot [dec]\n

The user has put too many trunk DFC cards in the chassis.

-

"Remove the extra trunk DFC card."

CARRIER-2-CT3_E1_MIX

2-Critical

Cannot mix E1 PRI and CT3 DFC in chassis\ do not power up invalid card in slot [dec]\n

The user has put E1 PRI and CT3 DFC cards in the same chassis.

-

"Remove the extra E1 PRI or CT3 DFC card."

DFP-4-UKN_CON

4-Warning

Manager [inet] Service [chars] - Unknown connection state [dec]

Unknown connection state processing DFP timer

dfp

LOG_STD_RECUR_ACTION

DFP-4-BAD_SEND

4-Warning

Manager [inet]:[dec] - Send failed

Sending a message to DFP Manager failed

dfp

LOG_STD_RECUR_ACTION

DFP-4-SOCK_ERR

4-Warning

Manager [inet]: Service [chars] - Socket_recv error [dec]

Socket_recv error receiving message from DFP Manager

dfp

LOG_STD_RECUR_ACTION

DFP-4-READ_ERR

4-Warning

Manager [inet]: Service [chars] - Too many read errors

Too many errors reading message header from DFP Manager

dfp

LOG_STD_RECUR_ACTION

DFP-4-NO_PARSE

4-Warning

Manager [inet]: Service [chars] - Could not parse message

Could not parse message from DFP Manager

dfp

LOG_STD_RECUR_ACTION

DFP-4-UNK_TYPE

4-Warning

Manager [inet]: Service [chars] - Unknown message type [dec]

Message from DFP Manager has unknown type

dfp

LOG_STD_RECUR_ACTION

DFP-4-ENQUEUE

4-Warning

Process enqueue failed: [chars]

An unexpected error occurred while enqueueing a DFP element

dfp

LOG_STD_RECUR_ACTION

DFP-4-BAD_POINTER

4-Warning

[chars] Application did not set pointer

Application passed invalid pointer to DFP subsystem

dfp

LOG_STD_RECUR_ACTION

DFP-4-NUM_TOO_LARGE

4-Warning

[chars] Application sent too many values

Application sent too many values to DFP subsystem

dfp

LOG_STD_RECUR_ACTION

DFP-4-AGENT_NOT_FOUND

4-Warning

[chars] Service has not been registered with DFP.

No such service registered with DFP subystem.

dfp

LOG_STD_RECUR_ACTION

DFP-4-BAD_LISTEN

4-Warning

Service [chars] - Listen failed

Listen for DFP Manager failed.

dfp

LOG_STD_RECUR_ACTION

DFP-4-NO_PROCESS_START

4-Warning

Could not start process for service [chars]

Could not start DFP Process for service [chars]

dfp

LOG_STD_RECUR_ACTION

DFP-4-STRING_TOO_LONG

4-Warning

The string [chars] exceeds 15 characters - too long for service name.

The user input a service string that exceeds 15 characters

dfp

LOG_STD_RECUR_ACTION

DFP-4-PACKET_TOO_SMALL

4-Warning

The DFP packet is too small from manager [inet] service [chars].

A DFP packet has been received that is too small.

dfp

LOG_STD_RECUR_ACTION

DFP-4-REPEAT_SERVICE_INIT

4-Warning

Service [chars] is already intialized cannot re-initialize

The application has atempted to re-initialize a service

dfp

LOG_STD_RECUR_ACTION

DFP-4-NO_QUEUE_REQUEST

4-Warning

Could not queue request for [chars] for service [chars]

Could not queue request to the DFP process for specific action

dfp

LOG_STD_RECUR_ACTION

DFP-4-SUBSYS_NOT_UP

4-Warning

Service [chars] - attempted to register before DFP Subsytem is up.

Problem with order of subsystem initialization.

dfp

LOG_STD_RECUR_ACTION

DFP-4-SECURITY_FAIL

4-Warning

[chars] security information in CASA packet from manager [inet] service [chars].

Security check failed.

casa

"Make sure all CASA/DFP systems are configured with the same password."

DFP-4-BIND_FAIL

4-Warning

Failure binding port [dec] to socket for service [chars].

Problem with call to socket bind.

dfp

LOG_STD_RECUR_ACTION

DHCP-6-ADDRESS_ASSIGN

6-Information

Interface [chars] assigned DHCP address [inet] mask [inet] hostname [chars]\n

The interface has been allocated an address via DHCP

-

"This is an informational message. No action is required"

DHCP-5-RESTART

5-Notice

Interface [chars] is being restarted by DHCP\n

DHCP is restarting the interface.

dhcp

LOG_STD_NO_ACTION

DHCP-3-HA_INIT_FAIL

3-Error

Function [chars] in DHCP client failed to initialize: [chars]\n

A high availability related function in the DHCP client failed to initialize properly. If you are using a platform with a redundant processor or box-to-box redundancy DHCP client settings may fail to be preserved if the main processor fails forcing use of the standby.

dhcp

"Please contact the TAC for assistance."

DHCPD-2-NO_PROCESS

2-Critical

DHCP could not start its [chars] process.

DHCP could not start one of its processes.

-

"Add more memory."

DHCPD-2-SOCKET_ERROR

2-Critical

DHCP could not open UDP port [dec].

DHCP could not open UDP port 67 bootps.

-

"Check if another application is using UDP port 67. If the port is\n\ available add more memory."

DHCPD-2-MALLOC_ERROR

2-Critical

There is inadequate memory for DHCP services.

DHCP could not allocate mandatory data structures.

-

"Add more memory."

DHCPD-2-RECVMSG_ERROR

2-Critical

Recvmsg failed unexpectedly. DHCP services have been terminated.

Reason for failure is unknown.

dhcp-server

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DHCPD-4-RELAY_ONLY

4-Warning

DHCP will run as a relay agent only.

DHCP could not start its database process. The server component has \n\ been disabled. Only the relay agent is active.

-

"Add more memory."

DHCPD-3-READ_ERROR

3-Error

DHCP could not read bindings from [chars].

The DHCP server could not read bindings from the specified database \n\ agent.

-

"Verify that the URL is correct and connectivity exists between the \n\ server and database agent. Check for a corrupt database file. The\n\ file must contain the *time* and *end* keywords. Execute the command \n\ \"show ip dhcp database.\" If there are aborted file transfers increase \n\ the database transfer timeout."

DHCPD-2-READ_DEADLOCK

2-Critical

DHCP has detected a deadlock condition excessive read failures.

The DHCP server could not read bindings from any database agent. All\n\ read attempts have failed. To prevent a possible deadlock the server\n\ has made all pool addresses available for assignment.

-

"Verify that all URLs are correct and connectivity exists between the \n\ server and all database agents. Check for corrupt database files. All\n\ files must contain the *time* and *end* keywords. Execute the command \n\ \"show ip dhcp database.\" If there are aborted file transfers increase \n\ the appropriate timeouts. Restart the DHCP server."

DHCPD-3-WRITE_ERROR

3-Error

DHCP could not write bindings to [chars].

The DHCP server could not write bindings to the specified database \n\ agent.

-

"Verify that the URL is correct and connectivity exists between the \n\ server and database agent. Execute the command \"show ip dhcp database.\"\n\ If there are aborted file transfers increase the database transfer \n\ timeout."

DHCPD-4-PING_CONFLICT

4-Warning

DHCP address conflict: server pinged %I.

The DHCP server has detected an address conflict. Another host is using\n\ the specified IP address. After resolving the conflict execute the\n\ command \clear ip dhcp conflict.\

-

"Resolve the misconfiguration. Clear the conflict from the DHCP \n\ database."

DHCPD-4-DECLINE_CONFLICT

4-Warning

DHCP address conflict: client [chars] declined %I.

The DHCP client has detected an address conflict. Another host is using\n\ the specified IP address. After resolving the conflict execute the\n\ command \clear ip dhcp conflict.\

-

"Resolve the misconfiguration. Clear the conflict from the DHCP \n\ database."

DHCPD-4-HA_CONFIG_MISMATCH

4-Warning

DHCP pool [chars] configuration on Active is not matched on the Standby.

Reason for failure is unknown.

dhcp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DHCPD-6-HIGH_UTIL

6-Information

Pool \[chars]\ is in high utilization state [dec] addresses used out of [dec]. Threshold set at [dec]%%.

The pool's utilization has exceeded the user configured high watermark.

dhcp

"Examine the DHCP pool and determine if the pool needs more IP addresses" " than currently allocated."

DHCPD-6-LOW_UTIL

6-Information

Pool \[chars]\ is in low utilization state [dec] addresses used out of [dec]. Threshold set at [dec]%%.

The pool's utilization has fallen below the user configured high watermark.

dhcp

"Examine the DHCP pool and determine if the pool needs more IP addresses" " than currently allocated."

DHCPD-6-MALFORMED_OPTION

6-Information

Invalid option [dec] message type [dec] received from client [chars]\n

DHCP client sent malformed option.

dhcp

"Check if DHCP client can be configured to send valid option."

DHCPD-3-HA_INIT_FAIL

3-Error

Function [chars] in DHCP server failed to initialize: [chars]\n

A high availability related function in the DHCP server failed to initialize properly. If you are using a platform with a redundant processor or box-to-box redundancy DHCP server data may fail to be preserved if the main processor fails forcing use of the standby.

dhcp

"Please contact the TAC for assistance."

DHCPD-3-NO_AAA_CONTEXT

3-Error

AAA configured but no AAA context in [chars]\n

DHCP is attempting to use AAA to grant a DHCP lease but no AAA context is associated with the binding

dhcp

"Please contact the TAC for assistance."

DHCPV6R-3-INVALID_USR_SRCADDR

3-Error

Invalid user specified source-address %P idb [chars] in ipv6 dhcp relay CLI.\n Removing user specified invalid address from the CLI and auto-computing source with SAS.

Invalid source-address has been provisioned in the ipv6 relay destination CLI.

dhcp

LOG_STD_REDUCE_ACTION

DHCPV6R-3-INVALID_USR_LINKADDR

3-Error

Invalid user specified link-address %P idb [chars] in ipv6 dhcp relay CLI.\n Removing user specified invalid address from the CLI.

Invalid link-address has been provisioned in the ipv6 relay destination CLI.

dhcp

LOG_STD_REDUCE_ACTION

DHCPV6C-3-NOSOCKET

3-Error

Cannot create DHCPv6 client socket

Most likely no IP enabled on any interface or a resource problem within the system.

dhcp

LOG_STD_REDUCE_ACTION

DHCPV6C-3-NOPACKET

3-Error

Cannot setup or duplicate a socket packet

Most likely a resource problem within the system.

dhcp

LOG_STD_REDUCE_ACTION

DHCPV6C-4-ZEROXID

4-Warning

Calculated DHCPv6 Lease Query xid is zero. Nothing is wrong just drop the LQv6 msg

After multiple tries the generated LQv6 msg xid is zero by accident. Just drop the LQv6 msg.

dhcp

LOG_STD_REDUCE_ACTION

DHCPV6S-3-NOPACKET

3-Error

Cannot setup or duplicate a DHCPv6 server socket packet

Most likely a resource problem within the system.

dhcp

LOG_STD_REDUCE_ACTION

DHCPV6S-3-DBNOTLOADED

3-Error

Binding database not loaded

Fail to load the DHCPv6 binding database.

dhcp

LOG_STD_ACTION

DHCPV6S-3-DBOPEN

3-Error

Openning [chars]: [chars]

Fail to open a DHCPv6 binding database file.

dhcp

LOG_STD_ACTION

DHCPV6S-3-DBWRITE

3-Error

Writing file: [chars]

Fail to write a DHCPv6 binding database file.

dhcp

LOG_STD_ACTION

DHCPV6S-3-DBREAD

3-Error

Reading file: [chars]

Fail to read a DHCPv6 binding database file.

dhcp

LOG_STD_ACTION

DLR-2-NOPROC

2-Critical

Failed to start [chars] process [chars]

Unable to create DLR process. Reloading the device might resolve the issue. Without a reload DLR will not function properly.

accsw-layer2

"Reload the device"

DLR-2-MACFAILURE

2-Critical

Ring [dec]: [chars]

Failed to update the supervisor MAC.

accsw-layer2

"Remove and reconfigure the DLR ring. Make sure that a VLAN interface has been created for the VLAN that " "the ring ports belong to. Contact TAC if the problem persists."

DLR-2-SUPRAPIDFAULT

2-Critical

Ring [dec]: The supervisor device is now in RAPID FAULT state

The supervisor device is in fault state. This happens if the device transitions from Normal to Fault state more than 5 times in 30 seconds.

accsw-layer2

"Locate the source of the faults and fix the problem before clearing the rapid fault condition"

DLR-2-SUPPARTIALFAULT

2-Critical

Ring [dec]: The supervisor device is now in PARTIAL FAULT state

The supervisor device goes to partial fault state if it detects loss of beacon frames in one direction only.

accsw-layer2

"Determine the source of the problem and fix it. The device will resume normal operation automatically."

DLR-2-RINGFAULT

2-Critical

Ring [dec]: The DLR ring is now in FAULT state

The DLR ring is in FAULT state. This typically happens if a link or node in the ring goes down.

accsw-layer2

"Determine the location of the fault and restore " "connectivity. The ring should resume functioning automatically"

DLR-2-GWFAULT

2-Critical

Ring [dec]: The redundant gateway device is now in FAULT state

The redundant gateway device is in fault state

accsw-layer2

"A redundant gateway device goes to fault state if " "all its uplinks are down. Check the status of all uplinks. Restore the connection if possible."

DLR-2-GWPARTIALFAULT

2-Critical

Ring [dec]: The redundant gateway device is now in PARTIAL FAULT state

The redundant gateway is in partial fault state

accsw-layer2

"A redundant gateway device goes to partial fault " "state if it receives messages indicating that a redundant gateway device with lower precedence" " is active. Make sure that there's bidirectional connectivity between all redundant gateway devices" " and then clear the partial fault condition."

DLR-3-EVENTFAILURE

3-Error

[chars]

A DLR event could not be handled properly.

accsw-layer2

"It could have been a temporary condition. Remove " "and reconfigure the DLR ring if the problem persists."

DLR-3-RINGCFGFAIL

3-Error

Ring [dec]: [chars]

There was an issue with the DLR ring configuration. The ring may not function properly.

accsw-layer2

"Remove and reconfigure the DLR ring. Contact TAC if the problem persists."

DLR-3-GWCFGFAIL

3-Error

Ring [dec]: [chars]

There was an issue with the DLR redundant gateway configuration. The redundant gateway may not function properly.

accsw-layer2

"Remove and reconfigure DLR redundant gateway functionality. Contact TAC if the problem persists."

DLR-3-GWUPLNKCFGFAIL

3-Error

Ring [dec]: [chars]

There was an issue with the DLR redundant gateway uplink configuration. The redundant gateway may not function properly.

accsw-layer2

"Remove and reconfigure DLR redudant gateway " "uplink configuration from the interface. Contact TAC if the problem persists."

DLR-3-SWSWITCH

3-Error

Ring [dec]: [chars] frames are being software switched

Frames which should be hardware switched are being software switched. It's normal to see this message once or twice during configuration changes but not otherwise. It can make the ring unstable and drive up the CPU utilization.

accsw-layer2

"Remove and reconfigure the DLR ring. Contact TAC if the problem persists."

DLR-6-RINGNORMAL

6-Information

Ring [dec]: The DLR ring is now in NORMAL state

The state of the DLR ring has changed to NORMAL.

accsw-layer2

"This is an informational message. The device is functioning as expected."

DLR-6-SUPSTATECHG

6-Information

Ring [dec]: The device is now the [chars] supervisor

The state of the supervisor device has changed

accsw-layer2

"This is an informational message. The device is functioning as expected."

DLR-6-GWSTATECHG

6-Information

Ring [dec]: The device is now the [chars] redundant gateway

The state of redundant gateway has changed

accsw-layer2

"This is an informational message. The device is functioning as expected."

DLR-6-SUPUNSPTPARAM

6-Information

Ring [dec]: Unsupported beacon parameters received

This backup supervisor received beacons with parameters from active supervisor which cannot be supported by this device.

accsw-layer2

"This backup supervisor device cannot take the " "role of active supervisor with current beacon parameters."

DLR-6-SUPSPTPARAM

6-Information

Ring [dec]: Supported beacon parameters received

This backup supervisor received beacons with supported parameters from active supervisor which can be supported by this device.

accsw-layer2

"This backup supervisor device can take the role of active supervisor with current beacon parameters."

DLSWP-3-PGENERAL

3-Error

[chars]

A general error condition was detected as described in the message\n\ text. This error should not cause any network problems unless it\n\ happens repeatedly.

-

LOG_STD_ACTION

DLSWP-3-PNOMEM

3-Error

No memory to [chars]

The router ran out of system memory for operation as described in the\n\ message text. Most likely the router image requires more system memory\n\ RAM than the router contains.

-

"Consult with your Cisco technical support representative\n\ about memory requirements for a specific image."

DLSWP-3-PPASSIVE

3-Error

passive open failed from [inet][dec] -> [dec]

-

-

"Consult with your Cisco technical support representative\n\ about memory requirements for a specific image."

DLSWP-3-PBADVALUE

3-Error

[chars]: invalid [chars] [dec]

A bad parameter value was passed to function chars1 - invalid\n\ parameter chars2 with value. This error should not cause any network\n\ problems unless it happens repeatedly.

-

LOG_STD_ACTION

DLSWP-3-PCAPMISMATCH

3-Error

[chars]: [chars]

The largest frame size configured in the DLSW remote peer definition\n\ is being changed because the MTU size configured\n\ on the interface used by DLSW is less than the configured value of\n\ the largest frame on DLSW remote peer definition. The largest frame size\n\ is being changed to that configured on the interface.

-

"If you wish to use this largest frame size for DLSW increase the\n\ MTU on the interface to a value larger than the configured largest\n\ frame size."

DLSWP-3-PNOCOOKIE

3-Error

uninitalized peer [chars] from [inet][dec] to [inet][dec]

DLSw received a packet on an uninitialized peer connection.

-

"Verify configuration and DLSw peer status on both routers".

DLSWP-5-PEERUPDOWN

5-Notice

[chars] [chars]

A DLSW peer is either connected or disconnected

-

"None informational message only."

DLSWP-3-PEERFAILURE

3-Error

[chars] [chars]

A DLSW peer failed:\n\\n\ - keepalive failure dlsw between cisco peers is sending a peer keepalive\n\ by default every 30 sec. After missing 3 consecutive keepalives the peer\n\ is taken down.\n\ - We are not promiscuous Rej conn from peer a.b.c.d\n\ The local dlsw peer is not configured for promiscuous and we receive\n\ a request to open a dlsw peer for which we have no corresponding dlsw\n\ remote peer statement.\n\ - received tcp fini dlsw peer code has received a tcp fini from the \n\ underlaying tcp subsystem. To obey the tcp fini dlsw wring bring down \n\ the peer connection for which the tcp fini was received.

-

"- keepalive failure\n\ Check end to end connectivity between the DLSW peers\n\ - We are not promiscuous Rej conn from peer a.b.c.d\n\ correct your configuration. \n\ - received tcp fini\n\ Check the underlaying tcp connection between the two dlsw peers."

DLSWC-3-NODLSW

3-Error

[chars] [dec]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-IDMGR

3-Error

[chars]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-NOPEER

3-Error

[chars]

A data-link switching system error occurred.

-

LOG_STD_RECUR_ACTION

DLSWC-3-BADPEEROP

3-Error

bad peer op in peer_to_core [dec]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-BADSSPHDR

3-Error

bad ssp hdr in proc ssp - [chars] = 0x[hec]

-

-

"If the remote peer is a nonCisco router confirm that it supports the\n\ DLSw RFC 1795 standard."

DLSWC-3-BADCLSIIND

3-Error

[chars] Invalid indication [chars] [chars]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-BADCLSIRET

3-Error

[chars] Invalid ret code 0x[hec] [chars] [chars]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-BADCLSICNF

3-Error

[chars] Invalid confirm [chars] [chars]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-BADCLSI

3-Error

[chars] primitive not valid for dlsw [chars] [chars]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-BADCLSISAP

3-Error

[chars] Bad clsi SAP id = [hec] [chars]

A data-link switching system error occurred.

-

LOG_STD_ACTION

DLSWC-3-SENDSSP

3-Error

SSP OP = [dec][chars] [chars] to [chars] [chars]

A Silicon Switch Program SSP frame was sent to the remote peer.

-

LOG_STD_NO_ACTION

DLSWC-3-RECVSSP

3-Error

SSP OP = [dec][chars] [chars] from [chars]

-

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMS

3-Error

[chars]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMSCSM

3-Error

[chars] [chars]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMSFSM

3-Error

[chars]: [chars] from [enet]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMSTX

3-Error

[chars]: [chars] to [enet]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMSDLX

3-Error

[chars] [hec] from [enet]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMSSAP

3-Error

[chars]: [chars]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

DLSWMasterSlave-3-DLSWMSRCV

3-Error

[chars] from [enet]

DLSw Master-Slave Error

-

LOG_STD_NO_ACTION

OSM_MULTILINK-4-IDBNULL

4-Warning

Unexpected hwidb missing in [chars]

A software error has occurred.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-4-BUNDLENULL

4-Warning

Unexpected bundle missing in [chars] searching for [chars]

A software error has occured.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-4-MLPSBNULL

4-Warning

Unexpected subblock missing for [chars]

A software error has occurred.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-4-MLPLINK_NULL

4-Warning

Unexpected mlp link missing in [chars]

A software error has occurred.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-4-NUMLINKS

4-Warning

The bundle had an unexpected number of links[dec] in [chars]

A softwate error has occured.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-5-CFGERROR

5-Notice

Cannot set up this bundle link-- [chars] to bundle [chars]\n\treason:[chars]\n

The bundle link could not be set up. A configuration of resource limit has been reached. The bundle may be forced to become inactive go down. If the line card is a CT3 line card OSM-CT3 line card

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

"Ensure that all links belong to the same group and slot. Check" " the number of links in the bundle and number of bundles in the" " group. After the configuration has been corrected enter the" " <CmdBold>shutdown<CmdBold> and <CmdBold>no shutdown<CmdBold>" " comands on the multilink interface to shut down and restart" " the interface."

OSM_MULTILINK-5-BUNDLEEXCEEDED

5-Notice

Bundle[chars] cannot be associated with link[chars] max [dec]

The number of bundles has been exceeded for the group belonging to the link. The bundle specified in the error message will not work in distributed mode. If the line card is CT3 OSM-CT3 line card then ports 1-12 belong to one group. If the

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

"Remove the multilink interface that is causing this condition."

OSM_MULTILINK-4-BUNDLEERROR

4-Warning

Bundle[chars] is not distributed

The Bundle specified in the error message is not associated with the OSM.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-3-PROCESS_FAIL

3-Error

Process creation failed for [chars]

A Process has failed to be created. The probable cause of this condition is that the system is low on memory.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

"Reduce other system activity to ease memory demands. If conditions" " warrant upgrade to a larger memory configuration."

OSM_MULTILINK-4-IPCNOTREADY

4-Warning

Bundle process on the line card is not ready to handle message of type [dec]

Bundle is being deleted on the line card due to <CmdBold>ip cef disable<CmdBold> command and is not ready to process other messages. The most likely cause of this condition is that CEF was disabled and enabled in a very quick succession.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

"Reset the line card."

OSM_MULTILINK-4-QUEUE_BUNDLE

4-Warning

Not able to queue the bundle [chars] Num. of bundles [dec]

A software error has occured while a bundle was being inserted in queue.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

OSM_MULTILINK-4-BUNDLEVC

4-Warning

[chars] for vc [dec] and if_index [dec]

A software error has occured while a bundle was being provisioned.

osm-ct3 for CT3 and osm-choc-ds0 for CHOC-12/CHOC-3

LOG_STD_SH_TECH_ACTION

RP_MLP-4-NODISTMLP

4-Warning

Failure downloading MLP bundle [chars] to the LC [dec]

The bundle is configured to be distributed but for some reasons \n\ we cannot download the MLP config to the LCd.

-

""

RP_MLP-4-MISCONFIGLINK

4-Warning

Links across linecards or dCEF disabled giving control to RP

Trying to add links to a bundle which are spread across linecards \n\ DMLP cant support this so giving control of bundle to RP.

-

""

RP_MLP-4-PANOTSUPPORTED

4-Warning

Adding Link from unsupported PA cant add giving control to RP

Trying to add links to a bundle from a PA which is not supported\n\ by DMLP so giving control of bundle to RP.

-

""

RP_MLP-4-DLFIONELINKSUPPORT

4-Warning

Only ONE link should be configured for dLFI bundle!!

Trying to configure more than ONE link for dLFI bundle interface\n\ which is not supported by dLFIoFR and dLFIoATM.

-

""

RP_MLP-5-SLOTMISMATCH

5-Notice

Link[chars] cannot be added to Bundle[chars] as [chars]

Link should be on same slot as other member links of Bundle. If this link become active bundle will not work in distributed mode

-

""

RP_MLP-5-SPAWARNING

5-Notice

Feature support switching to LC based software for [chars] as [chars]

A link was added to the bundle but it is not on the same bay as other member links of the bundle. The specified link that is not on the same bay has become active and the bundle has been switched to line card-based software support rather than the hardware mode that is supported on FREEDM.

-

"Ensure that when a link is added to a bundle " "that it is on the same bay as the other member " "links of the bundle in order to have the MLP " "bundle in hardware mode supported on FREEDM."

RP_MLP-5-LINKTYPEMISMATCH

5-Notice

Link[chars] added Bundle[chars] may not be distributed

Link speed mismatch with other member links of the bundle. If this link become active bundle will not work in distributed mode

-

""

RP_MLP-5-LEGACYCARD

5-Notice

Link[chars] added Bundle[chars] may not be distributed

Link speed mismatch with other member links of the bundle. If this link become active bundle will not work in distributed mode

-

""

RP_MLP-4-BADLINKDECONFIG

4-Warning

Bad way of removing member link now perform 'no shut' on both sides of Multilink

If member link has to be removed from multilink bundle first\n\ remove the multilink configuration from the member link and\n\ then perform no channel-group command on the controller.

-

"If the member link is removed from the multilink bundle using\n\ "no channel-group" command perform "no shut" on both sides\n\ of the multilink interface to make it work."

RP_MLP-4-CHANGEQUEUEING

4-Warning

Change the queueing on the distributed multilink interface [chars] to FCFS

When using multilink interface in distributed mode the queueing should be FCFS Please remove weighted fair or priority queueing.

-

" Please shut the multilink interface and unconfigure fair or priority" " queueing and then unshut the multilink interface"

RP_MLP-3-UNSUPPORTEDCONFIG

3-Error

The current config cannot be supported as [chars] for [chars]

When using multilink 1 The maximum number of links in the bundle and number of bundles

-

" Please modify the config as not to violate the restrictions"

RP_MLP-3-INCOMPATIBLELINK

3-Error

The current config cannot be supported as link[chars] [chars] for bundle [chars]

When using multilink 1 All the links should be from the same port.

-

" Please modify the config as not to violate the restrictions"

RP_MLP-3-ADJ_FAIL

3-Error

Adjacency walk for [chars] failed

Adjacency update for the specified multilink interface failed.

vipmlp

"Reset the multilink interface by entering the " "<CmdBold>shudown<NoCmdBold> command and then " "the <CmdBold>no shutdown<NoCmdBold> command on the interface. " "If traffic does not resume please collect the output of " "<CmdBold>show adjacency internal<NoCmdBold> and " "<CmdBold>show cef interface internal<NoCmdBold>. " LOG_STD_SH_TECH_ACTION

RP_MLP-3-UNSUPPORTED_MULTILINK

3-Error

Multilink interface supported range is 1-65535. Removing Multilink.

Multilink interface should be within 1-65535 else it is not supported

vipmlp

"Configure Multilink interface in the following range:1-65535"

RP_MLP-4-DLFIATMSERVPOLIABS

4-Warning

priority service policy aabsent with DLFIoATM on ATM SPA on Bundle [chars]

A priority service policy is needed for DLFIoATM on ATM-SPA to be able to do LFI on this interface.

-

"Please configure a priority service policy on the virtual template " "interface to enable the ATM SPA to do LFI."

RP_MLP-3-UNSUPPORTED_SERVPOLICY

3-Error

Policy map configs will be removed from interface [chars] as it is not supported.

Interface has unsupported service policy configurations

-

"Configure a valid Service Policy under the interface"

VIPMLP-2-NOVC

2-Critical

[chars]: packet received for non-existent VC [dec]

Virtual channel encapsulation is corrupted.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VIPMLP-2-NOINTERLEAVE

2-Critical

[chars] Interleave not configured due \n\ to Insufficient memory

Interleave not configured due to Insufficient memory.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DOT1AD-4-L2PT_PORT

4-Warning

Port [chars] is a l2protocol-tunnel port it conflicts with Dot1ad configuration

Dot1ad configuration cannot co-exist with l2protocol-tunnel ports.

dot1ad

"Turn off l2protocol-tunnel configuration on the ports before enabling " "Dot1ad."

DOT1AD-4-DOT1QTUNNEL_PORT

4-Warning

Port [chars] is a dot1q-tunnel port it conflicts with Dot1ad configuration

Dot1ad configuration cannot co-exist with dot1q-tunnel ports.

dot1ad

"Turn off dot1q-tunnel configuration on the ports before enabling Dot1ad."

DOT1AD-4-LACP_PORT

4-Warning

Port [chars] is a part of an LACP channel it conflicts with Dot1ad configuration

Dot1ad configuration cannot co-exist with LACP ports.

dot1ad

"Turn off LACP configuration on the ports before enabling Dot1ad."

DOT1AD-4-OAM_PORT

4-Warning

Port [chars] is configured for OAM it conflicts with Dot1ad configuration

Dot1ad configuration cannot co-exist with OAM enabled ports.

dot1ad

"Turn off OAM configuration on the ports before enabling Dot1ad."

DOT1AD-4-DOT1X_PORT

4-Warning

Port [chars] is configured for DOT1X it conflicts with Dot1ad configuration

Dot1ad configuration cannot co-exist with DOT1X enabled ports.

dot1ad

"Turn off DOT1X configuration on the ports before enabling Dot1ad."

DOT1AD-4-ETHERTYPEMISMATCH_PORT

4-Warning

Port [chars] ethertype cannot be changed to Dot1ad ethertype it conflicts with Dot1ad configuration

The ethertype on the port cannot be changed to Dot1ad ethertype.

dot1ad

"Replace the module with one which can support ethertype change or " "power down the module before enabling Dot1ad."

DOT1AD-4-STP_CONFLICT

4-Warning

STP mode conflicts with Dot1ad configuration as it is not in MST mode

Current STP mode conflicts with Dot1ad configuration.

dot1ad

"Change the STP mode to MST before enabling Dot1ad."

DOT1AD-4-PLATFORM_RESOURCE_UNAVAILABLE

4-Warning

Platform does not have resouces to support dot1ad configuration

In the 6500 platform hardware match registers are not available for dot1ad use.

dot1ad

"Unconfigure the features using the match registers cfm cgvrp and "

DRIP-3-DRIPFAIL

3-Error

DRIP: Assertion failed: [chars]

An internal software error has occurred.

-

LOG_STD_ACTION

DRIP-6-DRIP_CONFLICT

6-Information

DRIP conflict with CRF [dec].

A DRIP conflict has occured. The virtual ring or pseudo ring's\n\ CRF is being re-used in the network.

-

"Make sure that the CRF vlanid of the virtual ring and the \n\ pseudo ring is unique in the network."

DSPU-3-CLSIBadLength

3-Error

CLSI bad length header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIBadPrimitiveType

3-Error

CLSI bad primitive type header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIBadPrimitiveCmd

3-Error

CLSI bad primitive command header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIBadIdentifierType

3-Error

CLSI bad identifier type header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIBadIdentifier

3-Error

CLSI bad identifier header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIBadReturnCode

3-Error

CLSI bad return code: [dec] header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIUnexpctActSapCnf

3-Error

CLSI unexpected ActivateSapCnf header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIUnexpctDeactSapCnf

3-Error

CLSI unexpected DeactivateSapCnf header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIUnexpctIdStnInd

3-Error

CLSI unexpected IdStnInd header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIUnexpctEnableCnf

3-Error

CLSI unexpected EnableCnf header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-CLSIBadAdptCorr

3-Error

CLSI bad Adaptor correlator header= [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-DSPU_BufferCorrupted

3-Error

DSPU could not free buffer - buffer corrupted

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

DSPU-3-UnknownXid

3-Error

XID Format not supported XID= [chars]

-

-

-

DSPU-3-LSXIDNegotiationError

3-Error

XID Negotiation Error bad byte= [dec] bad bit= [dec] sense data= [chars]

-

-

"Determine from the CV 22 byte or bit information which field in the\n\ XID3 is rejected by the remote station and correct the link station\n\ configuration parameters at either the router or the remote station."

DSPU-3-LSNoACTPUCapability

3-Error

Connection attempt failed from XID= [chars] ACTPU not supported

-

-

-

DSPU-3-LSInvalidMaxIFrame

3-Error

Connection attempt failed from XID= [chars] Invalid MaxIFrame= [dec]

-

-

"Correct link station configuration at the remote station."

DSPU-3-LSInvalidWindowSize

3-Error

Connection attempt failed from XID= [chars] Invalid WindowSize= [dec]

-

-

"Correct link station configuration at the remote station."

DSPU-3-LSConnOutToHostFailed

3-Error

Connect out to host [chars] failed.

Connection with the remote host could not be established.

-

"Verify host configuration parameters at the router and at the host.\n\ Determine whether the host is active and responding to connection\n\ requests."

DSPU-3-LSConnOutToPuFailed

3-Error

Connect out to pu [chars] failed.

Connection with the remote PU could not be established.

-

"Verify PU configuration parameters at the router and at the remote PU.\n\ Determine whether the remote PU is active and responding to connection\n\ requests."

DSPU-3-LSConnInFromHostFailed

3-Error

Connect in from host [chars] with remote address [chars] failed.

Connection with the remote host could not be established.

-

"Verify host configuration parameters at the router and at the host.\n\ Determine whether the router is configured to accept connection from\n\ this host."

DSPU-3-LSConnInFromPuFailed

3-Error

Connect in from pu [chars] with remote address [chars] failed.

Connection with the remote PU could not be established.

-

"Verify PU configuration parameters at the router and at the remote PU.\n\ Determine whether the router is configured to accept connectIn from\n\ this remote PU."

DSPU-3-LSConnInFailed

3-Error

Connect in from remote address [chars] failed.

Connection with the remote station could not be established because of\n\ insufficient memory in the router.

-

"Correct low memory problem in the router. If the problem persists\n\ call your technical support representative for assistance."

DSPU-3-SnaBadData

3-Error

Bad SNA data received from PU [chars] data= [chars]

Unrecognized SNA data was received from the remote PU.

-

"Correct the problem at the remote PU. If the problem persists call\n\ your Cisco technical support representative for assistance."

DSPU-3-ActpuNegResponse

3-Error

ACTPU Neg rsp received from PU [chars]

Remote PU rejected the router's request for an SSCP-PU session.

-

"Verify PU configuration parameters at the router and at the remote PU.\n\ Determine whether the problem exists at the remote PU and correct it.\n\ If the problem persists call your Cisco technical support\n\ representative for assistance."

DSPU-3-NotifyNegRsp

3-Error

LU [dec] received a Notify Neg Resp from host [chars]

Remote host rejected the router's request to activate/deactivate an\n\ SSCP-LU session.

-

"Verify host configuration parameters at the router and at the remote\n\ host. Determine whether the problem exists at the remote host and\n\ correct it. If the problem persists call your technical support\n\ representative for assistance."

PMDWDM-4-TCA

4-Warning

[chars]: [chars] [chars] [chars] value %lld threshold %lld [chars]

The specified PM FEC TCA has been declared or released

g709-dwdm

"Recommended action is to repair the source of the alarm."

DWDM-4-G709ALARM

4-Warning

[chars]: [chars] [chars]

The specified G709 Alarm has been declared or released

g709-dwdm

"Recommended action is to repair the source of the alarm."

DWDM-3-RPC_PROCESSING_ERROR

3-Error

DWDM RPC error: [chars]

Non Fatal error occured in processing an RPC messsage.

g709-dwdm

show version

DWDM-3-RPC_INIT_FAIL

3-Error

DWDM RPC init failure

The system failed to create the resources required to process user\n\ interface commands for transceivers. The error is not fatal but \n\ some \show\ commands could fail.

g709-dwdm

show version

DWDM-3-RPC_FAILED

3-Error

Application error rc = [dec]:

The system failed to retrieve the information required to \n\ execute the command

g709-dwdm

show version

DWDM-3-DWDM_NULL_INFO

3-Error

DWDM info is NULL in [dec]

The SPA driver detected NULL information for DWDM

spa-eth-10ge

"Reload the SPA and if the problem persists" "contact the technical support representative"

DWDM-3-DWDM_CONFIG_FAIL

3-Error

Failed to [chars] [chars] in slot [dec] rc = [dec]

The SPA driver detected failure during configuring one of the DWDM parameters

spa-eth-10ge

"Reload the SPA card and if the problem" "persists call the tachnical assistance centre"

DWDM-3-MALLOC_FAIL

3-Error

malloc failure creating \ G.709 port on slot [dec]

The SPA driver detected a memory error on the SPA card

spa-eth-10ge

"Reload the card and if the problem persists " " call TAC"

DWDM-3-CONFIG_TX_POWER

3-Error

Failed to config \ transmit power [dec] on slot [dec] rc = [dec]

The SPA driver detected a error in configuring the Tx power level for the UT2 transponder module

spa-eth-10ge

"Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

DWDM-3-RX_LOS_THRESHOLD

3-Error

Failed to config \ rx los threshold = [dec] on slot [dec] rc = [dec]

The SPA driver detected an error in configuring the transponder receive power threshold

spa-eth-10ge

"Reload the SPA card and if the problem persists" "call TAC"

DWDM-3-CONFIG_ALARM_REPORT

3-Error

Failed to config report\n\ alarm [chars] slot [dec] rc = [dec]

The SPA driver could not configure one of the reporting status of the alarms

spa-eth-10ge

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-CONFIG_ALARM_THRESHOLD

3-Error

Failed to config threshold \n\ alarm [chars] slot [dec] rc = [dec]

The SPA driver could not configure one of the threshold alarms for the optical data or transport unit

spa-eth-10ge

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-DWDM_GET_INFO_FAIL

3-Error

Failed receiving [chars] \ from slot [dec] rc = [dec]

The SPA driver did not receive the necessary optics information from the slot

spa-eth-10ge

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-RX_G709_INFO

3-Error

Failed receiving G709 info \ from slot [dec] rc = [dec]

The SPA driver did not receive the necessary G.709 OTN protocol information from the slot

spa-eth-10ge

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-CLEAR_G709_CTR

3-Error

Unable to clear g709 \ counter in slot [dec] rc = [dec]

The SPA driver was unable to clear the G.709 OTN protocol counters for bit errors

spa-eth-10ge

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-IPC_SHIM_INIT

3-Error

DWDM IPC SHIM init failed

The SPA driver detected failure during DWDM IPC SHIM initialization

spa-eth-10ge

"Please power down and reseat the indicated SPA card" "If the problem persists please contact your" "technical support representative"

DWDM-3-TIMER_ERR

3-Error

Timer error

The Driver did not obtain an expired timer from the timer tree for the DWDM process

spa-eth-10ge

"The SPA driver has encountered an error event on the SPA card." "If the condition persists copy the error message exactly as " "it appears or contact " "your technical support representative"

DWDM-3-LC_ERR_STATS

3-Error

error sending LC stats to RP

The SPA driver encountered an error while sending the LC stats to the RP

spa-eth-10ge

"Reload the SPA card and if the problem persists" "call the technical support representative"

DWDM-3-CONFIG_OVERHEAD_TTI

3-Error

Failed to config [chars] [chars] slot [dec] rc = [dec]

The LC driver could not configure the tail trace identifier for the optical data or transport unit

-

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-CONFIG_PM

3-Error

Failed to config [chars] [chars] slot [dec] rc = [dec]

The LC driver could not configure the PM parameters for the optical data or transport unit

-

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative"

DWDM-3-OTN_STATS_CREATE_IF_FAILED_TO_ALLOCATE

3-Error

stats for interface index [dec] could not be created with status [dec]

-

snmp-otn

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

DWDM-3-OTN_STATS_CREATE_IF_FAIL

3-Error

stats for interface index [dec] could not be created with status [dec]

-

snmp-otn

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

DWDM-3-OTN_STATS_DELETE_IF_FAIL

3-Error

stats for interface index [dec] could not be deleted with status [dec]

-

spa-eth-10ge

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

PPROT_FSM-3-TRANSIT_EVENT

3-Error

Invalid event [dec] while processing transit event queue

Invalid event while processing transit event queue

g709-dwdm

LOG_STD_ACTION

PPROT_FSM-3-PROC_ALL_TRANSIT_EVENT

3-Error

All events could not be processed in transit queue

All events could not be processed in transit queue

g709-dwdm

LOG_STD_ACTION

PPROT_FSM-4-FSM_FIND_INFO_FAIL

4-Warning

Could not find element if_number [dec] in FSM list

Could not find element in FSM list

g709-dwdm

LOG_STD_ACTION

PPROT_FSM-3-CREATE_FAIL

3-Error

creation failed : [chars]

creation failed

g709-dwdm

LOG_STD_ACTION

PPROT_FSM-3-MALLOC_FAIL

3-Error

malloc failed : [chars]

malloc failed

g709-dwdm

LOG_STD_ACTION

PPROT_FSM-3-CHUNK_CREATE

3-Error

chunk create failed

chunk create failed

g709-dwdm

LOG_STD_ACTION

PPROT_L3_TRIG-3-MALLOC_FAIL

3-Error

malloc failed: [chars]

malloc failed

g709-dwdm

LOG_STD_ACTION

PPROT_L3_TRIG-3-ISSU_COMP_FAIL

3-Error

L3 trigger xdr priority msg not issu compatible

L3 trigger xdr priority msg not issu compatible

g709-dwdm

LOG_STD_ACTION

PPROT_L3_TRIG-3-INVALID_CLIENT_TYPE

3-Error

Invalid client type [dec] from xdr

invalid client type from xdr

g709-dwdm

LOG_STD_ACTION

PPROT_L3_TRIG-3-CHUNK_CREATE

3-Error

chunk create failed

chunk create failed

g709-dwdm

LOG_STD_ACTION

DYINGGASP-0-POWER_LOSS

0-Emergency

Shutdown due to power loss

This is a fail over message which is logged if this unit is about to shutdown due to power loss.

-

"Verify that the unit is powered on and power cables are" " connected correctly."

DYINGGASP-6-HOST_NOT_SUPP

6-Information

[chars] host [inet] is not supported for dyinggasp notification due to [chars]\n

This message id logged if dying gasp ignores either SNMP or Syslog host for dying gasp notification.

-

"No action necessary"

DTP-4-MEM_UNAVAIL

4-Warning

Memory was not available to perform the trunk negotiation action

Unable to negotiate trunks because of a lack of memory

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

DTP-4-UNKN_ERR

4-Warning

An unknown operational error occurred

Unable to negotiate trunks because an internal operation\n\ generated an error which was not expected to ever happen.

-

"Because of the unexpected nature of the problem the only recommended\n\ action is to reload the device"

DTP-5-TRUNKPORTON

5-Notice

Port [chars] has become [chars] trunk

The specified port has changed from being an access port to a trunk\n\ port using the specified encapsulation.

-

""

DTP-5-NONTRUNKPORTON

5-Notice

Port [chars] has become non-trunk

The specified port has changed from being a trunk port to an access\n\ port.

-

""

DTP-5-TRUNKPORTCHG

5-Notice

Port [chars] has changed from [chars] trunk to [chars] trunk

The specified trunk port has changed the encapsulation type is uses.

-

""

DTP-5-ILGLCFG

5-Notice

Illegal configonisl--ondot1q on [chars]

The two ports on the link are set to the ON mode but one is set to\n\ 802.1Q encapsulation while the other is set to ISL encapsulation.\n\ When both ports on a link are set to the ON mode their encapsulation\n\ types must match

-

"Configure both ports on the link to have the same encapsulation."

DTP-4-TMRERR

4-Warning

An internal timer error occurred when trunking on interface [chars]

There might be some instances in which a timer used by the trunking\n\ protocol expires at a time when it is unexpected. This problem is\n\ corrected internally.

-

"There is likely no long-term ramifications from this problem. However\n\ if further problems with trunking are seen it is recommended that you\n\ reload the device."

DTP-5-DOMAINMISMATCH

5-Notice

Unable to perform trunk negotiation on port [chars] because of VTP domain mismatch.

The two ports involved in trunk negotiation belong to different \n\ VTP domains. Trunking is possible only when the ports involved belong to\n\ the same VTP domain.

dtp

"Ensure that the two ports that are involved in trunk negotiation belong to\n\ the same VTP domain."

ENT_API-3-NOCREAT

3-Error

EntityApiProcess not created - Entity MIB will not be \n\ initialised

Attempt to start EntityApiProcess failed when the entity subsystem \n\ was initialised. The Entity MIB will not be populated.

snmp

"The Entity MIB API process was not created possibly due to\n\ lack of memory. If you want to use the Entity MIB API \n\ reconfigure the box so that less memory is used by\n\ other features or add more memory to the system. Reload the box\n\ after reconfiguring."

ENT_API-4-NOPARENT

4-Warning

Parent physical entity [dec] did not exist when trying to add\n\ child physical entity [dec] phyDescr = [chars] phyName = [chars].

An attempt to add a physical entity failed because its\n\ parent physical entity did not exist in the entPhysicalTable\n\ of the Entity MIB.

snmp

"Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table."

ENT_API-3-NOPARENTDEL

3-Error

Parent physical entity [dec] did not exist when trying to delete\n\ child physical entity [dec] phyDescr = [chars] phyName = [chars]. RootIdx = [dec]

An attempt to reassign parent's child pointer reference failed during\n\ the node deletion because the node's parent reference is NULL. The node\n\ and all of its sibling nodes and their childeren will be deleted. This\n\ is an unususal scenario and may happen due to any hardware malfunction\n\ such as device flapping.

snmp

"Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table."

ENT_API-4-NOLPMAP

4-Warning

[chars] entity not found when adding an LPMapping entry with \n\ logical index = [dec] and physical index = [dec] to the Entity MIB

An attempt to add an LPMapping entry to the Entity MIB was made.\n\ The logical or physical entity with the specified index does\n\ not exist and so the LPMapping entry creation failed.

snmp

"Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table."

ENT_API-4-NOALIAS

4-Warning

[chars] entity not found when adding an alias with \n\ physical index = [dec] and logical index = [dec] to the Entity MIB

An attempt to add an alias entry to the Entity MIB was made.\n\ The logical or physical entity with the specified index does\n\ not exist and so the alias entry creation failed.

snmp

"Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table."

ENT_API-4-NOPORT

4-Warning

Physical entity does not have a Port PhysicalClass when \n\ adding an alias with physical index = [dec] logical index = [dec]\n\ phyDescr = [chars] phyName = [chars]\n\ phyClass = [dec] phyContainedIn = [dec] to the Entity MIB

-

snmp

"Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table."

ENT_API-4-NOENT

4-Warning

Trying to add or delete an unknown entity to the Entity MIB

An attempt to add/delete an unknown entity to the Entity MIB \n\ was made. The request could not be processed.

snmp

"Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table."

ENT_API-4-MULTIPLEREG

4-Warning

Multiple registration request with same entity name = [chars] \n\ using entity index [dec] and phyDescr = [chars].

An attempt to register a physical entity happened and failed \n\ because the same entity name is being used for which a registration \n\ has already been done.

snmp

"Need to raise a DDTS with the component responsible for the \n\ for the registration to use different entity names for registering \n\ different entities."

SENSORMGR-3-NOMEM

3-Error

Sensor manger failed to allocate memory : [chars]

The sensor manager was not able to add a new threshold node to its database.

sensor-mgr

"TBD"

ETHERNET_OAM-2-CRIT_ERR

2-Critical

The Ethernet OAM protocol has encountered the critical error: [chars].

The protocol has run into a critical error. The reason should be given in the brackets.

ether-oam

LOG_STD_ACTION

ETHERNET_OAM-6-CRITICAL_EVENT

6-Information

The client on interface [chars] has received a Critical Event indication from its remote peer action = [chars]

An OAMPDU has been received from the remote client that indicates a Critical Event has occurred. The indicated action will be performed. If the action is error-block the link will go into error-block state where data traffic is blocked but link-oam can still be exchanged. If the action is error-disable the link is brought down.

ether-oam

"Investigate the issue on the remote peer"

ETHERNET_OAM-6-DYING_GASP

6-Information

The client on interface [chars] has received a Dying Gasp indication from its remote peer failure reason = [chars] action = [chars]

An OAMPDU has been received from the remote client that indicates a Dying Gasp which may signal that the remote client is about to go down. The indicated action will be performed. If the action is error-block the link will go into error-block state where data traffic is blocked but link-oam can still be exchanged. If the action is error-disable the link is brought down.

ether-oam

"Investigate the issue on the remote peer"

ETHERNET_OAM-6-LINK_FAULT

6-Information

The client on interface [chars] has received a Link Fault indication from its remote peer action = [chars]

An OAMPDU has been received from the remote client that indicates a Link Fault has been detected. This indicates a fault has occurred in the receive direction of the sending client. The indicated action will be performed. If the action is error-block the link will go into error-block state where data traffic is blocked but link-oam can still be exchanged. If the action is error-disable the link is brought down.

ether-oam

"Check the wiring between the two interfaces."

ETHERNET_OAM-6-CRITICAL_EVENT_CLEAR

6-Information

The client on interface [chars] has received a clear of the Critical Event indication from its remote peer action = [chars]

An OAMPDU has been received from the remote client that indicates that the Critical Event condition previously seen has cleared. If the action was error-block traffic on the link will now be re-enabled. Error-disable state can only be cleared by performing a shut/no shut of the interface.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-6-DYING_GASP_CLEAR

6-Information

The client on interface [chars] has received a clear of the Dying Gasp indication from its remote peer action = [chars]

An OAMPDU has been received from the remote client that indicates that the Dying Gasp condition previously seen has cleared. If the action was error-block traffic on the link will now be re-enabled. Error-disable state can only be cleared by performing a shut/no shut of the interface.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-6-LINK_FAULT_CLEAR

6-Information

The client on interface [chars] has received a clear of the Link Fault indication from its remote peer action = [chars]

An OAMPDU has been received from the remote client that indicates that the Link Fault condition previously seen has cleared. If the action was error-block traffic on the link will now be re-enabled. Error-disable state can only be cleared by performing a shut/no shut of the interface.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-5-LINK_MONITOR

5-Notice

[chars] detected over the last [chars] on interface [chars].

A monitored error has been detected to have crossed the user-specified threshold.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-5-EVENTTLV

5-Notice

[chars] is received from the remote client on interface [chars].

An Event TLV is received from the remote OAM client. It must have detected errors in receiving frames from this local interface.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-6-LOOPBACK

6-Information

Interface [chars] has [chars] the [chars] loopback mode.

The specified interface has entered or exited loopback mode because of protocol control or an external event such as the interface link going down.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-3-LOOPBACK_ERROR

3-Error

Loopback operation on interface [chars] has encountered an error[chars].

Because of the specified error the loopback operation has ended abnormally.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-6-ENTER_SESSION

6-Information

The client on interface [chars] has entered the OAM session.

Ethernet OAM client on the specified interface has detected a remote client and has entered the OAM session.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-6-EXIT_SESSION

6-Information

The client on interface [chars] has left the OAM session.

Ethernet OAM client on the specified interface has experienced some state change.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-6-LINK_TIMEOUT

6-Information

The client on interface [chars] has timed out and exited the OAM session.

The Ethernet OAM client on the specified interface has not received any OAMPDUs in the number of seconds for timeout that were configured by the user. The client has exited the OAM session.

ether-oam

LOG_STD_NO_ACTION

ETHERNET_OAM-4-ISSU_INCOMPATIBLE

4-Warning

\nether_oam-issu-compat: returned FALSE

The compatibility checking has failed

ether-oam

LOG_STD_SH_TECH_ACTION

ETHERNET_OAM-3-TRANSFORM_FAIL

3-Error

ETHERNET OAM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The ETHERNET OAM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ETHERNET OAM state between the active device and the standby device is not identical.

ether-oam

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHERNET_OAM-2-GET_BUFFER

2-Critical

ETHERNET OAM ISSU client failed to get buffer for message. Error: [dec] [chars]

The ETHERNET OAM ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ether-oam

"show logging and show checkpoint client"

ETHERNET_OAM-3-SESSION_UNREGISTRY

3-Error

ETHERNET OAM ISSU client failed to unregister session information. Error: [dec] [chars]

The ETHERNET OAM ISSU client failed to unregister session information.

ether-oam

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHERNET_OAM-2-INIT

2-Critical

ETHERNET OAM ISSU client initialization failed to [chars]. Error: [dec] [chars]

The ETHERNET OAM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ether-oam

LOG_STD_ACTION

ETHERNET_OAM-2-SEND_NEGO_FAILED

2-Critical

ETHERNET OAM ISSU client failed to send negotiation message. Error: [dec] [chars]

The ETHERNET OAM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ether-oam

"show logging and show checkpoint client"

ETHERNET_OAM-2-SESSION_REGISTRY

2-Critical

ETHERNET OAM ISSU client failed to register session information. Error: [dec] [chars]

The ETHERNET OAM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ether-oam

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHERNET_OAM-3-INVALID_SESSION

3-Error

ETHERNET OAM ISSU client does not have a valid registered session.

The ETHERNET OAM ISSU client does not have a valid registered session.

ether-oam

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHERNET_OAM-3-MSG_SIZE

3-Error

ETHERNET OAM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The ETHERNET OAM ISSU client failed to calculate the MTU for the specified message. The ETHERNET OAM ISSU client is not able to send the message to the standby device.

ether-oam

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHERNET_OAM-2-SESSION_NEGO

2-Critical

ETHERNET OAM ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The ETHERNET OAM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ether-oam

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

EM-3-EXCEED

3-Error

EM exceed maximum open events [dec].

The total number of open events exceeded the maximum number of possible open events. The maximum number that the EM server permits is specified in the error message. EM clients are either opening too many events or not closing events within the permitted time period.

-

show em state | inc <em_type>

EM-3-NULLPTR

3-Error

The pointer in a specified EM function [chars] is incorrectly NULL.

The pointer in the specified EM function is incorrectly NULL. This condition might be caused by incorrect logic or a memory corruption.

-

"Copy the error message exactly as it appears on the console or " "in the system log. Enter the <CmdBold>show em state<NoCmdBold> " "command or the <CmdBold>show em status<NoCmdBold> command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information."

EM-3-FAIL

3-Error

The specified EM Function failed [chars].

The specified EM function failed. This condition might be caused by incorrect logic or a memory corruption.

-

"Copy the error message exactly as it appears on the console or " "in the system log. Enter the <CmdBold>show em state<NoCmdBold> " "command or the <CmdBold>show em status<NoCmdBold> command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information."

EM-3-NOMEM

3-Error

The EM failed to allocate memory resources for the specified\nEM \function [chars].

A timeout occurred. This condition is minor and should not affect the functionality of the switch.

-

"This message should not affect switch functionality but can be " "sign of a software bug condition. Please check Bug Toolkit on " "the Cisco web-site for relevant bugs against this message. If " "you do not find any please contact the TAC with the output of " "<CmdBold>show em client<NoCmdBold>"

EM-4-INVALID

4-Warning

The specified EM function [chars] received Invalid operands <[dec]>.

The EM client used invalid API parameters.

-

"Copy the error message exactly as it appears on the console or " "in the system log. Enter the <CmdBold>show em state<NoCmdBold> " "command or the <CmdBold>show em status<NoCmdBold> command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information."

EM-4-SENDFAILED

4-Warning

The specified EM client type=[dec] failed to send messages to standby.

Because the specified EM client failed to send messages to the standby supervisor engine the standby supervisor engine is not updated. Do not attempt to failover to standby supervisor engine.

-

show checkpoint clients

EM-4-NOTUP

4-Warning

The EM is not available [chars].

The specified EM function could not find the specified open event. This condition might be caused by a memory corruption.

-

"Copy the error message exactly as it appears on the console or " "in the system log. Enter the <CmdBold>show em state<NoCmdBold> " "command or the <CmdBold>show em status<NoCmdBold> command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information."

EM-4-LIMIT

4-Warning

EM exceed open events limit [dec].

The EM has exceeded the permitted number of open events. The open event limit is 5000.

-

LOG_STD_ACTION

EM_ISSU-2-INIT

2-Critical

Event Manager ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Event Manager ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

em

LOG_STD_ACTION

EM_ISSU-3-TRANSFORM_FAIL

3-Error

Event Manager ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Event Manager ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Event Manager state between the active device and the standby device is not identical.

em

"show issu session <client_id> and " "show issu negotiated version <session_id>"

EM_ISSU-3-MSG_NOT_OK

3-Error

Event Manager ISSU client 'Message Type [dec]' is not compatible

The Event Manager ISSU client received an incompatible message from the peer device. The message cannot be processed.

em

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

EM_ISSU-3-OPAQUE_MSG_NOT_OK

3-Error

Event Manager ISSU client 'Opaque Message Type [dec]' is not compatible

The Event Manager ISSU client received an incompatible message from the peer device. The opaque message cannot be processed.

em

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

EM_ISSU-3-MSG_SIZE

3-Error

Event Manager ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Event Manager ISSU client failed to calculate the MTU for the specified message. The Event Manager ISSU client is not able to send the message to the standby device.

em

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

EM_ISSU-3-INVALID_SESSION

3-Error

Event Manager ISSU client does not have a valid registered session.

The Event Manager ISSU client does not have a valid registered session.

em

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

EM_ISSU-2-SESSION_REGISTRY

2-Critical

Event Manager ISSU client failed to register session information. Error: [dec] [chars]

The Event Manager ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

em

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

EM_ISSU-3-SESSION_UNREGISTRY

3-Error

Event Manager ISSU client failed to unregister session information. Error: [dec] [chars]

The Event Manager ISSU client failed to unregister session information.

em

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

EM_ISSU-2-SESSION_NEGO

2-Critical

Event Manager ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Event Manager ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

em

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

EM_ISSU-2-SEND_NEGO_FAILED

2-Critical

Event Manager ISSU client failed to send negotiation message. Error: [dec] [chars]

The Event Manager ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

em

"show logging and show checkpoint client"

EM_ISSU-2-GET_BUFFER

2-Critical

Event Manager ISSU client failed to get buffer for message. Error: [dec] [chars]

The Event Manager ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

em

"show logging and show checkpoint client"

EXPRESSION-3-BADTYPE

3-Error

Found data type [hec] in expression should be [chars] type

While evaluating an expression an operand was found with an unexpected\n\ datatype. Evaluation of this expression has been aborted.

snmp

"Copy the error message exactly as it appears and report it to\n\ your technical support representative."

EXPRESSION-3-FAILASSERT

3-Error

Assertion failed: [chars]

An operation within the Expression MIB subsystem encountered\n\ a data value that is out of range or of an unexpected value\n\ indicative of a logic error within the subsystem.

snmp

"Copy the error message exactly as it appears and report it to\n\ your technical support representative."

EVENT-3-INSERT_FAILURE

3-Error

Failed to insert [chars]

The event process failed to insert the newly created row in\n\ its linked list data structure

snmp

"Copy the error message exactly as it appears and report it to\n\ your technical support representative."

EVENT-3-NULL_STRUCT

3-Error

Null pointer to the [chars] structure

The process was woken up with an element which had a null pointer to\n\ the test structure

snmp

"Copy the error message exactly as it appears and report it to\n\ your technical support representative."

EVENT-3-NULL_ELEMENT

3-Error

Null pointer in the watched queue for [chars] test

The process was woken up with an NULL element

snmp

"Copy the error message exactly as it appears and report it to\n\ your technical support representative."

X40G-5-TCAM_MGR_INFO

5-Notice

[chars]

X40G TCAM driver error

c7600-es-platform

LOG_STD_SH_TECH_ACTION

X40G-3-TCAM_MGR_ERR

3-Error

GTM ERROR: [chars] [dec]

X40G TCAM MGR interaction error

c7600-es-platform

LOG_STD_SH_TECH_ACTION

X40G-3-TCAM_MGR_HW_ERR

3-Error

GTM HW ERROR: [chars] [dec] [[dec]:%05x]

X40G TCAM hardware error

c7600-es-platform

LOG_STD_SH_TECH_ACTION

X40G-3-TCAM_MGR_HW_PERR

3-Error

GTM HW ERROR: [chars] [dec]

X40G TCAM interface parity error

c7600-es-platform

LOG_STD_SH_TECH_ACTION

X40G-2-TCAM_MGR_CRIT_ERR

2-Critical

GTM ERROR: [chars] [dec]

X40G TCAM critical error

c7600-es-platform

LOG_STD_SH_TECH_ACTION

X40G-4-TCAM_MGR_ALLOC_ERR

4-Warning

[chars] NP [dec] Region Id [dec]

NP TCAM entry allocation failure

c7600-es-platform

"remote command module " "<module#> sh platform software xtcammgr instance <NP#> info"

ELC_L2_ACL-3-NOMEM

3-Error

Memory Allocation Failure - [chars] : [chars]0x[hec]

Memory required by l2 acl client to service one or more Network Processors could not be allocated.

asr1k-ether-lc

"This error may indicate that more memory must be installed on the " "affected card or platform in order to service all the features and " "related entities enabled via the configuration. " LOG_STD_SH_TECH_ACTION

ELC_L2_ACL-3-ERRORSW

3-Error

[chars]

The elc l2 acl client detected software error event that is specified in the message

asr1k-ether-lc

LOG_STD_SH_TECH_ACTION

RFS-3-CLIENT_REG

3-Error

RFS Client [dec] Registration failed

RFS ISSU client registration failed

-

"Enter the following command:'show issu client' and " "copy the error and send it to TAC. TAC team can contact the " "file-systems team to check why no uid with this value found " "registered in ISSU Database"

RFS-3-ENTITY_REG

3-Error

RFS Entity [dec] Registration failed

RFS ISSU entity failed to register with ISSU

-

"Enter the following command:'show issu entities' " "and copy the error and send it to TAC. TAC team can contact the " "file-systems team to check why this entity failed to register"

RFS-3-MSGTYPE_REG

3-Error

RFS Msg Type for Entity [dec] Registration failed

RFS ISSU Msg Type registration failed

-

"Enter the following commands: " "'show issu entities' 'show issu message types' and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why this message types failed to register"

RFS-3-MSGGROUP_REG

3-Error

RFS Msg Group [dec] for Entity [dec] Registration failed

RFS ISSU Msg Group registration failed

-

"Enter the following commands: 'show issu message groups' \and copy the error and send it to TAC. TAC team can contact the \file-systems team to check why this message group failed to register"

RFS-3-CAPTYPE_REG

3-Error

RFS Cap Type for Entity [dec] Registration failed

RFS ISSU Cap Type registration failed

-

"Enter the following commands: 'show issu capability types' and copy " "the error and send it to TAC. TAC team can contact the file-systems " "team to check why this capability type failed to register"

RFS-3-CAPENTRY_REG

3-Error

RFS Cap Entry [dec] for Entity [dec] Registration failed

RFS ISSU Cap Entry registration failed

-

"Enter the following commands: show issu capability entries and copy " "the error and send it to TAC. TAC team can contact the file-systems " "team to check why this capability entry failed to register"

RFS-3-CAPGROUP_REG

3-Error

RFS Cap Group [dec] for Entity [dec] Registration failed

RFS ISSU Cap Group registration failed

-

"Enter the following commands: show issu capability groups and copy " "the error and send it to TAC. TAC team can contact the file-systems " "team to check why this capability group failed to register"

RFS-3-CLIENT_SESSION_REG

3-Error

RFS ISSU client shared msg session for entity [dec] registration failed

RFS ISSU client shared msg session registration failed

-

"Enter the following commands: show issu sessions and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why this shared message session failed to register"

RFS-3-CLIENT_SESSION_UNREG

3-Error

RFS session [dec] Un-Registration failed

RFS ISSU client session un-registration failed

-

"Enter the following commands: show issu sessions and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why this client session failed to un-register"

RFS-3-NEGO_SESSION_REG

3-Error

RFS nego session for Entity [dec] Registration failed

RFS ISSU shared nego session registration failed

-

"Enter the following commands: 'show issu sessions' 'show issu " "entities' and copy the error and send it to TAC. TAC team can " "contact the file-systems team to check why this client negotiation " "session failed to register"

RFS-3-NEGO_SESSION_UNREG

3-Error

RFS session [dec] Un-Registration failed

RFS ISSU shared nego session un-registration failed

-

"Enter the following commands: 'show issu sessions' and copy the " "error and send it to TAC. TAC team can contact the file-systems " "team to check why this client negotiation session failed to " "un-register"

RFS-3-START_NEGO_SESSION

3-Error

RFS nego [dec]:[dec] to [[chars]:0x[hec]] failed: [[chars]]

RFS ISSU start shared nego session failed

-

"Enter the following commands: 'show issu sessions' and copy the " "error and send it to TAC. TAC team can contact the file-systems " "team to check why this client negotiation session failed to start"

RFS-3-NEGO_COMP

3-Error

RFS nego is not compatible [dec]

RFS ISSU start shared nego session failed

-

"Enter the following commands: 'show issu sessions' and copy the " "error and send it to TAC. TAC team can contact the file-systems " "team to check why this client negotiation session is not compatible"

RFS-3-SEND_NEGO_MESSAGE

3-Error

RFS send nego message %p failed

RFS ISSU send nego message failed

-

"Enter the following commands: 'show issu session' and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why this client negotiation message failed"

RFS-3-RECEIVE_NEGO_FAILED

3-Error

RFS receive nego message %p failed

RFS ISSU receive nego message failed

-

"Enter the following commands: 'show issu session' and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why this client negotiation message failed"

RFS-3-RECEIVE_NEGO_NOT_DONE

3-Error

RFS receive nego message is not done [dec]

RFS ISSU receive nego message is not done

-

"Enter the following commands: show issu session and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why this client negotiation failed to complete"

RFS-3-IPC_GET_BUFFER

3-Error

RFS issu ipc get buffer failed

RFS ISSU ipc get buffer failed

-

"Enter the following commands:'show proc mem' or 'show buffs' to " "check if memory or buffer is full. shutdown unused tasks or reset " "cards usually can recover those memory leak problem. Copy the error " "and send it to TAC if those actions do not help."

RFS-3-REG_PORT

3-Error

RFS reg port [dec] failed

RFS ISSU reg port failed

-

"Enter the following commands: show ipc port and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this port failed to register"

RFS-3-LOCATE_PORT

3-Error

RFS locates port [chars] failed

RFS ISSU locates port failed

-

"Enter the following commands: show ipc port and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this ipc port could not be located"

RFS-3-OPEN_CLIENT_PORT

3-Error

RFS open client port [chars] failed. Reason:[chars]

RFS ISSU open client port failed

-

"Enter the following commands: show ipc port and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this ipc port could not be opened"

RFS-3-OPEN_SERVER_PORT

3-Error

RFS open server port [chars] failed

RFS ISSU open server port failed

-

"Enter the following commands: show ipc port and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this ipc port could not be opened"

RFS-3-CREATE_CLIENT_PORT

3-Error

RFS create client port [chars] failed

RFS ISSU create client port failed

-

"Enter the following commands: show ipc port and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this ipc port could not be created"

RFS-3-CREATE_SERVER_PORT

3-Error

RFS create server port [chars] failed

RFS ISSU create server port failed

-

"Enter the following commands: show ipc port and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this ipc port could not be created"

RFS-3-RFS_ISSU_START_SESSION

3-Error

RFS create rfs_issu_start_session watch boolean failed

RFS ISSU create rfs_issu_start_session watch boolean failed

-

"Copy the error and send it to TAC. TAC team can contact the " "file-systems team to check why this ipc port could not be created"

RFS-3-RFS_ISSU_START_PORT

3-Error

RFS create rfs_issu_start_port watch boolean failed

RFS ISSU create rfs_issu_start_port watch boolean failed

-

"Enter the following commands:show proc mem and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this watched boolean could not be created"

RFS-3-RFS_ISSU_NEGO_PROCESS

3-Error

RFS create rfs_issu_start_port watch boolean failed

RFS ISSU create nego process failed

-

"Enter the following commands:show proc mem and copy the error and " "send it to TAC. TAC team can contact the file-systems team to check " "why this watched boolean could not be created"

RFS-3-MSG_MTU

3-Error

RFS Client [dec] get msg mtu failed. Error = [dec]

RFS ISSU client get msg mtu failed

-

"Enter the following commands: show issu fsm show issu ses and copy " "the error and send it to TAC. TAC team can contact the file-systems " "team to check why get message mtu failed"

RFS-3-MSG_XMIT

3-Error

RFS Client [dec] on session [dec] to seat [0x[hec]] failed send

RFS ISSU client send msg failed

-

"Enter the following commands:show issu sessions and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why send message for this client failed"

RFS-3-MSG_RCV

3-Error

RFS Client [dec] on session [dec] to seat [0x[hec]] failed receive

RFS ISSU client receive msg failed

-

"Enter the following commands:show issu sessions and copy the error " "and send it to TAC. TAC team can contact the file-systems team to " "check why receive message for this client failed"

RFS-3-UNREG_ENTITY

3-Error

RFS ISSU Client unreg entity failed.

RFS ISSU client unreg entity failed

-

"Enter the following command:'show issu entities' " "and copy the error and send it to TAC. TAC team can contact the " "file-systems team to check why this entity failed to un-register"

RFS-3-RFS_ISSU_CLIENT_OR_ENTITY_ID

3-Error

RFS ISSU couldnt find client/entity id in peer.

RFS ISSU couldnt find client/entity id in peer.

-

"Enter the following command:'show issu entities' " "and copy the error and send it to TAC. TAC team can contact the " "file-systems team to check why this client/entity id coudlnt find " "in peer"

RFS-3-MSG_GET_NEGO_VER

3-Error

RFS Client [dec] get msg negotiated version failed. Error = [dec]

RFS ISSU client get msg negotiated version failed

-

"Enter the following commands: show issu fsm show issu ses and copy " "the error and send it to TAC. TAC team can contact the file-systems " "team to check why get message negotiated version failed"

RFS-3-MSG_INCOMP

3-Error

[chars]: msg_type [[dec]] under session [[dec]] is incompatible

The message types are incompatible under ISSU

-

"Enter the following command: \n\ show issu message types 110 \and copy the output and send it to TAC. TAC team can contact the \file-systems team to check why messages are incompatible"

RFS-3-RFS_RF_PROG_ERR

3-Error

Failed to send the bulk sync notification done. Error [dec].

The RFS RF client failed to send the final bulk sync \notification.

-

LOG_STD_ACTION

RFS-3-RFS_RF_PROG_NOT_SENT_ERR

3-Error

[chars].

The RFS RF client has error in sending client \progression.

-

LOG_STD_ACTION

RFS-3-RFS_BOOL_CREATE_ERR

3-Error

[chars].

The RFS RF client has error in creating watched boolean.

-

LOG_STD_ACTION

FLASH-3-DEVERR

3-Error

Error accessing the device : Device number = [dec] Error number = [dec]

Error was detected in accessing the device.

high-flash

"Report this error to your technical support representative."

FLASH-3-CISERR

3-Error

Error reading cis of Device [dec] : [dec] bytes read instead of [dec] bytes

Error was detected in reading the cis of device.

high-flash

"Report this error to your technical support representative."

FLASH-4-CLPDINT

4-Warning

Management interrupts are [chars] for pcmcia device in socket [dec]. [chars]

A faulty PCMCIA flash device might be generating spurious insert or remove interrupts continiously. The pcmcia controller will be set temporarily to disable interrupt generation and will be reenabled after a few seconds. This is to avoid storming CPU with spurious interrupts. If the alternate pcmcia device is

-

"Replace the pcmcia flash device with an alternate one"

FLASH-4-SIMM

4-Warning

System Flash Simms unequal. Simm1: [dec]M Simm2: [dec]M

The System has detected an unsupported flash configuration.

-

"Replace Flash Simms with equal sizes or remove Simm from System " "Flash Slot two."

FILESYS-5-DEV

5-Notice

PCMCIA flash card [chars] [chars]

A file system's status has changed. Follow any instructions provided with the message.

-

LOG_STD_NO_ACTION

FILESYS-5-IFLASH

5-Notice

Internal Flash [chars] [chars]

A file system's status has changed. Follow any instructions provided with the message.

-

LOG_STD_NO_ACTION

FILESYS-5-UNKNDEV

5-Notice

Unknown device [chars] [chars]

A file system's status has changed. Follow any instructions provided with the message.

-

LOG_STD_NO_ACTION

FILESYS-3-FLASH

3-Error

[chars] [chars] error [dec]

A file system error has occurred.

-

LOG_STD_SH_TECH_ACTION

FILESYS-4-RCSF

4-Warning

[chars] [dec] <[chars]>

A Running config sync file error has occurred.

-

LOG_STD_SH_TECH_ACTION

FILESYS-5-MISMATCH

5-Notice

[chars] device programming algorithm mismatch detected reformat is recommended

The flash device programming algorithm written to the device when the flash was formatted is different from what the current running software detected. A reformat of the flash device will solve the problem.

-

LOG_STD_NO_ACTION

FILESYS-3-IPC

3-Error

[chars] [chars]: IPC error [[chars]]

RFS operation failed due to an IPC error.

-

-

FILESYS-5-CFLASH

5-Notice

Compact flash card [chars] [chars]

A file system's status has changed. Follow any instructions provided with the message.

-

-

FILESYS-4-CLPDINT

4-Warning

Management interrupts are [chars] for pcmcia device in socket [dec]. [chars]

A faulty PCMCIA flash device might be generating spurious insert or remove interrupts continiously. The pcmcia controller will be set temporarily to disable interrupt generation and will be reenabled after a few seconds. This is to avoid storming CPU with spurious interrupts. If the alternate pcmcia device is

-

"Replace the pcmcia flash device with an alternate one"

PCMCIAFS-5-DIBERR

5-Notice

[dec] [chars]

The system cannot boot a image from the PCMCIA Flash disk because the Device Information Block is different. The Flash disk can be read by the router but will require formatting by the router before an image can be booted from it.

-

"Follow any instructions provided in the error " "message. Before storing a image in the Flash disk " "and trying to boot from this device enter the " "format command to format the flash disk from the " "router. Then copy the desired image to the Flash " "disk and then boot from this device."

PCMCIAFS-3-RESETERR

3-Error

PCMCIA disk [dec] [chars]

PCMCIA disk could not be reset while the system is initiated reload. This will cause a transient disk error disk timeout error when the ROMMON initialization code tries to reads the DIB. This is a transient error and the system will be able to access the disk and continue normal operation.

-

LOG_STD_NO_ACTION

PCMCIAFS-5-DFS_CLOSE_ERR

5-Notice

Error during close of the file [chars]. [chars]

An error occured during a file close operation.

-

"Enter the <CmdBold>fsck<NoCmdBold> <CmdArg>filesystem prefix:<NoCmdArg> " "command to check and attempt to repair the disk. If this does not " "fix the problem format the disk."

PCMCIAFS-4-DFS_FSCK_ERR

4-Warning

Error while running fsck on the file [chars].

Fsck is running in a loop while walking through the cluster chain of a file and has aborted.

ata-filesystem

LOG_STD_DDTS_TAC_DETAILS

DOSFS-5-DIBERR

5-Notice

[chars] [chars]

The system cannot boot a image from the Flash disk because the Device Information Block is different. The Flash disk can be read by the router but will require formatting by the router before an image can be booted from it.

-

"Follow any instructions provided in the error " "message. Before storing a image in the Flash disk " "and trying to boot from this device enter the " "format command to format the flash disk from the " "router. Then copy the desired image to the Flash " "disk and then boot from this device."

DOSFS-3-RESETERR

3-Error

[chars] [chars]

disk could not be reset while the system is initiated reload. This will cause a transient disk error disk timeout error when the ROMMON initialization code tries to reads the DIB. This is a transient error and the system will be able to access the disk and continue normal operation.

-

LOG_STD_NO_ACTION

DOSFS-5-DFS_CLOSE_ERR

5-Notice

Error during close of the file [chars]. [chars]

An error occured during a file close operation.

-

"Enter the <CmdBold>fsck<NoCmdBold> <CmdArg>filesystem prefix:<NoCmdArg> " "command to check and attempt to repair the disk. If this does not " "fix the problem format the disk."

DOSFS-4-DFS_FSCK_ERR

4-Warning

Error while running fsck on the file [chars].

Fsck is running in a loop while walking through the cluster chain of a file and has aborted.

ata-filesystem

LOG_STD_DDTS_TAC_DETAILS

ATA-6-ATA_STATUS_TIMEOUT

6-Information

Timeout occurred while querying the status of ATA device. Status returned :0x[hec] event: [dec]

A timeout occurred while querying the status of ATA device.

-

"Replace the new ATA device and retry the operation. " "If the problem persists " "1 Run 'show tech' command."

ATA-3-ATA_STATUS_ERROR

3-Error

Error occurred while querying the status of ATA device. Return: [dec] stat_reg: 0x[hec]

An error occurred while querying the status of ATA device. Device not responding

ata-filesystem

"Replace the new ATA device and retry the operation. " "If the problem persists " "1 Run 'show tech' command."

FILESYS_RFS-3-IPC

3-Error

[chars] [chars]: msg_type [[dec]] sub_type [[dec]]: IPC error [[chars]]

RFS operation failed due to an IPC error.

-

-

FILESYS_RFS-4-RFS_REQUEST_TIMEOUT

4-Warning

Timeout has occurred while executing the RFS request on file [chars] [[dec]].

A RFS request is sent to server from the client. While executing the request on the server side timeout has occurred at the client side.

-

LOG_STD_NO_ACTION

FLOWMON-4-ALERT_SCALE_LIMIT

4-Warning

Flow scale limit reached on LC. New Flows can get learnt when existing flows timeout

Generated when the Flow scale limit is reached on LC and new flow tries to learn

flomon

"NA"

FLOWMON-1-ALERT_CRI_SET

1-Alert

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-1-ALERT_CRI_CLEAR

1-Alert

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-2-ALERT_ERROR_SET

2-Critical

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-2-ALERT_ERROR_CLEAR

2-Critical

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-3-ALERT_NOTIFY_SET

3-Error

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-3-ALERT_NOTIFY_CLEAR

3-Error

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-4-ALERT_WAR_SET

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-4-ALERT_WAR_CLEAR

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-4-ALERT_INFM_SET

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-4-ALERT_INFM_CLEAR

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-4-ALERT_ALERT_SET

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-4-ALERT_ALERT_CLEAR

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-4-ALERT_EMERGENCY_SET

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set

flomon

"NA"

FLOWMON-4-ALERT_EMERGENCY_CLEAR

4-Warning

[[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars]

Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared

flomon

"NA"

FLOWMON-2-FLOW_THRESHOLD_EXCEEDED

2-Critical

Performance_Traffic_TCA[[chars]]: Exceeded configured [dec] current [dec]

Generated when the Flow monitoring threshold has crossed the configured limit

flomon

"NA"

FLOWMON-2-FLOW_THRESHOLD_RANGE_EXCEEDED

2-Critical

Performance_Traffic_TCA[[chars]]: Exceeded configured range[dec] [dec] current [dec]

Generated when the Flow monitoring threshold has crossed into the configured range limit

flomon

"NA"

FLOWMON-2-FLOW_ALERT

2-Critical

Performance_Traffic_ALERT[[chars]]: [[chars]]

Generated when the Flow monitoring alert are detected

flomon

"NA"

FMCORE-4-RACL_REDUCED

4-Warning

Interface [chars] routed traffic will be software switched in [chars] direction

TCAM resource contention prevents ACLs from being applied in the TCAM\n\ for this interface. The traffic on this interface will be sent to\n\ software in order that the ACLs can be applied.

fm

"The configured ACLs are too large to all fit in the hardware TCAM.\n\ Use mls tcam priority command to prioritize interfaces for hardware\n\ switching. Try and share the same ACLs across multiple interfaces\n\ in order to reduce TCAM resource contention."

FMCORE-6-RACL_ENABLED

6-Information

Interface [chars] routed traffic is hardware switched in [chars] direction

Earlier TCAM resource contention may have prevented ACLs from being applied in the TCAM for this interface. It has been enabled and traffic on this interface is hardware switched.

fm

"No need to take an action for this as it is an informational" "message not an error message."

FMCORE-2-VACL_FAILURE

2-Critical

Interface [chars] traffic will not comply with VACLs in [chars] directions

VACLs will not be applied on traffic for this interface due to TCAM\n\ resource contention.

fm

"The configured ACLs are too large to all fit in the hardware TCAM.\n\ Use mls tcam priority command to prioritize interfaces for hardware\n\ switching. Try and share the same ACLs across multiple interfaces\n\ in order to reduce TCAM resource contention."

FMCORE-2-ACL_FAILURE

2-Critical

Interface [chars] traffic will not comply with ACLs in [chars] directions

ACLs will not be applied on traffic for this interface due to TCAM\n\ resource contention.

fm

"The configured ACLs are too large to all fit in the hardware TCAM.\n\ Use mls tcam priority command to prioritize interfaces for hardware\n\ switching. Try and share the same ACLs across multiple interfaces\n\ in order to reduce TCAM resource contention."

FPD_MGMT-6-BUNDLE_DOWNLOAD

6-Information

Downloading FPD image bundle for [chars] card in [chars] ...

The system is downloading the field programmable device image bundle to the system main memory.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_TIME

6-Information

Estimated total FPD image upgrade time for [chars] card in [chars] = %TS.

The estimated total time for all FPD images to be upgraded is displayed for the indicated card.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_START

6-Information

[chars] FPD ID=[dec] image upgrade in progress for [chars] card in [chars].

The FPD image upgrade process has started. Do not interrupt the upgrade operation as any interruption could render the target card unusable. Avoid actions like removing the target card from the system powering off the system or using commands that can power-cycle the target card during the upgrade process.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_PASSED

6-Information

[chars] FPD ID=[dec] image in the [chars] card in [chars] has been successfully

The FPD image upgrade process has completed successfully for the indicated device.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-6-OVERALL_UPGRADE

6-Information

All the attempts to upgrade the required FPD images have been completed for [chars] card in [chars]. Number of successful/failure upgrades:

All the FPD image upgrades have completed for the indicated card.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_RETRY

6-Information

Attempting to recover from the failed upgrades ...

Because of an image upgrade failure the system will attempt again the upgrade operation for the same FPD image.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-6-PENDING_UPGRADE

6-Information

[dec] more FPD image upgrade operation will be required on [chars] in [chars] after additional power-cycle operation on the target card.

All upgrade operations have not completed and additional power-cycle operations are required before the upgraded or new FPD image will be applied to the system configuration. The message text indicates the number of pending upgrade operations that will be performed. More than one power-cycle operation might be required to complete the overall upgrade process.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-5-UPGRADE_ATTEMPT

5-Notice

Attempting to automatically upgrade the FPD images for [chars] card

The automatic FPD image upgrade feature is enabled with the <CmdBold> upgrade fpd auto<NoCmdBold> global configuration command. The system is currently upgrading an incompatible image version automatically.

spa-infra-fpd

"No action is required. The upgrade process can take a long time.The " "FPD_MGMT-6-UPGRADE_TIME message gives an estimate of the total " "upgrade time"

FPD_MGMT-5-CARD_POWER_CYCLE

5-Notice

[chars] card in [chars] is being power cycled for the FPD image upgrade to take effect.

The indicated card is being power cycled after the FPD image upgrade. This action allows the target card to be operational with the new upgraded FPD image or images.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-5-POST_UPGRADE_REMINDER

5-Notice

[chars] card in [chars] will require a [chars] for the FPD image upgrade to take effect.

The indicated card will require manual intervention after the FPD image upgrade. The specified operation is required for the upgraded FPD image to take effect.

spa-infra-fpd

LOG_STD_NO_ACTION

FPD_MGMT-4-BYPASS_AUTO_UPGRADE

4-Warning

The automatic FPD image upgrade feature is not enabled bypassing the image upgrade for [chars] card in [chars].

The automatic FPD image upgrade feature is not enabled. The incompatible image will not be automatically upgraded. The card will be disabled until the image is upgraded to a compatible version.

spa-infra-fpd

"Enable the automatic FPD image upgrade with the <CmdBold>upgrade fpd " "auto<NoCmdBold> global configuration command or use the <CmdBold>upgrade " "hw-module<NoCmdBold> privileged EXEC command for a manual upgrade " "operation. For more information about these commands refer to the " FPD_DOCUMENT_NAME "."

FPD_MGMT-4-UPGRADE_EXIT

4-Warning

Unexpected exit of FPD image upgrade operation for [chars] card in [chars].

The FPD image upgrade operation was interrupted by the physical removal of the card from the system or by the use of other commands that have interrupted the normal operation of the target card. The partial upgrade operation might have left the card unusable because of corrupted FPD images.

spa-infra-fpd

"If the card does not come up after reinserting into the system then " "perform the recovery upgrade operation by using the <CmdBold>upgrade " "hw-module<NoCmdBold> privileged EXEC command. With this command the " "system will attempt the reprogramming of the image to recover from the " "previous partial upgrade operation. For more information about " "performing a recovery upgrade operation refer to the " FPD_DOCUMENT_NAME "."

FPD_MGMT-4-VERSION_CHECK_ABORTED

4-Warning

FPD image version check operation has been aborted for [chars] card in [chars] because manual upgrade has already being started.

The FPD image version check operation required for the automatic upgrade feature is not being performed for the indicated card because the <CmdBold>upgrade hw-module<NoCmdBold> privileged EXEC command has already being executed. These two operations cannot be performed at the same time.

spa-infra-fpd

"If an automatic upgrade operation is required do not enter the " "<CmdBold>upgrade hw-module<NoCmdBold> privileged EXEC command for the " "manual upgrade while the target card is initializing. Enter the " "<CmdBold>show hw-module subslot fpd<NoCmdBold> command and ensure that " "the target card is displayed in the command output before proceeding " "with the manual upgrade."

FPD_MGMT-4-CFG_NOT_SYNCED

4-Warning

Failed to sync \[chars]\ command to standby: [chars]

A FPD configuration command failed to get synced to standby RP due to the indicated error condition. Usually this can happen if the standby RP hardware doesn't support the type of filesystem supported on the active one.

spa-infra-fpd

"Configure again the command with a filesystem that is supported on " "both standby and active RP. To find out if a specific filesystem is " "also supported on standby RP the <CmdBold>dir ?<NoCmdBold> command " "can be used to display a list of filesytem supported on both standby " "and active RP."

FPD_MGMT-3-INVALID_IMG_VER

3-Error

Invalid [chars] FPD ID=[dec] image version detected for [chars] card in [chars].

The indicated field programmable device contains an invalid version for the FPD image because the system was not able to extract this information from the indicated card. A failed upgrade attempt might have corrupted the FPD image identification on the device.

spa-infra-fpd

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-IMG_VER_NOT_FOUND

3-Error

FPD image version information is not available for [chars] card in [chars]. All the FPD images will be upgraded to recover from this error.

The FPD image version information for the indicated card is not available because the system was not able to extract this information for all the FPDs in the card. This could be the result of a corrupted FPD image from a power failure.

spa-infra-fpd

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-INCOMP_IMG_VER

3-Error

Incompatible [chars] FPD ID=[dec] image version detected for [chars] card

An incompatible FPD image version has been detected. The FPD image needs to be upgraded either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled.

spa-infra-fpd

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-MAJOR_VER_MISMATCH

3-Error

Major image version mismatch detected with [chars] FPD ID=[dec] for [chars] card

A major image version mismatch has been detected. This incompatibility will need to be resolved by doing an upgrade or downgrade operation either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled.

spa-infra-fpd

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-OPEN_FAILED

3-Error

Failed to open [chars] [chars]. Please make sure that the required file

The system cannot access the required file from the indicated URL.

spa-infra-fpd

"Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed."

FPD_MGMT-3-OUT_OF_MEMORY

3-Error

Could not allocate the required [dec] bytes of memory.

The system does not have enough free main memory to download the bundle file.

spa-infra-fpd

FPD_NO_FREE_MEMORY_STD_ACTION

FPD_MGMT-3-READ_ERROR

3-Error

Could not read the [chars] file.

The system cannot read the required file from the indicated URL.

spa-infra-fpd

"Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed."

FPD_MGMT-3-BNDL_WRONG_MAGIC_NUM

3-Error

The [chars] file contains a wrong magic number for the image bundle: [hex] expected [hex]. Please make sure that this is a valid FPD image [chars]

The indicated file might not be a valid FPD image bundle or package file for the target card or the file could be corrupted.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_WRONG_HDR_LEN

3-Error

The [chars] file contains wrong header length for the image bundle: [dec] bytes expected [dec] bytes. Please make sure that this is a valid

The indicated file might not be a valid FPD image bundle or package file for the target card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_WRONG_SIZE

3-Error

The [chars] file contains incorrect image bundle size: [dec] bytes expected [dec] bytes. Please make sure that this is a valid FPD image [chars] file

The indicated file might not be a valid FPD image bundle or package file for the target card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_CRC_CHECK_FAIL

3-Error

The [chars] file contains a corrupted image bundle - CRC mismatch: current value [hex] expected value [hex]. Please make sure that this is a valid FPD image [chars] file for card in [chars].

The file failed the CRC checking process. This failure indicates a corrupt FPD image bundle or package file.

spa-infra-fpd

"Try to download again the required package from the Cisco " "Software Center website as the indicated one might be corrupted. " "If the problem persists copy the error message exactly as it appears " "and gather the output of the <CmdBold>show hw-module subslot fpd" "<NoCmdBold> <CmdBold>show upgrade fpd table<NoCmdBold> and <CmdBold>" "show upgrade fpd file<NoCmdBold> <CmdArg>fpd-pkg-url<NoCmdArg> commands " "then contact your technical support representative with the gathered " "information."

FPD_MGMT-3-BNDL_CARD_TYPE_MISMATCH

3-Error

The [chars] file does not contain the card type [hex] in the image bundle

The image bundle in the indicated file does not contain a correct card type value for the target card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_NAME_PREFIX_MISMATCH

3-Error

The [chars] file contains a bundle name prefix [chars] that does not match

The content of the selected FPD image bundle does not match its filename.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INCOMP_BNDL_VER

3-Error

The selected [chars] file contain an image bundle that has a version number that is incompatible for this IOS release - [chars]. Selected version = [dec].[dec] minimum compatible version = [dec].[dec]. Please make sure that this is a valid FPD image [chars] file for card in [chars]. The SPA type is [chars].

The version of the selected FPD image bundle does not contain a valid version number that is compatible for the IOS release. The major version number should be the same and the minor version number should be at least equal to the minimal required version.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-MISSING_IMAGE

3-Error

Could not find the required [chars] image FPD ID=[dec] and FPD version=[dec].[dec] compatible with HW version=[dec].[dec] from the [chars]-fpd.bndl bundle in [chars]

The indicated FPD image bundle or package file might not be the correct one. IF this is a FPD image package file then an incompatible package file might have been renamed with a filename that matched with the one that the system is expecting for this Cisco IOS software release. You should never rename an FPD image package file name.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_MAJOR_VER

3-Error

The selected FPD image for upgrade contains wrong FPD image major version number = '[dec]' expected number = '[dec]' for [chars] FPD ID [dec].

The file used for upgrade might not be a valid FPD image bundle or package file for the card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_MAGIC_NUM

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong magic

The indicated file might not be a valid FPD image bundle or package file for the card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_HDR_LEN

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong header

The indicated file might not be a valid FPD image bundle or package file for the card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_DATA_LEN

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong data

The indicated file might not be a valid FPD image bundle or package file for the card.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-IMG_CRC_CHECK_FAILED

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file is corrupted - CRC

The image failed the CRC checking process this indicates a corrupt FPD image bundle or package file.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-FPD_UPGRADE_FAILED

3-Error

[chars] FPD ID=[dec] image upgrade for [chars] card in [chars] has FAILED.

The FPD image upgrade process has failed for the indicated device.

spa-infra-fpd

"Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "<CmdBold>show hw-module subslot fpd<NoCmdBold> and contact your " "technical support representative with the gathered information."

FPD_MGMT-3-FPD_UPGRADE_CANCELED

3-Error

Rest of the FPD upgrade sequence for [chars] card in [chars] has been canceled due to upgrade failure with [chars] FPD ID=[dec] image.

The FPD image upgrade process for additional FPD images has been canceled due to upgrade error in the indicated device.

spa-infra-fpd

"Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "<CmdBold>show hw-module subslot fpd<NoCmdBold> and contact your " "technical support representative with the gathered information."

FPD_MGMT-3-SEND_IMG_FAILED

3-Error

[chars] FPD ID=[dec] image for [chars] card in [chars] has failed to be sent

The FPD image was not able to be sent for the upgrade operation. The system might be too busy to handle this operation. The affected card will be disabled by this failure.

spa-infra-fpd

"Wait until the system load is lower to try again with the manual upgrade " "procedure by using the <CmdBold>upgrade hw-module<NoCmdBold> privileged " "EXEC command. If the symptom persists copy the error message " "exactly as it appears and gather the output of the <CmdBold>show " "tech-support<NoCmdBold> command and contact your technical support " "representative with the gathered information."

FPD_MGMT-3-IMG_DATA_UNCOMPRESS_ERROR

3-Error

Could not uncompress [chars] FPD image for [chars] in [chars].

An error has been detected during the uncompress operation of the compressed FPD image data.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BUNDLE_EXTRACT_ERROR

3-Error

Cannot extract the [chars] bundle from [chars] - [chars]

Bundle file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-PKG_VER_FILE_EXTRACT_ERROR

3-Error

Cannot extract the [chars] version file from [chars] - [chars]

Package version file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INVALID_PKG_FILE

3-Error

The indicated file [chars] is not a valid FPD image package file - [chars]

The file format does not appear to be a valid FPD image package.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INVALID_PKG_FILE_SIZE

3-Error

The indicated file [chars] does not have a valid FPD image package

The file size of the indicated FPD image package does not meet the required minimum size. The file is too small to be a valid FPD image package file.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-READ_BNDL_HDR_ERROR

3-Error

Failed to read the FPD bundle header from [chars] file.

The indicated file might not be a valid FPD image bundle or package file.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INVALID_IMAGE_SIZE

3-Error

The [chars] FPD image from [chars] file does not have a valid image size: expected size = [dec] bytes actual size = [dec] bytes.

The size of the indicated FPD image does not have the expected size. The FPD image bundle or package might not be a valid file.

spa-infra-fpd

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-MISSING_DEV_INFO

3-Error

Could not find [chars] FPD ID=[dec] in the list of FPD IDs populated

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-MISSING_BUNDLE_ENTRY

3-Error

Failed to find a matching entry in the programmable device bundle information table for [chars] in [chars]. Card type or HW version [dec].[dec]

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-CLOSE_FAILED

3-Error

Failed to close [chars] file.

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-UNKNOWN_BNDL_HDR_FORMAT

3-Error

Unknown header format version: [hex]

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-INVALID_UPGRADE_RESULT

3-Error

Invalid upgrade result '[dec]' received for the FPD image upgrade of [chars] FPD ID=[dec] for [chars] card in [chars].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-TOO_MANY_FPD_ENTRIES

3-Error

Too many FPD entries for the FPD Bundle Info Table. Required number of entries = [dec] maximum number of entries allowed = [dec].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-DUPLICATE_UPGRADE_RESULT

3-Error

Upgrade result already received for the FPD image upgrade of FPD ID [dec] for [chars] card in [chars].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-UPGRADE_LIST_FULL

3-Error

Could not add a new entry in the FPD Management Upgrade List. No upgrade will be performed for the [chars] card in [chars].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-SW_ERROR

3-Error

NULL

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-IPC_FAILED

3-Error

Failed to send IPC message to [chars] in [chars] - [chars]

The system failed to send a message via IPC to the indicated card. The cause of the specific IPC failure is inicated in the message.

spa-infra-fpd

LOG_STD_ACTION

FPD_MGMT-3-PKG_FILE_SEARCH_FAILED

3-Error

FPD image package [chars] cannot be found in system's flash card or

By default if the <CmdBold>upgrade fpd path<NoCmdBold> <CmdArg>fpd-pkg-url<NoCmdArg> global configuration command is not configured then the system will try to locate the required FPD image package file from removable flash cards or disks that are accessible by the system for FPD upgrade. This message indicates that the system could not find the package file.

spa-infra-fpd

"Make sure that the indicated FPD image package file is copied into a " "flash card or disk that is accessible by the system then restart the " "FPD upgrade by reinsertion of the target card to the system or use of " "a system command to reload or power-cycle the target card."

FPD_MGMT-3-CARD_DISABLED

3-Error

[chars] card in [chars] is being disabled because of an incompatible FPD image version. Note that the [chars] package will be required if you want to perform the upgrade operation.

The indicated card contains an incompatible FPD image version and is being disabled to avoid operational problems with the existing Cisco IOS software. This can happen if the automatic upgrade feature has not been enabled with the <CmdBold>upgrade fpd auto<NoCmdBold> global configuration command or if the automatic upgrade operation failed to perform the required upgrade or because it could not find the necessary FPD image package file. The incompatible image will need to be upgraded in order for the system to enable the card.

spa-infra-fpd

"The FPD image upgrade can be performed automatically by making sure that " "the automatic upgrade feature is enabled with the <CmdBold>upgrade fpd " "auto<NoCmdBold> global configuration command and the necessary FPD image " "package file is located in the system's default filesystem e.g. disk0: "

FPD_MGMT-3-PKG_VER_MISMATCH_NOTE

3-Error

The FPD image package being used [chars] is not the right version for

The indicated FPD image package that is being used in FPD automatic upgrade does not contain the correct version information for the IOS version that is running in the system. This condition can occur if a different version of the FPD image package was renamed to match the filename that the IOS image is expecting to use. The upgrade operation will still be performed by trying to find the required FPD image from the renamed package file.

spa-infra-fpd

"If the upgrade operation fails because the required FPD image cannot be " "found with the renamed FPD image package replace the wrong package " "file with a valid one and perform the upgrade operation again."

FPD_MGMT-3-INVALID_IMG_FORMAT

3-Error

Invalid image format '[chars]' detected for FPD ID=[dec].

The selected FPD image to upgrade the indicated field programmable device does not have the right image format that can be used by the system to perform the upgrade operation.

spa-infra-fpd

"Please check if the FPD image package used in the upgrade is for the " "correct platform. This can be checked by using the <CmdBold>show upgrade " "fpd package default<NoCmdBold> privileged EXEC command."

FPD_MGMT-2-CREATE_FAIL

2-Critical

Couldn't create [chars].

The system does not have enough free main memory to create the specified resource.

spa-infra-fpd

FPD_NO_FREE_MEMORY_STD_ACTION

FPD_MGMT-5-POSTPONE_POWER_CYCLE

5-Notice

[chars] card in [chars] will be power cycled after bulk sync completion.

Currently Bulk sync is in Progress. Once the new standby reaches HOT state the indicated card will be power cycled to be operational with the new upgraded FPD image.

spa-infra-fpd

LOG_STD_NO_ACTION

FRATM-2-INTERNAL_CRITICAL

2-Critical

[chars]

-

-

LOG_STD_SH_TECH_ACTION

FRATM-3-INTERNAL_ERROR

3-Error

[chars]

-

-

LOG_STD_SH_TECH_ACTION

FRATM-4-INTERNAL_WARNING

4-Warning

[chars]

-

-

LOG_STD_SH_TECH_ACTION

FRATM-3-CONFIG_ERROR

3-Error

[chars]

-

-

LOG_STD_SH_TECH_ACTION

FRATM_RED-3-INTERNAL_ERROR

3-Error

[chars]

-

-

-

FRATM_RED-3-INTERNAL_CRITICAL

3-Error

[chars]

-

-

-

FTTM-3-ERROR

3-Error

[chars]

Full Ternary TCAM Manager Error

-

LOG_STD_SH_TECH_ACTION

GLBP-4-BADAUTH

4-Warning

Bad authentication received from [chars] group [dec]

Two routers participating in a Gateway Load Balancing Protocol group disagree on the valid authentication string.

-

"Use the glbp authentication interface command to repair the " "GLBP authentication discrepancy between the local system " "and the one whose IP address is reported."

GLBP-3-MISCONFIG

3-Error

Cannot add MAC address [enet] to interface [chars] - not supported

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

GLBP-6-STATECHANGE

6-Information

[chars] Grp [dec] state [chars] -> [chars]

The GLBP gateway has changed state

-

LOG_STD_NO_ACTION

GLBP-6-FWDSTATECHANGE

6-Information

[chars] Grp [dec] Fwd [dec] state [chars] -> [chars]

The GLBP forwarder has changed state

-

LOG_STD_NO_ACTION

GLBP-4-DUPADDR

4-Warning

Duplicate address [chars] on [chars] sourced by [enet]

The IP address in a GLBP message received on the interface is the same as the router's own IP address. This may be because of misconfiugration or because of a malfunctioning switch

-

"Check the configurations on all the GLBP routers and make sure that " "any switches you have are functioning properly."

GLBP-4-DUPVIP1

4-Warning

[chars] Grp [dec] address [chars] is already assigned to [chars] group [dec]

The GLBP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to a different GLBP group.

-

"Check the configuration on all GLBP routers."

GLBP-4-DUPVIP2

4-Warning

[chars] Grp [dec] address [chars] is already assigned on this interface

The GLBP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to this interface.

-

"Check the configuration on all GLBP routers."

GLBP-4-DUPVIP3

4-Warning

[chars] Grp [dec] address [chars] is already assigned to or overlaps with an address on another interface or application

The GLBP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to or overlaps with an address on another interface or application.

-

"Check the configuration on all GLBP routers."

GLBP-4-BADVIP

4-Warning

[chars] Grp [dec] address [chars] is in the wrong subnet for this interface

The GLBP virtual IP address contained in the Hello message cannot be learnt as it is not within a subnet configured on the interface.

-

"Check the configuration on all GLBP routers and ensure " "that the virtual IP address is within a configured subnet."

GLBP-4-DIFFVIP1

4-Warning

[chars] Grp [dec] active routers virtual IP address [chars] is different to the locally configured address [chars]

The GLBP virtual IP address contained in the Hello message from the Active router is different to that configured locally.

-

"Check the configuration on all GLBP routers."

GPRSFLTMG-4-AAAFAIL_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

A PDP Activation has been failed because of one of the \n\ following reasons: \n\\n\ 1. No RADIUS server present for Authentication - No RADIUS server is \n\ configured or configured RADIUS server is not reachable.\n\ 2. Authentication fail - Authentication failed for invalid username \n\ or password.\n\ 3. Missing PAP/CHAP in non-transparent mode - PAP/CHAP IE is missing in \n\ the packet in non-transparent mode.\n\ 4. Missing username - User name field is not present in the PDP \n\ activation Request sent.

gprs

"1. Check whether RADIUS server is configured properly and able to \n\ ping it.\n\ 2. Check whether RADIUS server is configured properly. \n\ For the other reasons copy and save the error message with the output \n\ of 'show running' command. and contact your technical support \n\ representative."

GPRSFLTMG-4-GTPv1AAAFAIL_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars]

A PDP Activation has been failed because of one of the \n\ following reasons: \n\\n\ 1. No RADIUS server present for Authentication - No RADIUS server is \n\ configured or configured RADIUS server is not reachable.\n\ 2. Authentication fail - Authentication failed for invalid username \n\ or password.\n\ 3. Missing PAP/CHAP in non-transparent mode - PAP/CHAP IE is missing in \n\ the packet in non-transparent mode.\n\ 4. Missing username - User name field is not present in the PDP \n\ activation Request sent.

gprs

"1. Check whether RADIUS server is configured properly and able to \n\ ping it.\n\ 2. Check whether RADIUS server is configured properly. \n\ For the other reasons copy and save the error message with the output \n\ of 'show running' command. and contact your technical support \n\ representative."

GPRSFLTMG-4-IPALLOCATIONFAIL_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

Failed to allocate IP address dynamically because of one of the \n\ following reason:\n\\n\ 1. a. DHCP/RADIUS server IP address has been wrongly configured in GGSN.\n\ b. DHCP/RADIUS server is reachable but the configuration to \n\ allocate IP address might be wrong. or \n\ c. Properly configured DHCP/RADIUS server is unreachable.\n\ 2. Dynamic IP allocation is disabled in the APN configuration .\n\ 3. Missing PAP/CHAP information from radius client in \n\ transparent mode - Username and Password is missing in the \n\ PDP Activation Request.

gprs

"1.a. Check whether the GGSN is conifugred with the valid DHCP/RADIUS \n\ server IP address.\n\ b. Check whether DHCP/RADIUS server is configured properly to \n\ allocate IP address .\n\ c. If the configurations are fine then check whether the server \n\ is reachable from GGSN.\n\ 2. Configure IP allocation pool as either DHCP proxy client or RADIUS \n\ client in the APN .\n\ If you could not solve the problem still contact your technical support\n\ representative with the error message you got."

GPRSFLTMG-4-GTPv1IPALLOCATIONFAIL_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars]

Failed to allocate IP address dynamically because of one of the \n\ following reason:\n\\n\ 1. a. DHCP/RADIUS server IP address has been wrongly configured in GGSN.\n\ b. DHCP/RADIUS server is reachable but the configuration to \n\ allocate IP address might be wrong. or \n\ c. Properly configured DHCP/RADIUS server is unreachable.\n\ 2. Dynamic IP allocation is disabled in the APN configuration .\n\ 3. Missing PAP/CHAP information from radius client in \n\ transparent mode - Username and Password is missing in the \n\ PDP Activation Request.

gprs

"1.a. Check whether the GGSN is conifugred with the valid DHCP/RADIUS \n\ server IP address.\n\ b. Check whether DHCP/RADIUS server is configured properly to \n\ allocate IP address .\n\ c. If the configurations are fine then check whether the server \n\ is reachable from GGSN.\n\ 2. Configure IP allocation pool as either DHCP proxy client or RADIUS \n\ client in the APN .\n\ If you could not solve the problem still contact your technical support\n\ representative with the error message you got."

GPRSFLTMG-4-QOSFAIL_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

QoS negotitaion/update has failed since resources not available.

gprs

"Contact your technical support representative with the error messages \n\ and the output of command 'sh gprs gtp status' ."

GPRSFLTMG-4-GTPv1QOSFAIL_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars]

QoS negotitaion/update has failed since resources not available.

gprs

"Contact your technical support representative with the error messages \n\ and the output of command 'sh gprs gtp status' ."

GPRSFLTMG-4-APNRELATEDERROR_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

PDP activation has failed due to one of the APN related problem :\n\ 1. APN not configured - The APN requested in the PDP Request is not\n\ configured in the GGSN router.\n\ 2. Subscribe mode on APN but selection mode field not verified.\n\ 3. Duplicate static IP address to access same APN.\n\ 4. Session already exists for a different APN.

gprs

"Check the APN configuration correspondingly. If that can't solve the \n\ problem get the output of 'sh run' and 'sh gprs access-point all' \n\ copy the error message exactly as it appears and report to your \n\ technical support representative."

GPRSFLTMG-4-GTPv1APNRELATEDERROR_PDPACTIVATIONFAIL

4-Warning

\ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars]

PDP activation has failed due to one of the APN related problem :\n\ 1. APN not configured - The APN requested in the PDP Request is not\n\ configured in the GGSN router.\n\ 2. Subscribe mode on APN but selection mode field not verified.\n\ 3. Duplicate static IP address to access same APN.\n\ 4. Session already exists for a different APN.

gprs

"Check the APN configuration correspondingly. If that can't solve the \n\ problem get the output of 'sh run' and 'sh gprs access-point all' \n\ copy the error message exactly as it appears and report to your \n\ technical support representative."

GPRSFLTMG-0-GPRS_SERVICE

0-Emergency

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

You get this error messages because of one of the following reasons :\n\ 1. Path fail - No echo message is received from the GSN peer \n\ and time out. \n\ 3. GGSN service up - GGSN service starts.\n\ 4. GGSN service down - GGSN service shutdown.\n\ 5. Primary Charging Gateway down - Primary charging gateway is not \n\ reachable or unconfigured.\n\ 6. Primary Charging Gateway up - Primary Charging gateway is up or \n\ its configured .\n\ 7. Secondary Charging Gateway up - Secondary Charging Gateway is up \n\ or its configured.\n\ 8. Secondary Charging Gateway becomes unreachable or unconfigured.

gprs

"Error messages with reasons 36 and 7 are informational.\n\ For error messages with the other reasons contact your technical \n\ supportrepresentative with the error message you got."

GPRSFLTMG-0-RESOURCE

0-Emergency

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

Available resources exhausted to continue GGSN service because of \n\ the following reasons :\n\ 1. Number of PDP reaches Limit.\n\ 2. Number of Network Initiated PDP reached percentage - Insuffient \n\ in GGSN.\n\ 3. Number of IP PDP regenerated PPP reaches limit.

gprs

"1. Check whether you can increase number of PDP that can be handled \n\ by GGSN.\n\ If the problem recurs contact your technical support representative \n\ with the error message you got and with the output of \n\ 'show gprs gtp status'."

GPRSFLTMG-4-MOBILITY

4-Warning

\ GSN: [inet] TID: %08x%08x APN: [chars] Username: [chars] Reason: [dec] [chars]

One of the following Mobility Related problem has occured :\n\ 1. MS GPRS Detached.\n\ 2. MS GPRS present.\n\ 3. MS not GPRS responding for network initiated PDP - MS does not \n\ respond for packets initiated by external network. \n\ 4. MS Refused for network initiated PDP.\n\ 5. IMSI unknown for network initiated PDP.

gprs

"If the problem recurs contact your technical support representative\n\ with the error message you got "

GPRSFLTMG-4-GTPv1MOBILITY

4-Warning

GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars]

One of the following Mobility Related problem has occured :\n\ 1. MS GPRS Detached.\n\ 2. MS GPRS present.\n\ 3. MS not GPRS responding for network initiated PDP - MS does not \n\ respond for packets initiated by external network. \n\ 4. MS Refused for network initiated PDP.\n\ 5. IMSI unknown for network initiated PDP.

gprs

"If the problem recurs contact your technical support representative\n\ with the error message you got "

GPRSFLTMG-4-CHARGING

4-Warning

\ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars]

You get this syslog message due to one of the following reasons :\n\ 1. Primary/Secondary Charging gateway configured/unconfigured.\n\ 2. GSN GTP' Transfer Failure - Failure in sending CDRs to \n\ Charging gateway configured.\n\ 3. GSN CGF Echo Request Failure/Restored - Failure/Success of \n\ Echo messages sent charging gateway to check the connectivity of \n\ the Charging gateway configured. \n\ 4. GSN CDR Capacity Full/Free - Status of GSN CDR buffer full/free \n\ the subsequent packet might be dropped if the buffer is full.\n\ 5. GSN CDR Discard Notification - a status whether the GSN CDRs are\n\ getting discard/buffered.

gprs

"1. This is informational .\n\ 2. Check whether the charging gateways are configured correctly \n\ and are active with the charging functionality. \n\ 3. If the configured charging gateway is up and reachable from the GSN \n\ check whether charging function is enabled in the gateway.\n\ 45. If you have configured "gprs char charging-send-buffer-size" with minimum bytes you may configure maximum bytes.\n\ \n\ If the problem recurs contact your technical support representative \n\ with the error message you got"

GTP-2-PDPACTIVATIONFAIL

2-Critical

GTP PDP activation/update failed GSN: [inet] TID: [hec][hec] Reason: [chars]

A PDP context activation failed

gprs

"If this message recurs contact your technical support representative."

GTP-2-GTPv1PDPACTIVATIONFAIL

2-Critical

GTP PDP activation/update failed GSN: [inet] TEID: [hec] Reason: [chars]

A PDP context activation failed

gprs

"If this message recurs contact your technical support representative."

GTP-2-GSNSERVICEUPDOWN

2-Critical

GSN service [chars] changed state to [chars]

SGSN service starts or shutdown

gprs

"If this message recurs contact your technical support representative."

GTP-0-PACKETPARSINGERROR

0-Emergency

\ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars]

A PDP context activation failed at the packet parsing state for one\n\ of the following reasons:\n\ 1. Mandatory IE is missing in the PDP .\n\ 2. Mandatory IE incorrect - Mandatory IE has invalid range of value.\n\ 3. Mandatory IE out of sequence - The Mandatory IEs are not in sequence.\n\ 4. Invalid message format.\n\ 5. Optional IE incorrect - Optional IE present in the packet has\n\ invalid range of value.\n\ 6. Version not support - The GGSN Node does not support the GTP\n\ version recieved.\n\ 7. Non-charging msg in charging path.\n\ 8. Charging msg in GTP path.\n\ 9. Unknown GTP message.\n\ 10.Message too short - GTP message received is too short to contain\n\ all expected inform IE.\n\ 11.Unexpected message seen.

gprs

"Copy the error message exactly as it appears and report to your\n\ technical support representative."

GTP-0-GTPv1PACKETPARSINGERROR

0-Emergency

\ GSN: [inet] TEID: [hec] APN: [chars] Reason: [chars]

A PDP context activation failed at the packet parsing state for one\n\ of the following reasons:\n\ 1. Mandatory IE is missing in the PDP .\n\ 2. Mandatory IE incorrect - Mandatory IE has invalid range of value.\n\ 3. Mandatory IE out of sequence - The Mandatory IEs are not in sequence.\n\ 4. Invalid message format.\n\ 5. Optional IE incorrect - Optional IE present in the packet has\n\ invalid range of value.\n\ 6. Version not support - The GGSN Node does not support the GTP\n\ version recieved.\n\ 7. Non-charging msg in charging path.\n\ 8. Charging msg in GTP path.\n\ 9. Unknown GTP message.\n\ 10.Message too short - GTP message received is too short to contain\n\ all expected inform IE.\n\ 11.Unexpected message seen.

gprs

"Copy the error message exactly as it appears and report to your\n\ technical support representative."

GTP-4-RECOVERYIEDIFF

4-Warning

\ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars]

GGSN has recieved PDP update request with different Recovery\n\ Information Element in the same path.

gprs

"Contact your technical support representative with the error messages\n\ you got."

GTP-6-PDP_PURGED

6-Information

\ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars]

PDP context purged because of PDP context idle timeout

-

"This is purely informational "

GTP-0-NORESOURCE

0-Emergency

\ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars]

Available resources exhausted to continue GGSN service because of\n\ the following reasons :\n\ 1. Number of pending signaling messages reaches limit.\n\ 2. Out of Memory - Insuffient in GGSN.\n\ 3. System failure - Permenant system failure has occured.

gprs

"1. Check whether you can increase number of PDP that can be handled\n\ by GGSN.\n\ If the problem recurs contact your technical support representative\n\ with the error message you got and with the output of\n\ 'show gprs gtp status'."

GPRSFLTMG-0-GTPv1NORESOURCE

0-Emergency

\ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars]

Available resources exhausted to continue GGSN service because of\n\ the following reasons :\n\ 1. Number of pending signaling messages reaches limit.\n\ 2. Out of Memory - Insuffient in GGSN.\n\ 3. System failure - Permenant system failure has occured.

gprs

"1. Check whether you can increase number of PDP that can be handled\n\ by GGSN.\n\ If the problem recurs contact your technical support representative\n\ with the error message you got and with the output of\n\ 'show gprs gtp status'."

GPRSFLTMG-0-NOPROCESS

0-Emergency

\ [chars]

A Process could not be started

-

"Please contact your technical support representative \n\ with the error message you got and with the output of \n\ 'show gprs gtp status'."

GPRSFLTMG-0-GPRS_DHCP

0-Emergency

\ [chars]

Two reasons for this error message\n\ 1. DHCP Client failed to get started this could be because of malloc\n\ failures.\n\ 2. GPRS DHCP Process failed to start

gprs

"If this error message is seen it is recommended not to use this \n\ GGSN for PDP session establishment with SGSN with dynamic IP request.\n\ Check the available memory in the box and for the first reason try \n\ to get 'debug dhcp detail' before the failure.\n\ Contact your technical support representative with the error \n\ message you got."

GTP-3-INCOMPLETECONFIG

3-Error

\ APN: [chars] Reason: [chars]

A required configuration is missing

gprs

"Please make sure the missing commands are configured"

GVRP-6-MODECHANGE

6-Information

The operating mode is changed to [chars] mode on interface [chars].

As a result of protocol negotiation the operating mode changed to the specified mode on the specified interface.

gvrp

LOG_STD_NO_ACTION

GVRP-3-ENABLE_FAILED

3-Error

GVRP can't be enabled because [chars]

GVRP can't be enabled for some reason.

gvrp

"Action may be taken according to the given " "reason. If for instance the problem is " "due to lack of memory the user should " "add more memory to his system."

GVRP-3-SUBSYS_INIT_FAILED

3-Error

GVRP subsystem failed in initialization[chars] and GVRP won't

This is extremely unlikely to occur on a customer device. If it does occur the cause is most likely due to the lack of memory so the software failed to create data structures. User should see many

gvrp

"Most likely the system has crashed by then " "if the problem is due to lack of memory. " "If the system miraculously came up then" "user can run <CmdBold>show memory summary" "<NoCmdBold> to check the memory usage. " "Please contact the TAC with the output of " "<CmdBold>show memory summary<NoCmdBold> " "<CmdBold>show version<NoCmdBold> and " "<CmdBold>show run<NoCmdBold> and the " "associated syslog messages from the time " "of the problem."

GVRP-3-HA_INIT_FAILED

3-Error

GVRP High Availability subsystem fails to be initialized and hence GVRP won't support HA stateful switchover.

Either GVRP CF client or GVRP RF client fails to be initialized.

gvrp

"Enter the " "<CmdBold>show redundancy clients<NoCmdBold> " "and <CmdBold>show checkpoint clients<NoCmdBold> to " "find out which client is not initialized."

GVRP-3-ADD_REGISTRY_FAILED

3-Error

GVRP subsystem fails to add callback function [chars]

Other subsystem must have mistakenly add its own callback functions. This syslog is for debugging purpose.

gvrp

LOG_STD_NO_ACTION

SYS-4-GD_DATAUNRELIABLE

4-Warning

Update to memory leak detector on free of 0x[hec] failed CLI output is unreliable\n

managed chunk malloc to store the range that is freed while memory leak detector is in progress failed. Hence memory leak detector will not be updated of this free and this can be reported as leak which is false.

mem

"Ignore the output of \"show memory debug leaks..\" if system is in low " "memory condition else perform a bug toolkit search on the web for " "existing bugs related to this error message if none found contact TAC " "for this problem providing \"show version\" and " "\"show memory statistics\" output."

SYS-3-GD_STACKERR

3-Error

Unknown stack. Process: [chars]\n

An internal error occurred when running the memory leak detector

mem

"Copy the error message exactly as it appears on the console or in the" " system log and look up the message in the Bug Toolkit at:" " http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you are" " unable to resolve the issue using Bug Toolkit please issue a" " \"show tech\" and contact your technical support representative" " with the gathered information."

SYS-4-FREEMEMLOW

4-Warning

Free Memory has dropped below low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-5-FREEMEMRECOVER

5-Notice

Free Memory has recovered above low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the free memory in that pool is now above the configured low-memory limit.

-

"No action is required"

SYS-2-MALLOCFAIL

2-Critical

Memory allocation of [dec] bytes failed from [hex] alignment [dec] \n Pool: [chars] Free: [dec] Cause: [chars] \nAlternate Pool: [chars] Free: [dec] Cause: [chars] \n

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error may have exhausted or fragmented the router's memory.

mem-suspect

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representativeand provide the representative with the gathered information. " "Otherwise you may need to add more memory or reduce the number of " "features you are trying to support."

SYS-2-MUTEXLOCKFAIL

2-Critical

pthread_mutex_lock failed for [chars]

The thread failed in pthread_mutex_lock while trying to acquire a mutex.

mem-suspect

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-NOMEMORY

2-Critical

No memory available for [chars] [dec]

An operation could not be accomplished because of a low-memory condition. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

mem-suspect

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a configuration that has more memory."

SYS-3-CRITMEM

3-Error

[chars]

An attempt to allow or disallow a process from using memory that has been reserved for critical purposes has failed. The location of the failure is specified in the error message. This condition could possibly be caused by a software error.

mem-suspect

"Copy the error message and the traceback messages exactly as they appear " "on the colsole or in the system log contact your technical support " "representative and provide the representative with the gathered " "information."

SYS-2-GETBUFFFAIL

2-Critical

[chars] buffer allocation [dec] bytes failed from [hex]

-

-

-

SYS-6-NOBRIDGE

6-Information

Bridging software not present

Your system is not configured to be a bridge.

none

"Configure the bridging software."

SYS-3-SOCKUNKN

3-Error

Unknown socket protocol [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-HARIKARI

3-Error

Process [chars] top-level routine exited

An internal software error occurred

Determine the component from the process name displayed in the error message.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPID

2-Critical

Bad pid [dec] for tty [t-line]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-MGDTMRRUN

3-Error

TTY[t-line]: Managed Timers [chars] still running

One or more managed timers for a TTY that is deleted are still running.

-

LOG_STD_ACTION

SYS-0-USERLOG_EMERG

0-Emergency

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-1-USERLOG_ALERT

1-Alert

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-2-USERLOG_CRIT

2-Critical

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only. "

SYS-3-USERLOG_ERR

3-Error

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-4-USERLOG_WARNING

4-Warning

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-5-USERLOG_NOTICE

5-Notice

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-6-USERLOG_INFO

6-Information

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-7-USERLOG_DEBUG

7-Debug

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-3-MSGLOST

3-Error

[dec] messages lost because of queue overflow

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-REGEXP

4-Warning

[chars].

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-5-RESTART

5-Notice

System restarted --\n[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SCHEDULED_RELOAD

5-Notice

Reload requested for [chars]

A scheduled reload has been requested for the router.

none

"No action is required."

SYS-5-SCHEDULED_RELOAD_CANCELLED

5-Notice

Scheduled reload cancelled at [chars]

A scheduled reload that was requested for the router has been cancelled.

none

"No action is required."

SYS-5-RELOAD

5-Notice

Reload requested[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SWITCHOVER

5-Notice

Switchover requested[chars]

A switchover was requested.

none

"This is a notification message only. No action is required."

SYS-4-RELOAD_ATTEMPT

4-Warning

Attempt via SNMP failed system shutdown not configured

SNMP cannot be used to reload the router unless this functionality has been previously configured. This message reports that an attempt to reload the router failed because SNMP reloads are not currently configured on the router.

none

"This is a notification message only. No action is required."

SYS-3-CFG_AT_RELOAD

3-Error

System reloading unable to complete startup configuration update

Startup configuration updation is already in progress and reload has been called either from interrupt level or with all interrupts disabled. Reload can not suspend to let startup configuration updation get completed. Startup configuration may get corrupted.

none

"This is a notification message only. No action is required."

SYS-4-DUAL_MESSAGE

4-Warning

SNMP system message request [dec] denied because of pending job

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-5-CONFIG

5-Notice

Configured from [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_I

5-Notice

Configured from [chars] by [chars]

The write of the system running configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_RESOLVE_FAILURE

4-Warning

System config parse from [chars] failed

The configuration file from the URL specified in the error message could not be read.

-

"Enter the <CmdBold>no service config<NoCmdBold> " "command to disable autoloading of configuration files " "OR investigate why the tftp load is failing."

SYS-5-CONFIG_NV

5-Notice

Nonvolatile storage configured from [chars]

The configuration was written successfully.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_NV_I

5-Notice

Nonvolatile storage configured from [chars] by [chars]

The write of the nonvolatile configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-CONFIG_NV_DATA

3-Error

Variable [chars] not set properly in the routine [chars].

The write of the nonvolatile configuration failed because an internal variable was not set properly.

-

"If this messages occurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_NEWER

4-Warning

Configuration from version [dec].[dec] may not be correctly understood

The software detected that the configuration saved in memory was written by a newer version of software. There might be commands saved in memory that are not implemented by the older software version.

none

"Examine all the messages printed while the router was " "booting. For each message about an unknown command determine " "whether that feature is required. If so upgrade to a " "newer version of software that supports that feature."

SYS-4-CONFIG_NOLOCK

4-Warning

The configuration could not be locked

A software error occurred.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SYS-3-CONFIG_NO_PRIVATE

3-Error

No space remaining to save private config

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-CONFIG_NV_OVERRUN

4-Warning

Non config data present at the end of nvram is corrupted

The software detected that the configuration saved into nvram has overlaid a part of the nvram occupied by non config data files.Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_TRUNCATE

4-Warning

Truncated configuration to %ld bytes from %ld bytes

The software detected that the configuration saved into nvram has been truncated. There was not enough space to save the compressed configuration.

-

"Save the configuration to flash if the platform supports " " \"boot config\" command."

SYS-4-CONFIG_NV_NEED_OVERRUN

4-Warning

Non config data present at the end of nvram needs to be overwritten to fit the configuration into nvram

The software detected that the non config data files occupying the end of nvram need to be overwritten to fit the configuration. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_NEED_TRUNCATE

4-Warning

Configuration needs to be truncated to fit into nvram

The software detected that the configuration is to be truncated to fit in the nvram. There was not enough space to save the compressed configuration

-

"Save the configuration to flash if the platform supports " "\"boot config nvbypass\" command."

SYS-4-NV_BLOCK_INITFAIL

4-Warning

Unable to initialize the geometry of nvram

The software detected that it failed to initialize the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload. This may happen when the entire nvram is packed with the configuration and the newer version of software which supports this feature could not find the minimum room in the nvram to initialize block file system.

-

"Reduce the configurations in the nvram atleast by 2K"

SYS-7-NV_BLOCK_INIT

7-Debug

Initialized the geometry of nvram

Initialized the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

""

SYS-4-NV_CHKSUM

4-Warning

An nvram checksum is already in progress

An interrupt service routine attempted to perform a checksum on the nvram contents and found the resource in use.

nvram

-

SYS-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMINIT

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be initialized. reasons are not clear.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent data some corruption.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CONFIG_DOWNFAIL

2-Critical

Generated configuration not backward compatible

The router has been configured to generate nonvolatile memory using the commands of an older software version. The current configuration of the router contains a command that cannot be saved using only the older command set.

none

"Allow the router to save the configuration using the command set of " "the current software version or remove the commands that cannot be " "saved using the older command set."

SYS-5-OUTSETUP

5-Notice

Configuration file [chars] accepted aborting setup

A configuration was accepted over the network so the setup session will be aborted.

none

"This is a notification message only. No action is required."

SYS-3-BADLINKTYPE

3-Error

* Unexpected linktype [dec]

* A software error occurred.

udp

* "Copy the error message exactly as it appears and report it to your " * "technical support representative."

SYS-2-SIGNUM

2-Critical

Process aborted on invalid signal signum = [dec].

An attempt was made to send an invalid signal to another process.

-

"If this message occurs more than once report this message " "to your technical support representative."

SYS-3-CPUHOG

3-Error

Task is running for [dec]msecs more than [dec]msecs [dec]/[dec]

The indicated process ran too long without relinquishing the processor. Each process should run for a small amount of time and then relinquish the CPU so that other processes can run. This problem can be caused by many things like traffic or system load hardware or operational configuration a configuration change initialization of many interfaces cards or ports for example a high momentary error rate a sustained abnormal

If this error occurs in conjunction with a TIMERHOG message \n\ report the two errors together and use the component obtained \n\ for the TIMERHOG message.

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representative and provide the representative with the gathered information."

SYS-2-WATCHDOG

2-Critical

Process aborted on watchdog timeout process = [chars].[chars]

The indicated process ran for too long without relinquishing control. The system killed it as a runaway process.

-

-

SYS-3-TIMERHOG

3-Error

Timer callback ran long PC = [hec].

The indicated callback routine ran for too long without relinquishing the processor.

Determine the component from the callback routine address displayed in\n\ the error message. Use Topic to search for a similar DDTS. If you \n\ find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-6-STACKLOW

6-Information

Stack for [chars] [chars] running low [dec]/[dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-GREEDY_REGEXP

4-Warning

[chars] while processing the input regular expression. Aborting processing use alternate regular expression. Input regular expression: \[chars]\

Regular expression processing limitation: Certain regular expressions require huge stack space for processing or can lead to processing timeouts. We abort processing such regular expressions and print this message to avoid stack overflow/unexpected reload.

os

"The regular expression specified leads to stack overflow/processing " "timeout of the indicated process. Recommended to use a different " "regular expression."

SYS-1-CPURISINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr: [dec]%%/[dec]%%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped.

-

"Enter the <CmdBold>show processes CPU<NoCmdBold>" " command to determine the CPU hogging process" " that is causing this condition and if possible" " disable the activity that is causing the" " CPU hog condition so that CPU" " utilization is reduced."

SYS-1-CPUFALLINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr [dec]%%/[dec]%%.

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required."

SYS-2-INPUTQ

2-Critical

INPUTQ set but no IDB ptr=[hec]

This message is issued when an attempt is made to alter the input queue count for a packet that should not be counted.

-

-

SYS-6-BADSHAREINFO

6-Information

[chars] packet [hec] has a zero reference count freeing pid = [hec] \n\ freeing pc = [hec] [chars].

Provides additional information about original freer of packet.

-

-

SYS-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[hec]

A reference count is used to track the usage of many data structures. A function increments the count when it begins to use a structure and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be negative which means that the data structure will not be freed until the system is reloaded.

-

-

SYS-2-CFORKLEV

2-Critical

Process creation of [chars] failed at level [dec].

An internal software error occurred.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKMEM

2-Critical

Process creation of [chars] failed no memory.

Insufficient memory was available to create a process either while trying to support additional features or due to a memory leak.

mem-suspect

"A memory leak may be the cause if the system has been running for a " "while without changing its configuration. If you suspect a leak then " "copy this message exactly as it appears and report it to your technical " "support representative. Otherwise ensure that more memory is available " "to support the additional features."

SYS-2-CFORKBADFUNCT

2-Critical

Can't create process with start address = [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPROCESS

3-Error

Bad process ID [dec] when [chars] process table

An internal software error occurred.

os-scheduler

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INSCHED

2-Critical

[chars] within scheduler

-

Determine the component from the stack trace displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem.

-

SYS-2-NOTIOSTASK

2-Critical

[chars] from outside IOS task context

An IOS reschedule request was made from code that is not running in the context of an IOS task -- from an interrupt handler the scheduler itself or a service pthread within the IOS process.

Determine the component from the stack trace displayed in the\n\ error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INTSCHED

2-Critical

'[chars]' at level [dec]

The scheduler was entered from an interrupt service routine ISR.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

-

SYS-3-PROCSEMFAIL

3-Error

Process semaphore creation for preemptive processes failed.

Creation of process function semaphore to protect the critical section of process create routine failed. The semaphore creation can fail if there isnt enough chunk memory to create the event structure.

os

-

SYS-2-NOBLOCK

2-Critical

[chars] with blocking disabled.

A process aattempted to relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

-

SYS-2-BLOCKHUNG

2-Critical

Task hung with blocking disabled value = 0x[hec].

The indicated process has exceeded the time limit for which it may relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

"This message may be a result of high loads. If it recurs " "copy the text exactly as it appears and report it along " "with the associated stack trace to your technical support " "representative."

SYS-2-NOTDEAD

2-Critical

Killing process [chars] pid [dec] again

An internal software error occurred.

os-scheduler

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOPROCESS

2-Critical

No such process [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-IMMORTAL

2-Critical

Attempt to shut down management process [dec] [chars].

An attempt was made to shut down the specified management process. Management processes must not be shut down as long as the\n\ router remains up.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the process_kill.

-

SYS-2-SIGPENDING

2-Critical

Multiple Signals are sent to a process [dec]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADSTACK

2-Critical

Process [chars] has trashed stack old size [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-6-MTRACE

6-Information

[chars]: addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC

This is an auxiliary message to several memory-related messages. It provides the address of the memory block and the calling program counter for the last eight blocks allocated and for the last eight blocks freed.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of a previously printed error message."

SYS-6-BLKINFO

6-Information

[chars]blk [hec] words [dec] alloc [hec] [chars] dealloc [hec] rfcnt [hec]

This is an auxiliary message to several memory-related messages. It provides a formatted display of some of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-MEMDUMP

6-Information

[hex]: [hex] [hex] [hex] [hex]

This is an auxiliary message to several memory-related messages. It provides a raw display of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-PROCINFO

6-Information

Process [chars] just finished executing

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

-

"Copy this messages exactly as it appears and report it along with " "the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your " "technical support representative."

SYS-6-TESTINFO

6-Information

Scheduler test [hex] for [chars] just executed

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

Determine the component from the address of the scheduler test routine\n\ displayed in the error message.\n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy this message exactly as it appears and report it along with the " "SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical " "support representative."

SYS-3-BADBLOCK

3-Error

Bad block pointer [hec]

A block of memory at the indicated location is corrupt. An internal check of memory block pointers indicates an inconsistency.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to auotmatically reload then the router will " "need to reloaded manually."

SYS-3-BADMAGIC

3-Error

Corrupt block at [hec] magic %08x

The free memory pool is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADREFCOUNT

3-Error

Bad reference count at [hec] refcount [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-3-OVERRUN

3-Error

Block overrun at [hec] red zone %08x

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-FREEBAD

2-Critical

Attempted to free memory at [hec] not part of buffer pool

An attempt was made to free memory but the request could not be completed due to an invalid memory data structure

-

-

SYS-2-FREEFREE

2-Critical

Attempted to free unassigned memory at %lx alloc %lx dealloc %lx

An attempt was made to free memory at the indicated location. The memory could not be freed because it was not allocated.

-

-

SYS-3-INVMEMINT

3-Error

Invalid memory action [chars] at interrupt level

This message indicates that a memory allocation or deallocation was attempted from an interrupt handler.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-INVMEMPID

3-Error

Invalid pid [dec] in block: [hec]

There has been attempt to allocate memory on behalf of an invalid process.

mem

-

SYS-3-MEMSEMFAIL

3-Error

Mempool semaphore creation failed for [chars]

This message indicates that the semaphore creation for the specified mempool failed.

-

-

SYS-3-INUSEFREE

3-Error

Block [hec] on free list [dec] in use

A memory management function attempted to allocate the indicated block from a list of free blocks. However the block was found to be already in use.

-

-

SYS-3-NZREFCNT

3-Error

Block [hec] on free list [dec] with refcount [dec]

A block of memory in the free pool is actually in use. The message indicates the number of processes using the memory block.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-WRONGFREELIST

3-Error

Block [hec] size [dec] on wrong free list [dec] [dec]

A freed buffer was placed on the wrong list of free buffers.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEMAGIC

3-Error

Corrupt free block at [hec] magic %08x

A block of memory at the indicated location is corrupt. An inconsistency was detected while checking the free memory area.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADPTRVAL

3-Error

Bad pointer value [chars] = [hec] in function [chars]

Corrupted pointer value is encountered.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEPTRS

3-Error

Bad [chars] pointer [hec] at [hec] [chars] = [hec]

A pointer in the block header at the indicated location is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-GETBUF

2-Critical

Bad getbuffer bytes= [dec]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

-

SYS-2-INPUT_GETBUF

2-Critical

Bad getbuffer bytes= [dec] for interface= [chars]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

LOG_STD_ACTION

SYS-2-INLIST

2-Critical

Buffer in list ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-INLIST1

2-Critical

Buffer in list ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED1

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPOOL

2-Critical

Attempt to use buffer with corrupt pool pointer ptr= [hec] pool= [hec]

An memory management function attempted an operation that could not be performed due to invalid memory pool descriptors.

-

-

SYS-2-BADPOOLMAGIC

2-Critical

Attempt to use pool pointer with corrupt header pool= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-WRONGPOOL

2-Critical

Buffer [hec] found in pool [hec] should be in pool [hec]

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-2-BADBUFFER

2-Critical

Attempt to use [chars] buffer as [chars] ptr= [hec] pool= [hec]

A hardware or software error occurred. An inconsistency was encountered while processing a packet buffer.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information."

SYS-2-QCOUNT

2-Critical

Bad [chars] [hec] count [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOTQ

2-Critical

[chars] didn't find [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-LINKED

2-Critical

Bad [chars] of [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SELFLINKED

2-Critical

Buffer [hec] linked to itself in free pool [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-ALREADYFREE

2-Critical

Buffer [hec] already in free pool [chars]

A block of memory at the indicated location is corrupt and/or has been erroneously freed twice.

os

"If this message recurs copy it exactly as it appears and the output " "of 'show buffer address <number>' for the given address as well as " "'show buffer pool <name> dump' for the given pool. Report it to your " "technical support representative."

SYS-2-LOWMEMPROC

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available processor memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak copy the message exactly as it appears and " "report it to your technical support representative. Otherwise you may " "need to add memory or reduce the number of features you are trying to " "support."

SYS-2-LOWMEMIO

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available IO memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak " "copy the message exactly as it appears and " "report it to your technical support representative. " "Otherwise you may need to add memory " "or reduce the number of features you are trying to " "support."

SYS-2-NOMEMFRGPROC

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous processor memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-NOMEMFRGIO

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous IO memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing " "copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-SPEC

2-Critical

Trying to set unknown special character [dec] to [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-ABRUPTTERM

3-Error

Abrupt termination of tty session for [chars] [t-line]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADDISP

3-Error

Bad disposal code [hec] in [chars]

An invalid status code has been passed to a buffer deletion routine. The buffer will be correctly returned to the free pool but will not be correctly counted in the per-protocol statistics.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NULLIDB

3-Error

Null IDB in [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-1-OVERTEMP

1-Alert

System detected OVERTEMPERATURE condition.\n Please resolve cooling problem immediately!\n

The environmental monitor detected a high-temperature condition.

none

"Make sure that the room temperature is not too high and that air flow " "to the card is not blocked. If this condition persists the " "environmental monitor might shut down the system. Call your technical " "support representative for assistance if necessary."

SYS-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADRESID

3-Error

Clock hardware returned bad residual [dec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPRINT

3-Error

Process has no associated tty in [chars].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-INTPRINT

3-Error

Illegal printing attempt from interrupt level.

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-OVFPRINT

3-Error

Overflow in [chars] chars [dec] buffer size [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NOELEMENT

3-Error

[chars]:Ran out of buffer elements for enqueue

The process was unable to enqueue data as it ran out of buffer elements.

-

"Copy the error message exactly as it appears also get the " "output of show buffers and report it to your technical support " "representative."

SYS-6-CLOCKUPDATE

6-Information

System clock has been updated from [chars] to [chars] configured from [chars] by [chars].

This message indicates that the system clock has been modified.

-

"This is informational message."

SYS-5-TABLEERR

5-Notice

[chars] table [chars] damaged: [chars].

An internal table entry became corrupt.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-3-BADTREEPARAM

3-Error

Bad parameter for [chars] passed to tree library function.

This message indicates that a pointer passed to a tree library function is invalid.

-

LOG_STD_SH_TECH_ACTION

SYS-2-BADLIST

2-Critical

Regular expression access check with bad list [dec]

This message indicates that a pointer to an access list is invalid.

-

"The event that caused this message to be issued should not " "have occured. It can mean that one or more data structures " "have been overwritten. If this message recurs and you decide " "to report it to your technical representative you should " "copy the text of the message exactly as it appears and " "include the associated stack trace." "\n\n Since access list corruption may have occurred " "a technical representative should verify that access " "lists are functioning corectly."

SYS-2-SNMP0IDX

2-Critical

Attempt to [chars] snmpidb with if_index of 0

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-SNMP_WRITENET

4-Warning

SNMP WriteNet request. Writing current configuration to [inet]

SNMP is writing the current configuration to a network host.

none

"These are notification messages only. No action is required."

SYS-4-SNMP_HOSTCONFIGSET

4-Warning

SNMP hostConfigSet request. Loading configuration from [inet]

SNMP is reading the host configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-SNMP_NETCONFIGSET

4-Warning

SNMP netConfigSet request. Loading configuration from [inet].

SNMP is reading the network configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-INVALID_IMAGE

4-Warning

Running invalid image for platform!

The software image being run is for a different hardware architecture. This problem can occur on a Cisco 1003 Cisco 1004 or Cisco 1005. The Cisco 1003 and Cisco 1004 use a different image from the Cisco 1005.

none

"Install the correct software image."

SYS-2-CHUNKBOUNDS

2-Critical

Could not find the sibling to allocate memory from. Chunk [chars] total free [dec] inuse [dec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBOUNDSIB

2-Critical

Error noticed in the sibling of the chunk [chars] Chunk index : [dec] Chunk real max : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKFREE

2-Critical

Attempted to free nonchunk memory chunk [hec] data [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKSIBLINGDEST

2-Critical

Attempted to destroy a sibling chunk [hec] [chars].

-

-

-

SYS-2-CHUNKSIBLINGS

2-Critical

Attempted to destroy chunk with siblings chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKPARTIAL

2-Critical

Attempted to destroy partially full chunk chunk 0x[hec] chunk name: \[chars]\.

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKBADMAGIC

2-Critical

Bad magic number in chunk header chunk [hec] data [hec] chunkmagic [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-6-INVALID_BOOTTIME

6-Information

Time since last reboot not available

This is an informational message for the user. The time taken for the router to come up after OIR is not available.

-

"No action required."

SYS-6-BOOTTIME

6-Information

Time taken to reboot after reload = %-4d seconds

This is an informational message for the user. This provides the time taken for the router to come up after reload or crash. The time is actually the difference between the last crash and a successive boot. If autoboot was not set and router is in rommon for a long time then the reload time shown could be large.

-

"No action required."

SYS-2-CHUNKBADREFCOUNT

2-Critical

Bad chunk reference count chunk [hec] data [hec] refcount [hec] alloc pc [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOMEMORY

2-Critical

* Could not allocate chunks for [chars]. No memory

* A software error occurred.

-

* "Copy the error message exactly as it appears and report it to " * "your technical support representative."

SYS-2-CHUNKEXPANDFAIL

2-Critical

Could not expand chunk pool for [chars]. No memory available

There is not enough processor memory left to grow this chunk pool.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADFREEMAGIC

2-Critical

Bad free magic number in chunk header chunk [hec] data [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOROOT

2-Critical

Root chunk need to be specified for [hec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINVALIDHDR

2-Critical

Invalid chunk header type [dec] for chunk [hec] data [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-CRASHINFOINITFAIL

3-Error

Crashinfo subsys initialization did not add registry \n\ crashinfo_get_default_file_name.\n

In order to figure out the device which the crashinfo writes to the crashinfo subsys has to add the registry crashinfo_get_default_file_name.

-

"Use Topic to search for a similar DDTS. If you find none write " "a DDTS for this problem. This SHOULD never happen - it is an " "indication of a bug elsewhere in the code."

SYS-2-CHUNKBADPOOLSIZE

2-Critical

Bad poolsize returned by the system : [dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINCONSIS

2-Critical

Inconsistant counters for chunk : [chars] total free [dec]/[dec] total sibs [dec]/[dec] total alloc [dec]/[dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADELESIZE

2-Critical

Chunk element size is more than 64k for [chars]

Chunk manager cannot function properly with big chunk elements

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-NULLCHUNK

2-Critical

Memory requested from Null Chunk

Chunk manager cannot allocate memory from NULL chunks

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNKSIBLINGSEXCEED

4-Warning

Number of siblings in a chunk has gone above the threshold. Threshold:[dec] Sibling-Count:[dec] Chunk:0x[hec] Name:[chars]

Number of siblings in a chunk with no header has gone above the default/configured threshold configured using <cmdBold>memory chunk siblings threshold<nocmdBold> <cmdArgs>count<nocmdArgs>

-

LOG_STD_SH_TECH_ACTION

SYS-1-CCA_SYS_ERR

1-Alert

CCA Detected System Error code = [dec]

CCA has detected a severe system software error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-2-CCA_INT_ERR

2-Critical

CCA Detected Logic Error code = [dec]

CCA has detected a severe internal logic error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-3-TIMERNEG

3-Error

Cannot start timer [hex] with negative offset [dec].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-MGDTIMER

3-Error

[chars][chars] timer = [hec].

This message indicates an error in a system timer. The problem can be caused either by software or by hardware.

-

-

SYS-3-DMPMEM

3-Error

%08x: %08x %08x %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-BOOT_MESSAGES

6-Information

Messages above this line are from the boot loader.\n

At least one informational or error message was printed by the boot loader.

-

"If the system image was loaded no action is recommended. If the " "system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-2-EXCEPTIONDUMP

2-Critical

System Crashed Writing Core....

The system has crashed because of an exception A core is being generated

-

LOG_STD_ACTION

SYS-3-LOGGER_FLUSHING

3-Error

System pausing to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system is paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_FLUSHED

3-Error

System was paused for %TE to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system was paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_DROPPED

3-Error

System dropped [dec] console debug messages.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

SYS-3-LOGGER_COUNT_STOP_CHUNK

3-Error

System cannot release chunk memory.\n

The system was not able to destroy a previously allocated chunk of memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-CHUNK_NO_EXMEM

3-Error

No handler to [chars] external memory.

An attempt was made to allocate or free a chunk of external memory but no handler for managing external memory was registered.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-READ_BOOTFILE_FAIL

6-Information

[chars] [chars].\n

A configured boot system command failed.

-

"If a system image was eventually loaded no action is recommended. If " "the system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-3-URLWRITEFAIL

3-Error

redirection url write failed '[chars]'

Redirection of output to URL failed.

-

"Check for free space on destination URL and retry."

SYS-6-READ_BOOTFILE_SKIP

6-Information

boot system [chars] command is skipped\n

A configured boot system command is skipped. Either the system experienced a crash while loading this image in the last attempt or the filename is not properly specified. Subsequent boot system commands will be tried

-

"Replace the failed boot system image with a good one. There could be " "various reasons that this specified image failed for example the image " "might be with a bad checksum."

SYS-6-USING_RESERVE_MEMORY

6-Information

Reserve memory is being used

The reserved memory is being used by the console

-

"The system is low in memory. The reserved memory will be " "used only by the console process. Please take a techsupport " "so that the reason for low memory can be found"

SYS-6-RESERVE_MEMORY_CREATED

6-Information

Reserve memory is being created

A portion of memory is reserved exclusively for console

-

"The console access is made available even in low memory " "condition. User can collect the details like tech-support " "for further diagnosis"

SYS-3-BAD_RESET

3-Error

Questionable reset of process [dec] on tty[t-line]\n

A process was reset without giving it a chance to clean itself up.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-DUP_TIMER

3-Error

Same tty[t-line] in linewatch_timers type [dec]

A tty appeared twice in a timer list where it should have only appeared once.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-LINEPROCDEAD

2-Critical

Killing process [chars] associated with line [dec]

A process associated with a tty line was killed by another process. The line may go dead

exec

"If this messages recurs copy it exactly as it appears " "and report it to your technical support representative."

SYS-3-HTIMER_EXPAND

3-Error

timer heap at 0x[hec] needed to expand but hasn't

A timer heap should have expanded but has not

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_INIT

3-Error

heap timer at 0x[hec] has not been initialized

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_STATE

3-Error

heap timer at 0x[hec] in state [dec]

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-MUNMAP

2-Critical

Could not return memory Neutrino via munmap at %lx size [dec] errno [dec]

Failued to unmap memory memory at the indicated location. The memory could not be unmapped because it was allocated via mmap.

-

-

SYS-2-MMAP

2-Critical

mmap failed for size [dec] bytes Caller PC 0x[hec] errno [dec]

Failed to allocate memory for the requested size. The memory could not be mapped because there is no memory.

-

-

SYS-3-CERF_RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a cache error

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CERF_ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-PAK_SUBBLOCK_SETSIZE

2-Critical

[dec]

This message indicates an error in startup code to register a pak subblock size. An attempt was made to register a size after the subblock chunk pool had been initialized. This problem is caused by software initialization order.

-

-

SYS-3-RGCREATEFAIL

3-Error

Resource group creation failed\nCause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGADDFAIL

3-Error

Couldn't add process process pid [dec] to resource group [hec]\n Cause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGDELEFAIL

3-Error

Couldn't delete process process pid [dec] from resource group\n \nCause: [chars]

An attempt to remove a process from a resource group failed at the indicated location

-

-

SYS-3-RGDESTFAIL

3-Error

Couldn't destroy resource group [hec]\nCause: [chars]

An attempt to destroy a resource group failed at the indicated location

-

-

SYS-3-RGOPFAIL

3-Error

Requested memory thresholding operation on resource group failed\n Resource Group handle: [hec] Cause: [chars]

The message indicates that an request to Set/Get memory thresholding data or enable/disable thresholding failed in the indicated location

The component that issued the request

-

SYS-3-RGMEMEXCEED

3-Error

\nLimit Exceeded: [chars] Holding: %lu Requested:%lu bytes

A resource group has requested for more memory than the configured limit at the indicated location

The component to which the offending resource group belongs.

-

SYS-2-PAK_SUBBLOCK_BADSIZE

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. The requested size is larger than the maximum registered subblock size.

-

-

SYS-2-PAK_SUBBLOCK_ALREADY

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. A subblock was already associated with the packet.

-

-

SYS-3-IMAGE_TOO_BIG

3-Error

'[chars]' is too large for available memory [dec] bytes.

The allocated memory for the image is too small to hold the image file.

-

"Increase the amount of memory available in the router by booting " "with a smaller image not enabling non-essential sub-systems " "or upgrading the installed memory. Call your technical " "support representative for assistance."

SYS-2-BAD_BM_ARG

2-Critical

Invalid BM index boolean used as argument [dec]

An illegal boolean manager index argument was referenced

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-MAX_IDB_BM_EXCEEDED

2-Critical

BM bit allocation limit exceeded

The BM has exhausted all of the bits available for allocation

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-BAD_BM_NAME

2-Critical

Invalid BM name

An illegal name string was registered with the BM

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-ASSERTION_FAILED

2-Critical

Assertion failed: \[chars]\

An internal state consistency check failed. Correct operation cannot be guaranteed and the system has been halted.

-

LOG_STD_ACTION

SYS-6-STARTUP_CONFIG_IGNORED

6-Information

System startup configuration is ignored based on the configuration register setting.

The configuration register was set to ignore the system startup configuration.

-

"If the system should ignore the startup configuration no action " "is required. If the system should boot with the startup configuration " "saved in the NVRAM change the configuration register value."

SYS-3-URLREADFAIL

3-Error

cannot open file for reading '[chars]'

The URL for the cannot be opened for reading.

-

"Check for proper Uniform Resource Locator syntax and for read " "permission and retry."

SYS-3-TCLSETFAIL

3-Error

cannot set TCL interpreter variable '[chars]' to '[chars]' : '[chars]'

The value could not be passed to the TCL interpreter

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-ESMSHUTDOWN

7-Debug

ESM shutdown

The Embedded Syslog Manager has been shut down

-

LOG_STD_NO_ACTION

SYS-6-LOGGINGHOST_STARTSTOP

6-Information

Logging to host [chars][chars][chars][chars]

Syslog logging to specified server or hostvrf has started or stopped

os-logging

LOG_STD_NO_ACTION

SYS-4-CPURESRISING

4-Warning

[chars][chars] is seeing [chars] cpu util [dec]%% at [chars] level more than the configured [chars] limit [dec] %%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped. CPURESRISING notifications should be matched with the corresponding CPURESFALLING/CPURESUNAPPLY notification.

-

"No action is required"

SYS-6-CPURESFALLING

6-Information

[chars][chars] is no longer seeing [chars] high cpu at [chars] level for the configured [chars] limit [dec]%% current value [dec]%%

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required"

SYS-6-CPURESUNAPPLY

6-Information

[chars][chars] is no longer monitoring [chars] cpu at [chars] level for the configured [chars] limit.

CPU usage is no loger monitored for the configured threshold level mentioned in the error message The corresponding policy is revoked.

-

"No action is required"

SYS-3-BADLIST_DESTROY

3-Error

Removed a non-empty list[hec] name: [chars] having %lu elements

A non-empty list should not be destroyed. If it happens there is a possibility that all elements enqueued into the list will never be deallocated. This message reports that an non-empty list got destroyed.

Determine the component from the stack trace and process name displayed in the error message.

LOG_STD_ACTION

SYS-2-SYSMEMINFO

2-Critical

System Memory: %luK total %luK used %luK free

This is an auxiliary message to several memory-related messages. It\n\ provides system memory information usage.

-

"This message provides additional information only. Copy the error \n\ message exactly as it appears and report it to your technical support \n\ representative as part of a previously printed error message."

SYS-6-LOGGING_BUGINF

6-Information

Logging of buginf debugs was [chars]

All calls to debugging have been disabled in Cisco IOS software as a result the user entering the <CmdBold>no logging buginf<NoCmdBold> command. This command is used to avoid a situation where a large amount of debugging calls might overload the processor CPU hog condition. This

os-logging

"This is an informational message only. No action is required."

SYS-5-FIFOBUS_ERR

5-Notice

Flow-control threshold on module [dec] has exceeded the default value. Threshold will be set to lower value

The FIFO threshold values are monitored for flow-control. When the threshold value exceeds the default the value is set to new lower value

Cat6000-env

LOG_STD_NO_ACTION

SYS-5-PRIV_AUTH_PASS

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_AUTH_FAIL

5-Notice

Authentication to Privilage level [dec] failed by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_I

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-4-GD_DATAUNRELIABLE

4-Warning

Update to memory leak detector on free of 0x[hec] failed CLI output is unreliable\n

managed chunk malloc to store the range that is freed while memory leak detector is in progress failed. Hence memory leak detector will not be updated of this free and this can be reported as leak which is false.

mem

"Ignore the output of \"show memory debug leaks..\" if system is in low " "memory condition else perform a bug toolkit search on the web for " "existing bugs related to this error message if none found contact TAC " "for this problem providing \"show version\" and " "\"show memory statistics\" output."

SYS-3-GD_STACKERR

3-Error

Unknown stack. Process: [chars]\n

An internal error occurred when running the memory leak detector

mem

"Copy the error message exactly as it appears on the console or in the" " system log and look up the message in the Bug Toolkit at:" " http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you are" " unable to resolve the issue using Bug Toolkit please issue a" " \"show tech\" and contact your technical support representative" " with the gathered information."

SYS-4-FREEMEMLOW

4-Warning

Free Memory has dropped below low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-5-FREEMEMRECOVER

5-Notice

Free Memory has recovered above low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the free memory in that pool is now above the configured low-memory limit.

-

"No action is required"

SYS-2-MALLOCFAIL

2-Critical

Memory allocation of [dec] bytes failed from [hex] alignment [dec] \n Pool: [chars] Free: [dec] Cause: [chars] \nAlternate Pool: [chars] Free: [dec] Cause: [chars] \n

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error may have exhausted or fragmented the router's memory.

mem-suspect

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representativeand provide the representative with the gathered information. " "Otherwise you may need to add more memory or reduce the number of " "features you are trying to support."

SYS-2-MUTEXLOCKFAIL

2-Critical

pthread_mutex_lock failed for [chars]

The thread failed in pthread_mutex_lock while trying to acquire a mutex.

mem-suspect

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-NOMEMORY

2-Critical

No memory available for [chars] [dec]

An operation could not be accomplished because of a low-memory condition. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

mem-suspect

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a configuration that has more memory."

SYS-3-CRITMEM

3-Error

[chars]

An attempt to allow or disallow a process from using memory that has been reserved for critical purposes has failed. The location of the failure is specified in the error message. This condition could possibly be caused by a software error.

mem-suspect

"Copy the error message and the traceback messages exactly as they appear " "on the colsole or in the system log contact your technical support " "representative and provide the representative with the gathered " "information."

SYS-2-GETBUFFFAIL

2-Critical

[chars] buffer allocation [dec] bytes failed from [hex]

-

-

-

SYS-6-NOBRIDGE

6-Information

Bridging software not present

Your system is not configured to be a bridge.

none

"Configure the bridging software."

SYS-3-SOCKUNKN

3-Error

Unknown socket protocol [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-HARIKARI

3-Error

Process [chars] top-level routine exited

An internal software error occurred

Determine the component from the process name displayed in the error message.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPID

2-Critical

Bad pid [dec] for tty [t-line]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-MGDTMRRUN

3-Error

TTY[t-line]: Managed Timers [chars] still running

One or more managed timers for a TTY that is deleted are still running.

-

LOG_STD_ACTION

SYS-0-USERLOG_EMERG

0-Emergency

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-1-USERLOG_ALERT

1-Alert

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-2-USERLOG_CRIT

2-Critical

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only. "

SYS-3-USERLOG_ERR

3-Error

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-4-USERLOG_WARNING

4-Warning

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-5-USERLOG_NOTICE

5-Notice

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-6-USERLOG_INFO

6-Information

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-7-USERLOG_DEBUG

7-Debug

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-3-MSGLOST

3-Error

[dec] messages lost because of queue overflow

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-REGEXP

4-Warning

[chars].

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-5-RESTART

5-Notice

System restarted --\n[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SCHEDULED_RELOAD

5-Notice

Reload requested for [chars]

A scheduled reload has been requested for the router.

none

"No action is required."

SYS-5-SCHEDULED_RELOAD_CANCELLED

5-Notice

Scheduled reload cancelled at [chars]

A scheduled reload that was requested for the router has been cancelled.

none

"No action is required."

SYS-5-RELOAD

5-Notice

Reload requested[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SWITCHOVER

5-Notice

Switchover requested[chars]

A switchover was requested.

none

"This is a notification message only. No action is required."

SYS-4-RELOAD_ATTEMPT

4-Warning

Attempt via SNMP failed system shutdown not configured

SNMP cannot be used to reload the router unless this functionality has been previously configured. This message reports that an attempt to reload the router failed because SNMP reloads are not currently configured on the router.

none

"This is a notification message only. No action is required."

SYS-3-CFG_AT_RELOAD

3-Error

System reloading unable to complete startup configuration update

Startup configuration updation is already in progress and reload has been called either from interrupt level or with all interrupts disabled. Reload can not suspend to let startup configuration updation get completed. Startup configuration may get corrupted.

none

"This is a notification message only. No action is required."

SYS-4-DUAL_MESSAGE

4-Warning

SNMP system message request [dec] denied because of pending job

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-5-CONFIG

5-Notice

Configured from [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_I

5-Notice

Configured from [chars] by [chars]

The write of the system running configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_RESOLVE_FAILURE

4-Warning

System config parse from [chars] failed

The configuration file from the URL specified in the error message could not be read.

-

"Enter the <CmdBold>no service config<NoCmdBold> " "command to disable autoloading of configuration files " "OR investigate why the tftp load is failing."

SYS-5-CONFIG_NV

5-Notice

Nonvolatile storage configured from [chars]

The configuration was written successfully.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_NV_I

5-Notice

Nonvolatile storage configured from [chars] by [chars]

The write of the nonvolatile configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-CONFIG_NV_DATA

3-Error

Variable [chars] not set properly in the routine [chars].

The write of the nonvolatile configuration failed because an internal variable was not set properly.

-

"If this messages occurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_NEWER

4-Warning

Configuration from version [dec].[dec] may not be correctly understood

The software detected that the configuration saved in memory was written by a newer version of software. There might be commands saved in memory that are not implemented by the older software version.

none

"Examine all the messages printed while the router was " "booting. For each message about an unknown command determine " "whether that feature is required. If so upgrade to a " "newer version of software that supports that feature."

SYS-4-CONFIG_NOLOCK

4-Warning

The configuration could not be locked

A software error occurred.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SYS-3-CONFIG_NO_PRIVATE

3-Error

No space remaining to save private config

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-CONFIG_NV_OVERRUN

4-Warning

Non config data present at the end of nvram is corrupted

The software detected that the configuration saved into nvram has overlaid a part of the nvram occupied by non config data files.Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_TRUNCATE

4-Warning

Truncated configuration to %ld bytes from %ld bytes

The software detected that the configuration saved into nvram has been truncated. There was not enough space to save the compressed configuration.

-

"Save the configuration to flash if the platform supports " " \"boot config\" command."

SYS-4-CONFIG_NV_NEED_OVERRUN

4-Warning

Non config data present at the end of nvram needs to be overwritten to fit the configuration into nvram

The software detected that the non config data files occupying the end of nvram need to be overwritten to fit the configuration. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_NEED_TRUNCATE

4-Warning

Configuration needs to be truncated to fit into nvram

The software detected that the configuration is to be truncated to fit in the nvram. There was not enough space to save the compressed configuration

-

"Save the configuration to flash if the platform supports " "\"boot config nvbypass\" command."

SYS-4-NV_BLOCK_INITFAIL

4-Warning

Unable to initialize the geometry of nvram

The software detected that it failed to initialize the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload. This may happen when the entire nvram is packed with the configuration and the newer version of software which supports this feature could not find the minimum room in the nvram to initialize block file system.

-

"Reduce the configurations in the nvram atleast by 2K"

SYS-7-NV_BLOCK_INIT

7-Debug

Initialized the geometry of nvram

Initialized the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

""

SYS-4-NV_CHKSUM

4-Warning

An nvram checksum is already in progress

An interrupt service routine attempted to perform a checksum on the nvram contents and found the resource in use.

nvram

-

SYS-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMINIT

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be initialized. reasons are not clear.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent data some corruption.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CONFIG_DOWNFAIL

2-Critical

Generated configuration not backward compatible

The router has been configured to generate nonvolatile memory using the commands of an older software version. The current configuration of the router contains a command that cannot be saved using only the older command set.

none

"Allow the router to save the configuration using the command set of " "the current software version or remove the commands that cannot be " "saved using the older command set."

SYS-5-OUTSETUP

5-Notice

Configuration file [chars] accepted aborting setup

A configuration was accepted over the network so the setup session will be aborted.

none

"This is a notification message only. No action is required."

SYS-3-BADLINKTYPE

3-Error

* Unexpected linktype [dec]

* A software error occurred.

udp

* "Copy the error message exactly as it appears and report it to your " * "technical support representative."

SYS-2-SIGNUM

2-Critical

Process aborted on invalid signal signum = [dec].

An attempt was made to send an invalid signal to another process.

-

"If this message occurs more than once report this message " "to your technical support representative."

SYS-3-CPUHOG

3-Error

Task is running for [dec]msecs more than [dec]msecs [dec]/[dec]

The indicated process ran too long without relinquishing the processor. Each process should run for a small amount of time and then relinquish the CPU so that other processes can run. This problem can be caused by many things like traffic or system load hardware or operational configuration a configuration change initialization of many interfaces cards or ports for example a high momentary error rate a sustained abnormal

If this error occurs in conjunction with a TIMERHOG message \n\ report the two errors together and use the component obtained \n\ for the TIMERHOG message.

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representative and provide the representative with the gathered information."

SYS-2-WATCHDOG

2-Critical

Process aborted on watchdog timeout process = [chars].[chars]

The indicated process ran for too long without relinquishing control. The system killed it as a runaway process.

-

-

SYS-3-TIMERHOG

3-Error

Timer callback ran long PC = [hec].

The indicated callback routine ran for too long without relinquishing the processor.

Determine the component from the callback routine address displayed in\n\ the error message. Use Topic to search for a similar DDTS. If you \n\ find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-6-STACKLOW

6-Information

Stack for [chars] [chars] running low [dec]/[dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-GREEDY_REGEXP

4-Warning

[chars] while processing the input regular expression. Aborting processing use alternate regular expression. Input regular expression: \[chars]\

Regular expression processing limitation: Certain regular expressions require huge stack space for processing or can lead to processing timeouts. We abort processing such regular expressions and print this message to avoid stack overflow/unexpected reload.

os

"The regular expression specified leads to stack overflow/processing " "timeout of the indicated process. Recommended to use a different " "regular expression."

SYS-1-CPURISINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr: [dec]%%/[dec]%%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped.

-

"Enter the <CmdBold>show processes CPU<NoCmdBold>" " command to determine the CPU hogging process" " that is causing this condition and if possible" " disable the activity that is causing the" " CPU hog condition so that CPU" " utilization is reduced."

SYS-1-CPUFALLINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr [dec]%%/[dec]%%.

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required."

SYS-2-INPUTQ

2-Critical

INPUTQ set but no IDB ptr=[hec]

This message is issued when an attempt is made to alter the input queue count for a packet that should not be counted.

-

-

SYS-6-BADSHAREINFO

6-Information

[chars] packet [hec] has a zero reference count freeing pid = [hec] \n\ freeing pc = [hec] [chars].

Provides additional information about original freer of packet.

-

-

SYS-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[hec]

A reference count is used to track the usage of many data structures. A function increments the count when it begins to use a structure and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be negative which means that the data structure will not be freed until the system is reloaded.

-

-

SYS-2-CFORKLEV

2-Critical

Process creation of [chars] failed at level [dec].

An internal software error occurred.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKMEM

2-Critical

Process creation of [chars] failed no memory.

Insufficient memory was available to create a process either while trying to support additional features or due to a memory leak.

mem-suspect

"A memory leak may be the cause if the system has been running for a " "while without changing its configuration. If you suspect a leak then " "copy this message exactly as it appears and report it to your technical " "support representative. Otherwise ensure that more memory is available " "to support the additional features."

SYS-2-CFORKBADFUNCT

2-Critical

Can't create process with start address = [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPROCESS

3-Error

Bad process ID [dec] when [chars] process table

An internal software error occurred.

os-scheduler

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INSCHED

2-Critical

[chars] within scheduler

-

Determine the component from the stack trace displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem.

-

SYS-2-NOTIOSTASK

2-Critical

[chars] from outside IOS task context

An IOS reschedule request was made from code that is not running in the context of an IOS task -- from an interrupt handler the scheduler itself or a service pthread within the IOS process.

Determine the component from the stack trace displayed in the\n\ error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INTSCHED

2-Critical

'[chars]' at level [dec]

The scheduler was entered from an interrupt service routine ISR.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

-

SYS-3-PROCSEMFAIL

3-Error

Process semaphore creation for preemptive processes failed.

Creation of process function semaphore to protect the critical section of process create routine failed. The semaphore creation can fail if there isnt enough chunk memory to create the event structure.

os

-

SYS-2-NOBLOCK

2-Critical

[chars] with blocking disabled.

A process aattempted to relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

-

SYS-2-BLOCKHUNG

2-Critical

Task hung with blocking disabled value = 0x[hec].

The indicated process has exceeded the time limit for which it may relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

"This message may be a result of high loads. If it recurs " "copy the text exactly as it appears and report it along " "with the associated stack trace to your technical support " "representative."

SYS-2-NOTDEAD

2-Critical

Killing process [chars] pid [dec] again

An internal software error occurred.

os-scheduler

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOPROCESS

2-Critical

No such process [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-IMMORTAL

2-Critical

Attempt to shut down management process [dec] [chars].

An attempt was made to shut down the specified management process. Management processes must not be shut down as long as the\n\ router remains up.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the process_kill.

-

SYS-2-SIGPENDING

2-Critical

Multiple Signals are sent to a process [dec]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADSTACK

2-Critical

Process [chars] has trashed stack old size [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-6-MTRACE

6-Information

[chars]: addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC

This is an auxiliary message to several memory-related messages. It provides the address of the memory block and the calling program counter for the last eight blocks allocated and for the last eight blocks freed.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of a previously printed error message."

SYS-6-BLKINFO

6-Information

[chars]blk [hec] words [dec] alloc [hec] [chars] dealloc [hec] rfcnt [hec]

This is an auxiliary message to several memory-related messages. It provides a formatted display of some of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-MEMDUMP

6-Information

[hex]: [hex] [hex] [hex] [hex]

This is an auxiliary message to several memory-related messages. It provides a raw display of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-PROCINFO

6-Information

Process [chars] just finished executing

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

-

"Copy this messages exactly as it appears and report it along with " "the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your " "technical support representative."

SYS-6-TESTINFO

6-Information

Scheduler test [hex] for [chars] just executed

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

Determine the component from the address of the scheduler test routine\n\ displayed in the error message.\n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy this message exactly as it appears and report it along with the " "SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical " "support representative."

SYS-3-BADBLOCK

3-Error

Bad block pointer [hec]

A block of memory at the indicated location is corrupt. An internal check of memory block pointers indicates an inconsistency.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to auotmatically reload then the router will " "need to reloaded manually."

SYS-3-BADMAGIC

3-Error

Corrupt block at [hec] magic %08x

The free memory pool is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADREFCOUNT

3-Error

Bad reference count at [hec] refcount [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-3-OVERRUN

3-Error

Block overrun at [hec] red zone %08x

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-FREEBAD

2-Critical

Attempted to free memory at [hec] not part of buffer pool

An attempt was made to free memory but the request could not be completed due to an invalid memory data structure

-

-

SYS-2-FREEFREE

2-Critical

Attempted to free unassigned memory at %lx alloc %lx dealloc %lx

An attempt was made to free memory at the indicated location. The memory could not be freed because it was not allocated.

-

-

SYS-3-INVMEMINT

3-Error

Invalid memory action [chars] at interrupt level

This message indicates that a memory allocation or deallocation was attempted from an interrupt handler.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-INVMEMPID

3-Error

Invalid pid [dec] in block: [hec]

There has been attempt to allocate memory on behalf of an invalid process.

mem

-

SYS-3-MEMSEMFAIL

3-Error

Mempool semaphore creation failed for [chars]

This message indicates that the semaphore creation for the specified mempool failed.

-

-

SYS-3-INUSEFREE

3-Error

Block [hec] on free list [dec] in use

A memory management function attempted to allocate the indicated block from a list of free blocks. However the block was found to be already in use.

-

-

SYS-3-NZREFCNT

3-Error

Block [hec] on free list [dec] with refcount [dec]

A block of memory in the free pool is actually in use. The message indicates the number of processes using the memory block.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-WRONGFREELIST

3-Error

Block [hec] size [dec] on wrong free list [dec] [dec]

A freed buffer was placed on the wrong list of free buffers.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEMAGIC

3-Error

Corrupt free block at [hec] magic %08x

A block of memory at the indicated location is corrupt. An inconsistency was detected while checking the free memory area.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADPTRVAL

3-Error

Bad pointer value [chars] = [hec] in function [chars]

Corrupted pointer value is encountered.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEPTRS

3-Error

Bad [chars] pointer [hec] at [hec] [chars] = [hec]

A pointer in the block header at the indicated location is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-GETBUF

2-Critical

Bad getbuffer bytes= [dec]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

-

SYS-2-INPUT_GETBUF

2-Critical

Bad getbuffer bytes= [dec] for interface= [chars]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

LOG_STD_ACTION

SYS-2-INLIST

2-Critical

Buffer in list ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-INLIST1

2-Critical

Buffer in list ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED1

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPOOL

2-Critical

Attempt to use buffer with corrupt pool pointer ptr= [hec] pool= [hec]

An memory management function attempted an operation that could not be performed due to invalid memory pool descriptors.

-

-

SYS-2-BADPOOLMAGIC

2-Critical

Attempt to use pool pointer with corrupt header pool= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-WRONGPOOL

2-Critical

Buffer [hec] found in pool [hec] should be in pool [hec]

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-2-BADBUFFER

2-Critical

Attempt to use [chars] buffer as [chars] ptr= [hec] pool= [hec]

A hardware or software error occurred. An inconsistency was encountered while processing a packet buffer.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information."

SYS-2-QCOUNT

2-Critical

Bad [chars] [hec] count [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOTQ

2-Critical

[chars] didn't find [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-LINKED

2-Critical

Bad [chars] of [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SELFLINKED

2-Critical

Buffer [hec] linked to itself in free pool [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-ALREADYFREE

2-Critical

Buffer [hec] already in free pool [chars]

A block of memory at the indicated location is corrupt and/or has been erroneously freed twice.

os

"If this message recurs copy it exactly as it appears and the output " "of 'show buffer address <number>' for the given address as well as " "'show buffer pool <name> dump' for the given pool. Report it to your " "technical support representative."

SYS-2-LOWMEMPROC

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available processor memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak copy the message exactly as it appears and " "report it to your technical support representative. Otherwise you may " "need to add memory or reduce the number of features you are trying to " "support."

SYS-2-LOWMEMIO

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available IO memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak " "copy the message exactly as it appears and " "report it to your technical support representative. " "Otherwise you may need to add memory " "or reduce the number of features you are trying to " "support."

SYS-2-NOMEMFRGPROC

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous processor memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-NOMEMFRGIO

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous IO memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing " "copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-SPEC

2-Critical

Trying to set unknown special character [dec] to [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-ABRUPTTERM

3-Error

Abrupt termination of tty session for [chars] [t-line]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADDISP

3-Error

Bad disposal code [hec] in [chars]

An invalid status code has been passed to a buffer deletion routine. The buffer will be correctly returned to the free pool but will not be correctly counted in the per-protocol statistics.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NULLIDB

3-Error

Null IDB in [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-1-OVERTEMP

1-Alert

System detected OVERTEMPERATURE condition.\n Please resolve cooling problem immediately!\n

The environmental monitor detected a high-temperature condition.

none

"Make sure that the room temperature is not too high and that air flow " "to the card is not blocked. If this condition persists the " "environmental monitor might shut down the system. Call your technical " "support representative for assistance if necessary."

SYS-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADRESID

3-Error

Clock hardware returned bad residual [dec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPRINT

3-Error

Process has no associated tty in [chars].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-INTPRINT

3-Error

Illegal printing attempt from interrupt level.

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-OVFPRINT

3-Error

Overflow in [chars] chars [dec] buffer size [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NOELEMENT

3-Error

[chars]:Ran out of buffer elements for enqueue

The process was unable to enqueue data as it ran out of buffer elements.

-

"Copy the error message exactly as it appears also get the " "output of show buffers and report it to your technical support " "representative."

SYS-6-CLOCKUPDATE

6-Information

System clock has been updated from [chars] to [chars] configured from [chars] by [chars].

This message indicates that the system clock has been modified.

-

"This is informational message."

SYS-5-TABLEERR

5-Notice

[chars] table [chars] damaged: [chars].

An internal table entry became corrupt.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-3-BADTREEPARAM

3-Error

Bad parameter for [chars] passed to tree library function.

This message indicates that a pointer passed to a tree library function is invalid.

-

LOG_STD_SH_TECH_ACTION

SYS-2-BADLIST

2-Critical

Regular expression access check with bad list [dec]

This message indicates that a pointer to an access list is invalid.

-

"The event that caused this message to be issued should not " "have occured. It can mean that one or more data structures " "have been overwritten. If this message recurs and you decide " "to report it to your technical representative you should " "copy the text of the message exactly as it appears and " "include the associated stack trace." "\n\n Since access list corruption may have occurred " "a technical representative should verify that access " "lists are functioning corectly."

SYS-2-SNMP0IDX

2-Critical

Attempt to [chars] snmpidb with if_index of 0

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-SNMP_WRITENET

4-Warning

SNMP WriteNet request. Writing current configuration to [inet]

SNMP is writing the current configuration to a network host.

none

"These are notification messages only. No action is required."

SYS-4-SNMP_HOSTCONFIGSET

4-Warning

SNMP hostConfigSet request. Loading configuration from [inet]

SNMP is reading the host configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-SNMP_NETCONFIGSET

4-Warning

SNMP netConfigSet request. Loading configuration from [inet].

SNMP is reading the network configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-INVALID_IMAGE

4-Warning

Running invalid image for platform!

The software image being run is for a different hardware architecture. This problem can occur on a Cisco 1003 Cisco 1004 or Cisco 1005. The Cisco 1003 and Cisco 1004 use a different image from the Cisco 1005.

none

"Install the correct software image."

SYS-2-CHUNKBOUNDS

2-Critical

Could not find the sibling to allocate memory from. Chunk [chars] total free [dec] inuse [dec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBOUNDSIB

2-Critical

Error noticed in the sibling of the chunk [chars] Chunk index : [dec] Chunk real max : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKFREE

2-Critical

Attempted to free nonchunk memory chunk [hec] data [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKSIBLINGDEST

2-Critical

Attempted to destroy a sibling chunk [hec] [chars].

-

-

-

SYS-2-CHUNKSIBLINGS

2-Critical

Attempted to destroy chunk with siblings chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKPARTIAL

2-Critical

Attempted to destroy partially full chunk chunk 0x[hec] chunk name: \[chars]\.

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKBADMAGIC

2-Critical

Bad magic number in chunk header chunk [hec] data [hec] chunkmagic [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-6-INVALID_BOOTTIME

6-Information

Time since last reboot not available

This is an informational message for the user. The time taken for the router to come up after OIR is not available.

-

"No action required."

SYS-6-BOOTTIME

6-Information

Time taken to reboot after reload = %-4d seconds

This is an informational message for the user. This provides the time taken for the router to come up after reload or crash. The time is actually the difference between the last crash and a successive boot. If autoboot was not set and router is in rommon for a long time then the reload time shown could be large.

-

"No action required."

SYS-2-CHUNKBADREFCOUNT

2-Critical

Bad chunk reference count chunk [hec] data [hec] refcount [hec] alloc pc [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOMEMORY

2-Critical

* Could not allocate chunks for [chars]. No memory

* A software error occurred.

-

* "Copy the error message exactly as it appears and report it to " * "your technical support representative."

SYS-2-CHUNKEXPANDFAIL

2-Critical

Could not expand chunk pool for [chars]. No memory available

There is not enough processor memory left to grow this chunk pool.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADFREEMAGIC

2-Critical

Bad free magic number in chunk header chunk [hec] data [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOROOT

2-Critical

Root chunk need to be specified for [hec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINVALIDHDR

2-Critical

Invalid chunk header type [dec] for chunk [hec] data [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-CRASHINFOINITFAIL

3-Error

Crashinfo subsys initialization did not add registry \n\ crashinfo_get_default_file_name.\n

In order to figure out the device which the crashinfo writes to the crashinfo subsys has to add the registry crashinfo_get_default_file_name.

-

"Use Topic to search for a similar DDTS. If you find none write " "a DDTS for this problem. This SHOULD never happen - it is an " "indication of a bug elsewhere in the code."

SYS-2-CHUNKBADPOOLSIZE

2-Critical

Bad poolsize returned by the system : [dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINCONSIS

2-Critical

Inconsistant counters for chunk : [chars] total free [dec]/[dec] total sibs [dec]/[dec] total alloc [dec]/[dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADELESIZE

2-Critical

Chunk element size is more than 64k for [chars]

Chunk manager cannot function properly with big chunk elements

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-NULLCHUNK

2-Critical

Memory requested from Null Chunk

Chunk manager cannot allocate memory from NULL chunks

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNKSIBLINGSEXCEED

4-Warning

Number of siblings in a chunk has gone above the threshold. Threshold:[dec] Sibling-Count:[dec] Chunk:0x[hec] Name:[chars]

Number of siblings in a chunk with no header has gone above the default/configured threshold configured using <cmdBold>memory chunk siblings threshold<nocmdBold> <cmdArgs>count<nocmdArgs>

-

LOG_STD_SH_TECH_ACTION

SYS-1-CCA_SYS_ERR

1-Alert

CCA Detected System Error code = [dec]

CCA has detected a severe system software error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-2-CCA_INT_ERR

2-Critical

CCA Detected Logic Error code = [dec]

CCA has detected a severe internal logic error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-3-TIMERNEG

3-Error

Cannot start timer [hex] with negative offset [dec].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-MGDTIMER

3-Error

[chars][chars] timer = [hec].

This message indicates an error in a system timer. The problem can be caused either by software or by hardware.

-

-

SYS-3-DMPMEM

3-Error

%08x: %08x %08x %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-BOOT_MESSAGES

6-Information

Messages above this line are from the boot loader.\n

At least one informational or error message was printed by the boot loader.

-

"If the system image was loaded no action is recommended. If the " "system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-2-EXCEPTIONDUMP

2-Critical

System Crashed Writing Core....

The system has crashed because of an exception A core is being generated

-

LOG_STD_ACTION

SYS-3-LOGGER_FLUSHING

3-Error

System pausing to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system is paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_FLUSHED

3-Error

System was paused for %TE to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system was paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_DROPPED

3-Error

System dropped [dec] console debug messages.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

SYS-3-LOGGER_COUNT_STOP_CHUNK

3-Error

System cannot release chunk memory.\n

The system was not able to destroy a previously allocated chunk of memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-CHUNK_NO_EXMEM

3-Error

No handler to [chars] external memory.

An attempt was made to allocate or free a chunk of external memory but no handler for managing external memory was registered.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-READ_BOOTFILE_FAIL

6-Information

[chars] [chars].\n

A configured boot system command failed.

-

"If a system image was eventually loaded no action is recommended. If " "the system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-3-URLWRITEFAIL

3-Error

redirection url write failed '[chars]'

Redirection of output to URL failed.

-

"Check for free space on destination URL and retry."

SYS-6-READ_BOOTFILE_SKIP

6-Information

boot system [chars] command is skipped\n

A configured boot system command is skipped. Either the system experienced a crash while loading this image in the last attempt or the filename is not properly specified. Subsequent boot system commands will be tried

-

"Replace the failed boot system image with a good one. There could be " "various reasons that this specified image failed for example the image " "might be with a bad checksum."

SYS-6-USING_RESERVE_MEMORY

6-Information

Reserve memory is being used

The reserved memory is being used by the console

-

"The system is low in memory. The reserved memory will be " "used only by the console process. Please take a techsupport " "so that the reason for low memory can be found"

SYS-6-RESERVE_MEMORY_CREATED

6-Information

Reserve memory is being created

A portion of memory is reserved exclusively for console

-

"The console access is made available even in low memory " "condition. User can collect the details like tech-support " "for further diagnosis"

SYS-3-BAD_RESET

3-Error

Questionable reset of process [dec] on tty[t-line]\n

A process was reset without giving it a chance to clean itself up.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-DUP_TIMER

3-Error

Same tty[t-line] in linewatch_timers type [dec]

A tty appeared twice in a timer list where it should have only appeared once.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-LINEPROCDEAD

2-Critical

Killing process [chars] associated with line [dec]

A process associated with a tty line was killed by another process. The line may go dead

exec

"If this messages recurs copy it exactly as it appears " "and report it to your technical support representative."

SYS-3-HTIMER_EXPAND

3-Error

timer heap at 0x[hec] needed to expand but hasn't

A timer heap should have expanded but has not

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_INIT

3-Error

heap timer at 0x[hec] has not been initialized

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_STATE

3-Error

heap timer at 0x[hec] in state [dec]

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-MUNMAP

2-Critical

Could not return memory Neutrino via munmap at %lx size [dec] errno [dec]

Failued to unmap memory memory at the indicated location. The memory could not be unmapped because it was allocated via mmap.

-

-

SYS-2-MMAP

2-Critical

mmap failed for size [dec] bytes Caller PC 0x[hec] errno [dec]

Failed to allocate memory for the requested size. The memory could not be mapped because there is no memory.

-

-

SYS-3-CERF_RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a cache error

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CERF_ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-PAK_SUBBLOCK_SETSIZE

2-Critical

[dec]

This message indicates an error in startup code to register a pak subblock size. An attempt was made to register a size after the subblock chunk pool had been initialized. This problem is caused by software initialization order.

-

-

SYS-3-RGCREATEFAIL

3-Error

Resource group creation failed\nCause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGADDFAIL

3-Error

Couldn't add process process pid [dec] to resource group [hec]\n Cause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGDELEFAIL

3-Error

Couldn't delete process process pid [dec] from resource group\n \nCause: [chars]

An attempt to remove a process from a resource group failed at the indicated location

-

-

SYS-3-RGDESTFAIL

3-Error

Couldn't destroy resource group [hec]\nCause: [chars]

An attempt to destroy a resource group failed at the indicated location

-

-

SYS-3-RGOPFAIL

3-Error

Requested memory thresholding operation on resource group failed\n Resource Group handle: [hec] Cause: [chars]

The message indicates that an request to Set/Get memory thresholding data or enable/disable thresholding failed in the indicated location

The component that issued the request

-

SYS-3-RGMEMEXCEED

3-Error

\nLimit Exceeded: [chars] Holding: %lu Requested:%lu bytes

A resource group has requested for more memory than the configured limit at the indicated location

The component to which the offending resource group belongs.

-

SYS-2-PAK_SUBBLOCK_BADSIZE

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. The requested size is larger than the maximum registered subblock size.

-

-

SYS-2-PAK_SUBBLOCK_ALREADY

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. A subblock was already associated with the packet.

-

-

SYS-3-IMAGE_TOO_BIG

3-Error

'[chars]' is too large for available memory [dec] bytes.

The allocated memory for the image is too small to hold the image file.

-

"Increase the amount of memory available in the router by booting " "with a smaller image not enabling non-essential sub-systems " "or upgrading the installed memory. Call your technical " "support representative for assistance."

SYS-2-BAD_BM_ARG

2-Critical

Invalid BM index boolean used as argument [dec]

An illegal boolean manager index argument was referenced

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-MAX_IDB_BM_EXCEEDED

2-Critical

BM bit allocation limit exceeded

The BM has exhausted all of the bits available for allocation

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-BAD_BM_NAME

2-Critical

Invalid BM name

An illegal name string was registered with the BM

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-ASSERTION_FAILED

2-Critical

Assertion failed: \[chars]\

An internal state consistency check failed. Correct operation cannot be guaranteed and the system has been halted.

-

LOG_STD_ACTION

SYS-6-STARTUP_CONFIG_IGNORED

6-Information

System startup configuration is ignored based on the configuration register setting.

The configuration register was set to ignore the system startup configuration.

-

"If the system should ignore the startup configuration no action " "is required. If the system should boot with the startup configuration " "saved in the NVRAM change the configuration register value."

SYS-3-URLREADFAIL

3-Error

cannot open file for reading '[chars]'

The URL for the cannot be opened for reading.

-

"Check for proper Uniform Resource Locator syntax and for read " "permission and retry."

SYS-3-TCLSETFAIL

3-Error

cannot set TCL interpreter variable '[chars]' to '[chars]' : '[chars]'

The value could not be passed to the TCL interpreter

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-ESMSHUTDOWN

7-Debug

ESM shutdown

The Embedded Syslog Manager has been shut down

-

LOG_STD_NO_ACTION

SYS-6-LOGGINGHOST_STARTSTOP

6-Information

Logging to host [chars][chars][chars][chars]

Syslog logging to specified server or hostvrf has started or stopped

os-logging

LOG_STD_NO_ACTION

SYS-4-CPURESRISING

4-Warning

[chars][chars] is seeing [chars] cpu util [dec]%% at [chars] level more than the configured [chars] limit [dec] %%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped. CPURESRISING notifications should be matched with the corresponding CPURESFALLING/CPURESUNAPPLY notification.

-

"No action is required"

SYS-6-CPURESFALLING

6-Information

[chars][chars] is no longer seeing [chars] high cpu at [chars] level for the configured [chars] limit [dec]%% current value [dec]%%

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required"

SYS-6-CPURESUNAPPLY

6-Information

[chars][chars] is no longer monitoring [chars] cpu at [chars] level for the configured [chars] limit.

CPU usage is no loger monitored for the configured threshold level mentioned in the error message The corresponding policy is revoked.

-

"No action is required"

SYS-3-BADLIST_DESTROY

3-Error

Removed a non-empty list[hec] name: [chars] having %lu elements

A non-empty list should not be destroyed. If it happens there is a possibility that all elements enqueued into the list will never be deallocated. This message reports that an non-empty list got destroyed.

Determine the component from the stack trace and process name displayed in the error message.

LOG_STD_ACTION

SYS-2-SYSMEMINFO

2-Critical

System Memory: %luK total %luK used %luK free

This is an auxiliary message to several memory-related messages. It\n\ provides system memory information usage.

-

"This message provides additional information only. Copy the error \n\ message exactly as it appears and report it to your technical support \n\ representative as part of a previously printed error message."

SYS-6-LOGGING_BUGINF

6-Information

Logging of buginf debugs was [chars]

All calls to debugging have been disabled in Cisco IOS software as a result the user entering the <CmdBold>no logging buginf<NoCmdBold> command. This command is used to avoid a situation where a large amount of debugging calls might overload the processor CPU hog condition. This

os-logging

"This is an informational message only. No action is required."

SYS-5-FIFOBUS_ERR

5-Notice

Flow-control threshold on module [dec] has exceeded the default value. Threshold will be set to lower value

The FIFO threshold values are monitored for flow-control. When the threshold value exceeds the default the value is set to new lower value

Cat6000-env

LOG_STD_NO_ACTION

SYS-5-PRIV_AUTH_PASS

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_AUTH_FAIL

5-Notice

Authentication to Privilage level [dec] failed by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_I

5-Notice

Privilege level set to [dec] by[chars][chars]

Switchcards in RFSW has been inserted/removed.

cmts-redundancy

"."

RFSW-3-RELAY_FAIL

3-Error

Relay failed for RFSW.

The relay testing failed.

cmts-redundancy

"Check the connection between CMTS and RFSW."

RFSW-3-HELLO_FAIL

3-Error

Hello message failed between CMTS and RFSW. \nPlease check the connection between CMTS and RFSW.

Hello message between CMTS and RFGW failed.

cmts-redundancy

"Check the connection between CMTS and RFSW."

RFSW-3-LCSO_FAIL

3-Error

Receive a failed LCSO message from RFSW with sequence 0x%04X.

LCSO command failed to execute in RFSW.

cmts-redundancy

"Check the switchcards state in RFSW."

RFSW-6-HELLO_PROTECT

6-Information

The protecting state in RFSW is wrong expect [dec] get [dec].

The protecting state in RFSW is wrong.

cmts-redundancy

"Disable and Enable the configure \"rfswitch auxport enable\"."

RFSW-6-HELLO_ERROR

6-Information

The switchcard in RFSW for slot [dec] group [dec] is in error with the reason [chars].

The switchcards in RFSW is in errro

cmts-redundancy

"Check the switchcard state of RFSW"

HCCP-3-MISS_STATICSYNC_DONE

3-Error

HCCP [chars] member [dec]: Static Sync Done is missed because [chars] Redo static sync through CLI.

HCCP static sync done is missed because of switch over happened or STATICSYNCDONE message missed.

-

"Perform static sync through CLI."

HCCP-6-STATICSYNC_COMPLETED

6-Information

HCCP static sync for [chars] member [dec] is completed in [dec] ms.

HCCP static sync for the groups in list is completed.

-

"."

HCCP-3-MISS_DATAPLANE_READY

3-Error

HCCP [chars] member [dec]: Data Plane Ready is missed because [chars]

HCCP data plane ready is missed because of message missed or data plane error.

-

"Check the status of data plane"

HCCP-3-MISS_CTRLPLANE_READY

3-Error

HCCP [chars] member [dec]: Ctrl Plane Ready is missed because [chars]

HCCP ctrl plane ready is missed because of message missed or ctrl plane error.

-

"Check the status of ctrl plane"

HCCP-3-OUT_OF_ORDER_LC_MSG

3-Error

HCCP slot [dec] member [dec] status [chars]: NULL hp/mp encountered.

HCCP software has detected that messages are Out of Order.

-

LOG_STD_ACTION

HCCP-3-OUT_OF_ORDER_MSG

3-Error

Grp [dec] Mbr [dec] status [chars]: NULL hp encountered.

HCCP software has detected that messages are Out of Order.

-

LOG_STD_ACTION

HCCP-3-OUT_OF_ORDER_LC2RP

3-Error

Grp [dec] Mbr [dec] status [chars]: Received LC to RP sync in standby state. Message rejected.

HCCP software has detected that messages are Out of Order.

-

LOG_STD_ACTION

HCCP-3-BADMSG

3-Error

Grp [dec] Mbr [dec] [chars]: received wrong type of message-[chars].

Certain types of HCCP message are not supposed to be received by Working or Protect.

-

"Check configuration on this interface and the sender's interface"

HCCP-3-UNKNOWN_TLV

3-Error

Grp [dec] Mbr [dec] [chars]: received Unknown TLV type-[dec].

HCCP software has detected Unknown TLV typesthis may not affect the functionality

-

LOG_STD_ACTION

HCCP-5-CHANON

5-Notice

HCCP [chars] Mbr [dec] [chars]: turning on channel.

HCCP LC member notifies that it turns on channel switch.

-

"Make sure peer relinquishes the channel."

HCCP-5-CHANOFF

5-Notice

HCCP [chars] Mbr [dec] [chars]: turning off channel.

HCCP LC member notifies that it turns off channel switch.

-

"Make sure peer controls the channel."

HCCP-5-STANDBY

5-Notice

Grp [dec] Mbr [dec] [chars]: change state from active to standby cause: [chars].

HCCP group member notifies that it changes from active to standby.

-

"Make sure peer controls the channel."

HCCP-5-LC_ACTIVE

5-Notice

HCCP [chars] Mbr [dec] [chars]: change state to active due to: [chars].

HCCP LC member notifies that it changes to active.

-

"Make sure peer relinquishes the channel."

HCCP-5-LC_STANDBY

5-Notice

HCCP [chars] Mbr [dec] [chars]: change state to standby due to: [chars].

HCCP LC member notifies that it changes to standby.

-

"Make sure peer controls the channel."

HCCP-3-BADCHAN

3-Error

HCCP [chars] Mbr [dec] [chars]: channel switch \[chars]\ failed retries exhausted.

HCCP LC member notifies failure in its channel switch.

-

"Make sure channel switch is functioning."

HCCP-5-BULKSYNCINCOMP

5-Notice

Grp [dec] Mbr [dec] [chars]: During PRE bulk syncing ignore LC failover.

Ignore LC failover event when active PRE is syncing data to standby PRE.

cmts-redundancy

-

HCCP-5-SWITCHOVERREADY

5-Notice

HCCP [chars] Mbr [dec] [chars]: ready to switchover.

HCCP LC member suspend timer expires ready to switchover.

-

"."

HCCP-3-BADSTATE

3-Error

HCCP [chars] Grp [dec] inconsistant state !!

HCCP state inconsistancy after control plane switchover

-

"Reset the interface"

HCCP-3-PROTECTING_TOO_MANY

3-Error

Grp [dec] Mbr [dec] status [chars]: Protecting too many Workings.

HCCP detected that protect is asked to protect too many working i/fs.

-

LOG_STD_ACTION

HCCP-4-NOREVERT

4-Warning

HCCP [chars] Mbr [dec]: Revert operation cancelled.

HCCP LC member will not attempt to revert back to the Working interface.

-

"it may have occurred because last time switchover is not finished. " "Make sure the current hccp state is in warm state"

HCCP-4-NOSWOVER

4-Warning

HCCP [chars] Mbr [dec]: switchover is not triggered because [chars].

HCCP LC member will not attempt to revert back to the Working interface.

-

"it may have occurred because last time switchover is not finished. " "Make sure the current hccp state is in warm state"

HCCP-4-PEERBUSY

4-Warning

HCCP [chars] member [dec] Switchover aborted. Protect [chars] is already ACTIVE for member [dec].

HCCP software has detected that the PROTECT linecard is already Active for another Working

-

"Please free up the Protect interface by reverting back to the " "other Working and try this switchover again"

HCCP-6-LC_RPLC_CFGSYNC_CONFIG

6-Information

HCCP [dec] [dec] [chars]: LC [chars] rplc_cfgsync configuration recover is failed PRE will download LC configurations again.

HCCP recover LC rplc_cfgsync configurations is failed because last rplc_cfgsync configuration is not success.

-

"PRE should download LC configurations otherwise it is a critical bug."

HCCP-6-LC_RPLC_CFGSYNC_CONFIG_RECOVER

6-Information

HCCP [dec] [dec] [chars]: LC [chars] rplc_cfgsync configuration recover is succeed.

HCCP recover LC rplc_cfgsync configurations is succeed.

-

"."

HCCP-6-LC_RPLC_CFGSYNC_CONFIG_PARSER

6-Information

Parser Error: [dec]

HCCP recover LC rplc_cfgsync configurations parser error.

-

"."

HCCP-6-HCCP_CHAN_RFSW_SNMP_ERROR

6-Information

[chars] error: [chars].

HCCP channel process errors related SNMP.

-

"."

HCCP-6-HCCP_CHAN_RFSW_SNMP_INFO

6-Information

[chars]: [chars].

SNMP response.

-

"."

HCCP-3-CFG_FAIL

3-Error

Configuration failed. [chars]

An error occurred during configuration.

-

LOG_STD_SH_TECH_ACTION

HCCP_LC_ISSU_SHIM-3-REVERTIVE_CFG

3-Error

HCCP revertive configuration exists for interfaces on slot [dec]/[dec].

HCCP revertive is enabled for the protect interfaces on the given line card. For ISSU to function without being disrupted by automatic revert backs please configure interfaces to be non-revertive.

cmts-platform

"Configure interfaces to be non-revertive."

HCCP_LC_ISSU_SHIM-3-RP_HIGH_CPU_UTILIZATION

3-Error

High CPU utilization on PRE line card ISSU may fail.

Line card ISSU may fail due to high CPU utilization on the PRE.

cmts-platform

"Attempt line card ISSU when PRE has lower CPU load"

HCCP_LC_ISSU_SHIM-3-CLC_HIGH_CPU_UTILIZATION

3-Error

High CPU utilization on line card [dec]/[dec] line card ISSU may fail.

Line card ISSU may fail due to high CPU utilization on the line card.

cmts-platform

"Attempt line card ISSU when line card has lower CPU load"

HCCP_LC_ISSU_SHIM-3-SWITCHOVER_FAILURE_EXTERNAL_RF_SWITCH

3-Error

Switchover from line card [dec]/[dec] aborted.

HCCP switchover from the give slot is aborted due to external RF switch error in the HCCP LC ISSU shim layer.

cmts-platform

"Check the network connection between the router and " "the external RF switch."

HCCP-3-DATA_PLANE_READY

3-Error

HCCP data plane for [chars] member [dec] is ready.

HCCP lc2rp sync for the groups in list is completed.

-

"."

HCCP-3-CTRL_PLANE_READY

3-Error

HCCP ctrl plane for [chars] member [dec] is ready.

HCCP ctrl plane is ready to receive lc2rp sync for the groups in list.

-

"."

HCCP-6-IGNORE_MD_UP

6-Information

The member [chars] [dec][[dec]] is already up ignore repeated event.

The mac domain is already active ignore the repeated up events.

-

"."

HCCP-3-INVALID_PROTECT

3-Error

ERROR!LC-RED: License of protect card [dec]/[dec] is incompatible with working card [dec]/[dec].

The protect linecard has lower license.

-

"Please upgrade the license on the protect"

HCCP-3-CONFIGSYNC_ERROR

3-Error

Enable config-sync when it is not disabled

HCCP internal flag configsync the software is trying to enable this flag set to 0 while it is already enabled 0.

ubr10000

"Reset the system"

HCCP-3-CFR_LIST

3-Error

Remove an element before destroy [chars]: cfrid=[dec] direction=[dec] state=[dec] ip_sadd=[inet] ip_daddr=[inet] dest_macaddr=[enet] src_macaddr=[enet] ip_prot=[dec] eport=[dec]

Remove an element from interdb cfr_list before destroy the list.

ubr10000

"Reset the system"

OIR-6-REMCARD

6-Information

Card removed from slot [dec] interfaces disabled

The OIR facility detected the removal of a processor from the slot number specified in the error message. The interfaces on that processor will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces.

-

LOG_STD_NO_ACTION

OIR-6-INSCARD

6-Information

Card inserted in slot [dec] interfaces administratively shut down

The OIR facility detected a newly inserted processor. The interfaces associated with that processor are operational but will be shut down until they are configured by the user. If any interfaces of that type were previously configured they will be restored to their previous state.

-

LOG_STD_NO_ACTION

OIR-3-LONGSTALL

3-Error

Long bus stall [dec] ms check for improperly seated cards

An online insertion or removal of an interface processor card has stalled the backplane bus for longer duration than expected.

-

"Make sure all interface processor cards are inserted or removed. " LOG_STD_ACTION_ERR

OIR-4-NOEOIR

4-Warning

[chars] [chars] version [dec].[dec] not capable of EOIR

-

-

"Try to restrict insertion or removal of this card to times when a\n\ CBUS complex restart will be least disruptive.\n\ Or upgrade the card to the latest revision which supports EOIR."

OIR-3-SEATED

3-Error

Insert/removal failed for slot [dec] check card seating

The OIR facility detected an incorrectly seated card\n\ causing the insertion or removal of this card to fail.

-

"Reseat the card in the indicated slot."

OIR-3-CRASH

3-Error

The module in slot [dec] has crashed

The module in the slot indicated has crashed and will be rebooted by\n\ the supervisor.

-

"Collect the crashinfo file from the crashed module and contact\n\ support."

CBUS-4-RSETFAIL

4-Warning

Interface [chars] failed to reset properly in [chars] code [hex]

An interface reset command failed. This may be a software or hardware\n\ problem.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-OUTHUNG

3-Error

[chars]: tx[chars] output hung %-04x - [chars] [chars]

A transmission attempt on an interface failed. The interface might not\n\ be attached to a cable or there might be a software problem.

-

"Check that the interfaces are all connected to the proper cables. If\n\ that is not the problem call your technical support representative."

CBUS-4-NOCOOKIE

4-Warning

[chars]-[dec] controller missing configuration data - disabled

The controller type was derived from a hardware probe. The controller\n\ number indicates the ciscoBus relative slot number. This is a hardware\n\ error

-

LOG_STD_SH_TECH_ACTION

CBUS-3-TESTFAIL

3-Error

Unit [dec] failed [chars] test - interface disabled

A hardware component failed an internal diagnostic test.

-

"Check switch settings on the interface cards. Check for proper unit\n\ numbers. Reset the cards. Replace the malfunctioning device."

CBUS-3-DAUGHTER

3-Error

Unit [dec] daughter controller [dec] failed [chars] test - interface disabled

-

-

"First check that the daughter controller card is properly seated in\n\ its Multibus and ciscoBus connectors. Next swap daughter cards and\n\ check whether the error follows the daughter card or the slot. If the\n\ message recurs call your technical support representative for\n\ assistance."

CBUS-3-DAUGHTER_NO_RSP

3-Error

Unit [dec] daughter [dec] not responding 0x%04x - disabled

-

-

"First make sure that the daughter card is properly seated in its\n\ Multibus and ciscoBus connectors. If this message recurs copy the \n\ error message exactly as it appears on the console or in the system\n\ log contact your Cisco technical support representative and provide\n\ the representative with the gathered information"

CBUS-3-CORRUPT

3-Error

Controller [dec] wrote 0x%-04x read 0x%-04x loc 0x%-04x - dci_memtest

A hardware component failed an internal diagnostic test.

-

"Replace the malfunctioning device."

CBUS-3-TXALLOC

3-Error

Error %-04x tx_allocate - cbus_init

A hardware device did not respond appropriately to a request.

-

"Make sure the device is functioning and is configured correctly."

CBUS-3-BUFFER

3-Error

Controller [dec] Error %-04x Buffersize = [dec] Bufferpool = [dec] number [dec]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-INITERR

3-Error

Interface [dec] Error %-04x idb %08x [dec] [chars] - cbus_init

The switch processor or ciscoBus controller signaled an error while\n\ processing a packet or selecting an interface. This indicates a\n\ software problem.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-INTR

3-Error

Interface [dec] idb %08x [dec] [chars] - cbus_interrupt

The switch processor or ciscoBus controller returned a nonsensical\n\ value.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CBUSBCE

3-Error

Failed to select a BCE response 0x%04x - cbus_bce_update_ifa

A hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CBUSBCEPERM

3-Error

Failed to select a BCE response 0x%04x - cbus_bce_permissions_update

A hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-FDDIRSET

3-Error

Interface [chars] Error %-04x [chars] - fddi_reset

A hardware device did not respond appropriately to a request.

-

"Make sure the device is functioning and is configured correctly."

CBUS-3-FDDIRSETU

3-Error

Unit [dec] Error %-04x [chars] - fddi_reset

A hardware device did not respond appropriately to a request.

-

"Make sure the device is functioning and is configured correctly."

CBUS-5-FDDICMD

5-Notice

'[chars]' is not supported on [chars]

This command is not supported on this FDDI interface.

-

LOG_STD_NO_ACTION

CBUS-3-HSSIRSET

3-Error

Interface [chars] Error %-04x [chars] - hssi_reset

A command to reset an HSSI interface was issued by the RSP\n\ but the interface did not respond to the command within the\n\ expected time delay. The delay is given for the processor to\n\ return the buffers that it has allocated and to perform any\n\ necessary cleanup. This condition may be caused by a large number\n\ of buffers that have been allocated by the interface due to either\n\ heavy traffic or a hardware problem with the interface.

-

"Verify that the card is properly seated. If this error recurs \n\ then issue the <CmdBold>show tech-support<NoCmdBold> and\n\ <CmdBold>show logging<NoCmdBold> commands contact your Cisco \n\ technical support representative and provide the representative\n\ with the gathered information."

CBUS-3-SRPRSET

3-Error

Interface [chars] Error %-04x [chars] - srp_reset

A command to reset an SRP interface was issued by the RSP\n\ but the interface did not respond to the command within the\n\ expected time delay. The delay is given for the processor to\n\ return the buffers that it has allocated and to perform any\n\ necessary cleanup. This condition may be caused by a large number\n\ of buffers that have been allocated by the interface due to either\n\ heavy traffic or a hardware problem with the interface.

-

"Verify that the card is properly seated. If this error recurs \n\ then issue the <CmdBold>show tech-support<NoCmdBold> and\n\ <CmdBold>show logging<NoCmdBold> commands contact your Cisco \n\ technical support representative and provide the representative\n\ with the gathered information."

CBUS-3-CTRRAMTEST

3-Error

Interface [chars] RAM Addressing Test Failed - [chars]

The Token Ring interface failed its memory diagnostic tests.

-

"Issue a <Bold>clear interface<NoBold> command. " LOG_STD_RECUR_ACTION

CBUS-3-CTRINIT

3-Error

Interface [chars] CTR Initialization Failed - [chars]

The Token Ring interface failed one of its internal self-tests.

-

"Issue a <Bold>clear interface<NoBold> command. " LOG_STD_RECUR_ACTION

CBUS-3-CTRCMDFAILED

3-Error

Interface [chars] CTR Command [chars] Failed [chars] %#04x

A command sent from the system to the Token Ring interface failed to\n\ complete successfully.

high-token

LOG_STD_SH_TECH_ACTION

CBUS-3-CTRCMDFAILED2

3-Error

Interface [chars] CTR Command [chars] Failed Code %#04x

A command sent from the system to the Token Ring interface failed to\n\ complete successfully.

high-token

LOG_STD_SH_TECH_ACTION

CBUS-3-CTRRSET

3-Error

Interface [chars] failed to initialize

The Token Ring interface failed to insert into the Token Ring.\n\ The interface is placed into reset state and will not \n\ automatically try to re-insert itself.

high-token

"Issue a <Bold>clear interface<NoBold> command. " LOG_STD_RECUR_ACTION

CBUS-3-CTRACHECK

3-Error

Interface [chars] Adapter Check Error %04x %04x %04x %04x

The Token Ring monitor firmware detected a fatal error on the\n\ interface card.

high-token

"Issue a <Bold>clear interface<NoBold> command. " LOG_STD_RECUR_ACTION

CBUS-3-CTRUCHECK

3-Error

Interface [chars] Microcode Check Error

The Token Ring interface microcode detected an unrecoverable error.

high-token

"Issue a <Bold>clear interface<NoBold> command. " LOG_STD_RECUR_ACTION

CBUS-3-CTRBADLOVE1

3-Error

Interface [chars] SRB_COMPLETE lovenote received with unknown command 0x%04x

The system received a message from the Token Ring interface\n\ but does not recognize the message.

high-token

LOG_STD_SH_TECH_ACTION

CBUS-3-CTRBADLOVE1_DUMP

3-Error

Dump of MEMB follows\n-SRB_ADDR: %04x %04x %04x %04x %04x %04x %04x %04x

The system is printing codes related to a previous lovenote error\n\ message.

high-token

LOG_STD_SH_TECH_ACTION

CBUS-4-CTRBADLOVE2

4-Warning

Interface [chars] Unexpected SRB_COMPLETE lovenote command=0x%04x result=0x%04x

The system received an unsolicited message from the Token Ring interface.\n\ The system ignored the message and continued normal processing.

high-token

LOG_STD_RECUR_ACTION

CBUS-3-RESETNXI

3-Error

Reset of removed interface [hec] [chars]

An interface reset was attempted on an interface that was removed from\n\ the router. This message appears if you use the shutdown command to\n\ bring down a removed interface.

-

LOG_STD_NO_ACTION

CBUS-3-FSIPRSET

3-Error

Interface [chars] Error %-04x [chars] - fsip_reset

-

-

"Check FSIP electrical connections cable and ciscoBus connections. An\n\ FSIP microcode reload will be required. If the check of electrical\n\ connections reveals no problems and the message recurs call your\n\ technical support representative for assistance."

CBUS-3-SERRSET

3-Error

Interface [chars] Error %-04x [chars] - serial_reset

A software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CATMRSET

3-Error

Interface [chars] Error %-04x [chars] - aip_reset

A software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CATMRSETU

3-Error

Unit [dec] Error %-04x [chars] - cbus_atm_reset

A software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CATMCFG

3-Error

Interface [chars] Cannot config interface CBus ATM MEM 0x[hec] status [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-AIPINVPLIM

3-Error

Interface [chars] Invalid PLIM detected. Interface downed

A software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-BADVC

3-Error

[chars] [dec]/[dec] got bad VC packet \n%08x %08x %08x %08x %08x %08x %08x %08x

An interface received a packet with bad VC encapsulation. \n\ This indicates either a software or hardware problem.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-POLLFAIL

3-Error

Interface [chars] failed to respond debug info follows

A Token Ring interface card failed to respond to periodic polling.\n\ This can indicate a software or hardware problem.\n\ See CBUS-3-POLLFAILDAT for the syntax of this message.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-POLLFAILDAT

3-Error

Int [dec]: %04X %04X %04X %04X %04X %04X

This is the debugging information for the CBUS-3-POLLFAIL error.

-

LOG_STD_DBG_ACTION

CBUS-3-FCICMDFAIL0

3-Error

Controller [dec] cmd [dec] failed 0x%-04x count [dec]

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-FCICMDFAIL1

3-Error

Controller [dec] cmd [dec] 0x%-08x failed 0x%-04x count [dec]

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-CTRLRCMDFAIL0

3-Error

Controller [dec] cmd [dec] failed 0x%-04x count [dec]

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-CTRLRCMDFAIL1

3-Error

Controller [dec] cmd [dec] 0x%-08x failed 0x%-04x count [dec]

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-CCBCMDFAIL0

3-Error

Controller [dec] cmd [dec] failed 0x%-04x

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-CCBCMDFAIL1

3-Error

Controller [dec] cmd [dec] 0x%-08x failed 0x%-04x

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-CCBCMDFAIL3

3-Error

Controller [dec] cmd [dec] 0x%-04x 0x%-04x 0x%-04x failed 0x%-04x

A command sent from the system to an interface processor failed to\n\ complete successfully.

-

"The system recovered by generating an error code to the requester."

CBUS-3-UNKENC

3-Error

Interface [chars] unknown encaps type [hec]

A packet was received from the CIP with an unknown encapsulation type.\n\ The packet will be dropped.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CT3STAT

3-Error

Out of buffers--losing status information for CT3 on VIP card

A status information message from the VIP was received.\n\ A memory buffer is required to process the status information \n\ message but the memory allocation routine due to insufficient\n\ system buffer memory. Therefore the status information message\n\ was not processed. This condition may be caused either by a heavy \n\ memory utilization at the time of the memory buffer request or by\n\ insufficient memory in the system.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this \n\ message recurs or appears regularly contact your Cisco technical \n\ representative to upgrade the memory of the system."

CBUS-3-HALSTAT

3-Error

Out of buffers--losing status information for ChSTM-1 on VIP card

An internal software resource has been exhausted.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-POTSTAT

3-Error

Out of buffers--losing status information for POTENT on VIP card

An internal software resource has been exhausted.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CT3DSX3ERR

3-Error

[chars]Illegal dsx3 value - unit is [dec]

-

-

-

CBUS-3-CE3DSX3ERR

3-Error

[chars]Illegal E3 value - unit is [dec]

-

-

-

CBUS-3-HALSDHERR

3-Error

[chars]Illegal sdh value - unit is [dec]

-

-

-

CBUS-5-CBADVCSETUP

5-Notice

Interface [chars] setup vc failed with vci exceeding vc-per-vp - 3

The TI1570 chip reserves 3 RX DMA channels for OAM cells. As a result the last 3 VCIs of the last VPI block cannot be used for regular traffic.

-

"Avoid try different vci/vpi combinations."

CBUS-3-CFGCMDDROPPED

3-Error

Config queue is full command was dropped slot [dec]

Sending a config command was retried. The receiving\n\ queues were still full after retries therefore the command was dropped.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-ADDRFILTR

3-Error

Interface [chars] address filter [chars] command failed code %#04x

The specified address filter command sent to the specified\n\ interface failed with the displayed error code.

cbus

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-BADRXEOFVEC

3-Error

[chars] ustatus: [chars] %04x %04x %04x %04x %04x

Debugging information when an IP panics.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-BADTXSTATE

3-Error

[chars] ustatus: [chars] %04x %04x %04x %04x %04x

Debugging information when an IP panics.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-BADTXEOFVEC

3-Error

[chars] ustatus: [chars] %04x %04x %04x %04x %04x

Debugging information when an IP panics.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-TXSTARTPENDACTIVE

3-Error

[chars] ustatus: [chars] %04x %04x %04x %04x %04x

Debugging information when an IP panics.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-UNKNOWN

3-Error

[chars] ustatus: [chars] %04x %04x %04x %04x %04x

Debugging information when an IP panics.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-CMDTIMEOUT

3-Error

Cmd timed out CCB 0x[hec] slot [dec] cmd code [dec]

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CMDDROPPED

3-Error

Cmd dropped CCB 0x[hec] slot [dec] cmd code [dec]

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CCBSEMINFO

3-Error

CCB semaphore acquired traceback:[chars]\n CCB semaphore released traceback:[chars]

More information on the CCB semaphore. The tracebacks indicate the program counters and stack that point to the code that was the last to acquire this semaphore and the last to release this semaphore respectively

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CCBPTIMEOUT

3-Error

CCB handover timed out CCB 0x[hec] slot [dec]

A hardware or software error occurred.

cwpa

"Please gather the logs and tracebacks " "and contact the TAC"

CBUS-3-PORTTYPE

3-Error

Unexpected interface type for [chars][dec] port [dec] type [dec]

A hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-CMD

3-Error

Cmd failed: [chars] response %#04x [chars]

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-3-MODULE

3-Error

Missing [chars] for [chars]

A hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-3-NOBUF

3-Error

Buffer allocation failure: [chars]

A hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

CBUS-5-INPUTERR

5-Notice

Interface [chars] excessive input error rate

Interface disabled because too many input errors occurred.

-

"Inspect condition of attached network hardware"

CBUS-4-FIXBADTXVC

4-Warning

Detected and fixed bad tx vc encap on [chars] bad vc [dec] fixed vc [dec]

A transmit packet on a channelized serial interface does not\n\ have the vc number encapsulation

-

LOG_STD_SH_TECH_ACTION

CBUS-3-TXVCENCAPFAIL

3-Error

Detected bad tx vc encap on [chars] vc [dec]. Board encap failed [hex] [hex] [hex]

Board encap failed on a transmit packet on a channelized serial \n\ interface which does not have the vc number encapsulation

-

LOG_STD_SH_TECH_ACTION

CBUS-3-SELECTBADVC

3-Error

Select invalid vc number [dec].

An invalid channel number is selected

-

LOG_STD_SH_TECH_ACTION

CBUS-3-SENDIPCMDFAIL

3-Error

Send Ip Cmd Failed. Command dropped after [dec] retries CCB 0x[hec] slot [dec] cmd code [dec]\n

Sending an ip command was retried. The receiving queues were still\n\ full after retries therefore the command was dropped.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CBUS-5-SENDIPCMDRECOV

5-Notice

Send Ip Cmd Succeeded after [dec] retries CCB 0x[hec] slot [dec] cmd code [dec]\n

Sending an ip command was retried due to receiving queues being full.\n\ But after some retries command was send successfuly.

-

LOG_STD_NO_ACTION

DBUS-3-ORFS_NOTINITIALIZED

3-Error

ORFS is not initialized

When oir-remove-failing-slot is invoked the software attempts to initialize parameters. This initialization failed and the service will not be available.

rsp

"If this message is seen please try entering the service " "oir-remove-failing-slot command again. This message should " "not cause any functional failures. If the message does cause " "an IOS performance issue please check Bug Toolkit on the web " "for existing bugs and if none are found " LOG_STD_SH_TECH_ACTION

DBUS-3-CXBUSERR

3-Error

Slot [dec] CBus Error

-

-

"Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION

DBUS-3-DBUSINTERR

3-Error

Slot [dec] Internal Error

A processor reported an internal error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested.

-

"Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION

DBUS-3-DBUSINTERRSWSET

3-Error

Slot [dec] Internal Error due to VIP crash

A processor reported an error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested.

-

"Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION

DBUS-3-DBUSDISABLED

3-Error

Slot [dec] disabled will be restarted.

A processor was disabled due to an error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested.

-

"Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION

DBUS-3-WCSCTRLRERR

3-Error

Slot [dec] WCS Controller Instruction Error

-

-

LOG_STD_SH_TECH_ACTION

DBUS-3-WCSPARERR

3-Error

Slot [dec] WCS Controller Parity Error

A processor reported a WCS parity error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested.

-

"Replace the processor or download microcode. If this message recurs\n\ call your Cisco technical support representative for assistance."

DBUS-3-DAUGHTER_STATS

3-Error

Slot [dec] control 0x[hec] status 0x[hec]

A processor reported an error. This message is sent out in conjunction\n\ with other error messages to provide additional information.

-

LOG_STD_SH_TECH_ACTION

DBUS-3-SLOTCOMP

3-Error

Slot [dec] dbus error slot 0x[hec] and complement 0x[hec] do not match

A processor reported a mismatch between the contents of the slot\n\ register and its complement. This condition indicates a hardware\n\ failure in the diagnostic bus controller on that processor or on the\n\ diagnostic bus. The processor will be reset and not used until the next\n\ OIR event or microcode download when it will be retested.

-

LOG_STD_SH_TECH_ACTION

DBUS-3-WCSERR

3-Error

Slot [dec] WCS controller in error state 0x[hec] resetting

-

-

"Reset the processor and load new microcode. " LOG_STD_RECUR_ACTION

DBUS-3-WCSLDERR

3-Error

Slot [dec] error loading WCS status 0x[hec] cmd/data 0x[hec] pos [dec]

A processor indicated an error condition while downloading microcode.\n\ The status cmd/data and pos numbers shown in the message reflect the\n\ error condition the last byte of microcode loaded and the position in\n\ the file respectively. If this error appears the microcode download\n\ is aborted and the ROM microcode is loaded.

-

LOG_STD_RECUR_ACTION

DBUS-3-WCSFLOW

3-Error

Slot [dec] flow cntrl error loading WCS last data 0x[hec] pos [dec]

A processor indicated an error condition while downloading microcode.\n\ The status cmd/data and pos numbers shown in the message reflect the\n\ error condition the last byte of microcode loaded and the position in\n\ the file respectively. If this error appears the microcode download\n\ is aborted and the ROM microcode is loaded.

-

LOG_STD_RECUR_ACTION

DBUS-2-UNKNOWN

2-Critical

Slot [dec] unknown controller type 0x[hec] ignoring

A processor reported a controller type that is unknown to the system.\n\ The processor will not be used and needs to be repaired.

-

LOG_STD_SH_TECH_ACTION

DBUS-3-XILINX

3-Error

ready wait timeout slot [dec]

The field-programmable gate arrays on an interface processor failed to\n\ load after being reset. This indicates a probable software or hardware\n\ problem.

-

LOG_STD_ACTION

DBUS-3-NOMAGIC

3-Error

No magic number found in RP1 EEPROM

The structure containing the system MAC address needed by the OIR\n\ facility cannot be found in the RP EEPROM. The RP must be returned for\n\ reprogramming.

-

"Return the RP for reprogramming and call your Cisco technical\n\ support representative for assistance."

DBUS-3-BADEEPROM

3-Error

Invalid EEPROM data found for card in slot [dec] card disabled

The ID EEPROM on the indicated card is not programmed correctly.

-

"Call your Cisco technical support representative for a replacement."

DBUS-3-SW_NOTRDY

3-Error

DBUS software not ready for slot [dec] after [chars] elapsed [dec] status 0x[hec]

An interface processor failed to come online after being reset. A software or hardware error occurred.

rsp c5rsm

"Please refer to Bug Toolkit on the Cisco web-site to check for " "existing bugs. If you do not find one obtain the output of show " "tech and show log and open a TAC case."

DBUS-3-BADCTRLRTYPE

3-Error

Invalid controller type [dec] in slot [dec]

An interface processor responded with an unknown or illegal controller\n\ type when queried. This should not happen unless the running software\n\ does not support the interface processor in question or the interface\n\ processor fails.

-

LOG_STD_ACTION

DBUS-3-NORESP

3-Error

bad or no response slot [dec]

A board in the slot identified in the error message failed to\n\ respond.

-

LOG_STD_SH_TECH_ACTION

DBUS-3-BADHSACONF

3-Error

Down rev RSP EPROM found HSA system upgrade EPROM or remove one RSP

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

DBUS-3-NOSUPPORT

3-Error

No driver support in this image for [chars] in slot [dec] card type [dec] - disabled

The Cisco IOS image does not have driver support code\n\ for the specified interface processor.

-

"Remove the unsupported interface processor card or\n\ reload the router with a Cisco IOS image that has driver\n\ support code for that interface processor card."

DBUS-3-MSGOVERFLOW

3-Error

Slot [dec] too many DBUS messages

A board in the slot identified in the error message tried to send\n\ too many logger messages.

-

LOG_STD_SH_TECH_ACTION

DBUS-3-MSGPAUNSUP

3-Error

Slot [dec] has an unsupported PA in bay [dec]

The PA in the slot is not supported either because the VIP is\n\ incompatible with it or because the IOS has no pertinent drivers.

-

"Please refer to the documentation of the PA to get a list of compatible\n\ VIP's. If the VIP that contains the PA is listed as supported please refer to\n\ the CCO page for IOS versions that support the PA. Otherwise seat the PA in one\n\ of the supported VIP's and verify that the IOS version supports the PA."

DBUS-3-MSGPABADCONFIG

3-Error

Slot [dec] has an unsucessfully configured PA in bay [dec]

The PA in the slot is not sucessfully configured either because the VIP is\n\ incompatible with it or because the IOS has no pertinent drivers.

-

"Please refer to the documentation of the PA to get a list of compatible\n\ VIP's. If the VIP that contains the PA is listed as supported please refer to\n\ the CCO page for IOS versions that support the PA. Otherwise seat the PA in one\n\ of the supported VIP's and verify that the IOS version supports the PA."

TDM_CLOCK_SYNCHRONIZATION-4-TDMCLK_CHANGE

4-Warning

\nTDM frame clock source transitioned from\n\ Priority [dec] [chars] [chars] to Priority [dec] [chars] [chars]\n

This warning message indicates a change in the clock source.

-

"No action required."

TDM_CLOCK_SYNCHRONIZATION-4-TDMCLK_LOST_LOCK

4-Warning

\nTDM frame clock [chars] lost lock - clock source failed.\n

The clock source has failed.

-

"If alternate source is available it will be used."

TDM_CLOCK_SYNCHRONIZATION-4-TDMCLK_STATE_CHG

4-Warning

\nTDM frame clock state change state: [chars] \n

This debug message indicates a clock state change

-

"No action required."

TDM_CLOCK_SYNCHRONIZATION-4-TDMCLK_STATE_ERR

4-Warning

\nTDM frame clock state error state: [chars] event: [chars]\n

This warning message indicates a invalid clock event

-

"No action required."

ECC-2-MALLOC

2-Critical

Attempt to malloc [dec] bytes for the ECC error log failed.\n ECC errors will only be reported and not recorded.\n

Malloc for the ECC error log failed. A memory upgrade would be advisable or is recommended.

-

LOG_STD_ACTION

ECC-3-SBE_HARD

3-Error

Single bit *hard* error detected at 0x%08x

A single-bit uncorrectable error [hard error] was detected on a CPU\n\ read from DRAM. 'show ecc' will dump the Single-bit errors logged thus\n\ far and will also indicate detected hard error address locations.

-

"Monitor system through 'show ecc' and replace DRAM if too many\n\ such errors."

ECC-3-SBE_LIMIT

3-Error

Single bit error detected and corrected\nat 0x%08x

A single-bit correctable error was detected on a CPU read from DRAM.

-

LOG_STD_ACTION

ECC-3-SBE_RMW_LIMIT

3-Error

Single bit error detected and corrected at 0x%08x on a read-modify-write cycle

A single-bit correctable error was detected on during a read-modify-\n\ write cycle on a CPU read from DRAM for a non 8-byte access.\n\ 'show ecc' can be used to dump Single-bit errors logged thus far.

-

LOG_STD_ACTION

ECC-3-SYNDROME_SBE_LIMIT

3-Error

8-bit Syndrome for the detected Single-bit error: 0x[hec]

The 8-bit syndrome for detected single-bit error. This value does not\n\ indicate the exact positions of the bits in error but can be used to\n\ approximate their positions.

-

LOG_STD_ACTION

SONETIFMIB-3-OUTOFBOUND

3-Error

Out of bound values path=[dec]/tug2=[dec]/e1=[dec]

Invalid values used while determining the ifAlias

-

"LOG_STD_NO_ACTION"

SONETIFMIB-3-NULLPTR

3-Error

NULL pointer at step = [dec]

Attempted to initialize ifAlias for VT using a NULL pointer.

-

"LOG_STD_NO_ACTION"

COPTMONMIB-3-ENTRYPRESENT

3-Error

An entry is already present for the registering interface with ifIndex [dec]

An entry in the OPTICAL MONITORING MIB is already existing for the registering interface

gsr-netmgmt

""

COPTMONMIB-3-ENTRYADDFAILED

3-Error

Registering of the interface with ifIndex [dec] to local data structure failed

An attemt to make an entry for the registering interface failed

gsr-netmgmt

""

AIP-3-AIPFAILSETUPVC

3-Error

[chars] Failed to setup vc [dec] Cause: [chars]

-

-

-

AIP-3-AIPFAILSETUPVCAVG

3-Error

Interface [chars] Failed to setup vc [dec] Cause: [chars] Expected range [[dec] .. [dec]]Kbps for AIP Average Rate Metering. Average Rate=Peak Rate= [dec] Kbps turns Average Rate Metering OFF

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

UCODE-3-BADCHKSUM

3-Error

Bad checksum in [chars] found 0x[hec] expected 0x[hec]

-

-

"Reload the microcode. If the message recurs call your technical\n\ support representative for assistance."

UCODE-3-HDRCORRUPT

3-Error

Ucode header corrupted in [chars] found 0x[hec] expected 0x[hec]

-

-

"Reload the microcode. If the message recurs call your technical\n\ support representative for assistance."

UCODE-3-LDFAIL

3-Error

Unable to download ucode from [chars] in slot [dec] trying [chars] ucode

For some reason the microcode file specified by the configuration is\n\ not suitable for downloading or another error occurred. The onboard\n\ ROM microcode will be loaded so the interface can remain\n\ operational.

-

"Attempt to reload the microcode. If the message recurs call your\n\ technical support representative for assistance."

UCODE-3-NOFILE

3-Error

Ucode file [chars] not found system ucode loaded in slot [dec]

The file specified by the configuration was not found in Flash. The\n\ onboard ROM microcode will be loaded so the interface can remain\n\ operational.

-

"Use show flash to determine if the file is located in Flash. If the\n\ file is there attempt to reload the microcode. If the message recurs\n\ call your technical support representative for assistance."

UCODE-3-BADHWVER

3-Error

Ucode file [chars] requires [chars] version [dec].x hardware

A mismatch was detected during an attempt to load a microcode file\n\ into an interface processor. The hardware requires a different version\n\ than the one specified.

-

"Use the required microcode version."

UCODE-3-RDFAIL

3-Error

Unable to read ucode file [chars] from flash

For some reason the microcode file was not read from Flash. Flash\n\ might be locked by another process or otherwise unavailable.

-

"Use the show flash command to determine whether Flash is in use and\n\ issue another microcode reload when Flash is free. If the message\n\ recurs call your technical support representative for assistance."

UCODE-3-TOOBIG

3-Error

File [chars] at length [dec] is too long for buffer size [dec]

The file is too large for the buffer. The onboard ROM microcode will\n\ be loaded.

-

"If the error message recurs after the onboard ROM microcode is loaded\n\ call your technical support representative for assistance."

UCODE-3-WRONGHARD

3-Error

[chars] is [chars] ucode not [chars] microcode/hardware mismatch

The specified microcode file is for a different interface processor\n\ than specified in the configuration. The user has made a configuration\n\ error. The onboard ROM microcode will be loaded.

-

"Reenter your microcode configuration command after confirming the\n\ interface type and reload the microcode."

UCODE-5-OBSOLETE

5-Notice

FDDI unit [dec] has obsolete microcode: please upgrade it

This message occurs when an FDDI interface processor is found running\n\ microcode that does not support microcode CMT which is required for\n\ all software releases from 10.2 on.

-

"Upgrade the microcode on the interface processor."

UCODE-3-VERSIONCK

3-Error

Inappropriate version [dec].[dec] for [chars]

An attempt was made to load an inappropriate version of microcode.

-

"Copy the message exactly as it appears and report it your technical\n\ support representative."

UCODE-3-NOBUF

3-Error

Unable to allocate memory for ucode buffer

A buffer is required to decompress microcode before loading it into an\n\ interface processor. This buffer could not be allocated for some\n\ reason.

-

"Copy the message exactly as it appears and report it your technical\n\ support representative."

UCODE-3-NOMEMORY

3-Error

Unable to allocate memory during microcode reload

An attempt at memory allocation failed while downloading microcode \n\ to Interface processor.

-

"Copy the message exactly as it appears and report it your technical\n\ support representative."

UCODE-3-NOROM

3-Error

Invalid attempt to load ROM ucode in slot [dec]

Some interface processors cannot load microcode from ROM.

-

"Remove the erroneous configuration statement."

UCODE-3-IPCINITFAIL

3-Error

Unable to initialize IPC [chars] services

-

-

"Certain Interface Processors will not load properly. The router must\n\ be reloaded to clear the problem."

UCODE-3-IPCBUFFAIL

3-Error

Unable to obtain IPC resources

-

-

"Certain interface processors will not load properly. Try the reload\n\ command again. If this message recurs call your technical support\n\ representative for assistance."

UCODE-3-IPCINVALID

3-Error

Invalid IPC request [dec] received from [hec]

-

-

"Verify that the proper revisions of code are selected."

UCODE-3-SRCTYPE

3-Error

Invalid Ucode source type [dec]

Microcode source type as specified is not supported on the\n\ given platform

-

"Verify that the proper revisions of code are selected."

SYSMGT_RPC-3-IPC_ERROR

3-Error

SYSMGT RPC - IPC [chars] [chars] failed [chars]

System Management Remote Procedure Call operation failure. Request for\n\ information from the CIP card will not be processed.

-

LOG_STD_ACTION

SYSMGT_RPC-3-NETMGT_EVENT

3-Error

SYSMGT RPC - NETMGT Event: [chars] [dec]

System Management Remote Procedure Call Network management event error\n\ detected.

-

LOG_STD_ACTION

SYSMGT_RPC-3-RPC_ERROR

3-Error

SYSMGT RPC - RPC [chars] [chars] failed [chars] [dec]

System Management Remote Procedure Call operation failure. Request for\n\ information from the CIP card will not be processed.

-

LOG_STD_SH_TECH_ACTION

CMCC-3-RSETFAIL

3-Error

Interface [chars]: Error %-04x [chars]

An error occurred sending an interface enable or disable command.

cip

"The interface was reset by the software and the condition " "rectified. If that did not occur then issue the " "<Bold>debug channel events<NoBold> command and " "try each of the following tasks in sequence. If an action " "corrects the problem the remaining tasks do not need to be " "performed.\n" "<Bullet><par>Clear the interface using the <Bold>clear interface<NoBold> " "command. " "<Bullet><par>Reload the microcode. " "<Bullet><par>Reload the router.\n" "<Body><par>If the error still occurs copy the error message exactly " "as it appears. Record the output from the following commands:\n" "<Bullet><par><Bold>show tech <NoBold> " "<Bullet><par><Bold>show log <NoBold>\n" "<Body><par>Provide this information to your technical support " "representative."

CMCC-6-ADAPTERCHNG

6-Information

Interface [chars]: adapter type changed from [chars] to [chars]

The <Bold> channel-protocol <NoBold> configuration command sent after a reset failed to complete successfully.

cip

"The channel data transfer rate was reset to the default value. Reissue " "the configuration command."

CMCC-4-CFGFAIL

4-Warning

Interface [chars]: configuration command [chars] [chars] failed

An encapsulated control message had a size smaller than the minimum expected size. The message was dropped.

cip

LOG_STD_SH_TECH_ACTION

CMCC-3-UNKENCAP

3-Error

Interface [chars]: unknown encapsulated msg[dec] len[dec]

-

-

-

CMCC-3-CFGCMDDROPPED

3-Error

Config queue is full command was dropped slot [dec]

Sending a config command was retried. The receiving queues were still full after retries therefore the command was dropped.

cip

"Issue the<Bold>debug channel events<NoBold> command and " "try each of the following tasks in sequence. If an action " "corrects the problem the remaining tasks do not need to be " "performed.\n" "<Bullet><par>Reissue the configuration command. " "<Bullet><par>Clear the interface using the <Bold>clear interface<NoBold> " "command. " "<Bullet><par>Reload the microcode. " "<Bullet><par>Reload the router.\n" "<Body><par>If the error still occurs copy the error message exactly " "as it appears. Record the output from the following commands:\n" "<Bullet><par><Bold>show tech <NoBold> " "<Bullet><par><Bold>show log <NoBold>\n" "<Body><par>Provide this information to your technical support " "representative."

CMCC-3-IPCINITFAIL

3-Error

Unable to initialize IPC [chars] services

The InterProcess Communication IPC service used by the TN3270

-

"The CMCC will not load properly. The router must be reloaded to clear " "the problem."

CMCC-3-IPCBUFFAIL

3-Error

Unable to obtain IPC resources

The InterProcess Communication IPC service used by the TN3270

-

"The CMCC will not load properly. Try the reload command again. If " "this message recurs call your technical support representative for " "assistance."

CMCC-3-IPCINVALID

3-Error

Invalid IPC request [dec] received from [hec]

The InterProcess Communication IPC service used by the TN3270

-

"Verify that the proper revisions of code are selected."

CMCC-3-IPCDNSFAIL

3-Error

DNS lookup failed - [chars]

The InterProcess Communication IPC service used by the TN3270

-

"Verify that the proper revisions of code are selected."

CMCC-4-IPCDNSNOIPADDR

4-Warning

DNS lookup failed - the DNS server has no entry for hostname [chars]

The InterProcess Communication IPC service used by the TN3270

-

"Verify that the DNS server entries are up to date."

CMCC-5-IPCDNSSERVERUNREACHABLE

5-Notice

DNS lookup failed - DNS server [inet] is unreachable

The InterProcess Communication IPC service used by the TN3270

-

"Check for available routes to DNS servers."

CMCC-5-IPCDNSQUERYTIMEDOUT

5-Notice

DNS lookup failed - query to DNS server [chars] timed out

The InterProcess Communication IPC service used by the TN3270

-

"Check the status of the DNS server."

MEMPOOL-3-IPC

3-Error

[chars] [chars]

An IPC error has occurred on polling the Enhanced MempoolMIB

-

"Copy the error message exactly as it appears on the\n\ console or in the system log contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

CIPDUMP-3-CIP_CORE_DUMP_ERROR

3-Error

CIP core dump error slot [dec]: [chars]

An error occured during a CIP core dump

-

"None."

CIPDUMP-6-CIP_CORE_DUMP_PROGRESS

6-Information

Dump of slot [dec] core [chars].

Progress messages for CIP core dump.

-

"None."

SLOT_FPD-3-SUBBLOCK

3-Error

Failed to [chars] FPD subblock in Slot [dec].

Failed to create delete or populate a FPD subblock due to operation error.

-

LOG_STD_ACTION

SLOT_FPD-3-GETVER_FAILED

3-Error

Failed to get FPD version for FPD=[dec] in Slot [dec]: [chars].

Failed to get FPD version due to either IPC problem or operation error. The card will be disabled.

-

"Check module seating and module status. " "Ensure compatibility among FPD and IOS by comparing output of command " "<CmdBold>show hw-module slot fpd<NoCmdBold> with IOS Release Notes. " "Obtain IOS version by command <CmdBold>show version<NoCmdBold>."

SLOT_FPD-3-GETHWVER_FAILED

3-Error

Failed to get [chars] hardware revision number in Slot [dec].

Failed to get the board's revision number.

-

"Check module seating and module status. " "Re-insert the module. Contact TAC if this message is seen again."

SLOT_FPD-3-UPGRADE_FAILED

3-Error

Failed to upgrade FPD for slot [dec] [chars].

The FPD image upgrade operation failed. The cause could be a wrong image file error in accessing fpga storage physical interrupt such as power failure or card removal. Depending on the slot type and error cause the card could be in an unusable state. Normally the system automatically reattempts the upgrade and shuts the card after repeated failures.

-

"Do not interrupt the system while an FPD " "upgrade is in progress. Obtain the matching FPD package. Refer " "to IOS Release Notes for more information on obtaining the correct " "FPD package for the card. Review the output of the RP FPD logs."

SLOT_FPD-4-UPGRADE_STATE

4-Warning

[chars] on slot [dec].

Display the upgrade state

-

LOG_STD_RECUR_ACTION

SSE-3-BADMEMORY

3-Error

SSE memory failure detected orig [hex] [hex] tested [hex] [hex]

A memory error occurred.

-

LOG_STD_SH_TECH_ACTION

SSE-2-BOGUSEQ

2-Critical

SSE bogus equal branch [hex] [hex] [dec] [hec]

An internal inconsistency in the data structures used by the SSE occurred.

-

LOG_STD_SH_TECH_ACTION

SSE-3-COMPERR

3-Error

SSE compilation failure -- [chars]

A software failure occurred.

-

LOG_STD_SH_TECH_ACTION

SSE-2-HUNG

2-Critical

SSE hung -- [chars]

The SSE is hung.

-

"Reboot the SSE."

SSE-2-HWFAILURE

2-Critical

SSE hardware failure -- [chars] code [hex]

A hardware error occurred indicating an unexpected condition on the silicon switch processor SSP board.

-

"It might be necessary to replace the SSP. " LOG_STD_SH_TECH_ACTION

SSE-2-MEMERROR

2-Critical

SSE memory failure address [hex]\n expected [hex] got [hex]

A hardware error occurred indicating memory failure on the silicon switch processor SSP board.

-

"It might be necessary to replace the SSP. " LOG_STD_SH_TECH_ACTION

SSE-2-NESTADDR

2-Critical

SSE nested addresses detected protocol [dec] [inet]

An internal inconsistency in the data structures used by the SSE occurred.

-

LOG_STD_SH_TECH_ACTION

SSE-2-NOMATCH

2-Critical

SSE delete didn't end at a match node type [chars] value [dec] address [inet] bytecount [dec] high [dec] state [dec]

An internal inconsistency in the data structures used by the SSE occurred.

-

LOG_STD_SH_TECH_ACTION

SSE-2-NOMEMORY

2-Critical

No memory available for [chars]

An operation could not be accomplished because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions warrant upgrade to a larger memory configuration."

SSE-2-NOTZERO

2-Critical

program memory does not start at zero

A hardware error occurred indicating an unexpected condition on the silicon switch processor SSP board.

-

"It might be necessary to replace the SSP. " LOG_STD_SH_TECH_ACTION

SSE-2-SWFAILURE

2-Critical

SSE software failure -- [chars] [hex]

A software failure occurred.

-

LOG_STD_SH_TECH_ACTION

POSLC-1-INITFAIL

1-Alert

POSLC[dec]/[dec] initialization timeout failure

LC POS ASIC and framer initialization failed

poslc

"Copy the error message exactly as it appears on the \n\ console or in the system log. If you cannot determine \n\ the nature of the error from the error message text \n\ call your Cisco technical support representative and \n\ provide the \n\ representative with the gathered information."

POSLC-3-RXPOSTO

3-Error

POSLC[dec]/[dec] RX POS engine shutdown failed

The software is trying to shutdown the Rx POS engine. POS\n\ engine refuses to shutdown the software timeout

poslc

-

POSLC-3-TXPOSTO

3-Error

POSLC[dec]/[dec] TX POS engine shutdown failed

The software is trying to shutdown the Tx POS engine. POS \n\ engine refuses to shutdown the software timeout

poslc

-

POSLC-3-LINKPROC

3-Error

POSLC lcpos_link_report process: Could not get argument

LC POS link report process stops working

poslc

"Copy the error message exactly as it appears on the \n\ console or in the system log. Issue the show subsys show\n\ memory summary commands to gather data that may provide \n\ information to determine the nature of the error. If you \n\ cannot determine the nature of the error from the error \n\ message text or from the show subsys show memory summary \n\ output call your Cisco technical support representative \n\ and provide the representative with the gathered \n\ information."

POSLC-3-LINKBADEVT

3-Error

Unexpected event woke up LC POS link process.

LC POS link report process receives an unexpected event

poslc

"Copy the error message exactly as it appears on the \n\ console or in the system log. Issue the show subsys \n\ command to gather data that may provide information\n\ to determine the nature of the error. If you cannot \n\ determine the nature of the error from the error \n\ message text or from the show subsys output call your\n\ Cisco technical support representative and provide the \n\ representative with the gathered information."

POSLC-3-LINKNOPRC

3-Error

POSLC lcpos_add_process: Unable to create \n\ lcpos_link_report process

LC POS link report process can not be created

poslc

"Copy the error message exactly as it appears on the \n\ console or in the system log. Issue the show subsys \n\ command to gather data that may provide information\n\ to determine the nature of the error. If you cannot \n\ determine the nature of the error from the error \n\ message text or from the show subsys output call your\n\ Cisco technical support representative and provide the \n\ representative with the gathered information."

POSLC-3-BMAPAR

3-Error

[chars] POS [chars]. BMA_DATA[3:0]=0x[hec]. src=0x[hec] det1=0x[hec] det2=0x[hec]

Parity error occurred on POS asic BMA engine

poslc

-

POSLC-3-SRAMPAR

3-Error

[chars] POS [chars]. [chars]=0x[hec][chars]. src=0x[hec] det1=0x[hec] det2=0x[hec]

Parity error occurred on POS asic SRAM

poslc

-

POSLC-3-BMAENG

3-Error

[chars] POS [chars] [chars][chars]. src=0x[hec] det1=0x[hec] det2=0x[hec]

POS BMA engine hardware errors

poslc

-

POSLC-3-POSENG

3-Error

[chars] POS [chars]. [chars] port [dec]. src=0x[hec] det1=0x[hec] det2=0x[hec]

POS engine hardware errors

poslc

-

POSLC-3-SOP

3-Error

[chars] SOP. source=0x[hec] halt_minor0=0x[hec]

SOP hardware errors

poslc

-

POSLC-3-4302

3-Error

Runaway Skystone 4302 framer [dec] Tx [chars] counter byte=[dec] pkt=[dec].

4302 hardware errors

poslc

"Copy the error message exactly as it appears on the console \n\ or in the system log. Call your Cisco technical support \n\ representative and provide the representative \n\ with the gathered information."

POSLC-3-APS

3-Error

APS[dec] [chars]

RP deadman timer expired on LC LC is sending LAIS to far end

poslc

"Copy the error message exactly as it appears on the console \n\ or in the system log. Call your Cisco technical support \n\ representative and provide the representative \n\ with the gathered information."

POSLC-3-PROCESS_TIMEREVENT

3-Error

[chars]

An unexpected process timer event occurred in the Optical Services Module.

poslc

LOG_STD_ACTION

POSLC-3-UNEXPECTED_PROCESSEVENT

3-Error

[chars]

An unexpected process event occurred in the Optical Services Module.

poslc

LOG_STD_ACTION

POSLC-3-PROCESS_CREATEFAIL

3-Error

[chars]

The PoS line card could not create a process required for its operation. This condition might be caused by a resource being unavailable.

poslc

LOG_STD_ACTION

POSLC-3-HWERROR

3-Error

[chars]

The Optical Services Module has encountered a hardware error.

poslc

LOG_STD_ACTION

POSLC-3-UNKNOWN_CONTROLLER

3-Error

[chars]

An unknown controller condition was detected by the PoS line card while the controller was being analyzed.

poslc

LOG_STD_ACTION

POSLC-3-CORRUPT

3-Error

[chars]

A NULL SERIAL or SONET subblock retrieved while trying to fetch SERIAL or SONET subblock

poslc osm-pos

LOG_STD_ACTION

CM622_CM155-4-VCCMD

4-Warning

[dec]/[dec] VC:[dec] [chars] error cause: [chars]

CM622/CM155 ATM SAR VC operation error.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-VCTYPE

4-Warning

[dec]/[dec] VC:[dec] unsupported vc encapsulation type=[dec]

CM622/CM155 ATM SAR VC operation error.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-VCCLOSE

4-Warning

[dec]/[dec] VC:[dec] is close pending

The VC is in the TX SAR close pending state.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-RPCMD

4-Warning

[dec]/[dec] [chars] command error: [chars]

Linecard ATM driver handles RP command errors.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-OP

4-Warning

Error: [dec]/[dec] [chars]

Linecard ATM driver general operation errors.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-FRMROP

4-Warning

Error: [dec]/[dec] [chars] value=0x%04x

Linecard ATM driver framer operation errors.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-SAROP

4-Warning

Port [dec]: [chars] SAR doing [chars] error: [chars]

Linecard ATM driver SAR operation error.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-TXSARIND

4-Warning

Port [dec]: TX SAR [chars] command error: [chars] indication=0x%08x

Linecard ATM driver TX SAR indication error.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-RXSARIND

4-Warning

[dec]/[dec] RX SAR doing [chars] error: [chars] indication=0x%08x 0x%08x 0x%08x

Linecard ATM driver RX SAR indication errors.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-FWCKSUM

4-Warning

Port [dec]: [chars] SAR firmware selftest failure expected 0x%04x obtained 0x%04x

Linecard ATM SAR firmware checksum errors.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CM622_CM155-4-ATMCLKINT

4-Warning

[dec]/[dec] ATM Clock Internal Set on [dec]/[dec] too

CM155 ATM Clock Internal is enabled for the other channel \ on the same framer too the framer defines one bit for \ both channels.

gsr

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MEM_ECC-2-MALLOC

2-Critical

Attempt to malloc [dec] bytes for the ECC error log failed.\n ECC errors will only be reported and not recorded.\n

Malloc for the ECC error log failed. If system has only 32Mbytes of memory an upgrade would be advisable or is recommended.

-

LOG_STD_ACTION

MEM_ECC-2-MBE

2-Critical

Multiple bit error detected at 0x%08x

A multi-bit uncorrectable error was detected on a CPU read from DRAM.

-

LOG_STD_ACTION

MEM_ECC-2-MBE_RMW

2-Critical

Multiple bit error detected\nat 0x%08x on a read-modify-write cycle

A multi-bit uncorrectable error was detected during a read-modify- write cycle on a CPU read from DRAM for a non 8-byte access.

-

LOG_STD_ACTION

MEM_ECC-3-SYNDROME_MBE

3-Error

8-bit Syndrome for the detected Multi-bit error: 0x[hec]

The 8-bit syndrome for detected Multi-bit error. This value does not indicate the exact positions of the bits in error but can be used to approximate their positions.

-

LOG_STD_ACTION

MEM_ECC-2-PARITY

2-Critical

Parity error on CPU write to address: 0x%08x

Bad parity on data was detected by the ECC Ctrl during a CPU write operation.

-

LOG_STD_ACTION

MEM_ECC-2-PARITY_INFO

2-Critical

Parity error was detected on the \nfollowing bytes of a double word: [chars] [chars] [chars]

Indicates which bytes of a 64 bit word had bad parity that caused the ECC Ctrl to generated an interrupt.

-

LOG_STD_ACTION

MEM_ECC-3-SBE

3-Error

Single bit error detected and corrected at 0x%08x

A single-bit correctable error was detected on a read from DRAM. 'show ecc' can be used to dump Single-bit errors logged thus far.

-

LOG_STD_ACTION

MEM_ECC-3-SBE_RMW

3-Error

Single bit error detected and corrected at\n0x%08x on a read-modify-write cycle

A single-bit correctable error was detected on during a read-modify- write cycle on a CPU read from DRAM for a non 8-byte access. 'show ecc' can be used to dump Single-bit errors logged thus far.

-

LOG_STD_ACTION

MEM_ECC-3-SBE_RMW_HARD

3-Error

Single bit *hard* error detected at\n0x%08x on a read-modify-write cycle

A single-bit uncorrectable hard error was detected during a read-modify- write cycle on a CPU read from DRAM for a non 8-byte access. <CmdBold>show ecc<noCmdBold> can be used to dump Single-bit errors logged thus far.

rsp gsr-diags

"Monitor system through <CmdBold>show ecc<noCmdBold> and replace DRAM" " if too many such errors occur."

MEM_ECC-3-SBE_HARD

3-Error

Single bit *hard* error detected at 0x%08x

A single-bit uncorrectable error [hard error] was detected on a CPU read from DRAM. 'show ecc' will dump the Single-bit errors logged thus far and will also indicate detected hard error address locations.

-

"Monitor system through 'show ecc' and replace DRAM if too many such errors."

MEM_ECC-3-SBE_LIMIT

3-Error

Single bit error detected and corrected\nat 0x%08x

A single-bit correctable error was detected on a CPU read from DRAM.

-

LOG_STD_ACTION

MEM_ECC-3-SBE_RMW_LIMIT

3-Error

Single bit error detected and corrected at 0x%08x on a read-modify-write cycle

A single-bit correctable error was detected on during a read-modify- write cycle on a CPU read from DRAM for a non 8-byte access. 'show ecc' can be used to dump Single-bit errors logged thus far.

-

LOG_STD_ACTION

MEM_ECC-3-SYNDROME_SBE

3-Error

8-bit Syndrome for the detected Single-bit error: 0x[hec]

The 8-bit syndrome for detected single-bit error. This value does not indicate the exact positions of the bits in error but can be used to approximate their positions.

-

LOG_STD_ACTION

MEM_ECC-3-SYNDROME_SBE_LIMIT

3-Error

8-bit Syndrome for the detected Single-bit error: 0x[hec]

The 8-bit syndrome for detected single-bit error. This value does not indicate the exact positions of the bits in error but can be used to approximate their positions.

-

LOG_STD_ACTION

MEM_ECC-3-BADADDR_SBE

3-Error

Invalid SBE dram address: 0x%08x latched by ECC Ctrl

The address latched by the ECC Ctrl when detecting a SBE is not a valid dram address. This kind of an error is not one that the ECC Ctrl shouldn't report under its normal operating conditions and when it does it most probably indicates a malfunctioning ECC Ctrl that needs replacement.

-

LOG_STD_ACTION

MEM_ECC-3-BADADDR_SBE_RMW

3-Error

Invalid SBE dram address: 0x%08x latched by ECC Ctrl\n during a RMW cycle

The address latched by the ECC Ctrl when detecting an SBE during a Read-Modify-Write cycle isn't a valid dram address. This kind of an error is not one that the ECC Ctrl shouldn't report under its normal operating conditions and when it does it most probably indicates a malfunctioning ECC Ctrl that needs replacement.

-

LOG_STD_ACTION

MEM_ECC-3-BADADDR_MBE

3-Error

Invalid MBE dram address: 0x%08x latched by ECC Ctrl

The address latched by the ECC Ctrl when detecting an MBE is not a valid dram address. This kind of an error is not one that the ECC Ctrl shouldn't report under its normal operating conditions and when it does it most probably indicates a malfunctioning ECC Ctrl that needs replacement.

-

LOG_STD_ACTION

MEM_ECC-3-BADADDR_MBE_RMW

3-Error

Invalid MBE dram address: 0x%08x latched by ECC Ctrl\n during a RMW cycle

The address latched by the ECC Ctrl when detecting an MBE during a Read-Modify-Write cycle isn't a valid dram address. This kind of an error is not one that the ECC Ctrl shouldn't report under its normal operating conditions and when it does it most probably indicates a malfunctioning ECC Ctrl that needs replacement.

-

LOG_STD_ACTION

SONETMIB-1-LOSTUPDATE

1-Alert

Lost raw stats update for if_index=[dec]

-

-

""

SONETMIB-1-MALLOCNEW

1-Alert

Malloc failed for new interface=[dec]

Unable to allocate enough memory to create SONET MIB structure\n\ for new interface.

-

LOG_STD_NO_ACTION

SONETMIB-1-DELETE

1-Alert

could not delete interface if_index=[dec]

The specified interface was not successfully dequeued.

-

LOG_STD_NO_ACTION

SONETMIB-3-NULLCFGPTR

3-Error

NULL SONET MIB config pointer if_index=[dec]

Attempted to initialize the SONET MIB using a NULL pointer.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

X40G_LOWQ-5-MAX_QUEUE_LIMIT_EXCEEDED

5-Notice

Number of queues [dec] for the Low queue sub-block exceeded the

More queues cannot be created on the interface since the number of low queues created in the system exceeds the maximum allowed limit of 16.

c7600-es-platform

"This is just a informational message and the configuration should fail " "to apply on the interface. Please check the output of show platform lowq" "for more information"

HSRP-3-NOSOCKET

3-Error

Unable to open socket

The system was unable to initialize an IP connection for the Hot Standby protocol.

hsrp

"Make sure that there is at least one interface configured to run " "IP."

HSRP-4-BADAUTH

4-Warning

Bad authentication from [chars] group [dec] remote state [chars]

Two routers participating in HSRP disagree on the valid authentication string.

hsrp

"Use the standby authentication command to repair the HSRP authentication \n\ discrepancy between the local system and the one whose IP address \n\ is reported."

HSRP-4-BADAUTH2

4-Warning

Bad authentication from [chars]

Two routers participating in HSRP disagree on the valid authentication string.

hsrp

"Use the standby authentication command to repair the HSRP authentication " "discrepancy between the local system and the one whose IP address " "is reported."

HSRP-3-MISCONFIG

3-Error

Attempt to change [chars] MAC address to [enet] when DECNET already running

An HSRP group attempted to become active on an interface that can only support a single MAC address and which is running DECnet. If standby use-bia is not configured then HSRP would normally set the interface MAC address to the HSRP virtual MAC address but this is not allowed if DECnet is running.

hsrp

"Enable standby use-bia on the interface."

HSRP-5-STATECHANGE

5-Notice

[chars] Grp [dec] state [chars] -> [chars]

The router has changed state

hsrp

LOG_STD_NO_ACTION

HSRP-4-DUPADDR

4-Warning

Duplicate address [chars] on [chars] sourced by [enet]

The IP address in an HSRP message received on the specified interface is the same as the IP address of the router. Another router might be configured with the same IP address. The most likely cause is a network loop or a misconfigured switch that is causing the router to see its own HSRP Hello messages.

hsrp

"Check the configurations on all the HSRP routers to ensure " "that the interface IP addresses are unique. Check that no " "network loops exist. If port channels are configured check " "that the switch is correctly configured for port-channels. " "Enable standby use-bia so that the error message displays " "the interface MAC address of the sending router. This can " "be used to determine if the error message is caused by a " "misconfigured router or a network loop."

HSRP-4-DUPVIP1

4-Warning

[chars] Grp [dec] address [chars] is already assigned to [chars] group [dec]

The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to a different HSRP group.

hsrp

"Check the configuration on all HSRP routers and ensure " "that the virtual IP address of each HSRP group is unique."

HSRP-4-DUPVIP2

4-Warning

[chars] Grp [dec] address [chars] is already assigned on this interface

The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to this interface.

hsrp

"Check the configuration on all HSRP routers and ensure " "that the virtual IP address of each HSRP group is unique."

HSRP-4-DUPVIP3

4-Warning

[chars] Grp [dec] address [chars] is already assigned to or overlaps with an address on another interface or application

The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to or overlaps with an address on another interface or application.

hsrp

"Check the configuration on all HSRP routers and ensure " "that the virtual IP address of each HSRP group is unique."

HSRP-4-BADVIP

4-Warning

[chars] Grp [dec] address [chars] is in the wrong subnet for this interface

The HSRP virtual IP address contained in the Hello message cannot be learnt as it is not within a subnet configured on the interface.

hsrp

"Check the configuration on all HSRP routers and ensure " "that the virtual IP address is within a configured subnet."

HSRP-4-DIFFVIP1

4-Warning

[chars] Grp [dec] active routers virtual IP address [chars] is different to the locally configured address [chars]

The HSRP virtual IP address contained in the Hello message from the Active router is different from the virtual IP address configured locally.

hsrp

"Check the configuration on all HSRP routers in the group " "and ensure they are all configured with the same virtual " "IP address."

HTTP-3-PROC_NOCREAT

3-Error

\ Unable to create HTTP process.

An error occurred during initialization of the HTTP process. The HTTP process that processes all HTTP requests and responses could not be created.

-

"Reduce other system activity to ease memory demands. If " "conditions warrant upgrade to a larger memory configuration. "

HTTP-4-SERVER_CONN_RATE_EXCEED

4-Warning

\ Number of connections per minute has exceeded the maximum limit[dec]

The message indicates that the current number of connections requested per minute has exceeded the limit specified by the platform. HTTP server will resume accepting the connections 15 seconds from the time the message is issued. This restriction is done as per the HTTP throttling functionality.

http

"Reduce connection rate to the server."

HTTP-3-OUTOF_MEM

3-Error

\ HTTP out of memory.

An error occurred during initialization of the HTTP process. The HTTP process could not create crucial internal data structures that are required for operation of the HTTP subsystem. The most likely reason for this condition is an exhaustion of system memory.

http

"Reduce other system activity to ease memory demands. if " "conditions warrant upgrade to a larger memory configuration. "

HTTP-3-INIT_FAIL

3-Error

\ HTTP Process Init failed.

Initialization of the HTTP Subsystem has failed

http

"Reduce other system activity to ease memory demands. If " "conditions warrant upgrade to a larger memory configuration. "

HTTP-6-SERVER_SETUP_FAILED

6-Information

\ Server setup failed

Setup of the HTTPS server to listen on the specified port number has failed.

http

"Disable the server verify that port number is correct " "and enable the server." "Reduce other system activity to ease memory demands. If " "conditions warrant upgrade to a larger memory configuration. "

LCB-3-LOCKFAILURE

3-Error

Multiple LCB event processes scheduled

This message occurs when LCB event process fails to lock the\n\ semaphore which is used to prevent multiple LCB processes from \n\ running. This implies that multiple LCB processes have been \n\ scheduled to run which should not happen

-

"Try executing the command again after a few minutes. If the problem\n\ persists contact Cisco Technical support"

LCB-3-QUEUEFAILURE

3-Error

LCB process unable to create event queue

Unable to create LCB event queue. LCB process quit. The operating\n\ system was unable to allocate RAM space for the queue

-

"Try executing the command again after a few minutes. If the problem\n\ persists it indicates a lack of RAM space. Most likely the router \n\ image requires more system memory RAM than the router contains."

LANMGR-4-OLDTRAMON

4-Warning

Cannot run RPS on [chars] Old TRAMON code.

The software on this interface cannot support the functions required\n\ for LAN Network Manager.

-

"Call your Cisco technical support representative about a\n\ firmware upgrade for this interface card."

LANMGR-4-BADRNGNUM

4-Warning

Ring number mismatch on [chars] shutting down the interface

-

-

"Check all bridges connected to this Token Ring and ensure that they\n\ are using the same assigned ring number."

LANMGR-4-BADUPCALL

4-Warning

Unexpected call [chars] from LLC2 for Bridge %03x-[hec]-%03x

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

LANMGR-4-NORING

4-Warning

No ring info for [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

LANMGR-2-NOMEMORY

2-Critical

No memory available: [chars]

The requested operation failed because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

LNMC-3-BADCLSIIND

3-Error

[chars] Invalid indication [chars] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSIRET

3-Error

[chars] Invalid ret code 0x[hec] [chars] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSICNF

3-Error

[chars] Invalid confirm [chars] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSI

3-Error

[chars] primitive not valid for lnm [chars] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSIIDTYPE

3-Error

[chars] Invalid ID type = 0x[hec] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION_ERR

LNMC-3-BADCLSIPRIMTYPE

3-Error

[chars] Invalid primitive type = 0x[hec] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSIHDRLEN

3-Error

[chars] Bad header len = 0x[hec] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSIDATALEN

3-Error

[chars] Bad data len = [dec] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

LNMC-3-BADCLSISAP

3-Error

[chars] Bad clsi SAP id = [hec] [chars]

A LAN network manager system error occurred.

-

LOG_STD_ACTION

CLSDR-3-NOINIT

3-Error

CLSDRIVER not initialized

A CLSDRIVER initialization failed earlier. Trying to use the driver\n\ now results in an error condition.

-

-

CLSDR-3-NOREMOVEPORT

3-Error

RemovePort: port 0x[hec] not on list

-

-

LOG_STD_ACTION

CLSDR-3-NOREMOVECEP

3-Error

RemoveCep : Cep 0x[hec] not on list

-

-

LOG_STD_ACTION

CLSDR-3-NODLUCREATE

3-Error

Cannot create DLU for this type [dec]

-

-

LOG_STD_ACTION

CLSDR-3-NOPORTCREATE

3-Error

Cannot create PORT structure

The CLSDRIVER cannot enable this port for processing.

-

"Try rebooting the router. " LOG_STD_ACTION

CLSDR-3-NOCLSSERVER

3-Error

unable to start the Server process

Could not start the CLSDRIVER process possibly due to a resource\n\ problem. The subsystem using CLSDRIVER does not work.

-

-

CLSDR-3-INCORRECTPORT

3-Error

Incorrect port pointer in USapId

-

-

LOG_STD_ACTION

CLSDR-3-NOCEP

3-Error

Cannot found cep in free pool

A software or hardware error occurred.

-

LOG_STD_ACTION

CLSDR-3-WRONGMSG

3-Error

Should never be here cls message type unknown 0x[hec]

The CLS message type is unknown to the destination logical unit\n\ DLU.

-

LOG_STD_ACTION

CLSDR-3-MSGERR

3-Error

[chars] couldn't get a message

-

-

LOG_STD_ACTION

CLSDR-3-ERRRTN

3-Error

[chars] failed error 0x[hec]

-

-

"Refer to CLSI software documentation for more information about this\n\ error. Report this error to your technical support representative."

STUN-4-DUPROUTE

4-Warning

Cannot define duplicate route on the\n\ same group

This route command is defined on another interface belonging to the same group. Cannot define duplicate route on the same group

-

"Consider defining a new group and moving this " "interface onto that group"

STUN-4-PEERSTATE

4-Warning

Peer [chars] wrong state [dec] [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-3-BADMAGIC

3-Error

[chars]: wrong magic mine [hec] theirs [hec] [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-3-BADMAGICTCP

3-Error

[chars]: peer [chars] wrong magic mine [hec] theirs [hec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-3-BADLENOP

3-Error

[chars]: bad len or unknown op op [dec] len [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-6-TCPPEERSHUT

6-Information

[chars] [chars] [inet][dec]

This route closed a STUN connection with a remote peer.

-

"Examine this router to see why it closed this connection with this " "peer. This can be caused by normal events such as " "reconfiguration."

STUN-3-CONNILLSTATE

3-Error

CONN: Peer [chars] illegal state [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-3-BADCONN

3-Error

CONN: bad connection [dec] peer: [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-4-ERR

4-Warning

[chars]: [chars]: [chars] op [hec] len [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-3-SENDPUNT

3-Error

[chars]: sent [chars] to [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-3-SENDPUNTTCP

3-Error

[chars]: sent [chars] to [[dec]][inet]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-6-OPENING

6-Information

CONN: opening peer [chars] [dec]

A connection attempt to a remote peer completed successfully OPENED PASSIVE-OPEN or is in the process of being opened OPENING. This is

-

LOG_STD_NO_ACTION

STUN-6-CONNOPENFAIL

6-Information

CONN: peer [chars] open failed [chars] [[dec]]

An attempt to connect to a remote TCP STUN peer failed.

-

"Verify that the remote peer is accessible from this router that it is " "running software capable of supporting STUN and that it is configured " "correctly."

STUN-3-BADPASSIVEOPEN

3-Error

passive open from [inet][dec] -> [dec] failed

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

STUN-6-PASSIVEOPEN

6-Information

passive open [inet][dec] -> [dec]

A connection attempt to a remote peer completed successfully OPENED PASSIVE-OPEN or is in the process of being opened OPENING. This is

-

LOG_STD_NO_ACTION

STUN-6-TCPFINI

6-Information

peer [chars] closed [previous state [chars]]

A remote peer closed a STUN connection with this router.

-

"Examine the other router to see why it closed this connection with " "this peer. This can be caused by normal events such as " "reconfiguration."

STUN-6-PEERSHUTDOWN

6-Information

shutting down peer [chars] on [chars]

A connection to a remote peer is being shut down. This is typically the result of user intervention in STUN reconfiguration or disabling. This is good expected behavior.

-

LOG_STD_NO_ACTION

STUN-6-OPENED

6-Information

[chars]: peer [chars] opened [previous state [chars]]

A connection attempt to a remote peer completed successfully OPENED PASSIVE-OPEN or is in the process of being opened OPENING. This is

-

LOG_STD_NO_ACTION

STUN-3-NOINPIDB

3-Error

Input idb not set

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

STUN-6-RECONNECT

6-Information

PHDR: reconnect from peer [chars]

A remote peer reestablished a connection to this router.

-

LOG_STD_NO_ACTION

STUN-2-NOBUF

2-Critical

Interface [chars] no buffer available to [chars]

A memory shortage existed at the time that the configuration command was issued. This condition is rare and under normal conditions temporary.

-

"Reconfigure the STUN group. If memory shortages persist call your " "Cisco technical support representative for assistance."

STUN-2-NOTGI

2-Critical

Please remove and redefine protocol group [dec]

An internal error occurred. The configuration is irregular.

-

"Remove and reconfigure the STUN protocol group. Record the " "configuration and call your Cisco technical support " "representative for assistance."

STUN-2-NOMEMORY

2-Critical

No memory available: [chars]

The requested operation failed because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

SDLC-4-DROPPED

4-Warning

Dropped SDLC packet from SDLC hold queue

An SDLC frame had to be dropped from the output hold queue usually\n\ because of excessive congestion on the output link.

-

"If this message occurs frequently determine why your SDLC link is\n\ being overloaded with data and resolve the cause typically by either\n\ increasing bandwidth to your SDLC line or reducing the load on your\n\ link."

SDLC-3-NULLPAK

3-Error

Interface [chars] NULL packet ptr rvr [dec] vs [dec] vr [dec]

An internal software error occurred in the router's SDLC processing\n\ system.

-

LOG_STD_SH_TECH_ACTION

SDLC-3-NOINPIDB

3-Error

Input idb not set

This is a software error. A frame was given to the SDLC handler to\n\ process but the interface on which the frame arrived is not known.

-

LOG_STD_SH_TECH_ACTION

SDLC-4-FRAMEERR

4-Warning

Interface [chars] Frame error: CF [hex] VS [dec] [chars] VR [dec] Reason [hex]

A FRMR frame was received. This can be due to a noisy serial line an\n\ overloaded SDLC device or corrupted data.

-

"If this message recurs service the serial line and the devices\n\ attached to it."

SDLC-4-INFOBAD

4-Warning

Interface [chars] Info field not permitted

A bad SDLC frame was received.

-

"If this message recurs check the SDLC serial line and the\n\ devices attached to it."

SDLC-4-CTRLBAD

4-Warning

Interface [chars] Invalid control field

A bad SDLC frame was received.

-

"If this message recurs check the SDLC serial line and the devices\n\ attached to it."

SDLC-4-N1TOOBIG

4-Warning

Interface [chars] N1 too large

An information frame was received from the other end of the SDLC link\n\ that was larger than allowed with the N1 parameter on this link.

-

"Either increase the value of the N1 parameter for this interface on\n\ the router or reduce the size of the maximum information frame sent by\n\ the other end of the link."

SDLC-4-INVNR

4-Warning

Interface [chars] Invalid NR value

A bad SDLC frame was received.

-

"If this message recurs check the SDLC serial line and the\n\ devices attached to it."

SDLC-4-SDLC_ERR

4-Warning

SDLC_ERROR with no poll

A protocol error was detected on a secondary station but FRMR could\n\ not be sent because the station did not own the poll bit. This message\n\ indicates either poor line conditions or a faulty SDLC\n\ implementation.

-

"If this message recurs run traces on the SDLC line. Copy the error\n\ message exactly as it appears and report it to your technical support\n\ representative."

SDLC-2-ILLEGSTATE

2-Critical

[chars] illegal state for addr %02x [chars][dec]

An internal SDLC state violation was detected.

-

LOG_STD_SH_TECH_ACTION

SDLC-2-NOPOINTER

2-Critical

AW_SDLC_SEC with no sdllc_llc pointer.

An error condition occurred during SDLLC initiation.

-

"No action is required. The SDLLC session will restart without operator\n\ intervention."

SDLC-3-CONFIGERR

3-Error

[chars] addr %02x Sent SNRM received SNRM. Check link station roles.

A hardware or software error occurred.

-

LOG_STD_ACTION

SDLC-4-NOUA

4-Warning

[chars] addr %02x received command %02x in response to SNRM expected UA

The router received a frame other than a UA in response to a SNRM.

-

"Check the end station to see if the SNA stack is up and running."

SDLC-5-INVLDGRPPOLL

5-Notice

Interface [chars] not configured for group-poll frame received %02x

An unnumbered poll UP was received with the wrong group poll\n\msgdef_recommended_action Make sure the group poll address configured on the router matches the\n\ one configured in the physical unit macro

-

-

SDLC-4-INVLDGRPCFG

4-Warning

Interface [chars] ignoring group-poll mismatch UPOLL %02x

A hardware or software error occurred.

-

LOG_STD_ACTION

SDLC-4-BADFRAME

4-Warning

[chars] Received bad SDLC [chars]frame address %02x control %2X

A hardware or software error occurred.

-

LOG_STD_ACTION

SDLC-2-NOMEMORY

2-Critical

No memory available: [chars]

The requested operation failed because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

SDLC-3-DLU_ERROR

3-Error

[chars] DLU failed to close station %02x before re-opening [chars]/[chars]

A hardware or software error occurred.

-

LOG_STD_ACTION

SDLC-4-XID_NOMATCH

4-Warning

[chars] XID mismatch for %02x. CONNECTION REJECTED

-

-

"This is a security feature. Additional information is displayed to\n\ help trace the source of the rejected XID. If the message is\n\ undesirable simply remove the XID statement from the router\n\ configuration."

SDLC-6-XID_DISPLAY

6-Information

sa [enet] da [enet] ss [hec] ds [hec] [%02x%02x%02x%02x]

This message supplies the information for the received and rejected\n\ XID.

-

"See the "SDLC-6-XID_NOMATCH" error message."

SDLC-6-XID_FORMAT

6-Information

Unsupported XID format received format [dec]

-

-

"See the "SDLLC-6-XID_NOMATCH" error message."

SDLLC-5-ACT_LINK

5-Notice

SDLLC: [chars] LINK address %02x ACTIVATED: [chars]

An SDLLC media conversion session was activated.

-

LOG_STD_NO_ACTION

SDLLC-5-DACT_LINK

5-Notice

SDLLC: [chars] LINK address %02x DEACTIVATED: [chars]

An SDLLC media conversion session was deactivated. If deactivation is\n\ a result of an error condition this message will include a reason.

-

"If the message does not include a description of an error the\n\ deactivation was normal and the message is for information only. If the\n\ message does include a description of an error begin problem analysis.\n\ Determine whether session loss is related to LLC2 timers by issuing the\n\ debug llc2-err command. If the problem is related to LLC2 timers\n\ consider using SDLLC with the local acknowledgment feature. Copy the\n\ error message exactly as it appears and report it to your technical\n\ support representative."

TXCONN-3-BADLICENSEKEY

3-Error

Bad license key configured for Transaction Connection.

The license key configured with the txconn license configuration\n\ command is not valid.

txconn

"Check that the license key was entered correctly in the txconn\n\ license configuration command. Refer to the txconn feature documentation\n\ for information on how to obtain a valid license key."

TXCONN-3-BADMODE

3-Error

Unknown mode '[chars]' configured for server [chars]

The mode configured for the txconn server was rejected by the\n\ remote database server.

txconn

"Contact your SNA network administrator to determine the correct\n\ name of the mode to use to connect to DB2 on the remote database\n\ server."

TXCONN-3-BADRLU

3-Error

Bad remote LU '[chars]' configured for server [chars]

The remote LU configured for the txconn server is incorrect.

txconn

"Contact your SNA network administrator to determine the correct\n\ name of the remote LU for DB2 on the remote database server. Be sure to\n\ check that the SNA network name is correct as well as the LU name."

TXCONN-3-INVALIDTRANS

3-Error

Bad Transaction ID flushing out request for client [inet] connected server [chars] killing connection.

Bad input stream.

txconn

"This is an informational message. " LOG_STD_NO_ACTION

TXCONN-3-UNEXPECTEDREQ

3-Error

Unexpected client data flushing out the request for client [inet] connected server [chars].

Bad input stream.

txconn

"This is an informational message. " LOG_STD_NO_ACTION

TXCONN-3-NOSESSION

3-Error

Out of resource cannot create transaction for client [inet] connected server [chars] killing connection.

The router is out of memory.

txconn

"This is an informational message. " LOG_STD_NO_ACTION

TXCONN-3-TXEXCEPTION

3-Error

Exception [chars] from transaction [chars] to [chars] from client [inet]

An unexpected transaction error occurred.

txconn

LOG_STD_ACTION " If possible also provide the output of the debug txconn data\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared."

TXCONN-5-CONNIDLETIMEOUT

5-Notice

Client [inet] connected to server [chars] has timed out after %TE.

The client was idle for too long and the idle timeout configured\n\ for the txconn server expired.

txconn

"This is an informational message only. " LOG_STD_NO_ACTION

TXCONN-5-TRANSIDLETIMEOUT

5-Notice

Transaction [hec] of Client [inet] connected to server [chars] has timed out after %TE.

The transaction was idle for too long and the idle timeout configured\n\ for the txconn server expired.

txconn

"This is an informational message only. " LOG_STD_NO_ACTION

TXCONN-5-SECFAIL

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The userid and/or password passed in by the client were rejected by\n\ the remote database server.

txconn

"This is an informational message only. " LOG_STD_NO_ACTION

TXCONN-5-TARGETDOWN

5-Notice

CICS server [chars] has become unavailable. Recovery is in progress.

A CICS server for a configured destination has become unavailable. All client\n\ connections to this server will be rejected until it becomes available again.

txconn

"This is an informational message only. " LOG_STD_NO_ACTION

TXCONN-5-TARGETUP

5-Notice

CICS server [chars] is now available.

A CICS server that was previously unavailable has become available. All client\n\ connections to this server will now be accepted.

txconn

"This is an informational message only. " LOG_STD_NO_ACTION

CTRC-3-APPCVERB

3-Error

Unexpected APPC error: opcode %04x primary code %04x secondary code %08lx

An unexpected APPC error occurred. ctrc uses APPC API calls to\n\ SNASW to communicate with the remote database server. Opcode\n\ identifies the APPC API call that received the error. Primary and\n\ secondary return codes are returned by the APPC API.

ctrc

"This usually indicates a problem in the SNA network. Try the ctrc\n\ ping command to test connectivity to the remote database server. If\n\ the ctrc ping fails check the status of the SNA link to the\n\ remote database server with the show snasw link command. If the link\n\ is active try stopping and starting the link. If the problem persists\n\ contact your SNA network administrator for help in troubleshooting. " LOG_STD_RECUR_ACTION " If possible also provide the output of the debug ctrc appc\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared."

CTRC-3-APPCERROR

3-Error

[chars]

An APPC error occurred. ctrc uses APPC API calls to\n\ SNASW to communicate with the remote database server.

ctrc

"This usually indicates a problem in the SNA network. Try the ctrc\n\ ping command to test connectivity to the remote database server. If\n\ the ctrc ping fails check the status of the SNA link to the\n\ remote database server with the show snasw link command. If the link\n\ is active try stopping and starting the link. If the problem persists\n\ contact your SNA network administrator for help in troubleshooting. " LOG_STD_RECUR_ACTION " If possible also provide the output of the debug ctrc appc\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared."

CTRC-4-APPCWARN

4-Warning

[chars]

An APPC error occurred. ctrc uses APPC API calls to\n\ SNASW to communicate with the remote database server.

ctrc

"This usually indicates a temporary problem in the SNA network. Try the ctrc\n\ ping command to test connectivity to the remote database server. If\n\ the ctrc ping fails check the status of the SNA link to the\n\ remote database server with the show snasw link command. If the link\n\ is active try stopping and starting the link. If the problem persists\n\ contact your SNA network administrator for help in troubleshooting. " LOG_STD_RECUR_ACTION " If possible also provide the output of the debug ctrc appc\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared."

CTRC-3-SNASWNOTSTARTED

3-Error

SNASW is not started -- unable to connect to remote database.

A client connected to a ctrc server but ctrc was unable to\n\ connect out to the remote database because SNASW is not started.\n\ ctrc uses SNASW to connect to the remote database server. You\n\ must start SNASW before ctrc clients attempt to connect.

ctrc

"Start SNASW and retry the client connection."

CTRC-3-SNASWSTOPPED

3-Error

SNASW was stopped -- existing connections have been closed.

SNASW was stopped while ctrc connections were open. Stopping\n\ SNASW caused all open SNA connections to the remote database\n\ server to be lost. As a result all client connections were\n\ disconnected. You should not stop SNASW while there are open\n\ ctrc connections.

ctrc

"Restart SNASW. Disconnected clients must reconnect."

CTRC-3-NOBUFFS

3-Error

No buffers available to [chars]

CTRC attempted to allocate a buffer while performing the \n\ operation described in the message text. A buffer pool does \n\ not contain enough items to satisfy the allocation request.

ctrc

"This problem most commonly occurs whenever a public buffer \n\ pool runs out of elements. Determine the which pool has run\n\ out of buffers using the \"show buffers\" command. Adjust the\n\ pool size using the buffers configuration command."

DBCONN-3-BADLICENSEKEY

3-Error

Bad license key configured for Database Connection.

The license key configured with the dbconn license configuration\n\ command is not valid.

dbconn

"Check that the license key was entered correctly in the dbconn\n\ license configuration command. Refer to the dbconn feature documentation\n\ for information on how to obtain a valid license key."

DBCONN-3-LICENSEHWWARNING

3-Error

Number of connections for TXCONN and DBCONN is at 90%% license limit.

The number of allowed Database and Transaction Connection client \n\ in this system is reaching the limit.

dbconn

"Contact StarQuest Software to acquire more license."

DBCONN-3-LICENSEEXPWARNING

3-Error

License is about to expire for Database and Transaction Connection.

This system is using a temporary key for its Database and Transaction\n\ Connection. The license is about to expire.

dbconn

"Contact StarQuest Software to acquire a permanent key."

DBCONN-3-LICENSEEXPERROR

3-Error

License is expired for Database and Transaction Connection.

This system is using a temporary key for its Database and Transaction\n\ Connection. The license is expired.

dbconn

"Contact StarQuest Software to acquire a permanent key."

DBCONN-3-BADMODE

3-Error

Unknown mode '[chars]' configured for server [chars]

The mode configured for the dbconn server was rejected by the\n\ remote database server.

dbconn

"Contact your SNA network administrator to determine the correct\n\ name of the mode to use to connect to DB2 on the remote database\n\ server."

DBCONN-3-BADRLU

3-Error

Bad remote LU '[chars]' configured for server [chars]

The remote LU configured for the dbconn server is incorrect.

dbconn

"Contact your SNA network administrator to determine the correct\n\ name of the remote LU for DB2 on the remote database server. Be sure to\n\ check that the SNA network name is correct as well as the LU name."

DBCONN-3-BADTPNAME

3-Error

Bad TP name configured for server [chars]

The tpname configured for the dbconn server is not recognized by the\n\ remote database server.

dbconn

"Configure a TP name that is available on the remote database server.\n\ Most DB2 systems will accept the DRDA default TP name of \x076DB\n\ except for SQL/DS. Contact your SNA network administrator and/or\n\ your DB2 administrator to determine the TP name used by your DB2.\n\ To use the DRDA default do not explicitly configure a TP name for your\n\ dbconn server."

DBCONN-3-DRDASYNTAX

3-Error

DRDA protocol error from server [chars] SYNERRCD x'%02X'

An unexpected DRDA protocol error occurred between dbconn and the\n\ remote database server.

dbconn

LOG_STD_ACTION " If possible also provide the output of the debug dbconn drda\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared."

DBCONN-5-IDLETIMEOUT

5-Notice

Client [inet] connected to server [chars] has timed out after %TE.

The client was idle for too long and the idle timeout configured\n\ for the dbconn server expired.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-SECFAIL

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The userid and/or password passed in by the client were rejected by\n\ the remote database server.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-PWDEXPIRED

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The password passed in by the client was rejected by the remote database \n\ server because it's expired.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-PWDINVALID

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The password passed in by the client was rejected by the remote database \n\ server.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-PWDMISSING

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The remote database server requires a userid and password but the \n\ password was not provided.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-UIDREVOKED

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The userid used to connect to the remote database server has been revoked.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-UIDINVALID

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The userid used to connect to the remote database server is not valid.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-UIDMISSING

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

The remote database server requires a userid but the \n\ userid was not provided.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-SECUNKNOWN

5-Notice

APPC security failed client [inet] using userid '[chars]' for server [chars]

An unspecified security failure has occurred. The database host system may\n\ be able to provide more specific information.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-WLMMISMATCH

5-Notice

WLM transport type mismatch on server [chars].

The transport type within a server list received from a Workload Manager \n\ load balanced database does not match the transport type of the corresponding \n\ dbconn server. If the conflicting server list specifies SNA transport type the \n\ default mode #INTER will be used to establish the connection.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

DBCONN-5-WLMDOWN

5-Notice

All WLM routes on server [chars] have become unavailable. Recovery is in progress.

A load balanced WLM server has lost connectivity to all destinations in its server list. All client\n\ connections to this server will be rejected until a host in the complex becomes available again.

dbconn

"This is an informational message only. " LOG_STD_NO_ACTION

RXP_MANAGER-3-UNINIT

3-Error

[chars] [dec]

uninitialized data structure

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-NULLPTR

3-Error

[chars] 0x[hec]

null pointer

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-BADTYPE

3-Error

[chars] [dec]

illegal type

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-REFCOUNT

3-Error

bad refcnt: [chars] 0x[hec]

bad reference count

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-DEFVEC

3-Error

default vectors used: [chars]

default vector used

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-BADINDEX

3-Error

bad index value: [chars] [dec]

index value outside array limits

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-BADVAL

3-Error

unexpected value: [chars] [dec]

unexpected value encountered

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-BADBIND

3-Error

illegal bind [dec] [dec]

illegal bind operation

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

RXP_MANAGER-3-BADUNBIND

3-Error

illegal unbind [dec] [dec]

illegal bind operation

-

"Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of <CmdBold>show version<NoCmdBold> " "and <CmdBold>show running-config<NoCmdBold> and contact your Cisco technical " "support representative."

IDMNGR-3-CORECTXALLOC

3-Error

Error: Unable to handle request %08x

Unable to handle a client request

identity

"Contact support"

IDMNGR-3-INVALIDREQUEST

3-Error

Error: Invalid request type received [dec]

Unable to handle a client request

identity

"Contact support"

IDMNGR-3-INVALIDEVENT

3-Error

Error: Invalid process event received [dec]

Internal process error

identity

"Contact support"

IDMNGR-3-NOPROCESS

3-Error

Error: NO idmgr process

Internal software error

identity

"Contact support"

IDMNGR-7-ALLOCFAIL

7-Debug

Error: Failed to allocate memory for [chars]

Internal software error

identity

"Contact support"

IDMNGR-3-INVALIDARG

3-Error

Error: Argument [chars] with NIL value

Internal software error

identity

"Contact support"

IDMNGR-3-PROCNAME

3-Error

Error: Unable to get idmgr process name for request %08x

Unable to handle a client request/event

identity

"Contact support"

IDMNGR-3-EMPTYREQ

3-Error

Error: empty request received

Unable to handle a client request/event

identity

"Contact support"

IDS-4-IPOPTS_BAD_SIG

4-Warning

Sig:1000:Bad IP Option List - from [inet] to [inet]

Triggers on receipt of an IP datagram where the list of IP \n\ options in the IP datagram header is incomplete or malformed.\n\ No known exploits purposely incorporate this option.

ids

"There is no legitimate use for malformed \n\datagrams. This may be indicative of systems that are experiencing \n\problems with their kernel or NIC cards. This is unusual traffic and \n\warrants investigation. When non-specific network traffic of this \n\type is encountered the most prudent action from a security perspective \n\is to shun or disallow it. If the source of this traffic is legitimate \n\the user will then identify him or herself."

IDS-4-IPOPT_RR_SIG

4-Warning

Sig:1001:IP options-Record Packet Route - from [inet] to [inet]

The IP options list contains one or more options that\n\ perform various network management or debugging tasks.\n\ This alarm may indicate a reconnaissance attack is in\n\ progress against your network.

ids

"While network troubleshooting may require \n\the legitimate use of this feature this is unusual traffic that warrants\n\investigation. When non-specific network traffic of this type is \n\encountered the most prudent action from a security perspective is \n\to shun or disallow it. If the source of this traffic is legitimate \n\the user will then identify him or herself."

IDS-4-IPOPT_TS_SIG

4-Warning

Sig:1002:IP options-TimeStamp - from [inet] to [inet]

-

ids

"While network troubleshooting may require \n\the legitimate use of this feature this is unusual traffic that warrants\n\investigation. When non-specific network traffic of this type is \n\encountered the most prudent action from a security perspective is \n\to shun or disallow it. If the source of this traffic is legitimate \n\the user will then identify him or herself."

IDS-4-IPOPT_SECURITY_SIG

4-Warning

Sig:1003:IP options-Provide schtcc - from [inet] to [inet]

Triggers on receipt of an IP datagram where the IP option\n\ list for the datagram includes option 2. No known \n\ exploit exists.

ids

"This signature will trigger if you have \n\implemented IP security options on your network However this is \n\rarely if ever implemented . When non-specific network traffic \n\of this type is encountered the most prudent action from a security \n\perspective is to shun or disallow it. If the source of this traffic \n\is legitimate the user will then identify him or herself."

IDS-4-IPOPT_LSRR_SIG

4-Warning

Sig:1004:IP options-Loose Source Route - from [inet] to [inet]

Triggers on receipt of an IP datagram where the IP option\n\ list for the datagram includes option 3 Loose Source \n\ Route. This option may be misused to defeat

ids

"While network troubleshooting may require the \n\legitimate use of this feature this type of traffic is rarely if ever \n\noted and should comprise much less than 1% of network traffic. Small \n\amounts of source routed traffic most probably indicates that a \n\network problem is being investigated. Large amounts of source \n\routed traffic is more suspicious and a thorough investigation of the \n\source and reason is indicated."

IDS-4-IPOPT_SATID_SIG

4-Warning

Sig:1005:IP options-SATNET ID - from [inet] to [inet]

Triggers on receipt of an IP datagram where the IP\n\ option list for the datagram includes option 8 SATNET\n\ stream identifier. No known exploit exists.

ids

"This option is obsolete and should not be encountered. When\n\non-specific network traffic of this type is encountered the most \n\prudent action from a security perspective is to shun or disallow \n\it. If the source of this traffic is legitimate the user will then \n\identify him or herself."

IDS-4-IPOPT_SSRR_SIG

4-Warning

Sig:1006:IP options-Strict Source Route - from [inet] to [inet]

-

ids

"While network troubleshooting may require the legitimate use of this\n\feature this type of traffic is rarely if ever noted and should \n\comprise much less than 1% of network traffic. Small amounts of source \n\routed traffic most probably indicates that a network problem is being \n\investigated. Large amounts of source routed traffic is more suspicious \n\and a thorough investigation of the source and reason is indicated."

IDS-4-IPFRAG_ATTACK_SIG

4-Warning

Sig:1100:IP Fragment Attack - from [inet] to [inet]

Triggers when any IP datagram is received with the\n\ 'more fragments' flag set to 1 or if there is an\n\ offset indicated in the offset field.

ids

"IP datagrams may be fragmented normally as they\n\are transported across the network. This is not uncommon but is \n\unusual enough that the traffic should be investigated. This is \n\especially important if the network is protected by a packet \n\filtering firewall."

IDS-4-IP_UNKNOWN_PROTO_SIG

4-Warning

Sig:1101:Unknown IP Protocol - from [inet] to [inet]

Triggers when an IP datagram is received with the protocol\n\ field set to 101 or greater. The use of these protocol\n\ types is highly unusual and should be investigated.

ids

"Locally developed protocols that may use \n\these protocol types will trigger the signature. The use of these \n\protocol types is highly unusual and should be investigated. When \n\non-specific network traffic of this type is encountered the most \n\prudent action from a security perspective is to shun or disallow it.\n\If the source of this traffic is legitimate the user will then \n\identify him or herself."

IDS-4-IP_IMPOSSIBLE_SIG

4-Warning

Sig:1102:Impossible IP Packet - from [inet] to [inet]

This triggers when an IP packet arrives with source\n\ equal to destination address. This signature will\n\ catch the so-called Land Attack.

ids

"This should never occur in legitimate traffic."

IDS-4-ICMP_ECHO_REPLY_SIG

4-Warning

Sig:2000:ICMP Echo Reply - from [inet] to [inet]

-

ids

"This is extremely common network traffic. Suspicion should be\n\raised when a large number of these packets are found on the network. If no\n\legitimate reason for this traffic can be identified prudent security\n\practices would suggest that the source be shunned."

IDS-4-ICMP_UNREACH_SIG

4-Warning

Sig:2001:ICMP Host Unreachable - from [inet] to [inet]

-

ids

"This is the common response provided to a client when there\n\is no path available to the requested host. This is a very common type of\n\network traffic. Large numbers of this datagram type on the network are\n\indicative of network difficulties or may be indicative of hostile actions.\n\If no network problems can be identified to account for the traffic prudent\n\security practices would suggest that the source be shunned."

IDS-4-ICMP_SOURCEQUENCH_SIG

4-Warning

Sig:2002:ICMP Source Quench - from [inet] to [inet]

-

ids

"This datagram may be used in network management to provide\n\congestion control. A source quench packet will be issued when a router is\n\beginning to lose packets due to the transmission rate of a source. The\n\source quench is a request to the source to reduce the rate of datagram\n\transmission. This datagram type is rarely if ever seen on networks and some\n\systems do not even support it. Large numbers of this datagram type on the\n\network are indicative of network difficulties or may be indicative of\n\hostile actions. If no network problems can be identified to account for the\n\traffic prudent security practices would suggest that the source be shunned."

IDS-4-ICMP_REDIRECT_SIG

4-Warning

Sig:2003:ICMP Redirect - from [inet] to [inet]

-

ids

"The redirect message may be issued from a router to inform\n\a host of a better route to a requested destination. The host then updates\n\its routing table to include this route. This method of updating routing\n\tables is an uncommon practice today. When non-specific network traffic of\n\this type is encountered the most prudent action from a security\n\perspective is to shun or disallow it. If the source of this traffic is\n\legitimate the user will then identify him or herself."

IDS-4-ICMP_ECHO_SIG

4-Warning

Sig:2004:ICMP Echo Request - from [inet] to [inet]

-

ids

"The ICMP Echo Request is issued by the source to determine\n\if the destination is ''alive''. When the destination receives the request\n\it will reply with an ICMP Echo Reply. This request/reply pair is most\n\commonly implemented via the ''ping'' utility. Many network management tools\n\use this utility or some derivative. This is extremely common network\n\traffic. Suspicion should be raised when a large number of these packets are\n\found on the network. If no legitimate reason for this traffic can be\n\identified prudent security practices would suggest that the source be\n\shunned."

IDS-4-ICMP_TIMXCEED_SIG

4-Warning

Sig:2005:ICMP Time Exceeded for a Datagram - from [inet] to [inet]

Triggers when a IP datagram is received with the \n\ ''protocol'' field of the IP header set to 1 ICMP and the ''type'' \n\msgdef_recommended_actionICMP Time Exceeded datagrams are issued when a router has\n\had to drop a datagram whose Time to Live

-

-

IDS-4-ICMP_PARAMPROB_SIG

4-Warning

Sig:2006:ICMP Parameter Problem on Datagram - from [inet] to [inet]

Triggers when a IP datagram is received with the \n\ ''protocol'' field of the IP header set to 1 ICMP

ids

"ICMP Parameter Problem datagrams are issued when a router\n\has had to drop a datagram because it was malformed. This is a normal and\n\necessary type of network traffic. Large numbers of this datagram type on\n\the network are indicative of network difficulties or may be indicative of\n\hostile actions. If no network problems can be identified to account for the\n\traffic prudent security practices would suggest that the source be shunned."

IDS-4-ICMP_TIME_SIG

4-Warning

Sig:2007:ICMP Timestamp Request - from [inet] to [inet]

-

ids

"The ICMP Timestamp Request/Reply pair can be used to\n\synchronize system clocks on the network. The requesting system issues the\n\Timestamp Request bound for a destination the destination system responds\n\with a Timestamp Reply message. This is normal network traffic but is\n\uncommon on most networks. Suspicion should be raised when a large number of\n\these packets are found on the network. If no legitimate reason for this\n\traffic can be identified prudent security practices would suggest that the\n\source be shunned."

IDS-4-ICMP_TIME_REPLY_SIG

4-Warning

Sig:2008:ICMP Timestamp Reply - from [inet] to [inet]

-

ids

"The ICMP Timestamp Request/Reply pair can be used to\n\synchronize system clocks on the network. The requesting system issues the\n\Timestamp Request bound for a destination the destination system responds\n\with a Timestamp Reply message. This is normal network traffic but is\n\uncommon on most networks. Suspicion should be raised when a large number of\n\these packets are found on the network. If no legitimate reason for this\n\traffic can be identified prudent security practices would suggest that the\n\source be shunned."

IDS-4-ICMP_INFO_SIG

4-Warning

Sig:2009:ICMP Information Request - from [inet] to [inet]

-

ids

"This datagram type is obsolete and should not be\n\encountered. When non-specific network traffic of this type is encountered\n\the most prudent action from a security perspective is to shun or disallow\n\it. If the source of this traffic is legitimate the user will then identify\n\him or herself."

IDS-4-ICMP_INFO_REPLY_SIG

4-Warning

Sig:2010:ICMP Information Reply - from [inet] to [inet]

Triggers when a IP datagram is received with the \n\ ''protocol'' field of the IP header set to 1 ICMP

ids

"This datagram type is obsolete and should not be\n\encountered. When non-specific network traffic of this type is encountered\n\the most prudent action from a security perspective is to shun or disallow\n\it. If the source of this traffic is legitimate the user will then identify\n\him or herself."

IDS-4-ICMP_MASK_SIG

4-Warning

Sig:2011:ICMP Address Mask Request - from [inet] to [inet]

-

ids

"The ICMP Address Mask Request/Reply pair can be used to\n\determine the subnet mask used on the network. The requesting system issues\n\the Address Mask Request bound for a destination the destination system\n\responds with an Address Mask Reply message. This is normal network traffic\n\but is uncommon on most networks. Suspicion should be raised when a large\n\number of these packets are found on the network. If no legitimate reason\n\for this traffic can be identified prudent security practices would suggest\n\that the source be shunned."

IDS-4-ICMP_MASK_REPLY_SIG

4-Warning

Sig:2012:ICMP Address Mask Reply - from [inet] to [inet]

-

ids

"The ICMP Address Mask Request/Reply pair can be used to\n\determine the sublet mask used on the network. The requesting system issues\n\the Address Mask Request bound for a destination the destination system\n\responds with an Address Mask Reply message. This is normal network traffic\n\but is uncommon on most networks. Suspicion should be raised when a large\n\number of these packets are found on the network. If no legitimate reason\n\for this traffic can be identified prudent security practices would suggest\n\that the source be shunned."

IDS-4-ICMP_FRAGMENT_SIG

4-Warning

Sig:2150:Fragmented ICMP Traffic - from [inet] to [inet]

-

ids

"IP datagrams may be fragmented normally as they are\n\transported across the network but ICMP is rarely fragmented. The traffic\n\should be investigated. If no legitimate reason for the fragmentation can be\n\found and especially if the packets seem to be originating from a single\n\source prudent security practices would suggest that the host be shunned."

IDS-4-ICMP_TOOLARGE_SIG

4-Warning

Sig:2151:Large ICMP Traffic - from [inet] to [inet]

While it is possible to receive ICMP datagrams that have a\n\ size greater than 1024 bytes this is a highly unusual\n\ occurrence that warrants investigation.

ids

"While it is possible to receive ICMP datagrams that have a\n\size greater than 1024 bytes this is a highly unusual occurrence that\n\warrants investigation. If no legitimate reason for the large packet size\n\can be found and especially if the packets seem to be originating from a\n\single source prudent security practices would suggest that the host be\n\shunned."

IDS-4-ICMP_PING_OF_DEATH_SIG

4-Warning

Sig:2154:ICMP Ping of Death Attack - from [inet] to [inet]

-

ids

"This indicates a denial of service attack. It is likely that the source\n\address has been spoofed making shunning ineffective"

IDS-4-TCP_NO_FLAGS_SIG

4-Warning

Sig:3040:TCP - No bits set in flags - from [inet] to [inet]

Triggers when a TCP packet is received with no bits set\n\ in the flags field.

ids

"There is no legitimate use for malformed TCP datagrams. This is \n\unusual traffic and warrants investigation. Hacker tools will generate\n\TCP packets with no bits set in the flags field in an attempt to elude\n\intrusion dection. When non-specific network traffic of this\n\type is encountered the most prudent action from a security perspective\n\is to shun or disallow it. If the source of this traffic is legitimate\n\the user will then identify him or herself."

IDS-4-TCP_SYN_FIN_SIG

4-Warning

Sig:3041:TCP - SYN and FIN bits set - from [inet] to [inet]

Triggers when a TCP packet is received with both the SYN\n\ and FIN bits set in the flags field.

ids

"There is no legitimate use for malformed TCP datagrams. This is \n\unusual traffic and warrants investigation. Hacker tools will generate\n\TCP packets with the SYN and FIN bits set in the flags field in an \n\attempt to elude\n\intrusion dection. When non-specific network traffic of this\n\type is encountered the most prudent action from a security perspective\n\is to shun or disallow it. If the source of this traffic is legitimate\n\the user will then identify him or herself."

IDS-4-TCP_FIN_ONLY_SIG

4-Warning

Sig:3042:TCP - FIN bit with no ACK bit in flags - from [inet] to [inet]

Triggers when a TCP packet is received with the \n\ FIN bit set but with no ACK bit set in the flags field.

ids

"There is no legitimate use for malformed TCP datagrams. This is \n\unusual traffic and warrants investigation. Hacker tools will generate\n\TCP packets with the FIN bit set but with no ACK bit set in the flags \n\field in an attempt to elude intrusion dection. When non-specific network \n\traffic of this type is encountered the most prudent action from a \n\security perspective is to shun or disallow it. If the source of this \n\traffic is legitimate the user will then identify him or herself."

IDS-4-TCP_SYN_ATTACK_SIG

4-Warning

Sig:3050:Half-Open Syn Flood - from [inet] to [inet]

Triggers when the number of half-open TCP connections\n\ exceeds the high-water mark or the one minute high rate mark

ids

"There are no known sources that would legitimately generate\n\this traffic pattern. This may be indicative of some type of network problem\n\and should be investigated. To avoid depletion of your network resources it\n\is recommended that the source be shunned during the course of the\n\investigation. If no network problems are discovered prudent security\n\practices would suggest that the source be shunned permanently."

IDS-4-TCP_SENDMAIL_BOUNCE_SIG

4-Warning

Sig:3100:Smail Attack - from [inet] to [inet]

Triggers on the very common ''smail'' attack against e-mail\n\ servers. This attack attempts to cause e-mail servers to\n\ execute programs on the attacker's behalf.

ids

"For security reasons users should not be allowed to execute\n\programs via e-mail servers. This is a very serious indication that your\n\network may be under attack and the source should be shunned immediately. "

IDS-4-TCP_SENDMAIL_BAD_TO_SIG

4-Warning

Sig:3101:Sendmail Invalid Recipient - from [inet] to [inet]

-

ids

"For security reasons users should not be allowed to execute\n\programs via e-mail servers. This is a very serious indication that your\n\network may be under attack and the source should be shunned immediately."

IDS-4-TCP_SENDMAIL_BAD_FROM_SIG

4-Warning

Sig:3102:Sendmail Invalid Sender - from [inet] to [inet]

-

ids

"For security reasons users should not be allowed to execute\n\programs via e-mail servers. This is a very serious indication that your\n\network may be under attack and the source should be shunned immediately."

IDS-4-TCP_SENDMAIL_VRFY_SIG

4-Warning

Sig:3103:Sendmail Reconnaissance - from [inet] to [inet]

Triggers when ''expn'' or ''vrfy'' commands are issued to\n\ the SMTP port.

ids

"These commands are commonly used to verify that a user mail\n\account exists on the server or to expand an alias to determine who the\n\actual recipients of a message may be. Users that use the EXPN and VRFY\n\functions for legitimate purposes will trigger this signature. The\n\information that can be obtained is useful but not dangerous on its own.\n\Monitoring of future traffic for patterns of misuse is recommended."

IDS-4-TCP_SENDMAIL_OLD_SIG

4-Warning

Sig:3104:Archaic Sendmail Attacks - from [inet] to [inet]

Triggers when ''wiz'' or ''debug'' commands are sent to the SMTP port.

ids

"There is no reason for this type of traffic to be seen on\n\modern networks. There is little chance that there will be any adverse\n\effects from someone attempting these ''old'' hacks. Prudent security\n\practices would suggest that the source of this attempt be shunned."

IDS-4-TCP_SENDMAIL_DECODE

4-Warning

Sig:3105:Sendmail Decode Alias - from [inet] to [inet]

Triggers on any mail message with '': decode@'' in the header.\n\ The decode alias is used to uudecode files and is primarily\n\ implemented as a convenience for system administration.

ids

"The decode alias is used to uudecode files and is primarily\n\implemented as a convenience for system administration. For security\n\purposes this should not be allowed and the service should be disabled. If\n\allowed users that mail to the alias will trigger this signature. Recommend\n\shunning of hosts that attempt to mail to this alias especially if they are\n\outside of your network."

IDS-4-TCP_SENDMAIL_SPAM_SIG

4-Warning

Sig:3106:Excessive Rcpt to: SPAM - from [inet] to [inet]

Parse for RCPT TO: in header. Alarm on threshold.

ids

"Some mailing list software may trigger this signature."

IDS-4-TCP_SENDMAIL_INVALID_COMMAND

4-Warning

Invalid SMTP command - from [inet] to [inet]

Triggers on an invalid SMTP command in the \n\ SMTP connection. This message indicates that a suspicious violation \n\ was detetected that may be an attack to the mail server system.

ids

"This is unusual traffic and may warrant investigation."

IDS-4-TCP_MAJORDOMO_EXEC_BUG

4-Warning

Sig:3107:Majordomo Execute Attack - from [inet] to [inet]

A bug in the Majordomo program will allow remote users to\n\ execute arbitrary commands at the privilege level of the\n\ server.

ids

"Prudent security practices would suggest that the source of this \n\attempt be shunned."

IDS-4-TCP_FTP_SITE_SIG

4-Warning

Sig:3150:FTP Remote Command Execution - from [inet] to [inet]

Triggers when someone tries to execute the FTP SITE command.

ids

"The FTP Site command allows a user to execute a limited\n\number of commands via the FTP server on the host machine. No authentication\n\is required to execute the command. The commands that may be executed vary\n\from system to system and on many systems the SITE command is not\n\implemented. Recommend that the SITE command be disabled on FTP servers if\n\possible. If this signature is triggered from a source outside of your\n\network prudent security practices would suggest that the source be shunned."

IDS-4-TCP_FTP_SYST_SIG

4-Warning

Sig:3151:FTP SYST Command Attempt - from [inet] to [inet]

Triggers when someone tries to execute the FTP SYST command.

ids

"The FTP SYST command returns the type of operating system\n\that the FTP server is running. Authentication is not required to execute\n\this command. SYST provides information that may be used to refine attack\n\methods. FTP from Linux causes SYST signature to fire. Some proxies such as\n\the TIS Toolkit issue the SYST command as a matter of course. Running an\n\FTP version with SYST disabled."

IDS-4-TCP_FTP_CWDROOT_SIG

4-Warning

Sig:3152:FTP CWD

root - from [inet] to [inet]

Triggers when someone tries to execute the CWD

root command.

IDS-4-TCP_FTP_PORT_BADPORT_SIG

4-Warning

Sig:3154:FTP Improper Port Specified - from [inet] to [inet]

Triggers if a port command is issued with a data port specified that is \n\<1024 or >65535.

ids

"Triggers if a port command is issued with a data port specified\n\that is <1024 or >65535."

IDS-4-TCP_FTP_PORT_BADADDR_SIG

4-Warning

Sig:3153:FTP Improper Address Specified - from [inet] to [inet]

Triggers if a port command is issued with an address that is not the same \n\as the requesting host.

ids

"Triggers if a port command is issued with an address that is\n\not the same as the requesting host."

IDS-4-STR_MATCH_SIG

4-Warning

Sig:8000:FTP Retrieve Password File - from [inet] to [inet]

Triggers on string ''passwd'' issued during an FTP session.

ids

"System administrators might use this service to update\n\system files. It is a high security risk if this is normal practice and\n\should be avoided. No other benign triggers exist for this signature. If\n\after investigation the alarm was not generated by a system administrator\n\prudent security practices would suggest that the source be shunned."

IDS-4-UDP_TFTP_PASSWD_SIG

4-Warning

Sig:4100:Tftp Passwd File - from [inet] to [inet]

Triggered when someone tries to tftp a password file.

ids

"System administrators might use this service to update\n\system files. It is a high security risk if this is normal practice and\n\should be avoided. No other benign triggers exist for this signature. If\n\after investigation the alarm was not generated by a system administrator\n\prudent security practices would suggest that the source be shunned."

IDS-4-UDP_BOMB_SIG

4-Warning

Sig:4050:UDP Bomb - from [inet] to [inet]

Triggers when the UDP length specified is less than the IP\n\ length specified. This malformed packet type is associated\n\ with a denial of service attempt.

ids

"There is no legitimate use for malformed datagrams. This\n\may be indicative of systems that are experiencing problems with their\n\kernel or NIC cards. This is unusual traffic and warrants investigation.\n\When non-specific network traffic of this type is encountered the most\n\prudent action from a security perspective is to shun or disallow it. If the\n\source of this traffic is legitimate the user will then identify him or\n\herself."

IDS-4-RPC_SET_REQUEST

4-Warning

Sig:6100:RPC Port Registration - from [inet] to [inet]

Triggers when attempts are made to register new RPC services\n\ on a target host.

ids

"No benign triggers exist for this signature. Prudent\n\security practices suggest that the source of this attempt should be\n\shunned."

IDS-4-RPC_UNSET_REQUEST

4-Warning

Sig:6101:RPC Port Unregistration - from [inet] to [inet]

Triggers when attempts are made to unregister new RPC services\n\ on a target host.

ids

"No benign triggers exist for this signature. Prudent\n\security practices suggest that the source of this attempt should be\n\shunned."

IDS-4-RPC_DUMP_REQUEST

4-Warning

Sig:6102:RPC Dump - from [inet] to [inet]

Triggers when an RPC dump request isissued to a target host.

ids

"This is a common procedure performed by many system\n\administrators and wary users to determine which RPC services are being\n\offered. Executing this procedure is most likely due to curiosity on the\n\part of a novice user or a system administrator performing system\n\maintenance. If upon investigation no valid user can be associated with this\n\event prudent security practices would suggest shunning the source."

IDS-4-RPC_CALLIT_REQUEST

4-Warning

Sig:6103:Proxied RPC Request - from [inet] to [inet]

Triggers when a proxied RPC request is sent to the portmapper\n\ of a target host.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_YPSERV

4-Warning

Sig:6150:RPC ypserv Portmap Request - from [inet] to [inet]

Triggers when a request is made to the portmapper for the YP\n\ server daemon ypserv port.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_YPBIND

4-Warning

Sig:6151:RPC ypbind Portmap Request - from [inet] to [inet]

Triggers when a request is made to the portmapper for the YP\n\ bind daemon ypbind port.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_YPPASSWDD

4-Warning

Sig:6152:RPC ypbind yppasswdd Portmap Request - from [inet] to [inet]

Triggers when a request is made to the portmapper for the YP\n\ password daemon yppasswdd port.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_YPUPDATED

4-Warning

Sig:6153:RPC ypupdated Portmap Request - from [inet] to [inet]

Triggers when a request is made to the portmapper for the YP\n\ update daemon ypupdated port.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_YPXFRD

4-Warning

Sig:6154:RPC ypxfrd Portmap Request - from [inet] to [inet]

Triggers when a request is made to the portmapper for the\n\ YP transfer daemon ypxfrd port.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_MOUNTD

4-Warning

Sig:6155:RPC mountd Portmap Request - from [inet] to [inet]

Triggers when a request is made to the portmapper for the\n\ mount daemon mountd port.

ids

"If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned."

IDS-4-RPC_PORTREQ_REXD

4-Warning

Sig:6175: RPC rexd Portmap Request - from [inet] to [inet]

-

ids

"If this procedure is allowed on your network those users\n\who employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network it should be shunned."

IDS-4-RPC_REXD_REQUEST

4-Warning

Sig:6180:RPC rexd Attempt - from [inet] to [inet]

Triggers when a call to the rexd program is made. The remote execution \n\daemon is the server responsible for remote program execution. This\n\may be indicative of an attempt to gain unauthorized access to system \n\resources.

ids

"If this service is being used legitimately this alarm will\n\fire. For security purposes this service really should not be used."

IDS-4-RPC_STATD_OVFLW

4-Warning

Sig:6190:statd Buffer Overflow - from [inet] to [inet]

Triggers when a large statd request is sent.

ids

"You should not see this in legitimate traffic."

IDS-4-LOST_CONNECT

4-Warning

Connection to HostID:[dec] OrgID:[dec]

Triggers when a connection drops and there is no previous \n\connection.

ids

"This message indicates that the IDS cannot communicate with the \n\Director. Check connectivity to the Director and check Postoffice\n\configuration on both the router and the Director."

IEDGE-4-PBHK_DEPLETED_INDICES

4-Warning

No more portbundles can be allocated

The source interfaces configured for Portbundle Hostkey feature are not sufficient and the number of portbundles available are all used up. Add more source interfaces in the configuration.

sss

"Check configuration on the ISG"

IEDGE-4-TC_UNDEFINED_ACL

4-Warning

Traffic class ACL [chars] is not defined creating permit all ACL

The ACL specified for classification of traffic is not configured on the ISG. Creating a permit all ACL. ACL should be configured on the ISG.

sss

"Configure the ACL on the ISG"

IEDGE-4-CLOCK_CHANGE_TIMER_INV

4-Warning

A Local clock change has caused a running timer to be invalid

A change in local clock has made a currently running timer to be invalid

sss

"Check the clock configuration"

IEDGE-3-CH_INTERNAL_ERROR

3-Error

Internal error in command processing - session handle=[hex]

There has been an internal error relating to CoA command processing.

policy

"Copy the error message exactly as it appears and " "report it to your technical support " "representative."

IEDGE-3-CH_REGISTER_ERROR

3-Error

CoA registration error in command processing - type '[chars]'

There has been an internal error relating to CoA command processing.

policy

"Copy the error message exactly as it appears and " "report it to your technical support " "representative."

LINK-4-NOMAC

4-Warning

A random default MAC address of [enet] has\n been chosen. Ensure that this address is unique or specify MAC\n addresses for commands such as 'novell routing' that allow the\n

An addressing inconsistency occurred.

-

"Make sure that this address is unique or specify MAC addresses for\n\ commands such as novell routing that allow the use of this address as a\n\ default."

LINK-4-NOSSB

4-Warning

SSB deleted with timer running

An internal software error occurred.\n Problem has been corrected and router operation\n has not been impaired.

-

LOG_STD_ACTION

LINK-2-NOSOURCE

2-Critical

Source idb not set

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

LINK-2-LINEST

2-Critical

No linestate vector for [chars]

An internal software inconsistency occurred.

-

LOG_STD_ACTION

LINK-5-CHANGED

5-Notice

Interface [chars] changed state to [chars]

The interface hardware changed state.

-

LOG_STD_ACTION

LINK-3-UPDOWN

3-Error

Interface [chars] changed state to [chars]

The interface hardware went either up or down.

-

"If the state change was unexpected confirm the configuration settings\n\ for the interface."

LINK-4-TOOBIG

4-Warning

Interface [chars] Output packet size of [dec] bytes too big

An internal software error occurred.

-

LOG_STD_ACTION

LINK-3-TOOSMALL

3-Error

Interface [chars] Output runt packet of [dec] bytes

An output packet was detected that was smaller than the minimum\n\ allowable datagram size. An error in another driver or an error in \n\ the system software probably triggered this error message.

-

LOG_STD_ACTION

LINK-3-BADMACREG

3-Error

Interface [chars] non-existent MACADDR registry for link [dec]

An attempt to map a network level address to a MAC level address\n\ failed.

-

LOG_STD_ACTION

LINK-3-BADENCAP

3-Error

Interface [chars] Bad encapsulation code [dec]

-

-

-

LINK-2-BADVCALL

2-Critical

Interface [chars] undefined entry point

An internal software error occurred. The high-level system code tried\n\ to use an unimplemented entry point with the virtual interface\n\ descriptor block IDB driver.

-

LOG_STD_ACTION

LINK-2-INTVULN

2-Critical

MSG_PROCESS | MSG_TRACEBACK

-

-

-

LINK-0-REENTER

0-Emergency

MSG_PROCESS | MSG_TRACEBACK

-

-

-

LINK-5-BOOTP

5-Notice

[chars] address [inet] resolved by [inet]

An interface's IP address was successfully learned dynamically through\n\ BootP. The first address is the learned IP address. The second IP\n\ address is the IP address of the BootP server that provided the\n\ information.

-

LOG_STD_ACTION

LINK-5-RARP

5-Notice

[chars] address [inet] resolved by [inet]

-

-

LOG_STD_ACTION

LINK-5-SLARP

5-Notice

[chars] address [inet] resolved by [inet]

-

-

LOG_STD_ACTION

LINK-4-FDDISTAT

4-Warning

Interface [chars] FDDI state [chars] detected

There was a state change on the FDDI ring.

-

LOG_STD_ACTION

LINK-4-BRIDGECONFLICT

4-Warning

Interface [chars] encapsulated BPDU recvd from [enet]

An FCIT running in nonencapsulating transparent mode detected an FDDI\n\ bridge running in encapsulation mode on the same fiber. This is an\n\ unstable situation and should be corrected. The incoming interface is\n\ displayed along with the FDDI MAC address in standard form.

-

"Upgrade the errant interface to full transparent mode. Copy the error\n\ message exactly as it appears and report it to your Cisco\n\ technical support representative."

LINK-5-REMLOOP

5-Notice

Interface [chars] remote loop [chars] [chars]

The interface entered or exited a remote loopback.

-

LOG_STD_ACTION

LINK-5-LOOPSTATUS

5-Notice

Interface [chars] [chars]

The interface entered or exited loopback.

-

LOG_STD_ACTION

LINK-6-BERTSTATUS

6-Information

Interface [chars] [chars]

BERT is completed for this interface.

-

LOG_STD_ACTION

LINK-6-BERTMSGS

6-Information

[chars]

BERT related information messages.

-

LOG_STD_ACTION

LINK-3-COMPREG

3-Error

Interface [chars] non-existent decompression registry.

A software or hardware error occurred.

-

LOG_STD_ACTION

LINK-3-BOGUSENCAP

3-Error

msgtxt_badencap

A serial interface has been configured with an unknown\n\ encapsulation.

-

LOG_STD_ACTION

LINK-4-BADQID

4-Warning

Interface [chars] bad output queue ID specified [dec].

This message indicates an internal software error.

-

LOG_STD_ACTION

LINK-3-IDBLISINS

3-Error

Not able to insert interface [chars] into [chars] list

This message indicates an internal software error.

-

LOG_STD_ACTION

LINK-3-IDBLISCRE

3-Error

Unable to create [chars] interface list

This message indicates an internal software error.

-

LOG_STD_ACTION

LINK-3-LINK_FAULT

3-Error

[chars] [chars] [chars] [chars]

The link state for the port is down

-

LOG_STD_ACTION

LINK-3-FCS_ERROR

3-Error

[chars] [chars] [chars] [chars]

The FCS Error rate exceeds the configured threshold

-

LOG_STD_ACTION

GBIC_SECURITY_UNIQUE-4-DUPLICATE_SN

4-Warning

GBIC interface [dec]/[dec] has the same serial number as another GBIC interface

The GBIC was identified as a Cisco GBIC but its serial number matches that of another interface on the system.

firmware

"Cisco GBICs are assigned unique serial numbers. Verify that the GBIC " "was obtained from Cisco or a supported vendor"

GBIC_SECURITY_UNIQUE-3-DUPLICATE_GBIC

3-Error

GBIC interface [dec]/[dec] is a duplicate of GBIC interface [dec]/[dec]

The GBIC was identified as a Cisco GBIC but its vendor ID and serial number match that of another interface on the system.

firmware

"Cisco GBICs are assigned unique serial numbers. Verify that the GBIC " "was obtained from Cisco or a supported vendor"

SFF8472_FLOAT-3-INTERNAL_ERROR

3-Error

[chars]

The SFF8472 floating point subsystem encountered an internal\n\ software error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

FEC_ISSU-3- INIT

3-Error

FEC ISSU client initialization failed at [chars] error [chars]

FEC ISSU client could not be initiailzed this will cause catstrophic failure when ISSU upgrade or downgrade is performed.

L2

LOG_STD_SH_TECH_ACTION

FEC_ISSU-3- TRANSFORM

3-Error

FEC ISSU client [chars] transform failed error [chars]

FEC ISSU client could not transform the message. If the transmit transformation failed it means that the checkpoint message can not be sent to the standby unit. If the receive transformation failed it means that the checkpoint message can not be applied on the standby unit. In both cases the FEC state will not be indentical with the active unit.

L2

"show issu session <client_id> and " "show issu negotiated version <session_id>"

FEC_ISSU-3- MSG_NOT_OK

3-Error

FEC ISSU client message [dec] is not compatible

FEC ISSU client received an incompatible message from the peer unit. Since the message is not compatible it can be processed by this unit

L2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

FEC_ISSU-3- MSG_SIZE

3-Error

FEC ISSU client failed to get the message size for message [dec]

FEC ISSU client failed to calculate message size for the message specified. The OIR ISSU client will not be able to send message to the standby unit.

L2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

FEC_ISSU-3-SESSION

3-Error

FEC ISSU client [chars]

FEC ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

FEC_ISSU-3- SESSION_UNREGISTRY

3-Error

FEC ISSU client failed to unregister session information. Error: [dec] [chars]

The FEC ISSU client failed to unregister session information.

L2

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

FEC_ISSU-3- SEND_FAILED

3-Error

FEC ISSU client failed to send a negotiation message error [dec]

FEC ISSU client could not send a session negotiation message to the peer. When there is a problem in the negotiation the standby unit can not be brought up.

L2

"show logging and show checkpoint client"

FEC_ISSU-3- BUFFER

3-Error

FEC ISSU client failed to get buffer for message error [dec]

FEC ISSU client failed to get buffer for building a negotiation message. Hence it can send the negotiation message to the standby unit. When there is a problem in the negotiaiton the standby unit can not be brought up.

L2

"show logging and show checkpoint client"

FEC_ISSU-3- CAPABILITY

3-Error

FEC ISSU client [chars]

FEC SWITCH ISSU client observed an error during capability negotiaiton. When this error happens there is a mismatch between the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

FEC_ISSU-3- POLICY

3-Error

FEC ISSU client message type [dec] is [chars]

FEC ISSU client received an message type which it does not support. The policy is applied to make the session compatible.

L2

"show issu session <client_id>"

TEMPLATE-3-TEMPLATE_FAIL

3-Error

[chars] template [chars] binding to [chars] failed due to [chars] CLI failure.

Template binding failed due to failure status returned by binding.

-

-

VDSL_DAEMON-3-NOPROC

3-Error

VDSL Daemon [chars] SM create event process failed

The router does not have enough memory run this VDSL/ADSL feature

-

LOG_STD_ACTION

VDSL_DAEMON-3-NOMEM

3-Error

VDSL Daemon [chars] malloc failed : out of memory

The router does not have enough memory installed to run this \n\VDSL/ADSL feature

-

LOG_STD_ACTION

VDSL_DAEMON-3-MALLOCFAIL

3-Error

There is not enough main memory for the new VDSL [chars] firmware images on flash

The router failed to malloc a buffer for the firmware images\n\on the flash. More DRAM is required for the feature which allows specific\n\VDSL firmware images on the flash to replace the VDSL firmware images\n\embedded in IOS.

-

LOG_STD_ACTION

VDSL_DAEMON-3-INITFAIL

3-Error

VDSL Daemon [chars] init failed.

The VDSL module hardware may be bad

-

LOG_STD_ACTION

VDSL_DAEMON-3-INVALID_DS

3-Error

Daemon [chars] invalid vdsl instance.

Encounter an invalid vdsl instance

-

LOG_STD_ACTION

VDSL_DAEMON-4-QUEUE_EMPTY

4-Warning

Daemon [chars] configuration queue is empty.

program is unable to send a message to the queue process.

-

"nothing"

VDSL_DAEMON-4-INVALID_CDB

4-Warning

Invalid daemon [chars] controller [chars].

Encounter an invalid daemon cdb instance.

-

"nothing"

VDSL_DAEMON-3-FPGA_FAIL

3-Error

VDSL FPGA Download failed.

The VDSL module hardware may be bad

-

LOG_STD_ACTION

VDSL_DAEMON-3-MODEMRESET

3-Error

VDSL Modem reset. [chars]

The VDSL module is under reset.

-

LOG_STD_RECUR_ACTION

VDSL_DAEMON-4-TRAINMODE_NOT_SUPPORTED

4-Warning

[chars] transport mode is not supported on [chars].

Only ATM is supported on ADSL and PTM/Ethernet is supported on VDSL2.

-

"Change DSLAM profile to select the correct mode for CPE"

VDSL_DAEMON-3-VDSL_CMD_ADD_FAIL

3-Error

VDSL [chars] add failed.

adding a command exceeds the maximum number of commands allowed

-

LOG_STD_ACTION

VDSL_DAEMON-3-FIRMWARE_WARN

3-Error

Need to reload IOS for VDSL PHY firmware file change to take effect

The old phy firmware is used until IOS is reload

-

LOG_STD_ACTION

VDSL_DAEMON-4-MODE_SWITCH

4-Warning

Please save the configuration and reload the Router due to the ATM-PTM mode change on vdsl 0 controller

Operating mode switch between ATM and PTM mode require reload

-

"LOG_STD_ACTION"

VDSL_DAEMON-3-VDSL_LINE_UPDOWN

3-Error

Controller [chars] line [dec] changed state to [chars]

VDSL Line changed state

-

LOG_STD_ACTION

TR-2-PANICTYPE

2-Critical

Unit [dec] [chars] error

This message is similar to the %TR-3-PANIC error message but\n\ indicates a nonfatal error. This message appears in very unusual\n\ situations that should not arise in normal operation.

-

LOG_STD_SH_TECH_ACTION

TR-2-PANIC

2-Critical

Unit [dec] panic %-08x %-08x %-08x

The Token Ring monitor firmware detected a fatal error that indicates\n\ an impending interface failure.

-

LOG_STD_ACTION_CRIT

TR-2-PANICINF

2-Critical

Unit [dec] PI %-08x %-08x %-08x %-08x %-08x %-08x

This message is similar to the %TR-3-PANIC error message but\n\ indicates a nonfatal error. This message appears in very unusual\n\ situations that should not arise in normal operation.

-

LOG_STD_SH_TECH_ACTION

TR-3-BADMUL

3-Error

[chars]: Can't set address to a multicast [enet]

An attempt was made to set the Token Ring interface MAC address to a\n\ reserved multicast address.

-

"Check your configuration. Make sure that your XNS and/or Novell Token\n\ Ring addresses have not inadvertently been set to reserved multicast\n\ addresses."

TR-3-BADSTART

3-Error

Unit [dec] Start completion and wrong idb state - state= [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-3-RESETFAIL

3-Error

Unit [dec] reset failed error code %-08x.

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-6-STATE

6-Information

[chars]: Ring Status: [chars]

This message is displayed when the Token Ring's status changed as\n\ determined by the chipset. This information also is used to\n\ automatically determine whether the interface is still usable to\n\ propagate network traffic.

-

LOG_STD_NO_ACTION

TR-6-STATRING

6-Information

TR[dec]: Ring Status: [chars] [chars]

This message is displayed when the Token Ring's status changed as\n\ determined by the chipset. This information also is used to\n\ automatically determine whether the interface is still usable to\n\ propagate network traffic. The meaning of each status code is shown in\n\ the \Token Ring Status Codes\ Table.\n\\n\ Code Explanation Fatal\n\ 0x8000 Signal loss Yes\n\ 0x4000 Hard error Yes\n\ 0x2000 Soft error No\n\ 0x1000 Transmit beacon Yes\n\ 0x0800 Lobe wire fault Yes\n\ 0x0400 Auto removal error Yes\n\ 0x0100 Receive request removed Yes\n\ 0x0080 Counter overflow No\n\ 0x0040 Single station No\n\ 0x0020 Ring recovery No\n\

-

"Check the Token Ring for the indicated condition."

TR-3-INTFAIL

3-Error

Unit [dec] interface failure: [hex] [hex] [hex] idb state [dec]

The Token Ring Monitor firmware detected a fatal error due either to\n\ an internal software problem or to a hardware failure.

-

LOG_STD_SH_TECH_ACTION

TR-3-BADRNGNUM

3-Error

Unit [dec] ring number [dec] doesn't match established number [dec].

The number you have configured for the local ring does not match the\n\ value currently in use on the ring.

-

"Check the configuration to make sure you used the correct ring number.\n\ If it is correct confirm the configuration of all other bridges on the\n\ ring to make sure they are using the same ring number."

TR-3-WIREFAULT

3-Error

Unit [dec] wire fault: check the lobe cable MAU connection.

The Token Ring hardware is reporting a wire fault condition.

-

"Check the cable connecting the router to the Token Ring media\n\ attachment unit MAU."

TR-3-OPENFAIL

3-Error

Unit [dec] open failed: [chars] [chars]

The Token Ring interface was unable to insert itself into the ring.\n\ This is an indication of a busy or broken ring. The first character\n\ string in this error message indicates the stage of initialization at\n\ which the error occurred and the second describes the error.

-

"Try to open the interface again. This generally can be accomplished by\n\ issuing the clear interface tokenring command. If the error message\n\ recurs call your Cisco technical support representative for\n\ assistance."

TR-3-OPENFAIL2

3-Error

Unit [dec] open failed: check the lobe cable DB-9 connection.

The Token Ring interface was unable to insert itself into the ring\n\ and the error code returned indicates a wiring problem.

-

"Check the cable connecting the router to the Token Ring MAU and try\n\ to open the interface again. This generally can be accomplished by\n\ issuing the clear interface tokenring command. " LOG_STD_RECUR_ACTION

TR-3-SETGRPFAIL

3-Error

Unit [dec] set group address failed code [hex].

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-3-SETFUNFAIL

3-Error

Unit [dec] set functional address failed code [hex].

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-3-SETBRIDGEFAIL

3-Error

Unit [dec] set bridge failed code [hex].

-

-

LOG_STD_SH_TECH_ACTION

TR-3-BADUNIT

3-Error

Bad unit number [dec]

This error message pertains only to the IGS. When displayed it\n\ indicates that the system cannot find the chipset registers where it\n\ expects them to be. This is most likely a hardware error.

-

"If this message recurs call your technical support representative for\n\ assistance. It will be necessary to determine the hardware unit\n\ configuration."

TR-3-BADBUFFSIZE

3-Error

Unit [dec] bad buffersize = [dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-3-BADFUNC

3-Error

Unit [dec] bad functional address=0x%08x ring mode=0x%08x

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-3-BADBRDGPARMS

3-Error

Unit [dec] bad bridge parameters: bridge_num=[dec] max_rd=[dec]\nthisring=[dec] targetring=[dec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

TR-3-INITFAIL

3-Error

Unit [dec] init failed. result code=[hex] error code=[hex]

The Token Ring hardware failed to initialize properly.

-

LOG_STD_SH_TECH_ACTION

TR-3-MODEFAIL

3-Error

Unit [dec] change mode failed. result code=[hex] error code=[hex]

An internal hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

TR-3-NOFIRM

3-Error

Unit [dec] no TMS380 firmware present. eagle=[hex] magic=[hex]

An internal hardware or software error occurred.

-

LOG_STD_SH_TECH_ACTION

TR-3-BADFIRMTYPE

3-Error

Unit [dec] bad firmware type code during [chars]. type=[hex] fw=[hex]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

TR-3-BADFIRM

3-Error

Unit [dec] Tokenring firmware download failed\n got [hex] expected [hex] at address 0x%04x.%04x

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

TR-2-NOMEMORY

2-Critical

Unit [dec] no memory for [chars]

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

TR-3-DIAGFAIL

3-Error

Interface [chars] failed init diags 0x%04x [chars]

The microcode attempted to run its diagnostics on the chip and\n\ failed.

-

"Issue a clear interface command. " LOG_STD_RECUR_ACTION

TR-3-ADPCHK

3-Error

Interface [chars] adapter check error non-fatal%04x %04x %04x %04x

The Token Ring monitor firmware detected a non-fatal error on the\n\ interface card.

-

"Issue a clear interface command. If this message recurs call your\n\ technical support representative for assistance."

TR-3-ADPCHKFATAL

3-Error

Interface [chars] adapter check error fatal %04x %04x %04x %04x

The Token Ring monitor firmware detected a fatal error on the\n\ interface card.

-

"Issue a clear interface command. If this message recurs call your\n\ technical support representative for assistance. You may need to \n\ replace the interface card "

LB-3-ECHAN_CMDREP_REG_FAILURE

3-Error

Failed to register bundle interface [chars] for Command Replay service

For the given link bundle interface failed to register it for the Command Replay service.

gsr-link-bundling

LOG_STD_ACTION

LB-3-ECHAN_FCB_ERROR

3-Error

Bundle creation feature callback failed for [chars]

For the given link bundle interface failed to create its feature callback.

gsr-link-bundling

LOG_STD_ACTION

LB-3-ECHAN_ADDR_ALLOC_ERROR

3-Error

Channel [dec] error in MAC address allocation configured MAC address [enet] actual MAC address [dec]

For the given channel number addition of the first member caused a failure in changing the MAC address of the channel to that of this first member.

gsr-link-bundling

LOG_STD_ACTION

LB-3-POSCHAN_CMDREP_REG_FAILURE

3-Error

Failed to register bundle interface [chars] for Command Replay service

For the given link bundle interface failed to register it for the Command Replay service.

gsr-link-bundling

LOG_STD_ACTION

LB-3-POSCHAN_FCB_ERROR

3-Error

Bundle creation feature callback failed for [chars]

For the given link bundle interface failed to create its feature callback.

gsr-link-bundling

LOG_STD_ACTION

LB-5-CHAN_MEMBER_IN

5-Notice

[chars] added as member-[dec] to [chars]channel[dec]

The given channel member interface was added to the given channel number.

gsr-link-bundling

LOG_STD_NO_ACTION

LB-5-CHAN_MEMBER_OUT

5-Notice

[chars] taken out of [chars]channel[dec]

The given channel member interface was taken out of the given channel number.

gsr-link-bundling

LOG_STD_NO_ACTION

LB-5-CHAN_MEMBER_ADD_PASSIVE

5-Notice

[chars] added as passive member to [chars]channel[dec]

The given interface was added as a passive member in the given channel number.

gsr-link-bundling

LOG_STD_NO_ACTION

LB-5-CHAN_MEMBER_MOVED_PASSIVE

5-Notice

[chars] moved to passive state in [chars]channel[dec]

The given channel member interface became a passive member in the given channel number.

gsr-link-bundling

LOG_STD_NO_ACTION

LB-5-CHAN_MEMBER_MOVED_ACTIVE

5-Notice

[chars] moved to active state as member-[dec] in [chars]channel[dec]

The given etherchannel member interface became an active member in the given channel number.

gsr-link-bundling

LOG_STD_NO_ACTION

LB-3-FUNCTION_VECTOR_EMPTY

3-Error

Empty link bundling function vectors

One or more function vectors used in generic etherchannel and poschannel code was null i.e. not initialized. This is a severe error resulting from a coding error. Crash will happen because this error prevents the proper functioning of the ether or pos channel features.

gsr-link-bundling

LOG_STD_ACTION

LB-3-CHUNK_CREATE_FAIL

3-Error

[chars]channel: failed to create chunk

An internal data structure called a chunk and used for channel route processor - line card interprocess communications failed to be created. Such interprocss communication may be impeded.

gsr-link-bundling

LOG_STD_ACTION

LB-3-FEATURE_ACL_APPLY_ERROR

3-Error

Failed to apply ACL [dec] to interface [chars]. Removing new ACL config reapplying old ACL [dec].

For the given member interface or subinterface failed to apply the given ACL. This new ACL configuration is removed from the bundle and the old ACL configuration if any is reapplied to the bundle. The new ACL that failed to be applied is removed in order to maintain consistent state for the whole bundle.

gsr-link-bundling

LOG_STD_ACTION

LB-3-ACL_FCB_REG_ERROR

3-Error

Failed to registered Link Bundle ACL feature control block

For the given interface failed to register the ACL feature control block.

gsr-link-bundling

LOG_STD_ACTION

LB-3-FEATURE_ACL_REG_ERROR

3-Error

Failed to register ACL control block with Link Bundle subinterface module

For the given interface failed to register the ACL feature control block. This happened during install ACL support for link bundling. ACL support installation for link bundling is aborted.

gsr-link-bundling

LOG_STD_ACTION

LB-3-FEATURE_REG_ERROR

3-Error

One or more NULL feature callbacks in the passed in Feature Control Block

In registering a feature for services from link bundling feature support there were one or more NULL function pointers used as function callbacks. Aborted the feature registration as a result.

gsr-link-bundling

LOG_STD_ACTION

LB-3-FEATURE_MODULE_INIT_ERROR

3-Error

Failed to create Link Bundle Feature ListQ

In initializing link bundling feature support an internal list queue failed to be created.

gsr-link-bundling

LOG_STD_ACTION

LB-3-FEATURE_INSTALL_ERROR

3-Error

One or more NULL feature control block members

In installing link bundling feature support there were one or more NULL function pointers used in a feature control block. Installation of the feature support is aborted.

gsr-link-bundling

LOG_STD_ACTION

LB-3-SUBINT_ERROR

3-Error

[chars] [chars]

There was a subinterfce error for the given interface.

gsr-link-bundling

LOG_STD_ACTION

LB-3-SUBINT_NOTIF_INIT_FAILURE

3-Error

Failed to create Link Bundle Subinterface ClientQ

In initializing link bundling subinterface feature support an internal subinterface client queue failed to be created.

gsr-link-bundling

"Copy the error message exactly as it appears and report it to your technical support representative."

LB-3-SUBINT_NOTIF_REG_FAILURE

3-Error

NULL notification callback

In registering a client for service from the Link Bundling subinterface module the callback notification callback function was NULL.

gsr-link-bundling

LOG_STD_ACTION

LB-3-SUBINT_INSTALL_SUPPORT_FAILURE

3-Error

Failed to registered Link Bundle subinterface control block

In initializing link bundling subinterface feature support could not register for notifications from the common link bundle infrastructure.

gsr-link-bundling

LOG_STD_ACTION

SHDSL-3-NOMEM

3-Error

SHDSL [chars] malloc failed : out of memory

The router does not have enough memory installed to run this SHDSL feature

-

LOG_STD_ACTION

SHDSL-1-INIT

1-Alert

SHDSL[dec]/[dec]/[dec]: [chars].

An attempt to initialize the SHDSL NIM failed. This module cannot be used

-

LOG_STD_ACTION

SHDSL-1-FWDNLD

1-Alert

[chars] [chars].

An attempt to download firmware for SHDSL card failed. This interface cannot be used.

-

LOG_STD_ACTION

SHDSL-1-TCLAYER

1-Alert

SHDSL[dec]/[dec]/[dec]: [chars] [dec].

if CPE-CO modeATM/EFM configuration is improper

-

"Change the modeATM to EFM or EFM to ATMconfiguration"

SHDSL-1-INFO

1-Alert

SHDSL[dec]/[dec]/[dec]: [chars].

Info on SHDSL card.

-

LOG_STD_ACTION

SHDSL-4-ERRORINT

4-Warning

Error interrupt: [chars] received

A spurious event happened for the SHDSL card.

-

LOG_STD_ACTION

SHDSL-6-DSLGROUP_UPDOWN

6-Information

[chars] dsl-group [dec] state changed to [chars].

DSL Group state is changed.

-

LOG_STD_NO_ACTION

SHDSL-6-EFM_BOND_LINK_RATE_CHANGE

6-Information

[chars] EFM Link[dec] bandwidth is changed.

SHDSL link is trained to a different rate EFM bonding group.

-

LOG_STD_NO_ACTION

SHDSL-6-EFM_ACT_LINK_CHANGE

6-Information

[chars] EFM Group [dec] has [dec] active links active link bitmap is [hex].

Active Links were added or removed from the Group changing its bandwidth.

-

LOG_STD_NO_ACTION

SHDSL-5-DYING_GASP

5-Notice

Power failure at CPE detected at link no [dec].

CPE has gone down because of power failure.

-

LOG_STD_NO_ACTION

SHDSL-3-EFM_FRAME_SIZE

3-Error

[chars] [chars].

An attempt to change the maximum frame size in EFM bonding scenario has failed.

-

LOG_STD_ACTION

SHDSL-1-EFM_BOND

1-Alert

[chars] CPE-CO configuration mismatch detected for link:[dec].

If CPE is configured in efm bonding and CO is configured in plain 2wire then link will come-up in plain 2-wire. Since CPE is configured in efm bonding CPE will ignore link up event

-

"Correct either CPE or CO's configuration"

SHDSL-3-FIRMWARE

3-Error

[chars] [chars]

Error occured in the SHDSL module firmware.

-

LOG_STD_ACTION

SHDSL-6-PHY_FWDNLD

6-Information

[chars] [chars] [chars]

Info about status of SHDSL Phy firmware download.

-

LOG_STD_NO_ACTION

SHDSL-3-PHY_FWDNLD_FAIL

3-Error

[chars] [chars] could be incomplete or corrupted or not present in [chars]

Error occured in the SHDSL Phy firmware download.

-

"Use correct firmware package file"

SHDSL-1-NGIO_DROP

1-Alert

Command dropped since phy re-init is in progress.

If ngio_drop_messages is set then the messages are dropped in host

-

"Wait till the phy reinit is complete"

QOS_CLI_DEPRECATE-4-TRAFFIC_SHAPE

4-Warning

Traffic shape on interface has been deprecated. Use equivalent MQC traffic-shape command

The issued interface traffic shape command has been deprecated by the MQC commands.\n

-

"Configure a policy with traffic-shape and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-RANDOM_DETECT

4-Warning

Random detect on interface has been deprecated. Use equivalent MQC random-detect command

The issued interface random detect command has been deprecated by the MQC commands.\n

-

-

QOS_CLI_DEPRECATE-4-FAIR_QUEUE

4-Warning

Fair Queue on interface has been deprecated. Use equivalent MQC fair-queue command

The issued interface fair queue command has been deprecated by the MQC commands.\n

-

"Configure a policy with fair-queue and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-CUSTOM_QUEUE

4-Warning

Custom Queue list on interface has been deprecated. Use equivalent MQC bandwidth command

The issued interface custom queue list command has been deprecated by the MQC commands.\n

-

"Configure a policy with bandwidth and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-PRIORITY_QUEUE

4-Warning

Priority Queue on interface has been deprecated. Use equivalent MQC priority command

The issued interface priority-group command has been deprecated by the MQC commands.\n

-

"Configure a policy with priority and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-PRIORITY_LIST

4-Warning

priority-list global config mode CLI has been deprecated. Use equivalent MQC priority command. For further information please consult Product Bulletin 580832 Legacy QoS CLI Commands Deprecation

The issued global config mode priority-list command has been deprecated by the MQC commands.\n

-

-

QOS_CLI_DEPRECATE-4-QUEUE_LIST

4-Warning

queue-list global config mode CLI has been deprecated. Use equivalent MQC priority command. For further information please consult Product Bulletin 580832 Legacy QoS CLI Commands Deprecation

The issued global config mode queue-list command has been deprecated by the MQC commands.\n

-

-

QOS_CLI_DEPRECATE-4-MAX_RESERVED_BW

4-Warning

max-reserved-bandwidth on interface has been deprecated

The issued max-reserved-bandwidth command has been deprecated by the MQC bandwidth command.\n

-

"Configure a policy with bandwidth and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-FR_IP_RTP_PRIO

4-Warning

frame relay ip rtp priority has been deprecated. Use equivalent MQC priority command

The issued frame-relay interface ip rtp priority command has been deprecated by the MQC commands.\n

-

"Configure a policy with priority and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-FR_ADAPTIVE_SHAPE

4-Warning

frame relay adaptive-shaping has been deprecated. Use equivalent MQC priority command

The issued interface shape command has been deprecated by the MQC commands.\n

-

"Configure a policy with shape and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-FRVCQ_CUSTOM

4-Warning

frame relay custom-queue-list command has been deprecated. Use equivalent MQC bandwidth command

The issued frame-relay custome-queue command has been deprecated by the MQC commands.\n

-

"Configure a policy with bandwidth and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-FRVCQ_FAIR

4-Warning

frame relay fair-queue command has been deprecated. Use equivalent MQC fair-queue command

The issued frame-relay fair-queue command has been deprecated by the MQC commands.\n

-

"Configure a policy with fair-queue and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-FRVCQ_PRIORITY

4-Warning

frame relay priority-group command has been deprecated. Use equivalent MQC priority command

The issued frame-relay priority-group command has been deprecated by the MQC commands.\n

-

"Configure a policy with priority and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-FRFECN_ADAPT

4-Warning

frame relay fecn-adapt command has been deprecated. Use equivalent MQC priority command

The issued frame-relay fecn-adapt command has been deprecated by the MQC commands.\n

-

"Configure a policy with MQC and attach to the interface\n"

QOS_CLI_DEPRECATE-4-FR_THRESH_ECN

4-Warning

frame relay congestion threshold ecn command has been deprecated. Use equivalent MQC priority command

The issued frame-relay congestion threshold ecn has been deprecated by the MQC commands.\n

-

"Configure a policy with MQC and attach to the interface\n"

QOS_CLI_DEPRECATE-4-FR_THRESH_DE

4-Warning

frame relay congestion threshold de command has been deprecated. Use equivalent MQC priority command

The issued frame-relay congestion threshold de has been deprecated by the MQC commands.\n

-

"Configure a policy with MQC and attach to the interface\n"

QOS_CLI_DEPRECATE-4-IP_RTP_PRIO

4-Warning

ip rtp priority command on interface has been deprecated. Use equivalent MQC priority command

The issued interface ip rtp priority command has been deprecated by the MQC commands.\n

-

"Configure a policy with priority and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-IP_RTP_RESV

4-Warning

ip rtp reserve command on interface has been deprecated. Use equivalent MQC reserve command. For further information please consult Product Bulletin 580832 Legacy QoS CLI Commands Deprecation

The issued interface ip rtp reserve command has been deprecated by the MQC commands.\n

-

"Configure a policy with reserve and attach to " "the interface\n"

QOS_CLI_DEPRECATE-4-RANDOM_DETECT_GROUP

4-Warning

Random detect group command has been deprecated

The issued random detect group command has been deprecated by the MQC commands.\n

-

-

QOS_CLI_DEPRECATE-4-FR_CBS

4-Warning

Frame relay bc command has been deprecated. Use equivalent MQC priority command

The issued frame-relay bc command has been deprecated by the MQC commands.\n

-

-

QOS_CLI_DEPRECATE-4-FR_EBS

4-Warning

Frame relay be command has been deprecated. Use equivalent MQC priority command

The issued frame-relay be command has been deprecated by the MQC commands.\n

-

-

QOS_CLI_DEPRECATE-4-FR_CIR

4-Warning

Frame relay cir command has been deprecated. Use equivalent MQC priority command

The issued frame-relay cir command has been deprecated by the MQC commands.\n

-

-

ETHERCHANNEL_LB-3-MSG_SEND_FAIL

3-Error

The load-balance message [dec] has failed to send

The load-balancing feature has detected an error while trying to send an internal message.

ether-channel

"If this message was the result of performing a " "configuration command then try unconfiguring " "and reconfiguring the same command. If the error " "message continues to be displayed then it may " "indicate that the system is low on memory. The " "show memory free command should be used to check " "if the system has sufficient available memory. " "If the system appears to have available memory and " "the error continues to be displayed then please " "contact your Cisco technical support representative " "and provide the representative with the exact error " "message being seen as well as the version of IOS " "being used."

ETHERCHANNEL_LB-3-XDR_MSG_XMIT_FAIL

3-Error

Failed to transmit XDR message of size [dec] to slot [dec]

An error occurred while attempting to send a load-balancing XDR message to the specified slot.

ether-channel

"Because the message failed to send the specified " "slot may now be out of sync with the rest of the " "system. To correct the issue the card in the " "specified slot may be rebooted at which point " "the full configuration will be re-synced with the " "card in that slot. If the specified slot is zero " "then that message was intended for cards in all " "slots and the router should be reloaded to re-sync" "the entire system."

SFF8472-2-NOMEM

2-Critical

Not enough memory available for [chars]

There has been a threshold violation as specified in the message.\n\ If the violation has occured only during bootup/OIR/link up/down\n\ you may ignore the message. Otherwise the violations in optical\n\ tx/rx power are most likely due to incompatible/defective\n\ optical components or too long/short optical cables. It may also\n\ be due to faulty transceiver.

-

LOG_STD_SH_TECH_ACTION

SFF8472-3-UNEXPECTEDEVENT

3-Error

Process received unknown event maj [hec] min [hec].

A process can register to be notified when various events occur in the\n\ router. This message indicates that a process received an event it\n\ did not know how to handle.

-

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SFF8472-3-INTERNAL_ERROR

3-Error

[chars]

The SFF8472 subsystem encountered an internal software\n\ error. The error message contains text which can be used\n\ to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

SFF8472-3-READ_ERROR

3-Error

[chars]

There was an error reading digital optical monitoring information\n\ from the transceiver at the specified interface.

-

"Please try removing and reinserting the transceiver.\n\ If it still does not work please replace the transceiver."

SFP-3-EEPROM_DUP_ERR

3-Error

SFP on ports [chars] and [chars] have duplicate serial numbers

The GBIC/SFP was identified as a Cisco GBIC but its vendor id and serial number match that of another GBIC on the system.

-

"Report to Cisco tech support."

SFP-4-EEPROM_READ_ERR

4-Warning

Error in reading SFP serial ID in [chars]

Error when reading SFP type from EEPROM

-

"Please remove SFP from this Port"

SFP-4-EEPROM_CRC_ERR

4-Warning

EEPROM checksum error for SFP in [chars]

The SFP in the port specified in the error message has invalid EEPROM data.

-

"Remove the SFP from the specified port."

SFP-4-EEPROM_SECURITY_ERR

4-Warning

SFP in [chars] failed security check

The SFP in the port specified in the error message has invalid EEPROM data.

-

"Remove the SFP from the specified port."

SFP-4-REMOVED

4-Warning

SFP module removed from [chars]

The online insertion and removal OIR facility detected the

-

LOG_STD_NO_ACTION

SFP-6-INSERTED

6-Information

SFP module inserted in [chars]

The online insertion and removal OIR facility detected a

-

LOG_STD_NO_ACTION

SFP-3-NOT_SUPPORTED

3-Error

Detected for SFP module in [chars] module disabled

The SFP module for the interface specified in the error message is not a cisco supported module. As a result of the error the module is disabled.

-

"Replace the module with a cisco supported SFP."

SFP-3-NOT_COMPATIBLE

3-Error

Detected for SFP module in [chars] module disabled

The SFP module for the interface specified in the error message is not compatible with the interface. As a result of the error the module is disabled.

-

"Replace the module with a compatible SFP."

CLEAR-5-COUNTERS

5-Notice

Clear counter on [chars] [chars] by [chars]

The counters have been cleared on the interfaces

-

LOG_STD_NO_ACTION

CLEAR-5-EXT_COUNT

5-Notice

Clear extended [chars] counters on [chars] by [chars]

The extended counters have been cleared on the interfaces

-

LOG_STD_NO_ACTION

CONTROLLER-5-UPDOWN

5-Notice

Controller [chars] changed state to [chars]

A configurable controller changed its state.

-

LOG_STD_NO_ACTION

CONTROLLER-5-DOWNDETAIL

5-Notice

Controller [chars] changed state to [chars] due to [chars]

A configurable controller changed its state.

-

LOG_STD_NO_ACTION

CONTROLLER-5-REMLOOP

5-Notice

Controller [chars] remote loop [chars] [chars]

A configurable controller entered remote loopback.

-

LOG_STD_NO_ACTION

CONTROLLER-5-REMLOCALLOOP

5-Notice

Controller [chars] local loop [chars] [chars]

A configurable controller entered local loopback.

-

LOG_STD_NO_ACTION

CONTROLLER-5-LOOPSTATUS

5-Notice

Controller [chars] [chars]

A configurable controller loopback status.

-

LOG_STD_NO_ACTION

CONTROLLER-2-CRASHED

2-Critical

Interface Processor in slot [dec] not responding [hec]: shutting it down

A controller stopped responding to commands over the cBus so it was\n\ put into shutdown mode.

-

"Re-enable the controllers by issuing the no shut\n\ configuration command on all controllers on the card or\n\ hotswap out the bad card and install the new one. You must\n\ still manually <CmdBold>no shut<noCmdBold> the controllers."

CONTROLLER-2-NOTFOUND

2-Critical

For controller [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

CONTROLLER-2-FIRMWARE

2-Critical

Controller [chars] [chars]

A software or hardware error occurred.

-

LOG_STD_SH_TECH_ACTION

CONTROLLER-5-CALLDROP

5-Notice

Controller [chars] [chars]

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CONTROLLER-5-HDLC_INSUFF_RESOURCE

5-Notice

Insufficient HDLC resources to enable channel [dec]

Limited number of HDLC channels can be allocated for this trunk

-

"Please check the number of HDLC resources supported for this trunk\n\ card. Please contact your technical support representative."

CONTROLLER-5-CLOCKSTATE

5-Notice

Controller [chars] [chars]

A configurable controller clock changed its state.

-

LOG_STD_NO_ACTION

CONTROLLER-2-CDB_NULL

2-Critical

cdb is NULL

A NULL pointer is detected

-

LOG_STD_SH_TECH_ACTION

CONTROLLER-2-DSX_NULL

2-Critical

dsx pointer is NULL

A NULL pointer is detected

-

LOG_STD_SH_TECH_ACTION

IFDAMP-5-UPDOWN

5-Notice

interface [chars] update [chars] state to [chars] interface is [chars]suppressed

dampening interface changed state.

ip

LOG_STD_NO_ACTION

IFDAMP-5-ZERODELAY

5-Notice

dampening reuse timer is updated with 0 delay time

Inconsistency of dampening reuse timer wheel

ip

LOG_STD_NO_ACTION

EC-5-MINLINKS_NOTMET

5-Notice

Port-channel [chars] is down bundled ports [dec] doesn't meet min-links

The administrative configuration of minimum links is greater than the\n\ number of bundled ports. Therefore this port channel has been brought\n\ down

fec

"Reduce the min-links configuration for this group\n\ or add more ports to this port-channel to have\n\ them bundle."

EC-5-MINLINKS_MET

5-Notice

Port-channel [chars] is up as its bundled ports [dec] meets min-links

The administrative configuration of minimum links is equal or less than\n\ the number of bundled ports. Therefore this port channel has been\n\ brought up

fec

"None."

EC-3-BWMISMATCH

3-Error

[chars] should be removed from the Port-channel[dec]

The member-link shouldn't have been part of the port-channel bundle\n\ because the bandwidth of the member-link doesn't match the bandwidth\n\ of the bundle. This configuration shouldn't have been allowed. This error\n\ indicates it was allowed due to some software issue.

fec

"Remove the member-link from the port-channel for\n\ proper operation."

TRANSCEIVER-3-INTERNAL_ERROR

3-Error

[chars]

This message indicates that the number of dynamically learned ARP entries complete or incomplete has exceeded a preconfigured threshold indicating a possible misconfiguration or DOS attack.

-

"First inspect the ARP entries on the affected interface. If they " "are valid entries either increase the configured log threshold or " "reconfigure the network to reduce ARP peers. " "If they are invalid entries there is a possible DOS attack " "on the system."

ARP-4-ARPLEARNTHRES

4-Warning

Learned ARP entries have reached to threshold level %lu

This message indicates that the number of dynamically learned ARP entries has reached a preconfigured max. limit in ARP Table.

-

"First inspect the ARP entries on the interface. If they are " "valid entries either increase the configured max limit or " "reconfigure the network to reduce ARP peers."

ARP-6-ARPLEARNRESUME

6-Information

Resuming Learn ARP entries to install in ARP table.

This message indicates that the number of dynamically learned ARP entries is in range of permit threshold value.System is allowing new Learned ARP entries to install in ARP table.

-

LOG_STD_NO_ACTION

ARP-3-STCKYARPOVR

3-Error

Attempt to overwrite Sticky ARP entry: [inet] hw: [enet] by hw: [enet]\n

Multiple stations configured with same IP in Private VLAN. Possible case of IP address stealing.

-

"Change the IP address of one of the two systems."

ARP-3-TABLEERR

3-Error

Internal software error during ARP table operation for ARP entry\n

An internal software error has occurred during an ARP table operation.

ip

LOG_STD_RECUR_ACTION

ARP-4-ARPADJ

4-Warning

Received CEF Adjacency updation request on different interfaces: [inet] on [chars]\n

A request to update CEF adjacency came on two different interfaces.

ip

LOG_STD_RECUR_ACTION

ARP-3-ARPINIT

3-Error

Internal software error during ARP subsystem initialization\n

An internal software error has occurred during ARP subsystem initialization.

ip

LOG_STD_RECUR_ACTION

ARP-3-ARPHAMSGFMT

3-Error

Malformed ARP HA checkpointing message size = [dec] entry count = [dec]\n

-

-

-

ARP-4-NULL_SRC_MAC

4-Warning

NULL MAC address from [inet] on [chars]

Application or peer tried to insert entry with NULL SRC MAC

ip

"If this message recurs call your technical support " "representative for assistance."

ARP-3-ARPINT

3-Error

ARP table accessed at interrupt level [dec]\n

ARP table is accessed at interrupt level which is forbidden.

ip

LOG_STD_RECUR_ACTION

ARP-3-ARPINVALIDEENTRY

3-Error

ARP system internal error. Returns NULL arp entry on node %p\n

An internal software error has occurred in ARP subsystem an NULL arp entry is got.

ip

LOG_STD_RECUR_ACTION

ARP-3-NULL_IF_INPUT

3-Error

ARP packet with NULL if_Input

ARP received a packet with NULL input interface

ip

"If this message recurs call your technical support " "representative for assistance."

GBIC_SECURITY_CRYPT-4-UNRECOGNIZED_VENDOR

4-Warning

GBIC in port [dec] manufactured by an unrecognized vendor

The GBIC was identified as a Cisco GBIC but the system was unable to match its manufacturer with one on the known list of Cisco GBIC vendors

firmware

"Check to see if the Cisco IOS software running on the system supports " "the GBIC. If the GBIC is newer a system software upgrade might be " "required."

GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR

4-Warning

GBIC in port [dec] has bad crc

The GBIC was identified as a Cisco GBIC but it does not have valid CRC in the EEPROM data.

firmware

"Check to see if the Cisco IOS software running on the system supports " "the GBIC. If the GBIC is newer a system software upgrade might be " "required. Even if the GBIC is unrecognized by the system the GBIC " "may still operate properly but might have limited functionality."

GBIC_SECURITY_CRYPT-4-ID_MISMATCH

4-Warning

Identification check failed for GBIC in port [dec]

The GBIC was identified as a Cisco GBIC but the system was unable to verify its identity

firmware

"Check to see if the Cisco IOS software running on the system supports " "the GBIC. If the GBIC is newer a system software upgrade might be " "required. Otherwise verify that the GBIC was obatined from Cisco or " "from a supported vendor."

VASI-2-DB_ENTRY_ALLOC_FAIL

2-Critical

VASI pair db entry allocation for interface [chars] failed

VASI pair database error. Memory chunk allocation for VASI pair database entry has failed.

asr1k-vasi

"Check for accurate memory management. " "Perform memory leak checks and " "look for memory corruption causes. " "Execute 'show proc memory' command."

VASI-2-DB_INSERT_FAIL

2-Critical

VASI pair db entry add for interface [chars] failed

VASI pair database error. Insertion of a new entry into VASI pair database has failed.

asr1k-vasi

"Check for accurate memory management. " "Perform memory leak checks " "look for memory corruption causes " "verify correct database management. " "Execute 'show proc memory' command."

VASI-2-DB_DELETE_FAIL

2-Critical

VASI pair db entry delete for interface [chars] failed

VASI pair database error. Removal of entry from VASI database has failed.

asr1k-vasi

"Check for accurate memory management. " "Perform memory leak checks " "look for mamory corruption causes and " "check for correct database management. " "Execute 'show proc memory' command. "

VASI-2-DB_ENTRY_FREE_FAIL

2-Critical

VASI pair entry free failed

VASI pair database error. Memory chunk free of VASI pair database entry has failed.

asr1k-vasi

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command."

VASI-2-DB_ALLOC_FAIL

2-Critical

VASI pair db allocation failed

VASI pair database error. Memory chunk creation for VASI pair database has failed.

asr1k-vasi

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command."

VASI-2-DB_DESTROY_FAIL

2-Critical

VASI pair database destroy failed

VASI pair database error. Memory chunk destroy has failed for VASI pair database.

asr1k-vasi

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute show proc memory command."

IF-3-IDB_LIST_BAD_REF_COUNT

3-Error

A bad reference count was encountered in an idb list element.

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IF-2-IDB_TABLE_INIT

2-Critical

Malloc failed while initializing idb table

-

-

-

IF-3-BAD_MTU

3-Error

Internal error. MTU on [chars] too large or negative. Truncating from %ld to %lu.\n

An internal software error occurred. The system attempted\n\ to set the MTU on an interface to an invalid value.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IF-3-BADLOCK

3-Error

Invalid lock use for [chars]: [chars][chars]

Application layer code attempted to access an unlocked interface.

-

"LOG_STD_ACTION"

IF-3-BADHWUNLOCK

3-Error

[chars] attempted to unlock [chars] [dec]. Locked by [chars] [dec].

Attempt to release semaphore held by another process.

-

"LOG_STD_ACTION"

IF-3-SEMAHOG

3-Error

[chars] could not get [chars] semaphore. Held by [chars].

Unable to obtain interface semaphore.

-

"LOG_STD_ACTION"

IF-4-BACKWARD_COUNTERS

4-Warning

Corrected for backward [chars] counters %llu -> %llu on [chars]

-

-

-

IF-3-BADMACADDRTYPE

3-Error

illegal mac address type [dec]

This is an interal error that was recovered gracefully.

idb

"LOG_STD_ACTION"

IF-4-NOBGPROCESS

4-Warning

Network background process not running. [chars]

A process which manages network interface background processing is not yet running but another system process has tried to send the process a message.

idb

"An interface on the router may have missed a request to bring " "itself up. If that happens it may be necessary to reset the " "interface using a <CmdBold>shutdown<NoCmdBold> operation and " "then a <CmdBold>no shutdown<NoCmdBold>. "

SLIP-2-BADSTATE

2-Critical

Impossible input state [hec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SLIP-2-BADQUOTE

2-Critical

Impossible quoted character [hec]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

LINEPROTO-5-UPDOWN

5-Notice

Line protocol on Interface [chars] changed state to [chars]

The data link level line protocol changed state.

-

LOG_STD_NO_ACTION

GBIC_SECURITY-4-GBIC_INTERR

4-Warning

Internal error occurred in setup for GBIC interface [chars]

The system could not allocate resources or had some other problem in the setup for the specified GBIC interface.

firmware

"Reload the system. If the problem persists " "contact TAC."

GBIC_SECURITY-4-EEPROM_READ_ERR

4-Warning

Error in reading GBIC serial ID in [chars]

Error when reading GBIC type from EEPROM

-

"Please remove GBIC from this Port"

GBIC_SECURITY-4-EEPROM_CRC_ERR

4-Warning

EEPROM checksum error for GBIC in [chars]

The GBIC in the port specified in the error message has invalid EEPROM data.

-

"Remove the GBIC from the specified port."

GBIC_SECURITY-4-EEPROM_SECURITY_ERR

4-Warning

GBIC in [chars] failed security check

The GBIC in the port specified in the error message has invalid EEPROM data.

-

"Remove the GBIC from the specified port."

IFMGR-3-IFINDEX_PERSIST_ENTRY_CORRUPT

3-Error

[chars] seems to be corrupted. Trying to read [dec] size

The ifIndex-table seems to be corrupted.

if_mgr

"Delete the ifindex-table."

IFMGR-3-INVALID_PERSISTENT_DATA

3-Error

Invalid persistent data

Trying to write invalid persistent data

snmp-if

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

IFMGR-3-NOVECTOR

3-Error

Interface manager failed to allocate IF vector. size [dec]

The interface vector was not able to be allocated with the number of elements required--initially or resize see size in the error message.

if_mgr

"TBD"

IFMGR-3-VECTOREXD

3-Error

IF manager attempted to use interface [dec] outside vector range.

This message indicates that an interface with too large of an ifIndex value was attempted to be added to the IF-MGR DB.

if_mgr

"Additional IF-MGR warning and/or error messages should accompany" "indication of this error. These additional messages should provide more" "details on the effected interface."

IFMGR-3-VECTORPOSUSED

3-Error

IF manager attempted to add interface [dec] which was already added.

This message comes from the IF-MGR DB when it is trying to add an ifIndex value for this interface which already exists in the ifIndex DB.

if_mgr

"TBD"

IFMGR-4-VECTORIFSUSPECT

4-Warning

IF manager added interface [dec] which is unexpectedly large.

The ifIndex allocation scheme gives out sequential ifIndex values. This message comes from the IF-MGR DB when it is trying to add an ifIndex value much larger than the former greatest ifIndex value in the DB.

if_mgr

"TBD"

IFMGR-3-IFDB

3-Error

IF manager interface database [chars] failure- [dec]

-

if_mgr

"TBD"

IFMGR-3-IFTDB

3-Error

IF manager interface table database [chars] failure- [dec]

-

if_mgr

"TBD"

IFMGR-3-NOTYPEVECTOR

3-Error

Interface manager failed to allocate IF type vector. size [dec]

The interface type vector was not able to be allocated with the number of elements required--initially or resize.

if_mgr

"TBD"

IFMGR-3-NOIMACP

3-Error

IF manager control process failed to start

-

if_mgr

"TBD"

IFMGR-4-NOIFINDEX

4-Warning

All SNMP if indices are exhausted

All SNMP MIB indices have been exhausted. Interfaces will\n\ not be able to obtain an interface index that they can \n\ use to register with the interface MIB.

if_mgr

"Attempt a system reload. If the problem persists after the\n\ system reload copy the message exactly as it appears on\n\ the console or in the system log contact your Cisco\n\ technical support representative and provide the\n\ representative with the gathered information."

IFMGR-3-BADIFINDEXTABLE

3-Error

The file nvram:ifIndex-table is corrupt.

The file is not in the expected format.

none

"If possible please delete the file."

IFMGR-4-NOSYNC

4-Warning

ifIndex not being synced between active and standby

When the standby comes up then the tuple of ifIndex and ifDescr\n\ is synced so that when interfaces comes up they get the same ifIndex.\n\ This error happens when the interface doesn't get the ifIndex for\n\ the given ifDescr

if_mgr

"Inform the technical support to raise the ddts"

IFMGR-5-RESTART

5-Notice

[chars]

The IF MGR process has restarted

if_mgr

"This is an informational message. The system should recover on its" " own."

IFMGR-4-STACK_RELATIONSHIP_ADD_ERROR

4-Warning

[chars]: Request for creating invalid stack relationship [dec] [dec]

Interfaces have same ifIndex in IF-MGR assigned list. The 2nd interface registered with IF-MGR will be assigned with new index

if_mgr

"1. No Action if ifIndex persist is not required." "2. Reload the standby RP if ERR msg only seen in standby RP" "3. Reload the router with the proper ifindex-table and image"

IFMGR-7-NO_IFINDEX_FILE

7-Debug

Unable to open [chars] [chars]

This is a informational message. This means system found no saved ifIndex information and ifIndex is not persisted across reboots. The ifIndices will be reassigned.

if_mgr

"1. No Action if 'snmp-server ifIndex persist' is not configured. " "2. If 'snmp-server ifindex persist' is configured then copy the error" " message exactly as it appears and report it to your technical" " support representative."

OTNMGR-3-OTN_STATS_CREATE_IF_FAILED_TO_ALLOCATE

3-Error

stats for interface index [dec] could not be created with status [dec]

-

snmp-otn

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

OTNMGR-3-OTN_STATS_CREATE_IF_FAIL

3-Error

stats for interface index [dec] could not be created with status [dec]

-

snmp-otn

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

OTNMGR-3-OTN_STATS_DELETE_IF_FAIL

3-Error

stats for interface index [dec] could not be deleted with status [dec]

-

snmp-otn

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

IFS-4-FILEMAX

4-Warning

Failed to open [chars] maximum open files [dec]

The router has reached the maximum number of files that may\n\ be open at one time.

ifs

"Close some files and try again. If this messages recurs contact your\n\ technical support representative."

IFS-3-FSMAX

3-Error

Failed to add [chars] maximum filesystems [dec]

The router has reached the maximum number of file systems that\n\ can be supported at one time.

ifs

"Contact your technical support representative."

IFS-3-FSDUP

3-Error

Failed to add [chars] filesystem prefix exists

A file system cound not be added because another file system exists\n\ with the same name.

Determine the component from the traceback displayed in the\n\ error message.

"Contact your technical support representative."

IFS-3-FS_CREATE_FAIL

3-Error

Failed to create [chars] file system [chars]

An internal software error occurred.

Determine the component from the traceback displayed in the\n\ error message.

"Call your technical support representative for assistance."

IFS-3-FS_CREATE_FAIL2

3-Error

Failed to create [chars] simple file system [chars]

An internal software error occurred.

Determine the component from the traceback displayed in the\n\ error message.

"Call your technical support representative for assistance."

IFS-3-FS_MISSING_FUNCTIONS

3-Error

'[chars]' file system missing required functions not created

Some file systems require a certain set of function to be present in\n\ order to be usable. This file sustem does not support all the\n\ mandatory functionality.

Determine the component from the traceback displayed in the\n\ error message.

"Call your technical support representative for assistance."

IFS-3-FS_STRUCT_ERROR

3-Error

Data does not match expected internal representation

A mismatch exists between the representation of data extracted from the filesystem and the expectation of its formatting. This may occur when running in a dual-RP environment with different IOS versions running on the two RPs.

ifs

"Ensure both RPs are running the IOS same version if running in " "a dual-RP environment. If not call your technical support " "representative for assistance."

TAR_FS-3-IMAGE_FILE_INVALID

3-Error

[chars] file not found in archive

The Tar File System could not locate the relevant tar element inside the archive

os

"Check whether the Archive is complete and not corrupted or of" " the wrong format. If the problem could" " be recreated with <CmdBold>debug ifs file<NoCmdBold> turned" " on it could help in quick identification of the problem." " Collect the output of <CmdBold>archive tar" " /table<NoCmdBold> <CmdArg>archive-name<NoCmdArg> if it is a" " pure tar archive or <CmdBold>show image contents file<NoCmdBold>" " <CmdArg>archive-name<NoCmdArg> if the archive is a system image"

SIGNATURE-3-ABORT_OPER

3-Error

%%ERROR: Aborting [chars].

The system is aborting the specified operation because it failed to verify a valid signature in the image file.

security

"Attempt to restart the operation by using an image file " "with a valid signature. A valid signature ensures the " "integrity of the image."

SIGNATURE-3-CONTINUE_OPER

3-Error

%%ERROR: Continuing Operation [chars] in spite of failure.

Although the system failed to verify a valid signature in the image file the user decided to continue the specified operation. A valid signature ensures the integrity of the image.

security

-

SIGNATURE-4-NOT_PRESENT

4-Warning

%%WARNING: Signature not found in file [chars].

The specified image file does not have a signature. Only Cisco IOS Software images in Executable and Linkable format are signed. Releases that do not support the image verification feature do not contain a signature in the image file. If you enter <CmdBold>verify<NoCmdBold> <CmdBold>copy<NoCmdBold> or <CmdBold>reload<NoCmdBold> command and the specified file is not a Cisco IOS Software image in Executable and Linkable format or of an earlier release the system displays this warning message because the file does not have a signature. A valid signature ensures the integrity of the image.

security

\" to see if the image that you are " "using supports the image verification feature."

SIGNATURE-3-NOT_VALID

3-Error

%%ERROR: Signature not valid for file [chars].

The specified Cisco IOS Software image has an invalid signature. A valid signature ensures the integrity of the image.

security

"Do not use this file. The file might be corrupted or " "modified. Attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assisstance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "contact your Cisco technical support representative with the " "information you have gathered."

SIGNATURE-3-NOT_ABLE_TO_PROCESS

3-Error

%%ERROR: Not able to process Signature in [chars].

An unknown error occurred when the system attempted to process the signature in the specified image file. A valid signature ensures the integrity of the image.

security

"Do not use this file. The file might be corrupted or " "modified. Attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assisstance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "contact your Cisco technical support representative with the " "information you have gathered."

SIGNATURE-4-UNKNOWN

4-Warning

%%WARNING: Found unknown signature type 0x[hec] in file [chars]\n Skipping the signature.

If the desired image belongs to a later release than the running image the desired image might have a newer signature type. A valid signature ensures the integrity of the image.

security

\" to see if a signature of the type " "specified was added."

SIGNATURE-3-DELETE_FAILED

3-Error

%%ERROR: Unable to auto delete file [chars]. Remove file manually

The specified Cisco IOS Software image file contains an invalid signature but automatic deletion of the file has failed. A valid signature ensures the integrity of the image.

security

"Delete the file by entering the <CmdBold>delete<NoCmdBold> command."

ILPOWER-3-ILPOWER_INTERNAL_IF_ERROR

3-Error

Inline Power internal error interface [chars]: [chars]

A software check failed during Power over Ethernet PoE processing.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-5-ILPOWER_POWER_DENY

5-Notice

Interface [chars]: inline power denied. Reason: [chars]

There is not enough power remaining in the switch to supply to\n\ the Power over Ethernet PoE port.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-ILPOWER_POWER_CDP_SHUT

5-Notice

Interface [chars]: inline power shut

-

inline-power

LOG_STD_NO_ACTION

ILPOWER-3-CONTROLLER_ERR

3-Error

Controller error Controller number [dec]: [chars]

An error reported or caused by the Power over Ethernet PoE controller is detected.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-3-CONTROLLER_POST_ERR

3-Error

Inline Power Feature is disabled on this switch because\n\ Power On Self Test POST failed on this switch.\n\msgdef_explanation An error reported or caused by the Power over Ethernet

-

-

-

ILPOWER-3-CONTROLLER_IF_ERR

3-Error

Controller interface error [chars]: [chars]

An interface error is detected between the Power over Ethernet PoE controller and system.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-3-CONTROLLER_PORT_ERR

3-Error

Controller port error Interface [chars]: [chars]

A port error reported by the Power over Ethernet PoE controller is detected.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-5-POWER_GRANTED

5-Notice

Interface [chars]: Power granted

There is enough power available in the switch and\n\ the switch is providing power on the interface.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-LINKDOWN_DISCONNECT

5-Notice

Interface [chars]: Link down disconnect

The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-IEEE_DISCONNECT

5-Notice

Interface [chars]: PD removed

The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface.

inline-power

LOG_STD_NO_ACTION

ILPOWER-7-DETECT

7-Debug

Interface [chars]: Power Device detected: [chars]

The switch has detected the attached power device.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-INVALID_IEEE_CLASS

5-Notice

Interface [chars]: has detected invalid IEEE class: [dec] device. Power denied

The power device has invalid IEEE class. switch won't power\n\up the device

-

LOG_STD_NO_ACTION

ILPOWER-3-SHUT_OVERDRAWN

3-Error

Interface [chars] is shutdown as it is consuming more than the maximum configured power [dec] milliwatts.

Interface is shutdown because it is consuming more than the maximum configured power

inline-power

"Make sure correct power is budgeted for this interfac\n\e based on the power device electrical specifications or ratings. It is recommended to change the police cutoff power to a higher value to keep the device powered on"

ILPOWER-4-LOG_OVERDRAWN

4-Warning

Interface [chars] is overdrawing power. it is consuming [dec] milliwatts where as maximum configured power is [dec] milliwatts.

-

inline-power

"Make sure correct power is budgeted for this interface based on the power device electrical specifications or ratings. Otherwise you might risk overloading the switch. It is recommended to change the police cutoffpower appropriately if needed"

ILPOWER-5-CLR_OVERDRAWN

5-Notice

Interface [chars] is NOT overdrawing power. it is consuming [dec] milliwatts where as maximum configured value is [dec] milliwatts.

-

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-POLICE_POWER_INVALID

5-Notice

Interface [chars]: invalid power police [dec] milliwatts current [dec] mA voltage [dec] mV

power policing current or voltage value is invalid.

-

LOG_STD_SH_TECH_ACTION

ILPOWER-5-SENSE_POWER_INVALID

5-Notice

Interface [chars]: invalid power sense [dec] milliwatts current [dec] mA voltage [dec] mV

power sensing current or voltage value is invalid.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-4-ILPOWER_POWER_SUPPLY

4-Warning

PoE Power Supply [chars]: [chars]

The power supply for PoE is OIR

inline-power

"Make sure power supply to PoE input is inserted after removal"

ILPOWER-4-ILPOWER_PS_ABSENCE

4-Warning

PoE module Power Supply not present \n\ Inline Power Feature is disabled on [chars] because Power On Self Test POST failed \n : [chars]

The power supply for PoE expansion module is not present or not inserted properly or faulty

inline-power

"Make sure power supply to expansion module is inserted properly\ and reload the switch with PoE power supply present"

ILPOWER-5-PWRGOOD_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power good

Spare pair power request was successful and power is available on spare pair

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-TSTART_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power error: TSTART

spare pair tstart error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-PGOOD_TIMEOUT_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power good timeout error

spare pair power good timeout error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-DET_SHORT_SPARE_PAIR

5-Notice

Interface [chars]: spare pair short detected

spare pair short detect error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-DET_TIMEOUT_SPARE_PAIR

5-Notice

Interface [chars]: spare pair detect timeout

spare pair timeout detect error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

RE-4-COMPILE_FAILED

4-Warning

Compile failed on pattern number [dec] - states [dec] - [chars]

Triggers when RE memory cannot be allocated.

ids

"This message indicates that space for the\n\ specified RE cannot be allocated due to memory limitations."

APPFW-4-HTTP_STRICT_PROTOCOL

4-Warning

Sig:[dec] HTTP protocol violation detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the strict-http \n\ application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_CONT_LENGTH

4-Warning

content-length

The HTTP message has been detected to violate the content-length \n\ application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_CONT_TYPE_VERIFY

4-Warning

Sig:[dec] Content type does not match the specified type - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_MATCH_REQ_RESP

4-Warning

Sig:[dec] Content type: [chars] does not match the Accept-Type from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_CONT_TYPE_MATCH

4-Warning

Sig:[dec] Content type not found - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_CONT_TYPE_SIZE

4-Warning

Sig:[dec] Content size %lu out of range - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_MAX_HDR_LEN

4-Warning

Sig:[dec] HTTP Header length exceeded. Received %lu byte of header - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ max-hdr-len application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_MAX_URI_LEN

4-Warning

Sig:[dec] HTTP URI length exceeded. Received %lu byte of URL - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ max-uri-len application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_REQ_METHOD_RFC

4-Warning

Sig:[dec] HTTP RFC method illegal - [chars] '[chars]' from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ request-method application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_REQ_METHOD_EXT

4-Warning

Sig:[dec] HTTP Extension method illegal - [chars] '[chars]' from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ request-method application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_PORT_MISUSE_IM

4-Warning

Sig:[dec] HTTP Instant Messenger detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ port misuse application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_PORT_MISUSE_P2P

4-Warning

Sig:[dec] HTTP Peer-to-Peer detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ port misuse application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_PORT_MISUSE_TUNNEL

4-Warning

Sig:[dec] HTTP Tunnel detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ port misuse application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_TRANSFER_ENCODE

4-Warning

Sig:[dec] HTTP Transfer encoding violation detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ transfer encoding application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-4-HTTP_DEOBFUSCATE

4-Warning

Sig:[dec] Deobfuscation signature detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ deobfuscate application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-3-HTTP_MAX_REQ_EXCEED

3-Error

Maximum of [dec] unanswered HTTP requests exceeded from [inet]:[dec] to [inet]:[dec]

The HTTP message has been detected to violate the \n\ transfer encoding application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-6-HTTP_SESSION_AUDIT_TRAIL

6-Information

HTTP session initiator [inet]:[dec] sends [dec] bytes - responder [inet]:[dec] sends [dec] bytes

The HTTP message has been detected to violate the \n\ transfer encoding application firewall inspection rule.

appfw

"This message is for informational purposed only but may indicate \n\ a security problem."

APPFW-3-HTTP_APPFW_CONF_ERROR

3-Error

Application Firewall configuration error -- [chars]

An error has occurred during Application Firewall configuration.

appfw

"This message indicates an error during firewall configuration " "and may be a potential security problem."

URLF-6-SITE_ALLOWED

6-Information

[chars]Client [inet]:[dec] accessed server [inet]:[dec]

This message indicates that all URLs belongs to the server are allowed to be passed with out URL filter servers authentication

ios-firewall

"This message is just for informational purpose it can be used " "to keep track of number of GET request that are sent from client " "to server"

URLF-4-SITE_BLOCKED

4-Warning

[chars]Access denied for the site '[chars]' client [inet]:[dec] server [inet]:[dec]

This message indicates that all underlying URLs of the specified domain are blocked

ios-firewall

"This indicates that an user has made an attempt to browse a " "forbidden site"

URLF-6-URL_ALLOWED

6-Information

[chars]Access allowed for URL '[chars]' client [inet]:[dec] server [inet]:[dec]

This message indicates that the http GET request sent from client is allowed to be transmitted to http server

ios-firewall

"This is just an informational message"

URLF-4-URL_BLOCKED

4-Warning

[chars]Access denied URL '[chars]' client [inet]:[dec] server [inet]:[dec]

This message indicates that access to the requested URL is denied and the corresponding TCP connection is closed

ios-firewall

"This indicates that an user has made an attempt to browse a " "forbidden site"

URLF-3-SERVER_DOWN

3-Error

[chars]Connection to the URL filter server [inet] is down

This messages indicates that a connection between the router and a url filter server is down. If more than one servers are configured the router will make use of other servers for URL authentication otherwise it will check whether allow mode is 'on' or 'off'. If allow mode is 'on' the router will pass all the packets otherwise it will drop all the packet and close the TCP connection.

ios-firewall

"The network administrator can possibly check whether the URL filter " "server WebSense/N2H2 is down and restart it if required. If it "

URLF-3-ALLOW_MODE

3-Error

[chars]Connection to all the URL filter servers are down and the allow mode is '[chars]'

This messages indicates that connection to all the URL filter servers are down. If allow mode is 'on' the router will pass all the http traffic otherwise it will drop the http traffic and close the TCP connection

ios-firewall

"The network administrator can possibly check whether the URL filter " "server WebSense/N2H2 is down and restart it if required. If it "

URLF-5-SERVER_UP

5-Notice

[chars]Connection to an URL filter server[inet] is made the router is

This message indicates that at least one connection is up between router and a URL filter server. System is leaving out of allow mode

ios-firewall

"This is just an informational message"

URLF-3-URL_TOO_LONG

3-Error

[chars]URL sent from [inet] is too long more than [dec] bytes possibly

The URL parsed from http GET request is too long it could possibly be a fake packet so the packet will be dropped

ios-firewall

"This could be a fake packet sent by the attackers"

URLF-3-MAX_REQ

3-Error

[chars]The number of pending request exceeds the maximum limit [dec]

This message indicates that the number of requests pending in the router for URL authentication from URL filter server exceeds the maximum limit. In this case the http request will be dropped

ios-firewall

"This message is just for informational purpose"

URLF-3-RESOURCE_ALLOC_FAILED

3-Error

The resource allocation failed for URL filter subsystem

This message indicates that the URLF feature is not able to allocate memory for various data structures

ios-firewall

"The router is running out of memory disable " "the features that are not used or check if something goes wrong"

FW-4-ALERT_ON

4-Warning

[chars][chars] count [dec]/[dec] current 1-min rate: [dec]

Either the max-incomplete high threshold of half-open connections \n\ or the new connection initiation rate has been exceeded. This error \n\ message indicates that an unusually high rate of new connections is \n\ coming through the firewall and a DOS attack may be in progress. \n\ This message is issued only when the max-incomplete high threshold \n\ is crossed.

firewall

"This message is for informational purposed only but may indicate \n\ a security problem."

FW-4-ALERT_OFF

4-Warning

[chars][chars] count [dec]/[dec] current 1-min rate: [dec]

Either the number of half-open connections or the new connection \n\ initiation rate has gone below the max-incomplete low threshold. \n\ This message indicates that the rate of incoming new connections \n\ has slowed down and is issued only when the max-incomplete low \n\ threshold is crossed.

firewall

"This message is for informational purposed only but may indicate \n\ that an attack has stopped."

FW-4-HOST_TCP_ALERT_ON

4-Warning

[chars]Max tcp half-open connections [dec] exceeded for host [inet].

The max-incomplete host limit of half-open TCP connections has been \n\ exceeded. This message indicates that a high number of half-open \n\ connections is coming to the protected server and may indicate \n\ that a SYN flood attack is in progress and is targeted to the \n\ specified server host.

firewall

"This message is for informational purposes only but may indicate \n\ that a SYN flood attack was attempted. If this alert is issued \n\ frequently and identified to be mostly false alarms then the \n\ max-incomplete host threshold value is probably set too low \n\ and there is a lot of legitimate traffic coming in to that server. \n\ In this case the max-incomplete host parameter should be set to \n\ a higher number to avoid false alarms."

FW-2-BLOCK_HOST

2-Critical

[chars]Blocking new TCP connections to host [inet] for [dec] minute[chars] half-open count [dec] exceeded.

This message indicates that any subsequent new TCP connection \n\ attempts to the specified host will be denied because the \n\ max-incomplete host threshold of half-open TCP connections is \n\ exceeded and the blocking option is configured to block the \n\ subsequent new connections. The blocking will be removed when the \n\ configured block-time expires.

firewall

"This message is for informational purposes only but may indicate \n\ that a SYN flood attack was attempted."

FW-4-UNBLOCK_HOST

4-Warning

[chars]New TCP connections to host [inet] no longer blocked

New TCP connection attempts to the specified host are no longer \n\ blocked. This message indicates that the blocking of new TCP \n\ attempts to the specified host has been lifted.

firewall

"This message is for informational purposed only but may indicate \n\ a SYN flood attack was attempted to the host."

FW-3-NOTFOUND

3-Error

[chars]Session context for [inet]:[dec] => [inet]:[dec] not found.

The CBAC code was searching its database for information for a \n\ particular inspection session but this information was not found.

firewall

"If this message recurs copy it down exactly as it appears and \n\ contact your technical support representative for assistance."

FW-6-SESS_AUDIT_TRAIL_START

6-Information

[chars]Start [chars] session: initiator [inet]:[dec] -- responder [inet]:[dec]

This message documents the opening of an inspection session.\n\ The message is issued at the start of each inspected session\n\ and it records the source/destination addresses and ports.

firewall

"This message is for informational purposed only and can be used \n\ to collect the basic accounting for inspected sessions."

FW-6-SESS_AUDIT_TRAIL

6-Information

[chars]Stop [chars] session: initiator [inet]:[dec] sent [dec] bytes -- responder [inet]:[dec] sent [dec] bytes

This message documents the per-session transaction log of network \n\ activities. The message is issued at the end of each inspected \n\ session and it records the source/destination addresses and ports \n\ as well as the number of bytes transmitted by the client and \n\ server.

firewall

"This message is for informational purposed only and can be used \n\ to collect the basic accounting for the inspected sessions."

FW-3-FTP_SESSION_NOT_AUTHENTICATED

3-Error

[chars]Command issued before the session is authenticated -- FTP client [inet] FTP server [inet]

An FTP client attempted to use the PORT command or an FTP server \n\ attempted to use the response to a PASV command to open a data \n\ channel in the firewall prior to the client's successful \n\ authentication with the server. This is a suspicious attempt by \n\ the client/server to trick the firewall into opening a hole \n\ so that outside attackers can take advantage of the firewall \n\ opening. This message indicates that a suspicious violation was \n\ detected and the PORT or PASV command/response is rejected \n\ by the firewall. The data channel in the firewall will not be \n\ opened until the authentication is done successfully.

firewall

"This message is for informational purposes only but may indicate \n\ that an illegal attempt was made to modify the firewall security \n\ policy."

FW-3-FTP_PRIV_PORT

3-Error

[chars]Privileged port [dec] used in [chars] -- FTP client [inet] FTP server [inet]

An FTP client attempted to use a PORT command or the FTP server \n\ attempted to use the response to a PASV command to trick the \n\ firewall into opening access to a privileged port. This message \n\ indicates that a suspicious violation was detected from the FTP \n\ client/server attempting to modify the security policy in the \n\ firewall. The command is rejected and the connection is reset by \n\ the firewall.

firewall

"This message is for informational purposes only but may indicate that an attempt was made to gain access to privileged ports."

FW-3-FTP_NON_MATCHING_IP_ADDR

3-Error

[chars]Non-matching address [inet] used in [chars] -- FTP client [inet] FTP server [inet]

An FTP client attempted to use a PORT command or the FTP server \n\ attempted to use the response to a PASV command to trick the \n\ firewall into opening access to a third-party host that is \n\ different from the two hosts engaged in the FTP connection. \n\ This message indicates that a suspicious violation was detected \n\ while attempting to modify the security policy in the firewall. \n\ The command is rejected and the connection is reset by the \n\ firewall.

firewall

"This message is for informational purposes only but may indicate \n\ that an attempt was made to grant or open access to unauthorized \n\ hosts."

FW-3-SMTP_INVALID_COMMAND

3-Error

[chars]Invalid SMTP command [chars]total [dec] chars from initiator [inet]:[dec]

The CBAC code detected an invalid SMTP command in the inspected \n\ SMTP connection. This message indicates that a suspicious violation \n\ was detetected that may be an attack to the mail server system. \n\ The command is rejected and the connection is reset by the firewall \n\ immediately.

firewall

"This message is for informational purposes only but may indicate\n\ a security problem."

FW-3-HTTP_JAVA_BLOCK

3-Error

[chars]JAVA applet is blocked from [inet]:[dec] to [inet]:[dec].

A Java applet was seen in the HTTP channel and the firewall \n\ configuration indicates that the applet from this Web site should \n\ be prohibited. The message indicates that the applet is being \n\ downloaded from one of the prohibited sites and its entrance to \n\ the protected network is not allowed. The connection is reset and \n\ the transmission of the detected applet is aborted immediately.

firewall

"This message is for informational purposes only but may indicate a security problem."

FW-4-TCP_SENDMAIL_BAD_TO_SIG

4-Warning

[chars]Sendmail Invalid Recipient - from [inet] to [inet]

-

firewall

"For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately."

FW-4-TCP_SENDMAIL_BAD_FROM_SIG

4-Warning

[chars]Sendmail Invalid Sender - from [inet] to [inet]

-

firewall

"For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately."

FW-4-TCP_SENDMAIL_OLD_SIG

4-Warning

[chars]Archaic Sendmail Attacks - from [inet] to [inet]

Triggers when ''wiz'' or ''debug'' commands are sent to the SMTP port.

firewall

"For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately."

FW-4-TCP_SENDMAIL_DECODE

4-Warning

[chars]Sendmail Decode Alias - from [inet] to [inet]

Triggers on any mail message with '': decode@'' in the header.\n\ The decode alias is used to uudecode files and is primarily\n\ implemented as a convenience for system administration.

firewall

"For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately."

FW-4-TCP_MAJORDOMO_EXEC_BUG

4-Warning

[chars]Majordomo Execute Attack - from [inet] to [inet]

A bug in the Majordomo program will allow remote users to\n\ execute arbitrary commands at the privilege level of the\n\ server.

firewall

"For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately."

FW-4-TCP_SENDMAIL_INVALID_COMMAND

4-Warning

[chars]Invalid SMTP command - [inet] to [inet]

Triggers on an invalid SMTP command in the \n\ SMTP connection. This message indicates that a suspicious violation \n\ was detetected that may be an attack to the mail server system.

firewall

"This is unusual traffic and may warrant\n\investigation."

FW-6-PRE_ALLOCATED_MEDIA_CHANNEL

6-Information

[chars]Pre-Allocated [chars] channel from [inet][[dec]:[dec]] to [inet][[dec]:[dec]]

Firewall inspection is configured on at least one interface in the\n\ startup config.

firewall

"This message is for informational purposes only. \n\ It may be used to verify whether firewall inspection is on at startup."

FW-6-DROP_PKT

6-Information

Dropping [chars] pkt [inet]:[dec] => [inet]:[dec]

Packet dropped by firewall inspection.

firewall

"This message is for informational purposes only. \n\ It may be used to verify that packets were dropped by the firewall."

FW-5-POP3_INVALID_COMMAND

5-Notice

[chars]Invalid POP3 command from initiator [inet]:[dec]: [chars]

-

-

-

FW-5-POP3_NON_SECURE_LOGIN

5-Notice

[chars]LOGON POP3 command from initiator [inet]:[dec]: [chars]

The CBAC code detected a cleartext logon attempt in the inspected POP3\n\ connection while secure-login is configured.\n\ The command is rejected and the connection is reset by the firewall\n\ immediately.

firewall

"This message is for informational purposes only but may indicate a\n\ security problem."

FW-5-IMAP_INVALID_COMMAND

5-Notice

[chars]Invalid IMAP command from initiator [inet]:[dec]: [chars]

-

-

-

FW-5-IMAP_NON_SECURE_LOGIN

5-Notice

[chars]LOGON IMAP command from initiator [inet]:[dec]: [chars]

The CBAC code detected a cleartext logon attempt in the inspected IMAP\n\ connection while secure-login is configured.\n\ The command is rejected and the connection is reset by the firewall\n\ immediately.

firewall

"This message is for informational purposes only but may indicate a\n\ security problem."

FW-4-SESSION_THRESHOLD_EXCEEDED

4-Warning

[chars]Number of sessions for the firewall rule '[chars]' applied on interface '[chars]' exceeds the configured threshold [dec]

This message indicates that the number of established CBAC\n\ sessions have crossed the configured threshold.

firewall

"This message is for informational purpose only but may indicate\n\ a security problem. This might also mean that the session threshold\n\ is set to a low value in which case the threshold value could be\n\ increased through CLI command"

FW-5-EMAIL_DROP_FRAGMENT

5-Notice

[chars]Dropping [chars] command fragment from initiator [inet]:[dec]

-

-

-

FW-3-INTERNAL_ERROR

3-Error

IP Firewall internal failure -- [chars]

This message indicates the misc errors in the IP FW subsystem

firewall

"This message indicates the misc errors in the IP FW subsystem"

FW-3-TIMER_WHEEL_INIT_FAILED

3-Error

Timer Wheel initialization failed

This message indicates that Timer Wheel initialization is\n\ failed in the FW subsystem

-

"This message indicates a series problem with IOS Firewall. \n\ On seeing this error message copy the message exactly as \n\ it appears and report it to your technical support \n\ representative."

FW-3-RESPONDER_WND_SCALE_INI_NO_SCALE

3-Error

Dropping packet - Invalid Window Scale option for session [inet]:[dec] to [inet]:[dec] Initiator scale [dec] Responder scale [dec]

Firewall detected the packet from Responder to Initiator \n\ has windows scaling option but did not have the scaling \n\ option in the SYN packet from Initiator to responder. \n\ This is an error according to RFC 1323

firewall

"Turn on window scaling option on both Initiator" " and Responderor Turn off window scaling on the" " Responder"

APPFW-6-IM_YAHOO_SESSION

6-Information

im-yahoo [chars] service session initiator [inet]:[dec] [chars] [dec] bytes [chars] responder [inet]:[dec]

The YMSGR well known service message has been detected.

appfw

"This message is for informational purposed only."

APPFW-6-IM_YAHOO_P2P_CHAT

6-Information

im-yahoo text-chat service session: [inet]:[dec] establishing a direct chat with [dec].[dec].[dec].[dec]

A specific service yyyy has been detected to establish\n\ a direct connection with another peer in a Yahoo! Instant Messenger \n\ application and the application firewall inspection policy has been\n\ configured to send an alarm for this event. Typical services are ñ \n\ text-chat voice-chat file-transfer etc.

appfw

"This message is for informational purposed only."

APPFW-6-IM_AOL_SESSION

6-Information

im-aol [chars] service session initiator [inet]:[dec] [chars] [dec] bytes [chars] responder [inet]:[dec]

The AIM well known service message has been detected.

appfw

"This message is for informational purposed only."

APPFW-6-IM_MSN_SESSION

6-Information

im-msn [chars] service session initiator [inet]:[dec] [chars] [dec] bytes [chars] responder [inet]:[dec]

The MSNMSGR well known service message has been detected.

appfw

"This message is for informational purposed only."

APPFW-6-IM_YAHOO_CLIENT_VERSION

6-Information

im-yahoo [inet]:[dec] attempting to establish connection with yahoo server [inet]:[dec] using an unsupported version of the client

The YAHOO client version is not supported

appfw

"This message is for informational purposed only."

APPFW-6-IM_MSN_CLIENT_VERSION

6-Information

im-msn [inet]:[dec] attempting to establish connection with msn server [inet]:[dec] using an unsupported version of the client

The MSN client version is not supported

appfw

"This message is for informational purposed only."

APPFW-6-IM_AOL_CLIENT_VERSION

6-Information

im-aol [inet]:[dec] attempting to establish connection with aol server [inet]:[dec] using an unsupported version of the client

The AOL client version is not supported

appfw

"This message is for informational purposed only."

FW_HA-3-SUBSYS_INIT_FAILED

3-Error

Firewall High availability subsystem initialization failed

Firewall High Availability subsystem initialization failed

ios-firewall

"Firewall HA subsystem initialization failed under unsual circumstances \n\ Check the available memory and CPU utilization on the router and verify \n\ that it satisfies the requirements for the feature \n\ If the requirement are satisfied collect the output of show tac and \n\ report it to Cisco Technical assistance centre."

FW_HA-3-TW_INIT_FAILED

3-Error

Firewall High availability update timer initialization failed

Firewall High Availability update timer initialization failed

ios-firewall

"Firewall HA update timer initialization failed under unsual circumstances \n\ Check the available memory and CPU utilization on the router and verify \n\ that it satisfies the requirements for the feature \n\ If the requirement are satisfied collect the output of show tac and \n\ report it to Cisco Technical assistance centre."

FW_HA-3-RF_REG_FAILED

3-Error

Firewall High availability registration to RF failed

Firewall High Availability could not register as a Redundancy Facility\n\ client

ios-firewall

"Firewall HA subsys registration as Redundancy Facility client failed \n\ verify if this image is capable of doing Box-Box redundancy. \n\ Collect the image version information and report the probelm to\n\ Cisco Technical assistance centre"

FW_HA-3-CF_REG_FAILED

3-Error

Firewall High availability registration to CF failed

Firewall High Availability could not register as a Checkpoint Facility\n\ client

ios-firewall

"Firewall HA subsys registration as Checkpoint Facility client failed \n\ verify if this image is capable of doing Box-Box redundancy. \n\ Collect the image version information and report the probelm to\n\ Cisco Technical assistance centre"

FW_HA-6-NO_INSPECT_RULE_ON_STDBY

6-Information

Firewall High availability - inspect rule is not configured on standby for interface [chars] dir in/out

NO inspect rule on standby is configured on same interface and inspect\n\ dir configured on active

ios-firewall

"Please check firewall configuration on standby and make sure it should \n\ be same with active's configuration"

FW_HA-6-NO_HSRP_GNAME_ON_STDBY

6-Information

Firewall High availability - Inpsect redundancy group is not configured on standby for interface [chars] dir in/out

NO hsrp group name on standby is configured on same interface and\n\ inspect dir configured on active

ios-firewall

"Please check firewall configuration on standby and make sure it \n\ is same with active's configuration"

FW_HA-6-PROT_MISMATCH

6-Information

Firewall High availability - L4/L7 protocol mismatch between active and standby

Firewall High Availability configuration of inspect rule or hsrp group \n\ name does not match between the Active and Standby devices

ios-firewall

"Firewall High Availability configuration between the Active and Standby\n\ devices are not automatically synched. Check to see if the configuration\n\ of the Active and Standby are in synch. Check the configuration guidelines\n\ for all areas that should match."

FW_HA-6-AUDIT_TRAIL_STDBY_START

6-Information

[chars]Start [chars] standby session: initiator [inet]:[dec] -- responder [inet]:[dec]

This message documents the opening of an inspection session on \n\ standby router. The message is issued at the start of each\n\ inspected session and it records the source/destination\n\ addresses and ports.

ios-firewall

"This message is for informational purposed only and can be used\n\ to collect the basic accounting for inspected sessions."

FW_HA-6-AUDIT_TRAIL_STDBY_STOP

6-Information

[chars]Stop [chars] standby session: initiator [inet]:[dec] -- responder [inet]:[dec]

This message documents the deletion of an inspection session on\n\ standby router. The message is issued at the end of each\n\ inspected session and it records the source/destination\n\ addresses and ports.

ios-firewall

"This message is for informational purposed only and can be used\n\ to collect the basic accounting for inspected sessions."

FW_HA-6-AUDIT_TRAIL_STDBY_TO_ACT

6-Information

Sessions matching HSRP group [chars] are being transitioned from Standby to Active state

This message documents sessions on standby router that\n\ match this hsrp group name are changed to active. The message\n\ is issued when the standby router becomes active

ios-firewall

"This message is for informational purposed only and can be used\n\ to collect the basic accounting for inspected sessions."

CBAC_C3PL-4-OBJ_CREATE

4-Warning

Firewall [chars] object [chars] creation failed in the data plane error [dec]

The notification of the creation of a firewall object e.g. a parameter\n\ map has failed to update the data plane and as such the application\n\ of the parameters contained within the object will not be applied to\n\ the data plane. It is also possible that the common classification\n\ may fail to locate and bind to the object rendering the configuration\n\ incomplete in terms of application.

inspect

show memory

CBAC_C3PL-4-OBJ_DELETE

4-Warning

Firewall [chars] object [chars] deletion failed in the data plane error [dec]

The notification of the deletion of a firewall object e.g. a parameter\n\ map has failed to update the data plane and as such the application\n\ of the parameters contained within the object may continue to be\n\ applied to the data plane.

inspect

show memory

CBAC_C3PL-4-OBJ_MODIFY

4-Warning

Firewall [chars] object [chars] modification failed in the data plane error [dec]

The notification of the modification of a firewall object e.g. a\n\ parameter map has failed to update the data plane and as such the\n\ application of the parameters contained within the object will not be\n\ applied to the data plane.

inspect

show memory

CBAC_C3PL-3-INIT

3-Error

Firewall data plane updates are disabled

The firewall notification of objects to the data plane has failed to\n\ startup and as such data plane updates are disabled.

inspect

show registry brief

IPAD-3-LISTTYPE

3-Error

Double-linked list DLL type not recognized: [dec].

An internal IPAD error occurred. DLL type not defined.

ip

""

IPAD-3-CTXTMASKTYPE

3-Error

Search context mask type or sub type not recognized: [dec] [dec]. Search\n\ context last found IP address [inet] search context target IP address [inet].

An internal IPAD error occurred. Search contex mask type not defined.

ip

""

IPAD-3-BLOCKEMPTY

3-Error

Block does not exist.

Try to access a block that does not exist.

ip

""

IPAD-3-TRIM

3-Error

Access on level [dec] to the left of index [dec].

IPAD is not trimmed properly.

ip

""

IPAD-3-MEMORY

3-Error

Can not allocate memory for a block in IPAD: [chars]

The operation may have failed due to lack of memory.

ip

""

IPACCESS-2-NOMEMORY

2-Critical

Alloc fail for acl-config buffer. Disabling distributed mode on lc

Unable to malloc a buffer to send access-list configuration down\n\ to linecards.

ip-acl

"Enter a show chunks command and report the output along with this\n\ error message to your technical support representative."

IPACCESS-2-WRONGREQUEST

2-Critical

Invalid request to allocate chunk of size [dec]

We only allow acl chunks of max size IPACCESS_LARGE_CHUNK_SZ

ip-acl

" "

IPACCESS-2-WRONGSIZE

2-Critical

Incorrect length acl ipc xdr of type=[chars] len=[dec] received

Received an acl message of the wrong size for that type

ip-acl

"Report this error message to your tech support representative."

IPACCESS-4-INVALIDACL

4-Warning

Invalid ACL field: [chars] is [dec]

An internal software error occurred.

ip-acl

"Copy the message exactly as it appears and report it to your\n\ technical support representative."

IPACCESS-3-SANITY_ERROR

3-Error

[chars]

A sanity error occurred while the ACL was being configured on the RP or while the ACL configuration was being downloaded to the line card.

ip-acl

LOG_STD_ACTION

IPACCESS-3-XDRREGISTRATION

3-Error

Failed to register [chars] XDR client due to [chars]

Failure to register the said XDR client.

ip-acl

"Copy the message exactly as it appears and report it to your " "technical support representative."

IPNAT_HA-3-MISMATCH

3-Error

[chars] [chars] mismatch with id [dec]

The specified synchronization operation has failed to complete on the\n\ standby route processor due to an inconsistency in the internal id\n\ which would have resulted in an inconsistent configuration between\n\ active and standby. The resultant action taken by the standby route\n\ processor is an attempt to resynchronize.

nat

LOG_STD_ACTION

IPNAT_HA-6-MAPPING_EXISTS

6-Information

[chars] [chars] [chars] mapping id [dec]

The specified synchronization operation on the standby route processor\n\ has detected the presence of an existing matching mapping. This may\n\ be associated with any observed PRC failures on the standby.

nat

LOG_STD_ACTION

IPNAT_HA-6-MAPPING_COMPARE

6-Information

[chars] [chars] [chars] mapping id [dec] comparing [chars] [chars] [chars] mapping id [dec]

The specified synchronization operation on the standby route processor\n\ has detected an internal condition with respect to the properities of\n\ dynamic mappings. This is informational.

nat

LOG_STD_ACTION

IPNAT_HA-3-TRANSFORM

3-Error

[chars] of [chars] via [chars] failed [chars]

An attempt to either encode or decode a versioned synchronization\n\ message has failed due to an internal error encountered by the ISSU\n\ component.

nat

LOG_STD_ACTION

IPNAT_HA-3-RECEIVE

3-Error

Message via [chars] is [chars]

An ISSU registration for the set of initial capabilities and sessions\n\ failed due to the reason specified. This will have the effect of the\n\ NAT ISSU support being unavailable between peers.

nat

LOG_STD_ACTION

IPNAT_HA-3-DECODE

3-Error

Decode via [chars] of [chars] failed

A message of the transport and type described failed in its attempt\n\ to be decoded on the standby. The resultant action taken by the\n\ standby route processor is an attempt to resynchronize.

nat

LOG_STD_ACTION

IPNAT_HA-3-BULK_SYNC

3-Error

Failed to send [chars] information to peer

-

nat

LOG_STD_ACTION

IPNAT_HA-3-DYN_SYNC

3-Error

Failed to process [chars] dynamic state

The incremental synchronization of the NAT configuration to the standby\n\ RP has failed to complete successfully. This implies that the\n\ configuration state between the active and standby RP is\n\ inconsistent.

nat

"show ip nat ha"

IPNAT_HA-3-DYN_DEFERQ

3-Error

[chars] failed to defer[chars]

The incremental synchronization of the NAT dynamic state to the standby\n\ RP has failed to add the information to the deferral queue for later\n\ processing during the time where the standby RP is progressing to it's\n\ hot standby redundant state. This implies that the runtime state\n\ between the active and standby RP would be inconsistent once the\n\ standby has been fully initialized.

nat

"show ip nat ha"

IPNAT_HA-6-TIMEOUT

6-Information

Bulk sync is flow controlled by [chars]

The bulk synchronization of the NAT configuration to the standby RP\n\ has encountered a flow control condition which has effected a timeout\n\ awaiting the condition to clear. This will result in a reload of the\n\ standby RP to allow the bulk synchronization to restart.

nat

LOG_STD_ACTION

IPNAT_HA-3-CLIENT

3-Error

Failed to register with [chars] [chars]

The NAT High Availability has failed to register with the specified\n\ component during initialization. This is an internal error which\n\ indicates that the NAT HA services will be unavailable.

nat

LOG_STD_ACTION

IPNAT_HA-6-READY

6-Information

[chars] peer not ready discarding [chars]

The synchronization attempt for the message has determined that the\n\ transport has lost communication with its peer. This is a normal\n\ situation which indicates that the standby route-processor is currently\n\ out of service implying a simplex redundancy mode.

-

-

IPNAT_HA-6-RELOAD

6-Information

[chars] reloading [chars]

A synchronization attempt between the active and standby RP peers has\n\ failed with the reason indicated. The standby peer is reloaded in an\n\ attempt to resynchronize when operating in a stateful redundant\n\ mode.

nat

LOG_STD_ACTION

IPNAT_HA-6-RELOAD_DISABLED

6-Information

Standby reload has been disabled NAT RP state is out of sync and the standby should be reloaded manually

The active and standby RPs are out of sync and the standby RP would have been reloaded but this reload was suppressed based on the configured environment.

nat

LOG_STD_ACTION

IPNAT_HA-3-ATTRIBUTE

3-Error

Bulk sync of [chars] via [chars] [chars] is invalid for [chars]

An attempt to bulk sync an address pool or a dynamic/static\n\ translation has detected that the entity which is to be sent to the\n\ standby RP when acting in a stateful redundant mode contains an\n\ invalid owner property and hence cannot be synchronized. The detection\n\ of this case will result in a failure of the bulk sync.

nat

LOG_STD_ACTION

IPNAT_HA-3-PURGE

3-Error

Failed to purge [chars] information

-

nat

LOG_STD_ACTION

IPNAT_HA-6-INTERFACE

6-Information

[chars] type/slot %lx uint %lu num %lu channel %lu

An attempt to sync a dynamic translation or address change has\n\ detected that the interface which was encoded on the active RP\n\ is not present on the standby RP. The detection of this case\n\ may result in a failure of the bulk or LBL sync.

nat

LOG_STD_ACTION

IPNAT_HA-3-INTERFACE_TYPE

3-Error

[chars] type/slot %lx unit %lu num %lu channel %lu value [dec]

An attempt to sync a dynamic translation or address change has\n\ detected that the interface which was encoded on the active RP\n\ has a different type the standby RP. The detection of this\n\ case will result in a failure of the bulk or LBL sync.

nat

LOG_STD_ACTION

IPNAT_HA-6-ADDR_CHANGE

6-Information

[chars] unable to encode data descriptor for interface [chars]

An attempt to sync an address change to the standby RP has\n\ detected that the interface which was to be encoded on the\n\ active RP is no longer present or does not support encoding. \n\ The interface may have been removed from the configuration or \n\ may not support encoding.

-

LOG_STD_ACTION

RITE-5-ACTIVATE

5-Notice

Activated IP traffic export on interface [chars]

IP traffic export has been enabled on the specified interface

-

"None"

RITE-5-DEACTIVATE

5-Notice

Deactivated IP traffic export on interface [chars]

IP traffic export has been disabled on the specified interface

-

"None"

RITE-5-MODIFIED

5-Notice

Changed IP traffic export outbound interface from [chars] to [chars]

The outbound interface for IP traffic export has been changed

-

"None"

PLATFORM_CAPABILITY-4-INIT

4-Warning

Fatal Initialization Error - [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

PLATFORM_CAPABILITY-4-CALL

4-Warning

Fatal Initialization Error - [chars]

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

IP_VFR-4-TINY_FRAGMENTS

4-Warning

[chars]: from the host [inet] destined to [inet]

This message indicates that the router is receiving tiny fragments - meaning the initial fragment does not have complete layer 4 header

ios-firewall

"This is an informational message"

IP_VFR-3-OVERLAP_FRAGMENTS

3-Error

[chars]: from the host [inet] destined to [inet]

This message is logged whenever the router encounters overlap fragments. Overlap fragment means offset of one fragment overlaps the offset of another fragment. For example if first fragment's offset is 0 and length is 800 then the second fragments offset must be 800. If second fragment's offset is less than 800 that means the second fragment overlaps the first fragment.

ios-firewall

"This could possibly be an attack configure a static ACL to prevent " "further overlap fragments from the sender"

IP_VFR-4-FRAG_TABLE_OVERFLOW

4-Warning

[chars]: the fragment table has reached its maximum threshold [dec]

This means the number of datagrams reassembled at a time reached its maximum limit increase the value of max-reassemblies using ip virtual-reassembly max-reassemblies <number>

ios-firewall

-

IP_VFR-4-TOO_MANY_FRAGMENTS

4-Warning

[chars]: Too many fragments per datagram more than [dec] - sent by [inet]

This message indicates the datagram being reassembled has received more fragments than its threshold value

ios-firewall

"Check if the fragments received are from a genuine source if so " "increase the value of max-fragments using the CLI " "ip virtual-reassembly max-fragments <number>"

IP_VFR-3-INVALID_FRAG_LENGTH

3-Error

[chars]: fragment length invalid - received from [inet] destined to [inet]

This message indicates that the router has encountered a ping-of-death sort of an attack

ios-firewall

"To prevent further attacks its highly recommendated that an ACL " "be configured to drop any traffic from the sender"

IP_VFR-3-SYSTEM_ERROR

3-Error

[chars]: IP VFR System failure - [chars]

This message indicates the misc errors in the VFR subsystem

ios-firewall

-

MTRIE-4-MTRIECORRUPTLEAF

4-Warning

[inet]/[dec] - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

MTRIE-4-MTRIELEAFOPFAIL

4-Warning

[inet]/[dec] - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

MTRIE-4-PLACEALLOC

4-Warning

Failed to allocate place holder

An internal software error occurred.

-

LOG_STD_ACTION

MTRIE-4-MTRIEMISALIGNEDNODEPTR

4-Warning

0x[hec] - [chars]

An internal software error occurred.

-

LOG_STD_ACTION

IPFAST-2-RADIXINIT

2-Critical

Error initializing IP fast cache structures

A programming error occurred.

-

LOG_STD_SH_TECH_ACTION

IPFAST-2-IPCACHEINIT

2-Critical

Error initializing IP fast cache structures

A programming error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IPFAST-2-MSGDROP

2-Critical

IPC queue limit is reached and message is dropped. queue limit = [dec] cumulative drops = [dec]

IPC raw queue limit for IP fast path is reached.

-

LOG_STD_ACTION

IPFAST-6-PAKSHORT

6-Information

Packet too short from [inet] datagram size [dec] tl [dec]

An IP packet which is too short was received

-

LOG_STD_NO_ACTION

IPFAST-2-INVALSIZE

2-Critical

The IP fast path received an IPC message with an invalid sizesize/type - [dec]/[dec]

-

-

-

IPFAST-2-FAILOPENIPCPORT

2-Critical

Could not open the IPC ports. [chars]

ipfast could not open the ipc port to communicate to the LC/RRP/SP.

-

LOG_STD_SH_TECH_ACTION

COMPILED_ACL-3-INTERNAL_ERROR

3-Error

an unexpected internal error occured: [chars]

An unexpected internal error occurred. This error may result in one or more flows being punted to the RP or in Turbo ACL not functioning.

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-BACKPOINTER_WRONG

4-Warning

[chars]: entry at row [dec] column [dec] in node [dec] does not reference row [dec] in the node's child

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-BACKPOINTER_PROCESSING_OVERFLOWED

4-Warning

[chars]: processing back-pointers in row [dec] in node [dec] but the list is marked as overflowed

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-BACKPOINTER_OVERFLOWED_NOT_EMPTY

4-Warning

[chars]: the back-pointer list for row [dec] in node [dec] is marked as overflowed but is not empty

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-BACKPOINTER_OVERFLOWED_NOT_EMPTY_REFERENCES

4-Warning

[chars]: the back-pointer list for row [dec] in node [dec] is marked as overflowed but is not empty

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-BAD_PROCESS_REFERENCES

4-Warning

[chars]: error while processing references for row [dec] in node [dec]: [chars]

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-DEFERRED_ENTRY_CONSISTENCY

4-Warning

[chars]: while [chars] in row [dec] in node [dec] found deferred entry bitmap is [chars] but count is [dec]

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-ROW_UPDATE

4-Warning

[chars]: cannot process row queue update for row [dec] in node [dec]: [chars]

EXPLANATION_INTERNAL_ERROR EXPLANATION_IMPACT_POSSIBLE_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-ROW_UPDATE_ENQUEUE

4-Warning

[chars]: cannot process row queue update for row [dec] in node [dec]: enqueue failed %lu/%lu entries list is [chars]valid entry is [chars]enqueued

-

-

-

COMPILED_ACL-2-LIST_CREATE

2-Critical

[chars]: failed to create row queue for node [dec] Turbo ACL has been disabled temporarily

The system encountered an error while initializing a data structure required for the correct operation of Turbo ACL processing. Turbo ACL will be disabled until another recompilation has completed successfully.

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-2-QUEUE_INIT

2-Critical

[chars]: failed to initialize back-pointer list for row [dec] in node [dec] Turbo ACL has been disabled temporarily

The system encountered an error while initializing a data structure required for the correct operation of Turbo ACL processing. Turbo ACL will be disabled until another recompilation has completed successfully.

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-5-LIST_INFO

5-Notice

[chars]: failed to set list information function for node [dec]'s row queue ID [dec]

The system encountered an error while initializing a function vector used for debugging purposes. Turbo ACL will continue to function correctly but the <CmdBold>show list<NoCmdBold> <CmdArg>ID<NoCmdArg> command will not show Turbo ACL-specific information for the specified list ID number.

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-BAD_ROW_FREE

4-Warning

[chars]: cannot free row [dec] in node [dec]: [chars]

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

COMPILED_ACL-4-ENTRY_COUNT

4-Warning

[chars]: row entry counters not allocated for node [dec] while freeing row [dec]

EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING

c7300-pxf

RECOMMENDED_ACTION

IPFLOW-2-QUEUEINIT

2-Critical

Error initializing Flow feature queue

Initialization of the Flow feature queue could not be accomplished because of a low memory condition.

netflow-switch

"Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

IPFLOW-3-DISABLEFLOWEXPORT

3-Error

NULL

Flow export is disabled because export destination address matches with one of the interface's IP addresses

netflow-switch

"IP addresses of all the interfaces must be checked to make sure none \n\ of them matches with flow export destination IP address."

IPFLOW-2-PROCESSINIT

2-Critical

Error initializing Flow background process

Initialization of the Flow background process could not be accomplished because of a low memory condition.

netflow-switch

"Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

IPFLOW-2-CACHEINIT

2-Critical

Error initializing IP flow cache

Initialization of the Flow cache could not be accomplished because of \n\ a low memory condition.

netflow-switch

LOG_STD_SH_TECH_ACTION

IPFLOW-2-EXPORTINIT

2-Critical

Error initializing Flow Export queue

Initialization of the Flow export queue could not be accomplished \n\ because of a low memory condition.

netflow-switch

"Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

IPFLOW-2-TEMPLATETBL_INIT

2-Critical

Error initializing Flow Export Template Table

Initialization of the Flow export template table could not be \n\ accomplished because of a low memory condition.

netflow-switch

"Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

IPFLOW-4-V9_TEMPLATE_EXPORT

4-Warning

Error creating [chars]

Version 9 export template length is zero

netflow-switch

LOG_STD_DBG_ACTION

IPFLOW-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

netflow-switch

-

NATMIB_HELPER-3-NOCREAT

3-Error

NATMIB Helper Process not created - NAT MIB will not work properly

Attempt to start NATMIB Helper Process failed when\n\the natmib subsystem was initialised.

snmp

"The NATMIB Helper process was not\n\createdpossibly due to lack of memory. If you want to use the NATMIB \n\reconfigure the box so that less memory is used by\n\other features or add more memory to the system. Reload the box\n\after reconfiguring."

IP_SNMP-3-SOCKET

3-Error

can't open UDP socket

The SNMP server was unable to open a port for receiving or\n\ transmitting SNMP requests. This usually happens when the SNMP\n\ server is started using the snmp-server community configuration\n\ command on a router or communication server with an interface that\n\ has no IP address configured. Another possible cause is low memory.

-

"Configure at least one interface with an IP address or specify the no\n\ snmp-server command to remove the SNMP server process. Call your\n\ technical support representative if problems persist or if it becomes\n\ necessary to add memory."

IP_SNMP-4-NOTRAPIP

4-Warning

SNMP trap source [chars] has no ip address

The user entered an snmp-server trap-source command. The interface\n\ requested for use as the source address has no ipv4 address\n\ associated with it. The SNMP trap is being sent anyway but\n\ without the source address that the user intended.

-

"There are two possible solutions. Either enter a no snmp-server\n\ trap-source command to disable the request for a specific source IP\n\ address or add an IP address to the interface referenced in the\n\ snmp-server trap-source configuration command."

IP_SNMP-4-NOTRAPIPV6

4-Warning

SNMP trap source [chars] has no ipv6 address

The user entered an snmp-server trap-source command. The\n\ interface requested for use as the source address has no ipv6\n\ address associated with it. The SNMP trap is being sent\n\ anyway but without the source address that the user intended.

-

"There are two possible solutions. Either enter a no snmp-server\n\ trap-source command to disable the request for a specific source\n\ IP address or add an IPV6 address to the interface referenced\n\ in the snmp-server trap-source configuration command."

IP_SNMP-4-TOOBIG

4-Warning

Oversize message from [inet] datagram size [dec] udp length [dec]

An incoming SNMP packet had a length field so large that\n\ the system had to assume it was in error. This system made a\n\ correct reaction to bad external data.\n\ Since SNMP packets should originate from systems under the\n\ same administration this may indicate that the network host\n\ used to originate the SNMP request had a problem in its\n\ networking layer.\n\ Alternatively if the SNMP packet originated from outside\n\ the local administrative domain it could indicate an\n\ failed attempt at security penetration and that site should\n\ be watched more closely.

-

"If the origin is local no action is required.\n\ If the origin is determined to be malicious either contact the\n\ administrator of the originating site or install filters to\n\ prevent access by that site as circumstances warrant."

REMIF-3-INITSYS

3-Error

[chars]

Failed to create remif_udp_process

-

""

REMIF-3-NOMEM

3-Error

No available memory for [chars]

-

-

""

REMIF-3-NOSOCKET

3-Error

Unable to open UDP input socket

The requested operation could not be accomplished because of a possible low memory condition.

-

-

REMIF-3-BADCMD

3-Error

[dec] from [inet]

-

-

""

REMIF-3-OQUEUE

3-Error

output on [chars]

-

-

""

REMIF-3-IQUEUE

3-Error

input on [chars]

-

-

""

REMIF-3-IFNONE

3-Error

[chars] does not exist. Requested by [chars]

-

-

""

REMIF-3-TCPERR

3-Error

TCP error status [dec]

-

-

""

REMIF-3-DUPOPEN

3-Error

[chars] is already open by [chars]

-

-

""

REMIF-3-OPEN

3-Error

[chars] now owns [chars]

-

-

""

REMIF-3-CLOSED

3-Error

[chars] has released [chars]

-

-

""

IPNAT-4-ADDR_ALLOC_FAILURE

4-Warning

Address allocation failed for [inet] pool [chars] might be exhausted

An address could not be allocated from the IP NAT pool. This condition can cause a translation failure and might result in packets being dropped. The counter for misses will be incremented for these packets.

nat

"Check to see if the NAT pool has been exhausted. To reuse any existing " "addresses in the NAT pool for new packet flows clear the current NAT " "entries using clear ip nat translation *"

IPNAT-3-SYSSTATSNULL

3-Error

NAT global/system statistics structure from platform is nul

The structure for passing global/systems statistics from platform \n\ is nul which is invalid. This condition can cause the NAT global\n\ statistic counters in inaccurate on the RP

nat

LOG_STD_ACTION

IPNAT-3-POOLSTATSNULL

3-Error

NAT pool statistics structure from platform is nul

The structure for passing global/systems stats from platform \n\ is nul which is invalid. This condition can cause the statistic\n\ counters for NAT pool to be inaccurate on the RP

nat

LOG_STD_ACTION

IPNAT-3-BADMAPPINGTYPE

3-Error

NAT mapping type [dec] for mapping statistics from platform is \n\ invalid

The mapping type for passing mapping statistics from platform is \n\ not for static nor dynamic mapping type which is invalid. This \n\ condition can cause the statistic counters for NAT mapping to be\n\ inaccurate on the RP

nat

LOG_STD_ACTION

IPNAT-3-MAPPINGSTATSNULL

3-Error

NAT mapping statistics structure from platform is nul

The structure for passing mapping statistics from platform is \n\ nul which is invalid. This condition can cause the statistic\n\ counters for NAT mapping to be inaccurate on the RP

nat

LOG_STD_ACTION

IPNAT-3-LIMITSTATSNULL

3-Error

NAT mexentry statistics structure from platform is nul

The structure for passing maxentry limit statistics from platform is \n\ nul which is invalid. This condition can cause the statistic\n\ counters for NAT maxentry limit to be inaccurate on the RP

nat

LOG_STD_ACTION

IPNAT-3-PORTNULL

3-Error

Start port or end port for port block allocation request is nul

Start port or end port for port block allocation request is nul\n\ This condition can cause the new translations to fail in the \n\ data path

nat

LOG_STD_ACTION

IPNAT-3-PORTLISTNULL

3-Error

Portlist for address [inet] proto [dec] is nul

The portlist for the address which requests more port blocks \n\ is nul which is invalid. This condition can cause the new \n\ translations to fail in the data path

nat

LOG_STD_ACTION

IPNAT-3-WLANSESSNULL

3-Error

NAT WLAN session structure for session [chars] from platform is nul

The structure for passing WLAN session from platform is \n\ nul which is invalid. This condition can cause the NAT WLAN\n\ session to fail in the data path

nat

LOG_STD_ACTION

IPNAT-6-ID

6-Information

[chars] identifier has wrapped

The identifier which is assigned to that which is resultant from\n\ the configuration in question has cycled through the available\n\ number space and is now allocating from its initial value again.

nat

LOG_STD_NO_ACTION

IPNAT-3-RTMAPNULL

3-Error

route-map for configuration download is nul

The route-map structure is nul which is invalid. This condition\n\ can cause the new translations to fail in the data path

nat

LOG_STD_ACTION

IPNAT-3-CSBNULL

3-Error

Parser structure for route-map [chars] configuration is nul

The parser structure for route-map configuraion is nul which is invalid. This condition can cause the new translations to fail in \n\ the data path

nat

LOG_STD_ACTION

IPNAT-3-RTMAPNAMENULL

3-Error

Route-map name for [chars] configuration is nul

The route-map name is nul which is invalid. This condition can cause the new translations to fail in the data path

nat

LOG_STD_ACTION

IPNAT-6-ENTRIES

6-Information

Static translation count reset inside/outside source/destination %llu/%llu %llu/%llu

Upon the removal of the last remaining static translation from the\n\ configuration it has been determined that there is a discrepancy\n\ with the internal accounting as regards the previous provisioning\n\ of inside source/destination versus outside source entries. The\n\ internal accounting has been reset to indicate that there are no\n\ translations of any type currently.

nat

LOG_STD_ACTION

IPNAT-3-CONFIG

3-Error

Unable to [chars] the configuration of dynamic mappings

An internal operation relating to the configuration of the\n\ dynamic mappings has failed. This may imply that the mapping\n\ has not been installed.

nat

LOG_STD_ACTION

IPNAT-6-PORT_ALLOC

6-Information

Port allocation via [chars] for [dec] [chars] [chars] ports min [dec] max [dec]

A port allocation request for the specified range of ports has been\n\ attempted from the named party on the standby RP. This is an\n\ informational message which tracks the request source.

nat

LOG_STD_ACTION

IPNAT-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

nat

-

IPNAT-3-IF_UP

3-Error

Error in sending interface UP event for [chars] to the ager process

An internal operation relating to the interface UP event\n\ has failed which is unexpected.

nat

LOG_STD_ACTION

IPNAT-3-UNEXPECTED_MAPPING_FLAG

3-Error

Unexpected mapping flag %#04x received

An internal operation relating to notifying the platform about a\n\ mapping has provided an unexpected input.

nat

LOG_STD_ACTION

IPNAT-3-MAPPING_NULL

3-Error

Unexpected NULL pointer received as input.

An internal operation relating to notifying the platform about a\n\ mapping has provided an unexpected input.

nat

LOG_STD_ACTION

IPNAT-3-CENTRAL_POLICY

3-Error

Central policy setting failed: [chars]

Central policy setting can not be changed due to incompatible configuration.

nat

"Remove existing NAT routes and mappings."

IPNAT-3-UNEXPECTED_ADDRESS

3-Error

NULL

An address contained an unexpected value.

nat

LOG_STD_ACTION

SEC-4-TOOMANY

4-Warning

Box secured too many options on internal packet

No room for all desired IP header options. Packet discarded.

-

"Configure for fewer IP header options."

SEC-2-NOOPT

2-Critical

Box secured no option on internal packet

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SEC-2-NOTSEC

2-Critical

First opt in tcb not BASIC security

An internal software error occurred.

-

"If this message recurs contact your technical support\n\ representative."

SEC-2-SECINS

2-Critical

Security opt in tcb not SECINSERT

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SEC-3-NOMAX

3-Error

No default for NLESO defined

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

SEC-6-IPACCESSLOGNP

6-Information

list [chars] [chars] [dec] [inet] [chars]-> [inet] %llu packet[chars] [chars]

A packet matching the log criteria for the given access list was\n\ detected.

-

LOG_STD_NO_ACTION

SEC-6-IPACCESSLOGDP

6-Information

list [chars] [chars] [chars] [inet] [chars]-> [inet] [dec]/[dec] %llu packet[chars] [chars]

A packet matching the log criteria for the given access list was\n\ detected.

-

LOG_STD_NO_ACTION

SEC-6-IPACCESSLOGP

6-Information

list [chars] [chars] [chars] [inet][dec] [chars]-> [inet][dec] %llu packet[chars] [chars]

A packet matching the log criteria for the given access list was\n\ detected.

-

LOG_STD_NO_ACTION

SEC-6-IPACCESSLOGRP

6-Information

list [chars] [chars] [chars] [inet] [chars]-> [inet] %llu packet[chars] [chars]

A packet matching the log criteria for the given access list was\n\detected.

-

LOG_STD_NO_ACTION

SEC-6-IPACCESSLOGS

6-Information

list [chars] [chars] [inet] %llu packet[chars] [chars]

A packet matching the log criteria for the given access list was\n\ detected.

-

LOG_STD_NO_ACTION

SEC-6-IPACCESSLOGRL

6-Information

access-list logging rate-limited or missed [dec] packet[chars]

Some packet matching logs were missed because the access list log \n\messages were rate-limited or no access list log buffers were available.

-

LOG_STD_NO_ACTION

SEC-4-SHELFCTLRTELOPT

4-Warning

malformed option on vty[t-line] [chars][chars][chars][dec] len [dec] [chars]

A packet containing shelf controller telnet options was malformed. Options were ignored or truncated.

-

LOG_STD_NO_ACTION

IPACCESS-3-ACL_LIMIT_EXCEEDED

3-Error

Exceeding max acl limit[dec] configurable failed to create ACL

-

-

-

IPACCESS-3-ACL_ACE_LIMIT_EXCEEDED

3-Error

Exceeding the max aces[dec] per ACL configurable

Error is occurred when aces limit per ACL is exceeding the ACL ace limit set.

ip-acl

LOG_STD_ACTION

IPACCESS-3-GLOBAL_ACE_LIMIT_EXCEEDED

3-Error

Exceeding the global max ace limit configurable[dec]

Error is occurred when the global ace limit is exceeded than the global ace limit set.

ip-acl

LOG_STD_ACTION

IP-4-CLASS

4-Warning

Bad IP address and mask [inet]%m in class_resolve

An internal software error occurred.

-

LOG_STD_RECUR_ACTION

IP-4-DUPADDR

4-Warning

Duplicate address [inet] on [chars] sourced by [enet]

Another system is using your IP address.

-

"Change the IP address of one of the two systems."

IP-4-ZERO_ADDR

4-Warning

Zero MAC address for [inet] in ARP cache

An entry in the ARP cache have a NULL MAC address

-

"If this message recurs call your technical support\n\ representative for assistance."

IP-3-DESTHOST

3-Error

src=[inet] dst=[inet] NULL desthost

An internal software error occurred.

-

LOG_STD_ACTION

IP-3-BADIPALIGN

3-Error

Invalid alignment in packet for IP. [chars]=[hex]

The packet data structure is misaligned. This condition may result in\n\ a small amount of overhead in processing IP traffic.

-

"Enter a show hardware command and report the output along with this\n\ error message to your technical support representative."

IP-3-BADSROUTE

3-Error

Improper source route. Length [dec] Ptr [dec]

A hardware or software error occurred.

-

LOG_STD_ACTION

IP-6-PHYBCASTDROP

6-Information

Physical broadcast packet detected and dropped src=[inet] dst=[inet]

Physical broadcast packet was dropped.

ip

LOG_STD_NO_ACTION

IP-6-L2MCASTDROP

6-Information

Layer 2 Multicast packet detected and dropped src=[inet] dst=[inet]

Layer 2 Multicast packet with Layer3 Unicast Destination was dropped.

ip

LOG_STD_NO_ACTION

IP-3-LOOPPAK

3-Error

Looping packet detected and dropped - \nsrc=[inet] dst=[inet] hl=[dec] tl=[dec] prot=[dec] sport=[dec] dport=[dec] \nin=[chars] nexthop=[inet] out=[chars]\noptions=[chars]

A software error occurred.

-

LOG_STD_ACTION

IP-5-WEBINST_START

5-Notice

Attempting web install from host [inet]

A hardware or software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IP-5-WEBINST_KILL

5-Notice

Terminating DNS process

A hardware or software error occurred.

-

LOG_STD_ACTION

IP-5-WEBINST_COMP

5-Notice

Selected IP address [inet]

A hardware or software error occurred.

-

LOG_STD_ACTION

IP-5-WEBINST_RESP

5-Notice

Sending DNS response to [inet] request was for [inet]

-

-

-

IP-3-CNTRFULL

3-Error

IP counter block is full setting protocol [dec]

An internal software error occured.

-

LOG_STD_SH_TECH_ACTION

IP-5-TURBOACL

5-Notice

[chars]

Error occured in intialisation of TURBOACL.

-

show process

IP-5-ACL

5-Notice

[chars]

Error occured in IP access checks.

-

LOG_STD_SH_TECH_ACTION

IP-4-UNICASTRPF

4-Warning

IP unicast reverse-path check disabled on [chars]

The IP verify unicast reverse-path feature was disabled because CEF was disabled either through configuration or due to an internal error.

-

LOG_STD_SH_TECH_ACTION

IP-3-LOOPOUTIF

3-Error

Output interface for packet has been changed for [dec] times and dropped - \nsrc=[inet] dst=[inet] hl=[dec] tl=[dec] prot=[dec] \nin=[chars] nexthop=[inet] out=[chars]

A software error occurred.

-

LOG_STD_ACTION

IP-3-MAXIRDP

3-Error

Attempt to send IRDP to proxies exceeding configurable limit: [dec] interface: [chars] secondary = [dec] proxy = [dec]\n

The sum of configured secondary addresses and configured proxy addresses exceeds the number of total addresses that the IRDP can support in its implementation.

-

"Reduce the number of either the secondary IP addresses or proxy" " addresses configured for the interface."

IP-4-IPPOOLS

4-Warning

Detected a local pool and a DHCP pool with the same name: [chars]

A local pool and a DHCP pool have been configured with the same name. This may cause conflict during address allocations.

-

"Change the name of one of the two pools"

IP-3-ICMPRATELIMIT

3-Error

[dec] unreachables rate-limited within [dec] milliseconds on [chars]. [dec] log messages suppressed since last log message displayed on [chars]

An excessive number of packets are triggering log messages on this interface

-

"change the log threshold with the icmp rate-limit command or " "find the source of the packets and block the packets from this router"

IP-3-ICMPRATELIMITDF

3-Error

[dec] DF unreachables rate-limited within [dec] milliseconds on [chars]. [dec] DF log messages suppressed since last log message displayed on [chars]

An excessive number of packets are triggering log messages on this interface

-

"change the log threshold with the icmp rate-limit command or " "find the source of the packets and block the packets from this router"

IP-3-NOOUTINTF

3-Error

Output interface not available. source address: [inet] destination address: [inet] routing type: [dec]

The output interface for this packet is not set

ip

LOG_STD_ACTION

IP-3-NONALIAS

3-Error

non-alias address [inet] in table [chars] found in IP alias list

The IP alias list holds IP aliases only but non-alias entries are found.

ip

LOG_STD_ACTION

IP-3-IPTOPOID

3-Error

Topology ID 0x[hec] is invalid can't get the base topology ID.

An internal software error occurred

-

LOG_STD_ACTION

IP-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

ip

LOG_STD_ACTION

IPDR-2-ERROR_SOCKET

2-Critical

\n Receive a wrong socket id [dec]

The socket to close is not exist or belong to the ipdr process

cmts-application

LOG_STD_SH_TECH_ACTION

IPDR-2-GENERAL_ERR_SOCKET

2-Critical

\n [chars]

encounter some error when binding listening or receiving the event from the socket fd

cmts-application

LOG_STD_SH_TECH_ACTION

IPE-3-STATICHOST

3-Error

Failed to add [chars] entry for host [inet] of tableid [dec]

An internal software error occurred.

ipe

LOG_STD_ACTION

IPE-2-HOST_SECURITY_VIOLATION

2-Critical

Security violation occurred caused by IP address [inet] on port [chars].

An unauthorized device attempted to connect on a secure port. The IP address of the unauthorized device and the secure port are specified in the error message.

ipe

"Determine the device that attempted to connect on the secure port." "Notify your network system administrator of this condition."

IPE-4-DUPLICATE_HOST

4-Warning

Host [inet] is attached to multiple forwarders. Use \show ipe errors\ command to check for possible errors.

In a host move scenario it is possible that a host is transiently attached to multiple forwarders during IPe convergence. However it is an error if a host continues to be attached to multiple forwarders.

ipe

"Use \"show ipe errors\" command to identify the forwarders where " "the host is reported to be attached and fix the error condition."

IPE-4-DUPLICATE_LOCAL_HOST

4-Warning

Host [inet] on interface [chars] has duplicate ip address.

If existing host has been removed it is possible that this is a transient condition. An expedited ARP track is started on existing host to remove the entry if the host is no longer there. Once existing entry is removed host addition will be possible. However it is an error if multiple hosts continue to use duplicate address.

ipe

"Use \"show ip host mapping\" command to identify the interface where " "the host is reported to be attached and remove the duplicate ip " "address from one of the hosts."

IPE-3-DUPLICATE_CONFIG_MASTER

3-Error

Multiple Configuration Masters in domain [chars]. Use \show ipe errors\ command to check for errors.

There must be one Configuration Masters in every IPe domain.

ipe

"Make sure that there is only one Forwarder configured as the " "Configuration Master in a domain. Use \"show ipe errors\" " "command to identify the forwarders and fix the error condition"

IPE-3-PG_ACL_RESOURCE

3-Error

Failed to allocate an internal ACL resource needed for Policy Gateway

An attempt to allocate an internal ACL failed.

ipe

LOG_STD_ACTION

IPE-3-PG_VLAN_RESOURCE

3-Error

Failed to allocate an internal vlan resource needed for Policy Gateway

An attempt to allocate an internal vlan failed.

ipe

"Please check the config and make sure that vlan resources " "are available"

IPE-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

ipe

LOG_STD_ACTION

FS_IPHC-4-IPC_NO_CHUNK

4-Warning

IPC Chunk pool empty slot [dec] VIP junked RSP msg

IP compression private memory pool for IPC messages exhausted.

iphc

"If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative."

FS_IPHC-3-MSG_TOO_LARGE

3-Error

Received IPC message too large to handle [dec]

IP compression has received an IPC message of a size larger than expected.\n\

iphc

"If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative."

FS_IPHC-4-RP_IPCSENDFAIL

4-Warning

RP unable to send IPHC msg to LC [dec]

Route processor was unable to send an IP header compression \n\ configuration message to a line card interface.

iphc

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the <CmdBold>debug ip rtp head<NoCmdBold> and <CmdBold>debug ip tcp head<NoCmdBold>\n\ commands for the period during which this message appeared."

FS_IPHC-2-RP_NOLCINFO

2-Critical

Unable to malloc state table for LC

An internal data structure is missing due to lack of memory resources.

iphc

"The Route Processor is dangerously low on memory resources. Free up \n\ memory by removing unwanted feature configuration or upgrade the memory\n\ on the system router processor"

FS_IPHC-4-RP_NOIPCBUFFER

4-Warning

Unable to malloc IPC msg buffer [dec] on RP

Route Processor unable to send IPHC information to Line Card due to lack\n\ of memory in it's private memory pool.

iphc

"If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative."

FS_IPHC-4-LC_IPCSENDFAIL

4-Warning

LC unable to send IPHC msg to RP [dec]

Line card was unable to send an IP header compression \n\ information message to the route processor.

iphc

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the <CmdBold>debug ip rtp head<NoCmdBold> and <CmdBold>debug ip tcp head<NoCmdBold>\n\ commands for the period during which this message appeared."

FS_IPHC-2-LC_IPHC_SETUP_FAIL

2-Critical

Failed to initialise or allocate memory for IP Compression database.

IP Compression main database not created due to lack of memory resources.\n\

iphc

"The Line Card cannot allocate memory for an IP Compression database.\n\ Add more memory if possible to the VIP. \n\ Free up memory on the VIP by reducing features used or " "buffer allocations.\n\ Reduce the number of contexts configured on all interfaces on\n\ the affected line card using the interface configuration \n\ <CmdBold>ip rtp compression-connections<NoCmdBold>"

FS_IPHC-2-LC_PROC_INIT

2-Critical

LC Failed to initialise distributed IP Hdr Comp Process

IP Compression Process not created on Line Card.

iphc

"A possible reason for a process failing to start is lack of resources.\n\ Check memory allocation on line card and either upgrade line card memory\n\ or reduce feature burden in it's interface configurations."

FS_IPHC-4-LC_NOIPCBUFFER

4-Warning

Unable to malloc IPC msg buffer [dec] on line card

Line card unable to send IPHC information to Route Processor due to lack\n\ of memory in it's private memory pool.

iphc

"If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative."

FS_IPHC-3-LC_INVALID_MSG

3-Error

Received IPC message of unknown type

IP compression on Line Card has received an unknown message from Route\n\ Processor.

iphc

"If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative."

MDS-2-INIT

2-Critical

Error initializing MDS structures

An error has occurred when the system tried to initialize MDS structures

-

LOG_STD_SH_TECH_ACTION

MDS-2-RP

2-Critical

[chars]

The Route Processor either cannot allocate memeory or it has missing data

-

LOG_STD_SH_TECH_ACTION

MDS-2-RP_FAILED_IPC_CREATE

2-Critical

RP failed in creating IPC port error = [chars]

The Route Processor failed to create MDS Interprocess Communications port

-

LOG_STD_SH_TECH_ACTION

MDS-2-RP_RCV_IPC_ERR_SIZE

2-Critical

RP received oversized IPC size = [dec] type = [dec]

The Route Processor has received oversized IPC message from the linecard

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INIT

2-Critical

Error initializing linecard

System resources could not be allocated on the linecard

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_MROUTE_MSG

2-Critical

Unknown message [dec] received from RP

Unrecognized route event has been sent down from the Route Processor

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_MSG

2-Critical

Unknown IPC type [dec] received from RP

Unrecognized message type has been sent down from the Route Processor

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_SIZE

2-Critical

Invalid IPC size [dec] received from RP

Unrecognized IPC size has been sent down from the Route Processor

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_HWIDBQ_SIZE

2-Critical

Invalid Q count value

Invalid Q count value

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_SWIDBQ_SIZE

2-Critical

Invalid Q count value

Invalid Q count value

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_HWIDB_INDEX

2-Critical

Invalid if_index for HWIDB [chars]

Invalid if_index for HWIDB

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_INPUT_IF_INDEX

2-Critical

Invalid input if_index 0x[hec] for HWIDB [chars]

The input hardware IDB interface index is invalid

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_SWIDB_IFNUM

2-Critical

Invalid if_num for SWIDB [chars]

Invalid if_num for SWIDB

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_INVALID_INPUT_IFNUM

2-Critical

Invalid input if_num 0x[hec] for SWIDB [chars]

The input software IDB interface number is invalid

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_NOIPCBUFFR

2-Critical

No IPC buffers available for messages to be sent to the RP

The system has run out of buffers for IPC

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_SPDLISTCORR

2-Critical

SPD list corrupted

The list of Selective Packet Discard is corrupted

-

LOG_STD_SH_TECH_ACTION

MDS-4-ROUTELIMIT

4-Warning

Current count of [dec] exceeds multicast route-limit of [dec]

The number of multicast routes exceeds the configured maximum allowed. New routes cannot be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried by this router then use the 'ip multicast route-limit' command to increase the number of multicast routes. Otherwise no action is required."

MDS-4-ROUTELIMIT_ATTEMPT

4-Warning

Attempt to exceed multicast route-limit of [dec]

The number of multicast routes equals the configured maximum allowed. New routes cannot be added unless the configuration is changed.

-

"If multicast traffic is of any priority among the traffic carried by this router then use the 'ip multicast route-limit' command to increase the number of multicast routes. Otherwise no action is required."

MDS-3-ROUTECOUNT_ZERO

3-Error

Multicast route count reached zero

The running count of multicast routes reached zero when it should be non-zero.

-

"An error in maintaining the multicast route count has occurred." LOG_STD_ACTION

MDS-2-LC_FAILED_IPC_OPEN

2-Critical

LC in slot [dec] failed to open IPC port to RP error = [chars]

The linecard has failed to open IPC port towards the Route Processor

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_FAILED_SEND_LC_READY

2-Critical

LC in slot [dec] failed to send LC ready to RP error = [chars]

The linecard has failed to send Ready message to the Route Processor

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_FAILED_IPC_ACK

2-Critical

RP failed in getting Ack for IPC message of size [dec] to LC in slot [dec] with sequence [dec] error = [chars]

The Route Processor has failed in getting IPC acknowledgement

-

LOG_STD_SH_TECH_ACTION

MDS-2-LC_SWIDB_UPDATE_NULL_MVRF

2-Critical

LC received swidb update for if_number [hec] [chars] tableid [hec].

The linecard received a software IDB update from the Route Processor specifying a multicast VRF table ID for which no multicast VRF exists in the linecard.

-

LOG_STD_SH_TECH_ACTION

MLSM-2-IPC_ERROR

2-Critical

MMLS: IPC failure detected between RP and SP

This can happen when EOBC channel is too busy or NMP is too busy so that draco side does not get response even after few retries by IPC layer.

cat6000

"Under some stressful condition when communication between RP and SP side can not be maintained this message will be printed. MMLS will keep trying to recover from situation by sending message to SP. The restart message to SP has exponential back off upto 160 second"

MLSM-6-SCP_ERROR

6-Information

MMLS: SCP failure detected between RP and SP

This can happen when EOBC channel is too busy or NMP is too busy so that draco side does not get response even after few retries by ICC layer.

cat6000

"Under some stressful condition when communication between RP and SP side can not be maintained this message will be printed. MMLS will keep trying to recover from situation by sending message to SP. The restart message to SP has exponential back off upto 160 second"

MLSM-6-ERROR_RECOVERED

6-Information

MMLS: Communication channel between RP and SP recovered from failure

Communication between RP and SP recovered from earlier IPC / SCP failure. MMLS will install HW switched entries on backoff timer expiration. The backoff time is min10 sec * # of times error occurred^2 160

cat6000

"Note the difference between the time the error occurred to the current message. It indicates the time when no HW switched entries existed in the switch"

MLSM-6-MFD_COUNT_ERR

6-Information

MFD Count error : [inet][inet][dec] first mfd: [dec]vlan extra RPF-MFD

This message happens when there are multiple MFD in hardware switched state.

cat6000-mmls

"This is just a informative message. If there are to many packets going to CPU the MTU on the interfaces should be changed appropriately to take advantage of hardware replication."

MLSM-6-MIN_MTU_UNSUPPORTED

6-Information

Outgoing interfaces with MTU less than the RPF interface will be multicast replicated to in software

-

cat6000-mmls

"This is just a informative message. If there are to many packets going to CPU the MTU on the interfaces should be changed appropriately to take advantage of hardware replication."

MLSM-6-SM_INSTALL_FAILURE

6-Information

interface/mask entry installation failed on [inet]/[dec] vlan[dec]

This message happens when Interface/mask entry to punt directly connected sources to the router could not be installed in HW-CEF table. This happens system is running out of available CEF entries. In this situation there might be blackholing of traffic for the directly connected sources on this interface

cat6000-mmls

"Modify the network config such that hardware resource limitation is not hit and ensure that interface/mask entry is installed."

MLSM-6-PVLAN_INSTALL_FAILURE

6-Information

Unable to locate secondary-vlan for [inet][inet][dec]

This message happens when RP was not able to determine the secondary vlan for the source in secondary vlan. After finite retries RP gives up installing the shortcut in hardware. This can happen when a new flow is installed or when there is a RPF change. In such situations flow will be software switched.

cat6000-mmls

"Make sure ARP table is populated for sources in secondary vlan by explicity 'ping'ing the source and the ARP table should contain the primary as well as secondary vlan information. To enable creation of hardware shortcut do a 'clear ip mroute <group> <source>' for the specific flow."

MLSM-6-LC_SCP_FAILURE

6-Information

NMP encountered internal communication failure for [inet][inet][dec]

This message happens SP was not able to update CEF tables on atleast one of the EARLs on Linecards.

cat6000-mmls

"Under some condition SP was not able to communicate with Linecard to update the multicast-CEF table. And this causes inconsistency in the CEF table among different line cards. This shortcut is deleted so that inconsistent state is purged. And this flow will get software forwarded."

MLSM-6-CONFIG_MISMATCH

6-Information

Multicast hardware switching config mis-match between RP and NMP. It is likely to be disabled on the NMP

MLS multicast hardware switching has been enabled on the RP but likely disabled on the NMP

cat6000

"Correct the mis-config by enabling IGMP snooping and MMLS on the NMP"

MLSM-6-CONFIG_MISMATCH_RECOVERED

6-Information

Multicast hardware switching mismatch recovered from earlier config mis-match

MMLS Config mismatch between RP and SP recovered from mismatch. The MLS multicast hardware switching is likely to be enabled on the NMP

cat6000-mmls

"Modify the network config such that hardware resource limitation is not hit and ensure that sg or *g entry is installed."

MLSM-6-MMLS_LEGACY_INSERTED

6-Information

MMLS: Legacy Linecard Inserted Egress Replication Mode will be disabled

Egress Replication is not supported with Legacy Cards system will transition to Ingress Mode please note that the transition will cause temporary loss of traffic

cat6000

"If the system is required to operate in Egress Replication Mode the Legacy lincard should be removed"

MLSM-6-MMLS_MODE_CHANGE

6-Information

MMLS: Replication Mode Changed to [chars] mode [chars]

When auto detection of replication mode is enabled the system will transition to ingress mode when an egress incapable linecard is inserted. The system will transition back to egress mode when the last egress incapable linecard is removed

cat6000

"Transition between ingress and egress mode will cause temporary loss of traffic to prevent this use the command mls ip replication-mode ingress"

MLSM-6-MMLS_NO_EGRESS_LOCAL_IN_INGRESS

6-Information

MMLS: Egress Local feature is NOT applicable in Ingress mode

When the system transistions from Egress replication mode to ingress the Egress Local feature will become non-applicable even if the Egress Local feature is enabled.

cat6000

"This is only to inform the user that Egress Local feature is not applicable in Ingress mode. If the Egress Local feature is required actions need to be taken to restore the system replication mode to egress"

MLSM-6-MMLS_EGRESS_INFO

6-Information

MMLS: Please make sure no multicast traffic is going through egress incapable line cards when system is operating in egress mode

This message is to remind the user that there should be no multicast traffic going through egress incapable line cards while the system is operating in egress replication mode.

cat6000

"Check to see if there are any egress incapable line cards in the system. If there are egress incapable line cards make sure that there is no multicast traffic going through these cards"

MLSM-6-MLSM_PMS

6-Information

MMLS: MLSM is suspending the caller process [chars]

This message is to remind the user that MLSM is suspending the caller process. This happens when the MLSM routines are called from PIM/Mwheel context and MLSM routines does an process suspend

cat6000-mmls

"When MLSM suspends the caller process there is a possibility of data corruption for the data handled by the caller process"

IPMUX-3-V4_CACHE_FULL

3-Error

IPMux V4 Cache full - replacing active entry

The IPMux V4 cache is full and has replaced a current cache entry. \n\ IP Multiplexing performance may be impacted if this continues.

ipmux

"Increase the size of the cache using the \n\ 'ip mux cache' configuration command."

IPMUX-3-V6_CACHE_FULL

3-Error

IPMux V6 Cache full - replacing active entry

The IPMux V6 cache is full and has replaced a current cache entry. \n\ IP Multiplexing performance may be impacted if this continues.

ipmux

"Increase the size of the cache using the \n\ 'ipv6 mux cache' configuration command."

MPLS_IPRM-3-PATH_LABEL_GET

3-Error

[chars]

-

-

-

MPLS_IPRM-3-PATH_LABEL_GET

3-Error

[chars]

An attempt to access MPLS forwarding information for the specified prefix has failed.

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-PATH_LABEL_UPD

3-Error

[chars]

-

-

-

MPLS_IPRM-3-PATH_LABEL_UPD

3-Error

[chars]

An attempt to update MPLS forwarding information for the specified prefix has failed.

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-PATH_LABEL_DEL

3-Error

[chars]

-

-

-

MPLS_IPRM-3-PATH_LABEL_DEL

3-Error

[chars]

An attempt to delete MPLS forwarding information for the specified prefix has failed.

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-DB

3-Error

[chars]

-

-

-

MPLS_IPRM-3-DB

3-Error

[chars]

There is an inconsistency in the information required to request labels from or to process labels received from an IP label distribution module

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-DB_TABLE

3-Error

[chars]

-

-

-

MPLS_IPRM-3-DB_TABLE

3-Error

[chars]

There is an inconsistency in the information about a vrf tableid

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-DB_PATH

3-Error

[chars]

-

-

-

MPLS_IPRM-3-DB_PATH

3-Error

[chars]

There is an inconsistency in the information about a prefix path required to request labels from or to process labels received from an IP label distribution module

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-DB_TRANS

3-Error

[chars]

-

-

-

MPLS_IPRM-3-DB_TRANS

3-Error

[chars]

There is an inconsistency in the information about an ongoing transaction required to populate MPLS forwarding data structures for a prefix

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-DB_PNDG_DISC

3-Error

[chars]

-

-

-

MPLS_IPRM-3-DB_PNDG_DISC

3-Error

[chars]

There is an inconsistency in the information about a temporarily deferred action required to populate MPLS forwarding data structures for a prefix

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-WALK

3-Error

[chars]

-

-

-

MPLS_IPRM-3-WALK

3-Error

[chars]

A request by an IP label distribution module e.g. LDP BGP to walk

mpls-iprm

LOG_STD_ACTION

MPLS_IPRM-3-INTERNAL

3-Error

[chars]

-

-

-

MPLS_IPRM-3-INTERNAL

3-Error

[chars]

An operation required for proper operation of the IP rewrite manager has failed.

mpls-iprm

"LOG_STD_ACTION"

ROUTEMAP_IPC-2-NOMEMORY

2-Critical

Alloc fail for route-map ipc buffer

Unable to malloc a buffer to send route-map configuration down to linecards.

-

"Enter a show chunks command and report the output along with" " this error message to your technical support representative."

ROUTEMAP_IPC-2-ROUTEMAPNAMELENEXCEEDED

2-Critical

The length of route map name tag is too long

The length of route map name tag is too long for IPC. The receiver has a 256 character long limit on route map name tag

-

"Use a route map name tag with the length of 256 or less characters"

POLICY_API-4-POLICYOVERIDE

4-Warning

Dynamic policy overriding static on intf:[chars]

Static policy and dynamic policy are configured on the\n\ interface. The dynamic policy will override the static\n\ policy.

-

"Remove the static policy config if desired."

POLICY_API-4-POLICYSTATICCLR

4-Warning

Static policy on intf:[chars] cleared. Dynamic policy in use.

A dynamic policy was overriding the static policy.\n\ Static policy has been cleared.

-

"No action required."

POLICY_API-4-POLICYDYNCLR

4-Warning

Dynamic policy on intf:[chars] cleared. Static policy in use.

A dynamic policy was overriding the static policy.\n\ The dynamic policy has been cleared the static policy\n\ is now in effect.

-

"No action required."

POLICY_API-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

-

-

VRFS-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

VRFS_DDTS_COMPONENT

LOG_STD_ACTION

VRFS-3-SBNOFN

3-Error

Missing [chars] subblock [chars] function for [chars]

Functions for distributing this subblock are missing from the image.

VRFS_DDTS_COMPONENT

LOG_STD_ACTION

IPMOBILE-6-REDUPDATEFAIL

6-Information

Too many redundancy update failures [dec] in the last minute.

A mobile router's attempt to dynamically add or delete a\n\ mobile network failed because that mobile network was already\n\ configured as a virtual network in the home agent.

mobileip

"To avoid duplication errors make sure that the virtual networks\n\ configuration on the home agent and the dynamic mobile network\n\ configuration on the mobile router do not have any overlapping\n\ network prefixes."

IPMOBILE-3-NOSOCKET

3-Error

Unable to open socket

The requested operation could not be accomplished because of a low\n\ memory condition.

mobileip

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

IPMOBILE-6-SECURE

6-Information

Security violation on [chars] from [chars] [chars] - errcode [chars] [dec]

A security violation occurred during registration attempt.

mobileip

"This is for informational purpose only."

IPMOBILE-2-ASSERTFAILED

2-Critical

IPMOBILE assertion failed: [chars]

The software detected an inconsistency. This is considered a\n\ serious error. The router attempts to continue but IP Mobility\n\ processing may be impaired.

mobileip

"Copy the error message exactly as it appears noting any IP Mobility\n\ problems that you are experiencing and report it to your technical\n\ support representative."

IPMOBILE-3-CONFIGERROR

3-Error

Standby FA configuration is not in sync with the active

The software detected an inconsistency in configuration between\n\ the standby and the active. Standby FA may not proceed with the\n\ sync for this visitor.

mobileip

"Re-configure standby FA and make sure the configuration between\n\ the standby and the active is in sync."

IPMOBILE-3-NOTUNNEL

3-Error

Maximum number of tunnels [dec] reached

The number of Mobile IP tunnels allowed on the box is reached.

mobileip

"This occures if the HA/FA is overloaded. \n\ If you suspect this condition contact technical\n\ support representative with the output of show tech"

IPMOBILE-5-MIP_TUNNELDELETE

5-Notice

Mobile IP tunnel [chars] deleting

The Mobile IP tunnel is going to be deleted.

mobileip

"This occurs if the active mobile ip binding is \n\ deleted.\n\ If you suspect this condition contact technical\n\ support representative with the output of show tech"

IPMOBILE-0-NOPROCESS

0-Emergency

\ [chars]

A Process could not be started

-

"Please contact your technical support representative\n\ with the error message you got and with the output of\n\ 'show process '."

IPMOBILE-0-IPMOBILE_DHCP

0-Emergency

\ [chars]

Two reasons for this error message\n\ 1. DHCP Client failed to get started this could be because of malloc\n\ failures.\n\ 2. IPMOBILE DHCP Process failed to start

mobileip

"If this error message is seen it is recommended not to use this\n\ HA for binding creation with DHCP Address Allocation.\n\ Check the available memory in the box and for the first reason try\n\ to get 'debug dhcp detail' before the failure.\n\ Contact your technical support representative with the error\n\ message you got."

IPMOBILE-3-SA_PARSE_FAILED

3-Error

Error in parsing the security association for [chars]

The Mobile IP Home Agent encountered an error while processing the Security Association in the RADIUS Access-Accept message.

mobileip

"Check the Radius profile config for the Mobile Node for which " "the processing of the Security Association failed."

IPV6_POLICY_API-4-IPV6_POLICYOVERIDE

4-Warning

Dynamic policy overriding static on intf:[chars]

Static policy and dynamic policy are configured on the interface. The dynamic policy will override the static policy.

ipv6

"Remove the static policy config if desired."

IPV6_POLICY_API-4-IPV6_LOCALPOLICYOVERIDE

4-Warning

Local dynamic policy overriding static local policy

Static policy and dynamic local policy are configured. The dynamic local policy will override the static local policy.

ipv6

"Remove the static local policy config if desired."

ISDN-6-CONNECT

6-Information

Interface [chars] is now connected to [chars] [chars]

-

-

LOG_STD_NO_ACTION

ISDN-6-DISCONNECT

6-Information

Interface [chars] disconnected from [chars] [chars] call lasted [dec] seconds

-

-

LOG_STD_NO_ACTION

ISDN-1-NOMEMORY

1-Alert

no memory for [chars]

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

ISDN-4-INVALID_SPID

4-Warning

Interface [chars] Spid[dec] was rejected

The SPID configured in the router has been rejected by the switch.

-

"Determine the correct SPID reenter the SPID and clear the\n\ BRI interface."

ISDN-4-INVALID_CALLEDNUMBER

4-Warning

Interface [chars] Ignoring call LDN and Called Party Number mismatch

The incoming ISDN call is ignored because the Called Party Number does\n\ not match the LDN numbers configured in the router.

-

"Correct the LDN in the router to match the Called Party\n\ Number delivered in the incoming setup message."

ISDN-4-INVALID_EID

4-Warning

Interface [chars] Ignoring call EndPoint Identifier EID mismatch

The incoming ISDN call is ignored because the EID delivered in the\n\ incoming setup message cannot be matched.

-

"If EID is delivered in the setup message use the <bold> isdn\n\ debugs <nobold> and <bold> show isdn status <nobold> commands\n\ to determine the current EID values. You may need to contact\n\ the service provider."

ISDN-6-LAYER2UP

6-Information

Layer 2 for Interface [chars] TEI [dec] changed to up

This is an informational message. It is sent when an ISDN Layer2\n\ logical link is up. It also shows the TEI associated with this\n\ logical link.

-

LOG_STD_NO_ACTION

ISDN-3-LAYER2_UP

3-Error

Layer 2 for Interface [chars] TEI [dec] changed to up

This is an informational message but being logged as an ERR at request\n\ from some customers. It is sent when an ISDN Layer2 logical link is up.\n\ It also shows the TEI associated with this logical link.

-

LOG_STD_NO_ACTION

ISDN-6-LAYER2DOWN

6-Information

Layer 2 for Interface [chars] TEI [dec] changed to down

This is an informational message. It is sent when an ISDN Layer2\n\ logical link is down. It also shows the TEI associated with this\n\ logical link.

-

LOG_STD_NO_ACTION

ISDN-3-LAYER2_DOWN

3-Error

Layer 2 for Interface [chars] TEI [dec] changed to down

This is an informational message but being logged as ERR at request\n\ from some customers. It is sent when an ISDN Layer2 logical link is \n\ down. It also shows the TEI associated with this logical link.

-

LOG_STD_NO_ACTION

ISDN-6-CHAN_UNAVAILABLE

6-Information

Interface [chars] Requested Channel [dec] is not available

This is an informational message. It is sent when the requested\n\ channel is not available.

-

"No action is required."

ISDN-6-CALL_COLLISION

6-Information

Interface [chars] Call Cid 0x[hec] Cref 0x[hec] collision on Channel [dec] in_use_cid 0x[hec] cref 0x[hec] Channel awarded to the received call

This is an informational message. It is sent when a Call is\n\ received that collides with an existing call on the same channel.

-

"No action is required."

ISDN-6-NO_TIMER

6-Information

No Free Timer Entry caller 0x[hec] timers used [dec]

This could be an indication of low memory. It is sent when the ISDN \n\ protocol cannot start new timers for it's operation.

-

"capture the show isdn mem show isdn status output for possible \n\ debugging information. Reduce other system activity to ease the \n\ memory demands in the system."

ISDN-6-INVALID_TIMER

6-Information

[chars]: Invalid Timer Handle caller 0x[hec] handle %3d

This could be an indication of low memory. It is sent when \n\ an invalid ISDN timer handle is passed on for timer operations

-

"capture the show isdn mem show isdn status output for possible \n\ debugging information. Reduce other system activity to ease the \n\ memory demands in the system."

ISDN-4-INVALID_EVENT

4-Warning

[chars]: Bad Event Received For Current State

The State Transition for the ISDN L2 Socket Process failed.

-

LOG_STD_SH_TECH_ACTION

ISDN-4-SPURIOUS_CONNECT

4-Warning

[chars]: Spurious Connection Accepted and Closed on port [dec]

An unknown TCP connection was accepted and refused.

-

LOG_STD_SH_TECH_ACTION

ISDN-4-GET_STATUS_STATE_FAIL

4-Warning

[chars]: isdn_get_status_state: Unknown DSL [dec]

An attempt to retrieve the status of a DSL that \n\is not currently configured.

-

LOG_STD_SH_TECH_ACTION

ISDN-4-ISDN_L2_INTERFACE_NOT_REGISTERED

4-Warning

[chars]: isdn_to_L2: Unknown DSL [dec] for command [chars]

The ISDN Stack has not registered its L2 Message Handler

-

LOG_STD_SH_TECH_ACTION

ISDN-4-BAD_DSL_FOR_CREATE_DELETE_L2

4-Warning

[chars]: isdn_create_delete_signalling_channel: Unknown DSL [dec] for\n\ [chars]

The Creation/Deletion service for the L2 Signalling handler\n\for the given DSL is missing

-

LOG_STD_SH_TECH_ACTION

ISDN-4-OPEN_TEMP_SOCKET_FAIL

4-Warning

[chars]: Failed to Open Required Temporary Socket[chars]

-

-

LOG_STD_SH_TECH_ACTION

ISDN-4-ISDN_UNEXPECTED_EVENT

4-Warning

[chars]: Occurred at [chars]:[dec]

An unexpected event of significance has occurred

-

LOG_STD_SH_TECH_ACTION

ISDN-4-RLM_STATUS_CHANGE

4-Warning

ISDN SC [chars]: Status Changed to: [chars].

ISDN has been notified by the RLM component of a \n\status change in the RLM link

-

LOG_STD_NO_ACTION

ISDN-2-ISDN_GENERAL_TRACEBACK

2-Critical

[chars]:[dec]

A debug - traceback condition has occurred

-

LOG_STD_NO_ACTION

ISDN-3-ISDN_RESOURCE_UNAVAILABLE

3-Error

[chars]: Resource not available at [chars]:[dec]

Hardware resource could not be allocated

-

LOG_STD_ACTION

ISDN-2-ISDN_FATAL

2-Critical

ISDN FATAL ERROR: file [chars] function [chars] message: [chars]

ISDN has detected a fatal system error.

-

LOG_STD_ACTION

ISDN-3-ISDN_CCB_FREE

3-Error

[chars]: CCB with call id 0x%04X on b channel [dec] was leaked but has been freed by ISDN Housekeeping. Reason: [chars]

A data structure internal to ISDN has leaked.

isdn

LOG_STD_NO_ACTION

ISDN-3-ISDN_CCB_FREE_FAILS

3-Error

[chars]: CCB with call id 0x%04X on b channel [dec] was leaked reason: [chars] and can't be free'd by ISDN Housekeeping.

A data structure internal to ISDN has leaked and we can't fix it for some reason.

isdn

LOG_STD_NO_ACTION

ISDN-4-ISDN_CCB_LEAK

4-Warning

[chars]: CCB with callid 0x%04X on b channel [dec] has been leaked. Reason: [chars]

A data structure internal to ISDN has been leaked

isdn

LOG_STD_NO_ACTION

ISDN-4-SERVICE

4-Warning

Interface [chars] [chars] [chars] message for chan [dec] state [chars]

This is an informational message but will be logged as a \n\ warning message if so configured.

-

"No action is required."

ISDN-4-RESTART

4-Warning

Interface [chars] [chars] [chars] message with restart class of [chars] chan [dec]

This is an informational message but will logged as a \n\ warning message if so configured.

-

"No action is required."

ISDN-4-STATUS

4-Warning

Interface [chars] [chars] [chars] st 0x[hec] ev 0x[hec] cid 0x[hec] cref 0x[hec]

This is an informational message but being logged as a \n\ warning message if so configured.

-

"No action is required."

ISDN-4-SERV_AUDIT_C1

4-Warning

Interface [chars] service audit trigger condition [dec] on channel [dec]

This is an informational message but will be logged as a warning message if so configured.

-

"No action is required."

ISDN-5-SERV_AUDIT_C2

5-Notice

Interface [chars] service audit trigger condition [dec] on channel [dec]

This is an informational message but will be logged as a warning message if so configured.

-

"No action is required."

ISDN-6-SERV_AUDIT_C3

6-Information

Interface [chars] service audit trigger condition [dec] on channel [dec]

This is an informational message but will be logged as a warning message if so configured.

-

"No action is required."

ISDN-4-ISDN_NLCB_LEAK

4-Warning

[chars]: NLCB leak detected. nlcb %X call id 0x%04X reason: [chars]

A data structure internal to ISDN has not been freed

isdn

LOG_STD_NO_ACTION

ISDN-3-ISDN_NLCB_FREE

3-Error

[chars]: NLCB with call id 0x%04X was leaked but has been freed by ISDN Housekeeping. Reason: [chars]

A data structure internal to ISDN has leaked.

isdn

LOG_STD_NO_ACTION

ISDN-6-REPEATED_SETUP

6-Information

Interface [chars] Call Cid 0x%04X Cref 0x%04X received a retransmitted setup on channel [dec] in_use_cid 0x%04X cref 0x%04X.

This is an informational message sent when a duplicate SETUP message is received on a B-channel. This indicates that the rate of calls being received is momentarily greater than the rate calls can be processed. No action is required.

-

LOG_STD_NO_ACTION

ISDN-6-NFAS_STATUS_CHANGE

6-Information

[chars] [chars] [chars] [chars]

The NFAS D-channel status has changed.

-

LOG_NO_ACTION

ISDN-2-ISDN_EXIT

2-Critical

[chars]

The ISDN task has terminated execution for the specified reason and may cause CISCO IOS to terminate.

-

LOG_STD_ACTION

L2CTRL-3-ADD_REGISTRY_FAILED

3-Error

Subsystem [chars] fails to add callback function [chars]

Other subsystem must have mistakenly add its own callback functions. This syslog is for debugging purpose.

l2ctrl

LOG_STD_NO_ACTION

L2FIB-3-BAD_PARAM

3-Error

[chars]

Invalid parameter

l2fib

LOG_STD_ACTION

L2FIB-3-EVPN_ERROR

3-Error

[chars]

EVPN encap error

l2fib

LOG_STD_ACTION

L2FIB-3-IMET_ENCAP_MISMATCH

3-Error

IMET Encapsulation Mismatch on bridge domain [dec] from [chars]

-

-

-

L2FIB-3-IMET_REPTYPE_MISMATCH

3-Error

IMET Replication Mismatch on bridge domain [dec] from [chars] Local is Static

-

l2fib

LOG_STD_ACTION

L2FIB-3-MAC_ENCAP_MISMATCH

3-Error

MAC [chars] Encapsulation Mismatch on bridge domain [dec] from [chars]

Incompatible Encapsulation Type in MAC/IP Route RT-2 received from remote peer

l2fib

LOG_STD_ACTION

L2FIB-3-MAC_ERROR

3-Error

MAC address [chars] is reserved for [chars] output list bit is produced by [chars] on bridge domain [dec]

-

l2fib

LOG_STD_ACTION

L3MM-5-WLAN

5-Notice

Wireless LAN Module in slot [dec] is [chars]

The L3MM detected a change in the state of the Wireless LAN module in the specified slot. If the module is now on line L3MM starts accepting access-point and mobile-node registrations from the WDS on the module. If the module is now off line L3MM purges all access points and mobile nodes received from the module.

-

LOG_STD_NO_ACTION

L3MM-5-WLAN_PWR_DN

5-Notice

Wireless LAN Module in slot [dec] will be powered down another module is already active

The L3MM detected a Wireless LAN module trying to come online while another module was already functional as the active Wireless LAN module. The L3MM does not support more than one Wireles LAN module online in the chassis at a given time which is why this module will be powered down

-

LOG_STD_NO_ACTION

L3MM-5-WLAN_COMM_ABORT

5-Notice

Communication with Wireless LAN Module in slot [dec] aborted [chars]

The Layer 3 Mobility Manager detected communication failure with the Wireless LAN module specified in the error message above and will respond as if the module went offline by purging its access point and mobile node databases. However the module will not be reset by the Layer 3 Mobility Manager

-

LOG_STD_NO_ACTION

L3MM-4-DUP_IPADDR

4-Warning

MN [enet] is requesting ip [inet] which is being used by MN [enet]

The L3MM detected that a mobile node requested an IP address that is being used by another mobile node in the network.

-

"Change the IP address of one of the two mobile " "nodes"

L3MM-4-MALLOC_FAIL

4-Warning

Memory allocation failure [chars]

The L3MM failed to allocate memory which was needed to perform a given operation and/or respond to an event

-

"Increase the memory on the RP of the supervisor"

L3MM-4-MN_MACDB_DEL

4-Warning

Failed to delete MN from MAC DB { MN: [enet] [inet] AP: [inet] WNID: [dec] }

The L3MM failed to delete the entry for the specified MN from the MN MAC database

cat6000-wireless

"Copy the error message exactly as it appears and report it to your " "technical support representative."

L3MM-4-MN_MACDB_ADD

4-Warning

Failed to add MN to MAC DB { MN: [enet] AP: [inet] }

The L3MM failed to add the entry for the specified MN into the MN MAC database

cat6000-wireless

"Copy the error message exactly as it appears and report it to your " "technical support representative."

L3MM-4-MN_IPDB_DEL

4-Warning

Failed to delete MN from IP DB { MN: [enet] [inet]}

The L3MM failed to delete the entry for the specified MN from the MN IP database

cat6000-wireless

"Copy the error message exactly as it appears and report it to your " "technical support representative."

L3MM-4-MN_IPDB_ADD

4-Warning

Failed to add MN to MN DB { MN: [enet] [inet]}

The L3MM failed to add the entry for the specified MN into the MN IP database

cat6000-wireless

"Copy the error message exactly as it appears and report it to your " "technical support representative."

L3MM-4-DUP_AP_IPADDR

4-Warning

AP [enet] is requesting ip [inet] which is being used by another AP

The L3MM detected that an access point requested an IP address that is being used by another access point in the network.

-

"Change the IP address of one of the two access " "points"

L3MM-4-AP_DB_ADD

4-Warning

Failed to add AP to DB { AP: [enet] [inet]}

The L3MM failed to add the entry for the specified AP into the AP database

cat6000-wireless

"Copy the error message exactly as it appears and report it to your " "technical support representative."

L3MM-4-AP_DB_DEL

4-Warning

Failed to delete AP from DB { AP: [enet] [inet]}

The L3MM failed to initialize due to the specified reason

cat6000-wireless

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ETHERNET_PMLACP-3-SYS_CFG_DUPL_ID

3-Error

Remote P-mLACP peer has duplicate P-mLACP node-id [dec]

A remote P-mLACP peer is configured with the same P-mLACP node-id as this device.

lacp

"Reconfigure the P-mLACP node-id to be unique between the two " "devices with the <CmdBold>mlacp node-id<NoCmdBold> configuration " "command. Refer to the P-mLACP configuration section of the Cisco " "IOS documentation for more information on configuring P-mLACP."

ETHERNET_PMLACP-3-SYS_CFG_INVALID_ID

3-Error

Received invalid P-mLACP node-id [dec] from peer

A remote P-mLACP peer is configured with an invalid P-mLACP node-id.

lacp

"Reconfigure the peer to send a valid P-mLACP node-id with the " "<CmdBold>mlacp node-id<NoCmdBold> configuration command. Refer " "to the P-mLACP configuration section of the Cisco IOS documentation " "for more information on configuring P-mLACP."

ETHERNET_PMLACP-3-PEER_ICCP_VERSION_INCOMPATIBLE

3-Error

Peer ICCP version [dec] is incompatible with local ICCP version [dec].

P-mLACP peer is running with a different version of ICCP. Incompatible ICCP would prevent P-mLACP from working properly.

lacp

"Reboot peer with identical IOS version would " "correct the issue. Compatible ICCP version between " "different IOS images can still be achieved by doing " "show lacp multichassis load-balance group on the both" " devices to check if ICCP versions are compatible. If ICCP " "versions are incompatible repeat IOS image loading " " and CLI above until a compatible image is loaded."

ETHERNET_PMLACP-4-ICRM_CLIENT_RECV_REJ

4-Warning

Received rejected P-mLACP TLV from peer with message ID [dec]

A remote P-mLACP peer has rejected an P-mLACP TLV.

lacp

"Issue the <CmdBold>show version<NoCmdBold> command on the local and remote " "devices to get the versions of IOS that are running. Reference the P-mLACP " "section of the IOS documentation to verify that P-mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices."

ETHERNET_PMLACP-4-ICRM_CLIENT_RECV_BAD_LEN

4-Warning

Received an P-mLACP TLV with bad length [dec] total message length [dec]

The P-mLACP TLV length is longer than the total message length.

lacp

"Issue the <CmdBold>show version<NoCmdBold> command on the local and remote " "devices to get the versions of IOS that are running. Reference the P-mLACP section " "of the IOS documentation to verify that P-mLACP is compatible between the IOS " "versions on the two devices. If the versions are compatible and the message still " "appears then please contact your Cisco technical support representative. Provide " "the representative with the exact message being seen as well as the output of the " "following commands <CmdBold>show version<NoCmdBold> <CmdBold>show run<NoCmdBold> " "<CmdBold>show lacp multi-chassis load-balance group<NoCmdBold> and <CmdBold>show lacp " "multi-chassis load-balance port-channel<NoCmdBold>."

ETHERNET_PMLACP-4-ICRM_CLIENT_RECV_NO_TYPELEN

4-Warning

Received an P-mLACP TLV without a type and/or length field [dec]

P-mLACP received an improperly formatted TLV from the peer. As a result the local and peer devices may have mismatched state data.

lacp

"Issue the <CmdBold>show version<NoCmdBold> command on the local and remote " "devices to get the versions of IOS that are running. Reference the P-mLACP " "section of the IOS documentation to verify that P-mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices."

ETHERNET_PMLACP-4-CORE_ISOLATION

4-Warning

P-mLACP Core isolation failure: Attempting to failover [dec] ports in redundancy group [dec]

P-mLACP has detected isolation from the core and has attempted to failover.

lacp

"Use the <CmdBold>show interchassis redundancy<NoCmdBold> command to determine " "which core facing interface has triggered the isolation failure. Correct the " "failure for the given interface this will clear the P-mLACP core isolation " "failure. Reference the P-mLACP section of the IOS documentation for more " "information on core isolation failures and related configuration commands."

ETHERNET_PMLACP-4-CORE_CONNECTED

4-Warning

P-mLACP has recovered from a core isolation failure. Attempting to recover [dec] ports in redundancy group [dec]

P-mLACP has recovered from core isolation and has attempted to recover the ports in the redundancy group.

lacp

"This message may not require any action. However the " "<CmdBold>show lacp multi-chassis load-balance group<NoCmdBold> and " "<CmdBold>show lacp multi-chassis load-balance port-channel<NoCmdBold> commands " "may be used to verify the state of the P-mLACP port-channels. Reference " "the P-mLACP section of the IOS documentation for details on core isolation " "failures and related configuration commands."

ETHERNET_PMLACP-4-PEER_DOWN

4-Warning

P-mLACP Peer down failure: Attempting to make [dec] local ports active in redundancy group [dec]

P-mLACP has detected a peer down failure and has attempted to make the local port-channels become active.

lacp

"The peer down failure should be corrected by re-enabling communication " "with the peer P-mLACP device. Use the <CmdBold>show redundancy interchassis<NoCmdBold> " "command on both the local and peer P-mLACP devices to determine which peer member IP " "has lost communication. Use this information to further debug the network communication " "issue and re-enable communication with the peer. Reference the P-mLACP section of the IOS " "documentation for more information on peer down failures."

ETHERNET_PMLACP-4-PEER_UP

4-Warning

P-mLACP has recovered from a peer down failure in redundancy group [dec]

P-mLACP is now in communication with the peer device and has recovered from a previous peer down failure.

lacp

"This message may not require any action. However the " "<CmdBold>show lacp multi-chassis load-balance group<NoCmdBold> and " "<CmdBold>show lacp multi-chassis load-balance port-channel<NoCmdBold> commands may be used " "to verify the state of the P-mLACP port-channels. Reference the P-mLACP section " "of the IOS documentation for details on peer down failures and related " "configuration commands."

ETHERNET_PMLACP-4-PEER_DISCONNECT

4-Warning

An P-mLACP peer has disconnected from redundancy group [dec] attempting to reconnect

P-mLACP has detected that a peer device from the specified redundancy group has disconnected. P-mLACP will attempt to reconnect to the device until successful.

lacp

"This message is typically caused by a configuration event on the peer router and " "so no action may be necessary. However if this message is unexpected then issue " "the <CmdBold>show redundancy interchassis<NoCmdBold> command on both the local and " "peer P-mLACP devices to determine which peer member IP has lost communication. Use this " "information to further debug the network communication issue and re-enable communication " "with the peer. Reference the P-mLACP section of the IOS documentation for more information " "on peer down failures."

ETHERNET_PMLACP-4-PEER_RECONNECT_FAILED

4-Warning

The attempt to reconnect to the peer in redundancy group [dec] has failed

After an P-mLACP peer device disconnected an attempt was made to reconnect however that attempt has failed.

lacp

"To reinitialize the connection unconfigure <CmdBold>mlacp interchassis group<NoCmdBold> " "from the port-channel and then reconfigure it. After doing that issue " "<CmdBold>show redundancy interchassis<NoCmdBold> to get the peer member IP " "connection status and the P-mLACP connection state. If the peer member IP " "connection status is not CONNECTED then there is a more basic communication " "issue that needs to be fixed. Otherwise if the peer member IP is CONNECTED but " "the P-mLACP state is not CONNECTED then there could be a software issue. In that " "case collect the output of <CmdBold>show redundancy interchassis<NoCmdBold> " "<CmdBold>show lacp multi-chassis load-balance group<NoCmdBold> and " "<CmdBold>show lacp multi-chassis load-balance port-channel<NoCmdBold>. Then please contact your " "Cisco technical support representative and provide the collected information."

ETHERNET_PMLACP-6-PEER_CONNECT

6-Information

P-mLACP peer is now connected in redundancy group [dec]

This message indicates that the local P-mLACP device is now connected to a peer device in the specified redundancy group.

lacp

"No action is required. To view the peer information the command " "<CmdBold>show lacp multi-chassis load-balance port-channel<NoCmdBold> or " "<CmdBold>show lacp multi-chassis load-balance group<NoCmdBold> may be issued."

ETHERNET_MLACP-3-SYS_CFG_DUPL_ID

3-Error

Remote mLACP peer has duplicate mLACP node-id [dec]

A remote mLACP peer is configured with the same mLACP node-id as this device.

lacp

"Reconfigure the mLACP node-id to be unique between the two " "devices with the <CmdBold>mlacp node-id<NoCmdBold> configuration " "command. Refer to the mLACP configuration section of the Cisco " "IOS documentation for more information on configuring mLACP."

ETHERNET_MLACP-3-SYS_CFG_INVALID_ID

3-Error

Received invalid mLACP node-id [dec] from peer

A remote mLACP peer is configured with an invalid mLACP node-id.

lacp

"Reconfigure the peer to send a valid mLACP node-id with the " "<CmdBold>mlacp node-id<NoCmdBold> configuration command. Refer " "to the mLACP configuration section of the Cisco IOS documentation " "for more information on configuring mLACP."

ETHERNET_MLACP-3-PEER_ICCP_VERSION_INCOMPATIBLE

3-Error

Peer ICCP version [dec] is incompatible with local ICCP version [dec].

mLACP peer is running with a different version of ICCP. Incompatible ICCP would prevent mLACP from working properly.

lacp

"Reboot peer with identical IOS version would " "correct the issue. Compatible ICCP version between " "different IOS images can still be achieved by doing " "show lacp multichassis group on the both devices to " "check if ICCP versions are compatible. If ICCP " "versions are incompatible repeat IOS image loading " " and CLI above until a compatible image is loaded."

ETHERNET_MLACP-4-ICRM_CLIENT_RECV_REJ

4-Warning

Received rejected mLACP TLV from peer with message ID [dec]

A remote mLACP peer has rejected an mLACP TLV.

lacp

"Issue the <CmdBold>show version<NoCmdBold> command on the local and remote " "devices to get the versions of IOS that are running. Reference the mLACP " "section of the IOS documentation to verify that mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices."

ETHERNET_MLACP-4-ICRM_CLIENT_RECV_BAD_LEN

4-Warning

Received an mLACP TLV with bad length [dec] total message length [dec]

The mLACP TLV length is longer than the total message length.

lacp

"Issue the <CmdBold>show version<NoCmdBold> command on the local and remote " "devices to get the versions of IOS that are running. Reference the mLACP section " "of the IOS documentation to verify that mLACP is compatible between the IOS " "versions on the two devices. If the versions are compatible and the message still " "appears then please contact your Cisco technical support representative. Provide " "the representative with the exact message being seen as well as the output of the " "following commands <CmdBold>show version<NoCmdBold> <CmdBold>show run<NoCmdBold> " "<CmdBold>show lacp multi-chassis group<NoCmdBold> and <CmdBold>show lacp " "multi-chassis port-channel<NoCmdBold>."

ETHERNET_MLACP-4-ICRM_CLIENT_RECV_NO_TYPELEN

4-Warning

Received an mLACP TLV without a type and/or length field [dec]

mLACP received an improperly formatted TLV from the peer. As a result the local and peer devices may have mismatched state data.

lacp

"Issue the <CmdBold>show version<NoCmdBold> command on the local and remote " "devices to get the versions of IOS that are running. Reference the mLACP " "section of the IOS documentation to verify that mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices."

ETHERNET_MLACP-4-CORE_ISOLATION

4-Warning

mLACP Core isolation failure: Attempting to failover [dec] LAGs in redundancy group [dec]

mLACP has detected isolation from the core and has attempted to failover.

lacp

"Use the <CmdBold>show interchassis redundancy<NoCmdBold> command to determine " "which core facing interface has triggered the isolation failure. Correct the " "failure for the given interface this will clear the mLACP core isolation " "failure. Reference the mLACP section of the IOS documentation for more " "information on core isolation failures and related configuration commands."

ETHERNET_MLACP-4-CORE_CONNECTED

4-Warning

mLACP has recovered from a core isolation failure. Attempting to recover [dec] LAGs in redundancy group [dec]

mLACP has recovered from core isolation and has attempted to recover the LAGs in the redundancy group.

lacp

"This message may not require any action. However the " "<CmdBold>show lacp multi-chassis group<NoCmdBold> and " "<CmdBold>show lacp multi-chassis port-channel<NoCmdBold> commands " "may be used to verify the state of the mLACP port-channels. Reference " "the mLACP section of the IOS documentation for details on core isolation " "failures and related configuration commands."

ETHERNET_MLACP-4-PEER_DOWN

4-Warning

mLACP Peer down failure: Attempting to make [dec] local LAGs active in redundancy group [dec]

mLACP has detected a peer down failure and has attempted to make the local port-channels become active.

lacp

"The peer down failure should be corrected by re-enabling communication " "with the peer mLACP device. Use the <CmdBold>show redundancy interchassis<NoCmdBold> " "command on both the local and peer mLACP devices to determine which peer member IP " "has lost communication. Use this information to further debug the network communication " "issue and re-enable communication with the peer. Reference the mLACP section of the IOS " "documentation for more information on peer down failures."

ETHERNET_MLACP-4-PEER_UP

4-Warning

mLACP has recovered from a peer down failure in redundancy group [dec]

mLACP is now in communication with the peer device and has recovered from a previous peer down failure.

lacp

"This message may not require any action. However the " "<CmdBold>show lacp multi-chassis group<NoCmdBold> and " "<CmdBold>show lacp multi-chassis port-channel<NoCmdBold> commands may be used " "to verify the state of the mLACP port-channels. Reference the mLACP section " "of the IOS documentation for details on peer down failures and related " "configuration commands."

ETHERNET_MLACP-4-PEER_DISCONNECT

4-Warning

An mLACP peer has disconnected from redundancy group [dec] attempting to reconnect

mLACP has detected that a peer device from the specified redundancy group has disconnected. mLACP will attempt to reconnect to the device until successful.

lacp

"This message is typically caused by a configuration event on the peer router and " "so no action may be necessary. However if this message is unexpected then issue " "the <CmdBold>show redundancy interchassis<NoCmdBold> command on both the local and " "peer mLACP devices to determine which peer member IP has lost communication. Use this " "information to further debug the network communication issue and re-enable communication " "with the peer. Reference the mLACP section of the IOS documentation for more information " "on peer down failures."

ETHERNET_MLACP-4-PEER_RECONNECT_FAILED

4-Warning

The attempt to reconnect to the peer in redundancy group [dec] has failed

After an mLACP peer device disconnected an attempt was made to reconnect however that attempt has failed.

lacp

"To reinitialize the connection unconfigure <CmdBold>mlacp interchassis group<NoCmdBold> " "from the port-channel and then reconfigure it. After doing that issue " "<CmdBold>show redundancy interchassis<NoCmdBold> to get the peer member IP " "connection status and the mLACP connection state. If the peer member IP " "connection status is not CONNECTED then there is a more basic communication " "issue that needs to be fixed. Otherwise if the peer member IP is CONNECTED but " "the mLACP state is not CONNECTED then there could be a software issue. In that " "case collect the output of <CmdBold>show redundancy interchassis<NoCmdBold> " "<CmdBold>show lacp multi-chassis group<NoCmdBold> and " "<CmdBold>show lacp multi-chassis port-channel<NoCmdBold>. Then please contact your " "Cisco technical support representative and provide the collected information."

ETHERNET_MLACP-6-PEER_CONNECT

6-Information

mLACP peer is now connected in redundancy group [dec]

This message indicates that the local mLACP device is now connected to a peer device in the specified redundancy group.

lacp

"No action is required. To view the peer information the command " "<CmdBold>show lacp multi-chassis port-channel<NoCmdBold> or " "<CmdBold>show lacp multi-chassis group<NoCmdBold> may be issued."

ETHERNET_MLACP-4-PC_CHANGE

4-Warning

mLACP [chars] status changed to [chars]

A mLACP port-channel state change event has occurred. This might have been caused by a mLACP failure or recovery event on the local or peer POA in the same redundancy group. It is normal to get these messages during provisioning and administrative actions on the mLACP port-channel.

lacp

"User should debug further to analyze root cause of the event. Use " "<CmdBold>show redundancy interchassis <NoCmdBold> " "<CmdBold>show lacp multi-chassis port-channel<NoCmdBold> " "<CmdBold>show lacp multi-chassis group<NoCmdBold> and " "<CmdBold>show lacp internal <NoCmdBold> on both POAs to check " "mLACP port-channel health. If any failure exists appropriate " "actions should be taken to recover port-channel from failure. " "If failure persists then please contact your Cisco technical " "support representative and provide the collected information."

ETHERNET_LACP-1-ISSU_NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low memory condition.

lacp

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

ETHERNET_LACP-3-ISSU_SENDFAILED

3-Error

\nLACP ISSU: send message failed rc = [dec]\n

The sending of a message has failed. This is an informational message only.

lacp

LOG_STD_SH_TECH_ACTION

ETHERNET_LACP-4-ISSU_INCOMPATIBLE

4-Warning

\nlacp-issu-compat: returned FALSE

The ISSU compatibility matrix check has failed. This is an informational message only.

lacp

LOG_STD_SH_TECH_ACTION

ETHERNET_LACP-4-ISSU_XFORM

4-Warning

\n[chars]: failed rc=[chars]

The ISSU transform has failed. This is an informational message only.

lacp

LOG_STD_SH_TECH_ACTION

ETHERNET_LACP-4-RF_CLIENT_INIT

4-Warning

\nLACP HA: Unable to initiate RF client.\n

LACP is unable to initialize as a RF client. This is an informational message only.

lacp

LOG_STD_SH_TECH_ACTION

ETHERNET_LACP-4-RF_CLIENT_BUNDLE

4-Warning

\nLACP HA: Unable initiate checkpoint bundle mode.\n

LACP is unable to initialize checkpoint bundle mode. This is an informational message only.

lacp

LOG_STD_SH_TECH_ACTION

LANE-3-BADTYPE

3-Error

Inappropriate LAN type

An unexpected LAN type has been specified for a LANE component.\n\ Only ethernet and token-ring elans are supported.

-

"Specify a valid LAN type."

LANE-3-BADNAME

3-Error

ELAN name must be 1-32 characters long

A name which is longer than 32 characters identifying a LANE \n\ component has been entered by the user.

-

"Re-enter a shorter name."

LANE-5-UPDOWN

5-Notice

[chars] [chars] [chars]: [chars] changed state to [chars]

A LANE component changed state to up/down.

-

"If this event is expected then take no action. Otherwise\n\ please contact a technical support representative."

LANE-6-INFO

6-Information

[chars]

LANE subsystem simple informational messages.

-

"None."

LANE-3-LANE_ERROR

3-Error

[chars]

An internal error has occured which reflects an inconsistency\n\ in the system and needs attention.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LANE-3-NOINT

3-Error

[chars] still destroying old sub-interface

An attempt was made to create a new subinterface while a previous\n\ version of the subinterface was still being destroyed.

-

"Wait a minute and try again. If failure still occurs try shutting\n\ down the main interface. Rebooting may be required to recover in\n\ extreme cases."

LANE-6-LEC_INFO

6-Information

[chars]

LANE client informational messages.

-

"None."

LANE-3-LEC_ERR

3-Error

[chars]

A LANE client software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LANE-3-LEC_CONTROL_MSG

3-Error

Received bad control message on interface [chars]

The LANE client received an unexpected or inappropriate control message \n\ over one of its vc's.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LANE-3-LEC_BADAD

3-Error

[chars] LEC unable to compute ATM address

The client cannot obtain an ATM address from the given configuration\n\ or auto-assignment failed to get an ATM prefix from the switch.

-

-

LANE-3-LEC_SIGNAL

3-Error

Unexpected SigAPI event [dec]

ATM signaling sent the LANE client an unexpected message type.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LANE-3-LEC_LISTEN

3-Error

[chars] listen failed on [chars]

The LANE client could not register its address with ATM signalling\n\ to be able to accepts calls on that address.

-

"Reconfigure the client ATM address. It may be conflicting with another\n\ component with the same ATM address."

LANE-3-LEC_JOIN

3-Error

[chars] JOIN failed [chars] LES returned [dec]

LANE client was rejected the Join request to join its elan.

-

"This is usually because of user configuration errors: LANE client\n\ attempting to join an incorrect elan or elan not configured\n\ in the LES or validation failures with the LECS etc..."

LANE-3-LEC_REGISTER

3-Error

[chars] REGISTER failed [chars] LES returned [dec]

attempt to register a mac-atm address binding with LES failed.

-

"The LES has already registered the requested mac addr - atm addr binding."

LANE-3-LEC_RD_REGISTER

3-Error

[chars] RD REGISTER failed for Route Descriptor [hec]

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LANE-3-LEC_CFG

3-Error

[chars] CFG_REQ failed [chars] LECS returned [dec]

The master LECS refused the LEC's configuration request.

-

"Check your LECS configurations."

LANE-3-LEC_BAD_CTL_DIST_TYPE

3-Error

[chars] CTL DIST blli type wrong

Wrong BLLI value specified on the incoming circuit.

-

"The originator of the circuit is not using the correct BLLI value\n\ for this type of circuit. LANE standard defines these values and\n\ the originator is violating the standard."

LANE-3-LEC_WRONG_ELAN_ID

3-Error

[chars]: elan id mismatch: LECS indicates [dec] LES indicates [dec]

The elan-id returned by LES does not match the value given by LECS or\n\ via the CLI

-

"Check configuration of elan ids specified in the LECS database and\n\ the LES. The mismatch must be occuring as a result of misconfiguration."

LANE-3-NAMECHG

3-Error

A LANE Client is already running here using another elan name

Both the LANE client and the LANE server/BUS may have an emulated LAN\n\ name specified in the configuration via the lane server-bus and lane\n\ client commands. If both specify the emulated LAN name then the name\n\ cannot be changed by re-entering just one of the commands.

-

"Use the no lane server-bus command to delete the server-bus or the no\n\ lane client command to delete the client. Then the other of the two\n\ commands can be re-entered with another emulated LAN name. Finally\n\ re-enter the deleted command with the new emulated LAN name."

LANE-3-TYPECHG

3-Error

A LANE Client is already running here using another elan type

-

-

"Use the no lane server-bus command to delete the server-bus or the no\n\ lane client command to delete the client. Then the other of the two\n\ commands can be re-entered with a new type. Finally re-enter the\n\ deleted command with the new type."

LANE-4-LSV_LECID

4-Warning

[chars] elan [chars] LECIDs exhausted

The LANE server specified has 65279 clients. No more can be added.

-

"Change the configurations to avoid trying to have more than 65279 LANE\n\ clients on this server."

LANE-3-LSV_CRASH

3-Error

[chars] elan [chars] unrecoverable error [chars]

A very serious LES/BUS internal error occurred.

-

"This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration."

LANE-4-LSV_ADDR

4-Warning

[chars] elan [chars] unable to register LES/BUS ATM addr

LANE Server or BUS could not register its address with ILMI.

-

"Try and investigate why. Some of the reasons are: user defined\n\ override address does not conform to the switch prefix or that\n\ there is a problem with the ATM switch with whom the entity is \n\ registering."

LANE-3-LSV_BADAD

3-Error

[chars] elan [chars] unable to compute [chars] ATM address

-

-

"Enter a correct ATM address template for the LANE component \"BUS\"\n\ \"server\" or \"config server\" named in the error message."

LANE-3-NOILMI

3-Error

ILMI service registration failed

-

-

"This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration."

LANE-3-BADILMI

3-Error

Unexpected ILMI event [dec]

An internal error occurred.

-

"This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration."

LANE-3-NOREGILMI

3-Error

[chars] [chars] cannot register %Cj with ILMI

An attempt to register the given ATM address with the ATM switch\n\ failed. This failure can occur because the ATM switch is down or\n\ misconfigured. The registration will be retried.

-

"If the situation persists after a number of attempts and the switch\n\ is up the configuration of the switch and router should be examined. A \n\ likely cause is that the ATM address being registered is not\n\ compatible with the parameters configured in the switch. Correct the configuration."

LANE-3-LES_ERROR

3-Error

[chars]

A serious internal occured with LES/BUS.

-

"This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration."

LANE-6-LES_INFO

6-Information

[chars]

Simple informational LES messages.

-

"None."

LANE-3-LECS_ERROR

3-Error

MSG_TRACEBACK | MSG_PROCESS

-

-

-

LANE-4-LECS_WARNING

4-Warning

[chars]

-

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LANE-6-LECS_INFO

6-Information

[chars]

Simple informational LECS messages.

-

"None."

LANE-3-LANE_SIG_ERR

3-Error

[chars]

An internal error occurred while system routines were handling ATM\n\ signaling messages for LANE.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

LAT-3-NOSYNC

3-Error

Tty[t-line] Output data ptrs out of sync with byte count

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

LAT-3-BADDATA

3-Error

Tty[t-line] Data pointer does not correspond to current packet

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

LAT-3-REUSE

3-Error

Tty[t-line] Attempt to re-use slot array empty = [dec] fill = [dec]

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

LAT-3-QBSPACED

3-Error

Queue block at [hec] not found for HI connection

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

LAT-3-BUFFULL

3-Error

Tty[t-line] data buffer full with count [dec]

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

LAT-3-NULLIDB

3-Error

Null IDB pointer with destination [enet]

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

MUESLIX-1-DWNLDFL

1-Alert

Mueslix microcode down load failed.

The Mueslix serial hardware failed. Hardware could not download \n\ microcode into mueslix chip.

mid-serial

LOG_STD_ACTION

MUESLIX-1-INITFAIL

1-Alert

MUESLIX slot [dec]: Init Failed at [chars]

The Mueslix serial board failed to complete hardware \n\ initialization.

mid-serial

LOG_STD_ACTION

MUESLIX-1-STARTFAIL

1-Alert

[chars]: Start Failed at [chars]

The Mueslix serial interface is not responding to commands used to \n\ initialize it.

mid-serial

LOG_STD_ACTION

MUESLIX-1-STOPFAIL

1-Alert

[chars]: Stop Failed at [chars]

The Mueslix serial board failed to respond to a request to \n\ disable an interface.

mid-serial

LOG_STD_ACTION

MUESLIX-3-OWNERR

3-Error

Unit [dec] buffer ownership error pak = 0x[hec]

The Mueslix serial driver detected that the transmit ring is in an \n\ inconsistent state.

mid-serial

LOG_STD_ACTION

RPS-3-THERMAL

3-Error

System detected Redundant Power System THERMAL FAIL condition.

The Redundant Power System experienced either a Fan failure\n\ or an Over Temperature condition.

-

"For 3600 and 2600 Redundant Power supplies look at the "FAN" and \n\ "TEMP" LEDs on the front of Power Supply. If the "FAN" LED is amber \n\ one of the fans has failed and you should replace the Redundant Power \n\ Supply. If the "TEMP" LED is amber the ambient temperature is too \n\ high. For 5300 RPS unit this message is displayed when the ambient\n\ temperature is too high."

RPS-3-DCOUTPUTVOLTFAIL

3-Error

System detected Redundant Power System DC Output Voltage failure condition.

The Redundant Power System experienced a DC Output Voltage failure\n\ condition in one of the power supplies.

-

"One of the DC outputs has failed on the Redundant Power Supply. \n\ For 3600 and 2600 Redundant Power supplies "DC Status" LED on the front of \n\ the Power Supply will identify which DC output has failed. For 5300 Redundant\n\ Power Supply "DC OK" LED on the front of the Power Supply will identify \n\ which DC output has failed. When there is a DC failure you need to replace \n\ the Redundant Power Supply."

RPS-3-INPUTVOLTFAIL

3-Error

System detected Redundant Power System Input Voltage failure condition.

The Redundant Power System experienced an Input Voltage failure\n\ in one of the power supplies.

-

"One of the AC or DC inputs has failed on the Redundant Power Supply. \n\ For 3600 and 2600 Redundant Power supplies "AC Input" LED on the front \n\ of the Power Supply will identify which AC input has failed. For 5300\n\ AC<->DC Redundant Power Supply "AC OK" LED on the front of the\n\ Power Supply will identify which AC input has failed. For 5300 DC<->DC\n\ Redundant Power Supply "DC Input" LED on the front of the Power Supply \n\ will identify which DC input has failed. Make sure that the AC/DC circuit \n\ in your building is operational verify that the power cord is plugged \n\ into the Redundant Power Supply and make sure that the AC/DC power \n\ switch on the Redundant Power Supply is on."

RPS-3-FANFAIL

3-Error

System detected Redundant Power System FAN FAIL condition.

The Redundant Power System experienced a Fan failure condition.

-

"One of the fans has failed and you should replace the Redundant Power \n\ Supply."

RPS-3-OVERVOLT

3-Error

Redundant Power System detected OVERVOLTAGE condition.

The Redundant Power System detected OVERVOLTAGE condition.

-

"The Redundant Power System detected an over voltage condition."

RPS-3-VOLTOK

3-Error

Redundant Power System VOLTAGE is now normal.

The Redundant Power System voltage is now normal.

-

"The Redundant Power System previously detected an over voltage \n\ condition which has now cleared."

RPS-3-OVERTEMP_OK

3-Error

System temperature is now normal.

The system is operating at a normal temperature.

-

"The system previously detected an over temperature condition\n\ which has now cleared. This is most likely due to high ambient \n\ temperature where the router is located."

RPS-3-THERMOK

3-Error

Redundant Power System THERMAL condition is now normal.

The Redundant Power System THERMAL is now normal.

-

"The Redundant Power Supply previously detected an over temperature \n\ condition which has now cleared. This is most likely due to high \n\ ambient temperature where the Redundant Power Supply is located. \n\ A Redundant Power System thermal failure can also be caused by a \n\ fan failure in the Redundant Power Supply."

RPS-3-FANOK

3-Error

Redundant Power System FAN condition is now normal.

The Redundant Power System FAN is now normal.

-

"The Redundant Power Supply previously detected fan failure\n\ condition which has now cleared."

RPS-3-DCOUTPUTVOLTOK

3-Error

Redundant Power System DC Output Voltage condition is now normal

The Redundant Power System DC Output Voltage is normal.

-

"This is an informational message only. No action is required."

RPS-3-INPUTVOLTOK

3-Error

Redundant Power System Input Voltage condition is now normal

The Redundant Power System Input Voltage is normal.

-

"This is an informational message only. No action is required."

RPS-3-RPSOK

3-Error

Redundant Power System is now normal

The Redundant Power System experienced multiple failures. This is a \n\ critical condition

-

"There are multiple failures on the Redundant Power Supply.\n\ Examine the LEDs on the front of the Redundant Power Supply to \n\ find out which failures it has."

BCM3220-1-INITFAIL

1-Alert

msgtxt_initfail

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

BCM3220-3-BADUNIT

3-Error

msgtxt_badunit

An internal software error occurred.

-

"If either message recurs call your technical support representative\n\ for assistance."

BCM3220-3-OWNERR

3-Error

msgtxt_ownerror

An Ethernet interface is malfunctioning or an internal software error\n\ occurred.

-

"Repair or replace the controller."

BCM3220-3-TXERR

3-Error

CM trasmission error occurred.

-

-

""

NIM-2-NOHWADDRESS

2-Critical

All hardware addresses have been allocated - maximum of [dec]\n

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NIM-2-BADSUBUNIT

2-Critical

Illegal reference to non-existent subunit [dec] in slot [dec]\n

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NIM-2-BADSLOT

2-Critical

Illegal reference to non-existent slot [dec]\n

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NIM-2-DEADICHAINQ

2-Critical

Attempted to manipulate uninitialized ichainQ in [chars]\n

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NIM-2-LOSTICHAINQ

2-Critical

Couldn't find idb 0x[hec] in ichainQ in [chars]\n

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NIM-2-BADNIMREV

2-Critical

Unsupported version of [chars] NIM in slot [dec] Version 0x[hec]\n

-

-

"Upgrade the NIM to the proper level."

NIM-2-UNSUPNIM

2-Critical

Unsupported [chars] NIM in slot [dec]\n

The indicated NIM is not supported on this platform.

-

"Remove the NIM."

TDM-1-TDM_MB_INITFAIL

1-Alert

Motherboard TDM init failure:\nstream [dec] channel [dec] channel register 0x[hec] control register 0x[hec].

A TDM port on the system motherboard failed to be initialized.\n\ The error message specifies which port. This is possibly due to\n\ a hardware failure.

-

LOG_STD_ACTION

TDM-1-TDM_INITFAIL

1-Alert

Slot [dec] TDM init failure:\nstream [dec] channel [dec] channel register 0x[hec] control register 0x[hec].

A TDM port failed to be initialized. \n\ The error message specifies which port. This is possibly due to\n\ a hardware failure.

-

LOG_STD_ACTION

TDM-3-TDM_BADUNIT

3-Error

Slot [dec] bad board ID 0x[hec] detected.

The specified board returned an ID that was not recognized by\n\ the operating system. This could be due to a hardware failure\n\ reporting an incorrect ID or because this software predates the\n\ hardware.

-

LOG_STD_ACTION

TDM-4-TDM_BAD_CONNECT

4-Warning

Bad connection requested: slot [dec] stream [dec] channel [dec] to slot [dec] stream [dec] channel [dec].

The TDM cross-connect that was requested was not possible.\n\ This is probably because one of the devices either does not exist\n\ or is not properly configured for TDM.

-

"Check the command for errors and the ports for correct configuration\n\ before trying again. Note that the \"type\" option of the \"tdm-group\"\n\ command only applies if the \"mode cas\" command is enabled.\n\ If configuring cross-connect pass-through from UIO serial\n\ port 0 or 1 to a controller the \"encapsulation clear-channel\"\n\ command must be configured on the serial port. "

ILACC-1-INITFAIL

1-Alert

msgtxt_initfail

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

ILACC-5-LATECOLL

5-Notice

Unit [dec] late collision error

An Ethernet transceiver is malfunctioning the Ethernet is overloaded\n\ or the Ethernet cable is too long.

-

"Repair or replace the controller."

ILACC-5-LOSTCARR

5-Notice

Unit [dec] lost carrier. Transceiver problem?

An Ethernet transceiver is unplugged or faulty.

-

"Repair or replace the controller."

ILACC-3-UNDERFLO

3-Error

Unit [dec] underflow error

The Ethernet hardware is requesting data faster than the system can\n\ supply it. This condition might indicate that the system is at the\n\ limit of its performance.

-

"A small number of underflows might not be a cause for concern. You can\n\ monitor underflows with the <Bold>show interface<NoBold> command. Reducing the load\n\ on the router or installing a higher-performance router should\n\ alleviate this problem."

ILACC-5-COLL

5-Notice

Unit [dec] excessive collisions. TDR=[dec]

-

-

"If the transceiver appears to be properly terminated repair or\n\ replace the Ethernet interface card."

ILACC-1-MEMERR

1-Alert

msgtxt_memoryerror

An Ethernet interface detected a hardware problem.

-

"Repair or replace the controller."

ILACC-4-BABBLE

4-Warning

Unit [dec] babble error csr0 = 0x[hec]

An Ethernet interface is malfunctioning.

-

"Determine whether the malfunction stems from a software or hardware\n\ error by turning off all fast switching. Error messages showing that the packet is too large for the link\n\ indicate a software error at a high level. Copy the error message exactly as it appears and report it to your\n\ technical support representative. Receiving no error messages indicates a hardware error. \n\ Repair or replace the controller."

ILACC-3-BADUNIT

3-Error

msgtxt_badunit

An internal software error occurred.

-

"If this message recurs contact your technical support representative."

ILACC-3-SPURIDON

3-Error

Unit [dec] spurious IDON interrupt csr[dec]=0x%04x

An Ethernet interface generated a spurious Initialization Done\n\ interrupt.

-

"Repair or replace the controller."

ILACC-3-OWNERR

3-Error

msgtxt_ownerror

An Ethernet interface is malfunctioning or an internal software error\n\ occurred.

-

"Repair or replace the controller."

MK5-1-BADRING

1-Alert

msgtxt_badringsize

An internal software error occurred.

-

"If either of these messages recur call your technical support\n\ representative for assistance."

MK5-1-NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

MK5-1-INITFAIL

1-Alert

msgtxt_initfail

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

MK5-1-INITUERR

1-Alert

Unit [dec] initialization CSR1_UERR failure csr1=0x%04x

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

MK5-1-INITNOPPRIM

1-Alert

Unit [dec] initialization failure - No CSR1_PPRIM_INIT_CONF csr1 = 0x%04x

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

MK5-3-OUTENCAP

3-Error

Unit [dec] bad output packet encapsulation: 0x[hec]

An internal software error occurred.

-

"If either of these messages recur call your technical support\n\ representative for assistance."

MK5-1-MEMERR

1-Alert

msgtxt_memoryerror

A network serial interface detected a hardware problem.

-

"Repair or replace the controller."

MK5-3-UPRIMERR

3-Error

Unit [dec] user primitive error csr0=0x%04x csr1=0x%04x

A network serial interface detected a hardware problem.

-

"Repair or replace the controller."

MK5-3-PLOSTERR

3-Error

Unit [dec] provider primitive lost csr0=0x%04x csr1=0x%04x

A network serial interface detected a hardware problem.

-

"Repair or replace the controller."

MK5-3-PPRIMERR

3-Error

Unit [dec] unexpected provider primitive csr0=0x%04x csr1=0x%04x

A network serial interface detected a hardware problem.

-

"Repair or replace the controller."

MK5-3-SPURPPRIMERR

3-Error

Unit [dec] spurious provider primitive interrupt csr0=0x%04x csr1=0x%04x

A network serial interface detected a hardware problem.

-

"Repair or replace the controller."

MK5-5-LINEFLAP

5-Notice

Unit [dec] excessive modem control changes

Too many modem control interrupts have been received. The port was\n\ disabled to prevent excessive use of the CPU.

-

"Check the cable on the serial port."

IDTATM25-1-INITFAIL

1-Alert

IDTATM25[dec]/[dec] Init failed at [chars].

The ATM25 network module hardware may be bad

pm-atm25

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-1-DISCOVER

1-Alert

Only found [dec] interfaces on bay [dec] shutting down bay

The ATM25 network module hardware may be bad

pm-atm25

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-3-NOTIDTATM25

3-Error

Device reported [hex]

The ATM25 network module hardware may be bad

pm-atm25

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-3-FAILSETUPVC

3-Error

Interface [chars] Failed to setup vc [dec] Cause: [chars]

The ATM25 network module hardware may be bad

pm-atm25

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-3-FAILTEARDOWNVC

3-Error

Interface [chars] Failed to down vc [dec] Cause: [chars]

The ATM25 network module hardware may be bad

pm-atm25

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-3-UNSUPPORTED

3-Error

Interface [chars] [chars] not supported

The ATM25 network module hardware may be bad

pm-atm25

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-6-TXLIMIT

6-Information

ATM transmit bandwidth is limited to smallest shaped value.

Any PVC configured with traffic shaping will limit the entire ATM interface to not exceed the bandwidth of any traffic shaped pvc.

-

""

IDTATM25-3-TXHANG

3-Error

IDB= [chars] TX hang Interface reset

TX hang

c1400

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IDTATM25-3-RXLOSTSYNC

3-Error

IDB= [chars] RX lost sync Interface reset

RX hang

c1400

"Copy the error message exactly as it appears and report it to your " "technical support representative."

CSM-1-INITSYS

1-Alert

[chars]

Failed to create a periodic process for CSM or the number of\n\ digit collectors reported to CSM exceeds the maximum number of\n\ digit collectors.

as

LOG_STD_ACTION

CSM-5-PRI

5-Notice

[chars] at slot [dec] unit [dec] channel [dec] with index [dec]

A PRI signalling channel is added/deleted to CSM's inventory\n\ of signalling channels.

as

"This is a notification message only.\n\ No action is required."

CSM-1-RBS

1-Alert

[chars] at slot [dec] controller [dec] timeslot [dec]

This is an internal software error. An attempt is made to add non\n\ existent CAS signalling interface.

as

LOG_STD_ACTION

CSM-1-MODEM_INFO

1-Alert

[chars]: modem_info is NULL

An internal software error occurred.

-

LOG_STD_ACTION

CSM-1-HWIDB

1-Alert

[chars]: hwidb is NULL

An internal software error occurred.

as

LOG_STD_ACTION

CSM-1-HWIDB_SUBBLOCK

1-Alert

[chars]: hwidb subblock for b channel [dec] is in use

An internal software error occurred.

as

LOG_STD_ACTION

BRI-1-NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

BRI-1-INITFAIL

1-Alert

msgtxt_initfail

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

BRI-4-NOSWITCH

4-Warning

msgtxt_initfail

ISDN leased line requires an ISDN switch type configure.

-

-

BRI-4-OVERSIZE_D_MTU

4-Warning

Failed to set MTU of [dec] on [chars]. Can't support MTU over [dec].

User config IP MTU size not supported by BRI hardware.

-

"Reconfigure IP MTU base on the suggested range."

BRI-4-OVERSIZE_B1_MTU

4-Warning

Failed to set MTU of [dec] on [chars]. Can't support MTU over [dec].

User config IP MTU size not supported by BRI hardware.

-

"Reconfigure IP MTU base on the suggested range."

BRI-4-OVERSIZE_B2_MTU

4-Warning

Failed to set MTU of [dec] on [chars]. Can't support MTU over [dec].

User config IP MTU size not supported by BRI hardware.

-

"Reconfigure IP MTU base on the suggested range."

HOOD-5-LOSTCARR

5-Notice

Unit [dec] lost carrier. Transceiver problem?

An Ethernet transceiver is unplugged or faulty.

-

"Repair or replace the controller."

HOOD-5-COLL

5-Notice

Unit [dec] excessive collisions

An Ethernet cable is broken or unterminated or the transceiver is\n\ unplugged.

-

"If the transceiver appears to be properly terminated repair or\n\ replace the router."

HOOD-3-BADUNIT

3-Error

msgtxt_badunit

An internal software error occurred.

-

"If the message recurs call your technical support representative\n\ for assistance."

HOOD-5-CABLEERR

5-Notice

Unit [dec] HP100VG cable error. Training failed

A 100VG cable or hub is faulty.

-

"If the message recurs and either the cable or hub appears to be\n\ good repair or replace the router module."

HOOD-5-NOCABLE

5-Notice

Unit [dec] HP100VG no tone detected. Check cable hub

A 100VG cable is faulty.

-

"If the message recurs and either the cable or hub appears to be \n\ good repair or replace the router module."

LES_FDDI-2-ILLEGAL

2-Critical

msgtxt_fddi_illegal

This error message is displayed when the router does not have\n\ enough I/O memory to support a FDDI interface. The FDDI interface\n\ requires at least 4MB of I/O memory.

mid-fddi

"Install the required amount of I/O memory. For maximum performance\n\ Cisco reccommends installing 8Mb of I/O memory for a single FDDI NIM\n\ and 16MB of I/O memory if 2 FDDI NIMs are installed.\n\ \n\ With 4MB of I/O memory the system will create 256 FDDI buffers for a one\n\ FDDI interface or 384 buffers for two FDDI interfaces.\n\ \n\ With 8MB of I/O memory the system will create 512 FDDI buffers for\n\ either one or two FDDI interfaces.\n\ \n\ With 16MB of I/O memory the system will create 512 FDDI buffers for\n\ a one FDDI interface or 1024 buffers for two FDDI interfaces."

HD-1-BADRING

1-Alert

msgtxt_badringsize

An internal software error occurred.

-

"If message recurs call your technical support representative for\n\ assistance."

HD-1-BADPORTADAPTER

1-Alert

4T Port Adapter fault on port [dec] in slot [dec]

A hardware or software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

HD-5-LINEFLAP

5-Notice

Unit [dec] excessive modem control changes

Too many modem control interrupts have been received. The port was\n\ disabled to prevent excessive use of the CPU.

-

"Check the cable on the serial port."

HD-1-BADLOOPCABLE

1-Alert

Loopback not supported for a 4T DTE/X.21 port [dec] in slot [dec]

Loopback mode is not allowed when using an X.21 DTE cable on a Quad\n\ serial NIM port.

-

"Do not enable loopback or use a different cable type."

SERVICE_MODULE-4-BADTYPE

4-Warning

Unit [chars] - reports incompatible module type [dec] against router hw detect

A register read request returned an identity for a module which was\n\ not the same as the identity reported by the router hardware pinout.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-OLDIMAGE

4-Warning

Unit [chars] - router image older than module version - access errors may be seen

The Cisco IOS software image does not recognize the PROM software\n\ version number on the module. The system displays this message if the\n\ PROM has been upgraded to a new version but the Cisco IOS software\n\ image has not been upgraded.

low-serial

"Upgrade the Cisco IOS software image."

SERVICE_MODULE-0-INITFAILURE

0-Emergency

Unit [chars] - failed to create data structures used for module-access

The CSU/DSU driver failed to allocate memory for its data structures.\n\ This is a catastrophic error. The system has crashed.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-0-INITWICFAILURE

0-Emergency

Unit [chars] - failed to download properly

The CSU/DSU driver detected a checksum error while downloading WIC firmware.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-REPEATEDRESET

4-Warning

Unit [chars] - giving up after [dec] repeated resets couldn't bring module up again

The software issued several clear service-module requests to the\n\ module. The module did not respond to these requests.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-5-RESET

5-Notice

Reset of Unit [chars] issued

This message indicates that the module was reset.

low-serial

"No action is required."

SERVICE_MODULE-4-RESETFAILURE

4-Warning

Unit [chars] - failed to create reset process - non-default module configuration may be lost

To execute a reset the Cisco IOS software needs to initiate a\n\ separate process. The Cisco IOS software did not have sufficient memory\n\ to create this separate process. The module came up in an initialized\n\ state with the default configuration. The user defined configuration\n\ may have been lost.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-REQUESTOVERLOAD

4-Warning

Unit [chars] - module request overload - lock access timeout

The system employs a Cisco IOS scheduler semaphore object to ensure\n\ mutually exclusive access across software threads to the CSU/DSU. This\n\ message indicates that a thread had to wait for more than 5 seconds on\n\ this semaphore.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-NOTREADY

4-Warning

Unit [chars] not ready for register access

The module was waiting for a ready status before executing a\n\ read/write request. The system reported a not ready status for 5\n\ seconds. This caused the module to terminate the read/write request.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-WICNOTREADY

4-Warning

Unit [chars] not ready for next command

The module was waiting for the current request to be processed\n\ before sending the next request. The current request has been in progress\n\ for more than 3 seconds.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-COMMANDFAILED

4-Warning

Unit [chars] not ready/responding after register [dec] access command issued

The system did not receive a ready signal within the allotted time\n\ after writing to the command register.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-INTERBYTETIMEOUT

4-Warning

Unit [chars] - timed out while [chars] byte [dec] of [dec] length register [dec]

The module took more than two seconds to respond between bytes.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-5-LOOPUPREMOTE

5-Notice

Unit [chars] - Remote unit placed in loopback

This notification message indicates that the user executed a loopback\n\ command on the remote unit. The remote unit is now in loopback.

low-serial

"No action is required."

SERVICE_MODULE-5-LOOPDOWNREMOTE

5-Notice

Unit [chars] - Remote loopback test cancelled

A hardware or software error occurred.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative for assistance."

SERVICE_MODULE-5-LOOPUPFAILED

5-Notice

Unit [chars] - Loopup of remote unit failed

This notification message indicates that the loopback on the remote\n\ unit failed. The failure may indicate that the network connection is\n\ broken or that loopbacks are disabled at the other side.

low-serial

"Check that the router is connected to the network. Enable "loopbacks"\n\ on the remote unit. If the problem persists copy the error message\n\ exactly as it appears and report it to your technical support\n\ representative."

SERVICE_MODULE-3-LOOPDOWNFAILED

3-Error

Unit [chars] - WARNING - Loopdown of remote unit failed

A remote CSU is looping pings/test patterns back to the system. This\n\ error could be triggered if the user disabled loopbacks on the remote\n\ CSU after placing the remote CSU into remote loopback.

low-serial

"Execute a clear command on the remote CSU."

SERVICE_MODULE-4-ALARMFAILURE

4-Warning

Unit [chars] - Could not access alarm status - disabling alarm processing

The system issued an alarm interrupt but could not read the alarm\n\ status register from the module. This caused the system to disable\n\ alarm processing.

low-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SERVICE_MODULE-4-UNKNOWNALARM

4-Warning

Unit [chars] reports unknown network alarms - alarm status reg = [hec]

A recent version of the module operating with an old Cisco IOS\n\ software image did not recognize an alarm condition.

low-serial

"Update the Cisco IOS software image on the system. If this does not\n\ solve the problem copy the error message exactly as it appears and\n\ report it to your technical support representative."

SERVICE_MODULE-4-ACCESSERROR

4-Warning

Unit [chars] reports register access error - [chars]

This message indicates that the T1 module supplied a bad register\n\ address. It might be due to having a new version of the module\n\ operating with an old Cisco IOS software image.

low-serial

"Update the Cisco IOS software image on the system. If this does not\n\ solve the problem copy the error message exactly as it appears and\n\ report it to your technical support representative."

HDX-3-BADFSM

3-Error

On int [dec]/[dec] unexpected state [dec] event [dec]

A bad state event pair is detected in the rx/tx half duplex state\n\ machine.

pm-fecpm

LOG_STD_ACTION

ENVMON-3-POWER_ERROR

3-Error

: [chars]

Power supply error.

cgs2520

" Make sure that the power supply connected are supported." " If the problem still persists then please contact TAC."

ENVMON-6-POWER_EXTILP

6-Information

: [chars]

External Inline Power supply info.

c1900

" Make sure that the power supply connected is supported." " If the problem still persists then please contact TAC."

ENVMON-1-POWER_WARNING

1-Alert

: [chars]

An error has occured in the power supply.

cgs2520

"Make sure that the power supply is connected to input source." "Also check if the Power Supply Unit and Redundant Power Supply" "are supported by this router." "If the problem still persists then please contact TAC."

ENVMON-5-POWER_NOTICE

5-Notice

: [chars]

Power supply notice.

cgs2520

" This is an informational message only. No action is required."

ENVMON-2-POWER_OVERTEMP_SHUTDOWN

2-Critical

Crital Warning: [chars] temperature [dec]C exceeds threshold [dec]C. The power supply will shutdown automatically if the hight temperature condition is not resolved.

Power supply temperature exceeding critial temperature threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-2-POWER_OVERTEMP

2-Critical

Warning: [chars] temperature [dec]C exceeds threshold [dec]C. Please resolve system cooling to prevent system damage

Power supply temperature exceeding threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-6-POWER_TEMP_OK

6-Information

[chars] temperature normal

The Power Supply Unit is operating at a normal temperature.

cgs2520

"The Power Supply Unit was in over-temperature level " "It is now at normal level"

ENVMON-2-FAN_TRAY_MISSING

2-Critical

Critical Warning: Fan tray was removed. Please re-insert fan tray to prevent system from overheating.

The environmental monitor can not detect fan tray on system chassis.

cgs2520

"Make sure the fan tray is properly inserted. " "If the problem persists replacement of fan tray is necessary "

ENVMON-6-FAN_TRAY_OK

6-Information

Fan tray is detected.

Fan tray previously reported as missing but it is now installed

cgs2520

"This is an informational error. No action is required."

ENVMON-2-SYSTEM_FAN_FAILED

2-Critical

Critical Warning: System Fan has failed. Please replace the fan to prevent system overheating.

System fan is not rotating.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan power connector. If problem persists " "system fan may need to be replace."

ENVMON-6-SYSTEM_FAN_OK

6-Information

Fan [dec] Functional now

Sytem fan is functioning normal now.

cgs2520

"No action is required."

ENVMON-4-ONE_FAN_LOW_RPM

4-Warning

Warning: Fan [dec] is running at low RPM. Rotation speed is now high for all other fans. Fan Tray replacement is recommended.

One of the fan is not rotating.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan power connector. If problem persists " "Pease replace system fan tray."

ENVMON-4-ONE_FAN_LOW_RPM_HDD

4-Warning

Warning: Fan [dec] is running at low RPM. Rotation speed is now high for all other fans. [chars] hard disk drive may become unusable if continuously operated at this temperature. Fan Tray replacement is recommended.

One of the fan is not rotating.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan power connector. If problem persists " "Pease replace system fan tray."

ENVMON-6-FAN_OK

6-Information

Fan [dec] is functioning normal now

Previously failed fan is functioning normal now.

cgs2520

"No action is required."

ENVMON-4-TWO_FAN_LOW_RPM

4-Warning

Warning: Two fans are running at low RPM. Rotation speed is now high for all other fans. Fan tray replacement is recommended.

Two fan failures detected.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray."

ENVMON-4-TWO_FAN_LOW_RPM_HDD

4-Warning

Warning: Two fans are running at low RPM. Rotation speed is now high for all other fans. [chars] hard disk drive may become unusable if continuously operated at this temperature. Fan tray replacement is recommended.

Two fan failures detected.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray."

ENVMON-4-MULTI_FAN_LOW_RPM

4-Warning

Critical Warning: More than two fans are running at low RPM. Rotation speed is now high for all other fans. Please replace fan tray to prevent system from overheating.

Multiple fan failures detected.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray."

ENVMON-4-MULTI_FAN_LOW_RPM_HDD

4-Warning

Critical Warning: More than two fans are running at low RPM. Rotation speed is now high for all other fans. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please replace fan tray to prevent system from overheating.

Multiple fan failures detected.

cgs2520

"Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray."

ENVMON-1-NO_PROCESS

1-Alert

Failed to create environmental monitor process

Failed to create environmental monitor process.

cgs2520

"The amount of memory available in the router may not be sufficient. " LOG_STD_ACTION

ENVMON-1-CPU_WARNING_OVERTEMP

1-Alert

Warning: CPU temperature [dec]C exceeds threshold [dec]C. Please resolve system cooling immediately to prevent system damage

System CPU temperature is over the threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-1-CPU_WARNING_OVERTEMP_HDD

1-Alert

Warning: CPU temperature [dec]C exceeds threshold [dec]C. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling immediately to prevent system damage

System CPU temperature is over the threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-2-CPU_CRITICAL_OVERTEMP

2-Critical

Critical: CPU temperature [dec]C exceeds [dec]C threshold. Please resolve system cooling immediately to prevent system damage.

System CPU temperature is over the threshold

cgs2520

"Please save system configuration and power down system " "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-2-CPU_CRITICAL_OVERTEMP_HDD

2-Critical

Critical: CPU temperature [dec]C exceeds [dec]C threshold. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling immediately to prevent system damage.

System CPU temperature is over the threshold

cgs2520

"Please save system configuration and power down system " "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-6-CPU_TEMP_OK

6-Information

CPU temperature normal

The CPU is operating at a normal temperature.

cgs2520

"The CPU previously detected an over-temperature condition " "which has now cleared. This is most likely due to high ambient " "temperature where the router is located."

ENVMON-1-CPU_CRITICAL_UNDERTEMP

1-Alert

Critical Warning: CPU temperature [dec]C is below [dec]C threshold. Please resolve operating environment temperature to prevent system damage.

System CPU temperature is below the threshold

cgs2520

"Please save system configuration and power down system " "to prevent damage causes by operational environment or faulty components." LOG_STD_ACTION

ENVMON-3-INTAKE_ABNORMTEMP

3-Error

Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system cooling.

Temperature sensor exceed abnormal temp threshold.

cgs2520

"Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-3-INTAKE_ABNORMTEMP_HDD

3-Error

Warning: [chars] Temperature [dec]C Exceeds [dec]C. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling.

Temperature sensor exceed abnormal temp threshold.

cgs2520

"Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-2-IN_OUTLET_OVERTEMP

2-Critical

Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system cooling to prevent system damage.

Temperature sensor exceed overtemp threshold.

cgs2520

"Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-2-IN_OUTLET_OVERTEMP_HDD

2-Critical

Warning: [chars] Temperature [dec]C Exceeds [dec]C. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling to prevent system damage.

Temperature sensor exceed overtemp threshold.

cgs2520

"Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-6-IN_OUTLET_TEMP_OK

6-Information

[chars] temperature normal

The inlet/outlet sensor is operating at a normal temperature.

cgs2520

"The in/outlet sensor previously detected an over-temperature condition " "which has now cleared. This is most likely due to high ambient " "temperature where the router is located."

ENVMON-2-ONBOARD_OVERTEMP

2-Critical

Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system heating to prevent system damage.

Temperature measured by sensor exceeds high temperature threshold.

cgs2520

"Please resolve system heating or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-6-ONBOARD_TEMP_OK

6-Information

[chars] temperature normal

The riser/ddr2/sfp sensors are operating at a normal temperature.

cgs2520

"The riser/ddr2/sfp sensors previously detected an over-temperature" "condition which has now cleared. This is most likely due to" "high ambient temperature where the router is located."

ENVMON-3-XFR_ENV_INIT_ERROR

3-Error

Fails to initialize MCU Environmental Control Unit

Attempt to initialize MCU Environmentcal Control Unit fails

xformers

LOG_STD_ACTION

ENVMON-1-RPS_WARNING

1-Alert

: [chars]

RPS related event notification.

cgs2520

"Make sure that the correct RPS with supported FRUs is connected" " to the router. Check if RPS FRUs are connnected to the power source." "Please refer to technical document or contact TAC for" " further clarification."

ENVMON-1-RPS_ACCESS

1-Alert

[chars]

RPS communication error detected

cgs2520

LOG_STD_ACTION

ENVMON-1-RPS_PS_MISMATCH

1-Alert

[chars]

Power supplies inserted in RPS are incompatible

cgs2520

"Remove either one of the power supplies or " "insert compatible power supplies"

ENVMON-1-RPS_FAN_FAILED

1-Alert

[chars]

RPS fan failure detected

rps

"Disconnect any routers or switches connected " "to the RPS and replace the fan immediately"

ENVMON-1-RPS_OVER_CURRENT

1-Alert

[chars]

RPS overcurrent condition detected

rps

"Unplug the routers or switches that are being " "backed off"

ENVMON-2-RPS_THERMAL_WARNING

2-Critical

RPS temperature has reached warning threshold

The temperature sensor value inside RPS has reached the warning threshold. RPS can function normally until the temperature reaches the critical threshold

rps

"The external temperature is high." " Reduce the temperature in the room"

ENVMON-1-RPS_THERMAL_CRITICAL

1-Alert

RPS temperature has reached critical threshold

The temperature sensor value inside RPS has reached the critical threshold. RPS cannot function normally

rps

"The external temperature is very high." " Reduce the temperature in the room immediately"

ENVMON-3-RPS_POST_FAILED

3-Error

[chars]

RPS POST failure detected

rps

"LOG_STD_NO_ACTION"

ENVMON-2-MODULE_OVERTEMP

2-Critical

Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system heating to prevent system damage.

Temperature measured by sensor exceeds high temperature threshold.

cgs2520

"Please resolve system heating or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION

ENVMON-6-MODULE_TEMP_OK

6-Information

[chars] temperature normal

The module card is operating at a normal temperature.

cgs2520

"The module card previously detected an over-temperature" "condition which has now cleared. This is most likely due to" "high ambient temperature where the router is located."

ENVMON-1-WARN_HDD_HIGH_TEMP

1-Alert

Critical Warning: sensor temperature [dec] C exceeds 40 C.

Ambient temperature exceeds 40 C and there is a service module with hard disk drives installed in the system. Warn user about hard disks.

c3900

"Cool down room temperature or increase air flow to the router."

ENVMON-1-WARN_HDD_FAN_HIGH

1-Alert

Warning: system temperature [dec] C is high

Fan speed has reached level3 or above and there is a service module with hard disk drives installed in the system. Warn user about hard disks.

c3900

"Resolve environmental alarm or shutdown the service module."

ENVMON-1-WARN_DOWN_REV_ROMMON

1-Alert

Warning: Router's ROMMON needs to be upgraded to suppport proper operation of module [chars]. Operation [chars] without upgrading ROMMON may cause the module hard disk driver to become unstable.

This router's ROMMON is down-rev and there is a module with hard disk drives installed in the system. Warn user about upgrading ROMMON.

c3900

"Upgrade ROMMON"

ENVMON-1-POWER_HIGH_VOLTAGE

1-Alert

Critical Warning: PSU[dec] Input Voltage [dec]V exceeds high threshold [dec]V. The system may not continue operation. Immediate operator action is required.

Power supply input voltage exceeding threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over voltage." LOG_STD_ACTION

ENVMON-1-POWER_LOW_VOLTAGE

1-Alert

Critical Warning: PSU[dec] Input Voltage [dec]V is below low threshold [dec]V. The system may not continue operation. Immediate operator action is required.

Power supply input voltage is below low threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by low voltage." LOG_STD_ACTION

ENVMON-6-POWER_VOLTAGE_OK

6-Information

PSU[dec] input voltage is normal

The Power Supply Unit input voltage is within normal limit.

cgs2520

"The Power Supply Unit input voltage was not within threshold limits " "It is now at normal level"

AMD79C971_FE-5-FAILED_SUSPEND

5-Notice

Failed to suspend the amd79c971 chip

Failed to suspend the amd79c971 chip

Mid-Ethernet

LOG_STD_ACTION

LANCE-1-INITFAIL

1-Alert

msgtxt_initfail

The hardware failed to initialize correctly.

-

"Repair or replace the controller."

LANCE-5-LATECOLL

5-Notice

Unit [dec] late collision error

An Ethernet transceiver is malfunctioning the Ethernet is overloaded\n\ or the Ethernet cable is too long.

-

"Repair or replace the controller."

LANCE-5-LOSTCARR

5-Notice

Unit [dec] lost carrier. Transceiver problem?

An Ethernet transceiver is unplugged or faulty.

-

"Repair or replace the controller."

LANCE-3-UNDERFLO

3-Error

Unit [dec] underflow error

The Ethernet hardware is requesting data faster than the system can\n\ supply it. This condition might indicate that the system is at the\n\ limit of its performance.

-

"A small number of underflows might not be a cause for concern. You can\n\ monitor underflows with the show interface command. Reducing the load\n\ on the router or installing a higher-performance router should\n\ alleviate this problem."

LANCE-5-COLL

5-Notice

Unit [dec] excessive collisions. TDR=[dec]

-

-

"If the transceiver appears to be properly terminated repair or\n\ replace the Ethernet interface card."

LANCE-1-MEMERR

1-Alert

msgtxt_memoryerror

An Ethernet interface detected a hardware problem.

-

"Repair or replace the controller."

LANCE-4-BABBLE

4-Warning

Unit [dec] babble error csr0 = 0x[hec]

An Ethernet interface is malfunctioning.

-

"Determine whether the malfunction stems from a software or hardware\n\ error by turning off all fastswitching.\n\\n\ Error messages showing that the packet is too large for the link\n\ indicate a software error at a high level.\n\\n\ Copy the error message exactly as it appears and report it to your\n\ technical support representative.\n\\n\ Receiving no error messages indicates a hardware error. \n\\n\ Repair or replace the controller."

LANCE-3-BADUNIT

3-Error

msgtxt_badunit

An internal software error occurred.

-

"If either message recurs call your technical support representative\n\ for assistance."

LANCE-3-SPURIDON

3-Error

Unit [dec] spurious IDON interrupt csr[dec]=0x%04x

An Ethernet interface generated a spurious Initialization Done\n\ interrupt.

-

"Repair or replace the controller."

LANCE-3-OWNERR

3-Error

msgtxt_ownerror

An Ethernet interface is malfunctioning or an internal software error\n\ occurred.

-

"Repair or replace the controller."

LANCE-3-BADCABLE

3-Error

msgtxt_badcable

Ethernet cable is not connected.

-

"Check Ethernet cable connection."

MAILBOX-7-ONLINE

7-Debug

[chars] mailbox coming online.

This message is generated only when mailbox debugging is enabled. It\n\ provides information about the state of each incoming or outgoing\n\ mailbox.

-

"Advisory message only. No action required."

MAILBOX-3-OFFLINE

3-Error

[chars] mailbox is offline. Interrupt ignored.

This message is generated when an attempt is made by the management\n\ module to communicate with an offline mailbox. When it appears it\n\ indicates a problem exists between the perceived state of the mailbox\n\ from the router's side versus the management module's side.

-

"Issue a system-wide reset on the management module. If the error\n\ persists call your technical support representative for assistance."

MAILBOX-3-TIMEOUT

3-Error

Intra-PDU timeout occurred on [chars] mailbox data.

A timeout occurred while sending or receiving the characters of a\n\ protocol data unit PDU. The entire PDU will be ignored.

-

"Informational message only. No action required"

MAILBOX-3-INITFAIL

3-Error

Mailbox initialization failure. [chars] Mailbox offline.

A catastrophic failure involving the initialization of the\n\ administrative mailbox occurred. The mailbox will be taken offline and\n\ remain in that state until a router module reset or a system reload\n\ occurs At that time initialization will again be attempted. Note that\n\ the functionality of the router that is it's ability to receive and\n\ forward packets is not affected by this error.

-

"Confirm the router module installation. Make sure the software\n\ revision on the management module and the router module carrier card is\n\ up-to-date. If the error persists call your technicalsupport\n\ representative for assistance."

MAILBOX-6-INITOK

6-Information

Mailbox initialization successful.

This message is generated after a router reload to indicate the\n\ mailbox was successfully initialized.

-

"Informational message only. No action required."

MAILBOX-3-BADCHKSUM

3-Error

Checksum failed. Expected = 0x%02x calculated = 0x%02x. Ignoring PDU.

A hardware or software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MAILBOX-3-BADECHO

3-Error

Echo-response did not match echo-request!

-

-

"Confirm the router module installation. Make sure the software\n\ revision on the management module and the router module carrier card is\n\ up-to-date. If the error persists call your technical support\n\ representative for assistance."

MAILBOX-3-NOECHO

3-Error

Echo-request timed out. No response received. Mailbox offline.

An ECHO_RESPONSE was not received in the appropriate time after the\n\ generation of an ECHO_REQUEST. This failure only occurs during mailbox\n\ initialization and indicates a problem between the communication path\n\ of the router module and its carrier card.

-

"Confirm the router module installation. Make sure the software\n\ revision on the management module and the router module carrier card is\n\ up-to-date. If the error persists call your technical support\n\ representative for assistance."

MAILBOX-3-BADPDU

3-Error

PDU of type [chars] received. Invalid or unsupported. Ignoring.

-

-

"Informational message only. No action required."

MAILBOX-7-WRITE

7-Debug

Writing 0x%02x to carrier.

This message is generated only when mailbox debugging is enabled. It\n\ provides very low-level information about the outgoing mailbox data\n\ stream.

-

"Advisory message only. No action required."

MAILBOX-7-READ

7-Debug

Reading 0x%02x from carrier.

This message is generated only when mailbox debugging is enabled. It\n\ provides very low-level information about the incoming mailbox data\n\ stream.

-

"Advisory message only. No action required."

MAILBOX-7-MBOXDEBUG

7-Debug

[chars]

This message header is paired with general debugging messages used to\n\ provide information about the functionality of the mailbox. To enable\n\ mailbox debugging issue the command debug mailbox.

-

"Advisory message only. No action required."

CIRRUS-1-NOMEMORY

1-Alert

msgtxt_nomemory

An operation could not be accomplished because of a low memory\n\ condition.

-

LOG_STD_REDUCE_ACTION

CIRRUS-3-BADENCAP

3-Error

msgtxt_badencap

-

-

""

CIRRUS-3-BADHDXFSM

3-Error

Interface serial [dec] Unexpected HDX state [dec] event [dec]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

CIRRUS-3-BADRXISR

3-Error

Interface serial [dec] Unexpected situation in receive ISR

An internal software error occurred while receiving data.

-

LOG_STD_SH_TECH_ACTION

CIRRUS-3-BADTXISR

3-Error

Interface serial [dec] Unexpected situation in transmit ISR

An internal software error occurred while transmitting data.

-

LOG_STD_SH_TECH_ACTION

CIRRUS-3-BADMODE

3-Error

Interface serial [dec] Bad mode encountered in init

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

CIRRUS-5-LINEFLAP

5-Notice

Unit [dec] excessive modem control changes

The specified async interface was determined to have too many\n\ automatic control changes in too short a span of time.\n\ This may indicate a hardware or software error in the interface.

-

"Reset the interface. " LOG_STD_RECUR_ACTION

CIRRUS-3-HWNORESPONSE

3-Error

The CD2430 Controller is not responding power cycle the router

The CD2430 controller has failed to respond to your request.\n\ This is due to unsupported clocking or the use\n\ of a non-standard cable.

-

"Check the clocking and cable. Use cisco cables only. " LOG_STD_RECUR_ACTION

CIRRUS-3-RESETERR

3-Error

CD2430 serial controller [dec] Reset timeout error

The async controller failed to respond to a reset command.\n\ This may indicate a hardware failure.

-

"Reset the interface or controller.\n\ Cycle the power if necessary. " LOG_STD_RECUR_ACTION

CIRRUS-3-SETCHAN

3-Error

Serial[dec]: setchan called in CD2430 interrupt context

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

CIRRUS-4-DOWNREV_NM

4-Warning

Network Module card in slot [dec] is incompatible with the system.

The network module in this slot is an old revision which is not \n\ compatible with this system. Please upgrade that network module.

-

LOG_STD_SH_TECH_ACTION

TTYDRIVER-2-NOBUF

2-Critical

Unable to allocate [dec] I/O buffers

A buffer memory shortage existed at the time that the configuration\n\ command was issued. This condition is rare and under normal\n\ conditions temporary.

-

LOG_STD_RECUR_ACTION

TTYDRIVER-2-NOBUFPOOL_ASYNC

2-Critical

Unable to create buffer pool for async. mode interface

There is not enough memory for a per channel control block\n\ of the async TTY driver.

-

LOG_STD_REDUCE_ACTION

TTYDRIVER-2-NOMEM

2-Critical

Unable to allocate [dec] byte status block

The async TTY driver was unable to create an internal structure\n\ due to a low-memory condition.

-

LOG_STD_REDUCE_ACTION

TTYDRIVER-2-NOBRKPAK

2-Critical

Unable to allocate break block from I/O mem

The router does not have enough I/O memory for buffers.

-

"Consider adding more shared memory. " LOG_STD_ACTION

DSX1-3-NOMEMORY

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_NO_TIMESLOT

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_TIMESLOT_IN_USE

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_ILLEGAL_CHANNEL

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_AR_TIMEOUT

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_AR_FAILURE

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_BAD_STATE

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_BAD_BITRATE

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_BAD_INTQ

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-3-M32_MEM_ALLOC

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-1-M32_INPUT_CONGEST

1-Alert

Munich 32 channel input queue is congested

Can't allocate receive buffers since input queue is at its maximum this indicates\n\ data is coming faster than the receiver can handle.

dsx1

"Reduce data goes into this channel and or increase the number of input queue."

DSX1-3-M32_ERR

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

DSX1-6-CLOCK_CHANGE

6-Information

[chars] clock is now selected as clock source

-

-

LOG_STD_NO_ACTION

DSX1-3-FIRMWARE_RESTART

3-Error

T1/E1 Firmware in slot [dec] restarted

T1/E1 Firmware restarted. All the active calls on the T1/E1 lines\n\ will be disconnected and the controllers will come back up within\n\ few seconds

dsx1

LOG_STD_ACTION

DSX1-1-FIRMWARE_STOPPED

1-Alert

T1/E1 Firmware in slot [dec] is not running

Critical error occurred in the T1/E1 Firmware and it stopped running. \n\ Access server needs to be reloaded.

dsx1

LOG_STD_ACTION

DSX1-1-FIRMWARE_RESTART_FAILED

1-Alert

Trunk Firmware in slot [dec] reset failed

Trunk could not be restarted.

dsx1

LOG_STD_ACTION

DSX1-1-FIRMWARE_RUNNING

1-Alert

T1/E1 Firmware in slot [dec] is running

T1/E1 Firmware is now running after recovering from critical error.

dsx1

LOG_STD_ACTION

BRIMUX-1-BADCODE

1-Alert

Software error: [chars]

An internal software error occurred.

as

LOG_STD_ACTION

BRIMUX-3-BADDPM

3-Error

Slot [dec] DPM test failed at offset 0x[hec] expect 0x[hec] read 0x[hec]

A BRIMUX board hardware problem may be present.

as

LOG_STD_ACTION

BRIMUX-3-BADDLACK

3-Error

Slot [dec] BRIC failed to acknowledge download data block [dec]

A BRIMUX firmware problem may be present.

as

LOG_STD_ACTION

BRIMUX-3-BADULREQ

3-Error

Slot [dec] BRIC failed to send upload data block [dec]

A BRIMUX firmware problem may be present.

as

LOG_STD_ACTION

BRIMUX-3-BADULBLK

3-Error

Slot [dec] BRIC wrong block [dec] for data upload expect [dec]

A BRIMUX firmware problem may be present.

as

LOG_STD_ACTION

BRIMUX-3-BADULADDR

3-Error

Slot [dec] BRIC wrong upload address received 0x[hec] requested 0x[hec]

A BRIMUX firmware problem may be present.

as

LOG_STD_ACTION

BRIMUX-3-BADULLEN

3-Error

Slot [dec] BRIC upload data length read [dec] truncate to [dec] bytes

A BRIMUX firmware problem may be present.

as

LOG_STD_ACTION

BRIMUX-3-BADBRIMUX

3-Error

Slot [dec] [chars]

A BRIMUX firmware problem may be present.

as

LOG_STD_ACTION

BRIMUX-5-UPDOWN

5-Notice

Slot [dec] BRIC changed state to [chars]

A BRIMUX board changed state.

as

LOG_STD_NO_ACTION

BRIMUX-5-PORTUPDOWN

5-Notice

BRI[dec] on slot [dec] BRIC changed state to [chars]

A port on the BRIMUX board changed state.

as

LOG_STD_NO_ACTION

BRIMUX-5-CHANUPDOWN

5-Notice

B[dec] of BRI[dec] on slot [dec] BRIC changed state to [chars]

A B-channel on the BRIMUX board changed state.

as

LOG_STD_NO_ACTION

BRIMUX-4-HEARTBEAT

4-Warning

Slot [dec] BRIC lost heartbeat for [dec] seconds

A BRIMUX board hardware or firmware problem may be present.

as

LOG_STD_RECUR_ACTION

DEC21140-5-JABBER

5-Notice

Unit [dec] jabber timeout

The transmitter for the port adapter's Fast Ethernet port has\n\ timed out and caused the transmission of a packet to fail.

-

LOG_STD_RECUR_ACTION

DEC21140-5-LOSTCARR

5-Notice

Unit [dec] lost carrier

The Fast Ethernet port lost carrier while transmitting\n\ meaning that it is no longer receiving signals from the LAN.\n\ This can be caused by disconnected Fast Ethernet cabling or\n\ a transceiver failure.

-

"If the message recurs check your Fast Ethernet cabling and port\n\ adapter first. If the problem cannot be located follow these\n\ directions. " LOG_STD_RECUR_ACTION

DEC21140-5-COLL

5-Notice

Unit [dec] excessive collisions

A Fast Ethernet packet has been dropped because too many\n\ attempts to transmit it were stopped by collisions. This can\n\ be caused by a Fast Ethernet segment which is full to capacity\n\ or by other equipment on the LAN malfunctioning.

-

LOG_STD_NO_ACTION

DEC21140-3-UNDERFLO

3-Error

Unit [dec] Tx FIFO underflow

The Fast Ethernet transmitter was ready to transmit before a packet\n\ was in the buffer. This could be caused by excessive system load.

-

LOG_STD_RECUR_ACTION

DEC21140-5-LATECOLL

5-Notice

Unit [dec] late collision error

Late collisions happen when a collision occurs after transmitting \n\ the preamble. The packet will be retransmitted but this could \n\ indicate that another device is failing to detect when the network \n\ is in use.

-

"If this recurs check for malfunctions in other devices on the \n\ Fast Ethernet."

DEC21140-5-WATCHDOG

5-Notice

Unit [dec] enormous packet received

A packet received via Fast Ethernet was dropped due to excessive \n\ size.

-

"Adjust the MTU of the interface if necessary. Otherwise\n\ no action is required."

DEC21140-3-RXFIFO

3-Error

Unit [dec] receive FIFO overflow

The Fast Ethernet receiver was unable to hand received data to a\n\ hardware buffer because the input rate exceeded the receiver's\n\ ability to handle the data. This could be caused by excessive\n\ system load.

-

LOG_STD_RECUR_ACTION

DEC21140-1-INITFAIL

1-Alert

msgtxt_initfail

The Fast Ethernet port initialization failed. This can be\n\ caused by disconnected cabling or a failure to detect the\n\ media in use.

-

"Check the cabling. Try initializing the port again. " LOG_STD_SH_TECH_ACTION

DEC21140-5-NOCARR

5-Notice

Unit [dec] no carrier

The Fast Ethernet port did not find a carrier when preparing to\n\ transmit a packet meaning that it is no longer receiving signals\n\ from the LAN. This can be caused by disconnected Fast Ethernet\n\ cabling or a transceiver failure.

-

"Check your Fast Ethernet cabling and port adapter. " LOG_STD_RECUR_ACTION

BERT-6-BERT_RESULTS

6-Information

[chars]

-

-

""

BERT-3-BERT_BAD_INTERFACE

3-Error

Interface [dec] is down BERT cannot be executed on this interface

-

-

""

BERT-3-BERT_INVPROFILE

3-Error

The Profile [dec] is not Valid

-

-

""

BERT-3-BERT_ALREADY_TEST

3-Error

A BERT is already running

-

-

""

BERT-6-BERT_START

6-Information

Starting BERT on Interface [dec] with Profile [chars]

-

-

""

BERT-3-BERT_INVPROFILE_CHANGE

3-Error

Profile [dec] currently under test cannot modify

-

-

""

BERT-3-BERT_NO_CONT

3-Error

Controller [dec] does not exist

-

-

""

BERT-6-BERT_TIMESLOTS

6-Information

No Results will be generated for this Test

-

-

""

BERT-6-BERT_FINISH_TIMESLOTS

6-Information

Finished Generation of Data for timeslots [dec] to [dec] on interface [dec] using profile [dec]

-

-

""

DSX0-5-RBSLINEUP

5-Notice

RBS of controller [dec] timeslot [dec] is up

-

-

LOG_STD_NO_ACTION

DSX0-5-RBSLINEDOWN

5-Notice

RBS of controller [dec] timeslot [dec] is down

-

-

LOG_STD_NO_ACTION

DSX0-5-RBSLINEDBUSYOUT

5-Notice

RBS of slot [dec] controller [dec] timeslot [dec] is dynamic busyout

-

-

LOG_STD_NO_ACTION

DSX0-5-RBSLINEUNBUSYOUT

5-Notice

RBS of slot [dec] controller [dec] timeslot [dec] is unbusyout

-

-

LOG_STD_NO_ACTION

DSX0-5-RBSLINESBUSYOUT

5-Notice

RBS of slot [dec] controller [dec] timeslot [dec] is static busyout

-

-

LOG_STD_NO_ACTION

FDDI-3-BADUNIT

3-Error

msgtxt_badunit

This error message is displayed when the system cannot find\n\ the chipset registers where it expects them to be.\n\ This is most likely a hardware error.

mid-fddi

LOG_STD_SH_TECH_ACTION

FDDI-1-NOMEMORY

1-Alert

msgtxt_nomemory

-

mid-fddi

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

FDDI-3-BADSLOT

3-Error

Unit [dec] Slot [dec] does not exist.

The main processor detects an invalid slot location for one of the\n\ network interface cards. This should never happen.

mid-fddi

"Call your technical support representative about obtaining a\n\ replacement card."

FDDI-3-NOCAM

3-Error

Unit [dec] No CAM exists for this interface.

A hardware or software error occurred.

mid-fddi

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

FDDI-3-FDDIFAIL

3-Error

Interface [chars] [chars] [chars] = [hex]

The FDDI interface failed.

mid-fddi

"Save the output of the error message and call your technical support\n\ representative for assistance."

FDDI-3-FDDIFAIL2

3-Error

Interface [chars] [chars] [chars] = [hex] [chars] = [hex]

The FDDI interface failed. This is the second line of the preceding\n\ FDDIFAIL message. This line contains debug information.

mid-fddi

"Save the output of the error message and call your technical support\n\ representative for assistance."

DMTDSL-3-NOMEM

3-Error

DMTDSL[dec]/[dec] Out of memory

The router does not have enough memory installed to run this image

-

LOG_STD_ACTION

DMTDSL-1-INITFAIL

1-Alert

DMTDSL[dec]/[dec] Init failed [chars]

The ADSL network module hardware may be bad

-

LOG_STD_ACTION

DMTDSL-3-FAILFINDATM

3-Error

DMTDSL Could not find ATM interface.

The DSL network module hardware may be bad

pm-atm25

LOG_STD_ACTION

DMTDSL-3-BADINITDSL

3-Error

DMTDSL[dec]/[dec]interface not initialized.

The ATM network module hardware may be bad

pm-atm25

LOG_STD_ACTION

DMTDSL-3-DMTHWBAD

3-Error

DMTDSL[dec]/[dec] Hardware failed self test

The DSL chipset failed its self test

-

LOG_STD_ACTION

CALL_MGMT-1-INITSYS

1-Alert

[chars]

The specific message text is supplied by the Call Management\n\ software. This indicates an initialization failure. When this\n\ occurs the Call Management subsystem is not operational.

-

LOG_STD_ACTION

CALL_MGMT-1-CPM_Q_POOL

1-Alert

[chars]

The specific message text is supplied by the Call Management\n\ software. This indicates a memory exhaustion condition.

-

LOG_STD_REDUCE_ACTION

CALL_MGMT-1-CALL_LIST

1-Alert

[chars]

The specific message text is supplied by the Call Management\n\ software. This indicates that internal data was corrupted\n\ due to a software error

-

LOG_STD_SH_TECH_ACTION

CALL_MGMT-4-CALL_DISC

4-Warning

[chars]

The specific message text is supplied by the Call Management\n\ software. This indicates that a call record is missing from\n\ active call list

-

LOG_STD_ACTION

LEX-3-TIMEOUT

3-Error

Retry count exceeded for [chars] : [chars]

The host router re-sent the given message as many times as specified\n\ in the lex retry-count command configuration variable without\n\ receiving an acknowledgment from the LAN Extender. At this point the\n\ host router gives up trying to send this particular remote command\n\ message.

-

"Use the LEDs on the LAN Extender to determine if it is operational.\n\ Confirm that the lex timeout configuration command is set appropriately\n\ for the speed of the link."

LEX-3-NOTSENT

3-Error

Serial line down [chars] : [chars] not sent

The serial line went down and the specified command was not sent to\n\ the LAN Extender.

-

"Determine why the serial line went down. For example was the cable\n\ was pulled or the LAN Extender powered off? The command will\n\ automatically be re-sent once the serial interface is operational."

LEX-3-RCMDNAK

3-Error

[chars] : [chars] could not be processed by LAN Extender

The LAN Extender could not process the command from the host router.\n\ Possible causes are:\n\\n\ The LAN Extender ran out of memory.\n\\n\ The message from the host router is malformed.\n\\n\ A request to write flash occurred while the LAN Extender was busy\n\ writing flash for a previous request.\n\\n\ The size of a file to be downloaded is greater than the amount of flash\n\ memory available.

-

"If the command was copy tftp lex unit-number or copy flash lex\n\ unit-number make sure that the correct file that is a FLEX image\n\ file is specified. Only a single copy request can be handled at one\n\ time. If the problem was caused by a temporary out-of-memory condition\n\ on the LAN Extender re-enter the command."

LEX-3-RCMDREJ

3-Error

[chars] : [chars] could not be processed by LAN Extender

The LAN Extender did not recognize the code for the specified remote\n\ command. This might occur if the user is running old LAN Extender\n\ software with newer host router software that has support for new LEX\n\ remote commands.

-

"Update the LAN Extender software."

LI-4-DEDICATED_MODE

4-Warning

Slot [dec] can not switch to LI dedicated mode because ther are SPAs in it.

A SIP-400 can be configured as LI dedicated service card. But it can only switch to dedicated mode if all SPAs in it are un-plugged. Otherwise it will stay in non-dedicated mode.

c7600-acl

"Un-plug all the SPAs in the SIP-400. It will automatically switch " "to LI dedicated mode."

LLC-2-UNEXPECT

2-Critical

LLC2: [chars] UNEXPECTED EVENT

An internal software error was found. A software component is trying\n\ to use LLC2 structures that do not exist.

-

"Record the configuration and any information that would be useful in\n\ recreating the error and call your technical support representative."

LLDP-4-LLDP_NEW_ENTRY

4-Warning

Neighbor record not committed - malloc failure

LLDP entry creation failed

ethernet-lldp

"Run memory diagnostics"

EPAMCM-1-NOMEMORY

1-Alert

msgtxt_nomemory

-

-

-

EPAMCM-1-INITFAIL

1-Alert

msgtxt_initfail

-

-

-

EPAMCM-0-INTERNAL_PANIC

0-Emergency

[chars]

A Panic Condition.

-

""

EPAMCM-3-INTERNAL_ERROR

3-Error

[chars]

Errors

-

""

EPAMCM-7-INTERNAL_ASSERT

7-Debug

[chars]: [chars] Assertion Failure - File [chars] Line [dec]

Assertion

-

""

EPIF_PORT-1-NOMEMORY

1-Alert

msgtxt_nomemory

-

-

-

EPIF_PORT-1-INITFAIL

1-Alert

msgtxt_initfail

-

-

-

EPIF_PORT-0-INTERNAL_PANIC

0-Emergency

[chars]

A Panic Condition.

-

""

EPIF_PORT-1-INTERNAL_ALERT

1-Alert

[chars]

A condition that should be corrected immediately.

-

""

EPIF_PORT-2-INTERNAL_CRITICAL

2-Critical

[chars]

Critical Conditions

-

""

EPIF_PORT-3-INTERNAL_ERROR

3-Error

[chars]

Errors

-

""

EPIF_PORT-4-INTERNAL_WARNING

4-Warning

[chars]

Warning

-

""

EPIF_PORT-4-INTERNAL_INTERFACE_WARNING

4-Warning

Interface [chars] [chars]

Per interface Warning

-

""

EPIF_PORT-6-INTERNAL_EVENT

6-Information

[chars]

Informational

-

""

EPIF_PORT-7-INTERNAL_ASSERT

7-Debug

[chars]: [chars] Assertion Failure - File [chars] Line [dec]

Assertion

-

""

ECODE_DOWNLOAD-1-NOMEMORY

1-Alert

msgtxt_nomemory

-

-

-

ECODE_DOWNLOAD-1-INITFAIL

1-Alert

msgtxt_initfail

-

-

-

ECODE_DOWNLOAD-0-INTERNAL_PANIC

0-Emergency

[chars]

A Panic Condition.

-

""

ECODE_DOWNLOAD-3-INTERNAL_ERROR

3-Error

[chars]

Errors

-

""

ECODE_DOWNLOAD-7-INTERNAL_ASSERT

7-Debug

[chars]: [chars] Assertion Failure - File [chars] Line [dec]

Assertion

-

""

LSS-0-INTERNAL_PANIC

0-Emergency

[chars]

A Panic Condition.

-

""

LSS-1-INTERNAL_ALERT

1-Alert

[chars]

A condition that should be corrected immediately.

-

""

LSS-2-INTERNAL_CRITICAL

2-Critical

[chars]

Critical Conditions

-

""

LSS-3-INTERNAL_ERROR

3-Error

[chars]

Errors

-

""

LSS-4-INTERNAL_WARNING

4-Warning

[chars]

Warning

-

""

LSS-4-INTERFACE

4-Warning

Interface [chars] [chars]

Per interface Warning

-

""

LSS-6-INTERNAL_EVENT

6-Information

[chars]

Informational

-

""

LSS-7-INTERNAL_ASSERT

7-Debug

[chars]: [chars] Assertion Failure - File [chars] Line [dec]

Assertion

-

""

LSS-4-LSIPC

4-Warning

[chars] [dec]

LSIPC warning - LSIPC is timing out. uCode on that interface may\n\ not be responding

E-PAM uCode

"Possibly E-PAM is not responding"

LSS-1-SDM

1-Alert

[chars] [chars]

LSS SDM Alert - protocol region reached limit. Cannot accept\n\ anymore entries. Need to reconfigure protocol regions and\n\ reload

Switching Database Manager

"Reconfigure SDM region sizes and reload"

LSS-4-MACIPC

4-Warning

[chars] [dec]

MAC Learn/Age IPC warning - MAC Learn or Age IPC dropped.\n\ The IOS bridge table and the L2 Cam entries are inconsistant

cat2948g-bridging

"Do clear bridge"

LSS-3-PORTSTUCK

3-Error

Interface [chars] is portstuck\n This port has stuck [dec] times since last boot.\n

Informational

-

"If portstuck reload is not enabled manually reload the interface or \n\ OIR the card"

LSS-3-PORTSTUCK_LIMIT

3-Error

This port has exceeded the port-stuck/\n conn-empty limit of [dec] as configured by the epc\n portstuck-reload-count command. This port will remain\n in init state until a OIR or user initiated download\n is done.\n

-

-

""

LSS-3-CHANNELSTUCK

3-Error

[chars] channel [dec] [chars] is stuck.\n This port has stuck [dec] times since last boot.\n

Informational

-

"If portstuck reload is not enabled manually reload the interface or \n\ OIR the card."

LSS-3-CONN_STATUS

3-Error

[chars] [chars]

Informational

-

""

LSS-3-CONN_PKT_STATUS

3-Error

[chars] [chars]

Informational

-

""

LSS-3-CONN_EMPTY_STATUS

3-Error

Conn empty detected [chars].\n This port has had conn empty problems [dec] times \n since last boot\n

Informational

-

"If portstuck reload is not enabled manually reload the interface or \n\ OIR the card."

LSS-4-HARDWARE_WARNING

4-Warning

\n******************************************************** \n ATM Router ModuleARM not supported with ASP hardware

Cat8510 ASP hardware with version less than 6.0 doesnot support ATM Router ModulesARM

-

"Upgrade ASP hardware version to atleast 6.0 with FC-PFQ card. "

LSS-7-VC2LEG

7-Debug

VC to LEG translation failure: vpi [dec] vci [dec]

LSS VC2LEG Alert

-

""

LSS-7-LEAFNULL

7-Debug

NUll leaf_p: vpi [dec] vci [dec]

LSS IFCB2IDB Alert

-

""

LSS-7-VC_IDB

7-Debug

Interface: [chars]

LSS VC_IDB Alert

-

""

MMODE_ISSU-2-INIT

2-Critical

MMODE ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MMODE ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

polaris-gir

LOG_STD_ACTION

MMODE_ISSU-3-TRANSFORM_FAIL

3-Error

MMODE ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MMODE ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MMODE state between the active device and the standby device is not identical.

polaris-gir

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MMODE_ISSU-3-MSG_NOT_OK

3-Error

MMODE ISSU client 'Message Type [dec]' is not compatible

The MMODE ISSU client received an incompatible message from the peer device. The message cannot be processed.

polaris-gir

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MMODE_ISSU-3-MSG_SIZE

3-Error

MMODE ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MMODE ISSU client failed to calculate the MTU for the specified message. The MMODE ISSU client is not able to send the message to the standby device.

polaris-gir

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MMODE_ISSU-3-INVALID_SESSION

3-Error

MMODE ISSU client does not have a valid registered session.

The MMODE ISSU client does not have a valid registered session.

polaris-gir

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-2-SESSION_REGISTRY

2-Critical

MMODE ISSU client failed to register session information. Error: [dec] [chars]

The MMODE ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

polaris-gir

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-3-SESSION_UNREGISTRY

3-Error

MMODE ISSU client failed to unregister session information. Error: [dec] [chars]

The MMODE ISSU client failed to unregister session information.

polaris-gir

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-2-SESSION_NEGO

2-Critical

MMODE ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MMODE ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

polaris-gir

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-2-SEND_NEGO_FAILED

2-Critical

MMODE ISSU client failed to send negotiation message. Error: [dec] [chars]

The MMODE ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

polaris-gir

"show logging and show checkpoint client"

MMODE_ISSU-2-SESSION_ARBITRATE

2-Critical

MMODE ISSU client failed to register arbitrate callback. Error: [dec] [chars]

The MMODE ISSU client failed to register arbitrate callback. If a problem occurs with the callback registration the standby device cannot be brought up properly.

polaris-gir

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-2-GET_BUFFER

2-Critical

MMODE ISSU client failed to get buffer for message. Error: [dec] [chars]

MMODE ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

polaris-gir

"show logging and show checkpoint client"

MMODE_ISSU-3-INVALID_CAPABILITY

3-Error

MMODE ISSU client: invalid capability list

MMODE ISSU client observed an error during capability negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

polaris-gir

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-3-REJECTED_CAPABILITY

3-Error

MMODE ISSU client rejected capability '[chars]'

MMODE ISSU client rejected a capability during negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

polaris-gir

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-3-REJECTING_CAPABILITY

3-Error

MMODE ISSU client rejecting capability '[chars]'

MMODE ISSU client is rejecting a capability during negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

polaris-gir

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MMODE_ISSU-3-POLICY_NOT_SUPPORTED

3-Error

MMODE ISSU client does not support Message Type [dec]

MMODE ISSU client received an message type which it does not support. The policy is applied to make the session incompatible.

polaris-gir

"show issu session <client_id>"

MMODE-3-MMODE_CLIENT_TRANSITION_FAILED

3-Error

Maintenance failed to [chars] client [chars]

This message will be seen if client returns nack.

polaris-gir

-

MMODE-3-MMODE_CLASS_TRANSITION_TIMED_OUT

3-Error

Maintenance failed to [chars] class [chars] due to timeout

This message will be seen if client fails to finish transition.

polaris-gir

"Use Show system mode maintenance clients to \n\ find which clients failed."

MMODE-6-MMODE_CLIENT_TRANSITION_START

6-Information

Maintenance [chars] start for [chars]

This message will be seen if client starts transition.

polaris-gir

-

MMODE-6-MMODE_CLIENT_TRANSITION_COMPLETE

6-Information

Maintenance [chars] complete for [chars]

This message will be seen if client completes transition.

polaris-gir

-

MMODE-6-MMODE_CLIENT_NOT_FOUND

6-Information

Maintenance client [chars] not found

This message will be seen if client listed in template sequence\n\ but not registered.

polaris-gir

-

MMODE-6-MMODE_ISOLATED

6-Information

System is in Maintenance

This message will be seen if maintenance mode intitated\n\ by operator is successful.

-

-

MMODE-6-MMODE_INSERTED

6-Information

System is in Normal Mode

This message will be seen if system comes out of maintenance\n\ successfully by operator issued command or maintenance window is over.

-

-

MMODE-6-MMODE_SNAPSHOT_CREATE_ENTER_MMODE

6-Information

Generating current snapshot 'before_maintenance'

This message will be seen for a snapshot created before entering mmode.

polaris-gir

-

MMODE-6-MMODE_SNAPSHOT_CREATE_EXIT_MMODE

6-Information

Generating current snapshot 'after_maintenance' \n\nPlease use 'show system snapshots compare before_maintenance after_maintenance' to check the health of the system

This message will be seen for a snapshot created before exiting mmode.

polaris-gir

-

DLEP_MSG-4-CONNECT_ERROR

4-Warning

TCP connect to Radio [inet] failed via [chars]. Error code: [chars]

TCP Connect to IP address and port of the Radio failed.

DLEP_DDTS_COMPONENT

"Take action based on the error code shown." " Reconfigure correct IP address and port " " if necessary."

DLEP_SET_MSG-6-DLEP_HEARTBEAT_THRESHOLD

6-Information

new Threshold value configured will have effect for the new sessions only not for the currently running DLEP sessions

If the threshold value should be updated at Router side it must be configured before the Radio launch

dlep

"Once the DLEP session is established and if you" " want to change the threshold value kill the" " Radio and reconfigure the dlep on Router" " interface and make the Radio UP to see" " the updated threshold value "

DLEP_SET_MSG-6-DLEP_NBR_ACTIVITY_TIMEOUT

6-Information

new nbr-activity-timeout value configured will have effect for the new sessions only not for the currently running DLEP sessions

If the nbr-activity-timeout value should be updated at Router side it must be configured before the Radio launch

dlep

"Once the DLEP session is established and if you" " want to change the nbr-activity-timeout value" " kill the Radio and reconfigure the dlep on" " Router interface and make the Radio UP to see" " the updated value "

DLEP_SET_MSG-6-DLEP_NBR_DOWN_ACK_TIMEOUT

6-Information

new nbr-down-ack-timeout value configured will have effect for the new sessions only not for the currently running DLEP sessions

If the nbr-down-ack-timeout value should be updated at Router sideit must be configured before the Radio launch

dlep

"Once the DLEP session is established and if you want" " to change the nbr-down-ack-timeout value kill the " "Radio and reconfigure the dlep on Router interface " "and make the Radio UP to see the updated Value "

DLEP_SET_MSG-6-DLEP_PEER_TERMINATE_ACK_TIMEOUT

6-Information

new peer-terminate-ack-timeout value configured will have effect for the new sessions only not for the currently running DLEP sessions

If the peer-terminate-ack-timeout value should be updated Router side it must be configured before the Radio launch

dlep

"Once the DLEP session is established and if you want" " to change the peer-terminate-ack-timeout value" " kill the Radio and reconfigure the dlep on Router" " interface and make the Radio UP to see the updated value "

ASR1000_PTP-3-MSGINITFAIL

3-Error

Failed to initalize required PTP resource: [chars]

During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated.

asr1000-ptp

LOG_STD_ACTION

ASR1000_PTP-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message from PTP daemon [chars] - [chars]

An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from PTP daemon.

asr1000-ptp

LOG_STD_ACTION

ASR1000_PTP-3-FPGA_VER_ERR

3-Error

Please consider upgrading the FPGA for PTP to function properly. [chars] 0x[hec]

Router is currently running on FPGA version which is lesser than what is required by PTP to work properly

asr1000-ptp

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-6-MSGUNEXPECTEDEVENT

6-Information

Unexpected event recieved.

When a diagnostic test is performed IOS waits for the result\n\ be returned. While waiting for the result IOS unexpectedly\n\ received an event it does not recognize and so IOS stopped\n\ waiting for the result. The test continued IOS does not know\n\ what the results are and hence can not report them.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-6-MSGOUTOFORDER

6-Information

Received a test result after IOS had timed out. [[dec][dec]]

When a diagnostic test is performed IOS waits for the result \n\ be returned. If it does not return in a specified period of \n\ IOS times out on that test request and moves on.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-3-MSGTDLERROR

3-Error

Error processing TDL message. [dec]

An unexpected condition in which IOS has received a TDL \n\ message which it can not process.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-3-MSGOBJNULL

3-Error

An unexpected condition in which IOS has received a null\n\ pointer that it expects to be non-null.

An unexpected condition has occurred while IOS is trying to perform \n\ online diagnostics work.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-3-MSGDIAGCANTENQUEUE

3-Error

Online diagnostics could not enqueue a diagnostic test response.

The iosxe online diagnostics failed to respond properly to a \n\ request by the system to perform a diagnostic test.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-3-MSGDIAGTIMEOUT

3-Error

A timeout occured while waiting for an online diagnostic \n\ test to finish.

The iosxe online diagnostics failed to respond properly to a \n\ request by the system to perform a diagnostic test.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-3-MSGRESPTDLERR

3-Error

A diagnostic test result could not be read properly.

The iosxe online diagnostics failed to respond properly to a \n\ request by the system to perform a diagnostic test.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-3-MSGIPCTXERROR

3-Error

IPC transmit error. [dec]

An unexpected condition in which IOS encountered an error \n\ trying to send a message to another process. [dec]

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-4-ERR_CNTR_HM_TEST_DATA

4-Warning

ERROR_COUNTER_DATA: ID:[dec] IN:%D PO:[dec] RE:[dec] RM:[dec] DV:[dec] EG:[dec] CF:[dec] TF:[dec]

Error Counter Monitoring test has failed on one of the cards of IOSXE Corresponding Data is printed.

iosxe-sch-gold

LOG_STD_ACTION

IOSXE_RP_DIAG_TEST-4-ERR_CNTR_HM_TEST_FAIL

4-Warning

ERROR_COUNTER_WARNING: Slot [chars] Error counter exceeds threshold system operation continue.

Error Counter Monitoring test has failed on the given card of IOSXE.

iosxe-sch-gold

LOG_STD_ACTION

IOSXE_RP_ONLINE_DIAG-3-MSGMAXCARDS

3-Error

Online diagnostics maximum number of cards exceeded

An unexpected condition in which IOS has attempted to \n\ register more hardware cards for diagnostics than it\n\ expects the maximum to be.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_ONLINE_DIAG-3-MSGTDLERROR

3-Error

Error processing TDL message. [dec]

An unexpected condition in which IOS has received a TDL\n\ message which it can not process.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_RP_ONLINE_DIAG-3-MSGOBJNULL

3-Error

An unexpected condition in which IOS has received a null\n\ pointer that it expects to be non-null.

An unexpected condition has occurred while IOS is trying to perform\n\ online diagnostics work.

iosxe-chassismgr

LOG_STD_ACTION

CMANCC-3-MSGDISPATCH

3-Error

Unable to dispatch received message from Chassis Manager

An unexpected condition has occurred while IOS was trying to dispatch\n\ a message received from the Chassis Manager.

iosxe-chassismgr

"Verify that all local components are in the proper operational state.\n\ If any inconsistency is found it may be corrected by offlinine and\n\ restart of the effected component SPA Carrier Card"

CMANCC-3-MSGIPCERR

3-Error

Unable to process received IPC messages from Chassis Manager\n\ error: [chars]

An unexpected condition has occurred while IOS trying to process a\n\ received IPC message from Chassis Manager.

iosxe-chassismgr

LOG_STD_ACTION

CMANCC-2-CRASHDUMP

2-Critical

Fatal error calling crashdump error: [dec] [chars]

A fatal condition has occurred causing IOS to crashdump. IOS will\n\ be restarted automatically.

iosxe-chassismgr

LOG_STD_ACTION

CMANCC-3-UNEXPECTEDEVENT

3-Error

UDI Auth Process received unknown event maj [hec] min [hec].

UDI auth process has registered to be notified when a process \n\ boolean change event occurs in the router. This message indicates \n\ that this process received an event it did not know how to handle.

iosxe-chassismgr

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

IOSXE_SIP_SPA-3-HWIDB_FAILURE

3-Error

Creation: port [dec] vc [dec]

Failed to create a hwidb.

asr1k-spa-infra

LOG_STD_SH_TECH_ACTION

IOSXE_SIP_SPA-3-DEVICE_ERROR

3-Error

subSlot [dec] spatype 0x[hec]. Device error: [chars]

An error related to a device on the SPA is detected.

asr1k-spa-infra

LOG_STD_SH_TECH_ACTION

IOSXE_SIP_SPA-3-ISR_RC_ERROR

3-Error

ISR return code out of range. rc=[dec]

The ISR error return code is out of range.

asr1k-spa-infra

LOG_STD_SH_TECH_ACTION

IOSXE_SIP_SPA-3-SPA_INTF_ID_CC_ALLOC_FAILED

3-Error

Failed to allocate interface identifiers for SPA [chars]

Failed to get CC buffer and flow control identifiers for the SPA in the specified subslot Traffic cannot flow through the SPA under this failure condition. This can happen if the system runs out of available identifiers.

asr1k-spa-infra

"Try to reduce the number of interfaces" "configured in the system either by physically removing the SPAs" "or by changing the system configuration"

IOSXE_SIP_SPA-4-SPABUS

4-Warning

Subslot [dec] [chars] SPA BUS access failed. timeout=[dec] err=[dec] par=[dec] err_c=0x[hec] addr=0x%08x data =0x[hec]

SPABUS has reported an error.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-4-SPABUS2

4-Warning

Subslot [dec] SPA BUS access failed. No SPA present error

SPABUS has reported an error.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-6-OIR

6-Information

Bay [dec] [chars] changed to [chars]

SPA OIR Sequence

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-4-MAX_BANDWIDTH

4-Warning

Total SPA bandwidth exceeds line card capacity of %lu Mbps

The total bandwidth of SPAs exceeds the rated capacity of this line card.

asr1k-spa-infra

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

IOSXE_SIP_SPA-4-MAX_BANDWIDTH_NS

4-Warning

Total SPA bandwidth exceeds line card capacity full utilization of installed SPA interfaces is not supported

The total bandwidth of SPAs exceeds the rated capacity of this line card.

asr1k-spa-infra

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

IOSXE_SIP_SPA-3-POWER

3-Error

Bay [dec] 12V power is [chars]

SPA 12V power fault indicator

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-SPI4_INIT_FAILURE

3-Error

Bay [dec] initialization failure

Failed to create SPI4 subblock

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOSXE_SIP_SPA-3-MESSAGE_ERROR

3-Error

Bay [dec]: [chars]

An unexpected error has occurred.

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOSXE_SIP_SPA-3-SPI4_CONFIG_FAILURE

3-Error

Bay [dec] spi4 configuration failure error [dec]

Failed to configure SPI4 interface

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOSXE_SIP_SPA-3-SPI4_NOTSYNC

3-Error

[chars]: Can not synchronize SPI4 bus host: src [chars]in sync sink [chars]in sync spa: src [chars]in sync sink [chars]in sync.

SPI4 bus between modular services card and SPA is not synchronized. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image.

-

"Ensure that the SPA is properly seated " "in its subslot and reseat it if required."

IOSXE_SIP_SPA-3-SPA_CTRL_INIT_FAILURE

3-Error

Subslot [dec] spa controller initialisation failure error [dec]

Failed to initialise SPA controller

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOSXE_SIP_SPA-3-SPA_CTRL_EFC_CONFIG_FAILURE

3-Error

Subslot spa controller EFC configuration failure error [dec]

Failed to configure SPA controller EFC

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOSXE_SIP_SPA-3-FCI_NOT_SET

3-Error

Bay [dec] - FCI type not set

An FCI type of zero was detected

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-EFC_CHAN_ERR

3-Error

EFC error - interface [chars] vc [dec] anyphy [dec] err_code [dec] : [chars]

Failed to configure efc channel/parameters

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOSXE_SIP_SPA-3-INVALID_ANYPHY

3-Error

Bay [dec] - Invalid anyphy number [dec] for vc [dec]

Interface has invalid anyphy mumber

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

IOSXE_SIP_SPA-3-LINKREC_ERROR

3-Error

Link record error - Bay [dec] vc [dec] error code [dec]

Error processing link record structure

asr1k-spa-infra

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

IOSXE_SIP_SPA-3-SONET_CLOCK_FAILED

3-Error

SPA Sonet clock has failed status = 0x%08x

The SPA SONET clock has failed. SPAs that rely on the SPA SONET clock for proper operation such as POS and ATM will be affected.

asr1k-spa-infra

"If the SPA Sonet clock does not recover perform an " "OIR. "LOG_STD_RECUR_ACTION

IOSXE_SIP_SPA-3-SONET_CLOCK_RECOVERED

3-Error

SPA Sonet clock has recovered status = 0x%08x

SPA Sonet clock has recovered

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-INVALID_IF

3-Error

Attempted to access HWIDB for port [dec] on slot [dec] subSlot [dec]

The ASR1000 attempted to access the HWIDB associated with\n\ a non-existent port.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-ASR1000IPCALLOCFAIL

3-Error

Failed to allocate Common IPC buffer [chars]

The Carrier Card failed to allocate a buffer for\n\ communication with the Route Processor.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-CMDNOINT

3-Error

HWIDB Null for command [dec] port [hex]

The Route Processor passed down a port number that is unknown on the\n\ carrier card.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-EFC_FC_MAP_FAIL

3-Error

Failed to update EFC flow control identifier for interface [chars] status = [dec]

The SPA driver is not able to update the datapath EFC flow control identifier for the interface specified in the message. This indicates a hardware error.

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-EFC_PROV_FAIL

3-Error

Failed to provision EFC for interface [chars] status = [dec]

The SPA driver is not able to provision EFC for the interface specified in the message. This indicates a hardware error.

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-EFC_UNPROV_FAIL

3-Error

Failed to unprovision EFC for VC [chars] status = [dec]

The SPA driver is not able to unprovision EFC for the interface specified in the message. This indicates a hardware error.

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-C2W_MAIN_INIT_FAIL

3-Error

Failed to initialize SPA main c2w bus for subslot [dec] status = [dec]

The SPA driver is not able to initialize SPA main c2w. This indicates a hardware error.

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-NETCLK_FAIL

3-Error

Failed to [chars] SPA reference clock on [chars]

The SPA driver is not able to correctly configure the SPA reference clock on the specified interface. This indicates a hardware error.

asr1k-spa-infra

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-LVLTRTOOBIG

3-Error

Loveletter length exceeds max [dec] bytes

The ASR1000-SIP line card attempted to send a large message to the\n\ Route Processor ASR1000-RP.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-NODISPATCH

3-Error

Dispatch vector Null cmd=[dec] dintf=[dec]

No command dispatch vector was found for the specified interface.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-BADMALUCMD2

3-Error

Unsupported MALU cmd/arg0=0x%04x%04x arg1arg2=0x%04x%04x hwidb=[chars]

-

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-BADMALUCMD

3-Error

Unsupported MALU command [dec] arg=[hex] pascb=[hex]

-

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-BAD_IFCOMTYPE

3-Error

Bad ifcom message type=[dec]

-

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The Linecard failed to send a message to the\n\ Route Processor ASR1000-RP.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The SPA failed to allocate a buffer for communication with\n\ the Route Processor ASR1000-RP.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-IPCPORTFAIL

3-Error

Failed to open IPC port '[chars]' [chars] with error [chars]

The RP failed to open a port for communication with a SPA\n\ module.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-IPCPORT

3-Error

Failed to [chars] IPC port '[chars]' error [chars]

The Linecard failed to create a port for\n\ communication with the Route Processor ASR1000-RP.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-FAST_NOTIFY_ERROR

3-Error

Failed to send fast notification to [chars] for [chars] [chars].

The SPA driver failed to deliver a fast notification.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-6-LOGGERMSGTOOBIG

6-Information

Logger message length [dec] bytes exceeds the maximum allowed size

The carrier card attempted to send a large message to the Route Processor

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-FRR_CFG_FAIL

3-Error

Failed to configure fast reroute on [chars]: [chars].

The SPA driver failed to configure fast rerouting on an interface.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-APS_CFG_FAIL

3-Error

Failed to configure APS on [chars]: [chars].

The SPA driver failed to configure APS on an interface.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-APS_PGP_FAIL

3-Error

APS PGP Message send failed toslot/tobay [dec]: [dec].

The SPA ETHER process is not able to write to ezman as ezman is blocked for writes. Copy the error message exactly as it appears and report it to your technical support representative.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_IMCC_CAPI-3-MSGDISPATCHNULL

3-Error

Received NULL TDL message from IOS

An unexpected condition in which IOSD has received a NULL TDL \n\ message from Interface Manager.

iosxe-intfmgr

LOG_STD_ACTION

IOSXE_IMCC_CAPI-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message name = [chars] from

An unexpected condition has occurred while IOS is trying to dispatch\n\ to the TDL message handler functions for received TDL messages from \n\ Interface Manager.

iosxe-intfmgr

LOG_STD_ACTION

IOSXE_IMCC_CAPI-3-MSGIPCERR

3-Error

Unable to process received IPC messages from Interface Manager\n\ error: [chars]

An unexpected condition has occurred while IOS trying to process a\n\ received IPC message from Interface Manager.

iosxe-intfmgr

LOG_STD_ACTION

IOSXE_IMCC_CAPI-2-CRASHDUMP

2-Critical

Fatal error calling crashdump error: [dec] [chars]

A fatal condition has occurred causing IOS to crashdump.

iosxe-intfmgr

LOG_STD_ACTION

IOSXE_IMCC_CAPI-6-CMSTATUS

6-Information

Interface Manager Process is [chars]

The current status of Interface Manager Process.

-

LOG_STD_NO_ACTION

NGWC_OBFL-5-DISABLED

5-Notice

[chars] Onboard Failure Logging disabled on switch [dec]

Onboard Failure Logging has been disabled

obfl

LOG_STD_NO_ACTION

PLATFORM_IE9K-3-PORT_NOT_OPERATING

3-Error

[chars] [chars] [chars] [chars]

The port is not operating the startup selftest has failed

-

LOG_STD_ACTION

PLATFORM_IE9K-3-PORT_NOT_FORWARDING

3-Error

[chars] [chars] [chars] [chars]

The port is not forwarding the startup selftest has failed

-

LOG_STD_ACTION

PLATFORM_IE9K-3-FCS_ERROR

3-Error

[chars] [chars] [chars] [chars]

The port fcs error threshold max has reached

-

LOG_STD_ACTION

PLATFORM_IE9K-3-PORT_LINK_FAULT

3-Error

[chars] [chars] [chars] [chars]

The port link is not coming up the startup selftest has failed

-

LOG_STD_ACTION

PLATFORM_IE9K-5-PORT_FAST_RETRAIN

5-Notice

Port link fast-retraining has happened for [chars]

The port link fast-retraining has happened for [chars]

-

LOG_STD_NO_ACTION

ENVIRONMENT-4-SECONDARY_UNDERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the configured min temperature \n\ threshold but less or equal to the max inside temperature

-

-

ENVIRONMENT-4-SECONDARY_OVERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the configured threshold\n\ but less or equal to the max inside temperature

-

-

ENVIRONMENT-3-OVERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the max temperature threshold

-

-

ENVIRONMENT-3-UNDERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the min temperature threshold

-

-

ENVIRONMENT-3-RPS_FAILED

3-Error

[chars] [chars] [chars] [chars]

Only one power supply was detected for system in dual power mode or\n\ power supply is failing

-

-

ENVIRONMENT-3-SD_CARD

3-Error

[chars] [chars] [chars] [chars]

SD card is not present

-

-

ENVIRONMENT-3-SD_CARD_UNSUPPORTED

3-Error

[chars] [chars] [chars] [chars]

SD card is not supported

-

-

ENVIRONMENT-3-SD_CARD_CORRUPT

3-Error

[chars] [chars] [chars] [chars]

SD card is corrupted

-

-

ENVIRONMENT-3-SD_CARD_FILES_CORRUPT

3-Error

[chars] [chars] [chars] [chars]

Image File on SD card is corrupted

-

-

ENVIRONMENT-3-SD_CARD_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

SD card is not present. Image booted from on-board flash.

-

-

ENVIRONMENT-3-SD_CARD_UNSUPPORTED_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

SD card is not supported. Image booted from on-board flash.

-

-

ENVIRONMENT-3-SD_CARD_CORRUPT_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

SD card is corrupted. Image booted from on-board flash.

-

-

ENVIRONMENT-3-SD_CARD_FILES_CORRUPT_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

Image File on SD card is corrupted. Image booted from on-board flash.

-

-

ENVIRONMENT-3-LIC_FILE_CORRUPT

3-Error

[chars] [chars] [chars] [chars]

License file is corrupted

-

-

ENVIRONMENT-3-AC1_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 1 triggered

-

-

ENVIRONMENT-3-AC2_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 2 triggered

-

-

ENVIRONMENT-3-AC3_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 3 triggered

-

-

ENVIRONMENT-3-AC4_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 4 triggered

-

-

ENVIRONMENT-3-POWER_ERROR

3-Error

[chars]

Power supply error.

-

" Make sure that the power supply connected are supported." " If the problem still persists then please contact TAC."

PLATFORM_ENV-1-EXTERNAL_ALARM_CONTACT_ASSERT

1-Alert

Alarm asserted: [chars]

Error condition detected on external alarm contact

hardware

LOG_STD_ACTION

PLATFORM_ENV-1-EXTERNAL_ALARM_CONTACT_CLEAR

1-Alert

Alarm cleared: [chars]

Error condition cleared on external alarm contact

hardware

LOG_STD_ACTION

POWER_SUPPLIES-3-PWR_A_FAIL

3-Error

Power supply A is not functioning

Power supply A is present but not functioning

hardware

LOG_STD_ACTION

POWER_SUPPLIES-3-PWR_B_FAIL

3-Error

Power supply B is not functioning

Power supply B is present but not functioning

hardware

LOG_STD_ACTION

POWER_SUPPLIES-5-PWR_A_OK

5-Notice

Power supply A is functioning

Power supply A is supplying power

hardware

LOG_STD_NO_ACTION

POWER_SUPPLIES-5-PWR_B_OK

5-Notice

Power supply B is functioning

Power supply B is supplying power

hardware

LOG_STD_NO_ACTION

POWER_SUPPLIES-3-PWR_FAIL

3-Error

Power supply [chars] is not functioning

Power supply is present but not functioning

hardware

LOG_STD_ACTION

POWER_SUPPLIES-5-PWR_OK

5-Notice

Power supply [chars] is functioning

Power supply is supplying power

hardware

LOG_STD_NO_ACTION

NGWC_ILP_ISSU-3-INIT

3-Error

Platform Inline Power ISSU client initialization failed at [chars] error [chars]

Platform Inline Power ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_ILP_ISSU-3-TRANSFORM

3-Error

Platform Inline Power ISSU client [chars] transform failed error [chars]

Platform Inline Power ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Platform Inline Power state will not\n\ be indentical with the active unit.

platform-ha

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NGWC_ILP_ISSU-3-MSG_NOT_OK

3-Error

Platform Inline Power ISSU client message [dec] is not compatible

Platform Inline Power ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NGWC_ILP_ISSU-3-MSG_SIZE

3-Error

Platform Inline Power ISSU client failed to get the message size for message [dec]

Platform Inline Power ISSU client failed to calculate message size\n\ for the message specified. The Platform Inline Power ISSU client will not\n\ be able to send message to the standby unit.

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NGWC_ILP_ISSU-3-SESSION

3-Error

Platform Inline Power ISSU client [chars]

Platform Inline Power ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

NGWC_ILP_ISSU-3-SESSION_UNREGISTRY

3-Error

Platform Inline Power ISSU client failed to unregister session information. Error: [dec] [chars]

The Platform Inline Power ISSU client failed to unregister session information.

platform-ha

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

NGWC_ILP_ISSU-3-SEND_FAILED

3-Error

Platform Inline Power ISSU client failed to send a negotiation message error [dec]

Platform Inline Power ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

NGWC_ILP_ISSU-3-BUFFER

3-Error

Platform Inline Power ISSU client failed to get buffer for message error [dec]

Platform Inline Power ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

NGWC_ILP_ISSU-3-CAPABILITY

3-Error

Platform Inline Power ISSU client [chars]

Platform Inline Power ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

NGWC_ILP_ISSU-3-POLICY

3-Error

Platform Inline Power ISSU client message type [dec] is [chars]

Platform Inline Power ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

platform-ha

"show issu session <client_id>"

NGWC_ILP_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

Platform Inline Power ISSU client capability exchange result incompatible.

The Platform Inline Power ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

platform-ha

"show issu negotiated capability <Session_ID>"

NGWC_ILP_ISSU-3-CAP_INVALID_SIZE

3-Error

Platform Inline Power ISSU client capability list is empty.

The Platform Inline Power ISSU client capability exchange list size\n\ is invalid.

platform-ha

"show issu capability entries <Client_ID>"

PLATFORM_ENV-6-RPS_PRESENCE

6-Information

Redundant Power SupplyRPS [chars]

Redundant Power Supply RPS changed state

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-6-RPS

6-Information

Redundant Power SupplyRPS [chars]

-

-

-

PLATFORM_ENV-3-RPS_FAULTY_BACKUP

3-Error

[chars]

RPS error condition detected

firmware

"This problem could be transient. If fault " "persists remove and reconnect the switch"

PLATFORM_ENV-1-RPS_STANDBY

1-Alert

[chars]

Faulty RPS detected

firmware

LOG_STD_ACTION

PLATFORM_ENV-1-RPS_ACCESS

1-Alert

[chars]

RPS communication error detected

firmware

LOG_STD_ACTION

PLATFORM_ENV-6-RPS_INFO

6-Information

Redundant Power Supply [chars]

Related info about RPS

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-2-RPS_THERMAL_WARNING

2-Critical

RPS temperature has reached warning threshold

The temperature sensor value inside RPS has reached the warning threshold. RPS can function normally until the temperature reaches the critical threshold

hardware

"The external temperature is high." " Reduce the temperature in the room"

PLATFORM_ENV-1-RPS_THERMAL_CRITICAL

1-Alert

RPS temperature has reached critical threshold

The temperature sensor value inside RPS has reached the critical threshold. RPS cannot function normally

hardware

"The external temperature is very high." " Reduce the temperature in the room immediately"

PLATFORM_ENV-5-RPS_THERMAL_NORMAL

5-Notice

RPS temperature is within the acceptable limit

The temperature sensor value inside RPS is within the normal limit

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-RPS_PS_THERMAL_CRITICAL

1-Alert

RPS power supply [chars] temperature has reached critical threshold

The power supply inside RPS has reached the critical threshold. RPS cannot function normally

hardware

"The external temperature is very high." " Reduce the temperature in the room immediately"

PLATFORM_ENV-1-RPS_PS_FAN_FAILED

1-Alert

RPS power supply [chars] fan failure detected

RPS power supply fan failure has been detected

hardware

"Disconnect any switches connected to the RPS and " "replace the power supply immediately"

PLATFORM_ENV-1-RPS_PS_SIGNAL_FAULTY

1-Alert

[chars] signal on RPS power supply [chars] is faulty

The specified power supply of RPS has faulty signal

hardware

LOG_STD_ACTION

PLATFORM_ENV-1-RPS_BACKING_UP_INFO

1-Alert

[chars] [dec]

This event indicates RPS is backing up power to port

hardware

LOG_STD_ACTION

PLATFORM_ENV-1-RPS_BACKING_OFF_INFO

1-Alert

[chars] [dec]

This event indicates RPS is backoff power from port

hardware

LOG_STD_ACTION

PLATFORM_ENV-3-RPS_BACKOFF_FAILED

3-Error

[chars]

RPS is continuing to backup switch even though switch issued a command to backoff

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-RPS_PS_MISMATCH

1-Alert

[chars]

Power supplies inserted in RPS are incompatible

firmware

"Remove either one of the power supplies or " "insert compatible power supplies"

PLATFORM_ENV-1-RPS_FAN_FAILED

1-Alert

[chars]

RPS fan failure detected

hardware

"Disconnect any switches connected to the RPS and " "replace the fan immediately"

PLATFORM_ENV-1-RPS_OVER_CURRENT

1-Alert

[chars]

RPS overcurrent condition detected

hardware

"Unplug the switches that are being backed off"

PLATFORM_ENV-6-RPS_PS_INSERTED

6-Information

[chars]

Power supply inserted in RPS

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-6-RPS_PS_REMOVED

6-Information

[chars]

Power supply removed from RPS

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-3-RPS_CHANGE_TO_STANDBY

3-Error

[chars]

RPS has changed state to standby. It will no longer backup the switch

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-1-RPS_SYS_POWER_GOOD

1-Alert

[chars]

RPS system power changed state to good

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-1-RPS_SYS_POWER_BAD

1-Alert

[chars]

RPS system power changed state to bad. It may not provide backup

hardware

"Check the power supplies in RPS. If fault " "persists replace the power supply"

PLATFORM_FEP-1-FRU_PS_SIGNAL_FAULTY 1-Alert [chars] signal on FRU power supply [chars] is faulty The specified power supply of RPS has faulty signal hardware LOG_STD_ACTION
PLATFORM_FEP-6-FRU_PS_OIR 6-Information FRU Power Supply [chars] Power Supply inserted or removed firmware LOG_STD_NO_ACTION

PLATFORM_SNMP-3-COMMAND_WARNING

3-Error

The command [[chars]] should not be configured on a stack of switches

A command that is supported for standalone switches only was entered on a stack of switches.

firmware

"Either remove this command from the configuration " "save startup configuration and reload the stack OR " "remove all other stack members from the stack."

NGWC_USB_CONSOLE-3-NO_DNLD

3-Error

Switch [dec]: Firmware download failed

USB Console firmware download failed. There will be no USB console connectivity.

firmware

"Please re-execute the command to download the firmware." LOG_STD_RECUR_ACTION

NGWC_USB_CONSOLE-6-OK_DNLD

6-Information

Switch [dec]: Firmware download successful

This is for information purposes only. The download is successful and no action needs to be taken.

firmware

LOG_STD_NO_ACTION

NGWC_USB_CONSOLE-5-RUNNING_DNLD

5-Notice

Switch [dec]: Firmware download already in progress

Only one download may be running at a time

-

"Wait for the original download to complete " "and print a status message"

NGWC_USB_CONSOLE-6-USB_INSERT

6-Information

Switch [dec]: USB cable inserted. Console media-type USB is in effect

USB console cable inserted

-

LOG_STD_NO_ACTION

NGWC_USB_CONSOLE-6-USB_REMOVE

6-Information

Switch [dec]: USB cable removed. Console media-type RJ45 is in effect

USB console cable inserted

-

LOG_STD_NO_ACTION

NGWC_USB_CONSOLE-6-MEDIA_USB

6-Information

Switch [dec]: Console media-type is USB.

The USB console is currently active.

-

"No action is necessary"

NGWC_USB_CONSOLE-6-MEDIA_RJ45

6-Information

Switch [dec]: Console media-type is RJ45.

The USB console is not active.

-

"No action is necessary"

NGWC_USB_CONSOLE-6-CONFIG_DISABLE

6-Information

Switch [dec]: Console media-type forced to RJ45

Console media type is forced to RJ45 by system configuration.

-

"No action is necessary"

NGWC_USB_CONSOLE-6-CONFIG_ENABLE

6-Information

Switch [dec]: Console media-type changed to default

Media type change requested was invalid

-

LOG_STD_NO_ACTION

NGWC_USB_CONSOLE-6-INACTIVITY_ENABLE

6-Information

Switch [dec]: Console media-type USB configured for inactivity timeout of [dec] minutes

Console media type is forced to RJ45 by system configuration.

-

"No action is necessary"

NGWC_USB_CONSOLE-6-INACTIVITY_DISABLE

6-Information

Switch [dec]: Console media-type USB inactivity timeout disabled

Console media type is forced to RJ45 by system configuration.

-

"No action is necessary"

NGWC_USB_CONSOLE-6-INACTIVITY_REACHED

6-Information

Switch [dec]: Console media-type USB disabled due to inactivity media-type reverted to RJ45.

Console media type is forced to RJ45 by system configuration.

-

"No action is necessary"

PLATFORM_SYS-6-UPTIME

6-Information

Time taken to initialize system = %-4d seconds

This is an informational message for the user. This provides the time taken for the system to initialize on boot. The time is actually the time taken by system to finish initialization after kernel Linux is booted

-

"This is a notification message only. " "No action is required."

PLATFORM_SYS-4-SDM

4-Warning

Unsupported template detected and default template has been loaded

This is a warning message for the user. An unsupported template was configured on the system and the default template has been loaded.

-

"This is a notification message only. " "No action is required."

PLATFORM_SYS-4-IPSEC

4-Warning

Feature Mismatched on stack. IPSEC is configured on the stack but newly inserted switch [dec] does not support IPSEC. Please remove the new switch.

This is a warning message for the user. A feature mismatched in IPSEC. IPSEC is configured on the stack but newly inserted switch does not support IPSEC. Please remove the newly inserted switch.

-

"Remove newly inserted switch."

NGWC_SWITCH_OOR-3-RP_NORMAL_CPU_UTILIZATION

3-Error

Normal CPU utilization under [dec]%% system is normal.

CPU utilization is in normal range.

polaris-platform

LOG_STD_NO_ACTION

NGWC_SWITCH_OOR-3-RP_HIGH_CPU_UTILIZATION

3-Error

High CPU utilization over [dec]%% system performance may be degraded.

Switch performance may be degraded due to high CPU utilization.

polaris-platform

"Try to lower the CPU load"

NGWC_SWITCH_OOR-3-RP_CRITICAL_CPU_UTILIZATION

3-Error

Alarm: Critical CPU utilization over [dec]%% system may fail.

Switch may fail due to extremely high CPU utilization.

polaris-platform

"Try to lower the CPU load"

NGWC_SWITCH_OOR-3-RP_NORMAL_MEM_UTILIZATION

3-Error

Normal memory utilization under [dec]%% system is normal.

Memory utilization is in normal range.

polaris-platform

LOG_STD_NO_ACTION

NGWC_SWITCH_OOR-3-RP_HIGH_MEM_UTILIZATION

3-Error

Warning: Memory utilization over [dec]%% system performance may be degraded.

Switch performance may be degraded due to high memory utilization.

polaris-platform

"Try to lower the memory load"

NGWC_SWITCH_OOR-3-RP_CRITICAL_MEM_UTILIZATION

3-Error

Alarm: Critical memory utilization over [dec]%% system may fail.

Switch may fail due to extremely high memory utilization.

polaris-platform

"Try to lower the memory load"

PLATFORM_STACKPOWER-6-CABLE_EVENT

6-Information

Switch [dec] stack power cable [chars] [chars]

Switch's stack power cable 1/2 is inserted/removed

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-6-LINK_EVENT

6-Information

Switch [dec] stack power protocol is up on cable [chars]

Switch's stack power cable 1/2 is now able to share power

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-TOO_MANY_ERRORS

4-Warning

Switch [dec]: Too many errors seen on port [chars]

Too many errors are seen on switch's stack power port 1/2

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-VERSION_MISMATCH

4-Warning

Major version mismatch in stack power protocol message on switch [dec]

Major version mismatch in stack power protocol message is observed on switch [dec]

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-3-INVALID_TOPOLOGY

3-Error

Invalid power stack topology observed by switch [dec]. [chars]

Power stack topology is invalid. The switch is forced to operate in standalone mode

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-POWER_BUDGET

4-Warning

Switch [dec] power budget is at least 1000W greater than its local supplies

Switch's power budget is more than 1000W above its power supplies rated power output. Please insert a power supply in this system

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-POWER_BUDGET_2K

4-Warning

Switch [dec] power budget is at least 2000W greater than its local supplies

Switch's power budget is more than 2000W above its power supplies rated power output. Please insert a power supply in this system

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-CABLE_A_CURRENT_IN

4-Warning

Switch [dec] stack power cable 1 inward current is over the limit

Switch's stack power cable 1 inward current is over the limit of 40 Amperes. Please add a power supply to the switch

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-CABLE_B_CURRENT_IN

4-Warning

Switch [dec] stack power cable 2 inward current is over the limit

Switch's stack power cable 2 inward current is over the limit of 40 Amperes. Please add a power supply to the switch

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-CABLE_A_CURRENT_OUT

4-Warning

Switch [dec] stack power cable 1 outward current is over the limit

Switch's stack power cable 1 outward current is over the limit of 40 Amperes. Please move a power supply out of the switch

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-CABLE_B_CURRENT_OUT

4-Warning

Switch [dec] stack power cable 2 outward current is over the limit

Switch's stack power cable 2 outward current is over the limit of 40 Amperes. Please move a power supply out of the switch

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-UNDER_BUDGET

4-Warning

Switch [dec] does not have sufficient power budget

Switch's power budget is less than minimum required switch budget

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-UNBALANCED_PS

4-Warning

Switch [dec]'s power stack has unbalanced power supplies

Switch's power stack has a switch with multiple power supplies while another switch in the same power stack has no power supplies

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-INSUFFICIENT_PWR

4-Warning

Switch [dec]'s power stack does not have enough power

Switch's power stack does not have enough power to bring up all the switches in that power stack

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-PRIO_CONFLICT

4-Warning

Switch [dec]'s power stack has conflicting power priorities

Switch's power priorities are conflicting with power priorities of another switch in the power stack

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-UNDER_VOLTAGE

4-Warning

Switch [dec] experienced an under voltage condition

Switch had an under voltage condition on last boot up /shutdown

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-GLS_EVENT

4-Warning

Switch [dec] experienced a graceful load shed event

Switch had to shed loads based on a SOC condition

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-ILS_EVENT

4-Warning

Switch [dec] experienced an immediate load shed event

Switch had to shed loads based on a PS_FAIL condition

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-SRLS_EVENT

4-Warning

Switch [dec] experienced a system ring load shed event

Switch had to shed loads based on loss of a system

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-SSLS_EVENT

4-Warning

Switch [dec] experienced a system star load shed event

Switch had to shed loads based on loss of a system

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-UVLS_EVENT

4-Warning

Switch [dec] experienced an under voltage load shed event

Switch had to shed loads based on an under voltage condition

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-REDUNDANCY_LOSS

4-Warning

Switch [dec]'s power stack lost redundancy and is now operating in power sharing mode

Power stack that this switch is part of has lost redundancy and is now operating in power sharing mode

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-BISP

4-Warning

Switch [dec] experienced a BISP event

Switch experienced a Built-in Self Protection event

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-NEIGHBOR_BISP

4-Warning

Switch [dec]'s neighbor switch experienced a BISP event

A neighbor switch experienced a Built-in Self Protection event

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-NEIGHBOR_GLS

4-Warning

Switch [dec]'s neighbor switch experienced a graceful load shed event

A neighbor switch had to shed loads based on a SOC condition

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-NEIGHBOR_ILS

4-Warning

Switch [dec]'s neighbor switch experienced an immediate load shed event

A neighbor switch had to shed loads based on a PS_FAIL condition

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-NEIGHBOR_SRLS

4-Warning

Switch [dec]'s neighbor switch experienced a system ring load shed event

A neighbor switch had to shed loads based on loss of a system

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-NEIGHBOR_SSLS

4-Warning

Switch [dec]'s neighbor switch experienced a system star load shed event

A neighbor switch had to shed loads based on loss of a system

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-NEIGHBOR_UVLS

4-Warning

Switch [dec]'s neighbor switch experienced an under voltage load shed event

A neighbor switch had to shed loads based on an under voltage condition

firmware

LOG_STD_ACTION

PLATFORM_STACKPOWER-4-BISP_POE_OVER_I

4-Warning

Switch [dec] experienced a PoE over-current BISP event

Switch experienced a PoE over-current Built-in Self-Protection event

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-BISP_POE_PORT

4-Warning

Switch [dec] experienced a port BISP event

Switch experienced a port Built-in Self-Protection event which affected PoE

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-BISP_PORT_A_SC

4-Warning

Switch [dec] experienced a short-circuit BISP event on port 1

Switch experienced a short-circuit Built-in Self-Protection event on port 1

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-BISP_PORT_B_SC

4-Warning

Switch [dec] experienced a short-circuit BISP event on port 2

Switch experienced a short-circuit Built-in Self-Protection event on port 2

firmware

"This is a notification message only." " No action is required."

PLATFORM_STACKPOWER-4-BISP_NBR_DEAD

4-Warning

Switch [dec]'s neighbor experienced a major BISP event

Switch's neighbor experienced a major Built-in Self-Protection event which caused the switch to shutdown

firmware

"This is a notification message only." " No action is required."

NGWC_FMANRP_IPSEC-4-UNSUPPORT_MIXSTACKING

4-Warning

Mixed stacking is detected. [chars] for IPSEC

IPSEC feature is not supported on mixed stacking system

accsw-p-security

"show platform"

NGWC_FMANRP_IPSEC-3-UNSUPPORT_DATAPATH

3-Error

IPSEC datapath is not supported as mixed stacking was detected. Reload is required when stacking is changed to unmixed

This operation is not supported on mixed stacking

accsw-p-security

"show platform"

NGWC_FMANRP_IPSEC-3-UNSUPPORT_CONFIGURATION

3-Error

This configuration is not supported on [chars]

This operation is not supported on the system

accsw-p-security

"show platform"

PANGEA_QOS-3-MIXFILTER

3-Error

[chars] [chars]

The Leaba platfrom does not support MPLS or L2 COS filter with other fitlers

pangea-qos

"show policy-map"

PANGEA_QOS-3-DIFFTBLMAP

3-Error

From and To type should be same except if to type is traffic-class discard-class or qos-group for tablemap

From and To type should be same except if to type is traffic-class discard-class or qos-group for tablemap

pangea-qos

"show policy-map"

FMANRP_NAT-4-NOSWIDB

4-Warning

Sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a swidb structure.

iosxe-nat

"show ip interface"

FMANRP_NAT-3-IFTDLMSGMARSHAL

3-Error

Failed to copy interface config essage to IPC buffer for \n\ Interface [chars] 0x[hec] domain [chars] operation [chars]

This operation to build a TDL message for interface configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NONATSERVICE

4-Warning

Service structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT service structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-3-SERTDLMSGMARSHAL

3-Error

Failed to copy service config message to IPC buffer for\n\ application type [dec] protocol type [dec] port [dec]

This operation to build a TDL message for service configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-SERVICERM

3-Error

Failed to delete NAT services for appl type [chars] protocol [chars]\n\ port [dec]

An unexpected condition has occurred which is due to the failure\n\ to remove data structures for NAT special services.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NOPOOL

4-Warning

Pool structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT pool structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-4-NOMAPPING

4-Warning

A mapping structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT mapping structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-4-BADACTION

4-Warning

Invalid action [dec] for NAT configuration

An unexpected condition has occurred which is invalid action \n\ for a NAT configuration.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-3-POOLTDLMSGMARSHAL

3-Error

Failed to copy pool config message to IPC buffer for\n\ pool [chars] id [dec]

This operation to build a TDL message for pool configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-MAPPINGTDLMSGMARSHAL

3-Error

Failed to copy mapping config message to IPC buffer for\n\ mapping id [dec] vrf table id [dec]

This operation to build a TDL message for mapping configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IFADDRTDLMSGMARSHAL

3-Error

Failed to copy interface address change message to IPC buffer for\n\ interface [chars] new address [inet]

This operation to build a TDL message for NAT interface address\n\ configuration has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-VRFDELTDLMSGMARSHAL

3-Error

Failed to copy VRF delete message to IPC buffer for vrf table id [dec]

This operation to build a TDL message for vrf deletion configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-TIMEOUTTDLMSGMARSHAL

3-Error

Failed to copy timeout config message to IPC buffer for\n\ timeout type [dec]

This operation to build a TDL message for timeout configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NORANGE

4-Warning

Pool address range structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT pool address range structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-3-RANGETDLMSGMARSHAL

3-Error

Failed to copy pool address range config message to IPC buffer for\n\ pool [chars] range start [inet] range end [inet]

This operation to build a TDL message for address range configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTTDLMSGMARSHAL

3-Error

Failed to copy portlist config message to IPC buffer for\n\ addr [inet] proto [dec] start_port [dec] end_port [dec]

This operation to build a TDL message for portlist add/delete\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NOACL

4-Warning

Access list is null

An unexpected condition has occurred which is due to the absence of\n\ an access list structure.

iosxe-nat

"show ip access-lists"

FMANRP_NAT-3-MAXENTRYTDLMSGMARSHAL

3-Error

Failed to copy max entry config message to IPC buffer for\n\ type [chars] entry data 0x[hec] max_limit [dec]

This operation to build a TDL message for max entry add/delete\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-STATSUPDTDL

3-Error

Failed to update NAT [chars] statistics

An unexpected condition has occurred when updating statistics

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPALIASTDL

3-Error

Error with ipalias message received from data path

An unexpected condition has occurred with received ipalias \n\ message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPALIASTYPE

3-Error

Received ipalias message from data path with unsupported \n\ address type [dec]

An unexpected condition has occurred with received ipalias \n\ message from data path with unsupported address type

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPSTATICROUTETDL

3-Error

Error with static ip route message received from data path

An unexpected condition has occurred with received static\n\ ip route message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPSTATICROUTETYPE

3-Error

Received ip static route message from data path with\n\ unsupported address type

An unexpected condition has occurred with received static \n\ ip route message from data path with unsupported address type

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTTDL

3-Error

Error with portlist allocation request message received from data path

An unexpected condition has occurred with received portlist\n\ allocation request message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTTYPE

3-Error

Address type [dec] for global address in the portlist allocation request is not supported

An unexpected address type has occurred with received portlist\n\ allocation request message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTPROTO

3-Error

Protocol type [dec] for global addr [inet] in the portlist allocation request is not supported

An unexpected protocol type has occurred with received portlist\n\ allocation request message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-DEBUGTDLMSGMARSHAL

3-Error

Failed to copy debug NAT request message to IPC buffer

This operation to build a TDL message for debug NAT command \n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IOSDENQUEUE

3-Error

Failed to enqueue NAT [chars] message for transmission

This operation to enqueue an IPC message for sending has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-AVLTREEWALK

3-Error

Failed to walk NAT [chars] database for [chars]

This operation to perform stale processing has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-AVLDELETE

3-Error

Failed to delete node from NAT [chars] database for [inet]

This operation to perform delete processing has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-WLANSESSTDL

3-Error

Error with WLAN session message received from data path

An unexpected condition has occurred with received WLAN session \n\ message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-WLANSESSTYPE

3-Error

Received WLAN session message from data path with unsupported \n\ address type [dec]

An unexpected condition has occurred with received WLAN session \n\ message from data path with unsupported address type

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-WLANSESSIDB

3-Error

Received WLAN session message from data path with nil \n\ input interface for inside local host [inet]

An unexpected condition has occurred with received WLAN session \n\ message from data path with nil input interface

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NOLOGGINGPARAM

4-Warning

Highspeed logging structure is nil

An unexpected condition has occurred which is due to the absence of\n\ a logging parameter structure.

iosxe-nat

"show running"

FMANRP_NAT-4-LOGGING_PARAM

4-Warning

Highspeed logging export [chars] [dec] unsupported

An unsupported exporting paremeter for highspeed logging\n\ on data path is received.

iosxe-nat

"show running"

FMANRP_NAT-4-NOREPLICATEPARAM

4-Warning

Session replication structure is nil

An unexpected condition has occurred which is due to the absence of\n\ a session replication parameter structure.

iosxe-nat

"show running"

FMANRP_NAT-3-MIBEVENT

3-Error

Failed to get NAT MIB response message: [chars]

An unsupported error occured with waiting for NAT MIB respsonse \n\ message.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-INVALID_ADDRESS

3-Error

Received an invalid address [inet]

An unsupported address for the given config was received.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-MSGALLOCERR

3-Error

Failed to allocate message

When attempting to send message to dataplane there was not enough memory to allocate the message.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-NATSETTDLMSGFAIL

3-Error

When download [chars] failed to set a field in message

sotware error.

iosxe-nat

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGDISPATCHNULL

4-Warning

TDL messages NULL from IOS.

An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGDISPATCH

4-Warning

Unable to dispatch received TDL message '[chars]' from Forwarding Manager. LUID: [chars]

An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGIPCERR

4-Warning

Unable to process received IPC messages from Forwarding Manager\n\ error: [chars].

An unexpected condition has occurred while IOS trying to process\n\ received IPC message from Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-3-EPOCHTDLMSGMARSHAL

3-Error

Failed to copy epoch TDL message to IPC buffer epoch number [dec]

This operation to build a TDL messages for epoch message has failed.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-3-MSGMARSHALERR

3-Error

Unable to copy IPC messages into transport buffer. Message: [chars]

An unexpected condition has occurred while IOS trying to copy \n\ IPC message to transport buffer in order to send the message\n\ from IOSd to Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-3-MSGENQERR

3-Error

Unable to enqueue IPC messages to IOS IPC queue. Message: [chars].

An unexpected condition has occurred while IOS trying to enqueue \n\ IPC message to IOS IPC queue in order to send the message to\n\ Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGNONTDLSTATSERR

4-Warning

Unable to process received non-TDL stats message from \ Forwarding Manager\n\ error: [chars] [dec].

-

-

-

PLATFORM_THERMAL-6-FRU_FAN_OIR

6-Information

Switch [dec]: System fan [dec] [chars]

System fan inserted or removed

firmware

LOG_STD_NO_ACTION

PLATFORM_THERMAL-6-FRU_FAN_RECOVERY

6-Information

Switch [dec]: System fan [dec] recovered to normal status

Fan recovered

firmware

LOG_STD_NO_ACTION

PLATFORM_THERMAL-1-FRU_FAN_FAILURE

1-Alert

Switch [dec]: System fan [dec] failed

Fan failed

firmware

"Replace the fan."

PLATFORM_THERMAL-1-FRU_FAN_NOT_PRESENT

1-Alert

Switch [dec]: System fan [dec] not present

Fan not present

firmware

"Insert fan."

PLATFORM_THERMAL-1-FRU_FAN_INSERT_OR_RECOVERY

1-Alert

Switch [dec]: System fan [dec] inserted or recovered

Fan in funtional mode

firmware

LOG_STD_NO_ACTION

PLATFORM_THERMAL-1-FRU_FAN_FAULTY_OR_REMOVED

1-Alert

Switch [dec]: System fan [dec] faulty or removed

Fan in non-funtional mode

firmware

"Need an action"

PLATFORM_THERMAL-1-FAN_CRITICAL

1-Alert

Switch [dec]: [chars]

Faulty fansFRU fan or PS fan detected

hardware

"Replace the faulty fans and then turn on the system"

PLATFORM_THERMAL-1-TEMP_NOT_FUNCTIONAL

1-Alert

Switch [dec]: Temperature measurement not functioning. Condition may be transient.

Temperature not detectedi by IOS

firmware

"Check that fans are working. Check 'show env temperature' command output. If condition persists contact TAC."

PLATFORM_THERMAL-4-SECONDARY_OVERTEMP

4-Warning

Switch [dec]: [chars]

The chassis inside temperature exceeds the configured threshold\n\ but less or equal to the max inside temperature

-

-

PLATFORM_THERMAL-3-OVERTEMP

3-Error

Switch [dec]: [chars]

The chassis inside temperature exceeds the max temperature threshold

-

-

PLATFORM_THERMAL-2-OVERTEMP_SHUTDOWN

2-Critical

Switch [dec]: [chars]

The chassis inside temperature exceeds the max temperature threshold and will be shut down immediately.

-

-

PLATFORM_THERMAL-3-UNDERTEMP

3-Error

Switch [dec]: [chars]

The chassis inside temperature is below the min temperature threshold

-

-

PLATFORM_THERMAL-2-UNDERTEMP_SHUTDOWN

2-Critical

Switch [dec]: [chars]

The chassis inside temperature is below the min temperature threshold and will be shut down immediately.

-

-

PLATFORM_THERMAL-6-TEMP_NORMAL

6-Information

Switch [dec]: temperature is within the normal limit.

The temperature sensor value is within the normal limit

hardware

LOG_STD_NO_ACTION

PLATFORM_THERMAL-2-VIOL_SEC_UNAVAILABLE

2-Critical

Switch [dec]: [chars]

The chasfs property for violation second is not present.

-

-

PLATFORM_THERMAL-1-FRU_FAN_DISABLED

1-Alert

Switch [dec]: System fan [dec] disabled. Airflow direction for this fan should be [chars]

FRU fan disabled because majority of fans have different airflow than this fan

hardware

"Fan disabled because of airflow direction. Replace the fan that has airflow consitent with other fans in the system"

PLATFORM_THERMAL-1-FRU_FAN_INSUFFICIENTFANTRAYSDETECTEDPOWERDOWN

1-Alert

Switch [dec]: Too few working fan trays exist and the switch will overheat. If this situation is not resolved by installing [dec] fan trays in a [chars] airflow direction the switch will power down in [dec] minutes

Insufficient fan trays in the system

hardware

"Insert fan."

SBC_MPS-3-INTERNAL

3-Error

An internal IOSd SBC error has been encountered[chars].

An internal error has been encountered.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-3-INITFAIL

3-Error

SBC module initialisation failure: [chars].

An unexpected condition has occurred which resulted in the module being unable to initialise.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-3-MAX_RESOURCES

3-Error

The maximum resource limit has been reached.

The system was asked to allocate more resources but the maximum\n\ resource limit had already been reached

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-3-ENQUEFAIL

3-Error

Enqueue of TDL message failed [chars].

-

-

-

SBC_MPS-6-UNEXPECTED_TDL

6-Information

An unexpected message [chars] has been received by SBC while in the

An internal message has been received by SBC but it was not expecting\n\ that message at that particular time. The system will ignore the\n\ message and continue operation.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-4-UNEXPECTED_PKT

4-Warning

An unexpected packet for call [dec] has been received by SBC.

A packet been received by SBC for the noted call but the call was not\n\ in a correct state to handle it. The system will ignore the packet and\n\ continue operating.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-3-UNEXPECTED_TIMOUT

3-Error

An unexpected timeout has been encountered by SBC [chars].

A timeout was experienced by the IOSd SBC subsystem but no such\n\ timeout should have occurred. The system will ignore the timeout and\n\ continue operating.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-6-DEACTIVATE_NO_RSP

6-Information

SBC deactivate response is considered lost.

The response for SBC deactivate can get lost due to FP startup or switchover while deactivation is in progress.

asr1k-sbc

"SBC can be activated now if needed."

SBC_MPS-6-DEACTIVATE_RESPONSE

6-Information

SBC deactivate is complete.

SBC deactivation can take a while. This happens when SBC deactivation is done in the presence of a lot calls with deactivation-mode set to abort. SBC deactivate is now complete.

asr1k-sbc

"SBC can be safely activated now if needed."

SBC_MPS-4-NEW_MPF_CAPABILITIES

4-Warning

New SBC MPF Capabilities handling failure.

SBC has received a new set of Media Packet Forwarding capabilities from the associated Forwarding Processor that are inconsistent with those already in use. SBC was unable to process these new capabilities online and will automatically restart.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-4-TRANSCODE_MPF_CAPABILITIES

4-Warning

Transcoding SBC MPF Capabilities handling failure.

SBC has been unable to prepare a transcoding supported Media Packet Forwarding capabilities message. SBC will not be able to support transcoding functionality.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-4-MPF_SRTP_CAPABILITIES

4-Warning

Unable to set SRTP capabilities

SBC made an attempt to set the platform capabilities with respect to its handling of SRTP streams and was not successful. SRTP streams will not be handled through the SBC.

asr1k-sbc

LOG_STD_ACTION

SBC_MPS-4-MPF_CAPABILITIES

4-Warning

SBC MPF Capabilities handling failure.

SBC has been unable to properly prepare a Media Packet Forwarding capabilities message. SBC may not be able to support select functionality such as transcoding or SRTP.

asr1k-sbc

LOG_STD_ACTION

CRIMSON-3-INITFAIL

3-Error

Initialization of the IOS operational database facility failed [chars].

-

-

-

CRIMSON-3-INITFAIL_OPER_FLUSH

3-Error

Initialization of the IOS operational database flush facility failed.

An unexpected condition has occurred which resulted in the IOS operational database flush facililty failing to start. External agents will not be able to access the contents of the IOS operational database.

crimson

LOG_STD_ACTION

CRIMSON-3-INITFAIL_OPER_REDO

3-Error

Initialization of the IOS operational database redo facility failed.

An unexpected condition has occurred which resulted in the IOS operational database redo facililty failing to start. This is a serious problem and means that the IOS operation database facility will not be functional.

crimson

LOG_STD_ACTION

CRIMSON-3-UPDATE_FAIL

3-Error

Processing of a IOS operational database update failed [chars].

-

-

-

CRIMSON-3-IOS_CONFIG_DB_VALIDATION_FAIL

3-Error

Data validation of the IOS configuration database failed [chars].

-

-

-

CRIMSON-3-IOS_CONFIG_DB_GARBAGE_COLLECTION_START_FAIL

3-Error

Unable to start the garbage collection process for the IOS config database

The IOS configuration database garbage collection has failed to start. Without a garbage collection process stale objects will not be cleaned up.

crimson

LOG_STD_ACTION

CRIMSON-3-NESTED_LOCK

3-Error

Database already locked by [chars].

An unexpected condition has occurred wherein the already locked IOS operational database was requested to be locked again. This problem means that external entities may not receive updates when operational data changes.

crimson

LOG_STD_ACTION

CRIMSON-3-DATABASE_MEMLEAK

3-Error

Database memory leak detected in [chars] database [chars]/[chars]/[chars] size: %llu byte

A memory leak has been detected in the database memory. The leaked object is identified by name

crimson

LOG_STD_ACTION

CRYPTO_SL_TP_LEVELS-3-VAR_SET_FAILED

3-Error

Update of rommon variable failed: retcode=[dec]

Call to update rommon variable failed

-

LOG_STD_ACTION

CRYPTO_SL_TP_LEVELS-6-VAR_NEW_VALUE

6-Information

Setting crypto bidir throughput to: [dec] kbps

Crypto throughput rommon var updated

-

"No action required. Informational message."

CRYPTO_SL_TP_LEVELS-6-TP_THROTTLE_STATE

6-Information

Crypto throughput [chars] throttled. New level is [dec]

Maximum throughput level is the same as unthrottled. All other levels are throttled

-

"No action required. Informational message."

CRYPTO_SL_TP_LEVELS-3-INV_PLATFORM_VALUE

3-Error

Invalid platform level value token: [chars]

-

-

LOG_STD_ACTION

CRYPTO_SL_TP_LEVELS-3-INV_DEFAULT_VALUE

3-Error

Invalid platform default value token: [chars]

-

-

LOG_STD_ACTION

CRYPTO_SL_TP_LEVELS-6-INV_ROMMON_VALUE

6-Information

Invalid throughput option [dec] kbps foundupdating rommon to [dec] kbps

Invalid throughput option in rommon for crypto throughputResetting the throughput option to the default value

-

"No action required. Informational message."

CRYPTO_SL_TP_LEVELS-3-NO_VALID_PLATFORM_VALUES

3-Error

No valid platform level values specified

-

-

LOG_STD_ACTION

CRYPTO_SL_TP_LEVELS-3-ROMMON_WRITE_FAILED

3-Error

Error in updating rommon variable

-

-

LOG_STD_ACTION

CRYPTO_SL_TP_LEVELS-6-ROMMON_VAL

6-Information

Current rommon value: [dec]

-

-

-

CRYPTO_SL_TP_LEVELS-6-TP_LEVEL_LIMITED

6-Information

HSECK9 is disabled: bandwidth restricted to 250Mbps

-

-

-

CRYPTO_SL_TP_LEVELS-6-TP_LICENSE_TP_REQUEST_FAILED

6-Information

License request failed rc=[dec] sle_ret_val=[dec]

License request failed. Data plane will use platform default throughput level

-

"Look at other logs/debugs to see reason for failure."

CRYPTO_SL_TP_LEVELS-6-TP_LICENSE_HSEC_REGISTER_FAILED

6-Information

License registration failed rc=[dec]

License request failed.

-

"Look at other logs/debugs to see reason for failure."

CRYPTO_SL_TP_LEVELS-6-TP_LICENSE_HSEC_REQUEST_FAILED

6-Information

License request failed rc=[dec]

HSECK9 License request failed.

-

"Look at other logs/debugs to see reason for failure."

VIRT_SERVICE-3-INIT_FAIL

3-Error

Failed to initialize required virtual service object: [chars]

During the initialization of the resources required for the virtual service feature a memory allocation failure occurred. This has prevented the virtual service feature from being enabled.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-ROMMON_UNSUPPORTED

3-Error

ROM monitor configuration does not support virtualization

Virtualization is not supported by the current ROM monitor configuration. Verify both the ROM monitor version and ROM monitor variable ENABLE_VTX are correct to enable virtualization.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-STBY_ROMMON_UNSUPPORTED

3-Error

Standby ROM monitor configuration does not support virtualization

Virtualization is not supported by the current ROM monitor configuration on the standby. Verify both the ROM monitor version and ROM monitor variable ENABLE_VTX are correct to enable virtualization.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-ACTIVATE_FAIL

3-Error

Failed to send virtual service [chars] activate message

During the creation and transmission of the virtual service activate TDL message a failure occurred. The message was not successfully sent and therefore the virtual service was not activated.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-DEACTIVATE_FAIL

3-Error

Failed to send virtual service [chars] deactivate message

During the creation and transmission of the virtual service deactivate TDL message a failure occurred. The message was not successfully sent and therefore the virtual service was not deactivated.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-UNPROVISION_FAIL

3-Error

[chars]: [chars]

During the unprovision of the named virtual service an unexpected failure occurred.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-STBY_PKG_PATH

3-Error

Failed to [chars] required by virtual service [chars] on standby

Specified package definition file was not found on standby. Configuration was accepted. Copy package definition file to standby at earliest convenience.

vman

LOG_STD_ACTION

VIRT_SERVICE-4-SWITCHOVER_ACTIVATE

4-Warning

Virtual service [chars] will not be activated following a switchover

Following a switchover this virtual service will not be activated as there is an issue with its package definition file. Copy package definition file to standby at earliest convenience.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-PKG_PATH

3-Error

Failed to [chars] required by virtual service [chars]

Specified package definition file was not found following a switchover.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-PKG_PATH_ACTIVATE

3-Error

Failed to [chars]. Virtual service [chars] will not be activated

Specified package definition file was not found following a switchover. Unable to activate virtual service without specified package definition file present.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-INVALID_APPLIANCE_TIMEOUT

3-Error

A response timeout occurred for an invalid virtual service

An unexpected condition occurred where the virtual service context pointer in the expired timer was set to NULL.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-UNKNOWN_APPLIANCE_TIMEOUT

3-Error

A response timeout occurred for unknown virtual service [chars]

A response timeout occurred for a virtual service that is no longer in the virtual service database.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-RESPONSE_TIMEOUT

3-Error

Virtual service [chars] timed out waiting for a response from Virt-manager

Failed to receive a response message from Virt-manager for last activation operation performed on the named virtual service. The virtual service activation state was marked as deactivated.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-UPGRADE_TIMEOUT

3-Error

Virtual service [chars] timed out waiting for a package upgrade response from Virt-manager

Failed to receive a response message from Virt-manager for last upgrade operation performed on the named virtual service.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-SEND_RF_MSG

3-Error

Failed to send RF message to peer - [chars]

An unexpected condition occurred where an attempt to send an RF message to peer failed.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-INVALID_RF_MSG

3-Error

Received an invalid RF message type from peer

An unexpected condition occurred where an invalid message type was detected.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-UNKNOWN_RF_MSG

3-Error

Received an unknown RF message type [dec] from peer

An unexpected condition occurred where an unknown timer event was detected.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-UNKNOWN_TIMEOUT_TYPE

3-Error

A response timeout occurred for an unknown timeout type [dec]

An unexpected condition occurred where an unknown timeout type was detected.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-UNKNOWN_TIMER_EVENT

3-Error

A timer event occurred for an unknown timer event [dec]

An unexpected condition occurred where an unknown timer event was detected.

vman

LOG_STD_ACTION

VIRT_SERVICE-5-ACTIVATION_STATE

5-Notice

[chars] [chars]

The activation state of the named virtual service has changed as notified by Virt-manager.

vman

LOG_STD_ACTION

VIRT_SERVICE-3-RESET

3-Error

Virtual service [chars] reset

An unexpected condition has occurred where Virt-manager has reported that it detected the named virtual service reset. This virtual service is not configured to be activated and as such no attempt to reactivate it will be made.

vman

LOG_STD_ACTION

VIRT_SERVICE-5-RESET_REACTIVATE

5-Notice

Virtual service [chars] reset and will be reactivated

Virt-manager has reported that it detected the named virtual service reset. An attempt will be name to reactivate this virtual service.

vman

LOG_STD_ACTION

VIRT_SERVICE-5-INSTALL_STATE

5-Notice

[chars] [chars]

The installation state of the named virtual service has changed as notified by Virt-manager.

vman

LOG_STD_ACTION

IOSXE_EZMENU-3-VIRT_SRVC_REGISTER

3-Error

Failed to register '[chars]' with virtual service manager

An unexpected error has occured while trying to register this virtual service with the virtual service manager. This has prevented the virtual service from being enabled/disabled.

vman

LOG_STD_ACTION

ACE-3-INITFAIL

3-Error

[chars]: initialization failed [chars]

An error occured in the indicated control transaction.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-6-SWITCHOVER

6-Information

VPN-SM switchover: [dec]/[dec] has been [chars] [dec]/[dec]

An negative acknowledge occured in the indicated control transaction.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-NOMORETID

3-Error

[chars]: out of [chars] transactions

Transaction pool for the indicated transaction type was\n\ exhausted.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-INVTID

3-Error

[chars]: [chars] of invalid [chars] trans id [dec]

An invalid transaction ID of for the indicated transaction\n\ type was encountered

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-HAPITRUNC

3-Error

[chars]: Received truncated HAPI message tlen=[dec] actual=[dec]

An IPsec packet was unexpectedly forwarded to the RP

iosxe-ipsec

"If this message was seen in the context of the router booting " "enabling the hardware crypto accelerator then this message is normal " "and can be safely ignored. " "Otherwise please copy the error message exactly as it appears " "and report it to your technical support representative."

ACE-3-CRASHDUMPSTART

3-Error

[chars]: crashdump retrieval initiated to file [chars]

The ACE crashed and was rebooted. Upon reboot a crashdump file was detected and uploaded to the sup-bootflash filesystem.

-

"Report the crash and transfer the crashdump file to your technical" "support representative."

ACE-6-CRASHDUMPEND

6-Information

[chars]: crashdump retrieval complete

The ACE crashed and was rebooted. Upon reboot a crashdump file was detected and uploaded to the sup-bootflash filesystem.

-

"Report the crash and transfer the crashdump file to your technical" "support representative."

ACE-3-CRASHDUMPERR

3-Error

[chars]: crashdump retrieval error: [chars] [chars]

An error occurred during crashdump file retrieval from ACE.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-6-BOOTMSGINFO

6-Information

[chars]: boot info: [chars]

The ACE completed booting but with a non-zero informational status code. This does not indicate an error and ACE will run normally.

-

"No action is necessary."

ACE-3-BOOTMSGERR

3-Error

[chars]: boot error: [chars]

The ACE completed booting but with an error status code. ACE will not operate and it will not register with the crypto subsystem.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-OUTOFRES

3-Error

Too many [chars] in the system. Cannot allocate a new one

All VPN-accelerator resources of a particular are in used and thus this allocation request fails.

iosxe-ipsec

"Remove the cryptomap set from the interface. " "Reduce the number of that resource in the " "system. For ACL reduce the number of ACL " "permit ACE in the system. For cryptomap reduce the" "number of cryptomaps in the system. For SPD and " "SPD map reduce the number of interface with " "cryptomap set attached."

ACE-2-INTTABOPERR

2-Critical

Internal [chars] table error: [chars]

Internal table operation fails. This means the state of the module is mostly like inconsistent.

iosxe-ipsec

"Contact your technical support representative"

ACE-2-CRYPTOENGERR

2-Critical

Crypto engine error: [chars] [dec]

A crypto engine operation did not complete. This error condition can indicate that the crypto engine cannot bind or unbind an interface to a crypto engine. It can also indicate that the crypto engine cannot query an interface ID.

-

"Remove the cryptomap set from the interface by issuing " "<CmdBold>no crypto map<noCmdBold> command. Then reattach the cryptomap " "set to the interface using <CmdBold>crypto map<noCmdBold> command. " "Although removing and reattaching the crypto map might fix the " "cryptographic engine operation failure report the failure to your " "technical support representative along with the sequence of commands " "that lead to the failure".

ACE-6-INFO

6-Information

[chars]: [chars]

This is informational message from ACE

iosxe-ipsec

"This is informational message from ACE. This occurs " "in normal operation."

ACE-3-OUTOFID_RL

3-Error

Too many [chars] IDs in the system. Cannot allocate a new one

All the IDs of the specified type are in use

iosxe-ipsec

"Reduce the traffic load number of IPSec tunnels and/or frequency of re-key." "If this message was seen under light loading conditions then" "copy the error message exactly as it appears and report it to your " "technical support representative."

ACE-3-NOENGINESLOT

3-Error

Interface [chars] has no crypto engine slot

An IKE SA was requested for a given interface but no crypto engine slot was assigned to that interface

iosxe-ipsec

"Configure the interface in question with the" " `crypto engine [sub]slot' command"

ACE-3-CEAL_REGISTRATION

3-Error

ACE [chars] failed to register.

The ACE failed to register with CEAL

iosxe-ipsec

"Reset the hw module"

ACE-4-BV_IDMGR_DESTROY

4-Warning

ACE failed to destroy [chars] ID manager. Leaking memory.

The ACE failed to destroy memory space for ID management.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

IOSXE_VMAN-3-MSGINITFAIL

3-Error

Failed to initialize required Virt-manager resource: [chars]

During the initialization of the resources required by Virt-manager a failure occurred. This has prevented virtual services from being activated.

vman

LOG_STD_ACTION

IOSXE_VMAN-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message from Virt-manager

An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from Virt-manager.

vman

LOG_STD_ACTION

IOSXE_VMAN-3-RSPMSGHDLR

3-Error

Failed to deliver response message: [chars]

An unexpected condition has occurred while IOS was trying to deliver a response message to a virtual service received from Virt-manager.

vman

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGNOCAND

3-Error

Can not construct a candidate entry for configuration export

This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGNOPWARR

3-Error

Can not construct an array for configuration export

This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGNOUPDATEMSG

3-Error

Can not construct an update message for configuration export

This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGNOREPLMSG

3-Error

Can not construct a replace message for configuration export

This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-2-MSGNOEXP

2-Critical

Can not construct a '[chars]' message for configuration export: [chars]

This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-2-MSGTDLINITERROR

2-Critical

Configuration Notification messaging module initialization failed: Unable to initialize messaging: [chars]

The Configuration Notification subsystem has failed to initialize the infrastructure for messaging with the Pluggable Services Daemon. Notification of configuration to critical modules cannot proceed.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-2-MSGTDLERROR

2-Critical

Error processing TDL message. [dec]

An unexpected condition in which IOS has received a TDL \n\ message which it can not process.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-2-MSGIPCINITERROR

2-Critical

Error initializing IPC queue

An unexpected condition in which IOS could not initialize\n\ a message queue to the PSD.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGIPCTXERROR

3-Error

IPC transmit error. [dec]

An unexpected condition in which IOS encountered an error\n\ trying to send a message to another process. [dec]

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGOBJNULL

3-Error

An unexpected condition in which IOS has received a null\n\ pointer that it expects to be non-null.

An unexpected condition has occurred while IOS is trying to process\n\ a username command.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MSGENCRYPTINVALID

3-Error

The mcprp_cfg_notify subsystem has seen an encryption type it does\n\ not recognize. [dec]

An unexpected condition has occurred while IOS is trying to process\n\ a username command.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-NVWRITE_EXPORT

3-Error

Failed to export [chars] notification: [dec]

When a 'write memory' or 'write erase' operation occurs the Configuration Notification subsystem exports this event into the chassis file system. This message indicates that the export failed.

access

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MCP_DBPERSIST_STAT

3-Error

Failed to read [chars] property: [dec]

When a 'reload' operation occurs this chasfs property is read to determine the status of the DB persist/restore/delete operation. This message indicates that the read failed.

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MCP_DBPERSIST_ERROR

3-Error

System configuration update could not complete

When a 'reload' operation occurs this chasfs property is read to determine the status of the DB persist/restore/delete operation. This message indicates that the operation failed.

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MCP_FRU_LOCATION

3-Error

Failed to get local FRU location: [dec]

Unable to get local FRU location

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MCP_FRU_INVALID

3-Error

Unknow FRU location: [chars]

Unknown FRU location

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-BOOT_VAR_NOT_SET

3-Error

Either the boot variable does not exist or the buffer is too small. Keep it blank.

Boot variable either does not exist or buffer is too small. Not able to set boot variable. Ignoring it.Aborting reload.

asr1k-chassismgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-BOOT_IMAGE_NOT_FOUND

3-Error

Primary image is not found the system is going to reload as per user request.

Primary image which is set in boot statement either does not exist or not found. Primary image is not found it should prompt the user to see if they wish to proceed. Aborting reload.

asr1k-chassismgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-BOOT_IMAGE_NOT_COMPATIBLE

3-Error

Primary image is not compatible the system is going to reload as per user request.

Primary image which is set in boot statement is not compatible with system. Primary image incompatible it should prompt the user to see if they wish to proceed. Aborting reload.

esg-chassismgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-BOOT_IMAGE_VALIDATE_UNSUPPORTED_PLATFORM

3-Error

Boot image validate function does not recognize the current platform type. This is likely due to new chassis/platform variant being introduced. The reload operation is not affected however presence of this syslog indicates that esg-chassismgr component owner should investigate and determine root cause.

Boot image validate function does not recognize the current platform type. This is likely due to new chassis/platform variant being introduced. The reload operation is not affected however presence of this syslog indicates that esg-chassismgr component owner should investigate and determine root cause.

esg-chassismgr

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-6-IOX_SERVICE_NOTSUPPORTED

6-Information

IOx service not supported.

IOx service is not supported in this platform currently. This may be either due to the feature unavailability or due the current inadequate license level of the system.

iox-caf

-

IOSXE_RP_CFG_NOT-6-MCPRP_BINARY_CFG_MISSING

6-Information

Binary configuration missing.

System is booted with ASCII based startup configuration. Please perform \write mem\ to generate binary configuration. System uses binary-config internally to reduce overall bootime significantly.

polaris-mgbl-infra

-

IOSXE_RP_CFG_NOT-3-MCPRP_BINARY_CFG_REPLAY_FAILED

3-Error

System could not apply binary startup-config error: [chars]

During reload system uses binary startup configuration. A valid binary configuration file reduces the overall boot time significantly. This message indicates that system failed to apply binary-configuration.

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MCPRP_BINARY_CFG_DEL_FAILED

3-Error

System could not delete binary startup-config error: [chars]

Each time that you erase startup-config binary-config is also erased. This message indicates that system failed to erase binary-configuration.

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_NOT-3-MCPRP_BINARY_CFG_GEN_FAILED

3-Error

System could not generate binary startup-config error: [chars]

Each time that you save running-config to startup-config a binary file is created and the ASCII file is updated. A valid binary configuration file reduces the overall boot time significantly. This message indicates that system failed to generate binary-configuration.

polaris-mgbl-infra

LOG_STD_ACTION

IOSXE_RP_CFG_INFO-6-MCPRP_BINARY_CFG_APPLIED

6-Information

System configuration : Binary

System is using binary config during startup

polaris-mgbl-infra

LOG_NO_ACTION

IOSXE_RP_CFG_INFO-6-MCPRP_ASCII_CFG_APPLIED

6-Information

System configuration : ASCII

System is using ASCII config during startup

polaris-mgbl-infra

LOG_NO_ACTION

IOSXE_SDWAN_CONFIG-3-MASTER_KEY_MISSING

3-Error

Type 6 master key is missing. A new key will be generated.

-

cedge-dfp

LOG_NO_ACTION

IOSXE_SDWAN_CONFIG-5-MASTER_KEY_PRESENT

5-Notice

Type 6 master key is present on the device.

A type 6 key encryption has been requested by config-manager and an existing type 6 master key will be used for encryption/decryption.

cedge-dfp

LOG_NO_ACTION

IOSXE_SDWAN_CONFIG-4-MASTER_KEY_GENERATED

4-Warning

A new type 6 encryption master key has been generated.

A type 6 encryption master key was not found on this device. A new key has been generated.

cedge-dfp

LOG_NO_ACTION

IOSXE_SDWAN_CONFIG-2-MASTER_KEY_FAILED

2-Critical

A new type 6 encryption master key has failed to generate

A type 6 encryption master key was not found on this device. A new key failed to generate.

cedge-dfp

LOG_STD_DDTS_TAC_DETAILS

IOSXE_SDWAN_CONFIG-4-KEY_ENCRYPT_CHANGE

4-Warning

A type 7 key was detected for [chars] which supports type 6. Re-encrypting to type 6.

A type 7 key was configured. Type 7 usage is discouraged when the component also supports type 6. The type 7 key will be descripted and re-encrypted to type 6.

cedge-dfp

LOG_NO_ACTION

IOSXE_RP_SPA-3-SEND_NGIO_MSG_FAIL

3-Error

NGIO Module message send failed for slot [dec] subslot [dec]

Failed to send ngio msg to iomd.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-MAC_FILTER_ADD_FAIL

3-Error

All the available [dec] mac filters for [chars] have been consumed. Failed to add [enet] for interface [chars]

The hardware cannot support any more filters.

DDTS_COMPONENT

"The interface configuration should be reworked " "to not cross the limit set by the hardware." "If the error is still seen please " LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-SEND_L2_HDR_MSG_FAIL

3-Error

slot [dec] subslot [dec]

Failed to send ngio L2 header to iomd.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-NO_HOST_INFO

3-Error

slot [dec] subSlot [dec] spaType 0x[hec]

Failed to get information about the host linecard.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-MAX_SPA

3-Error

Power to IPSEC-SPA-2G in [chars] is denied because it has exceeded the number allowed[dec]

The number of IPSEC-SPA-2G in a chassis is limited. This message is displayed when the number of IPSEC-SPA-2G in the chassis has exceeded this limit.

DDTS_COMPONENT

"Use only the number of supported IPSEC-SPA-2G"

IOSXE_RP_SPA-3-SPA_NO_HOST_INFO

3-Error

slot [dec] subSlot [dec] PID [chars]

Failed to get information about the host linecard.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-HWIDB_FAILURE

3-Error

Creation: slot [dec] subSlot [dec] port [dec] vc [dec]

Failed to create an interface hwidb.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-INVALID_PORT_NUM

3-Error

slot=[dec] port=[dec] hwidbType=0x[hec] max_port_num=[dec] LCtype=0x[hec]

The port number is out of range.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-4-SPA_RESP_CMD_MISMATCH

4-Warning

[chars]: Expecting response to interface configuration command [dec] but received response to command [dec].

An internal synchronization error occurred while configuring the interface. The configuration may not have succeeded.

DDTS_COMPONENT

"Check that the running configuration for the " "interface is correct. If this message occurred on the standby try " "reloading the standby to ensure that its configuration is in sync. " "If this message is repeatable please " LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-6-CARDRELOAD

6-Information

Module [dec] reload due to SPA insert in [dec]/[dec].

When inserting a SPA on this carrier card the card is reset.

-

LOG_STD_NO_ACTION

IOSXE_RP_SPA-6-CTRLRSWITCH

6-Information

switching controller type from [chars][dec] to [chars][dec] for subslot [dec]/[dec].

When IOSXE-SIP40 is inserted in the slot previously occupied by IOSXE-SIP10 or vice-versa the controller type of the card is overwritten to reflect the current SIP.

-

LOG_STD_NO_ACTION

IOSXE_RP_SPA-4-SPA_CMD_NO_RESP

4-Warning

[chars]: No response for interface configuration command [dec]

A timeout occurred while RP was waiting for a response from line card. This may happen due to line card CPU being too busy to respond to the command.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The RP failed to allocate a buffer for communication with a SPA

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-DPIDX_LKUP_FAIL

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-FLOWID_ALLOC_FAIL

3-Error

Failed to allocate a flow control identifier for interface [chars]

The SPA driver is not able to allocate the datapath flow control identifier for the interface specified in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-FLOWID_RELEASE_FAIL

3-Error

Failed to release a flow control identifier for interface [chars] status = [dec]

The SPA driver is not able to release the datapath flow control identifier for the interface specified in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-VC_PROV_FAIL

3-Error

Failed to provision interface [chars]

The SPA driver is not able to provision the interface specified in the message. Verify that the SPA hardware is not provisioned above the supported limit. Otherwise this indicates a hardware error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-CI_UPDATE_FAIL

3-Error

Failed to update connection identifier for interface [chars]

The SPA driver is not able to update the datapath connection identifier for the interface specified in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-NULL_DATA_STRUCTURE

3-Error

common_str_empty_str

A SPA driver is not able to retrieve the data structure mentioned in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-HWIDB_INIT_FAIL

3-Error

Failed to initialize data structure for SPA port [dec]/[dec]/[dec]

A SPA driver was not able to properly initialize a data structure mentioned in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-ERROR

3-Error

common_str_empty_str

This message can take many forms. It provides information about a\n\ software error.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-ERROR_INFO

3-Error

common_str_empty_str

This message can take many forms. It provides information about a\n\ software error without traceback.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-LCLOG_TOOLONG

4-Warning

Message too long from slot [dec]/[dec]: [dec] bytes

The SPA module passed down a logger message that is too long for\n\ the RP to handle.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-LCLOG_PARSE_ERR

4-Warning

Error parsing logger message: [chars] from subslot [dec]/[dec]

The SPA module passed down a logger message that could not be parsed.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-BAD_IFCOMTYPE

3-Error

Bad ifcom message type=[dec]

A SPA module passed down a message that the RP software\n\ was not prepared to handle.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-IPCFAILED

4-Warning

IPC failed to send RPC message to SPA module

The RP failed to send an RPC message via IPC to a SPA module.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-FOREVER

3-Error

cmd [dec] to [chars] slot [dec]/[dec] took [dec] usecs done [hec]

A CCB command from the RP to a SPA module took longer than expected.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-SEMAHOG

4-Warning

Process [dec] [chars] hogging [chars]! calling proc [dec] [chars]

-

-

-

IOSXE_RP_SPA-3-IPCPORTFAIL

3-Error

Failed to open IPC port '[chars]' with error [chars]

The RP failed to open a port for communication with a SPA\n\ module.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-CCB_PLAYBACK_ERROR

4-Warning

CCB playback failed for slot [dec].

The High Availability component for SPA modules failed to synchronize some new state information for the specified slot.

DDTS_COMPONENT

"Reload the standby supervisor module to force a fresh bulk " "synchronization. If this error recurs " LOG_STD_ACTION

IOSXE_RP_SPA-4-CCB_RECORD_ERROR

4-Warning

CCB record failed for slot [dec].

The High Availability component for SPA modules failed to record some new state information for the specified slot.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The RP failed to send a message to a SPA module.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-IFCFG_NO_UNIQUE_KEY

3-Error

No unique-key generator registered for interface configuration command [dec].

The High Availability component for SPA modules is unable to properly synchronize state information for the current configuration.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-IFCFG_FOREVER

3-Error

to [chars] slot [dec]/[dec] took [dec] usecs ret_val %lu

A interface config command from the RP to a SPA module took\n\ longer than expected.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-IFCFG_CMD_TIMEOUT

4-Warning

Interface configuration command 0x[hec] to slot [dec]/[dec] timed out

The RP sent an configuration command to the slot specified in the error message and received no confirmation for the command.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-IFCFG_CMD_NOT_OWNER

3-Error

Process '[chars]' waiting for interface configuration command 0x[hec] to

A process on the RP sent an configuration command to the slot specified in the error message and a different process waited for the result. This could cause incorrect line card configuration states.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-IFCFG_DFLT_LIST_ERROR

4-Warning

For Interface Configuration command [dec] default retval list search resulted 0x[hec] for slot [dec]/[dec]

The High Availability component for SPA modules failed to synchronize some new state information for the specified slot.

DDTS_COMPONENT

show platform redundancy \ if-config default-retvals

IOSXE_RP_SPA-4-IFCFG_PLAYBACK_ERROR

4-Warning

Interface Configuration command [dec] playback failed for slot [dec]/[dec].

The High Availability component for SPA modules failed to synchronize some new state information for the specified slot.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-IFCFG_RECORD_ERROR

4-Warning

Interface Configuration command [dec] record failed for slot [dec]/[dec].

The High Availability component for SPA modules failed to record some new state information for the specified slot.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-4-INCR_CFG_SYNC_FAIL

4-Warning

[chars] incremental running-config sync for [[dec]/[dec]] failed - [chars][dec]

The specified IOSXE incremental running-config sync failed

DDTS_COMPONENT

"Power cycle the redundant supervisor"

IOSXE_RP_SPA-3-IPCPORT

3-Error

Failed to [chars] IPC port '[chars]' error [chars]

The standby has failed to notify the active that its bulks\n\ synchronization of the SPA TSM has completed. The resultant action\n\ taken by the standby route processor is an attempt to resynchronize.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-VC_FLOWID_ALLOC_FAIL

3-Error

Failed to allocate a flow control identifier for VC [dec] under interface [chars]

The SPA driver is not able to allocate the datapath flow control identifier for the VC/interface specified in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-3-VC_INGID_ALLOC_FAIL

3-Error

Failed to allocate a ingress identifier for VC [dec] interface [chars]

The SPA driver is not able to allocate the datapath ingress identifier for the VC/interface specified in the message. This indicates a software error.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_RP_SPA-4-SPA_RESP_CMD_ERR

4-Warning

[chars]: Received response to interface configuration command [chars] with wrong return value [dec].

An internal error occurred while configuring the interface. The configuration may not have succeeded.

DDTS_COMPONENT

"Check that the running configuration for the " "interface is correct. If this message is repeatable please " LOG_STD_SH_TECH_ACTION

IOSXE_RP_SPA-3-FRR_CFG_REC_FAIL

3-Error

Failed to record fast reroute conifguration on [chars]: [chars]

This message is displayed when a fast reroute configuration is not properly recorded.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-MISSING_SPA_PKG_ERR

3-Error

sipspa[chars] package is not installed for slot = [dec] and subslot = [dec] SPA bootup failed.

This message is displayed when attempting to bootup a SPA without installing a subpackage required for the same.

-

"Download the sub-package required for the " "affected SPA from the Cisco CCO software download site and install " "the same. This SPA can be booted in sub-package mode only. Please " "refer to the Cisco ASR platform documentation for " "obtaining and installing sub-packages."

IOSXE_RP_SPA-3-UNSUPPORTED_SRVCS_SPA

3-Error

Service SPA %#X in [dec]/[dec] is not supported. SPA bootup failed.

This message is displayed when attempting to bootup any service SPA in router running non K9 image i.e. non-crypto image.

-

"Download the K9 IOS XE sub-packages and the " "required sub-package for the given service SPA from the Cisco CCO " "software download site and install the same. This SPA can be booted " "in sub-package mode only. Please refer to the Cisco ASR platform " "documentation for obtaining and installing sub-packages."

IOSXE_RP_SPA-3-MISSING_SPA_PKG_WARN

3-Error

sipspa[chars] package is not installed in standby for slot = [dec] and subslot = [dec].

This message is displayed in standby console when attempting to bootup or restart or reload a WMA SPA without installing a subpackage in the standby RP although the SPA is or will be operational due to prior wma spa package installation in active RP. If switchover takes place the WMA SPA will still be operational. But any subsequent soft or hard oir of the SPA will fail due to missing sub package required to boot up the SPA. Hence it is recommended to complete the wma spa package installation in standby also before switchover or immidiately after switchover.

-

"Download the sub-package required for the " "affected SPA from the Cisco CCO software download site and install " "the same for the standby RP as is done on active RP. Please refer " "to the Cisco ASR platform documentation for obtaining and installing " "sub-packages."

IOSXE_RP_SPA-3-SPA_WRONGTYPE

3-Error

Mismatched SPA type [dec] in slot [dec]/[dec]. Expected type [dec].

The SPA inserted does not match the currently provisioned SPA type.

-

"Replace wrong SPA with currently provisioned SPA type or type 'no card' " "to allow new card type to be discovered."

IOSXE_RP_SPA-6-MEDIA_AUTOFAILOVER

6-Information

Media Fail over from [chars] to [chars]

Gige Media Failover.

-

"This is inforamtional message Not an error message." "Use 'show interface gig'" "to see the current active media type."

ASR900INTF-3-UNSUPPORTED

3-Error

Interface [chars] is not supported in subslot [dec] by the [chars] module

The Interface specified in the error message is not supported in the specified Subslot by the version of the operating system currently running on the system.

-

-

ASR900IM-3-INCOMPATIBLE

3-Error

[chars]-[dec]

P1D and onwards Cu IM.... is not backward compatible with P1A/P1B/P1C Cu IM use the same build of Cu IM or reload the router to use the new build.

-

-

ASR900IM-3-UNSUPPORTED

3-Error

This Interface Module is not supported in subslot [dec]

The inserted IM is not supported in the specified subslot. Kindly check the supported slots for the IM type.

-

-

ASR900IM-3-UNSUPPORTED_PLATFORM

3-Error

This Interface Module is not supported in [chars] platform

The inserted IM is not supported in the specified platform

-

-

ASR900IM-3-DIFF_IM_INSERTED

3-Error

[chars] - [chars] in bay [dec]

A different IM type has been inserted in the bay which previously had another IM type. If the interfaces were set to default before swap the IM will boot up fine. If not IM will goto Out-of-service state. Kindly insert the previous IM type use hw-module subslot 0/x default and then proceed with the IM swap. If not might need to reload the box for recovery

-

-

ASR900IM-3-INVALID_COMBINATION

3-Error

[chars] is not allowed in bay [dec] can be supported only in bays [chars]

The inserted IM is not supported in the specified subslot given the combination of existing IMs in the chassis.

-

-

ASR900IM-3-INVALID_MODE

3-Error

[chars] with mode [chars] is not allowed in bay [dec] can be supported only in bays [chars]

The inserted IM is not supported in the specified subslot given the combination of existing IMs in the chassis.

-

-

ASR900IM-3-UNSUPPORTED_IPSEC

3-Error

[chars] will not be operational in subslot [dec] after reboot due to payload encryption support with IPsec license

The inserted IM will not be supported in the specified subslot after reboot due to payload encryption support with IPsec license. Kindly check the supported slots for the IM type.

-

-

ASR900IM-3-UNSUPPORTED_DYING_GASP

3-Error

Command rejected Cannnot co-exist with [chars] present in subslot [dec]. Please retry after removing IM and rebooting.

The inserted IM cannot co-exist in the specified subslot after enabling dying gasp internal port. Kindly check the supported slots for the IM type.

-

-

NCS4200INTF-3-UNSUPPORTED

3-Error

Interface [chars] is not supported in subslot [dec] by the [chars] module

The Interface specified in the error message is not supported in the specified Subslot by the version of the operating system currently running on the system.

-

-

NCS4200IM-3-INCOMPATIBLE

3-Error

[chars]-[dec]

P1D and onwards Cu IM.... is not backward compatible with P1A/P1B/P1C Cu IM use the same build of Cu IM or reload the router to use the new build.

-

-

NCS4200IM-3-UNSUPPORTED

3-Error

This Interface Module is not supported in subslot [dec]

The inserted IM is not supported in the specified subslot. Kindly check the supported slots for the IM type.

-

-

NCS4200IM-3-UNSUPPORTED_PLATFORM

3-Error

This Interface Module is not supported in [chars] platform

The inserted IM is not supported in the specified platform

-

-

NCS4200IM-3-DIFF_IM_INSERTED

3-Error

[chars] - [chars] in bay [dec]

A different IM type has been inserted in the bay which previously had another IM type. If the interfaces were set to default before swap the IM will boot up fine. If not IM will goto Out-of-service state. Kindly insert the previous IM type use hw-module subslot 0/x default and then proceed with the IM swap. If not might need to reload the box for recovery

-

-

NCS4200IM-3-INVALID_COMBINATION

3-Error

[chars] is not allowed in bay [dec] can be supported only in bays [chars]

The inserted IM is not supported in the specified subslot given the combination of existing IMs in the chassis.

-

-

NCS4200IM-3-INVALID_MODE

3-Error

[chars] with mode [chars] is not allowed in bay [dec] can be supported only in bays [chars]

The inserted IM is not supported in the specified subslot given the combination of existing IMs in the chassis.

-

-

IOSXE_RP_SPA-3-SONET_ALARM_PROC_ERR

3-Error

[chars] Error has occurred while processing in the sonet alarm-proc

Either free/create of the memory failed in SONET alarm proc

-

-

IOSXE_RP_SPA-3-LIC_REQ_FAILED

3-Error

[dec]/[dec]/[dec]: Interface enable not allowed - license request failed err=[hex]

A 10 Gig License is required to enable this port. License request has been denied by license manager

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-LIC_REL_FAILED

3-Error

[dec]/[dec]/[dec]: Failed to release license feature [chars] handle=0x[hec] err=[hex]

License release has been denied by license manager

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-LIC_REG_FAILED

3-Error

[dec]/[dec]/[dec]: Failed to register license feature [chars] err=[hex]

License registration has been denied by license manager

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-0-INVALID_ETHERNET_MSG_HANDLER_FVT

0-Emergency

Invalid Ethernet Message handler Function Vector Table for [chars] Module [dec]/[dec]

TDL Message handler vector table is not registered for Ethernet Module

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-INVALID_ETHERNET_MSG_HANDLER

3-Error

Invalid Message Handler for [chars] on [dec]/[dec] [chars] Module

TDL Message handler is not registered for Ethernet Module

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_RP_SPA-3-IOMD_CONFIG_FAIL

3-Error

The IOMD return value for BAY: [dec] CMD [dec]: code:%0x msg:[chars]

Failed to configure in IOMD.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

GR_IOS_DB-3-DB_EXIST

3-Error

Persist DB [chars][dec] not deleted!!!\n

GR_IOS_DB was not deleted from boot flash!

-

GR_IOS_DB_ERR_ACTION

GR_IOS_DB-3-PATH_FAILED

3-Error

Failed to get database path for [chars]\n

Failed to get database path.

-

GR_IOS_DB_ERR_ACTION

GR_IOS_DB-3-OPEN_DB

3-Error

Failed to open path: [chars] handle: 0x[hec] err: [chars] [dec]\n

Failed to open GR_IOS_DB database

-

GR_IOS_DB_ERR_ACTION

GR_IOS_DB-3-VFT_SET

3-Error

Failed to set VFT path: [chars] handle: 0x[hec] err: [chars] [dec]\n

Failed to set VFT for GR_IOS_DB database

-

GR_IOS_DB_ERR_ACTION

IOSXE_UTD-3-ALLOC

3-Error

Failed to allocate message

When attempting to program the dataplane there was not enough memory to allocate the message.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-3-MESSAGE

3-Error

Failed to send message

When the message was being prepared for sending to the data plane there was an error.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-VERSION_INCOMPATIBILITY

4-Warning

UTD package version \[chars]\ does not match recommended UTD package version \[chars]\

The UTD package version does not match the recommended UTD package version embedded in this IOS-XE version.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-2-VERSION_UNSUPPORTED

2-Critical

UTD package version \[chars]\ is not supported recommended version is \[chars]\

The UTD package version does not match the required UTD version embedded in this IOS-XE version. This is an unsupported configuration and may behave unexpectedly.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-OVA_DEPRECATION

4-Warning

The UTD OVA is being deprecated in an upcoming release. Please migrate to IOX to use the UTD TAR

The UTD OVA is being deprecated in an upcoming release. Support for the virtual-service command suite will end. To use UTD going forward please migrate to IOX infrastructure. See the 'Migrating to IOx Container' section on the following link for more information: http://cs.co/UtdSnortIPS

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-SIG_UPDATE_CFG

4-Warning

UTD signature updates have been configured - A brief service interruption at the time of update is expected

The UTD service will be restarted if a new signature package is found. During this time if fail-close has been configured recommended traffic that would be inspected by

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-SIG_UPDATE_EXEC

4-Warning

UTD signature update has been executed - A brief service interruption is expected

The UTD service will be restarted if a new signature package is found. During this time if fail-close has been configured recommended traffic that would be inspected by

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-SIG_UPDATE_CFG_INCOMPLETE

4-Warning

UTD signature update configuration is incomplete

UTD signature updates have been partially configured. Both the signature update server and occur-at frequency are required.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-MT_CONFIG_DOWNLOAD

4-Warning

UTD MT configuration download has [chars]

In UTD multitenancy mode the configuration download to the container can take a while. Please be patient.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-MT_CONTAINER_MESSAGE_TIMEOUT

4-Warning

UTD message sent to the container has timed out

The UTD message sent to the container has timed out.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-MT_CONTAINER_MESSAGE_NAK

4-Warning

Container responded to UTD message with an error: [dec]

The container rejected the UTD message

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-MT_CONTAINER_SESSION_TIMEOUT

4-Warning

UTD container download has timed out

The container did not respond with an up/down status before the session timed out.

iosxe-utd

LOG_STD_ACTION

IOSXE_UTD-4-MT_CONTAINER_STATUS_DOWN

4-Warning

UTD poll: container status is DOWN

The container sent a down status to the poll message

iosxe-utd

LOG_STD_ACTION

CCK_QAT-3-INIT_FAIL

3-Error

[chars]: initialization failed [chars]

CCK QAT initialization sequence failed.

iosxe-ipsec

"Copy the error message exactly as it appears and report it to your \n\ technical support representative."

IOSXE_MGMTVRF-3-PROCESS_CREATE_FAIL

3-Error

Management VRF process creation failed [chars]

Can not create IOS process for mgmt port init

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_MGMTVRF-3-VRF_CREATE_FAIL

3-Error

Management VRF creation failed [chars]

Can not create mgmt vrf during system init

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_MGMTVRF-3-AFI_ATTACH_FAIL

3-Error

Management VRF AFI [chars] attach failed

Can not create afi subblock for mgmt vrf

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_MGMTVRF-3-INTF_ATTACH_FAIL

3-Error

Management VRF attach to mgmt [chars] failed

Can not associate mgmt port to mgmt vrf

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_MGMTVRF-3-SET_TABLEID_FAIL

3-Error

Installing [chars] Management interface tableid 0x[hec] failed

Fail to set mgmt port tableid into Linux kernel

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO

6-Information

Management vrf [chars] created with ID [dec] ipv4 table-id 0x[hec] ipv6 table-id 0x[hec]

mgmt vrf and ipv4 ipv6 tables created for mgmt port

iosxe-iosd-infra

-

IOSXE_RP_EWLC_NOT-2-MSGTDLINITERROR

2-Critical

eWLC startup module initialization failed: Unable to initialize messaging: [chars]

The eWLC startup subsystem has failed to initialize the infrastructure for messaging with the Pluggable Services Daemon. Notification of configuration to critical modules cannot proceed.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_EWLC_NOT-2-MSGIPCINITERROR

2-Critical

Error initializing IPC queue

An unexpected condition in which IOS could not initialize\n\ a message queue to the PSD.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_EWLC_NOT-2-MSGTDLERROR

2-Critical

Error processing TDL message. [dec]

An unexpected condition in which IOS has received a TDL \n\ message which it can not process.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_EWLC_NOT-2-EWLC_STARTUP

2-Critical

Starting EWLC process [dec]

Sending TLD message to start up all eWLC processes

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_PLATFORM_RESOURCE_DCA-3-DCA_ENABLE_FAIL

3-Error

Platform Resource Dynamic Core Allocation Failure

An unexpected error occurred during attempt to dynamically apply a platform resource template configuration. System reboot required.

iosd-infra

"Reboot the system"

IOSXE_PLATFORM_RESOURCE_DCA-5-DCA_ENABLE_NOTICE

5-Notice

Platform Resource profile [chars] : [chars]

Informational message to indicate the start and completion of dynamically applying platform resource template configuration.

iosd-infra

LOG_STD_ACTION

PLOGDRP-3-MSGDISPATCHNULL

3-Error

Received NULL TDL message

An unexpected condition in which IOS has received a NULL TDL message for the Proxy Logger.

iosxe-plog

LOG_STD_ACTION

PLOGDRP-4-MSGDISPATCH

4-Warning

Unable to dispatch received TDL message '[chars]' from Proxy Logger. LUID: [chars]

An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages from Proxy Logger.

iosxe-plog

LOG_STD_ACTION

PLOGDRP-3-MSGDISPATCHERR

3-Error

Error when receiving TDL error message: [chars]

An unexpected condition in which IOS has received an error during TDL message processing from the Proxy Logger.

iosxe-plog

LOG_STD_ACTION

PLOGDRP-3-MSGINVALIDFIELD

3-Error

Invalid errmsg field '[chars]' received from the Proxy Logger error [dec]

An error message received from the Proxy Logger is missing a required field.

iosxe-plog

LOG_STD_ACTION

PLOGDRP-3-MSGBIPCBUFFER

3-Error

Unable to acquire a BIPC buffer for sending messages.

A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed.

iosxe-plog

LOG_STD_ACTION

PLOGDRP-3-MSGDISPATCHERR_SIZE

3-Error

Received TDL error message is larger than supported size :[dec]

A TDL message larger than supported has been received and partial message of that is displayed.

iosxe-plog

LOG_STD_ACTION

IOSXE_QFP-2-LOAD_EXCEED

2-Critical

Slot: [dec] QFP:[dec] Load [dec]%% exceeds the setting threshold [dec]%%.\n 5 secs traffic rate on QFP: Total Input: %llu pps %llu.%llu kpps %llu bps %llu.%llu mbps

QFP Load exceeds setting threshold.

-

"Monitor the traffic load."

IOSXE_QFP-2-LOAD_RECOVER

2-Critical

Slot: [dec] QFP:[dec] Load [dec]%% recovered.\n 5 secs traffic rate on QFP: Total Input: %llu pps %llu.%llu kpps %llu bps %llu.%llu mbps

QFP Load recovered.

-

"No action required normal operation."

YANG_INFRA-3-ENABLE_ONEP

3-Error

Error enabling onep

An error has occurred when attempting to enable onep.

polaris-dmi-infra

LOG_STD_ACTION

YANG_INFRA-3-DISABLE_ONEP

3-Error

Error disabling onep

An error has occurred when attempting to disable onep.

polaris-dmi-infra

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGDISPATCHNULL

3-Error

Received NULL TDL message

An unexpected condition in which IOS has received a NULL TDL message for Vty Management.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL messages for Vty Management

An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages for Vty Management.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGMISSINGFIELD

3-Error

Missing field '[chars]' in TDL Vty Management message '[chars]' received

A message missing a required field was received for Vty Management

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGINVALIDFIELDINT

3-Error

Invalid field '[chars]' in TDL message '[chars]' received: value '[dec]' for Vty Management

A message with an invalid field value was received for Vty Management

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGINVALIDFIELDSTR

3-Error

Invalid field '[chars]' value '[chars]' in TDL message '[chars]' received for Vty Management

A message with an invalid field value was received for Vty Management

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGERROR

3-Error

Error '[dec]' handling a received TDL message '[chars]' for Vty Management: [chars]

An unexpected condition has occurred while IOS is processing a received Vty Management TDL message

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGBUILDERROR

3-Error

Error '[dec]' building TDL Vty Management message '[chars]': [chars]

An unexpected condition has occurred while IOS is building a TDL response message for Vty Management

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGMARSHALERROR

3-Error

Error '[dec]' marshaling TDL Vty Management message '[chars]': [chars]

An unexpected condition has occurred while IOS is marshaling TDL response message for Vty Management

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGENQUEUEERROR

3-Error

Error queueing TDL Vty Management message '[chars]'

An unexpected condition has occurred when IOS attempted to queue a TDL response message for Vty Management

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGBIPCERR

3-Error

Unable to process received BIPC messages for Vty Management error: [chars]

An unexpected condition has occurred while IOS was trying to process a received BIPC message for Vty Management.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGBIPCBUFFER

3-Error

Unable to acquire a BIPC buffer of length [dec] for sending messages.

A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGEXTAPPUPDATE

3-Error

Unable to update external application data for line '[dec]'

An attempt to update the external application for a line failed unexpectedly. The line update failed and if the line number specified is valid the line was released.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGVTYSVCINIT

3-Error

Unable to initialize the Vty Management service listen port

The platform IPC services failed to register the Vty Management service's need for a listen port. The Vty Management service will be unable to process requests. IOS services will be unavailable to external access methods.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-MSGVTYCOUNT

3-Error

Invalid vty count [dec] detected on initialization

Upon initialization the Vty Management subsystem checks that the number of available vtys for the platform is valid.

iosxe-shellmgr

LOG_STD_ACTION

IOSXE_RP_VTYMGT-3-SET_ACCESS_FAIL

3-Error

Installing LIIN interface access control failed

This error happens when the Vty Management subsystem failed to set the access control function for the LIIN possibly due to IOS out of memory or corruption. Persistent access features into IOS will not work.

iosxe-shellmgr

LOG_STD_ACTION

NG3K_OIR-3-BULK_SYNC

3-Error

[chars]

Bulk sync failure the reason for the failure will be provided in the string

platform-ha

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

NG3K_OIR-3-INVALID_MSG_RECEIVED

3-Error

Invalid [chars] message received

A message that is used for state synchronization was not received correctly. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR-3-MALLOC_FAILURE

3-Error

[chars]

Failed to allocated memory for a structure or event

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR-3-MAC_FAILURE

3-Error

Mac Failure

NULL MAC

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR-3-REG_FAILURE

3-Error

Message:[chars]Error:[dec]

Registration Failure

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR-3-FILE_OPEN_FAILURE

3-Error

File [chars] open failed

File Open failed

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR-3-OIR_FAILURE

3-Error

Message:[chars]Error:[dec]

OIR failures due to various reasons

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR_ISSU-3-INIT

3-Error

NG3K OIR ISSU client initialization failed at [chars] error [chars]

NG3K OIR ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

platform-ha

LOG_STD_SH_TECH_ACTION

NG3K_OIR_ISSU-3-TRANSFORM

3-Error

NG3K OIR ISSU client [chars] transform failed error [chars]

NG3K OIR ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the NG3K OIR state will not\n\ be indentical with the active unit.

platform-ha

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NG3K_OIR_ISSU-3-MSG_NOT_OK

3-Error

NG3K OIR ISSU client message [dec] is not compatible

NG3K OIR ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NG3K_OIR_ISSU-3-MSG_SIZE

3-Error

NG3K OIR ISSU client failed to get the message size for message [dec]

NG3K OIR ISSU client failed to calculate message size\n\ for the message specified. The NG3K OIR ISSU client will not\n\ be able to send message to the standby unit.

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NG3K_OIR_ISSU-3-SESSION

3-Error

NG3K OIR ISSU client [chars]

NG3K OIR ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

NG3K_OIR_ISSU-3-SESSION_UNREGISTRY

3-Error

NG3K OIR ISSU client failed to unregister session information. Error: [dec] [chars]

The NG3K OIR ISSU client failed to unregister session information.

platform-ha

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

NG3K_OIR_ISSU-3-SEND_FAILED

3-Error

NG3K OIR ISSU client failed to send a negotiation message error [dec]

NG3K OIR ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

NG3K_OIR_ISSU-3-BUFFER

3-Error

NG3K OIR ISSU client failed to get buffer for message error [dec]

NG3K OIR ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

NG3K_OIR_ISSU-3-CAPABILITY

3-Error

NG3K OIR ISSU client [chars]

NG3K OIR ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

NG3K_OIR_ISSU-3-POLICY

3-Error

NG3K OIR ISSU client message type [dec] is [chars]

NG3K OIR ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

platform-ha

"show issu session <client_id>"

NG3K_OIR_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

NG3K OIR ISSU client capability exchange result incompatible.

The NG3K OIR ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

platform-ha

"show issu negotiated capability <Session_ID>"

NG3K_OIR_ISSU-3-CAP_INVALID_SIZE

3-Error

NG3K OIR ISSU client capability list is empty.

The BG3K OIR ISSU client capability exchange list size\n\ is invalid.

platform-ha

"show issu capability entries <Client_ID>"

IOSXE_TIMESTAMP_ENGINE-4-ERROR

4-Warning

NULL

An unexpected condition has occurred.

asr900-ptp

LOG_STD_ACTION

IOSXE_TIMESTAMP_ENGINE-3-TSU_ERR

3-Error

An unexpected condition has occurred at module [chars]

An unexpected condition has occurred at the Interface Module TSU.

asr900-ptp

LOG_STD_ACTION

DYNCMD-3-MSGDISPATCHNULL

3-Error

Received NULL TDL message

An unexpected condition in which IOS has received a NULL TDL message for Dynamic Commands.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL messages for Dynamic Commands

An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages for Dynamic Commands.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGMISSINGFIELD

3-Error

Missing field '[chars]' in TDL message '[chars]' received from the Shell Manager

A message missing a required field was received from the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGINVALIDFIELDINT

3-Error

Invalid field '[chars]' in TDL message '[chars]' received: value '[dec]' for Dynamic Commands

A message with an invalid field value was received for Dynamic Command creation

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGINVALIDFIELDSTR

3-Error

Invalid field '[chars]' value '[chars]' in TDL message '[chars]' received for Dynamic Commands

A message with an invalid field value was received for Dynamic Command creation

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGERROR

3-Error

Error '[chars]' handling a received TDL message '[chars]' for Dynamic Commands

An unexpected condition has occurred while IOS is processing a received Dynamic Command TDL message

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGBUILDERROR

3-Error

Error '[dec]' building TDL message '[chars]' to send to the Shell Manager

An unexpected condition has occurred while IOS is building a TDL message to send to the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGMARSHALERROR

3-Error

Error '[dec]' marshaling TDL message '[chars]' to send to the Shell Manager

An unexpected condition has occurred while IOS is marshaling TDL message to send to the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGENQUEUEERROR

3-Error

Error queueing TDL message '[chars]' to send to the Shell Manager

An unexpected condition has occurred when IOS attempted to queue a TDL message to send to the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGBIPCERR

3-Error

Unable to process received BIPC messages for Dynamic Commands error: [chars]

An unexpected condition has occurred while IOS was trying to process a received BIPC message for Dynamic Commands.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-MSGBIPCBUFFER

3-Error

Unable to acquire a BIPC buffer for sending messages.

A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-TREETOP

3-Error

Unable to link top-level keyword '[chars]' into parse tree

IOS received a message to add a command into the CLI. The appropriate location to link in the command could not be found.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-TREETOPNOTKW

3-Error

The top-level parser transition '[chars]' is not a keyword

IOS received a message to add a command into the CLI. The top-level node must be a keyword node.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-FLAGSINUSE

3-Error

New feature flags list [dec] invalid while feature flags in use [dec]

IOS received a message to set the feature flags for the CLI. The message received to set the feature flags changed the number of feature flags which is unexpected. The message is ignored.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-FLAGSINVALID

3-Error

New feature flag list values [dec] different than expected [dec]

-

-

-

DYNCMD-3-NODEOUTOFSEQ

3-Error

Create node message received when in mode '[chars]'

IOS received a message to add a command node into the CLI. The message was received out of sequence

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-LINKOUTOFSEQ

3-Error

Create node message received when in mode '[chars]'

IOS received a message to add a command node into the CLI. The message was received out of sequence

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-NODETYPEUNKNOWN

3-Error

Create node message received for unknown node type '[dec]' '[chars]'

IOS received a message to add a command into the CLI. One of the command nodes to be created is of a type unknown to IOS

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-NODEDUPLICATE

3-Error

Create node message received for duplicate node '[dec]'

IOS received a message to add a command into the CLI. One of the command nodes to be created has an identifier of an existing node. The new node is ignored.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-LINKUNKNOWNNODE

3-Error

Link node message received for unknown node '[dec]'

IOS received a message to add a command into the CLI. One of the messages to link nodes referenced a node unknown to IOS

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-LINKUNKNOWNACCEPTNODE

3-Error

Link node message received for unknown accept [chars] node '[dec]'

-

-

-

DYNCMD-3-LINKUNKNOWNALTNODE

3-Error

Link node message received for unknown alternate node '[dec]'

IOS received a message to add a command into the CLI. One of the messages to link nodes referenced a node unknown to IOS

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-LINKINVALIDALT

3-Error

Link alternate node message received for node '[chars]' which cannot have an alternate.

IOS received a message to add a command into the CLI. One of the messages to link nodes instructed IOS to link nodes which would result in an invalid construction.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-LINKINVALIDTRANS

3-Error

Link transition '[chars]' message received for node '[chars]' which cannot have such a transition.

IOS received a message to add a command into the CLI. One of the messages to link nodes instructed IOS to link nodes which would result in an invalid construction.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-CHAINADDFAIL

3-Error

Parse chain link add failed for '[chars]'

An error has occurred when a dynamic command is being added to the IOS command set. The commands specified will not be available.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-CHAINDELFAIL

3-Error

Parse chain link delete failed for '[chars]'

An error has occurred when a dynamic command is being removed from the IOS command set. The commands specified will stil not be available.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-7-CMDSET_LOADED

7-Debug

The Dynamic Command set has been loaded from the Shell Manager

IOS has completed loading the set of commands published and processed by components running in packages other than the IOS package.

iosxe-shellmgr

LOG_STD_NO_ACTION

DYNCMD-7-CMDSET_UNLOADED

7-Debug

The Dynamic Command set from the Shell Manager has been unloaded

IOS has completed unloading the Dynamic Command set. This should only occur when a new package has been installed and should shortly be followed by a message indicating that the new Dynamic Command set has been loaded.

iosxe-shellmgr

LOG_STD_NO_ACTION

DYNCMD-3-INIT

3-Error

Dynamic command subsystem failed to initialize '[chars]'

Some features depend on portions of the dynamic command infrastructure. Such features will be unavailable.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_LOAD

3-Error

Failed to load '[chars]': [chars]

Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_SYMBOL

3-Error

Package [chars] incompatible: symbol '[chars]' is of type [chars] expected [chars]

Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_VALIDATE

3-Error

Failed to validate '[chars]': [chars]

Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_API

3-Error

Package interface failure for package '[chars]': [chars]

Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_INSTALL

3-Error

Failed to install '[chars]': [chars]

Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_ARGS

3-Error

Incorrect argument count for package '[chars]' operation '[chars]': [dec] not [dec]

An error has occurred loading the commandset for a newly installed package. The package is not compatible with the running IOS instance.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_ARG

3-Error

Incorrect argument type for package '[chars]' operation '[chars]': [chars] [dec]

-

-

-

DYNCMD-3-PKGINT_ARG_NUMBERVAL

3-Error

Invalid argument value for package '[chars]' operation '[chars]': [dec] [dec]

-

-

-

DYNCMD-3-PKGINT_ARG_OPAQUEVAL

3-Error

Invalid argument value for package '[chars]' operation '[chars]': %p [dec]

-

-

-

DYNCMD-3-PKGINT_OFFSET

3-Error

Invalid offset argument for package '[chars]' operation '[chars]': [chars] [dec]

-

-

-

DYNCMD-3-PKGNODE_ADD_FAIL

3-Error

Parse node add failed for package '[chars]' [chars] [dec]

-

-

-

DYNCMD-3-PKGHANDLER_FILE_WRITE

3-Error

Package '[chars]' failed to write: [chars] [chars]

-

-

-

DYNCMD-3-PKGHANDLER_FILE_REMOVE

3-Error

Package '[chars]' failed to remove: [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_DIR_CREATE

3-Error

Package integration failed to create directory: [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_DIR_OPEN

3-Error

Package integration failed to open directory: [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_DIR_REMOVE

3-Error

Package integration failed to remove directory: [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_DIR_MOVE

3-Error

Package integration failed to move directory: [chars] to [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_FILE_OPEN

3-Error

Package integration failed to open file: [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_FILE_REMOVE

3-Error

Package integration failed to remove: [chars] [chars]

-

-

-

DYNCMD-3-PKGINT_LOCK

3-Error

Failed to acquire package list lock for [chars]: [chars]

An error occurred when a configuration package was being installed or removed. This may indicate a timeout which may be a temporary condition.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_PKGLOCK

3-Error

[chars] failed to acquire package lock for [chars]

An error occurred when locking a configuration package. The package needs to be locked for processing configuration commands or timer-based processing of configuration data.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-3-PKGINT_UNLOCK

3-Error

Failed to release the package list lock: [chars]

An error occurred when a configuration package was being installed or removed. This should not occur.

iosxe-shellmgr

LOG_STD_ACTION

DYNCMD-7-PKGINT_INSTALLED

7-Debug

The command package '[chars]' has been succesfully installed

IOS has completed installation of the specified command package. Configuration commands for the package are now available.

iosxe-shellmgr

LOG_STD_NO_ACTION

DYNCMD-7-PKGINT_UNINSTALLED

7-Debug

The command package '[chars]' has been succesfully uninstalled

IOS has completed uninstallation of the specified command package. Configuration commands for the package are no longer available.

iosxe-shellmgr

LOG_STD_NO_ACTION

DYNCMD-3-PKGERR_LOG_FAIL

3-Error

Failed to log errors for package '[chars]'

An error has occurred updating the commandset for a newly installed package. The commands which failed to transfer could not be saved for further analysis.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGDISPATCHNULL

3-Error

Received NULL TDL message

An unexpected condition in which IOS has received a NULL TDL \n\ message from Shell Manager.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message '[chars]' from Shell Manager. LUID: [chars]

An unexpected condition has occurred while IOS is trying to dispatch\n\ to the TDL message handler functions for received TDL messages from \n\ Shell Manager.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGMISSINGFIELD

3-Error

Missing field '[chars]' in TDL message '[chars]' received from the Shell Manager

A message missing a required field was received from the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGINVALIDFIELDINT

3-Error

Invalid field '[chars]' in TDL message '[chars]' received: value '[dec]' from the Shell Manager

A message with an invalid field value was received from the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGINVALIDFIELDSTR

3-Error

Invalid field '[chars]' value '[chars]' in TDL message '[chars]' received from the Shell Manager

A message with an invalid field value was received from the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGERROR

3-Error

Error [dec] handling a received TDL message '[chars]' from the Shell Manager: [chars]

An unexpected condition has occurred while IOS is processing a TDL message received from the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGBUILDERROR

3-Error

Error [dec] building TDL message '[chars]' to send to the Shell Manager: [chars]

An unexpected condition has occurred while IOS is building a TDL message to send to the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGMARSHALERROR

3-Error

Error '[dec]' marshaling TDL message '[chars]' to send to the Shell Manager

An unexpected condition has occurred while IOS is marshaling TDL message to send to the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGENQUEUEERROR

3-Error

Error queueing TDL message '[chars]' to send to the Shell Manager

An unexpected condition has occurred when IOS attempted to queue a TDL message to send to the Shell Manager

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-BADREPLYJOBID

3-Error

Incorrect command reply job id %llu origin [chars] expecting %llu

-

-

-

SMANRP-3-CMDTOOLONG

3-Error

Interactive command too long

Instructions for command execution would result in creation of a command string that is beyond the maximum size.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-CMDBUILD

3-Error

Interactive command directive [dec] of [dec] failed

In processing a CLI command one of the instructions returned through the Shell Manager could not be turned into an interactive command for remote execution.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-CMDCONNECT

3-Error

Connection to local interactive relay failed: [chars]

Connecting to the local relay for an interactive command failed due to the reason indicated in the error message.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-CMDSEND

3-Error

Send interactive command to relay failed: [chars]

Sending the interactive command string to the local relay after the connection was established failed by the reason indicated in the error message.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGBIPCCONNERR

3-Error

Unable to register with the BIPC subsystem for connections to Shell Manager

IOS Shell Manager client code could not register with the BIPC communications infrastructure in order to establish a connection with the Shell Manager.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGBIPCERR

3-Error

Unable to process received BIPC messages from Shell Manager error: [chars]

An unexpected condition has occurred while IOS trying to process a received BIPC message from Shell Manager.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-MSGBIPCBUFFER

3-Error

Unable to acquire a BIPC buffer for sending messages.

A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-INVALIDCONNHANDLE

3-Error

Invalid connection handle [dec] referenced during command execution.

The execution of a CLI command which must communicate with Shell Manager for command execution has referenced a connection handle that is invalid. The CLI command execution will have failed.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-SMAN_INIT_WQ_FAIL

3-Error

Shell Manager client connection handler initialization failed: Unable to create [dec] of [dec] receiving queues.

The Shell Manager client has failed to create all of its receiving queues. Ability to execute some CLI commands will be severely restricted or non-existent.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-SMAN_INIT_CONN_FAIL

3-Error

Shell Manager client connection pool initialization failed: Unable to request creation of [dec] of [dec] connections.

The Shell Manager client has failed to create all of its connections to Shell Manager. Ability to execute some CLI commands will be severely restricted or non-existent.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-SMAN_HANDLER_QUEUE_NOTEMPTY

3-Error

Dynamic command handler exited foreground process with non-empty queue

The dynamic command handler which dispatches commands to the shell manager has exited without proper cleanup.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-SMAN_INIT_DC_TDL_FAIL

3-Error

Shell Manager client initialization failed: Unable to initialize messaging: [chars]

The Shell Manager client has failed to initialize the infrastructure for messaging with the Shell Manager. Ability to execute some CLI commands will be severely restricted or non-existent.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-3-SET_ACCESS_FAIL

3-Error

Installing LIIN interface access control failed

This error happens when the Shell Manager shim failed to set the access control function for the LIIN possibly due to IOS out of memory or corruption. Interactive commands will not work.

iosxe-shellmgr

LOG_STD_ACTION

SMANRP-6-SMSTATUS

6-Information

Shell Manager is [chars]

The current status of Shell Manager.

-

LOG_STD_NO_ACTION

SMANRP-3-MSGCRFTRELOADERROR

3-Error

Error sending CRFT capture on reload message.

IOS failed to successfully complete the CRFT reload archive operation.

polaris-crft

LOG_STD_ACTION

IOXN_APP-3-INITFAIL

3-Error

Failed to create chasfs property ioxman rc =[chars] or caf rc = [chars] is not up

-

-

-

IOXN_APP-3-CLEANUPFAIL

3-Error

Failed to create chasfs property to indicate cleanup of previous app installation rc = [chars]

-

-

-

IOXN_APP-3-GSFAIL

3-Error

[chars] [dec]

An unexpected condition resulted into failure to start an application.

iox-caf

LOG_STD_ACTION

IOXN_APP-3-CFGFAIL

3-Error

[chars] [chars]

An unexpected condition resulted into failure to apply auto config

iox-caf

LOG_STD_ACTION

IOXN_APP-3-PREVOPFAIL

3-Error

Overriding previous operation [chars] iox that is taking longer than [dec]

An unexpected condition resulted in failure to apply iox config

iox-caf

LOG_STD_ACTION

IOXN_APP-3-MSGFAIL

3-Error

Message dispatch failure [chars].

-

-

-

IOXN_APP-6-LICENCE_CHECK_INFO

6-Information

[chars]\n

Informational log about license.

-

LOG_STD_ACTION

IOXN_APP-6-STARTUP_CONFIG_INFO

6-Information

[chars]\n

Informational logs for startup config injection.

-

LOG_STD_ACTION

IOXN_APP-6-STARTUP_CONFIG_CHASSIS_INFO

6-Information

[chars] [dec]/[chars]/[dec]/[dec]\n

Chassis information at startup config injection.

-

LOG_STD_NO_ACTION

IOXN_APP-3-STARTUP_CONFIG_FAIL

3-Error

[chars] [chars]\n

Error while creating startup config

-

LOG_STD_ACTION

IOXN_APP-3-IOX_CONFIG_FAIL

3-Error

IOX configuration change not allowed while running\n

Error in iox configuration

-

LOG_STD_ACTION

IOXN_APP-3-IPCINITFAIL

3-Error

[chars]\n

A critical IPC initialization error occured

iox-caf

LOG_STD_ACTION

IOXN_APP-6-SLOT_NOTIFICATION

6-Information

[chars] [dec]

Slot addition or removal information

-

LOG_STD_NO_ACTION

IOXN_APP-6-PRE_INIT_DAY0_GS_INFO

6-Information

[chars]\n

Informational logs for Day0 GS initialization.

-

LOG_STD_ACTION

IOXN_APP-6-IOX_START_STOP_REQ

6-Information

[chars]\n

Informational logs for IOX Start/Stop request.

-

LOG_STD_ACTION

IOXN_APP-6-APP_HOSTING_SUPPORT

6-Information

[chars]

Informational logs to show App Gigabit Interface is not supported on 10 Slot Catalyst 9400

-

LOG_STD_ACTION

IOSXE_MMA_FMP-3-ENQUEFAIL

3-Error

Enqueue of TDL message failed [chars].

-

-

-

FMANRP_VRF-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

iosxe-nat

LOG_STD_ACTION

FMANRP_VRF-3-ENOMEM

3-Error

NULL

Not enough memory memory pre allocation failed

picasso-infra

LOG_STD_ACTION

FMANRP_VRF-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

iosxe-nat

LOG_STD_ACTION

FMANRP_ESS-3-ERREVENT

3-Error

[chars] [hex]

-

-

-

FMANRP_ESS-3-ERREVENT2

3-Error

[chars] [hex] / [hex]

-

-

-

FMANRP_ESS-4-WRNEVENT

4-Warning

[chars] [hex]

-

-

-

FMANRP_ESS-4-WRNEVENT2

4-Warning

[chars] [hex] / [hex]

-

-

-

FMANRP_ESS-4-WRNPARAM

4-Warning

[chars]

A failure has occured relating to an incorrect functional parameters.

iosxe-bb

" The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION

FMANRP_ESS-4-WRNPARAM_FU

4-Warning

[chars]: [chars] [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_U

4-Warning

[chars] [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_S

4-Warning

[chars]: [chars]

A failure has occured relating to an incorrect functional parameters.

iosxe-bb

" The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION

FMANRP_ESS-4-WRNPARAM_D

4-Warning

[chars] [dec]

-

-

-

FMANRP_ESS-4-SESSCNT

4-Warning

[chars] [hex]

-

-

-

FMANRP_ESS-4-WRNPARAM_F2X

4-Warning

[chars]: [chars] [hex] / [hex]

-

-

-

FMANRP_ESS-4-WRNPARAM_F2S

4-Warning

[chars]: [chars] [chars] / [chars]

-

-

-

FMANRP_ESS-4-WRNPARAM_XU

4-Warning

[chars] [hex] / [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_2U

4-Warning

[chars] [dec] / [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_DU

4-Warning

[chars] [dec] / [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_2X

4-Warning

[chars] [hex] / [hex]

-

-

-

FMANRP_ESS-4-WRNPARAM_3X

4-Warning

[chars] [hex] / [hex] / [hex]

-

-

-

FMANRP_ESS-4-WRNPARAM_2X2S

4-Warning

[chars] [hex] / [hex] / [chars] / [chars]

-

-

-

FMANRP_ESS-4-WRNPARAM_UXD

4-Warning

[chars] [dec] / [hex] / [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_2XD

4-Warning

[chars] [hex] / [hex] / [dec]

-

-

-

FMANRP_ESS-4-WRNPARAM_U2X

4-Warning

[chars] [dec] / [hex] / [hex]

-

-

-

FMANRP_ESS-4-SEGFAIL

4-Warning

[chars] Seghandle 0x[hec] of Type [dec]

A failure has occured with a segment operation.

iosxe-bb

" The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION

FMANRP_ESS-4-SEGFAIL2

4-Warning

[chars] Seghandle 0x[hec] of Type [dec] ess_segment= [hex]

A failure has occured with a segment operation.

iosxe-bb

" The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION

FMANRP_ESS-4-EVSICREAT

4-Warning

[chars] sip_ess_segment= [hex] segment_id= [dec] fsp_ess_segment= [hex] segment_id= [dec] evsi= [dec]

A failure has occured in creating a session interface.

iosxe-bb

" The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION

FMANRP_ESS-4-MAXSESS

4-Warning

[chars] [dec]

-

-

-

FMANRP_ESS-3-ENQUEFAIL

3-Error

[chars] [hex] [hex]

-

-

-

FMANRP_ESS-4-FULLVAI

4-Warning

Session creation failed due to Full Virtual-Access Interfaces not being supported. Check that all applied Virtual-Template and RADIUS features support Virtual-Access sub-interfaces. swidb= [hex] ifnum= [dec]

A failure has occured in creating a session interface due to a Full Virtual-Access Interface being created. Full Virtual-Access Interface are created if a Virtual-Template or RADIUS feature does not support Virtual-Access sub-interfaces. This platform only supports Virtual-Access sub-interfaces. Refer to Action to isolate offending feature.

iosxe-bb

" The session creation is rejected." " Steps to isolate unsupported Session feature:\n" " Run 'test Virtual-Template # subinterface' where" " # is the Virtual-Template number being used to" " create the session. Remove any identified" " features that are not sub-interface compliant.\n" " For RADIUS features:\n" " Configure \"aaa policy interface-config" " allow-subinterface\" on the router or\n" " cisco-avpair=\"lcp:allow-subinterface=yes\" needs" " to be specified in the subscriber profile on the" " Radius server."

FMANRP_PFR-4-NULLINPUT

4-Warning

NULL input [chars]

An unexpected condition has occurred which is due to the NULL value\n\ of the input parameter.

iosxe-pfr

"show oer border"

FMANRP_PFR-4-NOINTF

4-Warning

PfR Interface [chars] not exist can't be [chars]

An unexpected condition has occurred which is due to the absence of\n\ MCP PfR interface info.

iosxe-pfr

"show oer border"

FMANRP_PFR-4-UNSUPPORTED

4-Warning

Unsupported action [chars]

An unexpected condition has occurred which is due to and unsupported action being executed.

iosxe-pfr

"show oer border"

FMANRP_NETFLOW-3-CACHETDLMSGMARSHAL

3-Error

Failed to copy cache config message to IPC buffer for cache type [dec]

The operation of building a TDL message for cache configuration\n\ has failed.

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-AGGRCACHENULL

3-Error

The pointer for aggregation cache type [dec] is NULL

An unexpected condition has occurred which is due to the absence of\n\ an aggregation cache data structure.

iosxe-netflow

"show ip cache flow"

FMANRP_NETFLOW-3-UNKNOWNCACHETYPE

3-Error

Unknown cache type [dec] received

The cache configuration command has failed due to unknown\n\ cache scheme type.

-

LOG_STD_ACTION

FMANRP_NETFLOW-3-UNKNOWNCACHECMD

3-Error

Unknown aggregation cache command [dec] received

The aggregation cache configuration command has failed due to \n\ unknown command.

-

LOG_STD_ACTION

FMANRP_NETFLOW-4-NOSWIDB

4-Warning

Sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a swidb structure.

iosxe-netflow

"show ip interface"

FMANRP_NETFLOW-4-NOFIBIDB

4-Warning

fibdb for interface [chars] is null

An unexpected condition has occurred which is due to the absence\n\ of a fibidb structure.

iosxe-netflow

"show ip interface"

FMANRP_NETFLOW-3-IFFLOWTDLMSGMARSHAL

3-Error

Failed to copy interface flow config message to IPC buffer for [chars]

The operation of building a TDL message for interface flow configuration\n\ has failed.

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-NOSAMPLERNAME

3-Error

Sampler-map name is null

An unexpected condition has occurred which is due to the absence of\n\ a sampler-map name.

iosxe-netflow

"show sampler"

FMANRP_NETFLOW-3-NOSAMPLER

3-Error

Sampler for sampler-map name [chars] is null

An unexpected condition has occurred which is due to the absence of\n\ a sampler-map structure

iosxe-netflow

"show sampler"

FMANRP_NETFLOW-3-SAMPLERTDLMSGMARSHAL

3-Error

Failed to copy sampler-map config message to IPC buffer for [chars]

The operation of building a TDL message for sampler-map configuration\n\ has failed.

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-EXPORTERTDLMSGMARSHAL

3-Error

Failed to copy exporter config message to IPC buffer for cache \n\ type [dec]

The operation of building a TDL message for exporter configuration\n\ has failed.

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-4-EXPORTERVERSION

4-Warning

Failed to change default exporter version to [dec]

The operation of changing the default exporter version has failed.

iosxe-netflow

"show ip flow export"

FMANRP_NETFLOW-3-CLRSTATSTDLMSGMARSHAL

3-Error

Failed to copy clear statistics message to IPC buffer

The operation of building a TDL message for clearing statistics \n\ in the data path has failed.

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-STATSUPDTDL

3-Error

Failed to update netflow [chars] statistics

An unexpected condition has occurred when updating statistics

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-INVALIDFLOWDEFCPP

3-Error

CPP Flow definition can not be created [dec]

The operation of building a flow definition using flow fields received from CPP has failed.

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-EXPORTERSRCIFINVALID

3-Error

Management interface [chars] cannot be used as source for an exporter

Exporter configuration failed because the management interface cannot be configured as source interface

iosxe-netflow

LOG_STD_ACTION

FMANRP_NETFLOW-3-EXPORTERVRFINVALID

3-Error

Management vrf [chars] cannot be used as exporter destination

Exporter configuration failed because management vrf cannot be used as exporter destination

iosxe-netflow

LOG_STD_ACTION

FMANRP_EVPN-3-UNSPOP

3-Error

Unsupport operation

An unexpected operation is get during EVPN configuration

iosxe-evpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-STATSCLEARERR

3-Error

Unable to send clear WEB VPN context stats message. [chars] [dec]

This operation to build a TDL messages for WEB VPN context stats \n\ clearing has failed.

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-STATSGUPDERR

3-Error

Update WEB VPN context stats error. [chars] [dec]

An unexpected condition has occurred when updating global sslvpn \n\ statistics

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-STATSWVUPDERR

3-Error

[chars]: [chars]

An unexpected condition has occurred when updating ssl web vpn \n\ context statistics

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-CFGSTATUSERR

3-Error

[chars]: [chars]

An unexpected condition has occurred when got status of\n\ configuration

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-GWERR

3-Error

Failed [chars]: [chars]

An unexpected condition has occurred in configuration processing \n\ causing configuration failure.

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-VWCONFERR

3-Error

Failed [chars]: [chars]

An unexpected condition has occurred during WebVPN Context configuration\n\ causing failure.

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-PKIERR

3-Error

Failed [chars]: [chars]

An unexpected condition has occurred in configuration processing \n\ causing configuration failure.

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-AAATDLERR

3-Error

[chars][chars]. [chars]

An unexpected condition has occurred in processing AAA request/reply message causing AAA handling failure.

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-4-AAAFRIPWARN

4-Warning

[chars]Invalid framed ip address [inet] received from AAA. Not sending user config

Wrong AAA server config.

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-RRITDLERR

3-Error

[chars][chars]. [chars]

An unexpected condition has occurred in processing of SSLVPN route inject/remove message

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-RRICHUNKERR

3-Error

[chars]

Error has occurred when requested memory for SSLVPN route handling

iosxe-sslvpn

LOG_STD_ACTION

FMANRP_SSLVPN-3-CONDDEBERR

3-Error

[chars]. [chars]

An unexpected condition has occurred in processing conditional debug message

iosxe-sslvpn

LOG_STD_ACTION

PLATFORM_MATM-3-INVALID_MSG_RECEIVED

3-Error

MATM received invalid SPI message.

A messages that was to be received from the hardware module was not received correctly. Mac address learning/ageing might be impacted as a result. The failure most likely occurred because of a software communication error.

firmware

LOG_STD_SH_TECH_ACTION

PLATFORM_MATM-4-QUEUE_OVERLIMIT

4-Warning

MATM dropped [chars] messages as queue limit has reached.

Messages received from the hardware module were not processed because an internal queue was full. Mac address learning/aging might be impacted as a result.

firmware

LOG_STD_SH_TECH_ACTION

NGWC_FEC-3-BULK_SYNC

3-Error

[chars]

Bulk sync failure the reason for the failure will be provided in the string

platform-ha

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

NGWC_FEC-3-INVALID_MSG_RECEIVED

3-Error

Invalid [chars] message received

A message that is used for state synchronization was not received correctly. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_FEC-3-MALLOC_FAILURE

3-Error

[chars]

Failed to allocated memory for a structure or event

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_FEC-3-MAC_FAILURE

3-Error

Mac Failure

NULL MAC

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_FEC-3-REG_FAILURE

3-Error

Message:[chars]Error:[dec]

Registration Failure

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_FEC-3-FILE_OPEN_FAILURE

3-Error

File [chars] open failed

File Open failed

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_FEC-3-OIR_FAILURE

3-Error

Message:[chars]Error:[dec]

NGWC FEC failures due to various reasons

platform-ha

LOG_STD_SH_TECH_ACTION

PLATFORM_SPAN-5-NOSPANDATA

5-Notice

SPAN data not available during reconciliation

SPAN data not available after switchover for reconciliation. Use CLI 'show monitor' 'show platform monitor-fed' to check if the configuration is intact after switchover. This is not expected please log a defect message seen during bootup it indicates system trying

firmware

LOG_STD_ACTION

PLATFORM_PM-2-SPI_CHNL_NRDY

2-Critical

PM-SPI channel not ready yet slot: [dec]

PM SPI channel not ready for communication yet. Use CLI 'show platform pm spi-info' to check channel status. If message seen during bootup it indicates system trying to send SPI msgs too early bootup. Missed SPI messages will be lost and system may be in unstable state. Need to reboot to recover from the current state Note: Slot:0 indicates multicast SPI channel

firmware

LOG_STD_ACTION

PLATFORM_PM-2-BLK_WAIT_TOUT

2-Critical

PM wait for ack timed out: If [chars] dest slots:0x%X pending acks from boxes 0x%X

Time out happened while waiting for ack from driver process Possible reasons: \n1. SPI IPC communication failure

firmware

LOG_STD_ACTION

PLATFORM_PM-2-ASYNC_WAIT_TOUT

2-Critical

PM wait for ack timed out: req_id [dec] dest slots:0x%X ack pending from slots 0x%X

Time out happened while waiting for ack from driver process Possible reasons: \n1. SPI IPC communication failure

firmware

LOG_STD_ACTION

PLATFORM_PM-2-SPISNDFAIL

2-Critical

PM SPI msg send failed. If:[chars] Msg Type:[chars] Targets: 0x%X ec: [dec]

SPI msg send failed on PM SPI channel. Please look at error code ec and check if destination switch

firmware

LOG_STD_ACTION

PLATFORM_PM-0-SPI_FC_FAIL

0-Emergency

SPI-FC Failure while sending PM SPI msg[chars]. If:[chars] Msg Type:[chars] Targets: 0x%X spi-fc ec: [dec]

SPI-FC infra failed to service SPI msg transmit. Possibility coding error error code would help to know the reason for failure

firmware

LOG_STD_ACTION

PLATFORM_PM-2-INVAL_IFID

2-Critical

Invalid IIF Id: 0x%016llX assigned to if:[chars]

Port has invalid IIF Id assigned and hence SPI message to driver process FED can fail leaving system in unstable

firmware

LOG_STD_ACTION

PLATFORM_PM-5-INVAL_PMODE

5-Notice

Port Mode: [dec] is not supported type for If:[chars]

Unsuppoted port mode or invalid config.

firmware

LOG_STD_ACTION

PLATFORM_PM-1-RSC_FAIL

1-Alert

[chars]

Resource allocation failed. May need to reboot the system

firmware

LOG_STD_ACTION

PLATFORM_PM-1-SPI_CNCT_FAIL

1-Alert

SPI connect call failed. Slot: [dec] SPI RH: 0x%X error code: [dec]

Failure is due to SPI. System cannot function reliably further. Reboot may help

firmware

LOG_STD_ACTION

PLATFORM_PM-5-UNKNOWN_REQ

5-Notice

Ack received for unknown request from driver process FED.

Ack from driver process is received for the request id which is not in wait queue. This would be due to delayed ack after time out at IOSd.

firmware

LOG_STD_ACTION

PLATFORM_PM-2-SPI_ADDMCAST_FAIL

2-Critical

Add multicast group member failed. Group Handle: 0x%X remote handle: 0x%X error code:[dec]

SPI module problem. New handle is not added into multicast group handle. None of PM msgs would go to new switch driver process. Reboot newly added switch

firmware

LOG_STD_ACTION

PLATFORM_PM-2-NOIDB

2-Critical

No IDB exists for IIF id: 0x%016llX

IIF Id received in PM SPI msg from driver process FED is invalid and hence convertion to IDB fails. This would be due to interfaces deleted by the time IOSd receives the msgs. Please collect history of actions performed before hitting this error for further investigations.

firmware

LOG_STD_ACTION

PLATFORM_PM-2-NOHWIDB

2-Critical

IDB does not exist

HWIDB does not exist during SPAN configuration This would be due to IDB creation issue Please collect history of actions performed before hitting this error for further investigations.

firmware

LOG_STD_ACTION

PLATFORM_PM-5-NOPC

5-Notice

Port cookie pc does not exist for If: [chars]

Failed to get PM port_data subblock from IDB. Possible reason would be IDB is not supported by PM. If error is seen during bootup and if interfaces is PM supported it indicates trying to get PD prior to PM init completion

firmware

LOG_STD_ACTION

PLATFORM_PM-5-NOPD

5-Notice

No Port data PD exists for If: [chars]

Failed to get PM port_data subblock from IDB. Possible reason would be IDB is not supported by PM. If error is seen during bootup and if interfaces is PM supported it indicates trying to get PD prior to PM init completion

firmware

LOG_STD_ACTION

PLATFORM_PM-5-PDNOTPRESENT

5-Notice

No Port data PD exists

Port data does not exist. This should not happen. If this error is seen during switchover there is a likely race condition in creation/deletion of port data.

firmware

LOG_STD_ACTION

PLATFORM_PM-6-FRULINK_INSERTED

6-Information

[chars] uplink module inserted in the switch [dec] slot [dec]

A FRULink module has been inserted in the available slot.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-FRULINK_UNKNOWN_INSERTED

6-Information

Unsupported FRU module inserted in slot [dec]

The FRULink module inserted in the available slot is not supported.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-DOWNSHIFT

6-Information

Experienced Channel Quality Impairment on interface [chars] Downshifting Speed to [chars]

Speed Downshift Detected.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-FRULINK_UNKNOWN_REMOVED

6-Information

Unsupported FRU module removed from slot [dec]

The FRULink module removed from the slot is not supported.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-FRULINK_REMOVED

6-Information

[chars] uplink module removed from switch [dec] slot [dec]

The FRULink module inserted in the available slot has been removed.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-MODULE_INSERTED

6-Information

SFP module inserted with interface name [chars]

The SFP module has been inserted in the available slot.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-DIFFERENT_MODULE_INSERTED

6-Information

Warning: SFP module inserted in to the interface [chars] differs from the previously inserted one. The port's [chars] configuration will be set to the default.

A different SFP module has been inserted in the available slot. Previous configured duplex/speed will be set to default.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-MODULE_REMOVED

6-Information

SFP module with interface name [chars] removed

The SFP module inserted in the available slot has been removed.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-6-MODULE_ERRDISABLE

6-Information

The inserted SFP module with interface name [chars] is not supported

The SFP module inserted in the available slot has been removed.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-3-HOSTACCESSFAIL

3-Error

Unable to configure hardware to [chars] host access on [chars]. Port may not behave as expected.

The system was unable to configure the hardware to set the requested host access policy. There may be insufficient TCAM resources available.

firmware

"Stop all traffic issue clear mac-address-table " "dynamic and remove and re-issue the command that failed."

PLATFORM_PM-3-LOOP_BACK_DETECTED

3-Error

Loop-back detected on [chars].

Loop-back may be caused accidentally by \ plugging in a balun cable to the port.

firmware

"Check the cables. If a balun cable is connected and the " "loopback condition is desired no action is required. " "Otherwise connect the correct cable and bring the port up."

PLATFORM_PM-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD

3-Error

Collisions at [chars] exceed threshold. Considered as loop-back.

The collisions at a half-duplex port exceed the threshold and the port is considered as loop-back.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-5-OIR_CALLBACK_SYS_NOT_INIT

5-Notice

UDLD OIR Callback is invoked ahead of sys init complete

UDLD OIR Callback is invoked too early.

accsw-ha-infra

LOG_STD_ACTION

NGWC_FEC_ISSU-3-INIT

3-Error

NGWC FEC ISSU client initialization failed at [chars] error [chars]

NGWC FEC ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

platform-ha

LOG_STD_SH_TECH_ACTION

NGWC_FEC_ISSU-3-TRANSFORM

3-Error

NGWC FEC ISSU client [chars] transform failed error [chars]

NGWC FEC ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the NGWC FEC state will not\n\ be indentical with the active unit.

platform-ha

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NGWC_FEC_ISSU-3-MSG_NOT_OK

3-Error

NGWC FEC ISSU client message [dec] is not compatible

NGWC FEC ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NGWC_FEC_ISSU-3-MSG_SIZE

3-Error

NGWC FEC ISSU client failed to get the message size for message [dec]

NGWC FEC ISSU client failed to calculate message size\n\ for the message specified. The NGWC FEC ISSU client will not\n\ be able to send message to the standby unit.

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

NGWC_FEC_ISSU-3-SESSION

3-Error

NGWC FEC ISSU client [chars]

NGWC FEC ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

NGWC_FEC_ISSU-3-SESSION_UNREGISTRY

3-Error

NGWC FEC ISSU client failed to unregister session information. Error: [dec] [chars]

The NGWC FEC ISSU client failed to unregister session information.

platform-ha

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

NGWC_FEC_ISSU-3-SEND_FAILED

3-Error

NGWC FEC ISSU client failed to send a negotiation message error [dec]

NGWC FEC ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

NGWC_FEC_ISSU-3-BUFFER

3-Error

NGWC FEC ISSU client failed to get buffer for message error [dec]

NGWC FEC ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

NGWC_FEC_ISSU-3-CAPABILITY

3-Error

NGWC FEC ISSU client [chars]

NGWC FEC ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

NGWC_FEC_ISSU-3-POLICY

3-Error

NGWC FEC ISSU client message type [dec] is [chars]

NGWC FEC ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

platform-ha

"show issu session <client_id>"

NGWC_FEC_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

NGWC FEC ISSU client capability exchange result incompatible.

The NGWC FEC ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

platform-ha

"show issu negotiated capability <Session_ID>"

NGWC_FEC_ISSU-3-CAP_INVALID_SIZE

3-Error

NGWC FEC ISSU client capability list is empty.

The NGWC FEC ISSU client capability exchange list size\n\ is invalid.

platform-ha

"show issu capability entries <Client_ID>"

FMANRP_ALG-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

iosxe-alg

LOG_STD_ACTION

FMANRP_ALG-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

iosxe-alg

LOG_STD_ACTION

FMANRP_ACL-4-NOSWIDB

4-Warning

Sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a swidb structure.

iosxe-acl

"show ip interface"

FMANRP_ACL-4-NOSB

4-Warning

Subblock on interface [chars] 0x[hec] is null

An unexpected condition has occurred which is due to the absence of\n\ a subblock structure on interface.

iosxe-acl

"show ip interface"

FMANRP_ACL-4-NOACL

4-Warning

ACL is null

An unexpected condition has occurred which is due to the absence of\n\ an ACL structure.

iosxe-acl

"show ip access-list"

FMANRP_ACL-4-NOV4ACE

4-Warning

v4 ACE is null

An unexpected condition has occurred which is due to the absence of\n\ an v4 ACE structure.

iosxe-acl

"show ip access-list"

FMANRP_ACL-4-NOV6ACE

4-Warning

v6 ACE is null

An unexpected condition has occurred which is due to the absence of\n\ an v6 ACE structure.

iosxe-acl

"show ipv6 access-list"

FMANRP_ACL-4-NOMACACE

4-Warning

mac ACE is null

An unexpected condition has occurred which is due to the absence of\n\ an mac ACE structure.

iosxe-acl

"show access-list"

FMANRP_ACL-4-INVALIDV4ACETYPE

4-Warning

v4 ACE type is invalid

An unexpected condition has occurred which is due to the type of v4 ACE\n\ created

iosxe-acl

"show ip access-list"

FMANRP_ACL-4-INVALIDV6OP

4-Warning

Operation is invalid

An unexpected condition has occurred which is due to the operation \n\ performed

iosxe-acl

"show ipv6 access-list"

FMANRP_ACL-4-UPDV4STATSERR

4-Warning

Update v4 ACL statistics error

An unexpected condition has occurred when updating v4 ACL statistics

iosxe-acl

"show ip access-list"

FMANRP_ACL-4-UPDV6STATSERR

4-Warning

Update v6 ACL statistics error

An unexpected condition has occurred when updating v6 ACL statistics

iosxe-acl

"show ipv6 access-list"

FMANRP_ACL-4-UPDMACSTATSERR

4-Warning

Update mac ACL statistics error

An unexpected condition has occurred when updating mac ACL statistics

iosxe-acl

"show access-list"

FMANRP_ACL-4-TMPLACLINITERR

4-Warning

Template ACL initialization error

An unexpected condition has occurred on template ACL initialization

iosxe-acl

"show memory"

FMANRP_ACL-4-TMPLACLNOMEMERR

4-Warning

Template ACL no memory error

An unexpected condition has occurred on template ACL processing

iosxe-acl

"show memory"

FMANRP_ACL-4-TMPLACLDISABLEERR

4-Warning

Not enough resources to disable template ACL

Not enough resurces to store individual ACLs

iosxe-acl

"show ip access-list template summary"

FMANRP_ACL-3-EXPOGACLLIMITERR

3-Error

Expanded OGACL [chars] size [dec] exceeded MAX ACL limit [dec]

Expanded OGACL size exceeded the maximum ACL limit. Command rejected

iosxe-acl

"Reduce # of ACEs in the ACL"

FMANRP_IPSEC-6-HAPI_PCP_NACK

6-Information

[chars]: PCP NACK trans 0x[hec] opcode 0x[hec] errcode 0x[hec]: crypto

A failure has occured during security policy downloading in crypto hardware. The command is rejected.

iosxe-ipsec

"The configuration may be ignorable or recovered " "automatically in crypto hardware. The session may " "still be functional but less than optimal " "performance. If you determine that the system is " "adversely affected then Embedded Services Processor " "ESP tracelog should be collected. "

FMANRP_IPSEC-3-HAPI_PCP_UNEXP_REPLY

3-Error

[chars]: PCP trans 0x[hec] opcode 0x[hec]: unexpected reply from crypto

An unexpected internal software error. Engineering must be reported and investigate this occurrence.

iosxe-ipsec

LOG_STD_DDTS_TAC_DETAILS

IOSXE_FMANRP_CEF-3-NOFIB

3-Error

FIB entry is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB entry structure.

iosxe-fwdmgr

"show ip cef"

IOSXE_FMANRP_CEF-3-NOFIBSB

3-Error

FIB SB entry is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB SB entry structure.

iosxe-fwdmgr

"show ip cef"

IOSXE_FMANRP_CEF-3-NOFIBTABLE

3-Error

FIB table is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB table structure.

iosxe-fwdmgr

"show ip cef"

IOSXE_FMANRP_CEF-3-NOFIBIDB

3-Error

FIB interface is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure.

iosxe-fwdmgr

"show ip cef"

IOSXE_FMANRP_CEF-3-ENQUEFAIL

3-Error

Unable to send [chars] [chars] message to Forwarding Manager Process

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_CEF-4-UPDFRAGSTATSERR

4-Warning

Update IP Fragmentation statistics error

An unexpected condition has occurred when updating fragmentation \n\ statistics

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_CEF-4-UPDREASSSTATSERR

4-Warning

Update IP Reassembly statistics error

An unexpected condition has occurred when updating reassembly \n\ statistics

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_CEF-4-UPDSTATSERR

4-Warning

Update CEF statistics error

An unexpected condition has occurred when updating cef statistics

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_CEF-3-ROUTEMSGMARSHAL

3-Error

Failed to copy route essage to IPC buffer for prefix [chars]/[dec] - [chars]

This operation to build a TDL messages for route download has failed.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_CEF-3-NOFIBPUSHCNT

3-Error

FIB push counter is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB push counter structure.

iosxe-fwdmgr

"show ip cef"

IOSXE_FMANRP_CEF-3-NOFIBSIGNAL

3-Error

FIB signal is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB signal structure.

iosxe-fwdmgr

"show ip cef"

IOSXE_FMANRP_CEF-3-NONATADDR

3-Error

NAT address is null

An unexpected condition has occurred which is due to the absence of\n\ an NAT address.

iosxe-fwdmgr

"show ip alias"

FMANRP_PBR-3-RTMAPNULL

3-Error

The route-map structure for [chars] is NULL

An unexpected condition has occurred due to the absence of an internal route-map data structure.

iosxe-pbr

"show route-map"

FMANRP_PBR-3-RTMAP_NAME_NULL

3-Error

The route-map name for [chars] is NULL

An unexpected condition has occurred due to the absence of an internal route-map data structure.

iosxe-pbr

"show route-map"

FMANRP_PBR-3-INVALIDIF

3-Error

The interface specified for '[chars]' is not valid

An non-existent interface is specified for the policy based routing route-map operation specified in the message.

iosxe-pbr

"show interface"

FMANRP_PBR-3-UNSUPPORTED_RMAP

3-Error

Route-map [chars] has unsupported options for Policy-Based Routing. It has been removed from the interface if applied.

The route-map attached to an interface for policy routing contains an action that is not supported on this platform. This is a hardware limitation.

hardware

"Reconfigure the route-map. Use only 'permit' " "entries and 'set ip next-hop' action in the " "route-map."

FMANRP_PBR-3-UNSUPPORTED_RMAP_COMMAND

3-Error

This Policy-Based Routing command is not supported on this platform. Use the no form of this command to remove it from configurations

Policy-Based Routing is not supported on this platform

hardware

"Remove this command"

FMANRP_DPSS-3-DPSSFOIPCALLOC

3-Error

Failed to alloc IPC buffer for dpss feature object 0x[hec] config\n\ message

This operation to allocate IPC buffer for dpss feature object \n\ configuration has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSFOTDLMSGMARSHAL

3-Error

Failed to copy dpss feature object config message to IPC buffer for\n\ fo_hdl 0x[hec]

This operation to build a TDL message for dpss feature object \n\ configuration has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSFOIOSDENQUEUE

3-Error

Failed to enqueue dpss feature object 0x[hec] config message for transmission

This operation to enqueue an IPC message for sending has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSFOTDLCREATE

3-Error

Failed to create tdl msg for dpss feature object 0x[hec] config message

This operation to create an TDL message has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSFOTDLSET

3-Error

Failed to set tdl msg detail for dpss feature object 0x[hec] config message

This operation to set an TDL message has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSGLOBALTDLCREATE

3-Error

Failed to create tdl msg for dpss global config message

This operation to create an TDL message has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSGLOBALTDLSET

3-Error

Failed to set tdl msg detail for dpss global config message

This operation to set an TDL message has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSGLOBALIPCALLOC

3-Error

Failed to alloc IPC buffer for dpss global config\n\ message

This operation to allocate IPC buffer for dpss global \n\ configuration has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSGLOBALTDLMSGMARSHAL

3-Error

Failed to copy dpss global config message to IPC buffer

This operation to build a TDL message for dpss global \n\ configuration has failed.

asr1k-dpss

LOG_STD_ACTION

FMANRP_DPSS-3-DPSSGLOBALIOSDENQUEUE

3-Error

Failed to enqueue dpss global config message for transmission

This operation to enqueue an IPC message for sending has failed.

asr1k-dpss

LOG_STD_ACTION

IOSXE_MLP-3-ENQUEFAIL

3-Error

Unable to send [chars] [chars] message to Forwarding Manager Process

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_MLP-4-UPDSTATSERR

4-Warning

Update MLP statistics error

An unexpected condition has occurred when updating mlp statistics

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_MLP-2-DB_ENTRY_ALLOC_FAIL

2-Critical

MLP link db entry allocation for link [chars] failed

MLP link database error. Memory chunk allocation for MLP link database entry has failed.

iosxe-mlppp

"Check for accurate memory management. " "Perform memory leak checks and " "look for memory corruption causes. " "Execute 'show proc memory' command."

IOSXE_MLP-2-DB_INSERT_FAIL

2-Critical

MLP link db entry add for interface [chars] failed

MLP link database error. Insertion of a new entry into MLP link database has failed.

iosxe-mlppp

"Check for accurate memory management. " "Perform memory leak checks " "look for memory corruption causes " "verify correct database management. " "Execute 'show proc memory' command."

IOSXE_MLP-2-DB_DELETE_FAIL

2-Critical

MLP link db entry delete for link [chars] failed

MLP link database error. Removal of entry from MLP link database has failed.

iosxe-mlppp

"Check for accurate memory management. " "Perform memory leak checks " "look for mamory corruption causes and " "check for correct database management. " "Execute 'show proc memory' command. "

IOSXE_MLP-2-DB_ENTRY_FREE_FAIL

2-Critical

MLP link entry free failed

MLP link database error. Memory chunk free of MLP link database entry has failed.

iosxe-mlppp

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command."

IOSXE_MLP-2-DB_ALLOC_FAIL

2-Critical

MLP link db allocation failed

MLP link database error. Memory chunk creation for MLP link database has failed.

iosxe-mlppp

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command."

IOSXE_MLP-2-DB_DESTROY_FAIL

2-Critical

MLP link database destroy failed

MLP link database error. Memory chunk destroy has failed for MLP link database.

iosxe-mlppp

"Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute show proc memory command."

FMANRP_MFR-3-TDLFAIL

3-Error

Unable to send [chars] [chars] message to Forwarding Manager Process [chars]

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs.

iosxe-mlfr

LOG_STD_ACTION

FMANRP_MFR-3-BNDLFAIL

3-Error

Unable to [chars] bundle [chars]

An unexpected condition has occurred at Bundle configuration

iosxe-mlfr

LOG_STD_ACTION

FMANRP_MFR-3-BLFAIL

3-Error

Unable to [chars] link [chars] [chars]

An unexpected condition has occurred at Bundle link configuration [chars]

iosxe-mlfr

LOG_STD_ACTION

FMANRP_MFR-3-BLCFGFAIL

3-Error

Unable to [chars] link [chars] [chars]

An unexpected condition has occurred at Bundle link configuration [chars]

iosxe-mlfr

LOG_STD_ACTION

COND_DEBUG_HA-2-INIT

2-Critical

COND_DEBUG ISSU client initialization failed to [chars]. Error: [dec] [chars]

The COND_DEBUG ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

cond_debug

LOG_STD_ACTION

COND_DEBUG_HA-3-TRANSFORM

3-Error

COND_DEBUG ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The COND_DEBUG ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the COND_DEBUG state between the active device and the standby device is not identical.

cond_debug

"show issu session <client_id> and " "show issu negotiated version <session_id>"

COND_DEBUG_HA-3-MSG_SIZE

3-Error

COND_DEBUG ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The COND_DEBUG ISSU client failed to calculate the MTU for the specified message. The COND_DEBUG ISSU client will not able to send the message to the standby device.

cond_debug

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

COND_DEBUG_HA-3-INVALID_SESSION

3-Error

COND_DEBUG ISSU client does not have a valid registered session.

The COND_DEBUG ISSU client does not have a valid registered session.

cond_debug

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

COND_DEBUG_HA-2-SESSION_REGISTRY

2-Critical

COND_DEBUG ISSU client failed to register session information. Error: [dec] [chars]

The COND_DEBUG ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

cond_debug

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

COND_DEBUG_HA-3-SESSION_UNREGISTRY

3-Error

COND_DEBUG ISSU client failed to unregister session information. Error: [dec] [chars]

The COND_DEBUG ISSU client failed to unregister session information.

cond_debug

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

COND_DEBUG_HA-2-SESSION_NEGO

2-Critical

COND_DEBUG ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The COND_DEBUG ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

cond_debug

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

COND_DEBUG_HA-2-SEND_NEGO_FAILED

2-Critical

COND_DEBUG ISSU client failed to send negotiation message. Error: [dec] [chars]

The COND_DEBUG ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

cond_debug

"show logging and show checkpoint client"

COND_DEBUG_HA-2-GET_BUFFER

2-Critical

COND_DEBUG ISSU client failed to get buffer for message. Error: [dec] [chars]

The COND_DEBUG HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly.

cond_debug

"show logging and show checkpoint client"

IOSXE_FMANRP_IPHC-4-NOIDB

4-Warning

IOS interface [chars] is not available for an IP header compression

When receiving an IP header compression statistic update for an \n\ interface or sub-interface in IOS one of data structures in IOS\n\ to store those IP header compression statistics is NULL

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_IPHC-4-INVALIDSTATSTYPE

4-Warning

IP header compression statistic message received has invalid stats type

When receiving an IP header compression statistic update for an \n\ interface or sub-interface in IOS the statistic type in that \n\ message is invalid.

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_IPHC-4-STATSERR

4-Warning

There is error when processing IP header compression statistic message received on IOS

When receiving an IP header compression statistic update for an \n\ interface or sub-interface in IOS an unexpected error occurred

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_CCE-4-CCE_STACK_LIMIT

4-Warning

Failed to create class [dec] filter list

An operation to send a filter list to the forwarding \n\ processor for a particular class has failed due to a \n\ resource issue. This may imply that the notification was\n\ dropped.

iosxe-fwdmgr

"show class-map [type\n\ <class type> <name>]"

IOSXE_FMANRP_CCE-3-CCE_INVALID_FILTER_RELN

3-Error

Invalid filter relation [dec]

An internal error occured when trying to build class-map information for one of the classes in a policy-map.

iosxe-fwdmgr

"show policy-map \n\ [type <policy type> <name>]"

IOSXE_FMANRP_CCE-3-CCE_FILTER_OVERFLOW

3-Error

Filter list overflow at type [chars]

An internal error occured when trying to build class-map information for one of the classes in a policy-map.

iosxe-fwdmgr

"show class-map \n\ [type <class type> <name>]"

IOSXE_FMANRP_CCE-3-CCE_CLASS_CREATE

3-Error

Unable to create class [dec].[dec]

An error occured when trying to create a class-map.

iosxe-fwdmgr

"show policy-map\n\ [type <policy type> <name>]"

IOSXE_FMANRP_CCE-4-CCE_NESTED_CLASS_LIMIT

4-Warning

Nested class [dec] layers cannot exceed 4

When configure nested classes as match statements \n\ the total levels of nested classes cannot exceed 4 layers

iosxe-fwdmgr

"show class-map [type\n\ <class type> <name>]"

IOSXE_FMANRP_VPLS-3-INVALID_VALUE

3-Error

Invalid value for [chars]

An unexpected condition in which an invalid value is get during VPLS configuration.

iosxe-vpls

LOG_STD_ACTION

IOSXE_FMANRP_ADJ-3-NOADJ

3-Error

Adjacency entry is null

An unexpected condition has occurred which is due to the absence of\n\ an adjacency entry structure.

iosxe-fwdmgr

"show adjacency"

IOSXE_FMANRP_ADJ-3-NOFIBHWIDB

3-Error

FIB Interface [chars] is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure.

iosxe-fwdmgr

"show adj"

IOSXE_FMANRP_ADJ-3-ENQUEFAIL

3-Error

Unable to send [chars] [chars] message to Forwarding Manager Process

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_ADJ-3-ENCSIZE

3-Error

Invalid encap length [dec] which is larger than max allowed [dec] bytes

An unexpected condition has occurred which is due to invalid\n\ adjacency encapsulation size being larger than the maximum value\n\ allowed.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_MACSEC-3-INVALIDIF

3-Error

Configuration specified invalid value [dec] for [chars]

An non-existent interface is specified for MACSEC operation.

iosxe-macsec

"show interface"

IOSXE_FMANRP_MACSEC-3-IOSXE_FMANRP_MACSEC_STATS

3-Error

Invalid stats update. type [dec] id [dec]

An invalid stats update is received by MACSEC.

iosxe-macsec

"show platform software macsec"

IOSXE_FMANRP_MCAST-3-FMANRP_BADMAF

3-Error

Unknown Multicast AF [dec]

An unexpected condition has occurred due to the download\n\ of an unknown MFIB address family code.

iosxe-fwdmgr

"show mfib"

IOSXE_FMANRP_MCAST-3-FMANRP_DELID

3-Error

Failed to remove Multicast ID [dec]

An unexpected condition has occurred due to the failure\n\ to delete an internal identifier that is no longer in use.

iosxe-fwdmgr

"show mfib"

IOSXE_FMANRP_MCAST-3-FMANRP_NOID

3-Error

No Multicast ID for [inet] [inet]/[dec] action [inet]

-

iosxe-fwdmgr

"show ip mroute count"

IOSXE_FMANRP_MCAST-3-FMANRP_MSTATS

3-Error

Can't process multicast stats upload from fman. type [dec] id [dec]

An unexpected condition has occurred preventing interpretation\n\ of the stats message from the forwarding manager. This will\n\ prevent the statistics for the affected multicast entries from\n\ being updated.

iosxe-fwdmgr

"show ip mroute count"

IOSXE_FMANRP_MCAST-3-MCASTID

3-Error

Multicast ID management error

An unexpected condition has occurred causing an internal\n\ ID to not be properly handled or disposed of

iosxe-fwdmgr

"show ip mroute count"

IOSXE_FMANRP_MCAST-3-FMANRP_MCAP

3-Error

Multicast Capability [chars]:[chars] error [chars]

An unexpected condition has occurred due to the failure to set\n\ a multicast capability for this platform.

iosxe-fwdmgr

"show mfib state cap"

IOSXE_FMANRP_MCAST-3-FMANRP_UPDINTF

3-Error

Failed to update flag count for [chars] due to [chars]

An unexpected condition has occurred due to the failure\n\ to update the interface flag count

iosxe-fwdmgr

"show mfib"

FMANRP_NAT-4-NOSWIDB

4-Warning

Sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a swidb structure.

iosxe-nat

"show ip interface"

FMANRP_NAT-3-IFTDLMSGMARSHAL

3-Error

Failed to copy interface config essage to IPC buffer for \n\ Interface [chars] 0x[hec] domain [chars] operation [chars]

This operation to build a TDL message for interface configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NONATSERVICE

4-Warning

Service structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT service structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-3-SERTDLMSGMARSHAL

3-Error

Failed to copy service config message to IPC buffer for\n\ application type [dec] protocol type [dec] port [dec]

This operation to build a TDL message for service configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-SERVICERM

3-Error

Failed to delete NAT services for appl type [chars] protocol [chars]\n\ port [dec]

An unexpected condition has occurred which is due to the failure\n\ to remove data structures for NAT special services.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NOPOOL

4-Warning

Pool structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT pool structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-4-NOMAPPING

4-Warning

A mapping structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT mapping structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-4-BADACTION

4-Warning

Invalid action [dec] for NAT configuration

An unexpected condition has occurred which is invalid action \n\ for a NAT configuration.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-3-POOLTDLMSGMARSHAL

3-Error

Failed to copy pool config message to IPC buffer for\n\ pool [chars] id [dec]

This operation to build a TDL message for pool configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-MAPPINGTDLMSGMARSHAL

3-Error

Failed to copy mapping config message to IPC buffer for\n\ mapping id [dec] vrf table id [dec]

This operation to build a TDL message for mapping configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IFADDRTDLMSGMARSHAL

3-Error

Failed to copy interface address change message to IPC buffer for\n\ interface [chars] new address [inet]

This operation to build a TDL message for NAT interface address\n\ configuration has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-VRFDELTDLMSGMARSHAL

3-Error

Failed to copy VRF delete message to IPC buffer for vrf table id [dec]

This operation to build a TDL message for vrf deletion configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-TIMEOUTTDLMSGMARSHAL

3-Error

Failed to copy timeout config message to IPC buffer for\n\ timeout type [dec]

This operation to build a TDL message for timeout configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NORANGE

4-Warning

Pool address range structure is null

An unexpected condition has occurred which is due to the absence of\n\ a NAT pool address range structure.

iosxe-nat

LOG_STD_SH_CMD_ACTION

FMANRP_NAT-3-RANGETDLMSGMARSHAL

3-Error

Failed to copy pool address range config message to IPC buffer for\n\ pool [chars] range start [inet] range end [inet]

This operation to build a TDL message for address range configuration\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTTDLMSGMARSHAL

3-Error

Failed to copy portlist config message to IPC buffer for\n\ addr [inet] proto [dec] start_port [dec] end_port [dec]

This operation to build a TDL message for portlist add/delete\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NOACL

4-Warning

Access list is null

An unexpected condition has occurred which is due to the absence of\n\ an access list structure.

iosxe-nat

"show ip access-lists"

FMANRP_NAT-3-MAXENTRYTDLMSGMARSHAL

3-Error

Failed to copy max entry config message to IPC buffer for\n\ type [chars] entry data 0x[hec] max_limit [dec]

This operation to build a TDL message for max entry add/delete\n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-STATSUPDTDL

3-Error

Failed to update NAT [chars] statistics

An unexpected condition has occurred when updating statistics

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPALIASTDL

3-Error

Error with ipalias message received from data path

An unexpected condition has occurred with received ipalias \n\ message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPALIASTYPE

3-Error

Received ipalias message from data path with unsupported \n\ address type [dec]

An unexpected condition has occurred with received ipalias \n\ message from data path with unsupported address type

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPSTATICROUTETDL

3-Error

Error with static ip route message received from data path

An unexpected condition has occurred with received static\n\ ip route message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IPSTATICROUTETYPE

3-Error

Received ip static route message from data path with\n\ unsupported address type

An unexpected condition has occurred with received static \n\ ip route message from data path with unsupported address type

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTTDL

3-Error

Error with portlist allocation request message received from data path

An unexpected condition has occurred with received portlist\n\ allocation request message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTTYPE

3-Error

Address type [dec] for global address in the portlist allocation request is not supported

An unexpected address type has occurred with received portlist\n\ allocation request message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-PORTLISTPROTO

3-Error

Protocol type [dec] for global addr [inet] in the portlist allocation request is not supported

An unexpected protocol type has occurred with received portlist\n\ allocation request message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-DEBUGTDLMSGMARSHAL

3-Error

Failed to copy debug NAT request message to IPC buffer

This operation to build a TDL message for debug NAT command \n\ has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-IOSDENQUEUE

3-Error

Failed to enqueue NAT [chars] message for transmission

This operation to enqueue an IPC message for sending has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-AVLTREEWALK

3-Error

Failed to walk NAT [chars] database for [chars]

This operation to perform stale processing has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-AVLDELETE

3-Error

Failed to delete node from NAT [chars] database for [inet]

This operation to perform delete processing has failed.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-WLANSESSTDL

3-Error

Error with WLAN session message received from data path

An unexpected condition has occurred with received WLAN session \n\ message from data path

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-WLANSESSTYPE

3-Error

Received WLAN session message from data path with unsupported \n\ address type [dec]

An unexpected condition has occurred with received WLAN session \n\ message from data path with unsupported address type

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-WLANSESSIDB

3-Error

Received WLAN session message from data path with nil \n\ input interface for inside local host [inet]

An unexpected condition has occurred with received WLAN session \n\ message from data path with nil input interface

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-4-NOLOGGINGPARAM

4-Warning

Highspeed logging structure is nil

An unexpected condition has occurred which is due to the absence of\n\ a logging parameter structure.

iosxe-nat

"show running"

FMANRP_NAT-4-LOGGING_PARAM

4-Warning

Highspeed logging export [chars] [dec] unsupported

An unsupported exporting paremeter for highspeed logging\n\ on data path is received.

iosxe-nat

"show running"

FMANRP_NAT-4-NOREPLICATEPARAM

4-Warning

Session replication structure is nil

An unexpected condition has occurred which is due to the absence of\n\ a session replication parameter structure.

iosxe-nat

"show running"

FMANRP_NAT-3-MIBEVENT

3-Error

Failed to get NAT MIB response message: [chars]

An unsupported error occured with waiting for NAT MIB respsonse \n\ message.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-INVALID_ADDRESS

3-Error

Received an invalid address [inet]

An unsupported address for the given config was received.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-MSGALLOCERR

3-Error

Failed to allocate message

When attempting to send message to dataplane there was not enough memory to allocate the message.

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT-3-NATSETTDLMSGFAIL

3-Error

When download [chars] failed to set a field in message

sotware error.

iosxe-nat

LOG_STD_ACTION

IOSXE_CXSC-3-ALLOC

3-Error

Failed to allocate message for proposition

When attempting to program the dataplane with a CXSC proposition object there was no enough memory to allocate the message.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-MESSAGE

3-Error

Failed to send message for proposition

When the proposition was being prepared for sending to the data plane there was an error.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-ACTION

3-Error

Unknown proposition action [dec]

-

-

-

IOSXE_CXSC-3-BAD_PROPOSITION

3-Error

Proposition obj corrupt

When the proposition was being sent to the data plane the object itself is corrupt.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-BAD_SUMMARY

3-Error

Summary obj corrupt

When the proposition summary was being sent to the data plane the object itself is corrupt.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-4-DUAL_RP_UNSUPPORTED

4-Warning

Dual RPs are not supported in conjunction with CXSC

CXSC is not supported in a dual RP environment. To resolve this warning either unconfigure CXSC or remove the redundant Route Processor.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-RF_INIT

3-Error

Failed to initialize CXSC Redundancy Facility client

An unexpected condition occurred where the CXSC Redundancy Facility failed to initialize.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-STILE_ACTIVATE

3-Error

Failed to activate NBAR classification: [dec]

An unexpected condition occurred where the CXSC NBAR protocol classification failed to activate.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-STATISTICS_ALLOCATION

3-Error

Unable to allocate space for statistics

During initialization there was failure in the allocation of the memory to gather the statistics. It is non fatal but after seeing this message the CXSC subsystem will not be able to gather statistics.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-BAD_PROTOCOLPACK

3-Error

Invalid Protocol Pack object

When the Protocol Pack was being sent to the data plane the object's contents were invalid.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-FILESYSTEM_ERR

3-Error

FileSystem Error [chars]: Unable to Copy File from

Unable to copy the NBAR Protocol Pack File to the file system for subsequent loading. The system will revert to the previously loaded Protocol Pack.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-INSUFFICIENT_ALLOC_IOSXE_VER

3-Error

Insufficent memory allocated for IOSXE version String

The input IOSXE Version String has insufficient memory to hold the IOSXE Version.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-INSUFFICIENT_ALLOC_NBAR_VER

3-Error

Insufficent memory allocated for NBAR Engine Version String

The input NBAR Engine Version string has insufficient memory to hold the NBAR Engine Version.

iosxe-cxsc

LOG_STD_ACTION

IOSXE_CXSC-3-PLATFORM_TYPE

3-Error

Unrecognised platform type. CPU ID [dec]

The platform that the cxsc service is being installed on is not recognised. The most likely cause is that this platform is not supported.

iosxe-cxsc

LOG_STD_ACTION

FMANRP_MPLS-3-NOOBJ

3-Error

Object entry is null

An unexpected condition has occurred which is due to the absence of\n\ an object entry structure.

asr1k-fwdmgr

"show mpls"

FMANRP_MPLS-3-ENQUEFAIL

3-Error

Unable to send [chars] [chars] message to Forwarding Manager Process

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs.

asr1k-fwdmgr

LOG_STD_ACTION

FMANRP_MPLS-3-UNSPTYPE

3-Error

Not supported bundle type [dec]

An unexpected condition has occurred which is due to an operation request\n\ to an unsupported bundle oce type is received.

asr1k-fwdmgr

LOG_STD_ACTION

PLATFORM_SEC-2-NOIDB

2-Critical

Software module for [chars] received null SWIDB.

The security component received null SWIDB. This could be due to interfaces deleted by the time the function gets called. Please collect history of actions performed before hitting this error for further investigations.

accsw-security

LOG_STD_ACTION

PLATFORM_SEC-2-NOHWIDB

2-Critical

Software module for [chars] received null HWIDB.

The security component received null HWIDB. This could be due to IDB creation issue. Please collect history of actions performed before hitting this error for further investigations.

accsw-security

LOG_STD_ACTION

PLATFORM_SEC-6-SGACLHIT

6-Information

list [chars] [chars] [chars] [inet][dec] -> [inet][dec] SGT [dec] DGT [dec]

A packet matching the log criteria for the given sg access list was detected.

accsw-security

LOG_STD_NO_ACTION

IOSXE_FMANRP_L2FIB-3-INVALIDIF

3-Error

Configuration specified invalid value [dec] for [chars]

An non-existent interface is specified for L2FIB operation.

iosxe-l2fib

"show interface"

IOSXE_FMANRP_L2FIB-3-IOSXE_FMANRP_L2FIB_STATS

3-Error

Invalid stats update. type [dec] id [dec]

An invalid stats update is received by L2FIB.

iosxe-l2fib

"show platform software l2fib"

IOSXE_FMANRP_CCK-4-FMANRP_INCONSISTENT

4-Warning

Consistency Check for [chars] cannot be completed for all entries. Check 'show consistency-checker run-id [dec] detail'.

Unexpected counts of updates happened during the CCK Run.

iosxe-fwdmgr

"show consistency-checker run-id "

IOSXE_CIDB-3-ALLOC

3-Error

Failed to allocate message for CIDB message

When attempting to program the dataplane with a CIDB object there was not enough memory to allocate the message.

iosxe-cidb

LOG_STD_ACTION

IOSXE_CIDB-3-MESSAGE

3-Error

Failed to send message for CIDB object

When the cidb object was being prepared to be sent to the data plane there was an error.

iosxe-cidb

LOG_STD_ACTION

IOSXE_FMANRP_EOAM-3-IOSXE_FMANRP_EOAM_CONFIG

3-Error

MIP Filtering enable/disable will take into affect only if it is applied before applying any cfm config.

MIP filtering enable/disable should be applied before applying cfm config. Otherwise the command will have no affect on CFM Filtering.

asr1k-ecfm

"show platform software eoam fp active cfm global"

IOSXE_WCCP-4-NOINPUT

4-Warning

NULL input [chars]

An unexpected condition has occurred which is due to the NULL value\n\ of the input parameter.

asr1k-wccp

"show ip wccp"

IOSXE_WCCP-4-NOSVCGRP

4-Warning

[chars] Service Group [dec] [dec] [dec] NOT exist

An unexpected condition has occurred which is due to the absence of\n\ the service group structure.

asr1k-wccp

"show ip wccp"

IOSXE_WCCP-4-NOACL

4-Warning

Access list is null

An unexpected condition has occurred which is due to the absence of\n\ an access list structure.

asr1k-wccp

"show ip access-lists"

IOSXE_WCCP-4-ACELIMIT

4-Warning

Too many ACEs in MASK ACL please switch to Hash mode

Mask merged ACL generate too many ACEs.

asr1k-wccp

"show ip access-lists"

IOSXE_WCCP-4-BADACE

4-Warning

Access list contains invalid ace

An unexpected condition has occurred which is due to an invalid\n\ statement in the access list structure.

asr1k-wccp

"show ip access-lists"

IOSXE_WCCP-4-NOINTF

4-Warning

No [chars] interface info for Service Group [dec] [dec] [dec]

An unexpected condition has occurred which is due to the absence of\n\ MCP WCCP interface info for the specific service group.

asr1k-wccp

"show platform software wccp"

IOSXE_WCCP-4-UNKNOWNDIR

4-Warning

Unknown [chars] interface direction 0x[hec] for Service Group [dec] [dec] [dec]

An unexpected condition has occurred which is due to the unknown direction\n\ has been applied to the interface for the service group.

asr1k-wccp

"show platform software wccp"

IOSXE_WCCP-4-NOSTATS

4-Warning

WCCP [chars] message error

An unexpected condition has occurred which is due to the error in \n\ receiving WCCP stats update message.

asr1k-wccp

"show platform software wccp <id> counters"

IOSXE_WCCP-4-NOSTATSSVC

4-Warning

Service Group [dec] [dec] [dec] not exist for the stats message

An unexpected condition has occurred which can't find the service group\n\ for the service group stats message.

asr1k-wccp

"show platform software wccp"

IOSXE_WCCP-4-NOSTATSINTF

4-Warning

Interface handle [dec] not exsit for the stats message

An unexpected condition has occurred which can't find the interface handle\n\ for the interface stats message.

asr1k-wccp

"show platform software wccp <id> int counters"

FMANRP_SC-3-SCTXTDLMSGMARSHAL

3-Error

Failed to copy service context config message to IPC buffer for\n\ sctx_name id [dec]

This operation to build a TDL message for service context \n\ configuration has failed.

iosxe-service_controller

LOG_STD_ACTION

FMANRP_SC-3-DBGTDLMSGMARSHAL

3-Error

Failed to copy debug SC request message to IPC buffer

This operation to build a TDL message for debug SC command \n\ has failed.

iosxe-service_controller

LOG_STD_ACTION

FMANRP_SC-3-SCIOSDENQUEUE

3-Error

Failed to enqueue SC [chars] message for transmission

This operation to enqueue an IPC message for sending has failed.

iosxe-service_controller

LOG_STD_ACTION

FMANRP_SC-3-INTFTDLMSGMARSHAL

3-Error

Failed to copy interface config message to IPC buffer for \n\ Interface [chars] 0x[hec] operation [chars]

This operation to build a TDL message for interface configuration\n\ has failed.

iosxe-service_controller

LOG_STD_ACTION

FMANRP_SC-4-SCNOSWIDB

4-Warning

Sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a swidb structure.

iosxe-service_controller

"show ip interface"

FMANRP_SC-4-NOSERVICECTX

4-Warning

A mapping structure is null

An unexpected condition has occurred which is due to the absence of\n\ a SC mapping structure.

iosxe-service_controller

LOG_STD_SH_CMD_ACTION

FMANRP_SC-4-SCBADACTION

4-Warning

Invalid action [dec] for SC configuration

An unexpected condition has occurred which is invalid action \n\ for a SC configuration.

iosxe-service_controller

LOG_STD_SH_CMD_ACTION

FMANRP_NAT66-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT66-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

iosxe-nat

LOG_STD_ACTION

IOSXE_FMANRP_LISP_SFLTR-3-UPDTABLESTATSERR

3-Error

Update LISP-SFLTR Table statistics error

An unexpected condition has occurred when updating lisp-sfltr table statistics

asr1k-lisp

LOG_STD_ACTION

IOSXE_FMANRP_LISP_SFLTR-3-UPDENTRYSTATSERR

3-Error

Update LISP-SFLTR Entry statistics error

An unexpected condition has occurred when updating lisp-sfltr entry statistics

asr1k-lisp

LOG_STD_ACTION

IOSXE_FMANRP_RTMAP-3-RTMAPNULL

3-Error

The route-map structure for [chars] is null

An unexpected condition has occurred which is due to the absence of\n\ a route-map data structure.

iosxe-fwdmgr

"show route-map"

IOSXE_FMANRP_RTMAP-4-UNKOWNCLIANT

4-Warning

Unknown client type [dec] received

An unexpected known client type is received for route-map download.

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_RTMAP-3-INVALID_LIST

3-Error

NULL

An internal list structure has been detected as invalid.

iosxe-pbr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_RTMAP-3-RTMAP_UNSUPPORTED

3-Error

Routemap [chars] contain unsupported match/set clause ignored

-

-

-

IFM_SHIM-3-AVL_TREE

3-Error

AVL tree [chars] action failed for [chars] iif-id 0x%016llx

AVL tree operation failure for specific interface object in IFM-SHIM software module. This usually implies a duplicate node already existing or the tree data structure corruption.

accsw-platform

LOG_STD_SH_TECH_ACTION

IFM_SHIM-3-SPI_FAILURE

3-Error

[chars]

IFM-SHIM is experiencing SPI failure.

accsw-platform

LOG_STD_SH_TECH_ACTION

IFM_SHIM-3-MALLOC_FAILURE

3-Error

Memory allocation failure when [chars]

Failed to allocated memory for a structure or event.

accsw-platform

LOG_STD_SH_TECH_ACTION

IFM_SHIM-3-SEND_FAILURE

3-Error

[chars]

IFM-SHIM is experiencing message send failure.

accsw-platform

LOG_STD_SH_TECH_ACTION

IFM_SHIM-3-INIT_FAILURE

3-Error

[chars]

IFM-SHIM has experienced initialization failure.

accsw-platform

LOG_STD_SH_TECH_ACTION

IFM_SHIM-3-INTIF_CREATE_FAILURE

3-Error

[chars]

Internal interface not created

accsw-platform

LOG_STD_SH_TECH_ACTION

IOSXE_FMANRP-4-MSGDISPATCHNULL

4-Warning

TDL messages NULL from IOS.

An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGDISPATCH

4-Warning

Unable to dispatch received TDL message '[chars]' from Forwarding Manager. LUID: [chars]

An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGIPCERR

4-Warning

Unable to process received IPC messages from Forwarding Manager\n\ error: [chars].

An unexpected condition has occurred while IOS trying to process\n\ received IPC message from Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-3-EPOCHTDLMSGMARSHAL

3-Error

Failed to copy epoch TDL message to IPC buffer epoch number [dec]

This operation to build a TDL messages for epoch message has failed.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-3-MSGMARSHALERR

3-Error

Unable to copy IPC messages into transport buffer. Message: [chars]

An unexpected condition has occurred while IOS trying to copy \n\ IPC message to transport buffer in order to send the message\n\ from IOSd to Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-3-MSGENQERR

3-Error

Unable to enqueue IPC messages to IOS IPC queue. Message: [chars].

An unexpected condition has occurred while IOS trying to enqueue \n\ IPC message to IOS IPC queue in order to send the message to\n\ Forwarding Manager.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP-4-MSGNONTDLSTATSERR

4-Warning

Unable to process received non-TDL stats message from \ Forwarding Manager\n\ error: [chars] [dec].

-

-

-

IOSXE_FMANRP_URPF-4-NOV4SWIDB

4-Warning

v4 sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a v4 swidb structure.

iosxe-fwdmgr

"show ip interface"

IOSXE_FMANRP_URPF-4-NOV6SWIDB

4-Warning

v6 sub-interface is null

An unexpected condition has occurred which is due to the absence of\n\ a v6 swidb structure.

iosxe-fwdmgr

"show ipv6 interface"

IOSXE_FMANRP_URPF-3-INVALIDIFHDL

3-Error

Invalid interface handle [dec] for interface number= [dec] swidb= [hex] name= [chars]

An unexpected condition has occurred which is due to an invalid \n\ interface handle

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_URPF-4-UPDV4STATSERR

4-Warning

Update v4 URPF statistics error

An unexpected condition has occurred when updating v4 URPF statistics

iosxe-fwdmgr

"show ip interface <name>"

IOSXE_FMANRP_URPF-4-UPDV6STATSERR

4-Warning

Update v6 URPF statistics error

An unexpected condition has occurred when updating v6 URPF statistics

iosxe-fwdmgr

"show ipv6 interface <name>"

IOSXE_FMANRP_FPM-4-INVALIDLENTYPE

4-Warning

Field length type in PHDF file is invalid

An unexpected condition has occurred which is due to the invalid\n\ field length type in PHDF file.

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_FPM-4-INVALIDMATCHTYPE

4-Warning

FPM match type is invalid [dec]

An unexpected condition has occurred which is due to the invalid\n\ FPM match type in one of FPM class-map filter match entry

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_FPM-4-INVALIDACTION

4-Warning

FPM feature action is invalid [dec]

An unexpected condition has occurred which is due to the invalid\n\ action type when trying to bind FPM action with target class group.

iosxe-fwdmgr

LOG_STD_SH_CMD_ACTION

IOSXE_FMANRP_FPM-3-NOSTATUPDATE

3-Error

Failed to update class-map statistics during periodic update

A statistics update for a class-map has failed.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_OBJID-5-DUPCREATE

5-Notice

Duplicate forwarding object creation obj_handle 0x[hec] type [dec] existing obj_id 0x[hec] type [dec]

An unexpected condition has occurred which results in duplicate\n\ forwarding object creation.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_OBJID2-3-DUPCREATE

3-Error

Duplicate forwarding object creation obj_handle 0x[hec] type [dec] existing obj_id 0x[hec] type [dec]

An unexpected condition has occurred which results in duplicate\n\ forwarding object creation with different object types.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_FMANRP_ETHER_DPLB-3-INVALIDIF

3-Error

Configuration specified invalid value [dec] for [chars]

An non-existent interface is specified for ETHER_DPLB operation.

iosxe-ether-dplb

"show interface"

IOSXE_FMANRP_ETHER_DPLB-3-IOSXE_FMANRP_ETHER_DPLB_STATS

3-Error

Invalid stats update. type [dec] id [dec]

An invalid stats update is received by ETHER_DPLB.

iosxe-ether-dplb

"show platform software ether_dplb"

FMANRP_QOS-3-ACTNOCLASSMAP

3-Error

Class-map information not found

An unexpected condition has occured when trying to determine class-map information for one of the classes in a policy-map.

asr1k-qos

"show policy-map"

FMANRP_QOS-3-ACTNOPOLICYMAP

3-Error

Policy-map information not found

An unexpected condition has occured when trying to determine policy-map information for one of the service policies attached to an interface.

asr1k-qos

"show policy-map"

FMANRP_QOS-3-QOSTDLMARSHAL

3-Error

Failed to copy more than [dec] bytes of message [chars] length [dec] into IPC buffer

An internal error occured when trying to build an IPC message.

asr1k-qos

LOG_STD_ACTION

FMANRP_QOS-3-QOSAPIPARAM

3-Error

Internal QOS API error.

An internal API error occured. QOS configuration may be limited.

asr1k-qos

LOG_STD_SH_TECH_ACTION

FMANRP_QOS-3-QOSIDBSP

3-Error

Service policy [[chars]] installation error: invalid interface type [dec]

An invalid interface type was encountered when trying to configure a service policy. This service policy could not be installed.

asr1k-qos

"show policy-map"

FMANRP_QOS-3-QOSGIDBSP

3-Error

Service policy [[chars]] installation error: invalid interface type [dec]

An invalid interface type was encountered when trying to configure a service policy. This service policy could not be installed.

asr1k-qos

"show policy-map"

FMANRP_QOS-4-QOSSTACK

4-Warning

Failed to install all classes for policymap [chars] excessive stack usage

An operation to configure the classes within a policymap \n\ has failed due to a resource issue. QoS configuration\n\ for this policymap is unlikely to work.

asr1k-qos

"show policy-map"

FMANRP_QOS-3-QOSCLASSDEL

3-Error

Error trying to remove class [chars] from policymap [chars]

An operation to remove a class from a policy \n\ has failed due to an internal error.

asr1k-qos

"show policy-map"

FMANRP_QOS-6-QOSCLASSEXIST

6-Information

class [chars] id [dec] in policymap [chars] id [dec] already exists

This is an informational message and no action \n\ is required.

asr1k-qos

"show policy-map"

FMANRP_QOS-3-NOPOLICERSTATS

3-Error

policer stats entry not found for class [dec].[dec] target [dec]

An internal error occured when looking up policer\n\ statistics.

asr1k-qos

"show policy-map interface"

FMANRP_QOS-3-NOACCOUNTSTATS

3-Error

account stats entry not found for class [dec].[dec] target [dec]

An internal error occured when looking up account\n\ statistics.

asr1k-qos

"show policy-map interface"

FMANRP_QOS-3-NOSETSTATS

3-Error

set stats entry not found for class [dec].[dec] target [dec]

An internal error occured when looking up set\n\ statistics.

asr1k-qos

"show policy-map interface"

FMANRP_QOS-4-QIDGENFAIL

4-Warning

qid generation failed reverting to default

An internal error occured during platform qos \n\ initialization.

asr1k-qos

LOG_STD_ACTION

FMANRP_QOS-4-QOSUBR

4-Warning

qos can not be attached to the target with UBR configured

An error occured to attach qos to ATM VC/VP\n\ target with UBR configured

asr1k-qos

LOG_STD_ACTION

FMANRP_QOS-4-NOFAIRQONVC

4-Warning

fair-queue can not be configured on the parent queue of an ATM VC use child queue instead

Configuring fair-queue on the parent queue of an ATM VC is not supported

asr1k-qos

LOG_STD_ACTION

FMANRP_QOS-4-CLMODIFYFAIL

4-Warning

classmap [chars] is currently used by policymap please remove policymap from all targets before the modification

An internal error occured when classmap being modified

asr1k-qos

LOG_STD_ACTION

FMANRP_QOS-3-CLPOLFAIL

3-Error

No support for client policy with policing in class-default and marking in custom class

An internal error occured during installing qos policy.

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-4-MPOLDMVPNGRE

4-Warning

Only Shape and/or BRR is allowed on the QoS policy on GRE tunnel on MPoL hierarchy

An error occurred during MPoL check between DMVPN and GRE tunnel QoS policy

asr1k-qos

LOG_STD_ACTION

FMANRP_QOS-3-QOSTMPLCREATEFAIL

3-Error

QoS template interface creation failed for policy [chars]: [chars]

An error occured during template interface creation

ewlc-qos

LOG_STD_ACTION

FMANRP_QOS-3-QOSTMPLDELETEFAIL

3-Error

QoS template interface deletion failed for policy [chars]: [chars]

An error occured during template interface deletion

ewlc-qos

LOG_STD_ACTION

FMANRP_QOS-3-QOSTMPLNONEXIST

3-Error

QoS template does not exist in [chars] for policymap [chars]

QoS template information does not exist

ewlc-qos

LOG_STD_ACTION

FMANRP_QOS-3-QOSTMPLDBERROR

3-Error

Failed to [chars] record for policymap [chars] err [chars]

Database operation failed for record of the policymap

ewlc-qos

LOG_STD_ACTION

FMANRP_QOS-3-QOSTMPLINUSE

3-Error

[chars]: [chars]

record of the policymap is already in use

ewlc-qos

LOG_STD_ACTION

FMANRP_QOS-3-PRILEVELSUPPORT

3-Error

Priority with level 3 is not supported.\n\ Service-policy : [chars]

Priority level 3 support is only for AVB policy.\n\ Hence configuration is rejected.

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-MARKDOWNCHECK

3-Error

Only markdown with a table-map is supported.

Error occured while performing exceed\n\ action check on the policy attached

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-CONFACTCHECK

3-Error

Conform-action in a policer can only be transmit.\n\ Policy Rejected.

Error occured while performing conform action\n\ check on the policer.

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-SHAPEBWSUPPORT

3-Error

Shape and bandwidth in the same class is unsupported.\n\ Policy Rejected. Service-policy : [chars]

Error occured while performing qos policy check.

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-QBUFFERSCHECK

3-Error

Sum of configured qbuffer ratios should be less than 100.\n\ Configuration not accepted. Service-policy : [chars]\n\ Info : classes for which qbuffer ratio is not configured\n\ is given a buffer ratio 1

Error occured while performing queue buffers\n\ policy install check. Wrong configuration

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-HWIDBCHECK

3-Error

Configuring service-policy on interface [chars] is not allowed

Error occured while attaching policy on gigethernet0/0.

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-HIERPOLICYCHECK

3-Error

Hierarchical Policy must have child under all user defined\n\ classes for wired ports. Service-policy : [chars]

Error occured while attaching a hierarchical policy

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-3-CHILDPOLICYCHECK

3-Error

Only 2 level policy is supported.\n\ Service-policy : [chars]

Error occured while attaching a hierarchical policy

polaris-qos

LOG_STD_ACTION

FMANRP_QOS-4-COPPMODIFY

4-Warning

Police rate modification for COPP system class [chars] is discouraged.

User modified police rate for COPP system classes.

accsw-p-qos

LOG_STD_ACTION

FMANRP_QOS-4-COPPREMOVE

4-Warning

Police rate removal for COPP system class [chars] is discouraged.

User removed police rate for COPP system classes.

accsw-p-qos

LOG_STD_ACTION

FMANRP_QOS-4-COPPMODRANGE

4-Warning

Police rate modification for COPP system class [chars] is out-of-range.

User modified police rate for COPP system classes.

accsw-p-qos

LOG_STD_ACTION

FMANRP_QOS-4-STACKBUFFER

4-Warning

Stack-buffer configuration has been modified. Current setting is stack-buffer [chars]. This change will take an effect once the configuration is written in flash write memory and then reload the switch.

Stack-buffer configurations in Catalyst 9300D switches.

accsw-p-qos

LOG_STD_ACTION

FMANRP_QOS-7-QOSPROFILE

7-Debug

The QoS profile has been modified to [chars]. The QoS policy-map's counters may not be updated accurately during the modification.

QoS profile configurations in CAT9K switches.

accsw-p-qos

LOG_STD_ACTION

FMANRP_QOS-7-QOSEVPNPOLICYCHECK

7-Debug

Unsupported QoS policy format in policy: [chars]

QoS policy validation check for EVPN policy

accsw-p-qos

LOG_STD_ACTION

IOSXE_MMA-3-ENQUEFAIL

3-Error

Enqueue of TDL message failed [chars].

-

-

-

IOSXE_FMANRP_ZONES-3-NOSTATUPDATE

3-Error

Failed to update zone-pair statistics during periodic update \n\ zone [chars] class [dec]

A statistics update for a zone-pair has failed.

iosxe-fwdmgr

LOG_STD_ACTION

ECFM_HSBY-5-FAILOVER

5-Notice

Failover from [chars] to [chars] in link protection group [dec].

The active outdoor unit ODU in the link protection group either has sent a message to the indoor unit IDU

uea-eoam

LOG_STD_NO_ACTION

ECFM_HSBY-5-KO

5-Notice

Remote ODU for link protection group [dec] on [chars] has indicated a failure

The remote outdoor unit ODU has raised its Sender KO flag indicating a failure.

uea-eoam

LOG_STD_NO_ACTION

ECFM_HSBY-5-FAIL

5-Notice

Communication lost with remote ODU for link protection group [dec] on [chars]

Communication was lost with the remote outdoor unit ODU due to either a CC message timeout or the interface going down.

uea-eoam

LOG_STD_NO_ACTION

ECFM_HSBY-5-OK

5-Notice

Remote ODU for link protection group [dec] on [chars] is now ok.

The previously failed remote outdoor unit ODU has recovered.

uea-eoam

LOG_STD_NO_ACTION

ECFM_HSBY-5-SUSPEND

5-Notice

Remote ODU for link protection group [dec] on [chars] is now suspended.

The remote outdoor unit ODU has requested monitoring of CC messages be temporarily suspended.

uea-eoam

LOG_STD_NO_ACTION

ECFM_HSBY-5-PORT_ACTIVE

5-Notice

[chars] link protection group [dec] now forwarding traffic

The remote outdoor unit ODU connected to this interface is now active. This interface is now forwarding traffic to/from the remote ODU.

uea-eoam

LOG_STD_NO_ACTION

IOSXE_FMANRP_EFP-3-INVALID_VALUE

3-Error

Configuration specified invalid value [dec] for [chars]

An unexpected condition in which configuration has accepted an invalid value.

asr1k-evc

LOG_STD_ACTION

IOSXE_FMANRP_EFP-3-EFP_ACCOUNTING_ERROR

3-Error

[chars] FMAN EFP support has encounterd an EFP accounting error on [chars]: [chars]

An inavlid EFP count found during EFP accouting in IOSXE FMAN EFP support.

asr1k-evc

show ethernet service instance detail

IOSXE_FMANRP_EFP-3-EFP_CFM_ERROR

3-Error

IOSXE FMAN EFP has encounterd an unsupported encap for CFM. Please remove any CFM configuration befor applying this encap.

The encapuslation type is not supported for CFM on IOSXE.

asr1k-ecfm

"Remove any CFM config and reapply encapusation"

IOSXE_FMANRP_EFP-3-EFP_AVL_DELETE

3-Error

Failed to delete EFP node with id [dec] in [chars]

An unexpected condition during configuration change

asr1k-evc

LOG_STD_ACTION

FMANRP_NAT64-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

iosxe-nat

LOG_STD_ACTION

FMANRP_NAT64-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

iosxe-nat

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-IDXBADRANGE

3-Error

Datapath IDB index [dec] is not in a valid range

An unexpected condition has occurred as the index of\n\ a datapath IDB is not valid.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDXALLOCFAILED

3-Error

Datapath IDB index allocation failed: [chars]

An unexpected condition has occurred as all the available of\n\ datapath IDB indices are used.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDXINSERTFAILED

3-Error

Insertion of datapath IDB index [dec] into database failed

An unexpected condition has occurred that insertion of\n\ datapath IDB indices failed.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDXLOOKUPFAILED

3-Error

Lookup of datapath IDB index from the database failed [chars]

An unexpected condition has occurred that lookup of\n\ datapath IDB indices failed.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDXDELETIONFAILED

3-Error

Deletion of datapath IDB index from the database failed \n\ [chars] - 0x[hec] rc [dec]

An unexpected condition has occurred that deletion of\n\ datapath IDB indices failed.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-NOHWSUBBLOCK

3-Error

HWIDB [chars] does not have a hardware subblock

An unexpected condition has occurred that no hardware subblock\n\ was previously allocated for a HWIDB.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-NOSWSUBBLOCK

3-Error

SWIDB [chars] does not have a software subblock

An unexpected condition has occurred that no software subblock\n\ was previously allocated for a SWIDB.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDBBADTYPE

3-Error

Datapath IDB type [dec] is not valid

An unexpected condition has occurred as the type of\n\ a datapath IDB is not valid.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDBEXIST

3-Error

Datapath IDB already exists in this mapping entry: [chars]-[dec]

An unexpected condition has occurred that an attempt is made\n\ to save datapath IDB in a mapping entry filled by another.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-IDBNONEXIST

3-Error

Datapath IDB does not exist in this mapping entry: [chars]-[dec]

Datapath IDB lookup points to empty mapping entry.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-RF

3-Error

Datapath IDB RF operation failed - [chars]

Failure in some datapath ID RF activity.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-CF

3-Error

Datapath IDB CF operation failed - [chars]

Failure in some datapath ID CF activity.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-RPC

3-Error

Datapath IDB RPC operation failed - [chars]

An operation pertaining to the ISSU support for DPIDX failed to complete\n\ using either the CF or IPC transport context with the reason\n\ specified

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-TRANSFORM

3-Error

[chars] of [chars] via [chars] failed for dpidx [dec]

An attempt to either encode or decode a versioned synchronization\n\ message has failed due to an internal error encountered by the ISSU\n\ component.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-RECEIVE

3-Error

Message via [chars] is [chars]

The ISSU negotiation with the peer failed to start for either the CF or\n\ IPC transport with the reason specified.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-6-READY

6-Information

[chars] peer not ready discarding [chars]

The synchronization attempt for the message has determined that the\n\ transport has lost communication with its peer. This is a normal\n\ situation which indicates that the standby route-processor is currently\n\ out of service implying a simplex redundancy mode.

-

-

IOSXE_RP_DPIDB-6-RELOAD

6-Information

[chars] reloading [chars]

A synchronization attempt between the active and standby RP peers has\n\ failed with the reason indicated. The standby peer is reloaded in an\n\ attempt to resynchronize when operating in a stateful redundant\n\ mode.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-DECODE

3-Error

Decode via [chars] of [chars] failed

The active route processor has sent a notification to the standby\n\ to inform of the completion of the bulk synchronization of the DPIDX\n\ configuration. The standby has failed to respond to the active\n\ informing that it received the notification noting the reason for\n\ the failure. The resultant action taken by the standby route\n\ processor is an attempt to resynchronize.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-BULK_SYNC

3-Error

Failed to send [chars] information to peer

-

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-DYN_SYNC

3-Error

Failed to process [chars] dynamic state

The incremental synchronization of the DPIDX configuration to the\n\ standby RP has failed to complete successfully. This implies that the\n\ configuration state between the active and standby RP is\n\ inconsistent.

iosxe-infmgr

"show interfaces"

IOSXE_RP_DPIDB-6-TIMEOUT

6-Information

Bulk sync is flow controlled by [chars]

The bulk synchronization of the DPIDX configuration to the standby RP\n\ has encountered a flow control condition which has effected a timeout\n\ awaiting the condition to clear. This will result in a reload of the\n\ standby RP to allow the bulk synchronization to restart.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-IDBNOTVAI

3-Error

Invalid API call for [chars]

Failure in an internal API

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-NULLTIMER

3-Error

NULL timer

A timer is NULL

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-LIST

3-Error

List [chars] failed for [chars]

List enqueue or removal failed

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-FASTNOTIFY

3-Error

Fast notify failed for [chars]

A fast notify message failed

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-DOWNLOADFAIL

3-Error

Unable to download [chars] message to [chars]

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the reported process.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-FRRLDFLOWIDDELETIONFAILED

3-Error

Deletion of fast-reroute flow ID with manager failed

An unexpected condition has occurred that deletion of\n\ fast-reroute flow ID.

iosxe-infmgr

"show interface"

IOSXE_RP_DPIDB-3-EFPSTATSFAILED

3-Error

EFP stats message data get error: [dec] for EFP [dec] on [chars]

An unexpected error occurred extracting fields from an EFP stats\n\ message.

iosxe-infmgr

LOG_STD_ACTION

IOSXE_RP_DPIDB-3-MTU_ALLOC_FAIL

3-Error

No hardware resources for [dec] byte MTU on [chars]

We reached to the threshold of maximum supported unique MTU on \ this platform.

-

LOG_STD_NO_ACTION

IOSXE_RP_DPIDB-3-IP_MTU_ALLOC_FAIL

3-Error

No hardware resources for [dec] byte IP MTU on [chars]

We reached to the threshold of maximum supported unique IP MTU \ on this platform.

-

LOG_STD_NO_ACTION

CLI_AGENT-3-TDL_GET

3-Error

Error [dec] handling TDL GET API from TDL message [[chars]]: [chars]

An unexpected condition has occurred while IOS is processing a TDL message received from the cli-agent

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-MSG_DISPATCH

3-Error

IOS cli-agent client message dispatcher error: [chars]

cli-agent RP message dispacher error

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-TDL_CREATE

3-Error

Error Creating TDL message '[chars]'

Could not create TDL message structure

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-MARSHAL

3-Error

Error [dec] marshaling TDL message [[chars]] buffer length [dec]: [chars]

An unexpected condition has occurred while IOS is marshaling TDL message to send to the cli-agent

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_ENQUEUE

3-Error

Unable to enqueue received message for processing [[chars]] : [chars]

Enqueue failed due multiple reason no context found TDL get error or run out of memory

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_MEM

3-Error

Memory Error: [chars]

Memory related problem

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-LOAD_FILE

3-Error

Unable to load file: [chars]

Unable to load data required by external configuration command set

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-FILE_OPEN

3-Error

Failed to open [chars]: [chars]

Failed to load external configuration command set

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_MODE

3-Error

Submode Error [chars]: [chars]

Unable to enter submode due to mode variable error

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_CTX

3-Error

Unable to get [chars] for [chars]

Unable to get message from the queue message received from cli-agent. There might be memory issue in IOSD.

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_DECODER

3-Error

Decoder error: [chars].

Error in decoder ring string which is generated by ECI metadata file. ECI metadata files are generated from sdl file using sdl compiler in WCM.

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_TIMEOUT

3-Error

Maximum timeout has been reached while waiting for cli-agent to respond: [dec] seconds

CLI Agent did not reply to IOS within expected timeout

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-ECI_INVALID_CTX

3-Error

Invalid message cannot be processed ctx: %#X

IOS recieved a message with invalid context ID. ECI cannot find the coresponding context from the table

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-4-ECI_IGNORE_MSG

4-Warning

Ignoring [chars] message: [chars]

ECI in pull state and ignores the incoming mesage from cli_agent

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-4-ECI_MSG_BLK_LOW

4-Warning

Not enough msg block for requesting message free msg block = [dec]

ECI have runout the message block to ask for more resp msg

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-4-ECI_UNKNOWN_EVENT

4-Warning

ECI recieved unknown event [dec]

ECI got unknown event

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-7-ECI_DEBUG

7-Debug

ECI: [chars][dec]

ECI module debug

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-BIPC_INIT

3-Error

Unable initialize BIPC connection to cli-agent

BIPC initialization failed BIPC infra is not available

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-BUILD_MSG

3-Error

Error [dec] building TDL message '[chars]' to send to the cli-agent: [chars]

An unexpected condition has occurred while IOS is building a TDL message to send to the cli-agent

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-BIPC_ENQUEUE

3-Error

Error [dec] queueing TDL message '[chars]' to send to the Shell Manager

An unexpected condition has occurred when IOS attempted to queue a TDL message to send to the Shell Manager

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-BIPC_BUFFER

3-Error

Error [dec] Unable to acquire a BIPC buffer for [chars] messages.

A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed.

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-BIPC_REMOTE

3-Error

BIPC connection is down while waiting for cli-agent to reply: [chars]

Connection to cli-agent is not available IOS

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-BIPC_CONN

3-Error

BIPC connection is down unable to send command: [chars]

IOS cli-agent client could not connect to cli-agent using BIPC

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-NOT_EOK

3-Error

Error [dec] in [chars]: [chars]

The error code passed in is not EOK

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-1-NVGEN_ERR

1-Alert

Error while processing NVGEN command: [chars]

An error occurred during an NVGEN command

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-1-NVGEN_TRACEBACK

1-Alert

Traceback: [chars]

Traceback from NVGEN command

polaris-mgbl-infra

LOG_STD_ACTION

CLI_AGENT-3-NVGEN_CMD_LIMIT

3-Error

NVGEN error: rendered command too long - truncated '[chars]'

Rendered command is too long and is truncated during NVGEN

polaris-mgbl-infra

LOG_STD_ACTION

MACSEC-4-RX_SC_EXCEED

4-Warning

RX SCI %llx : TX SCI %llx : vport [dec] : secy vport [dec]\n

Multiple In Late Packets Received.

-

"No action required normal operation."

MACSEC-4-TX_SC_EXCEED

4-Warning

TX SCI %llx : vport [dec]\n

TX SC exceeds hardware limit.

-

"No action required normal operation."

MACSEC-4-IPMTU_OVERSIZE

4-Warning

MACsec enabled interface [chars] IP MTU can't be more than [dec]

User config IP MTU size over MACsec enabled interface allows.

-

"Reconfigure IP MTU base on the suggested range."

MACSEC-5-TX_SA_PN_EXPIRE

5-Notice

TX SCI %llx : AN [dec] TX SA PN about to expire.\n

TX SA PN about to expire. Send a request to MKA to perform a SAK Rekey for the given TX SCI and AN.

-

"No action required normal operation."

MACSEC-6-CREATE_TX_SC

6-Information

[chars] TX SCI %llx : vport [dec]\n

MKA request MACsec PD to create a TX SC on the given TX SCI and vport.

-

"No action required normal operation."

MACSEC-6-DEL_TX_SC

6-Information

[chars] TX SCI %llx : vport [dec]\n

MKA request MACsec PD to delete a TX SC on the given TX SCI and vport.

-

"No action required normal operation."

MACSEC-6-CREATE_RX_SC

6-Information

[chars] RX SCI %llx : TX SCI %llx : vport [dec] : secy vport [dec]\n

MKA request MACsec PD to create a RX SC on the given RX SCI and vport.

-

"No action required normal operation."

MACSEC-6-DEL_RX_SC

6-Information

[chars] RX SCI %llx : vport [dec]\n

MKA request MACsec PD to delete a RX SC on the given RX SCI and vport.

-

"No action required normal operation."

MACSEC-6-INSTALL_TX_SA

6-Information

[chars] TX SCI %llx : vport [dec] : an [dec] : next_pn 0x[hec]\n

MKA request MACsec PD to install a TX SA on the given TX SCI vport and an.

-

"No action required normal operation."

MACSEC-6-INSTALL_RX_SA

6-Information

[chars] RX SCI %llx : vport [dec] : an [dec] : secy_vport [dec]\n

MKA request MACsec PD to install a RX SA on the given RX SCI vport and an.

-

"No action required normal operation."

MACSEC-6-DEL_RX_SA

6-Information

[chars] RX SCI %llx : vport [dec] : an [dec]\n

MKA request MACsec PD to delete a RX SA on the given RX SCI vport and an.

-

"No action required normal operation."

MACSEC-6-POST_SUCC

6-Information

[chars] Power-On-System-Test success in Trial No.[dec]\n

MACSEC power-on-system-test successful

-

"No action required normal operation."

MACSEC-6-POST_FAIL

6-Information

[chars] Power-On-System-Test failure in Trial No.[dec]\n

MACSEC power-on-system-test failed

-

"No action required normal operation."

ENVIRONMENTAL-3-TDLERROR

3-Error

Error processing TDL message. [dec]

An unexpected condition in which IOS has received a TDL\n\ message which it can not process.

iosxe-chassismgr

LOG_STD_ACTION

ENVIRONMENTAL-1-ALERT

1-Alert

[chars] Location: [chars] State: [chars] Reading: [dec] [chars]

One of the sensors in the system is reading an out of normal\n\ value.

iosxe-chassismgr

LOG_STD_ACTION

ENVIRONMENTAL-6-NOTICE

6-Information

[chars] Location: [chars] State: [chars] Reading: [dec] [chars]

Informational message on the sensor reading

iosxe-chassismgr

LOG_STD_ACTION

ENVIRONMENTAL-5-SENSOROK

5-Notice

[chars] Location: [chars] State: normal

One of the sensors in the system had been in a failure condition\n\ but is now operating normally.

iosxe-chassismgr

LOG_STD_ACTION

ENVIRONMENTAL-1-SENSORFAIL

1-Alert

[chars] Location [chars] State: fail

One of the sensors in the system has detected a failure condition\n\ from which it can not recover. This sensor is no longer reporting\n\ readings to the environmental monitoring subsystem.

iosxe-chassismgr

LOG_STD_ACTION

ENVIRONMENTAL-3-CHASFSERR

3-Error

Sensor [chars] on FRU [chars] has an invalid chasfs device state [chars]

The system does not understand the state that the sensor is \n\ reporting. This is most likely a filesystem corruption or\n\ ISSU problem. You may try rebooting the router to see if the\n\ problem corrects itself.

iosxe-chassismgr

LOG_STD_ACTION

ENVIRONMENTAL-6-INFO

6-Information

[chars]

Informational message of ambient sensor reading

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-3-MSGDISPATCHNULL

3-Error

Received NULL TDL message from IOS

An unexpected condition in which IOS has received a NULL TDL message from Chassis Manager.

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message '[chars]' from Chassis Manager. LUID: [chars]

An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages from Chassis Manager.

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-3-MSGIPCERR

3-Error

Unable to process received IPC messages from Chassis Manager error: [chars]

An unexpected condition has occurred while IOS is trying to process a received IPC message from Chassis Manager.

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-3-INVERR

3-Error

Unable to process chassis inventory for file [chars] slot [dec] [chars] error [dec]. Some SPA's may not be fully configured

An unexpected condition has occurred while IOS is trying to process the chassis inventory on startup. IOS can not determine the type and number of all Carrier Cards and SPA's present in the system. Some configuration relating to these SPA's may not be applied and leave the system in an inconsistent state.

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-3-INVERRSPA

3-Error

Unable to process chassis inventory for file [chars] SPA subslot [dec]/[dec] [chars] error [dec]. Some SPA's may not be fully configured

An unexpected condition has occurred while IOS is trying to process the chassis inventory on startup. IOS can not determine the type and number of all Carrier Cards and SPA's present in the system. Some configuration relating to these SPA's may not be applied and leave the system in an inconsistent state.

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-2-CRASHDUMP

2-Critical

Fatal error calling crashdump error: [dec] [chars]

A fatal condition has occurred causing IOS to crashdump.

iosxe-chassismgr

LOG_STD_ACTION

CMANRP-6-CMSTATUS

6-Information

Chassis Manager Process is [chars]

The current status of Chassis Manager Process.

-

LOG_STD_NO_ACTION

CMANRP-6-CMHASTATUS

6-Information

RP switchover [chars]

RP switchover events received by chassis manager.

-

LOG_STD_NO_ACTION

CMANRP-6-CMSWREAD

6-Information

RP switchover event triggered

RP switchover event triggered by IOS fastpath.

-

LOG_STD_NO_ACTION

CMANRP-3-CMREADFAIL

3-Error

Read from cpld_ha fd [dec] failed errno [dec] event cnt [dec]

Read from cpld_ha device returned 0 bytes.

-

LOG_STD_NO_ACTION

CMANRP-6-CMNOTSWITCH

6-Information

RP is not doing switchover

Read from cpld_ha device indicate no switchover event.

-

LOG_STD_NO_ACTION

CMANRP-3-CMSWVERINFO

3-Error

Unable to process software version information using file [chars]. Reason: [chars]. Error: [dec]

An unexpected condition has occurred while IOS was trying to process the software version information file. As a result version information may not be available to an SNMP Manager

iosxe-chassismgr

LOG_STD_NO_ACTION

CMANRP-3-UDEVPERMS

3-Error

An invalid permissions value [chars] was found in a udev file

The udev files for a particular filesystem contain a description the file system. If the permissions attribute is not recognized then this file system may run with incorrect permissions.

iosxe-chassismgr

LOG_STD_NO_ACTION

CMANRP-4-SMU_UNCOMMITTED

4-Warning

There are uncommitted SMU abort reload and 'install commit' if required

There are uncommitted SMU activity in the system reload will remove this SMU activity use 'install commit' to make it persistent.

iosxe-p-smu

LOG_STD_NO_ACTION

CMANRP-6-SMU_COMMITTED

6-Information

'install commit' is success.

There were uncommitted SMU activity in the system reload will remove this SMU activity with user input install commit is done.

iosxe-p-smu

LOG_STD_NO_ACTION

CMANRP-3-SMU_COMMITTED_FAILED

3-Error

'install commit' failed [dec] during reload.

There are uncommitted SMU activity in the system reload will remove this SMU activity with user input install commit is tried but failed with the error code mentioned in message.

iosxe-p-smu

LOG_STD_NO_ACTION

IOSXE_PEM-6-INSPEM_FM

6-Information

PEM/FM [chars] inserted

The platform detected the insertion of a power/fan module in the slot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_PEM-6-REMPEM_FM

6-Information

Power Supply/Fantray module [chars] removed

The platform detected the removal of a power/fan module in the slot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_PEM-6-PEMOK

6-Information

The PEM in [chars] is functioning properly

The PEM hardware may have been either switched off or reporting a failure condition. This message indicates that the PEM is no longer either switched off or reporting a failure

-

LOG_STD_ACTION

IOSXE_PEM-3-PEMFAIL

3-Error

The Power Supply in [chars] is switched off or encountering a failure condition.

The PEM hardware has been either switched off or is reporting a failure condition.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_PEM-6-FANOK

6-Information

The fan in [chars]/[dec] is functioning properly

The fan was reporting a failure condition. This message indicates that the fan is no longer reporting a failure

-

LOG_STD_ACTION

IOSXE_PEM-3-FANFAIL

3-Error

The fan in [chars]/[dec] is encountering a failure condition

The fan's hardware is reporting that the fan is failing. This is most likely because the hardware detects the fan as spinning below the minimum speed.

-

LOG_STD_ACTION

IOSXE_PEM-3-PEMCHASFSERR

3-Error

The PEM in [chars] has encountered a system software error.

The PEM's underlying software for storing PEM state is not working properly.

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_PEM-3-TEMPERATURE_RAISE

3-Error

Sensor [chars] has reached maximum temperature value Leads to shutdown of the system

The Temperature sensor reaching maximum threshold value working properly.

-

LOG_STD_ACTION

IOSXE_PEM-3-FAN_FAIL_SHUTDOWN

3-Error

More than one [chars] has failed Leads to shutdown the system

The Temperature sensor reaching maximum threshold value working properly.

-

LOG_STD_ACTION

IOSXE_PEM-3-SSFP_TEMPERATURE_RAISE

3-Error

[chars] transceiver temperature reached threshold value Leads to shutdown of the system

The Temperature sensor reaching maximum threshold value working properly.

-

LOG_STD_ACTION

IOSXE_PEM-3-PEMREDLOWSTANDBY

3-Error

Cannot activate [chars] configuration. Total power budget of standby power supplies is [dec]W. Standby power must be greater than or equal to the largest power supply capacity [dec]W.

Operating in unprotected mode Should insert at least one ps in standby slots with a capacity greater than or equal to the largest capacity power supply in the system. The configuration will be applied automatically once requirements are met.

-

LOG_STD_ACTION

IOSXE_PEM-3-PEMREDNOPWR

3-Error

Cannot enable power redundancy mode [chars] because config would create mode with insufficient [chars] power

Configuration set by user is not valid as power supplies in the active slots do not contain enough power to meet the power requirements

-

"Insert additional power supplies and configure them to be active or " "configure current standby power supplies to active such that " "power requirements are met"

IOSXE_PEM-3-PEMREDALARM

3-Error

Cannot enable power redundancy mode [chars] because the system is in software alarm state caused by previous active power-supply failures while in redundancy

Configuration set by user cannot be accepted as there are previous active power supply failures while in redundancy. Letting redundancy with failed supplies would reduce the total available power

-

"Insert additional power supplies or restore all the previously failed supplies " "in active slots before the system went in Alarm state"

WCM_WRP_IPC-3-TDL_INIT_FAIL

3-Error

WCM RF proxy TDL Library initialization failed.rc=[dec]

TDL library initialization failure

polaris-infra

LOG_STD_ACTION

WCM_WRP_IPC-3-SESSION_REG_FAIL

3-Error

WCM RF proxy IPC session registration fails with erro code 0x[hec]

IPC session registration failure

polaris-infra

LOG_STD_ACTION

WCM_WRP_IPC-3-SESSION_SEND_FAIL

3-Error

WCM RF proxy IPC session send [chars] fails - error code ox[hec]

IPC session transmit side encounters failure

polaris-infra

LOG_STD_ACTION

WCM_WRP_IPC-3-SESSION_RCV_FAIL

3-Error

WCM RF proxy IPC session receive [chars] fails reason [chars]

IPC session receive end encounters failure

polaris-infra

LOG_STD_ACTION

WCM_WRP_IPC-6-RF_RELAY_INFO

6-Information

WCM RF proxy relay RF information: type 0x[hec] value 0x[hec]

Display the content that WCM RF proxy relays to WCM

polaris-infra

LOG_STD_ACTION

WCM_WRP_IPC-6-SESSION_STATUS

6-Information

WCM RF proxy IPC session status: [chars]

Display the WCM RF proxy IPC session status information

polaris-infra

LOG_STD_ACTION

WCM_WRP-3-RF_ADD_CLIENT_FAIL

3-Error

WCM RF proxy RF client add fails return code=[dec]

IOS RF infrastructure add as RF client fails

polaris-infra

LOG_STD_ACTION

WCM_WRP-3-INVALID_CLIENT_ID

3-Error

WCM RF proxy received RF [chars] callback with wrong client ID [dec]

IOS RF infrastructure callback client ID argument is invalid

polaris-infra

LOG_STD_ACTION

ALARM_PERSISTENCY-6-ALARM_CHUNK_QUEUE_CREATED

6-Information

[chars]

Created the chunk-pool for the persistent alarm queue

-

LOG_STD_NO_ACTION

ALARM_PERSISTENCY-3-ALARM_PROFILE_NULL

3-Error

[chars]

Alarm profile is enabled with a wrong profile name

-

LOG_STD_ACTION

ALARM_PERSISTENCY-3-ALARM_CHUNK_QUEUE_FAIL

3-Error

[chars]

Failed to create the chunk-pool for the persistent alarm queue

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-6-ALARM_CHUNK_INFO_CREATED

6-Information

[chars]

Created the chunk-pool for the persistenct alarm info

-

LOG_STD_NO_ACTION

ALARM_PERSISTENCY-3-ALARM_CHUNK_INFO_FAIL

3-Error

[chars]

Failed to create the chunk-pool for the persistent alarm info

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-6-ALARM_RECORDS_FULL

6-Information

Persistent alarm info queue is full with [dec] elements

persistent alarm_records in the persistence queue are full

-

LOG_STD_NO_ACTION

ALARM_PERSISTENCY-3-ALARM_INFO_NULL

3-Error

Persistent alarm queue alarm info is NULL

alarm_info of the persistence queue is NULL

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-3-ALARM_QUEUE_NULL

3-Error

Persistent alarm queue info is NULL

alarm_info of the persistence queue is NULL

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-3-ALARM_INFO_FILE_OPEN_ERROR

3-Error

Failed to open [chars]/[chars] file error:[chars]

Failed to open persistent_alarm_log file

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-3-ALARM_INFO_FILE_CREATE_ERROR

3-Error

Failed to create [chars]/[chars] file error:[chars]

Failed to create persistent_alarm_log file

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-6-ALARM_INFO_FILE_CREATED

6-Information

Successfully created [chars]/[chars] file

Successfully created alarm_persistency file

-

LOG_STD_NO_ACTION

ALARM_PERSISTENCY-6-ALARM_INFO_FILE_ROTATED

6-Information

Switching to [chars] file \nafter writing [dec] records to [chars] file

Switched to other file after reaching a specified limit

-

LOG_STD_NO_ACTION

ALARM_PERSISTENCY-3-ALARM_INFO_FILE_WRITE_ERROR

3-Error

Failed to write to [chars]/[chars] file actual:[dec] written:[dec] error:[chars]

Failed to open persistent_alarm_log file

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-3-ALARM_INFO_PROCESS_FAIL

3-Error

Failed to create mcprp_spa_persistence_logger process

Failed to create mcprp_spa_persistence_logger process

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-6-ALARM_INFO_PROCESS_CREATE

6-Information

created mcprp_spa_persistence_logger process:[dec]

Created mcprp_spa_persistence_logger process

-

LOG_STD_NO_ACTION

ALARM_PERSISTENCY-3-ALARM_INFO_CHUNK_DESTROY_FAIL

3-Error

Failed to destroy [chars] chunk pool

Failed to destroy a chunk pool

asr900-lotr-im

LOG_STD_ACTION

ALARM_PERSISTENCY-3-NULL_DATA_STRUCTURE

3-Error

[chars] is NULL

Data-structure is NULL

asr900-lotr-im

LOG_STD_ACTION

IOSXE_SERVICE_ENGINE-3-MSGOPENFAIL

3-Error

Cannot open interface [chars] [dec]

During the creation of a Service-Engine interface it is necessary to program the system parameters in the driver. The driver cannot be opened.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SERVICE_ENGINE-3-MSGSETFAIL

3-Error

Set id on interface [chars] [dec]

During the creation of a Service-Engine interface it is necessary to program the system parameters in the driver. The failed to accept the programming.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SERVICE_ENGINE-3-MSGINITFAIL

3-Error

Initialization of interface [chars] failed

The initialization of the interface mentioned in the error message has failed.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SERVICE_ENGINE-5-SRVENGNOTAVL

5-Notice

Service Engine Not Available

The Service Engine Not Available.

-

LOG_STD_NO_ACTION

SBC_SPF-3-INTERNAL

3-Error

An internal IOSd SBC error has been encountered[chars].

An internal error has been encountered.

iosxe-sbc

LOG_STD_ACTION

SBC_SPF-3-NOT_FOUND

3-Error

An unsolicited message has been received by SBC [chars] [dec]

-

-

-

SBC_SPF-3-ENQUEFAIL

3-Error

Enqueue of TDL message failed [chars].

-

-

-

NETCLK-5-NETCLK_CHANGE

5-Notice

Network clock source transitioned from priority [dec] [chars] to priority [dec] [chars]\n

This notice indicates a change in the clock source.

asr1k-iosd-infra

"No action required."

NETCLK-5-NETCLK_MODE_CHANGE

5-Notice

Network clock source not available. The network clock has changed to [chars]\n

-

asr1k-iosd-infra

"No action required"

NETCLK-5-NETCLK_PHASE_LOST

5-Notice

Network clock source not available. Phase-lost on clock priority [dec] [chars]\n

-

asr1k-iosd-infra

"No action required"

NETCLK-4-NETCLK_CMD_FAIL

4-Warning

NULL

This message indicates that a network clock command from RP to IOS-SR or SPAs has failed

asr1k-iosd-infra

"show logging and show network-clocks"

IOSXE_DSP-3-ENQUEFAIL

3-Error

Enqueue of TDL message failed [chars].

-

-

-

CTOKEN-3-INITFAIL

3-Error

Initialization of Consent Token facility failed [chars].

An unexpected condition has occurred which resulted in Consent Token facility failing to start. This is a serious problem and means that Consent Token facility will not be functional.

iosxe-ct-lib

LOG_STD_ACTION

CTOKEN-3-REQPROCFAIL

3-Error

Consent Token Request Processing facility failed [chars].

An unexpected condition has occurred which resulted in Consent Token facility failing to process a request. This means that some part of Consent Token facility will not be functional.

iosxe-ct-lib

LOG_STD_ACTION

CTOKEN-6-AUTH_UPDATE

6-Information

Consent Token Update [chars].

Consent Token authentication state change update

iosxe-ct-lib

LOG_STD_NO_ACTION

IOSXE_THROUGHPUT-3-INVALID_CONFIG

3-Error

No valid license found for the configured throughput level: [chars] kbps

Users has the boot up throughput set to non-default level without having the valid license.

iosxe-csl

"Install valid throughput license"

IOSXE_THROUGHPUT-3-EULA_NOT_ACCEPTED

3-Error

The EULA has to be accepted prior to throughput configuration.

Users need to accept EULA to activate the license

iosxe-csl

"Accept EULA for throughput license"

IOSXE_THROUGHPUT-3-CONF_FAILED

3-Error

Configuration failed. Installed license does not support the throughput level. Please install the valid license

An error occurred when the throughput configuration was attempted.

iosxe-csl

-

IOSXE_THROUGHPUT-3-INVALID_LEVEL

3-Error

An invalid throughput level: [chars] kbps was selected.

The configured throughput level is unknown

iosxe-csl

-

IOSXE_THROUGHPUT-6-LEVEL

6-Information

Throughput level has been set to [dec]00000 kbps

Throughput level has been set to a number

iosxe-csl

-

IOSXE_THROUGHPUT-3-SETUP_FAILED

3-Error

Throughput level setup failed. Boot up will be at the default throughput

An error occurred when licensing tried to setup the througput

iosxe-csl

-

IOSXE_LICENSE_POLICY_MANAGER-2-CONFIG_NULL

2-Critical

[chars]: Configuration is unavailable

License Configuration is undefined for this platform.

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-FEATURE_CONFIG_NULL

2-Critical

[chars]: Feature Configuration is unavailable

Feature Configuration is undefined for this platform.

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-FEATURE_MALLOC_FAILED

2-Critical

[chars]: Policy Mgr Feature Registration struct malloc failed

Memory allocation for Feature Registration Struct failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-FEATURE_NAME_NULL

2-Critical

[chars]: Feature name is NULL

License feature name string is NULL

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REG_FAILED

2-Critical

[chars]: Failed to register [chars] license feature result = [hex]

License Registration failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REQ_FAILED

2-Critical

[chars]: [dec]/[dec]: Lic request failed idx:[dec] feature=[chars] lic_cnt=[dec]

License Request failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REL_FAILED

2-Critical

[chars]: [dec]/[dec]: Lic release failed idx:[dec] feature=[chars] lic_cnt=[dec]

License Release failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REQ_GEN_FAIL

2-Critical

[chars]: [dec]/[dec]: Lic request failed

License Request failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REL_GEN_FAIL

2-Critical

[chars]: [dec]/[dec]: Lic request failed

License Release failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-BAY_MALLOC_FAILED

2-Critical

[chars]: Policy Mgr Bay DB malloc failed for [dec]/[dec]

Memory allocation for SPA/EPA failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-2-IF_MALLOC_FAILED

2-Critical

[chars]: Policy Mgr IF DB malloc failed for [dec]/[dec]

Memory allocation for SPA/EPA interfaces failed

asr1k-smart-lic

LOG_STD_ACTION

IOSXE_LICENSE_POLICY_MANAGER-6-LIC_REQ_SUC

6-Information

[dec]/[dec]/[dec]: License request is successful for [chars] feature

License release is successful port allowed to go down

DDTS_COMPONENT

"Nothing the system is working properly"

IOSXE_LICENSE_POLICY_MANAGER-6-LIC_REL_SUC

6-Information

[dec]/[dec]/[dec]: License release is successful for [chars] feature

License release is successful port allowed to go down

DDTS_COMPONENT

"Nothing the system is working properly"

IOSXE_LICENSE_POLICY_MANAGER-4-INSUF_LIC

4-Warning

[dec]/[dec]/[dec]: Insufficient [chars] license skipping license request assuming customer has honor license

Permanent/Evaluation licenses have exhausted skipping license request asuming customer has purchased license

DDTS_COMPONENT

"Nothing the system is working properly"

IOSXE_LICENSE_POLICY_MANAGER-4-DISABLE_MACSEC

4-Warning

[chars]: Disabling MACsec configuration due to insufficient license

Disabling MACsec configuration from port due to insufficient MACsec license

asr1k-port-lic

"Purchase/Install MACsec license"

IOSXE_PLATFORM-3-WDC_INVALID_LENGTH

3-Error

WDC length can not be determined: [dec]

WDC length was not retrieved properly

iosxe-csl

"Check if WDC is programmed on this device"

IOSXE_PLATFORM-3-WDC_NOT_FOUND

3-Error

WDC returned length: [dec]

WDC length was set to 0 which specifies probably WDC does not exist

iosxe-csl

"Check if WDC is programmed on this device"

IOSXE_PLATFORM-3-WDC_TLV_NOT_FOUND

3-Error

WDC TLV could not be read from the Quack device

WDC TLV couldn't be read from the Quack device

iosxe-csl

"Check if WDC is programmed on this device"

IOSXE_AUTHENTICATE-2-AUTHENTICATE_FAILED

2-Critical

The platform authentication failed

WDC authentication failed

iosxe-csl

"Check if WDC is programmed on this device"

IOSXE_LMANRP-3-MSGINITFAIL

3-Error

Failed to initalize required lman resource: [chars]

During the initialization of the resources required by lman a failure occured. This has prevented lman from being activated.

iosxe-csl

LOG_STD_ACTION

IOSXE_LMANRP-3-MSGOPERATION

3-Error

Unable to [chars] the [chars] to license manager i.e. lman daemon. Error: [dec]

An unexpected condition has occurred while IOS was trying to send a TDL message to lman daemon.

iosxe-csl

LOG_STD_ACTION

IOSXE_LMANRP-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message from lman daemon.

An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from lman daemon.

iosxe-csl

LOG_STD_ACTION

IOSXE_CSLIFS-3-ERROR_SETTING

3-Error

Error setting default file system [dec]

There is an error happened after calling function ifs_set_default_directory

iosxe-csl

"Check the csl filesystem"

IOSXE_LICENSE_RP-3-UNREGISTER_FAIL

3-Error

License unregistration not successful for feature [chars]

Unregistration failed as license was not released.

iosxe-csl

"License has to be released before unregistering"

IOSXE_CRYPTOBW-3-INVALID_CONFIG

3-Error

No valid license found for the configured crypto throughput level: [chars] kbps

The boot up crypto throughput has been set to non-default level without having the valid license.

iosxe-csl

"Install valid crypto throughput license"

IOSXE_CRYPTOBW-3-EULA_NOT_ACCEPTED

3-Error

The EULA has to be accepted prior to crypto throughput configuration.

Users need to accept EULA to activate the license

iosxe-csl

"Accept EULA for crypto throughput license"

IOSXE_CRYPTOBW-3-CONF_FAILED

3-Error

Configuration failed

An error occurred when the crypto throughput configuration was attempted.

iosxe-csl

-

IOSXE_CRYPTOBW-6-LEVEL

6-Information

Crypto Throughput level has been set to [chars] bps

Crypto Throughput level has been set to a number

iosxe-csl

-

IOSXE_CRYPTOBW-6-RESET

6-Information

Crypto Throughput level has been reset to default [chars] bps

Crypto Throughput level has been reset

iosxe-csl

-

IOSXE_SMART_AGENT-3-NOTIFY_OOC

3-Error

Pool is out of compliance

This pool is Out Of Compliance

iosxe-smart-agent

"The pool is out of compliance. Customer needs" "to update his license pool"

IOSXE_SMART_AGENT-6-NOTIFY_ENABLED

6-Information

Smart Licensing is now Enabled

Smart Licensing is Enabled

iosxe-smart-agent

-

IOSXE_SMART_AGENT-6-NOTIFY_DISABLED

6-Information

Smart Licensing is now Disabled

Smart Licensing is Disabled

iosxe-smart-agent

-

IOSXE_SMART_AGENT-6-NOTIFY_InC

6-Information

Pool is now in Compliance

Smart Licensing Pool in Compliance

iosxe-smart-agent

-

IOSXE_SMART_AGENT-6-NOTIFY_GRACEWILLEXPIRE

6-Information

Grace Period will Expire

Grace Period will expire

iosxe-smart-agent

-

IOSXE_SMART_AGENT-3-NOTIFY_NOT_AUTHORIZED

3-Error

Requested count [dec] for license level [chars] is in 'not authorized' state.

Authorization Code needs to be installed using 'license smart reservation install' CLI

iosxe-smart-agent

-

HMANRP-3-MSG_CREATE_FAIL

3-Error

Message creation failed [chars]

Could not create tdl message

polaris-emp-relay

LOG_STD_ACTION

HMANRP-3-MSG_GET_FAIL

3-Error

Message read failed [chars]

Could not fetch tdl message

polaris-emp-relay

LOG_STD_ACTION

HMANRP-3-MSG_GET_VALUE_FAIL

3-Error

Message get value failed [chars]

Could not fetch value from tdl message

polaris-emp-relay

LOG_STD_ACTION

HMANRP-3-SET_MSG_VALUE_FAIL

3-Error

TDL set value failed [chars]

Could not tdl message values

polaris-emp-relay

LOG_STD_ACTION

HMANRP-3-MSG_SEND_FAIL

3-Error

Message send failed [chars]

Could not send tdl message

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-EMP_ELECTION_INFO

6-Information

EMP active switch [dec] elected: [chars]

EMP election algorithm has been run and a switch has been elected as active EMP

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-EMP_NO_ELECTION_INFO

6-Information

Could not elect active EMP switch setting emp active switch to 0: [chars]

Could not elect active EMP switch

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-HMAN_IOS_CHANNEL_INFO

6-Information

HMAN-IOS channel event for switch [dec]: [chars]

Info on HMAN-IOS events

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-EMP_STATUS_RCVD

6-Information

EMP status [dec] received from switch [dec]

EMP status received from member HMAN

polaris-emp-relay

LOG_STD_ACTION

HMANRP-5-CHASSIS_DOWN_EVENT

5-Notice

Chassis [dec] gone DOWN!

Chassis removed event

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-ACTIVE_FLAG_SET

6-Information

EMP_RELAY: Status received from active setting active status flag

Setting active status flag prioritizes active switch for election

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-RESET_ACTIVE_FLAG

6-Information

EMP_RELAY: Resetting active status flag IOS config'd shut/no shut admin_state = [dec]

Resetting active status flag prioritizes active switch for election

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-EMP_PROCESS_START

6-Information

EMP_RELAY: Starting process for event monitoring

IOS-HMAN channel gone down possibly due to HMAN process dying. The EMP IOS process monitors if this channel has come upHMAN respawned

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-EMP_PROCESS_PREEMPT

6-Information

EMP_RELAY: Preempting and killing the monitoring process: [chars]

An event has occured which has rendered the watching process useless. So the system will kill this process since it is not needed anymore.

polaris-emp-relay

LOG_STD_ACTION

HMANRP-6-EMP_PROCESS_EVT_STOP

6-Information

EMP_RELAY: Stopping and killing the monitoring process: [chars]

The monitoring process has hit an event. The process has fulfilled its purpose it can now be killed.

polaris-emp-relay

LOG_STD_ACTION

IOSXE_RP_MGMTE-3-MSGCREATENULL

3-Error

Cannot allocate [chars] TDL message

An unexpected condition in which IOS cannot allocate TDL message for Management ethernet.

iosxe-tdl

LOG_STD_ACTION

IOSXE_RP_MGMTE-3-MSGTDLINITERROR

3-Error

Management ethernet interface messaging module initialization failed: Unable to initialize messaging: [chars]

The Management ethernet interface subsystem has failed to initialize the infrastructure for messaging with the Pluggable Services Daemon. Configuration of management ethernet modules cannot proceed.

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_RP_MGMTE-3-PROCESS_CREATE_FAIL

3-Error

Management ethernet statistics process creation failed

Can not create IOS process for RP management ethernet port statistics collection

iosxe-iosd-fastpath

LOG_STD_ACTION

DECLASSIFICATION-3-UNABLE_TO_RESET_CONFIG

3-Error

[chars]

The system is unable to reset the configuration

firmware

LOG_STD_ACTION

DECLASSIFICATION-5-CONFIG_IS_RESET

5-Notice

[chars]

The configuration is reset and the system will now reboot

firmware

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-NO_BUFF_FOR_SYNC

3-Error

The Checkpoint Faclity reported the error [chars] during a request for a buffer length of [dec]. This [chars] CF client has failed to synchronize a transaction to the Standby RP.

This error indicates that the buffer management within the Checkpoint Facility has either run out of buffers or has some other problem. If this occurs during Bulk Sync then Bulk Sync will terminate without completing. Otherwise the incremental Sync will fail.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-BUFF_OFFSET_NULL

3-Error

Unable to utilize the memory buffer provided by the Checkpoint Facility. This [chars] CF client has failed to Bulk Sync.

This error indicates the Checkpoint Facility is having problems recognizing its own buffer layout. If this occurs during Bulk Sync then Bulk Sync will terminate without completing. Otherwise the incremental Sync will fail.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-CF_SEND_BULK_NONBLOCKED

3-Error

The Checkpoint Facility reported the error [chars] while attempting to send a message. Bulk Sync of this [chars] CF client is terminating.

This error indicates the Checkpoint Facility has internal problems related to IPC and cannot perform a non-blocked send operation.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-DEFERRED_DURING_BULK_SYNC

3-Error

Encountered error [chars] while trying to place an [chars] transaction on the Deferred list during Bulk Sync for the [chars] CF client.

Unable to cache a deferred transaction while Bulk Sync is underway. This can adversely impact SSO state on the Standby RP.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-CF_SEND_INCR_NONBLOCKED

3-Error

The Checkpoint Facility reported the error [chars] while attempting to send a non-blocked message. The Incremental Sync transaction for this [chars] CF client cannot be sent to the Standby RP.

This error indicates the Checkpoint Facility has internal problems related to IPC.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-6-CFPEER_CANNOT_RECV

6-Information

The Checkpoint Peer is not ready to receive messages. The Incremental Sync transaction for this [chars] CF client will not occur.

This error indicates the Checkpoint Facility has signalled the peer has gone away.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-SEND_FAIL_RELOAD

3-Error

Checkpoint Facility Failed to send a [chars] transaction for this [chars] CF client. Reloading the Standby RP.

This indicates the underlying Checkpoint Facility could not deliver a message sent from the active RP to the standby RP. The process will automatically reload the standby RP.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-4-DEF_LIST_REMOVE

4-Warning

Failed to remove one entry from the Deferred Sync list for the [chars] CF client.

An unexpected condition occured during list maintenance.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-CF_CANNOT_REGISTER

3-Error

The call to add this [chars] CF client to the Checkpoint Facility failed with the error [chars]. This client is unable to proceed and will not be registered.

For some reason the Checkpoint Facility will not register this client. As a result the Standby will never receive synchronized state from this CF client on the Active RP The system is not capable of SSO and HA switchover.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RF_PEER_EVENT_BUFFER

3-Error

This [chars] RF client is unable to acquire an event buffer to send an RF peer message the error [chars] was returned.

This indicates the RF facility is unable to provide a message buffer needed to communicate with the RF peer. As a consequence the RF progression may be compromised.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RF_SEND_PEER

3-Error

This [chars] RF client encountered error [chars] when attempting to send a peer message.

This indicates the RF facility could not send a message to the RF peer. As a consequence the RF progression may be compromised.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RF_PROCESS_FAILED

3-Error

This [chars] RF client Failed to create the Bulk Sync Process.

The background process which performs the RF Bulk Sync failed to be created. As a consequence the Standby will never obtain the relevent SSO state to enable HA switchover.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RF_POOL_REGEN_PROCESS_FAILED

3-Error

The [chars] RF client Failed to create the Id Pool Regeneration process.

The background process which performs Flow Control Id Pool regeneration failed to start. As a consequence the Standby will never obtain the relevent SSO state to enable HA switchover.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RF_POOL_REGEN_ERROR

3-Error

Id Pool Regeneration encountered error code [dec] cannot switchover.

The background process which performs Flow Control Id Pool regeneration encountered an error. As a consequence the Standby does not have valid Flow Id pools and cannot progress to Active state.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RF_SPA_ID_REGEN_ERROR

3-Error

Error code [dec] encountered trying to regenerate spa [chars] identifier in slot/subslot [dec]/[dec]

-

-

-

IOSXE_RP_IF_FLOW_IDS-3-RF_IF_ID_REGEN_ERROR

3-Error

Error code [dec] encountered trying to regenerate interface flow-control identifer. If id [dec] resides in slot/subslot/port [dec]/[dec]/[dec].

-

-

-

IOSXE_RP_IF_FLOW_IDS-3-RF_ADD_CLIENT_FAILED

3-Error

The RF facility failed to add this [chars] client reason given is [chars].

An operation pertaining to the ISSU support for SPA MARMOT IDs failed \n\ to complete using the CF transport context with the reason specified

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-TRANSFORM

3-Error

[chars] of [chars] via CF failed

The ISSU negotiation with the peer failed to start for either the CF or\n\ IPC transport with the reason specified.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-6-READY

6-Information

[chars] peer not ready discarding [chars]

The synchronization attempt for the message has determined that the\n\ transport has lost communication with its peer. This is a normal\n\ situation which indicates that the standby route-processor is currently\n\ out of service implying a simplex redundancy mode.

-

-

IOSXE_RP_IF_FLOW_IDS-3-DECODE

3-Error

Decode via CF of [chars] failed

A message sent via the CF transport failed in its attempt\n\ to be decoded on the standby. The resultant action taken by the\n\ standby route processor is an attempt to resynchronize.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_IF_FLOW_IDS-3-RECEIVE

3-Error

Client reports message CF is [chars]

An attempt to receive and process a versioned negotiation or\n\ synchronization message has failed due to an internal error\n\ being detected by the information received from the CF component.

iosxe-binos-ha

LOG_STD_ACTION

WSMAN-3-INVALID_TRUSTPOINT

3-Error

\ Trustpoint associated with HTTP is either invalid or does not exist

This message indicates that Trustpoint attached to the HTTP is not valid or it does not exist. Ideally there is a need to create Trustpoint first and then attach to the HTTP process. Incase Trustpoint is created later then there is a need to restart HTTPS server

ng-web-infra

"Configure a valid trustpoint and attach it to HTTP"

IOSXE_RP_NV-3-NV_ACCESS_FAIL

3-Error

Initial read of NVRAM contents failed

This error happens when the contents of the NVRAM cannot be read during system initialization. The failure may be due to data corruption of the NVRAM contents. The initial configuration dialog will be entered and the configuration must be restored.

iosxe-binos-ha

LOG_STD_ACTION

IOSXE_RP_NV-3-BACKUP_NV_ACCESS_FAIL

3-Error

Initial read of backup NVRAM contents failed

This error happens when the contents of the backup NVRAM cannot be read during system initialization. The failure may be due to data corruption of the backup NVRAM contents. The primary nvram contents will be backed up here again.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM_BRKOUT-3-BRKOUTCMD_SYNCFAILED

3-Error

Failed to send Breakout command to hardware.

A messages that was sent to the hardware module was not delivered correctly. The failure most likely occurred because of incorrect switch number or non-existing breakout port number specified or a software communication error.

iosxe-iosd-infra

LOG_STD_ACTION

PLATFORM-3-NOMAC

3-Error

Can't allocate MAC address for interface [dec]/[dec]

MAC address allocation failed because of an incorrect slot and\n\ port combination which exceeds the maximum available hardware.

-

LOG_STD_ACTION

PLATFORM-6-SVL_MGMT_INTF_MISMATCH

6-Information

Warning: The management interface is different between active and standby.

The management interface has been configured differently between active and the standby switch

-

LOG_STD_NO_ACTION

PLATFORM-3-FPTE_INTF_MODE

3-Error

Front-panel ethernet mode configuration is not in sync with INTF_MODE rommon variable value. Please use 'write' command and reboot to fix this. 10G ports will work in default TE mode in this current boot

Front-panel ethernet mode configuration is not in sync with INTF_MODE rommon variable value. INTF_MODE rommon variable could have been over-written. Please use 'write' command and reboot to fix this. 10G ports will work in default TE mode in this current boot

-

LOG_STD_ACTION

PLATFORM-3-NOMAC_INTF

3-Error

Failed to allocate MAC address for interface [chars]

MAC address allocation failed for logical interface specified in the message.

-

LOG_STD_ACTION

PLATFORM-3-GEC_NOMAC

3-Error

Can't allocate MAC address for port-channel interface [dec]

MAC address allocation failed for the port-channel interface specified in the message. This may happen if the port-channel interface exceeds the maximum number of supported port-channel interfaces.

iosxe-iosd-infra

LOG_STD_ACTION

PLATFORM-3-NO_BASEMAC

3-Error

Can't retrieve base MAC address

Base MAC address determination failed at system start.

-

LOG_STD_ACTION

PLATFORM-6-HASTATUS

6-Information

RP switchover [chars]

RP switchover events received by platform code.

-

LOG_STD_NO_ACTION

PLATFORM-6-HASTATUS_DETAIL

6-Information

RP switchover [chars] count [dec]

RP switchover events received by platform code.

-

LOG_STD_NO_ACTION

PLATFORM-4-HASTATUS_WARN

4-Warning

RP HA status warning [chars]

Standby RP reports peer not present event. This is indicative of a IPC problem between IOSd and CMRP

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-HAKPA_FAIL

3-Error

RP HA Keepalive failure [chars]

Standby RP reports missing keepalives from Active. This is indicative of an IPC problem between peer IOSd processes

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-HASTATUS_FAIL

3-Error

RP switchover [chars] count [dec]

RP switchover failed to reach active state. The RP will be reset. This is indicative of a IPC problem between IOSd and CMRP

iosxe-binos-ha

"Make sure system achieves full redundant state " "after the RP reset. If not reload entire system"

PLATFORM-3-RF_PROG_FAIL

3-Error

Progression completion notification to chassis management failed [chars]

Could not notify the completion of the RF progression to the chassis management process. The system will potentially not be in a fully redundant state.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-6-RF_PROG_SUCCESS

6-Information

RF state [chars]

A marker to illuminate when the standby reaches a terminal state.

iosxe-binos-ha

LOG_NO_ACTION

PLATFORM-4-RELOAD_STANDBY

4-Warning

[chars] reload requested by [chars]. Reason [chars]

Unexpected configuration or states mismatch between Active and Standby RPs. Reloading Standby to synchronize the configuration or states.

iosxe-binos-ha

"None. This is expected behavior."

PLATFORM-3-RF_RELOAD_PEER

3-Error

Reload peer notification to chassis management failed [chars]

Could not notify Reload Peer to the chassis management process. The Standby peer could not be reloaded by the Active. The system will potentially not be in a fully redundant state.

iosxe-binos-ha

"Reload peer instance using the available CLI " "commands. If system does not achieve full " "Standby status after that the system must " "be reloaded"

PLATFORM-6-EVENT_LOG

6-Information

[chars]

An entry from the internal event log at reload on the standby RP. This is informational.

-

LOG_STD_NO_ACTION

PLATFORM-4-BOOTVAR_NOT_SET

4-Warning

Boot variable is not set. Leaving it blank

-

-

-

PLATFORM-4-BOOTVAR_TOO_SMALL

4-Warning

Boot variable buffer too small. Leaving it blank

Boot variable either does not exist or buffer is too small. Not able to set boot variable. Ignoring it.

asr1k-chassismgr

LOG_STD_NO_ACTION

PLATFORM-3-NVRAM_OPEN_FAIL

3-Error

Failed to open nvram - [chars].

The nvram device could not be opened.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-NVRAM_READ_FAIL

3-Error

Failed to read nvram - [chars].

The nvram contents could not be read.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-NVRAM_WRITE_FAIL

3-Error

Failed to write nvram - [chars].

Couldn't write into the nvram device.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-BACKUP_NVRAM_OPEN_FAIL

3-Error

Failed to open backup nvram - [chars].

The backup nvram device could not be opened.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-BACKUP_NVRAM_READ_FAIL

3-Error

Failed to read backup nvram - [chars].

The backup nvram contents could not be read.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-3-BACKUP_NVRAM_WRITE_FAIL

3-Error

Failed to write backup nvram - [chars].

Couldn't write into the backup nvram device.

iosxe-binos-ha

LOG_STD_ACTION

PLATFORM-6-SB_INIT_DELAY

6-Information

RF progression will be suspended due to standby initialization delay configuration setting. Standby initialization will resume after [dec] seconds

An informational message about the standby initialization delay configuration. RF progression will be delayed for the configured value. Bulk-sync and other progression events will not happen until after the configured delay value

-

LOG_STD_NO_ACTION

PLATFORM-6-SB_INIT_DELAY_END

6-Information

RF progression delay timer expired. Standby initialization will now continue

An informational message about the standby initialization delay configuration. RF progression will now continue since configured delay has expired

-

LOG_STD_NO_ACTION

PLATFORM-4-STATS_COLLECTION

4-Warning

Reducing statistics collection interval for SPA [chars] will impact the RP control plane

MIB statistics for HW counters are sent from CC to RP every 10 seconds by default changing the timer through CLI to send more often will increase RP CPU utilization and result in sending more IPC messages between CC and RP

iosxe-spa-infra

LOG_STD_NO_ACTION

PLATFORM-1-NOSPACE

1-Alert

[chars] : no space alarm assert

bootflash memory exhausted Delete the old file from boot flash to create space

-

LOG_STD_NO_ACTION

PLATFORM-4-LOWSPACE

4-Warning

[chars] : low space alarm assert

bootflash memory is very low Delete the old file from boot flash to create space

-

LOG_STD_NO_ACTION

PLATFORM-5-LOWSPACERECOVER

5-Notice

[chars] : low space alarm deassert

bootflash memory

-

LOG_STD_NO_ACTION

PLATFORM -4-MEMORYSIZE

4-Warning

Active and Standby memory configuration differ by more than 1 GB. Active = %lldKB Standby = %lldKB

The memory configuration on both the Supervisor is different by more than 1GB. Some of the functionality which is high availability aware and dependent on the memory like IOX will be impacted.

-

"Please upgrade/downgrade memory configuration on " "both the Supervisor to match the size"

PLATFORM -4-SDM_TEMPLATE

4-Warning

Mismatch in SDM templates configured on Active [chars] and Standby [chars]

The SDM template configured on the two Supervisors are different. Different SDM template would enable different sets of features on the active and standby supervisors. Table sizes configured for the common features may be different. These features will not function properly on switchover from one supervisor to another.

-

"Please configure the same SDM template on both Supervisors using " "'sdm prefer <template>' configuration command followed by a reload. " "Supervisors should be brought to hot-standby state and the SDM " "template configured such that the template gets applied to both " "the supervisors. Supervisors can also be brought up as standalone " "and SDM template configured on them one at a time followed by a " "reload."

PLATFORM-6-SDM_TEMPLATE_SYNC

6-Information

Detected Standby supervisor with different [chars] SDM template

A mismatch detected in SDM template configuration between Active and standby supervisors. However IOS automatically pushed the SDM template configured on Active Supervisor to Standby to avoid functionality or scale mismatch between Active and Standby supervisors.

-

LOG_STD_NO_ACTION

LSMPI-4-INJECT_FEATURE_ESCAPE

4-Warning

Egress [chars] packet delivered via legacy inject path

A packet with a CPP supported L3 encapsulation such as IP was

-

LOG_STD_ACTION

LIIN-3-VRFADD_FAIL

3-Error

Problem creating vrf

The LIIN config process failed to allocate a mandatory iVRF. The LIIN interface will not operate properly and cannot be recovered. Persistent access features and interactive commands will not work.

-

LOG_STD_ACTION

LIIN-3-VRFMODIFY_FAIL

3-Error

Problem adding LIIN interface to vrf table

The LIIN config process failed to assign the LIIN interface to its mandatory iVRF. The LIIN interface will not operate properly and cannot be recovered. Persistent access features and interactive commands will not work.

-

LOG_STD_ACTION

LIIN-3-SET_TABLEID_FAIL

3-Error

Installing [chars] LIIN interface tableid failed

This error happens when IOS failed to set tableid into linux kernel possibly due to either IOSd or kernel out of memory or corruption. In this case LIIN interface will not have VRF installed for the associated address family. The LIIN interface will not operate properly and cannot be recovered. Persistent access features and interactive commands will not work.

iosxe-iosd-infra

LOG_STD_ACTION

LIIN-3-SET_ACCESS_FAIL

3-Error

Installing LIIN interface access control failed

This error happens when IOS failed to set the access control function for the LIIN possibly due to IOSd out of memory or corruption. In this case LIIN interface setup will not proceed will not operate properly and cannot be recovered. Persistent access features and interactive commands will not work.

iosxe-iosd-infra

LOG_STD_ACTION

LIIN-6-TELNET_ALLOWED

6-Information

Telnet access allowed due to romvar: SR_INIT_SHELL

Telnet from shell to IOS allowed because rommon variable SR_INIT_SHELL is set with value aux_do_system_shell. Remove this value from SR_INIT_SHELL or unset SR_INIT_SHELL to disable the telnet access

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-INSCARD

6-Information

Card [chars] inserted in [chars]slot [chars]

The OIR facility detected the insertion of a card in the slot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-REMCARD

6-Information

Card [chars] removed from [chars]slot [chars]

The OIR facility detected the removal of a card from the slot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-ONLINECARD

6-Information

Card [chars] online in [chars]slot [chars]

The OIR facility detected the state change to online for the card in the slot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-OFFLINECARD

6-Information

Card [chars] offline in [chars]slot [chars]

The OIR facility detected the state change to offline for the card in the slot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-3-CARDERR

3-Error

Could not read state property for [chars] slot [dec]

The OIR facility detected a failure for exceeding the number of retries to find state chasfs property.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-SOFT_STARTSPA

6-Information

SPA[chars] restarted in [chars]

The SPA in the specified subslot is restarted by the command <CmdBold>hw-module subslot<NoCmdBold> <CmdArg>slot#/subslot#<NoCmdArg> <CmdBold>start<NoCmdBold>

-

LOG_STD_NO_ACTION

IOSXE_OIR-3-SPA_INTF_ID_ALLOC_FAILED

3-Error

Failed to allocate interface identifiers for SPA[chars] in slot/bay: [dec]/[dec]

Failed to get CC buffer and flow control identifiers for the SPA in the specified subslot Traffic cannot flow through the SPA under this failure condition. This can happen if the system runs out of available identifiers.

iosxe-spa-infra

"Try to reduce the number of interfaces" "configured in the system either by physically removing the SPAs" "or by changing the system configuration"

IOSXE_OIR-6-SOFT_STOPSPA

6-Information

SPA[chars] stopped in [chars] interfaces disabled

The SPA in the specified subslot is stopped by the command <CmdBold>hw-module subslot<NoCmdBold> <CmdArg>slot#/subslot#<NoCmdArg> <CmdBold>stop<NoCmdBold> The interfaces on that processor will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-SOFT_RELOADSPA

6-Information

SPA[chars] reloaded on [chars]

The SPA in the specified subslot is reloaded by the command <CmdBold>hw-module subslot<NoCmdBold> <CmdArg>slot#/subslot#<NoCmdArg> <CmdBold>reload<NoCmdBold>

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-SYNCSPA

6-Information

SPA [chars] reloading to come up in [chars] mode

The SPA in the specified subslot is reloaded by the command <CmdBold>hw-module subslot<NoCmdBold> <CmdArg>slot#/subslot#<NoCmdArg> <CmdBold>reload<NoCmdBold>

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-INSSPA

6-Information

SPA inserted in [chars]/[dec]

The OIR facility detected the insertion of a SPA in the subslot number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-REMSPA

6-Information

SPA removed from [chars]/[dec] interfaces disabled

The OIR facility detected the removal of a SPA from the subslot number specified in the message. The interfaces on that processor will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-INSSSFP

6-Information

Smart SFP inserted in port [chars]

The OIR facility detected the insertion of TSoP/VCoP SSFP in the port number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-REMSSFP

6-Information

Smart SFP removed from port [chars]

The OIR facility detected the removal of TSoP/VCoP SSFP in the port number specified in the message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-SPARELOAD

6-Information

SPA reloaded on subslot [dec]/[dec]

The SPA in the specified subslot is reloaded.

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-CARDRECONCILE

6-Information

SPA type changed on subslot [dec]/[dec] from [dec] to [dec]

The SPA in the specified subslot has been initialized and it has been detected that it is of a different type to the SPA that was previously in this subslot.

-

LOG_STD_NO_ACTION

IOSXE_OIR-3-OIRTWICE

3-Error

Subslot [dec]/[dec] OIR insertion/removal not paired up: [chars]

An internal OIR-related error occured for the specified SPA.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_OIR-3-QUIESCE_FAIL

3-Error

Quiesce failed for subslot [dec]/[dec] error = [dec]

The RP failed to contact the SPA during failover. The SPA will be reset.

iosxe-iosd-infra

LOG_STD_NO_ACTION

IOSXE_OIR-3-UNQUIESCE_FAIL

3-Error

Unquiesce failed for subslot [dec]/[dec] error = [dec]

The RP failed to unquiesce the SPA in the specified subslot. The SPA will be reset.

iosxe-iosd-infra

LOG_STD_NO_ACTION

IOSXE_OIR-3-POWER_CYCLE_IMMINENT

3-Error

The SPA in subslot [dec]/[dec] will be power cycled in [dec] seconds.

The SPA in the specified subslot will be power cycled in the amount of time specified in the error message.

-

LOG_STD_NO_ACTION

IOSXE_OIR-3-PROCMSG

3-Error

Process msg send failed for process[dec]

Process message send failed.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_OIR-3-MODULE

3-Error

Missing [chars] for [chars]

A hardware or software error occurred.

iosxe-iosd-infra

LOG_STD_SH_TECH_ACTION

IOSXE_OIR-3-SPA_MDR_FAIL

3-Error

Minimal Disruptive Restart process failed for SPA in subslot [dec]/[dec] reason [chars].

The SPA in the subslot failed Minimal Disruptive Restart. Minimal Disruptive Restart process is aborted and an attempt will be made to recover the SPA by resetting the SPA hardware.

iosxe-binos-ha

LOG_STD_NO_ACTION

PLIM_QOS-3-IOSXE_RP_PLIM_QOS_FAIL

3-Error

A software error while configuring the [chars] on slot [dec]

This error happens when IOS fails to send messages to configure the per slot qos parameters in forwarding plane

iosxe-qos

LOG_STD_ACTION

IOSXE_ETHERCHAN-6-LINK_MTU

6-Information

Interface [chars] MTU set to port-channel [chars] MTU [dec]

The MTU for the interface mentioned in the message is changed to match the MTU configured on the port channel interface

-

LOG_STD_NO_ACTION

IOSXE_ETHERCHAN-3-LINK_MTU_FAIL

3-Error

Failure in changing MTU of interface [chars] to port-channel [chars] MTU

The MTU for the interface mentioned in the message cannot be changed to match the MTU configured on the port channel interface

iosxe-fwdmgr

"Remove the link mentioned in the message from " "the port-channel group"

IOSXE_APS-3-GROUP_CONFIG_FAIL

3-Error

Group change for interface [chars] Group [dec] failed

Group change for interface has failed

iosxe-spa-pos

LOG_STD_ACTION

IOSXE_APS-3-CONFIG_FAIL

3-Error

config change for interface [chars] Group [dec] failed

config for an interface to forwarding plane has failed

iosxe-spa-pos

LOG_STD_ACTION

IOSXE_APS-3-FLOWIDDELETIONFAILED

3-Error

Deletion of APS flow ID with manager failed for interface [chars] group [dec]

An unexpected condition has occurred that deletion of\n\ APS flow ID.

iosxe-spa-pos

"show interface"

IOSXE_APS-3-FLOWIDALLOCFAILED

3-Error

Allocation of APS flow ID with manager failed for interface [chars] group [dec]

An unexpected condition has occurred that allocation of\n\ APS flow ID. failed

iosxe-spa-pos

"show interface"

IOSXE_APS-3-PAIR_CONFIG_FAIL

3-Error

Pair config for interface [chars] Group [dec] failed

Pair config for interface has failed

iosxe-spa-pos

LOG_STD_ACTION

IOSXE_APS-3-CCCONFIGFAILED

3-Error

Pair config for interface [chars] Group [dec] failed

Pair config for interface has failed

iosxe-spa-pos

LOG_STD_ACTION

IOSXE_APS-3-FLOWCONFIGTOCCFAILED

3-Error

Flow id to cc for interface [chars] Group [dec] failed

Flow id to cc for an interface has failed

iosxe-spa-pos

LOG_STD_ACTION

IOSXE_APS-3-DOWNLOADFAIL

3-Error

Unable to download [chars] message to [chars]

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the reported process.

iosxe-spa-pos

LOG_STD_ACTION

INTERCHASSIS_REDUNDANCY-4-STDBY_PRESENT

4-Warning

Removal of standby RP in location [chars] is recommended for inter-chassis redundancy configuration

Removal of standby RP from the chassis is recommended for inter-chassis redundancy

iosxe-b2b-ha

LOG_STD_ACTION

MCPRP_DAI-4-ERR_DISABLE

4-Warning

DAI detected error on [chars] putting [chars] to err-disable

Dynamic ARP inspection has detected an error condition because ARP packets have exceeded the configured rate or burst

dai

LOG_STD_ACTION

UDEV-3-UDEVPERMS

3-Error

An invalid permissions value [chars] was found in a udev file

The udev files for a particular filesystem contain a description the file system. If the permissions attribute is not recognized then this file system may run with incorrect permissions.

iosxe-chassismgr

LOG_STD_NO_ACTION

PLATFORM-3-REDMODE_FAIL

3-Error

Redundancy mode: [chars] rc [dec]

Redundancy mode change could not be processed. This is indicative of a IPC problem between IOSd and the peer platform process.

iosxe-binos-ha

"Make sure system achieves full redundant state." "If not reload entire system"

IOSXE_DNS-3-UPDATE_FAILED

3-Error

Update resolv.conf vrf [chars] rc [dec]

An unexpected condition has occurred while updating the DNS file

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_DNS-3-VRF_FAILED

3-Error

Operation [chars] on /etc/netns/[chars] rc [dec]

An unexpected condition has occurred while updating the DNS directory

iosxe-iosd-infra

LOG_STD_ACTION

LICENSING-6-LIC_MISMATCH

6-Information

Configured license image level [chars] does not match the current level [chars]. Reload is required to bring the system up in [chars]

During boot-up of system the configured license image level might mismatch with the current level. This could happen when customer copy a different startup-config to the system.

polaris-license

"Reload is required to bring the system up in " "the configured license image level."

IOSXE_UEA-3-INVALID_EEPROM

3-Error

MAC count from BP is supposed to be 512 for NCS. Actual MAC count[dec]

For UEA NCS platforms MAC count must be 512

uea-systems

"Please program the EEPROM to correct MAC count"

IOSD_INFRA-6-IFS_DEVICE_OIR

6-Information

Device [chars] [chars]

USB inserted/removed

-

LOG_STD_NO_ACTION

IOSD_INFRA-3-IFS_DEVICE_DETECT_FAIL

3-Error

Device [chars] [chars]

USB detection failed

-

"USB Insertion could not be handled completely." "Device needs to be removed and re-inserted"

SDFLASH-6-DEVICE_ENABLED

6-Information

SDFlash device enabled

SDFlash device is enabled in the system.

-

LOG_STD_NO_ACTION

SDFLASH-1-DEVICE_DISABLED

1-Alert

SDFlash device disabled

SDFlash device is disabled from the system. Please enable it for correct operation of the switch.

-

LOG_STD_ACTION

USBFLASH0-6-DEVICE_ENABLED

6-Information

usbflash0 device enabled

usbflash0: is enabled in the system.

-

LOG_STD_NO_ACTION

USBFLASH0-1-DEVICE_DISABLED

1-Alert

usbflash0 device disabled

usbflash0: is disabled from the system.

-

LOG_STD_ACTION

USBFLASH1-6-DEVICE_ENABLED

6-Information

usbflash1 is enabled

usbflash1: is enabled in the system.

-

LOG_STD_NO_ACTION

USBFLASH1-1-DEVICE_DISABLED

1-Alert

usbflash1 device disabled

usbflash1: is disabled from the system.

-

LOG_STD_ACTION

HA-6-TOOBIG

6-Information

Running config too big config sync failed

The running config was too big to be synced

-

LOG_STD_NO_ACTION

HA-6-SWITCHOVER

6-Information

Route Processor switched from standby to being active

This RP switched to become the active RP

-

LOG_STD_NO_ACTION

IOSXE_OIR-6-CLEAR_FAKE_SPA

6-Information

Insert Event received for subslot [dec]/[dec] FAKE_SPA->NONE

The OIR facility detected the insertion of a SPA from the subslot number specified in the message. SPA insertion happened while standby Supervisor is booting up. This results into config mismatch which software can't handle and this will cause standby to go for reload.

-

LOG_STD_NO_ACTION

BOOT-6-MODECHANGE

6-Information

[chars]

This log indicates that device-mode operation is successful While mode change and there are no errors seen

-

LOG_STD_NO_ACTION

BOOT-3-MODECHANGE_FAIL

3-Error

[chars]. Requested by [chars]

This log indicates that device-mode operation failure While device-mode change and there are errors seen and requested by specified client

-

LOG_STD_NO_ACTION

MACSEC-5-UNSUPPORTED_SUP

5-Notice

MACsec is not supported on supervisor HW version [dec] in slot [dec]

This log indicates that Macsec is not supported on a given port

coresw-macsec

LOG_STD_NO_ACTION

SNP_RP-3-SNMP_TRAP_SEND

3-Error

Error in forwarding SNMP trap to confd: [chars]

An unexpected condition has occurred while IOS is trying to forward an SNMP trap to the DMI subsystem

polaris-dmi-infra

LOG_STD_ACTION

SNP_RP-3-UPDATE_FILTERS

3-Error

Error in updating trap filter list: [chars]

An unexpected condition has occurred while IOS is trying to update the list of trap filters from the cisco-ia model

polaris-dmi-infra

LOG_STD_ACTION

SNP_RP-3-UPDATE_FILTER_RESULTS

3-Error

Error in retrieving trap filter list: [chars]

The number of trap filters that can be configured in the cisco-ia YANG model is limited. Please check the limit in the model and reduce the number of trap filters configured.

polaris-dmi-infra

LOG_STD_ACTION

SNP_RP-3-ADD_FILTER

3-Error

Error in adding filter to list: [chars]

An unexpected condition has occurred while IOS is trying to add a new filter to the list of traps to be forwarded to the DMI subsystem

polaris-dmi-infra

LOG_STD_ACTION

SNP_RP-3-UPDATE_PROCESS

3-Error

Error in creating cisco-ia update process

Could not create IOS process to update the cisco-ia model

polaris-dmi-infra

LOG_STD_ACTION

CMM-3-CONFIG_SIZE_EXCEED_LIMIT

3-Error

Current config size is greater than supported size [dec]. Config CLI will not be synced to Centrally Managed Mobility Agents.

The Maximum supported configuration size which can be synced has been reached hence no new configuration will be synced from Mobility Controller to Centrally Managed Mobility Agents.

accsw-ease-of-use

"Save the current configuration on the Mobility " "Controller so that the existing configuration can be synced to " "the Centrally Managed Mobility Agents."

CMM-6-CONFIG_SYNC_SAVE_MSG

6-Information

Saving config rev#%llu received from Mobility Controller.

On receiving config from Mobility Controller the config is automatically saved on the Mobility Agent

accsw-ease-of-use

-

CMM-6-CONFIG_NOT_ALLOWED

6-Information

Centrally Managed MA: \[chars]\ cannot be locally configured.

This Mobility Agent is Centrally Managed hence this CLI is not allowed. Configuration needs to be done on the Mobility Controller.

accsw-ease-of-use

"show cmm config"

CMM-3-REGISTRY_ADD_ERR

3-Error

Failure in adding to [chars] registry

Could not add a function to the registry

accsw-ease-of-use

LOG_STD_NO_ACTION

CMM-6-CENTRAL_MANAGMENT_DISABLED

6-Information

This Mobility Agent is no more Centrally Managed.

This Mobility Agent is no more Centrally Managed as the feature has either been disabled on the Controller or the Controller does not support this capability. Check the output of show wireless mobility summary on controller.

accsw-ease-of-use

"show wireless mobility " "summary"

CMM-6-WIRELESS_MANAGEMENT_IP_CHANGED

6-Information

The Mobility Controller wireless management interface IP Address has been modified. Please reload the Mobility Controller.

The Mobility Controller wireless management interface IP Address has been modified. Please reload the Mobility Controller as this IP Address is used as the Domain ID for Central Management.

accsw-ease-of-use

LOG_STD_NO_ACTION

IOSXE_RP_ALARM-6-INFO

6-Information

[chars] [chars] [chars]: [chars] [chars]

-

-

-

IOSXE_RP_ALARM-6-INFO

6-Information

[chars] [chars] [chars] [chars] [chars]

Alarm assertion or deassertion information.

-

LOG_STD_NO_ACTION

IOSXE_RP_ALARM-2-PEM

2-Critical

[chars] [chars] [chars]: [chars] [chars]

-

-

-

IOSXE_RP_ALARM-2-PEM

2-Critical

[chars] [chars] [chars] [chars] [chars]

Power Entity Module missing information

-

LOG_STD_NO_ACTION

IOSXE_RP_ALARM-2-ESP

2-Critical

[chars] [chars] [chars]: [chars] [chars]

-

-

-

IOSXE_RP_ALARM-2-ESP

2-Critical

[chars] [chars] [chars] [chars] [chars]

No ESP running alarm information

-

LOG_STD_NO_ACTION

DSX-4-ALARM

4-Warning

[chars] [chars]: [chars]

The specified T1/E1 or T3/E3 Alarm has been asserted or cleared

-

"The recommended action is to isolate and repair the" " source of the asserted alarm"

GR_VRF_TOPO-3-VRF_TBL_OPEN

3-Error

Failed to open table type: [dec] root: 0x[hec] err: [chars] [dec]\n

Failed to open VRF mapping table.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-VRF_TBL_FREE

3-Error

Failed to free VRF table err: [chars] [dec]\n

Failed to free VRF mapping table.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-VRF_SET

3-Error

Failed to set vrf_name: [chars] vrf_id: 0x[hec] err: [chars] [dec]\n

Failed to set VRF mapping entry.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-VRF_GET

3-Error

Failed to get vrf_name: [chars] vrf_id: 0x[hec] err: [chars] [dec]\n

Failed to get VRF mapping entry.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-VRF_DEL

3-Error

Failed to delete VRF record 0x[hec] number: [dec]

Failed to delete VRF mapping entry.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-TOPO_TBL_OPEN

3-Error

Failed to open table type: [dec] root: 0x[hec] err: [chars] [dec]\n

Failed to open topology mapping table.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-TOPO_TBL_FREE

3-Error

Failed to free topology table err: [chars] [dec]\n

Failed to free topology mapping table.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-TOPO_SET

3-Error

Failed to set vrf_id: 0x[hec] afi: [dec] topology: [chars] topo_id: 0x[hec] err: [chars] [dec]\n

Failed to set topology mapping entry.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-TOPO_GET

3-Error

Failed to get vrf_id: 0x[hec] afi: [dec] topology: [chars] topo_id: 0x[hec] err: [chars] [dec]\n

Failed to get topology mapping entry.

-

GR_IOS_DB_ERR_ACTION

GR_VRF_TOPO-3-TOPO_DEL

3-Error

Failed to delete Topology record 0x[hec] number: [dec]

Failed to delete topology mapping entry.

-

GR_IOS_DB_ERR_ACTION

CVAC-2-INIT_FAILED

2-Critical

Virtual appliance configuration cannot occur: [chars]

The system was unable to even attempt to apply virtual appliance configuration for the given reason.

virt-infra

LOG_STD_SH_TECH_ACTION

CVAC-3-FILE_ERROR

3-Error

Could not [chars] file [chars]: [chars]

The system was unable to perform the indicated operation on the indicated file for the indicated reason

virt-infra

"Make sure the given disk is correctly formatted " "and has sufficient free space available."

CVAC-3-XML_ERROR

3-Error

Error while parsing XML from file [chars]: error '[chars]' element '[chars]' attribute '[chars]' explanation '[chars]'. File will be saved to [chars]

The contents of the given file were not correct XML and as a result XML parsing aborted due to the given reason. No new configuration was applied to the router from this file.

virt-infra

"Investigate the contents of the saved file " "to determine the cause of the reported error and " "if possible fix the file contents restore it to " "its original location and reload to re-process it. " LOG_STD_RECUR_ACTION

CVAC-3-CONFIG_ERROR

3-Error

[dec] errors while applying configs generated from file [chars].

Out of the generated virtual appliance configuration commands the given number of commands were rejected by the IOSd parser. The indicated log file will describe exactly which commands were rejected as will any accompanying CVAC-4-CLI_FAILURE messages in this log.

virt-infra

"Consult the indicated log file for details of the " "errors that were encountered. Also inspect the " "current running-config and startup-config of the " "router using the <CmdBold>show " "running-config<noCmdBold> and <CmdBold>show " "startup-config<noCmdBold> commands in order to " "confirm that the configuration is valid."

CVAC-4-FILE_IGNORED

4-Warning

Configuration file [chars] is ignored: [chars]

The indicated configuration file was ignored and not used for configuration for the given reason.

virt-infra

LOG_STD_NO_ACTION

CVAC-4-PROPERTY_IGNORED

4-Warning

Property key '[chars]' value '[chars]' ignored: [chars]

The indicated XML configuration property was ignored for the indicated reason

virt-infra

"If the property was not applied due to an invalid " "key or value either change these attributes to "

CVAC-4-CLI_FAILURE

4-Warning

Configuration command failure: '[chars]' was rejected

The indicated IOSd configuration command generated by the CVAC subsystem was rejected by the IOSd CLI. Look for a subsequent CVAC-3-CONFIG_ERROR log message which will contain a reference to a logfile containing more information about this failure.

virt-infra

"Inspect the log file to determine why the command " "was rejected and how to correct it. If necessary " "manually re-issue the corrected command."

CVAC-4-CONFIG_DONE

4-Warning

Configuration generated from file [chars] was applied and saved to NVRAM. See [chars] for more details.

The generated configuration was applied and the resulting system configuration has been saved to the startup-config in NVRAM. The indicated logfile may contain additional information.

virt-infra

LOG_STD_NO_ACTION

CVAC-4-WRITE_FAIL

4-Warning

Configuration generated from file [chars] was applied but could not be saved to NVRAM. See [chars] for more details.

The generated configuration was applied but the resulting system configuration was not saved to the startup-config in NVRAM. The indicated logfile may contain additional information.

virt-infra

"Issue the write memory command on the IOS CLI"

CVAC-5-XML_PARSED

5-Notice

[dec] lines of configuration generated from file [chars]

The indicated file was successfully parsed to generate IOSd configuration commands. The generated configs have not yet been applied to the system.

virt-infra

LOG_STD_NO_ACTION

CONFIG_CSRLXC-2-INIT_FAILED

2-Critical

CSRLXC configuration cannot occur: [chars]

The system was unable to even attempt to apply LXC configuration for the given reason.

ultra-ui

LOG_STD_SH_TECH_ACTION

CONFIG_CSRLXC-3-FILE_ERROR

3-Error

Could not [chars] file [chars]: [chars]

The system was unable to perform the indicated operation on the indicated file for the indicated reason

ultra-ui

"Make sure the given disk is correctly formatted " "and has sufficient free space available."

CONFIG_CSRLXC-3-CONFIG_NOT_SAVED

3-Error

Configuration not saved to NVRAM. Please inspect [chars] for details.

Out of the generated VM configuration commands the given number of commands were rejected by the IOSd parser. The configuration is only automatically saved to NVRAM if no errors are encountered so in this case it was not saved. The indicated log file will describe exactly which commands were rejected as will any accompanying CSRLXC-4-CLI_FAILURE messages in this log.

ultra-ui

"Inspect the current running-config of the router " "using the <CmdBold>show running-config<noCmdBold> " "command. If it appears valid you may manually save " "the configuration using <CmdBold>copy running-" "config startup-config<noCmdBold>. If it does not " "appear valid manually correct the configuration " "or use the <CmdBold>config replace nvram:startup-" "config<noCmdBold> command to revert to the " "startup-config."

CONFIG_CSRLXC-4-CLI_FAILURE

4-Warning

Configuration command failure: '[chars]' was rejected

The indicated IOSd configuration command generated by the CSRLXC subsystem was rejected by the IOSd CLI. Look for a subsequent CSRLXC-3-CONFIG_NOT_SAVED log message which will contain a reference to a logfile containing more information about this failure.

ultra-ui

"Inspect the log file to determine why the command " "was rejected and how to correct it. If necessary " "manually re-issue the corrected command."

CONFIG_CSRLXC-5-CONFIG_DONE

5-Notice

Configuration was applied and saved to NVRAM. See [chars] for more details.

The generated configuration was successfully applied no commands were rejected by the IOSd CLI and the

ultra-ui

LOG_STD_NO_ACTION

VXE_CINCO_IF_ADDR-3-ADDR_UPDATE

3-Error

VXE Cinco interface: [chars] address [chars] to linux [chars] failed with error [dec]

The interface IP address program to kernel interface failed.. BinOS application which need IOSd IP address may not work.

picasso-infra

LOG_STD_ACTION

VXE_CINCO_IF_ADDR-6-ADDR_VRFID_UPDATE

6-Information

VXE Cinco interface: [chars] address [chars] to linux [chars] not programmed for vrf_id [dec]

The interface IP address program to kernel interface not programmed.. BinOS application should only use global IP address for now.

-

-

VXE_MEMORY_UPGRADE-3-CONF_FAILED

3-Error

Configuration of memory failed.

An error occurred when memory configuration was attempted.

iosxe-csl

-

VXE_MEMORY_UPGRADE-3-SETUP_FAILED

3-Error

Memory upgrade setup failed. Memory upgrade operations may not be successful.

An error occurred when licensing tried to setup the memory upgrade

iosxe-csl

-

VXE_THROUGHPUT-3-SETUP_FAILED

3-Error

Throughput upgrade license set up failed

An error occurred when setting up the throughput upgrade licenses.

iosxe-csl

-

VXE_CLOUD_IMAGE-6-CLOUD_IMAGE

6-Information

System being booted in [chars] mode

-

-

-

VXE_CLOUD_IMAGE-3-THROUGHPUT

3-Error

Unexpected read value of desired throughput - [dec] kbps

-

-

-

VXE_THROUGHPUT-6-LEVEL

6-Information

Throughput level has been set to [dec]00 kbps

Throughput level has been set to a number

iosxe-csl

-

VXE_THROUGHPUT-6-CSL_TO_SL

6-Information

Transition to Smart license mode if there were Active CSL licenses prior to the transition please convert them to smart licenses

Transition to Smart license mode if there were Active CSL licenses prior to the transition please convert them to smart licenses

iosxe-csl

-

VXE_THROUGHPUT-2-LOW_THROUGHPUT

2-Critical

System throughput set to low default level 1000 kbps system performance can be severely impacted. Please install a valid license configure the boot level and reload to switch to a higher throughput

No valid Active license

iosxe-csl

-

VXE_THROUGHPUT-2-LOW_THROUGHPUT_LICENSE_GRACE_PERIOD_END

2-Critical

Grace period has expired. System throughput set to default level [dec]00 kbps system performance can be severely impacted. Please install a valid license to configure a higher throughput

No valid license installed. Register with smart account and request a license using 'platform hardware throughput level MB <>' CLI

csr1kv-csl

-

VXE_THROUGHPUT-6-THROUGHPUT_LICENSE_GRACE_PERIOD_MSG

6-Information

Grace period will expire in [dec] days and system throughput will be set to default level [dec]00kbps on expiration so system performance can be severely impacted. Valid license must be installed to avoid throughput being throttled.

System throughput will be set to default level on expiration of grace period and system performance can be severely impacted. Valid license must be installed to avoid throughput being throttled.

csr1kv-csl

-

VXE_THROUGHPUT-3-CONF_FAILED

3-Error

Configuration failed. Installed license does not support the throughput level. Please install the valid license

An error occurred when the throughput configuration was attempted.

-

-

VXE_METERING-3-CONFIG_FAILED

3-Error

Configuration failed.Failed to initialize metering service Falling back to limited throughput

Failed to initialize metering service

iosxe-csl

-

VXE_THROUGHPUT-3-EULA_NOT_ACCEPTED

3-Error

The EULA has to be accepted prior to throughput configuration.

Users need to accept EULA to activate the license

iosxe-csl

"Accept EULA for throughput license"

VXE_THROUGHPUT-3-INVALID_CONFIG

3-Error

Throughput level was not set or an invalid throughput level was selected.

The configured throughput level is unknown

iosxe-csl

-

VXE_THROUGHPUT-6-LOWER_THROUGHPUT

6-Information

Lower throughput is chosen because of the higher priority base license

If there is no configuration or the configuration could not be met premium has higher priority than advance and than standard.

iosxe-csl

-

VXE_THROUGHPUT-3-NOT_SUPORRT_LEVEL

3-Error

Memory license can only be used in premium level. Please configure license boot level to premium

Users has configured extra memory but CSR boots up in the level that does not support memory licenses.

iosxe-csl

-

VXE_THROUGHPUT-3-RELOAD_REQUIRED

3-Error

The transition from smart licensing mode to CSL mode needs a reload

We don't support the transition from smart licensing mode to CSL mode on the fly. A reload is required in this case

iosxe-csl

-

VXE_THROUGHPUT-6-CLI_RESTRICTED_LICENSE_EXPIRE

6-Information

System is in feature restricted mode due to license expiry. Configuration CLIs have been blocked. nvram:startup-config is write protected read-only.

System is in feature restricted mode due to license expiry. Configuration CLIs have been blocked. nvram:startup-config is write protected read-only.

iosxe-csl

-

VXE_THROUGHPUT-6-CLI_RESTRICTED_LICENSE_COMM_FAILED

6-Information

System is in feature restricted mode due to communication fault to license server. Configuration CLIs have been blocked. nvram:startup-config is write protected read-only.

System is in feature restricted mode due to communication fault to license server. Configuration CLIs have been blocked. nvram:startup-config is write protected read-only.

iosxe-csl

-

VXE_THROUGHPUT-6-EXTENDED_EVAL_START

6-Information

Entering extended evaluation period

System running configured features in extended 90 day evaluation period which begins immediately after standard 90 day smart agent eval expires.

csr1kv-csl

-

VXE_THROUGHPUT-6-EXTENDED_EVAL_EXPIRED

6-Information

Extended evaluation period expired

Extended 90 day evaluation period expired.

csr1kv-csl

-

VXE_THROUGHPUT-6-CLI_RESTRICTED_EVAL_LICENSE_EXPIRED

6-Information

System is in feature restricted mode due to evaluation license expiry. Configuration CLIs have been blocked. nvram:startup-config is write protected read-only.

System is in feature restricted mode due to evaluation license expiry. Configuration CLIs have been blocked. nvram:startup-config is write protected read-only.

csr1kv-csl

-

VXE_THROUGHPUT-6-AUTOSCALE_EVAL_EXPIRED

6-Information

Autoscale evaluation period has expired

Autoscale evaluation period has expired.

csr1kv-csl

-

VXE_CLOUD_IMAGE-4-PAYG_NOT_SUPPORTED

4-Warning

Pay-as-you-goPAYG is not supported in controller mode.You will be billed hourly as long as this VM is up.To Prevent this Either switch to Auto mode where PAYG is supported or switch to a BYOL instance

-

-

-

IOSXE_CSLIFS-3-ERROR_SETTING

3-Error

Error setting default file system [dec]

There is an error happened after calling function ifs_set_default_directory

iosxe-csl

"Check the csl filesystem"

VUDI-3-INCONSISTENT_VUDI

3-Error

[serial number: [chars]] [vUDI: [chars]] [chars]

vUDI inconsistency is detected between the license file in this VM and nvram configuration

virt-infra

LOG_STD_NO_ACTION

VUDI-4-ABNORMAL_EVENT

4-Warning

[serial number: [chars]] [vUDI: [chars]] [chars]

Abnormal vUDI condition occurs. vUDI subsystem is not working under normal flow

virt-infra

LOG_STD_NO_ACTION

VUDI-6-EVENT

6-Information

[serial number: [chars]] [vUDI: [chars]] [chars]

Normal vUDI event in system initialization

virt-infra

LOG_STD_NO_ACTION

VUDI-6-UPGRADE_EVENT

6-Information

Product upgrade detected. Using previous product id [chars] for licensing

Upgrade vUDI event in system initialization

virt-infra

LOG_STD_NO_ACTION

VUDI-6-UPGRADE_ERROR

6-Information

Product upgrade detected. Unable to determine previous product id - Defaulting to [chars] for licensing

Upgrade vUDI error in system initialization

virt-infra

LOG_STD_SH_TECH_ACTION

FGPT-3-INCONSISTENT_FGPT

3-Error

[container fingerprint: [chars]] [nvram fingerprint: [chars]] [chars]

Fingerprint inconsistency is detected between the license file in this VM and nvram configuration

virt-infra

LOG_STD_NO_ACTION

FGPT-6-EVENT

6-Information

[container fingerprint: [chars]] [nvram fingerprint: [chars]] [chars]

Normal container fingerprint event in system initialization

virt-infra

LOG_STD_NO_ACTION

VXE_CLOUD_METERING-3-CONF_FAILED

3-Error

Configuration failed for Metering Service

-

csr1k-cloud

-

VXE_CLOUD_METERING-4-PERSISTENT_FAILURE

4-Warning

Failed to set partial hr gbytes: [chars] with error: [dec]

-

-

-

VXE_CLOUD_METERING-4-PERSISTENT_FAILURE_OOC

4-Warning

Set persistent failed to set out of compliance [chars] hrs with error: [dec]

-

-

-

VXE_CLOUD_METERING-6-COMPLIANT

6-Information

[chars]

-

-

-

VXE_CLOUD_METERING-6-OUT_OF_COMPLIANCE

6-Information

[chars]

-

-

-

VXE_CLOUD_METERING-4-OUT_OF_COMPLIANCE_EXCEEDED_GRACE_PERIOD

4-Warning

[chars]

-

-

-

VXE_CLOUD_METERING-4-VARIANT_NOT_FOUND

4-Warning

Match not found. Variant is: [chars]\n

-

-

-

VXE_CLOUD_METERING-4-METERING_FLAG

4-Warning

[chars]

-

-

-

VXE_CLOUD_METERING-6-PARTIAL_HR_OOC

6-Information

Partial hour usage from previous boot will be treated as out-of-compliance until we've been able to report it. The partial hour value has been added to any outstanding OOC value which is now: [dec]ll. We will try to report this to AWS in the next hour to restore compliance!

-

-

-

VXE_CLOUD_METERING-4-OUTSTANDING_HRS_WARNING

4-Warning

[chars]

-

-

-

VXE_CLOUD_METERING-6-OUTSTANDING_HRS_INFO

6-Information

You have outstanding metering charges from a previous boot! We will try to restore your compliance in the next hour! You have been out-of-compliance for [dec] hours! Throughput will be restricted after [dec] hours!

-

-

-

VXE_CLOUD_METERING-6-OUTSTANDING_HRS_RELOAD_INFO

6-Information

[chars]

-

-

-

VXE_CLOUD_METERING-6-OUTSTANDING_HRS_REACHABILITY_INFO

6-Information

[chars]

-

-

-

VXE_CLOUD_METERING-6-TEST_MODE

6-Information

[chars]

-

-

-

VXE_CLOUD_HTTP-4-METERING_API_REQUEST_FAILURE

4-Warning

AWS httpc_send_request failed [hex]\nURL=[chars]\n

-

-

-

VXE_CLOUD_HTTP-4-METERING_API_POST_FAILURE

4-Warning

HTTP API Failure posting metering data failed with api_status: [dec]!

-

-

-

VXE_CLOUD_HTTP-4-METERING_API_RESPONSE_FAILURE

4-Warning

HTTP error posting metering data with status code: [dec] and response data: [chars]

-

-

-

VXE_CLOUD_HTTP-4-METERING_ROLE_FAILURE

4-Warning

HTTP API Failure getting role credentials with api status: [dec]

-

-

-

VXE_CLOUD_HTTP-4-METERING_ROLE_RESPONSE_FAILURE

4-Warning

HTTP API Failure getting role credentials with api status: [dec] and response data: [chars]

-

-

-

VXE_CLOUD_HTTP-4-METERING_API_HEADER_CREATION_FAILURE

4-Warning

Failed to create header and payload for metering request with role credentials [dec]

-

-

-

VXE_CLOUD_HTTP-4-METERING_URL_FAILURE

4-Warning

Could not open metering url in role credentials[dec]: [chars]

-

-

-

VXE_CLOUD_HTTP-4-METERING_OPEN_HEADER_FILE_FAILURE

4-Warning

Could not open header file in role credentials[dec]: [chars]

-

-

-

VXE_CLOUD_HTTP-4-METERING_DATA_FILE_FAILURE

4-Warning

Could not open data file in role credentials[dec]: [chars]

-

-

-

VXE_CLOUD_HTTP-4-METERING_PAYLOAD_FAILURE

4-Warning

Could not create request payload

-

-

-

VXE_CLOUD_HTTP-4-METERING_GET_ROLE_FAILURE

4-Warning

HTTP API Failure getting role name

-

-

-

VXE_CLOUD_HTTP-4-METERING_GET_ROLE_FAILURE_RESP

4-Warning

HTTP error getting role name: [dec]

-

-

-

VXE_CLOUD_HTTP-4-METERING_API_INIT_FAILURE

4-Warning

Could not initialize metering HTTP

-

-

-

VXE_VNIC_IF-3-MSGINITERROR

3-Error

VXE vNIC interface command: [chars] failed: [dec] for [chars]

The vNIC ethernet interface subsystem has failed to communicate with the infrastructure for port Configuration of vNIC ethernet.

vxe-iosd-infra

LOG_STD_ACTION

VXE_VNIC_IF-5-MSG_LCN_WARN

5-Notice

VXE vNIC interface: [chars] disabled due to the expired license

The vNIC ethernet interface disabled due to expired license.

vxe-iosd-infra

LOG_STD_ACTION

VXE_VNIC_IF-3-PROCESS_CREATE_FAIL

3-Error

vNIC ethernet [chars] process creation failed

Can not create IOS process for vNIC ethernet statistics

vxe-iosd-infra

LOG_STD_ACTION

VXE_VNIC_IF-3-HOT_FAIL

3-Error

vNIC ethernet hot processing failed - [chars]

vNIC hot add or remove event processing failed.

vxe-iosd-infra

LOG_STD_ACTION

VXE_VNIC_IF-3-PERSINITERROR

3-Error

Duplicate mac address in the VXE vNIC interface persistent name table: [enet]

There are two vNIC configured with the same mac address. This could cause inconsistency with the interface persistent.

vxe-iosd-infra

LOG_STD_ACTION

VXE_VNIC_IF-6-RING_CONF_FAILED

6-Information

Configurating ring entries failed

An error occurred when the ring size configuration was attempted.

ultra-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-6-VXE_UUID_CHANGED

6-Information

Router UUID changed from [chars] to [chars]

Router UUID is changed so persistent interface data is not used.

ultra-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-4-VXE_INSTANCE_ID_CHANGED

4-Warning

Router's cloud metadata based instance id changed from [chars] to [chars]

Router's instance id is changed so it may trigger UDI invalidation.

csr1k-cloud

LOG_STD_ACTION

VXE_VNIC_IF-6-VXE_UUID_INVALID

6-Information

Router has invalid or no UUID

Router UUID is invalid or not preset persistent interface data is not used.

ultra-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-4-DRIVER_NOT_SUPPORTED

4-Warning

Ignoring interface with address [chars] using unsupported [chars] driver.

Interfaces using an unsupported driver will not be configured.

csr1kv-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-4-DRIVER_DEPRECATED

4-Warning

Interface with address [chars] using deprecated [chars] driver.

Interfaces using an deprecated driver will not be supported in the next release.

csr1kv-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-6-INTF_CONFIG_RESTORED

6-Information

Address [enet] previously used for [chars] interface configuration restored.

An interface was added to the system using the same MAC address and device driver so the previous interface configuration is restored.

csr1kv-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-4-INTF_CONFIG_LOST

4-Warning

Address [enet] previously used for [chars] interface configuration not restored.

An interface was added to the system using the same MAC address but different device driver so the previous interface configuration is lost.

csr1kv-ethernet

LOG_STD_ACTION

VXE_VNIC_IF-4-UNITS_RESERVED

4-Warning

Unable to assign vNIC unit number to interface with address [enet]. Reload to re-use reserved unit numbers.

Unit numbers for previously removed vNICs are being reserved for re-use if the vNICs are re-added. Reloading the system should allow the new vNIC to be assigned a unit number.

vxe-iosd-infra

LOG_STD_ACTION

VXE_VNIC_IF-4-UNITS_EXHAUSTED

4-Warning

Unable to assign vNIC unit number to interface with address [enet]. All vNIC unit numbers have been assigned.

All vNIC unit numbers have been assigned and no more vNICs may be added.

vxe-iosd-infra

LOG_STD_ACTION

VXE_CLOUD_HA-6-BFDEVENT

6-Information

VXE BFD peer [inet] interface [chars] transitioned to down

The BFD interface transitioned to down triggering a VXE Cloud HA event.

vxe-iosd-infra

LOG_STD_NO_ACTION

VXE_CLOUD_HA-6-BFDCONFIG

6-Information

VXE BFD peer [inet] configuration [chars] from [chars]

The BFD configuration was removed while cloud HA is still configured

vxe-iosd-infra

LOG_STD_NO_ACTION

VXE_CLOUD_HA-6-BFDCONFIGV6

6-Information

VXE BFD peer [chars] configuration [chars] from [chars]

The BFD configuration was removed while cloud HA is still configured

vxe-iosd-infra

LOG_STD_NO_ACTION

VXE_CLOUD_HA-4-NOTCFGD

4-Warning

VXE Cloud HA BFD is enabled but [chars] node [dec] not fully configured flags=0x[hec]

The BFD state transitioned but not all Cloud paramerters were configured

vxe-iosd-infra

LOG_STD_NO_ACTION

VXE_CLOUD_HA-3-FAILED

3-Error

VXE Cloud HA BFD state transitioned [chars] node [dec] event [chars] failed

The BFD state transitioned but failed to perform route replacement

vxe-iosd-infra

LOG_STD_ACTION

VXE_CLOUD_HA-6-SUCCESS

6-Information

VXE Cloud HA BFD state transitioned [chars] node [dec] event [chars] successful

The BFD state transitioned and successfull performed the route replacement

vxe-iosd-infra

LOG_STD_ACTION

VXE_CLOUD_HA-3-INIT

3-Error

VXE Cloud HA [chars] failed

Memory allocated is not enough

iosxe-mibs

LOG_STD_ACTION

IOSXE_SUBSYS_EX-2-SUBSYS_EX_INIT_FAIL

2-Critical

Subsys exclusion init failed. Invalid subsys list.

Fail to initialize excluded subsystems to NULL. \n\ an abnormal condition

DDTS_COMPONENT

"This message means a software error had happened. \n" "The list of subsystems to be removed is not initialized. \n" "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative"

IOSXE_SUBSYS_EX-2-SUBSYS_REMOVE_FAIL

2-Critical

Unable to remove excluded subsystems.

Fail to remove excluded subsystems. \n\ an abnormal condition

DDTS_COMPONENT

"This message may be related to a memory corruption. \n" "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative"

IOSXE_SUBSYS_EX-2-SUBSYS_LIST_NOT_TERMINATED

2-Critical

Subsystems in exclusion list is not terminated correctly.

The subsystem exclusion list is not termianted \ by a NULL entry. \n It is \ an abnormal condition

DDTS_COMPONENT

"This message may be related to a memory corruption or hardware issue.\n\ \n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative"

IOSXE_PROCMIB -4-MSGERR

4-Warning

[chars] Error with process mib message from sub-slot [dec]/[dec]

When processing a process MIB message from the specified subslot the specified error has occurred.

iosxe-mibs

LOG_STD_ACTION

IOSXE_PROCMIB -4-SENDMSGERR

4-Warning

Failure in sending process mib information from subslot [dec]/[dec] to RP [chars]

A failure is encountered when sending process MIB statistics from the IOS driver for the subslot specified in the message to RP IOS. This indicates a software failure.

iosxe-mibs

LOG_STD_ACTION

DB_LOCK_MGR-3-INITFAIL

3-Error

Initialization of the Database Lock Manager facility failed [chars].

An unexpected condition has occurred which resulted in the Database lock manager facililty failing to start. This is a serious problem and means that the Database lock manager facility will not be functional.

crimson

LOG_STD_ACTION

DB_LOCK_MGR-3-OPERFAIL

3-Error

Database Lock Manager Operational failure [chars].

An unexpected condition has occurred which resulted in the Database lock manager detecting an operational failure. This means Database lock manager has detected and corrected an unexpected failure condition.

crimson

LOG_STD_ACTION

IOSXE_INFRA-3-INVALID_ERRMSG

3-Error

Error message type [dec] not defined

Error message type used is not defined in IOSXE infrastruction

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_INIT_WQ_FAIL

3-Error

IOSXE shim layer initialization failed: Can not create receiving queues

IOSXE IOS shim layer initialization of watched queue failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_INIT_WQ_CHASFS_FAIL

3-Error

IOSXE shim layer initialization failed: Can not create receiving chasfs watched queue

IOSXE IOS shim layer initialization of watched queue failed

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_INIT_PROC_FAIL

3-Error

IOSXE shim layer initialization failed: Dispatch process creation failed

IOSXE IOS shim layer initialization creating dispatch process failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_INIT_MEM_FAIL

3-Error

IOSXE shim layer initialization failed: Memory initialization failed.

IOSXE IOS shim layer initialization of memory failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_NO_IPC_DISPATCH_HDL

3-Error

IOSXE shim layer [chars] process message without IPC dispatch handler.

IOSXE IOS shim layer has no ipc dispatch handler set

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_RXMSG_NO_IPC_HDL

3-Error

IOSXE shim layer without IPC handler for fd [dec] seqnum [dec].

IOSXE IOS shim layer cannot find ipc handler

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_INIT_TDL_FAIL

3-Error

IOSXE shim layer initialization TDL Lib [chars] failed.

IOSXE IOS shim layer initialization of TDL library

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_INIT_DISPATCH_INIT_FAIL

3-Error

IOSXE shim layer initialization dispatch path init failed.

IOSXE IOS shim layer initialization of TDL disatch path

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-INVALID_RUNTIME_IDX

3-Error

Thread runtime index [dec] is not valid

Export the thread's running time failed.

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-6-THEAD_SELECT_ERR

6-Information

Inbound message or packet select error [chars].

Socket select operation error in threads

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-INJECT_HDR_LENGTH_ERR

3-Error

Inject hdr size [dec] exceeds limit

Inject header length exceeds pak header space

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-INJECT_EMBEDDED_HDR_LENGTH_ERR

3-Error

Can't allot space needed for embedded inject hdr size [dec] exceeds limit

Can't allot space needed for embedded inject header exceeds pak header space

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-INJECT_NO_IF_OUTPUT_ERR

3-Error

Output intf is NULL [chars]

Output intf is requred to proceed else skip the feautre

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_INV_PARAM

4-Warning

Invalid parameter: [chars]

Invalid parameter was passed when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_GET_FILE_NAME

4-Warning

Failed to get file name: [chars]

Punt keepalive log error seen

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_INV_FILE_ID

4-Warning

Invalid file descriptor: [dec]

Invalid file descriptor was found when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_OPEN_FILE

3-Error

Failed to open file: [chars]

Failed to open file when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_CLOSE_FILE

4-Warning

Failed to close file with descriptor: [dec]

Closing of file failed when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_WRITE_TO_FILE

3-Error

Write to file Id [dec] failed [dec] bytes expected [dec] bytes

Write to file failed when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_ALLOC_TTY

3-Error

Failed to allocate a tty

Can't allocate a TTY when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_ALLOC_CSB

3-Error

Failed to allocate a csb

Can't allocate a csb when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_PARSE_CMD

3-Error

Failed to parse command: [chars]

Failed to parse a command when generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_GET_PROCID

4-Warning

Failed to get process id

Can't get identifier of the process generating punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_INV_PROCID

4-Warning

Invalid proc id [dec] expected [dec]

Invalid process trying to generate punt err log

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-4-NO_PUNT_KEEPALIVE

4-Warning

Keepalive not received for [dec] seconds

Punt Inject keepalive message was not received

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-2-FATAL_NO_PUNT_KEEPALIVE

2-Critical

Keepalive not received for [dec] seconds resetting

Punt Inject keepalive message was not received

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-2-FATAL_PUNT_LINK_DOWN

2-Critical

Punt Inject link went down resetting

Punt Inject link went down

mcp-infrastructure

LOG_STD_ACTION

IOSXE_INFRA-3-INJECT_GSB_CTL_INIT_FAIL

3-Error

Inject adjacency subblock init failed

Adj subblock control or register failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_ADDR_RES_ENCAP_ERR

3-Error

Punted address resolution packet with unknown encap [chars]

Punted packet for ARP/ND with encap not supported

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_SVC_PROC_ERR

3-Error

Punt service [chars] create failed

Punt service process can not be created

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-VM_PAGE_TABLE_ERR

3-Error

VM guarded page operation failed address 0x[hec] [chars]

VM guarded page avl tree operation error

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-PUNT_SVC_TYPE_UNKNOWN

3-Error

Punted packet with unknown service type [dec]

Punted pak with an unsupported service type

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-5-PUNT_SVC_CANT_ENQUEUE

5-Notice

Punted pak can't be enqueued for service

Punted pak enqueue failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-5-PUNT_SVC_INVALID_OPT_PKT

5-Notice

Invalid IPv4 options packet punted to RP

Invalid IPv4 options packet dropped in RP

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-4-INJECT_TUN_NONIP_WARN

4-Warning

pak with linktype [chars] gets into non-ip tunnel

IP/IPv6/MPLS packet should to go through GRE tunnel for non-IP payload

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-INJECT_FEATURE_ESS_ERR

3-Error

ESS segment not found type [dec] hdl 0x%8x

Packets to be injected to an unsupported ESS segment

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-6-PROCPATH_CLIENT_HOG

6-Information

IOS shim client '[chars]' has taken %ld msec runtime: %ld msec to process

The specified IOSXE IOS shim client has taken too long to process a received IPC or chasfs message

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-6-AUXTHD_REQUEST

6-Information

Too many outstanding requests for file system access

Resource temporarily unavailable

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-APP_SESS_OPEN_FAILED

3-Error

An attempt to open [chars] with handle number [dec] has failed [dec]

Application session between processes failed to estabish.

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-CONSOLE_DBUG_DROP

3-Error

System dropped [dec] bytes of console debug messages.\n

Debugging messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

IOSXE_INFRA-3-PUNT_INCOMP_WRONG_ADJID

3-Error

Punted address resolution packet linktype [chars] adj-id [dec] is with linktype [chars]\n

CPP needs to punt incomplete adjacency for resolution by specifying the adjacency-id but the included adjacency-id does not match the incomplete adjacency this packet triggered.

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-IFS_EXTLINK_ADD_FAIL

3-Error

Could not add filesystem [chars] to IFS links

Attempt to add filesystem root to allow for links failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-IFS_UDEV_REMOVE_FAIL

3-Error

Could not remove udev device [chars]

Attempt to remove udev device failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-IFS_DFLT_FS_REG_FAIL

3-Error

Unable to set [chars] as a default file system.\n

IOSXE's platform dependent code failed to register the default file system.

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-IFS_INIT_HIDDEN_FAIL

3-Error

IOSXE shim layer initialization failed: Can not create receiving queues

IOSXE IOS shim layer initialization of hidden path watch failed

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-BSO_MSG_HDR_LENGTH_ERR

3-Error

BSO message header length [dec] is incorrect

BSO message header length is incorrect

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-BSO_MSG_HDR_MSGTYPE_ERR

3-Error

BSO message header msgtype [dec] is incorrect

BSO message header msgtype is incorrect

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-BSO_MSG_UNMARSHAL_ERR

3-Error

BSO message unmarshalling has failed

BSO message unmarshalling has failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-BSO_MSG_CACHE_ERR

3-Error

BSO message query cache update error - [chars]

BSO message query cache update error

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-4-BSO_MSG_RIB_WATCH_WARN

4-Warning

BSO message RIB watch start error

BSO message RIB watch start error

iosxe-p-punject

LOG_STD_ACTION

IOSXE_INFRA-3-RELOAD_INFO_SAVE_FAIL

3-Error

Unable to save reload information: [dec]: [chars].\n

IOSXE's platform dependent code failed to save the reload information.

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-3-SN_IPFRR_PROC_ERR

3-Error

Static Nexthop IPFRR [chars] create failed

SN IPFRR process can not be created

iosxe-iosd-fastpath

LOG_STD_ACTION

IOSXE_INFRA-6-CONSOLE_ACTIVE

6-Information

[chars]

Indicates that the current instance of IOS is assuming active control of the console. This is informational.

-

LOG_STD_NO_ACTION

IOSXE_INFRA-6-PLATFORM_RELOAD

6-Information

[chars]

Indicates that the current instance of IOS is being reset by the platform code. This is part of a normal reset sequence and the message is informational.

-

LOG_STD_NO_ACTION

IOSXE_INFRA-6-CHASFS_CLOCK_SET_FAIL

6-Information

Failed to set Chasfs property on system time change

Unable to set chasfs property on system time change

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_INFRA-6-HARDWARE_CLOCK_SET_FAIL

6-Information

Failed to set Hardware clock on system time change

Unable to set Hardware clock on system time change

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_INFRA-3-CYAN_API_ERROR

3-Error

Failed to retrieve platform dependent value of [chars] err=[dec]

CYAN API function failed

polaris-plat-abs

LOG_STD_ACTION

IOSXE_INFRA-6-SHIM_RXMSG_IPC_INFO

6-Information

IOS shim layer process IPC msg for fd [dec] seq_num [dec] ipc_status [dec]

-

-

LOG_STD_ACTION

IOSXE_INFRA-3-SHIM_IPC_NOT_PROCESSED

3-Error

msg handler returned FALSE for IPC msg for fd [dec] seq_num [dec] service [chars]

-

-

LOG_STD_ACTION

IOSXE_INFRA-3-SWIFT_ORCH_PROC_FAIL

3-Error

IOSXE SWIFT Orchestrator process creation failed

The SWIFT Orchestrator process could not be created

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-BAD_GLIBC_BUF_FREE

3-Error

An IOS buffer is freed into GLIBC buffer pool buffer blockmagic 0x[hec] flags 0x[hec]

An IOS buffer is freed into GLIBC buffer pool.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-BIPC_MGS_ALLOC_FAIL

3-Error

Allocating [dec] byte for IPC [chars] msg failed: out of memory

system is out of memory

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-SOCKET_PEEK_ERR

3-Error

Interrupt processing of Punt received packets over socket failed as peek of packet returned error: [chars]

Peek at incoming message hit error

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-GET_BUFFER_ERR

3-Error

Interrupt processing of Punt received packets over socket failed to get a packet buffer for len [dec]

Failed to get a packet buffer from the specified pool.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-SOCKET_RECV_ERR

3-Error

Interrupt processing of Punt received packets over socket failed as receive packet hit error: [chars]

Hit error when receives packet from a socket.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-SOCKET_SEND_ERR

3-Error

Transmit packet to the socket hit error: [chars]

Transmit a packet to another socket hit error.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-INJECT_HEADER_ERR

3-Error

Transmit packet to the socket failed as packet header length is greater than datagram size. It's an incorrect packet and cannot proceed sending. header length is [dec] datagram size is [dec].

Packet header length is wrong.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-IDB_CREATE_ERR

3-Error

Failed to create IDBInterface Descriptor Block for Punt/Inject

Creating an idb corresponding to an interface failed.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-MALLOC_FAST_ERR

3-Error

Failed to allocate memory for Punt/Inject socket instance

malloc_fast failed to allocate memory.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-IDB_INIT_ERR

3-Error

Failed to initialize IDBInterface Descriptor Block for Punt/Inject

Hit error when we initialize idb.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-PI_SOCKET_RAW_PRE_INIT_ERR

3-Error

Punt/Inject socket pre-initializationIDB creation failed

PI Socket Raw pre-initialization failed.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-PI_SOCKET_RAW_INIT_ERR

3-Error

Punt/Inject socket initialization failed

PI Socket Raw initialization failed.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-MCPRP_INIT_PUNTPATH_FD_ERR

3-Error

Initializing the ipc control for the puntpath fd failed

Initializing the ipc control for the puntpath fd failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-LIIN_TUN_MSG_ERR

3-Error

LIIN error - [chars] [chars] [dec]

LIIN in Tunnel mode experiencing error

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_INFRA-3-PI_TUN_INIT_ERR

3-Error

Punt/Inject TUN initialization - [chars] failed

PI TUN initialization failed.

picasso-infra

LOG_STD_ACTION

IOSXE_INFRA-3-TUN_RECV_ERR

3-Error

Interrupt processing of Punt received packets over TUN interface failed as read hit error: [chars]

Hit error when receives packet from TUN.

picasso-infra

LOG_STD_ACTION

IOSXE_INFRA-3-TUN_SEND_ERR

3-Error

Transmit packet to the TUN interface hit error: [chars]

Transmit packet to the TUN interface hit error.

picasso-infra

LOG_STD_ACTION

IOSXE_INFRA-3-TLS_TUN_HOST_IF_ERR

3-Error

TLS tunnel to host interface hit error: [chars]

TLS tunnel to host interface hit error

picasso-infra

LOG_STD_ACTION

IOSXE_INFRA-3-VRF_OPEN_CNTRL_FD_ERR

3-Error

Control fd open failed for VRF [chars] with error: [chars]

Control fd open failed for a specified VRF

picasso-infra

LOG_STD_ACTION

IOSXE_EPA-3-CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

Failed to create a SPA object.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-ACT2_AUTHENTICATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

ACT2 dev authentication Failed.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_EPASENSOR_PTR

3-Error

-

Pointer to a DEVSENSOR object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_PORT_PTR

3-Error

-

Pointer to a PORT object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_DEVPSEQ_PTR

3-Error

-

Pointer to a DEVPSEQ object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_DEVOBJ_PTR

3-Error

-

Pointer to a DEVOBJ object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_FPGA_PTR

3-Error

-

Pointer to a FPGA object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_EPA_PTR

3-Error

-

Pointer to an EPA object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_EPA_MODE_SB_PTR

3-Error

-

Pointer to an EPA mode subblock is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-SPA_PORT_NUM_FAILURE

3-Error

Failure in getting spa port number from card port [dec] for EPA in [dec]/[dec]

Failed to get spa port number from card port number

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-CARD_PORT_NUM_FAILURE

3-Error

Failure in getting card port number from spa port [dec] for EPA in [dec]/[dec]

Failed to get card port number from spa port number

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_VSC_PHY_INFO_PTR

3-Error

-

Pointer to a VSC PHY INFO object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-NULL_VFT

3-Error

-

Pointer to a DEVSENSOR object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-UNSUPPORTED_XCVR

3-Error

Transceiver type [chars] is not allowed on spa [chars] port [dec]

This transceiver is not allowed on the SPA

DDTS_COMPONENT

"Consult the documentation and ensure supported " "transceivers are plugged into the SPA"

IOSXE_EPA-3-AUTONEG_CFG_ERR

3-Error

interface [chars] autoneg state '[chars]' is incompatible with transciever. Remove \'[chars]\' to allow the transceiver.

Autoneg Config is not compatible. Remove autoneg config on the interface to allow the transceiver

DDTS_COMPONENT

"Remove the negotiation auto config or " "reinsert the previously enabled transceiver."

IOSXE_EPA-3-XCVR_EC_BWMISMATCH

3-Error

Trasnsceiver bandwidth is incompatible with Port-channel[dec] allowed bandwidth. Remove \'channel-group [dec]\' config for interface [chars] to allow the transceiver

The interface port into which the transceiver is inserted is part of a Port-channel. The Port-channel has member links whose bandwidth doesn't match with the inserted transceier's bandwidth. Since port-channel cannot allow heterogenous bandwidth links this transceiver is not allowed in to the port.

DDTS_COMPONENT

"Remove the channel-group config for the port where " "transceiver is inserted or insert a transceiver " "whose bandwidth is compatible with the port-channel " "bandwidth"

IOSXE_EPA-3-XCVR_PROHIBIT

3-Error

Transceiver is prohibited to come online for interface [chars]

XCVR is prohibited on the interface

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_EPA-3-EPA_PROHIBIT

3-Error

Insertion of [chars] not allowed in [dec]/[dec] post-boot

The SPA in the specified subslot cannot be inserted once the system boots up in controller mode

-

LOG_STD_NO_ACTION

IOSXE_EPA-3-NULL_EPA_PORT_CFG_PTR

3-Error

-

Pointer to an epa port cfg is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PLATFORM_ACT2-2-SUDI_VALIDATION_FAILED

2-Critical

Secure UDI validation failed. [chars]

Secure UDI validation for the chassis failed. The router failed to authenticate itself

iosxe-chassismgr

LOG_STD_ACTION

PLATFORM_TAM-2-SUDI_VALIDATION_FAILED

2-Critical

Secure UDI validation failed. [chars]

Secure UDI validation for the module failed. The module failed to authenticate itself

iosxe-chassismgr

LOG_STD_ACTION

IOSXE_WD-2-HEARTBEAT_FAIL

2-Critical

Heartbeat is not emitted. Heartbeat count:[dec]

Failure in IOS to generate a heartbeat is\n\ an abnormal condition

DDTS_COMPONENT

"This message may be related to an abnormal configuration\n\ and system load or transient high processing demand." "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative"

IOSXE_WD-2-HOG_DETECT_FAIL

2-Critical

CPUHOG detection failed to start.

Failure in setting up CPUHOG detection mechanism is\n\ an abnormal condition

DDTS_COMPONENT

"This message may be related to an abnormal configuration\n\ and system load or transient high processing demand." "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative"

CRPGC-0-REFERENCE_STUBBED

0-Emergency

stubbed [chars] is referenced

-

-

""

IOSXE_SCHED-3-CALLED_FROM_INT

3-Error

API call incorrectly made from interrupt level

-

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SCHED-3-NULLQ

3-Error

Invalid API parameter

An external routine provided by the ASR1000 scheduler was incorrectly called with an invalid NULL pointer.

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SCHED-3-AVL_INSERT_FAIL

3-Error

Could not insert pid [dec] into process tree

An avl_insert failed to add a process structure to the ASR1000

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SCHED-3-NEGATIVE_DEPTH

3-Error

Queue '[chars]' consumed more than it produced [dec]

-

-

-

IOSXE_SCHED-3-BACKOFF_PRODUCER

3-Error

Tx data in message queue '[chars]' appears to have stalled. Producer info: '[chars]' pid [dec] current queue depth: [dec] bytes

Based upon internal state derived from calls to mcp_queue_produced

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SCHED-3-CONTINUE_PRODUCER

3-Error

Stall for message queue '[chars]' have been cleared current queue depth: [dec] bytes

This is to inform that the condition for a message queue which had previously caused back-off of producer processs has been cleared

DDTS_COMPONENT

LOG_STD_ACTION

IOSXE_SPA-3-CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

Failed to create a SPA object.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-SPA_CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec].

Failed to create a SPA object.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-NULL_VFT

3-Error

[chars] virtual function table is not initialized. spaType=0x[hec]

A required function table is not initialized

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-NULL_VFUNC

3-Error

[chars] vector is not initialized. spaType=0x[hec]

A required function vector is not initialized

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-MEM_ALLOC_ERROR

3-Error

[chars]

Memory allocation error.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-NULL_BAY_PTR

3-Error

-

Pointer to SPA bay is NULL.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid slot number is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_SUBSLOT_NUM

3-Error

subslot= [dec] max subslot = [dec]

An invalid subslot number is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_DB_NUM

3-Error

db = [dec] max db = [dec] db intf = [dec] max db intf = [dec]

An invalid daughter board number is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_RP_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid RP slot number is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_CPU_NUM

3-Error

cpu= [dec] max cpu = [dec]

An invalid CPU number is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_SLOTUNIT_NUM

3-Error

cardwide-port = [dec] max cardwide-port = [dec]

An invalid cardwide-port number is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_INDX_RANGE

3-Error

index1= [dec] index2= [dec] maxIndex= [dec]

An invalid index range is specified in one of the internal APIs.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_IF_INDEX

3-Error

index= [dec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec]

Index for the interface is not valid.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_DATA_INSTANCE

3-Error

interface type [chars] slot [dec] port [dec] vc [dec] : [chars]

Data required to support the interface is not available.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-POWER_CYCLE

3-Error

[chars] occurred on Shared Port Adapter [dec]/[dec]

An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-DIAG_CONFIG

3-Error

[chars] did not complete [dec]/[dec]

An error has occured during diagnostic test.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-IPC_FAILURE

3-Error

IPC failure while [chars]

An error has occurred while prepareing or sending an IPC message.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-SENDCFGFAIL

3-Error

Failed to send configuration for [chars] to carrier-card for subslot=[dec]/[dec]

Sending configuration failed.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-CREATE_TDLH_FAILURE

3-Error

Failed to create SPA [dec]/[dec] handle

Failed to create message handle for SPA communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-DOMAIN_TDLH_FAILURE

3-Error

[chars] rc = [dec]

Failed to bind message handle for SPA communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-SETUP_TDLH_FAILURE

3-Error

Failed to set the alloc/free handler for SPA [dec]/[dec] handle

Failed to set the alloc/free handler for SPA communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-DISPATCH_INIT_TDLH_FAILURE

3-Error

Failed to initialize dispatch path for SPA [dec]/[dec] handle

Failed to initialize dispatch path handle for SPA communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_SPA_TDL_CCAPI_USAGE

3-Error

-

Incorrect usage of an internal API that should only be used on CC.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-6-TDLMSG_INCOMPATIBLE

6-Information

Failed to copy message [chars] to buffer not allowed for current domain.

Failure to marshal a message indicates an incompatibility with the intended recipient.

iosxe-spa-infra

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-CREATE_TDLMSG_FAILURE

3-Error

Failed to create [chars] message for [chars].

Failed to create/allocate necessary TDL message for SPA communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-3-INVALID_HANDLE

3-Error

Failed to get a valid IPC handle for type [dec] slot [dec] subslot [dec].

The client handle was found to be NULL for the given type/slot/subslot.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

IOSXE_SPA-6-UPDOWN

6-Information

Interface [chars] link down due to [chars]

Ethernet link is down due to remote/local fault.

DDTS_COMPONENT

"Replace the faulty cable."

IOSXE_SPA-6-DUAL_RATE_CHANGE

6-Information

[chars]: [chars]

Change in rate of the link.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_SPA-3-SPA_SETUP_FAILURE

3-Error

Failed to properly setup for SPA communication on slot [dec] subslot [dec].

Discovery of the linux interface used to communicate with a SPA failed

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

UEA_INFO-3-MAX_TDM_PW_PER_PORT_EXCEEDED

3-Error

TDM PWs configured on SPA[chars] Interface [chars]

Number of TDMoMPLS intd labels exceeded supported scale

-

"Please reduce the number of TDM PW's per Port to supported scale"

UEA_INFO-3-MAX_TDM_PW_PER_IM_EXCEEDED

3-Error

TDM PWs configured on SPA[chars] subslot [dec]/[dec] exceeds

Number of TDMoMPLS intd labels exceeded supported scale

-

"Please reduce the number of TDM PW's per Port to supported scale"

IOSXE_SPA-3-ABANDON_SPA_CONFIGURATION

3-Error

Abandon configuration for subslot [dec]/[dec] the SPA type[dec] is NOT match

Abandon SPA configuration.

DDTS_COMPONENT

"Please check the startup configuration use \"no " "card\" command to override wrong card configuration and update card " "type."

IOSXE_SPA-4-COMMUNICATION_ESTABLISHED

4-Warning

Communication with IM in [dec]/[dec] restored.

IPC communication between IOS and specified IM has been restored.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_SPA-4-COMMUNICATION_DISCONNECTED

4-Warning

Communication with IM in [dec]/[dec] stalled. Retrying. IM will reboot if situation persists

Retransmit IPC communication request between IOS and IOMD.

DDTS_COMPONENT

LOG_STD_NO_ACTION

IOSXE_SYS_INFRA-6-BIPC_READ_ERR

6-Information

connection read error from [chars] rc [dec] bring down IPC id [dec] for fd [dec] seq [dec]

BIPC error during IPC read

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-BIPC_READBUF_ERR

6-Information

process receive buffer error from [chars] rc [dec] bring down IPC

BIPC error during IPC read from buffer

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-BIPC_DISCONNECT

6-Information

disconnect by application for [chars] bring down IPC

BIPC disconnect requested by an application

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-BIPC_WRITE_ERR

6-Information

write bipc error for [chars] rc [dec] bring down IPC

BIPC error during IPC read

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-BIPC_CREATE

6-Information

bipc connect succeeded for [chars] ipc_ctl_id [dec] ipc_fd [dec] seq [dec]

BIPC connect succeeded

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-BIPC_CREATE_FAIL

3-Error

Failed to open IPC port '[chars]' for service '[chars]' with error [chars].

BIPC connect failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-BIPC_DISCONNECT_FAIL

3-Error

Failed to disconnect IPC port '[chars]' for service '[chars]' with error [chars].

BIPC disconnect failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-4-BIPC_TX_Q_THRESHOLD

4-Warning

BIPC transmit queue threshold reached for the channel '[chars]':\n\ ipc_ctl_id [dec] ipc_fd [dec] seq_num [dec] Tx Q size [dec]

-

-

-

IOSXE_SYS_INFRA-4-BIPC_RX_IN_APPL_THRESHOLD

4-Warning

Number of IPC messages held in the application reached the \n\ maximum channel threshold. IPC channel '[chars]': \n\ ipc_ctl_id [dec] ipc_fd [dec] seq_num [dec] curr IPC msg hel in appl [dec]

-

-

-

IOSXE_SYS_INFRA-3-EVLIB_EPOLL_ARGS

3-Error

evGetEpollArgs returned fd [dec]

Evlib retuned a huge FD value that IOS can not handle.

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-EOBC_ADDR_CACHE

6-Information

EOBC ip-table cache: [chars]

Unable to setup internal address for eobc communication

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EOBC_SOCK

3-Error

Socket event for [chars]

An internal socket level event has returned an error which\n\ is indicated. This may have been the result of a bind\n\ peek receive or send operation with respect to the EOBC\n\ interface listed.

iosxe-iosd-infra

"show eobc\n\ show platform software\n\ infrastructure bipc"

IOSXE_USB-3-ESHOW_USB

3-Error

Internal Error locating database for USB Devices.

The mcp_usb_devices is incorrect and needs to be changed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EWRITE_EVENT_FD

3-Error

Write to [chars] wakeup fd failed errno [dec] current signal/wakeup cnt: %llu/%llu

Trigering a thread by writing to its wakeup fd failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EREAD_EVENT_FD

3-Error

[chars] read from wakeup fd failed errno [dec]

A thread reading from its wakeup fd failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EIOS_POLL

3-Error

IOS thread poll on event lib and wakeup fds failed errno [dec]

IOS thread poll on event lib and wakeup fds failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EIOS_EVDISPATCH

3-Error

IOS scheduler event dispatch failed ev_ret [dec] errno [dec]

IOS scheduler event dispatch failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EIOS_EVGETNEXT

3-Error

IOS scheduler get next event failed ev_ret [dec] errno [dec]

IOS scheduler get next event failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EFP_EVDISPATCH

3-Error

Fastpath thread event dispatch failed ev_ret [dec] errno [dec]

fastpath thread event dispatch failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EFP_EVGETNEXT

3-Error

Fastpath thread get next event failed ev_ret [dec] errno [dec]

Fastpath thread get next event failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EFP_EPOLL_WAIT

3-Error

Fastpath thread epoll wait failed errno [dec]

Fastpath epoll wait failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EFP_TOP_EPOLL_CTL_FAILED

3-Error

Fastpath thread top level efd epoll [chars] failed fd [dec] errno [dec]

Fastpath top level efd epoll_ctl operation failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EFP_IPC_EPOLL_CTL_FAILED

3-Error

Fastpath thread [chars] [chars] for IPC channel [chars] ipc id [dec] ipc fd [dec] seqnum [dec] failed efd [dec] errno [dec]

Fastpath epoll_ctl operation for an IPC channel failed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-3-EFP_IPC_EPOLL_NO_IPC_ENTRY

3-Error

IPC entry not found for ipc fd [dec] seq [dec] events 0x[hec] while processing [chars] from epoll fd [dec]

Fastpath failed to find IPC entry after epoll_wait

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-FP_IPC_DISCONNECT

6-Information

IPC channel disconnect for [chars] ipc_ctl_id [dec] fd [dec] seq_num [dec] loc [chars] err [dec] [chars]

An IPC channel in fastpath is terminated

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-IOS_IPC_CTL_DESTROY

6-Information

IPC control blk destroy: name [chars] ipc_ctl_id [dec] refcout [dec] need_free [dec]

An IPC control block is requested to be destroyed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-6-IOS_FREE_IPC_CTL

6-Information

IPC control blk free: name [chars] ipc_ctl_id [dec] refcount [dec]

An IPC control block is freed

iosxe-iosd-infra

LOG_STD_ACTION

IOSXE_SYS_INFRA-4-BIPC_CLEAR_CONN

4-Warning

IPC channel fd [dec] seq_num [dec] for service '[chars]' cleared by user

BIPC disconnect requested by an user with clear command

iosxe-iosd-infra

LOG_STD_ACTION

DB_NTFY_MGR-3-INITFAIL

3-Error

Initialization of the Database Notification Manager facility failed [chars].

An unexpected condition has occurred which resulted in the Database notification manager facility failing to start. This is a serious problem and means that the Database notification manager facility will not be functional.

crimson

LOG_STD_ACTION

DB_NTFY_MGR-3-REQPROCFAIL

3-Error

Database Notification Manager Request Processing facility failed [chars].

An unexpected condition has occurred which resulted in the Database notification manager facility failing to process a request. This means that some part of Database notification manager facility will not be functional.

crimson

LOG_STD_ACTION

NGMOD_OBFL-5-DISABLED

5-Notice

[chars] Onboard Failure Logging disabled on slot [dec]

SWC Sensor Registration failed!

-

"This message is for informational purposes only"

IMSP_IPSG-3-IPSG_ADDRS_FULL

3-Error

IPSG Platform Address list is null

An unexpected condition has occurred which is due to the absence of\n\ resource available in IPSG address list

l2security

"Correct the config which can have max of 254 IP address"

IDWL-3-LOOP_BACK_DETECTED

3-Error

Loop-back detected on [chars].

Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network.

firmware

"Correct the problem causing the loopback " "condition. Then bring the port up by entering the shutdown " "then no shutdown interface configuration commands."

IOSXE_IMSP_ADJ-3-NOADJ

3-Error

Adjacency entry is null

An unexpected condition has occurred which is due to the absence of\n\ an adjacency entry structure.

iosxe-fwdmgr

"show adjacency"

IOSXE_IMSP_ADJ-3-NOFIBHWIDB

3-Error

FIB Interface [chars] is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure.

iosxe-fwdmgr

"show adj"

IOSXE_IMSP_ADJ-3-ENQUEFAIL

3-Error

Unable to send [chars] [chars] message to Forwarding Manager Process

An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs.

iosxe-fwdmgr

LOG_STD_ACTION

IOSXE_IMSP_ADJ-3-ENCSIZE

3-Error

Invalid encap length [dec] which is larger than max allowed [dec] bytes

An unexpected condition has occurred which is due to invalid\n\ adjacency encapsulation size being larger than the maximum value\n\ allowed.

iosxe-fwdmgr

LOG_STD_ACTION

PETRA_IMSP_CEF-3-NOFIB

3-Error

FIB entry is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB entry structure.

petra-fwdmgr

"show ip cef"

PETRA_IMSP_CEF-3-NOFIBSB

3-Error

FIB SB entry is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB SB entry structure.

petra-fwdmgr

"show ip cef"

PETRA_IMSP_CEF-3-NOFIBTABLE

3-Error

FIB table is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB table structure.

petra-fwdmgr

"show ip cef"

PETRA_IMSP_CEF-3-NOFIBIDB

3-Error

FIB interface is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure.

petra-fwdmgr

"show ip cef"

PETRA_IMSP_CEF-4-UPDSTATSERR

4-Warning

Update CEF statistics error

An unexpected condition has occurred when updating cef statistics

petra-fwdmgr

LOG_STD_ACTION

PETRA_IMSP_CEF-3-NOFIBPUSHCNT

3-Error

FIB push counter is null

An unexpected condition has occurred which is due to the absence of\n\ a FIB push counter structure.

petra-fwdmgr

"show ip cef"

IMSP_ACLMGR-2-NOVMR

2-Critical

Cannot generate hardware representation of access list [chars]

There were insufficient resources available for generating a hardware representation of the access list. Either lack of available logical operation units or lack of memory can cause this problem. Logical operation units are needed when a match on TCP flags is specified or when any test other than eq that is: ne gt lt or range is

firmware

"Modify the ACL configuration to use fewer resources."

IMSP_ACLMGR-4-ACLTCAMFULL

4-Warning

[chars]ACL TCAM Full. Software Forwarding packets on

The ACL configuration is too large to fit in the platform -specific ACL TCAM table.

firmware

"Simplify the ACLs applied to interfaces or reduce" " their number."

IMSP_ACLMGR-3-UNKNOWNACTION

3-Error

Unknown VMR access group action 0x[hec]

An internal software error has occurred.

firmware

LOG_STD_ACTION

IMSP_ACLMGR-3-UNKNOWNL4OPERATION

3-Error

Unknown L4 operation 0x[hec]

ACL Manager module received invalid value for L4 operation. The problem can be due to memory corruption or bad system memory.

firmware

IMSP_ACL_L4OP_ERROR

IMSP_ACLMGR-3-INVALIDPARAM

3-Error

Invalid [chars] [dec] encountered

ACL Manager has encountered an invalid parameter value.

firmware

"show running-config"

IMSP_ACLMGR-3-MAXACE

3-Error

MAX ACE count [dec] exceeded

No. ACEs configured is beyond limit

imsp-acls

LOG_STD_ACTION

IMSP_ACLMGR-2-NOMEM

2-Critical

[chars]. Out of memory

System is out of Memory

imsp-acl

LOG_STD_ACTION

IMSP_ACLMGR-3-INVALIDACL

3-Error

[chars] failed

Addition/Deletion Failed

imsp-acl

LOG_STD_ACTION

IMSP_CTS-3-SGT_PROGRAM_ERR

3-Error

[chars] binding [chars] failed for [chars] with reason [chars]\n

An unexpected condition has occurred while programming IP SGT

-

"Reconfigure the IP SGT binding"

IMSP_CTS-6-SGT_TABLE_FULL

6-Information

Platform can not support more than [dec] [chars] bindings

IP/SUBNET SGT table resource full

-

"Remove SGT binding\n"

IMSP_CTS-6-SGACL_POLICIES

6-Information

Platform can not support more than [dec] ACEs per cell.

SGACL policy entries limit exceeded

-

"Remove one or more entries from ACES\n"

IMSP_CTS-6-INVALID_ACE

6-Information

Platform can suppor match only ip protocol tcp/udp src or dst port

Invalid match criteria

-

"Remove one or more entries from ACES\n"

IMSP_CTS-6-SGACL_TABLE_FULL

6-Information

Platform can not support more than [dec] SGT/DGT pairs

SGACL table resource full

-

"Remove SGACL\n"

IMSP_CTS-3-SGACL_PROGRAM_ERR

3-Error

Unable to [chars] SGACLs for sgt [dec] dgt [dec] with reason [chars]

An unexpected condition has occurred while programming SGACL

petra-cts

"Reconfigure the SGACL"

IMSP_EPM-3-EPM_ACE_MAX_CROSS

3-Error

EPM - Reached max ace limit255

An unexpected condition has occurred since max ACE limit reached

l2security

"Correct the config which can have max of 255 ACEs\ per port"

IE3X00_LICENSE-4-FEAT_OOC

4-Warning

Feature [chars] Out Of Compliance Existing feature configurations would be disabled on net reboot

Smart License Agent enforcement mode changed to out of compliance

-

"Report to TAC and add sufficient licenses"

IE3X00_LICENSE-5-FEAT_IN_COMPLIANCE

5-Notice

Feature [chars] is Authorized

Smart License Agent enforcement mode changed to Incompliance

-

"None"

IE3X00_LICENSE-5-FEAT_EVAL_MODE

5-Notice

Feature [chars] is operating in Eval Mode

Smart License Agent enforcement mode changed to EVAL MODE

-

"None"

IE3X00_LICENSE-4-FEAT_EVAL_EXPIRED

4-Warning

Evaluation Period Expired for [chars]

Eval Period has expired. License agent moving to eval-expired state

-

"Restore communication with cisco and register " " the device"

PLATFORM_IMSP-3-PORT_NOT_OPERATING

3-Error

[chars] [chars] [chars] [chars]

The port is not operating the startup selftest has failed

-

LOG_STD_ACTION

PLATFORM_IMSP-3-PORT_NOT_FORWARDING

3-Error

[chars] [chars] [chars] [chars]

The port is not forwarding the startup selftest has failed

-

LOG_STD_ACTION

PLATFORM_IMSP-3-FCS_ERROR

3-Error

[chars] [chars] [chars] [chars]

The port fcs error threshold max has reached

-

LOG_STD_ACTION

PLATFORM_IMSP-3-PORT_LINK_FAULT

3-Error

[chars] [chars] [chars] [chars]

The port link is not coming up the startup selftest has failed

-

LOG_STD_ACTION

PLATFORM_IMSP-5-PORT_FAST_RETRAIN

5-Notice

Port link fast-retraining has happened for [chars]

The port link fast-retraining has happened for [chars]

-

LOG_STD_NO_ACTION

PLATFORM_IMSP-5-PORT_SEU_EVENT

5-Notice

Port SEU Cable discharge event on [chars]. Firmware Download in progress.

Port SEU Cable discharge event on [chars]. Firmware download in progress.

-

LOG_STD_NO_ACTION

PLATFORM_IMSP-5-PORT_SEU_EVENT_FW_DWLD_SUCCESS

5-Notice

Port SEU Cable discharge event on [chars]. Firmware download successful.

Port SEU Cable discharge event on [chars]. Firmware download successful.

-

LOG_STD_NO_ACTION

PLATFORM_IMSP-5-PORT_SEU_EVENT_FW_DWLD_FAIL

5-Notice

Port SEU Cable discharge event on [chars]. Firmware download failed.

Port SEU Cable discharge event on [chars]. Firmware download failed.

-

LOG_STD_NO_ACTION

ENVIRONMENT-4-SECONDARY_UNDERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the configured min temperature \n\ threshold but less or equal to the max inside temperature

-

-

ENVIRONMENT-4-SECONDARY_OVERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the configured threshold\n\ but less or equal to the max inside temperature

-

-

ENVIRONMENT-3-OVERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the max temperature threshold

-

-

ENVIRONMENT-3-UNDERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the min temperature threshold

-

-

ENVIRONMENT-3-RPS_FAILED

3-Error

[chars] [chars] [chars] [chars]

Only one power supply was detected for system in dual power mode or\n\ power supply is failing

-

-

ENVIRONMENT-3-SD_CARD

3-Error

[chars] [chars] [chars] [chars]

SD card is not present

-

-

ENVIRONMENT-3-SD_CARD_UNSUPPORTED

3-Error

[chars] [chars] [chars] [chars]

SD card is not supported

-

-

ENVIRONMENT-3-SD_CARD_CORRUPT

3-Error

[chars] [chars] [chars] [chars]

SD card is corrupted

-

-

ENVIRONMENT-3-SD_CARD_FILES_CORRUPT

3-Error

[chars] [chars] [chars] [chars]

Image File on SD card is corrupted

-

-

ENVIRONMENT-3-SD_CARD_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

SD card is not present. Image booted from on-board flash.

-

-

ENVIRONMENT-3-SD_CARD_UNSUPPORTED_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

SD card is not supported. Image booted from on-board flash.

-

-

ENVIRONMENT-3-SD_CARD_CORRUPT_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

SD card is corrupted. Image booted from on-board flash.

-

-

ENVIRONMENT-3-SD_CARD_FILES_CORRUPT_BOOTFLASH

3-Error

[chars] [chars] [chars] [chars]

Image File on SD card is corrupted. Image booted from on-board flash.

-

-

ENVIRONMENT-3-LIC_FILE_CORRUPT

3-Error

[chars] [chars] [chars] [chars]

License file is corrupted

-

-

ENVIRONMENT-3-AC1_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 1 triggered

-

-

ENVIRONMENT-3-AC2_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 2 triggered

-

-

ENVIRONMENT-3-AC3_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 3 triggered

-

-

ENVIRONMENT-3-AC4_TRIGGER

3-Error

[chars] [chars] [chars] [chars]

External Alarm Contact 4 triggered

-

-

ENVIRONMENT-2-PS_A_HIGHVOLTAGE

2-Critical

[chars] [chars] [chars] [chars]

Power supply input voltage exceeding threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over voltage."

ENVIRONMENT-2-PS_A_LOWVOLTAGE

2-Critical

[chars] [chars] [chars] [chars]

Power supply input voltage is below low threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by low voltage."

ENVIRONMENT-2-PS_B_HIGHVOLTAGE

2-Critical

[chars] [chars] [chars] [chars]

Power supply input voltage exceeding threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by over voltage."

ENVIRONMENT-2-PS_B_LOWVOLTAGE

2-Critical

[chars] [chars] [chars] [chars]

Power supply input voltage is below low threshold

cgs2520

"Please save system configuration and power down system" "to prevent damage causes by low voltage."

ENVIRONMENT-3-POWER_ERROR

3-Error

[chars]

Power supply error.

-

" Make sure that the power supply connected are supported." " If the problem still persists then please contact TAC."

PLATFORM_ENV-1-EXTERNAL_ALARM_CONTACT_ASSERT

1-Alert

Alarm asserted: [chars]

Error condition detected on external alarm contact

hardware

LOG_STD_ACTION

PLATFORM_ENV-1-EXTERNAL_ALARM_CONTACT_CLEAR

1-Alert

Alarm cleared: [chars]

Error condition cleared on external alarm contact

hardware

LOG_STD_ACTION

POWER_SUPPLIES-3-PWR_A_FAIL

3-Error

Power supply A is not functioning

Power supply A is present but not functioning

hardware

LOG_STD_ACTION

POWER_SUPPLIES-3-PWR_B_FAIL

3-Error

Power supply B is not functioning

Power supply B is present but not functioning

hardware

LOG_STD_ACTION

POWER_SUPPLIES-5-PWR_A_OK

5-Notice

Power supply A is functioning

Power supply A is supplying power

hardware

LOG_STD_NO_ACTION

POWER_SUPPLIES-5-PWR_B_OK

5-Notice

Power supply B is functioning

Power supply B is supplying power

hardware

LOG_STD_NO_ACTION

POWER_SUPPLIES-3-PWR_FAIL

3-Error

Power supply [chars] is not functioning

Power supply is present but not functioning

hardware

LOG_STD_ACTION

POWER_SUPPLIES-5-PWR_OK

5-Notice

Power supply [chars] is functioning

Power supply is supplying power

hardware

LOG_STD_NO_ACTION

PLATFORM-5-TRANSCEIVERREMOVED

5-Notice

Slot=[dec] Port=[dec]: Transceiver has been removed

-

-

-

PLATFORM-5-TRANSCEIVERINSERTED

5-Notice

Slot=[dec] Port=[dec]: Transceiver has been inserted

-

-

-

PLATFORM-5-TRANSCEIVER_CHECKSUMFAILED

5-Notice

Slot=[dec] Port=[dec]: SFP EEPROM data check sum failed

The SFP was identified as a Cisco SFP but the system was unable to read vendor-data information to verify its correctness.

petra-platform

"Remove and reinsert the SFP. If it fails " "again in the same way the SFP may be defective."

PLATFORM-5-TRANSCEIVER_SECURITYCHECKFAIL

5-Notice

Slot=[dec] Port=[dec]: SFP Security check failed

-

-

-

PLATFORM-5-TRANSCEIVER_UNSUPPORTED_SYS

5-Notice

Slot=[dec] Port=[dec]: Unsupported transceiver for the switch found

This SFP type is not supported on this switch.

petra-platform

LOG_STD_ACTION

PLATFORM-5-TRANSCEIVER_UNSUPPORTED_PORT

5-Notice

Slot=[dec] Port=[dec]: Unsupported transceiver for the port found

This SFP type is not supported on this port.

petra-platform

LOG_STD_ACTION

PLATFORM-5-TRANSCEIVER_UNSUPPORTED

5-Notice

Slot=[dec] Port=[dec]: Unsupported transceiver found

The module was identified as an unsupported non-Cisco transceiver.

petra-platform

LOG_STD_ACTION

PLATFORM-5-HALF_DUPLEX

5-Notice

half duplex operation discovered on [chars] with [chars] [chars]

The interface is found to operate in half duplex

petra-platform

LOG_STD_ACTION

SUDI-5-VALIDATION_SUCCESS

5-Notice

[chars]

-

-

-

SUDI-5-VALIDATION_CHECK

5-Notice

[chars]

-

-

-

SUDI-1-VALIDATION_ERROR

1-Alert

[chars]

[chars] Secure UDI validation failed.

petra-platform

"If this occurs the switch failed to authenticate itself. " "Please contact Cisco's Technical Assistance Center for more " "information."

SUDI-1-INTERNAL_ERROR

1-Alert

[chars]

Secure UDI encountered an internal error.

petra-platform

"If this occurs the switch failed to authenticate itself. " "Please contact Cisco's Technical Assistance Center for more " "information."

PLATFORM-4-MATM_TBL_OVERFLOW

4-Warning

Mac table has reached the maximum limit.Features dependent on Mac table may have an impact.

Mac Table is full and no space available for new mac address addition. MATM learning and dependent feature functionality may be impacted.

petra-l2

"Make some space available in Mac Table" " to restore mac learning functions."

MRP-3-RINGERROR

3-Error

Miscabling detected Port [chars] does not belong to the MRP ring [dec].

The MRP ring is in FAULT state. This happens when a cable is wrongly connected on another ring

petra-mrp

"Check the wiring and re-connect the cables again. " "Enable recovery of the err-disabled port using" "'errdisable recovery cause mrp-miscabling'."

HSR_ALARM-2-HSR_RINGFAULT

2-Critical

The HSR ring is now in FAULT state

HSR Ring Down: The HSR ring is in FAULT state. This typically happens when both ring ports are down because of link or node failure.

-

-

HSR_ALARM-3-HSR_PARTIALFAULT

3-Error

The HSR ring is now in PARTIAL FAULT state

HSR Port Down: The HSR ring is in PARTIAL FAULT state. This typically happens when one of the ring port is down because of link or node failure. The Ring is still functional but needs attention as it can not handle further faults.

petra-hsr

-

PRP_MSG-4-PRP_VLANTAG

4-Warning

Warning: Please do not configure access mode for PRP interfaces with tagged supervision frames

Supervision frames will be tagged with vlan id after user configured vlan tag and vlan id access mode will cause confliction on traffic

petra-prp

-

DECLASSIFICATION-3-UNABLE_TO_RESET_CONFIG

3-Error

[chars]

The system is unable to reset the configuration

firmware

LOG_STD_ACTION

DECLASSIFICATION-5-CONFIG_IS_RESET

5-Notice

[chars]

The configuration is reset and the system will now reboot

firmware

LOG_STD_ACTION

CBR_PTP-5-TOD_CHG

5-Notice

The TOD source changed: [chars]

The source of time of day changed: 1. from GPS of SUP-PIC 0/1 2. from DTI of SUP-PIC 0/1 3. free run mode

cbr-ptp

LOG_STD_NO_ACTION

CBR_PTP-3-NITFAIL

3-Error

Failed to initalize required PTP resource: [chars]

During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated.

cbr-ptp

LOG_STD_ACTION

CBR_PTP-3-INITFAIL

3-Error

Failed to initalize required PTP resource: [chars]

During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated.

cbr-ptp

LOG_STD_ACTION

CBR_PTP-3-DISPATCH

3-Error

Unable to dispatch received TDL message from PTP daemon

This is an Event from RPD

cbr-ptp

LOG_STD_NO_ACTION

IOSXE_SIP_SPA-3-IPCPORTFAIL

3-Error

Failed to open IPC port '[chars]' [chars] with error [chars]

The RP failed to open a port for communication with a SPA\n\ module.

asr1k-spa-infra

LOG_STD_ACTION

IOSXE_SIP_SPA-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The Linecard failed to send a message to the\n\ Route Processor ASR1000-RP.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOSXE_SIP_SPA-3-IPCPORT

3-Error

Failed to [chars] IPC port '[chars]' error [chars]

The Linecard failed to create a port for\n\ communication with the Route Processor ASR1000-RP.

asr1k-spa-infra

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CSMPI-3- PLATFORM_INIT_FAILED

3-Error

CSMPI platform initialization failed.

Essential CSMPI initialization has failed.

-

LOG_STD_ACTION

CSMPI-3- IF_INIT_FAILED

3-Error

CSMPI interface initialization failed.

Essential CSMPI initialization has failed.

-

LOG_STD_ACTION

CSMPI-3- ADDR_MISMATCH

3-Error

Region address error: start @ %p end @ %p part addr @ %p

CSMPI encountered a bnad buffer address possible corruption.

-

LOG_STD_ACTION

CSMPI-3- BAD_INDEX

3-Error

bad particle index [dec] max [dec] addr %p

CSMPI encountered a bnad buffer address possible corruption.

-

LOG_STD_ACTION

CMANCC-3-MSGDISPATCH

3-Error

Unable to dispatch received message from Chassis Manager

An unexpected condition has occurred while IOS was trying to dispatch\n\ a message received from the Chassis Manager.

iosxe-chassismgr

"Verify that all local components are in the proper operational state.\n\ If any inconsistency is found it may be corrected by offlinine and\n\ restart of the effected component SPA Carrier Card"

CMANCC-3-MSGIPCERR

3-Error

Unable to process received IPC messages from Chassis Manager\n\ error: [chars]

An unexpected condition has occurred while IOS trying to process a\n\ received IPC message from Chassis Manager.

iosxe-chassismgr

LOG_STD_ACTION

CMANCC-2-CRASHDUMP

2-Critical

Fatal error calling crashdump error: [dec] [chars]

A fatal condition has occurred causing IOS to crashdump. IOS will\n\ be restarted automatically.

iosxe-chassismgr

LOG_STD_ACTION

CMANCC-3-UNEXPECTEDEVENT

3-Error

UDI Auth Process received unknown event maj [hec] min [hec].

UDI auth process has registered to be notified when a process \n\ boolean change event occurs in the router. This message indicates \n\ that this process received an event it did not know how to handle.

iosxe-chassismgr

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

ASR903_CFC-4-PUNT_KEEPALIVE_ERR_INV_PARAM

4-Warning

Invalid parameter: [chars]

Invalid parameter was passed when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-4-PUNT_KEEPALIVE_ERR_GET_FILE_NAME

4-Warning

Failed to get file name

Could not form a file name when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-4-PUNT_KEEPALIVE_ERR_INV_FILE_ID

4-Warning

Invalid file descriptor: [dec]

Invalid file descriptor was found when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-3-PUNT_KEEPALIVE_ERR_OPEN_FILE

3-Error

Failed to open file: [chars]

Failed to open file when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-4-PUNT_KEEPALIVE_ERR_CLOSE_FILE

4-Warning

Failed to close file with descriptor: [dec]

Closing of file failed when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-3-PUNT_KEEPALIVE_ERR_WRITE_TO_FILE

3-Error

Write to file Id [dec] failed [dec] bytes expected [dec] bytes

Write to file failed when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-3-PUNT_KEEPALIVE_ERR_ALLOC_TTY

3-Error

Failed to allocate a tty

Can't allocate a TTY when generating punt err log

asr903-cfc

LOG_STD_ACTION

ASR903_CFC-3-PUNT_KEEPALIVE_ERR_ALLOC_CSB

3-Error

Failed to allocate a csb

Can't allocate a csb when generating punt err log

asr903-cfc

LOG_STD_ACTION

NCS4206_CFC-4-PUNT_KEEPALIVE_ERR_INV_PARAM

4-Warning

Invalid parameter: [chars]

Invalid parameter was passed when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-4-PUNT_KEEPALIVE_ERR_GET_FILE_NAME

4-Warning

Failed to get file name

Could not form a file name when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-4-PUNT_KEEPALIVE_ERR_INV_FILE_ID

4-Warning

Invalid file descriptor: [dec]

Invalid file descriptor was found when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-3-PUNT_KEEPALIVE_ERR_OPEN_FILE

3-Error

Failed to open file: [chars]

Failed to open file when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-4-PUNT_KEEPALIVE_ERR_CLOSE_FILE

4-Warning

Failed to close file with descriptor: [dec]

Closing of file failed when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-3-PUNT_KEEPALIVE_ERR_WRITE_TO_FILE

3-Error

Write to file Id [dec] failed [dec] bytes expected [dec] bytes

Write to file failed when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-3-PUNT_KEEPALIVE_ERR_ALLOC_TTY

3-Error

Failed to allocate a tty

Can't allocate a TTY when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

NCS4206_CFC-3-PUNT_KEEPALIVE_ERR_ALLOC_CSB

3-Error

Failed to allocate a csb

Can't allocate a csb when generating punt err log

ncs4206-cfc

LOG_STD_ACTION

LOTR_DBG-3-LOTR_RSRS_HA_ERR

3-Error

[chars]

Resource dynamically allocated are synced to standby.\ Due to error mentioned sync failed.\n\ So standby won't be having same database as active

asr900-tdm-combo

-

LOTR_DBG-6-LOTR_RSRS_HA_INFO

6-Information

[chars]

Cem programming completed

asr900-tdm-combo

-

LOTR_DBG-4-LOTR_RSRS_HA_WARNING

4-Warning

[chars]

Cem programming is not completed

asr900-tdm-combo

LOTR_RSRS_HA_INTERNAL_SW_WARNING_ACTION

UEA_PTP_ENABLER-3-UEA_PTP_LICENSE_EULA_NOT_ACCEPTED

3-Error

\n********************************************************* \ \nWARNING: PTP License is not yet activated. \ \nPlease configure 'license feature ptp'\ \n*********************************************************\n

-

-

LOG_STD_ACTION

PLT_DBG_SCRIPTS-3-DIR_FAIL

3-Error

Failed to create [chars] directory in [chars] filesystem with [chars] error

Failed to create platform_debug_scripts directory\n\ bootflash

asr900-layer2-rsp3

"Ensure bootflash has sufficient space\n\ verify integrity of the bootflash"

PLT_DBG_SCRIPTS-3-FILE_FAIL

3-Error

Failed to create [chars] file with [chars] error

Failed to create platform_debug_scripts file\n\ bootflash

asr900-layer2-rsp3

"Ensure bootflash has sufficient space\n\ verify integrity of the bootflash"

PLT_DBG_SCRIPTS-3-WRITE_FAIL

3-Error

Failed to write [dec] bytes in [chars] file

Failed to write data into the tcl debug script file

asr900-layer2-rsp3

"Ensure bootflash has sufficient space\n\ verify integrity of the bootflash"

PLT_DBG_SCRIPTS-3-INVALID_IDB

3-Error

Retrieved IDB from parser is invalid

Failed to write data into the tcl debug script file

asr900-layer2-rsp3

"Contact Cisco TAC\n"

MAT_LIMIT-4-EXCEEDED

4-Warning

bdomain [dec] with configured limit %ld has currently %ld entries

The Number of mac entries for a bdomain has exceeded the\n\ allowed number

l2

"Depends of the Network admin"

MAT_LIMIT-4-DROPPED

4-Warning

bdomain [dec] with configured limit %ld has currently %ld entries

The Number of mac entries for a bdomain has gone below or\n\ is equal to the allowed number

l2

"Depends of the Network admin"

ASR900_PTP-3-MSGINITFAIL

3-Error

Failed to initalize required PTP resource: [chars]

During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated.

asr900-ptp

LOG_STD_ACTION

ASR900_PTP-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message from PTP daemon

An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from PTP daemon.

asr900-ptp

LOG_STD_ACTION

NCS4200_PTP-3-MSGINITFAIL

3-Error

Failed to initalize required PTP resource: [chars]

During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated.

ncs4200-ptp

LOG_STD_ACTION

NCS4200_PTP-3-MSGDISPATCH

3-Error

Unable to dispatch received TDL message from PTP daemon

An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from PTP daemon.

ncs4200-ptp

LOG_STD_ACTION

UEA_IPSEC_LIC-3-ENABLE_REBOOT_REQUIRED

3-Error

Reboot is required to enable IPSec license. Use 'write' command to make 'license feature ipsec' available after reboot.

UEA IPsec license enable will take effect on next reboot

uea_ipsec

LOG_STD_NO_ACTION

UEA_IPSEC_LIC-3-DISABLE_REBOOT_REQUIRED

3-Error

Reboot is required to disable IPSec license. Use 'write' command to make 'no license feature ipsec' available after reboot.

UEA IPsec license disable will take effect on next reboot

uea_ipsec

LOG_STD_NO_ACTION

UEA_IPSEC_LIC-3-NPE_IMAGE

3-Error

This command is not supported in an NPE image

IPsec license cannot be enabled/disabled in an NPE image!

uea_ipsec

LOG_STD_NO_ACTION

UEA_IPSEC_LIC-3-UNAVAILABLE_RESOURCES

3-Error

Some system resources are not available due to incorrect IPsec license configuration. Please reboot for proper functioning of the system

Some system resources were reserved at bootup for IPsec feature due to incorrect IPsec license configuration. Reboot is needed to resolve this problem.

uea_ipsec

LOG_STD_NO_ACTION

RP_MLP-4-BADLINKDECONFIG

4-Warning

Bad way of removing member link now perform 'no shut' on both sides of Multilink

If member link has to be removed from multilink bundle first\n\ remove the multilink configuration from the member link and\n\ then perform no channel-group command on the controller.

uea-im-tdm

"If the member link is removed from the multilink bundle using\n\ "no channel-group" command perform "no shut" on both sides\n\ of the multilink interface to make it work."

RP_MLP-6-BAYMISMATCH

6-Information

Bay number in message [dec] received [chars] greater than max number [dec]

Bay number in the message received exceeded max number of bays

uea-im-tdm

LOG_STD_RECUR_ACTION

RP_MLP-6-INCOMPATIBLE_LINK_ADD

6-Information

Link [chars] added to [chars] belongs to a different bay

Links added to the bundle must all belong to the same bay

uea-im-tdm

LOG_STD_RECUR_ACTION

RP_MLP-3-UNSUPPORTEDCONFIG

3-Error

The current config cannot be supported as [chars] for [chars]

When using multilink 1 The maximum number of links in the bundle and number of bundles

uea-im-tdm

" Please modify the config as not to violate the restrictions"

RP_MLP-5-SPAWARNING

5-Notice

could not add link for bundle [chars] as [chars]

A link was added to the bundle but it is not on the same bay as other member links of the bundle.

-

"Ensure that when a link is added to a bundle " "that it is on the same bay as the other member " "links of the bundle in order to have the MLP "

RP_MLP-3-INCOMPATIBLELINK

3-Error

The current config cannot be supported as link[chars] [chars] for bundle [chars]

When using multilink 1 All the links should be from the same port.

uea-im-tdm

" Please modify the config as not to violate the restrictions"

RP_MLP-5-SLOTMISMATCH

5-Notice

Link[chars] cannot be added to Bundle[chars] as [chars]

Link should be on same slot as other member links of Bundle.

-

""

RP_MLP-5-LINKTYPEMISMATCH

5-Notice

Link[chars] cannot be added to Bundle[chars]

Link speed mismatch with other member links of the bundle.

-

""

RP_MLP-3-CFG_FAILED

3-Error

Config send to IM failed reason[dec]

Configuration send to IM failed

uea-im-tdm

""

ASR900_PLATFORM-3-BP_AUTH_FAIL

3-Error

Failed to Authenticate the backplane quack deivice. This device may not be a quacked properly or not CISCO manufactured.

During the router boot-up we check if this router is cisco manufactured or not. If this device is not quacked properly or not CISCO manufactured this error is expected.

asr900-csl

LOG_STD_ACTION

ASR900_PLATFORM-3-PUNT_KEEPALIVE_PROP_SET_ERR

3-Error

Failed to set chasfs property [chars] with [chars] rc=[dec]

Failure occured while updating chasfs property

asr900-system-rsp3

LOG_STD_ACTION

ASR900_PLATFORM-3-PUNT_KEEPALIVE_PROP_CREATE_ERR

3-Error

Failed to create chasfs property [chars] rc=[dec]

Failure occured while creating chasfs property

asr900-system-rsp3

LOG_STD_ACTION

ASR900_PROTECTION-3-TDL_MSG_FAIL

3-Error

Failed to send the protection-physical [chars] TDL msg for protection interface [chars] and member [chars]

Whenever there is any error while sending the TDL msg for binding/unbinding a physical controller with UPSR/ACR controller

asr900-protection

LOG_STD_ACTION

EQPT_ALARM_PERSISTENCY-3-EQPT_ALARM_INFO_NULL

3-Error

Persistent alarm queue alarm info is NULL

-

-

-

EQPT_ALARM_PERSISTENCY-3-EQPT_ALARM_QUEUE_NULL

3-Error

Persistent alarm queue info is NULL

-

-

-

EQPT_ALARM_PERSISTENCY-3-EQPT_NULL_DATA_STRUCTURE

3-Error

[chars] is NULL

-

-

-

SPA_OIR_STATE_CHANGE-6-EMPTY

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state is in empty since the subslot is \ neither provisioned nor is it phsically \ populated with any interface module.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-IS_NR

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to in-service and \ normal. It is fully operational and shall \ provide provisioned functions.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-2-OOS_AU_MEA

2-Critical

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous and mismatch. An improper equipment \ is provisioned or inserted in the bay.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AU_SWDL

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous and software download.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AU_UEQ

6-Information

SPA N/A in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service autonomous \ because the card is not physically present.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-2-OOS_AUMA_MEA_MT

2-Critical

SPA N/A in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous management - mismatch and maintenance \ because the entity has been manually removed from \ service for a maintenance activity. Also the card \ may be inserted in the wrong slot.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-2-OOS_AUMA_UAS_MEA

2-Critical

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

-

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AUMA_SWDL_MT

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous - software download and maintenance. \ The entity had been manually removed from \ for a maintenance activity.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AUMA_UEQ_MT

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous - unequipped and maintenance. \ The card is not physically present. The entity \ has been manually removed from service for a \ maintenance activity.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AUMA_UAS

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous management - unassigned because \ the card is not provisioned in the database.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AUMA_FLT_MT

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous management - unequipped and \ unassigned because the card is neither \ physically present nor provisioned in the database.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_MA_MT

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ management. The entity had been manually \ removed from service for a maintenance activity \ but still performs its provisioned functions.

asr900-csl

LOG_STD_NO_ACTION

SPA_OIR_STATE_CHANGE-6-OOS_AU_FLT

6-Information

SPA [chars] in subslot 0/[dec] state transitioned to [chars].

The state transitioned to out of service \ autonomous - fault condition.

asr900-csl

LOG_STD_NO_ACTION

UEA_OIR-3-SPA_MISMATCH

3-Error

SPA [chars] mismatch in subslot 0/[dec]

During the router operation we check if the inserted IM is matching with the IM type that was configured on the subslot. If not a mismatch event is said to have occured.

asr900-csl

LOG_STD_ACTION

UEA_SPA_MODE-6-UEA_SPA_MODE_CHG

6-Information

SPA[chars] mode changed from [chars] to [chars] at subslot 0/[dec]

SPA Operating mode has been changed. SPA will be reloaded now.

asr900-csl

LOG_STD_NO_ACTION

SPA_FANTRAY_COMBO_NOT_SUPPORTED-2-INVALID_COMBINATION

2-Critical

SPA : [chars] at bay [dec] is not supported with fan [chars]

-

-

-

PEGA_PTP_ENABLER-3-PEGA_PTP_LICENSE_EULA_NOT_ACCEPTED

3-Error

\n********************************************************* \ \nWARNING: PTP License is not yet activated. \ \nPlease configure 'license feature ptp'\ \n*********************************************************\n

-

-

LOG_STD_ACTION

EWLC_L2-3-BULK_SYNC

3-Error

[chars]

Bulk sync failure the reason for the failure will be provided in the string

platform-ha

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

EWLC_L2-3-INVALID_MSG_RECEIVED

3-Error

Invalid [chars] message received

A message that is used for state synchronization was not received correctly. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized.

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2-3-MALLOC_FAILURE

3-Error

[chars]

Failed to allocated memory for a structure or event

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2-3-MAC_FAILURE

3-Error

Mac Failure

NULL MAC

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2-3-REG_FAILURE

3-Error

Message:[chars]Error:[dec]

Registration Failure

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2-3-FILE_OPEN_FAILURE

3-Error

File [chars] open failed

File Open failed

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2-3-OIR_FAILURE

3-Error

Message:[chars]Error:[dec]

EWLC L2 failures due to various reasons

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2_ISSU-3-INIT

3-Error

EWLC L2 ISSU client initialization failed at [chars] error [chars]

EWLC L2 ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

platform-ha

LOG_STD_SH_TECH_ACTION

EWLC_L2_ISSU-3-TRANSFORM

3-Error

EWLC L2 ISSU client [chars] transform failed error [chars]

EWLC L2 ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the EWLC L2 state will not\n\ be indentical with the active unit.

platform-ha

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

EWLC_L2_ISSU-3-MSG_NOT_OK

3-Error

EWLC L2 ISSU client message [dec] is not compatible

EWLC L2 ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

EWLC_L2_ISSU-3-MSG_SIZE

3-Error

EWLC L2 ISSU client failed to get the message size for message [dec]

EWLC L2 ISSU client failed to calculate message size\n\ for the message specified. The EWLC L2 ISSU client will not\n\ be able to send message to the standby unit.

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

EWLC_L2_ISSU-3-SESSION

3-Error

EWLC L2 ISSU client [chars]

EWLC L2 ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

EWLC_L2_ISSU-3-SESSION_UNREGISTRY

3-Error

EWLC L2 ISSU client failed to unregister session information. Error: [dec] [chars]

The EWLC L2 ISSU client failed to unregister session information.

platform-ha

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

EWLC_L2_ISSU-3-SEND_FAILED

3-Error

EWLC L2 ISSU client failed to send a negotiation message error [dec]

EWLC L2 ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

EWLC_L2_ISSU-3-BUFFER

3-Error

EWLC L2 ISSU client failed to get buffer for message error [dec]

EWLC L2 ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

EWLC_L2_ISSU-3-CAPABILITY

3-Error

EWLC L2 ISSU client [chars]

EWLC L2 ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

EWLC_L2_ISSU-3-POLICY

3-Error

EWLC L2 ISSU client message type [dec] is [chars]

EWLC L2 ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

platform-ha

"show issu session <client_id>"

EWLC_L2_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

EWLC L2 ISSU client capability exchange result incompatible.

The EWLC L2 ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

platform-ha

"show issu negotiated capability <Session_ID>"

EWLC_L2_ISSU-3-CAP_INVALID_SIZE

3-Error

EWLC L2 ISSU client capability list is empty.

The EWLC L2 ISSU client capability exchange list size\n\ is invalid.

platform-ha

"show issu capability entries <Client_ID>"

EWLC_PLATFORM-4-REC_DISK

4-Warning

System is running on a disk lower than recommended. Current Disk Size: [dec]GB Recommended Disk Size: [dec]GB

System is running on a disk lower than recommended. Please refer to release notes.

-

LOG_STD_NO_ACTION

EWLC_PLATFORM-4-REC_MEM

4-Warning

System is running with memory lower than recommended. Current Memory: [dec]GB Recommended Memory: [dec]GB

System is running with memory lower than recommended. Please refer to release notes.

-

LOG_STD_NO_ACTION

EWLC_PLATFORM-4-REC_CPU

4-Warning

System is running with CPUs lower than recommended. Current no of CPUs: [dec] Recommended no of CPUs: [dec]

System is running with CPUs lower than recommended. Please refer to release notes.

-

LOG_STD_NO_ACTION

EWLC_PLATFORM-3-PROCESS_CREATE_FAILED

3-Error

System resource check failed.

System resource check failed. System could be running on unsupported hardware resources

-

LOG_STD_NO_ACTION

EWLC_PLATFORM-4-UNKNOWN_EVENT

4-Warning

Unknown event [dec] [dec]

Unknown event occurred.

-

LOG_STD_NO_ACTION

EWLC_CAPWAP_IDB-3-IFINDEX_ZERO

3-Error

[chars] : ifindex is zero for interface [chars]. Unit : [dec] Slot : [dec]

IFINDEX of a capwap idb is zero.

-

"show idb"

BP_CRIMSON-3-INITFAIL

3-Error

Initialization of the IOS BP Crimson facility failed [chars].

-

-

-

IR8340_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_ASSERT

0-Emergency

External alarm/digital IO port [chars] asserted\n

External alarm/digital IO port alert is detected

-

"No action recommended" LOG_STD_ACTION

IR8340_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_CLEAR

0-Emergency

External alarm/digital IO port [chars] cleared\n

External alarm/digital IO port alert is cleared

-

"No action recommended" LOG_STD_ACTION

PLATFORM_MATM-3- INVALID_MSG_RECEIVED

3-Error

MATM received invalid SPI message.

A messages that was to be received from the hardware module was not received correctly. Mac address learning/ageing might be impacted as a result. The failure most likely occurred because of a software communication error.

firmware

LOG_STD_SH_TECH_ACTION

PLATFORM_MATM-4- QUEUE_OVERLIMIT

4-Warning

MATM dropped [chars] messages as queue limit has reached.

Messages received from the hardware module were not processed because an internal queue was full. Mac address learning/aging might be impacted as a result.

firmware

LOG_STD_SH_TECH_ACTION

ESG_MEMORY_UPGRADE-3-CONF_FAILED

3-Error

Configuration of memory failed.

An error occurred when memory configuration was attempted.

iosxe-csl

-

MODULE_STATE-3-MOD_TIMEOUT

3-Error

Timeout waiting for modules to come on-line.

One or more modules can not come on-line.

esg-chassismgr

-

MODULE_STATE-6-ALL_MODULES_UP

6-Information

All modules are now on-line.

All modules are now on-line.

esg-chassismgr

-

ISR_THROUGHPUT-3-SETUP_FAILED

3-Error

Throughput upgrade license set up failed

An error occurred when setting up the throughput upgrade licenses.

iosxe-csl

-

ISR_THROUGHPUT-6-LEVEL

6-Information

Throughput level has been set to [dec]00 kbps

Throughput level has been set to a number

iosxe-csl

-

ISR_THROUGHPUT-6-CRYPTO

6-Information

Crypto level has been set to [dec]00 kbps

Crypto level has been set to a number

iosxe-csl

-

ISR_THROUGHPUT-6-UNTHROTTLED

6-Information

Crypto level is unthrottled

Crypto level has been unthrottled

iosxe-csl

-

ISR_THROUGHPUT-3-CONF_FAILED

3-Error

Configuration failed

An error occurred when the throughput configuration was attempted.

iosxe-csl

-

ISR_THROUGHPUT-3-EULA_NOT_ACCEPTED

3-Error

The EULA has to be accepted prior to throughput configuration.

Users need to accept EULA to activate the license

iosxe-csl

"Accept EULA for throughput license"

ISR_THROUGHPUT-3-INVALID_CONFIG

3-Error

An invalid throughput config: [chars] kbps was selected.

The configured throughput is unknown

iosxe-csl

-

BOOST_PERFORMANCE-2-CONFIG_REMOVED

2-Critical

Boost capability removed. Throughput will be defaulted on next reload. Reason: [chars]

Device no longer support boost throughput level

isr-smart-lic

-

ASYNC_IF-0-DTR_SET_FAIL

0-Emergency

Failed to set DTR state..

Failed to set DTR Data Terminal Ready state.

esr6k3-async

LOG_ERR

ASYNC_IF-0-DSR_READ_FAIL

0-Emergency

Failed to read DSR state..

Failed to read DSR Data Set Ready state.

IIOT_COMPONENT

LOG_ERR

IIOT_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_ASSERT

0-Emergency

External alarm/digital IO port [chars] asserted\n

External alarm/digital IO port alert is detected

-

"No action recommended" LOG_STD_ACTION

IIOT_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_CLEAR

0-Emergency

External alarm/digital IO port [chars] cleared\n

External alarm/digital IO port alert is cleared

SPARROW_COMPONENT

"No action recommended" LOG_STD_ACTION

PLATFORM-5-CONFIG_RECOVERY

5-Notice

IOS Configuration recovery is in progess.

-

-

LOG_STD_NO_ACTION

PLATFORM-5-RESET_BUTTON

5-Notice

Reset Button pressed during boot up.

-

-

LOG_STD_NO_ACTION

DECLASSIFICATION-3-UNABLE_TO_RESET_CONFIG

3-Error

[chars]

The system is unable to reset the configuration

firmware

LOG_STD_ACTION

DECLASSIFICATION-5-CONFIG_IS_RESET

5-Notice

[chars]

The configuration is reset and the system will now reboot

firmware

LOG_STD_ACTION

GPS_DR-0-MODULE_FAIL_INIT

0-Emergency

Failed to initialize the GPS/DR module.

Failed to initialize the GPS/DR module.

-

LOG_STD_ACTION

GPS_DR-0-MODULE_FAIL_AUTHENTICATION

0-Emergency

Failed to authenticate the GPS/DR module: [chars] return code 0x[hec].

Failed to authenticate the GPS/DR module.

TAMPER_COMPONENT

LOG_STD_ACTION

PLATFORM-0-SLOT_REMOVED

0-Emergency

[chars] cover/module removed\n

-

-

-

PLATFORM-0-SLOT_INSERTED

0-Emergency

[chars] cover/module inserted\n

-

-

-

PLATFORM-0-PIN_REMOVED

0-Emergency

[chars] pin removed\n

-

-

-

PLATFORM-0-PIN_INSERTED

0-Emergency

[chars] pin inserted\n

-

-

-

PLATFORM-0-MODULE_REMOVED

0-Emergency

[chars] module removed\n

-

-

-

PLATFORM-0-MODULE_INSERTED

0-Emergency

[chars] module inserted\n

-

-

-

IGNITION-5-IGN_DEBUG_SET

5-Notice

Ignition Management debugging [chars] is turned [chars]

The system's debugging facility is turned on or off

aventus-platform

LOG_STD_NO_ACTION

IGNITION-4-IGN_FAILED_CMD

4-Warning

Ignition Management hardware failed to execute the '[chars]' command. Code: [dec]

The hardware MCU responsible for the ignition power management is not responding properly to software commands.

aventus-platform

LOG_STD_RECUR_ACTION

IGNITION-5-IGN_ENABLE_CMD

5-Notice

The Ignition Power Management is [chars]

The system administrator has enabled the Ignition Power Management feature.

aventus-platform

LOG_STD_NO_ACTION

IGNITION-5-IGN_SENSE_CMD

5-Notice

The Ignition Voltage Sense is [chars]

The system administrator has enabled the Ignition Voltage Sense feature.

aventus-platform

LOG_STD_NO_ACTION

IGNITION-5-IGN_TURNED_ON_OFF

5-Notice

The ignition is turned [chars]

The ignition state changed between ON and OFF.

aventus-platform

LOG_STD_NO_ACTION

IGNITION-4-IGN_OVER_VOLTAGE

4-Warning

The input voltage is at [dec].[dec] V. The overvoltage threshold of [dec].[dec] V has been tripped recently. Shutdown sequence will begin.

The input voltage became higher than the overvoltage threshold and the router might shutdown shortly.

aventus-platform

"Reduce the input power supply voltage."

IGNITION-4-IGN_UNDER_VOLTAGE

4-Warning

The input voltage below the undervoltage threshold of [dec].[dec] V was detected. The system may shutdown.

The input voltage became lower than the undervoltage threshold and the router might shutdown shortly.

aventus-platform

"Increase the input power supply voltage."

IGNITION-4-IGN_UNDER_VOLTAGE_END

4-Warning

The input voltage above the undervoltage threshold of [dec].[dec] V was detected.

The input voltage became higher than the undervoltage threshold.

aventus-platform

LOG_STD_NO_ACTION

IGNITION-5-IGN_RELOAD_SYS

5-Notice

The Ignition Power Management is preparing for shutdown

The Ignition Power Management is about to shut the system down.

aventus-platform

LOG_STD_NO_ACTION

IGNITION-4-IGN_REJECT_SETTING

4-Warning

Incompatible 'under voltage' setting [dec].[dec] V was not applied. The

The under voltage threshold value was set to a higher value then actual input voltage and applying this setting would cause the router to shutdown shortly

aventus-platform

LOG_STD_RECUR_ACTION

VDD-3-NULL_CB

3-Error

Supplied [chars] control block is NULL. [chars]

An NULL control block was passed internally in the software as part of an operation to read or write to the required register or memory address. As a consequence the operation could not be processed and the address contents is now out of sync with what it should be if the operation was a write or an incorrect value returned if the operation was a read.

-

LOG_STD_ACTION

VDD-3-NULL_SPACE_CB

3-Error

Supplied [chars] space control block is NULL. [chars]

An NULL space control block was passed internally in the software as part of an operation to read or write to the required address. As a consequence the operation could not be processed and the address contents is now out of sync with what it should be if the operation was a write or an incorrect value returned if the operation was a read.

-

LOG_STD_ACTION

VDD-3-SIZE_TOO_LARGE

3-Error

An attempt was made to create a [chars] of size [dec] bits. \[chars]\. The maximum size supported is [dec] bits. Operation aborted.

The virtual device driver architecture only supports a maximum as indicated by the message. A request to create an entry greater in size than the limit has been made which is not possible to process. The consequence is that the entry will not be created leading to loss of data the entry was supposed to maintain.

-

LOG_STD_ACTION

OPTICAL_IF-3-INTERNAL_ERROR

3-Error

[chars]

The metopt subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

OPTICAL_IF-1-ALARM

1-Alert

[chars] [chars]: [chars]

The specified Alarm has been declared or cleared

-

"Recommended action is to repair the source of the alarm."

CM_SYNC-3-TRANSMIT_ERROR

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to msg translation

-

LOG_STD_ACTION

CM_SYNC-3-NO_BUFFER

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to non-availability of buffer

-

LOG_STD_ACTION

OPTICAL_MONITOR-4-FAILED

4-Warning

[chars] [chars]

Monitoring cannot be turned on for rate specified with current h/w version.

-

LOG_STD_ACTION

OPTICAL_IF_ALARMS-3-LOW_ALM_THR

3-Error

Low Alarm Threshold for [chars] on port [chars] [chars]

Low alarm threshold was exceeded.

-

LOG_STD_ACTION

OPTICAL_IF_ALARMS-3-LOW_WARN_THR

3-Error

Low Warning Threshold for [chars] on port [chars] [chars]

Low warning threshold was exceeded.

-

LOG_STD_ACTION

OPTICAL_IF_ALARMS-3-HIGH_ALM_THR

3-Error

High Alarm Threshold for [chars] on port [chars] [chars]

High alarm threshold was exceeded.

-

LOG_STD_ACTION

OPTICAL_IF_ALARMS-3-HIGH_WARN_THR

3-Error

High Warning Threshold for [chars] on port [chars] [chars]

High warning threshold was exceeded.

-

LOG_STD_ACTION

PATCH-3-CHANNEL_MISMATCH

3-Error

Channel mismatch between [chars] and [chars]

Channel mismatch when creating patch.

-

LOG_STD_ACTION

PWD_SYNC -2-INITSYS

2-Critical

[chars]

A software error occurred during initialization of the Password Sync RF subsystem

-

"Check for sufficient processor memory." LOG_STD_ACTION

PWD_SYNC-3-TRANSMIT_ERROR

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to msg translation

-

LOG_STD_ACTION

PWD_SYNC-3-NO_BUFFER

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to non-availability of buffer

-

LOG_STD_ACTION

PWD_SYNC-3-UNKNOWN_MSG

3-Error

Unknown message type 0x[hec] received by [chars]

An unknown message type was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

PWD_SYNC-3-SUBSYS_COMPAT

3-Error

Standby is missing the Password Sync subsystem hence Standby will not have password protection for the privilaged mode.

Standby CPU software subsystem is older or missing. See message text for software subsystem type. May result in feature losses in the event of a switchover.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

PWD_SYNC-3-INVALID_MSG

3-Error

Incorrectly formatted message 0x[hec] 0x[hec] received by [chars]

Inconsistent message data was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

PWD_SYNC-5-UNSUPPORTED_MSG

5-Notice

Msgtype [chars] sent by [chars] unsupported by peer.

Peer responded that it didn't recognize a message sent by this CPU possibly due to a different image version.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

PWD_SYNC-6-SYNC_MSG

6-Information

Successfully Synced [chars] Password.

Active CPU successfully synced the password to Standby CPU

-

LOG_STD_NO_ACTION

PWD_SYNC-6-CONSOLE_TIMEOUT_SYNC_MSG

6-Information

Console EXEC Timeout successfully synced to Standby

Active CPU successfully synced console exec timeout to Standby CPU

-

LOG_STD_NO_ACTION

CPU_REDUN -2-INITSYS

2-Critical

[chars]

A software error occurred during initialization of the CPU redundancy subsystem

-

"Check for sufficient processor memory." LOG_STD_ACTION

CPU_REDUN-3-INIT_ERROR

3-Error

[chars] [dec] [dec]

A subsystem initialization error occurred.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-NEGOTIATED_SWITCHOVER

5-Notice

[chars] [dec]

Reloading due to a negotiated switchover.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-STATE_MISMATCH_RELOAD

5-Notice

[chars]

Reloading due to a hardware software state mismatch.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-RELOAD_COMM_DOWN

5-Notice

[chars]

Reloading standby since Active CPU shows loss of comm.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-STATUS_CHG

5-Notice

[chars] sev [dec] peer is [chars] sev [dec]

A CPU hardware redundancy status change occurred.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-PEER_EXITED_IOS

5-Notice

Peer CPU has exited IOS

Peer CPU has exited IOS.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-PEER_REMOVED

5-Notice

Peer CPU has been removed from the chassis

Peer CPU has been removed from the chassis.

-

LOG_STD_NO_ACTION

CPU_REDUN-3-LOCK_ERR

3-Error

Can't get Global Lock

Peer CPU won't relinquish the arbitration lock.

-

"Check that both the local and peer CPUs " "are fully seated in the backplane. Check " "the health of the Peer CPU." LOG_STD_ACTION

CPU_REDUN-4-UNPROTECTED

4-Warning

[chars] [dec] [chars]

System is running for an extended period in an unprotected mode even though a peer CPU is present

-

"Check the health of the Peer CPU. Configure as " "maintenance mode to intentionally suppress error " "messages." LOG_STD_ACTION

CPU_REDUN-3-PEER_STATE_ERR

3-Error

Invalid peer CPU state [chars] current peer register=0x[hec]

Peer CPU is reporting an invalid redundancy state.

-

"Check that both the local and peer CPUs " "are fully seated in the backplane. Check " "the health of the Peer CPU." LOG_STD_ACTION

CPU_REDUN-3-PEER_SEVERITY_ERR

3-Error

Invalid peer CPU severity [dec] current peer register=0x[hec]

Peer CPU is reporting an invalid severity value.

-

"Check that both the local and peer CPUs " "are fully seated in the backplane. Check " "the health of the Peer CPU." LOG_STD_ACTION

CPU_REDUN-3-INVALID_CPU_STATES

3-Error

Detected invalid redundancy states local = [chars] peer = [chars]

Detected an invalid combination of redundant states

-

LOG_STD_NO_ACTION

CPU_REDUN-3-SW_STATE_MISMATCH

3-Error

Software state [chars] doesn't reflect local hardware [chars]

Software state is not following the underlying hardware redundancy state

-

LOG_STD_ACTION

CPU_REDUN-3-READBACK_ERR

3-Error

Can't change my state. desired state [chars] read-back [chars]

Local CPU can't set its redundancy state to the desired calculated value

-

"Check health of local CPU." LOG_STD_ACTION

CPU_REDUN-5-FORCE_CLOSE

5-Notice

Forcibly closing fd: [dec] name:[chars]

A file activity timeout occurred on the slave.

-

LOG_STD_NO_ACTION

CPU_REDUN-6-RUNNING_CONFIG_CHG

6-Information

Running config on this CPU has possibly changed

Informational message to notify of possible changes to the running-config file

-

LOG_STD_NO_ACTION

CPU_REDUN-3-RCSF_FAIL

3-Error

Attempt to sync running config to standby failed

Unable to send Running Config file to Standby CPU

-

LOG_STD_NO_ACTION

CPU_REDUN-5-RCSF_SYNCED

5-Notice

Running config successfully synced to standby

Running Config file was sent to the Standby CPU

-

LOG_STD_NO_ACTION

CPU_REDUN-6-STARTUP_CONFIG_CHG

6-Information

Startup config on this CPU has possibly changed

Informational message to notify of possible changes to the startup-config file

-

LOG_STD_NO_ACTION

CPU_REDUN-3-STARTUP_SYNC_FAIL

3-Error

Attempt to sync [chars] config to standby failed

Unable to send Startup or Private Config file to Standby CPU

-

LOG_STD_NO_ACTION

CPU_REDUN-5-STARTUP_CONFIG_SYNCED

5-Notice

Startup config successfully synced to standby

Startup Config file was sent to the Standby CPU

-

LOG_STD_NO_ACTION

CPU_REDUN-3-EHSA_SVCS

3-Error

[chars] [chars]

An error occurred that affects CPU Redundancy services. The details about what was attempted and what went wrong will be printed.

-

LOG_STD_ACTION

CPU_REDUN-5-EHSA_SVCS_RESP

5-Notice

Sending [chars] = [dec]

Normal response for CPU EHSA Redundancy services. The details about what was sent will be printed.

-

LOG_STD_NO_ACTION

CPU_REDUN-6-EHSA_SVCS_EVENT

6-Information

[chars] [chars]

A significant EHSA Redundancy services event occurred. The details will be printed.

-

LOG_STD_NO_ACTION

CPU_REDUN-3-CAPAB_SIZE

3-Error

Mismatch in [chars]. Active=[dec] Standby=[dec].

Standby CPU is reporting lower Capabilities than the Active CPU. See message text for type of limitation.

-

"Check for sufficient Standby CPU capabilities." LOG_STD_ACTION

CPU_REDUN-3-CAPAB_VERS

3-Error

Mismatch in [chars]. Active=[dec].[dec] Standby=[dec].[dec].

Standby CPU is reporting lower versions than the Active CPU. See message text for type of limitation.

-

"Check Standby CPU version numbers." LOG_STD_ACTION

CPU_REDUN-3-DRIVER_VERSIONS

3-Error

Mismatch in [chars] driver versions. Active=[dec].[dec] Standby=[dec].[dec].

Standby CPU is reporting lower versions than the Active CPU. See message text for type of limitation. May result in a loss of connections.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

CPU_REDUN-3-DRIVER_MISSING

3-Error

Missing [chars] driver support on Standby. Active=[dec].[dec]

Standby CPU is missing support for one of the drivers available on the Active CPU. The corresponding linecard will go down in the event of a switchover.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

CPU_REDUN-3-SUBSYS_COMPAT

3-Error

[chars] [chars] software subsystem. Active=[dec] Standby=[dec].

Standby CPU software subsystem is older or missing. See message text for software subsystem type. May result in feature losses in the event of a switchover.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

CPU_REDUN-5-BASIC_CAPABILITY

5-Notice

Peer CPU hardware and software is fully compatible.

Standby CPU H/W drivers and software subsystems have matching versions and capabilities.

-

LOG_STD_NO_ACTION

CPU_REDUN-3-4MSEC_DISABLED

3-Error

[chars] [dec]

The 4msec timer interrupt was shut off for an extended period while the hardware watchdog was enabled.

-

LOG_STD_ACTION

CPU_REDUN-3-INTRPT_HOG

3-Error

[chars] [dec] sec [chars] = [hec]

The CPU redundancy process didn't run for a long time because an interrupt routine ran too long.

-

LOG_STD_ACTION

CPU_REDUN-3-UNKNOWN_MSG

3-Error

Unknown message type 0x[hec] received by [chars]

An unknown message type was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

CPU_REDUN-3-INVALID_MSG

3-Error

Incorrectly formatted message 0x[hec] 0x[hec] received by [chars]

Inconsistent message data was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

CPU_REDUN-5-UNSUPPORTED_MSG

5-Notice

Msgtype [chars] sent by [chars] unsupported by peer.

Peer responded that it didn't recognize a message sent by this CPU possibly due to a different image version.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

CPU_REDUN-3-UNKNOWN_COMMON

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

If the alarm appears when this is asserted for a standby processor with a different software image it indicates an alarm condition on the peer that the active processor can not decode. If this is asserted for the active processor it indicates a software error condition.

-

LOG_STD_ACTION

CPU_REDUN-3-SRC_TEST

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the processor has failed the online diagnostic internal SRC test.

-

LOG_STD_ACTION

CPU_REDUN-3-PCI_TEST

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the processor has failed the online diagnostic internal PCI bus test.

-

LOG_STD_ACTION

CPU_REDUN-3-PCMCIA_TEST

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the processor has failed the online diagnostic internal PCMCIA slot test.

-

LOG_STD_ACTION

CPU_REDUN-3-GT_STATUS_REG

3-Error

Parity Error on PCI Bus from PCI Device

A Parity error on PCI bus has occurred while validating the GT64120 PCI device hanging off the PCI bus

ons155xx-cpu

"Check whether it is a GT64120 device.\n" LOG_STD_ACTION

CPU_REDUN-3-PCI_STATUS_REG

3-Error

Status error in PCI device [dec]

A PCI Status registry error in PCI device has been detected when validating the PCI device hanging off the PCI bus

ons155xx-cpu

"Check whether it is a valid PCI device Manhattan." "\n" LOG_STD_ACTION

CPU_REDUN-3-PCI_VENDORID_MISMATCH

3-Error

Error/Mismatch in reading Vendor ID for PCI device [dec]

The PCI Vendor ID error/mismatch has been detected when validating the PCI device hanging off the PCI bus

ons155xx-cpu

"Check the vendor ID of the PCI device attached it should of a macro value like: CLPD6729_VENDOR_ID" "\n" LOG_STD_ACTION

CPU_REDUN-3-MULTI_CARD_ACCESS

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the processor has failed the linecard access test for multiple linecards.

-

LOG_STD_ACTION

CPU_REDUN-3-SLOT_IDPROM_MISMATCH

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the slot ID read from the backplane IDPROM does not match the slot ID read from the SRC.

-

LOG_STD_ACTION

CPU_REDUN-3-BKPLN_IDPROM_ACCESS

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the processor can not access its backplane IDPROM.

-

LOG_STD_ACTION

CPU_REDUN-3-INCONSISTENT_STATES

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the processor redundancy state is either not consistent with the peer state or the software state is not consistent with the hardware state.

-

LOG_STD_ACTION

CPU_REDUN-3-PEER_SRC_REGS

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the active processor is detecting bad parity on the active/standby bits read from the standby processor.

-

LOG_STD_ACTION

CPU_REDUN-3-PEER_MISSING

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the peer processor is either missing or can not be detected. The active processor currently is not being protected.

-

LOG_STD_ACTION

CPU_REDUN-3-PEER_COMM

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the peer processor is present but not responding or sending keepalives.

-

LOG_STD_ACTION

CPU_REDUN-3-CAPABILITIES

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

The alarm appears when the capabilities reported by the standby processor are less than the active processor. The processors are conditionally redundant which means that a switchover could result in a partial loss of system control.

-

LOG_STD_ACTION

CPU_REDUN-3-UNKNOWN_PLAT

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

If the alarm appears when this is asserted for a standby processor with a different software image it indicates an alarm condition on the peer that the active processor can not decode. If this is asserted for the active processor it indicates a software error condition.

-

LOG_STD_ACTION

CPU_REDUN-3-UART_FAILURE

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

This alarm appears when the processor can't transmit characters on the console UART. It indicates a probable equipment failure

-

"If the symptom persists following a reload " "remove and replace the processor module."

CPU_REDUN-6-BOOTED_AS_ACTIVE

6-Information

After returning to ROM by [chars]

Informational message notifying about a system startup with no switchover.

-

LOG_STD_NO_ACTION

CPU_REDUN-5-SWITCHOVER

5-Notice

Switchover occurred. Reason: [chars]

A CPU switchover took place. The reported reason is listed in the error message text.

-

LOG_STD_NO_ACTION

CPU_REDUN-4-STARTUP_CONFIG_MISSING

4-Warning

Non-volatile configuration memory is not present

The startup-config is missing. This may be due to either a manual user erase command or an interrupted write to the startup-config.

-

"Do a copy running-config startup-config to save" "current system configuration. " LOG_STD_RECUR_ACTION

CPU_REDUN-4-REPROGRAM_ACTIVE_CPU

4-Warning

Active CPU FPGA has been \nreprogrammed. Please remove and re-insert the CPU in slot [dec] or\npower-cycle the box for the new FPGA to take effect.

Active CPU FPGA has been reprogrammed. This CPU is now running with old FPGA and it needs to be hot-swapped or the system needs to be power-cycled for the new FPGA to take effect.

-

LOG_STD_NO_ACTION

RF-1-SYSTEM_INTEGRITY

1-Alert

[chars]

An automatic switch of activity occurred when it had been disabled.

CPU

LOG_STD_ACTION

RF-3-STANDBY_RELOAD

3-Error

The standby CPU is being reset because [chars]

See the reported error message for the reason that the peer CPU was reset. This allows recovery from an indeterminate Standby state.

CPU

LOG_STD_ACTION

RF-3-SIMPLEX_MODE

3-Error

The peer CPU has been lost

The peer CPU absence has been detected

CPU

LOG_STD_ACTION

RF-6-DUPLEX_MODE

6-Information

The peer CPU has been detected

The peer CPU has been detected

CPU

LOG_STD_ACTION

RF-3-COMMUNICATION

3-Error

Communication with the peer CPU has been [chars]

The status of the peer CPU communication path has changed

CPU

LOG_STD_ACTION

RF-6-INHIBIT_SWITCH

6-Information

Redundancy client [chars] [chars] manual switchover

A redundancy client has changed the ability to manually cause a switch of activity.

CPU

LOG_NO_ACTION

RF-3-IPC_PORT

3-Error

Unable to [chars] [chars] <[chars]>

Not able to initialize the RF IPC port to the peer CPU.

CPU

LOG_NO_ACTION

ODM-3-LC_TEST_FAIL

3-Error

Slot [dec] [chars] [chars] Failed

Online diagnostic test failed for the card

-

LOG_STD_ACTION

ODM-3-SC_TEST_FAIL

3-Error

Slot [dec] Subcard [dec][chars] [chars] Failed

Online diagnostic test failed for the subcard

-

LOG_STD_ACTION

ODM-3-CPU_TEST_FAIL

3-Error

CPU card[chars] [chars] Failed

Online diagnostic test failed for this CPU

-

LOG_STD_ACTION

ODM-3-LC_DIAGS_DISABLED

3-Error

Slot [dec] after [dec] Failures

Online diagnostic tests were disabled because of \n\ multiple failures

-

LOG_STD_ACTION

ODM-3-SC_DIAGS_DISABLED

3-Error

Slot [dec] Subcard [dec] after [dec] Failures

Online diagnostic tests were disabled because of \n\ multiple failures

-

LOG_STD_ACTION

ODM-3-DIAG_DISABLE

3-Error

Online Diags disabled for all slots without specific config

Online Diagnostic tests were disabled for all slots except those with specific config

-

LOG_STD_ACTION

ODM-3-DIAG_ENABLE

3-Error

Online Diags enabled for all slots without specific config

Online Diagnostic tests were enabled for all slots except those with specific config

-

LOG_STD_ACTION

ODM-3-PEER_INCOMPATIBLE

3-Error

Online Diags Peer Version is different

Version of the peer Online Diagnostics Manager is different

-

LOG_STD_ACTION

APS -2-INITSYS

2-Critical

[chars]

A software error occurred during initialization of\n\ the APS subsystem

-

"Check for sufficient processor memory." LOG_STD_ACTION

APS-3-PORT_FAIL

3-Error

[chars] Port Fail On [chars]

This message is posted when APS subsystem receives\n\ a port fail indication from the driver subsystem.\n\ This message indicates that the specified interface\n\ has detected a failure condition\n\ e.g. Loss Of Light.

-

"Isolate the cause of the failure and restore\n\ the interface to normal operational\n\ condition."

APS-1-NO_ACTIVE

1-Alert

No Active Port In Group [chars]

After an active interface failure the system\n\ switches over to the standby interface if APS has\n\ been enabled. This message is posted if after a\n\ switchover the system finds no active interface\n\ i.e. both working and protection interfaces are\n\ found to be nonoperational.

-

"Isolate the cause of failure on both working\n\ and protection interfaces."

APS-6-AUTOFOVER

6-Information

Auto-Failover - Group [chars]

This message is posted if APS hardware\n\ successfully switched over to the standby interface\n\ after the failure of the active interface. This is\n\ informational only.

-

"Isolate the cause of failure of the previous\n\ active interface and restore it to a working\n\ condition."

APS-2-INTRNLERR

2-Critical

[chars] [dec]

APS software detected an internal error

-

LOG_STD_ACTION

APS-6-ENAUTFOVR

6-Information

Enable Auto-Failover On [chars]

This message is posted when APS software enables\n\ hardware to perform APS actions for failures\n\ detected by the hardware. This is informational\n\ only.

-

LOG_STD_NO_ACTION

APS-6-DISAUTFOV

6-Information

Disable Auto-Failover On [chars]

APS has disabled auto-failover for the indicated\n\ group

-

show aps group <name>

APS-6-ADJUSTMODE

6-Information

Group [chars]: Mode Mismatch - [chars]

This message is posted by the local network element\n\ if the local APS group has been configured for\n\ bidirectional operation but the associated remote\n\ APS group has been configured for unidirectional\n\ operation. This message is posted after the local\n\ network element detects the mismatch and changes\n\ the operation to unidirectional.

-

"Configure the remote APS group for\n\ bidirectional operation."

APS-6-BIDIRSWCH

6-Information

Group [chars]: Remote Request - [chars]

This message is posted by the local network element\n\ after an APS switchover that is triggered by an APS\n\ request from the remote network element. This is\n\ informational only.

-

LOG_STD_NO_ACTION

APS-2-CHNLCFGMM

2-Critical

Group [chars]: Channel Config Mismatch

Working and Protection interfaces do not point to the\n\ same path on local and remote network elements

-

"Configure working and protection interfaces\n\ to point to the same path on local and remote\n\ network elements"

APS-2-PSBF

2-Critical

Group [chars]: Prot Switch Byte Failure - [chars]

-

-

"Check for failures on the APS communication\n\ channel. Isolate the cause for such failures\n\ and restore the communication channel to\n\ working condition"

APS-2-MODEMISMATCH

2-Critical

Group [chars]: Mode Mismatch - [chars]

-

-

"Configure the remote APS group for\n\ bidirectional operation."

APS-2-CHNLMISMATCH

2-Critical

Group [chars]: Channel Mismatch - [chars]

-

-

"Check for any failures on the APS commnication\n\ channel. If APS communication channel is\n\ operational contact Cisco TAC."

APS-2-FEPF

2-Critical

Group [chars]: Far End Prot Failure - [chars]

-

-

"Isolate the cause of failure on the protection\n\ channel on the remote network element."

APS-2-NOSOCKET

2-Critical

Failed To Open Socket

This message is posted when the APS subsystem fails\n\ to create a UDP socket for exchanging APS channel\n\ protocol messages over APS message channel configured\n\ for IP. This usually is due to a low memory condition\n\ in the system

-

LOG_STD_REDUCE_ACTION

APS-6-CHNLACTIVE

6-Information

Group [chars] - [chars] channel is now ACTIVE

This message is posted when a previously standby\n\ channel becomes the active channel. This is\n\ informational only.

-

LOG_STD_NO_ACTION

OSCP-4-BADPACKET

4-Warning

Invalid pkt: [chars] [dec] [dec]

An invalid packet was received from a network peer.

-

"Check the originating device for a cause of the corrupted\n\ packets."

OSCP-3-INTERNAL_ERROR

3-Error

[chars] [hec]

An internal software error occurred. The message contains more\n\ information that can be used to identify the problem.

-

LOG_STD_ACTION

OSCP-4-CONFIG_ERROR

4-Warning

Configuration Error: [chars]

This message indicates a configuration error in the OSCP subsystem.\n\ The message will display more specific information about the\n\ cause of problem.

-

"Change the configuration to correct the error."

OSCP-7-DEBUG

7-Debug

[chars]

This is an informational message only. It is used by Cisco\n\ for testing.

-

"Informational messages can be disabled by changing logging level."

INTF_SYNC -2-INITSYS

2-Critical

[chars]

A software error occurred during initialization of the Interface Sync RF subsystem

-

"Check for sufficient processor memory." LOG_STD_ACTION

INTF_SYNC-3-TRANSMIT_ERROR

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to msg translation

-

LOG_STD_ACTION

INTF_SYNC-3-NO_BUFFER

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to non-availability of buffer

-

LOG_STD_ACTION

INTF_SYNC-3-UNKNOWN_MSG

3-Error

Unknown message type 0x[hec] received by [chars]

An unknown message type was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

INTF_SYNC-3-INVALID_MSG

3-Error

Incorrectly formatted message 0x[hec] 0x[hec] received by [chars]

Inconsistent message data was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

INTF_SYNC-5-UNSUPPORTED_MSG

5-Notice

Msgtype [chars] sent by [chars] unsupported by peer.

Peer responded that it didn't recognize a message sent by this CPU possibly due to a different image version.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

METOPT-2-NOMEMORY

2-Critical

No memory available for [chars]

An attempt at memory allocation failed.

-

"Try these actions to remedy the problem:\n\ \n\ Add memory.\n\ \n\ Disable some features.\n\ \n\ Apply filtering to decrease the size of system data structures - the\n\ routing table for example.\n\ \n\ In general reduce other system activities to ease memory demands. If\n\ conditions warrant upgrade to a larger memory configuration."

METOPT-2-NOPAKBUFFER

2-Critical

No packet buffer available for [chars] interface to send this packet to higher layer

An attempt to allocate packet buffer failed.

-

"Try these actions to remedy the problem:\n\ \n\ Reload the system.\n\\n\ Perform a CPU switchover if you\n\ have a redundant CPU system"

METOPT-3-NOMAC

3-Error

Can't allocate MAC address for interface [dec]/[dec]

MAC address allocation failed because of an incorrect slot and port combination which exceeds the maximum available hardware

man-optical-sw

"Check whether all the available MAC addresses for the system have been allocated" "Make sure that this address is unique or specify MAC addresses for commands such as novell routing that allow the use of this address as a default.\n" LOG_STD_ACTION

METOPT-4-COOKIE

4-Warning

Corrupt or missing MAC address cookie using random base [enet]\n

The contents of MAC address EEPROM are invalid. The system is providing random MAC addresses

man-optical-sw

"show rpm eeprom" "\n" LOG_STD_RECUR_ACTION

METOPT-4-NOCPUVER

4-Warning

Invalid CPU ID assuming revision 1

The CPU ID could not be read from EEPROM.\n\ This is probably due to a hardware failure.

-

LOG_STD_ACTION

METOPT-6-DI_ASSERTED

6-Information

CDL Defect Indication: [chars] Asserted on interface [chars]\n

This message indicates some CDL Defect \n\ Indication bits were Asserted on this interface \n

-

"Closely monitor CDL Defect Indication Status \n\ if Defect Indication was asserted"

METOPT-6-DI_CLEARED

6-Information

CDL Defect Indication: [chars] cleared on interface [chars]\n

This message indicates CDL Defect \n\ Indication Status Changed\n

-

LOG_STD_NO_ACTION

METOPT-2-FABRIC_PORTFAIL

2-Critical

Port Fail event received from [chars] switch card on fabric port associated with interface [chars]\n

Fabric Port Failed due to some problem\n

-

LOG_STD_ACTION

METOPT-2-ZEROLEN_MSG

2-Critical

Zero length while [chars] linecard. Datalen [dec]\n

Due to some internal error a zero length transaction is being made from/to the Line card

-

LOG_STD_ACTION

METOPT-3-UNEXP_INTR

3-Error

Interrupt [chars] not expected masking off

An interrupt of a certain type was signalled but the \n\ interrupt handler for this type of interrupt is not yet installed.

-

"This problem should be self-correcting but indicates either\n\ a hardware or a software defect. If it's a hardware defect\n\ further problems are to be expected. If it's a software\n\ problem certain types of error and alarm conditions may be\n\ left undetected. \n\ Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ENVM-3-NOFORK

3-Error

Could not start environment polling process

The software could not spawn the enviromental monitoring\n\ process possibly because of low memory - no monitoring\n\ will be performed.

-

LOG_STD_REDUCE_ACTION

ENVM-3-LASTENV

3-Error

[chars]

Non volatile EEPROM storage of environmental statistics failed.\n\ This may be due to an EEPROM hardware failure.

-

LOG_STD_ACTION

ENVM-3-NOACK

3-Error

Access to [chars] failed

One of the temperature sensors was not ready for \n\ the initiation of temperature environmental monitoring.\n\ Software is attempting to restart the sensor.

-

LOG_STD_RECUR_ACTION

ENVM-4-ENVWARN

4-Warning

[chars] measured at [chars]

One of the measured environmental test points exceeds the warning \n\ threshold.

-

"Closely monitor the condition and correct if possible. " LOG_STD_RECUR_ACTION

ENVM-2-ENVCRIT

2-Critical

[chars] measured at [chars]

One of the measured environmental test points exceeds an extreme \n\ threshold.

-

"Correct the specified condition or the system may shut itself down\n\ as a preventive measure.\n\ This condition could cause the system to fail to operate properly. " LOG_STD_RECUR_ACTION

ENVM-6-PSCHANGE

6-Information

[chars] changed from [chars] to [chars]

This message indicates the absence or detection\n\ of a new type of power supply in the system.\n\ This can be expected when hot-swapable power supplies are swapped.\n\ This is an informational message only.

-

LOG_STD_NO_ACTION

ENVM-6-PSLEV

6-Information

[chars] state changed from [chars] to [chars]

One of the power supply test points underwent a state change.

-

"Closely monitor the condition and correct if possible. " LOG_STD_RECUR_ACTION

ENVM-3-BLOWER

3-Error

[chars] may have failed

One of the router's cooling fans may be close to failure.

-

"Replace the fan as soon as possible or the system may shut itself \n\ down or fail to operate properly."

ENVM-0-SHUT

0-Emergency

Environmental Monitor initiated shutdown

The enviromental monitor has initiated a system shutdown.

-

"Look at previous environmental messages to determine cause of \n\ shutdown and correct if possible. " LOG_STD_ACTION

OIR-3-BADIDPROM

3-Error

IDPROM in slot [dec] not properly programmed

IDPROM is not programmed correctly

-

"Contact customer support."

OIR-3-BADFPGAIMG

3-Error

Controller in in slot [dec] does not have a valid FPGA image

Invalid FPGA image in slot\n

-

"Contact customer support."

OIR-3-DETECT

3-Error

Detected [chars] in slot [dec]

Type of card detected in slot\n

-

""

OIR-3-REMOVE

3-Error

Removed [chars] in slot [dec]

Type of card removed from slot

-

""

OIR-3-SUBCARDDETECT

3-Error

Slot [dec] [chars] [dec]: subcard [dec] inserted

Type of card detected in slot\n

-

""

OIR-3-SUBCARDREMOVE

3-Error

Slot [dec] [chars] [dec]: subcard [dec] removed

Type of card removed from slot

-

""

OIR-3- SUBCARD_BAD_IDPROM

3-Error

Slot [dec] [chars] [dec]: subcard [dec] IDPROM not programmed correctly

IDPROM is not programmed correctly

-

"Contact customer support."

OIR-3- SUBCARD_BAD

3-Error

Slot [dec] [chars] [dec]: subcard [dec] does not meet operating specifications

Subcard does not meet operating specifications

-

"Contact customer support."

OIR-3- SUBCARD_BAD_PORT

3-Error

Slot [dec] [chars] [dec]: subcard [dec] did not initialize correctly

Subcard did not initialize correctly

-

"Contact customer support."

OIR-3-OSC_SUBCARDDETECT

3-Error

Slot [dec] [chars] [dec]: subcard [dec] inserted

OSC Subcard detected in slot\n

-

""

OIR-3-OSC_SUBCARDREMOVE

3-Error

Slot [dec] [chars] [dec]: subcard [dec] removed

OSC Subcard removed from slot

-

""

OIR-3-PSM_SUBCARDDETECT

3-Error

Slot [dec] [chars] [dec]: subcard [dec] inserted

PSM Subcard detected in slot\n

-

""

OIR-3-PSM_SUBCARDREMOVE

3-Error

Slot [dec] [chars] [dec]: subcard [dec] removed

PSM Subcard removed from slot

-

""

OIR-3-XCVRDETECT

3-Error

Slot [dec] Subcard [dec] port [dec]: line transceiver inserted

Type of card detected in slot\n

-

""

OIR-3-XCVRREMOVE

3-Error

Slot [dec] Subcard [dec] port [dec]: line transceiver removed

Type of card removed from slot

-

""

OIR-3-SUBCARD_DISC

3-Error

Slot [dec]: [[chars] [dec]] subcards discovery

Discovered subcards in a slot

-

""

OIR-3-SUBCARD_DEACT

3-Error

Slot [dec]: [[chars] [dec]] subcards deactivated

Deactivated subcards in a slot

-

""

OIR-3-DEACTIVATED

3-Error

Slot [dec] [chars] [dec]: subcard [dec] deactivated

Deactivated subcard in a slot

-

""

OIR-3-SUBCARD_SCANERR

3-Error

Error in scanning subcards in slot [dec]

Error in scanning subcards\n

-

""

OIR-3-LINECARD_NOT_READY

3-Error

Line card in slot [dec] not becoming ready after OIR

After OIR Line is not becoming ready\n

-

"Contact customer support."

OIR-3-INVALID_ALERT_FORMAT

3-Error

Invalid LRC alert format received from slot [dec] format [hex]

Invalid LRC alert format\n

-

""

OIR-3-INVALID_ALERT_COMBINATION

3-Error

Invalid alert combination received with lrc version [dec] src version [dec]

Invalid LRC alert combination\n

-

""

OIR-3-INVALID_OPER_TYPE

3-Error

Invalid operation on slot [dec] op_type [hex]

Invalid operation type from SRC/LRC\n

-

""

OIR-3-RF_REGISTRTN_FAILED

3-Error

OIR Client failed to register with RF

Due to some error OIR Client Failed to register with the RF

-

"Contact customer support."

METOPT-3-NOACK

3-Error

Access to [chars] temperature sensor failed

Accesses to chassis temperature sensor failed.

-

LOG_STD_SH_TECH_ACTION

METOPT-3-IDPROM_MISMATCH

3-Error

Mismatch in backplane IDPROM [chars]: Active-side=[dec] Sby-side=[dec]

There are two backplane IDPROMS. Each is readable by one of the two redundant CPUs. Most IDPROM fields should be programmed by manufacturing to contain identical information. Only the first mismatched field is shown. Use a CLI show command to see additional mismatches.

-

LOG_STD_SH_TECH_ACTION

METOPT-3-IDPROM_STR_MISMATCH

3-Error

Mismatch in backplane IDPROM [chars]: Active-side=[chars] Sby-side=[chars]

There are two backplane IDPROMS. Each is readable by one of the two redundant CPUs. Most IDPROM fields should be programmed by manufacturing to contain identical information. Only the first mismatched string is shown. Use a CLI show command to see additional mismatches.

-

LOG_STD_SH_TECH_ACTION

METOPT_DI-3-INTERNAL_ERROR

3-Error

[chars][dec]:[chars]

The Metro Optical CDL defect indiation subsystem encountered\n\ an internal software error. The error message contains text\n\ useful to identify the nature of the problem.

-

LOG_STD_SH_TECH_ACTION

METOPT_DI-1-ALARM

1-Alert

[chars]:[chars]

The specified alarm has occured or cleared

-

"The recommeded action is to repair the source of the alarm."

SRC-3-LC_REG_READ_FAIL

3-Error

Register read failed for slot [dec] addr 0x[hec] due to [chars]

SRC unable to read line card register

-

LOG_STD_ACTION

SRC-3-LC_REG_WRITE_FAIL

3-Error

Register write failed for slot [dec] addr 0x[hec] due to [chars]

SRC unable to write line card register

-

LOG_STD_ACTION

SRC-3-LC_CMI_INTF_FAULT

3-Error

SRC detected a CMI interface fault for line card in slot [dec]

SRC detected a CMI interface fault

-

LOG_STD_ACTION

SRC-3-LC_APS_INTF_FAULT

3-Error

SRC detected a APS interface fault for line card in slot [dec]

SRC detected a APS interface fault

-

LOG_STD_ACTION

SRC-3-LC_APS_INTF_INIT_FAULT

3-Error

SRC-LRC APS interface could not be initialized for line card in slot [dec]

SRC detected a APS interface fault

-

LOG_STD_ACTION

SRC-3-LC_APS_TIMEOUT

3-Error

SRC detected keep alive timeout on APS intferace for slot [dec]

SRC detected a APS keep alive timeout fault

-

LOG_STD_ACTION

SRC-3-LC_CMI_TIMEOUT

3-Error

SRC detected keep alive timeout on CMI intferace for slot [dec]

SRC detected a CMI keep alive timeout fault

-

LOG_STD_ACTION

SRC-3-AFOVEN_ERROR

3-Error

Attempt to enable [chars] protection autofailover on interface [chars] when port status is [hec]

Software attempt at enabling autofailover port status is not good

-

LOG_STD_ACTION

SLOT_SYNC -2-INITSYS

2-Critical

[chars]

A software error occurred during initialization of the Interface Sync RF subsystem

-

"Check for sufficient processor memory." LOG_STD_ACTION

SLOT_SYNC-3-TRANSMIT_ERROR

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to msg translation

-

LOG_STD_ACTION

SLOT_SYNC-3-NO_BUFFER

3-Error

Unable to transmit message type [dec] from [chars]

A transmit error occurred while sending msg to other CPU due to non-availability of buffer

-

LOG_STD_ACTION

SLOT_SYNC-3-UNKNOWN_MSG

3-Error

Unknown message type 0x[hec] received by [chars]

An unknown message type was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

SLOT_SYNC-3-SEND_BAD_SUBCARD_COUNT

3-Error

Sending a slot sync message with subcard count as [dec] for slot [dec]

A slot sync message with bad subcard count is being sent

-

LOG_STD_ACTION

SLOT_SYNC-3-RECV_BAD_SUBCARD_COUNT

3-Error

Received a slot sync message with subcard count as [dec] for slot [dec]

A slot sync message with bad subcard count is being recvd

-

LOG_STD_ACTION

SLOT_SYNC-3-INVALID_MSG

3-Error

Incorrectly formatted message 0x[hec] 0x[hec] received by [chars]

Inconsistent message data was received from the peer CPU possibly due to an incompatible image version.

-

LOG_STD_ACTION

SLOT_SYNC-5-UNSUPPORTED_MSG

5-Notice

Msgtype [chars] sent by [chars] unsupported by peer.

Peer responded that it didn't recognize a message sent by this CPU possibly due to a different image version.

-

"May require a software upgrade on the Standby CPU. " LOG_STD_ACTION

BPE-3-NULL_IDB

3-Error

Null idb pointer [[chars]:[hec]]

Interface pointer is not initialized

-

LOG_STD_ACTION

BPE-3-NOT_REGISTERED

3-Error

Interface[[chars]] MAC is not registered

Interface registration with BPE driver is missing

-

LOG_STD_ACTION

BPE-3-INVALID_PORT

3-Error

Port number[[dec]] is not valid

Port number is invalid

-

LOG_STD_ACTION

BPE-3-INVALID_SLOT

3-Error

Slot number[[dec]] is not valid

Slot number is invalid

-

LOG_STD_ACTION

BPE-3-INVALID_MAC

3-Error

Invalid MAC for slot [[dec]/[dec]/[dec]]

Could not get proper MAC address for a given slot/subcard/port

-

LOG_STD_ACTION

BPE-3-INVALID_IDB_TYPE

3-Error

Invalid IDB type passed [[dec] - [chars]]

Idb type passed is not supported by this function

-

LOG_STD_ACTION

BPE-3-MALLOC_FAILURE

3-Error

Malloc Failed [[chars]]

Could not allocate memory

-

LOG_STD_ACTION

LCMDC-3-PORT_CREATE_FAILED

3-Error

Port Creation Failed [[chars]]

Port data structure creation/initialization failed

-

LOG_STD_ACTION

LCMDC-3-INTF_CREATE_FAILED

3-Error

Interface Create Failed [[chars]]

Interface data structure creation/initialization failed

-

LOG_STD_ACTION

LCMDC-3-INTF_DELETE_FAILED

3-Error

Interface Delete Failed [[chars]]

Interface data structure deletion failed

-

LOG_STD_ACTION

HUJR-3-RDWRFAIL

3-Error

Read/write failed [[chars]]

A read/write error occurred when accessing the hardware

-

LOG_STD_ACTION

LCMDC-3-RDWRFAIL

3-Error

Read/write failed [[chars]]

A read/write error occurred when accessing the hardware

-

LOG_STD_ACTION

LCMDC-3-WLENCKFAIL

3-Error

Unexpected trunk laser wavelength: [chars]

Trunk laser wavelength is incorrect

-

LOG_STD_ACTION

LCMDC-3-IDPROMRDFAIL

3-Error

IDPROM read failed [[chars]].\n \tThe card may not be inserted correctly. Please ensure that card is\n \tinserted completely and then please fasten the screws completely.

The read error occurred when accessing the IDPROM

-

LOG_STD_ACTION

LCMDC-3-IDPROMCRCFAIL

3-Error

IDPROM CRC check failed [[chars]]

CRC check failed for IDPROM

-

LOG_STD_ACTION

LCMDC-3-IDPROMMATCHFAIL

3-Error

IDPROM mismatch read failed [[chars]]

check with catched value fail

-

LOG_STD_ACTION

LCMDC-3-INTRPENDING

3-Error

Pending unexpected interrupt [addr [hex] = [hex]]

One or more pending unexpected interrupts

-

LOG_STD_ACTION

LCMDC-3-PORTFAILASSERTED

3-Error

Unexpected portfail asserted

One or more unexpected portfails asserted

-

LOG_STD_ACTION

LCMDC-3-READYPRESENT

3-Error

Card [slot [dec]] present but not ready

Egress side switch failed to switch position during auto-failover

-

LOG_STD_ACTION

LCMDC-3-TK_WDEVIATION_ALM

3-Error

Trunk Laser wavelength deviation: [chars]

Trunk laser wavelength deviation

-

LOG_STD_ACTION

LCMDC-3-TK_WDEGRADE_ALM

3-Error

Trunk laser degrade: [chars]

Trunk laser wavelength degrade

-

LOG_STD_ACTION

LCMDC-3-EOP_NOLG_ALM

3-Error

Egress Loss of Light: [chars]

Egress side No Light

-

LOG_STD_ACTION

LCMDC-3-STDBYOP_NOLG_ALM

3-Error

Loss of Light on Standby: [chars]

Ingress SONET BIP error count threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-EOP_NOLG_PALM

3-Error

Egress Loss of Light Prealarm: [chars]

CDL Drop FIFO Overflow Prealarm

-

LOG_STD_ACTION

LCMDC-3-MIB_ECDRLK_ALM

3-Error

Egress CDR Locking error [chars] [chars] [chars]

CDR is having trouble locking onto the signal.

-

LOG_STD_ACTION

LCMDC-3-MIB_ESERDESLK_ALM

3-Error

Egress Serdes Locking error [chars] [chars] [chars]

Serdes has trouble locking onto the signal

-

LOG_STD_ACTION

LCMDC-3-MIB_ESERPHERR_ALM

3-Error

Egress Serdes Phase Error [chars] [chars] [chars]

Serdes has a phase error.

-

LOG_STD_ACTION

LCMDC-3-MIB_EOP_NOLG_ALM

3-Error

Egress Loss of Light [chars] [chars] [chars]

Egress side No Light

-

LOG_STD_ACTION

LCMDC-3-MIB_EOP_TKSW_ALM

3-Error

Egress Trunk Switch Mech. Failure [chars] [chars] [chars]

Egress side switch failed to switch position during auto-failover

-

LOG_STD_ACTION

LCMDC-3-MIB_TK_WDEVIATION_ALM

3-Error

Trunk Laser wavelength deviation: [chars] [chars] [chars]

Trunk laser wavelength deviation

-

LOG_STD_ACTION

LCMDC-3-MIB_TK_WDEGRADE_ALM

3-Error

Trunk laser degrade: [chars] [chars] [chars]

Trunk laser wavelength degrade

-

LOG_STD_ACTION

LCMDC-3-MIB_LN_TX_ALM

3-Error

Line Laser Failure [chars] [chars] [chars]

Laser failure

-

LOG_STD_ACTION

LCMDC-3-MIB_GE_ELOSY_ALM

3-Error

Egress GE Loss of Sync [chars] [chars] [chars]

GE Loss of Syncronization error

-

LOG_STD_ACTION

LCMDC-3-MIB_FH_ELOSY_ALM

3-Error

Egress FC/ESCON Loss of Sync [chars] [chars] [chars]

Fiber Channel/ESCON Syncronization error

-

LOG_STD_ACTION

LCMDC-3-MIB_SH_ELOF_ALM

3-Error

Egress SONET Loss of Frame [chars] [chars] [chars]

SONET Loss of Frame error

-

LOG_STD_ACTION

LCMDC-3-MIB_GE_ECETX

3-Error

Egress GE Line Code Err count [chars] [chars] [chars]

GE Line Code error count exceeded threshold

-

LOG_STD_ACTION

LCMDC-3-MIB_FH_ECETX_ALM

3-Error

Egress Fiber Channel/ESCON Line Err [chars] [chars] [chars]

Fiber Channel/ESCON Line code error count exceeded threshold

-

LOG_STD_ACTION

LCMDC-3-MIB_SH_EBIP_ALM

3-Error

Egress SONET BIP Err count [chars] [chars] [chars]

SONET BIP Err count exceeded threshold

-

LOG_STD_ACTION

LCMDC-3-MIB_SH_ESEF_ALM

3-Error

Egress SONET SEF Prealarm [chars] [chars] [chars]

Egress SONET Severely Errored Frame threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-MIB_CDL_HEC_ALM

3-Error

CDL HEC Err count [chars] [chars] [chars]

CDL HEC error count threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-MIB_ICDRLK_ALM

3-Error

Ingress CDR Locking error [chars] [chars] [chars]

Ingress CDR failed to lock onto signal

-

LOG_STD_ACTION

LCMDC-3-MIB_ISERDESLK_ALM

3-Error

Ingress Serdes Locking Error [chars] [chars] [chars]

Ingress Serdes signal lock error

-

LOG_STD_ACTION

LCMDC-3-MIB_ISERPHERR_ALM

3-Error

Ingress Serdes Phase error [chars] [chars] [chars]

Ingress Serdes out of Phase error

-

LOG_STD_ACTION

LCMDC-3-MIB_IOP_NOLG_ALM

3-Error

Ingress Loss of Light [chars] [chars] [chars]

Loss of Light

-

LOG_STD_ACTION

LCMDC-3-MIB_TK_TX_ALM

3-Error

Transmit Failure [chars] [chars] [chars]

Transmit failure

-

LOG_STD_ACTION

LCMDC-3-MIB_TK_TX_LDGR

3-Error

Laser Degrade Trunk side [chars] [chars] [chars]

Laser Degrade failure on the transmit side

-

LOG_STD_ACTION

LCMDC-3-MIB_TK_TX_WD

3-Error

Wavelength Deviation [chars] [chars] [chars]

Wavelength deviation error

-

LOG_STD_ACTION

LCMDC-3-MIB_GE_ILOSY_ALM

3-Error

Ingress GE Loss of Sync [chars] [chars] [chars]

Ingress GE Loss of the Syncronization

-

LOG_STD_ACTION

LCMDC-3-MIB_FH_ILOSY_ALM

3-Error

Ingress FC/ESCON Loss of Sync [chars] [chars] [chars]

Ingress Fiber Channel/ESCON Loss of Syncronization

-

LOG_STD_ACTION

LCMDC-3-MIB_SH_ILOF_ALM

3-Error

Ingress SONET Loss of Frame [chars] [chars] [chars]

Ingress SONET Loss of frame

-

LOG_STD_ACTION

LCMDC-3-MIB_GH_ICETX_ALM

3-Error

Ingress GE Line Code Err [chars] [chars] [chars]

Ingress Line Code error count threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-MIB_FH_ICETX_ALM

3-Error

Ingress FC/ESCON Line Code err [chars] [chars] [chars]

Ingress FC/ESCON Line code error count threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-MIB_SH_ISEF_ALM

3-Error

Ingress SONET SEF [chars] [chars] [chars]

Ingress SONET Severely Errored Frame threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-MIB_SH_IBIP_ALM

3-Error

Ingress SONET BIP error [chars] [chars] [chars]

Ingress SONET BIP error count threshold exceeded

-

LOG_STD_ACTION

LCMDC-3-MIB_EOP_NOLG_PALM

3-Error

Egress Loss of Light Prealarm [chars] [chars] [chars]

-

-

LOG_STD_ACTION

LCMDC-3-MIB_TK_OFC_IND

3-Error

Trunk OFC IND [chars] [chars] [chars]

Egress OFC Indication

-

LOG_STD_ACTION

LCMDC-3-MIB_LN_OFC_IND

3-Error

Line OFC IND [chars] [chars] [chars]

Ingress OFC Indication

-

LOG_STD_ACTION

LCMDC-3-MIB_CDL_RFOF_IND

3-Error

CDL Drop FIFO OvrFL [chars] [chars] [chars]

CDL Drop FIFO Overflow Prealarm

-

LOG_STD_ACTION

LCMDC-3-ACCESS_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-FPGA_ACCESS_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-IDPROM_ACCESS_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-ETH_DCC_LPBK_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-INT_LPBK_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-LPBK_THRU_PSC_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-OPT_SWITCH_0_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-OPT_SWITCH_1_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-OPT_SWITCH_2_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-OPT_SWITCH_3_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-OSC_HW_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-LASER_DEGRADE

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-LASER_DEVIATION

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-LINE_LASER_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-TRUNK_LASER_DEGRADE

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-TRUNK_LASER_DEVIATION

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-WAVELENGTH_MISMATCH

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-WAVELENGTH_DEVIATION

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-MDSUBCARD_IDPROM_FAIL

3-Error

Alarm: [chars] [chars] [chars] [chars] [chars]

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

LCMDC-3-INVALIDCLKRATE

3-Error

Non supported clock rate [dec] Khz

The entered clock rate in Khz is not supported

-

LOG_STD_ACTION

LCMDC-3-INVALIDSIGRATE

3-Error

Non supported signal rate [dec]

The entered enum signal rate is invalid

-

LOG_STD_ACTION

LCMDC-4-RATEMISMATCH

4-Warning

Encap rate mismatched: [chars]

The entered encap rate is not matched with xcvr type

-

LOG_STD_ACTION

LCMDC-5-DEFWAVELEN

5-Notice

Default wavelength selected: [chars]

The inserted transponder can not support cached hwsb->itu_num so the default wavelength is used instead

-

LOG_STD_NO_ACTION

LCMDC-3-DEBUG_INTF_CREATE_FAILED

3-Error

Transparent Interface Creation Failed for slot [[dec]]

Interface data structure creation/initialization failed

-

LOG_STD_ACTION

LCMDC-3-LRCMAGICREGRESET

3-Error

Magic Register Reset Slot [dec]

Magic Register Reset for Linecard in slot

-

LOG_STD_ACTION

METOPT_DRV-3-TP_INTERNAL_ERROR

3-Error

[chars][dec]:[chars] [dec]

The Metro Optical Transponder driver subsystem encountered\n\ an internal software error. The error message contains text\n\ useful to identify the nature of the problem.

Xponder

"Please verify whether the Interface exists in the\n\ system. If the card is OIR'ed or EOIR is done then we will see\n\ such NULL strings in the system.Ensure that the interface exists in\n\ the system"

METOPT_DRV-3-REPROGRAM_ERROR

3-Error

[chars]\n

The Metro Optical Reprogram driver encountered\n\ an error. The error message contains text\n\ useful to identify the nature of the problem.

Reprogram

"Retry the reprogram of the card. If the reprogram fails again remove the card and reinsert it. If the card does not come up save the console log and contact Cisco TAC for further assistance."

LCMDC-6-TX_ALARM_SOAK

6-Information

[chars]\n

Submit An alarm - Prints out descriptive message

-

LOG_STD_ACTION

XCVR-3-UNKNOWN_SFP_INSERTED

3-Error

Unknown SFP inserted [chars]

Unknown SFP inserted

-

LOG_STD_ACTION

SFP_SECURITY-4-UNRECOGNIZED_VENDOR

4-Warning

SFP interface [chars] manufactured by an unrecognized vendor

The SFP was identified as a Cisco SFP but the system was unable to match its manufacturer with one on the known list of Cisco SFP vendors

firmware

"Check the list of supported SFPs for this version " "of the system software. An upgrade may be required " "for newer SFPs."

SFP_SECURITY-4-VN_DATA_CRC_ERROR

4-Warning

SFP interface [chars] has bad crc

The SFP was identified as a Cisco SFP but it does not have valid crc in the eeprom data.

firmware

"Check the list of supported SFPs for this version " "of the system software. An upgrade may be required " "for newer SFPs. Even if unrecognized the SFP " "may still operate properly perhaps with limited " "functionality."

SFP_SECURITY-4-ID_MISMATCH

4-Warning

Identification check failed for SFP interface [chars]

The SFP was identified as a Cisco SFP but the system was unable to verify its identity

firmware

"Check the list of supported SFPs for this version " "of the system software. An upgrade may be required " "for newer SFPs. Otherwise verify that the SFP " "was obtained from Cisco or a supported vendor"

SFP_SECURITY-4-DUPLICATE_SN

4-Warning

SFP interface [chars] has the same serial number as another SFP interface

The SFP was identified as a Cisco SFP but its serial number matches that of another interface on the system.

firmware

"Cisco SFPs are assigned unique serial numbers. " "Verify that the SFP " "was obtained from Cisco or a supported vendor"

SFP_SECURITY-4-SFP_INTERR

4-Warning

Internal error occurred in setup for SFP interface [chars]

The system could not allocate resources or had some other problem in the setup for the specified SFP interface.

firmware

"Reload the system. If the problem persists " "contact TAC."

ETHER_CFM-3-CROSS_CONNECTED_CSI

3-Error

Service ID of received CC [chars] does not match local Service ID [chars].

For a given service within a domain the Service ID in the CC message should match the locally configured Service ID.

ethernet-cfm

"Verify that the service ID's are configured correctly using 'show ethernet cfm " "domain. "

ETHER_CFM-3-RCV_LOCAL_MPID

3-Error

MPID of CC matches local MPID.

The remote MPID matches a MPID configured locally for the service.

ethernet-cfm

"Either the local MPID or remote MPID should be changed as the MPID " " should be unique for a given service in a network"

ETHER_CFM-3-MEP_NOT_CONFIGURED

3-Error

received CC from unconfigured remote MEP.

While performing cross check a CC message was received from a remote MEP which is not configured under the domain submode.

ethernet-cfm

"Verify if the remote MEP should be added to the remote MEP list under the domain" " using 'show ethernet cfm domain."

ETHER_CFM-3-LR_FROM_WRONG_FP

3-Error

received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination

An unknown destination sent a reply to a Loopback messages that was intended to another device.

ethernet-cfm

"Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message."

ETHER_CFM-3-TM_EGRESS_BOUNDRY

3-Error

egress path found for TM is at a higher level than the traceroute message.

Traceroute found a domain boundry on egress since the egress port level is higher than the Traceroute Message level.

ethernet-cfm

"Check if the MIP level on the egress port is at appropriate level."

ETHER_CFM-6-ENTER_LCK_INT

6-Information

Interface [chars] enters LCK defect condition for [chars] direction

Interface is put in OOS state through exec cli for input direction

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_LCK_INT

6-Information

Interface [chars] exited LCK defect condition for [chars] direction

Interface has exited LCK defect condition.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-ENTER_LCK

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters LCK defect condition

Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_LCK

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited LCK defect condition

Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-ENTER_AIS_INT

6-Information

Interface [chars] enters AIS defect condition for [chars] direction

Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_AIS_INT

6-Information

Interface [chars] exited AIS defect condition for [chars] direction

LOG_STD_NO_ACTION

ethernet-cfm

"Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state"

ETHER_CFM-6-ENTER_AIS

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters AIS defect condition

Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-EXIT_AIS

6-Information

local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited AIS defect condition

Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep vlan id or bridge-domain id.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-5-IGNORED_VLAN

5-Notice

Ignored VLAN [dec] in '[chars]'

Invalid VLAN was ignored in the configuration.

ethernet-cfm

"LOG_STD_NO_ACTION"

ETHER_CFM-6-REMOTE_MEP_UP

6-Information

Continuity Check message is received from a remote MEP with mpid [dec] [chars] [chars] domain [chars] event code [chars].

A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MAID or CSIID

ethernet-cfm

"Information message only."

ETHER_CFM-3-REMOTE_MEP_DOWN

3-Error

Remote MEP mpid [dec] [chars] [chars] in domain [chars] changed state to down with event code [chars].

The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB

ethernet-cfm

"Check the remote CFM configurations using CFM " " utilities like traceroute and ping."

ETHER_CFM-3-CROSS_CONNECTED_SERVICE

3-Error

Continuity Check message with unmatched [chars] is received from a remote MEP with mpid [dec] [chars] level [dec] domain [chars] MAC: [enet].

The Continuity Check message whose CSIID or MAID is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network.

ethernet-cfm

"Configure the CFM CSI ID properly across the " "network."

ETHER_CFM-3-FORWARDING_LOOP

3-Error

Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the [chars].

The device is receiving its own CC messages for a particular vlan or evc within the same CSI or MA.

ethernet-cfm

"Configure the CFM maintenance points properly " "to avoid the forwarding loop."

ETHER_CFM-3-CONFIG_ERROR

3-Error

CFM miss-configuration in the network. Same mpid [dec] configured within the same maintenance name [chars] having [chars] for [chars].

The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MAID or CSIID.

ethernet-cfm

"Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association."

ETHER_CFM-3-CROSSCHECK_MEP_MISSING

3-Error

The device does not receive any CC messages from a remote MEP with mpid [dec] [chars] that it was expecting to be part of the [chars] in the domain [chars] from MAC: [enet].

The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MAID or CSIID.

ethernet-cfm

"There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. "

ETHER_CFM-3-CROSSCHECK_MEP_UNKNOWN

3-Error

The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the [chars] in the domain: [chars].

The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MAID or CSIID.

ethernet-cfm

"Check whether the CFM crosscheck configurations " "are proper."

ETHER_CFM-6-CROSSCHECK_SERVICE_UP

6-Information

The device received CC messages from all remote MEPs within a given [chars] in the maintenance domain [chars].

The service configured either CSI or MA is up as it receives CC messages from all remote statically configured MEPs.

ethernet-cfm

"Information message only."

ETHER_CFM-3-FAULT_ALARM

3-Error

A fault has occurred in the network for the local MEP having mpid [dec] vlan [dec] [chars] indicating a fault with the event code [chars].

This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEPP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other CSI or MA.

ethernet-cfm

"There could be a possible fault in the network. " "Check whether the cfm configurations are proper."

ETHER_LMI_HA-2-INIT

2-Critical

Ether LMI ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Ether LMI ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ethernet-lmi

LOG_STD_ACTION

ETHER_LMI_HA-3-TRANSFORM

3-Error

Ether LMI ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Ether LMI ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether LMI state between the active device and the standby device is not identical.

ethernet-lmi

"show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_LMI_HA-3-MSG_NOT_OK

3-Error

Ether LMI ISSU client 'Message Type [dec]' is not compatible

The Ether LMI ISSU client received an incompatible message from the peer device. The message cannot be processed.

ethernet-lmi

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_LMI_HA-3-MSG_SIZE

3-Error

Ether LMI ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Ether LMI ISSU client failed to calculate the MTU for the specified message. The Ether LMI ISSU client will not able to send the message to the standby device.

ethernet-lmi

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

ETHER_LMI_HA-3-INVALID_SESSION

3-Error

Ether LMI ISSU client does not have a valid registered session.

The Ether LMI ISSU client does not have a valid registered session.

ethernet-lmi

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_LMI_HA-2-SESSION_REGISTRY

2-Critical

Ether LMI ISSU client failed to register session information. Error: [dec] [chars]

The Ether LMI ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ethernet-lmi

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_LMI_HA-3-SESSION_UNREGISTRY

3-Error

Ether LMI ISSU client failed to unregister session information. Error: [dec] [chars]

The Ether LMI ISSU client failed to unregister session information.

ethernet-lmi

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_LMI_HA-2-SESSION_NEGO

2-Critical

Ether LMI ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Ether LMI ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ethernet-lmi

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ETHER_LMI_HA-2-SEND_NEGO_FAILED

2-Critical

Ether LMI ISSU client failed to send negotiation message. Error: [dec] [chars]

The Ether LMI ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ethernet-lmi

"show logging and show checkpoint client"

ETHER_LMI_HA-2-GET_BUFFER

2-Critical

Ether LMI ISSU client failed to get buffer for message. Error: [dec] [chars]

The Ether LMI HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly.

ethernet-lmi

"show logging and show checkpoint client"

SGBP-3-INVALIDB

3-Error

[chars] for bundle \'[chars]\' -- [chars]

An internal software error has occurred.

-

LOG_STD_ACTION

SGBP-7-NEWL

7-Debug

Local query #[dec] for [chars] count [dec] ourbid [dec]

This message is generated only when SGBP query debugging is\n\ enabled. It provides information about queries in progress.

-

LOG_STD_NO_ACTION

SGBP-7-DUPL

7-Debug

Duplicate local query #[dec] for [chars] count [dec] ourbid [dec]

This message is generated only when SGBP query debugging is\n\ enabled. It provides information about queries in progress.

-

LOG_STD_NO_ACTION

SGBP-7-NEWP

7-Debug

Peer query #[dec] for [chars] count [dec] peerbid [dec] ourbid [dec]

This message is generated only when SGBP query debugging is\n\ enabled. It provides information about queries in progress.

-

LOG_STD_NO_ACTION

SGBP-7-CANCEL

7-Debug

Local query #[dec]:[dec] for bundle [chars]

This message is generated only when SGBP query debugging is\n\ enabled. It provides information about queries in progress.

-

LOG_STD_NO_ACTION

SGBP-7-DONE

7-Debug

Query #[dec] for bundle [chars] count [dec] master is [chars]

This message is generated only when SGBP event debugging is\n\ enabled. It indicates that a peer timed out while closing a\n\ query. The connection has been dropped.

-

"Check the peer equipment and network media for problems."

SGBP-7-MQB

7-Debug

\tBundle: [chars]\tState: [chars]\tOurBid: %03d

This message is part of a list of debug states displayed at the\n\ request of the operator.

-

LOG_STD_NO_ACTION

SGBP-7-PB

7-Debug

\t[inet]\tState: [chars]\tBid: %03d Retry: [dec]

This message is part of a list of debug states displayed at the\n\ request of the operator.

-

LOG_STD_NO_ACTION

SGBP-7-EQUAL

7-Debug

[dec] equal highest bids randomly select bid# [dec]

This message is generated only when SGBP query debugging is\n\ enabled. It provides information about queries in progress.

-

LOG_STD_NO_ACTION

SGBP-7-HANGUP

7-Debug

I am a forward-only member can't forward bundle [chars] hangup

This message is generated only when SGBP query event and/or\n\ error debugging is enabled. This indicates a routine change of\n\ role for the router in its SGBP interactions with its peers.

-

LOG_STD_NO_ACTION

SGBP-3-INVFIELD

3-Error

[chars] field type [hex] has [chars] [dec] expected [dec]

This message indicates that an SGBP request from a peer\n\ contained invalid or corrupt data.

-

"Check the peer equipment or network media for any problems."

SGBP-7-RCVD

7-Debug

MQ [chars] from [inet] for query [dec]:[dec] bundle [chars] bid [dec] prot[chars]

This message is generated only when SGBP message debugging is\n\ enabled. It indicates that an SGBP packet was received.

-

LOG_STD_NO_ACTION

SGBP-7-SENT

7-Debug

MQ [chars] to [inet] for query [dec]:[dec] bundle [chars] bid [dec] prot[chars] len [dec]

This message is generated only when SGBP message debugging is\n\ enabled. It indicates that an SGBP packet was sent.

-

LOG_STD_NO_ACTION

SGBP-3-UNEXP

3-Error

MQ [chars] from [inet] for query [dec]:[dec] bundle [chars] bid [dec] state [chars]

This message is generated only when SGBP error debugging is\n\ enabled. The SGBP connection has entered an unexpected state\n\ possibly due to a software error.

-

LOG_STD_ACTION

SGBP-3-INVALID

3-Error

MQ message with [chars]

This message is generated only when SGBP error debugging is\n\ enabled. An invalid message was received and discarded.

-

"This probably indicates an error in network media or\n\ a peer which is generating erroneous packets."

SGBP-7-MQ

7-Debug

[chars] [hex] for query [dec]:[dec] bundle [chars] bid [dec] len [dec]

This message is generated only when SGBP error debugging is\n\ enabled. This message indicates that an SGBP query has been\n\ received.

-

LOG_STD_NO_ACTION

SGBP-3-PEERERROR

3-Error

Peer [inet] [chars] during \'PB [chars]\' state for bundle [chars]

An internal software error has occurred.

-

LOG_STD_ACTION

SGBP-3-UNKNOWNPEER

3-Error

Event [hex] from peer at [inet]

This message is generated only when SGBP error debugging is\n\ enabled. An SGBP event came from a network host which was not\n\ recognizable as an SGBP peer. The event was discarded.

-

"Check if a network media error could have corrupted the address\n\ or if peer equipment is malfunctioning to generate corrupted\n\ packets.\n\ Depending on the network topology and firewalling SGBP packets\n\ from a non-peer host could indicate probing and attempts to\n\ breach security. If there is a chance your network is under\n\ attack obtain knowledgeable assistance. " LOG_STD_ACTION

SGBP-3-UNKNOWNEVENT

3-Error

Event [hex] from peer at [inet]

This message is generated only when SGBP error debugging is\n\ enabled. An invalid event occurred which probably\n\ indicates an internal software error.

-

"LOG_STD_ACTION"

SGBP-5-SHUTDOWN

5-Notice

[chars]

This message is generated only when SGBP event debugging is\n\ enabled. A process involved in SGBP was terminated\n\ upon completion of its work.

-

LOG_STD_NO_ACTION

SGBP-5-STARTUP

5-Notice

[chars]

This message is generated only when SGBP event debugging is\n\ enabled. An process involved in SGBP was started.

-

LOG_STD_NO_ACTION

SGBP-7-CLOSE

7-Debug

Closing pipe for member [chars]

This message is generated only when SGBP event debugging is\n\ enabled. An interprocess communication link was closed.

-

LOG_STD_NO_ACTION

SGBP-5-ARRIVING

5-Notice

New peer event for member [chars]

This message is generated only when SGBP event debugging is\n\ enabled. An SGBP peer joined the group.

-

LOG_STD_NO_ACTION

SGBP-5-LEAVING

5-Notice

Member [chars] leaving group [chars]

This message is generated only when SGBP event debugging is\n\ enabled. An SGBP peer has left the group.

-

LOG_STD_NO_ACTION

SGBP-3-UNKNOWN

3-Error

[inet] not known

This message is generated only when SGBP error debugging is\n\ enabled. An SGBP connection was attempted by a host which was\n\ not recognized as a peer. The connection was not accepted.

-

"Depending on the network topology and firewalling SGBP connection\n\ attempts from a non-peer host could indicate probing and attempts to\n\ breach security. If there is a chance your network is under\n\ attack obtain knowledgeable assistance. " LOG_STD_ACTION

SGBP-1-AUTHFAILED

1-Alert

Member [chars] failed authentication

This message is generated only when SGBP hellos or errors\n\ debugging is enabled. This indicates that an attempted\n\ peer connection ended in authentication failure. A peer may be\n\ misconfigured. Or this could indicate an attempted security\n\ breach.

-

"Check if the peer is correctly configured.\n\ If there is a chance your network is under attack obtain\n\ knowledgeable assistance. " LOG_STD_ACTION

SGBP-7-CHALLENGED

7-Debug

Rcv Hello Challenge message from member [chars] using [inet]

This message is generated only when SGBP hellos debugging\n\ is enabled. This indicates that an authentication challenge\n\ was received from a peer.

-

LOG_STD_NO_ACTION

SGBP-7-RESPONSED

7-Debug

Rcv Hello Response message from member [chars] using [inet]

This message is generated only when SGBP hellos debugging\n\ is enabled. This indicates that a response to an authentication\n\ challenge was received from a peer.

-

LOG_STD_NO_ACTION

SGBP-7-CHALLENGE

7-Debug

Send Hello Challenge to [chars] group [chars]

This message is generated only when SGBP hellos debugging\n\ is enabled. This indicates that an authentication challenge\n\ was sent to a peer.

-

LOG_STD_NO_ACTION

SGBP-7-RESPONSE

7-Debug

Send Hello Response to [chars] group [chars]

This message is generated only when SGBP hellos debugging\n\ is enabled. This indicates that a response to an authentication\n\ challenge was sent to a peer.

-

LOG_STD_NO_ACTION

SGBP-7-NORESP

7-Debug

Failed to respond to [chars] group [chars] may not have password

An authentication challenge was received but there was no\n\ information available to respond to it. This probably\n\ indicates a configuration error a missing password.

-

"Refer to the documentation to configure a username\n\ with the same name as the SGBP group."

SGBP-1-UNKNOWNHELLO

1-Alert

Rcv Hello message from non-group member using [inet]

This message is generated only when SGBP hellos or error\n\ debugging is enabled. An SGBP Hello message was received\n\ from a host that is not a member of the SGBP group\n\ and discarded.

-

-

SGBP-1-MISSCONF

1-Alert

Possible misconfigured member [chars] using [inet]

This message is generated only when SGBP hellos or error\n\ debugging is enabled. This indicates a configuration error.\n\ Either this router has an incorrect IP address listed for\n\ the peer or the peer is using an incorrect IP address.

-

"Find and correct the configuraton error."

SGBP-7-RCVINFO

7-Debug

Received Info Addr = [inet] Reference = [hex]

This message is generated only when SGBP hellos debugging is enabled.\n\ It indicates that data was received by a listener process.

-

LOG_STD_NO_ACTION

SGBP-7-SENDINFO

7-Debug

Send Info Addr to [chars]

This message is generated only when SGBP hellos debugging is enabled.\n\ It indicates that data was sent by the listener process in response\n\ to received data.

-

LOG_STD_NO_ACTION

SGBP-7-KEEPALIVE

7-Debug

Sending Keepalive to [chars] retry=[dec]

This message is generated only when SGBP hellos debugging is enabled.\n\ It indicates that a keepalive message was send to an SGBP member.

-

LOG_STD_NO_ACTION

SGBP-7-KEEPALIVE_TIMEOUT

7-Debug

Keepalive timeout on [chars]

This message is generated only when SGBP hellos debugging is enabled.\n\ It indicates that keepalive messages were not answered so the pipe\n\ to an SGBP member has been closed.

-

LOG_STD_NO_ACTION

SGBP-7-SENDAUTHOK

7-Debug

Send Hello Authentication OK to member [chars] using [inet]

This message is generated only when SGBP hellos debugging is enabled.\n\ A message was send or re-sent to another SGBP member indicating\n\ that an authentication attempt from that member succeeded.

-

LOG_STD_NO_ACTION

SGBP-7-AUTHOK

7-Debug

Member [chars] State -> AuthOK

This message is generated only when SGBP errors or events\n\ debugging is enabled. A message was received from another SGBP\n\ member indicating that an authentication attempt to that member\n\ succeeded.

-

LOG_STD_NO_ACTION

SGBP-7-WAITINFO

7-Debug

Member [chars] State -> WaitInfo

-

-

-

SGBP-7-ACTIVE

7-Debug

Member [chars] State -> Active

This message is generated only when SGBP errors or events\n\ debugging is enabled. This indicates that a link to another\n\ SGBP member has completed the interactions to set it up and is\n\ now entering the active state.

-

LOG_STD_NO_ACTION

SGBP-1-DIFFERENT

1-Alert

Rcv [chars]'s addr [inet] is different from the hello's addr [inet]

The internally-configured address for an SGBP member does not\n\ match the address of the host that tried to authenticate as\n\ that member. The configuration is incorrect on either this\n\ system or the other member - they must agree.

-

"Determine which configuration is in error and fix it."

SGBP-1-NOTAUTH

1-Alert

Rcv Connection request by non-authenticated member [chars]

-

-

-

SGBP-1-DUPLICATE

1-Alert

Rcv Duplicate bundle [chars] is found on member [chars]

This message is generated only when SGBP hellos or errors\n\ debugging is enabled. This indicates that a duplicate bundle\n\ was received from the same peer more than once. The duplicate\n\ was discarded.

-

LOG_STD_RECUR_ACTION

SGBP-3-INVALIDADDR

3-Error

Stack group [chars] IP address [inet]

The current configuration does not allow a local IP address to be \n\ configured using <cmdBold>sgbp member <address><noCmdBold>. Any\n\ local address is automatically removed fro the SGBP group.

sgbp

"Do not configure <cmdBold>sgbp member <address><noCmdBold> \n\ using a local IP address."

MLRIB-4-TOPOLOGY_ROUTE_LIMIT_REACHED

4-Warning

Route topology scope [dec] has reached its maximum route capacity of [dec]

The number of routes installed in a route scope topology has exceeded a preset limit. This condition indicates a high density of routes within this scope. No more routes can be installed within this scope until the number goes below high water mark of 95% of preset limit

-

"Consider routing some destination via other " "route topology scopes"

MLRIB-4-SYSTEM_ROUTE_LIMIT_REACHED

4-Warning

Routing system [dec] has reached its maximum route capacity of [dec]

The number of routes installed in a routing system has exceeded a preset limit. This condition indicates a high density of routes within this system. No more routes can be installed within this system until the number goes below high water mark of 95% of preset limit

-

"Consider balancing some destinations using " "additional routing devices"

MLRIB-4-TOPOLOGY_ROUTE_HIGHWATER_MARK_REACHED

4-Warning

Route topology scope [dec] has reached its high water mark of [dec]

The number of routes installed in a routing topology scope has exceeded a threshold. This condition indicates a high density of routes within this routing topology scope.

-

"Consider routing some destination via other " "route topology scopes"

MLRIB-4-SYSTEM_ROUTE_HIGHWATER_MARK_REACHED

4-Warning

Route system [dec] has reached its high water mark of [dec]

The number of routes installed in a routing database has exceeded a threshold. This condition indicates a high density of routes within this system.

-

"Consider balancing some destinations using " "additional routing devices"

MLRIB-4-MLRIB_CLIENT1_ROUTE_REPOPULATION_TIME_EXCEEDED

4-Warning

A routing database client id [dec] failed to complete route repopulation: Layer [dec] sub address family [dec] and routing client instances [dec]

Routing database client did not complete route repopulation within the allotted amount of time after a system failover.

ether-infra

"Contact TAC for further investigation of this " "issue and provide them with the following logs: " "show mlrib layer2 log event all show mlrib layer2 " "log error all show mlrib layer2 log trace all " "show mlrib common log event all show mlrib " "common log error all and show logging "

MLRIB-4-MLRIB_CLIENT2_ROUTE_REPOPULATION_TIME_EXCEEDED

4-Warning

A routing database client id [dec] failed to complete route repopulation: Layer [dec] sub address family [dec] and routing client instances [dec]

Routing database client did not complete route repopulation within the allotted amount of time after a system failover.

asr1k-igmpsn

"Contact TAC for further investigation of this " "issue and provide them with the following logs: " "show mlrib layer2 log event all show mlrib layer2 " "log error all show mlrib layer2 log trace all " "show mlrib common log event all show mlrib " "common log error all and show logging "

MLRIB-4-MLRIB_CLIENT3_ROUTE_REPOPULATION_TIME_EXCEEDED

4-Warning

A routing database client id [dec] failed to complete route repopulation: Layer [dec] sub address family [dec] and routing client instances [dec]

Routing database client did not complete route repopulation within the allotted amount of time after a system failover.

isis

"Contact TAC for further investigation of this " "issue and provide them with the following logs: " "show mlrib layer2 log event all show mlrib layer2 " "log error all show mlrib layer2 log trace all " "show mlrib common log event all show mlrib " "common log error all and show logging "

MLRIB-4-MLRIB_CLIENT4_ROUTE_REPOPULATION_TIME_EXCEEDED

4-Warning

A routing database client id [dec] failed to complete route repopulation: Layer [dec] sub address family [dec] and routing client instances [dec]

Routing database client did not complete route repopulation within the allotted amount of time after a system failover.

ios-otv-app

"Contact TAC for further investigation of this " "issue and provide them with the following logs: " "show mlrib layer2 log event all show mlrib layer2 " "log error all show mlrib layer2 log trace all " "show mlrib common log event all show mlrib " "common log error all and show logging "

MLRIB-4-MLRIB_ROUTE_REPOPULATION_TIME_EXCEEDED

4-Warning

All routing database client failed to complete route repopulation

None of the routing database client completed route repopulation within the allotted amount of time after a system failover.

l2rib

"Contact TAC for further investigation of this " "issue and provide them with the following logs: " "show mlrib layer2 log event all show mlrib layer2 " "log error all show mlrib layer2 log trace all " "show mlrib common log event all show mlrib " "common log error all and show logging "

MLRIB-3-MLRIB_L2_ERROR_DELETING_VPN

3-Error

Error deleting private network [dec] information from routing database

This occurs when the information about a private network in the routing database gets corrupted and does not fully match with the expected information of the private network to be deleted.

l2rib

"Consider reconfiguring the private network. If " "the error persists reload the router"

MLRIB-3-MLRIB_L2_ERROR_DELETING_TOPOLOGY

3-Error

Error deleting routing topology scope [dec] information from routing database

This condition occurs when the information about a routing topology scope in the routing database gets corrupted and does not fully match with the expected information of the routing topology to be deleted.

l2rib

"Consider reconfiguring the routing topology scope. " "If the error persists reload the router "

MLRIB-6-MLRIB_L2_PREEMPTIVE_PRIV_NETWORK_NOTIFICATION

6-Information

A notification was sent preemptively for the private network [dec] and client id [dec]

This condition occurs when the client experiences a large number of notifications

-

-

MLRIB-6-MLRIB_REDUNDANCY_PREEMPTIVE_NOTIFICATION

6-Information

A notification was sent preemptively for the private network [dec] and client id % after redundancy switchover

This condition occurs when the client experiences a large number of notifications

-

-

SYSLOG_SERVER-4-NO_CONFIG_CHANGE

4-Warning

No configuration change.

There is no configuration change to the syslog-server

-

""

SYSLOG_SERVER-4-NO_MEM

4-Warning

No memory left.

No memory left.

-

"The System Controller is running very low on\n\ memory."

SYSLOG_SERVER-4-NO_MOBIUS

4-Warning

No syslog file.

No syslog file.

-

""

SYSLOG_SERVER-4-FILE_CORRUPTED

4-Warning

syslog records do not appear to be timestamped.

This may be a result of not turning the service timestamp\n\ command.

-

"Please turn the service timestamps log datetime\n\ command on your router. This will cause the system to timestamp\n\ debugging or logging messages.Use atleast datetime."

SYSLOG_SERVER-4-DUP_FILE

4-Warning

Syslog file [[chars]] exists.

You may have issued a directory name that already exists on the\n\ PCMCIA disk.

-

"Please check to see if the directory name \n\ you supplied already exists on the PCMCIA disk and re-enter\n\ a different one"

SYSLOG_SERVER-3-ILLEGAL_FS

3-Error

Illegal file system [chars].

Illegal file system.

-

""

SYSLOG_SERVER-3-UNKNOWN_NAME

3-Error

Unknown command or device name or unable to find device address.

Unknown command or device name or unable to find device address.

-

""

SYSLOG_SERVER-3-MFS_MAX

3-Error

Failed to add Syslog file [chars] maximum Syslog files [dec].

Exceeded the maximum Syslog files allowed.

-

""

SYSLOG_SERVER-3-OPEN_FILE_ERR

3-Error

Failed to open [chars].[dec] syslog file.

Failed to open a syslog file.One or more of the subfiles may\n\ have been deleted or there is no PCMCIA disk

-

"You may not be having a PCMCIA disk in slot0\n\ on the System Controller. Please check to see if it is not a \n\ PCMCIA Flash. If one or more of the subfiles is missing then\n\ they will be automatically restored when the current file reaches\n\ its capacity and gets archived"

SYSLOG_SERVER-3-CREATE_ERR

3-Error

Failed to create a Syslog file.

Failed to create a Syslog file.

-

"There is probably no PCMCIA disk on slot0\n\ on the System Controller. Please check to see if it is not a\n\ PCMCIA Flash"

SYSLOG_SERVER-3-READ_ERR

3-Error

Failed to read a file.

Failed to read a file.

-

""

SYSLOG_SERVER-3-WRITE_ERR

3-Error

Failed to write a syslog file.

Failed to write a syslog file.

-

""

SYSLOG_SERVER-3-PARSING_ERR

3-Error

Parsing file error.

The Router is not configured to timestamp all the log messages

-

"Please configure your router with appropriate\n\ commands to timestamp the log messages. Eg: service timestamps"

MPOA-3-MPOA_ERROR

3-Error

[chars]

A software error has occurred in the multiprotocol-over-ATM subsystem.

-

LOG_STD_SH_TECH_ACTION

MPOA-5-UPDOWN

5-Notice

[chars]

A multiprotocol-over-ATM entity was brought up or down. This is only a status message.

-

LOG_STD_NO_ACTION

MPOA-3-MPS_ERROR

3-Error

[chars]

\n\ A software error has occurred in the multiprotocol-over-ATM server MPS software.

-

LOG_STD_SH_TECH_ACTION

MPOA-4-MPS_WARNING

4-Warning

[chars]

This is a non-fatal warning from the multiprotocol-over-ATM server MPS software probably the result of an incorrect

-

"Try to determine if a configuration or operator " "error has caused this warning." LOG_STD_RECUR_ACTION

MPOA-6-MPS_INFORMATION

6-Information

[chars]

This is a multiprotocol-over-ATM server MPS

-

LOG_STD_NO_ACTION

MPOA-3-MPC_ERROR

3-Error

[chars]

A software error has occurred in the multiprotocol-over-ATM client MPC software.

-

LOG_STD_SH_TECH_ACTION

MPOA-4-MPC_WARNING

4-Warning

[chars]

This is a non-fatal warning from the multiprotocol-over-ATM client MPC software probably the result of an incorrect

-

"Try to determine if a configuration or operator " "error has caused this warning." LOG_STD_RECUR_ACTION

MPOA-6-MPC_INFORMATION

6-Information

[chars]

This is a multiprotocol-over-ATM client MPC

-

LOG_STD_NO_ACTION

SCCP-0-PANIC

0-Emergency

[chars]

Unrecoverable Internal Panic

sccp

LOG_STD_ACTION

SCCP-1-ALERT

1-Alert

[chars]

A condition that should be corrected immediately.

sccp

LOG_STD_ACTION

SCCP-2-CRITICAL

2-Critical

[chars]

Critical Conditions

sccp

LOG_STD_ACTION

SCCP-3-ERROR

3-Error

[chars]

Errors

sccp

LOG_STD_ACTION

SCCP-4-WARNING

4-Warning

[chars]

Warning

sccp

LOG_STD_ACTION

SCCP-5-NOTICE

5-Notice

[chars]

Notice

sccp

LOG_STD_ACTION

SCCP-6-INFO

6-Information

[chars]

Informational

sccp

LOG_STD_NO_ACTION

MVRP-6-MODECHANGE

6-Information

The operating mode is changed to [chars] mode on interface [chars].

As a result of protocol negotiation the operating mode changed to the specified mode on the specified interface.

mvrp

LOG_STD_NO_ACTION

MVRP-3-ENABLE_FAILED

3-Error

MVRP can't be enabled because [chars]

MVRP can't be enabled for some reason.

mvrp

"Action may be taken according to the given " "reason. If for instance the problem is " "due to lack of memory the user should " "add more memory to his system."

MVRP-3-SUBSYS_INIT_FAILED

3-Error

MVRP subsystem failed in initialization[chars] and MVRP won't

This is extremely unlikely to occur on a customer device. If it does occur the cause is most likely due to the lack of memory so the software failed to create data structures. User should see many

mvrp

"Most likely the system has crashed by then " "if the problem is due to lack of memory. " "If the system miraculously came up then" "user can run <CmdBold>show memory summary" "<NoCmdBold> to check the memory usage. " "Please contact the TAC with the output of " "<CmdBold>show memory summary<NoCmdBold> " "<CmdBold>show version<NoCmdBold> and " "<CmdBold>show run<NoCmdBold> and the " "associated syslog messages from the time " "of the problem."

MVRP-3-HA_INIT_FAILED

3-Error

MVRP High Availability subsystem fails to be initialized and hence MVRP won't support HA stateful switchover.

Either MVRP CF client or MVRP RF client fails to be initialized.

mvrp

"Enter the " "<CmdBold>show redundancy clients<NoCmdBold> " "and <CmdBold>show checkpoint clients<NoCmdBold> to " "find out which client is not initialized."

MVRP-3-ADD_REGISTRY_FAILED

3-Error

MVRP subsystem fails to add callback function [chars]

Other subsystem must have mistakenly add its own callback functions. This syslog is for debugging purpose.

mvrp

LOG_STD_NO_ACTION

MVRP_CONST-3-MAC_MATCH_REG_FAILED

3-Error

Unable to reserve needed MAC match register - cannot run MVRP on interfaces of slot [dec] [chars]

MVRP attempted to reserve a MAC match register for the slot indicated and there is no dedicated register or programmable register available. MVRP cannot be activated on interfaced of this card.

mvrp

"Either conflicting protocols that use the MAC " "match register must be disabled or a different " "card type that supports MVRP must be used."

MVRP_CONST-6-MAC_LEARNING

6-Information

MAC learning on VLAN [chars] is [chars]

MVRP detects network topology change dynamically. If only two MVRP ports are forwarding and not pruned in a VLAN MVRP will disable MAC learning on that VLAN so as to save room in the MAC table which is limited and system-wide resource. This is an informative message. No action needs to be taken.

mvrp

LOG_STD_NO_ACTION

MVRP_CONST-6-MAC_LRN_SETTING_FAILED

6-Information

Failed to [chars] MAC learning on VLAN [chars]

MVRP failed to enable or disable MAC learning on the given VLANs. This is probably due to the fact that MAC learning had already been configured by administrator. Use <CmdBold>show mac-address-table learning<NoCmdBold> to check.

mvrp

LOG_STD_NO_ACTION

MVRP_CONST-6-FEATURE_CONFLICT

6-Information

Failed to enable MVRP on [chars] because conflicting feature [chars] is enabled on the interface

MVRP failed to be enabled on the given interface because of conflicting features. For instance unknown unicast flooding blockingUUFB and MVRP

mvrp

LOG_STD_NO_ACTION

MVRP_ISSU-2-INIT

2-Critical

MVRP ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MVRP ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

mvrp

LOG_STD_ACTION

MVRP_ISSU-3-TRANSFORM_FAIL

3-Error

MVRP ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MVRP ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MVRP state between the active device and the standby device is not identical.

mvrp

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MVRP_ISSU-3-MSG_NOT_OK

3-Error

MVRP ISSU client 'Message Type [dec]' is not compatible

The MVRP ISSU client received an incompatible message from the peer device. The message cannot be processed.

mvrp

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MVRP_ISSU-3-MSG_SIZE

3-Error

MVRP ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MVRP ISSU client failed to calculate the MTU for the specified message. The MVRP ISSU client is not able to send the message to the standby device.

mvrp

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MVRP_ISSU-3-INVALID_SESSION

3-Error

MVRP ISSU client does not have a valid registered session.

The MVRP ISSU client does not have a valid registered session.

mvrp

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVRP_ISSU-2-SESSION_REGISTRY

2-Critical

MVRP ISSU client failed to register session information. Error: [dec] [chars]

The MVRP ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

mvrp

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVRP_ISSU-3-SESSION_UNREGISTRY

3-Error

MVRP ISSU client failed to unregister session information. Error: [dec] [chars]

The MVRP ISSU client failed to unregister session information.

mvrp

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVRP_ISSU-2-SESSION_NEGO

2-Critical

MVRP ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MVRP ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvrp

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVRP_ISSU-2-SEND_NEGO_FAILED

2-Critical

MVRP ISSU client failed to send negotiation message. Error: [dec] [chars]

The MVRP ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvrp

"show logging and show checkpoint client"

MVRP_ISSU-2-GET_BUFFER

2-Critical

MVRP ISSU client failed to get buffer for message. Error: [dec] [chars]

The MVRP ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvrp

"show logging and show checkpoint client"

SIGSM-1-NO_TEMPLATE_ERR

1-Alert

No static template found for slot [dec] port [dec] with parameters provided

The sigsm could not find a matching static template with the same parameters as the controller being used

cas

LOG_STD_ACTION

SIGSM-1-EVENT_ERR

1-Alert

Unexpected event

An error in the signalling state machine

as

LOG_STD_ACTION

SIGSM-1-BAD_VAR_ERR

1-Alert

Out of range variable index [dec] [chars]

There is a fault in a default template or the user has provided a custom template that refers to a variable that is outside the range of cas-custom variables

as

LOG_STD_ACTION

SIGSM-3-NOMEMORY

3-Error

MSG_TRACEBACK|MSG_PROCESS

-

-

-

NAT64-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

nat64

LOG_STD_ACTION

NAT64-3-UNINITIALIZED

3-Error

NAT64 feature is not properly initialized

A function call was made when the system was not properly\n\ initialized.

nat64

LOG_STD_ACTION

NAT64-3-INIT_FAILED

3-Error

An initialization failed rc[chars]

-

-

-

NAT64-3-ENOENT

3-Error

NULL

A lookup failed unexpectedly.

nat64

LOG_STD_ACTION

NAT64-3-EEXIST

3-Error

NULL

An item unexpectedly exists already.

nat64

LOG_STD_ACTION

NAT64-3-ENOMEM

3-Error

Memory allocation failed

A attempt to allocae memory has failed.

nat64

LOG_STD_ACTION

NAT64-3-NAT64_REGISTRY_RC

3-Error

A NAT64 registry call failed with rc[chars]

The return code from a NAT64 registry call indicates an\n\ error.

nat64

LOG_STD_ACTION

NAT64-3-BAD_MAGIC

3-Error

Invalid magic number%#10x

An internal data structure is corrupt.

nat64

LOG_STD_ACTION

NAT64-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

nat64

LOG_STD_ACTION

NAT64-3-RUNAWAY_LOOP

3-Error

NULL

A loop has exceeded the expected number of iterations.

nat64

LOG_STD_ACTION

NAT64-5-ALIAS_NOT_FOUND

5-Notice

Unable to find alias address[inet] table_id[dec]

An attempt was made to remove an IP alias for a NAT64 address and the alias does not exist. This is a notification that such an event happened and should not have any functional impact. This could happen under heavy load if for example a previous best effort message to add the alias was dropped.

nat64

LOG_STD_ACTION

NAT64-6-HA_RELOAD

6-Information

Reloading [chars] reason[chars]

A synchronization attempt between the active and standby RP peers has failed with the reason indicated. The standby peer is reloaded in an attempt to resynchronize when operating in a stateful redundant mode.

nat64

LOG_STD_ACTION

NAT64-6-HA_RELOAD_DISABLED

6-Information

Standby reload has been disabled NAT64 RP state is out of sync and the standby should be reloaded manually

The active and standby RPs are out of sync and the standby RP would have been reloaded but this reload was suppressed based on the configured environment.

nat64

LOG_STD_ACTION

NAT64-6-HA_PEER_READY

6-Information

NULL

The synchronization attempt for the message has determined that the transport has lost communication with its peer. This is a normal situation which indicates that the standby route-processor is currently out of service implying a simplex redundancy mode.

-

-

NAT64-6-HA_FLOW_CTRL_TIMEOUT

6-Information

Bulk sync is flow controlled by [chars]

The bulk synchronization of the NAT64 configuration to the standby RP has encountered a flow control condition which has effected a timeout awaiting the condition to clear. This will result in a reload of the standby RP to allow the bulk synchronization to restart.

nat64

LOG_STD_ACTION

NAT64-6-MAP_E

6-Information

NULL

An unexpected input value to a function was incorrect

nat64

LOG_STD_ACTION

NAT66-3-EINVAL

3-Error

NULL

An unexpected input value to a function was incorrect

nat66

LOG_STD_ACTION

NAT66-3-UNINITIALIZED

3-Error

NAT66 feature is not properly initialized

A function call was made when the system was not properly\n\ initialized.

nat66

LOG_STD_ACTION

NAT66-3-INIT_FAILED

3-Error

An initialization failed rc[chars]

-

-

-

NAT66-3-ENOENT

3-Error

NULL

A lookup failed unexpectedly.

nat66

LOG_STD_ACTION

NAT66-3-EEXIST

3-Error

NULL

An item unexpectedly exists already.

nat66

LOG_STD_ACTION

NAT66-3-ENOMEM

3-Error

Memory allocation failed

A attempt to allocae memory has failed.

nat66

LOG_STD_ACTION

NAT66-3-NAT66_REGISTRY_RC

3-Error

A NAT66 registry call failed with rc[chars]

The return code from a NAT66 registry call indicates an\n\ error.

nat66

LOG_STD_ACTION

NAT66-3-BAD_MAGIC

3-Error

Invalid magic number%#10x

An internal data structure is corrupt.

nat66

LOG_STD_ACTION

NAT66-3-API_FAILED

3-Error

NULL

A call to the API of another component has indicated an\n\ error.

nat66

LOG_STD_ACTION

NAT66-3-RUNAWAY_LOOP

3-Error

NULL

A loop has exceeded the expected number of iterations.

nat66

LOG_STD_ACTION

NETWORK_CLOCK_SYNCHRONIZATION-4-NETCLK_FAIL

4-Warning

Active network clock source [chars] priority [dec] failure

This warning message indicates that there has been a failure of active clock source

PI-netclk

"No action required"

NETWORK_CLOCK_SYNCHRONIZATION-6-NETCLK_ACTIVE

6-Information

Active network clock source is [chars] priority [dec]

This indicates the presence of an active network clock along with its priority

PI-netclk

"This is an informational message only no action required."

NETFLOWLITE-4-NETFLOWLITE_CONNECTORTYPE_UPDATE

4-Warning

Netflow-Lite monitor configuration is not compatible with connector type on interface [chars] [chars]

A new interface connector type has been detected it is not\n\ compatible with the netflow-lite monitor configuration on the\n\ original interface. The conflicting netflow-lite monitor\n\ configuration will be removed no user action is required.

netflow-lite

LOG_STD_NO_ACTION

NP-3-NOTMSGID

3-Error

Message Id [hec] not supported.

The Nextport does not supported this control message id.

as

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NP-3-MODNOTEXIST

3-Error

Slot [dec] DFC [dec] Module [dec] not exist.

No Virtual Console opens for this module.

as

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NP-3-QUEUEFULL

3-Error

[chars] queue is full for Slot [dec] DFC [dec] Module [dec].

TX queue is full for this module.

as

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NP-3-NAKRSP

3-Error

NAK Response Received - command 0x[hec] result code 0x[hec] msg id 0x[hec] session id 0x[hec] msg tag 0x[hec]

A NAK response was sent by the NextPort module.

as

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

NP-3-CTRL_POOL_CREATION_FAIL

3-Error

Control buffer pool could not be created

NextPort driver could not create the control buffer pool required for tx and rx of NP control messages

as

LOG_STD_ACTION

NP_MM-3-INVALID_NPADDRESS

3-Error

Invalid NP_ADDRESS [dec]/[dec]/[dec]/[dec] - [chars]

NextPort Module Manager detected invalid NP_ADDRESS

-

LOG_STD_ACTION

NP_MM-3-MEM_ERR

3-Error

Failed to allocate control message buffer for NP module [dec]/[dec]/[dec] - [chars]

NextPort Module Manager failed to allocate control message buffer

-

LOG_STD_ACTION

NP_MM-3-SEND_FAILED

3-Error

Failed to send [chars] message to NP module [dec]/[dec]/[dec]

NextPort Module Manager failed to send control message

-

LOG_STD_ACTION

NP_MM-3-DATA_Q_FAILED

3-Error

Failed to create Data Q for NP module [dec]/[dec]/[dec]

NextPort Module Manager failed to create Data Queue

-

LOG_STD_ACTION

NP_MM-3-INVALID_STATE

3-Error

Invalid NP module state[chars] [dec]/[dec]/[dec] - [chars]

NextPort Module Manager detected invalid NP module state

-

LOG_STD_ACTION

NP_MM-3-RUNTIME_ERR

3-Error

Module Run Time Error [dec]/[dec]/[dec] : recovery = 0x[hec] error = 0x[hec]

NextPort Module Manager received a module run time error

-

LOG_STD_ACTION

NP_MM-3-INVALID_RSP

3-Error

Unsupported module response [dec]/[dec]/[dec]: msg len = [dec] session ID = [dec] msg tag = [dec] msg ID = [dec]

NextPort Module Manager received an unsupported message response

-

LOG_STD_ACTION

NP_MM-3-INVALID_ACK_RSP

3-Error

Unsupported module ACK response [dec]/[dec]/[dec]: msg len = [dec] session ID = [dec] msg tag = [dec] msg ID = [dec] cmd msg ID = [dec] result code = [dec]

NextPort Module Manager received an unsupported message response

-

LOG_STD_ACTION

NP_MM-3-MODULE_CRASH

3-Error

Module Crash detected [dec]/[dec]/[dec]: state = [dec] cause code = [dec]

NextPort Module Manager detected a crashed module

-

LOG_STD_ACTION

NP_MM-3-RESTART_EXCEEDED

3-Error

Module exceeded restart threshold [dec]/[dec]/[dec]

NextPort Module exceeded the restart threshold

-

LOG_STD_ACTION

NP_MM-3-COUNTRY_CODE_FAILURE

3-Error

Module country code failure [dec]/[dec]/[dec]

NextPort Module Manager failed to set the country code

-

LOG_STD_ACTION

NP-3-RESET_DFC

3-Error

DFC Reset-Cleared Failed - DFC [dec]

DFC Reset-Cleared Failed

as

LOG_STD_ACTION

NP_MD-6-SLOT_INSERTED

6-Information

Slot [dec] [dec] ports max inserted

NextPort Modem driver detected a slot being inserted in the system.\n\ During the startup all slots that are present in the system are treated\n\ as being inserted

-

LOG_STD_NO_ACTION

NP_MD-6-SLOT_REMOVED

6-Information

Slot [dec] removed

Slot has been removed from the system

-

LOG_STD_NO_ACTION

NP_MD-6-MODULE_UP

6-Information

NextPort module [dec]/[dec]/[dec] up

NextPort Modem Driver detected a module coming up

-

LOG_STD_NO_ACTION

NP_MD-6-MODULE_DOWN

6-Information

NextPort module [dec]/[dec]/[dec] down

NextPort Modem Driver detected a module going down

-

LOG_STD_NO_ACTION

NP_MD-0-SLOT_ALREADY_PRESENT

0-Emergency

Slot [dec] is already present in the system

An internal software error occured that possibly resulted in corrupted\n\ slot database.

as

LOG_STD_ACTION

NP_MD-0-NO_SUCH_SLOT

0-Emergency

Slot [dec] is not present in the system

An internal software error occured that possibly resulted in corrupted\n\ slot database.

as

LOG_STD_ACTION

NP_MD-0-NO_SUCH_MODEM

0-Emergency

Attempt to [chars] a data channel on the unexisting modem [dec]/[dec]

An internal software error occured that probably resulted in corrupted\n\modem database

as

LOG_STD_ACTION

NP_MD-0-NO_SUCH_LINE

0-Emergency

Attempt to [chars] a data channel on the unexisting line [dec]/[dec]

An internal software error occured that probably resulted in corrupted\n\ modem database

as

LOG_STD_ACTION

NP_MD-3-BADENCAP

3-Error

Unknown encapsulation [dec] on interface [chars]

A software error occurred resulting in an unknown encapsulation\n\ type on the interface specified by the error message.

as

LOG_STD_ACTION

NP_MD-0-NOMEMORY

0-Emergency

Cannot allocate [dec] bytes of memory for [chars]

The system failed to allocate an important data structure due\n\ to the lack of memory

as

"show mem"

NP_MD-0-NOTTYS

0-Emergency

Cannot allocate TTY[dec] [dec]/%02d

Allocation of TTY structure failed. Either there is not enough memory\n\ or the TTY number is too big

as

LOG_STD_ACTION

NP_MD-0-NOHWIDBS

0-Emergency

Cannot allocate interface Async[dec]/%02d

Allocation of interface structure failed. Either there is not\n\ enough memory or the maximum number of interfaces was exceeded

as

LOG_STD_ACTION

NP_MD-0-NOPAKS

0-Emergency

TTY [chars]: Cannot allocate [chars]

An important buffer cannot be allocated due to the shortage of packet\n\ memory.

as

LOG_STD_ACTION

NP_MD-3-TXQUEUE_EMPTY

3-Error

TTY [chars]: No buffers available to set up the transmit queue

A software error occurred resulting in an invalid state for the\n\ RTS modem signal

as

LOG_STD_ACTION

NP_MD-3-UNKNOWN_INBAND

3-Error

TTY [chars]: Unknown NextPort in-band message msg_id %04x received

NextPort Modem driver received an unknown message from a NextPort module.\n\This can happen if new firmware is used with an obsolete version of IOS

as

LOG_STD_ACTION

NP_MD-1-UNKNOWN_ESCAPE_CHAR

1-Alert

TTY [chars]: Attempt to set an unknown special character type [dec]

NextPort Modem Driver received a request for hardware detection of an\n\ unknown type of a special character due to an internal software error

as

LOG_STD_ACTION

NP_MD-3-CONTIGUOUS

3-Error

Contiguous packet sent for transmit

A software error occurred resulting in an unexpected packet being\n\ set up for transmission and the packet was dropped by the NextPort \n\ Modem Driver

as

LOG_STD_RECUR_ACTION

NP_MD-3-NOTXPAK

3-Error

Static transmit paktype unavailable

A software structure was found in an unexpected state during\n\ run-time for the indicated modem.

as

LOG_STD_ACTION

NP_MD-3-NO_SEED_BUFFER

3-Error

No buffer to seed data queue for module [dec]/[dec]/[dec]

NextPort Modem Driver could not obtain a buffer whilst trying to\n\ seed the module data queue. Due to packet memory shortage

as

LOG_STD_ACTION

NP_MD-3-SEED_BUFFER_FAIL

3-Error

Could not seed data queue for module [dec]/[dec]/[dec]

NextPort Modem Driver could not seed the data queue with buffers

as

LOG_STD_ACTION

NP_MD-0-NO_MODULE_ELEMENTS

0-Emergency

Cannot bring up the module [dec]/[dec]/[dec] due to lack of module elements

NextPort Modem Driver cannot allocate an important data structure called\n\ module element which is necessary to bring up the module. This should\n\ not normally happen and possibly indicates an error condition

async_drivers

LOG_STD_ACTION

NP_MD-3-DATA_QUEUE_SEND_FAIL

3-Error

Could not send to data queue for port [dec] inflight tx buffers [dec]

NextPort Modem Driver could not send buffer to Interface driver

as

LOG_STD_ACTION

NP_MD-3-DATA_CHAN_RX_OVERFLOW

3-Error

Too many buffers [dec] rxd for port [dec]

NextPort Module sent more buffers than is allowed for this channel

as

LOG_STD_ACTION

NP_MD-3-RETURN_DATA_BUFF_FAIL

3-Error

Failed to return data buffer for port [dec]

Call to NextPort Interface Driver to replenish data buffer for this channel failed

as

LOG_STD_ACTION

NP_MD-3-MODEM_SLOT_CREATION_FAIL

3-Error

Modem slot structure for slot [dec] could not be created

NextPort modem driver could not create the modem slot structure which is required for modem services of this card

as

LOG_STD_ACTION

NP_MD-3-TX_INBAND_MSG_FAILURE

3-Error

Failed to send inband message for TTY [chars]

Call to send inband message on data queue failed

as

LOG_STD_ACTION

NP_MD-3-NULL_PTR

3-Error

[chars] is NULL in [chars] for port [dec]

Unexpected NULL pointer at specified location

as

LOG_STD_ACTION

NP_SSM-6-NULL_SSM_INFO

6-Information

NULL SSM Info Handle for slot [dec] port [dec]

NextPort Session and Service Manager failed to obtain a control information handle for the indicated slot and port numbers

-

LOG_STD_ACTION

NP_SSM-6-NULL_VDEV_COMMON

6-Information

NULL Vdev Common Handle for slot [dec] port [dec]

NextPort Session and Service Manager failed to obtain a Voice Device Information handle for the indicated slot and port numbers

-

LOG_STD_ACTION

NP_EST-6-RUNTIME_ERR_NTF

6-Information

[chars]

EST Run-time Error Notification is sent to IOS to convey additional debug data that may help to identify the cause of the error

-

LOG_STD_NO_ACTION

NP_EST-6-DIAG_POST_NTF

6-Information

[chars]

EST Diagnostic/POST Notification is sent to IOS to convey additional information about the power-on self-test or a diagnostic test result

-

LOG_STD_NO_ACTION

NP_EST-6-CTRL_NAK_RSP

6-Information

[chars]

EST Control No-Acknowledge Notification is sent to IOS to convey additional debug data regarding a NAK that occurred on the Control Queue

-

LOG_STD_NO_ACTION

NP_EST-3-MSG_ERR

3-Error

[chars]

EST detected an internal error

-

LOG_STD_NO_ACTION

NP_BS-3-INITSYS

3-Error

[chars]

Failed NextPort BootStrap and Crash Monitor Initialization.

-

LOG_STD_ACTION

NP_BS-2-THREE_NP108_NOT_PRESENT

2-Critical

DFC in slot [dec] does not have three NP108s!

DFC does not have three NP108s which is an illegal configuration

-

LOG_STD_ACTION

NP_BS-3-MEM_TEST_FAIL

3-Error

NextPort Module [dec]/[dec]/[dec] memory test failed

NextPort BootStrap and Crash Monitor detected a failed NextPort module memory test

-

LOG_STD_ACTION

NP_BS-3-NULL_FW_PTR

3-Error

NULL NextPort Firmware pointer for [dec]/[dec]/[dec]

NextPort BootStrap and Crash Monitor detected a NULL NextPort firmware pointer

-

LOG_STD_ACTION

NP_BS-3-INVALID_FW

3-Error

Invalid NextPort Firmware for [dec]/[dec]/[dec]

NextPort BootStrap and Crash Monitor detected an invalid NextPort firmware

-

LOG_STD_ACTION

NP_BS-3-CRC_FAIL

3-Error

NextPort Module [dec]/[dec]/[dec] failed firmware image validation

NextPort BootStrap and Crash Monitor detected an a failed NextPort firmware CRC validation

-

LOG_STD_ACTION

NP_BS-3-INVALID_IDT

3-Error

NextPort Module [dec]/[dec]/[dec] detected an invalid IDT

NextPort BootStrap and Crash Monitor detected an invalid IDT

-

LOG_STD_ACTION

NP_BS-3-INVALID_MC_POST

3-Error

NextPort Module [dec]/[dec]/[dec] detected a module POST failure 0x[hec]

NextPort BootStrap and Crash Monitor detected an a module POST failure

-

LOG_STD_ACTION

NP_BS-3-Q_FAILURE

3-Error

NextPort Module [dec]/[dec]/[dec] control queue creation failure

NextPort BootStrap and Crash Monitor detected an control queue creation failure

-

LOG_STD_ACTION

NP_BS-6-MODULE_STARTED

6-Information

NextPort module [dec]/[dec]/[dec] Started - [dec].[dec].[dec].[dec]

NextPort BootStrap and Crash Monitor successfully started module

-

LOG_STD_NO_ACTION

NP_BS-3-NO_SUCH_MODULE

3-Error

[chars] nonexisting NP module [dec]/[dec]/[dec]

NextPort BootStrap and Crash Monitor detected an internal database error

-

LOG_STD_NO_ACTION

NP_BS-3-NOMEM

3-Error

[chars]

NextPort BootStrap and Crash Monitor Could not allocate memory \n\ for internal module database

-

LOG_STD_NO_ACTION

NP_BS-6-MODULE_STOPPED

6-Information

NextPort module [dec]/[dec]/[dec] Stopped

NextPort BootStrap and Crash Monitor stopped module

-

LOG_STD_NO_ACTION

NP_BS-3-NO_KEEPALIVE

3-Error

NextPort module [dec]/[dec]/[dec] failed to respond to keepalive message

NextPort BootStrap and Crash Monitor detected a module failed to\n\ respond to keepalive message

-

LOG_STD_NO_ACTION

NP_BS-3-MODULE_ACCESS_ERR

3-Error

Failed to access NextPort module [dec]/[dec]/[dec] crash info

NextPort BootStrap and Crash Monitor failed to access\n\ crash information

-

LOG_STD_NO_ACTION

NP_SSM-3-RUNTIME_ERROR

3-Error

SSM[dec]/[dec]: Session Runtime Error Code = [dec] Recovery Action = [dec]

Session and Service Manager Received a Runtime Error for the slot\n\ and port

-

LOG_STD_NO_ACTION

NP_SSM-3-INVALID_MSG

3-Error

SSM: Invalid Session/Service Message ID = 0x[hec]

Session and Service Manager Received an invalid message from the\n\ NextPort Message Dispatcher

-

LOG_STD_NO_ACTION

NP_SSM-3-INVALID_HANDLE

3-Error

SSM[dec]/[dec]: Invalid Session/Service Instance Handle

Session and Service Manager Received failed to obtain its instance\n\ handle for the slot/port

-

LOG_STD_NO_ACTION

NP_SSM-0-NOMEMORY

0-Emergency

Cannot allocate [dec] bytes of memory for [chars]

The system failed to allocate an important data structure due\n\ to the lack of memory

as

"show mem"

NP_SIGLIB-3-CPTONE_FORMAT_FAIL

3-Error

Format of cp tone failed for tone-id [dec] port [dec]/[dec]

Formatting of the call processing tone message to the nextport module\n\ failed

-

LOG_STD_ACTION

NP_SPE_DS-3-SPE_DNLD_INIT_FAIL

3-Error

[chars]

SPE download code failed to initialise - SPE download will fail

-

LOG_STD_NO_ACTION

NP_SPE_DS-3-SPE_DNLD_FAIL

3-Error

SPE [dec]/[dec]/[dec]/[dec]: [chars]

SPE download code failed - download aborted

-

LOG_STD_NO_ACTION

NP_SPE_DS-3-NOMEMORY

3-Error

Cannot allocate [dec] bytes of memory for [chars]

The system failed to allocate an important data structure due\n\ to the lack of memory

-

"show mem"

NP_UCODE-3-INVALID_FILE

3-Error

NP microcode [chars] for device [chars] is invalid [chars]

The file containing the microcode for an NP is not specified\n\ or not accessible. This could be due to an invalid configuration\n\ or because the microcode is missing in this image.

vsp-mid

LOG_STD_SH_TECH_ACTION

IXP_MAP-3-EXMEM

3-Error

[chars] [chars] error detected - [chars] [dec]

Error detected managing the external memory of a Network Processor.

c7600-sip-400-clnt

"This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-LOCK_BLOCK

3-Error

[chars] error detected - 0x[hec] [dec] [dec] [dec]

Error detected processing ESF Network Processor lock bit\n\ allocations.

c7600-sip-400-clnt

"This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-LOCK_LIST

3-Error

[chars] error detected - 0x[hec] [dec] [dec] [dec]

Error detected processing ESF Network Processor lock bit list\n\ allocations.

c7600-sip-400-clnt

"This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-STATS_BLOCK

3-Error

[chars] error detected - 0x[hec] 0x[hec] [dec] [dec] [dec]

Error detected processing ESF Network Processor stats block\n\ allocations.

c7600-sip-400-clnt

"This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-DROP_BLOCK

3-Error

[chars] error detected - 0x[hec] 0x[hec] [dec] [dec]

Error detected processing ESF Network Processor drop block\n\ allocations.

c7600-sip-400-clnt

"This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-NOMEM

3-Error

Memory Allocation Failure - [chars] : [chars]0x[hec]

Memory required to service one or more Network Processors\n\ could not be allocated.

c7600-sip-400-clnt

"This error may indicate that more memory \n\ must be installed on the affected card \n\ or platform in order to service all the\n\ features and related entities enabled via \n\ the configuration.\n\ \n\ Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-MAXEXCEED

3-Error

ESF NP Mapper Max Services Exceeded - [chars]: [chars] [dec]

The maximum number ESF Network Processor Client Mapper services have\n\ been exceeded.

c7600-sip-400-clnt

"Change the configuration to reduce the number of services configured.\n\ \n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-NOTFOUND

3-Error

ESF NP Client Mapper - [chars]: [chars] 0x[hec]

The ESF Network Processor Client Mapper could not locate a required \n\ software element.

c7600-sip-400-clnt

"Try to reload the IOS image on the affected \n\ card or platform.\n\\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-4-STUCK

4-Warning

Client ID0x[hec] 0x%08X not ready on [chars]

During reset of the ESF Network Processor one or more Network\n\ Processor Clients had not completed stop processing.

c7600-sip-400-clnt

"The system should still operate normally however statistics\n\ or state collected before the ESF Network Processor was reset\n\ may have been lost.\n\\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-4-IPC_FAIL

4-Warning

ESF IPC Command failed - [chars] NP=[chars] cmd=[dec] me=[dec] rc=[dec]

An IPC command sent to the ESF Network Processor failed.

c7600-sip-400-clnt

"This error indicates a possible problem with the\n\ Network Processor hardware or microcode. Reload\n\ the affected HW to clear the condition.\n\ \n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-INITFAIL

3-Error

Initialization Failed - [chars]: [chars] [chars]

Memory needed to service one or more Network Processors\n\ could not be initialized.

c7600-sip-400-clnt

"Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-NOMEM_S

3-Error

Memory Allocation Failure - [chars]: [chars] [chars]

Memory required to service one or more Network Processors could not\n\ be allocated.

c7600-sip-400-clnt

"This error may indicate that more memory \n\ must be installed on the affected card \n\ or platform in order to service all the\n\ features and related entities enabled via \n\ the configuration.\n\ \n\ Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-NPUNKNOWN

3-Error

Unsupported NP - [chars]: [chars] [chars]

An unsupported Network Processor has been detected.

c7600-sip-400-clnt

"Verify that the correct IOS image is loaded on the affected \n\ card or platform for the configured features.\n\ If the error persists record the output\n\ from the following commands:\n\\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-NPMEM

3-Error

[chars] [chars] error detected

Error detected with external memory of a ESF Network Processor.

c7600-sip-400-clnt

"This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-INTF

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the Interface ESF Network Processor\n\ Client Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device. \n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-HQF

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the HQF ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device. \n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-WRED

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the WRED ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-QOS

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the QOS ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-QOS_CONFIG

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A configuration error for the QOS ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. Change the configuration to \n\ correct the QOS ACL configuration problem.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-4-QUEUE_LIMIT_EXCEED

4-Warning

Warning: Line card default queue-limit exceeds the maximum transmit packet buffers [dec]. To ensure high priority traffic is

An error for the HQF ESF Network Processor Client\n\ Mapper was detected. The total of the default queue-limits\n\ exceeds the maximum transmit packet buffers for this line card.\n\ Under high traffic conditions the line card may run out of \n\ packet buffers and drop high priority traffic.

c7600-sip-400-clnt

"This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. Apply the QOS policy\n\ configuration in the output direction of each interface.\n\ Adjust the queue-limit so that the total of the queue-limits\n\ on this line card is less than the maximum transmit packet buffers.\n\ \n\ <Bullet><par>policy-map qlimit\n\ <Bullet><par>class class-default\n\ <Bullet><par> queue-limit 100000\n\\n\ <Bullet><par>interface Gig1/0/0\n\ <Bullet><par> service-policy output qlimit\n\\n\ If the error persist record the output from the following commands:\n\\n\ <Bullet><par><Bold>show policy-map interface <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-L2TPV3

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the L2TPV3 ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-ATOM

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the ATOM ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-VPLS

3-Error

Error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the VPLS ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-FRR_VLAN

3-Error

Error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the FRR Vlan ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-MPLSOGRE

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the MPLSOGRE ESF Network Processor\n\ Client Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-MPLSOMGRE

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the MPLSOGRE ESF Network Processor\n\ Client Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-CEM

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the CEM ESF Network Processor\n\ Client Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-TCAM

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the NetLogic NSE TCAM was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-SACL

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the Security ACL ESF Network\n\ Processor Client Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-SACL_CONFIG

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A configuration error for the Security ACL ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. Change the configuration to \n\ correct the QOS ACL configuration problem.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-IPSESS

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A configuration error for the IP Sessions ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persist reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-PPPOESESS

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A configuration error for the PPPOE Sessions ESF Network Processor\n\ Client Mapper was detected.

c7600-sip-400-clnt

"This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-L2SRC

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A configuration error for the L2SRC ESF Network Processor\n\ Client Mapper was detected.

c7600-sip-400-clnt

"This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-4-CONNECTION_EXCEED

4-Warning

The number of connections has reached the capacity of the line card [dec].

-

-

-

IXP_MAP-3-ACR

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the ACR ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400-clnt

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

IXP_MAP-3-CEMOUDP

3-Error

[chars] error detected: [chars] [chars] 0x[hec] 0x[hec]

A software programming error for the CEMOUDP ESF Network Processor Client\n\ Mapper was detected.

c7600-sip-400

"This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

VPLS_NP_CLIENT-3-NOMEM

3-Error

[chars]

VPLS NP Client failed to initialize properly which will result in\n\ improper operation of Any Transport Over MPLS feature

c7600-sip-400-clnt

"This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

VPLS_NP_CLIENT-3-INFO

3-Error

[chars]

VPLS NP Client failed to initialize properly which will result in\n\ improper operation of Any Transport Over MPLS feature

c7600-sip-400-clnt

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

VPLS_NP_CLIENT-4-WARN

4-Warning

[chars] [dec] [chars]

Entry could not be added because:\n\ 1. Entry passed is invalid.

c7600-sip-400-clnt

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

ATOM_NP_CLIENT-3-NOMEM

3-Error

[chars]

ATOM NP Client failed to initialize properly which will result in\n\ improper operation of Any Transport Over MPLS feature

vsp-mid

"This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

ATOM_NP_CLIENT-3-INFO

3-Error

[chars]

ATOM NP Client failed to initialize properly which will result in\n\ improper operation of Any Transport Over MPLS feature

vsp-mid

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

ATOM_NP_CLIENT-4-WARN

4-Warning

[chars] [dec] [chars]

AToM Entry could not be added because:\n\ 1. Entry passed is invalid.

vsp-mid

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-METADATA

3-Error

[chars] failed: [chars] [[chars]] [chars]

Processing of the Metadata for the specified Network\n\ Processor failed. The specified Network Processor will \n\ fail to operate.

SIP2_CLIENT_DDTS_COMP

"Try to reload the Network Processor microcode.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-INITFAIL

3-Error

NP Client Initialization Failed - [chars]: [chars] [chars]

NP Client could not initialize memory\n\ needed to service one or more Network Processors.

SIP2_CLIENT_DDTS_COMP

"This error may indicate that an incompatibility exists\n\ between the NP firmware and the associate IOS image.\n\ \n\ Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-NOMEM

3-Error

Memory Allocation Failure - [chars]: [chars] [chars]

NP Client could not allocate required memory\n\ needed to service one or more Network Processors.

SIP2_CLIENT_DDTS_COMP

"This error may indicate that more memory \n\ must be installed on the affected card \n\ or platform in order to service all the\n\ features and related entities enabled via \n\ the configuration.\n\ \n\ Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-NOTSUP

3-Error

NP Client Feature Not Supported - [chars]: [chars] [chars]

The NP Client does not support the specified feature.

SIP2_CLIENT_DDTS_COMP

"Verify that the correct IOS image is loaded on the affected \n\ card or platform for the configured features.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-MAXEXCEED

3-Error

NP Client Max Services Exceeded - [chars]: [chars] [chars]

The maximum number NP Client services have been exceeded.

SIP2_CLIENT_DDTS_COMP

"Change the configuration to reduce the number of services configured.\n\ \n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-NOTFOUND

3-Error

NP Client Software Element Not Found - [chars]: [chars] [chars]

The NP Client could not locate a required software element.

SIP2_CLIENT_DDTS_COMP

"Try to reload the IOS image on the affected \n\ card or platform.\n\\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-ALLEXISTS

3-Error

NP Client Previously Defined Software Element - [chars]: [chars] [chars]

The NP Client has detected a previously defined software element.

SIP2_CLIENT_DDTS_COMP

"Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-NPUNKNOWN

3-Error

NP Client Unsupported NP - [chars]: [chars] [chars]

NP Client detected an unsupported NP.

SIP2_CLIENT_DDTS_COMP

"Verify that the correct IOS image is loaded on the affected \n\ card or platform for the configured features.\n\ If the error persists record the output\n\ from the following commands:\n\\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-2-FATAL

2-Critical

NP Client [chars] : [chars] [dec] [dec]

NP Client software detected a critical programming error.

SIP2_CLIENT_DDTS_COMP

"Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-INTF

3-Error

[chars] [chars] on [chars] - [chars] if_number=[dec]

Interface NP Client detected an error.

SIP2_CLIENT_DDTS_COMP

"Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

NP_CLIENT-3-UNEXPECTED

3-Error

NP Client Unexpected - [chars]: [chars] [chars] [dec] [dec]

NP Client unexpected error condition.

SIP2_CLIENT_DDTS_COMP

"Record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\\n\ <Body><par>Provide this information to your technical support\n\ representative."

CEMOUDP_NP_CLIENT-3-NOMEM

3-Error

[chars]

CEMOUDP NP Client failed to initialize properly which will result in\n\ improper operation of cemoudp feature

vsp-mid

"This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

CEMOUDP_NP_CLIENT-3-INFO

3-Error

[chars]

CEMOUDP NP Client failed to initialize properly which will result in\n\ improper operation of cemoudp feature

vsp-mid

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

CEMOUDP_NP_CLIENT-4-WARN

4-Warning

[chars] [dec] [chars]

CEMOUDP Entry could not be added because:\n\ 1. Entry passed is invalid.

vsp-mid

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

L2TPV3_NP_CLIENT-3-NOMEM

3-Error

[chars]

L2TPv3 NP Client failed to initialize properly which will result in\n\ improper operation of l2tpv3 feature

vsp-mid

"This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

L2TPV3_NP_CLIENT-3-INFO

3-Error

[chars]

L2TPv3 NP Client failed to initialize properly which will result in\n\ improper operation of l2tpv3 feature

vsp-mid

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

L2TPV3_NP_CLIENT-4-WARN

4-Warning

[chars] [dec] [chars]

L2TPv3 Entry could not be added because:\n\ 1. Entry passed is invalid.

vsp-mid

"Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ <Bullet><par><Bold>show tech <NoBold>\n\ <Bullet><par><Bold>show log <NoBold>\n\ <Body><par>Provide this information to your technical support\n\ representative."

OBFL_ERRMSG-5-FILECREATEFAIL

5-Notice

OBFL [chars] App failed to open/create file [chars] . Errno = [dec]

The file O_CREATE operation failed

obfl

LOG_STD_NO_ACTION

OBFL_ERRMSG-5-FILEFSTATFAIL

5-Notice

OBFL [chars] App failed to fstat file [chars] . Errno = [dec]

The file fstat operation failed

obfl

LOG_STD_NO_ACTION

OBFL_ERRMSG-5-FILELSEEKFAIL

5-Notice

OBFL [chars] App failed to Lseek file [chars] . Errno = [dec]

The file lseek operation failed

obfl

LOG_STD_NO_ACTION

OBFL_ERRMSG-5-FILEMINFREEFAIL

5-Notice

OBFL [chars] App failed to set coalesce min free

Failed to set coalese min free value

obfl

LOG_STD_NO_ACTION

OBFL_ERRMSG-5-FILEOPENFAIL

5-Notice

OBFL [chars] App failed to open file [chars] . Errno = [dec]

The file open operation failed

obfl

LOG_STD_NO_ACTION

OBFL_ERRMSG-5-FILEREADFAIL

5-Notice

OBFL [chars] App read failure on file [chars] . Errno = [dec]

The file read operation failed

obfl

LOG_STD_NO_ACTION

OBFL_ERRMSG-5-HISTFILESMALL

5-Notice

OBFL [chars] App: history file is exceedingly small

The history file for this app has been detected to be very small

obfl

LOG_STD_NO_ACTION

OBFL-5-DISABLED

5-Notice

Onboard Failure Logging disabled

Onboard Failure Logging has been disabled

obfl

LOG_STD_NO_ACTION

OUNIC-4-APIERR

4-Warning

[chars][chars]: [chars]

RSVP API routine return error

ocp

"Copy the error message exactly as it appears and " "report it to your technical support representative."

OUNIC-4-QERR

4-Warning

[chars]

IOS OS API routine return error

ocp

"Copy the error message exactly as it appears and " "report it to your technical support representative."

OUNIC-4-PORTERR

4-Warning

failed getting local_port_id for: neighor [inet] remote_port_id=[dec]

An LMP state machine has encountered an event that is not legal or allowed in the current state.

ocp

"Write down the state and the event and " "call your Cisco technical support representative for assistance "

OLM-5-LSUMBADTEL

5-Notice

Invalid TE Link ID [dec] in Link Summary message

This is generally caused by race conditions wherein an LMP message is received from a neighbor before the first control channel goes UP [locally]. This conditions usually happens when a node reboots.

ocp

"If the problem persists even after the node has " "completed initialization enter sho ip olm command to find the LMP " "configuration and use the debug ip lmp packets and debug ip lmp " "generic command to gather additional context type information and " "call Cisco technical assistance."

OLM-3-LMPNONBR

3-Error

Internal error: Couldn't find neighbor while [chars]

An LMP processing that requires to access information about the neighbor has found that no such neighbor exists. This could be due to internal error.

ocp

"Turn on generic and packet level debugging using " "the command debug ip lmp and gather LMP configuration using the " "command show ip olm and gather the displayed information and " "contact Cisco technical assistance."

OLM-5-LMPUNKSRC

5-Notice

LMP rcvd msg from unknown src ip 0x[inet] link %

An LMP message has been received with invalid TLV length. This suggests that we have a broken LMP implementation on the sending neighbor.

ocp

"Locate the sending neighbor and turn on packet " "level debugging using the debug ip lmp packets command. On seeing " "an ill-formed LMP packet gather displayed information and contact " "the Cisco technical assistance."

OLM-3-LMPSNDFAIL

3-Error

Failed to send LMP msg to [chars]

-

ocp

LOG_STD_ACTION

OLM-5-LSUMMISMATCH

5-Notice

Link Summary parameter[chars] mismatch

An LMP message has been received with invalid message type. This suggests that we have a broken LMP implementation on the sending neighbor

ocp

"Locate the sending neighbor and turn on packet " "level debugging using the debug ip lmp packets command. On seeing " "an ill-formed LMP packet gather displayed information and contact " "the Cisco technical assistance."

OLM-5-LMPNONBR1

5-Notice

No such neighbor to assign

An internal consistency error has been encountered during the said processing.

ocp

LOG_STD_ACTION

OLM-5-LMPMSGSEQ

5-Notice

LMP [chars] msg id [dec] not 1+[dec]

An LMP message has been received with message id that is not sequential within the Control channel or TE Link. This situation is not caused by the known cases that cause message id sequence to be broken including local node reboot neighbor node reboot and neighbor retransmission

ocp

"Enter the show ip olm stat command when this " "problem occurs and gather the information displayed and call the " "Cisco technical assistance."

OLM-3-LMPSDMISMATCH

3-Error

Service Discovery: Attribute [chars] incompatible with neighbor [chars]

Specified service attribute does not match with neighbor. The neighbor and/or the local node may not be properly configured.

ocp

""

OLM-3-LMPSDPORTFAILED

3-Error

Service Discovery: Attributes for port [chars] incompatible with nbr [chars]

Port-level service attribute does not match with those of the neighbor. The neighbor and/or the local node may not be properly configured.

ocp

""

OBJGROUP-3-QFAIL

3-Error

Failed to perform queue operation '[chars]'

Operation to perform processing on internal queue has failed.

asr1k-cts

LOG_STD_ACTION

OBJGROUP-3-CREATEFAIL

3-Error

Failed to create/initialize internal data structures

Operation to create/initialize internal data structures has failed.

asr1k-cts

LOG_STD_ACTION

OBJGROUP-3-CLASSMAP

3-Error

Failed to perform classmap filter [chars] operation

Operation to modify classmap filter has failed.

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-BADREFCNT

4-Warning

Bad reference counter classmap '[chars]' sgtid [dec] filter [dec]

Reference counter value indicates database inconsistency.

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-INVALIDFILTER

4-Warning

Invalid filter type [dec] for classmap '[chars]'

Filter type for match statement was unknown/invalid.

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-EINVAL

4-Warning

Unexpected input value

An unexpected input value to a function was incorrect

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-BADCHILD

4-Warning

Object-group '[chars]' has bad child '[chars]'

Object-group has reference to invalid child object-group

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-BADCLASSMAP

4-Warning

Internal match structure points to invalid class-map '[chars]'

Object-group has reference to invalid child object-group

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-BADMATCH

4-Warning

Invalid internal match structure in class-map '[chars]' type [dec]

Object-group has reference to invalid match

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-BADOG

4-Warning

Reference to non-existent object-group '[chars]'

Internal structure references non-existent object-group

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-INVALIDCMD

4-Warning

Invalid subcommand [dec]

Attempt to configure invalid subcommand

asr1k-cts

LOG_STD_ACTION

OBJGROUP-4-TOOMANYSGT

4-Warning

Exceeded maximum allowed SGT's [dec] in a class-map group-object

Local domain pattern length cannot exceed 100 for DSA.

xe-opendns-conn

"This message is for informational purposed only"

UMBRELLA-3-UMBRELLA_HA_INIT_FAILURE

3-Error

Failed to register with RF rc = [dec]

Organization does not exists

xe-opendns-conn

"Reactivtae Umbrella license"

EHSA-3-IPCERR

3-Error

[chars] [[chars]]

IPC failed for EHSA. EHSA messages cannot be transmitted .

-

"Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-3-KEEPTO

3-Error

No keepalive seen in [[dec]] secs: Failover [chars]

EHSA keepalive failure.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-3-STCHNG

3-Error

[chars] [[dec]]

EHSA State change detected

-

"Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-3-NOBUF

3-Error

[chars]

The IPC ran out of memory buffers.

-

"Reduce the number of applications currently running on the IPC. Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-3-EHSAINT

3-Error

'[chars]' at level [dec]

EHSA internal error.

Determine the component from the stack trace and process name displayed in the error message. Use Topic to search for a similar DDTS. If you find none write a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-2-EHSALOAD

2-Critical

[chars]

Netbooting was attempted on an EHSA Secondary

-

"Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-2-EHSASW

2-Critical

[chars]

Primary has crashed or is unresponsive. Secondary is taking over

-

"Copy the error message exactly as it appears and report it to your technical support representative."

EHSA-3-EHSABADST

3-Error

[chars] [[dec]] [[dec]]

EHSA internal error.

Determine the component from the stack trace and process name displayed in the error message. Use Topic to search for a similar DDTS. If you find none write a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your technical support representative."

CALLPROG-3-API_INIT

3-Error

api front init failed for [chars]

Failed to get free element from front end queue.

Call Progress Notification

"Platform requires additional free elements to properly function.\n\ Stop using Call Progress Notification applications.\n\ Call TAC to report the problem"

PRST_IFS-3-GENERAL

3-Error

persistent media IFS general error: [chars]

Persistent media module file system general error

-

LOG_STD_ACTION

PRST_IFS-3-FILE

3-Error

persistent media IFS file error: [chars]

Persistent media module file system file error

-

LOG_STD_ACTION

PRST_IFS-3-FILEMEM

3-Error

No memory to update [chars]. Please free some space

There is no filesystem memory for the system to write an updated version of the persistent variable file.

-

"Please free space on the filesystem shown in the error message" " as soon as possible. This will involve deleting existing files" " and/or squeezing the filesystem if the filesystem requires it" " bootflash for example may require it."

TRACEBACK_ERR_REC-7-MAX_UNIQUE_TRACEBACKS

7-Debug

The error: [dec] in function [chars] in the file [chars]:[dec] in process: [chars] was not recorded by the traceback error recording library under user: [chars].

The Library can only store so many error tracebacks and this number had been reached so all future attempts to store error tracebacks will print syslogs.

os

"Please clear the tracebacks for the user above. Is it " "recommended that the detailed show command is collected before " "clearing the data."

POLICY_MANAGER-2-INIT_FAILURE

2-Critical

Init failure: [chars]

A problem occurred in the Policy Manager during initialization

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-3-PRE_INIT_CALL

3-Error

Policy Manager routine called prior to initialization

The Policy Manager component was called prior to initialization. This could result in vital information being lost.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-2-NO_FREE_EVENT_BUFFERS

2-Critical

Event pool depleted: [chars]

The event pool has been depleted. There are no free buffers to process event

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-3-INVALID_SEVERITY

3-Error

Invalid event severity 0x[hec]

The event that was received by the Policy Manager contained an invalid severity and was therefore not processed.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-3-NULL_ACTION_ROUTINE

3-Error

NULL action routine invoked

The Policy Manager attempted to invoke an action which was NULL

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-3-INVALID_ACTION

3-Error

Invalid action

An invalid Policy Manager action was detected.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-3-INVALID_PARAMETERS

3-Error

A call to Policy Manager is made with invalid parameters

A call to Policy Manager was made with one or more invalid parameters

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

POLICY_MANAGER-3-NO_FREE_POLICY_IDS

3-Error

No more Policy IDs available

There are no more Policy IDs that can be allocated. The effect of this is that Policy Manager policies can no longer be created.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

LOGIN-3-TOOMANY_AUTHFAILS

3-Error

Too many Login Authentication failures have occurred in the last one minute on the line [dec].

A large number of authentication failures greater than the configured limit have occurred in the last one

security keyword:autosec

"Make sure it is not by any malicious attempt to gain" " access to the device"

AUDIT-3-NOPROC

3-Error

Cannot create Audit process.

Insufficient internal resource available to create process.

-

"Check available memory on router."

AUDIT-3-NOFILE

3-Error

Cannot create Audit file.

File system error while creating the audit file.

-

"Check DISK filesystems on the router."

AUDIT-3-FILE_RESIZE_ERR

3-Error

Cannot resize Audit file.

File system error while resizing the audit file.

-

"Check DISK filesystems on the router."

AUDIT-3-FILE_WRITE_ERR

3-Error

Cannot write to Audit file.

File system error while writing to the audit file.

-

"Check DISK filesystems on the router."

AUDIT-5-AUDIT_ENABLED

5-Notice

Auditing enabled

Audit was enabled on the router.

-

"Audit logs can be verified if changes are valid"

AUDIT-5-AUDIT_DISABLED

5-Notice

Auditing disabled

Audit was disabled on the router.

-

"Check if Audit was disabled by someone authorized to do so"

AUDIT-5-RUN_CONFIG

5-Notice

Running Configuration changed. Hash: [chars]

Running Config on the router changed.

-

"Check if it is a valid change in config."

AUDIT-5-RUN_VERSION

5-Notice

Running Version changed. Hash: [chars]

Running Version on the router changed.

-

"Check if it is a valid change."

AUDIT-5-STARTUP_CONFIG

5-Notice

Startup Configuration changed. Hash: [chars]

Startup config on the router changed.

-

"Check if it is a valid change."

AUDIT-5-FILESYSTEM

5-Notice

Filesystem changed. Hash: [chars]

FLASH/DISK Filesystems on the router changed.

-

"Check if it is a valid change."

AUDIT-5-HARDWARE_CONFIG

5-Notice

Hardware changed. Hash: [chars]

Hardware on the router changed.

-

"Check if it is a valid change."

AUDIT-1-FILE_ROLLOVER

1-Alert

Audit File Roll-over: [dec]

Audit Circular File Rolled Over.

-

"Increase Audit filesize."

GEN_DB-3-NULL_TREE_NODE

3-Error

Node is NULL [chars]

This message indicates that the tree node being examined is NULL

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-INVALID_RECORD_KEY

3-Error

[chars]: invalid record key *

This message indicates that the record key is invalid

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-NO_KEY_FUNC

3-Error

[chars]: [chars][chars]

This message indicates that key functions are missing from the database handle or key function is a NULL Pointer

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-KEY_FUNC_DOESNT_EXIST

3-Error

[chars]: Key function does not exist

This message indicates that key function being considered does not exist in the database definition

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-INVALID_CLIENT_TYPE

3-Error

[chars]: Invalid client type got [dec] must be between 0 and [dec]

This message indicates that client type is outside the expected range

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-NULL_DB_HNDL

3-Error

NULL Database Handle [chars]

This message indicates the database handle was NULL

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-NULL_DB_HNDL_ELEMENT

3-Error

[chars]: NULL Database Element [chars]

This message indicates the database handle element was NULL

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-LIST_FAIL

3-Error

[chars]:[chars]

This message indicates that a list operations such as enqueue dequeu failed

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-LIST_FAIL_FOR_RECORD

3-Error

[chars]:[dec]:[chars]

This message indicates that a list operations such as enqueue dequeu failed

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-WAVL_FAIL

3-Error

[chars]: [chars]

This message indicates that a wavl tree operation failed

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-RECORD_DELETE_FAIL

3-Error

[chars]:[chars]

This message indicates that a record could not be deleted

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-PARSER_INIT_FAIL

3-Error

[chars]:[dec]: Parser Could not be initialized

This message indicates that the IOS Parser command could not be initialized

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GEN_DB-3-UNKNOWN_PARSER_CMD

3-Error

[chars]:[dec]: Unknown Parser Command

This message indicates that the IOS Parser command was not recognized

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SCHED_TEST-6-ERRMSG

6-Information

This errmsg should print correctly.

-

-

-

SCHED_TEST-2-EXITHOOK

2-Critical

Exit routine invoked for process [chars].

-

-

-

SLOTDUMP-3-CORE_DUMP_ERROR

3-Error

Core dump error slot [dec]: [chars]

An error occured during a core dump of slot

-

"None."

TRANGE-2-NOMEMORY

2-Critical

Alloc fail for time-range config buffer. Disabling distributed mode on lc

Unable to malloc a buffer to send time-range configuration down to linecards.

-

"Enter a show chunks command and report the output along with this error message to your technical support representative."

TRANGE-2-WRONGREQUEST

2-Critical

Invalid request to allocate chunk of size [dec]

We only allow time-range chunks of max size TRANGE_LARGE_CHUNK_SZ

-

" "

TRANGE-2-WRONGSIZE

2-Critical

Incorrect length trange ipc xdr of len=[dec] received

The RP sent a time-range config message of the wrong size

-

"Report this error message to your tech support representative."

OTV_APP-3-INVALID_EVENT_THREAD

3-Error

An OTV Application routine was called by an invalid thread

This is an internal error triggered when an OTV Application routine is called incorrectly.

ios-otv-app

"This error message likely indicates an internal IOS " "software issue. As a result the internal state of " "the device may now be incorrect and a reboot of the " "device should be performed. Use the Cisco software " "defect search tool to determine if this issue has " "been fixed in a later software release. If no " "defect is found then please contact your Cisco " "technical support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

OTV_APP-3-INVALID_UPDATE_MAC_FLOOD

3-Error

otv mac flood [enet] was not added to the RIB the return code was [hec]

This is a RIB error whic was triggered when an OTV Application routine tried to add a route to the data base.

ios-otv-app

"This error message likely indicates an internal IOS " "software issue. As a result the internal state of " "the device may now be incorrect and one should " "reconfigure otv mac flood. If this error continues " "to occur use the Cisco software defect search " "tool to determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

OTV_APP-3-INVALID_DELETE_MAC_FLOOD

3-Error

otv mac flood [enet] was not deleted from the RIB the return code was [hec]

This is a RIB error which was triggered when an OTV Application routine tried to delete a route to the data base.

ios-otv-app

"This error message likely indicates an internal IOS " "software issue. As a result the internal state of " "the device may now be incorrect and one should " "reconfigure otv mac flood and try deleting it. If " "this error continues use the Cisco software defect " "search tool to determine if this issue has been " "fixed in a later software release. If no " "defect is found then please contact your " "Cisco technical support representative and " "provide the representative with the exact error " "message seen as well as the version of IOS being " "used."

OTV_APP-3-INVALID_ROUTE_REDIST_REG

3-Error

OTV was unable to register for route redistribution

This is a RIB error which was triggered when an OTV Application routine tried to send a redistribution request.

ios-otv-app

"This error message likely indicates an internal IOS " "software issue. As a result the internal state of " "the device may now be incorrect and one should " "reconfigure the overlay. If this continues " "use the Cisco software defect search tool " "to determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

OTV_APP-3-INVALID_CLIENT_REG

3-Error

OTV was unable to register with RIB

This is an RIB error triggered when an OTV Application routine tried to register as a client with MLRIB.

ios-otv-app

"This error message likely indicates an internal IOS " "software issue. As a result the internal state of " "the device may now be incorrect and one should " "reboot the device. If this continues use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

OTV_APP-3-INVALID_MCAST_MAPPING

3-Error

OTV was unable to process ISIS mapping received

This is an ISIS error triggered when an ISIS tries to send an invalid mapping to OTV.

ios-otv-app

"This error message likely indicates an internal IOS " "software issue. As a result the internal state of " "the device may now be incorrect and one should " "reboot the device. If this continues use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used."

PAGP_DUAL_ACTIVE-4-NO_CHNL_GROUP

4-Warning

Port [chars] channel group not present while [chars]

Extraction of the channel group from a link has failed but is expected to be present. This should not occur and may affect functionality depending on where it occurred.

cat6k-vs-infra

"This message should not be seen under normal operation. " "If it is appearing it is an indication of a software bug. " "Enter the commands:\n" "<CmdBold>show switch virtual dual-active summary<NoCmdBold>\n" "<CmdBold>show switch virtual dual-active pagp<NoCmdBold>\n" "Retrieve the PAgP packet contents by entering the commands:\n " "<CmdBold>debug condition interface <intfc><NoCmdBold>\n" "<CmdBold>debug pagp packet<NoCmdBold>\n" "and " LOG_STD_SH_TECH_ACTION

PAGP_DUAL_ACTIVE-3-ADD_TLV_FAIL

3-Error

Too few bytes for [chars] TLV in PAgP reqd. [dec] got [dec] on port [chars]

-

-

-

PAGP_DUAL_ACTIVE-3-REGISTRY_ADD_ERR

3-Error

Failure in adding to [chars] registry

Could not add a function to the registry

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-1-RECOVERY

1-Alert

PAgP running on [chars] triggered dual-active recovery: active id [enet] received expected [enet]

Pagp detected dual-active scenario on specified interface and caused switch to go into recovery mode.

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-3-RECOVERY_TRIGGER

3-Error

PAgP running on [chars] has detected a switchover or possible dual-active situation on the neighbor virtual switch. Informing virtual switches of active id change: new id [enet] old id [enet]

Pagp received new active id on specified interface indicating virtual switches are in a dual-active scenario. Interface is informing virtual switches of this which will cause one switch to go into recovery mode.

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-3-PROC_CREATE_FAILED

3-Error

Unable to create process \[chars]\

Unable to create the specified process

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-3-OBJECT_CREATE_FAILED

3-Error

Unable to create \[chars]\

Unable to create the specified managed object

cat6k-vs-infra

LOG_STD_NO_ACTION

AMDP2_FE-5-LOSTCARR

5-Notice

[chars] cable/transceiver problem?

The cable and/or transceiver is not connected.

pas-ethernet

"Connect the cable and/or transceiver."

AMDP2_FE-5-LATECOLL

5-Notice

[chars] transmit error

Late collisions occurred on the Ethernet/Fast Ethernet interface. When a collision occurs after the preamble has been transmitted then such a collision is called a LATE collision. The packet will be retransmitted but this condition could also indicate that another device is failing to detect when the network is in use.

pas-ethernet

"If the interface is Fast Ethernet verify that both " "peers are in the same duplex mode. For regular " "Ethernet the system should recover. No action is " "required."

AMDP2_FE-3-UNDERFLO

3-Error

[chars] transmit error

While transmitting a frame the controller chip's local buffer received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally such a problem is temporary depending on transient peak loads within the system.

pas-ethernet

"The system should recover. No action is required."

AMDP2_FE-4-BABBLE

4-Warning

[chars] transmit problem CSR0=[hex]

The transmitter has been on the channel longer than the time taken to transmit the largest frame

pas-ethernet

"The system should recover. No action is required."

AMDP2_FE-3-SPURIDON

3-Error

[chars] spurious chip init CSR[dec]=0x%04x

An illegal condition indicating initialization done has occurred.

pas-ethernet

"Clear the interface. " "If this message recurs call your technical support " "representative for assistance."

AMDP2_FE-1-MEMERR

1-Alert

[chars] CSR[dec]=0x%04x

The interface could not access system resources for a long time. This problem may occur under very heavy loads.

pas-ethernet

"The system should recover. No action is required. If the message " "recurs call your technical support representative for assistance."

AMDP2_FE-1-INITFAIL

1-Alert

[chars] CSR[dec]=0x%04x

The software failed to initialize/restart an Ethernet/Fast Ethernet interface.

pas-ethernet

"Try resetting the interface by doing a <CmdBold>shutdown <NoCmdBold> followed by " "a <CmdBold>no shutdown<NoCmdBold>. If the message recurs try reseating the Port " "Adaptor. If reseating also does not work call your technical " "support representative for assistance."

AMDP2_FE-1-DISCOVER

1-Alert

Only found [dec] interfaces on bay [dec] shutting down bay

The software could not identify the interface card.

pas-ethernet

"Power down reseat the interface card " "and reboot. If the message recurs call your " "technical support representative for assistance."

AMDP2_FE-1-NOTSUPPORTED

1-Alert

2FE PA not supported on NPE100 shutting down bay

2FE PA is not supported on a 7200 with NPE100.

pas-ethernet

"NPE150 or better is needed for 2FE PA."

AMDP2_FE-3-OWNERR

3-Error

[chars] packet buffer pak=0x[hec]

The software detected an error in descriptor ownership.

pas-ethernet

"Try a later version of the software. If the message " "recurs call your technical support representative " "for assistance."

AMDP2_FE-3-NOTAMDP2

3-Error

Slot [dec] device ID seen as [hex] expected [hex]

The software could not recognize the interface chips.

pas-ethernet

"Power down reseat the interface card and " "reboot. If the message recurs call your " "technical support representative for assistance."

AMDP2_FE-6-EXCESSCOLL

6-Information

[chars] TDR=[dec] TRC=[dec]

Ethernet/Fast Ethernet is seeing multiple collisions. This may occur under heavy loads.

pas-ethernet

"The system should recover. No action is " "required."

AMDP2_FE-2-NOISL

2-Critical

[chars] hardware does not support ISL

The interface cannot be configured as an ISL trunk.

pas-ethernet

"Check the configuration."

AMDP2_FE-1-NOMII

1-Alert

[chars] MII transceiver not connected

The MII transceiver was disconnected while the MII port was selected.

pas-ethernet

"Connect the transceiver and enter the <bold> " "shut <nobold> and <bold> no shut <nobold> commands for the " "interface in the configuration menu."

AMDP2_FE-3-TOOMANYPART

3-Error

Bad packet with [dec] particles pak=0x[hec]

The software detected an invalid packet.

pas-ethernet

"Try a later version of the software. If the message " "recurs call your technical support representative " "for assistance."

VPA-3-INITFAIL

3-Error

VPA bay [dec] Init Failed at [chars] - line [dec] arg [hec]

The port adaptor failed to complete hardware initialization.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-3-UNEXPEVENT

3-Error

VPA bay [dec] received an unexpected event=[hec]

The port adaptor received an unexpected event from firmware.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-3-TSBUSY

3-Error

VPA bay [dec] TDM timeslot is busy: ST=[dec]/TS=[dec]

The port adaptor failed to grand a cross connect setup request.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-3-TSNONBUSY

3-Error

VPA bay [dec] TDM timeslot is non busy: ST=[dec]/TS=[dec]

The port adaptor failed to grand a cross connect teardown request.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-5-TXVFULL

5-Notice

VPA bay [dec] Voice tx ring is full: dma_done=[dec] last_dma_done=[dec]

-

-

-

VPA-6-RXVFILLFAIL

6-Information

VPA bay [dec] Voice rx ring refill failed: rxv_fill_fail=[dec]

-

-

-

VPA-6-RXDFILLFAIL

6-Information

VPA bay [dec] Data rx ring refill failed: rxd_fill_fail=[dec]

-

-

-

VPA-3-TDMFAIL

3-Error

VPA-TDM access failed at [chars] - line [dec] arg1=0x%08xarg2=0x%08x

The port adaptor failed to access TDM switch.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-1-RPTFAIL

1-Alert

[chars] failed to send report [dec] at [chars] - line [dec]

The port adaptor failed to send a report from vip.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-3-CMDFAIL

3-Error

[chars] Command Failed at [chars] - line [dec] arg [dec]

The port adaptor failed to process a command.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-6-NOTSUPPORT

6-Information

Voice PA is not supported in this platform.

The port adaptor is not supported in this platform.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-3-FWCRASH

3-Error

Firmware for VPA in bay [dec] crashed with exception [hex]\n

The port adaptor firmware has crashed.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-6-NOTDMBP

6-Information

No TDM backplane is supported on slot [dec].

Cannot cross connect ds0 inter slot without the TDM backplane.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

VPA-3-BADVC

3-Error

[chars] [dec]/[dec] got bad VC packet \n%08x %08x %08x %08x %08x %08x %08x %08x

An interface received a packet with bad VC encapsulation. \n\ This indicates either a software or hardware problem.

-

LOG_STD_SH_TECH_ACTION

VPA-6-NODATA

6-Information

Data call is not supported on [chars].

Data call is not supported in this version of IOS.

-

"Remove data call configuration/setup."

PA-2-BADPABAY

2-Critical

Out of range PCI Port Adaptor bay [dec]

The software specified an out-of-range port adapter bay.

-

LOG_STD_ACTION

PA-2-BADINTERFACE

2-Critical

Out of range PCI Port Adaptor interface [dec] on bay [dec]

The software specified an out-of-range port adapter interface.

-

LOG_STD_ACTION

PA-3-PACREATE

3-Error

Unable to create driver for Port Adaptor type [dec] in bay [dec]

Possible memory shortage or adaptor hardware error

-

LOG_STD_ACTION

PA-2-UNDEFPA

2-Critical

Undefined Port Adaptor type [dec] in bay [dec]

The software does not have a driver for the port adapter type in the specified bay.

-

"Make sure the image you are running is supposed to support this card. " "Check that the card is properly seated. " LOG_STD_RECUR_ACTION

PA-2-UNDEFIO

2-Critical

Unsupported I/O Controller type [dec] in I/O Bay.

The software does not have a driver for the port adapter type in the specified bay.

-

"Make sure the image you are running is supposed to support this card. " "Newer I/O Controllers will only work with the -kboot- image. " LOG_STD_RECUR_ACTION

PA-3-REVNOTSUPPORTED

3-Error

PA in slot[dec] [chars] requires base h/w revision of [dec].[dec]

A newer hardware revision of the port adaptor is required for\n\ functional operation on this chassis.

-

LOG_STD_ACTION

PA-3-NOTSUPPORTED

3-Error

PA in slot[dec] [chars] is not supported on this [chars]

This port adaptor is not supported on this chassis/cpucard.

-

LOG_STD_ACTION

PA-3-SLOTNOTSUPPORTED

3-Error

This PA type [chars] is not supported in slot[dec] of this [chars]

This port adaptor is not supported on this slot of this chassis/cpucard.

-

LOG_STD_ACTION

PA-2-BADIDB

2-Critical

PA interface idb incorrect [hex]

The port adapter system control block PASCB data structure

-

LOG_STD_ACTION

PA-2-BADPASCB

2-Critical

PA interface pascb incorrect [hex]

The port adapter system control block PASCB data structure was

-

LOG_STD_ACTION

PA-0-RUPTCONFLICT

0-Emergency

Conflict detected when trying to install [chars] interrupt handler bay [dec].

An attempt was made to register an interrupt handler for\n\ either a non existent port adaptor or the wrong interrupt\n\ prority level.

-

LOG_STD_ACTION

PA-3-DEACTIVATED

3-Error

port adapter in bay [[dec]] powered off.

The port adapter is being powered off.

-

LOG_STD_SH_TECH_ACTION

PA-3-BRINGUPFAIL

3-Error

port adapter in bay [[dec]] failed to reset.

An attempt to reset and initialize the port adapter timed out.

-

LOG_STD_SH_TECH_ACTION

PA-2-PARECUR

2-Critical

Recursive loop while getting the daughtercard info for PA type [dec]

While getting the daughter card info for the chassismib the platform snmp code goes into an infinite loop.

-

LOG_STD_ACTION

PA-2-BADPINST

2-Critical

PA interface port_inst incorrect [hex]

Failure to access port instance internal data

-

LOG_STD_ACTION

PA-2-BADPA

2-Critical

PA interface pa incorrect [hex]

Incorrect PA interface specified

-

LOG_STD_ACTION

PA-2-BADPA2

2-Critical

PA null adapter [hex]

Null PA interface specified

-

LOG_STD_ACTION

PA-2-BADVCONT

2-Critical

PA interface vcont incorrect [hex]

Incorrect VC interface specified

-

LOG_STD_ACTION

PA-2-BADDAT

2-Critical

PA interface data incorrect [hex]

Incorrect PA interface data found

-

LOG_STD_ACTION

PA-2-QOVERFLOW

2-Critical

PA queue overflow cmd [hex]

-

-

LOG_STD_ACTION

PA-2-ILLEGALPA

2-Critical

Illegal Port Adaptor type [dec] in bay [dec] of [chars].

The port adapter is not supported by the controller to which it is plugged into.

-

"Remove the port adapter and return the controller to its original " "configuration."

PA-3-CONFIG

3-Error

Recommended port adapter configuration exceeded

The total bandwidth of fast and medium bandwidth port adapters\n\ exceed the rated capacity of this system.

-

"Refer to the configuration guidelines for the maximum allowed\n\ high and medium bandwidth port adapters for the system."

PA-4-PCIVALID

4-Warning

PCI activation failed bay [dec] 0x[hec]

The system received an invalid PCI signal from the port adapter.\n\ This is probably due to a hardware failure.

-

LOG_STD_ACTION

PA-3-IMPROPER_INSERT

3-Error

Improper insertion for slot [dec]. Remove and then re-insert the PA

PCI Activation of PA has failed thus the PA is deactivated\n\ and must be removed and then re-inserted.

-

"Remove and then re-insert the PA firmly into the slot."

PA-4-IMPROPER_REMOVAL

4-Warning

Improper removal for slot [dec].

PA was inserted and then removed while being initialised.

-

"After an insertion the PA should be pulled out only after the\n\ initialisation is complete. If there is any traffic running\n\ through the router the initialisation can take up to 30 seconds"

PA-2-UNDEFPABRIDGE

2-Critical

Unsupported Port Adaptor Bridge [hex] in bay [dec]

The software does not have a driver for that port adapter protocol control information bridge in the specified bay.

-

LOG_STD_ACTION

PA-2-PABRIDGE

2-Critical

Failed to config bridge for PA [dec]

The system side PCI bridge for this PA failed initialization.\n\ The PA will not be operational because of this.

-

LOG_STD_ACTION

PA-2-INCORRECTBRIDGEREG

2-Critical

Bad default register[hec] setting[hec] in PA bridge

The software is unable to configure certain settings for the port adapter protocol control information bridge in the specified bay.

-

LOG_STD_ACTION

ENTITY_ALARM-6-INFO

6-Information

[chars] [chars] [chars] [chars] [chars]

Alarm assertion or deassertion information.

-

LOG_STD_NO_ACTION

MUESLIX-3-OWNERR

3-Error

[dec] packet buffer pak=0x[hec]

A software or hardware error occurred. The Mx serial driver detected\n\ that the transmit ring is in an inconsistent and unrecoverable state.

pas-serial

"Enable 'debug serial mueslix' debug command. Then collect the \n\ 'show tech' and 'show log' information and send them \n\ to the DE team or CSE team. After that you can disable the \n\ 'debug serial mueslix' command."

MUESLIX-1-INITFAIL

1-Alert

Mx serial bay [dec] Init Failed at [chars]

The Mx serial port adaptor failed to complete hardware \n\ initialization.

pas-serial

"Try to reseat the PA properly in the system slots. If the error\n\ still happens then verify for the hardware failure including \n\ the 7200 chasis in case of 7200 or vip in case of 7500 and the PA \n\ as this error will come only if there is a failure in hardware."

MUESLIX-1-STARTFAIL

1-Alert

Mx serial [chars] Start Failed at [chars]

A software or hardware error occurred. The Mx microcode is not\n\ responding to the enable command used to restart the serial interface

pas-serial

"Enable 'debug serial mueslix' debug command. Then collect the \n\ 'show tech' and 'show log' information and send them \n\ to the DE team or CSE team. After that you can disable the \n\ 'debug serial mueslix' command."

MUESLIX-1-STOPFAIL

1-Alert

Mx serial [chars] Stop Failed at [chars]

A software or hardware error occurred. The Mx microcode is not\n\ responding to the disable command used to stop the serial port.

pas-serial

"Enable 'debug serial mueslix' debug command. Then collect the \n\ 'show tech' and 'show log' information and send them \n\ to the technical support representative. After that you can \n\ disable the 'debug serial mueslix' command."

MUESLIX-1-FAILURE_CAUSE

1-Alert

[chars]: [chars][chars]: 0x%08x 0x%08x

Pull the info from the port adaptor to show what error caused\n\ the STOPFAIL/STARTFAIL problem.

pas-serial

"Enable 'debug serial mueslix' debug command. Then collect the \n\ 'show tech' and 'show log' information and send them \n\ to the technical support representative. After that you can \n\ disable the 'debug serial mueslix' command."

MUESLIX-1-DWNLDFL

1-Alert

Mx serial bay [dec]: PA down load failed

The Mx serial hardware failed. It could not download its \n\ operational microcode.

pas-serial

"Try to reseat the PA properly in the system slots. If the error\n\ still happens then verify for the hardware failure including \n\ the 7200 chasis in case of 7200 or vip in case of RSP and the PA \n\ as this error will come only if there is a failure in hardware."

MUESLIX-3-DISCOVER

3-Error

Mx serial bay [dec]: Interface found: [dec]

The system couldn't able to recognize all the Mueslix devices\n\ that are there on the system

pas-serial

"Try to reseat the PA properly in the system slots. If the error\n\ is still happening then verify for the hardware failure including \n\ the 7200 chasis in case of 7200 or vip in case of RSP and the PA \n\ as this error will come only if there is a failure in hardware."

MUESLIX-3-NOTMUESLIX

3-Error

Mx serial bay [dec]: Device reported [hex]

The system hardware failed. A non-Mx serial device pointed at the\n\ Mx serial software.

pas-serial

"Check the system configuration for the failure in the bay number \n\ that is reported in the error message. If it is not a mueslix \n\ based PA then contact the appropriate component to which that PA \n\ belongs. If it is a mueslix based PA then try to reseat the PA \n\ once agian and if the error still comes then collect the 'show tech' \n\ and 'show log' information at the time of this problem and send it\n\ to the technical support representative"

MUESLIX-1-HALT

1-Alert

Mx serial: [chars] TPU halted: cause 0x%2x status 0x%08x shadow 0x%08x

The Mx serial firmware is not in sync with the driver.

pas-serial

"This conditions will clear by itself. Enable 'debug serial mueslix' \n\ debug command. Then collect the 'show tech' and 'show log' \n\ information and send them to the DE team or CSE team. After \n\ that you can disable the 'debug serial mueslix' command."

MUESLIX-4-DEF_SUBRATE

4-Warning

[chars] [chars]

User has changed the dsu bandwidth using DS3 remote\n\ management commands. This won't change the user configured dsu bandwidth

pas-serial

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

MUESLIX-1-CLOCKRATE

1-Alert

[chars]:Link is brought [chars] due to clock rate change threshold configured = [dec] received clock rate = [dec]

The received clock rate is changed from below the threshold\n\ configured to above or vice versa..

pas-serial

"Check the received clock rate from the provider end if the clock rate falls below the threshold configured"

MUESLIX-3-ERROR

3-Error

[chars]

General error information.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

_NEW_APP_NAME_-6-MSG_INF

6-Information

[chars]

Program information

-

-

_NEW_APP_NAME_-7-MSG_DBG

7-Debug

[chars]

Debug Messages

-

-

_NEW_APP_NAME_-3-MSG_ERR

3-Error

[chars]

Error Messages

pagent

"try debug command"

PMOD-6-MSG_INF

6-Information

[chars]

Program information

-

-

PMOD-7-MSG_DBG

7-Debug

[chars]

Debug Messages

-

-

PMOD-3-MSG_ERR

3-Error

[chars]

Error Messages

pagent

"try debug command"

PGTT_IPC_MSG-2-ALLOC_ERR

2-Critical

Unable to allocate message packet to SECONDARY [dec].

-

-

-

PGTT_IPC_MSG-2-RVT_PRIMARY_CREATE_ERR

2-Critical

Unable to create RVT-PRIMARY port.

-

-

-

PGTT_IPC_MSG-2-IPC_MSG_HANDLER_ERR

2-Critical

Error handling IPC message from SECONDARY processor.

-

-

-

PGTT_IPC_MSG-2-IPC_PORT_TO_SECONDARY_ERR

2-Critical

Unable to open IPC port to SECONDARY slot %ld: [chars].

-

-

-

PGTT_IPC_MSG-2-PGTT_MSG_DEBUG

2-Critical

[chars]

-

-

-

PGTT_IPC_MSG-2-PKTS_ALLOC_ERR

2-Critical

PKTS could not allocate message packet to SECONDARY [dec].

-

-

-

PGTT_IPC_MSG-2-PKTS_COUNT_REPLY_ALLOC_ERR

2-Critical

PKTS could not allocate count reply message.

-

-

-

PGEN_IPC_MSG-2-PORT_CREATE_ERR

2-Critical

Unable to create Pagent IPC port

-

-

-

PGEN_IPC_MSG-2-ALLOC_ERR

2-Critical

Unable to allocate IPC message

-

-

-

PGEN_IPC_MSG-2-PORT_LOCATE_ERR

2-Critical

Unable to locate [chars] port during registration

-

-

-

PGEN_IPC_MSG-2-PORT_SEND_ERR

2-Critical

Unable to send message

-

-

-

PGEN_IPC_MSG-2-PORT_OPEN_ERR

2-Critical

Unable to open port: [chars]

-

-

-

PGEN_IPC_MSG-2-CREATE_REG_ERR

2-Critical

Unable to create Pagent IPC Registry

-

-

-

PGEN_IPC_MSG-2-NO_HANDLER_ERR

2-Critical

No handler found for IPC code %ld

-

-

-

PGEN_IPC_MSG-2-IDBLIST_CREATE_ERR

2-Critical

Unable to create SVIP IDB list

-

-

-

PGEN_IPC_MSG-2-PAK_ALLOC_ERR

2-Critical

Unable to allocate download packet structure

-

-

-

PGEN_IPC_MSG-2-PAK_DATA_ALLOC_ERR

2-Critical

Unable to allocate download packet data

-

-

-

PGEN_IPC_MSG-2-HWIDB_PG_ALLOC_ERR

2-Critical

Unable to allocate hwidb_pg structure

-

-

-

PGEN_IPC_MSG-2-PG_FILTER_LIST_ALLOC_ERR

2-Critical

Unable to allocate pg_filter_list structure

-

-

-

PGEN_IPC_MSG-2-PG_FASTCOUNT_ERR

2-Critical

Unable to stop/start Pagent fastcount

-

-

-

PGEN_IPC_MSG-2-SELECT_PAK_ALLOC_ERR

2-Critical

Unable to allocate download selection packet structure

-

-

-

PGEN_IPC_MSG-2-SELECT_DATA_ALLOC_ERR

2-Critical

Unable to allocate download selection data

-

-

-

PGEN_IPC_MSG-2-SELECT_ALLOC

2-Critical

Allocate download selection %ld

-

-

-

PGEN_IPC_MSG-2-SELECT_ALLOC_ERR

2-Critical

Unable to allocate select context structure

-

-

-

PGEN_IPC_MSG-2-SELECT_RECV_ERR

2-Critical

Received unexpected selection packet

-

-

-

PGEN_IPC_MSG-2-SEQ_LOCATE_ERR

2-Critical

Unable to allocate sequence storage

-

-

-

PGEN_IPC_MSG-2-PGEN_IPC_REPLY_ALLOC_ERR

2-Critical

Unable to allocate IPC message for reply

-

-

-

PGEN_IPC_MSG-2-PGEN_IPC_REPLAY_END_ALLOC_ERR

2-Critical

Unable to allocate IPC message for end of replay

-

-

-

PGEN_VIP_MSG-2-PGEN_VIP_MSG_TRANSMIT_PAK

2-Critical

Unable to allocate VIP transmit pak

-

-

-

PGEN_VIP_MSG-2-PGEN_VIP_MSG_TEST

2-Critical

[chars]

-

-

-

FTPSE-6-MSG_INF

6-Information

[chars]

Program information

-

-

FTPSE-7-MSG_DBG

7-Debug

[chars]

Debug Messages

-

-

FTPSE-3-MSG_ERR

3-Error

[chars]

Error Messages

pagent

"try debug command"

FTPSE-6-NETWRTFAILED

6-Information

FTPSE Server:connection / tcp_write failed.

A TCP write failed while sending an FTP command reply to the client.

-

"Verify network connection from client to server and verify ftp client operation."

PG_TCP-6-MSG_INF

6-Information

[chars]

Program information

-

-

PG_TCP-7-MSG_DBG

7-Debug

[chars]

Debug Messages

-

-

PG_TCP-3-MSG_ERR

3-Error

[chars]

Error Messages

pagent

"try debug command"

PNNI-4-BADPACKET

4-Warning

Invalid [chars] pkt: [chars] [dec] [dec]

An invalid packet was received from a network peer.

-

"Check the originating device for a cause of the corrupted packets."

PNNI-3-INTERNAL_ERROR

3-Error

[chars][chars] [hec]

An internal software error occurred. The message contains more information that can be used to identify the problem.

-

LOG_STD_ACTION

PNNI-4-CONFIG_ERROR

4-Warning

Configuration Error: [chars]

This message indicates a configuration error in the PNNI subsystem. The message will display more specific information about the cause of problem.

-

"Change the confguration to correct the error."

PNNI-2-SPF_ERROR

2-Critical

Tent List Overflow in [chars]

An internal software error occurred.

-

LOG_STD_ACTION

PNNI-4-ADDRESS_EXIST

4-Warning

Address derived from the switch's prefix by soft PVC manager [chars] clashes with existing address in prefix table

An PVC port address assignment has collided with an existing address. An address that would have been assigned by this switch has already been assigned by another.

-

"If possible assign a new MAC address to the peer system that caused the assignment collision."

PNNI-4-BADROUTEREQ

4-Warning

Bad Request from Signaling [hec]

A source routing request by another network host was corrupted.

-

"Check the originating system for a cause of the problem."

PNNI-3-INVALID_MEM

3-Error

Bad address of [chars] [hex] please collect \show atm pnni trace error\

An internal software error occurred.

-

"Use \"show atm pnni trace error\" to collect more information. " LOG_STD_RECUR_ACTION

PNNI-2-NO_INTERNAL_NUMBER

2-Critical

Empty Internal Number Stack: [chars]

An internal software error has occurred.

-

LOG_STD_SH_TECH_ACTION

PNNI-2-FLOOD_ERROR

2-Critical

[chars]

-

-

-

PNNI-7-DEBUG

7-Debug

[chars]

This is an informational message only. It is used by Cisco for testing.

-

"Informational messages can be disabled by changing logging level."

PNNI-6-INFO

6-Information

[chars]

This is an informational message only.

-

"Informational messages can be disabled by changing logging level."

PNNI-4-DUPLICATE_NODE_ID

4-Warning

[chars] [chars] for node [dec] [chars]

An internal software error occurred.

-

LOG_STD_ACTION

PNNI-4-ATM_SYS_ERROR

4-Warning

Error: [chars]

An internal software error occurred.

-

"LOG_STD_ACTION"

PM_MODEM_HIST-7-TRACE_HDR

7-Debug

\n\nModem [chars] Events Log:

This is the initial message for the trace of the specified modem.\n\ The modem's stored trace messages will follow.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-MODEM_STATIC_EVT

7-Debug

\n[chars]: [chars] \n[chars]

This is a tracing message indicating a static event reported by\n\ the specified modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-MODEM_DYNAMIC_EVT

7-Debug

\n[chars]: [chars] \n[chars]

This is a tracing message indicating a dynamic event reported by\n\ the specified modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-MODEM_ROS_EVT

7-Debug

\n[chars]: [chars] \n[chars]

This is a tracing message indicating a link rate event reported by\n\ the specified modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-MODEM_END_CONN_EVT

7-Debug

\n[chars]: [chars] \n[chars]

This is a tracing message indicating an end-connection event\n\ from the specified modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-MODEM_STATE_EVT

7-Debug

\n[chars]: [chars] \n%*s State: [chars]

This is a tracing message indicating a state event reported by\n\ the specified modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-PORT_STATE_REACHED_NTF_EVT

7-Debug

\n[chars]: [chars] [chars]

This is a tracing message indicating a link rate event reported by\n\ the specified modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-CSM_OC_CALLED_NUM

7-Debug

\n[chars]: ISDN outgoing called number: [chars]

This is a tracing message indicating a dialed ISDN number.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-CSM_IC_CALLING_NUM

7-Debug

\n[chars]: ISDN incoming caller number: [chars]

This is a tracing message indicating the number of an incoming\n\ ISDN caller.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-CSM_IC_CALLED_NUM

7-Debug

\n[chars]: ISDN incoming called number: [chars]

This is a tracing message indicating the number of the ISDN\n\ line recieving a call.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-UNKNOWN_FRAME

7-Debug

\n[chars]: Error in events log

This is a tracing message indicating a formatting error in the\n\ modem event history. One or more events may be missing from\n\ the trace.

-

LOG_STD_DBG_ACTION

PM_MODEM_HIST-7-UNKNOWN_EVENT

7-Debug

\n[chars]: Error in events log

This is a tracing message indicating a formatting error in the\n\ modem event history. One or more events may be missing from\n\ the trace.

-

LOG_STD_DBG_ACTION

PM_MODEM_MAINT-1-INITFAIL

1-Alert

Initialization failed.

Modem maintenance facility initialization failed.

-

"Disable Autotest Poweron test and avoid manual back-2-back test." LOG_STD_ACTION

PM_MODEM_MAINT-1-BADEVENT

1-Alert

Invalid modem management [chars] event 0x%02x for modem[chars]

The modem management facility received an unrecognize event.

-

LOG_STD_ACTION

PM_MODEM_MAINT-4-BADMODEMS

4-Warning

Modems [chars] and [chars] failed back-to-back test: [chars]

The two modems reported in the message failed a back-to-back test.\n\ At least one of them has failed.

-

"Perform more back to back tests by pairing the failed modems with\n\ other modems to determine which modem is bad. Check the failed\n\ modems again after performing a power cycle. " LOG_STD_RECUR_ACTION

PM_MODEM_MAINT-5-B2BMODEMS

5-Notice

Modems [chars] and [chars] completed back-to-back test:

The reported modems have passed the back to back test without any\n\ errors.

-

LOG_STD_NO_ACTION

PM_MODEM_MAINT-1-BADMODEM

1-Alert

Modem [chars] failed [chars]

A software or hardware problem has been detected on a modem.\n\ The specific modem and reason are listed in the message.

-

LOG_STD_ACTION

PM_MODEM_MAINT-5-MODEM_OK

5-Notice

Modem [chars] passed the test

Tests on the specified modem were successful.

-

LOG_STD_NO_ACTION

PM_MODEM_MAINT-5-B2BCONNECT

5-Notice

Modems [chars] and [chars] connected in back-to-back test: [chars]

A back to back test connection has been made between the selected\n\ modems. The test is still in progress.

-

LOG_STD_NO_ACTION

PM_MODEM_MAINT-5-B2BINIT

5-Notice

Auto Back-to-Back test initiated by [chars]

This is a tracing message indicating an automatic back-to-back\n\ test was initiated by the specified MICA modem.

-

LOG_STD_DBG_ACTION

PM_MODEM_MAINT-4-B2BABORT

4-Warning

Modems [chars] and [chars] back-to-back test: aborted

The PM SPE State Machine has run out of event memory.

port-mgmt

LOG_STD_ACTION

SPE-3-SM_RESPONSE_NO_MEM

3-Error

SPE SM out of response buffers

The PM SPE State Machine has run out of response event memroy.

port-mgmt

LOG_STD_ACTION

SPE-6-NULL_OBJ

6-Information

SPE object [chars] is unavailable.

Information about this SPE could not be retrieved. The SPE may not exist.

-

LOG_STD_NO_ACTION

SPE-3-SM_POST_FAILED

3-Error

SPE [chars] is BAD.

The SPE failed the POST and it will be marked BAD.

-

LOG_STD_NO_ACTION

SPE-3-SM_DOWNLOAD_FAILED

3-Error

SPE [chars] is BAD - [chars].

The SPE failed to download and it will be marked BAD.

-

LOG_STD_NO_ACTION

SPE-3-SM_CRASHED

3-Error

SPE [chars] crashed

The firmware running on the SPE aborted.

-

LOG_STD_NO_ACTION

SPE-6-SM_SHUTDOWN

6-Information

SPE [chars] shutdown

The SPE is taken out of service. Maintenance activities cannot be performed.

-

LOG_STD_NO_ACTION

SPE-6-SM_BUSIEDOUT

6-Information

SPE [chars] busiedoutmaintenance will be allowed

The SPE is taken out of service temporarily. Maintanence activities can still be performed.

-

LOG_STD_NO_ACTION

SPE-6-SM_CLEARED

6-Information

SPE [chars] Cleared

The SPE will be re-downloaded with the configured firmware.

-

LOG_STD_NO_ACTION

SPE-6-SM_START_DOWNLOAD

6-Information

SPE [chars] : Firmware download initiated

Firmware download for the SPE is initiated.

-

LOG_STD_NO_ACTION

SPE-6-SM_DEFER_DOWNLOAD

6-Information

SPE [chars] : Firmware download deferred

Firmware download for the SPE is postponed due to active calls.

-

LOG_STD_NO_ACTION

SPE-3-ST_EVENT_NO_MEM

3-Error

PM ST failed to create [chars].

Port Management failed to allocate dynamic chunk memory for event logging.

port-mgmt

LOG_STD_ACTION

SPE-3-ST_API_ERR

3-Error

PM failed to create [chars].

Port Management failed to initialize the CSM event processing component.

-

LOG_STD_ACTION

SPE-4-SPE_CONFIG_WARN

4-Warning

Country Code Trunk card mismatch for.

A Country Code was configured that may not work with the trunk Card.

-

LOG_STD_NO_ACTION

SPE-4-SPE_ACT_SESS_WARN

4-Warning

Active session count = [dec]. Country code not set

Country code cannot be set on a system with active sessions.

-

LOG_STD_NO_ACTION

SPE-3-MSMGR_REGISTRATION_ERR

3-Error

Failed to register [chars] with Modem Service Manager

Port Management failed to register with Modem Service Manager.

-

LOG_STD_NO_ACTION

SPE-3-PM_DIRECT_MODEM_QUERY_ERR

3-Error

Failed to find the response buffer for modem [chars] command

Modem direct query responses could not find buffer to send data to router shelf.

-

LOG_STD_NO_ACTION

SPE-3-PM_SLOT_NO_MODULES

3-Error

Database reported 0 modules for slot [dec]

The card in this slot should contain multiple modules. However the database indicates that there are none.

-

LOG_STD_NO_ACTION

SPE-3-PM_DB_NO_MEM

3-Error

Failed to allocate [chars] for slot [dec]

Port Management failed to allocate memory to create slot object.

-

LOG_STD_NO_ACTION

PORT-6-NULL_OBJ

6-Information

Port object [chars] is unavailable.

Information about this port could not be retrieved. The port may not exist.

-

LOG_STD_NO_ACTION

PORT-6-SM_PORT_CLEARED

6-Information

[chars]

The ports will be reset and any active calls on these ports will be terminated

-

LOG_STD_NO_ACTION

MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD

6-Information

[chars]

Terse Modem Call Record

port-mgmt

LOG_STD_NO_ACTION

MODEMCALLRECORD-6-PM_TERSE_CALL_FAILED_RECORD

6-Information

[chars]

Terse Modem Call Failed Record

port-mgmt

LOG_STD_NO_ACTION

MODEMCALLRECORD-3-PM_CALL_RECORD_ERROR

3-Error

[chars]

Record Generated Exceeded Syslog Capability

port-mgmt

LOG_STD_NO_ACTION

MODEMCALLRECORD-3-PM_NO_CALL_RECORD_BUF

3-Error

[chars]

The Recovery Download Maintenance messages cannot be sent.

port-mgmt

LOG_STD_ACTION

PORT-6-PORT_RECOVERY

6-Information

[chars] [chars]

Recovery has been triggered. Configured action will take place on \n\ the port

-

LOG_STD_NO_ACTION

PORT-6-SESSION_RECOVERY

6-Information

[chars] [chars] [dec]

Session recovery has an invalid cause code

-

LOG_STD_NO_ACTION

SPE-6-SPE_DNLD_MAINT

6-Information

[chars] [chars]

Download maintenance is running and information

-

LOG_STD_NO_ACTION

SPE-6-SPE_DNLD_MAINT_PROCESS

6-Information

[chars]

Download maintenance process information

-

LOG_STD_NO_ACTION

PPPOE_IA-3-GLOBAL_ERROR

3-Error

PPPoE IA internal error [chars]

A software sanity check failed in the PPPoE IA process as described in the output. This happens when the PPPoE IA feature receives a packet with an invalid source interface or source VLAN. PPPoE IA drops the packet but is otherwise unaffected.

cat4000-me-sw

"Issue the show running-config show pppoe intermediate-agent info " "and debug pppoe intermediate-agent command to gather more data " "about the error. If necessary contact Cisco technical support " "to help solve the problem."

PPPOE_IA-3-INTERFACE_ERROR

3-Error

PPPoE IA internal error Interface [chars] : [chars]

A software sanity check failed on an interface in the PPPoE IA process. This message is displayed if PPPoE IA received a packet it shouldn't according to the configuration. PPPoE IA drops the packet but is otherwise unaffected.

cat4000-me-sw

"Issue the show running-config show pppoe intermediate-agent info " "and debug pppoe intermediate-agent command to gather more data " "about the error. If necessary contact Cisco technical support " "to help solve the problem."

PPPOE_IA-4-ERRDISABLE_WARNING

4-Warning

PPPoE IA received [dec] PPPoE packets on interface [chars]

PPPoE IA detected a PPPoE packet rate limit violation on the specified interface. The interface will be error disabled.

cat4000-me-sw

LOG_STD_NO_ACTION " To recover the disabled interface use the " "errdisable recovery cause pppoe-ia-rate-limit command"

PPPOE_IA-4-QUEUE_FULL

4-Warning

Fail to enqueue PPPoE packet into processing queue: [chars] the queue is probably full and packet will be dropped.

PPPoE packets are being received at a much higher rate than PPPoE IA process can handle them. These unhandled PPPoE packets will be dropped to prevent a possible denial of service attack.

cat4000-me-sw

LOG_STD_NO_ACTION

PPPOE_IA-4-RATE_LIMIT_EXCEEDED

4-Warning

The interface [chars] is receiving more than the threshold set

PPPoE packets are being received at a much higher rate than the specified threshold.

cat4000-me-sw

LOG_STD_NO_ACTION

PPPOE_IA-5-UNTRUSTED_PORT

5-Notice

[chars] drop message on untrusted port message type: [chars] MAC sa: [enet]

PPPoE IA detected types of PPPoE messages that are not allowed on the untrusted interface. A host may be trying to act as a PPPoE server.

cat4000-me-sw

LOG_STD_NO_ACTION

PT-3-BADSCOPERATION

3-Error

Invalid [chars] of subcommand [dec] on ruleset %S.

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

PT-3-BADRULEUNLOCK

3-Error

Invalid unlock on ruleset %S [chars].

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

PT-3-BADRULEDELETE

3-Error

Error deleting ruleset %S [chars].

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

PT-3-NOOPERATION

3-Error

No [chars] operation defined for [chars] parameter [chars].

An internal data consistency error has been detected.

-

"Call your technical support representative for assistance."

PT-6-INVOPERATION

6-Information

An invalid [chars] operation defined for [chars] parameter [chars].

A parameter evaluation error was detected for the specified ruleset\n\ operation and line.

-

"Call your technical support representative for assistance."

PT-3-PARAMRESULTERR

3-Error

PT ruleset %S protocol [chars] parameter [chars] parse error: [chars].

The final value of a ruleset's protocol/parameter string could not\n\ be decoded.

-

"Review the ruleset elements that set the parameter value to determine\n\ if they need to be modified to generate a valid result."

PT-3-PARAMRESULTINVALID

3-Error

PT ruleset %S protocol [chars] parameter [chars] invalid: [chars].

A protocol parameter value generated by a ruleset was modified\n\ to be valid for protocol translation operation.

-

"Review the ruleset processing for the identified parameter to\n\ determine if it needs to be modified to generate a value that\n\ is for example within the range of values supported for PT."

PT-6-RULESETLIMIT

6-Information

Ruleset [chars] refused an incoming connection due to the max-user limit.

An incoming connection attempt that would normally be processed\n\ by a Protocol Translation ruleset has been refused because of the\n\ ruleset's configured max-user limit.

-

"The network administrator may need to verify that the ruleset\n\ max-user limit is appropriate."

PT-6-RULESETACCESS

6-Information

Ruleset [chars] refused an incoming connection due to the access-class.

An incoming connection attempt that was matched by a\n\ Protocol Translation ruleset has been refused because the source\n\ address failed the ruleset's configured access-class test.

-

"The network administrator may need to verify that the ruleset\n\ access-class configuration is appropriate."

PTRANSFORM-3-PROTO_VER_INCOMPAT

3-Error

Version of local Ptransform \nclient [chars] is incompatible with remote version [chars].

The protocol versions of the local and remote clients are\n\ incompatible. These clients can not communicate with each\n\ other.

-

"Use 'show version' and 'show ptransform clients' to help\n\ verify that the software images are incompatible. Upgrade\n\ the software images on each unit to versions that are \n\ compatible. " LOG_STD_RECUR_ACTION

QBM-3-QBM_CONSISTENCY

3-Error

QBM internal error: [chars]

An action attempted by the QoS Bandwidth Manager implementation encountered an unexpected software condition

qbm

"Search the Bug Toolkit " BUG_TOOLKIT " for existing bugs and " "upgrade the software if necessary. If there is still a " "problem copy the error message exactly as it appears on the " "console or in the system log. Issue the <CmdBold>show qbm " "client<NoCmdBold> <CmdBold>show qbm pool<NoCmdBold> " "<CmdBold>show running<NoCmdBold> and <CmdBold>show version" "<NoCmdBold> commands to gather data which may help identify " "the nature of the error. Then open a case with the Technical " "Assistance Center via the Internet " TAC_CASE_OPEN " or " "contact your Cisco technical support representative and " "provide the representative with the gathered information."

QOS-3-HA_COLLISION_INVALID

3-Error

Received collision table of type [dec]

The specified type of collision is an invalid value which indicates that the message received on the standby RP contains erroneous data. This is an internal software error which should result in a reload of the standby RP so that the bulk sync of configuration can be sent once more by the active RP.

qos

LOG_STD_ACTION

QOS-3-HA_COLLISION_SIZE

3-Error

Received [chars] message total/unit [dec]/[dec] [chars]

The specified type of collision table has been determined to contain a discrepancy between the total message size and the individual table unit that is being decoded on the standby RP. This is an internal software error which should result in a reload of the standby RP so that the bulk sync of configuration can be sent once more by the active RP.

qos

LOG_STD_ACTION

QOS-3-HA_COLLISION_STRING

3-Error

Received [chars] message length [dec] for string [chars]

The specified type of collision table contains an individual unit within the message which has an incorrectly encoded string which is used to represent the collision which is being synced from the active RP. This is an internal software error which should result in a reload of the standby RP so that the bulk sync of configuration can be sent once more by the active RP.

qos

LOG_STD_ACTION

QOS-3-COLLISION_TYPE

3-Error

Type [dec] is invalid for collision [chars]

The specified type of collision is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error.

qos

LOG_STD_ACTION

QOS-3-COLLISION_DELETE

3-Error

[chars] unable to remove index %08X

The specified type of collision is unable to removed the specified index. This is an internal software error.

qos

LOG_STD_ACTION

QOS-3-COLLISION_COUNT

3-Error

[chars] mismatch count [dec]

The specified type of collision has detected that although there are no collisions present the count of such indicates otherwise. This is an internal software error.

qos

LOG_STD_ACTION

QOS-6-COLLISION_MAX

6-Information

Maximum number of collision entries [dec] reached

The system limit on the number of collision entries used in assigning unique identifiers for policy and class maps et al. has been reached. This indicates that no further configuration of entities which require additional generation of a unique identifier will be possible.

qos

LOG_STD_ACTION

QOS-3-INDEX_EXISTS

3-Error

[chars] attempt to add index %08X [chars]

The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error.

qos

"show cce cp id [collisions]"

QOS-3-INDEX_DELETE

3-Error

[chars] unable to remove index %08X

The specified entity is unable to removed the specified index. This is an internal software error.

qos

LOG_STD_ACTION

QOS-3-BLT_INDEX

3-Error

Failed to assign index for target/policy/class/action [dec]/[dec]/[dec]/[chars]

The configuration of queuing has resulted in the failure to generate an internal unique identifier which represents the queue. This is an internal software error.

qos

LOG_STD_ACTION

QOS-6-RELOAD

6-Information

[chars] reloading [chars]

A synchronization attempt between the active and standby RP peers has failed with the reason indicated. The standby peer is reloaded in an attempt to resynchronize when operating in a stateful redundant mode.

qos

LOG_STD_ACTION

QOS-4-INVALIDBW

4-Warning

interface [chars]: Not enough bandwidth to configure service-policy\n

The issued interface bandwidth is less than the total bandwidth that is required for QoS policy on this interface.\n

-

"There is no user action required.\n"

QOS-6-ACTIVATE

6-Information

Activating service policy [chars] on [chars] in [chars] direction

The interface bandwidth is more than the total bandwidth that is required for QoS policy on this interface.\n

-

"There is no user action required.\n"

QOS-6-NON_AGG_WRED

6-Information

ATM SPA doesn't support true non-aggregate WRED. All non-specified dscp/prec values will be aggregated in default WRED profile

ATM SPA has limited hardware capability which is not enough to support traditional WRED. ATM SPA would support 'limited' non-aggregate WRED for the specified dscp/prec values maximum of 6

-

"There is no user action required.\n"

QOS-6-ACTIVATE_NOHW

6-Information

\nActivating service policy [chars] in [chars] direction

-

-

-

QOS-3-HA_GET_ARG_NUM

3-Error

[chars] Failure in getting event identification\n

QoS configuration can't be synced to the standby\n

-

"Contact your Cisco technical support representative.\n"

QOS-3-HA_BULK_SYNC

3-Error

[chars] Failure in completing bulk sync\n

QoS configuration can't be synced to the standby\n

-

"Contact your Cisco technical support representative.\n"

QOS-3-HA_BULK_SYNC_BEFORE_TIMEOUT

3-Error

[chars] Failure in completing bulk sync before timeout\n

The interface bandwidth is more than the total bandwidth that is required for QoS policy on this interface.\n

-

"There is no user action required.\n"

QOS-3-HA_MISMATCH

3-Error

Bulk sync failed for [chars] collisions space available [dec] buffer [dec]

A synchronization attempt between the active and standby RP peers has failed due to the detection of a mismatch in the source and destination sizes of a buffer used in the transport of the collision information to the standby RP. This is an internal software error.

qos

LOG_STD_ACTION

QOS-3-ISSU_COMP

3-Error

Failed to exchange capability with peer

The attempt to negotiate version capabilities and the exhange of the peer support has failed. This indicates that QoS is unable to support a redundant operation with the standby RP peer.

qos

LOG_STD_ACTION

QOS-3-MAIN_SUB_POLICY

3-Error

FR fragmentation is not supported with interface or sub-interface based policies \n

On Cisco 7500 series routers Frame Relay fragmentation is not supported when service policies are configured on the interface or subinterfaces.

-

"Remove the service policy configuration under the interface " "or subinterfaces and reissue either the class command from " "Frame-Relay DLCI interface configuration mode or the " "frame-relay fragment command from map-class configuration " "mode. \n"

QOS-3-CFGERR

3-Error

interface [chars]: configuration failed\n

Enough memory is not available to configure feature\n

high-ipqos

"It is not possible to configure issued command feature unless "

QOS-3-VTEMP_MLP_ERR

3-Error

A service policy cannot be attached to a PPP virtual-access interface when ppp multilink is enabled. A service policy can be attached to a ppp multilink bundle interface only.\n

A service policy attached to a virtual-template is usually copied to associated virtual-access interfaces. However if such a virtual-access interface joins a multilink ppp bundle the policy is not attached to the virtual-access interface.\n

qos

"This is informational message. No action is required\n"

QOS-3-VTEMP_VC_ERR

3-Error

Attaching a service policy to a PPP/PPPoE virtual-access interface is not allowed when another policy is already attached to the vc/pvc to which the PPP/PPPoE virtual-access interface is bound.\n

Attaching a service policy to a PPP/PPPoE virtual-access interface is not allowed when another policy is already attached to the vc/pvc to which the PPP/PPPoE virtual-access interface is bound.\n

qos

"Remove the policy attached to the vc/pvc before attaching " "a new policy to a PPP/PPPoE virtual-access interface\n"

QOS-3-HQF_FEA_API_FAIL

3-Error

Feature processing API returned NULL pak with INCOMPLETE flag\n

HQF calls feature processing API to get the next packet from the feature for example Frame-relay fragmentation. The API returns conflicting flags with NULL packet.\n

qos

"Check if the system resources e.g. packet buffers are exhausted." " Contact technical support\n"

QOS-3-VTEMP_SUB_ERR

3-Error

Attaching a service policy to a PPP/PPPoE virtual-access interface is not allowed when another policy is already attached to the subinterface to which the PPP/PPPoE virtual-access interface is bound.\n

Attaching a service policy to a PPP/PPPoE virtual-access interface is not allowed when another policy is already attached to the subinterface to which the PPP/PPPoE virtual-access interface is bound.\n

qos

"Remove the policy attached to the subinterface before attaching " "a new policy to a PPP/PPPoE virtual-access interface\n"

QOS-3-VTEMP_MAIN_ERR

3-Error

Attaching a service policy to a PPP/PPPoE virtual-access interface is not allowed when another policy is already attached to the main interface to which the PPP/PPPoE virtual-access interface is bound.\n

Attaching a service policy to a PPP/PPPoE virtual-access interface is not allowed when another policy is already attached to the main interface to which the PPP/PPPoE virtual-access interface is bound.\n

qos

"Remove the policy attached to the main interface before attaching " "a new policy to a PPP/PPPoE virtual-access interface\n"

QOS-3-HQFPOOLERR

3-Error

interface [chars]: failed to allocate hqf particle\n

The HQF particle pool is empty. It cannot process a router generated packet\n

-

"Collect show buffer and show policy interface output and send " "to technical support\n"

QOS-3-HQFNOPAK

3-Error

interface [chars]: pak_reparent failed\n

pak_reparent has been invoked and failed.\n

-

"Collect show buffer and show policy interface output and send " "to technical support\n"

QOS-3-MULTIPLE_INTERFACES

3-Error

Load-sharing mode has changed. \ Queuing functionality may not be supported after this.\n

Dynamic interface has changed its route out of different physical interface. It might resolve into multiple interfaces for queuing. HQF functionality will get affected.\n

qos

"Likely scanario is that CEF is returning multiple paths " "across different interfaces. For those tunnels " "which has queuing features need unique out-going interface " "to resolve queuing hierarchy. " "Common instance is per-prefix load-balancing to per-destination. " "Need to remove offending configurations. " "May also need reload to get the queuing in working state\n"

QOS-3-ATLEAST_ONE_FAILOVER_ERR

3-Error

Fail-over of dynamic interface [chars] failed\n

Dynamic interface has changed its route out of different physical interface and queueing can not set-up data-sructures for that new physical interface\n

qos

"One possibility is that new physical interface already has " "service-policy or some other dynamic interface already has " "queueing data-structures associated with that physical interface " "and conjuction of such service-policies are not allowed. " "Remove one or the other service-policy in that case. If that is " "not the case then contact technical support\n"

QOS-3-HQFPAKREQUEUE

3-Error

interface [chars]: pak_requeue_head has been invoked\n

pak_requeue_head function has been invoked on a packet.

qos

"Collect show buffer and show policy interface output and send " "to technical support\n"

QOS-3-INVALID_POLICY

3-Error

queueing policy at session/tunnel can co-exist only with \ class-default shaping policy at sub-interface/pvc\n

There already may be user-defined flat policy or hierarchical policy at the sub-interface/pvc. With existing of such policy no queueing policy is allowed on session\n

qos

"Make sub-interface/pvc based policy just one level policy with only " " class-default\n"

QOS-3-COEX_NOT_ALLWD

3-Error

queueing policy at session cannot co-exist with service policy at sub-interface/pvc\n

There already may be user-defined flat policy or hierarchical policy at the sub-interface/pvc. With existing of such policy no queueing policy is allowed on session\n

qos

"Remove the policy attached to the sub-interface/pvc before attaching " "a new policy to a session\n"

QOS-3-BURST_BC_ERR

3-Error

Burst Bc increased to [dec] bytes\n

If Burst BC is less than the default burst size then Burst Bc is increased to AF_DEAFULT_BURST\n

-

"This is informational message. No action is required\n"

QOS-3-HQF_QID_ERR

3-Error

Maximum number of QoS queues [dec] reached.\n

The system has run out of QoS queue identifiers and cannot allocate any more until existing queues are freed up.\n

-

"Existing QoS configurations will need to be removed to free up" "more queue identifiers. For example remove existing QoS " "service-policy configurations or modify policy-map templates to " "have fewer queueing actions.\n"

QOS-4-LC_STATS_MSG_DROPPED

4-Warning

QoS statistics update message dropped due to [chars]\n

Changes to QoS counters are sent periodically from linecards to the route processor. One of these statistics update messages was discarded because it was inconsistent or because the route processor ran out of message buffers. The packet and bytes counters for a single service-policy may be underreported by show commands and SNMP queries.\n

qos

"This is an informational message only." "No action is required.\n"

QOS-3-XDRLEN

3-Error

Invalid XDR length. Type [dec][chars]. XDR/buffer len [dec]/[dec]

An internal software error occured\n

qos

LOG_STD_ACTION

QOS-3-BADXDRSLOT

3-Error

Invalid XDR slot. Type/len/slot [dec]/[dec]/[chars]. XDR at 0x%08x

Configured extended burst size is less than the Rate. It is considered to be illegal and has been reset based on the Rate.\n

qos

"This is an informational message only." "No action is required.\n"

QOS-4-FO_IN_USE

4-Warning

Releasing feature object with reference count [dec]

This is an internal software error. A QoS policy feature object has a stale reference.

qos

"If the message recurs try to isolate the traffic conditions which " "trigger the message and contact technical support. Provide the output " "from the show tech-support and show policy-map interface commands."

QOS-3-SA_SESSION_FAILOVER_ERR

3-Error

Fail-over of dynamic SA session to interface [chars] failed\n

Dynamic SA session has changed its route out of different physical interface and queueing can not set-up data-sructures for that new physical interface\n

qos

"One possibility is that new physical interface already has " "service-policy with queueing configured" "Remove the other service-policy in that case. If that is " "not the case then contact technical support\n"

QOS-4-DYN_SUSPEND

4-Warning

Queueing hierarchy move failed on [chars] suspending policy.

A forwarding path change has moved the given queue to a new port where its QoS queuing policy cannot be satisfied. This is likely due to a conflicting policy or insufficient bandwidth on the new port or simply that a new port has not yet been calculated. The policy has thus been temporarily suspended.

-

LOG_STD_ACTION

QOS-6-DYN_INSTALL

6-Information

Installing suspended policy on [chars].

IOS is restoring a previously suspended policy.

qos

LOG_STD_ACTION

QOS-4-WRED_QLIMIT_OUT_OF_SYNC

4-Warning

On interface [chars] user-defined wred max threshold higher than default queue-limit \n

The user defined random-detect is greater that the default queue-limit for this interface. Some of the random-detect configurations will not function properly due to this anomaly. \n

qos

"No action required this is user configured behavior and " "user should change the configured random-detect value if this " "message if of concern to them.\n"

QOS-4-HQUEUE_QLIMIT_VALUE_SYNC_ISSUE

4-Warning

The hold-queue value is less than the sum of queue-limit values. \n

The hold-queue value is less than the queue-limit configured. This will lead to no-buffer drops instead of tail drops

qos

"The hold-queue value should be properly adjusted to prevent " "no-buffer drops."

QOS-4-QLIMIT_HQUEUE_VALUE_SYNC_ISSUE

4-Warning

The sum of all queue-limit value is greater than the hold-queue value. \n

The hold-queue value is less than the queue-limit configured. This will lead to no-buffer drops instead of tail drops

qos

"The hold-queue value should be properly adjusted to prevent " "no-buffer drops."

QOS-6-RADIO_MULTI_REM

6-Information

Remove [chars] policy before removing policy from [chars]\n

-

-

-

QOS-6-ADAPTIVE_QOS_DISABLED

6-Information

Adaptive QoS functionality is disabled. Shaper is reset to upper-bound

Multiple and consecutive reports from peer are not received. This leads to an assumption that the peer has gone away.

qos

"Removal and re-application of policy may be required to re-enable " "the adaptive QoS functionality"

RAWSOCKET-6-SERVER_REMOVED

6-Information

tty [dec] : raw-socket tcp server removed

The raw-socket tcp server is removed when \n\ certain configuration changed.

wolfeisland-sw

"This is an informational message only. It occurs\n\ in normal operation"

RAWSOCKET-6-CLIENT_REMOVED

6-Information

tty [dec] : raw-socket tcp clients removed

-

wolfeisland-sw

"This is an informational message only. It occurs\n\ in normal operation"

RAWSOCKET-3-NULL_TTY

3-Error

NULL tty line

An internal software error occured. \n\ It could be a temporary condition.

wolfeisland-sw

"Log DDTS if condition is persistent" LOG_STD_ACTION

RAWSOCKET-3-NULL_IDB

3-Error

NULL hardware IDB

An internal software error occured. \n\ It could be a temporary condition.

wolfeisland-sw

"Log DDTS if condition is persistent" LOG_STD_ACTION

RAWSOCKET-3-INIT_FAIL

3-Error

Rawsocket failed to start a process

Rawsocket failed to start a process.

wolfeisland-sw

LOG_STD_ACTION

RAWSOCKET-3-MALLOC_FAIL

3-Error

Rawsocket malloc error for tty line data structure

Rawsocket failed to allocate memory for tty line.

wolfeisland-sw

LOG_STD_ACTION

RAWSOCKET-3-FPGA_FAIL

3-Error

tty [dec] : Failed to set [chars] in FPGA

The software failed to configure FPGA for serialim\n\ it could be a temporary condition.

wolfeisland-sw

"Retry CLI command" LOG_STD_ACTION

RAWSOCKET-3-NULL_INPUT

3-Error

NULL Inputs

An internal software error occured. \n\ It could be a temporary condition.

wolfeisland-sw

"Log DDTS if condition is persistent" LOG_STD_ACTION

RAWSOCKET-3-CLIENT_DISCONNECTED

3-Error

raw-socket tcp client [chars]/[dec] disconnected on tty [chars]

-

wolfeisland-sw

"This is an informational message only. It occurs\n\ in shut operation"

RAWSOCKET-3-CLIENT_CONNECTED

3-Error

raw-socket tcp client [chars]/[dec] connected on tty [chars]

-

wolfeisland-sw

"This is an informational message only. It occurs\n\ in no shut operation"

MDR_SM_LC-3-INIT_FAIL

3-Error

Initialisation error '[chars]'

During MDR SM initialisation an error has occurred that has rendered the MDR SM inoperable. an MDR operation will likely result in the resetting of this line card

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-NOTIFY_TIMEOUT

3-Error

Notification timeout for client [chars][dec] in state [chars]

During MDR SM state transition the notification timer expired for the client. Any MDR operation will likely result in the resetting of this line card

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-ABORT

3-Error

MDR state machine is aborted due to '[chars]'

MDR state machine is aborted due to an unrecoverable error. Any MDR operation will likely result in the resetting of this line card

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-SEMWAIT

3-Error

MDR state machine waiting for semaphore[chars] acquired by pid[dec]

SEMWAIT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-INVALID_EVENT

3-Error

MDR SM LC received an unexpected event [chars] in state [chars]

INVALID_EVENT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-ID_MISMATCH

3-Error

Client ID mismatch during progression on client: [dec] expecting [dec]

ID_MISMATCH_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-STATUS_INVALID

3-Error

Client [chars] [dec] returned an unexpected status code [dec]

STATUS_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-3-NO_FREE_EVENT_IN_QUEUE

3-Error

The event queue is full for MDR SM MDR SM will abort

NO_FREE_EVENT_IN_QUEUE_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_LC-4-CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM LC client [chars] [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_PROXY-3-NOTIFY_TIMEOUT

3-Error

Notification timeout on MDR [chars] state machine for the remote client '[chars]'

MDR SM Proxy master is unable to communicate with its slave. It did not get any answer to the notification on the slave. An error has occurred that has rendered the MDR SM inoperable. An MDR operation will likely result in the resetting of all Line Cards.

mdr-sm

LOG_STD_ACTION

MDR_SM_PROXY-4-SYS_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM SYS client [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM_PROXY-4-SLOT_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM Slot [dec] client [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-INIT_FAIL

3-Error

Initialisation error '[chars]'

During MDR SM initialisation an error has occurred that has rendered the MDR SM inoperable. an MDR operation will likely result in the resetting of all Line Cards.

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-QUIESCE_FAIL

4-Warning

Quiesce watchdog timer expired continuing with MDR

At switchover on the old Active RP the MDR SM enters the Quiesce state. While this is occuring the reload of the old Active is blocked which in effect blocks the switchover from taking place. Therefore to prevent a loss of service due to a bug in the MDR SM or one of its clients a watchdog timer ensures that we won't stay in this state for too long.

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-UNBLOCK_RF

4-Warning

MDR SM aborted continuing RF Progression [dec]

The MDR State Machine aborts due to a bug in the MDR State Machine or one of its clients. The RF progression was blocked it will be unblocked to allow the standby to boot

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_NO_FREE_EVENT_IN_QUEUE

3-Error

The event queue is full for MDR System SM MDR SM will abort

NO_FREE_EVENT_IN_QUEUE_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_NO_FREE_EVENT_IN_QUEUE

3-Error

The event queue is full for MDR Slot SM [dec] MDR Slot SM [dec] will abort

NO_FREE_EVENT_IN_QUEUE_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_NOTIFY_TIMEOUT

3-Error

Notification timeout on MDR system state machine for the local client [chars] [dec] in state [chars]

NOTIFY_TIMEOUT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_NOTIFY_TIMEOUT

3-Error

Notification timeout on MDR slot state machine [dec] for the local client [chars] [dec] in state [chars]

NOTIFY_TIMEOUT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_EVENT_TIMEOUT

3-Error

MDR slot state machine [dec] did not receive the SLOT_UP event from the linecard

Slot MDR SM did not get an expected event form the linecard. This error has rendered this slot MDR SM inoperable

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_CLIENT_ID_ERROR

3-Error

Can not find the data associated to client ID [dec]

CLIENT_ID_ERROR_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_CLIENT_ID_ERROR

3-Error

Can not find the data associated to client ID [dec] for slot [dec]

CLIENT_ID_ERROR_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_STATUS_INVALID

3-Error

Client [chars] [dec] returned an unexpected status code [dec]

STATUS_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_STATUS_INVALID

3-Error

Client [chars] [dec] on slot [dec] returned an unexpected status code [dec]

STATUS_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_CONTINUE_INVALID

3-Error

Client [dec] returned an invalid status code

CONTINUE_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_CONTINUE_INVALID

3-Error

Client [dec] returned an invalid status code on slot [dec]

CONTINUE_INVALID_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_ID_MISMATCH

3-Error

Client ID mismatch during progression [chars] on client: [dec] expecting [dec]

ID_MISMATCH_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_ID_MISMATCH

3-Error

Client ID mismatch for slot [dec] during progression [chars] on client: [dec] expecting [dec]

ID_MISMATCH_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_NOTIFY_STANDBY_FAILED

3-Error

Failed to notify Standby for MDR system state machine Client [chars] [dec] in state [chars]

NOTIFY_STANDBY_FAILED_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_NOTIFY_STANDBY_FAILED

3-Error

Failed to notify Standby for MDR slot state machine [dec]

NOTIFY_STANDBY_FAILED_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SYS_INVALID_EVENT

3-Error

Received an unexpected event [chars] in state [chars]

INVALID_EVENT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_INVALID_EVENT

3-Error

Slot [dec] received an unexpected event [chars] in state [chars]

INVALID_EVENT_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-3-SLOT_INVALID_ARG

3-Error

Process is unable to get his slot number

MDR State Machine creates one process per slot \ supporting MDR. In that case the process is \ unable to get his slot.

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-SYS_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM SYS client [chars] [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

MDR_SM-4-SLOT_CALLBACK_TOO_MUCH_TIME

4-Warning

MDR SM Slot [dec] client [chars] [dec] spent too much time [dec] msecs in \

CALLBACK_TOO_MUCH_TIME_EXPLANATION

mdr-sm

MDR_SM_LOG_STD_ACTION

COMP_MATRIX-4-DISABLED

4-Warning

Compatibility Matrix has been disabled. No image compatibility checking will be done.

The ISSU compatibility matrix check has been disabled via configuration command <cmdBold>no service image-version compatibility<noCmdBold>. When the standby comes up no image compatibility checking will be done which results in SSO redundancy mode even if the active and standby are running different images.

ha-issu-infra

"The ISSU compatibility matrix check has been disabled " "using the global configuration command " "<cmdBold>no service image-version compatibility<noCmdBold>." "Redundancy mode would be SSO. " "Please be sure this is your intention or change configuration " "using <cmdBold>service image-version compatibility<noCmdBold>."

COMP_MATRIX-3-PRST_VBL_GET

3-Error

ISSU Compatibility Matrix was unable to read a persistent variable from the local system rc = [dec].

The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled.

ha-issu-infra

"show persistent variable"

COMP_MATRIX-3-PRST_VBL_DELETE

3-Error

ISSU Compatibility Matrix was unable to delete a persistent variable from the [chars] system rc = [dec].

The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled.

ha-issu-infra

"show persistent variable"

COMP_MATRIX-3-PRST_VBL_WRITE

3-Error

ISSU Compatibility Matrix was unable to write to persistent variables on the [chars] system rc = [dec].

The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled.

ha-issu-infra

"show persistent variable"

HA_CLIENT-3-CLIENT_INIT_FAILED

3-Error

Initialisation of the [chars] HA client failed required fields missing

The HA client utilities code could not initialise the specified client because some fields required by the utilities code were not provided by the client. This should not happen and suggests a software problem.

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-RF_REG_FAILED

3-Error

RF registration for the [chars] HA client failed with return code [dec]

The specified HA client failed to register properly with the Redundancy Facility RF. This should not happen and suggests

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-CF_REG_FAILED

3-Error

CF registration for the [chars] HA client failed with return code [dec]

The specified HA client failed to register properly with the Checkpointing Facility CF. This should not happen and suggests

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-4-CF_NOT_BUNDLED

4-Warning

CF failed to go into bundled mode for the [chars] HA client rc [dec]

The Checkpointing Facility CF did not allow the specified HA

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-NO_BS_PROCESS

3-Error

The [chars] HA client failed to create a Bulk Sync process rc [dec]

The nominated HA client could not create an IOS process that it needed in order to perform its Bulk Sync. This means the client's Bulk Sync did not occur. Hence the Standby unit is now out-of-sync. This should not occur and should be reported.

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-CP_TO_STBY_FAILED

3-Error

Delivery of a checkpointing CP message from the [chars] HA client failed

The nominated HA client on the Active unit was told by the Checkpointing Facility CF that one of its checkpointing messages

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-BS_TO_STBY_FAILED

3-Error

The [chars] HA client's Bulk Sync phase was unsuccessful

The nominated HA client could not get a buffer from the Checkpointing Facility CF in which to put some checkpointing

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-NO_RF_BUFFER

3-Error

The [chars] HA client failed to get a buffer len=[dec] from RF

-

-

-

HA_CLIENT-3-RF_MSG_NOT_SENT

3-Error

Delivery of an RF message from the [chars] HA client failed rc=[dec]

The nominated HA client was told by the Redundancy Facility RF

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-PROTO_VER_INCOMPAT

3-Error

The HA client '[chars]' is incompatible with the peer

The named HA client can not communicate with the client on the peer unit. These units can not be used in a warm or hot standby environment.

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-4-RESOURCE_RECOVERY_LIST_FAILURE

4-Warning

Failed to create [chars] resource recovery list

The specified resource recovery list could not be created. This means resource recovery cannot be performed upon switchover which will most likely leave some of the relevant resources unusable. This should not normally happen and should be reported.

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-VALIDITY_CHECK_FAILURE

3-Error

The HA client detected a validity check failure: [chars]

The HA client performed a validity check. This check failed and may indicate a serious problem. A reload may be required to recover from this situation

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-3-IF_INDEX_ADD_FAILURE

3-Error

Unable to add an interface index to a table: [chars] rc=[dec]

The interface index could not be added to a table. This should not normally happen and should be reported.

as5850-redundancy

LOG_STD_ACTION

HA_CLIENT-4-IF_INDEX_LOOKUP_FAILURE

4-Warning

Unable to find an interface index: rc=[dec] [chars]

The interface index could not be found. This is a rare but possible situation and it should be able to correct itself.

as5850-redundancy

LOG_STD_NO_ACTION

REDUNDANCY_UTILS-3-INVALID_UNIT_DESIGNATION

3-Error

An invalid redundancy designation [chars] has been detected.

The redundancy utility assigns each system a unit designation of either an Active Unit Standby Unit or Other Unit and this designation was found to be invalid in the run-time module associated with the system traceback message. This condition most likely occurred because of a software error. The message text provides more information on the specific nature of the error.

rep

LOG_STD_ACTION

REP-3-NOPPPROC

3-Error

Failed to create REP LSL Fast Hello Process

-

rep

-

REP-5-EDGEMISCONFIG

5-Notice

Invalid topology. More than two edge ports configured for segment [dec]

-

rep

LOG_STD_ACTION

REP_ISSU-3-INIT

3-Error

REP ISSU client initialization failed at [chars] error [chars]

REP ISSU client could not be initiailzed this will cause catastrophic failure when ISSU upgrade or downgrade is performed.

rep

LOG_STD_SH_TECH_ACTION

REP_ISSU-3-TRANSFORM

3-Error

REP ISSU client [chars] transform failed error [chars]

REP ISSU client could not transform the message. If the transmit transformation failed it means that the checkpoint message can not be sent to the standby unit. If the receive transformation failed it means that the checkpoint message can not be applied on the standby unit. In both cases the Port Manager state will not be identical with the active unit.

rep

"show issu session <client_id> and" "show issu negotiated version <session_id>"

REP_ISSU-3-MSG_NOT_OK

3-Error

REP ISSU client message [dec] is not compatible

REP ISSU client received an incompatible message from the peer unit. Since the message is not compatible it can be processed by this unit

rep

"show issu message group <client_id> and" "show issu session <client_id> and" "show issu negotiated version <session_id>"

REP_ISSU-3-MSG_SIZE

3-Error

REP ISSU client failed to get the message size for message [dec]

REP ISSU client failed to calculate message size for the message specified. The REP ISSU client will not be able to send message to the standby unit.

rep

"show issu message group <client_id> and" "show issu session <client_id> and " "show issu negotiated version <session_id>"

REP_ISSU-3-SESSION

3-Error

REP ISSU client [chars]

REP ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up.

rep

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

REP_ISSU-3-SESSION_UNREGISTRY

3-Error

REP ISSU client failed to unregister session information. Error: [dec] [chars]

The REP ISSU client failed to unregister session information.

rep

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

REP_ISSU-3-SEND_FAILED

3-Error

REP ISSU client failed to send a negotiation message error [dec]

REP ISSU client could not send a session negotiation message to the peer. When there is a problem in the negotiation the standby unit can not be brought up.

rep

"show logging and show checkpoint client"

REP_ISSU-3-BUFFER

3-Error

REP ISSU client failed to get buffer for message error [dec]

REP ISSU client failed to get buffer for building a negotiation message. Hence it can send the negotiation message to the standby unit. When there is a problem in the negotiation the standby unit can not be brought up.

rep

"show logging and show checkpoint client"

REP_ISSU-3-CAPABILITY

3-Error

REP ISSU client [chars]

REP ISSU client observed an error during capability negotiation. When this error happens there is a mismatch between the client capability between the active and standby unit.

rep

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

REP_ISSU-3-POLICY

3-Error

REP ISSU client message type [dec] is [chars]

REP ISSU client received an message type which it does not support. The policy is applied to make the session compatible.

rep

"show issu session <client_id>"

RFPROXY-2-NOMEM

2-Critical

No memory available

The RF Proxy subsystem could not obtain the memory \n\ it needed

c7600-ha

LOG_STD_SH_TECH_ACTION

RFPROXY-2-INIT

2-Critical

Initialization failed

The RF Proxy subsystem failed during its \n\ initialization

c7600-ha

LOG_STD_SH_TECH_ACTION

RFPROXY-2-RPC

2-Critical

RPC message failure

The RF Proxy could not send an RPC message.

c7600-ha

-

RLM-4-NOBUF

4-Warning

rlm [dec]: cannot get packet buffer for [chars].

A rlm link cannot allocate a packet buffer.

-

LOG_STD_REDUCE_ACTION

RLM-3-INIT

3-Error

rlm [dec]: [chars][chars].

RLM initialization operation fails.

-

LOG_STD_ACTION

RLM-4-LINK

4-Warning

rlm [dec]: [chars][chars].

A warning is given out for a particular RLM link.

-

LOG_STD_DBG_ACTION

RM-3-WAVL

3-Error

Wavl error

An internal software error.

resource-manager

LOG_STD_ACTION

RM-3-BOUNDARY

3-Error

Memory boundary violation

An internal software error.

resource-manager

LOG_STD_ACTION

RM-3-ZEROVAL

3-Error

Uninitialized value being used

An internal software error.

resource-manager

LOG_STD_ACTION

RM-3-NORESP

3-Error

No response-code from local RM

An internal software error.

resource-manager

LOG_STD_ACTION

RM-3-RGINFO

3-Error

[chars]: RG-info conversion failed [dec].

An internal software error.

resource-manager

LOG_STD_ACTION

RM-3-BADRG

3-Error

Bad state rg \[chars]\: [dec]

An internal software error.

resource-manager

LOG_STD_ACTION

RM-3-BADCALL

3-Error

Unexpected Call on [chars]. Current state is [dec].

A call came in on a line where we think we still have an active call.

resource-manager

LOG_STD_ACTION

RM-3-BADACCT

3-Error

Unknown Accounting type [dec] flag [dec].

Get either invalid accounting type or flag

resource-manager

LOG_STD_ACTION

RM-3-OUTOFBUFFS

3-Error

Out of buffers in RM event buffer queue

An internal software error.

resource-manager

LOG_STD_ACTION

DRMI-3-IPC_ERROR

3-Error

[chars][chars] [hec] rc:[chars]

ERM Framework is experiencing errors when communicating to Line Cards using IPC

rmi

"show ipc ports"

DRMI-3-ISSU_XMIT

3-Error

Client id:[dec] xmit failed error:[dec]

ERM Framework is experiencing Errors when performing ISSU Transformation during a transmit operation

rmi

"show ipc ports"

DRMI-3-ISSU_RCV

3-Error

Client id:[dec] receive failed error:[dec]

ERM Framework is experiencing Errors when performing ISSU Transformation during a receive operation

rmi

"show ipc ports"

DRMI-3-ISSU_ERR

3-Error

[chars] error:[dec]

ERM Framework is experiencing ISSU Errors

rmi

"show ipc ports"

DRMI-3-ISSU_MTU

3-Error

Client id:[dec] MTU failed error:[dec]

ERM Framework is experiencing Errors when performing ISSU GET MTU during a transmit operation

rmi

"show issu nego"

SPAN-3-UNKN_ERR

3-Error

An internal error occurred during a SPAN operation.

SPAN detected an error in its internal operation.

-

"The error might be transient in which case trying the SPAN operation\n\ again might be successful. If this fails the switch might need to be\n\ reloaded for the desired operation to complete."

SPAN-3-UNKN_ERR_PORT

3-Error

An internal error occurred when configuring SPAN on port [chars]

SPAN detected an error in its internal operation.

-

"The error might be transient in which case trying the SPAN operation\n\ again might be successful. If this fails the switch might need to be\n\ reloaded for the desired operation to complete."

SPAN-3-MEM_UNAVAIL

3-Error

Memory was not available to perform the SPAN operation

Unable to perform a SPAN operation because of a lack of memory

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

SPAN-3-SESS_HW_UNAVAIL

3-Error

SPAN hardware resource not available [chars]

The system could not allocate a SPAN hardware resource for the feature specified in the error message. A possible cause of this condition is that all available SPAN source sessions are already in use. The system can be configured with a maximum of two SPAN source sessions or one RSPAN source session

-

"Remove one of the existing SPAN or RSPAN source sessions " "and retry the operation."

SPAN-5-ERSPAN_ADJ_TUNNEL

5-Notice

ERSPAN Destination behind a tunnel. Shutting down session [dec]

The next hop to the IP Address specified as the ERSPAN destination lies behind a tunnel. This configuration is not supported. ERSPAN session is shut down when such configuration is detected

cat6000-l2

"Specify another IP address as the ERSPAN destination which " "does not have tunnel as the next-hop adjacency."

SPAN-6-SPAN_EGRESS_REPLICATION_MODE_CHANGE

6-Information

Span Egress HW Replication Mode Change Detected. Current replication mode for session [chars] is [chars]

When auto detection of egress span replication mode is enabled the system will transition any available sessions to centralized mode when an distributed egress span incapable linecard is inserted. The system will transition back the available sessions to distributed egress span mode when the last distributed egress span incapable linecard is removed

7600-l2

"To prevent a session switching back to distributed egress span" "modeuse the command monitor session egress replication-mode" "centralized"

SPAN-3-REDIR_HW_UNAVAIL

3-Error

Redirect hardware resource not available [chars]

The system could not allocate resource for redirecting BPDUs. A possible cause of this condition is that all available redirect registers in PFC are used by other features.

cat6000-l2

"Free up a redirect register in PFC by unconfiguring features " "that use redirect registers and retry allowing BPDUs for " "SPAN servicemodules. If Protocol Tunneling is configured " "on any ports then remove Protocol Tunneling configuration " "from all ports to free up one redirect register."

SPAN-5-PKTCAP_START

5-Notice

Packet capture session [dec] started

Packet capture is activated by user or after the scheduled time

cat6000-l2

"Stop the capture when it is not required. You can change the rate of " "packets reaching CPU for capturing by configuring the rate-limit value " "in the monitor session type capture config mode. Protocol packets may " "get dropped if the capture traffic rate is high."

SPAN-5-PKTCAP_STOP

5-Notice

Packet capture session [dec] ended [chars] [dec] packets captured

Packet capture is stopped. This will happen if the capture buffer is full or if user stops the capture or if capture timeout happens.

cat6000-l2

"Packet capture is stopped. You can export the capture buffer using " "the 'monitor capture <id> export buffer <url>' command. Buffer can " "be dislayed on the console also. Delete the capture session if it " "is no longer required."

RMON-5-RISINGTRAP

5-Notice

Rising threshold has been crossed because the value of [chars] exceeded the rising-threshold value [dec]

A Rising Event will be generated.The value of the specified\n\ MIB object has exceeded the rising threshold value as configured by\n\ the <CmdBold>rmon alarm<NoCmdBold> command for the specified object

Check the behaviour of the specified MIB object under \n\ observation and investigate the reason for the generation\n\ of the trap.

"Take appropriate action on the specified object."

RMON-5-FALLINGTRAP

5-Notice

Falling threshold has been crossed because the value of [chars] has fallen below the falling-threshold value [dec]

A Falling Event will be generated.The value of the specified\n\ MIB object has fallen below the falling threshold value as\n\ configured by the <CmdBold>rmon alarm<NoCmdBold> command for\n\ the specified object

Check the behaviour of the specified MIB object and\n\ investigate the reason for the generation of the trap.

"Take appropriate action on the specified MIB object."

RMON-5-HCRISINGTRAP

5-Notice

Rising trap is generated because the value of [chars] exceeded the\n\rising-threshold hc value %llu

A Rising Trap has been generated.The value of the specified\n\ MIB object has exceeded the rising threshold value as configured by\n\ the <CmdBold>rmon hc-alarms<NoCmdBold> command for the specified object

Check the behaviour of the specified MIB object under \n\ observation and investigate the reason for the generation\n\ of the trap.

"Take appropriate action on the specified object."

RMON-5-HCFALLINGTRAP

5-Notice

Falling trap is generated because the value of [chars] has fallen below\n\the falling-threshold hc value %llu

A Falling Trap has been generated.The value of the specified\n\ MIB object has fallen below the falling threshold value as\n\ configured by the <CmdBold>rmon hc-alarms<NoCmdBold> command for\n\ the specified object

Check the behaviour of the specified MIB object and\n\ investigate the reason for the generation of the trap.

"Take appropriate action on the specified MIB object."

RPL-3-CONFIG_ERROR

3-Error

RPL [chars] configuration failed: [chars] [chars] code [dec]

This Error message would be encountered when trying to configure rpl through api.

rpl

LOG_STD_ACTION

RPL-3-CHUNK_ERROR

3-Error

[chars]

This Error message would be encountered when trying to 1. access chunk or chunk element when they are not valid. 2. lock failure on chunk element.

rpl

LOG_STD_ACTION

RPL-3-MALFORMEDMSG

3-Error

Malformed [chars] received from: %P

This Error message would be encountered if a malformed RPL Control message is received

-

"Informational"

RPA-3-FLEXIBLE

3-Error

[chars]

This message type is created for all those messages which\n\ have simple ASCII text and does not take any parameter.\n\ Message tells what the problem is.

resource-grp-mgr

LOG_STD_ACTION

RPA-3-UNKNOWN_MSG

3-Error

Unknown message type [dec] enqueued to RPA CAS Process

A message type which is not known to RPA CAS process is\n\ enqueued to it's queue.

resource-grp-mgr

LOG_STD_ACTION

RPA-3-NO_CAS_ENTRY

3-Error

CAS Entry does not exist for slot: [dec] ctrl:[dec] channel:[dec]

CAS entry does not exist for the given controller and channel.

resource-grp-mgr

LOG_STD_ACTION

RPL-3-CONFIG_ERROR

3-Error

RPL [chars] configuration failed: [chars] [chars] code [dec]

This Error message would be encountered when trying to configure rpl through api.

rpl

LOG_STD_ACTION

RPL-3-CHUNK_ERROR

3-Error

[chars]

This Error message would be encountered when trying to 1. access chunk or chunk element when they are not valid. 2. lock failure on chunk element.

rpl

LOG_STD_ACTION

RPL-3-MALFORMEDMSG

3-Error

Malformed [chars] received from: %P

This Error message would be encountered if a malformed RPL Control message is received

-

"Informational"

MPLS_TE_PCALC-3-INIT

3-Error

[chars]

An internal inconsistency was detected during MPLS TE path calculation initialization such as an attempt was made to initialize the MPLS TE path calculation system id before the system_id size is known.

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-3-PATH

3-Error

[chars]

An internal inconsistency was detected when an attempt was made to establish an MPLS TE tunnel using the MPLS TE path calculation subsystem.

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-3-LSA

3-Error

[chars] [chars]

An internal inconsistency was detected when an attempt was made to establish handle received lsa for MPLS TE topology database.

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-2-MEM

2-Critical

[chars] [dec]

A failure at an attempt to alloc memory was detected

mpls-te

LOG_STD_ACTION

MPLS_TE_PCALC-2-DUP_RRR_ID

2-Critical

[chars] [chars] [chars]

Two nodes have the same stable router id

mpls-te

"Find the system that has the duplicate router id and configure a " "different one"

MPLS_TE_PCALC-2-INVLD_RTR_ID

2-Critical

Invalid router id [chars] received from [chars] in fragment %lu

Received an Invalid Router LSA. LSA should not contain a Router id of zero. The cause of this problem may be misconfiguration memory corruption or unexpected behaviour on a router

mpls-te

"Locate the problem router and check the configuration. " "To determine what is causing this problem call " "your Cisco technical support representative for assistance."

MPLS_TE_PCALC-2-INVLD_RTR_FRAGMENT

2-Critical

Router id [chars] received from [chars] in fragment %lu

Received Router ID in multiple fragments

mpls-te

"Locate the problem router and contact your Cisco " "technical support representative for assistance."

MPLS_TE_PCALC-2-DUP_IP_ADDRESS

2-Critical

[chars] [chars] [chars]

Two nodes have the same stable ip address

mpls-te

"Find the system that has the duplicate ip address and configure a " "different one"

MPLS_TE_LM-5-CLEAR_COUNTERS

5-Notice

Clear MPLS TE Link Management counters by [chars]

The MPLS TE Link Management counters have been cleared

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_LM-3-CONSISTENCY

3-Error

[chars]: [chars] [chars] [chars]

An action attempted by the MPLS TE Link Management implementation encountered an unexpected condition

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE_LM-3-LSP_BAD_SWITCHING_TYPE_REQUESTED

3-Error

[chars]: LSP requests switching type [[chars]] unsupported on link [[chars]]

-

-

-

MPLS_TE_LM-3-LSP_BAD_GPID_REQUESTED

3-Error

[chars]: LSP requests G-PID unsupported or invalid

-

-

-

MPLS_TE_LM-3-LSP_BAD_ENCODING_TYPE_REQUESTED

3-Error

[chars]: LSP requests encoding type unsupported or invalid

The indicated TE LSP routed on the indicated interface requested a Switching Type that is unsupported on the interface. The requested value appears in the Generalized Label Request.

mpls-te

"Verify that the head end originating the TE LSP has a Generalized " "Label Request that is specifying a Switching Type acceptable to the " "interface in question. If not alter the head end configuration " "to request an LSP with an appropriate value or cause the LSP " "to be routed on a different interface. " "If this problem still persists copy the error message exactly as " "it appears on the console or in the system log. Please perform " "a search of the Bug Toolkit " BUG_TOOLKIT ". If you need additional " "assistance open a case with the Technical Assistance Center via " "the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Please provide the output of " "<cmdBold>show tech-support<nocmdBold> and a topology diagram " "showing the hops in the LSP marking each hop with the " "vendor/software and identify which hop is the IOS device issuing " "the error message."

MPLS_TE_LM-3-LSP_BAD_ENCODING_TYPE

3-Error

LSP [chars] requesting Encoding Type [[chars]] that is unsupported on interface [chars].

The indicated TE LSP routed on the indicated interface requested an Encoding Type that is unsupported on the interface. The requested value appears in the Generalized Label Request.

mpls-te

"Verify that the head end originating the TE LSP has a Generalized " "Label Request that is specifying an Encoding Type acceptable to the " "interface in question. If not alter the head end configuration " "to request an LSP with an appropriate value or cause the LSP " "to be routed on a different interface. " "If this problem still persists copy the error message exactly as " "it appears on the console or in the system log. Please perform " "a search of the Bug Toolkit " BUG_TOOLKIT ". If you need additional " "assistance open a case with the Technical Assistance Center via " "the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Please provide the output of " "<cmdBold>show tech-support<nocmdBold> and a topology diagram " "showing the hops in the LSP marking each hop with the " "vendor/software and identify which hop is the IOS device issuing " "the error message."

MPLS_TE_LM-3-LSP_BAD_SWITCHING_TYPE

3-Error

LSP [chars] requesting Switching Type [[chars]] that is unsupported on interface [chars].

The indicated TE LSP routed on the indicated interface requested a Switching Type that is unsupported on the interface. The requested value appears in the Generalized Label Request.

mpls-te

"Verify that the head end originating the TE LSP has a Generalized " "Label Request that is specifying a Switching Type acceptable to the " "interface in question. If not alter the head end configuration " "to request an LSP with an appropriate value or cause the LSP " "to be routed on a different interface. " "If this problem still persists copy the error message exactly as " "it appears on the console or in the system log. Please perform " "a search of the Bug Toolkit " BUG_TOOLKIT ". If you need additional " "assistance open a case with the Technical Assistance Center via " "the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Please provide the output of " "<cmdBold>show tech-support<nocmdBold> and a topology diagram " "showing the hops in the LSP marking each hop with the " "vendor/software and identify which hop is the IOS device issuing " "the error message."

MPLS_TE_LM-3-LSP_BAD_GPID

3-Error

LSP [chars] requesting G-PID [[chars]] that is unsupported on interface [chars][chars].

The indicated TE LSP routed on the indicated interface requested a Generalized Payload Identifier unsupported on the

mpls-te

"Verify that the head end originating the TE LSP has a " "Label Request that is specifying a PID acceptable to the " "interface in question. If not one possibility is to alter the " "head end configuration to request an LSP with an appropriate value. " "Alternatively if this error is generated at the penultimate hop of " "an LSP where the endpoint is advertising an implicit-null label " "penultimate hop popping is in use alter the endpoint to "

MPLS_TE_LM-3-GMPLS_UNSUPPORTED_RESOURCE

3-Error

Interface [chars]: GMPLS [chars] labels unsupported

The indicated interface is unable to provide labels of the indicated type.

mpls-te

LOG_STD_SH_TECH_ACTION

MPLS_TE_LM-3-INVALID_LSP

3-Error

A valid LSP must be present for [chars]

A valid LSP is required for this action. This is not a typical occurrence.

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_AUTOMESH-5-AUTOTEMPLATE_HWIDB_DELETE

5-Notice

Failed to delete hwidb for Auto-Template [dec] index [dec]

Deletion of Auto-Template interface failed.

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-3-LOCK_DOUBLE

3-Error

Unexpected data structure access. Non-zero lock count [dec] when [chars] locks [dec] failure[chars].

MPLS_TE_AUTO_TUN_STD_LOCK_EXPLANATION

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-3-LOCK_ZERO

3-Error

Unexpected data structure access. [chars] unlocks with count [dec] but not locked [dec] failure[chars].

MPLS_TE_AUTO_TUN_STD_LOCK_EXPLANATION

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-3-LOCK_COUNT

3-Error

Unexpected data structure access. [chars] unlocks with count [dec] but expected [dec] [dec] failure[chars].

MPLS_TE_AUTO_TUN_STD_LOCK_EXPLANATION

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-4-REMOVE_FAIL

4-Warning

Removing existing auto tunnels may have failed.[chars][chars] MPLS_TE_AUTO_TUN_STD_CONFIRM Use \show running-config\ to confirm expected configuration. Repeat CLI configuration as needed.

The MPLS Traffic Engineering Auto-Tunnel software detected a possible \ problem removing existing automatic tunnels. It may be necessary to \ repeat the CLI action that caused the removal and reconfiguration of \ automatic tunnels.

mpls-te

LOG_STD_ACTION

MPLS_TE_AUTO_TUN-4-CONFLICT_CFG

4-Warning

[chars]

Conflicting MPLS TE auto-tunnel configuration

mpls-te

"Re-check auto-tunnel configuration for P2P Primary Backup and Mesh" "make sure tunnel-id range are not overlapped."

MPLS_TE_HA-3-PROCESS_CREATE_FAILED

3-Error

Failed to create RSVP HA process

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process"

MPLS_TE_HA-3-PROCESS_KILL

3-Error

Killing RSVP HA process

system may be low on memory. Failed to create RSVP HA \n services

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_HA-3-CF_REGISTER_FAILED

3-Error

Failed to register with CF

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-RF_REGISTER_FAILED

3-Error

Failed to register with RF

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-RF_UNREGISTER_FAILED

3-Error

Failed to unregister with RF

RSVP HA client may not have registered with RF

mpls-te

LOG_STD_NO_ACTION

MPLS_TE_HA-3-CLI_ADD_FAILED

3-Error

Failed to add RSVP HA to CLI

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-DB_INIT_FAILED

3-Error

Database init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-MSG_MGR_INIT_FAILED

3-Error

Message Manager init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-ISSU_INIT_FAILED

3-Error

In Service Software Upgrade ISSU Init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-MAIN_INIT_FAILED

3-Error

Main init failed

system may be low on memory

mpls-te

"Verify system memory availability. Then deconfigure \n" "graceful restart full-mode and configure it again. \n" "This will attempt to re-start the RSVP HA process and \n" "re-register with CF"

MPLS_TE_HA-3-ENTRY_MOVE_FAILED

3-Error

Failed to move a database entry to [chars] tree

An attempt to move a data entry from one wavl tree to another wavl tree failed

mpls-te

"This error should never happen under normal " "operation and indicates an internal error. " "Open a ddts"

MPLS_TE_HA-3-ITEM_SIZE_TOO_BIG

3-Error

Item size [dec] bigger than default CF buffer [dec] supported by

A database entry cannot be sent to the standby because the database entry doesn't fit in a CF maximum size buffer allowed by the platform.

mpls-te

"This error indicates a problem with design in " "handling platform dependent restrictions. " "Open a ddts"

MPLS_TE_HA-3-SSO_UNSUPPORTED

3-Error

Attempt to init RSVP HA subsystem when TE SSO not supported

RSVP TE SSO is included in image that doesn't support SSO

mpls-te

"This error indicates a problem with design in. " "Open a ddts"

MPLS_TE_NSR-3-RESEQUENCE_ERROR

3-Error

Error occurred during TE NSR resequence

An unrecoverable error occurred during TE NSR resequence of state

mpls-te

"Disable and then reenable TE NSR functionality and " "open a DDTS"

TENSRFSM-3-NULLMACH

3-Error

Invalid machine pointer 0x%X

state machine invalid pointer

mpls-te

LOG_STD_ACTION

TENSRFSM-3-INVSTATE

3-Error

Invalid current state 0x%X

state machine invalid state

mpls-te

LOG_STD_ACTION

TENSRFSM-3-INVEVENT

3-Error

Invalid event_id 0x%X

state machine invalid event

mpls-te

LOG_STD_ACTION

TENSRFSM-3-INVTRANS

3-Error

obj: [0x%08X] event_id: [0x%08X] er_p: [0x%08X] arg: [0x%08X] session state [chars] -> [chars]

state machine invalid transition

mpls-te

LOG_STD_ACTION

TENSRFSM-3-NOEVENT

3-Error

Unable to apply event 0x%08X

state machine transition failure

mpls-te

LOG_STD_ACTION

TENSRFSM-3-NOPROCID

3-Error

Unable to launch TE NSR FSM Process.

state machine transition process launch failure

mpls-te

LOG_STD_ACTION

RSVP-5-CLEAR_COUNTERS

5-Notice

Clear RSVP message counters by [chars]

The RSVP message counters have been cleared

rsvp

LOG_STD_NO_ACTION

RSVP-5-NO_MATCH_IF_ID_HOP

5-Notice

Received PATH [inet]_[dec]->[inet]_[dec] -

The interface id in the HOP object does not match any of this node's interfaces.

rsvp

"Verify the configuration."

RSVP-3-BAD_RMSG_TIMER

3-Error

Inconsistent RSVP reliable message timer

An error was encountered during validation of the objects in an RSVP \n\ message received by the router.

rsvp

LOG_BAD_RSVP_MSG_ACTION LOG_STD_RSVP_ACTION

RSVP-3-BAD_RSVP_MSG_RCVD_VER

3-Error

RSVP Message had a bad version: [dec]

The router received an RSVP message with the version field set to an\n\ unexpected value.

rsvp

LOG_BAD_RSVP_MSG_ACTION LOG_STD_RSVP_ACTION

RSVP-3-BAD_RSVP_MSG_RCVD_CHECKSUM

3-Error

RSVP Message had a bad checksum: [dec] foo: [dec]

The router received an RSVP message with the checksum field incorrectly\n\ set. Bad checksums would most likely be caused by packet corruption \n\ outside RSVP. Be aware that corruption reported by RSVP might also be\n\ affecting other protocols on the router and might explain other \n\ unexpected non-RSVP protocol behavior. Please attempt to track down the \n\ source of the corruption.

rsvp

LOG_BAD_RSVP_MSG_ACTION LOG_STD_RSVP_ACTION

RSVP-3-BAD_RSVP_MSG_RCVD_TYPE

3-Error

RSVP Message had a bad type: [dec]

The router received an incorrect RSVP message.

rsvp

"Copy the error message exactly as it appears on the console\n\ or in the system log. Issue the <CmdBold>show tech-support rsvp\n\ <NoCmdBold> command to gather data which may help identify the\n\ nature of the error. Then send this information to your Cisco\n\ technical support representative."

RSVP-3- IP_HDR

3-Error

%08x %08x %08x %08x %08x %08x %08x %08x

This is an auxiliary message to several packet-related messages. It\n\ displays the contents of 8 32-bit words immediately following the start \n\ of the IPv4/v6 header in hex format. To decode the information in the\n\ IPv4 and IPv6 headers please refer to RFCs 791 and 2460.

rsvp

"Decode the information in the IPv4 and IPv6 headers to determine the\n\ source of the RSVP message."

RSVP-3- MSG_1

3-Error

%08x %08x %08x %08x %08x %08x %08x %08x

This is an auxiliary message to several packet-related messages. It\n\ displays the contents of the first 8 32-bit words immediately following\n\ the start of the RSVP header in hex format. To decode the \n\ information in the RSVP header please refer to RFC 2205.

rsvp

"If you need additional information about the packet then turn on\n\ <CmdBold>debug ip rsvp dump-messages <msg type> [hex]<NoCmdBold> and try\n\ to capture the bad message. If you use the hex version of this command \n\ you can convert it to pcap format with the offline tool text2pcap and \n\ then view the contents with another offline tool such as ethereal."

RSVP-3- MSG_2

3-Error

%08x %08x %08x %08x %08x %08x %08x %08x

This is an auxiliary message to several packet-related messages. It\n\ displays the contents of the next 8 32-bit words following those that \n\ are printed by the MSG_1 message above in hex format. To decode\n\ the information in these 32-bit words please refer to RFC 2205.

rsvp

"If you need additional information about the packet then turn on\n\ <CmdBold>debug ip rsvp dump-messages <msg type> [hex]<NoCmdBold> and try\n\ to capture the bad message. If you use the hex version of this command \n\ you can convert it to pcap format with the offline tool text2pcap and \n\ then view the contents with another offline tool such as ethereal."

RSVP-3-BAD_RSVP_MSG_RCVD_OBJ_LEN

3-Error

Received a bad RSVP message num objs: [dec] obj len: [dec] msg_len: [dec]

An error was encountered during validation of the objects in an RSVP \n\ message received by the router. The number of objects in the RSVP message \n\ was found to be greater than the maximum expected number or the size of\n\ an object was found to be smaller than the minimum expected size.

rsvp

LOG_BAD_RSVP_MSG_ACTION LOG_STD_RSVP_ACTION

RSVP-3-CONSISTENCY

3-Error

[chars]: [chars] [chars] [chars]

An action attempted by the rsvp implementation encountered\n\ an unexpected condition

rsvp

"Copy the error message exactly as it appears on the console\n\ or in the system log. Issue the <CmdBold>show tech-support rsvp\n\ <NoCmdBold> command to gather data which may help identify the\n\ nature of the error. Then send this information to your Cisco\n\ technical support representative."

RSVP-3-BAD_RSVP_MSG_RCVD_AUTH_NO_SA

3-Error

[chars] message from [inet] discarded: no security association for [inet] - no RSVP security key configured or no memory left.

The router received an RSVP message that contained a secure hash but\n\ dropped the message because the router was not able to create a security\n\ association for the sending system.

rsvp

"Check the configuration on the router to make sure that RSVP has access\n\ to a security key for the sending system. If such a key is configured\n\ then check to see if the router has run out of memory."

RSVP-3-BAD_RSVP_MSG_RCVD_AUTH_DIGEST

3-Error

[chars] message from [inet] discarded - incorrect message digest

The router received an RSVP message that contained a different secure\n\ hash from the one computed by the router. RSVP discarded the message\n\ because the message may have come from an untrusted source.

rsvp

"Check the configuration on the router and the sending system to make\n\ sure they are using the correct security key and secure hash algorithm."

RSVP-3-BAD_RSVP_MSG_RCVD_AUTH_WIN

3-Error

[chars] message from [inet] discarded - seq #%llu outside authentication window

The router received an RSVP message whose authentication sequence number\n\ is less than the lower limit of the out-of-order window. RSVP discarded\n\ the message because an untrusted source may be unsuccessfully\n\msgdef_recommended_action It is possible that a trusted source is sending a burst of reordered\n\ RSVP messages that is too large for the authentication window size. If\n\ you can verify that the source is trusted and its messages are being sent\n\ in large reordered bursts

-

-

RSVP-3-BAD_RSVP_MSG_RCVD_AUTH_DUP

3-Error

[chars] message from [inet] discarded - authentication seq #%llu is a duplicate

The router received an RSVP message with an authentication sequence\n\ number that has already been seen. RSVP discarded the message because an\n\ untrusted source may be unsuccessfully attempting an RSVP message\n\msgdef_recommended_action If you can verify that the source is trusted

-

-

RSVP-3-BAD_RSVP_MSG_RCVD_AUTH_COOKIE

3-Error

[chars] message from [inet] discarded - challenge failed for key ID %*s

The router sent an RSVP message to challenge the untrusted source to\n\ compute a secure hash on a random piece of data and return the hash\n\ with the same data but the source did not return the expected data.\n\ RSVP discarded the response because the untrusted source may be\n\ unsuccessfully attempting an RSVP challenge response replay attack.

rsvp

-

RSVP-3-RSVP_MSG_AUTH_CHALLENGE_TIMEOUT

3-Error

No response to challenge issued to [inet] for key ID %*s

The router sent an RSVP message to challenge the untrusted source to\n\ compute a secure hash on a random piece of data and return the hash\n\ with the same data but the source did not reply. The source may\n\ have crashed or lost its network connection. However it is also\n\ possible that the source was unsuccessfully attempting to replay\n\msgdef_recommended_action If you can verify that the source is trusted

-

-

RSVP-3-RSVP_MSG_AUTH_TYPE_MISMATCH

3-Error

[chars] message from [inet] discarded - authentication algorithm mismatch

The router received an RSVP message from a source that required\n\ authentication but the received message was using the wrong\n\ authentication algorithm.

rsvp

"Issue a <CmdBold>show ip rsvp authentication detail <source><NoCmdBold>\n\ command on the router to display the expected algorithm type. Then find\n\ the source and change its configuration to match."

RSVP-5-RSVP_AUTH_ONE_KEY_EXPIRED

5-Notice

Key ID [dec] in chain [chars] has expired

-

-

-

RSVP-2-RSVP_AUTH_KEY_CHAIN_EXPIRED

2-Critical

All the keys in chain [chars] have expired - please update the key chain now

The router attempted to use a key in an RSVP key chain but discovered\n\ that all the keys in the chain have expired. The router will attempt to\n\ to find another suitable key. If no other suitable per-neighbor key can\n\ be found the router will attempt to use key chain configured for the\n\msgdef_recommended_action Update the key chain by updating the text and expiration time

-

-

RSVP-1-RSVP_AUTH_NO_KEYS_LEFT

1-Alert

No valid keys left for [inet]

The router attempted to use a key in an RSVP key chain but discovered\n\ that all the keys in the chain have expired and no other per-neighbor\n\ or per-interface keys are available for the specified neighbor. The\n\ router will continue to use the last key in the chain rather than\n\ revert to an unauthentication condition. However the specified neighbor\n\ router may start discarding RSVP messages at that point and reservations\n\ with that neighbor may eventually time out.

rsvp

-

RSVP-4-RSVP_AUTH_DUPLICATE_KEY_ID

4-Warning

Key chains [chars] and [chars] contain duplicate key ID [dec]

An attempt is being made to add a new key identifier to a key chain in\n\ the router configuration but RSVP detected that this identifier is found\n\ in another key chain already assigned to RSVP. Since key identifiers must\n\ be unique across all the key chains used by RSVP RSVP will not use the\n\ keys with this identifier in all such key chains. This could cause RSVP\n\ authentication to fail in some cases.

rsvp

"Update the listed key chains so they use different key identifiers."

RSVP-5-RSVP_AUTH_KEY_ACL_CHANGE

5-Notice

Key chain [chars] [chars] for [inet] because ACL \[chars]\ [chars]

The ACL specified in the message text associates the key chain specified\n\ in the message text with a set of RSVP neighbors. RSVP uses the specified\n\ key chain to authenticate each RSVP message exchanged with that set of\n\ RSVP neighbors after the association is configured. Subsequently the\n\ specified ACL has been reconfigured such that the key chain association\n\ is no longer valid for one or more RSVP neighbors in the set. This causes\n\ RSVP to search the configuration for another suitable key chain to use\n\ with those neighbors. If no such key chain is found RSVP will no longer\n\ be able to provide authentication for messages exchanged with those RSVP\n\ neighbors. This causes RSVP to discard RSVP messages from that set of\n\ neighbors. Because this may ultimately lead to loss of RSVP functionality\n\ with those neighbors RSVP generates this system message. This system\n\ message may also be generated if the ACL is subsequently changed so that\n\ it re-associates RSVP neighbors with the specified key chain. If RSVP is\n\ not using another key chain for the set of RSVP neighbors specified by\n\ the ACL RSVP will begin using the specified key chain to exchange\n\ authenticated RSVP messages with that set of RSVP neighbors potentially\n\ restoring RSVP functionality with those neighbors.

rsvp

"If the ACL change unexpectedly caused authentication to be disabled\n\ or enabled for one or more RSVP neighbors undo the ACL change so that\n\ RSVP authentication is not impacted."

RSVP-3-RSVP_MFI_RECOVERY

3-Error

RSVP calculated Recovery Time is longer than TE Rewrite Hold-Time registered with LSD. Some LSPs may not be be recovered.

TE registered a maximum cutover time with the LSD that is less than\n\ the time it may actually take to recover all LSPs. As a result more\n\ than usual traffic loss may occur on some LSPs during recovery

rsvp

"Make note of the number of Checkpointed LSPs in the RSVP HA database by\n\ issuing the command <CmdBold>show ip rsvp high-availability database\n\ internal <NoCmdBold>. This number likely exceeds the hard defined limit\n\ of the number of recoverable LSPs. Provide this information to Cisco\n\ technical support representative."

RSVP_SYNC_ISSU-2-INIT

2-Critical

RSVP_SYNC ISSU client initialization failed to [chars]. Error: [dec] [chars]

The RSVP_SYNC ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

rsvp-sync

LOG_STD_ACTION

RSVP_SYNC_ISSU-3-TRANSFORM_FAIL

3-Error

RSVP_SYNC ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The RSVP_SYNC ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the RSVP_SYNC state between the active device and the standby device is not identical.

rsvp-sync

"show issu session <client_id> and " "show issu negotiated version <session_id>"

RSVP_SYNC_ISSU-3-MSG_NOT_OK

3-Error

RSVP_SYNC ISSU client 'Message Type [dec]' is not compatible

The RSVP_SYNC ISSU client received an incompatible message from the peer device. The message cannot be processed.

rsvp-sync

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

RSVP_SYNC_ISSU-3-MSG_SIZE

3-Error

RSVP_SYNC ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The RSVP_SYNC ISSU client failed to calculate the MTU for the specified message. The RSVP_SYNC ISSU client is not able to send the message to the standby device.

rsvp-sync

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

RSVP_SYNC_ISSU-3-INVALID_SESSION

3-Error

RSVP_SYNC ISSU client does not have a valid registered session.

The RSVP_SYNC ISSU client does not have a valid registered session.

rsvp-sync

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

RSVP_SYNC_ISSU-2-SESSION_REGISTRY

2-Critical

RSVP_SYNC ISSU client failed to register session information. Error: [dec] [chars]

The RSVP_SYNC ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

rsvp-sync

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

RSVP_SYNC_ISSU-3-SESSION_UNREGISTRY

3-Error

RSVP_SYNC ISSU client failed to unregister session information. Error: [dec] [chars]

The RSVP_SYNC ISSU client failed to unregister session information.

rsvp-sync

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

RSVP_SYNC_ISSU-2-SESSION_NEGO

2-Critical

RSVP_SYNC ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The RSVP_SYNC ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

rsvp-sync

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

RSVP_SYNC_ISSU-2-SEND_NEGO_FAILED

2-Critical

RSVP_SYNC ISSU client failed to send negotiation message. Error: [dec] [chars]

The RSVP_SYNC ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

rsvp-sync

"show logging and show checkpoint client"

RSVP_SYNC_ISSU-2-GET_BUFFER

2-Critical

RSVP_SYNC ISSU client failed to get buffer for message. Error: [dec] [chars]

The RSVP_SYNC ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

rsvp-sync

"show logging and show checkpoint client"

RSVP_SYNC_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER

3-Error

'Message Type [dec]' is not supported by RSVP_SYNC ISSU client at peer

The RSVP_SYNC ISSU client at the peer supervisor is not compatible for this message type. The RSVP_SYNC client will be marked as incompatible with the peer.

rsvp-sync

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

RSVP_SYNC_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

RSVP_SYNC ISSU client capability exchange result incompatible.

The RSVP_SYNC ISSU client capability exchange have negotiated as incompatible with the peer.

rsvp-sync

"show issu negotiated capability <Session_ID>"

RSVP_SYNC_ISSU-3-CAP_INVALID_SIZE

3-Error

RSVP_SYNC ISSU client capability list is empty.

The RSVP_SYNC ISSU client capability exchange list size is invalid.

rsvp-sync

"show issu capability entires <Client_ID>"

RUDP-4-NOBUF

4-Warning

rudp [dec]: cannot get packet buffer for [chars].

A rudp link cannot allocate a packet buffer.

-

LOG_STD_REDUCE_ACTION

RUDP-3-INIT

3-Error

rudp [dec]: [chars][chars].

RUDP initialization operation fails.

-

LOG_STD_ACTION

RUDP-4-LINK

4-Warning

rudp [dec]: [chars][chars].

A warning is given out for a particular RUDP link.

-

LOG_STD_DBG_ACTION

SASL-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed.

sasl

LOG_STD_ACTION

SASL-2-INITFAIL

2-Critical

Initialization failed - [chars]

SASL component initialization failed.

sasl

LOG_STD_ACTION

SAT9K_FEC_CONTROL -3-LAG_CREATE_FAIL

3-Error

\n Failure in creating \port-channel [dec] with error code:[dec]

LAG CREATE failed

-

-

SAT9K_FEC_CONTROL -3-LAG_MEMBER_ADD_FAIL

3-Error

\n Failure in configuring \lag member Te 1/[dec] for port-channel [dec] with error code:[dec]

LAG MEMBER ADD failed for given port-channel

-

-

SAT9K_FEC_CONTROL -3-LAG_DELETE_FAIL

3-Error

\n Failure in deleting \port-channel [dec] with error code:[dec]

LAG DELETE failed

-

-

SAT9K_FEC_CONTROL -3-LAG_MEMBER_DELETE_FAIL

3-Error

\n Failure in deleting \lag member Te 1/[dec] from port-channel [dec] with error code:[dec]

LAG MEMBER ADD failed for given port-channel

-

-

SAT9K_FEC_CONTROL -3-INVLD_ACTION

3-Error

Invalid action issued by \host

-

-

-

SAT9K_FEC_CONTROL -3-INVLD_EVENT

3-Error

Invalid event received

-

-

-

SAT9k_NOTIF-0-FMEA_ALM

0-Emergency

[chars] has been [chars]

FMEA alarm notification

-

LOG_STD_ACTION

SAT9k_NOTIF-1-EQPT_ALM

1-Alert

[chars] has been [chars]

Equipment alarm notification

-

LOG_STD_ACTION

SAT9k_NOTIF-2-MEM_ALM

2-Critical

[chars] has been [chars]

Memory alarm notification

-

LOG_STD_ACTION

SAT9k_NOTIF-1-LINK_ALM

1-Alert

[chars] has been [chars] for port [dec]

Link Fault alarm notification

-

LOG_STD_ACTION

SAT9k_NOTIF-1-PORT_ALM

1-Alert

[chars] has been [chars] for port [dec]

Port/Pluggable alarm notification

-

LOG_STD_ACTION

SAT9k_NOTIF-2-UNKNOWN_ALM

2-Critical

[chars] has been [chars]

An Uncategorized alarm notification

-

LOG_STD_ACTION

SAT9k_NOTIF-3-PROC_CRT_FAIL

3-Error

Sat9k Alarm poller process could not be started

Due to internal system error the alarm poller process could not be created/initialized. Sat9k might not report alarms/notifications correctly

-

LOG_STD_ACTION

SAT9K_CTRL-3-SOC_ERR

3-Error

Socket [chars] failed for socket id [dec]

Error during socket operations

-

LOG_STD_ACTION

SAT9K_CTRL-3-CTRL_ERR

3-Error

Sat9k Controller Error: [chars]

Sat9k Controller Error

-

LOG_STD_ACTION

SAT9K_CTRL-3-XOS_ERR

3-Error

Sat9k XOS Error: [chars]

Sat9k Controller Error during XOS calls

-

LOG_STD_ACTION

SAT9K_CTRL-3-TOD_ERR

3-Error

Sat9k TOD Error: %lu seconds

Error in Time of Day update

-

LOG_STD_ACTION

SAT9K_CLT_CFG-3-INT_FAIL

3-Error

[chars]:[dec]: Internal Error

internal error

-

LOG_STD_NO_ACTION

SAT9K_IMG_DOWNLOADER -3-PROC_CRT_FAIL

3-Error

\nFailed to Create Image Download Process

-

-

-

SAT9K_IMG_DOWNLOADER -3-QUEUE_CRT_FAIL

3-Error

\nFailed to create watched Boolean for Image Download

watched Boolean creatation failed

-

-

SAT9K_IMG_DOWNLOADER -3-TFTP_READ_FAIL

3-Error

\n FTP download failure for [chars] with error code:[dec]

Download via TFTP failed

-

-

SAT9K_IMG_DOWNLOADER -3-FLASH_BURN_FAIL

3-Error

\nFailed to burn image [chars] into flash memory

Write to flash failed

-

-

SAT9K_IMG_DOWNLOADER -3-INVLD_ACTION

3-Error

Invalid action issued by host

-

-

-

SAT9K_IMG_DOWNLOADER -3-INVLD_EVENT

3-Error

Invalid event received

-

-

-

SAT9k_IMGR-3-BASE_MAC_GET_FAIL

3-Error

[chars]

Due to internal system error the interface manager process could not retrieve base mac address

-

LOG_STD_ACTION

SAT9k_IMGR-3-IMGR_LIST_FAIL

3-Error

[chars] [chars]

An internal system error occured during list operations for AP/ICL

-

LOG_STD_ACTION

SAT9k_IMGR-3-IMGR_LIST_CREATE_FAIL

3-Error

[chars]

An internal system error occured during list create operation for AP/ICL

-

LOG_STD_ACTION

SAT9k_IMGR-3-PROC_CRT_FAIL1

3-Error

Sat9k Interface Mgr process could not be started

Due to internal system error the interface manager process could not be created/initialized

-

LOG_STD_ACTION

SAT9k_IMGR-3-PROC_CRT_FAIL2

3-Error

Sat9k Interface Stats process could not be started

Due to internal system error the interface stats poller process could not be created/initialized. Sat9k might not report statistics correctly

-

LOG_STD_ACTION

SAT9k_IMGR-3-IMGR_INVALID_PARAM

3-Error

[chars] [dec]

An internal system error occured during an invalid parameter being passed to interface manager

-

LOG_STD_ACTION

SAT9k_IMGR-3-IMGR_NULL_PARAM

3-Error

[chars]

An internal system error occured due to a null parameter passed to interface manager

-

LOG_STD_ACTION

SAT9k_IMGR-3-IMGR_INVALID_EVENT

3-Error

\n Unknown event : Major [dec] Minor [dec]

Interface statistics poller received an invalid event

-

LOG_STD_ACTION

SAT9k_IMGR-3-IMGR_INVALID_CALL

3-Error

[chars]

Call to license processing is not supported on ASR 9000v Satellite

-

LOG_STD_ACTION

SAT9K_CROSS_LINK -3-CROSSLINK_MAP_FAIL

3-Error

\n Failure in configuring \crosslink mapping with error code:[dec]

CROSSLINK mapping for VICL/ICL failed

-

-

SAT9K_CROSS_LINK -3-INVLD_ACTION

3-Error

Invalid action issued by \host

-

-

-

SAT9K_CROSS_LINK -3-INVLD_EVENT

3-Error

Invalid event received

-

-

-

SBC_HA-3-INTERNAL

3-Error

An internal SBC HA error has been encountered[chars].

An internal error has been encountered.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-LARGE_IPS_MSG

3-Error

SBC failed to receive large sync message of size [dec].

The SBC module was unable to successfully receive a large sync message on the Standby. The Standby will be will not have an identical dynamic state as the Active.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-LARGE_IPS_MSG_FAIL

3-Error

SBC failed to send large sync message of size [dec].

The SBC module was unable to successfully send a large sync message to the Standby because this version of the Standby does not support large messages. The Standby will be will not have an identical dynamic state as the Active.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-CONFIG_SYNC

3-Error

SBC failed to cache SBC config of size [dec].

The SBC module was unable to successfully cache the SBC config on the Standby. The Standby will be unable to write SBC config to NVRAM.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-RF_REGISTRATION

3-Error

SBC RF failed to register

The SBC module was unable to successfully register with the RF infrastructure. SBC will not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-WATCH_PROGRESSION

3-Error

SBC RF failed to create progression watch points.

The SBC module was unable to successfully create the RF progression watch points. RF progression will not be suspended at bulk synchronisation time so some SBC calls may be lost if a switchover occurs immediately after the system reaches the Standby Hot redundancy state.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-NO_SYNC_PROCESS

3-Error

SBC RF failed to start the config sync process.

The SBC module was unable to successfully start the configuration sync process. The Standby will be unable to fully initialise.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-RF_TIMER_EXTENSION_EXPIRY

3-Error

SBC RF progression extension timer expired.

The SBC module's RF progression extension timer expired. RF progression will resume but if a switchover occurs immediately after the system reaches the Standby Hot redundancy state then some SBC calls may be lost.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-HOLD_PROGRESSION

3-Error

SBC RF failed to start the progression holding process.

The SBC module was unable to successfully start the RF progression holding process. RF progression will resume immediately but if a switchover occurs immediately after the system reaches the Standby Hot redundancy state then some SBC calls may be lost.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-RF_PROGRESSION

3-Error

SBC RF failed to resume RF progression at state [chars].

The SBC module was unable to successfully resume RF progression at the noted state. The Standby will be unable to fully initialise.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-RF_CONFIG_SYNC

3-Error

SBC RF will not be able to synchronise SBC configuration to the Standby. Failure cause: [chars].

The SBC module will not be able to synchronise the SBC config to the Standby. The Standby will be unable to write SBC config to NVRAM.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-IPC_RMI_INIT

3-Error

SBC IPC failed to register with RMI [chars].

The SBC IPC module was unable to successfully register with the Resource Manager. SBC may not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-IPC_INIT

3-Error

SBC IPC failed to initialise [chars].

The SBC IPC module was unable to successfully initialise. SBC may not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-IPC_SEND

3-Error

SBC IPC message send failed error [chars].

The SBC module was unable to successfully send a message to its peer. SBC will not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-ISSU_REGISTRATION

3-Error

SBC ISSU failed to register.

The SBC module was unable to successfully register with the ISSU infrastructure. SBC will not be able to operate in a stateful mode.

sbc ha

LOG_STD_ACTION

SBC_HA-3-ISSU_CLIENT_REGISTRATION

3-Error

SBC Client [dec] Registration failed [chars].

The SBC module was unable to successfully register with the ISSU infrastructure. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu clients"

SBC_HA-3-ISSU_ENTITY_REGISTRATION

3-Error

SBC Entity [dec] Registration failed [chars].

The SBC ISSU entity could not be registered. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu entities"

SBC_HA-3-ISSU_MSGTYPE_REGISTRATION

3-Error

SBC Msg Type for Entity [dec] Registration failed [chars].

The message type for SBC ISSU could not be registered. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu message types"

SBC_HA-3-ISSU_MSGGROUP_REGISTRATION

3-Error

SBC Msg Group [dec] for Entity [dec] Registration failed [chars].

The message group for SBC ISSU could not be registered. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu message groups"

SBC_HA-3-ISSU_CAPTYPE_REGISTRATION

3-Error

SBC Cap Type for Entity [dec] Registration failed [chars].

A capability type could not be registered for SBC ISSU. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu capability types"

SBC_HA-3-ISSU_CAPENTRY_REGISTRATION

3-Error

SBC Cap Entry [dec] for Entity [dec] Registration failed [chars].

A capability entry could not be registered for SBC ISSU. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu capability entries"

SBC_HA-3-ISSU_CAPGROUP_REGISTRATION

3-Error

SBC Cap Group [dec] for Entity [dec] Registration failed [chars].

A capability group could not be registered for SBC ISSU. SBC will not be able to operate in a stateful mode.

sbc-ha

"show capability groups"

SBC_HA-3-ISSU_SESSION_REGISTRATION

3-Error

SBC session for Entity [dec] Registration failed [chars].

The SBC ISSU session could not be registered. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu sessions"

SBC_HA-3-ISSU_START_NEGOTIATION

3-Error

SBC ISSU negotiation failed to start [chars].

The SBC module was unable to successfully start negotiatiation with its peer. SBC will not be able to operate in a stateful mode.

sbc-ha

"show issu fsm"

SBC_HA-4-ISSU_GET_BUFFER

4-Warning

SBC ISSU session failed to get buffer.

The SBC ISSU client failed to get a buffer. Some High-Availability SBC information may be missing from the peer.

sbc-ha

"show processes memory"

SBC_HA-3-ISSU_NEGOTIATION

3-Error

SBC ISSU negotiation failed.

The SBC module was unable to successfully negotiate with its peer. SBC will not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-ISSU_MSG_MTU

3-Error

SBC Client [dec] get msg mtu failed. Error = [dec].

The SBC ISSU client could not obtain a message of the required size.

sbc-ha

"show issu fsm"

SBC_HA-3-ISSU_TRANSFORM

3-Error

SBC ISSU [chars] transformation failed [chars].

The transformation operation for an SBC ISSU message has failed.

sbc-ha

"show issu fsm and show issu sessions"

SBC_HA-3-LARGE_IPS_UNSUPP

3-Error

The current version of the SBC Standby does not support the syncing of large SBC contexts

The current version of the SBC Standby does not support the syncing of large SBC contexts. A context that contains 24 or more media and signaling flows is a large context. It is rare to have such a large context and thus ISSU compatibility has been permitted even though this difference in support exists. Normal SBC High Availability synchronization will continue to operate successfully as long as no contexts contain more than 24 signaling or media flows. Context information beyond 24 flows will not be replicated and thus on RP switchover the Active RP will not have information about all the contexts

sbc-ha

LOG_STD_ACTION

SBC_HA-3-ILT_STUB

3-Error

SBC ILT Stub process creation failed.

The SBC module was unable to successfully create the ILT Stub process. SBC will not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-ILT_REGISTRATION

3-Error

SBC ILT registration failed.

The SBC module was unable to successfully register for communication with the peer unit. SBC will not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-ILT_PROC_CREATE

3-Error

SBC ILT process creation failed.

The SBC module was unable to successfully create an SBC process. SBC will not be able to operate in a stateful mode.

sbc-ha

LOG_STD_ACTION

SBC_HA-3-SBC_IPV6_CFG

3-Error

SBC has detected configuration/dynamic state [chars] which is

Peer SBC does not support IPv6.

sbc-ha

"Manually remove IPv6 configuration and reinitiate" " ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_DYNAMIC_CODEC_CFG

3-Error

SBC has detected Dynamic Codec configuration which is\n not supported on the peer. SBC cannot proceed as HA client.\n Remove all codec configuration to proceed with ISSU/ISSD.\n

Peer SBC does not support Dynamic Codec configuration.

sbc-ha

"Manually remove Dynamic Codec configuration and reinitiate" " ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_XML_BILLING_CFG

3-Error

SBC has detected Xml Billing configuration which is\n not supported on the peer. SBC cannot proceed as HA client.\n Remove all xml billing configuration to proceed with ISSU/ISSD.\n

Peer SBC does not support Xml Billing configuration.

sbc-ha

"Manually remove Xml Billing configuration and reinitiate" " ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_RG_NO_TRANSPORT

3-Error

SBC was unable to register a transport with the RG\n infrastructure for inter-chassis HA.\n

SBC will not be able to support inter-chassis HA.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_RG_NO_CLIENT

3-Error

SBC was unable to register the RG Client with the RG\n infrastructure for inter-chassis HA.\n

SBC will not be able to support inter-chassis HA.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_RG_NO_PROCESS

3-Error

SBC was unable to start a process used by the RG client\n

SBC will not be able to support inter-chassis HA.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_RG_NO_SOCKET

3-Error

SBC was unable to open a socket for the RG client\n

SBC will not be able to support inter-chassis HA.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_RG_SOCK_FAIL

3-Error

SBC lost connection with RG peer socket failure [chars] len=[dec]\n

SBC HA may be disabled until peer connection is established.

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_CODEC_INTERWORK_CFG

3-Error

SBC has detected codec configuration which is\n not supported on the peer. SBC cannot proceed as HA client.\n Remove all newly entered codec configuration to proceed\n with ISSU/ISSD.\n

Peer SBC does not support codec preference variant or interwork configuration.

sbc-ha

"Manually remove newly added codec configuration and" " reinitiate ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_MSMB_CFG

3-Error

SBC has detected Multi SBC Media\n Bypass configuration which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all Multi SBC Media Bypass configuration to proceed \n with ISSU/ISSD.\n

Peer SBC does not support Multi SBC Media Bypass configuration.

sbc-ha

"Manually remove Multi SBC Media Bypass configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_DBL_NA_ALERT_CFG

3-Error

SBC has detected blacklist entries configured\n which have reason na-policy-failure\n OR minor major critical alerts which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all blacklist entries with this reason or any alerts\n configuration to proceed with ISSU/ISSD.\n

Peer SBC does not support blacklist reason na-policy-failure or blacklist alerts configuration.

sbc-ha

"Manually remove blacklist reason na-policy-failure and " "minor major or critical alerts configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_B2B_RESTART

3-Error

SBC restart has taken longer than expected.\n The SBC will be restarted but may require a \n shut/no shut of the redundancy group in order to\n return to stateful HA with the active router.\n

SBC process restart timedout may require manual intervention.

sbc-ha

"Shut/No shut the standby redundancy group associated with the SBC." LOG_STD_ACTION

SBC_HA-3-SBC_HA_CALL_ONA_CFG

3-Error

SBC has detected\n first-outbound-na-table configured within a call-policy-set.\n This command is not supported on the peer. SBC cannot proceed\n as HA client. Remove all first-outbound-na-table configuration\n to proceed with ISSU/ISSD.\n

Peer SBC does not support first-outbound-na-table configuration within a call-policy-set.

sbc-ha

"Manually remove the first-outbound-na-table configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_HA_ADMIN_DOMAIN_CFG

3-Error

SBC has detected\n an admin-domain configuration. This feature is not supported \n on the peer. SBC cannot proceed as HA client. Remove all \n admin-domain submodes from the configuration to proceed with \n ISSU/ISSD.\n

Peer SBC does not support admin-domain configuration.

sbc-ha

"Manually remove the admin-domain submodes from configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_HA_CAC_AVG_PER2_CFG

3-Error

SBC has detected\n averaging-period 2 cac configuration. Averaging-period 2 is not\n supported on the peer. SBC cannot proceed as HA client. Remove the\n cac-policy-set averaging-period 2 configuration to proceed with\n ISSU/ISSD.\n

Peer SBC does not support averaging-period 2 cac configuration.

sbc-ha

"Manually remove the cac-policy-set averaging-period 2 configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_HA_CAC_AVG_PER2_RATE_CFG

3-Error

SBC has detected\n cac-policy-set rate limit configuration for averaging-period 2.\n Averaging-period 2 is not supported on the peer. SBC cannot proceed\n as HA client. Remove the cac-policy-set rate limit configuration \n for averaging-period 2 to proceed with ISSU/ISSD.\n

Peer SBC does not support cac rate limit configuration for averaging-period 2.

sbc-ha

"Manually remove the rate limit commands for averaging-period 2 found " "within the cac-policy-set entry and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_HA_PORT_TAG_CFG

3-Error

SBC has detected\n an port tag configuration. This feature is not supported \n on the peer. SBC cannot proceed as HA client. Remove all \n port tag from the configuration to proceed with \n ISSU/ISSD.\n

Peer SBC does not support port tag configuration.

sbc-ha

"Manually remove the port tag from configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_FLEX_MED_RTG_CFG

3-Error

SBC has detected\n flexible media routing configuration. This feature is not supported \n on the peer. SBC cannot proceed as HA client. Remove all \n flexible media routing config from the configuration to proceed with \n ISSU/ISSD.\n

Peer SBC does not support flexible media routing configuration.

sbc-ha

"Manually remove flexible media routing from configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_HA_CAC_PRIVACY_SERV_CFG

3-Error

SBC has detected\n cac-policy-set privacy-service configuration for a cac entry.\n This enhancement is not supported on the peer. SBC cannot proceed\n as HA client. Remove the cac-policy-set privacy-service related \n configuration to proceed with ISSU/ISSD.\n

Peer SBC does not support cac-policy-set privacy-service configuration for a cac entry.

sbc-ha

"Manually remove the privacy-service related commands configured " "within the cac-policy-set entry and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_IMP_NA_REGEX_CFG

3-Error

SBC has detected number analysis entries that match on text addresses which are not supported on the peer.\n Remove all regex number analysis entries to proceed with ISSU/D

Peer SBC does not support regex number analysis entries.

sbc-ha

"Manually remove regex number analysis entries" " and reinitiate ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_IMP_NA_EDITSRC_CFG

3-Error

SBC has detected number analysis entries that have edit-src actions which are not supported on the peer.\n Remove all edit-src actions from all number analysis entries to proceed with ISSU/D

Peer SBC does not support edit-src actions in number analysis entries.

sbc-ha

"Manually remove edit-src actions from " "all number analysis entries and reinitiate " "ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_IMP_NA_SRCANON_CFG

3-Error

SBC has detected na-src-name-anonymous number analysis tables which are not supported on the peer.\n Remove all na-src-name-anonymous number analysis tables to proceed with ISSU/D

Peer SBC does not support na-src-name-anonymous number analysis tables.

sbc-ha

"Manually remove all na-src-name-anonymous number" " analysis tables and reinitiate ISSU. " LOG_STD_ACTION

SBC_HA-3-SBC_MESSAGE_EDITING_CFG

3-Error

SBC has detected message editing configured\n which may have \sip editor_type editor\\n OR parameter-editor OR header-editor OR method-editor OR body-editor\n OR option-editor which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all message editing config to proceed with ISSU/ISSD.\n

Peer SBC does not support message editing configuration.

sbc-ha

"Manually remove message editing configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_RG_NO_VRF

3-Error

SBC VRF mismatch between active and standby please add [chars]

SBC may fail to fully support SSO

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_RG_VRF_INUSE

3-Error

VRF is used by SBC add back or remove from active please add [chars]

SBC may fail to fully support SSO

sbc-ha

LOG_NO_ACTION

SBC_HA-3-SBC_SIPS_H323_INTWK_CFG

3-Error

SBC has detected SIPS-H323 Interworking configured\n which may have trusted H323 Adjacencies or secure calls\n configured which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all SIPS-H323 Interworking config to proceed with ISSU/ISSD.\n

Peer SBC does not support SIPS-H323 Interworking configuration.

sbc-ha

"Manually remove SIPS-H323 Interworking configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_LRU_CFG

3-Error

SBC has detected LRU configured\n SBC cannot proceed now.\n Remove all LRU CONFIG to proceed with ISSU/ISSD.\n

Peer SBC does not support LRU configuration.

sbc-ha

"Manually remove LRU configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_SDP_EDITING_CFG

3-Error

SBC has detected sdp editing configured\n which may have script-set OR active-script-set\n OR \test script-set on any adjacency\ configured \n which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all sdp editing config to proceed with ISSU/ISSD.\n

Peer SBC does not support sdp editing configuration.

sbc-ha

"Manually remove sdp editing configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_CAC_ENHANCEMENT_CFG

3-Error

SBC has detected cac enhancement feature configured\n which may have branch cli \n OR cac-scope adjacency accountcli \n

Peer SBC does not support cac enhancement feature configuration.

sbc-ha

"Manually remove cac enhancement feature configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_QOS_DEMARCATION_CFG

3-Error

SBC has detected qos demarcation configured\n which may have statistics threshold \n OR g107a factor OR cal_moscqe OR g107 bpl OR g107 ie\n OR qos trap configured which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all qos demarcation config to proceed with ISSU/ISSD.\n

Peer SBC does not support qos demarcation configuration.

sbc-ha

"Manually remove qos demarcation configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_VIA_PASSTHROUGH_CFG

3-Error

SBC has detected Via Passthrough configured\n SBC cannot proceed now.\n Remove all Via Passthrough CONFIG to proceed with ISSU/ISSD.\n

Peer SBC does not support Via Passthrough configuration.

sbc-ha

"Manually remove Via Passthrough configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_MEDIA_BYPASS_NATTAGGEN_CFG

3-Error

SBC has detected media bypass auto-nat-tag-gen configured\n SBC cannot proceed now.\n Remove all media bypass auto-nat-tag-gen config to proceed with ISSU/ISSD.\n

Peer SBC does not support media bypass auto-nat-tag-gen configuration.

sbc-ha

"Manually remove media bypass auto-nat-tag-gen configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_MEDIA_ADDRESS_PRESERVE_INIT_NEGO_CFG

3-Error

SBC has detected media address preserve init-negotiation configured\n SBC cannot proceed now.\n Remove all media address preserve init-negotiation config to proceed with ISSU/ISSD.\n

Peer SBC does not support media address preserve init-negotiation configuration.

sbc-ha

"Manually remove media address preserve init-negotiation configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_SUBSCRIBER_TCP_CFG

3-Error

SBC has detected subscriber tcp configured\n which may have subscriber tcp incoming-only configured\n which is not supported on the peer.\n SBC cannot proceed as HA client.\n Remove all subscriber tcp config to proceed with ISSU/ISSD.\n

Peer SBC does not support susbscriber tcp configuration.

sbc-ha

"Manually remove subscriber tcp configuration " "and reinitiate ISSU." LOG_STD_ACTION

SBC_HA-3-SBC_IMS_RF_CFG

3-Error

SBC has detected ims rf configured. SBC cannot proceed now.\n Remove all ims rf config to proceed with ISSU/ISSD.\n

Peer SBC does not support ims rf configuration.

sbc-ha

"Manually remove ims rf configuration and reinitiate ISSU." LOG_STD_ACTION

SMC-2-BAD_ID_HW

2-Critical

Failed Identification Test in [chars] [[dec]/[dec]]\n\n\ The module in [chars] in this router may not be a genuine \n\ Cisco product. Cisco warranties and support programs only\n\ apply to genuine Cisco products. If Cisco determines that\n\ your insertion of non-Cisco memory WIC cards AIM cards \n\ Network Modules SPA cards GBICs or other modules into a \n\ Cisco product is the cause of a support issue Cisco may \n\ deny support under your warranty or under a Cisco support \n\ program such as SmartNet.\n\n

Hardware in the specified location could not be identified as \n\ a genuine Cisco product

c2800

"Contact TAC" LOG_STD_RECUR_ACTION

SMC-2-PROTO_HW

2-Critical

Module [chars] is a registered proto-type for Cisco Lab

Hardware in the specified location is a proto-type module that came\n\ from a Cisco Lab

c2800

"Contact TAC" LOG_STD_RECUR_ACTION

SMC-2-FAILED_ID_HW

2-Critical

Failed Identification Test in [chars] [[dec]/[dec]]\n

There was a problem while identifying Hardware in the specified\n\ location.

c2800

"Contact TAC" LOG_STD_RECUR_ACTION

HW-2-OBSOLETE_HW_VER

2-Critical

Module Version in [chars] is obsolete\n\ *********************************************************************\n\ * IMPORTANT !!! *\n\ * The module in [chars] is obsolete and must be returned *\n\ * via RMA to Cisco Manufacturing. If it is a lab unit * \n\ * it must be returned to Proto Services for upgrade. *\n\ *********************************************************************\n

The Smart Cookie is obsolete and need to be replaced ASAP.

c2800

"Contact TAC" LOG_STD_RECUR_ACTION

BINDLABEL-3-BINDLABEL_ERR

3-Error

Bind label error [chars]

An error happen when create/lookup bind label.

BINDLABEL_COMPONENT

LOG_STD_ACTION

SDVXLAN-3-VXLAN_TUN_FULL

3-Error

Auto-tunnel ID is running out now

All the vxlan auto-tunnel ID through the tunnel range was used no more id available

SDVXLAN_COMPONENT

"If the auto-tunnel ID is running out " "will need to config the auto-tunnel range to expand it"

IP_SOURCE_GUARD-4-DENY_INVALID_PACKET

4-Warning

Detected and dropped illegal traffic on port [chars] and vlan [dec] the non-cumulative packet dropped count is %ld.

IP Source Guard only permits traffic with the correct source IP to MAC\n\ binding on the port or VLAN. There may be a malicious host trying to\n\ carry out a denial of service attack using another host's source address.\n\ The illegal traffic is dropped by the IP Source Guard feature.

ipsg

"Identify the source of the illegal traffic " "and stop it."

IP_PORT_SECURITY-4-DENY_INVALID_PACKET

4-Warning

Detected and dropped illegal traffic on port [chars] and vlan [dec] the non-cumulative packet dropped count is %ld.

IP Port Security only permits traffic with the correct source IP to MAC\n\ binding on the port or VLAN. There may be a malicious host trying to\n\ carry out a denial of service attack using another host's source address.\n\ The illegal traffic is dropped by the IP Port Security feature.

ipsg

"Identify the source of the illegal traffic " "and stop it."

DRP-3-SUBNETTED

3-Error

unable to determine metric for [inet] [inet] subnetted

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DRP-7-NOROUTE

7-Debug

no route for destination [inet]

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DRP-3-NOWRITE

3-Error

unable to send response to [inet]:[dec]

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DRP-3-MULTICOMMAND

3-Error

multiple DRP commands encountered

Multiple DRP commands were found in a single DRP packet.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DRP-3-NOSOCKET

3-Error

Unable to open socket

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

DNSSERVER-3-BADQUERY

3-Error

Bad DNS query from [inet]

A client sent a DNS query to the server which has been found to be incorrectly formatted.

-

"Check the DNS server and the network attached to it."

DNSSERVER-3-TOOSHORT

3-Error

DNS query from [inet] too short

A client sent a short DNS query packet to the server

-

"Check the client and the network attached to it."

DNSSERVER-3-UDPDNSOVERLOAD

3-Error

Low available memory: dropping <id# [dec]> from <cli [inet]>.

There is not enough free memory to handle DNS queries.

-

"DNS server is automatically discarding DNS request traffic."

DNSSERVER-3-TCPDNSOVERLOAD

3-Error

Low available memory: dropping TCP request from <cli [inet]>.

There is not enough free memory to handle DNS queries.

-

"DNS server is automatically discarding DNS request traffic."

DNSSERVER-3-NOINIT

3-Error

Can't initialize DNS server

Internal problems with initializing ports for the DNS server

-

"Make sure the DNS server port is available on the local machine."

DIRECTOR-3-BADCOMPL

3-Error

plug-in returned orphan status

A software or hardware error occurred.

dist-director

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIRECTOR-3-NOSOCKET

3-Error

[chars] unable to create socket

A software or hardware error occurred.

dist-director

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIRECTOR-3-NOWRITE

3-Error

[chars] unable to write to socket

A software or hardware error occurred.

dist-director

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DIRECTOR-3-NOPROC

3-Error

unable to create [chars] process

Most likely a resource problem within the system.

dist-director

"Reboot the system as soon as possible. If the problem continues\n\ to occur report it to your technical support representative."

DIRECTOR-3-NOPORT

3-Error

[chars] port in use

The IP address requested has been found to be already in use on\n\ some interface connected to the system or within the system itself.

dist-director

"Either select another IP address for use or locate the system making\n\ use of this address and reconfigure it to use another."

DIRECTOR-3-NOALIAS

3-Error

[chars] can not create ip alias

Most likely a resource problem within the system.

dist-director

"Reboot the system as soon as possible. If the problem continues\n\ to occur report it to your technical support representative."

DIRECTOR-3-DRPDOWN

3-Error

DRP [inet] was down %TE ago in the last [dec] minute period ! There may be problems related to this DRP agent.

The remote DRP agent has not responded within the time period reported

-

"Make sure the remote DRP agent is running and that it is accessible\n\ from the system reporting the problem."

DIRECTOR-3-HTTPOVERLOAD

3-Error

Excessive HTTP request overloading: dropping HTTP req from <cli [inet]>.

HTTP requests are overloading the web redirector

dist-director

"Web redirector is automatically discarding HTTP request traffic."

DIRECTOR-3-URLELSEWHERE

3-Error

URL is elsewhere '[chars]' Code [dec] - [chars]

The HTTP return code indicates the page is not actually on this server

dist-director

"Check the URL configured. Check the configured HTTP server."

DIRECTOR-3-URLSVRERR

3-Error

Server error '[chars]' Code [dec] - [chars]

The HTTP return code indicates a server failure error

dist-director

"Check the URL configured. Check the configured HTTP server."

DIRECTOR-3-NOTCONF

3-Error

Metric [chars] referenced but not found

-

dist-director

-

DIRECTOR-5-SVRUPDOWN

5-Notice

server [inet] on port [dec] has gone [chars]

The remote server has gone up or down

dist-director

"None."

DIRECTOR-6-SVRSELECT

6-Information

select [inet] host [chars] cli [inet] type [chars] id# [dec] [chars]

Report server selection process.

dist-director

"None."

DIRECTOR-6-SVRNSELCT

6-Information

no answer for host [chars] cli [inet] type [chars] id# [dec] [chars]

No server found.

dist-director

"None."

DIRECTOR-6-DNSQUERY

6-Information

query type [chars] host [chars] cli [inet] id# [dec]

DNS query logging.

dist-director

"None."

DIRECTOR-6-DNSRESPN

6-Information

answer type [chars] host [chars] cli [inet] id# [dec] svr [inet]

DNS reply logging with server found.

dist-director

"None."

DIRECTOR-6-DNSNORSP

6-Information

answer type [chars] host [chars] cli [inet] id# [dec] none

DNS reply logging: no server found.

dist-director

"None."

DHCP_SNOOPING_ISSU-2-INIT

2-Critical

DHCP Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars]

The DHCP Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

dhcp-snooping

LOG_STD_ACTION

DHCP_SNOOPING_ISSU-3-TRANSFORM_FAIL

3-Error

DHCP Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The DHCP Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the DHCP Snooping state between the active device and the standby device is not identical.

dhcp-snooping

"show issu session <client_id> and " "show issu negotiated version <session_id>"

DHCP_SNOOPING_ISSU-3-MSG_NOT_OK

3-Error

DHCP Snooping ISSU client 'Message Type [dec]' is not compatible

The DHCP Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed.

dhcp-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

DHCP_SNOOPING_ISSU-3-MSG_SIZE

3-Error

DHCP Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The DHCP Snooping ISSU client failed to calculate the MTU for the specified message. The DHCP Snooping ISSU client is not able to send the message to the standby device.

dhcp-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

DHCP_SNOOPING_ISSU-3-INVALID_SESSION

3-Error

DHCP Snooping ISSU client does not have a valid registered session.

The DHCP Snooping ISSU client does not have a valid registered session.

dhcp-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

DHCP_SNOOPING_ISSU-2-SESSION_REGISTRY

2-Critical

DHCP Snooping ISSU client failed to register session information. Error: [dec] [chars]

The DHCP Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

dhcp-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

DHCP_SNOOPING_ISSU-3-SESSION_UNREGISTRY

3-Error

DHCP Snooping ISSU client failed to unregister session information. Error: [dec] [chars]

The DHCP Snooping ISSU client failed to unregister session information.

dhcp-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

DHCP_SNOOPING_ISSU-2-SESSION_NEGO

2-Critical

DHCP Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The DHCP Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

dhcp-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

DHCP_SNOOPING_ISSU-2-SEND_NEGO_FAILED

2-Critical

DHCP Snooping ISSU client failed to send negotiation message. Error: [dec] [chars]

The DHCP Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

dhcp-snooping

"show logging and show checkpoint client"

DHCP_SNOOPING_ISSU-2-GET_BUFFER

2-Critical

DHCP Snooping ISSU client failed to get buffer for message. Error: [dec] [chars]

The DHCP Snooping ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

dhcp-snooping

"show logging and show checkpoint client"

DHCP_SNOOPING-3-DHCP_SNOOPING_INTERNAL_ERROR

3-Error

DHCP Snooping internal error [chars]

A software sanity check failed in the DHCP Snooping process.

dhcp-snooping

LOG_STD_SH_TECH_ACTION

DHCP_SNOOPING-4-DHCP_SNOOPING_PVLAN_WARNING

4-Warning

DHCP Snooping configuration may not take effect on secondary vlan [dec]. [chars]

If private vlan feature is enabled DHCP Snooping configuration on primary vlan will automatically propagate to all secondary vlans.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-IP_SOURCE_BINDING_PVLAN_WARNING

4-Warning

IP source filter may not take effect on secondary vlan [dec] where IP source binding is configured. [chars]

If private vlan feature is enabled IP source filter on primary vlan will automatically propagate to all secondary vlans.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-IP_SOURCE_BINDING_NON_EXISTING_VLAN_WARNING

4-Warning

IP source binding is configured on non existing vlan [dec].

IP source binding is configured on a non existing vlan.

dhcp-snooping

"Please make sure that the L2 VLAN is configured before configuring a " "DHCP Snooping Binding. If you see this message even though L2 VLAN is " "configured in the system please contact Cisco Technical Assistance " "Center."

DHCP_SNOOPING-4-DHCP_SNOOPING_ERRDISABLE_WARNING

4-Warning

DHCP Snooping received [dec] DHCP packets on interface [chars]

DHCP Snooping detected a DHCP packet rate limit violation on a particular interface. The interface will be error disabled.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-AGENT_OPERATION_FAILED

4-Warning

DHCP snooping binding transfer failed. [chars]

This message provides the reason of failure when a database transfer\n\ has failed.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-STANDBY_AGENT_OPERATION_FAILED

4-Warning

DHCP snooping binding transfer failed on the Standby Supervisor. [chars]

This message provides the reason of failure when a database transfer\n\ has failed on the Standby Supervisor.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-AGENT_OPERATION_FAILED_N

4-Warning

DHCP snooping binding transfer failed[dec]. [chars]

This message provides the reason of failure when a database transfer\n\ has failed. This log message is rate limited.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-6-AGENT_OPERATION_SUCCEEDED

6-Information

DHCP snooping database [chars] succeeded.

This message indicates that the given binding transfer has succeeded.\n\ This message is logged only once after some failure to indicate that the\n\ switch has recovered from failures.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-6-BINDING_COLLISION

6-Information

Binding collision. [dec] bindings ignored

This message indicates that the given number of bindings from the \n\ database file have been ignored when the file is read. The bindings\n\ are ignored because the system has a binding for the given mac address\n\ and vlan combination by the time the switch read the ignored binding\n\ from the file.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-6-LEASE_EXPIRED

6-Information

Lease Expired. [dec] bindings ignored.

This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because their lease has expired.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-6-INTERFACE_NOT_VALID

6-Information

Interface not valid. [dec] bindings ignored.

This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because the interface indicated by the ignored binding\n\ either does not exist in the system or it's a router or dhcp \n\ snooping trusted port.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-6-VLAN_NOT_SUPPORTED

6-Information

Vlan not supported. [dec] bindings ignored.

This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because the vlan indicated by the ignored binding\n\ no longer exists in the system.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-DHCP_SNOOPING_DATABASE_FLASH_WARNING

4-Warning

Saving DHCP snooping bindings to [chars] can fill up your device causing the writes of bindings to device to fail.

Saving DHCP Snooping bindings to a flash file system such as\n\ bootflash or slot0 could cause the flash to fill up. Possible\n\ consequences include the long delay to regain console write\n\ failures for database config regular squeeze requirements and\n\ reduced life of flash due to regular squeeze operations etc.

dhcp-snooping

"Alternate destination locations for database agent " "include tftp ftp rcp etc. Please see the help " "at command line for a complete list of options."

DHCP_SNOOPING-6-PARSE_FAILURE

6-Information

Parsing failed for [dec] bindings.

This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because of parsing failures.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-SSO_SYNC_ACK_ERROR

4-Warning

Error is encountered in processing acknowledgement for DHCP snooping binding sync [chars]. ack message txn id: 0x[hec]

This message indicates that there is an error in handling of the\n\ dhcp snooping binding sync acknowledgement. In most of these cases\n\ the ack message is ignored.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-QUEUE_FULL

4-Warning

Fail to enqueue DHCP packet into processing queue: [chars] the queue is most likely full and packet will be dropped.

If the DHCP snooping bindings are loaded by the DHCP snooping database agent and NTP is not sync then the calculated lease duration for the bindings will be incorrect.

firmware

"Synchronize NTP on the switch to provide an accurate " "time and date for the system clock. Then disable and " "re-enable DHCP snooping to clear the bindings database."

DHCP_SNOOPING-4-DHCP_SNOOPING_RATE_LIMIT_EXCEEDED

4-Warning

The interface [chars] is receiving more than the threshold set

This message indicates that a DHCP packets are coming into cpu\n\ at a much higher rate than the specified threshold.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-5-DHCP_SNOOPING_UNTRUSTED_PORT

5-Notice

[chars] drop message on untrusted port message type: [chars] MAC sa: [enet]

DHCP Snooping discovers certain types of DHCP message not allowed on\n\ the untrusted interface some host maybe trying to act as a DHCP server.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-5-DHCP_SNOOPING_NONZERO_GIADDR

5-Notice

[chars] drop message with non-zero giaddr or option82 value on untrusted port message type: [chars] MAC sa: [enet]

DHCP Snooping discovers DHCP packet with certain option value not\n\ allowed on the untrusted port some host maybe trying to act as a DHCP\n\ relay or server.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-5-DHCP_SNOOPING_FAKE_INTERFACE

5-Notice

[chars] drop message with mismatched source interface the binding is not updated message type: [chars] MAC sa: [enet]

DHCP Snooping discovers some host is trying to act as another host\n\ on the network and trying to carry out a DOS attack on that host.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL

5-Notice

[chars] drop message because the chaddr doesn't match source mac message type: [chars] chaddr: [enet] MAC sa: [enet]

DHCP Snooping enables match-source-mac validation and the check is\n\ failed. There maybe a malicious host trying to carry out a DOS\n\ attack on the DHCP server.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-OPTION82_INSERTION_FAIL

4-Warning

The interface [chars] is not able to insert opt82 into the packet\n\ because of insufficient space in the packet

This message indicates that a DHCP packet was not inserted with\n\ opt82 data due to insufficient space in the packet.

dhcp-snooping

LOG_STD_NO_ACTION

DHCP_SNOOPING-4-INVALID_RELEASE_OR_DECLINE_PKT

4-Warning

The interface [chars] has received a DHCP Release/Decline packet \n\ with no existing binding entry for it

This message indicates that a DHCP Release/Decline packet was received \n\ with no corresponding binding entry.

dhcp-snooping

LOG_STD_NO_ACTION

SERVICE_GROUP-3-SG_CREATION_ERROR

3-Error

An error is detected when creating Service Group [dec] [chars]

An error was detected when creating a service group. The failure most likely occurred because of a software error.

ether-infra

"Please copy the error message exactly as it appears and report it " "to your technical support representative."

SERVICE_GROUP-3-SG_DELETION_ERROR

3-Error

An error is detected when deleting Service Group [dec] [chars]

An error was detected when deleting a service group. The failure most likely occurred because of the group is not configured or a software error.

ether-infra

"If the group is configured please copy the error message exactly " "as it appears and report it to your technical support " "representative."

SERVICE_GROUP-3-SG_INTERNAL_ERROR

3-Error

Service Group detected an internal error [chars] [dec]

An internal error was detected by the service group software.

ether-infra

"Please copy the error message exactly as it appears and report it " "to your technical support representative."

SERVICE_GROUP-3-SG_IPC_TRANSMIT_FAILED

3-Error

Service Group IPC message transmission failure [chars]

An error was detected when transmitting an IPC message between route processor and linecard. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred.

ether-infra

"This could be a transient error. If this error persists " "copy the error message exactly as it appears and report it " "to your technical support representative."

ACCESS_SESSION-3-TRACE_INIT_FAIL

3-Error

Initialization failed with code: [dec]

Failed to initialize access-session trace.

dot1x-ios

LOG_STD_NO_ACTION

ACCESS_SESSION-3-TRACE_REG_FAIL

3-Error

Component [chars] registration failed. Error code: [dec]

Component failed to register with access-session trace

dot1x-ios

LOG_STD_NO_ACTION

SYS-4-GD_DATAUNRELIABLE

4-Warning

Update to memory leak detector on free of 0x[hec] failed CLI output is unreliable\n

managed chunk malloc to store the range that is freed while memory leak detector is in progress failed. Hence memory leak detector will not be updated of this free and this can be reported as leak which is false.

mem

"Ignore the output of \"show memory debug leaks..\" if system is in low " "memory condition else perform a bug toolkit search on the web for " "existing bugs related to this error message if none found contact TAC " "for this problem providing \"show version\" and " "\"show memory statistics\" output."

SYS-3-GD_STACKERR

3-Error

Unknown stack. Process: [chars]\n

An internal error occurred when running the memory leak detector

mem

"Copy the error message exactly as it appears on the console or in the" " system log and look up the message in the Bug Toolkit at:" " http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you are" " unable to resolve the issue using Bug Toolkit please issue a" " \"show tech\" and contact your technical support representative" " with the gathered information."

SYS-4-FREEMEMLOW

4-Warning

Free Memory has dropped below low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-5-FREEMEMRECOVER

5-Notice

Free Memory has recovered above low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the free memory in that pool is now above the configured low-memory limit.

-

"No action is required"

SYS-2-MALLOCFAIL

2-Critical

Memory allocation of [dec] bytes failed from [hex] alignment [dec] \n Pool: [chars] Free: [dec] Cause: [chars] \nAlternate Pool: [chars] Free: [dec] Cause: [chars] \n

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error may have exhausted or fragmented the router's memory.

mem-suspect

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representativeand provide the representative with the gathered information. " "Otherwise you may need to add more memory or reduce the number of " "features you are trying to support."

SYS-2-MUTEXLOCKFAIL

2-Critical

pthread_mutex_lock failed for [chars]

The thread failed in pthread_mutex_lock while trying to acquire a mutex.

mem-suspect

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-NOMEMORY

2-Critical

No memory available for [chars] [dec]

An operation could not be accomplished because of a low-memory condition. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

mem-suspect

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a configuration that has more memory."

SYS-3-CRITMEM

3-Error

[chars]

An attempt to allow or disallow a process from using memory that has been reserved for critical purposes has failed. The location of the failure is specified in the error message. This condition could possibly be caused by a software error.

mem-suspect

"Copy the error message and the traceback messages exactly as they appear " "on the colsole or in the system log contact your technical support " "representative and provide the representative with the gathered " "information."

SYS-2-GETBUFFFAIL

2-Critical

[chars] buffer allocation [dec] bytes failed from [hex]

-

-

-

SYS-6-NOBRIDGE

6-Information

Bridging software not present

Your system is not configured to be a bridge.

none

"Configure the bridging software."

SYS-3-SOCKUNKN

3-Error

Unknown socket protocol [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-HARIKARI

3-Error

Process [chars] top-level routine exited

An internal software error occurred

Determine the component from the process name displayed in the error message.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPID

2-Critical

Bad pid [dec] for tty [t-line]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-MGDTMRRUN

3-Error

TTY[t-line]: Managed Timers [chars] still running

One or more managed timers for a TTY that is deleted are still running.

-

LOG_STD_ACTION

SYS-0-USERLOG_EMERG

0-Emergency

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-1-USERLOG_ALERT

1-Alert

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-2-USERLOG_CRIT

2-Critical

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only. "

SYS-3-USERLOG_ERR

3-Error

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-4-USERLOG_WARNING

4-Warning

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-5-USERLOG_NOTICE

5-Notice

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-6-USERLOG_INFO

6-Information

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-7-USERLOG_DEBUG

7-Debug

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-3-MSGLOST

3-Error

[dec] messages lost because of queue overflow

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-REGEXP

4-Warning

[chars].

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-5-RESTART

5-Notice

System restarted --\n[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SCHEDULED_RELOAD

5-Notice

Reload requested for [chars]

A scheduled reload has been requested for the router.

none

"No action is required."

SYS-5-SCHEDULED_RELOAD_CANCELLED

5-Notice

Scheduled reload cancelled at [chars]

A scheduled reload that was requested for the router has been cancelled.

none

"No action is required."

SYS-5-RELOAD

5-Notice

Reload requested[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SWITCHOVER

5-Notice

Switchover requested[chars]

A switchover was requested.

none

"This is a notification message only. No action is required."

SYS-4-RELOAD_ATTEMPT

4-Warning

Attempt via SNMP failed system shutdown not configured

SNMP cannot be used to reload the router unless this functionality has been previously configured. This message reports that an attempt to reload the router failed because SNMP reloads are not currently configured on the router.

none

"This is a notification message only. No action is required."

SYS-3-CFG_AT_RELOAD

3-Error

System reloading unable to complete startup configuration update

Startup configuration updation is already in progress and reload has been called either from interrupt level or with all interrupts disabled. Reload can not suspend to let startup configuration updation get completed. Startup configuration may get corrupted.

none

"This is a notification message only. No action is required."

SYS-4-DUAL_MESSAGE

4-Warning

SNMP system message request [dec] denied because of pending job

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-5-CONFIG

5-Notice

Configured from [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_I

5-Notice

Configured from [chars] by [chars]

The write of the system running configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_RESOLVE_FAILURE

4-Warning

System config parse from [chars] failed

The configuration file from the URL specified in the error message could not be read.

-

"Enter the <CmdBold>no service config<NoCmdBold> " "command to disable autoloading of configuration files " "OR investigate why the tftp load is failing."

SYS-5-CONFIG_NV

5-Notice

Nonvolatile storage configured from [chars]

The configuration was written successfully.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_NV_I

5-Notice

Nonvolatile storage configured from [chars] by [chars]

The write of the nonvolatile configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-CONFIG_NV_DATA

3-Error

Variable [chars] not set properly in the routine [chars].

The write of the nonvolatile configuration failed because an internal variable was not set properly.

-

"If this messages occurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_NEWER

4-Warning

Configuration from version [dec].[dec] may not be correctly understood

The software detected that the configuration saved in memory was written by a newer version of software. There might be commands saved in memory that are not implemented by the older software version.

none

"Examine all the messages printed while the router was " "booting. For each message about an unknown command determine " "whether that feature is required. If so upgrade to a " "newer version of software that supports that feature."

SYS-4-CONFIG_NOLOCK

4-Warning

The configuration could not be locked

A software error occurred.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SYS-3-CONFIG_NO_PRIVATE

3-Error

No space remaining to save private config

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-CONFIG_NV_OVERRUN

4-Warning

Non config data present at the end of nvram is corrupted

The software detected that the configuration saved into nvram has overlaid a part of the nvram occupied by non config data files.Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_TRUNCATE

4-Warning

Truncated configuration to %ld bytes from %ld bytes

The software detected that the configuration saved into nvram has been truncated. There was not enough space to save the compressed configuration.

-

"Save the configuration to flash if the platform supports " " \"boot config\" command."

SYS-4-CONFIG_NV_NEED_OVERRUN

4-Warning

Non config data present at the end of nvram needs to be overwritten to fit the configuration into nvram

The software detected that the non config data files occupying the end of nvram need to be overwritten to fit the configuration. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_NEED_TRUNCATE

4-Warning

Configuration needs to be truncated to fit into nvram

The software detected that the configuration is to be truncated to fit in the nvram. There was not enough space to save the compressed configuration

-

"Save the configuration to flash if the platform supports " "\"boot config nvbypass\" command."

SYS-4-NV_BLOCK_INITFAIL

4-Warning

Unable to initialize the geometry of nvram

The software detected that it failed to initialize the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload. This may happen when the entire nvram is packed with the configuration and the newer version of software which supports this feature could not find the minimum room in the nvram to initialize block file system.

-

"Reduce the configurations in the nvram atleast by 2K"

SYS-7-NV_BLOCK_INIT

7-Debug

Initialized the geometry of nvram

Initialized the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

""

SYS-4-NV_CHKSUM

4-Warning

An nvram checksum is already in progress

An interrupt service routine attempted to perform a checksum on the nvram contents and found the resource in use.

nvram

-

SYS-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMINIT

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be initialized. reasons are not clear.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent data some corruption.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CONFIG_DOWNFAIL

2-Critical

Generated configuration not backward compatible

The router has been configured to generate nonvolatile memory using the commands of an older software version. The current configuration of the router contains a command that cannot be saved using only the older command set.

none

"Allow the router to save the configuration using the command set of " "the current software version or remove the commands that cannot be " "saved using the older command set."

SYS-5-OUTSETUP

5-Notice

Configuration file [chars] accepted aborting setup

A configuration was accepted over the network so the setup session will be aborted.

none

"This is a notification message only. No action is required."

SYS-3-BADLINKTYPE

3-Error

* Unexpected linktype [dec]

* A software error occurred.

udp

* "Copy the error message exactly as it appears and report it to your " * "technical support representative."

SYS-2-SIGNUM

2-Critical

Process aborted on invalid signal signum = [dec].

An attempt was made to send an invalid signal to another process.

-

"If this message occurs more than once report this message " "to your technical support representative."

SYS-3-CPUHOG

3-Error

Task is running for [dec]msecs more than [dec]msecs [dec]/[dec]

The indicated process ran too long without relinquishing the processor. Each process should run for a small amount of time and then relinquish the CPU so that other processes can run. This problem can be caused by many things like traffic or system load hardware or operational configuration a configuration change initialization of many interfaces cards or ports for example a high momentary error rate a sustained abnormal

If this error occurs in conjunction with a TIMERHOG message \n\ report the two errors together and use the component obtained \n\ for the TIMERHOG message.

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representative and provide the representative with the gathered information."

SYS-2-WATCHDOG

2-Critical

Process aborted on watchdog timeout process = [chars].[chars]

The indicated process ran for too long without relinquishing control. The system killed it as a runaway process.

-

-

SYS-3-TIMERHOG

3-Error

Timer callback ran long PC = [hec].

The indicated callback routine ran for too long without relinquishing the processor.

Determine the component from the callback routine address displayed in\n\ the error message. Use Topic to search for a similar DDTS. If you \n\ find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-6-STACKLOW

6-Information

Stack for [chars] [chars] running low [dec]/[dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-GREEDY_REGEXP

4-Warning

[chars] while processing the input regular expression. Aborting processing use alternate regular expression. Input regular expression: \[chars]\

Regular expression processing limitation: Certain regular expressions require huge stack space for processing or can lead to processing timeouts. We abort processing such regular expressions and print this message to avoid stack overflow/unexpected reload.

os

"The regular expression specified leads to stack overflow/processing " "timeout of the indicated process. Recommended to use a different " "regular expression."

SYS-1-CPURISINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr: [dec]%%/[dec]%%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped.

-

"Enter the <CmdBold>show processes CPU<NoCmdBold>" " command to determine the CPU hogging process" " that is causing this condition and if possible" " disable the activity that is causing the" " CPU hog condition so that CPU" " utilization is reduced."

SYS-1-CPUFALLINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr [dec]%%/[dec]%%.

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required."

SYS-2-INPUTQ

2-Critical

INPUTQ set but no IDB ptr=[hec]

This message is issued when an attempt is made to alter the input queue count for a packet that should not be counted.

-

-

SYS-6-BADSHAREINFO

6-Information

[chars] packet [hec] has a zero reference count freeing pid = [hec] \n\ freeing pc = [hec] [chars].

Provides additional information about original freer of packet.

-

-

SYS-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[hec]

A reference count is used to track the usage of many data structures. A function increments the count when it begins to use a structure and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be negative which means that the data structure will not be freed until the system is reloaded.

-

-

SYS-2-CFORKLEV

2-Critical

Process creation of [chars] failed at level [dec].

An internal software error occurred.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKMEM

2-Critical

Process creation of [chars] failed no memory.

Insufficient memory was available to create a process either while trying to support additional features or due to a memory leak.

mem-suspect

"A memory leak may be the cause if the system has been running for a " "while without changing its configuration. If you suspect a leak then " "copy this message exactly as it appears and report it to your technical " "support representative. Otherwise ensure that more memory is available " "to support the additional features."

SYS-2-CFORKBADFUNCT

2-Critical

Can't create process with start address = [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPROCESS

3-Error

Bad process ID [dec] when [chars] process table

An internal software error occurred.

os-scheduler

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INSCHED

2-Critical

[chars] within scheduler

-

Determine the component from the stack trace displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem.

-

SYS-2-NOTIOSTASK

2-Critical

[chars] from outside IOS task context

An IOS reschedule request was made from code that is not running in the context of an IOS task -- from an interrupt handler the scheduler itself or a service pthread within the IOS process.

Determine the component from the stack trace displayed in the\n\ error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INTSCHED

2-Critical

'[chars]' at level [dec]

The scheduler was entered from an interrupt service routine ISR.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

-

SYS-3-PROCSEMFAIL

3-Error

Process semaphore creation for preemptive processes failed.

Creation of process function semaphore to protect the critical section of process create routine failed. The semaphore creation can fail if there isnt enough chunk memory to create the event structure.

os

-

SYS-2-NOBLOCK

2-Critical

[chars] with blocking disabled.

A process aattempted to relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

-

SYS-2-BLOCKHUNG

2-Critical

Task hung with blocking disabled value = 0x[hec].

The indicated process has exceeded the time limit for which it may relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

"This message may be a result of high loads. If it recurs " "copy the text exactly as it appears and report it along " "with the associated stack trace to your technical support " "representative."

SYS-2-NOTDEAD

2-Critical

Killing process [chars] pid [dec] again

An internal software error occurred.

os-scheduler

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOPROCESS

2-Critical

No such process [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-IMMORTAL

2-Critical

Attempt to shut down management process [dec] [chars].

An attempt was made to shut down the specified management process. Management processes must not be shut down as long as the\n\ router remains up.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the process_kill.

-

SYS-2-SIGPENDING

2-Critical

Multiple Signals are sent to a process [dec]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADSTACK

2-Critical

Process [chars] has trashed stack old size [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-6-MTRACE

6-Information

[chars]: addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC

This is an auxiliary message to several memory-related messages. It provides the address of the memory block and the calling program counter for the last eight blocks allocated and for the last eight blocks freed.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of a previously printed error message."

SYS-6-BLKINFO

6-Information

[chars]blk [hec] words [dec] alloc [hec] [chars] dealloc [hec] rfcnt [hec]

This is an auxiliary message to several memory-related messages. It provides a formatted display of some of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-MEMDUMP

6-Information

[hex]: [hex] [hex] [hex] [hex]

This is an auxiliary message to several memory-related messages. It provides a raw display of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-PROCINFO

6-Information

Process [chars] just finished executing

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

-

"Copy this messages exactly as it appears and report it along with " "the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your " "technical support representative."

SYS-6-TESTINFO

6-Information

Scheduler test [hex] for [chars] just executed

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

Determine the component from the address of the scheduler test routine\n\ displayed in the error message.\n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy this message exactly as it appears and report it along with the " "SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical " "support representative."

SYS-3-BADBLOCK

3-Error

Bad block pointer [hec]

A block of memory at the indicated location is corrupt. An internal check of memory block pointers indicates an inconsistency.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to auotmatically reload then the router will " "need to reloaded manually."

SYS-3-BADMAGIC

3-Error

Corrupt block at [hec] magic %08x

The free memory pool is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADREFCOUNT

3-Error

Bad reference count at [hec] refcount [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-3-OVERRUN

3-Error

Block overrun at [hec] red zone %08x

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-FREEBAD

2-Critical

Attempted to free memory at [hec] not part of buffer pool

An attempt was made to free memory but the request could not be completed due to an invalid memory data structure

-

-

SYS-2-FREEFREE

2-Critical

Attempted to free unassigned memory at %lx alloc %lx dealloc %lx

An attempt was made to free memory at the indicated location. The memory could not be freed because it was not allocated.

-

-

SYS-3-INVMEMINT

3-Error

Invalid memory action [chars] at interrupt level

This message indicates that a memory allocation or deallocation was attempted from an interrupt handler.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-INVMEMPID

3-Error

Invalid pid [dec] in block: [hec]

There has been attempt to allocate memory on behalf of an invalid process.

mem

-

SYS-3-MEMSEMFAIL

3-Error

Mempool semaphore creation failed for [chars]

This message indicates that the semaphore creation for the specified mempool failed.

-

-

SYS-3-INUSEFREE

3-Error

Block [hec] on free list [dec] in use

A memory management function attempted to allocate the indicated block from a list of free blocks. However the block was found to be already in use.

-

-

SYS-3-NZREFCNT

3-Error

Block [hec] on free list [dec] with refcount [dec]

A block of memory in the free pool is actually in use. The message indicates the number of processes using the memory block.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-WRONGFREELIST

3-Error

Block [hec] size [dec] on wrong free list [dec] [dec]

A freed buffer was placed on the wrong list of free buffers.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEMAGIC

3-Error

Corrupt free block at [hec] magic %08x

A block of memory at the indicated location is corrupt. An inconsistency was detected while checking the free memory area.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADPTRVAL

3-Error

Bad pointer value [chars] = [hec] in function [chars]

Corrupted pointer value is encountered.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEPTRS

3-Error

Bad [chars] pointer [hec] at [hec] [chars] = [hec]

A pointer in the block header at the indicated location is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-GETBUF

2-Critical

Bad getbuffer bytes= [dec]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

-

SYS-2-INPUT_GETBUF

2-Critical

Bad getbuffer bytes= [dec] for interface= [chars]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

LOG_STD_ACTION

SYS-2-INLIST

2-Critical

Buffer in list ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-INLIST1

2-Critical

Buffer in list ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED1

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPOOL

2-Critical

Attempt to use buffer with corrupt pool pointer ptr= [hec] pool= [hec]

An memory management function attempted an operation that could not be performed due to invalid memory pool descriptors.

-

-

SYS-2-BADPOOLMAGIC

2-Critical

Attempt to use pool pointer with corrupt header pool= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-WRONGPOOL

2-Critical

Buffer [hec] found in pool [hec] should be in pool [hec]

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-2-BADBUFFER

2-Critical

Attempt to use [chars] buffer as [chars] ptr= [hec] pool= [hec]

A hardware or software error occurred. An inconsistency was encountered while processing a packet buffer.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information."

SYS-2-QCOUNT

2-Critical

Bad [chars] [hec] count [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOTQ

2-Critical

[chars] didn't find [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-LINKED

2-Critical

Bad [chars] of [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SELFLINKED

2-Critical

Buffer [hec] linked to itself in free pool [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-ALREADYFREE

2-Critical

Buffer [hec] already in free pool [chars]

A block of memory at the indicated location is corrupt and/or has been erroneously freed twice.

os

"If this message recurs copy it exactly as it appears and the output " "of 'show buffer address <number>' for the given address as well as " "'show buffer pool <name> dump' for the given pool. Report it to your " "technical support representative."

SYS-2-LOWMEMPROC

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available processor memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak copy the message exactly as it appears and " "report it to your technical support representative. Otherwise you may " "need to add memory or reduce the number of features you are trying to " "support."

SYS-2-LOWMEMIO

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available IO memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak " "copy the message exactly as it appears and " "report it to your technical support representative. " "Otherwise you may need to add memory " "or reduce the number of features you are trying to " "support."

SYS-2-NOMEMFRGPROC

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous processor memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-NOMEMFRGIO

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous IO memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing " "copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-SPEC

2-Critical

Trying to set unknown special character [dec] to [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-ABRUPTTERM

3-Error

Abrupt termination of tty session for [chars] [t-line]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADDISP

3-Error

Bad disposal code [hec] in [chars]

An invalid status code has been passed to a buffer deletion routine. The buffer will be correctly returned to the free pool but will not be correctly counted in the per-protocol statistics.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NULLIDB

3-Error

Null IDB in [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-1-OVERTEMP

1-Alert

System detected OVERTEMPERATURE condition.\n Please resolve cooling problem immediately!\n

The environmental monitor detected a high-temperature condition.

none

"Make sure that the room temperature is not too high and that air flow " "to the card is not blocked. If this condition persists the " "environmental monitor might shut down the system. Call your technical " "support representative for assistance if necessary."

SYS-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADRESID

3-Error

Clock hardware returned bad residual [dec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPRINT

3-Error

Process has no associated tty in [chars].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-INTPRINT

3-Error

Illegal printing attempt from interrupt level.

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-OVFPRINT

3-Error

Overflow in [chars] chars [dec] buffer size [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NOELEMENT

3-Error

[chars]:Ran out of buffer elements for enqueue

The process was unable to enqueue data as it ran out of buffer elements.

-

"Copy the error message exactly as it appears also get the " "output of show buffers and report it to your technical support " "representative."

SYS-6-CLOCKUPDATE

6-Information

System clock has been updated from [chars] to [chars] configured from [chars] by [chars].

This message indicates that the system clock has been modified.

-

"This is informational message."

SYS-5-TABLEERR

5-Notice

[chars] table [chars] damaged: [chars].

An internal table entry became corrupt.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-3-BADTREEPARAM

3-Error

Bad parameter for [chars] passed to tree library function.

This message indicates that a pointer passed to a tree library function is invalid.

-

LOG_STD_SH_TECH_ACTION

SYS-2-BADLIST

2-Critical

Regular expression access check with bad list [dec]

This message indicates that a pointer to an access list is invalid.

-

"The event that caused this message to be issued should not " "have occured. It can mean that one or more data structures " "have been overwritten. If this message recurs and you decide " "to report it to your technical representative you should " "copy the text of the message exactly as it appears and " "include the associated stack trace." "\n\n Since access list corruption may have occurred " "a technical representative should verify that access " "lists are functioning corectly."

SYS-2-SNMP0IDX

2-Critical

Attempt to [chars] snmpidb with if_index of 0

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-SNMP_WRITENET

4-Warning

SNMP WriteNet request. Writing current configuration to [inet]

SNMP is writing the current configuration to a network host.

none

"These are notification messages only. No action is required."

SYS-4-SNMP_HOSTCONFIGSET

4-Warning

SNMP hostConfigSet request. Loading configuration from [inet]

SNMP is reading the host configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-SNMP_NETCONFIGSET

4-Warning

SNMP netConfigSet request. Loading configuration from [inet].

SNMP is reading the network configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-INVALID_IMAGE

4-Warning

Running invalid image for platform!

The software image being run is for a different hardware architecture. This problem can occur on a Cisco 1003 Cisco 1004 or Cisco 1005. The Cisco 1003 and Cisco 1004 use a different image from the Cisco 1005.

none

"Install the correct software image."

SYS-2-CHUNKBOUNDS

2-Critical

Could not find the sibling to allocate memory from. Chunk [chars] total free [dec] inuse [dec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBOUNDSIB

2-Critical

Error noticed in the sibling of the chunk [chars] Chunk index : [dec] Chunk real max : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKFREE

2-Critical

Attempted to free nonchunk memory chunk [hec] data [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKSIBLINGDEST

2-Critical

Attempted to destroy a sibling chunk [hec] [chars].

-

-

-

SYS-2-CHUNKSIBLINGS

2-Critical

Attempted to destroy chunk with siblings chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKPARTIAL

2-Critical

Attempted to destroy partially full chunk chunk 0x[hec] chunk name: \[chars]\.

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKBADMAGIC

2-Critical

Bad magic number in chunk header chunk [hec] data [hec] chunkmagic [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-6-INVALID_BOOTTIME

6-Information

Time since last reboot not available

This is an informational message for the user. The time taken for the router to come up after OIR is not available.

-

"No action required."

SYS-6-BOOTTIME

6-Information

Time taken to reboot after reload = %-4d seconds

This is an informational message for the user. This provides the time taken for the router to come up after reload or crash. The time is actually the difference between the last crash and a successive boot. If autoboot was not set and router is in rommon for a long time then the reload time shown could be large.

-

"No action required."

SYS-2-CHUNKBADREFCOUNT

2-Critical

Bad chunk reference count chunk [hec] data [hec] refcount [hec] alloc pc [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOMEMORY

2-Critical

* Could not allocate chunks for [chars]. No memory

* A software error occurred.

-

* "Copy the error message exactly as it appears and report it to " * "your technical support representative."

SYS-2-CHUNKEXPANDFAIL

2-Critical

Could not expand chunk pool for [chars]. No memory available

There is not enough processor memory left to grow this chunk pool.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADFREEMAGIC

2-Critical

Bad free magic number in chunk header chunk [hec] data [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOROOT

2-Critical

Root chunk need to be specified for [hec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINVALIDHDR

2-Critical

Invalid chunk header type [dec] for chunk [hec] data [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-CRASHINFOINITFAIL

3-Error

Crashinfo subsys initialization did not add registry \n\ crashinfo_get_default_file_name.\n

In order to figure out the device which the crashinfo writes to the crashinfo subsys has to add the registry crashinfo_get_default_file_name.

-

"Use Topic to search for a similar DDTS. If you find none write " "a DDTS for this problem. This SHOULD never happen - it is an " "indication of a bug elsewhere in the code."

SYS-2-CHUNKBADPOOLSIZE

2-Critical

Bad poolsize returned by the system : [dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINCONSIS

2-Critical

Inconsistant counters for chunk : [chars] total free [dec]/[dec] total sibs [dec]/[dec] total alloc [dec]/[dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADELESIZE

2-Critical

Chunk element size is more than 64k for [chars]

Chunk manager cannot function properly with big chunk elements

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-NULLCHUNK

2-Critical

Memory requested from Null Chunk

Chunk manager cannot allocate memory from NULL chunks

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNKSIBLINGSEXCEED

4-Warning

Number of siblings in a chunk has gone above the threshold. Threshold:[dec] Sibling-Count:[dec] Chunk:0x[hec] Name:[chars]

Number of siblings in a chunk with no header has gone above the default/configured threshold configured using <cmdBold>memory chunk siblings threshold<nocmdBold> <cmdArgs>count<nocmdArgs>

-

LOG_STD_SH_TECH_ACTION

SYS-1-CCA_SYS_ERR

1-Alert

CCA Detected System Error code = [dec]

CCA has detected a severe system software error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-2-CCA_INT_ERR

2-Critical

CCA Detected Logic Error code = [dec]

CCA has detected a severe internal logic error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-3-TIMERNEG

3-Error

Cannot start timer [hex] with negative offset [dec].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-MGDTIMER

3-Error

[chars][chars] timer = [hec].

This message indicates an error in a system timer. The problem can be caused either by software or by hardware.

-

-

SYS-3-DMPMEM

3-Error

%08x: %08x %08x %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-BOOT_MESSAGES

6-Information

Messages above this line are from the boot loader.\n

At least one informational or error message was printed by the boot loader.

-

"If the system image was loaded no action is recommended. If the " "system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-2-EXCEPTIONDUMP

2-Critical

System Crashed Writing Core....

The system has crashed because of an exception A core is being generated

-

LOG_STD_ACTION

SYS-3-LOGGER_FLUSHING

3-Error

System pausing to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system is paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_FLUSHED

3-Error

System was paused for %TE to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system was paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_DROPPED

3-Error

System dropped [dec] console debug messages.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

SYS-3-LOGGER_COUNT_STOP_CHUNK

3-Error

System cannot release chunk memory.\n

The system was not able to destroy a previously allocated chunk of memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-CHUNK_NO_EXMEM

3-Error

No handler to [chars] external memory.

An attempt was made to allocate or free a chunk of external memory but no handler for managing external memory was registered.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-READ_BOOTFILE_FAIL

6-Information

[chars] [chars].\n

A configured boot system command failed.

-

"If a system image was eventually loaded no action is recommended. If " "the system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-3-URLWRITEFAIL

3-Error

redirection url write failed '[chars]'

Redirection of output to URL failed.

-

"Check for free space on destination URL and retry."

SYS-6-READ_BOOTFILE_SKIP

6-Information

boot system [chars] command is skipped\n

A configured boot system command is skipped. Either the system experienced a crash while loading this image in the last attempt or the filename is not properly specified. Subsequent boot system commands will be tried

-

"Replace the failed boot system image with a good one. There could be " "various reasons that this specified image failed for example the image " "might be with a bad checksum."

SYS-6-USING_RESERVE_MEMORY

6-Information

Reserve memory is being used

The reserved memory is being used by the console

-

"The system is low in memory. The reserved memory will be " "used only by the console process. Please take a techsupport " "so that the reason for low memory can be found"

SYS-6-RESERVE_MEMORY_CREATED

6-Information

Reserve memory is being created

A portion of memory is reserved exclusively for console

-

"The console access is made available even in low memory " "condition. User can collect the details like tech-support " "for further diagnosis"

SYS-3-BAD_RESET

3-Error

Questionable reset of process [dec] on tty[t-line]\n

A process was reset without giving it a chance to clean itself up.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-DUP_TIMER

3-Error

Same tty[t-line] in linewatch_timers type [dec]

A tty appeared twice in a timer list where it should have only appeared once.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-LINEPROCDEAD

2-Critical

Killing process [chars] associated with line [dec]

A process associated with a tty line was killed by another process. The line may go dead

exec

"If this messages recurs copy it exactly as it appears " "and report it to your technical support representative."

SYS-3-HTIMER_EXPAND

3-Error

timer heap at 0x[hec] needed to expand but hasn't

A timer heap should have expanded but has not

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_INIT

3-Error

heap timer at 0x[hec] has not been initialized

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_STATE

3-Error

heap timer at 0x[hec] in state [dec]

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-MUNMAP

2-Critical

Could not return memory Neutrino via munmap at %lx size [dec] errno [dec]

Failued to unmap memory memory at the indicated location. The memory could not be unmapped because it was allocated via mmap.

-

-

SYS-2-MMAP

2-Critical

mmap failed for size [dec] bytes Caller PC 0x[hec] errno [dec]

Failed to allocate memory for the requested size. The memory could not be mapped because there is no memory.

-

-

SYS-3-CERF_RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a cache error

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CERF_ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-PAK_SUBBLOCK_SETSIZE

2-Critical

[dec]

This message indicates an error in startup code to register a pak subblock size. An attempt was made to register a size after the subblock chunk pool had been initialized. This problem is caused by software initialization order.

-

-

SYS-3-RGCREATEFAIL

3-Error

Resource group creation failed\nCause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGADDFAIL

3-Error

Couldn't add process process pid [dec] to resource group [hec]\n Cause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGDELEFAIL

3-Error

Couldn't delete process process pid [dec] from resource group\n \nCause: [chars]

An attempt to remove a process from a resource group failed at the indicated location

-

-

SYS-3-RGDESTFAIL

3-Error

Couldn't destroy resource group [hec]\nCause: [chars]

An attempt to destroy a resource group failed at the indicated location

-

-

SYS-3-RGOPFAIL

3-Error

Requested memory thresholding operation on resource group failed\n Resource Group handle: [hec] Cause: [chars]

The message indicates that an request to Set/Get memory thresholding data or enable/disable thresholding failed in the indicated location

The component that issued the request

-

SYS-3-RGMEMEXCEED

3-Error

\nLimit Exceeded: [chars] Holding: %lu Requested:%lu bytes

A resource group has requested for more memory than the configured limit at the indicated location

The component to which the offending resource group belongs.

-

SYS-2-PAK_SUBBLOCK_BADSIZE

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. The requested size is larger than the maximum registered subblock size.

-

-

SYS-2-PAK_SUBBLOCK_ALREADY

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. A subblock was already associated with the packet.

-

-

SYS-3-IMAGE_TOO_BIG

3-Error

'[chars]' is too large for available memory [dec] bytes.

The allocated memory for the image is too small to hold the image file.

-

"Increase the amount of memory available in the router by booting " "with a smaller image not enabling non-essential sub-systems " "or upgrading the installed memory. Call your technical " "support representative for assistance."

SYS-2-BAD_BM_ARG

2-Critical

Invalid BM index boolean used as argument [dec]

An illegal boolean manager index argument was referenced

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-MAX_IDB_BM_EXCEEDED

2-Critical

BM bit allocation limit exceeded

The BM has exhausted all of the bits available for allocation

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-BAD_BM_NAME

2-Critical

Invalid BM name

An illegal name string was registered with the BM

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-ASSERTION_FAILED

2-Critical

Assertion failed: \[chars]\

An internal state consistency check failed. Correct operation cannot be guaranteed and the system has been halted.

-

LOG_STD_ACTION

SYS-6-STARTUP_CONFIG_IGNORED

6-Information

System startup configuration is ignored based on the configuration register setting.

The configuration register was set to ignore the system startup configuration.

-

"If the system should ignore the startup configuration no action " "is required. If the system should boot with the startup configuration " "saved in the NVRAM change the configuration register value."

SYS-3-URLREADFAIL

3-Error

cannot open file for reading '[chars]'

The URL for the cannot be opened for reading.

-

"Check for proper Uniform Resource Locator syntax and for read " "permission and retry."

SYS-3-TCLSETFAIL

3-Error

cannot set TCL interpreter variable '[chars]' to '[chars]' : '[chars]'

The value could not be passed to the TCL interpreter

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-ESMSHUTDOWN

7-Debug

ESM shutdown

The Embedded Syslog Manager has been shut down

-

LOG_STD_NO_ACTION

SYS-6-LOGGINGHOST_STARTSTOP

6-Information

Logging to host [chars][chars][chars][chars]

Syslog logging to specified server or hostvrf has started or stopped

os-logging

LOG_STD_NO_ACTION

SYS-4-CPURESRISING

4-Warning

[chars][chars] is seeing [chars] cpu util [dec]%% at [chars] level more than the configured [chars] limit [dec] %%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped. CPURESRISING notifications should be matched with the corresponding CPURESFALLING/CPURESUNAPPLY notification.

-

"No action is required"

SYS-6-CPURESFALLING

6-Information

[chars][chars] is no longer seeing [chars] high cpu at [chars] level for the configured [chars] limit [dec]%% current value [dec]%%

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required"

SYS-6-CPURESUNAPPLY

6-Information

[chars][chars] is no longer monitoring [chars] cpu at [chars] level for the configured [chars] limit.

CPU usage is no loger monitored for the configured threshold level mentioned in the error message The corresponding policy is revoked.

-

"No action is required"

SYS-3-BADLIST_DESTROY

3-Error

Removed a non-empty list[hec] name: [chars] having %lu elements

A non-empty list should not be destroyed. If it happens there is a possibility that all elements enqueued into the list will never be deallocated. This message reports that an non-empty list got destroyed.

Determine the component from the stack trace and process name displayed in the error message.

LOG_STD_ACTION

SYS-2-SYSMEMINFO

2-Critical

System Memory: %luK total %luK used %luK free

This is an auxiliary message to several memory-related messages. It\n\ provides system memory information usage.

-

"This message provides additional information only. Copy the error \n\ message exactly as it appears and report it to your technical support \n\ representative as part of a previously printed error message."

SYS-6-LOGGING_BUGINF

6-Information

Logging of buginf debugs was [chars]

All calls to debugging have been disabled in Cisco IOS software as a result the user entering the <CmdBold>no logging buginf<NoCmdBold> command. This command is used to avoid a situation where a large amount of debugging calls might overload the processor CPU hog condition. This

os-logging

"This is an informational message only. No action is required."

SYS-5-FIFOBUS_ERR

5-Notice

Flow-control threshold on module [dec] has exceeded the default value. Threshold will be set to lower value

The FIFO threshold values are monitored for flow-control. When the threshold value exceeds the default the value is set to new lower value

Cat6000-env

LOG_STD_NO_ACTION

SYS-5-PRIV_AUTH_PASS

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_AUTH_FAIL

5-Notice

Authentication to Privilage level [dec] failed by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_I

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

CEF_SHIM_FIB-3-FIBTOPO

3-Error

Error for topology [dec]: [chars]

CEF_SHIM_FIB_INTERNAL_ERROR

CEF_SHIM_DDTS_COMPONENT

LOG_STD_ACTION

SYS-4-GD_DATAUNRELIABLE

4-Warning

Update to memory leak detector on free of 0x[hec] failed CLI output is unreliable\n

managed chunk malloc to store the range that is freed while memory leak detector is in progress failed. Hence memory leak detector will not be updated of this free and this can be reported as leak which is false.

mem

"Ignore the output of \"show memory debug leaks..\" if system is in low " "memory condition else perform a bug toolkit search on the web for " "existing bugs related to this error message if none found contact TAC " "for this problem providing \"show version\" and " "\"show memory statistics\" output."

SYS-3-GD_STACKERR

3-Error

Unknown stack. Process: [chars]\n

An internal error occurred when running the memory leak detector

mem

"Copy the error message exactly as it appears on the console or in the" " system log and look up the message in the Bug Toolkit at:" " http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you are" " unable to resolve the issue using Bug Toolkit please issue a" " \"show tech\" and contact your technical support representative" " with the gathered information."

SYS-4-FREEMEMLOW

4-Warning

Free Memory has dropped below low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-5-FREEMEMRECOVER

5-Notice

Free Memory has recovered above low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the free memory in that pool is now above the configured low-memory limit.

-

"No action is required"

SYS-2-MALLOCFAIL

2-Critical

Memory allocation of [dec] bytes failed from [hex] alignment [dec] \n Pool: [chars] Free: [dec] Cause: [chars] \nAlternate Pool: [chars] Free: [dec] Cause: [chars] \n

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error may have exhausted or fragmented the router's memory.

mem-suspect

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representativeand provide the representative with the gathered information. " "Otherwise you may need to add more memory or reduce the number of " "features you are trying to support."

SYS-2-MUTEXLOCKFAIL

2-Critical

pthread_mutex_lock failed for [chars]

The thread failed in pthread_mutex_lock while trying to acquire a mutex.

mem-suspect

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-NOMEMORY

2-Critical

No memory available for [chars] [dec]

An operation could not be accomplished because of a low-memory condition. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

mem-suspect

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a configuration that has more memory."

SYS-3-CRITMEM

3-Error

[chars]

An attempt to allow or disallow a process from using memory that has been reserved for critical purposes has failed. The location of the failure is specified in the error message. This condition could possibly be caused by a software error.

mem-suspect

"Copy the error message and the traceback messages exactly as they appear " "on the colsole or in the system log contact your technical support " "representative and provide the representative with the gathered " "information."

SYS-2-GETBUFFFAIL

2-Critical

[chars] buffer allocation [dec] bytes failed from [hex]

-

-

-

SYS-6-NOBRIDGE

6-Information

Bridging software not present

Your system is not configured to be a bridge.

none

"Configure the bridging software."

SYS-3-SOCKUNKN

3-Error

Unknown socket protocol [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-HARIKARI

3-Error

Process [chars] top-level routine exited

An internal software error occurred

Determine the component from the process name displayed in the error message.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPID

2-Critical

Bad pid [dec] for tty [t-line]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-MGDTMRRUN

3-Error

TTY[t-line]: Managed Timers [chars] still running

One or more managed timers for a TTY that is deleted are still running.

-

LOG_STD_ACTION

SYS-0-USERLOG_EMERG

0-Emergency

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-1-USERLOG_ALERT

1-Alert

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-2-USERLOG_CRIT

2-Critical

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only. "

SYS-3-USERLOG_ERR

3-Error

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-4-USERLOG_WARNING

4-Warning

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-5-USERLOG_NOTICE

5-Notice

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-6-USERLOG_INFO

6-Information

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-7-USERLOG_DEBUG

7-Debug

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-3-MSGLOST

3-Error

[dec] messages lost because of queue overflow

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-REGEXP

4-Warning

[chars].

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-5-RESTART

5-Notice

System restarted --\n[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SCHEDULED_RELOAD

5-Notice

Reload requested for [chars]

A scheduled reload has been requested for the router.

none

"No action is required."

SYS-5-SCHEDULED_RELOAD_CANCELLED

5-Notice

Scheduled reload cancelled at [chars]

A scheduled reload that was requested for the router has been cancelled.

none

"No action is required."

SYS-5-RELOAD

5-Notice

Reload requested[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SWITCHOVER

5-Notice

Switchover requested[chars]

A switchover was requested.

none

"This is a notification message only. No action is required."

SYS-4-RELOAD_ATTEMPT

4-Warning

Attempt via SNMP failed system shutdown not configured

SNMP cannot be used to reload the router unless this functionality has been previously configured. This message reports that an attempt to reload the router failed because SNMP reloads are not currently configured on the router.

none

"This is a notification message only. No action is required."

SYS-3-CFG_AT_RELOAD

3-Error

System reloading unable to complete startup configuration update

Startup configuration updation is already in progress and reload has been called either from interrupt level or with all interrupts disabled. Reload can not suspend to let startup configuration updation get completed. Startup configuration may get corrupted.

none

"This is a notification message only. No action is required."

SYS-4-DUAL_MESSAGE

4-Warning

SNMP system message request [dec] denied because of pending job

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-5-CONFIG

5-Notice

Configured from [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_I

5-Notice

Configured from [chars] by [chars]

The write of the system running configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_RESOLVE_FAILURE

4-Warning

System config parse from [chars] failed

The configuration file from the URL specified in the error message could not be read.

-

"Enter the <CmdBold>no service config<NoCmdBold> " "command to disable autoloading of configuration files " "OR investigate why the tftp load is failing."

SYS-5-CONFIG_NV

5-Notice

Nonvolatile storage configured from [chars]

The configuration was written successfully.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_NV_I

5-Notice

Nonvolatile storage configured from [chars] by [chars]

The write of the nonvolatile configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-CONFIG_NV_DATA

3-Error

Variable [chars] not set properly in the routine [chars].

The write of the nonvolatile configuration failed because an internal variable was not set properly.

-

"If this messages occurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_NEWER

4-Warning

Configuration from version [dec].[dec] may not be correctly understood

The software detected that the configuration saved in memory was written by a newer version of software. There might be commands saved in memory that are not implemented by the older software version.

none

"Examine all the messages printed while the router was " "booting. For each message about an unknown command determine " "whether that feature is required. If so upgrade to a " "newer version of software that supports that feature."

SYS-4-CONFIG_NOLOCK

4-Warning

The configuration could not be locked

A software error occurred.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SYS-3-CONFIG_NO_PRIVATE

3-Error

No space remaining to save private config

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-CONFIG_NV_OVERRUN

4-Warning

Non config data present at the end of nvram is corrupted

The software detected that the configuration saved into nvram has overlaid a part of the nvram occupied by non config data files.Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_TRUNCATE

4-Warning

Truncated configuration to %ld bytes from %ld bytes

The software detected that the configuration saved into nvram has been truncated. There was not enough space to save the compressed configuration.

-

"Save the configuration to flash if the platform supports " " \"boot config\" command."

SYS-4-CONFIG_NV_NEED_OVERRUN

4-Warning

Non config data present at the end of nvram needs to be overwritten to fit the configuration into nvram

The software detected that the non config data files occupying the end of nvram need to be overwritten to fit the configuration. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_NEED_TRUNCATE

4-Warning

Configuration needs to be truncated to fit into nvram

The software detected that the configuration is to be truncated to fit in the nvram. There was not enough space to save the compressed configuration

-

"Save the configuration to flash if the platform supports " "\"boot config nvbypass\" command."

SYS-4-NV_BLOCK_INITFAIL

4-Warning

Unable to initialize the geometry of nvram

The software detected that it failed to initialize the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload. This may happen when the entire nvram is packed with the configuration and the newer version of software which supports this feature could not find the minimum room in the nvram to initialize block file system.

-

"Reduce the configurations in the nvram atleast by 2K"

SYS-7-NV_BLOCK_INIT

7-Debug

Initialized the geometry of nvram

Initialized the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

""

SYS-4-NV_CHKSUM

4-Warning

An nvram checksum is already in progress

An interrupt service routine attempted to perform a checksum on the nvram contents and found the resource in use.

nvram

-

SYS-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMINIT

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be initialized. reasons are not clear.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent data some corruption.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CONFIG_DOWNFAIL

2-Critical

Generated configuration not backward compatible

The router has been configured to generate nonvolatile memory using the commands of an older software version. The current configuration of the router contains a command that cannot be saved using only the older command set.

none

"Allow the router to save the configuration using the command set of " "the current software version or remove the commands that cannot be " "saved using the older command set."

SYS-5-OUTSETUP

5-Notice

Configuration file [chars] accepted aborting setup

A configuration was accepted over the network so the setup session will be aborted.

none

"This is a notification message only. No action is required."

SYS-3-BADLINKTYPE

3-Error

* Unexpected linktype [dec]

* A software error occurred.

udp

* "Copy the error message exactly as it appears and report it to your " * "technical support representative."

SYS-2-SIGNUM

2-Critical

Process aborted on invalid signal signum = [dec].

An attempt was made to send an invalid signal to another process.

-

"If this message occurs more than once report this message " "to your technical support representative."

SYS-3-CPUHOG

3-Error

Task is running for [dec]msecs more than [dec]msecs [dec]/[dec]

The indicated process ran too long without relinquishing the processor. Each process should run for a small amount of time and then relinquish the CPU so that other processes can run. This problem can be caused by many things like traffic or system load hardware or operational configuration a configuration change initialization of many interfaces cards or ports for example a high momentary error rate a sustained abnormal

If this error occurs in conjunction with a TIMERHOG message \n\ report the two errors together and use the component obtained \n\ for the TIMERHOG message.

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representative and provide the representative with the gathered information."

SYS-2-WATCHDOG

2-Critical

Process aborted on watchdog timeout process = [chars].[chars]

The indicated process ran for too long without relinquishing control. The system killed it as a runaway process.

-

-

SYS-3-TIMERHOG

3-Error

Timer callback ran long PC = [hec].

The indicated callback routine ran for too long without relinquishing the processor.

Determine the component from the callback routine address displayed in\n\ the error message. Use Topic to search for a similar DDTS. If you \n\ find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-6-STACKLOW

6-Information

Stack for [chars] [chars] running low [dec]/[dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-GREEDY_REGEXP

4-Warning

[chars] while processing the input regular expression. Aborting processing use alternate regular expression. Input regular expression: \[chars]\

Regular expression processing limitation: Certain regular expressions require huge stack space for processing or can lead to processing timeouts. We abort processing such regular expressions and print this message to avoid stack overflow/unexpected reload.

os

"The regular expression specified leads to stack overflow/processing " "timeout of the indicated process. Recommended to use a different " "regular expression."

SYS-1-CPURISINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr: [dec]%%/[dec]%%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped.

-

"Enter the <CmdBold>show processes CPU<NoCmdBold>" " command to determine the CPU hogging process" " that is causing this condition and if possible" " disable the activity that is causing the" " CPU hog condition so that CPU" " utilization is reduced."

SYS-1-CPUFALLINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr [dec]%%/[dec]%%.

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required."

SYS-2-INPUTQ

2-Critical

INPUTQ set but no IDB ptr=[hec]

This message is issued when an attempt is made to alter the input queue count for a packet that should not be counted.

-

-

SYS-6-BADSHAREINFO

6-Information

[chars] packet [hec] has a zero reference count freeing pid = [hec] \n\ freeing pc = [hec] [chars].

Provides additional information about original freer of packet.

-

-

SYS-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[hec]

A reference count is used to track the usage of many data structures. A function increments the count when it begins to use a structure and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be negative which means that the data structure will not be freed until the system is reloaded.

-

-

SYS-2-CFORKLEV

2-Critical

Process creation of [chars] failed at level [dec].

An internal software error occurred.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKMEM

2-Critical

Process creation of [chars] failed no memory.

Insufficient memory was available to create a process either while trying to support additional features or due to a memory leak.

mem-suspect

"A memory leak may be the cause if the system has been running for a " "while without changing its configuration. If you suspect a leak then " "copy this message exactly as it appears and report it to your technical " "support representative. Otherwise ensure that more memory is available " "to support the additional features."

SYS-2-CFORKBADFUNCT

2-Critical

Can't create process with start address = [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPROCESS

3-Error

Bad process ID [dec] when [chars] process table

An internal software error occurred.

os-scheduler

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INSCHED

2-Critical

[chars] within scheduler

-

Determine the component from the stack trace displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem.

-

SYS-2-NOTIOSTASK

2-Critical

[chars] from outside IOS task context

An IOS reschedule request was made from code that is not running in the context of an IOS task -- from an interrupt handler the scheduler itself or a service pthread within the IOS process.

Determine the component from the stack trace displayed in the\n\ error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INTSCHED

2-Critical

'[chars]' at level [dec]

The scheduler was entered from an interrupt service routine ISR.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

-

SYS-3-PROCSEMFAIL

3-Error

Process semaphore creation for preemptive processes failed.

Creation of process function semaphore to protect the critical section of process create routine failed. The semaphore creation can fail if there isnt enough chunk memory to create the event structure.

os

-

SYS-2-NOBLOCK

2-Critical

[chars] with blocking disabled.

A process aattempted to relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

-

SYS-2-BLOCKHUNG

2-Critical

Task hung with blocking disabled value = 0x[hec].

The indicated process has exceeded the time limit for which it may relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

"This message may be a result of high loads. If it recurs " "copy the text exactly as it appears and report it along " "with the associated stack trace to your technical support " "representative."

SYS-2-NOTDEAD

2-Critical

Killing process [chars] pid [dec] again

An internal software error occurred.

os-scheduler

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOPROCESS

2-Critical

No such process [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-IMMORTAL

2-Critical

Attempt to shut down management process [dec] [chars].

An attempt was made to shut down the specified management process. Management processes must not be shut down as long as the\n\ router remains up.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the process_kill.

-

SYS-2-SIGPENDING

2-Critical

Multiple Signals are sent to a process [dec]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADSTACK

2-Critical

Process [chars] has trashed stack old size [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-6-MTRACE

6-Information

[chars]: addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC

This is an auxiliary message to several memory-related messages. It provides the address of the memory block and the calling program counter for the last eight blocks allocated and for the last eight blocks freed.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of a previously printed error message."

SYS-6-BLKINFO

6-Information

[chars]blk [hec] words [dec] alloc [hec] [chars] dealloc [hec] rfcnt [hec]

This is an auxiliary message to several memory-related messages. It provides a formatted display of some of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-MEMDUMP

6-Information

[hex]: [hex] [hex] [hex] [hex]

This is an auxiliary message to several memory-related messages. It provides a raw display of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-PROCINFO

6-Information

Process [chars] just finished executing

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

-

"Copy this messages exactly as it appears and report it along with " "the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your " "technical support representative."

SYS-6-TESTINFO

6-Information

Scheduler test [hex] for [chars] just executed

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

Determine the component from the address of the scheduler test routine\n\ displayed in the error message.\n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy this message exactly as it appears and report it along with the " "SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical " "support representative."

SYS-3-BADBLOCK

3-Error

Bad block pointer [hec]

A block of memory at the indicated location is corrupt. An internal check of memory block pointers indicates an inconsistency.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to auotmatically reload then the router will " "need to reloaded manually."

SYS-3-BADMAGIC

3-Error

Corrupt block at [hec] magic %08x

The free memory pool is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADREFCOUNT

3-Error

Bad reference count at [hec] refcount [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-3-OVERRUN

3-Error

Block overrun at [hec] red zone %08x

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-FREEBAD

2-Critical

Attempted to free memory at [hec] not part of buffer pool

An attempt was made to free memory but the request could not be completed due to an invalid memory data structure

-

-

SYS-2-FREEFREE

2-Critical

Attempted to free unassigned memory at %lx alloc %lx dealloc %lx

An attempt was made to free memory at the indicated location. The memory could not be freed because it was not allocated.

-

-

SYS-3-INVMEMINT

3-Error

Invalid memory action [chars] at interrupt level

This message indicates that a memory allocation or deallocation was attempted from an interrupt handler.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-INVMEMPID

3-Error

Invalid pid [dec] in block: [hec]

There has been attempt to allocate memory on behalf of an invalid process.

mem

-

SYS-3-MEMSEMFAIL

3-Error

Mempool semaphore creation failed for [chars]

This message indicates that the semaphore creation for the specified mempool failed.

-

-

SYS-3-INUSEFREE

3-Error

Block [hec] on free list [dec] in use

A memory management function attempted to allocate the indicated block from a list of free blocks. However the block was found to be already in use.

-

-

SYS-3-NZREFCNT

3-Error

Block [hec] on free list [dec] with refcount [dec]

A block of memory in the free pool is actually in use. The message indicates the number of processes using the memory block.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-WRONGFREELIST

3-Error

Block [hec] size [dec] on wrong free list [dec] [dec]

A freed buffer was placed on the wrong list of free buffers.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEMAGIC

3-Error

Corrupt free block at [hec] magic %08x

A block of memory at the indicated location is corrupt. An inconsistency was detected while checking the free memory area.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADPTRVAL

3-Error

Bad pointer value [chars] = [hec] in function [chars]

Corrupted pointer value is encountered.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEPTRS

3-Error

Bad [chars] pointer [hec] at [hec] [chars] = [hec]

A pointer in the block header at the indicated location is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-GETBUF

2-Critical

Bad getbuffer bytes= [dec]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

-

SYS-2-INPUT_GETBUF

2-Critical

Bad getbuffer bytes= [dec] for interface= [chars]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

LOG_STD_ACTION

SYS-2-INLIST

2-Critical

Buffer in list ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-INLIST1

2-Critical

Buffer in list ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED1

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPOOL

2-Critical

Attempt to use buffer with corrupt pool pointer ptr= [hec] pool= [hec]

An memory management function attempted an operation that could not be performed due to invalid memory pool descriptors.

-

-

SYS-2-BADPOOLMAGIC

2-Critical

Attempt to use pool pointer with corrupt header pool= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-WRONGPOOL

2-Critical

Buffer [hec] found in pool [hec] should be in pool [hec]

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-2-BADBUFFER

2-Critical

Attempt to use [chars] buffer as [chars] ptr= [hec] pool= [hec]

A hardware or software error occurred. An inconsistency was encountered while processing a packet buffer.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information."

SYS-2-QCOUNT

2-Critical

Bad [chars] [hec] count [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOTQ

2-Critical

[chars] didn't find [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-LINKED

2-Critical

Bad [chars] of [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SELFLINKED

2-Critical

Buffer [hec] linked to itself in free pool [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-ALREADYFREE

2-Critical

Buffer [hec] already in free pool [chars]

A block of memory at the indicated location is corrupt and/or has been erroneously freed twice.

os

"If this message recurs copy it exactly as it appears and the output " "of 'show buffer address <number>' for the given address as well as " "'show buffer pool <name> dump' for the given pool. Report it to your " "technical support representative."

SYS-2-LOWMEMPROC

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available processor memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak copy the message exactly as it appears and " "report it to your technical support representative. Otherwise you may " "need to add memory or reduce the number of features you are trying to " "support."

SYS-2-LOWMEMIO

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available IO memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak " "copy the message exactly as it appears and " "report it to your technical support representative. " "Otherwise you may need to add memory " "or reduce the number of features you are trying to " "support."

SYS-2-NOMEMFRGPROC

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous processor memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-NOMEMFRGIO

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous IO memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing " "copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-SPEC

2-Critical

Trying to set unknown special character [dec] to [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-ABRUPTTERM

3-Error

Abrupt termination of tty session for [chars] [t-line]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADDISP

3-Error

Bad disposal code [hec] in [chars]

An invalid status code has been passed to a buffer deletion routine. The buffer will be correctly returned to the free pool but will not be correctly counted in the per-protocol statistics.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NULLIDB

3-Error

Null IDB in [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-1-OVERTEMP

1-Alert

System detected OVERTEMPERATURE condition.\n Please resolve cooling problem immediately!\n

The environmental monitor detected a high-temperature condition.

none

"Make sure that the room temperature is not too high and that air flow " "to the card is not blocked. If this condition persists the " "environmental monitor might shut down the system. Call your technical " "support representative for assistance if necessary."

SYS-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADRESID

3-Error

Clock hardware returned bad residual [dec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPRINT

3-Error

Process has no associated tty in [chars].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-INTPRINT

3-Error

Illegal printing attempt from interrupt level.

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-OVFPRINT

3-Error

Overflow in [chars] chars [dec] buffer size [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NOELEMENT

3-Error

[chars]:Ran out of buffer elements for enqueue

The process was unable to enqueue data as it ran out of buffer elements.

-

"Copy the error message exactly as it appears also get the " "output of show buffers and report it to your technical support " "representative."

SYS-6-CLOCKUPDATE

6-Information

System clock has been updated from [chars] to [chars] configured from [chars] by [chars].

This message indicates that the system clock has been modified.

-

"This is informational message."

SYS-5-TABLEERR

5-Notice

[chars] table [chars] damaged: [chars].

An internal table entry became corrupt.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-3-BADTREEPARAM

3-Error

Bad parameter for [chars] passed to tree library function.

This message indicates that a pointer passed to a tree library function is invalid.

-

LOG_STD_SH_TECH_ACTION

SYS-2-BADLIST

2-Critical

Regular expression access check with bad list [dec]

This message indicates that a pointer to an access list is invalid.

-

"The event that caused this message to be issued should not " "have occured. It can mean that one or more data structures " "have been overwritten. If this message recurs and you decide " "to report it to your technical representative you should " "copy the text of the message exactly as it appears and " "include the associated stack trace." "\n\n Since access list corruption may have occurred " "a technical representative should verify that access " "lists are functioning corectly."

SYS-2-SNMP0IDX

2-Critical

Attempt to [chars] snmpidb with if_index of 0

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-SNMP_WRITENET

4-Warning

SNMP WriteNet request. Writing current configuration to [inet]

SNMP is writing the current configuration to a network host.

none

"These are notification messages only. No action is required."

SYS-4-SNMP_HOSTCONFIGSET

4-Warning

SNMP hostConfigSet request. Loading configuration from [inet]

SNMP is reading the host configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-SNMP_NETCONFIGSET

4-Warning

SNMP netConfigSet request. Loading configuration from [inet].

SNMP is reading the network configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-INVALID_IMAGE

4-Warning

Running invalid image for platform!

The software image being run is for a different hardware architecture. This problem can occur on a Cisco 1003 Cisco 1004 or Cisco 1005. The Cisco 1003 and Cisco 1004 use a different image from the Cisco 1005.

none

"Install the correct software image."

SYS-2-CHUNKBOUNDS

2-Critical

Could not find the sibling to allocate memory from. Chunk [chars] total free [dec] inuse [dec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBOUNDSIB

2-Critical

Error noticed in the sibling of the chunk [chars] Chunk index : [dec] Chunk real max : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKFREE

2-Critical

Attempted to free nonchunk memory chunk [hec] data [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKSIBLINGDEST

2-Critical

Attempted to destroy a sibling chunk [hec] [chars].

-

-

-

SYS-2-CHUNKSIBLINGS

2-Critical

Attempted to destroy chunk with siblings chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKPARTIAL

2-Critical

Attempted to destroy partially full chunk chunk 0x[hec] chunk name: \[chars]\.

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKBADMAGIC

2-Critical

Bad magic number in chunk header chunk [hec] data [hec] chunkmagic [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-6-INVALID_BOOTTIME

6-Information

Time since last reboot not available

This is an informational message for the user. The time taken for the router to come up after OIR is not available.

-

"No action required."

SYS-6-BOOTTIME

6-Information

Time taken to reboot after reload = %-4d seconds

This is an informational message for the user. This provides the time taken for the router to come up after reload or crash. The time is actually the difference between the last crash and a successive boot. If autoboot was not set and router is in rommon for a long time then the reload time shown could be large.

-

"No action required."

SYS-2-CHUNKBADREFCOUNT

2-Critical

Bad chunk reference count chunk [hec] data [hec] refcount [hec] alloc pc [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOMEMORY

2-Critical

* Could not allocate chunks for [chars]. No memory

* A software error occurred.

-

* "Copy the error message exactly as it appears and report it to " * "your technical support representative."

SYS-2-CHUNKEXPANDFAIL

2-Critical

Could not expand chunk pool for [chars]. No memory available

There is not enough processor memory left to grow this chunk pool.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADFREEMAGIC

2-Critical

Bad free magic number in chunk header chunk [hec] data [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOROOT

2-Critical

Root chunk need to be specified for [hec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINVALIDHDR

2-Critical

Invalid chunk header type [dec] for chunk [hec] data [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-CRASHINFOINITFAIL

3-Error

Crashinfo subsys initialization did not add registry \n\ crashinfo_get_default_file_name.\n

In order to figure out the device which the crashinfo writes to the crashinfo subsys has to add the registry crashinfo_get_default_file_name.

-

"Use Topic to search for a similar DDTS. If you find none write " "a DDTS for this problem. This SHOULD never happen - it is an " "indication of a bug elsewhere in the code."

SYS-2-CHUNKBADPOOLSIZE

2-Critical

Bad poolsize returned by the system : [dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINCONSIS

2-Critical

Inconsistant counters for chunk : [chars] total free [dec]/[dec] total sibs [dec]/[dec] total alloc [dec]/[dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADELESIZE

2-Critical

Chunk element size is more than 64k for [chars]

Chunk manager cannot function properly with big chunk elements

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-NULLCHUNK

2-Critical

Memory requested from Null Chunk

Chunk manager cannot allocate memory from NULL chunks

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNKSIBLINGSEXCEED

4-Warning

Number of siblings in a chunk has gone above the threshold. Threshold:[dec] Sibling-Count:[dec] Chunk:0x[hec] Name:[chars]

Number of siblings in a chunk with no header has gone above the default/configured threshold configured using <cmdBold>memory chunk siblings threshold<nocmdBold> <cmdArgs>count<nocmdArgs>

-

LOG_STD_SH_TECH_ACTION

SYS-1-CCA_SYS_ERR

1-Alert

CCA Detected System Error code = [dec]

CCA has detected a severe system software error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-2-CCA_INT_ERR

2-Critical

CCA Detected Logic Error code = [dec]

CCA has detected a severe internal logic error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-3-TIMERNEG

3-Error

Cannot start timer [hex] with negative offset [dec].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-MGDTIMER

3-Error

[chars][chars] timer = [hec].

This message indicates an error in a system timer. The problem can be caused either by software or by hardware.

-

-

SYS-3-DMPMEM

3-Error

%08x: %08x %08x %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-BOOT_MESSAGES

6-Information

Messages above this line are from the boot loader.\n

At least one informational or error message was printed by the boot loader.

-

"If the system image was loaded no action is recommended. If the " "system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-2-EXCEPTIONDUMP

2-Critical

System Crashed Writing Core....

The system has crashed because of an exception A core is being generated

-

LOG_STD_ACTION

SYS-3-LOGGER_FLUSHING

3-Error

System pausing to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system is paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_FLUSHED

3-Error

System was paused for %TE to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system was paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_DROPPED

3-Error

System dropped [dec] console debug messages.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

SYS-3-LOGGER_COUNT_STOP_CHUNK

3-Error

System cannot release chunk memory.\n

The system was not able to destroy a previously allocated chunk of memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-CHUNK_NO_EXMEM

3-Error

No handler to [chars] external memory.

An attempt was made to allocate or free a chunk of external memory but no handler for managing external memory was registered.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-READ_BOOTFILE_FAIL

6-Information

[chars] [chars].\n

A configured boot system command failed.

-

"If a system image was eventually loaded no action is recommended. If " "the system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-3-URLWRITEFAIL

3-Error

redirection url write failed '[chars]'

Redirection of output to URL failed.

-

"Check for free space on destination URL and retry."

SYS-6-READ_BOOTFILE_SKIP

6-Information

boot system [chars] command is skipped\n

A configured boot system command is skipped. Either the system experienced a crash while loading this image in the last attempt or the filename is not properly specified. Subsequent boot system commands will be tried

-

"Replace the failed boot system image with a good one. There could be " "various reasons that this specified image failed for example the image " "might be with a bad checksum."

SYS-6-USING_RESERVE_MEMORY

6-Information

Reserve memory is being used

The reserved memory is being used by the console

-

"The system is low in memory. The reserved memory will be " "used only by the console process. Please take a techsupport " "so that the reason for low memory can be found"

SYS-6-RESERVE_MEMORY_CREATED

6-Information

Reserve memory is being created

A portion of memory is reserved exclusively for console

-

"The console access is made available even in low memory " "condition. User can collect the details like tech-support " "for further diagnosis"

SYS-3-BAD_RESET

3-Error

Questionable reset of process [dec] on tty[t-line]\n

A process was reset without giving it a chance to clean itself up.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-DUP_TIMER

3-Error

Same tty[t-line] in linewatch_timers type [dec]

A tty appeared twice in a timer list where it should have only appeared once.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-LINEPROCDEAD

2-Critical

Killing process [chars] associated with line [dec]

A process associated with a tty line was killed by another process. The line may go dead

exec

"If this messages recurs copy it exactly as it appears " "and report it to your technical support representative."

SYS-3-HTIMER_EXPAND

3-Error

timer heap at 0x[hec] needed to expand but hasn't

A timer heap should have expanded but has not

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_INIT

3-Error

heap timer at 0x[hec] has not been initialized

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_STATE

3-Error

heap timer at 0x[hec] in state [dec]

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-MUNMAP

2-Critical

Could not return memory Neutrino via munmap at %lx size [dec] errno [dec]

Failued to unmap memory memory at the indicated location. The memory could not be unmapped because it was allocated via mmap.

-

-

SYS-2-MMAP

2-Critical

mmap failed for size [dec] bytes Caller PC 0x[hec] errno [dec]

Failed to allocate memory for the requested size. The memory could not be mapped because there is no memory.

-

-

SYS-3-CERF_RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a cache error

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CERF_ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-PAK_SUBBLOCK_SETSIZE

2-Critical

[dec]

This message indicates an error in startup code to register a pak subblock size. An attempt was made to register a size after the subblock chunk pool had been initialized. This problem is caused by software initialization order.

-

-

SYS-3-RGCREATEFAIL

3-Error

Resource group creation failed\nCause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGADDFAIL

3-Error

Couldn't add process process pid [dec] to resource group [hec]\n Cause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGDELEFAIL

3-Error

Couldn't delete process process pid [dec] from resource group\n \nCause: [chars]

An attempt to remove a process from a resource group failed at the indicated location

-

-

SYS-3-RGDESTFAIL

3-Error

Couldn't destroy resource group [hec]\nCause: [chars]

An attempt to destroy a resource group failed at the indicated location

-

-

SYS-3-RGOPFAIL

3-Error

Requested memory thresholding operation on resource group failed\n Resource Group handle: [hec] Cause: [chars]

The message indicates that an request to Set/Get memory thresholding data or enable/disable thresholding failed in the indicated location

The component that issued the request

-

SYS-3-RGMEMEXCEED

3-Error

\nLimit Exceeded: [chars] Holding: %lu Requested:%lu bytes

A resource group has requested for more memory than the configured limit at the indicated location

The component to which the offending resource group belongs.

-

SYS-2-PAK_SUBBLOCK_BADSIZE

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. The requested size is larger than the maximum registered subblock size.

-

-

SYS-2-PAK_SUBBLOCK_ALREADY

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. A subblock was already associated with the packet.

-

-

SYS-3-IMAGE_TOO_BIG

3-Error

'[chars]' is too large for available memory [dec] bytes.

The allocated memory for the image is too small to hold the image file.

-

"Increase the amount of memory available in the router by booting " "with a smaller image not enabling non-essential sub-systems " "or upgrading the installed memory. Call your technical " "support representative for assistance."

SYS-2-BAD_BM_ARG

2-Critical

Invalid BM index boolean used as argument [dec]

An illegal boolean manager index argument was referenced

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-MAX_IDB_BM_EXCEEDED

2-Critical

BM bit allocation limit exceeded

The BM has exhausted all of the bits available for allocation

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-BAD_BM_NAME

2-Critical

Invalid BM name

An illegal name string was registered with the BM

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-ASSERTION_FAILED

2-Critical

Assertion failed: \[chars]\

An internal state consistency check failed. Correct operation cannot be guaranteed and the system has been halted.

-

LOG_STD_ACTION

SYS-6-STARTUP_CONFIG_IGNORED

6-Information

System startup configuration is ignored based on the configuration register setting.

The configuration register was set to ignore the system startup configuration.

-

"If the system should ignore the startup configuration no action " "is required. If the system should boot with the startup configuration " "saved in the NVRAM change the configuration register value."

SYS-3-URLREADFAIL

3-Error

cannot open file for reading '[chars]'

The URL for the cannot be opened for reading.

-

"Check for proper Uniform Resource Locator syntax and for read " "permission and retry."

SYS-3-TCLSETFAIL

3-Error

cannot set TCL interpreter variable '[chars]' to '[chars]' : '[chars]'

The value could not be passed to the TCL interpreter

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-ESMSHUTDOWN

7-Debug

ESM shutdown

The Embedded Syslog Manager has been shut down

-

LOG_STD_NO_ACTION

SYS-6-LOGGINGHOST_STARTSTOP

6-Information

Logging to host [chars][chars][chars][chars]

Syslog logging to specified server or hostvrf has started or stopped

os-logging

LOG_STD_NO_ACTION

SYS-4-CPURESRISING

4-Warning

[chars][chars] is seeing [chars] cpu util [dec]%% at [chars] level more than the configured [chars] limit [dec] %%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped. CPURESRISING notifications should be matched with the corresponding CPURESFALLING/CPURESUNAPPLY notification.

-

"No action is required"

SYS-6-CPURESFALLING

6-Information

[chars][chars] is no longer seeing [chars] high cpu at [chars] level for the configured [chars] limit [dec]%% current value [dec]%%

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required"

SYS-6-CPURESUNAPPLY

6-Information

[chars][chars] is no longer monitoring [chars] cpu at [chars] level for the configured [chars] limit.

CPU usage is no loger monitored for the configured threshold level mentioned in the error message The corresponding policy is revoked.

-

"No action is required"

SYS-3-BADLIST_DESTROY

3-Error

Removed a non-empty list[hec] name: [chars] having %lu elements

A non-empty list should not be destroyed. If it happens there is a possibility that all elements enqueued into the list will never be deallocated. This message reports that an non-empty list got destroyed.

Determine the component from the stack trace and process name displayed in the error message.

LOG_STD_ACTION

SYS-2-SYSMEMINFO

2-Critical

System Memory: %luK total %luK used %luK free

This is an auxiliary message to several memory-related messages. It\n\ provides system memory information usage.

-

"This message provides additional information only. Copy the error \n\ message exactly as it appears and report it to your technical support \n\ representative as part of a previously printed error message."

SYS-6-LOGGING_BUGINF

6-Information

Logging of buginf debugs was [chars]

All calls to debugging have been disabled in Cisco IOS software as a result the user entering the <CmdBold>no logging buginf<NoCmdBold> command. This command is used to avoid a situation where a large amount of debugging calls might overload the processor CPU hog condition. This

os-logging

"This is an informational message only. No action is required."

SYS-5-FIFOBUS_ERR

5-Notice

Flow-control threshold on module [dec] has exceeded the default value. Threshold will be set to lower value

The FIFO threshold values are monitored for flow-control. When the threshold value exceeds the default the value is set to new lower value

Cat6000-env

LOG_STD_NO_ACTION

SYS-5-PRIV_AUTH_PASS

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_AUTH_FAIL

5-Notice

Authentication to Privilage level [dec] failed by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_I

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-4-GD_DATAUNRELIABLE

4-Warning

Update to memory leak detector on free of 0x[hec] failed CLI output is unreliable\n

managed chunk malloc to store the range that is freed while memory leak detector is in progress failed. Hence memory leak detector will not be updated of this free and this can be reported as leak which is false.

mem

"Ignore the output of \"show memory debug leaks..\" if system is in low " "memory condition else perform a bug toolkit search on the web for " "existing bugs related to this error message if none found contact TAC " "for this problem providing \"show version\" and " "\"show memory statistics\" output."

SYS-3-GD_STACKERR

3-Error

Unknown stack. Process: [chars]\n

An internal error occurred when running the memory leak detector

mem

"Copy the error message exactly as it appears on the console or in the" " system log and look up the message in the Bug Toolkit at:" " http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl. If you are" " unable to resolve the issue using Bug Toolkit please issue a" " \"show tech\" and contact your technical support representative" " with the gathered information."

SYS-4-FREEMEMLOW

4-Warning

Free Memory has dropped below low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message is experiencing a low-memory condition. The amount of free memory available in the specified memory pool has dropped below the configured low-memory limit.

-

"No action is required"

SYS-5-FREEMEMRECOVER

5-Notice

Free Memory has recovered above low watermark\nPool: [chars] Free: %lu Threshold: %lu\n

The memory pool specified in the error message has recovered from a low-memory condition and the free memory in that pool is now above the configured low-memory limit.

-

"No action is required"

SYS-2-MALLOCFAIL

2-Critical

Memory allocation of [dec] bytes failed from [hex] alignment [dec] \n Pool: [chars] Free: [dec] Cause: [chars] \nAlternate Pool: [chars] Free: [dec] Cause: [chars] \n

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error may have exhausted or fragmented the router's memory.

mem-suspect

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representativeand provide the representative with the gathered information. " "Otherwise you may need to add more memory or reduce the number of " "features you are trying to support."

SYS-2-MUTEXLOCKFAIL

2-Critical

pthread_mutex_lock failed for [chars]

The thread failed in pthread_mutex_lock while trying to acquire a mutex.

mem-suspect

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-NOMEMORY

2-Critical

No memory available for [chars] [dec]

An operation could not be accomplished because of a low-memory condition. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

mem-suspect

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a configuration that has more memory."

SYS-3-CRITMEM

3-Error

[chars]

An attempt to allow or disallow a process from using memory that has been reserved for critical purposes has failed. The location of the failure is specified in the error message. This condition could possibly be caused by a software error.

mem-suspect

"Copy the error message and the traceback messages exactly as they appear " "on the colsole or in the system log contact your technical support " "representative and provide the representative with the gathered " "information."

SYS-2-GETBUFFFAIL

2-Critical

[chars] buffer allocation [dec] bytes failed from [hex]

-

-

-

SYS-6-NOBRIDGE

6-Information

Bridging software not present

Your system is not configured to be a bridge.

none

"Configure the bridging software."

SYS-3-SOCKUNKN

3-Error

Unknown socket protocol [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-HARIKARI

3-Error

Process [chars] top-level routine exited

An internal software error occurred

Determine the component from the process name displayed in the error message.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPID

2-Critical

Bad pid [dec] for tty [t-line]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-MGDTMRRUN

3-Error

TTY[t-line]: Managed Timers [chars] still running

One or more managed timers for a TTY that is deleted are still running.

-

LOG_STD_ACTION

SYS-0-USERLOG_EMERG

0-Emergency

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-1-USERLOG_ALERT

1-Alert

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-2-USERLOG_CRIT

2-Critical

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only. "

SYS-3-USERLOG_ERR

3-Error

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-4-USERLOG_WARNING

4-Warning

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-5-USERLOG_NOTICE

5-Notice

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-6-USERLOG_INFO

6-Information

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-7-USERLOG_DEBUG

7-Debug

Message from tty[t-line]user id: [chars]: [chars]

A user has used the 'send log' command to include a message on the configured logging destinations. Such messages can be used to help tag where user-initiated events occur during debugging. The severity level might have been changed by the user.

-

"This message is informational only."

SYS-3-MSGLOST

3-Error

[dec] messages lost because of queue overflow

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-REGEXP

4-Warning

[chars].

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-5-RESTART

5-Notice

System restarted --\n[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SCHEDULED_RELOAD

5-Notice

Reload requested for [chars]

A scheduled reload has been requested for the router.

none

"No action is required."

SYS-5-SCHEDULED_RELOAD_CANCELLED

5-Notice

Scheduled reload cancelled at [chars]

A scheduled reload that was requested for the router has been cancelled.

none

"No action is required."

SYS-5-RELOAD

5-Notice

Reload requested[chars]

A reload or restart was requested.

none

"This is a notification message only. No action is required."

SYS-5-SWITCHOVER

5-Notice

Switchover requested[chars]

A switchover was requested.

none

"This is a notification message only. No action is required."

SYS-4-RELOAD_ATTEMPT

4-Warning

Attempt via SNMP failed system shutdown not configured

SNMP cannot be used to reload the router unless this functionality has been previously configured. This message reports that an attempt to reload the router failed because SNMP reloads are not currently configured on the router.

none

"This is a notification message only. No action is required."

SYS-3-CFG_AT_RELOAD

3-Error

System reloading unable to complete startup configuration update

Startup configuration updation is already in progress and reload has been called either from interrupt level or with all interrupts disabled. Reload can not suspend to let startup configuration updation get completed. Startup configuration may get corrupted.

none

"This is a notification message only. No action is required."

SYS-4-DUAL_MESSAGE

4-Warning

SNMP system message request [dec] denied because of pending job

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-5-CONFIG

5-Notice

Configured from [chars]

The router's configuration was changed.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_I

5-Notice

Configured from [chars] by [chars]

The write of the system running configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_RESOLVE_FAILURE

4-Warning

System config parse from [chars] failed

The configuration file from the URL specified in the error message could not be read.

-

"Enter the <CmdBold>no service config<NoCmdBold> " "command to disable autoloading of configuration files " "OR investigate why the tftp load is failing."

SYS-5-CONFIG_NV

5-Notice

Nonvolatile storage configured from [chars]

The configuration was written successfully.

none

"This is a notification message only. No action is required."

SYS-5-CONFIG_NV_I

5-Notice

Nonvolatile storage configured from [chars] by [chars]

The write of the nonvolatile configuration failed.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-CONFIG_NV_DATA

3-Error

Variable [chars] not set properly in the routine [chars].

The write of the nonvolatile configuration failed because an internal variable was not set properly.

-

"If this messages occurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-CONFIG_NEWER

4-Warning

Configuration from version [dec].[dec] may not be correctly understood

The software detected that the configuration saved in memory was written by a newer version of software. There might be commands saved in memory that are not implemented by the older software version.

none

"Examine all the messages printed while the router was " "booting. For each message about an unknown command determine " "whether that feature is required. If so upgrade to a " "newer version of software that supports that feature."

SYS-4-CONFIG_NOLOCK

4-Warning

The configuration could not be locked

A software error occurred.

-

"Copy the error message exactly as it appears and report it " "to your technical support representative."

SYS-3-CONFIG_NO_PRIVATE

3-Error

No space remaining to save private config

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-4-CONFIG_NV_OVERRUN

4-Warning

Non config data present at the end of nvram is corrupted

The software detected that the configuration saved into nvram has overlaid a part of the nvram occupied by non config data files.Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_TRUNCATE

4-Warning

Truncated configuration to %ld bytes from %ld bytes

The software detected that the configuration saved into nvram has been truncated. There was not enough space to save the compressed configuration.

-

"Save the configuration to flash if the platform supports " " \"boot config\" command."

SYS-4-CONFIG_NV_NEED_OVERRUN

4-Warning

Non config data present at the end of nvram needs to be overwritten to fit the configuration into nvram

The software detected that the non config data files occupying the end of nvram need to be overwritten to fit the configuration. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

"Compress the configurtion and store or copy to flash as appropriate"

SYS-4-CONFIG_NV_NEED_TRUNCATE

4-Warning

Configuration needs to be truncated to fit into nvram

The software detected that the configuration is to be truncated to fit in the nvram. There was not enough space to save the compressed configuration

-

"Save the configuration to flash if the platform supports " "\"boot config nvbypass\" command."

SYS-4-NV_BLOCK_INITFAIL

4-Warning

Unable to initialize the geometry of nvram

The software detected that it failed to initialize the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload. This may happen when the entire nvram is packed with the configuration and the newer version of software which supports this feature could not find the minimum room in the nvram to initialize block file system.

-

"Reduce the configurations in the nvram atleast by 2K"

SYS-7-NV_BLOCK_INIT

7-Debug

Initialized the geometry of nvram

Initialized the nvram block geometry a part of the nvram to host non config data files. Typically these files are used by snmp to store and retrieve non config persistent data accross system reload.

-

""

SYS-4-NV_CHKSUM

4-Warning

An nvram checksum is already in progress

An interrupt service routine attempted to perform a checksum on the nvram contents and found the resource in use.

nvram

-

SYS-4-EXMALLOCFAIL

4-Warning

External memory allocation of [dec] bytes failed from EXMEM [dec]

The requested memory allocation is not available from the specified memory pool. The current system configuration network environment or possibly a software error might have exhausted or fragmented the router's memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMINIT

2-Critical

EXMEM [dec]: [chars]

The requested external memory allocator failed to be initialized. reasons are not clear.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMPARAM

2-Critical

Bad parameter [dec] when calling to the allocator utility

Illegal parameter is used when called to allocator. may represent data some corruption.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-EXMEMFREE

2-Critical

Free a non allocated ptr [hec] size [dec].

Trying to free a memory which not all of it marked as allocated.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CONFIG_DOWNFAIL

2-Critical

Generated configuration not backward compatible

The router has been configured to generate nonvolatile memory using the commands of an older software version. The current configuration of the router contains a command that cannot be saved using only the older command set.

none

"Allow the router to save the configuration using the command set of " "the current software version or remove the commands that cannot be " "saved using the older command set."

SYS-5-OUTSETUP

5-Notice

Configuration file [chars] accepted aborting setup

A configuration was accepted over the network so the setup session will be aborted.

none

"This is a notification message only. No action is required."

SYS-3-BADLINKTYPE

3-Error

* Unexpected linktype [dec]

* A software error occurred.

udp

* "Copy the error message exactly as it appears and report it to your " * "technical support representative."

SYS-2-SIGNUM

2-Critical

Process aborted on invalid signal signum = [dec].

An attempt was made to send an invalid signal to another process.

-

"If this message occurs more than once report this message " "to your technical support representative."

SYS-3-CPUHOG

3-Error

Task is running for [dec]msecs more than [dec]msecs [dec]/[dec]

The indicated process ran too long without relinquishing the processor. Each process should run for a small amount of time and then relinquish the CPU so that other processes can run. This problem can be caused by many things like traffic or system load hardware or operational configuration a configuration change initialization of many interfaces cards or ports for example a high momentary error rate a sustained abnormal

If this error occurs in conjunction with a TIMERHOG message \n\ report the two errors together and use the component obtained \n\ for the TIMERHOG message.

"If you suspect a software error copy the error message exactly as it " "appears on the colsole or in the system log contact your technical support" "representative and provide the representative with the gathered information."

SYS-2-WATCHDOG

2-Critical

Process aborted on watchdog timeout process = [chars].[chars]

The indicated process ran for too long without relinquishing control. The system killed it as a runaway process.

-

-

SYS-3-TIMERHOG

3-Error

Timer callback ran long PC = [hec].

The indicated callback routine ran for too long without relinquishing the processor.

Determine the component from the callback routine address displayed in\n\ the error message. Use Topic to search for a similar DDTS. If you \n\ find none write a DDTS for this problem.

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-6-STACKLOW

6-Information

Stack for [chars] [chars] running low [dec]/[dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-4-GREEDY_REGEXP

4-Warning

[chars] while processing the input regular expression. Aborting processing use alternate regular expression. Input regular expression: \[chars]\

Regular expression processing limitation: Certain regular expressions require huge stack space for processing or can lead to processing timeouts. We abort processing such regular expressions and print this message to avoid stack overflow/unexpected reload.

os

"The regular expression specified leads to stack overflow/processing " "timeout of the indicated process. Recommended to use a different " "regular expression."

SYS-1-CPURISINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr: [dec]%%/[dec]%%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped.

-

"Enter the <CmdBold>show processes CPU<NoCmdBold>" " command to determine the CPU hogging process" " that is causing this condition and if possible" " disable the activity that is causing the" " CPU hog condition so that CPU" " utilization is reduced."

SYS-1-CPUFALLINGTHRESHOLD

1-Alert

Threshold: [chars] CPU UtilizationTotal/Intr [dec]%%/[dec]%%.

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required."

SYS-2-INPUTQ

2-Critical

INPUTQ set but no IDB ptr=[hec]

This message is issued when an attempt is made to alter the input queue count for a packet that should not be counted.

-

-

SYS-6-BADSHAREINFO

6-Information

[chars] packet [hec] has a zero reference count freeing pid = [hec] \n\ freeing pc = [hec] [chars].

Provides additional information about original freer of packet.

-

-

SYS-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[hec]

A reference count is used to track the usage of many data structures. A function increments the count when it begins to use a structure and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be negative which means that the data structure will not be freed until the system is reloaded.

-

-

SYS-2-CFORKLEV

2-Critical

Process creation of [chars] failed at level [dec].

An internal software error occurred.

Determine the component from the process name displayed in the\n\ error message.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CFORKMEM

2-Critical

Process creation of [chars] failed no memory.

Insufficient memory was available to create a process either while trying to support additional features or due to a memory leak.

mem-suspect

"A memory leak may be the cause if the system has been running for a " "while without changing its configuration. If you suspect a leak then " "copy this message exactly as it appears and report it to your technical " "support representative. Otherwise ensure that more memory is available " "to support the additional features."

SYS-2-CFORKBADFUNCT

2-Critical

Can't create process with start address = [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPROCESS

3-Error

Bad process ID [dec] when [chars] process table

An internal software error occurred.

os-scheduler

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INSCHED

2-Critical

[chars] within scheduler

-

Determine the component from the stack trace displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem.

-

SYS-2-NOTIOSTASK

2-Critical

[chars] from outside IOS task context

An IOS reschedule request was made from code that is not running in the context of an IOS task -- from an interrupt handler the scheduler itself or a service pthread within the IOS process.

Determine the component from the stack trace displayed in the\n\ error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-INTSCHED

2-Critical

'[chars]' at level [dec]

The scheduler was entered from an interrupt service routine ISR.

Determine the component from the stack trace and process name displayed in the error message. Then use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component.

-

SYS-3-PROCSEMFAIL

3-Error

Process semaphore creation for preemptive processes failed.

Creation of process function semaphore to protect the critical section of process create routine failed. The semaphore creation can fail if there isnt enough chunk memory to create the event structure.

os

-

SYS-2-NOBLOCK

2-Critical

[chars] with blocking disabled.

A process aattempted to relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

-

SYS-2-BLOCKHUNG

2-Critical

Task hung with blocking disabled value = 0x[hec].

The indicated process has exceeded the time limit for which it may relinquish control with blocking disabled.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the scheduler.

"This message may be a result of high loads. If it recurs " "copy the text exactly as it appears and report it along " "with the associated stack trace to your technical support " "representative."

SYS-2-NOTDEAD

2-Critical

Killing process [chars] pid [dec] again

An internal software error occurred.

os-scheduler

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOPROCESS

2-Critical

No such process [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-IMMORTAL

2-Critical

Attempt to shut down management process [dec] [chars].

An attempt was made to shut down the specified management process. Management processes must not be shut down as long as the\n\ router remains up.

Determine the component from the stack trace displayed in the error message. Use Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. Choose the DDTS component associated with the routine that called the process_kill.

-

SYS-2-SIGPENDING

2-Critical

Multiple Signals are sent to a process [dec]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADSTACK

2-Critical

Process [chars] has trashed stack old size [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-6-MTRACE

6-Information

[chars]: addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC

This is an auxiliary message to several memory-related messages. It provides the address of the memory block and the calling program counter for the last eight blocks allocated and for the last eight blocks freed.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of a previously printed error message."

SYS-6-BLKINFO

6-Information

[chars]blk [hec] words [dec] alloc [hec] [chars] dealloc [hec] rfcnt [hec]

This is an auxiliary message to several memory-related messages. It provides a formatted display of some of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-MEMDUMP

6-Information

[hex]: [hex] [hex] [hex] [hex]

This is an auxiliary message to several memory-related messages. It provides a raw display of the information in the header of a corrupted data block.

Include this error message in the DDTS that was written for\n\ the previously printed error message.

"This message provides additional information only. Copy the error " "message exactly as it appears and report it to your technical support " "representative as part of the previously printed error message."

SYS-6-PROCINFO

6-Information

Process [chars] just finished executing

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

-

"Copy this messages exactly as it appears and report it along with " "the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your " "technical support representative."

SYS-6-TESTINFO

6-Information

Scheduler test [hex] for [chars] just executed

This message is an auxiliary to the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages. It identifies the process or process fragment that was executing when the error occurred.

Determine the component from the address of the scheduler test routine\n\ displayed in the error message.\n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem.

"Copy this message exactly as it appears and report it along with the " "SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical " "support representative."

SYS-3-BADBLOCK

3-Error

Bad block pointer [hec]

A block of memory at the indicated location is corrupt. An internal check of memory block pointers indicates an inconsistency.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to auotmatically reload then the router will " "need to reloaded manually."

SYS-3-BADMAGIC

3-Error

Corrupt block at [hec] magic %08x

The free memory pool is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADREFCOUNT

3-Error

Bad reference count at [hec] refcount [hec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-3-OVERRUN

3-Error

Block overrun at [hec] red zone %08x

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-FREEBAD

2-Critical

Attempted to free memory at [hec] not part of buffer pool

An attempt was made to free memory but the request could not be completed due to an invalid memory data structure

-

-

SYS-2-FREEFREE

2-Critical

Attempted to free unassigned memory at %lx alloc %lx dealloc %lx

An attempt was made to free memory at the indicated location. The memory could not be freed because it was not allocated.

-

-

SYS-3-INVMEMINT

3-Error

Invalid memory action [chars] at interrupt level

This message indicates that a memory allocation or deallocation was attempted from an interrupt handler.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-INVMEMPID

3-Error

Invalid pid [dec] in block: [hec]

There has been attempt to allocate memory on behalf of an invalid process.

mem

-

SYS-3-MEMSEMFAIL

3-Error

Mempool semaphore creation failed for [chars]

This message indicates that the semaphore creation for the specified mempool failed.

-

-

SYS-3-INUSEFREE

3-Error

Block [hec] on free list [dec] in use

A memory management function attempted to allocate the indicated block from a list of free blocks. However the block was found to be already in use.

-

-

SYS-3-NZREFCNT

3-Error

Block [hec] on free list [dec] with refcount [dec]

A block of memory in the free pool is actually in use. The message indicates the number of processes using the memory block.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-WRONGFREELIST

3-Error

Block [hec] size [dec] on wrong free list [dec] [dec]

A freed buffer was placed on the wrong list of free buffers.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEMAGIC

3-Error

Corrupt free block at [hec] magic %08x

A block of memory at the indicated location is corrupt. An inconsistency was detected while checking the free memory area.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-BADPTRVAL

3-Error

Bad pointer value [chars] = [hec] in function [chars]

Corrupted pointer value is encountered.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADFREEPTRS

3-Error

Bad [chars] pointer [hec] at [hec] [chars] = [hec]

A pointer in the block header at the indicated location is corrupt. An inconsistensy was detected in the free memory pool.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-GETBUF

2-Critical

Bad getbuffer bytes= [dec]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

-

SYS-2-INPUT_GETBUF

2-Critical

Bad getbuffer bytes= [dec] for interface= [chars]

The software requested a buffer that is larger than the largest configured buffer size or it requested a negative-sized buffer.

Determine the component from the stack trace and process name displayed in the error message. \n\nUse Topic to search for a similar DDTS. If you find none submit a DDTS for this problem. If the stack trace indicates that the buffer code was called from an interrupt handler use the interrupt handler to determine the DDTS component. Otherwise use the process name to determine the DDTS component.

LOG_STD_ACTION

SYS-2-INLIST

2-Critical

Buffer in list ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-INLIST1

2-Critical

Buffer in list ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SHARED1

2-Critical

Attempt to return buffer with sharecount [dec] ptr= [hec] caller= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-BADPOOL

2-Critical

Attempt to use buffer with corrupt pool pointer ptr= [hec] pool= [hec]

An memory management function attempted an operation that could not be performed due to invalid memory pool descriptors.

-

-

SYS-2-BADPOOLMAGIC

2-Critical

Attempt to use pool pointer with corrupt header pool= [hec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-WRONGPOOL

2-Critical

Buffer [hec] found in pool [hec] should be in pool [hec]

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-2-BADBUFFER

2-Critical

Attempt to use [chars] buffer as [chars] ptr= [hec] pool= [hec]

A hardware or software error occurred. An inconsistency was encountered while processing a packet buffer.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information."

SYS-2-QCOUNT

2-Critical

Bad [chars] [hec] count [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-NOTQ

2-Critical

[chars] didn't find [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-LINKED

2-Critical

Bad [chars] of [hec] in queue [hec]

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-SELFLINKED

2-Critical

Buffer [hec] linked to itself in free pool [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-2-ALREADYFREE

2-Critical

Buffer [hec] already in free pool [chars]

A block of memory at the indicated location is corrupt and/or has been erroneously freed twice.

os

"If this message recurs copy it exactly as it appears and the output " "of 'show buffer address <number>' for the given address as well as " "'show buffer pool <name> dump' for the given pool. Report it to your " "technical support representative."

SYS-2-LOWMEMPROC

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available processor memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak copy the message exactly as it appears and " "report it to your technical support representative. Otherwise you may " "need to add memory or reduce the number of features you are trying to " "support."

SYS-2-LOWMEMIO

2-Critical

Low-memory debug exception limit=[dec] free=[dec]

The router is configured to crash when total available IO memory drops below a specified threshold. That threshold has been reached. This may have occurred due to a memory leak or from supporting additional features.

mem

"If you suspect a memory leak " "copy the message exactly as it appears and " "report it to your technical support representative. " "Otherwise you may need to add memory " "or reduce the number of features you are trying to " "support."

SYS-2-NOMEMFRGPROC

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous processor memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-NOMEMFRGIO

2-Critical

Memory fragmentation check debug exception fragment size [dec]

The router is configured to crash when the largest available contiguous IO memory block drops below a specified threshold. That threshold has been reached. This may have occurred due to excessive memory thrashing or from supporting additional features.

mem

"If you suspect memory thrashing " "copy the message exactly as it appears " "and report it to your technical support representative. Otherwise " "you may need to add memory or reduce the number of features you are " "trying to support."

SYS-2-SPEC

2-Critical

Trying to set unknown special character [dec] to [dec]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-ABRUPTTERM

3-Error

Abrupt termination of tty session for [chars] [t-line]

An internal software error occurred.

os

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-3-BADDISP

3-Error

Bad disposal code [hec] in [chars]

An invalid status code has been passed to a buffer deletion routine. The buffer will be correctly returned to the free pool but will not be correctly counted in the per-protocol statistics.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NULLIDB

3-Error

Null IDB in [chars]

An internal software error occurred.

-

"If this messages recurs copy it exactly as it appears and report " "it to your technical support representative."

SYS-1-OVERTEMP

1-Alert

System detected OVERTEMPERATURE condition.\n Please resolve cooling problem immediately!\n

The environmental monitor detected a high-temperature condition.

none

"Make sure that the room temperature is not too high and that air flow " "to the card is not blocked. If this condition persists the " "environmental monitor might shut down the system. Call your technical " "support representative for assistance if necessary."

SYS-3-BADPARAM

3-Error

Function [chars]: value [hex] passed in parameter [chars]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADRESID

3-Error

Clock hardware returned bad residual [dec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-BADPRINT

3-Error

Process has no associated tty in [chars].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-INTPRINT

3-Error

Illegal printing attempt from interrupt level.

An internal software error occurred.

Determine the component from the stack trace and process name\n\ displayed in the error message. \n\ Use Topic to search for a similar DDTS. If you find none write\n\ a DDTS for this problem. If the stack trace indicates that the\n\ buffer code was called from an interrupt handler use the interrupt\n\ handler to determine the DDTS component. Otherwise use the process\n\ name to determine the DDTS component.

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-OVFPRINT

3-Error

Overflow in [chars] chars [dec] buffer size [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-NOELEMENT

3-Error

[chars]:Ran out of buffer elements for enqueue

The process was unable to enqueue data as it ran out of buffer elements.

-

"Copy the error message exactly as it appears also get the " "output of show buffers and report it to your technical support " "representative."

SYS-6-CLOCKUPDATE

6-Information

System clock has been updated from [chars] to [chars] configured from [chars] by [chars].

This message indicates that the system clock has been modified.

-

"This is informational message."

SYS-5-TABLEERR

5-Notice

[chars] table [chars] damaged: [chars].

An internal table entry became corrupt.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-3-BADTREEPARAM

3-Error

Bad parameter for [chars] passed to tree library function.

This message indicates that a pointer passed to a tree library function is invalid.

-

LOG_STD_SH_TECH_ACTION

SYS-2-BADLIST

2-Critical

Regular expression access check with bad list [dec]

This message indicates that a pointer to an access list is invalid.

-

"The event that caused this message to be issued should not " "have occured. It can mean that one or more data structures " "have been overwritten. If this message recurs and you decide " "to report it to your technical representative you should " "copy the text of the message exactly as it appears and " "include the associated stack trace." "\n\n Since access list corruption may have occurred " "a technical representative should verify that access " "lists are functioning corectly."

SYS-2-SNMP0IDX

2-Critical

Attempt to [chars] snmpidb with if_index of 0

A software error occurred.

-

"Copy the message exactly as it appears and report it your technical " "support representative."

SYS-4-SNMP_WRITENET

4-Warning

SNMP WriteNet request. Writing current configuration to [inet]

SNMP is writing the current configuration to a network host.

none

"These are notification messages only. No action is required."

SYS-4-SNMP_HOSTCONFIGSET

4-Warning

SNMP hostConfigSet request. Loading configuration from [inet]

SNMP is reading the host configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-SNMP_NETCONFIGSET

4-Warning

SNMP netConfigSet request. Loading configuration from [inet].

SNMP is reading the network configuration from a network host.

none

"This is a notification message only. No action is required."

SYS-4-INVALID_IMAGE

4-Warning

Running invalid image for platform!

The software image being run is for a different hardware architecture. This problem can occur on a Cisco 1003 Cisco 1004 or Cisco 1005. The Cisco 1003 and Cisco 1004 use a different image from the Cisco 1005.

none

"Install the correct software image."

SYS-2-CHUNKBOUNDS

2-Critical

Could not find the sibling to allocate memory from. Chunk [chars] total free [dec] inuse [dec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKBOUNDSIB

2-Critical

Error noticed in the sibling of the chunk [chars] Chunk index : [dec] Chunk real max : [dec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKFREE

2-Critical

Attempted to free nonchunk memory chunk [hec] data [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKSIBLINGDEST

2-Critical

Attempted to destroy a sibling chunk [hec] [chars].

-

-

-

SYS-2-CHUNKSIBLINGS

2-Critical

Attempted to destroy chunk with siblings chunk [hec].

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKPARTIAL

2-Critical

Attempted to destroy partially full chunk chunk 0x[hec] chunk name: \[chars]\.

A software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CHUNKBADMAGIC

2-Critical

Bad magic number in chunk header chunk [hec] data [hec] chunkmagic [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-6-INVALID_BOOTTIME

6-Information

Time since last reboot not available

This is an informational message for the user. The time taken for the router to come up after OIR is not available.

-

"No action required."

SYS-6-BOOTTIME

6-Information

Time taken to reboot after reload = %-4d seconds

This is an informational message for the user. This provides the time taken for the router to come up after reload or crash. The time is actually the difference between the last crash and a successive boot. If autoboot was not set and router is in rommon for a long time then the reload time shown could be large.

-

"No action required."

SYS-2-CHUNKBADREFCOUNT

2-Critical

Bad chunk reference count chunk [hec] data [hec] refcount [hec] alloc pc [hec].

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOMEMORY

2-Critical

* Could not allocate chunks for [chars]. No memory

* A software error occurred.

-

* "Copy the error message exactly as it appears and report it to " * "your technical support representative."

SYS-2-CHUNKEXPANDFAIL

2-Critical

Could not expand chunk pool for [chars]. No memory available

There is not enough processor memory left to grow this chunk pool.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADFREEMAGIC

2-Critical

Bad free magic number in chunk header chunk [hec] data [hec] chunk_freemagic [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-2-CHUNKNOROOT

2-Critical

Root chunk need to be specified for [hec]

A software error occurred.

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINVALIDHDR

2-Critical

Invalid chunk header type [dec] for chunk [hec] data [hec]

An inconsistency was detected while managing the chunk memory pool. The probability that this is a software error is close to 100 percent but there could be a hardware problem with memory.

-

"Copy the error message exactly as it appears on the console " "or in the system log contact your Cisco technical support representative " "and provide the representative with the gathered information. " "Save any crashinfo or crashdump files. If the router has crashed and " "was not configured to automatically reload the router will " "need to be reloaded manually."

SYS-3-CRASHINFOINITFAIL

3-Error

Crashinfo subsys initialization did not add registry \n\ crashinfo_get_default_file_name.\n

In order to figure out the device which the crashinfo writes to the crashinfo subsys has to add the registry crashinfo_get_default_file_name.

-

"Use Topic to search for a similar DDTS. If you find none write " "a DDTS for this problem. This SHOULD never happen - it is an " "indication of a bug elsewhere in the code."

SYS-2-CHUNKBADPOOLSIZE

2-Critical

Bad poolsize returned by the system : [dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKINCONSIS

2-Critical

Inconsistant counters for chunk : [chars] total free [dec]/[dec] total sibs [dec]/[dec] total alloc [dec]/[dec]

System returns a non-optimal pool size. Need to change pool sizes

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-CHUNKBADELESIZE

2-Critical

Chunk element size is more than 64k for [chars]

Chunk manager cannot function properly with big chunk elements

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-2-NULLCHUNK

2-Critical

Memory requested from Null Chunk

Chunk manager cannot allocate memory from NULL chunks

-

"Copy the error message exactly as it appears and report it to " "your technical support representative."

SYS-4-CHUNKSIBLINGSEXCEED

4-Warning

Number of siblings in a chunk has gone above the threshold. Threshold:[dec] Sibling-Count:[dec] Chunk:0x[hec] Name:[chars]

Number of siblings in a chunk with no header has gone above the default/configured threshold configured using <cmdBold>memory chunk siblings threshold<nocmdBold> <cmdArgs>count<nocmdArgs>

-

LOG_STD_SH_TECH_ACTION

SYS-1-CCA_SYS_ERR

1-Alert

CCA Detected System Error code = [dec]

CCA has detected a severe system software error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-2-CCA_INT_ERR

2-Critical

CCA Detected Logic Error code = [dec]

CCA has detected a severe internal logic error. This condition is usually caused by one of the components using CCA or by the interaction among components using CCA.

os

LOG_STD_ACTION

SYS-3-TIMERNEG

3-Error

Cannot start timer [hex] with negative offset [dec].

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-MGDTIMER

3-Error

[chars][chars] timer = [hec].

This message indicates an error in a system timer. The problem can be caused either by software or by hardware.

-

-

SYS-3-DMPMEM

3-Error

%08x: %08x %08x %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-BOOT_MESSAGES

6-Information

Messages above this line are from the boot loader.\n

At least one informational or error message was printed by the boot loader.

-

"If the system image was loaded no action is recommended. If the " "system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-2-EXCEPTIONDUMP

2-Critical

System Crashed Writing Core....

The system has crashed because of an exception A core is being generated

-

LOG_STD_ACTION

SYS-3-LOGGER_FLUSHING

3-Error

System pausing to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system is paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_FLUSHED

3-Error

System was paused for %TE to ensure console debugging output.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. In order to guarantee that they can be seen the rest of the system was paused until the console output catches up. This can break time-critical behavior such as maintaining an ISDN link.

-

"Consider using conditional debugging turning off console logging " "or using the \"no logging console guaranteed\" command or turning " "off link-state messages for some interfaces"

SYS-3-LOGGER_DROPPED

3-Error

System dropped [dec] console debug messages.\n

Debugging or informational messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages.

-

"Consider using conditional debugging or turning off console logging."

SYS-3-LOGGER_COUNT_STOP_CHUNK

3-Error

System cannot release chunk memory.\n

The system was not able to destroy a previously allocated chunk of memory.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-CHUNK_NO_EXMEM

3-Error

No handler to [chars] external memory.

An attempt was made to allocate or free a chunk of external memory but no handler for managing external memory was registered.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-6-READ_BOOTFILE_FAIL

6-Information

[chars] [chars].\n

A configured boot system command failed.

-

"If a system image was eventually loaded no action is recommended. If " "the system image did not load as configured send a log file and " "configuration information to your technical support representative."

SYS-3-URLWRITEFAIL

3-Error

redirection url write failed '[chars]'

Redirection of output to URL failed.

-

"Check for free space on destination URL and retry."

SYS-6-READ_BOOTFILE_SKIP

6-Information

boot system [chars] command is skipped\n

A configured boot system command is skipped. Either the system experienced a crash while loading this image in the last attempt or the filename is not properly specified. Subsequent boot system commands will be tried

-

"Replace the failed boot system image with a good one. There could be " "various reasons that this specified image failed for example the image " "might be with a bad checksum."

SYS-6-USING_RESERVE_MEMORY

6-Information

Reserve memory is being used

The reserved memory is being used by the console

-

"The system is low in memory. The reserved memory will be " "used only by the console process. Please take a techsupport " "so that the reason for low memory can be found"

SYS-6-RESERVE_MEMORY_CREATED

6-Information

Reserve memory is being created

A portion of memory is reserved exclusively for console

-

"The console access is made available even in low memory " "condition. User can collect the details like tech-support " "for further diagnosis"

SYS-3-BAD_RESET

3-Error

Questionable reset of process [dec] on tty[t-line]\n

A process was reset without giving it a chance to clean itself up.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-DUP_TIMER

3-Error

Same tty[t-line] in linewatch_timers type [dec]

A tty appeared twice in a timer list where it should have only appeared once.

exec

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-LINEPROCDEAD

2-Critical

Killing process [chars] associated with line [dec]

A process associated with a tty line was killed by another process. The line may go dead

exec

"If this messages recurs copy it exactly as it appears " "and report it to your technical support representative."

SYS-3-HTIMER_EXPAND

3-Error

timer heap at 0x[hec] needed to expand but hasn't

A timer heap should have expanded but has not

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_INIT

3-Error

heap timer at 0x[hec] has not been initialized

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-3-HTIMER_STATE

3-Error

heap timer at 0x[hec] in state [dec]

A heap timer has not been initialized

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-MUNMAP

2-Critical

Could not return memory Neutrino via munmap at %lx size [dec] errno [dec]

Failued to unmap memory memory at the indicated location. The memory could not be unmapped because it was allocated via mmap.

-

-

SYS-2-MMAP

2-Critical

mmap failed for size [dec] bytes Caller PC 0x[hec] errno [dec]

Failed to allocate memory for the requested size. The memory could not be mapped because there is no memory.

-

-

SYS-3-CERF_RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a cache error

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-CERF_ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-2-PAK_SUBBLOCK_SETSIZE

2-Critical

[dec]

This message indicates an error in startup code to register a pak subblock size. An attempt was made to register a size after the subblock chunk pool had been initialized. This problem is caused by software initialization order.

-

-

SYS-3-RGCREATEFAIL

3-Error

Resource group creation failed\nCause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGADDFAIL

3-Error

Couldn't add process process pid [dec] to resource group [hec]\n Cause: [chars]

An attempt to create a resource group failed at the indicated location

-

-

SYS-3-RGDELEFAIL

3-Error

Couldn't delete process process pid [dec] from resource group\n \nCause: [chars]

An attempt to remove a process from a resource group failed at the indicated location

-

-

SYS-3-RGDESTFAIL

3-Error

Couldn't destroy resource group [hec]\nCause: [chars]

An attempt to destroy a resource group failed at the indicated location

-

-

SYS-3-RGOPFAIL

3-Error

Requested memory thresholding operation on resource group failed\n Resource Group handle: [hec] Cause: [chars]

The message indicates that an request to Set/Get memory thresholding data or enable/disable thresholding failed in the indicated location

The component that issued the request

-

SYS-3-RGMEMEXCEED

3-Error

\nLimit Exceeded: [chars] Holding: %lu Requested:%lu bytes

A resource group has requested for more memory than the configured limit at the indicated location

The component to which the offending resource group belongs.

-

SYS-2-PAK_SUBBLOCK_BADSIZE

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. The requested size is larger than the maximum registered subblock size.

-

-

SYS-2-PAK_SUBBLOCK_ALREADY

2-Critical

[dec]

This message indicates an error in attempting to allocate a pak subblock. A subblock was already associated with the packet.

-

-

SYS-3-IMAGE_TOO_BIG

3-Error

'[chars]' is too large for available memory [dec] bytes.

The allocated memory for the image is too small to hold the image file.

-

"Increase the amount of memory available in the router by booting " "with a smaller image not enabling non-essential sub-systems " "or upgrading the installed memory. Call your technical " "support representative for assistance."

SYS-2-BAD_BM_ARG

2-Critical

Invalid BM index boolean used as argument [dec]

An illegal boolean manager index argument was referenced

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-MAX_IDB_BM_EXCEEDED

2-Critical

BM bit allocation limit exceeded

The BM has exhausted all of the bits available for allocation

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-BAD_BM_NAME

2-Critical

Invalid BM name

An illegal name string was registered with the BM

idb

"Copy the error message exactly as it appears and report it to" " your technical support representative."

SYS-2-ASSERTION_FAILED

2-Critical

Assertion failed: \[chars]\

An internal state consistency check failed. Correct operation cannot be guaranteed and the system has been halted.

-

LOG_STD_ACTION

SYS-6-STARTUP_CONFIG_IGNORED

6-Information

System startup configuration is ignored based on the configuration register setting.

The configuration register was set to ignore the system startup configuration.

-

"If the system should ignore the startup configuration no action " "is required. If the system should boot with the startup configuration " "saved in the NVRAM change the configuration register value."

SYS-3-URLREADFAIL

3-Error

cannot open file for reading '[chars]'

The URL for the cannot be opened for reading.

-

"Check for proper Uniform Resource Locator syntax and for read " "permission and retry."

SYS-3-TCLSETFAIL

3-Error

cannot set TCL interpreter variable '[chars]' to '[chars]' : '[chars]'

The value could not be passed to the TCL interpreter

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

SYS-7-ESMSHUTDOWN

7-Debug

ESM shutdown

The Embedded Syslog Manager has been shut down

-

LOG_STD_NO_ACTION

SYS-6-LOGGINGHOST_STARTSTOP

6-Information

Logging to host [chars][chars][chars][chars]

Syslog logging to specified server or hostvrf has started or stopped

os-logging

LOG_STD_NO_ACTION

SYS-4-CPURESRISING

4-Warning

[chars][chars] is seeing [chars] cpu util [dec]%% at [chars] level more than the configured [chars] limit [dec] %%

The system is experiencing high CPU usage possibly from a process that is using too much CPU. This condition demands immediate attention or packets or calls may be dropped. CPURESRISING notifications should be matched with the corresponding CPURESFALLING/CPURESUNAPPLY notification.

-

"No action is required"

SYS-6-CPURESFALLING

6-Information

[chars][chars] is no longer seeing [chars] high cpu at [chars] level for the configured [chars] limit [dec]%% current value [dec]%%

CPU usage has returned to normal after crossing over from a threshold of high usage. Any process that was disabled during the period of high CPU use can now be enabled.

-

"No action is required"

SYS-6-CPURESUNAPPLY

6-Information

[chars][chars] is no longer monitoring [chars] cpu at [chars] level for the configured [chars] limit.

CPU usage is no loger monitored for the configured threshold level mentioned in the error message The corresponding policy is revoked.

-

"No action is required"

SYS-3-BADLIST_DESTROY

3-Error

Removed a non-empty list[hec] name: [chars] having %lu elements

A non-empty list should not be destroyed. If it happens there is a possibility that all elements enqueued into the list will never be deallocated. This message reports that an non-empty list got destroyed.

Determine the component from the stack trace and process name displayed in the error message.

LOG_STD_ACTION

SYS-2-SYSMEMINFO

2-Critical

System Memory: %luK total %luK used %luK free

This is an auxiliary message to several memory-related messages. It\n\ provides system memory information usage.

-

"This message provides additional information only. Copy the error \n\ message exactly as it appears and report it to your technical support \n\ representative as part of a previously printed error message."

SYS-6-LOGGING_BUGINF

6-Information

Logging of buginf debugs was [chars]

All calls to debugging have been disabled in Cisco IOS software as a result the user entering the <CmdBold>no logging buginf<NoCmdBold> command. This command is used to avoid a situation where a large amount of debugging calls might overload the processor CPU hog condition. This

os-logging

"This is an informational message only. No action is required."

SYS-5-FIFOBUS_ERR

5-Notice

Flow-control threshold on module [dec] has exceeded the default value. Threshold will be set to lower value

The FIFO threshold values are monitored for flow-control. When the threshold value exceeds the default the value is set to new lower value

Cat6000-env

LOG_STD_NO_ACTION

SYS-5-PRIV_AUTH_PASS

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_AUTH_FAIL

5-Notice

Authentication to Privilage level [dec] failed by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SYS-5-PRIV_I

5-Notice

Privilege level set to [dec] by[chars][chars]

-

os-logging

"This is a notification message only. No action is required. " "To disable this particular logging feature issue the " "<CmdBold>no logging userinfo<NoCmdBold> command from the " "global configuration mode."

SMF-4-INVALID_ACTION

4-Warning

failed to create SMF entry for [enet] on [chars] with result %08x

An internal software error occurred.

-

LOG_STD_ACTION

SMRP-6-PORTUP

6-Information

[chars]: SMRP port up - [chars]

An SMRP port has come up.

-

"Notification message only. No action required."

SMRP-5-PORTDOWN

5-Notice

[chars]: SMRP port down - [chars]

An SMRP port is down and is no longer operational.

-

"Notification message only. No action required."

SMRP-6-NEIGHBORUP

6-Information

[chars]: SMRP neighbor up - [chars]

A neighboring SMRP router has appeared.

-

"Notification message only. No action required."

SMRP-5-NEIGHBORDOWN

5-Notice

[chars]: SMRP neighbor down - [chars]

SMRP cannot be started on an interface that is running\n\ pre-FDDITalk.

-

"Use FDDITalk on the FDDI ring if possible."

SMRP-2-ASSERTFAILED

2-Critical

SMRP assertion failed: [chars]

The software detected an inconsistency. This is considered a serious\n\ error. The router attempts to continue but SMRP processing may be\n\ impaired.

-

"Copy the error message exactly as it appears noting any SMRP problems\n\ that you are experiencing and report it to your technical support\n\ representative."

SMRP-7-DEBUGMSG

7-Debug

SMRP Debug: [chars]

This message is generated by some debug commands to provide additional\n\ information about conditions in SMRP.

-

"If you are experiencing problems in SMRP these messages should be\n\ provided along with any other information in a report to your\n\ technical support representative."

SNMP-3-TRAPINTR

3-Error

Attempt to generate SNMP trap from interrupt level

During the processing of an interrupt the code attempted to\n\ generate an SNMP trap. This is not allowed.

Determine the component from the stack trace which indicates\n\ which subsystem is attempting to generate a trap. Search for\n\ similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP-3-TRAPBLOCK

3-Error

Attempt to generate SNMP trap from a process with blocking disabled

During processing a process with blocking disabled attempted to\n\ generate an SNMP trap which would block. This is not allowed.

Determine the component from the stack trace which indicates\n\ which subsystem is attempting to generate a trap. Search for\n\ similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP-4-TRAPDROP

4-Warning

[chars]

An attempt was made to generate an SNMP trap but the trap\n\ could not be sent because of the reason given in this message.\n\ Most likely this message means that the SNMP traps process is\n\ not running.

snmp

"Copy the error message exactly as it appears and report it\n\ to your technical support representative. Use the <bold>show process<nobold>\n\ command to determine whether the SNMP traps process is running.\n\ If it is not running reload the system. If after reloading\n\ the SNMP traps process is still not running there may not be\n\ enough memory for it to run."

SNMP-3-BADVALUE

3-Error

Maximum number of index supported is 20

An SNMP trap contains some number of MIB objects and the size\n\ of the instance identifier for these objects is restricted. This\n\ message indicates that an attempt was made to generate an SNMP\n\ trap containing a MIB object whose size exceeded this limit.

snmp

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP-3-BADOID

3-Error

Attempt to generate an invalid object identifier

A valid object identifier must contain at least two subidentifiers.\n\ An attempt was made to generate an object identifier whose size\n\ was less than two.

Determine the component from the stack trace which indicates\n\ which subsystem is attempting to generate invalid object\n\ identifiers. Search for similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP-3-CPUHOG

3-Error

Processing [chars] of [chars]

SNMP took too much time processing a request.

Determine the component from the debug output which indicates\n\ which subsystem is processing a request. Search for similiar DDTS\n\ reports and open a DDTS.

"If feasible use the <bold>debug snmp packet<nobold> command to determine the\n\ contents of the SNMP request that is causing the message. Copy the\n\ error message exactly as it appears and report it along with any\n\ debug output to your technical support representative."

SNMP-4-HIGHCPU

4-Warning

Process exceeds [dec]ms threshold [dec]ms IOS quantum for [chars] of [chars]--result [chars]

SNMP took more than the warning threshold processing a var-binding.

Determine the component from the debug output which indicates\n\ which subsystem is processing a request. Search for similiar DDTS\n\ reports and/or based on the impact of the processing time \n\ determine if this is a bug.

"If feasible use the <bold>debug snmp packet<nobold> command to determine the\n\ contents of the SNMP request that is causing the message. Copy the\n\ error message exactly as it appears and report it along with any\n\ debug output to your technical support representative. Some MIB \n\ objects require a relatively large amount of time to process. \n\ MIB objects in the multi-variable-binding are processed one by one. \n\ If possible MIB objects appearing in this message should NOT be \n\ retrieved using multi-variable-binding SNMP PDUs."

SNMP-3-SYNCFAIL

3-Error

SNMP MIB Sync Failure: [chars]

One of the SNMP MIB Sync to standby failed.

Determine the mib component from the stack trace which indicates\n\ which MIB sync failure is generating this message.\n\ Search for similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP-3-DYNSYNCFAIL

3-Error

Snmp Dynamic Sync Failed for [chars] = [chars]

One of the SNMP MIB Dynamic Syncsync of Snmp SET to standby failed.

Determine the component from the OIDs printed as part of the message\n\ for which dynamic sync has failed.\n\ Search for similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP-4-NOFLASH

4-Warning

Reading snmpEngineBoots from flash failed

An attempt to read the snmpEngineBoots file from flash failed.\n\ Most likely this means that the flash card does not exist on\n\ the router. This message should appear only when the router is\n\ reloaded.

snmp

"\n\ Check if installing a flash card makes the message go away.\n\ If a flash card exists already it may be full. Try erasing\n\ flash and reloading the router. If after these steps the problem\n\ persists copy the error message exactly as it appears and report\n\ it to your technical support representative."

SNMP-4-NOENGINEID

4-Warning

Remote snmpEngineID for [inet] not found when creating user: [chars]

-

snmp

"\n\ Configure the remote snmpEngineID and reconfigure the user.\n\ If the problem persists copy the error message exactly as it\n\ appears and report it to your technical support representative."

SNMP-4-NOENGINEIDV6

4-Warning

Remote snmpEngineID for %P not found when creating user: [chars]

-

snmp

"Configure the remote snmpEngineID and reconfigure the user.\n\ If the problem persists copy the error message exactly as it\n\ appears and report it to your technical support representative."

SNMP-5-COLDSTART

5-Notice

SNMP agent on host [chars] is undergoing a cold start

The snmp server underwent a coldstart.

none

"Notification message only. No action required."

SNMP-5-WARMSTART

5-Notice

SNMP agent on host [chars] is undergoing a warm start

The snmp server underwent a warmstart.

none

"Notification message only. No action required."

SNMP-3-AUTHFAIL

3-Error

Authentication failure for SNMP req from host [inet]

An SNMP request was sent to this host which was not properly\n\ authenticated.

none

"Make sure that the community/user name used in the SNMP req\n\ has been configured on the router."

SNMP-5-LINK_DOWN

5-Notice

LinkDown:Interface [chars] changed state to down

The state of the Interface is changed to down.

none

""

SNMP-5-LINK_UP

5-Notice

LinkUp:Interface [chars] changed state to up

SNMP agent generated view length greater than that allowed by definition so the view name was truncated to fit the defined maximum view name length.

snmp

"Make sure your trap group and view names are setup appropriately. " "You can override with 'snmp-server group' command. Notify Cisco " "that this needs to be fixed."

SNMP-3-AUTHFAILIPV6

3-Error

Authentication failure for SNMP request from host %P

An SNMP request was sent by this host which was not properly\n\ authenticated.

none

"Make sure that the community/user name used in the SNMP req\n\ has been configured on the router."

SNMP-5-MODULETRAP

5-Notice

Module [dec] [[chars]] Trap

This message shows the SNMP agent sends out the Module Up/Down Traps to the engine ID of the remote agent or SNMP manager because the corresponding module is up/down.

snmp

""

SNMP-5-CHASSISALARM

5-Notice

Chassis Alarm Trap: tmpAlarm[chars] minorAlarm[chars] and/or majorAlarm[chars]

This message shows the SNMP agent sends out the Chassis Alarm On/Off Traps to the engine ID of the remote agent or SNMP manager because the corresponding chassis alarm is on/off.

snmp

""

SNMP-3-BADIFINDEXTABLE

3-Error

The file nvram:ifIndex-table is corrupt.

The file is not in the expected format.

snmp

"If possible please delete the file."

SNMP-3-IFINDEXTABLEFILEINTWOFORMATS

3-Error

ifIndex-table is present in two formats.

Both nvram:ifIndex-table and nvram:ifIndex-table.gz are present.

snmp

"No action is necessary."

SNMP-3-IFINDEXTABLE_DECOMPRESSFAILED

3-Error

The file nvram:ifIndex-table.gz could not be decompressed.

There is either insufficient memory to compress it or the nvram space is insufficient or some other reason.

snmp

"If possible please delete the file."

SNMP-3-TOOMANYIFINDICES

3-Error

Some ifindices might not be persisted.

There are too many ifindices and the system is unable to persist all of them.

snmp

"Most likely this is a system limitation and there is no workaround."

SNMP-3-FILEOPENFAILED

3-Error

Could not open [chars].

The ifIndex-table is not accesible and hence the facility for ifindex persistence may not be available.

snmp

"Please debug using the debug ifs file command."

SNMP-3-FILESTATFAILED

3-Error

Could not get information for file [chars].

The ifIndex-table is not accesible and hence the facility for ifindex persistence may not be available.

snmp

"Please debug using the debug ifs file command."

SNMP-3-INCORRECT_SIZE_FOR_NVRAM

3-Error

Size should be > 0 but it is [dec].

There is some initialization problem in software.

snmp

"Ideally you should never see this message. If you do please report it at the earliest convenience."

SNMP-4-IFINDEXPERS_INTERNAL_ERROR

4-Warning

An internal error occurred in ifindex persistence code.

There is an unexpected internal error in ifindex persistence software.

snmp

""

SNMP-3-ISSU_ERR

3-Error

[chars]

Error happens when doing ISSU Versioning Operation

snmp

"Report this message to technical support"

SNMP-3-DUPLICATE_IFINDEX

3-Error

[chars] has [dec] duplicate ifIndices.

ifIndex-table file is corrupt. Ignoring duplicate entries.

snmp

"If ifIndex-table is not needed please delete the file from nvram."

SNMP-3-NON_POSITIVE_IFINDEX

3-Error

[chars] has [dec] non-positive ifIndices.

ifIndex-table file has some invalid entries that have non-positive\n\ ifIndex values. Ignoring invalid entries.

snmp

"If ifIndex-table is not needed please delete the file from nvram."

SNMP-3-INPUT_QFULL_ERR

3-Error

Packet dropped due to input queue full

Snmp packet dropped due to input queue full error

snmp

-

SNMP-3-INTERRUPT_CALL_ERR

3-Error

[chars] function cannot be called from interrupt handler

This message indicates that a call has been made to the function from\n\ an interrupt handler. This is not permitted because it will fail and \n\ device will reboot down the stack in malloc call.

snmp

"If this messages recurs copy it exactly as it appears and report\n\ it to your technical support representative."

SNMP-3-DVR_DUP_REGN_ERR

3-Error

Attempt for dupe regn with SNMP IM by driver having ifIndex [dec] and ifDescr [chars]

Driver is attempting to register an idb with the interface manager while there is already an interface with the same ifIndex and ifDescr BUT different idb registered. This would lead into the problem that interface counters shown by snmp would not work properly for this particular interface.

Component owner of the driver

"Fix the duplicate registration in driver level."

SNMP-3-DVR_DUP_REGN_WARNING

3-Error

Attempt for dupe regn with SNMP IM by driver having ifIndex [dec] and ifDescr [chars]

Driver is attempting to register the same idb with the interface manager while it's already registered. This is just a warning message and handled by snmp.

Component owner of the driver

"Fix the duplicate registration in driver level."

SNMP-3-MAX_TRAPS_EXCEED_ERR

3-Error

Maximum number of traps exceeded the maximum allowed in the current sync-message to STANDBY

This message indicates the number of SNMP traps defined exceeded the maximum we can accomodate in a checkpoint sync-message. You the developer need to increase SNMP_SYNC_BITMASK_MAX to a higher value. Please check smci_rf_status_event for further details.

snmp

"Developers will never see this error message."

SNMP-5-MODULERESET

5-Notice

[chars] object has been set to 'reset' for [chars]=[dec] from IP address [chars].

The SNMP server has reset a module.

none

"Notification message only. No action required."

SNMP-6-AUTHPROTOCOLMD5

6-Information

Authentication protocol md5 support will be deprecated in future

Authentication protocol support MD5 will be removed for SNMPV3 user creation in SNMP in future

snmp

"Notification message only. No action required."

SNMP-6-PRIVPROTOCOLDES

6-Information

Privacy protocol [chars] support will be deprecated in future

Privacy protocol support DES and 3DES will be removed for SNMPV3 user creation in future

snmp

"Notification message only. No action required."

SNMP-3-LICENSE_CHECK_FAILURE

3-Error

Bad OID License check failure while executing snmp-server view [chars] [chars] [chars]

This message indicates that snmp-server view command for a TAP MIB has failed as a result of missing License requirements.

-

"Please re-add the missing/failed configuration " "adhering to the License requirement to avoid inconsistency " "in the configuration."

SNMP-5-SNMP_SET_BLOCKED

5-Notice

SNMP SET Operation is blocked on STANDBY

This message indicates that on a platform where standby monitoring is enabled SET would be blocked to avoid any config changes on the device from the user.

none

"Do not execute SET on standby "

SNMP_ION-3-IFMIB_SHM_FAIL

3-Error

IF-MIB could not attach/create shared memory region

The IF-MIB maintains a part of its data structure in shared\n\ memory. In the process of creating/attaching/initializing\n\ this shared memory region a failure was detected.

Determine the component from the stack trace which indicates\n\ which subsystem is attempting to generate a trap. Search for\n\ similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP_ION-3-MIB_REG_FAIL

3-Error

MIB could not be registered with master agent

When a MIB is loaded in ION the OIDs are registered with the\n\ master agent. A failure was detected in this registration\n\ process

Determine the component from the stack trace which indicates\n\ which subsystem is attempting to generate a trap. Search for\n\ similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP_ION-2-PTHREADMUTEXFAIL

2-Critical

pthread_mutex_init failed on snmp mutex. Reason : [chars]

The snmp subagent failed to initialize the global mutex

ion

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MIB_ISSU-2-INIT

2-Critical

SNMP MIB ISSU client initialization failed to [chars]. Error: [dec] [chars]

The SNMP MIB ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

snmp

LOG_STD_ACTION

SNMP_MIB_ISSU-3-TRANSFORM_FAIL

3-Error

SNMP MIB ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The SNMP MIB ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the SNMP MIB state between the active device and the standby device is not identical.

snmp

"show issu session <client_id> and " "show issu negotiated version <session_id>"

SNMP_MIB_ISSU-3-MSG_NOT_OK

3-Error

SNMP MIB ISSU client 'Message Type [dec]' is not compatible

The SNMP MIB ISSU client received an incompatible message from the peer device. The message cannot be processed.

snmp

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SNMP_MIB_ISSU-3-MSG_SIZE

3-Error

SNMP MIB ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The SNMP MIB ISSU client failed to calculate the MTU for the specified message. The SNMP MIB ISSU client is not able to send the message to the standby device.

snmp

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SNMP_MIB_ISSU-3-INVALID_SESSION

3-Error

SNMP MIB ISSU client does not have a valid registered session.

The SNMP MIB ISSU client does not have a valid registered session.

snmp

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SNMP_MIB_ISSU-2-SESSION_REGISTRY

2-Critical

SNMP MIB ISSU client failed to register session information. Error: [dec] [chars]

The SNMP MIB ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

snmp

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SNMP_MIB_ISSU-3-SESSION_UNREGISTRY

3-Error

SNMP MIB ISSU client failed to unregister session information. Error: [dec] [chars]

The SNMP MIB ISSU client failed to unregister session information.

snmp

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SNMP_MIB_ISSU-2-SESSION_NEGO

2-Critical

SNMP MIB ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The SNMP MIB ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

snmp

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SNMP_MIB_ISSU-2-SEND_NEGO_FAILED

2-Critical

SNMP MIB ISSU client failed to send negotiation message. Error: [dec] [chars]

The SNMP MIB ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

snmp

"show logging and show checkpoint client"

SNMP_MIB_ISSU-2-GET_BUFFER

2-Critical

SNMP MIB ISSU client failed to get buffer for message. Error: [dec] [chars]

The SNMP MIB ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

snmp

"show logging and show checkpoint client"

SNMP_MIB_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

SNMP MIB ISSU client capability exchange result incompatible.

The SNMP MIB ISSU client capability exchange have negotiated as incompatible with the peer.

snmp

"show issu negotiated capability <Session_ID>"

SNMP_MIB_ISSU-3-CAP_INVALID_SIZE

3-Error

SNMP MIB ISSU client capability list is empty.

The SNMP MIB ISSU client capability exchange list size is invalid.

snmp

"show issu capability entires <Client_ID>"

SNMP_BULKSTAT-4-PRI_URL_UNREACHABLE

4-Warning

Primary network management station is unreachable for [chars]

The Collected Bulk data file could not be successfully transferred to the primary network management station address specified in the error message. This condition can occur because the primary network management address is not configured or the configured primary network management station address is unreachable. If a secondary network management station address is configured the collected bulk data file will be sent to the secondary network management station address.

snmp

"Ensure that the primary network management station address " "is configured. If the primary network management station " "address is configured check the connectivity to the " "destination indicated by the primary network management " " station address specified in the error message."

SNMP_BULKSTAT-4-SEC_URL_UNREACHABLE

4-Warning

Secondary network management station is unreachable for [chars]

The collected bulk data file could not be successfully transferred to the secondary network management station address destination specified in the error message. This condition can occur because the secondary network management station address is not configured or the configured secondary network management station address is unreachable. If a retention interval is not configured the bulk data file will be immediately deleted. If a retention interval is configured retries will be attempted for the configured number of times.

snmp

"Check the connectivity to destination indicated by secondary " "network management station address indicated in the error " "message"

SNMP_BULKSTAT-3-NO_MEMORY

3-Error

Memory not available for [chars] for [chars]

Data Collection or Transfer could not be successfully carried out because of lack of memory.

snmp

LOG_STD_REDUCE_ACTION

SNMP_BULKSTAT-4-BUFFER_OVERFLOW

4-Warning

Buffer size too small to accommodate data for one collection interval for [chars]

The bulk data file is too large for the configured buffer size for a single transfer interval. Data collection will continue in another new buffer of the configured size and the collected buffer will be transferred to the configured destination.

snmp

"Increase the maximum buffer size using the " "<CmdBold>buffer-size<NoCmdBold> size-of-buffer command " "where size-of-buffer is the increased buffer size."

SNMP_BULKSTAT-3-TOOSMALL_BUFFER

3-Error

Buffer size is insufficient to accommodate even the header part for [chars]

The buffer size is insufficient to accommodate the header for the bulk data file. The header contains the schema definitions of all the configured schemas.

snmp

"Increase the maximum buffer size using the " "<CmdBold>buffer-size<NoCmdBold> size-of-buffer command " "where size-of-buffer is the increased buffer size."

SNMP_BULKSTAT-3-REMOTE_FILE_WRITE_ERR

3-Error

File Write failed for the remote file [chars]

Username or password specified in the error message might not have the required privileges to write a file to the network management station specified in the error message or the destination directory specified in the error message is invalid.

snmp

"Ensure that the user name and password in the network " "management station address has the necessary privileges " "to write to the destination directory."

SNMP_CONTEXT_MAPPING-3-TOPO_NOT_BASE

3-Error

Multi Topology un-aware component is accessing a non base topology [chars] topoid [dec]

A software component that is not multi topology aware is\n\ accessing a non base topology. When this happens the result\n\ is un-predictable.

Determine the component from the stack trace which indicates\n\ which subsystem is causing this error. Search for\n\ similiar DDTS reports and open a DDTS.

"Copy the error message exactly as it appears and report it\n\ to your technical support representative."

SNMP_MGR-4-NOTENABLED

4-Warning

SNMP Manager not enabled requested by [chars]

An IOS application is attempting to make use of the SNMP manager's\n\ services. However the SNMP manager functionality has not been\n\ enabled.

-

"If you wish to enable the SNMP manager services you may do so via\n\ the 'snmp-server manager' config command. Otherwise the IOS\n\ application that is requesting these services is given in the\n\ message. Disable or reconfigure this application such that it no\n\ longer tries to make SNMP manager requests."

SNMP_MGR-3-NOPROC

3-Error

Failed to create SNMP Manager process

The SNMP manager process was unable to initialize. This is most\n\ likely due to a lack of memory.

snmp

"Copy the error message exactly as it appears and report it to\n\ your technical support representative. Use the show memory\n\ command to examine the amount of available memory. If free\n\ memory is low you may need to reconfigure and/or reload the\n\ system."

SNMP_MGR-3-RESPDROP

3-Error

Insufficient memory to handle response to request id [dec]

An SNMP response PDU was received but there was not enough\n\ memory available in order to cache the response and return it\n\ to the original requesting IOS application.

snmp

"If this was only a transient problem the original SNMP request\n\ will likely be resent another SNMP response will be returned\n\ and delivered to the original requesting IOS application. If\n\ this message repeats then you will need to free up some memory\n\ in order for the SNMP manager to function. Use show memory to\n\ verify whether available memory is low. You may need to reconfigure\n\ and/or reload the system in order to free up some memory. Otherwise\n\ you can disable the SNMP manager functionality via the no\n\ snmp-server manager command."

SNMP_MGR-3-BADAGETIMER

3-Error

Unexpected age timer found on session %0x

An internal timer was found running when it should not have been.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. Disable the SNMP manager via\n\ the no snmp-server manager command. Then re-enable it via the\n\ snmp-server manager command. This should effectively reset all of\n\ the internal structures."

SNMP_MGR-3-BADUSECOUNT

3-Error

Corrupted use counter found on session %0x

A cached SNMP session structure appears to have been corrupted.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. Disable the SNMP manager via\n\ the no snmp-server manager command. Then re-enable it via the\n\ snmp-server manager command. This should effectively reset all of\n\ the internal structures."

SNMP_MGR-3-BADPDUTYPE

3-Error

Received unknown PDU type: [dec]

The SNMP manager was delivered a PDU of an unknown type.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-3-BADTRANSPORT

3-Error

Unknown transport type: [dec]

The SNMP manager was delivered a PDU from an unknown transport type.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-3-SESSIONINUSE

3-Error

Attempt to destroy session %0x that is still in use

An attempt was made to remove a cached SNMP session structure\n\ however it appears that the session is still in use and therefore\n\ should not be removed.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-3-BADOP

3-Error

Unknown operation code [dec]

An SNMP PDU delivered to the SNMP manager contains an unknown\n\ operation code.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-3-MISSINGHOST

3-Error

Cannot locate information on SNMP informs host: [inet]

A table entry for the mentioned SNMP informs destination cannot\n\ be found. As a result inform notifications will not be sent to\n\ this destination.

snmp

"Run the 'show snmp host' and 'show snmp' commands. Copy the error\n\ message and output from the show commands exactly as they appear\n\ and report it to your technical support representative.\n\ Deleting and re-adding the informs destination via the\n\ 'snmp-server host' configuration command may clear the condition.\n\ Otherwise reloading the system may be necessary."

SNMP_MGR-3-MISSINGHOSTIPV6

3-Error

Cannot locate information on SNMP informs host: %P

A table entry for the mentioned SNMP informs destination cannot\n\ be found. As a result inform notifications will not be sent to\n\ this destination.

snmp

"Run the 'show snmp host' and 'show snmp' commands. Copy the error\n\ message and output from the show commands exactly as they appear\n\ and report it to your technical support representative.\n\ Deleting and re-adding the informs destination via the\n\ 'snmp-server host' configuration command may clear the condition.\n\ Otherwise reloading the system may be necessary."

SNMP_MGR-3-BADINFORMTRANSPORT

3-Error

Unknown inform transport type: [chars]

This SNMP inform destination uses an unknown transport type.\n\ Inform notifications cannot be sent to this destination.

snmp

"Copy the error message and the output from 'show techsupport' exactly\n\ as it appears and report it to your technical support representative."

SNMP_MGR-4-EMPTYQUEUE

4-Warning

Input queue is empty

The SNMP Manager process was notified that it needs to process\n\ it's input queue. But when the queue was examined it was found\n\ to be empty.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-4-BADRESPONSESTATUS

4-Warning

Unknown response status code: [dec]

The SNMP Manager process received an internal response with an\n\ unknown status code.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-4-BADAUTHTYPE

4-Warning

Unsupported SNMP authorization type: [dec]

An unknown SNMP authorization type was found. This may result in\n\ the inability of the SNMP manager functionality to correctly send\n\ and/or receive SNMP messages to/from a particular SNMP agent.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNMP_MGR-4-NOCANCEL

4-Warning

Unable to cancel a previously sent inform request.

The number of unacknowledged inform requests in-flight has reached\n\ the configured maximum limit. In order to make available resources\n\ for sending out a new inform request one of these older inform\n\ requests must be cancelled. The algorithm used to choose the most\n\ appropriate inform to cancel has failed to choose any. The new inform\n\ that was to be sent will be dropped instead.

snmp

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SPA_CHOCX_W2RP-5-PATH_UPDOWN

5-Notice

-

-

-

-

Path [chars] changed state to [chars]

A Sonet high order path changed its state.

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "controller sonet<NoCmdBold>. Look into this " "output to see if there are any alarms being " "reported at the path level. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

-

-

SPA_CHOCX_W2RP-5-T3_UPDOWN

5-Notice

T3 [chars] changed state to [chars]

A T3 within STS1 changed its state.

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "controller sonet<NoCmdBold>. Look into this " "output to see if there are any alarms being " "reported at the T3 level. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_W2RP-3-CORRUPT

3-Error

-

-

-

-

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupt

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "running-config<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

-

-

SPA_CHOCX_W2RP-1-ALLOCFAIL

1-Alert

-

-

-

-

OC3/STM1 [dec]/[dec] [chars] allocation failure

CHOCX controller or channel memory allocation failure

c7600-sip-200

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> oir plugin<NoCmdBold> when the problem " "is happening. Check Bug Toolkit before calling the " "TAC. When calling the TAC please provide the above" "information along with output of <CmdBold>show " "logging<NoCmdBold> and the output of <CmdBold>show " "tech<NoCmdBold> details."

-

-

SPA_CHOCX_W2RP-3-TIMEOUT

3-Error

-

-

-

-

Interface [chars]: [chars]

The CHOCX RP driver queries the LC for SONET information the LC didn't reply.

c7600-sip-200

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> command<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with the " "output of <CmdBold>show logging<NoCmdBold> and the " "output of <CmdBold>show tech<NoCmdBold details."

-

-

SPA_CHOCX_W2RP-3-PLUGIN_ERR

3-Error

[chars]

The RP plugin encountered an error during one of the Plugin calls

c7600-sip-200

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> oir plugin<NoCmdBold> when the problem " "is happening. Check Bug Toolkit before calling the " "TAC. When calling the TAC please provide the above " "information along with the output of <CmdBold>show " "logging<NoCmdBold> and the output of <CmdBold>show " "tech<NoCmdBold> details."

SPA_CHOCX_W2RP-3-NULL_SUBBLOCK

3-Error

-

-

-

-

Null ssb for [chars]

The hwidb subblock is NULL

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "running-config<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show running<NoCmdBold> " "and <CmdBold>show tech<NoCmdBold> details."

-

-

SPA_CHOCX_W2RP-3-APS_CMD_FAIL

3-Error

-

-

-

-

Failed to send APS command [hec] to [chars] retcode [hec]

APS command sending failed

c7600-sip-200

"This is a internal software error. If this " "error happened while configuring APS try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION

-

-

SPA_CHOCX_W2RP-3-FRR_ERROR

3-Error

-

-

-

-

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing

c7600-sip-common

"This is a internal software error. If this " "error happened while configuring FRR try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION

-

-

SPA_CHOCX_W2RP-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed

c7600-sip-200

"Inform the network operator that subrate " "configuration changed by remote end"

SPA_SE1-3-MEM_CPU_BIST_ERR

3-Error

[chars]: CPU BIST failure detected with error [chars] error code = 0x[hec].

The service SPA CPU Build-In Self Test BIST to check memory used

-

BUTLER_MEM_ERROR_STD_ACTION

SPA_SE1-3-MEM_INIT_ERR

3-Error

[chars]: memory init failure occurred [chars] with error [chars] error code = 0x[hec].

The service SPA memory initialization procedure failed.

-

BUTLER_MEM_ERROR_STD_ACTION

SPA_SE1-5-NO_VALID_PARTITION

5-Notice

[chars]: no valid partition was found in disk drive [chars] error code = 0x[hec].

The disk driver in service SPA doesn't have valid partition.

spa-butler-all

"Follow the instructions on the Cisco IOS installation and configuration " "guide to format the disk drive to correct this problem."

SPA_SE1-5-NO_APPL_IN_DISK

5-Notice

[chars]: no application image was found in disk drive.

The disk driver in service SPA doesn't have a valid application image.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-5-BOOTING_HELPER

5-Notice

[chars]: booting the helper image.

The service SPA is booting the helper image from bootflash.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-5-BOOTING_DEFAULT_APPL

5-Notice

[chars]: booting the default application image.

The service SPA is booting the default application image from disk.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-5-BOOTING_HOST_IMAGE

5-Notice

[chars]: booting application image downloaded from host.

The service SPA is booting the default application image from disk.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-SW_ERR

3-Error

NULL

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-butler-all

"The SPA driver has encountered a software error. Power down and reseat " "the indicated SPA card. If the problem persists copy the error message " "exactly as it appears on the console and open a case with the Technical " "Assistance Center via the Internet at " TAC_CASE_OPEN " or contact your " "Cisco technical support representative and provide the representative " "with the information you have gathered. Be sure to attach to your case " "the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SPA_SE1-3-MAINTENANCE_MODE

3-Error

Service engine [chars] has been booted in maintenance mode. This is an engineering use only mode and some or all of the SPA functions could be disabled.

The SPA was booted with <CmdBold>test hw-module subslot<NoCmdBold> <CmdArg>subslot#<NoCmdArg> <CmdBold>maintenance-mode enable<NoCmdBold> configured. Disable this mode and reload the SPA for normal SPA operation

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-ROMMON_BOOT_ERR

3-Error

[chars]: ROMMON boot error detected [chars] - [chars]

Service SPA ROMMON error was detected during booting of the SPA. The system will attempt to reload the SPA to recover from the failure.

spa-butler-all

BUTLER_ROMMON_ERROR_STD_ACTION

SPA_SE1-3-HELPER_BOOT_ERR

3-Error

[chars]: Helper image boot error detected [chars] error code = 0x[hec].

Service SPA helper image error was detected during booting of the SPA.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-APPL_BOOT_ERR

3-Error

[chars]: Application boot error detected [chars] with error [chars] error code = 0x[hec].

Service SPA application error was detected during booting of the SPA.

spa-butler-all

BUTLER_APPBOOT_ERROR_STD_ACTION

SPA_SE1-3-DEFAULT_APPL_BOOT_TIMEOUT

3-Error

[chars]: Timeout booting the default application image will attempt to boot the helper image.

Initialization of service SPA timed out during booting of the default application image the system will attempt to recover from the failure by trying to boot the helper image.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-APPL_BOOT_TIMEOUT

3-Error

[chars]: Timeout booting application image.

Initialization of service SPA timed out during booting of the sipspawmak9 sub-package. The system will attempt to reload the SPA to recover from the failure.

spa-butler-all

BUTLER_APPBOOT_ERROR_STD_ACTION

SPA_SE1-3-ROMMON_BOOT_TIMEOUT

3-Error

[chars]: Timeout booting ROMMON image in [chars] state [chars] - [chars]

Initialization of service SPA timed out during booting of the ROMMON image the system will now attempt to reload the SPA to recover from the failure.

spa-butler-all

BUTLER_ROMMON_ERROR_STD_ACTION

SPA_SE1-3-ROMMON_SPI4SYNC_TIMEOUT

3-Error

[chars]: Timeout getting SPI4 sync from ROMMON

Initialization of the service SPA timed out after failing to get SPI4 sync. The system will attempt to reload the SPA to recover from the failure.

spa-butler-all

BUTLER_ROMMON_ERROR_STD_ACTION

SPA_SE1-3-ROMMON_IMG_RECOVER

3-Error

[chars]: ROMMON boot failed recovering ROMMON image with backup copy.

A service SPA ROMMON error was detected during booting of the SPA. An attempt to re-program the ROMMON image will be performed to recover from this failure. This problem could have been caused by a previous interruption of the ROMMON FPD upgrade operation.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-BOOTFLASH_DEBUG_MODE

3-Error

Service engine [chars] has been booted in bootflash debug mode. This is an engineering use only mode and some or all of the SPA functions could be disabled.

The SPA was booted with <CmdBold>test hw-module subslot<NoCmdBold> <CmdArg>bay_num<NoCmdArg> <CmdBold>bootflash debug enable<NoCmdBold> configured. Disable this mode and reload the SPA for normal SPA operation.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-CHECKING_DISK

3-Error

[chars]: Disk is being checked because of previous unclean shutdown of the SPA or mount count limit reached. Boot time will take longer because of this operation e.g. 5 to 7 minute for a 250GB disk.

Checking of the disk file system is being performed to correct any error due to unclean shutdown of the SPA. Make sure that the SPA is properly shutdown before removing it from the system to prevent file system corruption.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-DISK_CHECKING_TIMEOUT

3-Error

[chars]: Timeout checking the disk after more than [dec] seconds. Another attempt to check the disk will be done after the SPA reload.

The disk checking operation has not completed in the expected time frame. To recover from possible disk checking failure the SPA will be reloaded to allow a retry of the disk checking operation.

spa-butler-all

BUTLER_DISK_FS_ERROR_STD_ACTION

SPA_SE1-3-SKIPPED_DISK_MOUNT

3-Error

[chars]: Disk mounting operation has been skipped for manual disk repair operation. Please follow the procedures on hardware configuration guide on how to enter into service engine console to continue with the disk repair operation.

The SPA was configured to not mount the disk after a reload operation. This is the initial step to prepare the SPA for manual disk repair operation.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SE1-3-DISK_NOT_PRESENT

3-Error

[chars]: Cannot detect the presence of disk drive on the SPA. Please check for loose cable connection to the drive. The SPA will continue operating without the disk.

The disk was not detected by the SPA during bootup and this will prevent the SPA from operating under normal conditions. The ability to store error logging on the disk will not be available and any debugging information will be lost after a SPA reload. Performance of the SPA might also get affected because of reduced memory storage.

spa-butler-all

BUTLER_DISK_STATE_ERROR_STD_ACTION

SPA_SE1-3-DISK_UNKNOWN_STATE

3-Error

[chars]: The disk drive on the SPA is in a unknown operational state. Check for a loose cable connection to the drive. The SPA will continue operating without the disk.

The disk was in an unknown operational state during SPA bootup and this will prevent the SPA from operating under normal conditions. The ability to store error logging on the disk will not be available and any debugging information will be lost after a SPA reload. Performance of the SPA might also get affected because of the reduced memory storage.

spa-butler-all

BUTLER_DISK_STATE_ERROR_STD_ACTION

SPA_SE1-3-DISK_UNFORMATTED

3-Error

[chars]: The disk drive on the SPA it is not formatted. The SPA cannot use an unformatted disk. Please follow instructions in the Cisco IOS installation and configuration guide to perform the manual format operation. The SPA will continue operating without the disk.

The disk was not formatted and this will prevent the SPA from operating under normal conditions. The ability to store error logging on the disk will not be available and any debugging information will be lost after a SPA reload. Performance of the SPA might also get affected because of the reduced memory storage.

spa-butler-all

"Follow the instructions on the Cisco IOS installation and configuration " "guide to format the disk drive to correct this problem."

SPA_SE1-3-DISK_CHECK_ERROR

3-Error

[chars]: Disk file system check error detected manual execution of disk checking operation will be required to correct this problem. The SPA will continue operating with reduced disk space.

An error was detected during automatic checking operation of disk file system integrity. The affected disk partition won't be mounted and this will prevent the SPA from operating under normal conditions. The ability to store error logging on the disk might not be available and any debugging information could be lost after a SPA reload. Performance of the SPA might also get affected because of the reduced memory storage.

spa-butler-all

BUTLER_DISK_FS_ERROR_STD_ACTION

SPA_SE1-3-DISK_MOUNT_ERROR

3-Error

[chars]: Disk mount error detected manual execution of disk checking operation might be required to correct this problem. The SPA will continue operating with reduced disk space.

Error were detected during mounting operation of disk partition. The affected disk partition won't be mounted this will prevent the SPA from operating at normal condition. Capability to store error logging on the disk might not be available and any debugging information could be lost after SPA reload. Performance of the SPA might also get affected because of the reduced memory storage.

spa-butler-all

BUTLER_DISK_FS_ERROR_STD_ACTION

SPA_SE1-3-CHECK_SPA_CONNECTOR

3-Error

[chars]: SPI4 error was detected during bootup automatic reload operation will be attempted for recovering the SPA. Please make sure that the SPA is secured properly in the SIP slot.

SPI4 error has occurred during SPA bootup. The SPA has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the SPA will be made. This message is likely due to bad connection of the SPA connector with the SIP slot.

spa-butler-all

"Pull out and reinsert the SPA to make secure connection " "with the SIP slot. Before removing the SPA make sure to stop the SPA " "by entering the <CmdBold>hw-module subslot<NoCmdBold> <CmdArg>slot#/" "subslot#<NoCmdArg> <CmdBold>stop<NoCmdBold> command. Remove the SPA " "wait 5 seconds and reinsert the SPA into the SIP. If the problem " "persists check for physical damage in the connector of both SPA and " "SIP. If no damage is visible then copy the error message exactly as it " "appears and gather the output from the <CmdBold>show hw-module subslot" "<NoCmdBold> <CmdArg>bay_num<NoCmdArg> <CmdBold>tech-support<NoCmdBold> " "command from the SIP console then contact your Cisco technical support " "representative with the gathered information."

SPA_SE1-3-SYSINIT_FAILURE

3-Error

[chars]: System init failure was detected during bootup - [chars]. SPA will be disabled because of this failure.

A failure was detected during system bootup of the SPA. The SPA has been deactivated because of the problem.

spa-butler-all

"Copy the error message exactly as it appears on the console and gather " "the output from the <CmdBold>show hw-module subslot<NoCmdBold> <CmdArg>" "bay_num<NoCmdArg> <CmdBold>tech-support<NoCmdBold> command from the " "SIP console. Contact your Cisco technical support representative with " "the gathered information."

SSFP_VCOP-4-CONF_ADD

4-Warning

VCoP SSFP is Configured \ on interface [chars]\n

VCoP SSFP is Configured

-

"None - normal situation"

SSFP_VCOP-4-CONF_DEL

4-Warning

VCoP SSFP is Unconfigured on \ interface [chars]\n

VCoP SSFP is Unconfigured

-

"None - normal situation"

SSFP_VCOP-4-CONF_EXIST

4-Warning

Port Type is already \ configured on this interface [chars].\n \ %%Remove the existing VCoP configuration and try again.\n

VCoP configuration is already present.

-

"None - normal situation"

SSFP_VCOP-4-CONF_ERROR_ADD

4-Warning

Failed to Configure VCoP \ on interface [chars]\n

Failed to configure VCoP

-

"None - normal situation"

SSFP_VCOP-4-CONF_ERROR_DEL

4-Warning

Failed to Unconfigure VCoP \ on interface [chars]\n

Failed to unconfigure VCoP

-

"None - normal situation"

SSFP_VCOP-4-DEV_INS

4-Warning

VCoP SSFP is Inserted into [chars]\n

VCoP SSFP is Inserted

-

"None - normal situation"

SSFP_VCOP-4-DEV_REM

4-Warning

VCoP SSFP is Removed from [chars]\n

VCoP SSFP is Removed

-

"None - normal situation"

SSFP_TPOP-4-CONF_ADD

4-Warning

TPoP SSFP is Configured \ on interface [chars]\n

TPoP SSFP is Configured

-

"None - normal situation"

SSFP_TPOP-4-CONF_DEL

4-Warning

TPoP SSFP is Unconfigured on \ interface [chars]\n

TPoP SSFP is Unconfigured

-

"None - normal situation"

SSFP_TPOP-4-CONF_EXIST

4-Warning

Port Type is already \ configured on this interface [chars].\n \ %%Remove the existing TPoP configuration and try again.\n

TPoP configuration is already present.

-

"None - normal situation"

SSFP_TPOP-4-CONF_ERROR_ADD

4-Warning

Failed to Configure TPoP \ on interface [chars]\n

Failed to configure TPoP

-

"None - normal situation"

SSFP_TPOP-4-CONF_ERROR_DEL

4-Warning

Failed to Unconfigure TPoP \ on interface [chars]\n

Failed to unconfigure TPoP

-

"None - normal situation"

SPAWBCMTS-3-INVALIDDATA

3-Error

Invalid information [chars] received by wideband software routine

Wideband SPA software module was passed invalid information

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-3-HWINITFAILED

3-Error

Error while initializing wideband group interface [chars]

Wideband group interface initialization error

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-3-SPAHANDLERFAIL

3-Error

The SPA was unable to process/handle the received data

Wideband SPA was unable to process/handle the received data

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-4-SFP_OK

4-Warning

[chars] [chars] SFP inserted in port [dec]

SFP inserted into the SPA

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-4-SFP_MISSING

4-Warning

[chars] [chars] SFP missing from port [dec]

SFP missing from SPA

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-4-SFP_UNINITIALIZED

4-Warning

[chars] [chars] SFP inserted in port [dec] failed initialization

SFP initialization failed

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-4-SFP_INCOMPATIBLE

4-Warning

[chars] [chars] SFP inserted in port [dec] incompatible with [chars] mode

SFP incompatible with current mode

-

-

SPAWBCMTS-4-SFP_INCOMP_REMOVE

4-Warning

[chars] the incompatible [chars] SFP removed from port [dec]

SFP incompatible removed

-

-

SPAWBCMTS-4-SFP_INTERNAL

4-Warning

[chars] [chars] SFP inserted in port [dec]. \n\NOTE: This type of SFP is not officially supported. You configured \service \internal\ so enabled for lab test.\nIf this is not your intent please \disable the configuration and oir the SFP.

SFP not supported offically.

-

-

SPAWBCMTS-4-SFP_NOTSUPPORTED

4-Warning

[chars] [chars] SFP inserted in port [dec] is not supported and disabled

SFP is not supported and disabled.

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-4-SFP_LINK_OK

4-Warning

[chars] port [dec] link changed state to up

Link status is up on SPA SFP

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-4-SFP_LINK_LOST

4-Warning

[chars] port [dec] link changed state to down

Link status is down on SPA SFP

cmts-vpa

LOG_STD_ACTION

SPAWBCMTS-5-SWITCHOVER_PRI

5-Notice

primary portport 0 will be active for [chars]

TenGigaEth link is being restored for primary port

cmts-vpa

"if not expected check secondary port in SPA"

SPAWBCMTS-5-SWITCHOVER_SEC

5-Notice

secondary portport 1 will be active for [chars]

TenGigaEth link is lost for primary port

cmts-vpa

"if not expected check secondary port in SPA"

SPAWBCMTS-2-CARD_UP_DOWN

2-Critical

Card [chars] in bay [dec]/[dec]/[dec] is [chars].

Card up/down

cmts-vpa

LOG_STD_ACTION

WBCMTS_GIGE-4-LINK_ERROR

4-Warning

[chars]

error in Gige link state update protocol

cmts-vpa

LOG_STD_ACTION

MCT1E1-3-INITFAIL

3-Error

MCT1E1 bay [dec] Init Failed at [chars] - line [dec] arg [hec]

The SPA failed to complete hardware initialization.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative."

MCT1E1-3-UNCOR_MEM_ERR

3-Error

[chars]: [dec] uncorrectable [chars] memory errors encountered.

The SPA driver detected an uncorrectable memory error condition on the SPA card. Packet corruption may result.

-

"The SPA driver has encountered an uncorrectable memory error on the SPA " "card. The hexadecimal memory address of the most recent error is " "specified in the message text on the console or in the system log. " "Please power down and reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-3-BAD_SIZE_ERR

3-Error

[chars]: [dec] [chars] events on HDLC Controller were encountered. The SPA is being Restarted.

The SPA driver detected an error event on the HDLC controller.

-

CTE1_STD_ACTION

MCT1E1-3-HDLC_CTRL_ERR

3-Error

[chars]: [dec] [chars] events on HDLC Controller were encountered.

The SPA driver detected an error event on the HDLC Controller.

-

"The SPA driver has encountered an error event on the SPA card. " CTE1_STD_ACTION

MCT1E1-3-COR_MEM_ERR

3-Error

[chars]: [dec] correctable [chars] memory errors encountered.

The SPA driver detected a correctable memory error on the SPA card.

-

"The SPA has encountered a correctable memory error on the SPA card. " "The error has been corrected and normal processing should continue. " "The hexadecimal memory address of the most recent error is specified " "in the message text on the console or in the system log. " CTE1_STD_ACTION

MCT1E1-3-UNCOR_PARITY_ERR

3-Error

[chars]: [dec] [chars] parity errors encountered.

The SPA driver detected an uncorrectable parity error condition on the SPA card. Packet corruption may result.

-

"Please power down and reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-2-CMD_DROP

2-Critical

[chars] cmd: [dec] arg0: [dec] arg1: [dec] arg2: [dec] arg3: [dec] vc: [dec] reason: [chars]

The SPA driver dropped a configuration command. One or more interfaces or controllers associated with the SPA may not be configured correctly.

-

"Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the condition persists " "copy the error message exactly as it appears and report it to your " "technical support representative. Please also supply a " "<CmdBold>show tech-support<NoCmdBold> at that time."

MCT1E1-2-EV_DROP

2-Critical

[chars] cmd: [dec] arg0: [dec] arg1: [dec] arg2: [dec] arg3: [dec] reason [chars]

The SPA driver dropped an event notification command. Counters or line protocols for one or more interfaces or controllers may be incorrect.

-

"Please restart any interfaces or controllers that are down. " "If the condition persists copy the error message exactly as " "it appears and report it to your technical support representative. " "Please also supply a <CmdBold>show tech-support<NoCmdBold> at that " "time."

MCT1E1-3-FRMR_CLKFAIL

3-Error

[chars]: Framer input clock failure detected CTCLK = [chars]CTIVE LREFCLK = [chars]CTIVE SREFCLK = [chars]CTIVE ctclk count [dec] lrefclk count [dec] srefclk count [dec]

The SPA driver detected failure of one ore more input clocks to the framer chip. The T1/E1 Ports may not operate as expected.

-

"The SPA driver has detected input clock failures on the framer chip. " "If the ports on the SPA are not operating as expected power down and " "reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-3-BATCH_CMD_INVALID_TAG

3-Error

[chars]: Invalid tag value [dec] at index [dec].

The SPA driver detected invalid tag value in a batch command.

spa-ser-te1

"The SPA driver has detected invalid command format from RP. " "If the ports on the SPA are not operating as expected power down and " "reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-3-PERIODIC_PROCESS

3-Error

[chars]: periodic process error [chars].

The SPA driver detected an error with periodic processing routine.

spa-ser-te1

"The SPA driver has detected problem with periodic routine. " "If the ports on the SPA are not operating as expected power down and " "reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-3-CMD_FAILED

3-Error

[chars]: Failed to send command '[chars]' to SPA - [chars].

The SPA driver could not successfully send a cmd to firmware.

spa-ser-te1

"The SPA driver has detected a command failure. " "If the ports on the SPA are not operating as expected power down and " "reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-3-AUTODNR

3-Error

[chars] failed for slot [dec] bay [dec] err [dec]

AUTODNR/USNDNR process has failed. The SPA and SIP are out of synchronization. This condition indicates a software error.

spa-ser-te1

LOG_STD_ACTION

MCT1E1-3-TIMEOUT

3-Error

[chars]: [chars] failed: [dec] state: [dec] ml_id: [dec] progress: [dec]

Linkrec is stuck at non ready. This condition indicates a software error.

spa-ser-te1

LOG_STD_ACTION

MCT1E1-3-QUEUE_HALT_FAIL

3-Error

[chars]: Could not suspend message [dec] or command [dec] queue

-

-

-

MCT1E1-3-SPI4_HW_ERR

3-Error

[chars]: [chars] Hardware error was encountered.

The SPA driver detected a Hardware error condition on the SPA card. This might result in improper operation.

-

"The SPA driver has encountered a Hardware error on the SPA's SPI4 bus." "Please power down and reseat the indicated SPA card. " CTE1_STD_ACTION

MCT1E1-3-FPGA_CNTR_ERR

3-Error

[chars]: [dec] [chars] errors encountered.

-

-

-

MCT1E1-3-BERT_STOP_ERR

3-Error

[chars]: Failed to stop BERT operation on interface [chars] - [chars].

The SPA failed to stop the BERT operation on the indicated interface. The interface might not be functional after this event if that is the case try to 'shutdown' and then 'no shutdown' the interface to recover from this failure.

spa-ser-te1

"If manual 'shutdown' and then 'no shutdown' of the interface does " "not restore the operation then SPA will need to be reloaded to " "recover from this failure state."

MCT1E1-3-BERT_OPERATION_ERR

3-Error

[chars]: BERT operation error on interface [chars] - [chars].

The SPA reported failure during BERT operation. The current BERT operation will be terminated but the affected interface might not be operational if that is the case try to 'shutdown' and then 'no shutdown' the interface to recover from this failure.

spa-ser-te1

"If manual 'shutdown' and then 'no shutdown' of the interface does " "not restore the operation then SPA will need to be reloaded to " "recover from this failure state."

MCT1E1-3-LOOP_UNSUPPORTED

3-Error

[chars]: [chars] on port [dec]/[dec]/[dec] and it is not supported on SPA.

The SPA driver received 'loopback payload' request from the remote device on the SPA card. SPA does not support loopback payload.

-

"The SPA driver has received 'loopback payload' request from the remote " "device on the SPA card. SPA does not support loopback payload. " "The remote request is ignored. Please unconfigure the command on the " "remote device. "

MCT1E1-3-LOOPBACK_CFG_ERR

3-Error

[chars]: Loop [chars] configuration error on controller [chars] - [chars][chars].

The SPA reported failure during setting of loop up/down operation. The current loopback will be terminated but the affected controller might not be operational if that is the case try to 'shutdown' and then 'no shutdown' the controller to recover from this failure.

spa-ser-te1

"If manual 'shutdown' and then 'no shutdown' of the controller does " "not restore the operation then SPA will need to be reloaded to " "recover from this failure state."

PCM_TRACER-3-PCMT_NO_DEST

3-Error

No PCM Tracer capture destination configured.

Capture destination is required for starting the PCM Tracer.

PCM_TRACER_DDTS_COMPONENT

"Configure capture destination before starting the PCM Tracer."

PCM_TRACER-3-PCMT_NO_PROFILE

3-Error

No PCM Tracer profile configured.

Capture profile is required for starting the PCM Tracer.

PCM_TRACER_DDTS_COMPONENT

"Configure capture profile before starting the PCM Tracer."

PCM_TRACER-3-PCMT_NO_CAPTURE_TDM

3-Error

No capture-tdm configured under profile [dec].

Capture-tdm is required for starting the PCM Tracer.

PCM_TRACER_DDTS_COMPONENT

"Configure capture-tdm before starting the PCM Tracer."

PCM_TRACER-3-PCMT_NO_CAPTURE_DURATION

3-Error

No capture duration configured.

Capture duration is required for starting the PCM Tracer.

PCM_TRACER_DDTS_COMPONENT

"Configure capture duration before starting the PCM Tracer."

PCM_TRACER-3-PCMT_NO_ACTIVE_CALL

3-Error

No active calls to trace.

PCM Tracer can be applied only on active calls.

PCM_TRACER_DDTS_COMPONENT

"Make sure there is an active call before starting the PCM Tracer."

PCM_TRACER-3-PCMT_RUNNING

3-Error

A PCM Tracer session is currently running.

Can't execute this command since there is a PCM Tracer running now.

PCM_TRACER_DDTS_COMPONENT

"Make sure there is no PCM Tracer sesssion running before execute this " "command."

PCM_TRACER-3-PCMT_NOT_SUPPORTED

3-Error

PCM Tracer is not supported on slot [dec].

Can't execute this command on the slot number specified.

PCM_TRACER_DDTS_COMPONENT

"Refer to the user guide for which slot PCM Tracer is supported on."

PCM_TRACER-3-PCMT_CHANNEL_TYPE_NOT_SUPPORTED

3-Error

The channel/group type of ds0 [dec] is not supported by PCM Tracer.

Can't execute this command on the ds0 number specified.

PCM_TRACER_DDTS_COMPONENT

"Refer to the user guide for the channel/group type PCM Tracer " "supports."

PCM_TRACER-6-PCMT_START

6-Information

Starting PCM Trace on channel under profile [dec]

-

-

-

PCM_TRACER-6-PCMT_STOP

6-Information

Stopping PCM Trace on channel under profile [dec]

-

-

-

PCM_TRACER-6-PCMT_STOP_FAIL

6-Information

Fail to Stop PCM Trace on channel under profile [dec]

-

-

-

PCM_TRACER-6-PCMT_STOP_RUNNING

6-Information

Stop PCM capture

-

-

-

DS0_DUMP-3-MALLOC_PROC_MEM

3-Error

Process memory allocation failed for PCM capture: size 0x%08X.

The free process memory in the system is not enough for the PCM capture session.

DS0_DUMP_DDTS_COMPONENT

"Refer to the user guide for the estimation of process memory needed " "for PCM capture. Do 'show memory' to make sure there is enough memory " "before PCM capture starts."

DS0_DUMP-3-INIT_FAIL

3-Error

DS0 PCM Tracer is not initialized.

DS0 dump process can't be initialized.

DS0_DUMP_DDTS_COMPONENT

"Make sure there is enough memory in the system and IOS is properly " "installed."

DS0_DUMP-3-PCM_TRACER_RUNNING

3-Error

A previous session of PCM capture is in progress.

Can't start new PCM capture session since there is one going on now.

DS0_DUMP_DDTS_COMPONENT

"Make sure there is no other PCM capture session going on before " "start the new capture."

DS0_DUMP-3-PCM_TRACE_NOT_SUPPORTED

3-Error

PCM Trace/ds0 dump is not supported on slot [dec].

Can't execute this command on the slot number specified.

DS0_DUMP_DDTS_COMPONENT

"Refer to the user guide for which slot ds0 dump is supported on."

DS0_DUMP-3-PCM_TRACE_START_FAILED

3-Error

PCM capture start failed.

Failed to start the ds0 dump in the TDM driver.

DS0_DUMP_DDTS_COMPONENT

"Make sure there is no hardware defect and there is no other " "ds0 dump/test tdm dump session going on."

DS0_DUMP-6-PCM_TRACE_STARTED

6-Information

PCM capture started.

-

-

-

DS0_DUMP-6-PCM_TRACE_RSP_STARTED

6-Information

module start PCM capture for [dec]/[dec]/[dec]/[dec]

-

-

-

DS0_DUMP-6-PCM_TRACE_RSP_STOPPED

6-Information

module stop or complete PCM capture for [dec]/[dec]/[dec]/[dec]

-

-

-

DS0_DUMP-6-PCM_TRACE_RSP_ERROR

6-Information

module fail and terminate the pcm capture for [dec]/[dec]/[dec]/[dec]

-

-

-

DS0_DUMP-6-PCM_TRACE_RSP_UNKNOWN

6-Information

module send unkonwn pcm capture response [dec] for [dec]/[dec]/[dec]/[dec]

-

-

-

DS0_DUMP-6-PCM_TRACE_STOPPING

6-Information

stopping PCM capture

-

-

-

DS0_DUMP-6-PCM_TRACE_STOP_FAILED

6-Information

failed to stop PCM capture

-

-

-

DS0_DUMP-6-PCM_TRACER_NOT_RUNNING

6-Information

no PCM capture is in progress.

-

-

-

ASR1000_RP_CTE1_SPA-3-CCIPCFAIL

3-Error

Communication with the CC has failed for Interface [dec]/[dec]

Communication with Card-Carrier down.

mcp-io

"Either try to configure the Sharded Port Adapter at a later time or " "reload the Card Carrier."

ASR1000_RP_CTE1_SPA-3-IPCERR

3-Error

Internal IPC error [chars]

Internal IPC error.

mcp-io

"Either try to configure the Sharded Port Adapter at a later time or " "reload the SPA and/or Card Carrier."

ASR1000_RP_CTE1_SPA-3-UNSUPERR

3-Error

NULL

An internal error as resulted from an unsupported or unexpected message.

mcp-io

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ASR1000_SIP_CTE1_SPA-3-TDL_ARG_ERR

3-Error

Interface [dec]/[dec]/[dec]: Bad parameter in message from RP: [chars]

Bad parameter in message from RP.

mcp-io

"Either try to configure the Sharded Port Adapter at a later time or " "reload the Card Carrier."

ASR1000_SIP_CTE1_SPA-3-UNSUPERR

3-Error

NULL

An internal error as resulted from an unsupported or unexpected message.

mcp-io

"Copy the error message exactly as it appears and report it to your " "technical support representative."

ASR1000_SIP_POS_SPA-3-APS

3-Error

APS[dec] [chars]

RP deadman timer expired on CC CC is sending LAIS to far end

mcp-io

"Copy the error message exactly as it appears on the console \n\ or in the system log. Call your Cisco technical support \n\ representative and provide the representative \n\ with the gathered information."

ASR1000_SIP_POS_SPA-4-ALLOCFAIL

4-Warning

SPA resource allocation failed for subslot [dec]/[dec] while [chars]

The SPA driver in the subslot specified in the message is\n\ not able to allocate a system resource. The required system resource is\n\ specified in the message.

mcp-io

"Copy the error message exactly as it appears on the console \n\ or in the system log. Call your Cisco technical support \n\ representative and provide the representative \n\ with the gathered information."

POS_SPA_FRMR-3-RESTART_FAILURE

3-Error

Framer restart failed for SPA in [dec]/[dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart framer restart error has occured. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-RECONFIG_FAILURE

3-Error

Framer reconfiguration failed for SPA in [dec]/[dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart the framer reconfig error has occured. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-RECONCILE_FAILURE

3-Error

Framer reconcilation failure for SPA in [dec]/[dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart the framer reconcilation error has occured. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-TRANSMIT_DELAY_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of transmit-delay is

During Minimal Disruptive Restart the software and hardware copy of the transmit delay parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-CRC_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of crc is detected to be

During Minimal Disruptive Restart the software and hardware copy of the crc parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-MTU_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of mtu is detected to be

During Minimal Disruptive Restart the software and hardware copy of the mtu is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-FRAMING_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of framing is detected to be

During Minimal Disruptive Restart the software and hardware copy of the framing parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-C2_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of sonet c2 is detected to

During Minimal Disruptive Restart the software and hardware copy of the sonet C2 parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-S1S0_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of sonet S1S0 is detected

During Minimal Disruptive Restart the software and hardware copy of the sonet S1S0 parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-LOOPBACK_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of loopback is detected

During Minimal Disruptive Restart the software and hardware copy of the loopback parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-SCRAMBLE_MISMATCH

3-Error

The software [dec] and hardware [dec] copy of scrambling is detected

During Minimal Disruptive Restart the software and hardware copy of the scrambling parameter is found to be different. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_FRMR-3-NULL_DEV_OBJ

3-Error

-

Pointer to framer device object is NULL.

spa-pos-all

LOG_STD_SH_TECH_ACTION

POS_SPA_SPI4-3-RESTART_FAILURE

3-Error

SPI4 restart failed for SPA in [dec]/[dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart spi4 restart error has occured. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

POS_SPA_SPI4-3-RECONFIG_FAILURE

3-Error

SPI4 reconfiguration failed for SPA in [dec]/[dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart the spi4 reconfig error has occured. This indicates an error and the SPA will be reset as normal and will impact traffic.

spa-pos-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ASR1000_RP_POS_SPA-4-ALLOCFAIL

4-Warning

Interface [dec]/[dec] allocation failed: [chars]

required resources unavailable.

mcp-io

"Either upgrade system memory or reconfigure memory usage."

ASR1000_RP_POS_SPA-4-SFSDTHRESHOLDFAIL

4-Warning

Interface [chars]

failed to update CC about BER_SF_SD thresholds

asr1k-spa-pos

"Copy the error message exactly as it appears on the console\n\ or in the system log. Call your Cisco technical support\n\ representative and provide the representative\n\ with the gathered information."

ASR1000_RP_POS_SPA-4-APSGETFAIL

4-Warning

Interface [chars]

failed to get aps state from cc

asr1k-spa-pos

"Copy the error message exactly as it appears on the console\n\ or in the system log. Call your Cisco technical support\n\ representative and provide the representative\n\ with the gathered information."

SPA_OIR-3-MESSAGE_ERROR

3-Error

[chars]: SPA OIR event message error - [chars][dec]

An error was detected in a SPA OIR event message for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-UNEXPECTED_EVENT

3-Error

[chars]: SPA OIR unexpected event[dec]

An unexpected SPA OIR event was detected for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-INVALID_EVENT

3-Error

[chars]: Invalid [chars] event received when SPA is undergoing Minimal Disruptive Restart

An unexpected event was detected when the SPA was was undergoing Minimal Disruptive Restart. This condition is most likely a software problem. The SPA will be reset as normal and this will impact traffic.

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-EVENT_DATA_ERROR

3-Error

SPA OIR event data error - [chars][dec]

Invalid data was detected within a SPA OIR event. The SPA OIR state machines may not reflect the state of the hardware. The problem only affects one SPA but the SPA cannot be determined from the context where the error was detected. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

"Check the system log for other messages that may help determine " "which SPA is affected. " SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-POST_EVENT_ERROR

3-Error

[chars]: event [dec]

A SPA OIR event message was not enqueued for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition is most likely due to a software problem.

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-UNEXPECTED_RECOVERY_ACTION

3-Error

[chars]: SPA [chars] unexpected recovery action[dec] for fail code 0x[hec]

An error occured while processing a failure message for the SPA in the slot or subslot number specified in the error message. The recovery action to be taken after a SPA failure is determined by calling a SPA driver function. This message indicates that the SPA driver function returned an invalid recovery action. After this message was issued the SPA was reloaded in an attempt to recover. The SPA driver most likely returned an invalid recovery action because of a software problem.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-EVENT_HANDLING

3-Error

[chars]: [chars]0x[hec]

A data structure error was detected when handling a SPA OIR event for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware. This condition is most likely due to a software problem.

spa-infra

SPA_OIR_STD_ACTION

SPA_OIR-3-CMD_ATTR

3-Error

[chars]: Unexpected command identifier [dec]

An unexpected command identifier was detected when processing command related to a SPA OIR. The command was not processed. This is most likely due to a software problem.

spa-infra

SPA_OIR_STD_ACTION

SPA_OIR-2-INITFAIL

2-Critical

SPA OIR initialization error

A failure occurred during the SPA OIR subsystem startup. SPA OIR is not functional for the RP or line card that generated the message.

-

LOG_STD_REDUCE_ACTION

SPA_OIR-2-SUBSLOTINITFAIL

2-Critical

SPA OIR initialization error for [chars]

A failure occurred during the SPA OIR subsystem startup. SPA OIR is not functional for the slot or subslot specified in the error message

-

LOG_STD_REDUCE_ACTION

SPA_OIR-3-EVENT_TIMEOUT

3-Error

[chars]: Timeout waiting for SPA OIR event

A timeout occurred for the subslot specified in the error message while waiting for a SPA OIR event. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR event are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-SW_INIT_TIMEOUT

3-Error

[chars]: SPA initialization not completed

A timeout occurred for the subslot specified in the error message while waiting for SPA software driver to initialize the SPA. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by software firmware or hardware problem but a software or firmware problem is more likely.

-

"Check for other messages reported for futher insight. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco techinical support representative. " SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-HW_INIT_TIMEOUT

3-Error

[chars]

A timeout occurred for the subslot specified in the error message while waiting for SPA hardware to initialize. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by a software firmware or hardware problem but a firmware or hardware problem is more likely.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-OUT_OF_SYNC

3-Error

[chars]: failure code 0x[hec]

The software SPA OIR state did not match the hardware state for the subslot in the error message. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition is expected if a SPA is reloading when an RP switchover occurs. Otherwise this condition could be caused by a software firmware or hardware problem but a firmware or software problem is more likely. This condition could also be caused by a rare interaction between SPA and its SIP.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-HW_SIGNAL_DEASSERTED

3-Error

[chars]

The SPA was not brought up because the SPA bay is in an admin down state. The SPA bay will appear as <CmdBold>hw-module<NoCmdBold> <target spa> <CmdBold>shutdown<NoCmdBold> in the running configuration.

-

"Use the <CmdBold>no hw-module<NoCmdBold> <target spa> " "<CmdBold>shutdown<NoCmdBold> command to administratively enable " "the SPA bay."

SPA_OIR-6-PRECONFIG_MISMATCH

6-Information

[chars]: Inserted SPA type does not match preconfigured SPA type. Configuration updated

This message reports a mismatch between the inserted SPA type and the preconfigured SPA type on platforms that support pre-configuration. The inserted SPA replaces the preconfigured SPA.

-

"Check the configuration with the <CmdBold>show run<NoCmdBold> command. " "If you would like to revert to the preconfigured type remove the SPA " "and then update the configuration from a backup"

SPA_OIR-3-SPA_POWERED_OFF

3-Error

[chars]: SPA [chars] powered off after [dec] failures within [dec] seconds

The SPA was powered off because it failed too often. This condition may be caused by a software firmware or hardware error.

-

"Look for other error messages related to this SPA subslot to " "determine root cause of the failure. " SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-CORRUPT_EVENT

3-Error

[chars]

Corruption was detected within a SPA OIR event for the subslot specified in the error message. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by a software firmware or hardware problem but a firmware or software problem is more likely. For distributed platforms SPA OIR events are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-UNRECOGNIZED

3-Error

The SPA of type 0x%X in [chars] is not recognized

The type of the SPA in the specified subslot is not recognized by the operating system. The operating system might not support this SPA type on this platform or the SPA type identification stored on the SPA is invalid.

-

"Ensure that the system is running a version of the operating " "system that supports the SPA type specified in the error " "message on this platform. If the correct operating system " "version is in use copy the error message exactly as it " "appears on the console or in the system log contact your " "Cisco technical support representative and provide the " "representative with the gathered information. Include the " "information about the SPA type found on the front of the " "SPA."

SPA_OIR-3-UNSUPPORTED

3-Error

The [chars] in [chars] is not supported by the [chars] module

The SPA in the subslot specified in the error message is not supported in the specified SIP by the version of the operating system currently running on the system. The SPA type may be supported by another SIP or by a later operating system release.

-

"Ensure that the SIP specified in the error " "message supports the specified SPA type. Ensure that the " "operating system release supports the SPA type in the SIP. " "It may be necessary to upgrade your system to " "the latest operating system release in your release train or " "it may be necessary to use a different SIP type. If " "the SPA type specified in the error message does not match the " "interface types or numbers shown on the front of the SPA copy " "the error message exactly as it appears on the console or in " "the system log contact your Cisco technical support " "representative and provide the representative with the " "gathered information. Include information regarding the SPA " "type found on the front of the SPA."

SPA_OIR-3-RECOVERY_RELOAD

3-Error

[chars]: Attempting recovery by reloading SPA

The OIR facility attempted automatic recovery by reloading the SPA in the subslot specified in the error message. Look for other error messages related to this SPA subslot to determine the failure that triggered the automatic recovery.

-

LOG_STD_NO_ACTION

SPA_OIR-6-REMCARD

6-Information

Card removed from [chars] interfaces disabled

The OIR facility detected the removal of a SPA from the slot or subslot number specified in the error message. The interfaces on that SPA will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces.

-

LOG_STD_NO_ACTION

SPA_OIR-6-INSCARD

6-Information

Card inserted in [chars]

The OIR facility detected a newly inserted SPA. The interfaces associated with that SPA are operational but will be shut down until they are configured by the user. If any interfaces of that type were previously configured they will be restored to their previous state.

-

LOG_STD_NO_ACTION

SPA_OIR-6-ONLINECARD

6-Information

SPA [chars] online in [chars]

The OIR facility detected the state change to online for the SPA in the slot or subslot number specified in the message.

-

LOG_STD_NO_ACTION

SPA_OIR-6-OFFLINECARD

6-Information

SPA [chars] offline in [chars]

The OIR facility detected the state change to offline for the SPA in the slot or subslot number specified in the message.

-

LOG_STD_NO_ACTION

SPA_PLUGIN-3-FIRMWARE_BADPATH

3-Error

[chars]: Invalid firmware file path [chars].

Specified fireware file path is invalid. This is a software error.

spa-ser-infra

LOG_STD_ACTION

SPA_PLUGIN-3-FIRMWARE_NOMEMORY

3-Error

[chars]: Insufficient memory for firmware file [chars] size [dec].

Can not allocate memory for firmware image for downloading to SPA.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-FIRMWARE_BADIMAGE

3-Error

[chars]: Firmware file [chars] read failed.

Firmware image pointed by the path is not valid.

spa-ser-infra

LOG_STD_ACTION

SPA_PLUGIN-3-FIRMWARE_DOWNLOAD

3-Error

[chars]: Firmware download failed.

Failed to download firmware image to SPA. It is caused by either lack of memory on SPA IPC failures improperly seated SPA or other download errors.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-FIRMWARE_DOWNLOADING

6-Information

[chars]: Downloading SPA firmware [chars]...

Downloading SPA firmware.

-

"None. Information only."

SPA_PLUGIN-3-FIRMWARE_STARTUP

3-Error

[chars]: Firmware startup failed. SPA status0x%08x host status0x%08x

Can not start Firmware image downloaded to SPA. Possible causes are either bad image on SIP flash disk hardware failures or outdated FPGA and/or ROMMON image.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FIRMWARE_APPS_DOWNLOAD

3-Error

[chars]: Firmware application download failed.

Failed to download application image to SPA. It may be caused by either lack of memory on SPA IPC failures improperly seated SPA or other download errors.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-FIRMWARE_APPS_DOWNLOADING

6-Information

[chars]: Downloading SPA firmware application [chars]...

Downloading SPA firmware application .

-

"None. Information only."

SPA_PLUGIN-3-FIRMWARE_APPS_STARTUP

3-Error

[chars]: Firmware application startup failed. SPA status0x%08x host status0x%08x

Can not start application image downloaded to SPA. Possible causes might be either bad image on SIP flash disk hardware failure or outdated FPGA and/or ROMMON image.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FILE_ERROR

3-Error

[chars]: Error accessing file [chars].

Specified file is not found lack of permission out of space or other file system/device errors.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FILE_TRANSFER

3-Error

[chars]: Failed to transfer file to or from SPA.

Failed to transfer a file to or from SPA. It might be caused by lack of memory on SPA or jacket card IPC failures improperly seated SPA or other errors.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-PLIM_CREATE

3-Error

[chars]: PLIM subblock creation failed.

Can not allocate memory for PLIM structure.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-NOPLIM

3-Error

[chars]: No PLIM subblock.

Invalid pointer was passed in. Can not dereference PLIM subblock pointer. Internal error.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-RETRY_EXHAUSTED

3-Error

[chars]: plugin initialization failedretries exhausted.

One or more critical conditions happened that prevented plugin initialization from moving forward after designated number of retries. Preceeding messages may indicated failure cause.

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-FAILED

3-Error

[chars]: Plugin initialization failed.

Plugin initialization can fail for many reasons. Preceding messages may state the cause.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

spa-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-SPI4_CREATE

3-Error

[chars]: Device SPI4 creation failed.

Can not allocate memory for SPI4 structure.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-UART_CREATE

3-Error

[chars]: Device UART creation failed.

Can not allocate memory for UART structure.

spa-ser-infra

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-SPI4_SETCB

3-Error

[chars]: IPC SPI4 set callback failedstatus [dec].

Can not setup a callback function for SPI4 bus. It might be caused by improperly seated SPA outdated or a hardware failure.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-SPI4_SETCB_PORT

3-Error

[chars]: IPC SPI4 set callback failederror: [dec] for port [dec].

Can not setup a callback function for SPI4 bus for the specified interface port. It might be caused by improperly seated SPA outdated ROMMON/FPGA or a hardware failure.

spa-ser-infra

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-SPI4_CONFIG

3-Error

[chars]: Can not configure host side SPI4 profile.

SPI4 configuration from modular services card failed. It indicates either lack of system memory a hardware failure or an outdated ROMMON/FPGA image.

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-SPI4_NOTSYNC

3-Error

[chars]: Can not synchronize SPI4 bus.

SPI4 bus between modular services card and SPA is not synchronized. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image.

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-SPI4_SYNC

6-Information

[chars]: SPI4 bus synchronization achieved.

SPI4 bus between modular services card and SPA is synchronized.

-

"None. Information only."

SPA_PLUGIN-3-SPI4_INIT

3-Error

[chars]: SPI4 initializaion failed.

-

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-ENV_INIT

3-Error

[chars]: Environment monitoring initialization failed.

-

-

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-EFC_NOTSYNC

3-Error

[chars]: Can not synchronize EFC bus.

Extended flow control between modular services card and SPA is not synchronized. SPA is shut down. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image.

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-6-EFC_SYNC

6-Information

[chars]: EFC bus synchronization achieved.

Extended flow contorl between modular services card and SPA is synchronized.

-

"None. Information only."

SPA_PLUGIN-3-EXCEPTION

3-Error

[chars]: Exception with cause [dec].

One of SPA software components crashes.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-AUXC2W_CREATE

3-Error

[chars]: Device auxiliary C2W creation failed.

Can not allocate memory for auxiliary C2W structure.

-

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-4-LED_CREATE

4-Warning

[chars]: LED driver initialization failed.

Can not allocate memory for LED structure.

-

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-4-LED_READ

4-Warning

[chars]: LED read failed for port [dec] status [dec].

Can not read LED register values. It indicates either a not properly seated SPA or a hardware failure

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-4-LED_WRITE

4-Warning

[chars]: LED write failed for port [dec] status [dec].

Can not write to LED register. It indicates either a not properly seated SPA or a hardware failure

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-EEPROM_READ

3-Error

[chars]: Error reading EEPROM.

Can not read EEPROM content. It indicates either a not properly seated SPA or a hardware failure

-

SPA_STD_RESEAT_ACTION

SPA_PLUGIN-3-IOFPGA_CREATE

3-Error

[chars]: Device IOFPGA creation failed.

Can not allocate memory for IOFPGA structure.

-

LOG_STD_REDUCE_ACTION

SPA_PLUGIN-3-ROMMON

3-Error

[chars]: ROMMON reports error. SPA status0x%08x host status0x%08x.

ROMMON has reported a fatal condition during boot up. It may be caused by outdated ROMMON/FPGA images or defected hardware.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLUGIN-3-NOPORT

3-Error

[chars]: Failed to open IPC port.

PLIM client IPC port has not been initialized.

spa-ser-infra

show ipc status

SPA_PLUGIN-3-ALLOC_ERR

3-Error

[chars]: Failed to allocate memory

Failed to allocate the required memory for the data

spa-infra

show ipc status

SPA_CCB-3-CMDFAIL_0ARG

3-Error

[chars]: host command [dec] error: [chars].

A command from host failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMDFAIL_1ARG

3-Error

[chars]: host command [dec]arg0=[dec] error: [chars].

A CCB command failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMDFAIL_2ARG

3-Error

[chars]: host command [dec]arg0=[dec] arg1=[dec] error: [chars].

A command from host failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMDFAIL_3ARG

3-Error

[chars]: host command [dec]arg0=[dec] arg1=[dec] arg2=[dec] error: [chars].

A command from host failed to execute for the given reason.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-CMD_TOOEARLY

3-Error

[chars]: host command [dec] received before handler ready.

Host command comes before handler is initialized

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-ENQUEUE_FAIL

3-Error

[chars]: host command [dec] failed to enqueue.

An error occurred while the SPA console was attempting to enqueue a host command to command queue.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-3-IF_CONFIG

3-Error

[chars]: IF_CONFIG type [dec] failed.

Interface configuration type not valid for SPA card.

-

LOG_STD_SH_TECH_ACTION

SPA_CCB-4-BADENCAP

4-Warning

[chars]: Unknown encapsulation command [dec].

An invalid encapsulation command is received by SPA. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SPA_MIB-4-DATA_LEN

4-Warning

[chars]: MIB message lengths mismatch[chars] expecting [dec] bytes receiving [dec].

MIB updates expect more data than received.

spa-ser-infra

LOG_STD_SH_TECH_ACTION

SPA_PLIM-4-EXCEPTION

4-Warning

[chars] has experienced an exception: [chars]. Writing SPA crash dump information to [chars].

The local CPU in the specified slot indicated in the message has experienced the exception condition. The process that caused the exception might have been restarted. If an exception core dump was created core dump is stored in the SIP flash if available.

-

"If the system continues running normally no action is required. " "If this message recurs or system behaves abnormally please " "collect the crash dump file from SIP flash capture the output of " "the <CmdBold>show hw-module slot/subslot tech-support<NoCmdBold> " "command and open a case with the Technical Assistance Center via " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl."

SPA_PLIM-3-FW_RELOAD

3-Error

[chars] is being reloaded due to firmware/application exception.

Firmware application failed at SPA. The SPA is being reloaded to recover its operational state.

spa-ser-infra

"Collect the application core file from flash. Core file name is " "shown in the preceding message with timestamp."

SPA_PLIM-5-RECEIVINGFILE

5-Notice

Receiving [chars] from [chars] and storing to [chars].

SPA has sent a file syslog or core dump to RP and

-

LOG_STD_DBG_ACTION

SPA_PLIM-3-HEARTBEAT

3-Error

[chars] has experienced an heartbeat failure. Current Sequence [dec] Received Sequence [dec] Time since last keep [dec]ms.

The IPC communication between local CPU and host in the specified slot indicated in the message is not functional. The IPC module will be restarted. Following which communication might be re-established. If the problem persists the SPA will be reset.

-

"If the system continues running normally no action is required. " "If this message recurs or system behaves abnormally please " "collect the logs from the systemRP/SIP. Capture the output of "

SPA_PLIM-3-INITFAIL

3-Error

[chars] has failed initialization because SPA [chars].

A failure occurred during the SPA initialization. SPA is not functional and may be restarted by RP or SIP.

-

"If the SIP or RP successfully initialized the SPA " "no action is required. If the SPA was not successfully " "initialized " LOG_STD_ACTION

SPA_PLIM-3-INIT_PORT

3-Error

[chars] PLIM client IPC port has not been initialized.

-

spa-ser-infra

show ipc status

SPA_PLIM-3-FATALERROR

3-Error

SPA in slot [dec] bay [dec] experienced a fatal error [chars] and is being reset.

A fatal error was encountered during SPA operation. The SPA may be restarted.

-

"If the error is not observed more than once it might be " "a one off event and the SPA needs to be monitored. " "If the issue occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-4-SBE_ECC

4-Warning

[chars] reports [dec] SBE occurance at [dec] addresses

SPA has reproted single bit correctable ECC errors.

spa-ser-infra

"The log shows more than 1 SBE has occurred. " "SBEs are correctable memory problems. It will not affect router operation." "Excessive occurances indicate potential memory defections. Standard " "action is to watch at first occurance and replace at the first chance " "when recurs."

SPA_PLIM-4-SBE_OVERFLOW

4-Warning

[chars] SBE table[dec] elements overflows.

SPA has reproted more unique single bit correctable ECC errors than the platform defined internal table can hold.

spa-ser-infra

"Replace the fault memory chip at the earliest " "chance. SBEs are correctable memory problems. It will not affect router " "operation. Excessive occurances indicate potential memory defections."

SPA_PLIM-3-FILEFORWARD_FAIL

3-Error

[chars] failed to transfer a file from SPA to router flash due to IPC [chars].

A file transfer failed due to IPC errors. The file has not been stored in the flash.

spa-ser-infra

"Check flash disk for empty storage space. If it " "is short of space remove some files from the flash. If the message " "occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-3-FILECREATE_FAIL

3-Error

NULL

Check router and make sure it has installed removable flash card or disk e.g. <CmdArg>disk0:<NoCmdArg> <CmdArg>disk1:<NoCmdArg> <CmdArg>slot0:<NoCmdArg> etc.. If the flash is present make sure

spa-ser-infra

"Check router removable disk and make sure it has empty " "storage space. If the flash disk is short of space remove some files from " "the flash. If the message occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-3-FILE_NOTSTORED

3-Error

NULL

This error is seen when storing a file for a SPA to router removable flash failed. The partial file is removed from router removable flash.

spa-ser-infra

"If the error message occurs repeatedly " LOG_STD_ACTION

SPA_PLIM-3-SW_ERROR

3-Error

NULL

-

spa-ser-infra

LOG_STD_ACTION

SPA_PLIM-3-ERRMSG

3-Error

[chars] [chars]

The error message in parentheses was logged by the SPA.

-

SPA_STD_SH_TECH_ACTION

SPA_DATABUS-3-SPI4_UNALIGNED_BURST

3-Error

[chars] [chars] - An error on the data bus has occurred.

In normal situation transitions from the Data Burst state to payload control or idle control are possible only on integer multiples of 8 cycles or upon end of packet. This error could happen if the MW bit flips on the bus with coincidental good dip4 or due to a misbehaving source.

spa-infra

"Power down and reseat the card. " SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SINGLE_DIP4_PARITY

3-Error

[chars] [chars] - A single DIP4 parity error has occurred on the data bus.

A single parity error has occurred on the data bus between the SPA and the SIP. When this condition is occurring a short duration of packet loss and/or symptoms resulting from data corruption may occur. This condition may indicate a developing hardware failure. This error should occur very infrequently during normal operation and should not occur when no changes are made to the configuration.

spa-infra

"Power down and reseat the interface card. " SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_OUT_OF_FRAME

3-Error

[chars] [chars] - A data bus out of frame error condition has occurred

An error has occurred on the data bus between the SPA and the SIP. When this condition is occurring the interface will be down and/or not forward any traffic.

spa-infra

"Power down and reseat the card. " SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SEQUENCE

3-Error

[chars] [chars] - A sequence error has occurred.

A sequence error has occurred on the data bus between the SPA and the SIP. When this condition is occurring a short duration of packet loss may be noticed. This condition may indicate a developing hardware failure. This error should occur very infrequently during normal operation and should not occur when no changes are made to the configuration.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-PACKET_GAP_ERROR

3-Error

[chars] [chars] - A packet gap error has occurred

The data bus interface on this line card is experiencing a hardware-related issue. No loss of data or data corruption should occur. Packets should continue to be forwarded.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SINGLE_DIP2_PARITY

3-Error

[chars] [chars] - A single DIP 2 parity error on the FIFO status bus has occurred.

The data bus interface on this line card is experiencing a hardware-related issue. Some packets may be dropped.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_FIFO_STATUS_BUS

3-Error

[chars] [chars] - FIFO status bus out of frame condition has occurred.

The data bus interface on this line card is experiencing a hardware-related issue. When this condition is occurring the interface will be down and/or not forward any traffic.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_BAD_CHAN_NUM

3-Error

[chars] [chars] - An error condition on the SPA data bus has occurred.

An error condition on the SPA data bus has occurred. This condition can be caused by a software fault only.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_DATABUS-3-SPI4_CALENDAR_LEN

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. This condition results from a software fault.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_DATABUS-3-SPI4_CRTL_WD_NO_DIP4

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

This message points to an error condition on the SPA data bus. Symptoms of this error include data corruption and/or a short duration of data loss.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_BAD_CNTR_WORD

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. Symptoms of this error include data corruption and/or a short duration of data loss. In addition the interface may lock up.

spa-infra

SPI4_STD_ACTION

SPA_DATABUS-3-SPI4_SINK_FIFO_OVERFLOW

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. Possible causes include misconfiguration of Maxburst parameters incorrect FIFO sizing or FIFO threshold settings.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_DATABUS-3-SPI4_SINK_FIFO_UNDERRUN

3-Error

[chars] [chars] - An error condition on the data bus between the SPA and the SIP has occurred.

An error condition on the data bus between the SPA and the SIP has occurred. Possible causes include misconfiguration of Maxburst parameters incorrect FIFO sizing or FIFO threshold settings.

spa-infra

SPI4_BUGTOOLKIT_ACTION

SPA_EEPROM-4-DATA_TRUNCATED

4-Warning

[chars]: Data will be truncated for field type 0x[hec] - size [dec] bytes too

The provided data to be written into the indicated field type of SPA EEPROM is too big and the data will be truncated in order to fit into the allowed space.

spa-infra

"Retry the operation again with a data size that will fit into the " "indicated size for the field type."

SPA_EEPROM-4-CANNOT_UPDATE

4-Warning

[chars]: EEPROM data cannot be updated at this moment because the SPA is not in service.

The EEPROM update operation cannot be performed because the indicated SPA could have been in \out of service\ state \admin down\ state or is trying to get initialized.

spa-infra

"Retry the operation when the SPA is in service. The operational status " "of the SPA can be checked with the <CmdBold>show hw-module subslot" "<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg> <CmdBold>oir<NoCmdBold> " "command. If the SPA is shown in \"out of service\" state correct the " "indicated problem before the retry to update EEPROM. If the state shown " "is in \"admin down\" re-enable the SPA with <CmdBold>no hw-module " "subslot<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg> <CmdBold>shutdown" "<NoCmdBold> command."

SPA_EEPROM-3-RPC_FAILED

3-Error

Failed to send RPC message to [chars] EEPROM of [chars] in [chars] - [chars]

System failed to send a RPC message to read/write the EEPROM of the indicated SPA. The cause of the error condition is shown in the error message.

-

SPA_EEPROM_STD_RESOURCE_ACTION

SPA_EEPROM-3-READ_FAILED

3-Error

Failed to read the EEPROM content of [chars] in [chars] offset=0x[hec] num_byte=[dec]

System failed to read the EEPROM content of the indicated SPA with the specified offset value and number of bytes to read.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-WRITE_FAILED

3-Error

Failed to write the EEPROM content for [chars] in [chars] offset=0x[hec] num_byte=[dec]

System failed to write data into the EEPROM of the indicated SPA with the specified offset value and number of bytes to write.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-SET_WR_PROTECT_FAILED

3-Error

[chars]: Failed to [chars] the EEPROM write protect mode on [chars].

System failed to enable/disable the write protect mode for SPA EEPROM on the indicated device. This might happen if the device were busy performing other tasks.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-FIELD_NOT_FOUND

3-Error

[chars]: Failed to find content of field type 0x[hec] with data size = [dec] bytes. The EEPROM might require an update.

System failed to find the content of the indicated field type from the SPA EEPROM. The format of the EEPROM of the indicated SPA might not be up to date.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-FORMAT_ERROR

3-Error

[chars]: [chars]. The EEPROM might require an update.

A format error has been detected in the EEPROM of the indicated SPA. The type of error is indicated in the error message.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-SW_ERROR

3-Error

NULL

-

spa-infra

LOG_STD_ACTION

SPA_CONSOLE-3-NOBUF

3-Error

No packet buffer available for sending SPA console messages

An error occurred while the SPA console was attempting to acquire a packet buffer from the IPC buffer pool.

-

show ipc status

SPA_CONSOLE-5-CANTSEND

5-Notice

Cannot send SPA console messages.

An error occurred while a SPA console message was being sent via the IPC. This condition might result in a malfunction in the operation of the IPC.

-

show ipc status

SPA_CONSOLE-5-CANTGET

5-Notice

Cannot get SPA client IPC port

SPA console sub-block is not initialized properly.

-

LOG_STD_ACTION

SPA_CONSOLE-5-CANTSET

5-Notice

Cannot set SPA client IPC port.

SPA console sub-block is not initialized properly.

-

LOG_STD_ACTION

SPA_CONSOLE-3-INITFAIL

3-Error

[chars]: SPA console initialization error: [chars].

A failure occurred during initialization of the SPA console subsystem. The SPA console may not be functioning.

-

LOG_STD_ACTION

SPA_CONSOLE-3-BADDETACH

3-Error

SPA console session detach failed with IPC error [chars].

A failure occurred when attempting to detach SPA console subsystem.

-

LOG_STD_ACTION

SPA_CONSOLE-5-QUEUEFULL

5-Notice

Queue holding SPA console messages is full current console packet will be dropped

An error occurred while the SPA console was Queueing a packet for transmission. Some console data may be lost

-

show ipc status

SPA_CONSOLE-3-TX_BUS_PARAM

3-Error

[chars]: VCON_SPACP: Invalid SPA bus parameters.

There was an error sending a message to SPA.

c7600-ssc-600

LOG_STD_RECUR_ACTION

SPA_CONSOLE-3-RX_BUS_PARAM

3-Error

[chars]: VCON_SPACP: Invalid SPA bus parameters.

There was an error receiving a message from SPA.

c7600-ssc-600

LOG_STD_RECUR_ACTION

SPA_CONSOLE-3-NO_DRIVER

3-Error

[chars]: VCON_SPACP: Driver not ready.

SPA sent a message before SIP was fully initialized.

c7600-ssc-600

LOG_STD_RECUR_ACTION

SPA-3-BAD_FCITYPE

3-Error

[chars]: Illegal FCI type [dec].

An invalid FCI type is passed to SPA. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SPA-3-INITFAIL

3-Error

Initialization error

A failure occurred during the initialization.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-ENTITY_INITFAIL

3-Error

SPA entity initialization error

A failure occurred during the SPA entity management subsystem startup. Entity management is not enabled.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-SW_ERROR

3-Error

NULL

-

spa-infra

LOG_STD_ACTION

SPA-3-ENVMON_INITFAIL

3-Error

SPA environmental monitoring initialization error

A failure occurred during the SPA environmental monitoring subsystem startup. Environmental monitoring is not enabled.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-ENVMON_NOT_MONITORED

3-Error

Environmental monitoring is not enabled for [chars]

The indicated SPA has not registered any sensors with the environmental monitoring system.

-

LOG_STD_SH_TECH_ACTION

SPA-4-TEMP_WARNING

4-Warning

[chars] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-2-TEMP_CRITICAL

2-Critical

[chars] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP Please correct immediately.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-0-TEMP_SHUTDOWN_OVR

0-Emergency

[chars] temperature too high on sensor [dec] [dec]C but shutdown has been

MSG_SPA_TEMP_HIGH_EXP SPA shutdown has been overridden by configuration

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-0-TEMP_SHUTDOWN

0-Emergency

[chars] temperature too high on sensor [dec] [dec]C. SPA has been shut down.

MSG_SPA_TEMP_HIGH_EXP The SPA has been shut down.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-4-TEMP_WARNLOW

4-Warning

[chars] temperature too low on sensor [dec] [dec]C.

SPA temperature too low. Component reliability and data integrity may be compromised.

-

"Raise the ambient temperature if it is too low. If there is no " "issue with the ambient temperature then the SPA temperature sensor has " "likely failed. If there are no data errors this warning can be " "ignored."

SPA-4-POWER_WARNING

4-Warning

[chars] power consumption [dec] Watts is higher than typical max value of [dec] Watts.

SPA power consumption is higher than the typical max value. Component reliability and data integrity may be compromised.

-

"Check for the total power available for the system. If " "there is sufficient power availabe this condition may not have " "any adverse affects."

SPA-2-VOLT_CRITICAL

2-Critical

[chars] voltage outside of nominal range. Nominal [dec]mV value[dec]mV

MSG_SPA_VOLT_EXP_COMMON

-

MSG_SPA_VOLT_ACTION_SCHED_REPLACE

SPA-2-VOLT_SHUTDOWN_OVR

2-Critical

[chars] voltage outside of operating range. Nominal [dec]mV value[dec]mV.

MSG_SPA_VOLT_EXP_COMMON

-

MSG_SPA_VOLT_SCHED_REPLACE

SPA-0-VOLT_SHUTDOWN

0-Emergency

[chars] voltage out of operating range. Nominal [dec]mV value [dec]mV.

MSG_SPA_VOLT_EXP_COMMON The SPA has been shut down to prevent component damage.

-

"Replace the SPA immediately. " "Record the associated messages and return the SPA for service."

SPA_HA-3-BADSWITCHOVER

3-Error

[chars]: Invalid HA event detected: [chars]

HA switch over event comes before finishing inialization.

-

LOG_STD_SH_TECH_ACTION

ASR1000_SPA_ETHER_DAMSELFLY-3-PLIM_QOS

3-Error

Interface [chars] failed to apply PLIM QOS [chars] value = 0x%X

Attempt to apply the configured input classification for the specified interface failed

asr1k-io-internal

"This indicates an internal software failure"

ASR1000_SPA_ETHER_DAMSELFLY-3-UNSUPPORTED_XCVR

3-Error

Transceiver type [chars] is not allowed on spa [chars] port [dec]

This transceiver is not allowed on the SPA

asr1k-io-internal

"Consult the documentation and ensure supported " "transceivers and plugged into the SPA"

ASR1000_SPA_ETHER_LC-3-NP_HW_SW_MISMATCH

3-Error

The hardware and software copies of NP client do not match. This indicates reconciliation failure.

During reconcilation phase of Minimal Disruptive Restart it is found that the software and hardware copies of a register in phy do not match. This indicates an error and the SPA will be reset as normal and impact traffic.

asr1k-ether-lc

"Open a case with Cisco Technical Assistance Center for further " "assistance"

ASR1000_SPA_ETHER_LC-3-PHY_HW_SW_MISMATCH

3-Error

The hardware and software copies of a register in the phy for port [dec] do not match. This indicates reconciliation failure.

During reconcilation phase of Minimal Disruptive Restart it is found that the software and hardware copies of a register in phy do not match. This indicates an error and the SPA will be reset as normal and impact traffic.

asr1k-ether-lc

"Open a case with Cisco Technical Assistance Center for further " "assistance"

SPA_GE_DWDM-3-DWDM_ERROR

3-Error

[chars]

SPA driver detected an error in the DWDM init routine

spa-eth-10ge

"The SPA driver has detected problem with DWDM init routine." "If the ports on the SPA are not operating as expected power down and" "reseat the indicated SPA card. " "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_GE_DWDM-3-NULL_DATA_STRUCTURE

3-Error

[chars] [dec] [dec]

The SPA driver detected NULL data during DWDM initialization

spa-eth-10ge

"Reload the SPA card and if the problem " "persists contact your technical support representative"

SPA_GE_DWDM-3-PLL_NOT_LOCKED

3-Error

[chars] not locked after \ [dec] retries [hex]

The SPA driver failed to initialize the PLL

spa-eth-10ge

"The SPA driver has detected problem with DWDM init routine." "If the ports on the SPA are not operating as expected power down and" "reseat the indicated SPA card. " "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_GE_DWDM-3-MALLOC_FAILED

3-Error

[chars]

The SPA driver detected a memory error on the SPA card

spa-eth-10ge

"Reload the card and if the problem " "persists call the TAC"

SPA_GE_DWDM-3-UT2_SPA

3-Error

[chars]

The SPA driver did not detect a UT2 transponder module

spa-eth-10ge

"Check if the SPA is a DWDM SPA before " "executing the command"

SPA_GE_DWDM-3-SFP_DETECT

3-Error

[chars]

The SPA driver did not detect a Cu-SFP for the port

spa-eth-10ge

"Please plugin a CISCO compliant SFP in the " "corresponding port and retry the command"

ETH_SPA_MAC-3-UNREC_ECC_ERR

3-Error

[chars] : An unrecoverable ECC error occured in the MAC

An unrecoverable ECC error occured in the MAC.

spa-eth-all

"Try to reload the SPA to recover from the failure. If the problem " "persist contact Cisco Technical Assistance Center for assistance."

ETH_SPA_MAC-3-SPI4_ERROR

3-Error

[chars] : SPI4 Error occured in the MAC

SPI4 error occured in the MAC.

spa-eth-all

"SPI error reported in the SPA. Try reseating the SPA if the error " "occurs multiple times. If you further need assistance please open a " "case with Cisco TAC at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl"

ETH_SPA_MAC-3-SPI4_SINK_INIT_ERR

3-Error

[chars] : Marvel spi4.1 sink init failed PL410 global status <lock> not set

An internal SPI4 error occurred in the SPA.

spa-eth-all

"If the issue persists return the SPA using the RMA process."

ETH_SPA_MAC-3-RECONFIG_FAILURE

3-Error

MAC reconfiguration failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart a mac reconfiguration error has occured.This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_MAC-3-PHY_RECONFIG_FAILURE

3-Error

PHY reconfiguration failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart. This indicates an error and the SPA will be reset as normal and impact traffic.

-

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_MAC-3-RESTART_FAILURE

3-Error

MAC restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart mac restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_MAC-3-PHY_RESTART_FAILURE

3-Error

PHY restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart phy restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-SPI4_SYNC_FAIL

3-Error

[chars] : Sync check failed in [chars] SPI4 interafce

Synchronization check failed in the Gila/Fugu SPI4 interafce

spa-eth-all

"Try reseating the SPA. If the issue persists contact Cisco Technical " "Assistance Center."

ETH_SPA_GILA_FUGU-3-SPI4_RDOOF_ERR

3-Error

[chars] : [chars] Rdata Out of Frame error

An internal SPI4 error SPI4 Rdata Out of Frame error occured in

spa-eth-all

"If the issue persists open a case with the Cisco Technical Assistance " "Center."

ETH_SPA_GILA_FUGU-3-SPI4_OVF_ERR

3-Error

[chars] : [chars] Overflow Error

An internal SPI4 error SPI4 Overflow Error occured in the SPA.

spa-eth-all

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-SPI4_MCALPRTY_ERR

3-Error

[chars] : [chars] Calender memory Parity error

An internal SPI4 error SPI4 calender memory parity error occurred

spa-eth-all

"If the issue persists it may be a case of bad hardware. Please open " "a case with Cisco technical support personnel for further assistance."

ETH_SPA_GILA_FUGU-3-SPI4_MCALRBPRTY_ERR

3-Error

[chars] : [chars] Calender memory read back Parity error

An internal SPI4 error SPI4 Calender memory read back parity error

spa-eth-all

"Try reseating the SPA and if the issue persists open a case with the " "Cisco Technical Assistance Center."

ETH_SPA_GILA_FUGU-3-SPI4_MDATAPRTY_ERR

3-Error

[chars] : [chars] Memory Parity error

An internal SPI4 error SPI4 DATA FIFO Memory Parity error

spa-eth-all

"If the issue persists open a case with Cisco Technical Assistance " "Center for further assistance."

ETH_SPA_GILA_FUGU-3-SPI4_MCNTPRTY_ERR

3-Error

[chars] : [chars] Memory Parity error

An internal SPI4 error SPI4 Control FIFO Memory Parity error

spa-eth-all

"If the issue persists open a case with Cisco Technical Assistance " "Center for further assistance."

ETH_SPA_GILA_FUGU-3-VLAN_TCAM_ERR

3-Error

TCAM programming error at offset [dec]

An error was encountered when programming the VLAN TCAM. Two tcam entries are seen to have the same logical address so traffic drop will be seen on these subinterfaces

spa-eth-all

"Reload the Linecard. If the issue persists please " "open a case with Cisco TAC for further assistance."

ETH_SPA_MAC-6-INTR_BURST

6-Information

Interrupts from [chars] have crossed burst limit of [dec] in [dec] msec for port [dec]/[dec]/[dec]

Interrupts that have crossed the burst limit are detected by the SPA.

spa-eth-all

"Check the interface configuration and receive signal characteristics. " "Also verify the XFP transceiver and receive signal path. " "Re-enable the interface after corrective action."

ETH_SPA_MAC-3-INTR_MAX_BURST

3-Error

Bursts of interrupts from [chars] have crossed maximum limit [dec] for port [dec]/[dec]/[dec]

Burst of interrupts that have crossed the maximum limit are detected by the SPA.

spa-eth-all

"Check the interface configuration and receive signal characteristics. " "Also verify the XFP transceiver and receive signal path. " "Re-enable the interface after corrective action."

ETH_SPA_GILA_FUGU-3-DATA_VER_MISMATCH

3-Error

TCAM checkpointed data version [dec] differs from current version [dec].

During Minimal Disruptive Restart version of checkpointed tcam data is found to be different from the data in the current version. The SPA will be reset as normal and hence will impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-HDR_VER_MISMATCH

3-Error

TCAM checkpointed header version [dec] differs from current version [dec].

During Minimal Disruptive Restart version of checkpointed tcam header is found to be different from the header in the current version. The SPA will be reset as normal and hence will impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-HDR_PARAMS_MISMATCH

3-Error

TCAM checkpointed header values differs from values in current version.

During Minimal Disruptive Restart values of fields in the checkpointed tcam header is found to be differnt from the values in the current version of IOS. The SPA will be reset as normal and hence will impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-ELT_NOT_IN_CUR_VER

3-Error

The element at address [dec] in [chars] tcam is found missing during Minimal Disruptive Restart reconcilation.

During the reconcilation phase of Minimumal Disruptive Restart an element was found to be present in the old IOS but not present in the new IOS image. This indicates that the config for this element was not played down from the RP during config-replay. This is an error condition and the SPA will be reset as normal and hence will impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance"

ETH_SPA_GILA_FUGU-6-ELT_IS_NEW

6-Information

The element at address [dec] in [chars] tcam is found to be new during Minimal Disruptive Restart reconcilation.

During the reconcilation phase of Minimumal Disruptive Restart an element was found to be present in the new IOS but not present in the old IOS image. This is not an error condition the SPA driver will program this new entry into the hardware.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance"

ETH_SPA_GILA_FUGU-3-HW_SW_MISMATCH

3-Error

The hardware and software copies of the element at address [dec] in tcam [chars] do not match. This indicates reconcilation failure.

During reconcilation phase of Minimal Disruptive Restart it is found that the software and hardware copies of an element in tcam do not match. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance"

ETH_SPA_GILA_FUGU-3-RECONFIG_FAILURE

3-Error

Fugu reconfiguration failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart fugu reconfiguration error has occured. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-TCAM_RECONFIG_FAILURE

3-Error

Fugu TCAM reconfiguration failed for SPA in slot [dec] bay [dec] with error [dec] reconfig_needed [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart fugu tcam reconfiguration error has occure. This indicates an error and SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-RESTART_FAILURE

3-Error

Fugu restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart fugu restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GILA_FUGU-3-TCAM_RESTART_FAILURE

3-Error

TCAM restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart fugu tcam restart has failed. This indicates an error and SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_SERDES-3-RECONFIG_FAILURE

3-Error

Serdes reconfiguration failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart serdes reconfiguration error has occured. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_SERDES-3-RESTART_FAILURE

3-Error

Serdes restart failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart.

During Minimal Disruptive Restart serdes restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic.

spa-eth-v2

"Open a case with Cisco Technical Assistance Center for further " "assistance."

ETH_SPA_GEN-3-CU_SFP_NOT_SUPP

3-Error

CU-SFP is not supported on SPA-2x1GE-V2 / SPA-2x1GE-SYNCE

CU-SFP is not supported on SPA-2x1GE-V2 / SPA-2x1GE-SYNCE

spa-eth-all

"Use PHY based ports for CU Connections "

SYNCE_SPA_INFO-6-NETSYNC_UNCONF_SOURCE

6-Information

CLOCK LOCK is [chars] for [chars] interface which is not selected as source to synchronize chassis.

INFORMATION Message: CLOCK LOCK is Cleared/Asserted for interface which is not configure as a source

spa-synce-all

"No further action required. This is source monitor " "INFORMATION message not an error Message."

MN_SPA_PTP-6-CONFIG_CHANGE

6-Information

Change in ToP configuration on [dec]/[dec]. This will result \n\ into Termination of all existing PTP sessions on [dec]/[dec].

To take effect of new/changed configuration requrie \n\ restart of PTP session

spa-synce-all

"No further action required. This is an \n\ INFORMATION message not an error Message."

MN_SPA_PTP-3-SEMAHOG

3-Error

SEMAHOG by SPA [chars] Process holding Sema is [chars]

SEMAPHORE LOCK ERROR

spa-synce-all

" Remove the config which caused this"

MN_SPA_PTP-4-PTP_CLOCK_MODE

4-Warning

SPA [dec]/[dec] is working in PTP SLAVE or Boundary mode external clock on BITS port would be PTP recovered clock

Info regarding external clock in PTP slave mode

spa-synce-all

"No further action required. This is an\n\ INFORMATION message not an error Message."

MN_SPA_PTP-6-SPLL_STATE_CHANGE

6-Information

Recovered clock in [dec]/[dec] status changed to [chars]

Recovered clock status change info

spa-synce-all

"No further action required. This is an \n\ INFORMATION message not an error Message."

MN_SPA_PTP-3-GMII_LINKUP_DOWN

3-Error

GMII Links are [chars] and [chars] for ports 1 and 2 respectively on the SPA.

Error Message: GMII link status has changed on the SPA.

spa-synce-all

"OIR the SPA to recover from the error."

ETH_SPA_GEN-3-UNSUPPORTED_XCVR

3-Error

Transceiver type GLC-GE-100FX is not supported on SPA-8xGE-V2

Transceiver type GLC-GE-100FX is not supported on SPA-8xGE-V2

spa-eth-all

"Consult the documentation and ensure supported " "transceivers are plugged into the SPA"

MN_SPA_PTP-3-BITS_CLOCK

3-Error

[chars] : SPA bits transmit clock has encountered error : 0x[hec] .\n

Error message regarding BITS transmit clock failure

spa-synce-all

"OIR the SPA if the error is consistent"

SPA_FPD-6-IMG_CORRUPTION

6-Information

[chars]: FPD image corruption detected for \[chars]\ ID=[dec] forcing upgrade

The software detected corruption on a FPD image and it is triggering the FPD automatic upgrade mechanism to correct the problem.

spa-infra-fpd

"No Action is required."

SPA_FPD-4-UPGRADE_ABORTED

4-Warning

[chars]: Upgrade aborted for \[chars]\ ID=[dec] - [chars]

The upgrade operation for the FPD image was aborted because the provided image cannot be used by the driver to perform the image programming operation.

spa-infra-fpd

"Make sure that the provide FPD image package for " "the FPD upgrade operation is a valid one for the Cisco IOS release in " "use. This can be verified with the <CmdBold>show upgrade fpd package " "default<NoCmdBold> command to display the required FPD image package " "version for the IOS image."

SPA_FPD-3-GETVER_FAILED

3-Error

[chars]: Failed to get FPD version for \[chars]\ ID=[dec]: [chars].

Failed to get FPD version due to either IPC problem or operation error. The card will be disabled.

spa-infra-fpd

"Check SPA seating and SPA status. " "Ensure compatibility among FPD IOS and possible SPA " "firmware by comparing output of command " "<CmdBold>show hw-module subslot fpd<NoCmdBold> with IOS " "Release Notes. Obtain IOS version by command " "<CmdBold>show version<NoCmdBold>."

SPA_FPD-3-UPGRADE_FAILED

3-Error

[chars]: Failed to upgrade FPD [chars].

The FPD image upgrade operation failed. This error is specific to the SPA. The cause could be a wrong image file error in accessing fpga storage physical interrupt such as power failure or card removal. Depending on SPA type and error cause the card could be in an unusable status. Normally the system automatically reattempts the upgrade and shuts the card after repeated failures.

spa-infra-fpd

"Do not interrupt the system while an FPD " "upgrade is in progress. Obtain the matching FPD package. Refer " "to IOS Release Notes for more information on obtaining the correct " "FPD package for the SPA. Review the output of the RP FPD logs."

SPA_FPD-3-JTAG_ERR

3-Error

[chars]: Failed to program a [chars] FPD image file. Error code 0x%02x.

While attempting to program a SPA FPGA via JTAG bus an error occurs. It could be caused by an outdated carrier card FPGA or SPA connection. It may also flag an internal software error.

spa-infra-fpd

"Retry the upgrade after reseating SPA. " "Verify carrier card FPGA is current. Copy exact the error " "message and report to TAC."

SPA_FPD-3-SW_ERROR

3-Error

NULL

-

spa-infra-fpd

LOG_STD_ACTION

SPA_FPD-3-PWR_OFF_FAILED

3-Error

Failed to power-off [chars] in [chars] for FPD offline upgrade within [dec] seconds.

The power-off operation of the indicated SPA failed within the number of specified seconds. This might indicate that the time used to wait for SPA to power-off is not long enough which can happen if the SPA has a lot of interfaces configured.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the upgrade operation."

SPA_FPD-3-SMM665_CONF_WRITE_ERROR

3-Error

[chars]: Failed to write new configuration into SMM665 device.

The write operation to SMM665 is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the upgrade operation."

SPA_FPD-3-ADM106X_READ_VER_ERROR

3-Error

[chars]: Failed to read version info from ADM106x device - [chars]

The read operation to ADM106x is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Try to reload the SPA with <CmdBold>hw-module subslot<NoCmdBold> " "<CmdArg>slot#/subslot#<NoCmdArg> <CmdBold>reload<NoCmdBold> command " "to correct the failure. If problem persists move the SPA to another " "bay of the carrier card."

SPA_FPD-3-IHEX_PARSE_ERROR

3-Error

NULL

-

spa-infra-fpd

LOG_STD_ACTION

SPA_FPD-3-ADM106X_EEPROM_READ_ERROR

3-Error

[chars]: Failed to read the content of ADM106x [chars] EEPROM section - [chars]

The read operation to ADM106x is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Retry the same operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the operation."

SPA_FPD-3-ADM106X_EEPROM_WRITE_ERROR

3-Error

[chars]: Failed to write new configuration into ADM106x [chars] EEPROM section - [chars]

The write operation to ADM106x is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the upgrade operation."

SPA_FPD-3-ADM106X_EEPROM_VERIFY_ERROR

3-Error

[chars]: Verification of write operation failed in ADM106x [chars] EEPROM section for address 0x[hec] - read value '0x[hec]' expected value '0x[hec]'.

The verification of the write operation has found a mismatch on the EEPROM data. The problem might be an indication of aging effect on the device that cannot longer hold written data.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists replace the SPA."

SPA_FPD-2-PWR_NO_OK

2-Critical

SPA POWER OK signal is not asserted for [chars] in [chars] for FPD upgrade.

The check for SPA POWER OK signal assertion failed. This might indicate a HW problem with the SPA.

spa-infra-fpd

"Contact your Cisco technical support " "representative to have the SPA replaced."

DSP_SPA-2-INITFAIL

2-Critical

Not Enough Resources:[chars]

The shared port adaptor failed to complete software initialization.

SPA-DSP

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DSP_SPA-3-BUFF_FAIL

3-Error

Not Enough MEM Buffers [chars]

Not enought memory buffers for shared port adaptor operation.

SPA-DSP

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DSP_SPA-3-FILE_OP_FAIL

3-Error

Failed to open file [chars] : [chars]

Failed to open file

SPA-DSP

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DSP_SPA-3-FILE_RD_FAIL

3-Error

Failed to read [dec] bytes from file: [chars]

Failed to read data from file

SPA-DSP

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DSP_SPA-3-NULL_FAIL

3-Error

Non-Initialized ptr: [chars]

About to Access non-initialized pointer

SPA-DSP

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

DSP_SPA-3-HW_ERROR

3-Error

[chars]: A Hardware device error was detected. Trying to recover the SPA by reload. Error information : [chars]

An internal hardware device error has occurred on the services SPA. The error message indicates the slot subslot the SPA type and the name of the hardware device. The SPA has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the SPA will be made. This message is likely due to an unrecoverable hardware failure.

spa-dsp

"Perform OIR of the SPA located in the specified subslot. Before removing " "the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command. " "Remove the SPA wait 5 seconds and reinsert the SPA. If " "the problem persists copy the error message text exactly as it appears " "on the console or in the system log enter the <CmdBold>show diag" "<NoCmdBold> command contact your Cisco technical support representative " "and provide the representative with the gathered information."

DSP_SPA-3-HW_ERROR_INFO

3-Error

[chars]: Non fatal hardware device error was detected. Error information : [chars]

An internal hardware device error has occurred on the services SPA. The error message indicates the slot subslot the SPA type and the name of the hardware device. This message is likely due to a recoverable hardware failure.

spa-dsp

"Perform OIR of the SPA located in the specified subslot. Before removing " "the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command. " "Remove the SPA wait 5 seconds and reinsert the SPA. If " "the problem persists copy the error message text exactly as it appears " "on the console or in the system log enter the <CmdBold>show diag" "<NoCmdBold> command contact your Cisco technical support representative " "and provide the representative with the gathered information."

DSP-5-UPDOWN

5-Notice

DSP [dec] is [chars]

DSP device changed state up/down

-

LOG_STD_NO_ACTION

DSP-5-DNLD

5-Notice

DNLD started for device [dec]

DSP bootloader DNLD starte

-

LOG_STD_NO_ACTION

DSP-3-FIRMWARE_VER_INFO

3-Error

Downloading streamware... for device [dec]. DSP firmwarever:[dec].[dec] contained in image has different version from

DSP firmware version check

-

LOG_STD_NO_ACTION

DSP-3-DSP_DNLD

3-Error

DSP device [dec] DNLD process exited. Trying to recover DSP device by rebooting the DSP

A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device.

spa-dsp

"Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the <CmdBold>hw-module subslot stop<NoCmdBold> command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the <CmdBold>show diag <NoCmdBold> command contact " "your Cisco technical support representative and provide the " "representative with the gathered information."

DSP-3-TIMER

3-Error

[chars] timer expired for DSP [dec]

DSP timer has expired

-

LOG_STD_NO_ACTION

DSP-3-DSP_WATCHDOG

3-Error

DSP device [dec] is not responding. Trying to recover DSP device by reloading

A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device.

spa-dsp

"Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the <CmdBold>hw-module subslot stop<NoCmdBold> command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the <CmdBold>show diag <NoCmdBold> command contact " "your Cisco technical support representative and provide the " "representative with the gathered information."

DSP-3-DSP_ALARM

3-Error

DSP device [dec] is not responding. Trying to recover DSP device by reloading

A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device.

spa-dsp

"Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the <CmdBold>hw-module subslot stop<NoCmdBold> command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the <CmdBold>show diag <NoCmdBold> command contact " "your Cisco technical support representative and provide the " "representative with the gathered information."

DSP-3-DSP_KEEPALIVE

3-Error

DSP device [dec] is not responding. Trying to recover DSP device by reloading

A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device.

spa-dsp

"Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the <CmdBold>hw-module subslot stop<NoCmdBold> command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the <CmdBold>show diag <NoCmdBold> command contact " "your Cisco technical support representative and provide the " "representative with the gathered information."

DSS-5-UPDOWN

5-Notice

DSP core [dec] is [chars]

DSP core changed state up/down

-

LOG_STD_NO_ACTION

DSS-3-ACK_FAIL

3-Error

Ack failed for dsp_id [dec]\n\ seq_no [dec]

DSP core not responding to host messages

-

LOG_STD_NO_ACTION

DSS-3-DSPID_INVALID

3-Error

Invalid DSPID [dec]

Invalid DSP ID detetced in the message

-

LOG_STD_NO_ACTION

DSS-3-TIMER

3-Error

[chars] timer expired for DSPID [dec]

DSS timer has expired

-

LOG_STD_NO_ACTION

CRASH_DUMP-3-FILE_OP

3-Error

FILE operation [chars] failed CRASH DUMP May not be successfull

The File operation for dumping DSP crash details failed The error message could be a software issue or due to not enough disk space.

-

LOG_STD_NO_ACTION

CRASH_DUMP-6-TIMEOUT

6-Information

CRASH DUMP may not be successfull for the device [dec]

Crash dump process timed out waiting for diaganostic messages

-

LOG_STD_NO_ACTION

CRASH_DUMP-6-ABORT

6-Information

CRASH DUMP aborted for device [dec]

Crash dump aborted. Crash Dump may not be successfull

-

LOG_STD_NO_ACTION

SPA_DSPRM-3-DSPALARM

3-Error

Received alarm indication from dsp [dec]/[dec]/[dec].

Operational error detected in DSP.

spa-dsp

"Reload the SPA card and if the problem persists " LOG_STD_ACTION

SPA_DSPRM-5-UPDOWN

5-Notice

DSP [dec]/[dec]/[dec] is [chars]

DSP device changed state up/down

-

LOG_STD_NO_ACTION

SPA_DSPRM-5-RESTART

5-Notice

DSP [dec]/[dec]/[dec] is restarted

DSP device restarted

-

LOG_STD_NO_ACTION

SPA_DSPRM-3-INSUFFICIENT

3-Error

Insufficient memory for [chars]

Insufficient memory for SPA-DSP DSPRM operation

spa-dsp

"Enter the <CmdBold>show memory summary<NoCmdBold> command to attempt to\n\ determine the cause of the error. " LOG_STD_REDUCE_ACTION

SPA_DSPRM-3-DSPALARMINFO

3-Error

[chars]

DSP Alarm Data

spa-dsp

"Reload the SPA card and if the problem persists " LOG_STD_ACTION

FARM_DSPRM-4-NOC5510WARN

4-Warning

dsp service dspfarm can not be configured for this card type.

There is C549 NM-HDV card configured for dspfarm service.\n\ Only one dspfarm card type is allowed.

-

"If C5510 card type dspfarm is desired then remove C549 NM-HDV dspfarm \n\ service and reconfigure dspfarm service for this card. "

FARM_DSPRM-6-CALLDROPINFO

6-Information

dspfarm active calls on this card dsp [dec] channel [dec] will be dropped.

The card has been removed. Dspfarm active calls on this card\n\ will be dropped.

-

"No action is required."

FARM_DSPRM-6-CARDREMOVEINFO

6-Information

dspfarm card slot [dec] is removed.

dspfarm card type is remvoed from the slot.

-

"No action is required."

FARM_DSPRM-6-CARDINSERTINFO

6-Information

dspfarm card slot [dec] is inserted.

dspfarm card type is inserted into the slot.

-

"No action is required."

SPA_SERIAL_IM-3-NULL_DATA_STRUCTURE

3-Error

NULL pointer detected: [chars]

A software error occured and SPA driver is not able to retrieve the data structure mentioned in the message.

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-UNSUPPORTED_DATA

3-Error

common_str_empty_str

A software error occured and SPA driver encounterd unsupported data mentioned in the message

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-UNKNOWN_ENCAP

3-Error

common_str_empty_str

A software error occured and SPA driver encounterd unknown encapsulation mentioned in the message

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-TDL_SEND_FAIL

3-Error

[chars]

Failed to send TDL message.

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-MSG_ENQUEUE_ERROR

3-Error

[chars]

Failed to enqueue a message.

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-DPIDX_LKUP_ERR

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

wolfeisland-sw

LOG_STD_NO_ACTION

SPA_SERIAL_IM-3-VLAN_ID_NONZERO

3-Error

VLAN identifier is not zero before allocation for interface [chars]

The SPA driver is seeing non zero VLAN identifier before allocating new vlan identifier for the interface specified in the message. This indicates a software error.

wolfeisland-sw

LOG_STD_NO_ACTION

SPA_SERIAL_IM-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

The Periodic one second process creation failed. This indicates a software error.

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-UNSUPPORTED_SPA_TYPE

3-Error

Unsupported spa type: [dec]

Failed to create an interface hwidb.

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-SERIAL_SUBBLOCK_ALLOC_FAIL

3-Error

Failed to create serial subblock at : [chars]: [chars]\n

Failed to create serial subblock

wolfeisland-sw

LOG_STD_ACTION

SPA_SERIAL_IM-3-INVALID_TXRX

3-Error

[chars] doesn't support different tx speed [dec] and rx speed [dec]

The software does not support different tx speed and rx speed

wolfeisland-sw

"Configure the tx speed and rx speed to be equivalent."

SPA_SERIAL_IM-3-IM_LIMIT_EXCEEDED

3-Error

The system supports a maximum of two serial Interface Modules. Additional modules will not be operational. Check the output of 'show platform' for details.

Failed to create tty.

wolfeisland-sw

LOG_STD_ACTION

SPA_ETHER-4-NOPROCESS

4-Warning

Subslot [dec]/[dec] [chars] creation of [chars] process failed

The creation of an IOS process to manage the SPA failed. The error message\n\ indicates the modular services card slot the SPA subslot the SPA type and\n\ the name of the process. This error message will be accompanied by an IOS\n\ error message that will give more information about the cause for this\n\ failure.

spa-eth-fe

"Enter the <CmdBold>show memory summary<NoCmdBold> command to attempt to\n\ determine the cause of the error. Reduce system activity to reduce memory\n\ demands. If conditions warrant upgrade to a larger memory configuration.\n\ If you require further assistance " LOG_STD_REDUCE_ACTION

SPA_ETHER-3-INITFAIL

3-Error

Subslot [dec]/[dec] [chars] initialization failure [chars]

The initialization of an internal device on the Ethernet SPA in the\n\ specified subslot has failed. The error message indicates the modular\n\ services card slot the SPA subslot the SPA type and the name of the\n\ device that failed to initialize. The message also provides the interface\n\ name and other details about the error.

spa-eth-fe

"Copy the error message text exactly as it appears on the console or in the\n\ system log enter the <CmdBold>show tech-support<NoCmdBold> command\n\ contact your Cisco technical support representative and provide the\n\ representative with the gathered information."

SPA_ETHER-1-ALLOCFAIL

1-Alert

Subslot [dec]/[dec] [chars] allocation failure [chars]

The router has failed to allocate sufficient memory for a software module\n\ on the Ethernet SPA located in the specified subslot. The error message\n\ indicates the modular services card slot the SPA subslot the SPA type and\n\ the name of the software module.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. Enter\n\ the <CmdBold>show memory summary<NoCmdBold> command to attempt to\n\ determine the cause of the error. Reduce system activity to reduce memory\n\ demands. If conditions warrant upgrade to a larger memory configuration.\n\ If you require further assistance " LOG_STD_REDUCE_ACTION

SPA_ETHER-3-HW_ERROR

3-Error

Subslot [dec]/[dec] [chars] Hardware device error [chars] detected reactivating

An internal hardware device error has occurred on the Ethernet SPA. The\n\ error message indicates the modular services card slot the SPA subslot\n\ the SPA type and the name of the hardware device. The SPA has been\n\ deactivated and reactivated to resolve the problem. If the error occurs\n\ more than five times within an hour no further attempts to reactivate the\n\ SPA will be made. This message is likely due to an unrecoverable hardware\n\ failure

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show diag<NoCmdBold>\n\ command contact your Cisco technical support representative and provide\n\ the representative with the gathered information."

SPA_ETHER-3-SEND_MSG

3-Error

Subslot [dec]/[dec] [chars] Failed to notify driver process about a line state change in one of the SPA interfaces

A line state change has occurred on one of the interface ports on the\n\ Ethernet SPA. The error message indicates the modular services card slot\n\ the SPA subslot and the SPA type. Information to identify which interface\n\ port is affected on the SPA is not available. The affected interface might\n\ not function properly.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. Enter\n\ the <CmdBold>show memory summary<NoCmdBold> command to attempt to\n\ determine the cause of the error. Reduce system activity to reduce memory\n\ demands. If conditions warrant upgrade to a larger memory configuration.\n\ If you require further assistance " LOG_STD_REDUCE_ACTION

SPA_ETHER-3-INVALID_PORT

3-Error

Subslot [dec]/[dec] [chars] Incorrect port number [dec] specified for SPA

An internal error has been encountered by the Ethernet software driver for\n\ the SPA. The error message indicates the modular services card slot the\n\ SPA subslot the SPA type and the invalid interface port number. This\n\ problem is caused by a software caveat.

spa-eth-fe

"Copy the error message text exactly as it appears on the console or in the\n\ system log enter the <CmdBold>show tech-support<NoCmdBold> command\n\ contact your Cisco technical support representative and provide the\n\ representative with the gathered information."

SPA_ETHER-3-SPI4_NOT_IN_SYNC

3-Error

Subslot [dec]/[dec] [chars] SPI4 internal interface is not synchronized with the\n\ modular services card for the SPA located in the specified subslot.

The SPI4 internal path between the modular services card and the SPA is\n\ not synchronized. The error message indicates the modular services card\n\ slot the SPA subslot and the SPA type. This error indicates that either\n\ the SPA is not properly inserted into the MSC or a hardware failure has\n\ occurred on the SPA.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show\n\ tech-support<NoCmdBold> command contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

SPA_ETHER-4-TEMPERATURE_READ_FAIL

4-Warning

Subslot [dec]/[dec] [chars] Failed to read current temperature from sensor [dec] status = 0x[hec]

The current temperature reading on the SPA cannot be determined. The\n\ error message indicates the modular services card slot the SPA subslot and\n\ the SPA type. This error indicates a hardware failure.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show\n\ tech-support<NoCmdBold> command contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

SPA_ETHER-4-VOLTAGE_READ_FAIL

4-Warning

Subslot [dec]/[dec] [chars] Failed to read the current voltage for [chars] supply

The current voltage reading for the SPA voltage supply cannot be\n\ determined. The error message indicates the modular services card slot\n\ the SPA subslot the SPA type and the identification of the voltage supply.\n\ This error indicates a hardware failure.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show\n\ tech-support<NoCmdBold> command contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

SPA_ETHER-4-BAY_NOT_FOUND

4-Warning

Subslot [dec]/[dec] [chars] Failed to get the bay information

Unable to retrieve a software data structure for the subslot. The error\n\ message indicates the modular services card slot the affected subslot and\n\ the SPA type. This error indicates a software caveat.

spa-eth-fe

"Copy the error message text exactly as it appears on the console or in the\n\ system log enter the <CmdBold>show tech-support<NoCmdBold> command\n\ contact your Cisco technical support representative and provide the\n\ representative with the gathered information."

SPA_ETHER-3-TCAM_INST_CREATE_FAIL

3-Error

Subslot [dec]/[dec] [chars] Failed to create the TCAM management instance status = 0x[hec]

The SPA failed to create the internal data structure needed to manage TCAM\n\ entries. The error message indicates the modular services card slot the\n\ SPA subslot and the SPA type. This error indicates a software caveat.

spa-eth-fe

"Copy the error message text exactly as it appears on the console or in the\n\ system log enter the <CmdBold>show tech-support<NoCmdBold> command\n\ contact your Cisco technical support representative and provide the\n\ representative with the gathered information."

SPA_ETHER-3-TCAM_ACCESS_FAILURE

3-Error

Subslot [dec]/[dec] [chars] Failure in accessing the TCAM device [chars] status = 0x[hec]

Access to the TCAM device on the SPA has failed. The error message\n\ indicates the modular services card slot the SPA subslot and the SPA type.\n\ This error indicates a hardware failure.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show\n\ tech-support<NoCmdBold> command contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

SPA_ETHER-3-TCAM_MAC_DA_TABLE_INVALID

3-Error

Subslot [dec]/[dec] [chars] Destination MAC address filter table is invalid for interface [dec]

The internal data structure used by the SPA for managing the destination\n\ MAC address filtering for an interface port is invalid. This error message\n\ indicates the modular services card slot the SPA subslot the SPA type and\n\ the interface port. This error indicates a software caveat.

spa-eth-fe

"Copy the error message text exactly as it appears on the console or in the\n\ system log enter the <CmdBold>show tech-support<NoCmdBold> command\n\ contact your Cisco technical support representative and provide the\n\ representative with the gathered information."

SPA_ETHER-3-TCAM_MAC_DA_TABLE_ACCESS_FAILURE

3-Error

Subslot [dec]/[dec] [chars] Failure in accessing the TCAM destination MAC address table [chars]

Access to the TCAM destination MAC address table for the SPA interface\n\ failed. The error message indicates the modular services card slot the\n\ SPA subslot the SPA type and the affected interface number. This error\n\ indicates either a software caveat or a hardware failure.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show\n\ tech-support<NoCmdBold> command contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

SPA_ETHER-4-TCAM_MAC_DA_TABLE_FULL

4-Warning

Subslot [dec]/[dec] [chars] Destination MAC address filter table is full for interface [dec] MAC address = [enet] mask = [enet]

The TCAM destination MAC address table for an interface on the SPA is\n\ full. The SPA supports a separate MAC table per interface. The error\n\ message indicates the modular services card slot the SPA subslot the SPA\n\ type the affected interface and the MAC address. The specified MAC\n\ address will not be added to the TCAM table.

spa-eth-fe

"Try to remove some of the registered MAC addresses for the interface by\n\ changing the interface configuration. To verify the MAC addresses currently\n\ in use by an interface enter the <CmdBold>show controllers<NoCmdBold>\n\ command."

SPA_ETHER-3-TCAM_VLAN_TABLE_INVALID

3-Error

Subslot [dec]/[dec] [chars] VLAN filter table is invalid for interface [dec]

The internal data structure used by the SPA to manage the VLAN filtering\n\ is invalid. The SPA supports a separate VLAN table per interface. The\n\ error message indicates the modular services card slot the SPA subslot\n\ the SPA type and the affected interface. This error indicates a software\n\ caveat.

spa-eth-fe

"Copy the error message text exactly as it appears on the console or in the\n\ system log enter the <CmdBold>show tech-support<NoCmdBold> command\n\ contact your Cisco technical support representative and provide the\n\ representative with the gathered information."

SPA_ETHER-3-TCAM_VLAN_TABLE_ACCESS_FAILURE

3-Error

Subslot [dec]/[dec] [chars] Failure in accessing the TCAM VLAN address table [chars]

Access to the TCAM VLAN table for the SPA failed. The error message\n\ indicates the modular services card slot the SPA subslot the SPA type and\n\ the affected interface. This error indicates either a software caveat or a\n\ hardware failure.

spa-eth-fe

"Perform OIR of the SPA located in the specified subslot. Before removing\n\ the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command.\n\ Remove the SPA wait 5 seconds and reinsert the SPA into the MSC. If the\n\ problem persists copy the error message text exactly as it appears on the\n\ console or in the system log enter the <CmdBold>show\n\ tech-support<NoCmdBold> command contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information."

SPA_ETHER-4-TCAM_VLAN_TABLE_FULL

4-Warning

Subslot [dec]/[dec] [chars] VLAN filter table is full for interface [dec] VLAN identifier = [dec]

The TCAM VLAN filter table for an interface on the SPA is full. The SPA\n\ supports a separate VLAN table per interface. The error message indicates\n\ the modular services card slot the SPA subslot the SPA type the affected\n\ interface and the VLAN entry that failed. The specified VLAN identifier\n\ will not be added to the TCAM table.

-

"Try to remove some of the registered VLANs for the interface by changing\n\ the interface configuration. To verify the VLAN IDs currently in use by an\n\ interface enter the <CmdBold>show controllers<NoCmdBold> command."

SPA_ETHER-6-TCAM_VLAN_FILTERING_DISABLED

6-Information

Subslot [dec]/[dec] [chars] TCAM VLAN filter table is full disabling VLAN filtering for interface [dec]

VLAN filtering for the specified interface has been disabled because the VLAN table is full. This means that the SPA will transmit frames destined for any VLAN ID to the route processor. The SPA supports a separate VLAN table per interface. The error message indicates the modular services card slot the SPA subslot the SPA type and the affected interface.

spa-eth-fe

"To verify the VLAN IDs that are currently in use by an interface enter " "the <CmdBold>show controllers<NoCmdBold> command. You can remove " "some of the existing VLANs from the interface configuration to " "reactivate VLAN filtering on the indicated interface."

SPA_ETHER-6-TCAM_VLAN_FILTERING_ENABLED

6-Information

Subslot [dec]/[dec] [chars] Enabling VLAN filtering for interface [dec]

VLAN filtering for the specified interface is enabled. The SPA supports a separate VLAN table per interface. The error message indicates the modular services card slot the SPA subslot the SPA type and the affected interface.

spa-eth-fe

"VLAN filtering has been reactivated and the VLAN table is no longer " "full. This means that the SPA will transmit frames to the route " "processor only for those VLAN IDs configured on the specified interface." "To verify the VLAN IDs that are currently in use by an interface " "enter the <CmdBold>show controllers<NoCmdBold> command."

SPA_ETHER-3-SFP_SEC_FAIL

3-Error

[chars] [chars] initialization failure [chars]

The pluggable transceiver module SFP on the Ethernet SPA could not

spa-eth-ge-2

"Try replacing the pluggable transceiver module SFP with a Cisco "

SPA_ETHER-3-SFP_EEPROM_READ_FAIL

3-Error

[chars] [chars] initialization failure [chars]

The pluggable transceiver module SFP on the Ethernet SPA could not be

spa-eth-ge-2

"Try re-inserting the pluggable transceiver module SFP again into the "

ASR1000_SPA_ETHER-3-HSRPDA_TCAM_REGION_FULL

3-Error

Failed to add in HSPRDA region for interface [chars]

The TCAM HSRPDA table on the SPA is full The specified HSRPDA identifier will not be added to the TCAM table.

mcp-io

"Try to remove some of the Virtual MAC addresses for the interface by " "command."

ASR1000_SPA_ETHER-3-TCAM_VLAN_TABLE_FULL

3-Error

Failed to add VLAN [dec] to interface [chars]

The TCAM VLAN filtering table on the SPA is full. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed. The specified VLAN identifier will not be added to the TCAM table.

mcp-io

"Try to remove some of the registered VLANs for the interface by " "changing the interface configuration. To verify the VLAN IDs currently " "in use by an interface enter the <CmdBold>show vlans<NoCmdBold> " "command."

ASR1000_SPA_ETHER-3-TCAM_VLAN_ERROR

3-Error

Failed to [chars] VLAN [dec] to/from interface [chars] status = [dec]

The access to update the TCAM VLAN filtering table on the SPA failed. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed.

mcp-io

LOG_STD_ACTION

ASR1000_SPA_ETHER-3-TCAM_QINQ_VLAN_TABLE_FULL

3-Error

Failed to add VLAN outer [dec] inner [dec]-[dec] to interface [chars]

The TCAM VLAN filtering table on the SPA is full. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed. The specified VLAN identifier will not be added to the TCAM table.

mcp-io

"Try to remove some of the registered VLANs for the interface by " "changing the interface configuration. To verify the VLAN IDs currently " "in use by an interface enter the <CmdBold>show vlans<NoCmdBold> " "command."

ASR1000_SPA_ETHER-3-TCAM_QINQ_VLAN_ERROR

3-Error

Failed to [chars] VLAN outer [dec] inner [dec]-[dec] to/from interface [chars] status = [dec]

The access to update the TCAM VLAN filtering table on the SPA failed. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed.

mcp-io

LOG_STD_ACTION

CLOCK_RECOVERY-4-CLOCK_FAILED

4-Warning

[chars] on module [dec]/[dec] failed

This message indicates that an active recovered or enhanced clock has failed

-

LOG_STD_NO_ACTION

CLOCK_RECOVERY-6-CLOCK_ACTIVE

6-Information

[chars] on module [dec]/[dec] is now active

This message indicates that a recovered or enhanced clock has become active

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_DS1

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec] [chars]

DS1 Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_DS3

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec] [chars]

DS3 Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_DS3_CHANNEL

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec] [chars]

DS3:channelized Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_OCN_VT_T1

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec]/[dec] [chars]

OCN_VT_T1: Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_OCN_CT3

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec] [chars]

OCN_CT3: Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_OCN_T3

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec] [chars]

OCN_T3: Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_STMN_T3

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec] [chars]

STMN_T3: Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_STMN_E3

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec] [chars]

STMN_E3: Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_STMN_VC1x

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec]/[dec] [chars]

STMN_VC1x: Recovered clock status change message

-

LOG_STD_NO_ACTION

CONTROLLER-4-ACR_DCR_CLOCK_STMN_CT3

4-Warning

[chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec]/[dec] [chars]

STMN_CT3: Recovered clock status change message

-

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-3-NGIO_MSG_VER_MISMATCH

3-Error

UCSE [chars] is using incorrect NGIO message version expected version = [dec] current version = [dec]. Please update

UCSE SW is running with a software version that doesn't use the same NGIO message header version. This could happen if the wrong version of the software package for the module was installed in the system.

canisng-xe

"Find the appropriate software package for the module based on the " "Cisco IOS software version that the system is running. Follow the " "installation documentation that corresponds to your software version " "and platform to properly install the software package and correct the " "problem."

SPA_NGIO_UCSE-3-SHUTDOWN_FAILED

3-Error

UCSE Module [chars] shutdown failed to be executed.

The UCSE Module did not yet respond to the shutdown request. This is probably due to a bug.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-SHUTDOWN_NOT_DONE

5-Notice

UCSE Module [chars] shutdown was not done in a proper fashion: Reseating the module may corrupt the hard disk.

The module was not properly shutdown before removal of the module. This could result in the corruption of the hard disk on the module.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-3-SE_RESET

3-Error

UCSE Module [chars] will be reset to recover from failure [chars].

The module is restarting to recover from the communication failure with host.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-3-APP_RESET

3-Error

Application on UCSE Module [chars] has failed and requested a UCSE Module reset.

The application running on the service module failed and as a result the UCSE Module will be restarted in order to recover from the communication failure with host.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-3-APP_STATUS

3-Error

Application on UCSE Module [chars] is [chars]

The Application running on the service module has changed state.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-SHUTDOWN_DONE

5-Notice

UCSE Module [chars] shutdown complete

The shutdown of the UCSE Module was completed.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-SHUTDOWN_BUTTON

5-Notice

UCSE Module [chars] shutdown button was pressed shutdown initiated.

The Shutdown button on the module was pressed and shutdown initiated.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-NEWPASSWORD

5-Notice

UCSE Module [chars] password changed to '[chars]'.

The password of the service module was changed.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-UNCONFIGURE_IP

5-Notice

UCSE Module [chars] \UCSE Module ip address\ unconfigured.

The UCSE Module IP address is unconfigured as interface IP address changed.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-RESTORE_IP

5-Notice

UCSE Module [chars] \UCSE Module ip address\ restored.

The UCSE Module IP address was restored after the system verified that the interface IP address changed. There are certain configuration requirements for the service-engine IP address and the default gateway IP address with the module interface IP address. The system has verified these requirements and restored the IP address.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-UNCONFIGURE_EXT_IP

5-Notice

UCSE Module [chars] \UCSE Module ext ip address\ unconfigured.

The UCSE Module external IP address is unconfigured as interface IP address changed.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-RESTORE_EXT_IP

5-Notice

UCSE Module [chars] \ ucse ext ip address\ restored.

The UCSE Module external IP address was restored after the system verified that the interface IP address changed. There are certain configuration requirements for the UCSE Module IP address and the default gateway IP address with the module interface IP address. The system has verified these requirements and restored the external IP address.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-UNCONFIGURE_DEF_GW

5-Notice

UCSE Module [chars] \UCSE ip default-gateway\ unconfigured.

The UCSE Module default gateway IP is unconfigured as interface IP address changed.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-5-RESTORED_DEF_GW

5-Notice

UCSE Module [chars] \UCSE ip default-gateway\ restored.

The UCSE Module default gateway IP address was restored after the system verified that the interface IP address was changed. There are certain configuration requirements for the UCSE Module IP address and the default gateway IP address with the module interface IP address. The system has verified that the IP address for the UCSE Module IP default gateway is still on the same subnet as the UCSE Module IP address and therefore the default-gateway configuration is restored.

canisng-xe

LOG_STD_NO_ACTION

SPA_NGIO_UCSE-4-BADPLATFORMINFO

4-Warning

UCSE Module [chars] platform information not received correctly.

The platform and service module hardware information was not received correctly.

canisng-xe

LOG_STD_RECUR_ACTION

SPA_NGIO_UCSE-2-CONFIGFAILED

2-Critical

UCSE Module [chars] \[chars]\ configuration failed

The indicated configuration for the UCSE Module interface has failed.

canisng-xe

LOG_STD_RECUR_ACTION

SPA_NGIO_UCSE-3-SW_ERR

3-Error

NULL

The module driver detected a software error condition on the module card. This might result in improper operation.

canisng-xe

"The module driver has encountered a software error." "Please power down and reseat the indicated module card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log module all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SPA_NGIO_UCSE-3-PASSWORDRESET

3-Error

UCSE Module [chars] password reset [chars][chars]

The password reset of the service module failed or is not supported.

canisng-xe

LOG_STD_RECUR_ACTION

SPA_NGIO_UCSE-3-SPA_CPU_ERR

3-Error

[chars]: module CPU HW errors: [chars]

An internal hardware device error has occurred on the module CPU. The error message indicates the modular card slot the module subslot the module type and the name of the hardware device. The module has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the module will be made. This message is likely due to an unrecoverable hardware failure

canisng-xe

"If the module does not recover automatically perform OIR of the module " "located in the specified subslot. Before removing the module enter the " "<CmdBold>hw-module subslot stop<NoCmdBold> command. Remove the module " "wait 5 seconds and reinsert the module into the slot. If the problem " "persists copy the error message text exactly as it appears on the " "console or in the system log enter the <CmdBold>show tech-support" "<NoCmdBold> command contact your Cisco technical support representative " "and provide the representative with the gathered information."

SPA_NGIO_UCSE-3-HW_ERR

3-Error

[chars]: A Hardware device error was detected by [chars] trying to recover the module by reload.

An internal hardware device error has occurred on the module. The error message indicates the slot the module subslot the module type and the name of the hardware device. The module has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the module will be made. This message is likely due to an unrecoverable hardware failure.

canisng-xe

"Perform OIR of the module located in the specified subslot. Before" " removing the module enter the <CmdBold>hw-module subslot" " stop<NoCmdBold> command. Remove the module wait 5 seconds and" " reinsert the module into the slot. If the problem persists copy " "the error message text exactly as it appears on the console or in " "the system log enter the <CmdBold>show diag <NoCmdBold> command " "contact your Cisco technical support representative and provide the " "representative with the gathered information."

SPA_NGIO_UCSE-0-APP_MSG_EMER

0-Emergency

NULL

The application running on the service module has encountered an emergency error.

canisng-xe

UCSE_APP_MSG_STD_ACTION

SPA_NGIO_UCSE-1-APP_MSG_ALERT

1-Alert

NULL

The application running on the service module has issued an alert.

canisng-xe

UCSE_APP_MSG_STD_ACTION

SPA_NGIO_UCSE-2-APP_MSG_CRIT

2-Critical

NULL

The application running on the service module has encountered a critical error.

canisng-xe

UCSE_APP_MSG_STD_ACTION

SPA_NGIO_UCSE-3-APP_MSG_ERR

3-Error

NULL

The application running on the service module has encountered an error.

canisng-xe

UCSE_APP_MSG_STD_ACTION

SPA_NGIO_UCSE-4-APP_MSG_WARN

4-Warning

NULL

The application running on the service module has issued a warning message.

canisng-xe

UCSE_APP_MSG_STD_ACTION

SPA_NGIO_UCSE-5-APP_MSG_NOTICE

5-Notice

NULL

The application running on the service module has issued a notice.

canisng-xe

"Refer to the software application documentation for more information."

SPA_NGIO_UCSE-6-APP_MSG_INFO

6-Information

NULL

The application running on the service module has issued a informational message.

canisng-xe

"Refer to the software application documentation for more information."

SPA_NGIO_UCSE-7-APP_MSG_DEBUG

7-Debug

NULL

The application running on the service module has displayed a debug message.

canisng-xe

"Refer to the software application documentation for more information."

SPA_UCSE_IF-3-UCSE_IF_SW_ERR

3-Error

NULL

The module driver detected a software error condition on the module card. This might result in improper operation.

canisng-xe

"The module driver has encountered a software error. Power down and " "reseat the indicated module card. If the problem persists copy the " "error message exactly as it appears in the console and open a case " "with the Technical Assistance Center via the Internet at " TAC_CASE_OPEN " or contact your " "Cisco technical support representative and provide the representative " "with the information you have gathered. Be sure to attach to your case " "the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-trace spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

EIO-3- NOPROC

3-Error

Unable to create process.

failed to create eio process.

-

LOG_STD_ACTION

EIO-3- NOMEM

3-Error

out of memory.

failed to malloc memory.

-

LOG_STD_ACTION

EIO-3- NOQUEUE

3-Error

Unable to create queue.

failed to create queue.

-

LOG_STD_ACTION

EIO-3- NOCHUNK

3-Error

Unable to create memory chunk.

failed to create memory chunk.

-

LOG_STD_ACTION

EIO-3- NOCDB

3-Error

Unable to create controller cdb.

failed to create controller cdb.

-

LOG_STD_ACTION

EIO-4- INVALID_CDB

4-Warning

Invalid eio controller cdb.

encountered an invalid controller cdb.

-

LOG_STD_ACTION

EIO-4- INVALID_SLOT

4-Warning

Invalid eio slot instance.

encountered an invalid eio slot instance.

-

LOG_STD_ACTION

EIO-4- EMPTY_CHUNK

4-Warning

Chunk is empty.

failed to malloc chunk entry due to empty chunk.

-

LOG_STD_ACTION

SPA_TDMIM-3-NULL_DATA_STRUCTURE

3-Error

[chars]

A software error occured and SPA driver is not able to retrieve the data structure mentioned in the message.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-UNSUPPORTED_DATA

3-Error

common_str_empty_str

A software error occured and SPA driver encounterd unsupported data mentioned in the message

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-TDL_SEND_FAIL

3-Error

common_str_empty_str

Failed to send TDL message.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-MSG_ENQUEUE_ERROR

3-Error

[chars]

Failed to enqueue a message.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-ID_INIT

3-Error

failed to initialize TDM IM ID table

Failed to initialize TDM IM ID table.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-ID_ALLOC_ERR

3-Error

failed to allocate ID for TDM IM

Failed to allocate ID for TDM IM.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-DPIDX_LKUP_ERR

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

uea-im-tdm

LOG_STD_NO_ACTION

SPA_TDMIM-3-VLAN_ID_NONZERO

3-Error

VLAN identifier is not zero before allocation for interface [chars]

The SPA driver is seeing non zero VLAN identifier before allocating new vlan identifier for the interface specified in the message. This indicates a software error.

uea-im-tdm

LOG_STD_NO_ACTION

SPA_TDMIM-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

The Periodic one second process creation failed. This indicates a software error.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-ATM_IF_CREATE

3-Error

ATM interface creation on [chars] controller failed

ATM interface creation on a controller failed. This indicates a software error.

uea-im-tdm

LOG_STD_ACTION

SPA_TDMIM-3-ATM_LICENSE_NOT_ACTIVATED

3-Error

\nATM License is not yet activated. \ \nPlease configure 'license feature atm' \ \nand accept the EULA to activate the license.\n

Failed to start ATM services as feature license is not installed or activated

uea-im-tdm

LOG_STD_ACTION

SPA_SRVCS_ENGINE-3-RBCP_MSG_VER_MISMATCH

3-Error

Service Engine [chars] is using incorrect RBCP message version expected version = [dec] current version = [dec]. Please update

The service engine is running with a software version that doesn't use the same RBCP message header version. This could happen if the wrong version of the software package for the SPA was installed in the system.

spa-butler-all

"Find the appropriate software package for the SPA based on the " "Cisco IOS software version that the system is running. Follow the " "installation documentation that corresponds to your software version " "and platform to properly install the software package and correct the " "problem."

SPA_SRVCS_ENGINE-3-SHUTDOWN_FAILED

3-Error

Service Engine [chars] shutdown failed to be executed.

The service engine did not yet respond to the shutdown request. This is probably due to a bug.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-SHUTDOWN_NOT_DONE

5-Notice

Service Engine [chars] shutdown was not done in a proper fashion: Reseating the SPA may corrupt the hard disk.

The SPA was not properly shutdown before removal of the SPA. This could result in the corruption of the hard disk on the SPA.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-3-SE_RESET

3-Error

Service engine [chars] will be reset to recover from failure [chars].

The service SPA is restarting to recover from the communication failure with host.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-3-APP_RESET

3-Error

Application on service engine [chars] has failed and requested a service engine reset.

The application running on the service SPA failed and as a result the service engine will be restarted in order to recover from the communication failure with host.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-3-APP_STATUS

3-Error

Application on service engine [chars] is [chars]

The Application running on the service SPA has changed state.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-SHUTDOWN_DONE

5-Notice

Service engine [chars] shutdown complete

The shutdown of the service engine was completed.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-SHUTDOWN_BUTTON

5-Notice

Service engine [chars] shutdown button was pressed shutdown initiated.

The Shutdown button on the SPA was pressed and shutdown initiated.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-NEWPASSWORD

5-Notice

Service Engine [chars] password changed to '[chars]'.

The password of the service SPA was changed.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-UNCONFIGURE_IP

5-Notice

Service Engine [chars] \service-engine ip address\ unconfigured.

The service-engine IP address is unconfigured as interface IP address changed.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-RESTORE_IP

5-Notice

Service Engine [chars] \service-engine ip address\ restored.

The service-engine IP address was restored after the system verified that the interface IP address changed. There are certain configuration requirements for the service-engine IP address and the default gateway IP address with the SPA interface IP address. The system has verified these requirements and restored the IP address.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-UNCONFIGURE_EXT_IP

5-Notice

Service Engine [chars] \service-engine ext ip address\ unconfigured.

The service-engine external IP address is unconfigured as interface IP address changed.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-RESTORE_EXT_IP

5-Notice

Service Engine [chars] \service-engine ext ip address\ restored.

The service-engine external IP address was restored after the system verified that the interface IP address changed. There are certain configuration requirements for the service-engine IP address and the default gateway IP address with the SPA interface IP address. The system has verified these requirements and restored the external IP address.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-UNCONFIGURE_DEF_GW

5-Notice

Service Engine [chars] \service-engine ip default-gateway\ unconfigured.

The service-engine default gateway IP is unconfigured as interface IP address changed.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-5-RESTORED_DEF_GW

5-Notice

Service Engine [chars] \service-engine ip default-gateway\ restored.

The service-engine default gateway IP address was restored after the system verified that the interface IP address was changed. There are certain configuration requirements for the service-engine IP address and the default gateway IP address with the SPA interface IP address. The system has verified that the IP address for the service-engine IP default gateway is still on the same subnet as the service-engine IP address and therefore the default-gateway configuration is restored.

spa-butler-all

LOG_STD_NO_ACTION

SPA_SRVCS_ENGINE-4-BADPLATFORMINFO

4-Warning

Service Engine [chars] platform information not received correctly.

The platform and service SPA hardware information was not received correctly.

spa-butler-all

LOG_STD_RECUR_ACTION

SPA_SRVCS_ENGINE-2-CONFIGFAILED

2-Critical

Service Engine [chars] \[chars]\ configuration failed

The indicated configuration for the service-engine interface has failed.

spa-butler-all

LOG_STD_RECUR_ACTION

SPA_SRVCS_ENGINE-3-SW_ERR

3-Error

NULL

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-butler-all

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SPA_SRVCS_ENGINE-3-PASSWORDRESET

3-Error

Service Engine [chars] password reset [chars][chars]

The password reset of the service SPA failed or is not supported.

spa-butler-all

LOG_STD_RECUR_ACTION

SPA_SRVCS_ENGINE-3-SPA_CPU_ERR

3-Error

[chars]: SPA CPU HW errors: [chars]

An internal hardware device error has occurred on the Services SPA CPU. The error message indicates the modular services card slot the SPA subslot the SPA type and the name of the hardware device. The SPA has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the SPA will be made. This message is likely due to an unrecoverable hardware failure

spa-butler-all

"If the SPA does not recover automatically perform OIR of the SPA " "located in the specified subslot. Before removing the SPA enter the " "<CmdBold>hw-module subslot stop<NoCmdBold> command. Remove the SPA " "wait 5 seconds and reinsert the SPA into the SIP. If the problem " "persists copy the error message text exactly as it appears on the " "console or in the system log enter the <CmdBold>show tech-support" "<NoCmdBold> command contact your Cisco technical support representative " "and provide the representative with the gathered information."

SPA_SRVCS_ENGINE-3-HW_ERR

3-Error

[chars]: A Hardware device error was detected by [chars] trying to recover the SPA by reload.

An internal hardware device error has occurred on the services SPA. The error message indicates the SIP slot the SPA subslot the SPA type and the name of the hardware device. The SPA has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the SPA will be made. This message is likely due to an unrecoverable hardware failure.

spa-butler-all

"Perform OIR of the SPA located in the specified subslot. Before removing " "the SPA enter the <CmdBold>hw-module subslot stop<NoCmdBold> command. " "Remove the SPA wait 5 seconds and reinsert the SPA into the SIP. If " "the problem persists copy the error message text exactly as it appears " "on the console or in the system log enter the <CmdBold>show diag" "<NoCmdBold> command contact your Cisco technical support representative " "and provide the representative with the gathered information."

SPA_SRVCS_ENGINE-0-APP_MSG_EMER

0-Emergency

NULL

The application running on the service SPA has encountered an emergency error.

spa-butler-all

SE_APP_MSG_STD_ACTION

SPA_SRVCS_ENGINE-1-APP_MSG_ALERT

1-Alert

NULL

The application running on the service SPA has issued an alert.

spa-butler-all

SE_APP_MSG_STD_ACTION

SPA_SRVCS_ENGINE-2-APP_MSG_CRIT

2-Critical

NULL

The application running on the service SPA has encountered a critical error.

spa-butler-all

SE_APP_MSG_STD_ACTION

SPA_SRVCS_ENGINE-3-APP_MSG_ERR

3-Error

NULL

The application running on the service SPA has encountered an error.

spa-butler-all

SE_APP_MSG_STD_ACTION

SPA_SRVCS_ENGINE-4-APP_MSG_WARN

4-Warning

NULL

The application running on the service SPA has issued a warning message.

spa-butler-all

SE_APP_MSG_STD_ACTION

SPA_SRVCS_ENGINE-5-APP_MSG_NOTICE

5-Notice

NULL

The application running on the service SPA has issued a notice.

spa-butler-all

"Refer to the software application documentation for more information."

SPA_SRVCS_ENGINE-6-APP_MSG_INFO

6-Information

NULL

The application running on the service SPA has issued a informational message.

spa-butler-all

"Refer to the software application documentation for more information."

SPA_SRVCS_ENGINE-7-APP_MSG_DEBUG

7-Debug

NULL

The application running on the service SPA has displayed a debug message.

spa-butler-all

"Refer to the software application documentation for more information."

SPA_SRVCS_IF-3-SRVCS_IF_SW_ERR

3-Error

NULL

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-butler-all

"The SPA driver has encountered a software error. Power down and reseat " "the indicated SPA card. If the problem persists copy the error message " "exactly as it appears in the console and open a case with the Technical " "Assistance Center via the Internet at " TAC_CASE_OPEN " or contact your " "Cisco technical support representative and provide the representative " "with the information you have gathered. Be sure to attach to your case " "the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SPA_IPSEC-3-PWRCYCLE

3-Error

SPA [dec]/[dec] is being power-cycled

The SPA has stopped responding to keep-alive polling from carrier card. The SPA has been power-cycled.

spa-ipsec-2g

"Once the SPA is back online retrieve the crashdump data that " "was saved on the Bootflash of the supervisor." LOG_STD_RECUR_ACTION

SPA_IPSEC-3-BRDTYPE

3-Error

Incorrect jacket card board type [dec] detected.

Board type does not belong to either C7600-SSC-400 or C7600-SSC-600

spa-ipsec-2g

"LOG_STD_RECUR_ACTION"

SPA_IPSEC-3-PROC_FAIL

3-Error

[chars]: [chars] Process creation failed.

Can not allocate memory for specified process.

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPA_IPSEC-3-BOOT_FAIL

3-Error

[chars]: [chars].

The SPA failed to boot up for the specified reason

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPA_IPSEC-3-OVERRIDE

3-Error

[chars]: Overriding bundled firmware with ssc[dec]-[chars].

Used specified file instead of bundled file. This is a debugging feature.

spa-ipsec-2g

LOG_STD_NO_ACTION

SPA_IPSEC-3-SKIP_SPI

3-Error

[chars]: Skipping SPI Init.

SPI Initialization will be skipped. This is a debugging feature.

ws-ipsec-3

LOG_STD_NO_ACTION

SPA_IPSEC-3-SPA_BUS

3-Error

[chars]: SPA Bus timeout.

There was a timeout trying to access the SPA. Please reseat the board and try again.

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPA_ATM_ENABLER-3-SPA_ATM_LICENSE_EULA_NOT_ACCEPTED

3-Error

\n********************************************************* \ \nWARNING: SPA ATM License is not yet activated. \ \nPlease configure 'license feature atm'\ \nand accept the EULA to activate the license. \ \n*********************************************************\n

EULA is not accepted for the license

ios-licensing-atg

LOG_STD_ACTION

ATMSPA-3-FATAL_ERROR

3-Error

occurred on [chars]. Resetting SPA

The SPA has been reset due to a critical error in one of its devices. The error could either be a single occurrence of an event or multiple occurrences within a period of time. The message text on the console or in the system log provides more information on the specific nature of the error.

spa-atm-all

"If the SPA is reset more than once copy the error " "message exactly as it appears. Next research and attempt to resolve the " "issue using the SPA hardware troubleshooting documentation as well " "as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ATMSPA-4-SETUPVC

4-Warning

Interface [chars] VC [dec] setup failed reason = [dec]

A command to setup a VC has failed on RP.

spa-atm-all

"The SPA ATM driver has detected a problem creating the internal OAM" "VC. Reload the indicated SPA card to reconfigure the internal OAM VC." "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ATMSPA-4-TEARDOWNVC

4-Warning

Interface [chars] VC [dec] teardown failed reason = [dec]

A command to remove a VC config has failed on RP.

spa-atm-all

"The SPA ATM driver has detected a problem tearing down the internal" "OAM VC. Reload the indicated SPA card to do a clean tear down of the " "internal OAM VC. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve " "the issue using the SPA hardware troubleshooting documentation as well" " as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ATMSPA-3-SW_ERROR

3-Error

[chars] Error 0x[hec] [chars]

The specified software error has been detected.

-

LOG_STD_SH_TECH_ACTION

ATMSPA-3-HW_ERROR

3-Error

[chars] Error 0x[hec] [chars]

The specified hardware error has been detected.

-

"The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION

ATMSPA-3-KEEPALIVE_FAILURE

3-Error

occurred on [chars]. Resetting SPA

One of the devices of the SPA failed to respond to keepalives due to which SPA has been reset. The message text on the console or in the system log provides more information on which device failed to respond.

spa-atm-all

"If the SPA is reset more than once copy the error " "message exactly as it appears. Next research and attempt to resolve the " "issue using the SPA hardware troubleshooting documentation as well " "as the tools and utilities provided at " BUG_TOOLKIT "If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Be sure to provide the information you have " "gathered and <cmdBold>show tech-support<nocmdBold> to your support " "representative or attach it to your case"

ATMSPA-3-DATA_ERROR

3-Error

[chars] Error 0x[hec] [chars]

A datapath protocol violation or sequence error has been detected.

-

"The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION

ATMSPA-3-GEN_ERROR

3-Error

[chars] Error 0x[hec] [chars]

The specified error has been detected.

-

LOG_STD_SH_TECH_ACTION

ATMSPA-2-INITFAIL

2-Critical

[chars] - Init Failed return code: [dec]

The SPA failed to complete hardware initialization. One of the devices in the SPA failed to initialize successfully. Information about the failed device is specified in the message text on the console or in the system log.

-

"Please power down and reseat the indicated SPA card. If the condition " "persists copy the error message exactly as it appears. Next research " "and attempt to resolve the issue using the SPA hardware troubleshooting " "documentation as well as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ATMSPA-4-VCSETUP

4-Warning

[chars]: VC setup command received on the LC for an existing VC VCD [dec]

A command to set up a VC has been received for a VC that has already been set up. The VC has already been configured by a previous setup VC command from the RP. A duplicate setup command may indicate that the RP did not receive a response from the LC for the previous setup command.

-

LOG_STD_NO_ACTION

ATMSPA-4-VCTEARDOWN

4-Warning

[chars]: VC tear down command received on the LC for a non-existing VC VCD [dec]

The VC does not exist on the LC. Most likely it has been torn down by a previous teardown command from RP. A duplicate teardown command may indicate that the RP did not receive a response from the LC for the previous teardown command.

-

LOG_STD_NO_ACTION

ATMSPA-4-VPSETUP

4-Warning

[chars]: VP setup command received on the LC for an existing VP VPI [dec]

A command to set up a VP has been received for a VP that has already been set up. The VP has already been configured by a previous setup VP command from the RP. A duplicate setup command may indicate that the RP did not receive a response from the LC for the previous setup command.

-

LOG_STD_NO_ACTION

ATMSPA-4-VPTEARDOWN

4-Warning

[chars]: VP tear down command received on the LC for a non-existing VP VPI [dec]

The VP does not exist on the LC. Most likely it has been torn down by a previous teardown command from RP. A duplicate teardown command may indicate that the RP did not receive a response from the LC for the previous teardown command.

-

LOG_STD_NO_ACTION

ATMSPA-3-VCQ_ERROR

3-Error

[chars]: VC queue configuration failed due to un-initialized queue table global identifier [dec]

Software configuration of a VC queue failed due to un-initialized queue table.

-

"Attempt to perform a soft OIR operation by entering the command " "that is described in the shared port adapter software configuration " "guide. If the condition persists copy the error message exactly as it " "appears and report it to your technical support representative. " "Also supply a 'show tech-support' at that time."

ATMSPA-3-QOS_ALLOC_FAILED

3-Error

[chars] [chars] [chars]: [dec]

Traffic shaping parameters could not be configured because the number of unique shaping parameters that are configured on the PVCs or PVPs in this specified ATM SPA is over the maximum limit. The maximum number of unique shaping parameters that can be configured on the PVCs or PVPs is 4096.

spa-atm-all

"Ensure that the total number of unique shaping parameters " "that are configured on both PVCs and PVPs does not exceed " "the maximum limit of 4096."

ATMSPA-3-FPD_VER_DEPENDENCY_NOTE

3-Error

Cannot perform the requested FPD update operation because [chars] in subslot [dec]/[dec] has incompatible HW version [dec].[dec] with FPD image version [dec].[dec] for FPD ID [dec]. Only image version greater than [dec].[dec] can be used in the update operation of [chars] with HW version greater than [dec].[dec].

The version of the FPD image from the FPD image bundle or package is not compatible with the HW version of the target card

spa-atm-all

LOG_STD_ACTION

ATMSPA-3-ATM_SPA_AUTOVC_FAIL

3-Error

[chars]: atm autovc discovery configuration failed reason: [chars]

A command to configure the atm autovc discovery on an atm interface has failed

spa-atm-all

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-4-SETUPVC

4-Warning

Interface [chars] VC [dec] setup failed reason = [dec]

A command to setup a VC has failed on RP.

asr1k-spa-atm

"The SPA ATM driver has detected a problem creating the internal OAM" "VC. Reload the indicated SPA card to reconfigure the internal OAM VC." "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ASR1000_RP_ATM_SPA-4-TEARDOWNVC

4-Warning

Interface [chars] VC [dec] teardown failed vc state = [dec]/[dec]

A command to remove a VC config has failed on RP.

asr1k-spa-atm

"The SPA ATM driver has detected a problem tearing down the internal" "OAM VC. Reload the indicated SPA card to do a clean tear down of the " "internal OAM VC. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve " "the issue using the SPA hardware troubleshooting documentation as well" " as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ASR1000_RP_ATM_SPA-5-MPVCVPSETUP

5-Notice

Interface [chars] has a VC/VP [dec] configured already VC/VP [dec] cannot

The SPA ATM driver supports configuring only one VC/VP under a point to multi point sub-interface. The sub-interface specified in the message already has VP/VC configured.

-

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_FLOWID_GET_FAIL

3-Error

Failed to get a flow control identifier for interface [chars] for index [dec]

The SPA driver is not able to obtain the datapath flow control identifier for the data path identifier under the interface specified in the message. This indicates a software error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_DPIDB_ALLOC_FAIL

3-Error

Failed to allocate a data plane identifier for interface [chars] for VCD [dec]

The SPA driver is not able to allocate the datapath identifier for the VCD under the interface specified in the message. This indicates a software error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_INGRESS_ID_ALLOC_FAIL

3-Error

Failed to allocate VC ingress identifier on interface [chars] for VCD [dec] ebfc_id [dec] when [chars]

The ATM SHIM is not able to allocate the ingress identifier for the VCD under the interface specified in the message. This indicates a software error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_DPIDB_GET_FAIL

3-Error

Failed to get a data plane identifier for interface [chars] for VCD [dec]

The SPA driver is not able to obtain the datapath identifier for the VCD under the interface specified in the message. This indicates a software error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_TXCHANL_GET_FAIL

3-Error

Failed to get a valid tx_chan id for interface [chars] for VCD [dec]

The SPA driver is not able to obtain the datapath tx channel identifier for the VCD under the interface specified in the message. This indicates a SPA occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_SPA_SETUP_FAIL

3-Error

SPA Error response on interface [chars] when [chars] for VCD [dec] ebfc_id [dec] ret_val [dec]

The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_CFG_SEND_FAIL

3-Error

Error in sending message to SPA on interface [chars] when [chars] for VCD [dec] ebfc_id [dec]

The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_CORE_GET_FAIL

3-Error

Failed to get a ATM VC core info for interface [chars] VCD [dec]

Could not get VC core information when get SPA VCOPEN or VCMODIRY response. This indicates a ATM information error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_ENCAP_GET_FAIL

3-Error

Failed to get ATM encapsulation for interface [chars] [dec]/[dec] VCD [dec]

Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_ERROR_ENCAP_TYPE

3-Error

Get ATM ERROR encapsulation for interface [chars] [dec]/[dec] VCD [dec]

Get a ERROR VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_CON_SET_FAIL

3-Error

Failed set ATM con for interface [chars] [dec]/[dec] VCD [dec]

Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_EGRESSID_UPDATE_FAIL

3-Error

Failed to update ATM egress id for interface [chars] VCD [dec] egress_id [dec]

Could not update VC egress id when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-ATM_VC_DPIDX_GET_FAIL

3-Error

Failed to get ATM dpidx for interface [chars] VCD [dec]

Could not get VC dpidx information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

ask1k-atm

LOG_STD_NO_ACTION

ASR1000_RP_ATM_SPA-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

The Periodic one second process creation failed. This indicates a software error.

asr1k-atm

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-3-ATM_SPA_AUTOVC_FAIL

3-Error

[chars]: atm autovc discovery configuration failed reason: [chars]

A command to configure the atm autovc discovery on an atm interface has failed

-

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-3-ATM_SPA_VC_MAX_LIMIT_REACHED

3-Error

total active atm vc reached system limitation of [dec]

total number of active atm vc has reached max limit allowed on the system

-

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-4-ATM_SPA_VC_ABOVE_WM_WARNING

4-Warning

total active atm vc approaching [dec] percent of system limitation of [dec]

total number of active atm vc is approaching the high water mark of sysyem limitation

-

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-5-ATM_SPA_VC_BELOW_WM_NOTICE

5-Notice

total active atm vc below [dec] percent of system limitation of [dec]

total number of active atm vc below the high water mark of sysyem limitation

asr1k-atm

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED

3-Error

total active atm vc per ATM SPA reached limitation of [dec]

total number of active atm vc per ATM SPA has reached max limit

-

LOG_STD_ACTION

ASR900_RP_ATM_SPA-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED

3-Error

total active atm vc per ATM SPA reached limitation of [dec]

total number of active atm vc per ATM SPA has reached max limit

-

LOG_STD_ACTION

NCS4200_RP_ATM_SPA-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED

3-Error

total active atm vc per ATM SPA reached limitation of [dec]

total number of active atm vc per ATM SPA has reached max limit

-

LOG_STD_ACTION

ASR1000_RP_ATM_SPA-3-ATM_FLOWID_OUT_OF_RANGE

3-Error

Flow control identifiers for interface [chars] chan lo [hec] chan hi [hec]

The flow control identifier received for the interface is out of range. This indicates SPA driver is responding with out of range flow control identifier

asr1k-atm

LOG_STD_ACTION

VDSL_SFP_MGR-4-DUMP_DELT_START

4-Warning

Dump DELT info started on interface [chars]

Dump DELT information of SFP is started

-

"LOG_STD_ACTION"

VDSL_SFP_MGR-4-DUMP_DELT_DONE

4-Warning

Dump DELT info done on interface [chars]

Dump DELT information of SFP is done.

-

"LOG_STD_ACTION"

VDSL_SFP_MGR-4-DUMP_START

4-Warning

Dump internal info started on interface [chars]

Dump internal information of SFP is started

-

"LOG_STD_ACTION"

VDSL_SFP_MGR-4-DUMP_DONE

4-Warning

Dump internal info done please shut/no shut on interface [chars] to recover

Dump internal information of SFP is done need to reset SFP

-

"LOG_STD_ACTION"

VDSL_SFP_MGR-4-DYING_GASP_ARMED

4-Warning

Dying Gasp Armed on interface [chars] SFP

Dying gasp ready to function if power off now

-

"LOG_STD_ACTION"

VDSL_SFP_MGR-4-DYING_GASP_DISARMED

4-Warning

Dying Gasp Disarmed on interface [chars] SFP

Dying gasp disabled

-

"LOG_STD_ACTION"

ISR4000_RP_NGIO_ATM-4-SETUPVC

4-Warning

Interface [chars] VC [dec] setup failed reason = [dec]

A command to setup a VC has failed on RP.

esg-io-infra

"The SPA ATM driver has detected a problem creating the internal OAM" "VC. Reload the indicated SPA card to reconfigure the internal OAM VC." "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ISR4000_RP_NGIO_ATM-4-TEARDOWNVC

4-Warning

Interface [chars] VC [dec] teardown failed vc state = [dec]/[dec]

A command to remove a VC config has failed on RP.

esg-io-infra

"The SPA ATM driver has detected a problem tearing down the internal" "OAM VC. Reload the indicated SPA card to do a clean tear down of the " "internal OAM VC. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve " "the issue using the SPA hardware troubleshooting documentation as well" " as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

ISR4000_RP_NGIO_ATM-5-MPVCVPSETUP

5-Notice

Interface [chars] has a VC/VP [dec] configured already VC/VP [dec] cannot

The SPA ATM driver supports configuring only one VC/VP under a point to multi point sub-interface. The sub-interface specified in the message already has VP/VC configured.

-

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_FLOWID_GET_FAIL

3-Error

Failed to get a flow control identifier for interface [chars] for index [dec]

The SPA driver is not able to obtain the datapath flow control identifier for the data path identifier under the interface specified in the message. This indicates a software error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_DPIDB_ALLOC_FAIL

3-Error

Failed to allocate a data plane identifier for interface [chars] for VCD [dec]

The SPA driver is not able to allocate the datapath identifier for the VCD under the interface specified in the message. This indicates a software error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_INGRESS_ID_ALLOC_FAIL

3-Error

Failed to allocate VC ingress identifier on interface [chars] for VCD [dec] ebfc_id [dec] when [chars]

The ATM SHIM is not able to allocate the ingress identifier for the VCD under the interface specified in the message. This indicates a software error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_DPIDB_GET_FAIL

3-Error

Failed to get a data plane identifier for interface [chars] for VCD [dec]

The SPA driver is not able to obtain the datapath identifier for the VCD under the interface specified in the message. This indicates a software error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_TXCHANL_GET_FAIL

3-Error

Failed to get a valid tx_chan id for interface [chars] for VCD [dec]

The SPA driver is not able to obtain the datapath tx channel identifier for the VCD under the interface specified in the message. This indicates a SPA occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_SPA_SETUP_FAIL

3-Error

SPA Error response on interface [chars] when [chars] for VCD [dec] ebfc_id [dec] ret_val [dec]

The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_CFG_SEND_FAIL

3-Error

Error in sending message to SPA on interface [chars] when [chars] for VCD [dec] ebfc_id [dec]

The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_CORE_GET_FAIL

3-Error

Failed to get a ATM VC core info for interface [chars] VCD [dec]

Could not get VC core information when get SPA VCOPEN or VCMODIRY response. This indicates a ATM information error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_ENCAP_GET_FAIL

3-Error

Failed to get ATM encapsulation for interface [chars] [dec]/[dec] VCD [dec]

Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_ERROR_ENCAP_TYPE

3-Error

Get ATM ERROR encapsulation for interface [chars] [dec]/[dec] VCD [dec]

Get a ERROR VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_CON_SET_FAIL

3-Error

Failed set ATM con for interface [chars] [dec]/[dec] VCD [dec]

Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_EGRESSID_UPDATE_FAIL

3-Error

Failed to update ATM egress id for interface [chars] VCD [dec] egress_id [dec]

Could not update VC egress id when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_VC_DPIDX_GET_FAIL

3-Error

Failed to get ATM dpidx for interface [chars] VCD [dec]

Could not get VC dpidx information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error.

esg-io-infra

LOG_STD_NO_ACTION

ISR4000_RP_NGIO_ATM-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

The Periodic one second process creation failed. This indicates a software error.

esg-io-infra

LOG_STD_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_SPA_AUTOVC_FAIL

3-Error

[chars]: atm autovc discovery configuration failed reason: [chars]

A command to configure the atm autovc discovery on an atm interface has failed

-

LOG_STD_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_SPA_VC_MAX_LIMIT_REACHED

3-Error

total active atm vc reached system limitation of [dec]

total number of active atm vc has reached max limit allowed on the system

-

LOG_STD_ACTION

ISR4000_RP_NGIO_ATM-4-ATM_SPA_VC_ABOVE_WM_WARNING

4-Warning

total active atm vc approaching [dec] percent of system limitation of [dec]

total number of active atm vc is approaching the high water mark of sysyem limitation

-

LOG_STD_ACTION

ISR4000_RP_NGIO_ATM-5-ATM_SPA_VC_BELOW_WM_NOTICE

5-Notice

total active atm vc below [dec] percent of system limitation of [dec]

total number of active atm vc below the high water mark of sysyem limitation

esg-io-infra

LOG_STD_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED

3-Error

total active atm vc per ATM SPA reached limitation of [dec]

total number of active atm vc per ATM SPA has reached max limit

-

LOG_STD_ACTION

ISR4000_RP_NGIO_ATM-3-ATM_FLOWID_OUT_OF_RANGE

3-Error

Flow control identifiers for interface [chars] chan lo [hec] chan hi [hec]

The flow control identifier received for the interface is out of range. This indicates SPA driver is responding with out of range flow control identifier

esg-io-infra

LOG_STD_ACTION

SPA_NGIO_ETHER_INTERNAL-3-SW_ERR

3-Error

NULL

The module driver detected a software error condition on the module card. This might result in improper operation.

lebowski-o2

"The module driver has encountered a software error." "Please power down and reseat the indicated module card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log module all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SPA_ETHER_INTERNAL_IF-3-ETHER_INTERNAL_IF_SW_ERR

3-Error

NULL

The module driver detected a software error condition on the module card. This might result in improper operation.

lebowski-o2

"The module driver has encountered a software error. Power down and " "reseat the indicated module card. If the problem persists copy the " "error message exactly as it appears in the console and open a case " "with the Technical Assistance Center via the Internet at " TAC_CASE_OPEN " or contact your " "Cisco technical support representative and provide the representative " "with the information you have gathered. Be sure to attach to your case " "the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-trace spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

CELLWAN-2-NO_PROCESS

2-Critical

Could not start process [chars]

Could not start one of the processes.

esg-lte

"Add more memory."

CELLWAN-2-SEND_TIMEOUT

2-Critical

[chars] not responding

The cellular modem is not responding.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-HEART_BEAT_TIMEOUT

2-Critical

No heart beat signal from [chars]

The cellular modem is not responding.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-MODEM_TOO_HOT

2-Critical

[chars] modem will be [chars]

Modem radio temperature has reached critical point. The call will be disconnected and the modem could be shutdown.

esg-lte

"Check if the router fans are working properly."

CELLWAN-2-MODEM_NOT_ACTIVATED

2-Critical

[chars] modem has not been activated

The cellular modem has not been activated by the cellular provider.

esg-lte

"Please check the user documentation on how to activate the modem. " "The cellular modem needs to be activated before it can be used on " "a cellular network."

CELLWAN-2-MODEM_RADIO

2-Critical

[chars] Modem radio has been turned [chars]

Modem radio has been turned on/off.

esg-lte

"show cellular x/x/x radio command " "and <CmdBold>show tech-support"

CELLWAN-2-MODEM_UP

2-Critical

Modem in slot [dec]/[dec] is now UP

The cellular modem is now UP.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-NC_EVENT1

2-Critical

[chars]: Network change event - fallback from ENDC to LTE.

Modem fallback from ENDC to LTE

esg-lte

"No action"

CELLWAN-2-NC_EVENT2

2-Critical

[chars]: Network change event - activated 4G Carrier Aggregation.

Modem activated 4G Carrier Aggregation

esg-lte

"No action"

CELLWAN-2-NC_EVENT3

2-Critical

[chars]: Network change event - activated 5G ENDC.

Modem activated 5G ENDC

esg-lte

"No action"

CELLWAN-2-MODEM_DOWN

2-Critical

Modem in slot [dec]/[dec] is DOWN

The cellular modem is not operational.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-5-FIRMWARE_SWITCH

5-Notice

Firmware switchover initiated for modem in slot [dec]/[dec]

Firmware switchover caused by user request.

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-MNO_SWITCH

5-Notice

MNO switchover initiated for modem in slot [dec]/[dec]

MNO switchover caused by user request.

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-MODEM_BOOT_READY

5-Notice

Modem in slot [dec]/[dec] is in Boot Ready Mode.. Please perform FW upgrade

The cellular modem is not operational.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-UNSUPPORTED_CELLULAR_NIM

2-Critical

Unsupported Cellular NIM inserted in slot [dec]/[dec]

This NIM is not supported for the current software release

esg-lte

"Please contact TAC for supported software release for this NIM"

CELLWAN-2-DYING_GASP_NOT_SUPPORTED

2-Critical

Dying Gasp Feature is not supported in Cellular slot [dec]/[dec]

This NIM is not supporting Dying Gasp Feature.

esg-lte

"Please contact TAC for Dying Gasp Feature Supported NIM"

CELLWAN-2-MODEM_INIT_TIMEOUT

2-Critical

Cellular modem initialization timeout for [chars]

Modem failed to initialize.

esg-lte

LOG_STD_SH_TECH_ACTION

CELLWAN-2-MICRO_DNLD_START_FAIL

2-Critical

\nModem returned following error to Download Start Request:[chars]

Modem Firmware Download Start Request Failed. It generally means that firmware binary file is wrong.

esg-lte

"show flash:<noCmdBold> command " "and <CmdBold>show controller cellular x/x/x all"

CELLWAN-2-MICRO_FW_DNLD_FAIL

2-Critical

\nModem returned following error to Download Request:[chars]

Modem Firmware Download Continue Request Failed. It generally means that firmware binary file is corrupt.

esg-lte

"show flash:<noCmdBold> command " "and <CmdBold>show controller cellular x/x/x all"

CELLWAN-2-MICRO_DNLD_END_FAIL

2-Critical

\nModem returned following error to Download End Request:[chars]

Modem Firmware Download End Request Failed

esg-lte

"show flash:<noCmdBold> command " "and <CmdBold>show controller cellular x/x/x all"

CELLWAN-2-MICRO_FLASH_PRGM_FAIL

2-Critical

\nModem returned following error to Flash Program Request:[chars]

Modem failed to launch the new firmware.

esg-lte

"show flash:<noCmdBold> command " "and <CmdBold>show controller cellular x/x/x all"

CELLWAN-2-SIM_FAILURE

2-Critical

[[chars]]: SIM read failed [chars]

If the SIM is not present insert SIM in the SIM socket. If error still persists SIM needs to be replaced.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_LOCKED

2-Critical

[[chars]]: SIM is locked [chars]

SIM is locked and no data call can be made till it is unlocked.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_REJECTED

2-Critical

[[chars]]: SIM rejected by the network [chars]

The SIM is not valid to be used in the network. A new valid SIM needs to be inserted in the SIM socket.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_CHV1_BLOCKED

2-Critical

[[chars]]: SIM is blocked. PUK is required to unblock the SIM [chars]

SIM is blocked and no data call can be made until it is unblocked using PUK.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_MEP_LOCKED

2-Critical

[[chars]]: Invalid SIM or device locked to carrier [chars]

Invalid SIM or device locked to carrier

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_CHV1_CONFIG_REMOVED

2-Critical

[[chars]]: CHV1 verfication failed [chars] : Incorrect PIN configured. Erased the CHV1 code from router runnning configuration to avoid SIM blocking during modem reset/powercycle. \n!!!WARNING: If the incorrect PIN is saved in router start-up configuration please remove it manually to avoid SIM blocking during router reload

SIM CHV1 verfication failed. Incorrect PIN configured.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_SECURITY_SHUTDOWN

2-Critical

[[chars]]: CHV1 PIN is configured while SIM is unlocked [chars]. Shutting down all PDP interfaces

CHV1 is configured while SIM is unlocked The SIM is not valid to be used in the network. A new valid locked SIM needs to be inserted in the SIM socket.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-SIM_NOT_READY

2-Critical

[chars] Modem is not ready. SIM status may be not current.

SIM access cannot be granted or may return an error when : 1 The modem is not up or during a reset.

esg-lte

"1 Wait till MODEM UP message is seen from the console before accessing SIM."

CELLWAN-2-SIM_NOT_PRESENT

2-Critical

[[chars]]: SIM is not present in Slot [dec]

SIM has not been detected in the NIM SIM socket

esg-lte

"Insert a valid sim in the NIM SIM socket."

CELLWAN-6-SIM_PRESENT

6-Information

[[chars]]: SIM is present in Slot [dec]

SIM has been detected in the SIM socket

esg-lte

"No action"

CELLWAN-6-SIM_INSERTED

6-Information

[[chars]]: SIM in slot [dec] has been \n\ inserted

SIM is inserted to the slot.

esg-lte

"No action"

CELLWAN-6-SIM_REMOVED

6-Information

[[chars]]: WARNING: SIM in slot [dec] has \n\ been removed

SIM is removed from the slot.

esg-lte

"No action"

CELLWAN-2-SIM_SWITCH_FAILURE

2-Critical

[[chars]]: Failed to switch to SIM slot [dec] !!

Failed to switch to the requested NIM SIM slot

esg-lte

"Examine SIM in the indicated slot"

CELLWAN-5-SIM_DETECT_START

5-Notice

[[chars]]: SIM presence detection starts !!

SIM presence detection has started

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SIM_DETECT_COMPLETE

5-Notice

[[chars]]: SIM presence detection has completed !!

SIM presence detection has completed

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SIM_ACTIVATION

5-Notice

[[chars]]: SIM slot [dec] is being activated !!

The request to activate the indicated SIM slot has been sent to the modem

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SIM_ACTIVE

5-Notice

[[chars]]: SIM slot [dec] is Active !!

The indicated SIM slot is active.

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SIM_ACTIVATION_TIMEOUT

5-Notice

[[chars]]: SIM slot [dec] activation request timeout !!

Timeout on the request sent to the modem to activate the indicated SIM slot

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SIM_ACQUISITION_TIMEOUT

5-Notice

[[chars]]: SIM slot [dec] Acquisition Timer timeout !!

Timeout on the SIM slot acquisition timer initiate sim switching request to the alter SIM slot

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SIM_FAILOVER_TIMEOUT

5-Notice

[[chars]]: SIM slot [dec] Failover Timer timeout !!

Timeout on the SIM slot failover timer initiate sim switching request to the alter SIM slot

esg-lte

LOG_STD_NO_ACTION

CELLWAN-2-INTERFACE_GOING_DOWN

2-Critical

[chars] is being shutdown temporarily due to authentication failure for [dec] secs.

The interface is being shutdown because the call could not be connected due to PPP authentication failures. The interface will be brought up after the specified time. This is to prevent frequent calls being attempted if authentication problems are not fixed.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_NI_ALERT

2-Critical

[[chars]]: OMA DM NI Alert is received for [chars] \nPlease execute 'cellular <unit> cdma activate oma-dm ni-alert [allow | deny]'

OMA DM Network-Initiated alert is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_NO_OP

2-Critical

[[chars]]: OMA DM [chars] could not be completed. \nPlease try again later. If the problem persists you may need to contact Customer Service.

OMA DM session state is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_ERROR

2-Critical

[[chars]]: OMA DM [chars] Failed - Error:0x[hec][chars]

OMA DM session state is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_HFA_PENDING

2-Critical

[[chars]]: OMA DM [chars] waiting for retry in [dec] seconds

OMA DM session state is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_ACTIVE

2-Critical

[[chars]]: OMA DM [chars] session is active

OMA DM session state is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_SUCCESS

2-Critical

[[chars]]: OMA DM [chars] completed successfully

OMA DM session state is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-OMA_DM_NO_PRL

2-Critical

[[chars]]: OMA DM - No PRL update available

OMA DM session state is received by modem

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-POWER_SAVE_MODE

2-Critical

[[chars]]: is in Power save mode. Command ignored.

radio is currently OFF on this NIM

esg-lte

LOG_STD_ACTION

CELLWAN-5-SMS_SERVICE_AVAILABLE

5-Notice

[chars] SMS service is now available.

You can send and receive text messages on this cellular interface

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SMS_SERVICE_UNAVAILABLE

5-Notice

[chars] SMS service is now unavailable.

You can not send and receive text messages on this cellular interface

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-INCOMING_SMS

5-Notice

[chars] has just received new incoming SMS.

New incoming text messages arrived at cellular interface

esg-lte

"Please do 'cellular <unit> gsm|cdma sms view' to read SMS"

CELLWAN-5-OUTGOING_SMS_SENT

5-Notice

[chars] has just sent an outgoing SMS successfully.

Outgoing text message was sent successfully from cellular interface

esg-lte

LOG_STD_NO_ACTION

CELLWAN-4-OUTGOING_SMS_ERROR

4-Warning

[chars] failed to send an outgoing SMS.

Outgoing text message failed to send from cellular interface

esg-lte

"Please do 'show cellular <unit> sms' to see " "error code"

CELLWAN-4-OUTGOING_SMS_SERV_UNAVAIL

4-Warning

[chars] can't send an SMS because SMS service is not available.

Text message service is not available on specified cellular interface

esg-lte

"Check modem is powered up radio is not in power " "saving mode and SIM is inserted"

CELLWAN-2-SMS_ARCH_PATH_UNCONFIGURED

2-Critical

[chars] failed to archive SMS because 'gsm|cdma|lte sms archive path' under cellular controller is not configured.

'gsm|cdma|lte sms archive path' under cellular controller must be configured first before background incoming text message archive can function properly

esg-lte

"Configure 'gsm|cdma|lte sms archive path' under cellular controller"

CELLWAN-5-SMS_INBOX_ARCH_DONE

5-Notice

[chars] has just archived all incoming SMS to FTP server successfully.

Incoming text messages were archived to FTP server successfully from cellular interface

esg-lte

LOG_STD_NO_ACTION

CELLWAN-2-SMS_INBOX_ARCH_OPEN_ERROR

2-Critical

[chars] failed to open [chars] to archive incoming SMS.

Incoming text messages archive to FTP server failed because the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller can not be opened

esg-lte

"Please check that the FTP server configured under cellular " "controller is reachable and that the directory exists"

CELLWAN-2-SMS_INBOX_ARCH_WRITE_ERROR

2-Critical

[chars] failed to write [chars] to archive incoming SMS.

Incoming text messages archive to FTP server failed because of write error to the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller

esg-lte

"Please check that the FTP server configured under cellular " "controller with 'gsm|cdma|lte sms archive path' is reachable and " "has enough storage space"

CELLWAN-5-SMS_INBOX_MSG_ARCH_DONE

5-Notice

[chars] has just archived an incoming SMS to FTP server successfully.

An incoming text message was archived to FTP server successfully from cellular interface

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SMS_OUTBOX_ARCH_DONE

5-Notice

[chars] has just archived an outgoing SMS to FTP server successfully.

An outgoing text message was archived to FTP server successfully from cellular interface

esg-lte

LOG_STD_NO_ACTION

CELLWAN-2-SMS_OUTBOX_ARCH_OPEN_ERROR

2-Critical

[chars] failed to open [chars] to archive an outgoing SMS.

Outgoing text message archive to FTP server failed because the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller can not be opened

esg-lte

"Please check that the FTP server configured under cellular " "controller is reachable and that the directory exists"

CELLWAN-2-SMS_OUTBOX_ARCH_WRITE_ERROR

2-Critical

[chars] failed to write [chars] to archive an outgoing SMS.

Outgoing text message archive to FTP server failed because of write error to the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller

esg-lte

"Please check that the FTP server configured under cellular " "controller with 'gsm|cdma|lte sms archive path' is reachable and " "has enough storage space"

CELLWAN-4-CELLULAR_FW_UNSUPPORTED

4-Warning

[chars]: Unsupported or older modem firmware [chars] detected please upgrade modem to supported firmware of at least [chars]

The current firmware on specified cellular interface is not supported. Any actions and errors that occur will not be supported until the fw is upgraded to at least the version requested

esg-lte

"Please upgrade to the latest FW from online using" " 'microcode reload'"

CELLWAN-2-DMLOG_FILTER_FILE_OPEN_ERROR

2-Critical

[chars] failed to open [chars] to read DM log filter.

Failed to open filter file from the location configured with 'gsm|cdma|lte modem dm-log filter' under cellular controller

esg-lte

"Please check that the path configured under cellular " "controller is reachable"

CELLWAN-2-DMLOG_OUTPUT_FILE_OPEN_ERROR

2-Critical

[chars] failed to open [chars] to archive DM log files.

Saving DM packets to file system failed. Output file URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller can not be opened

esg-lte

"Please check that the path configured under cellular " "controller is reachable"

CELLWAN-2-DMLOG_OUTPUT_WRITE_ERROR

2-Critical

[chars] failed to write [chars] DM packets to configured file system

Saving DM packets to file system failed because of write error to the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller

esg-lte

"Please check that the URL configured under cellular " "controller with 'gsm|cdma|lte modem dm-log output path' " "is reachable and has enough storage space"

CELLWAN-2-DMLOG_OUTPUT_SPACE_FULL

2-Critical

[chars] DM log file storage is full!

Saving DM packets to file system failed because there is no more space left on the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller

esg-lte

"Please delete existing log files from the specified URL " "'gsm|cdma|lte modem dm-log output path' or upload them " "to the server then re-enable logging."

CELLWAN-5-DMLOG_AUTOSTOP_TRIGGER

5-Notice

[chars]: DM logging will be stopped in [dec] [chars] autostop trigger event [chars] set

DM log autostop trigger event configured DM logging will be stopped after the timer expiry

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-DMLOG_AUTOSTOP_TIMER_EXPIRY

5-Notice

[chars]: DM logging stopped

DM logging is stopped due to autostop trigger timer expiry

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-DMLOG_AUTOSTOP_TIMER_CANCEL

5-Notice

[chars]: DM logging autostop timer canceled

DM logging autostop timer is canceled

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-DMLOG_DISABLE_OIR

5-Notice

[chars]: OIR Detected. DM logging stopped

DM logging is stopped due to OIR

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-DMLOG_DISPLAY_OUTPUT_PATH_EXTERN

5-Notice

DM log output path = bootflash:/core/modules

DM log output path set to bootflash:/core/modules

esg-lte

""

CELLWAN-5-DMLOG_DISPLAY_OUTPUT_PATH_INTEGRATED

5-Notice

DM log output path = bootflash:

DM log output path set to bootflash:/

esg-lte

""

CELLWAN-2-SVBLOG_OUTPUT_FILE_OPEN_ERROR

2-Critical

[chars] failed to open [chars] to archive SVB log files.

Saving SVB packets to file system failed. Output file URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller can not be opened

esg-lte

"Please check that the path configured under cellular " "controller is reachable"

CELLWAN-2-SVBLOG_OUTPUT_WRITE_ERROR

2-Critical

[chars] failed to write [chars] SVB packets to configured file system

Saving SVB packets to file system failed because of write error to the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller

esg-lte

"Please check that the URL configured under cellular " "controller with 'gsm|cdma|lte modem dm-log output path' " "is reachable and has enough storage space"

CELLWAN-2-SVBLOG_OUTPUT_SPACE_FULL

2-Critical

[chars] SVB log file storage is full!

Saving SVB packets to file system failed because there is no more space left on the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller

esg-lte

"Please delete existing log files from the specified URL " "'gsm|cdma|lte modem dm-log output path' or upload them " "to the server then re-enable logging."

CELLWAN-5-SVBLOG_AUTOSTOP_TRIGGER

5-Notice

[chars]: SVB logging will be stopped in [dec] minutes autostop trigger event [chars] set

SVB log autostop trigger event configured SVB logging will be stopped after the timer expiry

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SVBLOG_AUTOSTOP_TIMER_EXPIRY

5-Notice

[chars]: SVB logging stopped

SVB logging is stopped due to autostop trigger timer expiry

esg-lte

LOG_STD_NO_ACTION

CELLWAN-5-SVBLOG_AUTOSTOP_TIMER_CANCEL

5-Notice

[chars]: SVB logging autostop timer canceled

SVB logging autostop timer is canceled

esg-lte

LOG_STD_NO_ACTION

CELLWAN-2-WCDMA_ALL_BAND_UNDEFINED

2-Critical

[[chars]]: wcdma-all band not supported

wcdma-all band is not supported by modem or not defined

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-CALL_SETUP_FAIL

2-Critical

[chars] data call setup failed due to [chars].

Data call setup failed because the IP address configured under cellular interface does not match the IP address assigned by the network

esg-lte

"Please check the IP address configuration under cellular" "interface"

CELLWAN-2-MDM_LINK_FAILURE

2-Critical

[chars] direct IP synchronization process fails after [dec] attempts

Direct IP synchronization fails to come up after maximum number of attempts.

esg-lte

"Contact customer service if the problem persists."

CELLWAN-3-GPS_FAIL_START_TRACK

3-Error

[[chars]] GPS failed to start tracking - [chars] [0x[hec]] please try again

Modem failed to enable GPS mode due to error indicated. Fix that error and try again.

esg-lte

"Fix error indicated and try enabling GPS again."

CELLWAN-3-GPS_FAIL_END_SESSION

3-Error

[[chars]] GPS failed to end location fix session - [chars] [0x[hec]] please try again

Modem failed to disable GPS mode due to error indicated. Fix that error and try again.

esg-lte

"Fix error indicated and try disabling GPS again."

CELLWAN-2-GSM_PROFILE_UNDEFINED

2-Critical

[[chars]]: Default profile [dec][chars] does not exist. Please execute 'cellular <unit> gsm profile create <profile #>' to create the profile.

Default profile is undefined. the profile does not exist because it is not defined or is deleted.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-3-GSM_PROFILE_CREATION_FAILURE

3-Error

[[chars]] GSM profile creation fails - [chars] [0x[hec]] please try again

Modem failed to create the GSM profile due to error indicated. Fix that error and try again.

esg-lte

"Fix error indicated and try creating GSM profile again."

CELLWAN-2-MODEM_TIMEOUT

2-Critical

Modem in [chars] not responding

The cellular modem is not responding.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-4-CELLULAR_MODEM_SKU_MISMATCH

4-Warning

[chars]: Mismatch detected between installed modem [chars][SKU ID [chars]] on SKU type [chars]. Expected modem for this SKU is [chars][SKU ID [chars]]

Incorrect modem type has been installed on this SKU. Any actions and issues caused by it will not be supported

esg-lte

"Please contact the cisco customer service" "to replace the card"

CELLWAN-1-POOL_INIT_FAIL

1-Alert

cellular pool init failed for subslot [dec]/[dec] \ pool name [chars]

The NIM cellular pool init failed for this module.

esg-lte

"show cellular x/x/x all<noCmdBold> command " "and <CmdBold>show tech-support"

CELLWAN-2-QOS_ENABLED

2-Critical

QoS Feature in [chars] is now activated

QoS Feature is now enabled and activated in the modem.

-

"QoS Feature is now enabled and activated in the modem."

CELLWAN-2-QOS_NW_STATUS

2-Critical

Network status for QoS feature is [chars] in [chars].

Network status for QoS feature is either enabled or disabled by the carrier.

-

"check with carrier if you expect QoS feature but it is disabled"

CELLWAN-2-QOS_PRI_EVENT_STATUS

2-Critical

QoS Event Status = [dec] for default bearer in [chars] in [chars].

QoS Event Status for default bearer for the cellular interface.

-

"check with carrier to see if the default bearer" " config is changed"

CELLWAN-2-BEARER_UP

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is now UP

default/dedicated bearer has been added.

-

"Check the TFT rules of the dedicated bearer by doing show cellular" " and configure the host QOS configuration to match the TFT rules"

CELLWAN-2-BEARER_DOWN

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is now down.

default/dedicated bearer has been deleted.

-

"Host QOS configuration may need to be modified" " to match the modem configuration"

CELLWAN-2-BEARER_DELETED

2-Critical

[chars] bearer bearer_id=[dec] in [chars] is now deleted.

default/dedicated bearer has been deleted.

-

"Host QOS configuration may need to be deleted" " to match the modem configuration"

CELLWAN-2-BEARER_SUSPENDED

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars]

default/dedicated bearer has been suspended.

-

"Host QOS configuration may need to be suspended" " to match the modem configuration"

CELLWAN-2-BEARER_MODIFIED

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] configuration in [chars] is modified

default/dedicated bearer configuration has been modified.

-

"Check the TFT rules of the dedicated bearer by doing" " show cellular and configure the host QOS" " configuration to match the TFT rules"

CELLWAN-2-BEARER_CONGESTION_ON

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is congested

Traffic congestion present in the dedicated bearer. If it does not clear make sure the host QOS configuration matches the dedicated bearer configuration

-

"Check the MBR of the dedicated bearer by doing show " "cellular and configure the host QOS configuration " "to match MBR of the dedicated bearer."

CELLWAN-2-BEARER_CONGESTION_OFF

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is NOT congested now

Traffic congestion has cleared in the dedicated bearer

-

"No action is needed"

CELLWAN-2-DEDICATED_BEARER_STATUS_UNKNOWN

2-Critical

Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] configuration in [chars] is

Dedicated bearer configuration status is unknown.

-

"Check the TFT rules of the dedicated bearer by doing" " show cellular and report the TFT rules to the " "carrier."

CELLWAN-4-MANUAL_PLMN_SELECTION_FAILED

4-Warning

Manual/Force PLMN Selection Failed. [chars]

Manual/Force PLMN Selection Failed

-

"Please use Different PLMN or check number of MNC Bits " "in PLMN Selection"

CELLWAN-4-DG_SMS_CONFIG_FAILED

4-Warning

Dying Gasp SMS Configuration Failed. [chars]

Dying Gasp SMS Configuration Failed.

-

"Please try Dying Gasp SMS Configuration later"

CELLWAN-4-DG_DETACH_CONFIG_FAILED

4-Warning

Dying Gasp Detach Configuration Failed. [chars]

Dying Gasp Detach Configuration Failed.

-

"Please try Dying Gasp Detach Configuration later"

CELLWAN-4-MODEM_RESTART_IND

4-Warning

[chars] Modem restart [chars]

Modem Restart Indication

-

"No action is needed"

CELLWAN-4-MODEM_COMM_FAIL

4-Warning

Communication between Modem and IOS failed: [chars]

Communication between Modem and IOS Failed

-

" Modem Reset will recover "

CELLWAN-6-CELLULAR_BACKOFF_START

6-Information

[chars]: Cellular back-off has started on PDN [dec]

Back off has started because of certain error codes from network side

-

""

CELLWAN-6-CELLULAR_BACKOFF_STOP

6-Information

[chars]: Cellular back-off has stopped on PDN [dec]

Back off has stopped

-

""

CELLWAN-6-CELLULAR_NETWORK_ATTACH_FAILURE

6-Information

[chars]: Cellualr network attachment failure. Reject Cause [dec] [chars].

Network attachment failure

-

"Check 3GPP Table 10.5.95/3GPP TS 24.008 for information"

CELLWAN-2-LINK_RECOVERY

2-Critical

[chars]: Cellular Modem has been power cycled : [chars]

Link Recovery Process has detected an inconsistent state of the modem

-

""

CELLWAN-2-DYING_GASP_POWER_FAILURE

2-Critical

Dying Gasp SMS will not be sent out by Modem in slot [dec]/[dec] due to standby power failure. Please contact TAC.

Modem doesn't have enough power to send Dying Gasp SMS

esg-lte

"Please contact TAC"

CELLWAN-2-DYING_GASP_POWER_SUCCESS

2-Critical

Modem in slot [dec]/[dec] has sufficient power to send Dying Gasp SMS

Modem has sufficient power to send Dying Gasp SMS

esg-lte

"No action is needed"

CELLWAN-2-CRASHDUMP_SUCCESS

2-Critical

[chars]:Crashdump successfully logged in /bootflash/

Cellular Modem Crashdump files successfully logged to local flash.

esg-lte

""

CELLWAN-6-FOTA_DNLD_STARTED

6-Information

[[chars]]: Firmware download started in cellular slot [dec]/[dec]

FOTA Cellular modem firmware download started.

esg-lte

""

CELLWAN-6-FOTA_DNLD_COMPLETE

6-Information

[[chars]]: Firmware has been downloaded for modem in cellular slot [dec]/[dec]

FOTA Cellular modem firmware download started.

esg-lte

""

CELLWAN-6-FOTA_UPGRADE_STARTED

6-Information

[[chars]]: Firmware upgrade started in cellular slot [dec]/[dec]. Modem will reset and come up with new firmware.

FOTA Cellular modem firmware upgraded started.

esg-lte

""

CELLWAN-6-FOTA_UPGRADE_SUCESS

6-Information

[[chars]]: Firmware upgrade successful in cellular slot [dec]/[dec]

FOTA Cellular modem firmware upgraded successfully.

esg-lte

""

CELLWAN-6-FOTA_UPGRADE_TIMEOUT

6-Information

[[chars]]: Firmware upgrade timed out in cellular slot [dec]/[dec]

FOTA Cellular modem firmware upgrade timed out.

esg-lte

""

CELLWAN-5-NULL_BEARER

5-Notice

NULL Bearer Timer [chars]:Current NULL Bearer count:[dec]:Total NULL Bearer count:[dec]:Profile id:[dec]:PDN ID:[dec]

NULL Bearer notification from modem. No action is required

esg-lte

LOG_STD_NO_ACTION

SERIAL_12IN1-3-SPI4_ERR

3-Error

SPA [dec]/[dec]: [chars] was encountered. Intr status: 0x[hec]\n

The SPA driver detected a Hardware error condition on the SPA card. This might result in improper operation.

-

"The SPA driver has encountered a Hardware error on the SPA's SPI4 bus. " "Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SERIAL_12IN1-1-CLOCKRATE

1-Alert

[chars]:Link has been brought [chars] due to clock rate change threshold configured = [dec] received clock rate = [dec]

The received clock rate is changed from below the threshold\n\ configured to above or vice versa..

spa-4t

"Check the received clock rate from the provider end and the " "clockrate threshold configuration if the clock rate goes " "below the threshold configured interface is brought down"

SERIAL_12IN1-3-SW_ERR

3-Error

[chars]: A software error was encountered at [chars]: [chars]\n

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-4t

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SERIAL_12IN1-3-SW_ERR_1

3-Error

[chars]: A software error was encountered at [chars]: [chars] 0x[hec]\n

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-4t

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SERIAL_12IN1-3-SW_ERR_2

3-Error

[chars]: A software error was encountered at [chars]: [chars] 0x[hec]/0x[hec]\n

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-4t

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SERIAL_12IN1-3-SPI4_HW_ERR

3-Error

SPA [dec]/[dec]: [chars] was encountered.\n

The SPA driver detected a Hardware error condition on the SPA card. This might result in improper operation.

-

"The SPA driver has encountered a Hardware error on the SPA's SPI4 bus." "Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

SERIAL_12IN1-1-CLOCKRATE

1-Alert

[chars]:Link has been brought [chars] due to clock rate change threshold configured = [dec] received clock rate = [dec]

The received clock rate is changed from below the threshold\n\ configured to above or vice versa..

spa-4t

"Check the received clock rate from the provider end and the" " clockrate threshold configuration if the clock rate goes" " below the threshold configured interface is brought down"

SERIAL_12IN1-3-SW_ERR

3-Error

[chars]: A software error was encountered at [chars]: [chars]\n

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

-

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and" "open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

SERIAL_12IN1-3-SW_ERR_1

3-Error

[chars]: A software error was encountered at [chars]: [chars] 0x[hec]\n

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

-

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and" "open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

CARD_PROTECTION-4-CONFIG_GROUP

4-Warning

CARD_PROTECTION-Group [dec] is configured

Card Protection group is configured

-

"None - normal situation"

CARD_PROTECTION-4-CONFIG_VIRTUAL

4-Warning

Virtual IM [dec]/[dec] is created

Virtual IM is created for Card protection group

-

"None - normal situation"

CARD_PROTECTION-4-CONFIG_ADD

4-Warning

[chars] [dec]/[dec] Member added to Card protection group [dec]

New Member added to Card protection group

-

"None - normal situation"

CARD_PROTECTION-4-PROTECTION

4-Warning

Card protection group: [dec] [chars] [dec]/[dec] is [chars] [chars]

Protection Switchover between members of group

-

"None - normal situation"

CARD_PROTECTION-4-ACTIVE

4-Warning

Card protection group: [dec] is [chars] ACTIVE [chars]

whether card protection group is ACTIVE

-

"None - normal situation"

CARD_PROTECTION-3-BOTH_ACTIVE

3-Error

For Card protection group: [dec] both primary and backup are active

DS1844 potentiometer initialization failed. It indicates a hardware failure

gsr-oc3_12-pos-spa

"Change the hardware or copy the error message exactly as it " "appears and report it to your technical support representative."

MSG_POS_OC3_OC12_SPA-3-RESOURCE_ERROR

3-Error

[chars] 0x[hec] 0x[hec] 0x[hec] [chars]

Tranceiver analyze failed

gsr-oc3_12-pos-spa

"Remove the tranceiver module and insert a valid module " "with rate that is supported on the SPA."

SPA_WMA-3-WMA_SW_ERR

3-Error

NULL

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-wma

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

SPA_CHOC_DSX-4-UNPROV_FAIL

4-Warning

Interface [chars] unprovisioning failed: [chars]

The system failed to respond to an unprovisioning command. A hidden VLAN could not be deleted within a 2 second timeout window. This condition may be caused by a system that is too busy or by a FIB IPC failure. The line card driver code will attempt to delete the hidden VLAN.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

"If processing continues normally no action is required. If " "system operation is adversely affected " LOG_STD_ACTION

SPA_CHOC_DSX-3-NODESTROYSUBBLOCK

3-Error

The [chars] subblock named [chars] was not removed

IDB sub-blocks could not be removed during the unprovisioning of a channel. This condition indicates a software error.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_ACTION

SPA_CHOC_DSX-3-AUTODNR

3-Error

[chars] failed for slot [dec] bay [dec]

AUTODNR/USNDNR process has failed. The SPA and SIP are out of synchronization. This condition indicates a software error.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_ACTION

SPA_CHOC_DSX-3-UNKNOWN_CMD

3-Error

Unknown [chars] command recieved on slot/bay:[dec]/[dec]. Command Type = [dec]

An unknown command was recieved by the SPA card carrier

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_ACTION

SPA_CHOC_DSX-3-INVLIAD_IF_INDEX

3-Error

Invalid interface index [dec] on slot/bay:[dec]/[dec]. Min. Index = [dec]. MAx. Index = [dec].

The index is not valid for the interface specified in the error message.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_ACTION

SPA_CHOC_DSX-3-NULL_DATA_STRUCTURE

3-Error

Failed to create [chars] on slot/bay:[dec]/[dec]. Port Number = [dec].

The software resource can not be allocated for this hardware

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_ACTION

SPA_CHOC_DSX-3-INVALID_IF_TYPE

3-Error

Invalid SPA type [dec] on [chars]. Port Number = [dec].

The software can not recognize the interface type

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_ACTION

SPA_CHOC_DSX-3-NULL_SPA_PTR

3-Error

-

The pointer to an SPA value is of a null value.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-NULL_VIRT_SPA_PTR

3-Error

[chars]

Pointer to virtual SPA object is NULL in card prot grp.

asr900-dsx-cp

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-SPA_CMD_SEND_ERR

3-Error

Failed to send [chars] command to SPA

The host failed to send a command to SPA

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-SPA_CMD_RETURN_ERR

3-Error

SPA command [chars] return error [dec]

The SPA returned an error status for a host command

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-EFC_ERROR

3-Error

EFC ERROR: [chars] - [chars] [dec]

The SPA Extended Flow Control encountered an error

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-T3CFG_ERROR

3-Error

Interface [chars] T3 [dec] config command error cmd [dec] arg [dec] retval [dec]

A command sent from the system to a linecard has failed.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-T1CFG_ERROR

3-Error

Interface [chars] T3 [dec] T1 [dec] config command error cmd [dec] arg [dec] retval [dec]

A command sent from the system to a linecard has failed.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

LOG_STD_SH_TECH_ACTION

SPA_CHOC_DSX-3-VCCFG_ERROR

3-Error

Interface [chars] config command error cmd [dec] arg [dec] retval [dec]

A command sent from the system to a linecard has failed.

spa-ct3-ds0 for CT3 spa-choc3-ds0 for CHOC-3/STM-1

"This is an internal software error. Decode the " "traceback and get the output of the <CmdBold>show " "logging<NoCmdBold> command on RP and SIP and check " "if there are any errors being reported. Try to " "recreate the problem to see if there is a " "consistant method to recreate. Check the Bug " "Toolkit before contacting TAC. When contacting TAC " "provide the above information along with the " "output of the <CmdBold>show tech-support<NoCmdBold> " "command."

SPA_CHOC_DSX-3-LINK_TABLE_ERR

3-Error

[chars]: Could not create link table error [dec]

Error creating link record table. Interfaces may not come up / pass traffic.

spa-ser-te1 for T1/E1 spa-ct3-ds0 for CT3 and spa-choc3-ds0 for CHOC-3/STM-1

"If the ports on the SPA are not operating as expected power down and" "reseat the indicated SPA card. " "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-UNCOR_MEM_ERR

3-Error

SPA [dec]/[dec]: [dec] uncorrectable [chars] memory errors encountered.\n

The SPA driver detected an uncorrectable memory error condition on the SPA card. Packet corruption may result.

spa-ser-te1 for T1/E1 spa-ct3-ds0 for CT3 and spa-choc3-ds0 for CHOC-3/STM-1

"The SPA driver has encountered an uncorrectable memory error on the SPA " "card. The hexadecimal memory address of the most recent error is " "specified in the message text on the console or in the system log. " "Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-BAD_SIZE_ERR

3-Error

SPA [dec]/[dec]: [dec] [chars] events on HDLC Controller were encountered. The SPA is being restarted.\n

The SPA driver detected an error event on the HDLC controller.

spa-ser-te1 for T1/E1 spa-ct3-ds0 for CT3 and spa-choc3-ds0 for CHOC-3/STM-1

"The SPA driver has encountered an error event on the SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-HDLC_CTRL_ERR

3-Error

SPA [dec]/[dec]: [dec] [chars] events on HDLC Controller were encountered.

The SPA driver detected an error event on the HDLC Controller.

spa-ser-te1 for T1/E1 spa-ct3-ds0 for CT3 and spa-choc3-ds0 for CHOC-3/STM-1

"The SPA driver has encountered an error event on the SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold>" "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-COR_MEM_ERR

3-Error

SPA [dec]/[dec]: [dec] correctable [chars] memory errors encountered.\n

The SPA driver detected a correctable memory error on the SPA card.

spa-ser-te1 for T1/E1 spa-ct3-ds0 for CT3 and spa-choc3-ds0 for CHOC-3/STM-1

"The SPA has encountered a correctable memory error on the SPA card. " "The error has been corrected and normal processing should continue. " "The hexadecimal memory address of the most recent error is specified " "in the message text on the console or in the system log. " "If the condition persists or other errors are indicated for the SPA " "copy the error message exactly as it appears. Then power down and " "reseat the indicated SPA card. Next research and attempt " "to resolve the issue using the SPA hardware troubleshooting " "documentation as well as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-UNCOR_PARITY_ERR

3-Error

SPA [dec]/[dec]: [dec] [chars] parity errors encountered.\n

The SPA driver detected an uncorrectable parity error condition on the SPA card. Packet corruption may result.

spa-ser-te1 for T1/E1 spa-ct3-ds0 for CT3 and spa-choc3-ds0 for CHOC-3/STM-1

"Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-SPI4_HW_ERR

3-Error

SPA on [chars]: [chars] Hardware error was encountered.\n

The SPA driver detected a Hardware error condition on the SPA card. This might result in improper operation.

-

"The SPA driver has encountered a Hardware error on the SPA's SPI4 bus. " "Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-SPA_SW_ERR

3-Error

SPA on [chars]: [chars] Software error was encountered.\n

The SPA driver detected a Software error condition on the SPA card. This might result improper operation.

-

"The SPA driver has encountered a Software error. " "Please first reload the configuration by doing shut/no shut on " "the controllers. If the problem persists please power cycle the SPA. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the Bug Toolkit on the Cisco web-site. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-SEMAHOG

3-Error

SPA on [chars]: Semaphore Hog was encountered.Hogged by process [chars]\n

The semaphore used by the IPC communication between host and the SPA was hogged by one process. This behavior would cause other processes fail to send commands down to the SPA. This might result improper operation.

-

"Please first stop all the traffic on the SPA and then " "reload the configuration by doing shut/no shut on " "the controllers. If the problem persists please power cycle the SPA. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the Bug Tookit " "on the Cisco web-site. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a <CmdBold>tech-support<NoCmdBold> " "to your support representative or attach it to your case in non-zipped " "plain text format .txt."

SPA_CHOC_DSX-3-PERIODIC_PROCESS

3-Error

[chars]: periodic process error [chars].

The SPA driver detected an error with the periodic processing routine.

spa-ser-te1

"If the ports on the SPA are not operating as expected take it out of " "service by issuing command <CmdBold>hw-module subslot " "<noCmdBold><CmdArg>slot#/bay#<noCmdArg><CmdBold> stop<NoCmdBold> " "followed by <CmdBold>hw-module subslot " "<noCmdBold><CmdArg>slot#/bay#<noCmdArg><CmdBold> start<NoCmdBold> for " "the indicated SPA card. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve the " "issue using the SPA hardware troubleshooting documentation as well as " "the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative."

SPA_CHOC_DSX-3-DPIDX_LKUP_ERR

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

asr900-tdm-combo

LOG_STD_NO_ACTION

SPA_CHOC_DSX-3-PROCESS_FAIL

3-Error

process creation failed in [chars] spa type [chars] for [chars]

The Periodic one second process creation failed. This indicates a software error.

asr900-tdm-combo

LOG_STD_ACTION

SPA_CHOC_DSX-5-CHNL_GRP_ADD

5-Notice

Channel Group created on the interface [chars]\n

Channel Group created on the serial interface.

asr900-3g-ms

LOG_STD_ACTION

SPA_CHOC_DSX-5-CHNL_GRP_DEL

5-Notice

Channel Group delete from the interface [chars]\n

Channel Group deleted from the serial interface.

asr900-3g-ms

LOG_STD_ACTION

SPA_T3E3-5-BERT

5-Notice

Interface [chars] BERT [chars]

The spa t3e3 driver processed a BERT task.

spa-ser-t3e3

"None this is just a notification upon completion of a BERT task."

SPA_T3E3-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed

spa-ser-t3e3

"Inform the network operator that subrate configuration changed by\n\ remote end"

SPA_T3E3-3-MSGERR

3-Error

Illegal message type [dec] received for Interface [chars]

An unknown message was received by RP.

spa-ser-t3e3

LOG_STD_SH_TECH_ACTION

SPA_T3E3-3-NO_SSB

3-Error

[chars]: Failed to get serial subblock.

Serial subblock pointer is NULL. Internal software error.

spa-ser-t3e3

LOG_STD_SH_TECH_ACTION

SPA_T3E3-3-SSBINIT

3-Error

[chars]: Fail to initialize serial IDB

Most common reason is lack of system memory. Earlier messages might indicate memory allocation failures.

spa-ser-t3e3

LOG_STD_SH_TECH_ACTION

SPA_T3E3-3-LOVEFAIL

3-Error

[chars]: failed to send [chars] love letter

A love letter status or configuration message could not be sent.

spa-ser-t3e3

LOG_STD_SH_TECH_ACTION

SPA_T3E3-5-MSG_QUEUE_ERR

5-Notice

[chars]: T3E3 process message queue not initialized.

The T3E3 process message queue is not ready.

-

"Copy the error message exactly as it appears collect the output " "of 'show tech-support' command immediately and report it to your " "technical support representative."

SPA_T3E3-5-MSG_ENQUEUE_ERR

5-Notice

[chars]: Unable to enqueue message to T3E3 SPA process

The T3E3 SPA process message queue is full.

-

"Copy the error message exactly as it appears collect the output " "of 'show tech-support' command immediately and report it to your " "technical support representative."

SPA_T3E3-5-MSG_UNEXPECTED_ERR

5-Notice

[chars]: Unexpected SPA message [dec].

SPA has been removed but still there are outstanding events.

-

"If the CPU utilization is high try to reduce the CPU utilization"

SPA_T3E3-4-SUBRATE_FPGA_LOAD_FAILED

4-Warning

[chars] Programming [chars] subrate FPGA failed. The FPGA image is corrupted. One upgrade attempt is made.

The indicated subrate FPGA image is corrupted and programming of FPGA failed. One upgrade attempt will be made to recover from the failure.

-

"Automatically upgrade the subrate FPGA image uses default FPD " "Image Package. The package should match the running Cisco IOS " "release. This can be verified by the use of <CmdBold>show upgrade " "fpd package default<NoCmdBold> command. If subrate FPGA failure " "persists after upgrade SPA is disabled. Ensure the package file " "is intact."

SPA_T3E3-3-SUBRATE_FPGA_LOAD_FAILED2

3-Error

[chars] Programming [chars] subrate FPGA failed. The FPGA image is corrupted. FPD upgrade has been attempted. SPA is shut.

The indicated subrate FPGA image is corrupted even after FPD upgrade. The SPA is disabled until this problem is corrected.

spa-ser-t3e3

"Verify the correctness of the FPD Image Package. Note that the FPD " "Image Package used in the upgrade should match the running Cisco IOS " "release. This can be verified by the use of <CmdBold>show upgrade " "fpd package default<NoCmdBold> command."

SPA_EOWYN-3-ERROR

3-Error

Failed to create for [chars] : slot/bay:[dec]/[dec]

The 1Z 8S SPA/IM controller encountered an error.

asr900-tdm-combo

"Check the memory availabe in system and " LOG_STD_SH_TECH_ACTION

SPA_EOWYN-3-FATAL_ERROR

3-Error

Fatal error for [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller encountered a fatal error.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOWYN-3-INVALID_SPA_TYPE

3-Error

Invalid SPA type : slot/bay:[dec]/[dec] spa_type=[dec].

The channelized SPA type cannot be recognized by the version of Cisco IOS software currently running on the system.

asr900-tdm-combo

"Upgrade your system to a version of Cisco IOS software that supports " "this SPA type."

SPA_EOWYN-3-CREATE_FAIL

3-Error

Failed to create [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller descriptor block creation failed. Check the amount of available system memory.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOWYN-3-NULL_INSTANCE

3-Error

Null [chars] instance for slot/bay/port:[dec]/[dec]/[dec]

The instance pointer is NULL when getting data structure.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL.

asr900-tdm-combo

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-UNKNOWN_OPTION

3-Error

Received unknown [chars]: option=[dec]

Unknown option received.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-RETURN_ERROR

3-Error

Return error for [chars]: return_value=[dec]

Return error code received.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-6-XFP_OK

6-Information

[dec]/[dec]/[dec]: [chars] detected/inserted

XFP has been detected or inserted in a port in Channelized SPA.

asr900-tdm-combo

"This is a information message no action required"

SPA_EOWYN-3-NULL

3-Error

[chars]

The NULL pointer was detected when getting the data structure.

asr900-tdm-combo

SPA_EOWYN_ENABLE_DEBUG_ACTION

SPA_EOWYN-3-INTFC_FAILED

3-Error

Channel provisioning failed for [chars]

Channel could not be provisioned on SPA for this interface interface corresoponding to that channel has been moved to down state. If this interface was provisoned using the user interface then it may not appear in the interface list.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupted.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed.

asr900-tdm-combo

"Inform the network operator that subrate configuration was changed " "by remote end."

SPA_EOWYN-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOWYN-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing.

asr900-tdm-combo

"This is a internal software error. If this error happened while " "configuring FRR try reconfiguring the interface. If the error " "persists or occurred during normal operation decode the traceback " "and " LOG_STD_ACTION

SPA_EOWYN-3-NULL_VC_INST

3-Error

for[chars]

Pointer to VC INST is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOWYN-3-INVALID_MAX_VC

3-Error

for[chars]

invalid max vc for IM

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOWYN-3-NULL_OPTICS_HWIDB

3-Error

Optic HWIDB is NULL for [dec]/[dec]/[dec]

The optics hwidb for the port is Null.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-NULL_OPTICS_CDB

3-Error

Optic CDB is NULL for [dec]/[dec]/[dec]

The optics cdb for the port is Null.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-NULL_CDB

3-Error

payload CDB is NULL for [dec]/[dec]/[dec]

The payload cdb for the port is Null.

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-NULL_ETH_SUBBLOCK

3-Error

Ethernet subblock is null for [dec]/[dec]

The ethernet subblock is NULL

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-3-DCC_FAILURE

3-Error

Failed to retrieve DCC info for [dec]/[dec]/[dec]

\n The DCC info could not be retrieved

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_EOWYN-5-SPA_MODE_IS

5-Notice

spa_mode of [dec]/[dec] is [chars]

\n spa_mode is

asr900-tdm-combo

SPA_EOWYN_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-ERROR

3-Error

Failed to create for [chars] : slot/bay:[dec]/[dec]

The 1Z 8S SPA/IM controller encountered an error.

asr900-tdm-combo

"Check the memory availabe in system and " LOG_STD_SH_TECH_ACTION

SPA_ELBORON-3-FATAL_ERROR

3-Error

Fatal error for [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller encountered a fatal error.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_ELBORON-3-INVALID_SPA_TYPE

3-Error

Invalid SPA type : slot/bay:[dec]/[dec] spa_type=[dec].

The channelized SPA type cannot be recognized by the version of Cisco IOS software currently running on the system.

asr900-tdm-combo

"Upgrade your system to a version of Cisco IOS software that supports " "this SPA type."

SPA_ELBORON-3-CREATE_FAIL

3-Error

Failed to create [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller descriptor block creation failed. Check the amount of available system memory.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_ELBORON-3-NULL_INSTANCE

3-Error

Null [chars] instance for slot/bay/port:[dec]/[dec]/[dec]

The instance pointer is NULL when getting data structure.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL.

asr900-tdm-combo

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-UNKNOWN_OPTION

3-Error

Received unknown [chars]: option=[dec]

Unknown option received.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-RETURN_ERROR

3-Error

Return error for [chars]: return_value=[dec]

Return error code received.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-6-XFP_OK

6-Information

[dec]/[dec]/[dec]: [chars] detected/inserted

XFP has been detected or inserted in a port in Channelized SPA.

asr900-tdm-combo

"This is a information message no action required"

SPA_ELBORON-3-NULL

3-Error

[chars]

The NULL pointer was detected when getting the data structure.

asr900-tdm-combo

SPA_ELBORON_ENABLE_DEBUG_ACTION

SPA_ELBORON-3-INTFC_FAILED

3-Error

Channel provisioning failed for [chars]

Channel could not be provisioned on SPA for this interface interface corresoponding to that channel has been moved to down state. If this interface was provisoned using the user interface then it may not appear in the interface list.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupted.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed.

asr900-tdm-combo

"Inform the network operator that subrate configuration was changed " "by remote end."

SPA_ELBORON-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_ELBORON-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing.

asr900-tdm-combo

"This is a internal software error. If this error happened while " "configuring FRR try reconfiguring the interface. If the error " "persists or occurred during normal operation decode the traceback " "and " LOG_STD_ACTION

SPA_ELBORON-3-NULL_VC_INST

3-Error

for[chars]

Pointer to VC INST is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_ELBORON-3-INVALID_MAX_VC

3-Error

for[chars]

invalid max vc for IM

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_ELBORON-3-NULL_OPTICS_HWIDB

3-Error

Optic HWIDB is NULL for [dec]/[dec]/[dec]

The optics hwidb for the port is Null.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-NULL_OPTICS_CDB

3-Error

Optic CDB is NULL for [dec]/[dec]/[dec]

The optics cdb for the port is Null.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-NULL_CDB

3-Error

payload CDB is NULL for [dec]/[dec]/[dec]

The payload cdb for the port is Null.

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-NULL_ETH_SUBBLOCK

3-Error

Ethernet subblock is null for [dec]/[dec]

The ethernet subblock is NULL

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-3-DCC_FAILURE

3-Error

Failed to retrieve DCC info for [dec]/[dec]/[dec]

\n The DCC info could not be retrieved

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_ELBORON-5-SPA_MODE_IS

5-Notice

spa_mode of [dec]/[dec] is [chars]

\n spa_mode is

asr900-tdm-combo

SPA_ELBORON_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-ERROR

3-Error

Failed to create for [chars] : slot/bay:[dec]/[dec]

The SPA/IM controller encountered an error.

asr900-tdm-combo

"Check the memory availabe in system and " LOG_STD_SH_TECH_ACTION

SPA_EOMER-3-FATAL_ERROR

3-Error

Fatal error for [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller encountered a fatal error.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOMER-3-INVALID_SPA_TYPE

3-Error

Invalid SPA type : slot/bay:[dec]/[dec] spa_type=[dec].

The channelized SPA type cannot be recognized by the version of Cisco IOS software currently running on the system.

asr900-tdm-combo

"Upgrade your system to a version of Cisco IOS software that supports " "this SPA type."

SPA_EOMER-3-CREATE_FAIL

3-Error

Failed to create [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller descriptor block creation failed. Check the amount of available system memory.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOMER-3-NULL_INSTANCE

3-Error

Null [chars] instance for slot/bay/port:[dec]/[dec]/[dec]

The instance pointer is NULL when getting data structure.

asr900-tdm-combo

SPA_EOMERINTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-NULL_DATA_STRUCTURE

3-Error

[chars]

A software error occured and SPA driver is not able to retrieve the data structure mentioned in the message.

asr900-lotr-im

LOG_STD_ACTION

SPA_EOMER-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL.

asr900-tdm-combo

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-UNKNOWN_OPTION

3-Error

Received unknown [chars]: option=[dec]

Unknown option received.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-RETURN_ERROR

3-Error

Return error for [chars]: return_value=[dec]

Return error code received.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-NULL

3-Error

[chars]

The NULL pointer was detected when getting the data structure.

asr900-tdm-combo

SPA_EOMER_ENABLE_DEBUG_ACTION

SPA_EOMER-3-INTFC_FAILED

3-Error

Channel provisioning failed for [chars]

Channel could not be provisioned on SPA for this interface interface corresoponding to that channel has been moved to down state. If this interface was provisoned using the user interface then it may not appear in the interface list.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupted.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed.

asr900-tdm-combo

"Inform the network operator that subrate configuration was changed " "by remote end."

SPA_EOMER-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOMER-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing.

asr900-tdm-combo

"This is a internal software error. If this error happened while " "configuring FRR try reconfiguring the interface. If the error " "persists or occurred during normal operation decode the traceback " "and " LOG_STD_ACTION

SPA_EOMER-3-NULL_VC_INST

3-Error

for[chars]

Pointer to VC INST is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOMER-3-INVALID_MAX_VC

3-Error

for[chars]

invalid max vc for IM

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_EOMER-3-NULL_OPTICS_HWIDB

3-Error

Optic HWIDB is NULL for [dec]/[dec]/[dec]

The optics hwidb for the port is Null.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-NULL_OPTICS_CDB

3-Error

Optic CDB is NULL for [dec]/[dec]/[dec]

The optics cdb for the port is Null.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-NULL_CDB

3-Error

payload CDB is NULL for [dec]/[dec]/[dec]

The payload cdb for the port is Null.

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-NULL_ETH_SUBBLOCK

3-Error

Ethernet subblock is null for [dec]/[dec]

The ethernet subblock is NULL

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_EOMER-3-DCC_FAILURE

3-Error

Failed to retrieve DCC info for [dec]/[dec]/[dec]

\n The DCC info could not be retrieved

asr900-tdm-combo

SPA_EOMER_INTERNAL_SW_ERROR_ACTION

SPA_BILBO-3-NULL_DATA_STRUCTURE

3-Error

[chars]

A software error occured and SPA driver is not able to retrieve the data structure mentioned in the message.

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-UNSUPPORTED_DATA

3-Error

common_str_empty_str

A software error occured and SPA driver encounterd unsupported data mentioned in the message

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-TDL_SEND_FAIL

3-Error

common_str_empty_str

Failed to send TDL message.

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-MSG_ENQUEUE_ERROR

3-Error

[chars]

Failed to enqueue a message.

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-ID_INIT

3-Error

failed to initialize TDM IM ID table

Failed to initialize TDM IM ID table.

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-ID_ALLOC_ERR

3-Error

failed to allocate ID for TDM IM

Failed to allocate ID for TDM IM.

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-DPIDX_LKUP_ERR

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

asr900-lotr-im

LOG_STD_NO_ACTION

SPA_BILBO-3-VLAN_ID_NONZERO

3-Error

VLAN identifier is not zero before allocation for interface [chars]

The SPA driver is seeing non zero VLAN identifier before allocating new vlan identifier for the interface specified in the message. This indicates a software error.

asr900-lotr-im

LOG_STD_NO_ACTION

SPA_BILBO-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

The Periodic one second process creation failed. This indicates a software error.

asr900-lotr-im

LOG_STD_ACTION

SPA_BILBO-3-NULL_SPA_PTR

3-Error

-

The pointer to an SPA value is of a null value.

spa-bilbot3-ds3

LOG_STD_SH_TECH_ACTION

SPA_DENETHOR-3-NULL_DATA_STRUCTURE

3-Error

[chars]

A software error occured and SPA driver is not able to retrieve the data structure mentioned in the message.

asr900-lotr-im

LOG_STD_ACTION

SPA_DENETHOR-3-UNSUPPORTED_DATA

3-Error

common_str_empty_str

A software error occured and SPA driver encounterd unsupported data mentioned in the message

asr900-lotr-im

LOG_STD_ACTION

SPA_DENETHOR-3-TDL_SEND_FAIL

3-Error

common_str_empty_str

Failed to send TDL message.

asr900-lotr-im

LOG_STD_ACTION

SPA_DENETHOR-3-MSG_ENQUEUE_ERROR

3-Error

[chars]

Failed to enqueue a message.

asr900-lotr-im

LOG_STD_ACTION

SPA_DENETHOR-3-ID_INIT

3-Error

failed to initialize TDM IM ID table

Failed to initialize TDM IM ID table.

asr900-lotr-im

LOG_STD_ACTION

SPA_DENETHOR-3-ID_ALLOC_ERR

3-Error

failed to allocate ID for TDM IM

Failed to allocate ID for TDM IM.

asr900-lotr-im

LOG_STD_ACTION

SPA_DENETHOR-3-DPIDX_LKUP_ERR

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

asr900-lotr-im

LOG_STD_NO_ACTION

SPA_DENETHOR-3-VLAN_ID_NONZERO

3-Error

VLAN identifier is not zero before allocation for interface [chars]

The SPA driver is seeing non zero VLAN identifier before allocating new vlan identifier for the interface specified in the message. This indicates a software error.

asr900-lotr-im

LOG_STD_NO_ACTION

SPA_DENETHOR-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

The Periodic one second process creation failed. This indicates a software error.

asr900-lotr-im

LOG_STD_ACTION

SPA_LOTR-3-ERROR

3-Error

Failed to create for [chars] : slot/bay:[dec]/[dec]

The 1Z 8S SPA/IM controller encountered an error.

asr900-tdm-combo

"Check the memory availabe in system and " LOG_STD_SH_TECH_ACTION

SPA_LOTR-3-FATAL_ERROR

3-Error

Fatal error for [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller encountered a fatal error.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_LOTR-3-INVALID_SPA_TYPE

3-Error

Invalid SPA type : slot/bay:[dec]/[dec] spa_type=[dec].

The channelized SPA type cannot be recognized by the version of Cisco IOS software currently running on the system.

asr900-tdm-combo

"Upgrade your system to a version of Cisco IOS software that supports " "this SPA type."

SPA_LOTR-3-CREATE_FAIL

3-Error

Failed to create [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller descriptor block creation failed. Check the amount of available system memory.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_LOTR-3-NULL_INSTANCE

3-Error

Null [chars] instance for slot/bay/port:[dec]/[dec]/[dec]

The instance pointer is NULL when getting data structure.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL.

asr900-tdm-combo

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-UNKNOWN_OPTION

3-Error

Received unknown [chars]: option=[dec]

Unknown option received.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-RETURN_ERROR

3-Error

Return error for [chars]: return_value=[dec]

Return error code received.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-6-XFP_OK

6-Information

[dec]/[dec]/[dec]: [chars] detected/inserted

XFP has been detected or inserted in a port in Channelized SPA.

asr900-tdm-combo

"This is a information message no action required"

SPA_LOTR-3-NULL

3-Error

[chars]

The NULL pointer was detected when getting the data structure.

asr900-tdm-combo

SPA_LOTR_ENABLE_DEBUG_ACTION

SPA_LOTR-3-INTFC_FAILED

3-Error

Channel provisioning failed for [chars]

Channel could not be provisioned on SPA for this interface interface corresoponding to that channel has been moved to down state. If this interface was provisoned using the user interface then it may not appear in the interface list.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupted.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed.

asr900-tdm-combo

"Inform the network operator that subrate configuration was changed " "by remote end."

SPA_LOTR-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_LOTR-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing.

asr900-tdm-combo

"This is a internal software error. If this error happened while " "configuring FRR try reconfiguring the interface. If the error " "persists or occurred during normal operation decode the traceback " "and " LOG_STD_ACTION

SPA_LOTR-3-NULL_VC_INST

3-Error

for[chars]

Pointer to VC INST is NULL.

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_LOTR-3-INVALID_MAX_VC

3-Error

for[chars]

invalid max vc for IM

asr900-tdm-combo

LOG_STD_SH_TECH_ACTION

SPA_LOTR-3-NULL_OPTICS_HWIDB

3-Error

Optic HWIDB is NULL for [dec]/[dec]/[dec]

The optics hwidb for the port is Null.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-NULL_OPTICS_CDB

3-Error

Optic CDB is NULL for [dec]/[dec]/[dec]

The optics cdb for the port is Null.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-NULL_CDB

3-Error

payload CDB is NULL for [dec]/[dec]/[dec]

The payload cdb for the port is Null.

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-NULL_ETH_SUBBLOCK

3-Error

Ethernet subblock is null for [dec]/[dec]

The ethernet subblock is NULL

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-3-DCC_FAILURE

3-Error

Failed to retrieve DCC info for [dec]/[dec]/[dec]

\n The DCC info could not be retrieved

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_LOTR-5-SPA_MODE_IS

5-Notice

spa_mode of [dec]/[dec] is [chars]

\n spa_mode is

asr900-tdm-combo

SPA_LOTR_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-3-ERROR

3-Error

Failed to create for [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller encountered an error.

spa-choc3-ds0

"Check the memory availabe in system and " LOG_STD_SH_TECH_ACTION

SPA_CHOCX-3-FATAL_ERROR

3-Error

Fatal error for [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller encountered a fatal error.

spa-choc3-ds0

LOG_STD_SH_TECH_ACTION

SPA_CHOCX-3-INVALID_SPA_TYPE

3-Error

Invalid SPA type : slot/bay:[dec]/[dec] spa_type=[dec].

The channelized SPA type cannot be recognized by the version of Cisco IOS software currently running on the system.

spa-choc3-ds0

"Upgrade your system to a version of Cisco IOS software that supports " "this SPA type."

SPA_CHOCX-3-CREATE_FAIL

3-Error

Failed to create [chars] : slot/bay:[dec]/[dec]

The channelized SPA controller descriptor block creation failed. Check the amount of available system memory.

spa-choc3-ds0

LOG_STD_SH_TECH_ACTION

SPA_CHOCX-3-NULL_INSTANCE

3-Error

Null [chars] instance for [chars] : slot/bay:[dec]/[dec]

The instance pointer is NULL when getting data structure.

spa-choc3-ds0

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-3-UNKNOWN_OPTION

3-Error

Received unknown [chars]: option=[dec]

Unknown option received.

spa-choc3-ds0

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-3-RETURN_ERROR

3-Error

Return error for [chars]: return_value=[dec]

Return error code received.

spa-choc3-ds0

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-6-XFP_OK

6-Information

[dec]/[dec]/[dec]: [chars] detected/inserted

XFP has been detected or inserted in a port in Channelized SPA.

spa-choc3-ds0

"This is a information message no action required"

SPA_CHOCX-3-XFP_UNSUPPORTED

3-Error

[dec]/[dec]/[dec]: [chars] detected/inserted is not supported

Unsupported XFP has been detected or inserted in a port in Channelized SPA.

spa-choc3-ds0

"Remove the unsupported XFP/SFP and replace it with supported one."

SPA_CHOCX-6-XFP_REMOVED

6-Information

[dec]/[dec]/[dec]

XFP removed from a port in Channelized SPA

spa-choc3-ds0

"This is a information message no action required"

SPA_CHOCX-3-NULL

3-Error

[chars]

The NULL pointer was detected when getting the data structure.

spa-choc3-ds0

SPA_CHOCX_ENABLE_DEBUG_ACTION

SPA_CHOCX-6-SONET_ALARM

6-Information

[chars] [chars] [chars] [chars] [chars]

This message is generated whenever a sonet alarm is

-

LOG_STD_NO_ACTION

SPA_CHOCX-3-INTFC_FAILED

3-Error

Channel provisioning failed for [chars]

Channel could not be provisioned on SPA for this interface interface corresoponding to that channel has been moved to down state. If this interface was provisoned using the user interface then it may not appear in the interface list.

spa-choc3-ds0

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupted.

spa-choc3-ds0

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL.

spa-choc3-ds0

SPA_CHOCX_INTERNAL_SW_ERROR_ACTION

SPA_CHOCX-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed.

spa-choc3-ds0

"Inform the network operator that subrate configuration was changed " "by remote end."

SPA_CHOCX-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing.

spa-choc3-ds0

"This is a internal software error. If this error happened while " "configuring FRR try reconfiguring the interface. If the error " "persists or occurred during normal operation decode the traceback " "and " LOG_STD_ACTION

SPA_CHOCX-3-CHOCX_NAMESTRING_ERROR

3-Error

failed to get [chars] namestring

Error in retrieving namestring of a specified Controller/IDB

asr900-tdm-combo

"This is a internal software error. If the error persists or occurred " "during normal operation decode the traceback and " LOG_STD_ACTION

SPA_CHOCX-3-SONET_ALARM_PROC_ERR

3-Error

[chars] Error has occurred while processing in the sonet alarm-proc

Either free/create of the memory failed in SONET alarm proc

-

-

SPA_CHOCX-5-CEM_COUNT_WARNING

5-Notice

With Scaled CEM recommended value of LDP discovery timeout is 180 seconds before SSO. Current Scale: [dec]

User Recommendation

-

-

SPA_CHOCX_MCPRP-5-PATH_UPDOWN

5-Notice

Path [chars] changed state to [chars]

A Sonet high order path changed its state.

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "controller sonet<NoCmdBold>. Look into this " "output to see if there are any alarms being " "reported at the path level. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_MCPRP-5-T3_UPDOWN

5-Notice

T3 [chars] changed state to [chars]

A T3 within STS1 changed its state.

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "controller sonet<NoCmdBold>. Look into this " "output to see if there are any alarms being " "reported at the T3 level. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_MCPRP-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupt

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "running-config<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_MCPRP-1-ALLOCFAIL

1-Alert

OC3/STM1 [dec]/[dec] [chars] allocation failure

CHOCX controller or channel memory allocation failure

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> oir plugin<NoCmdBold> when the problem " "is happening. Check Bug Toolkit before calling the " "TAC. When calling the TAC please provide the above" "information along with output of <CmdBold>show " "logging<NoCmdBold> and the output of <CmdBold>show " "tech<NoCmdBold> details."

SPA_CHOCX_MCPRP-3-TIMEOUT

3-Error

Interface [chars]: [chars]

The CHOCX RP driver queries the LC for SONET information the LC didn't reply.

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> command<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with the " "output of <CmdBold>show logging<NoCmdBold> and the " "output of <CmdBold>show tech<NoCmdBold details."

SPA_CHOCX_MCPRP-3-PLUGIN_ERR

3-Error

[chars]

The RP plugin encountered an error during one of the Plugin calls

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> oir plugin<NoCmdBold> when the problem " "is happening. Check Bug Toolkit before calling the " "TAC. When calling the TAC please provide the above " "information along with the output of <CmdBold>show " "logging<NoCmdBold> and the output of <CmdBold>show " "tech<NoCmdBold> details."

SPA_CHOCX_MCPRP-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL

asr1k-spa-chstm1

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "running-config<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show running<NoCmdBold> " "and <CmdBold>show tech<NoCmdBold> details."

SPA_CHOCX_MCPRP-3-APS_CMD_FAIL

3-Error

Failed to send APS command [hec] to [chars] retcode [hec]

APS command sending failed

asr1k-spa-chstm1

"This is a internal software error. If this " "error happened while configuring APS try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION

SPA_CHOCX_MCPRP-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed

asr1k-spa-chstm1

"Inform the network operator that subrate " "configuration changed by remote end"

SPA_CHOCX_MCPRP-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing

asr1k-spa-chstm1

"This is a internal software error. If this " "error happened while configuring FRR try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION

SPA_LNM-5-ENABLED

5-Notice

Interface [chars] noise monitoring enabled for [chars]

Link Noise Monitoring has been enabled on the specified T1/E1 interface

-

"This is an information message to" "notify that Link Noise Monitoring has been enabled on the T1/E1 link." "No user action is required."

SPA_LNM-5-DISABLED

5-Notice

Interface [chars] noise monitoring disabled for [chars]

Link Noise Monitoring has been disabled on the specified T1/E1 interface

-

"This is an information message to" "notify that Link Noise Monitoring has been disabled on the T1/E1 link." "No user action is required."

SPA_LNM-3-MINWARNEXCEED

3-Error

Interface [chars] noise exceeded above minor warning threshold

Noise on the link has exceeded above the threshold value configured for minor warning level

-

"This link requires administrative attention"

SPA_LNM-3-MINWARNIMPROVE

3-Error

Interface [chars] noise improved below minor warning threshold

Noise on the link has improved and is below the threshold value configured for minor warning level

-

"No action required"

SPA_LNM-3-MAJWARNEXCEED

3-Error

Interface [chars] noise exceeded above major warning threshold

Noise on the link has exceeded above the threshold value configured for major warning level

-

"This link requires administrative attention"

SPA_LNM-3-MAJWARNIMPROVE

3-Error

Interface [chars] noise improved below major warning threshold

Noise on the link has improved and is below the threshold value configured for major warning level

-

"No action required"

SPA_LNM-2-REMOVE

2-Critical

Interface [chars] removed from bundle. Noise exceeded above remove threshold

Noise on the link has crossed the threshold value configured for link removal. This link is taken out of the MLP bundle. This is critical status for the link. This link is under monitoring state and will be added to the bundle again when the noise level is below the configured value.

-

"This link requires administrative attention"

SPA_LNM-2-RESTORE

2-Critical

Interface [chars] restored to bundle. Noise improved below removal threshold

Noise on the link has improved below the threshold value configured for link removal. This link is restored back to MLP bundle.

-

"No action required"

SPA_LNM-2-REMEXCEED

2-Critical

Interface [chars] noise exceeded above removal threshold

Noise on the link has exceeded above the threshold value configured for link removal

-

"This link requires administrative attention"

SPA_LNM-2-REMIMPROVE

2-Critical

Interface [chars] noise improved below removal threshold

Noise on the link has improved and is below the threshold value configured for link removal

-

"No Action required"

SPA_LNM-2-REMFAILED

2-Critical

Interface [chars] failed to remove link from bundle

Noise on the link has exceeded above the threshold value configured for link removal. However this link is not removed from the MLP bundle

-

"No Action required"

SPA_LNM-2-RESTOREFAILED

2-Critical

Interface [chars] failed to restore link to the bundle

Noise on the link has improved and is below the threshold value configured for link removal. However the link restore back to the MLP bundle failed

-

"No Action required"

SPA_LNM-2-REMEXCEEDLASTLINK

2-Critical

Interface [chars] Last link in bundle noise exceeded above removal threshold

Noise on the link has exceeded above the threshold value configured for link removal. However this link is the last link in the multilink bundle and it is not removed from the service.

-

"This link requires administrative attention"

SPA_LNM-3-GENEVENT

3-Error

[chars]

An Error has occured in the link noise monitoring

-

"Copy the error message exactly as it appears " "and report it to your technical support representative"

SPA_CHOCX_CWRP-5-PATH_UPDOWN

5-Notice

Path [chars] changed state to [chars]

A Sonet high order path changed its state.

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "controller sonet<NoCmdBold>. Look into this " "output to see if there are any alarms being " "reported at the path level. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_CWRP-5-T3_UPDOWN

5-Notice

T3 [chars] changed state to [chars]

A T3 within STS1 changed its state.

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "controller sonet<NoCmdBold>. Look into this " "output to see if there are any alarms being " "reported at the T3 level. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_CWRP-3-CORRUPT

3-Error

Corrupt configuration unsupported [chars] [dec] encountered

The OC3/STM1 RP driver running configuration is corrupt

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "running-config<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show tech<NoCmdBold> " "details"

SPA_CHOCX_CWRP-1-ALLOCFAIL

1-Alert

OC3/STM1 [dec]/[dec] [chars] allocation failure

CHOCX controller or channel memory allocation failure

c7600-sip-200

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> oir plugin<NoCmdBold> when the problem " "is happening. Check Bug Toolkit before calling the " "TAC. When calling the TAC please provide the above" "information along with output of <CmdBold>show " "logging<NoCmdBold> and the output of <CmdBold>show " "tech<NoCmdBold> details."

SPA_CHOCX_CWRP-3-TIMEOUT

3-Error

Interface [chars]: [chars]

The CHOCX RP driver queries the LC for SONET information the LC didn't reply.

c7600-sip-200

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> command<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with the " "output of <CmdBold>show logging<NoCmdBold> and the " "output of <CmdBold>show tech<NoCmdBold details."

SPA_CHOCX_CWRP-3-PLUGIN_ERR

3-Error

[chars]

The RP plugin encountered an error during one of the Plugin calls

c7600-sip-200

"This is a internal software error. Decode the " "traceback. Enable <CmdBold>debug hw-module subslot " "<slot>/<bay> oir plugin<NoCmdBold> when the problem " "is happening. Check Bug Toolkit before calling the " "TAC. When calling the TAC please provide the above " "information along with the output of <CmdBold>show " "logging<NoCmdBold> and the output of <CmdBold>show " "tech<NoCmdBold> details."

SPA_CHOCX_CWRP-3-NULL_SUBBLOCK

3-Error

Null ssb for [chars]

The hwidb subblock is NULL

c7600-sip-200

"This is a internal software error. Decode the " "traceback and get the output of <CmdBold>show " "running-config<NoCmdBold>. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of <CmdBold>show running<NoCmdBold> " "and <CmdBold>show tech<NoCmdBold> details."

SPA_CHOCX_CWRP-3-APS_CMD_FAIL

3-Error

Failed to send APS command [hec] to [chars] retcode [hec]

APS command sending failed

c7600-sip-200

"This is a internal software error. If this " "error happened while configuring APS try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION

SPA_CHOCX_CWRP-3-FRR_ERROR

3-Error

Error in handling FRR: [chars] [chars] [hec] [hec]

Error in FRR processing

c7600-sip-common

"This is a internal software error. If this " "error happened while configuring FRR try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION

SPA_CHOCX_CWRP-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed

c7600-sip-200

"Inform the network operator that subrate " "configuration changed by remote end"

SCC-3-XCVR_BAD_ID_HW

3-Error

Failed identification test in [dec]/[dec]/[dec].

The Transceiver in the specified port has failed authentication.

spa-infra

LOG_STD_ACTION

SPA_OBFL-3-APPLICATION

3-Error

SPA OBFL [chars] Application initialization failed for [chars]

The SPA could not initialize OBFL Application

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-PLATFORM_VECTOR

3-Error

SPA OBFL Platform Vector Function is NULL

The SPA doesnt have platform vector function

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-DEVICE_ENABLE

3-Error

[chars]: Failed to enable the SPA OBFL device

SPA OBFL failed to register the device with OBFL Infra

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-APP_CONTEXT

3-Error

SPA OBFL Application Context is NULL

The SPA Callback routine doesnt have valid OBFL Application context

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-APP_ENABLE

3-Error

[chars]: Failed to enable the [chars] application with OBFL INFRA

SPA Failed to register the application with OBFL INFRA

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-DEVICE_DISABLE

3-Error

[chars]: Failed to disable the SPA OBFL Device

Failed to disable the SPA OBFL device during OIR

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-SPA_OBFL_INFO

3-Error

[chars]: Failed to get the SPA OBFL [chars] info

Failed to get the SPA OBFL info structure

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-MALLOC_FAILED

3-Error

[chars]: Failed to allocate memory for [chars]

Failed to allocate memeory for the SPA OBFL feature

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-ERRMSG_REG

3-Error

[chars]: Failed to register Errmsg Facility

Failed to register the SPA OBFL errmsg facility with OBFL Infra

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-ENV_UDI

3-Error

[chars]: SPA OBFL Enviornment UDI structure is NULL

OBFL Enviornment UDI structure is NULL for the SPA

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-ENV_ENQUEUE

3-Error

[chars]: Failed to enqueue the Enviornment event

SPA OBFL Failed to enqueue the enviornment event to OBFL Infra.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-OBFL_DEVINFO

3-Error

SPA OBFL Devinfo is NULL

The SPA Callback routine doesnt have valid OBFL Devinfo

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-SIZE_TOOBIG

3-Error

Size + Offset is beyond EEPROM boundary. Offset 0x[hec] size 0x[hec]

The SPA Callback routine doesnt have valid EEPROM read/write bytes

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-SPA_NOTFOUND

3-Error

SPA Plugin failed slot [dec] bay [dec]

Getting the SPA Plugin structure is failed.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-BAY_FAILED

3-Error

[chars]: Failed to get the bay slot [dec] bay [dec]

Getting the SPA structure is failed for the slot/bay combination.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-ENV_FVT_FAILED

3-Error

[chars]: Enviornment Function Vector table is empty for [chars] monitoring

Failed to get the enviornment vector table for the SPA

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-VOLT_LIMIT_TABLE_FAILED

3-Error

[chars]: Failed to get the voltage limit table

Failed to get voltage limit table for the SPA

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-READ_SENSOR_FAILED

3-Error

[chars]: Failed to read the [chars] from sensor [dec]

Failed to read the enviornment sensors

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-EEPROM_FAILED

3-Error

[chars]: Failed to read the [chars] from EEPROM

Failed to read the particular details from SPA IDPROM.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-DEV_ADDR

3-Error

[chars]: SPA Blackbox EEPROM base address is NULL

SPA specific code returned NULL for Blackbox EEPROM base address

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-READ_FAILED

3-Error

[chars]: Failed to read the Blackbox EEPROM Address 0x[hec] offset 0x[hec] size 0x[hec]

Reading the Blackbox EEPROM failed.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-WRITE_FAILED

3-Error

[chars]: Failed to write the Blackbox EEPROM Address 0x[hec] offset 0x[hec] size 0x[hec]

Writing to Blackbox EEPROM failed.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-ERASE_FAILED

3-Error

[chars]: Failed to erase the Blackbox EEPROM Address 0x[hec] offset 0x[hec] size 0x[hec]

Erasing the Blackbox EEPROM failed.

spa-obfl

LOG_STD_ACTION

SPA_OBFL-3-RESET_REASON_FAIL

3-Error

[chars]: Failed to get the SPA reset reason from RP due to IPC [chars].

SPA OBFL failed to get the SPA reset reason from RP.

spa-obfl

LOG_STD_ACTION

SPACP-3-CREATE

3-Error

[chars]: SPA Bus Device creation failed.

Can not allocate memory for SPA Bus structure.

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPACP-3-INIT

3-Error

[chars]: Failed to initialize SPACP. [chars].

SPACP messaging could not be initialized because of the reason specific in the message text.

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPACP-3-BUFFER

3-Error

[chars]: Failed to allocate buffer for SPACP message.

Can not allocate memory for SPACP message.

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPACP-3-SEND

3-Error

[chars]: Failed to send SPACP message.

Failed to send a message to the SPA.

spa-ipsec-2g

LOG_STD_RECUR_ACTION

SPACP-3-OPCODE

3-Error

[chars]: SPACP opcode 0x%04x unknown.

A failure occurred when sending a command to the SPA indicated in the error message.

spa-ipsec-2g

SPA_CEMA_FAIL_ACTION

CEMA-3-CEMA_ADD_FAIL

3-Error

[chars]: CEMA SB addition failed for interface [chars]

A failure occurred when adding cema_sb to the interface shown in the error message.

-

SPA_CEMA_FAIL_ACTION

CEMA-3-CLEAR_CONNECTION_STATS_FAIL

3-Error

[chars]: clear connection stats failed [chars]

A failure occurred when sending a clear connection stats command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-CONNECTION_DELETE_FAIL

3-Error

[chars]: connection delete failed [chars]

A failure occurred when sending a connection delete command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-ATM_VP_CONFIG_FAIL

3-Error

[chars]: connection configuration failed for VP [dec] [chars]

A failure occurred when sending a VP configuration command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-ATM_VC_CONFIG_FAIL

3-Error

[chars]: connection configuration failed for VC [dec]/[dec] [chars]

A failure occurred when sending a VC configuration command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-CLEAR_INTERFACE_STATS_FAIL

3-Error

[chars]: clear interface stats failed [chars]

A failure occurred when sending a clear interface stats command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-INTERFACE_DELETE_FAIL

3-Error

[chars]: interface delete failed [chars]

A failure occurred when sending an interface delete command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-INTERFACE_CONFIG_FAIL

3-Error

[chars]: interface configuration failed [chars]

A failure occurred when sending an interface delete command.

-

CEMA_CMD_FAIL_ACTION

CEMA-3-CARD_TYPE_CONFIG_FAIL

3-Error

[chars]: card type configuration failed [chars]

A failure occurred when sending a card type configuration command.

-

CEMA_CMD_FAIL_ACTION

PROTECTION-3-NULL_DATA_STRUCTURE

3-Error

[chars]

A software error occured and driver is not able to retrieve the data structure mentioned in the message.

asr900-lotr-im

LOG_STD_ACTION

PROTECTION-3-DISPATCH_INIT_TDLH_FAILURE

3-Error

Failed to initialize dispatch path for APSd slot[dec]

Failed to initialize dispatch path handle for APSd communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-SETUP_TDLH_FAILURE

3-Error

Failed to set the alloc/free handler for APSd [dec] handle

Failed to set the alloc/free handler for APSd communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-CREATE_TDLH_FAILURE

3-Error

Failed to create APSd [dec] handle

Failed to create message handle for APSd communication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-DOMAIN_TDLH_FAILURE

3-Error

[chars] rc = [dec]

Failed to bind message handle for APSdcommunication.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-SEND_FAIL

3-Error

group%llu type[dec] msg[chars] errcode[dec]

Failed to send message to APSd.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-SEND_FAIL_SHUT

3-Error

slot[dec] bay[dec] port[dec] vt[dec] sts[dec] type[dec] msg[chars] errcode[dec]

Failed to send shut message to APSd.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-RESP_FAIL

3-Error

msg[chars] retval0x[hec]

Failure response from APSd.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-3-NULL_PTR

3-Error

[chars]

Failed to initialize.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

PROTECTION-4-SEMAHOG

4-Warning

Process [dec] [chars] hogging [chars]! calling proc [dec] [chars]

-

-

-

PROTECTION-3-PPG_HWID

3-Error

group[dec] bay[dec] port[dec] prot_type[dec] msg[chars]

ppg hwid

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

SPA_CT3-3-INVALID_SPA_TYPE

3-Error

Invalid SPA type : slot/bay:[dec]/[dec] spa_type=[dec].

The Channelized T3 SPA type cannot be recognized by the version of Cisco IOS software currently running on the system.

spa-ct3-ds0

"Upgrade your system to the latest version of Cisco " "IOS software in your release train. If you require " "further assistance " LOG_STD_SH_TECH_ACTION

SPA_CT3-3-PROCESS_FAIL

3-Error

process creation failed for [chars]

A command could not be processed because of a process creation failure.

spa-ct3-ds0

LOG_STD_ACTION

SPA_CT3-3-SUBRATE_FPGA_DL_FAILED

3-Error

[chars]: Failed to download the subrate FPGA image.

The indicated SPA was not able to download the subrate FPGA image during card initialization sequence. The image might be corrupted and the system will try to recover from this error by upgrading the image.

spa-ct3-ds0

"If the system cannot recover from this error automatically after a few " "attempts it will power-off the affected SPA. In this case copy the " "error message exactly as it appears and gather the output of the " "<CmdBold>show hw-module subslot<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg>" " <CmdBold>fpd<NoCmdBold> and <CmdBold>show hw-module subslot<NoCmdBold> " "<CmdArg>slot/subslot<NoCmdArg> <CmdBold>oir<NoCmdBold> commands then " "contact your technical support representative with the gathered " "information."

SPA_CT3-5-DEF_SUBRATE

5-Notice

[chars] [chars]

Remote subrate configuration changed

spa-ct3-ds0

"Inform the network operator that subrate " "configuration changed by remote end"

SPA_NAM-3-NAM_SW_ERR

3-Error

NULL

The SPA driver detected a software error condition on the SPA card. This might result in improper operation.

spa-nam

"The SPA driver has encountered a software error." "Please power down and reseat the indicated SPA card. " "Copy the error message exactly as it appears and " "open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical support representative and provide " "the representative with the information you have gathered. Be sure to " "attach to your case the output of the <CmdBold>show logging<NoCmdBold> " "<CmdBold>show monitor event-log spa all<NoCmdBold> and " "<CmdBold>show tech-support<NoCmdBold> commands your troubleshooting " "logs and the specific error message."

QUICC_SERIAL-1-INITFAIL

1-Alert

msgtxt_initfail

The serial interface controller of the QUICC chip could not be\n\ initialized or started for operation. There is probably a hardware\n\ problem.

-

"Power cycle the system. If the error reoccurs replace the unit."

QUICC_SERIAL-3-UNDERFLO

3-Error

Unit [dec] underflow error

While transmitting a frame the serial controller chip's local buffer\n\ received insufficient data because data could not be transferred to the\n\ chip fast enough to keep pace with its output rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required.\n\\n\ If the problem reccurs it indicates a hardware error that might be\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative."

QUICC_SERIAL-3-CTSLOST

3-Error

Unit [dec] Clear to Send Lost

-

-

"Check the serial interface cable and or communication equipment such\n\ as the channel service unit/data service unit CSU/DSU."

QUICC_SERIAL-5-LINEFLAP

5-Notice

Unit [dec] excessive modem control changes

-

-

"Check the serial interface cable. The error can occur if the cable is\n\ disconnected or has come loose and is picking up noise. If the cable\n\ appears to be connected correctly check the equipment connected to the\n\ cable."

QUICC_SERIAL-5-LOSTCARR

5-Notice

Unit [dec] carrier detect signal lost during message reception

-

-

"Check the serial interface cable. The error can occur if the cable is\n\ disconnected."

QUICC_ASYNC-3-CTSLOST

3-Error

Unit [dec] Clear to Send Lost

-

-

"Check the serial interface cable and/or communication equipment such\n\ as the channel service unit/data service unit CSU/DSU."

ALIGN-3-SPURIOUS

3-Error

Spurious memory access made at [chars] reading 0x[hec]

An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked.

-

"Copy the error message exactly as it appears on the console or in the " "system log. Issue the <CmdBold>show alignment<noCmdBold> command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the <CmdBold>show alignment<noCmdBold> output call your " "Cisco technical support representative and provide the representative " "with the gathered information."

ALIGN-3-TRACE

3-Error

-Traceback= [chars]

A trace that shows where the previous ALIGN error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

QUICC-3-UCODE_REV_UNKN

3-Error

Unknown microcode revision number: [dec]

The MC68360/QUICC CPU was running an unexpected version of microcode.\n\ This could be possible if a new version of the QUICC chip was released\n\ or if a very old version was used in the manufacturing process. This\n\ could also occur if a new version of microcode was released to fix\n\ any bugs

-

"A decrease in performance might occur for any async interfaces running\n\ PPP. Call your technical support representative if this is an \n\ issue."

QUICC-1-NOMEMORY

1-Alert

msgtxt_nomemory

The MC68360/QUICC CPU was unable to access the memory it needs to\n\ carry out its functions. Here are some possible causes.\n\\n\ The network is large requiring a lot of memory for routing tables and\n\ so on.\n\\n\ The router configuration has many features enabled each of which\n\ require a certain amount of memory.\n\\n\ A software error memory leak exists.

-

"Reduce system activity to ease the memory demand or upgrade to a\n\ larger memory configuration."

QUICC-3-OWNERR

3-Error

msgtxt_ownerror

An internal software error occurred.

-

"Call your technical support representative to obtain a software\n\ upgrade."

QUICC_ETHER-1-INITFAIL

1-Alert

msgtxt_initfail

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

QUICC_ETHER-5-COLL

5-Notice

Unit [dec] excessive collisions. Retry limit [dec] exceeded

An Ethernet cable is broken or unterminated.

-

"Check cables for proper connections termination and so on."

QUICC_ETHER-3-UNDERFLO

3-Error

Unit [dec] underflow error

While transmitting a frame the Ethernet controller chip's local buffer received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally such a problem is temporary depending on transient peak loads within the system.

-

"The system should recover. No action is required. If the problem recurs it indicates a hardware error that might be related to data traffic patterns. Copy the error message exactly as it appears and report it to your technical support representative."

QUICC_ETHER-1-LOSTCARR

1-Alert

Unit [dec] lost carrier. Transceiver problem?

The Ethernet 10BaseT cable is unplugged.

-

"Connect the 10BaseT Ethernet cable."

QUICC_ETHER-5-LATECOLL

5-Notice

Unit [dec] late collision error

The Ethernet cable might be too long or there could be too many repeaters such that the delay from one end to the other is too long. The Ethernet cable might be overloaded with too many users.

-

"Verify that your Ethernet cable is the correct length and that you do not have too many repeaters in use. If these are not the problem try removing hosts from the Ethernet segment to reduce the load."

QUICC_ETHER-5-HBEAT

5-Notice

Unit [dec] heartbeat check failure

The Ethernet cable might be too long or there could be too many repeaters such that the delay from one end to the other is too long. The Ethernet cable might be overloaded with too many users.

-

"Verify that your Ethernet cable is the correct length and that you do not have too many repeaters in use. If these are not the problem try removing hosts from the Ethernet segment to reduce the load."

ETHERNET-1-NOMEMORY

1-Alert

msgtxt_nomemory

Insufficient memory exists to allocate the necessary memory pools.

-

"If this message recurs call your technical support representative for assistance."

ETHERNET-1-TXERR

1-Alert

[chars]: Fatal transmit error. Restarting...

A fatal transmit error occurred on the Ethernet line causing the line to be restarted.

-

"If this message recurs call your technical support representative for assistance."

ETHERNET-4-UNSUPINTFC

4-Warning

Interface Ethernet[dec] not supported by [chars] image

The specific ethernet interface is not supported by the operating system currently running.

-

"If the hardware configuration is supported by a newer version of the operating system it will be necessary to upgrade the software in order to support this interface."

CERF-3-RECOVER

3-Error

[chars]

This message is emitted when there has been a full recovery after a\n\ cache error

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

CERF-2-ABORT

2-Critical

[chars]

This message is emitted when a cache error has occured but an attempt\n\ to recover has been aborted

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

GT64010-3-DMA

3-Error

Interrupt error c=[hex] m=[hex] rc=[hex]

An unexpected interrupt was registered from a DMA \n\ engine that was not initialized by software.

-

LOG_STD_ACTION

GT64010-3-TIMER

3-Error

Interrupt error c=[hex] m=[hex] rc=[hex]

An unexpected timer interrupt was received from\n\ a timer element that was not initialized by software.

-

LOG_STD_ACTION

GT64010-3-NOCHANNEL

3-Error

Referencing unused DMA channel [dec]

An access to an uninitialized DMA engine was attempted.

-

LOG_STD_ACTION

GT64010-1-DMASTALL

1-Alert

DMA interrupt stalled restarted engine [dec]

The driver timed out waiting for completion of DMA task. \n\ The DMA engine has been restarted.

-

LOG_STD_RECUR_ACTION

GT64010-3-TIMERINSTALL

3-Error

Attempt to install already installed timer [dec]

An attempt was made to initialize a timer element that\n\ is already in use.

-

LOG_STD_ACTION

R4K_MP-3-CRASHED

3-Error

CPU [dec] has now crashed a total of [dec] times.

The indicated CPU crashed and has been restarted.

msw

LOG_STD_ACTION

R4K_MP-5-DELEGATE_GETBUF

5-Notice

Delegated call to 0x[hec] failed out of buffers

An RPC call to the indicated function failed.

msw

LOG_STD_ACTION

UBR10K_REDUNDANCY-4-MSGVERSION

4-Warning

Incompatible message version with slot [dec]

There is incompatibility between the the message version being sent by the line card and the message version used by the RP. This type of incompatibility could happen if the RP and Schooner line card are using different IOS versions due to an RP oir event

ubr10k-pre-redundancy

"A microcode reload will solve the problem. "

UBR10K_REDUNDANCY-3-CHKPT_INTERNAL

3-Error

Internal PRE checkpointing error [[chars]]

An internal error occurred within the PRE checkpointing code

ubr10k-pre-redundancy

LOG_STD_ACTION

UBR10K_REDUNDANCY-4-RP_HA_STDBY_INCONSISTENT

4-Warning

Standby PRE dropping inconsistent sync messages [chars] [chars].

An inconsistency was detected within the PRE config/data sync code. This can occur under normal situations if a cable linecard is reset while the standby PRE is still coming up. Further debugging can be turned on to dump contents of inconsistency sync packets

ubr10k-pre-redundancy

LOG_STD_ACTION

UBR10K_REDUNDANCY-3-CREATEFAIL

3-Error

UBB10K HA Entity CF rcv process create failed

Failed to create the ubr10k HA entity checkpoint receive process

ubr10k-pre-redundancy

LOG_STD_ACTION

CR10K_DIAG-5-PXFOVERSUB

5-Notice

PXF utilization is [dec]%% system is close to be overloaded.

The health monitoring code has detected the system is close to be oversubscribed.

platform-cmts

LOG_STD_ACTION

CR10K_DIAG-3-LLQDROP

3-Error

LLQ Drops on [chars] new_drops:[dec] total_drops:[dec]

The health monitoring code has detected drops on the low latency queue of the specified interface. This is not expected behavior. The interface should be monitored to determine if drops continue to increase.

platform-cmts

LOG_STD_ACTION

CR10K_DIAG-3-MEMLEAK

3-Error

MemLeak Monitor: [chars] [chars]

The health monitoring code has detected potential memory leaks by the local IOS sub-system. This is not an expected behavior. The sub-system should be monitored to detect if real memory leaks continue to happen.

platform-cmts

LOG_STD_ACTION

CR10K_DIAG-5-RU_OLDBUFF_HOLD

5-Notice

IO-Buff-Hoard Monitor: [chars]

The health monitoring code has detected potential memory leaks by the local IOS sub-system. This is not an expected behavior. The sub-system should be monitored to detect if real memory leaks continue to happen.

platform-cmts

LOG_STD_ACTION

CR10K_DIAG-5- DIAG_LOOP_MG

5-Notice

US PHY [dec] loopback failure [chars] [dec]

Failed to loopback frame from CPU -> PHY -> JIB3 US -> CPU

ubr10k-sw

"Monitor failed LC for excessive failures."

CR10K_DIAG-5- DIAG_LOOP_RXERR

5-Notice

US PHY [dec] loopback discrepency detected frames tx [dec] rx [dec] err [hec]

Failed to loopback one or more frames

ubr10k-sw

"Monitor failed LC for excessive failures."

CR10K_DIAG-5- DIAG_LOOP_SEQ

5-Notice

US PHY [dec] loopback failed unexpected seq [dec] exp [dec]

Failed to loopback one or more frames

ubr10k-sw

"Monitor failed LC for excessive failures."

CR10K_DIAG-5- DIAG_LOOP_ETSEC

5-Notice

eTSEC loopback failure [chars]

A loopback between eTSEC1 and eTSEC2 failed.

ubr10k-sw

"Monitor failed LC for excessive failures."

LCLOG-3-INVDEV

3-Error

Invalid slot/subslot number in logger API callback LC=[dec]/[dec]

The line card crash info subsystem on the PRE was called from the BPE subsystem with an invalid slot/subslot. This indicates a software defect in the system.

ubr10k-sw

"Report this defect with as much information about the subsystem as " "possible. There is no adverse effect to the PRE -- it ignores the " "bad callback and continues. If the problem is recurring " "rebooting the router is recommended."

LCLOG-3-INVSTATE

3-Error

LC logger in bad state LC=[dec]/[dec]state=[chars]msg=[chars]

-

-

-

LCLOG-3-MSGGIANT

3-Error

LC log msg larger than max allowed LC=[dec]/[dec]length=[dec]

-

-

-

LCLOG-3-MSGTOOBIG

3-Error

LC log msg longer than expected LC=[dec]/[dec]len=[dec]exp=[dec]

The PRE part of the line card logger server has received more text for a message than the start message indicated. This is probably due to a software defect.

ubr10k-sw

"Report this defect with as much information about the line card " "logger subsystem possible."

LCLOG-3-OVERFLOW

3-Error

LC log msg longer than msg buffer LC=[dec]/[dec]len=[dec]max=[dec]

The PRE part of the line card logger server has received more text for a message than will fit in the message log buffer. This is probably due to a software defect.

ubr10k-sw

"Report this defect with as much information about the line card " "logger subsystem possible."

UBRLCCOREDUMP-3-BADCLOSE

3-Error

Can't close slave core socket for slot [dec]/[dec]

The system just finished dumping a core file from a line card. It tried to close this file on the remote system and failed.

ubr10k-sw

"Debug network connections and user priviledges."

UBRLCCOREDUMP-3-BADOPEN

3-Error

Can't open slave core socket for slot [dec]/[dec]

The system wants to dump a core file to a remote sytem but it is unable to open the remote file

ubr10k-sw

"Check to make sure the remote system is accessable and the " "protocol is set up correctly."

UBRLCCOREDUMP-3-BADWRITE

3-Error

Can't write [chars] to slave core socket for slot [dec]/[dec]

The system is trying to write a core dump file to a remote sytem. The file was opened and an error occurred during a write to the file

ubr10k-sw

"Check network and disk space available."

UBRLCCOREDUMP-3-REFUSAL

3-Error

Refusing [chars] dump for card [dec]/[dec].

The PRE/NPE card has refused this dump because CLI is not configured for it or file access voilation on the tftp server.

ubr10k-sw

"Check exception-slave CLI on NPE"

UBRLCCOREDUMP-3-NOQUEUE

3-Error

Cannot create queue to receive dump packets for slot [dec]/[dec]

The system is trying to write a core dump file to a remote sytem. It could not create a queue to hold dump data coming from the line cards.

ubr10k-sw

"Add memory."

UBRLCCOREDUMP-3-NOMSG

3-Error

No message on queue

A core dump message from a line card that the should not be dumping core arrived at the PRE.

ubr10k-sw

"Gather information about the state of linecards and file a bug."

UBRLCCOREDUMP-3-ILLMSG

3-Error

Coredump message received from slot [dec]/[dec] not in dump state\n

-

-

-

UBRLCCOREDUMP-4-TIMEOUT

4-Warning

[chars] major [dec] minor [dec]

The system is trying to write a core dump file but the PRE timed out waiting for data from the line card.

ubr10k-sw

"Gather information about the line card and file a bug."

UBRLCCOREDUMP-3-NOPROC

3-Error

Unable to create data handler process

The system wants to write a core dump file to a remote system but it is unable to start a process to dump the file.

ubr10k-sw

"Gather information about the number of processes running and " "amount of memory in the system and file a bug."

UBRLCCOREDUMP-3-ILLNVGEN

3-Error

Illegal call to cr10k_rp_lc_cfg_coredump_nvgen

The NVGEN routine was called but nvgen was not set.

ubr10k-sw

"Gather information about the processes running on this platform " "and the traceback and file a bug."

UBRLCCOREDUMP-3-ILLTD

3-Error

Testdump only valid on line cards not allowed on PREs\n

You cannot run a line card coredump test for an PRE.

ubr10k-sw

"Do not do this."

UBRLCCOREDUMP-6-LERP

6-Information

Cannot configure linecard exceptions for [chars] PRE

The exception linecard commands can only be used to configure exceptions on a line card. PRE are not allowed.

ubr10k-sw

"Use the exception command without linecard to configure PRE core dumps."

UBRLCCOREDUMP-2-EOM

2-Critical

Cannot allocation memory for [chars]\n

The system cannot allocate memory for the coredump subsystem.

ubr10k-sw

"Add more memory."

UBRLCCOREDUMP-3-TOOLONGFILENAME

3-Error

Filename for coredump file is too long for slot [dec]/[dec]

Filename is too long for core dump file

ubr10k-sw

"Reduce the length of coredump filename string via CLI"

UBRLCCOREDUMP-3-BADSLOTNUMBER

3-Error

Refusing dump because card slot number is out of bounds for card [dec]/[dec].

The NPE/PRE card has refused this dump because slot number is out of bounds.

ubr10k-sw

"Check IPC debug message for malformed packet"

RPLIC-3-ACTIVATE

3-Error

Could not activate [chars] rc [dec] [chars]

The RP license module activation failed

APPLICATION

LOG_STD_DDTS_TAC_DETAILS

RPLIC-3-REGISTER

3-Error

Could not register [chars] rc [dec] [chars]

The RP license feature register failed

APPLICATION

LOG_STD_DDTS_TAC_DETAILS

RPLIC-3-REQUEST

3-Error

Failed to request license feature [chars] units [dec] rc [dec] [chars]

The RP license feature request failed

APPLICATION

LOG_STD_DDTS_TAC_DETAILS

RPLIC-3-RELEASE

3-Error

Failed to release license handle 0x[hec] units [dec] rc [dec] [chars]

The RP license feature release failed

APPLICATION

LOG_STD_DDTS_TAC_DETAILS

RPLIC-3-STORAGE

3-Error

License storage error [chars]

The RP license storage status is BAD

APPLICATION

"Check the RP license details. If the problem is not" " fixed by multiple reinstall attempts board RMA" " may be required"

RPLIC-1-REGISTER_STORAGE

1-Alert

Register license storage [chars] failed rc [dec] [chars]

The RP license storage register failed

APPLICATION

"Check the RP license details" " If the problem is not fixed by multiple reinstall" " attempts board RMA may be required"

RPLIC-1-REGPERMSTORFAIL

1-Alert

Register license permanent storage [chars] failed rc [dec] [chars]

The RP license storage register failed

APPLICATION

"Check the RP license details" " If the problem is not fixed by multiple reinstall" " attempts board RMA may be required"

RPLIC-6-SHUT

6-Information

Can't noshut [chars] due to insufficient licenses

Unable to no shut the TenGigaE due to insufficient licenses

APPLICATION

"Check number of licenses installed"

RPLIC-6-NOSHUT

6-Information

[chars] has been no shut

License no shutdown TenGigaE

APPLICATION

"None"

RPLIC-6-LICGRANT

6-Information

No license was granted for [chars]

License wasn't granted for this TenGigaE

APPLICATION

"None"

RPLIC-3-NULLHWIDB

3-Error

Can't get hwidb of slot [dec] port [dec]

Failed to get hwidb of BH ethernet

APPLICATION

LOG_STD_DDTS_TAC_DETAILS

HDSPA_LIC-6-OUT_OF_RANGE

6-Information

SPA [dec]/[dec] [chars] is already [dec]

License counters have reached boundary condition

APPLICATION

"Internal Error check license and report to TAC"

HDSPA_LIC-5-EXCESS_LIC

5-Notice

Installed license count[dec] exceeds hardware capability[dec]

Some licenses are wasted currently

APPLICATION

"If this is caused by intentional action or RMA " "please transfer excess SPA_DS_License licenses to " "another PRE otherwise please call TAC"

HDSPA_LIC-3-CSB_FAIL

3-Error

[chars] failed for [chars]

An attempt to parse a license related CLI failed

APPLICATION

"Check the HDSPA license details and call TAC"

HDSPA_LIC-6-SHUT

6-Information

[chars] channel [dec] has been shutdown due to insufficient licenses

Unable to no shut the Channel due to insufficient licenses

APPLICATION

"Check number of licenses installed"

HDSPA_LIC-6-NOSHUT

6-Information

[chars] channel [dec] has been restored to no shut

Restored previously shutdown channels to no shut state

APPLICATION

"None"

HDSPA_LIC-6-NOSHUTFAIL

6-Information

[chars] channel [dec] no shut is not allowed due to insufficient licenses

Unable to no shut the channel due to insufficient licenses

APPLICATION

"Check number of licenses installed"

HDSPA_LIC-5-EXCEED_HW_CAP

5-Notice

DS_License installed[dec] on a single HDSPA exceeds

Some of the licenses are wasted.

APPLICATION

"This could happen after license rehost. " "Please transfer the excess licenses to another PRE."

HDSPA_LIC-3-BOOLTIMEOUT

3-Error

Fail to wait for boolean [chars]

This boolean is not set true before timeout

APPLICATION

"This boolean is not set true before timeout" "Please check the process that set this boolean"

HDSPA_LIC-3-FLASHERROR

3-Error

[chars]

Unexpected flash error happend

APPLICATION

"Check SPA license flash"

CMTS_LIC-3-NULL_HWIDB

3-Error

Function [chars] invoked with hwidb NULL

hwidb passed to function is NULL

PLATFORM

"Internal Error check license and report to TAC"

CMTS_LIC-3-NULL_LICENSE_INFO

3-Error

Line Card [dec]/[dec] license info is NULL!

The Line card license info is NULL

PLATFORM

"Check the line card license details"

CMTS_LIC-1-BAD_LICENSE_STORAGE

1-Alert

License Storage Error on Linecard [dec]/[dec]

The Line card license storage status is BAD

PLATFORM

"Check the line card license details" " If the problem is not fixed by multiple reinstall attempts" " board RMA may be required"

CMTS_LIC-3-LICENSE_ACTIVFAIL

3-Error

Could not activate license module on Linecard [dec]/[dec]

The Line card license module activation failed

ubr10000

LOG_STD_DDTS_TAC_DETAILS

CMTS_LIC-3-INVALID_LIC_INFO

3-Error

License Info Buffer is empty for [dec]/[dec]

The license info buffer received/created from CLC is empty

PLATFORM

"Check the line card license details at CLC"

CMTS_LIC-3-LIC_LED_ERROR

3-Error

Unable to set Downstream Density LED

Unable to set Downstream Density LED

PLATFORM

"Try OIR the CLC and check the LED"

CMTS_LIC-3-LIC_WDC_ALLOCATION_ERROR

3-Error

Unable to allocate memory for WDC memory storage

Unable to allocate memory for WDC memory

PLATFORM

"Try the command again at a later time"

CMTS_LIC-3-CSB_FAIL

3-Error

[chars] failed for [chars]

An attempt to parse a license related CLI failed

PLATFORM

"Check the linecard license details and call TAC"

CMTS_LIC-6-LICENSE_ENFORCE

6-Information

Linecard [dec]/[dec] set to mode [chars]

License Information has been applied

PLATFORM

"No action required"

CMTS_LIC-3-LICENSE_SEATNAME_ERROR

3-Error

Unable to get slotid from [chars]

Unable to get slotid

PLATFORM

"No action required"

CMTS_LIC-3-APPLY_DS_FAILED

3-Error

Applying downstream license failed

Unable to apply the downstream license

ubr10000

"Internal Error check license and report to TAC"

CMTS_LIC-3-APPLY_US_FAILED

3-Error

Applying upstream license failed

Unable to apply the upstream license

ubr10000

"Internal Error check license and report to TAC"

CMTS_LIC-6-CHANNEL_SHUTDOWN

6-Information

[chars] channel [dec] has been shutdown due to insufficient licenses

Unable to no shut the channel due to insufficient licenses

ubr10000

"Internal Error check number of licenses installed"

CMTS_LIC-6-CHANNEL_NO_SHUTDOWN

6-Information

[chars] channel [dec] has been restored to no shut

Restored previously shutdown channels to no shut state

ubr10000

"None"

CMTS_LIC-6-CHAN_NOSHUTFAIL

6-Information

[chars] channel [dec] no shut is not allowed due to insufficient licenses

Unable to no shut the channel due to insufficient licenses

ubr10000

"Internal Error check number of licenses installed"

CMTS_LIC-6-OUT_OF_RANGE

6-Information

LC [dec]/[dec] [chars] is already [dec]

License counters have reached boundary condition

ubr10000

"Internal Error check license and report to TAC"

CMTS_LIC-3-WORKING_INVALID

3-Error

Working linecard [dec]/[dec] has higher license than the configured protect

Working linecard has higher license than the protect so HCCP configuration is now invalid for the working linecard

ubr10000

"Upgrade the license on the protect or downgrade" " the license on the working"

CMTS_LIC-3-PROTECT_INVALID

3-Error

Protect linecard [dec]/[dec] has lower license than the configured working

Protect linecard has lower license than the working so HCCP configuration is now invalid for the protect linecard

ubr10000

"Upgrade the license on the protect"

CMTS_LIC-3-WORKING_PARTIAL

3-Error

Working Linecard [dec]/[dec] License has been restricted. Please upgrade Protect Linecard License first and then reload working for complete fulfillment

The working linecard license is now reduced because the working linecard license is higher than the protect linecard license

ubr10000

"Please upgrade the license on the protect and then reload the working linecard"

CMTS_LIC-3-LCD_PROCESS_CREATE_FAIL

3-Error

Could not create Update LCD process on Linecard [dec]/[dec]

The Line card license LCD update process create failed

ubr10000

LOG_STD_DDTS_TAC_DETAILS

CMTS_LIC-4-LICENSE_PENDING

4-Warning

License enforcement pending for Linecard [dec]/[dec]

The linecard license enforcement will be delayed until the linecard transitions to active

ubr10000

"No action required"

LCINFO-3-CRASH

3-Error

Line card in slot [dec]/[dec] crashed

The line card in the slot indicated crashed and sent a CRASH_START message to the PRE. The PRE is now waiting for the rest of the crash information from the line card to be sent via the BPE stack trace context version etc.. This should

ubr10k-sw

"Report this defect with as much information about the line card " "in question including the output of show context summary show " "context slot N and show tech-support N as well as the usual show " "tech-support from the PRE."

LCINFO-3-NOPROCESS

3-Error

Failed creating line card complete process

When creating the crash complete process for the crash information subsystem the create_process call failed. This should not happen. It is probably due to a software defect or hardware failure. This failure should only happen during initialization.

ubr10k-sw

"Rebooting the system should fix this. If the condition persists " "on subsequent reloads of the system a bug should be filed and " "the system should be reloaded with a different image."

LCINFO-3-TIMEOUT

3-Error

Timeout waiting for crash info from slot [dec]/[dec]

The crash information complete timer expired. When a line card crashes it sends information to the PRE for debugging and analysis. When the START OF CRASH message is recieved a timer is set for approx 10 seconds. The line card has 10 seconds to send all the crash information to the PRE. This is not a crash dump -- this is a small amount of information that usually includes context stack trace etc. It is less than 8K bytes of information. If an END OF CRASH information message is not received before the timer goes off the crash information record is closed contains partial information this message is

ubr10k-sw

"No action is required specifically because this message was " "displayed. Because the line card was crashing there might be " "other defects to report. If this message is seen without a line " "card crashing report this defect with the output of the usual " "commands includeing show tech-support on the PRE *AND* on the line " "card that didn't crash but was mentioned in this error " "message."

LCINFO-3-INVDEV

3-Error

Invalid line card number in BPE callback LC=[dec]/[dec]

The line card crash information subsystem on the PRE was called from the BPE subsystem with an invalid slot/subslot. The slot or subslot number is out of range. This indicates a software defect in the system.

ubr10k-sw

"Report this defect with as much information about the BPE " "subsystem as possible. There is no adverse effect to the PRE -- " "it ignores the bad callback and continues. If the problem " "persists reboot the router. It is unlikely but possible that " "the problem is due to bad BPE hardware somewhere in the system."

LCINFO-3-INVSTATE

3-Error

Line card crash server in bad state LC=[dec]/[dec]state=[dec]

-

-

-

LCINFO-4-UNXMSG

4-Warning

Unexpected crash info msg type [chars] in state [chars] LC=[dec]/[dec]

The line card crash information subsystem received an unexpected message for the state it is in. The state and message type are given in the error message. This does not have any adverse effect on the PRE since it ignores and/or recovers from this occurrence. Because the sender of these messages is a line card that is crashing it is not completely unbelievable that this might happen. The source of the crash on the line card is more interesting. If this occurs without a line card crashing it is due to a stray/errant BPE message that should be persued. This could also be due to a dropped BPE message.

ubr10k-sw

"Find the source of the crash on the line card if one was crashing " "when the message occurred. If no line card was crashing report " "this defect with as much information about the BPE subsystem and " "the line card crash information subsystem as possible. If this " "message persists rebooting the router might help remove this " "message."

LCINFO-3-NOBUFLC

3-Error

Could not malloc line card crash info buffer on PRE bufnum=[dec]size=[dec]

-

-

-

LCINFO-3-NOBUF

3-Error

Could not malloc line card crash structures on PRE size=[dec]

The PRE could not malloc data structures for line card crash data structures at startup time. This is not in and of itself a Serious problem but the underlying memory shortage at startup time will probably prevent the router from running well if at all.

ubr10k-sw

"Add more memory and/or debug the memory shortage problem."

LCINFO-4-TRUNC

4-Warning

Crash record [dec]=[chars] truncated expected=[dec]actual=[dec]

A line card crashed an was sending crash information to the PRE. The PRE received a CRASH RECORD START message that indicated the data would be \expected\ bytes long. Before that many bytes were received the PRE received another CRASH RECORD START message indicating the start of another record. The current record is marked as truncated and the next record is received but the anomoly is noted in this error message. This is a problem but because what started this process was a line card crashing this might only be a symptom of another underlying problem.

ubr10k-sw

"Report this defect with as much information about the BPE subsystem " "and the line card crash information subsystem possible."

LCINFO-3-NOLCHANGPROC

3-Error

Failed creating line card hang cure process

When creating the LC hang cure process for checking prolonged CLC down states the create_process call failed. This should not happen. It is probably due to a software defect or hardware failure. This failure should only happen during initialization.

ubr10k-sw

"Rebooting the system should fix this. If the condition persists " "on subsequent reloads of the system a bug should be filed and " "the system should be reloaded with a different image."

LCINFO-4-LCHUNG

4-Warning

Slot [[dec]/[dec]] down on last [dec] checks. HW RESET # [dec] ...

A line card can get hung in some IOS operation and is not able to recover or when rommon can get stuck while initiating tftp bootload. This is the time when an external monitoring process on RP checks for health of each line card. And if the line card is found stuck for more than 150 seconds a hardware reset is issued for that subslot. ANd while issuing a hard reset this error message is displayed onto the console.

ubr10k-sw

"Report this LC defect with as much information about the LC"

LCINFO-6-LCRESET

6-Information

PRE switchover. Reset empty slot [[dec]/[dec]]

When the standby PRE becomes active it resets all the slots which it thinks is empty. This prevents any linecards which was coming up during the PRE switchover from getting stuck

ubr10k-sw

""

UBR10K-4-MSGVERSION

4-Warning

Incompatible message version with slot [dec]

There is incompatibility between the the message version being sent by the line card and the message version used by the RP. This type of incompatibility could happen if the RP and Schooner line card are using different IOS versions due to an RP oir event

ubr10k-sw

"A microcode reload will solve the problem. "

UBR10K-0-SNMP_SET_IPC

0-Emergency

Schooner SNMP SET[dec]/[dec] [chars] failed

SNMP SET failed due to either IPC failure or line card SET failed

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-0-CLI_CONFIG

0-Emergency

CMTS[dec]/[dec]/[dec] schrp_cli_cmd failed in [chars]

Most likely S/W failure

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-0-CLI_CMD

0-Emergency

CMTS[dec]/[dec] [chars] failed

Most likely S/W failure

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-2-CLI_UNSUPPORTED_CMD

2-Critical

cable modem <ipaddr/macaddr> cmd not supported in Schooner

Currently unsupported command

ubr10k-sw

""

UBR10K-1-INITFAIL

1-Alert

Schooner subsystem init fails:[chars]

Schooner System initialization failure.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-IPCFAIL

1-Alert

Schooner subsystem IPC init fails for interface [chars] on [chars]: in [chars]

Schooner System IPC initialization failure.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-UNKEVT

1-Alert

Schooner subsystem unknown event:[dec] in [chars] for interface [chars]

Schooner System receive unknown event type.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-UNKREQ

1-Alert

Schooner subsystem unknown request:[dec]

Schooner System received unknown request type.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-UNKVECT

1-Alert

Schooner subsystem unknown vector:[dec]

Schooner System received unknown vector.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-SNMP_GETINDEX_FAIL

1-Alert

Cannot get SNMP physical Index for [chars]

Schooner System initialization failure.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-SNMP_SENDINFO_FAIL

1-Alert

Error sending SNMP info to [chars]

Schooner System initialization failure.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-1-SNMP_SENDCMD_FAIL

1-Alert

Error sending command type [dec] which [dec]

Schooner System initialization failure.

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10K-3-UTIL_CARD_UNINITIALIZED_ERROR

3-Error

Util card [dec] uninitialized

-

-

-

UBR10K-3-FPSUBINIT

3-Error

Unable to create subinterface [chars] for hw interface [chars] in the fast path

The system was unable to create the cable subinterface data structures in the fast path

ubr10k-sw

"Gather information about running configuration and amount of memory " "in the system and file a bug"

UBR10K-3-CFRNOMACRWIP

3-Error

Invalid IP address mapping for of CPE [enet] belonging to CM [enet]

Due to an inconsistency between the PXF FIB and the RP CPE data structures the packet classification state cannot be setup correctly

ubr10k-sw

"Try to force the CPE to get an IP address again. Also gather information " "about the cable modem and file a bug"

UBR10K-3-CFRNOINDEX

3-Error

Classifier control block index allocation failure

The system has run out of PXF resources to set up any new packet classifier state

ubr10k-sw

"This would typically happen only on a very overloaded system. So the only " "way out is to remove CMs from this system"

UBR10K-3-QALLOCFAIL

3-Error

Failure to allocate QoS queue for service flow %lu on [chars] MAC_addr [enet]

The system has run out of PXF queues

ubr10k-sw

"This would typically happen only on a very overloaded system. So the only " "way out is to remove CMs from this system"

UBR10K-6-ACFE_REJECTION

6-Information

ACFE has rejected QoS queue for service flow %lu on [chars] MAC_addr [enet] min_rate [dec] kbps rej_code [dec]

ACFE has rejected this CIR flow due to heavy CIR reservation on this or adjacent interfaces

ubr10k-sw

"This would typically happen only on a very overloaded interface." "If it persists on an interface try to provision more RF channels"

UBR10K-3-QALLOCFAIL_MCAST

3-Error

Failure to allocate MQoS queue for service flow %lu on [chars] Group [chars] Source [chars]

The system has run out of PXF queues

ubr10k-sw

"This would typically happen only on a very overloaded system. So the only " "way out is to remove CMs from this system"

UBR10K-6-ACFE_REJECTION_MCAST

6-Information

ACFE has rejected QoS queue for service flow %lu on [chars] Group [chars] Source [chars] min_rate [dec] kbps rej_code [dec]

ACFE has rejected this CIR flow due to heavy CIR reservation on this or adjacent interfaces

ubr10k-sw

"This would typically happen only on a very overloaded interface." "If it persists on an interface try to provision more RF channels"

UBR10K-3-QALLOCFAIL_INFO

3-Error

Failure to allocate QoS queue: [chars]

The system has run out of PXF queues providing additional debugging information

ubr10k-sw

"This would typically happen only on a very overloaded system. So the only " "way out is to remove CMs from this system"

UBR10K-1-POWCYCLE

1-Alert

Power cycle slot [dec]/[dec]

Recover from MC16S HW initialization failure.

ubr10k-sw

"If it happens to non-MC16S CLC copy the error message exactly as it" " appears and report it to your technical support representative."

UBR10K-1-CLCRESET

1-Alert

line card reset slot [dec]/[dec]

Recover from MC16S HW initialization failure.

ubr10k-sw

"If it happens to non-MC16S CLC copy the error message exactly as it " "appears and report it to your technical support representative."

UBR10K-1-JTAG_POWCYCLE

1-Alert

Power cycle slot [dec]/[dec]

Recover from 2020 power sequency error.

ubr10k-sw

"If it happens continuously copy the error message exactly as it " "appears and report it to your technical support representative. " "If it stops after one or a few power cycles " "the HW is recovered fully."

UBR10K-1-INVALIDSID

1-Alert

Dropping punted pkt from sid [dec] src [enet] hw [chars]

RP received a corrupt diverted packet from the cable linecard

ubr10k-sw

"Capture the logs and contact the TAC."

UBR10K-1-INVALIDPRIMSID

1-Alert

Dropping punted pkt from sid [dec] prim sid [dec] src [enet] hw [chars]

RP received a diverted packet with invalid primary sid from the cable linecard

ubr10k-sw

"Capture the logs and contact the TAC."

UBR10K-1-INVALID_DIVHDR

1-Alert

Invalid diversion hdr on pkt: cause [dec] channel 0x[hec] length [dec]

RP received a corrupt diverted packet from the cable linecard

ubr10k-sw

"Capture the logs and contact the TAC."

UBR10K-4-INVALID_PKT_FILTER_GROUP

4-Warning

Invalid [chars]_filter_group [dec] IP_addr = [inet]

CM-config-file specifies a filter-group greater than the platform maximum

ubr10k-sw

"Capture the logs and contact the TAC."

UBR10K-3-ROMMON_VERSION_ERROR

3-Error

Linecard Slot [dec]/[dec] version error: [chars]

Failed to find bundled or programmed ROMMON version.

ubr10k-sw

"Capture the logs and contact the TAC." "If persistent replace the card"

UBR10K-5-ROMMON_UPDATE_START

5-Notice

ROMMON [chars] from version [dec] to version [dec] started for slot [dec]/[dec]

Linecard ROMMON upgrade start.

ubr10k-sw

LOG_STD_ACTION

UBR10K-5-ROMMON_UPDATE_DONE

5-Notice

ROMMON update [chars] for slot [dec]/[dec]

Linecard ROMMON update done.

ubr10k-sw

LOG_STD_ACTION

UBR10K-3-ROMMON_UPDATE_ERROR

3-Error

Linecard Slot [dec]/[dec] update error: [chars]

Linecard ROMMON update error.

ubr10k-sw

"Capture the logs and contact the TAC." "If persistent replace the card"

UBR10K-4-ROMMON_UPDATE_MUTED

4-Warning

Linecard Slot [dec]/[dec] ROMMON update is temporarily disabled due to a limit on unsuccessful attempts. The card may not have the latest firmware

ROMMON update is temporarily blocked to prevent multiple reloads

ubr10k-sw

"Wait 10 min reset the linecard to restart ROMMON upgrade" "Capture the logs and contact the TAC."

UBR10K-4-ROMMON_UPDATE_POSTFALPOS_MUTED

4-Warning

Linecard Slot [dec]/[dec] ROMMON update from [dec] to [dec] is temporarily disabled due to a limit on consequtive attempts. The card may not have the latest firmware

ROMMON update is temporarily blocked to prevent multiple reloads

ubr10k-sw

"Wait 10 min reset the linecard to restart ROMMON upgrade" "Capture the logs and contact the TAC."

UBRIFCON-3-NOPROC

3-Error

Unable to create the if-console background process

The system wants to create a background process to handle if-console data from the line cards but is unsuccessful.

ubr10k-sw

"Gather information about the number of processes running and " "amount of memory in the system and file a bug."

UBRIFCON-3-NOQUEUE

3-Error

Unable to create the if-console background queue

The system wants to create a background process queue to handle if-console data from the line cards but is unsuccessful.

ubr10k-sw

"Gather information about the number of processes running and " "amount of memory in the system and file a bug."

UBR10KTCC-5-ACTIVE_TCC

5-Notice

[chars] card [dec]/[dec] is active with [chars] as clock reference

The TCC Card became active

ubr10k-sw

"Information only"

UBR10KTCC-2-LOS

2-Critical

Loss of signal with clock reference TCC in [chars] card [dec]/[dec]

The TCC card clock reference was lost

ubr10k-sw

"Check reference source"

UBR10KTCC-6-CHG_CLK_REF

6-Information

Clock reference source set to [chars] for [chars] card [dec]/[dec] by process [chars]

Three reasons for the change in clock reference. 1 LOS of previous source reference for TCCplus card

ubr10k-sw

"Check reference source TCCplus Information onlyDTCC"

UBR10KTCC-2-BADTCC

2-Critical

TCC card in [dec]/1 put under maintenance due to: [chars]

There could be some failure in the MTSS of the TCC card

ubr10k-sw

"Replace TCC card"

UBR10KTCC-1-NOTCC

1-Alert

No working TCC card available in the system

There is no TCC card or there could be some failure in the MTSS of the TCC card and it is put under maintanence

ubr10k-sw

"Replace TCC card"

UBR10KTCC-4-BADCLK_STANDBY_TCC

4-Warning

No available external clock reference on the standby DTCC card [dec]/[dec]

The TCC card clock reference is lost or bad

ubr10k-sw

"Check reference source on the standby DTCC card"

UBR10KTCC-3-BLKCMD

3-Error

Schooner System IPC failure for TCC card

c10k_card_send_blocking_cmd failed

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10KTCC-3-EVNTLEN

3-Error

TCC card Event internal error [chars] [dec] [dec]

Internal Event error in TCC card

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10KTCC-1-LCLOSC

1-Alert

Cable Line Card [dec]/[dec] using the local oscillator

Error in the clock received on the BackPlane

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10KTCC-1-BADCLK

1-Alert

Cable Line Card [dec]/[dec] reports Bad Clock Status for [chars] card in [dec]/1

Error in the clock received on the BackPlane

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative. " "Check output of 'show clc-clk-status' command"

UBR10KTCC-1-SWTCHERR

1-Alert

Unable to switch TCC card configuration. Other card is not present or in Maintenance

Other card is not present or in Maintenance state

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10KTCC-4-OIRERR

4-Warning

TCC OIR state machine warning: attempt to restart working card\n

OIR Start is called twice back-to-back

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10KTCC-3-DTIERR

3-Error

DTI interface Error code [dec] function [chars]

Error return value on call of DTI component function

ubr10k-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR10KTCC-5-DTISLOT

5-Notice

DTCC slot [dec]/[dec]: card role changed to [chars]\n

Change in role of TCC slot

ubr10k-sw

"Check DTI link/cable"

UBR10KTCC-6-DTIPORTCLIENT

6-Information

DTCC slot [dec]/[dec] port [dec] DTI client status changed to [chars] [chars]\n

Change in client status of DTI port

ubr10k-sw

"Check DTI link/cable"

UBR10KTCC-6-DTIPORTSERVER

6-Information

DTCC slot [dec]/[dec] port [dec] DTI server status changed to [chars] external clock source: [chars]\n

Change in server status of DTI port

ubr10k-sw

"Check DTI link/cable"

UBR10KTCC-6-DTIPORTPHYS

6-Information

DTCC slot [dec]/[dec] port [dec] DTI physical status changed: Link status:[chars] frame error rate: [chars]\n

Change in frame error rate or link status of DTI link

ubr10k-sw

"Check DTI link/cable"

UBR10KTCC-4-DTCC_CLOCK_WARNING

4-Warning

Active DTCC in slot [dec]/[dec] doesn't have the latest firmware 0x[hec]. This may impact system behavior in selected clock mode\n

Active DTCC doesn't have the latest firmware

ubr10k-sw

"If CMTS doesn't contain dual DTCC cards then the " "firmware will not be auto-upgraded. \n" "Do manual upgrade using 'cable clock update'"

UBR10KTCC-5-DTCC_UPGRADE

5-Notice

DTCC card in slot [dec]/[dec] will be upgraded from 0x[hec] to version 0x[hec]. PLEASE DO NOT INTERRUPT DURING THE UPGRADE PROCESS. Estimated upgrade time [dec] minutes.\n

DTCC upgrade information

ubr10k-sw

"None"

UBR10KTCC-4-DTCC_OLD_HW

4-Warning

DTCC slot [dec]/[dec] FPGA upgrade needed. Card is outdated and cannot be auto-upgraded. H/W revision is 0x[hec] minimum requirement is 0x[hec]\n

The DTCC card has old hardware and cannot be upgraded

ubr10k-sw

"Replace TCC card"

UBR10KTCC-4-DTCC_OLD_FW

4-Warning

DTCC slot [dec]/[dec] FPGA upgrade needed. Card is outdated and cannot be auto-upgraded. Main EPLD version is 0x[hec] minimum requirement is 0x[hec]\n

The DTCC card has old firmware and cannot be upgraded

ubr10k-sw

"Replace TCC card"

UBR10K-3-VOLTABNORMAL

3-Error

The PEM [dec] voltage value [dec] is abnormal

Chassis voltage value is abnormal

ubr10k-sw

LOG_STD_ACTION

UBR10K-0-LCPOWEREDOFF

0-Emergency

Linecard Slot [dec]/[dec] device has reached critical temperature [dec] Linecard powered off Critical Threshold [dec] Last Temperature [dec]

Linecard temperature value is critical

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-CM_INCONSISTENCY

6-Information

CM state inconsistency [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received INIT_CM for an online CM Copy the message and report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-STDBY_CM_INCONSISTENCY

6-Information

CM sync received [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received sync message on secondary PRE for mismatched entry This problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-HCCP_CM_INCONSISTENCY

6-Information

CM sync received [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received sync message on secondary PRE for mismatched entry This problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-DSD_SRV_FLOW_ERROR

6-Information

SFID found: SFID [dec] type [dec] MAC [enet][enet] prim_sid [dec][dec]

The RP and LC have different service-flows for the same SFID. The problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-DS_SFID_INCONSISTENCY

6-Information

DS-SF found: SFID [dec] type [dec] MAC [enet][enet] prim_sid [dec][dec]

The RP and LC have different downstream service-flows for the same SFID. The problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-US_SFID_INCONSISTENCY

6-Information

US-SF found: SFID [dec] type [dec] sid [dec][dec] MAC [enet][enet] prim_sid [dec][dec]

The RP and LC have different upstream service-flows for the same SFID. The problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBR10K-6-COMPAT_IGNORED

6-Information

OIR compatibility is disabled because [chars]

OIR compatibility is disabled because of a conflict with another feature.

ubr10k-sw

"Disable OIR compatability or the conflicting feature."

UBR10K-6-COMPAT_NO_CFG

6-Information

OIR compatibility does not support the [chars] in slot [dec]/[dec]. [chars]

A line card that is supported by the OIR compatibility feature is not not supported in the specified slot/subslot.

ubr10k-sw

"This is most likely a software problem and should be reported to development. OIR compatibility for the given slot/subslot should be disabled until the problem is resolved."

UBR10K-6-COMPAT_SHUTDOWN_CARD

6-Information

Failed to restore the configuration for [chars].

A CMTS interface has been placed in the shutdown state by the OIR-compatibility feature because a saved configuration could not be used on a compatible line card. This will happen during an OIR operation if the replacement card provides only a subset of the functionality of the original card and the previous card was configured for features that are not backward compatible.

ubr10k-sw

"Manually reconfigure the interface to match the line card's capability."

UBR10K-6-COMPAT_NEW_CARD

6-Information

The [chars] in slot [dec]/[dec] has been replaced by a [chars].

A line card has been replaced by a compatible line card.

ubr10k-sw

"This is not an error."

UBR10K-6-STATESYNC

6-Information

Redundancy state synchronization failure slot [dec]/[dec] - [chars]

A failure occurred in trying to synchronize GE state information

ubr10k-sw

LOG_STD_RECUR_ACTION

UBR10K_CLC_GE-3-SW_SLOT_ERR

3-Error

slot [dec]/[dec]: [chars]

software error in CLC GigE interface

ubr10k-sw

LOG_STD_ACTION

UBR10K_CLC_GE-3-SW_CTRL_ERR

3-Error

slot [dec]/[dec] controller [dec]: [chars]

software error in CLC GigE interface

ubr10k-sw

LOG_STD_ACTION

UBR10K-3-CNNR_DSYNC

3-Error

Dynamic sync failed for [chars]:U[dec] connector mapping expect:[dec] current:[dec] cause:[chars]

URM failed to sync connector-receiver mapping from active RP to stby RP.

ubr10k-sw

"clear and re-configure the connector command for the affected MD:US." "Or reload stby RP"

UBR10K-5-CNNR_DSYNC_NOTICE

5-Notice

Dynamic sync notice for [chars]:U[dec] connector mapping expect:[dec] current:[dec] cause:[chars]

URM connector-receiver mapping from active RP to stby RP notice no service impact

ubr10k-sw

"This is only a notice no service impact"

UBR10K-4-HW_ASSIST_WDOG_FAILURE

4-Warning

Send lchung packet to Card[dec]/[dec] failed

send lchung packet to line card failure maybe due to low buffer

ubr10k-sw

LOG_STD_ACTION

UBR10K-4-HW_ASSIST_WDOG_TIMEOUT

4-Warning

Card[dec]/[dec] HW assist watchdog timeout\n

PRE send LCHung packet to Line card in extend time maybe HW assist watchdog not supported in Line card or disabled.

ubr10k-sw

LOG_STD_ACTION

UBR10K-3-IRONBUS_BAD_CHECKSUM

3-Error

Bad checksum in ironbus IPC packetexpected 0x[hec] actual 0x[hec].

-

-

-

UBR7200-2-NOMEMORY

2-Critical

Failure to create new IPv6 entry %P

Unable to malloc a buffer to create a new entry to add Ipv6 addr

cmts-platform

"Enter a show chunks command and report the output along with this " "error message to your technical support representative."

UBR7200-3-BRIDGE_DELETE

3-Error

Interface [chars] error in deleting address [dec] from host tables

An internal software error occurred during CMTS tables management

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-IDB_MISMATCH

3-Error

DHCP IP Address Assign Mismatch MAC [enet] on [chars] assigned to [chars] with [inet]

A DHCP server assignment error

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-INTERCEPT

3-Error

Interface [chars] Failed to send intercept packet to server [inet]:[dec]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-MACADDRERR

3-Error

DHCP Msg with non unicast MAC address. Master Interface [chars] Input Interface [chars] SID = [dec] MAC = [enet]

Most likely sw error

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-MONITOR_ACCESS_FILTER

3-Error

Null access list

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-MONITOR_EMPTY

3-Error

Unable to allocate packet with rx_type = [dec]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-MONITOR

3-Error

Interface [chars] Failed to send monitored packets

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-0-CPUCARD

0-Emergency

CMTS[dec]/[dec] Init failed CSR[dec]=0x%04x.

Most likely Hardware failure

ubr7200

"Replace defective Line Card"

UBR7200-4-RECALLED_NPE

4-Warning

Old version NPE-175/225 with Rev = 0x%02x system controller. Contact upgrades-info@cisco.com for replacement

NPE board has been recalled due to an errata in the system controller chip.

ubr7200

"Replace NPE-175/225 Board"

UBR7200-1-DISCOVER

1-Alert

Only found [dec] interfaces on bay [dec] shutting down bay

Most likely system or hardware failure

ubr7200

"Replace Line Card"

UBR7200-3-NOTCMTS

3-Error

Device reported [hex]

Most likely hardware failure

ubr7200

"Replace defective hardware"

UBR7200-3-OWNERR

3-Error

CMTS[dec]/[dec] Buffer ownership error pak=0x[hec].

Most likely hardware failure

ubr7200

"Replace defective board"

UBR7200-3-SPIERRW_CHID

3-Error

Invalid Channel ID[chars]: chid=0x%02x cmd=0x%02x regaddr=0x%02x

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-NEG_PENDING

3-Error

NEGATIVE DECREMENT OF PENDING STATS on [chars] for [enet]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-SPIERRW

3-Error

SPI PENDING WRITE ERROR[chars]: spistat=0x%02x chid=0x%02x cmd=0x%02x

Write error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-SPIERRR

3-Error

SPI PENDING READ ERROR[chars]: spistat=0x%02x chid=0x%02x cmd=0x%02x

Read error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-SPIERRNRD

3-Error

SPI PENDING NO READ DATA[chars]: spistat=0x%02x chid=0x%02x cmd=0x%02x

Read error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-SPIERRRBS

3-Error

SPI BUS READ 0x%02x BYTES SHORT[chars]: spistat=0x%02x chid=0x%02x

Read error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-DBPLX9080ERR

3-Error

Plx9080 id read 0x[hec]expect 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBPLX9050ERR

3-Error

Plx9050 id read 0x[hec]expect 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBFPGAERR

3-Error

XILINX not up reset reg is 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-5-DBDSPUP

5-Notice

Handshake DSP is successful after [dec] ms delay

DSP is up and running

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPERR1

3-Error

DSP SRAM failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR2

3-Error

DSP SRAM semaphore failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR3

3-Error

DSP side dual-port SRAM failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR4

3-Error

DSP FLASH memory failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR5

3-Error

DSP failed to respond to Host Handshake

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPIDERR

3-Error

DSP id read 0x[hec]expect 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-5-DBDSPRECOVER1

5-Notice

Trying to switch to backup dsp image

Trying to recover DSP using backup image

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-DBDSPRECOVER2

5-Notice

Switching to backup dsp image succeeded

Switching to backup dsp image succeeded

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-DBDSPRECOVER3

5-Notice

Recovering and switching back to regular dsp image succeeded

DSP recover operation using backup image succeeded

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPERR6

3-Error

Switching to backup dsp image failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR7

3-Error

Switching again to regular dsp image failed

Daughter board regular image corruption failure

ubr7200

"Replace with BACKUP image"

UBR7200-6-DBDSPVERSION

6-Information

Current DSP version : [dec] DSP flash version : [dec]

The current code version and the version DSP booted up with

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-DBDSPDOWNLOADSTART

6-Information

Downloading dsp code initiated

Downloading dsp code started

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-DBDSPDOWNLOADDONE

6-Information

Downloading dsp code completed

Downloading dsp code completed

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDOWNLOADERR1

3-Error

DSP FAILED TO RESPOND TO INIT_DOWNLOAD CMD.

Failed initiating DSP downloading

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBDSPDOWNLOADPASS1

3-Error

INIT DOWNLOAD OF DSP F/W PASS.

The DSP firmware download initiation was successful

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDOWNLOADPASS2

3-Error

DOWNLOAD OF DSP F/W SUCCESS.

The DSP firmware download was successful

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-REMOVE_OVERLAP_ENTRY

3-Error

\nREMOVE OVERLAP ENTRY:[chars] Found MAC:[enet] from:[chars] MAC:[enet] IP:[inet] IPv6:%P SID:[dec] found sid:[dec] ptr_sid:[dec]

Remove stale entry overlap check error

cmts

"Check the bucket info of CM/CPE." "Copy the error message exactly as it appears" "and report it to your technical support representative."

UBR7200-3-DBDSPDOWNLOADERR2

3-Error

Failed downloading.

Failed DSP downloading

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBDSPDOWNLOADERR3

3-Error

FAILED DOWNLOADING OF DSP FW DUE TO CHECKSUM FAILURE.

Failed last step of DSP downloading

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBDSPDOWNLOADPASS3

3-Error

END DOWNLOAD OF DSP F/W SUCCESS.

The DSP firmware end download was successful

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDEAD

3-Error

AWACS Slot [dec] is dead

Daughter board DSP hungs

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBFPGADLERR

3-Error

[chars]

XILINX FPGA download failure

ubr7200

"Reload image if still fail replace defective line card"

UBR7200-5-USJIB3NBC

5-Notice

Interface [chars] U[dec] INFO: receives collision no burst

A collision happens on an upstream channel

ubr7200

"If consistently offending modems/channel can be found by" "test cable jib3us show intr-logs 1 on LC console" "and show cable modem on the interface"

UBR7200-5-USIPLCHG

5-Notice

Interface [chars] U[dec] input power level changed to [dec] dBmV

The upstream channel input power level was changed.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USIPLINVALID

5-Notice

Interface [chars] U[dec] input power level is outside of valid range due to channel width change

The upstream channel input power level is invalid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USCWCHG

5-Notice

Interface [chars] U[chars] channel width changed to [dec] kHz

The upstream channel width was changed.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-EAEREJECT

5-Notice

EAE registration rejected CM [enet] on Interface [chars]

CM registration rejected to force EAE policy.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USFREQCHG

5-Notice

Interface [chars] U[chars] changed to Freq [dec].%03u MHz

The upstream channel frequency was changed.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USCONTHOP

5-Notice

Interface [chars] U[dec] frequency hop started

All modems just went offline. This message logs the start of frequency hop.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USCONTEND

5-Notice

Interface [chars] U[dec] frequency hop ended at [dec].%03u MHz

At least one modem came back online. This message logs the abort of frequency hop.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USMODINVALID

5-Notice

Protect Interface [chars] U[dec] using default profile [dec] because modulation profile is undefined.

This means that Modulation Profile was not defined on Protect UBR7200

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USMODCHANGE_WARN

5-Notice

Interface [chars] U[dec] new profile [dec] is [chars] than old profile [dec]

Print warning message about the increase or decrease in through-put

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USMODCHANGE

5-Notice

Interface [chars] U[dec] dynamic modulation changed to [chars]

Dynamic modulation change from QAM to QPSK and vice-versa.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BADUSPORT

3-Error

Interface [chars] U[dec] invalid highest port number is U[dec]

Upstream port number must be valid.

ubr7200

"Redo command with valid upstream port number."

UBR7200-5-UPDOWN

5-Notice

Interface [chars] U[chars] changed state to [chars]

The upstream port was brought up or down.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-TIMESCH

5-Notice

Time scheduled event spectrum group [dec] [chars]

A time scheduled reconfiguration event occurred on an interface.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USIPLFIX

5-Notice

Interface [chars] U[dec] input power level fixed at [dec] dBmV

Setting the upstream frequency to a fixed value caused the upstream input power level to assume a fixed value.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BADFFTINTERRUPT

3-Error

BCM3138 chip [dec] dma interrupt error.

FFT dma interrupt error occured.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BADFFTSTATE

3-Error

BCM3138 chip [dec] is in wrong state [dec] expected state [dec]

Impossible state has been reached.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-WRONG3138CHIP

3-Error

BCM3138 current chip [dec] desired chip [dec]

Wrong BCM3138 chip has been selected.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-HUNGFFTSTATE

3-Error

BCM3138 chip [dec] is not idle for [dec] retries

BCM3138 FFT processor stuck

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SPECMGMTGRP

4-Warning

Spectrum group [dec] with discrete frequency is not fully supported on interface [chars]

The spectrum management group is not fully supported

ubr7200

"Suggest convert discrete frequency to frequency band in the group"

UBR7200-0-LOWPOWERCPU

0-Emergency

uBR requires CPU card type NPE150 or higher

NPE100 is not supported in uBR

ubr7200

"Upgrade CPU card to NPE150 or higher"

UBR7200-3-BADARPDELETE

3-Error

Tried to remove arp entry for [inet] that is not dynamic

Tried to delete non-dynamic arp entry - possible spoof attempt

ubr7200

"Look for possible CMTS IP address spoofing attempt"

UBR7200-3-BADARPREPLY

3-Error

Interface [chars] ARP reply from invalid source. Expected SID=[dec] Actual SID=[dec]

There might be a spoofing attempt going on

ubr7200

"Look for possible spoofing attempt"

UBR7200-3-BADARPREQUEST

3-Error

Interface [chars] ARP request from invalid source on [chars]. IP=[inet] MAC=[enet]\n Expected SID=[dec] Actual SID=[dec]

This is a proxyed ARP reply or a spoofing attempt received on the CMTS upstream.

ubr7200

"Look for possible proxyed ARP reply or spoofing attempt"

UBR7200-5-CLEAR_ARP_TABLE

5-Notice

Clearing all ARP entries

All the entries have been cleared

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-CLEAR_ARP_INTERFACE

5-Notice

Clearing all ARP entries for interface [chars]

All the entries have been cleared

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-BADIPSOURCE

6-Information

Interface [chars] IP packet from invalid source. IP=[inet] MAC=[enet] Expected SID=[dec] Actual SID=[dec]

There might be a spoofing attempt going on.

ubr7200

"Look for possible spoofing attempt"

UBR7200-6-BADIPASSIGNMENT

6-Information

[chars] dropped : Interface [chars] Mac [enet] SID [dec] L3_Interface [chars] \n IP [inet] already assigned to MAC=[enet] Interface [chars] SID [dec]

There might be an incorrect DHCP assignment going on.

ubr7200

"Look for possible DHCP server misconfiguration"

UBR7200-6-BADIPSOURCE_BUNDLE

6-Information

Interface [chars] IP packet from invalid source. IP=[inet] MAC=[enet] Expected Interface=[chars] SID=[dec] Actual Interface=[chars] SID=[dec]

There might be a spoofing attempt going on.

ubr7200

"Look for possible spoofing attempt"

UBR7200-3-DOCSIS_SYNC_SF

3-Error

cminstp is NULL: [chars].

No valid cminstp is found for sid referenced in this checkpoint msg message will be dropped

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-SPOOFEDIP

3-Error

Rejecting IP=[inet] [chars] sid [dec]: Address configured on [chars]

CMTS glean function received overlapping ip address info

ubr7200

"Check for spoofing: CPE may be using CMTS IP addr"

UBR7200-3-SPOOFEDMAC

3-Error

Investigating MAC=[enet] [chars] sid [dec]: Original MAC on sid [dec] [chars]

CMTS glean function received overlapping mac address info

ubr7200

"Check for spoofing: CPE may be reusing mac addr"

UBR7200-3-HOTLISTMAC

3-Error

Investigating MAC=[enet] sid [dec] interface [chars]: MAC blocked

CMTS glean function received blocked mac addr

ubr7200

"Check for spoofing: CPE using blocked mac addr"

UBR7200-4-OVERLAPIP

4-Warning

Interface [chars] IP address [inet] %P from MAC [enet] is already in use on [chars]. SID = [dec]

There might be a spoofing attempt going on.

ubr7200

"Look for possible spoofing attempt"

UBR7200-3-ZEROMAC

3-Error

Error: Mac addr is zero sent to CMTS [chars]: [chars] IP [inet] SID [dec]!

Miscreant client detected.

ubr7200

"Contact Cisco with this log message"

UBR7200-3-ZEROIP_AND_MAC

3-Error

Error: Both IP & mac addr are zero sent to CMTS add entry routine: [chars] SID [dec]!

IPC message seems to have been clobbered.

ubr7200

"Contact Cisco with this log message"

UBR7200-3-ZEROMAC_IPV6

3-Error

Error: mac addr is zero sent to CMTS add entry routine: [chars] SID [dec] %P!

IPC message seems to have been clobbered.

ubr7200

"Contact Cisco with this log message"

UBR7200-3-ZEROIPV6

3-Error

Error: IPv6 addr is zero sent to CMTS add entry routine: [chars] SID [dec] [enet]!

IPC message seems to have been clobbered.

ubr7200

"Contact Cisco with this log message"

UBR7200-4-OVERLAPIP_CM

4-Warning

Interface [chars] IP address [inet] %P assigned to CM [enet] has been reassigned.

There might be DHCP server configuration error.

ubr7200

"Check DHCP server configuration"

UBR7200-4-OVERLAPIP_CM_CPE

4-Warning

Interface [chars] SID [dec] IP address [inet] %P assigned to CM [enet] is being reassigned to its CPE [enet].

There might be DHCP server configuration error.

ubr7200

"Check DHCP server configuration"

UBR7200-3-DHCP_IP_ASSIGN_ERROR

3-Error

IP address [inet] for the host [enet] is already assigned to CM [enet].

There might be DHCP server configuration error.

ubr7200

"Check DHCP server configuration"

UBR7200-5-MAXHOST

5-Notice

Interface [chars] New host with IP address [inet] and MAC [enet] on SID [dec] CM [enet] is ignored in [chars] path.

-

-

-

UBR7200-5-MAXCPE_IP

5-Notice

Interface [chars] CPE IPs [dec] Max CPE IPs [dec] over limit. New host with MAC [enet] on SID [dec] CM [enet] is ignored.

-

-

-

UBR7200-4-NOTLEARNABLE

4-Warning

New CPE [enet] behind modem [enet] on interface [chars] is ignored: [chars]. Count [dec]

The CPE is not learnable due to provisioning.

ubr7200

"Provisioning failure. Please check configuration"

UBR7200-3-HOST_DB_CORRUPTED

3-Error

Host database corrupted under interface [chars] for MAC [enet] sid [dec] ip [inet].

CMTS host database corruption.

ubr7200

"Contact Cisco TAC"

UBR7200-4-UNKNOWNSID

4-Warning

SID cannot be resolved from the leasequery reply for IP [inet]\n interface [chars] mac [enet] sid [dec] for DHCPACK

Relay-agent option might not be configured.

ubr7200

"Make sure relay-agent option is configured. Also " "make sure save-relay-agent-data is enabled on CNR."

UBR7200-4-DHCPLQSIDMISMATCH

4-Warning

Source Verify of pkt from host [enet] [inet] sid [dec] does not match LQ Relay Info from server [inet] for CM [enet] sid [dec] on interface [chars]

SID of packet does not match sid of mac addr in relay-agent info from DHCP server.

ubr7200

"Manually verify lease info on DHCP server against current " "sid of the host."

UBR7200-4-DHCPV6LQSIDMISMATCH

4-Warning

Source Verify of pkt from host [enet] %P sid [dec] does not match LQ Relay Info from server %P for CM [enet] sid [dec] on interface [chars]

SID of packet does not match sid of mac addr in relay-agent info from DHCPv6 server.

ubr7200

"Manually verify lease info on DHCPv6 server against current " "sid of the host."

UBR7200-4-FAILED_DS_SID_LOOKUP

4-Warning

Failed to find host in DS on int [chars] with SID # [dec] IP = [inet] MAC = [enet]

Failed to process Lease-Query response for host

ubr7200

"Check if host is provisioned on dhcp server."

UBR7200-3-ZOMBIESID

3-Error

SID [dec] macaddr [enet] us_channel_id [dec] rng_list_id [dec] ds_time_stamp %llu rngpoll_timeout %llu now %lu last_ranging %lu stn_mtn=[dec] cont_mtn=[dec] pending=[dec].

SID instance didn't get cleanup after modem is gone.

ubr7200

"Call TAC and show him/her the log."

UBR7200-4-NOCPUVER

4-Warning

Invalid CPU ID assuming revision 1

CPU Revision ID is unreadable.

ubr7200

"Update CPU board."

UBR7200-3-CONFIG

3-Error

Exceeds [dec] [chars]

The total bandwidth of fast and medium bandwidth port adapters exceed the rated capacity of this system.

ubr7200

"Refer to the configuration guidelines for the maximum allowed " "high and medium bandwidth port adapters for the system."

UBR7200-4-VERSION_MISMATCH

4-Warning

Midplane data version mismatch.

Data stored in midplane is out of date and needs update.

ubr7200

"Contact technical support to update your system."

UBR7200-4-MACBLKSIZE

4-Warning

Unknown MAC address block size.

Data stored in midplane is bad or incomplete.

ubr7200

"Contact technical support to update your system."

UBR7200-3-CHASSIS

3-Error

Unknown chassis model.

Data stored in midplane is bad or incomplete.

ubr7200

"Contact technical support to update your system."

UBR7200-3-SLOTS

3-Error

Number of slots in chassis is undefined.

Data stored in midplane is bad or incomplete.

ubr7200

"Contact technical support to update your system."

UBR7200-3-NOMAC

3-Error

Can't allocate MAC address for interface [dec]/[dec]

Your system is out of available MAC addresses.

ubr7200

"Contact technical support."

UBR7200-4-COOKIE

4-Warning

Corrupt or missing MAC address cookie\n using random base [enet]

Data stored in midplane is bad.

ubr7200

"Contact technical support to update your system."

UBR7200-0-VOLTLOW

0-Emergency

[chars] measured at [chars] is too low: shutdown voltage [chars]

Current voltage exceeds the min shutdown voltage

ubr7200

"Determine cause of the low voltage and correct if possible."

UBR7200-0-VOLTHIGH

0-Emergency

[chars] measured at [chars] is too high: shutdown voltage [chars]

Current voltage exceeds the max shutdown voltage

ubr7200

"Determine cause of the high voltage and correct if possible."

UBR7200-0-TEMPHIGH

0-Emergency

[chars] measured at [chars] is too high: shutdown temperature [chars]

Current temperature exceeds the max shutdown temperature

ubr7200

"Determine cause of the high temperature and correct if possible."

UBR7200-3-INVALIDSID

3-Error

CR10K_REQ_API_DHCP_CLEAR: Invalid sid [dec] for mac address [enet]

There might be an IPC problem

ubr7200

"Look for possible spoofing attempt"

UBR7200-3-UNASSIGNEDSID

3-Error

CR10K_REQ_API_DHCP_CLEAR: Unassigned sid [dec] for mac address [enet] sid found [dec]

There might be an IPC problem

ubr7200

"Look for possible spoofing attempt"

UBR7200-6-GRDIDX_LOG

6-Information

DS [dec]/[dec]/[dec] Index [dec] DSID 0x[hec] SID [dec] SF_BU [dec] FW [chars] [dec]/[dec]/[dec]:[dec] MD Ca[dec]/[dec]/[dec] [chars] [chars]

Debug message for Guardian index operations

ubr10000

LOG_STD_NO_ACTION

UBR7200-6-MDIDX_LOG

6-Information

GRD [dec]/[dec] Index [dec] SID [dec] SF [dec] FW [chars] [dec]/[dec]/[dec]:[dec] MD [chars] [chars] [chars]

Debug message for MAC Domain index operations

ubr10000

LOG_STD_NO_ACTION

UBR7200-3-UBRIPCRECVERR

3-Error

Internal RP-CLC/CLC-CLC IPC receive error from [dec]/[dec]

Internal IPC receive error\n

ubr10000

LOG_STD_NO_ACTION

UBR7200-3-UBRIPCSENDERR

3-Error

Internal RP-CLC/CLC-CLC IPC send error from [dec]/[dec]

Internal IPC send error\n

ubr10000

LOG_STD_NO_ACTION

UBR7200-6-CREATE_MAUTH_PROF

6-Information

<132>CMTS[DOCSIS]:<89010300> Multicast Profile [chars] created for CM Mac [enet].

CMTS automatically creates an IP Multicast Profile

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-MCAST_SESS_NOT_AUTH

6-Information

<132>CMTS[DOCSIS]:<89010200> Multicast session [chars] is not authorized for CM [enet]

Default configured action for IGMP Join is denied or the matching session rule's action is denied or the maximium session limit for the modem has been reached.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-IPV6SOCKETFAIL

3-Error

IPv6 TFTP server socket

Could not open the IPv6 TFTP server socket

ubr7200

"Make sure the /"ip tftp-server /" CLI is not configured"

UBR7200-4-NOCFGFILE

4-Warning

Cannot read modem config file [chars] from [inet]: [chars]

Configuration file for the cable modem cannot be read

ubr7200

"Make sure the config file is accesable to the CMTS"

UBR7200-4-BADCFGFILE

4-Warning

Modem config file [chars] at [inet]: [chars]

Configuration file for the cable modem has problems

ubr7200

"Make sure the config file is proper"

UBR7200-4-NOCFGFILE_V6

4-Warning

Cannot read modem config file [chars] from %P: [chars]

Configuration file for the cable modem cannot be read

ubr7200

"Make sure the config file is accesable to the CMTS"

UBR7200-4-BADCFGFILE_V6

4-Warning

Modem config file [chars] at %P: [chars]

Configuration file for the cable modem has problems

ubr7200

"Make sure the config file is proper"

UBR7200-4-TFTP_DATA_LEN_ERROR

4-Warning

The length of TFTP DATA packet exceeded negotiated/default block size of [dec] while downloading [chars] from [inet]

TFTP DATA packet received exceeded its negotiated/default block size

ubr7200

"Make sure that the block size of the TFTP DATA packets" "does not exceed the negotiated/default block size"

UBR7200-4-CMMARKED

4-Warning

Cable Modem [enet] in [chars] attempted theft of service

Configuration file for the cable modem has problems

ubr7200

"Cable modem attempted to steal service"

UBR7200-4-CMLOCKED

4-Warning

Cable Modem [enet] in [chars] locked due to [chars] theft of service

Configuration file for the cable modem has problems

ubr7200

"Cable modem attempted to steal service"

UBR7200-4-OACKERROR

4-Warning

TFTP Option Negotiation Error for [chars] file at [inet]: [chars]

TFTP OACK packet is malformed or wrong options appended

ubr7200

"Make sure TFTP Server supports TFTP Options"

UBR7200-4-OACKERROR_V6

4-Warning

TFTP Option Negotiation Error for [chars] file at %P: [chars]

TFTP OACK packet is malformed or wrong options appended

ubr7200

"Make sure TFTP Server supports TFTP Options"

UBR7200-5-BADMNCSMSG

5-Notice

Invalid DOCSIS Message Type [dec] received from the CM [enet] for interface [chars]

-

-

-

UBR7200-5-UNREGSIDTIMEOUT

5-Notice

CMTS deleted unregistered Cable Modem [enet]

Unregistered cable modem deleted to avoid unaccounted bandwidth usage.

ubr7200

"Check modem i/f config for registration bypass " "or errors in tftp config file."

UBR7200-5-UNAUTHSIDTIMEOUT

5-Notice

CMTS deleted BPI unauthorized Cable Modem [enet]

Unauthorized cable modem deleted to enforce CM go through BPI authorization.

ubr7200

"Check modem interface configuration for privacy mandatory " "or errors in tftp configuration file."

UBR7200-5-TEKREQTIMEOUT

5-Notice

CMTS deleted BPI Cable Modem [enet] because traffic not encrypted

Cable modem deleted to force modem to request TEK.

ubr7200

"Check upsteam utilization to ensure bandwidth available for TEK " "request. Noise on the plant can cause this also."

UBR7200-5-EXPIREDBPITIMEOUT

5-Notice

CMTS deleted BPI [chars] expired Cable Modem [enet] with Sid [dec]

Expired cable modem deleted to enforce CM go through BPI authorization.

ubr7200

"Check modem interface configuration for privacy mandatory " "or noise on the plant."

UBR7200-5-BPKMDROPEXCESS

5-Notice

CMTS deleted excessive [chars] Requests Cable Modem [enet] with Sid [dec]

Cable Modem did excessive BPKM requests.

ubr7200

"Check modem interface configuration for privacy mandatory " "or noise on the plant."

UBR7200-5-NOTIMPLMENTEDMNCSMSG

5-Notice

Not implemented DOCSIS MESSAGE received from a Cable Modem\n for interface [chars]

This uBR does not support this type of message. The system may be connected to a non-compliant modem.

ubr7200

"This message is informational only. To be sure there is no problem " "you may contact technical support."

UBR7200-5-NOMULTIPLEUPSTREAMS

5-Notice

Upstream Channel Change not valid for interface [chars]

The software does not support this command for this interface

ubr7200

"Please use this command on a multiple upstream Line card"

UBR7200-3-RP_INVALIDSID_ASSIGN

3-Error

Invalid SID assignment for interface: [chars] CM: [enet]

Invalid SID assignment by RP

ubr7200

"Contact Cisco TAC"

UBR7200-3-NOMORESIDS

3-Error

Maximum number of SIDS have been allocated for interface [chars]: CM [enet]: SID container info: start [dec] end [dec]

The Maxmium number of SIDS has reached

ubr7200

"Assign Cable Modem to another Line Card"

UBR7200-3-TOOMANY_RANGEDSIDS

3-Error

CMTS-HCCP [chars]: Actual Rcvd ranged list sync sids [dec] # of sids saved [dec]

Size of Ranged List Sync Message received.

ubr7200

"Reduce the Number of Cable Modem Sids pre i/f"

UBR7200-3-SIDERRORHCCP

3-Error

Tried to allocate New SID during Failover for interface [chars]: CM [enet]: SID container info: start [dec] end [dec]

Allocate SID during Failover

ubr7200

"Assign Cable Modem to another Line Card"

UBR7200-3-SIDERRORDCC

3-Error

Tried to allocate New SID %D during DCC CM rebuild for interface [chars]: CM [enet]: SID container info: start [dec] end [dec]

Allocate SID during DCC CM rebuild

ubr7200

"Assign Cable Modem to another interface"

UBR7200-4-CM_NP_RF_FAILURE

4-Warning

CM <[enet]> on host interface <[chars]> reported NP RF <[dec]> failure modular-cable <[chars]> CM's NP RFs <[chars]>

CMTS is configured to run script via Embedded Event Manager to handle the Cable Modem NP RF failure.

ubr7200

"Verify that Cable Modem is not experienceing wideband connectivity."

UBR7200-3-NULLMAPPTR

3-Error

Cannot send maps as current_map ptr is NULL\n ds->[hec]current_map->[hec]: [chars]

This is an internal error or may indicate a memory problem.

ubr7200

"Check your available memory. If necessary " "add more memory to the system."

UBR7200-3-I2CERR

3-Error

[chars]

ERROR while accessing the i2c bus

ubr7200

"Error has occured while accessing the internal bus."

UBR7200-3-I2CUPXERR

3-Error

[chars]

ERROR while accessing the Upconverter

ubr7200

"Error occured while accesing the upconverter."

UBR7200-3-SEMCREATEFAIL

3-Error

Unable to create the semaphore

Unable to create the semaphore for non-blocking UPX access

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-SEMLOCKFAIL

3-Error

Unable to lock the semaphore

Unable to lock the semaphore for non-blocking UPX access

ubr7200

"Unable to read the Upconverter status Try again"

UBR7200-3-NOMEM

3-Error

[chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-6-DUAL_CLEANUP_ATTEMPT

6-Information

Second cleanup for modem

A modem entry was attempted to be cleaned up twice

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-NOFORK

3-Error

Could not start Spectrum Management process

An internal software error occurred.

ubr7200

"LOG_STD_SH_TECH_ACTION"

UBR7200-5-AUTHFAIL

5-Notice

Authentication failed for Cable Modem [enet] on interface [chars][chars]

The registration of this modem failed due to an invalid MIC string or use of stale/spoofed tftp config file information by the modem

ubr7200

"Make sure the shared secret in the configuration file " "matches the shared secret configured in the ubr7200. " "If the shared secrets match take action against the modem that is " "possibly spoofing storing and replaying its old config file."

UBR7200-4-CMTS_IPV6_LLA_FAILED_DAD

4-Warning

<133>CMTS[DOCSIS]:<68001301> IPv6 Link-local address has failed DAD. Addr <[enet]>

IPv6 Link-Local has failed DAD.\n

ubr7200

"Check the modem and subscriber"

UBR7200-4-CMTS_IPV6_RX_DHCPV6_WITH_BADADDR

4-Warning

DHCPv6 request received with a bad src IPv6 \naddr. IP <%P> msg <[chars]>

DHCPv6 request received with a bad src IPv6 addr dropping the req\n

ubr7200

"Check the modem and subscriber"

UBR7200-4-CMTS_IPV6_RX_DHCPV6_WITH_MISCONFIG

4-Warning

DHCPv6 reply received \nwith a IPv6 address that does not match the bundle config\nReceived IPv6 address that matches [chars] expected [chars]

DHCPv6 reply received a IPv6 addr that does not match the bundle config dropping the req\n

ubr7200

"Check the bundle config and provisioning system"

UBR7200-4-CMTS_IPV6_RX_DAD_BUT_MDD_ISV4

4-Warning

CMTS ND Proxy code see an NS when CMTS is MDD is v4 only bailing out and not\n accepting this NS message from modem with MAC [enet]

CMTS is not supposed to receive an IPv6 DAD when MDD is set to v4\n

ubr7200

"Check the modem and subscriber"

UBR7200-4-CMTS_IPV6_DROPPING_DHCPV6REQ_FOR_FAIL_IN_LLA_AUTOFIX

4-Warning

Dropping DHCPv6 request \nbecause CMTS has not received NS DAD for link-local address from this \nclient and failed to create a new link-local entry for MAC <[enet]> IPv6 <%P>

\nDropping DHCPv6 request because CMTS has not received NS DAD for link-local address and CMTS failed to add the link-local to client db

ubr7200

"Check the client and subscriber"

UBR7200-4-NUMIPV6ADDR_ERR

4-Warning

DECODE of HCCP TLV for IPV6 has incorrect number of IPv6 addresses = [dec]

\nFailure in encoding of number of IPV6 addrs TLV in HCCPmessage

ubr7200

"Check the clients on the CM for number of IPv6 addresses"

UBR7200-2-NULL_SRC_ERR

2-Critical

HCCP Copy IPv6 addresses has NULL source

\nHCCP IPv6 copy function has been sent NULL src address list.

ubr7200

"Contact Cisco with this log message"

UBR7200-2-CPE_MGMT_IDX_ERR

2-Critical

Index out of range during CPE MGMT data decoding

\nThe index is out of range during CPE MGMT HCCP data decoding.

ubr7200

"Contact Cisco with this log message"

UBR7200-4-REGISTRATION_BEFORE_TFTP_MARK

4-Warning

Registration request unexpected: Cable Modem did not attempt TFTP. Modem marked with #. CM Mac Addr <[enet]>

Registration request unexpected: Cable Modem did not attempt TFTP\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REGISTRATION_BEFORE_TFTP

4-Warning

Registration request unexpected: Cable Modem did not attempt TFTP. Registration Rejected. CM Mac Addr <[enet]>

Registration request unexpected: Cable Modem did not attempt TFTP\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_DS_SELECTION_FAIL

4-Warning

DS Selection failed for Cable Modem [enet] in [chars]

CMTS cannot proceed with handling modem's Registration Request

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_REGISTRATION

4-Warning

Cable modem [enet] on interface [chars] when [chars] attempted re-registration with different QoS

Modem sent a registration request when already registered with a different QoS

ubr7200

"Modem could be attempting theft of service"

UBR7200-4-MTA_REQ_ON_NON_HA_DS

4-Warning

MTA Modem [enet] in [chars] to come online on a non-HA capable DS

CMTS can not move the MTA to a DS that is HA capable after 3 trials

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-CLASSFAIL

5-Notice

Registration failed for Cable Modem [enet] on interface [chars][chars]: [chars]

The registration of this modem failed due to an invalid or unsupported Class of Service setting.

ubr7200

"Make sure the Class of Service fields in the configuration file " "are set correctly."

UBR7200-5-OVERLIMIT

5-Notice

Interface [chars]\n Current total reservation of [dec] bps on Port U[dec] exceeds its\n maximum configured reservation limit of [dec] bps.\n

The currently reserved capacity on the upstream channel\n already exceeds the virtual reservation capacity of that\n upstream channel based on configured subscription level limit.\n

ubr7200

"Need to load balance modems requesting reserved upstream rate on\n" "some other upstream channel or increase the subscription level\n" "limit on current upstream channel at increasing risk of not being\n" "able to guarantee the individual reserved rates for modems if this\n" "upstream channel is already oversubscribed beyond raw capacity\n"

UBR7200-5-TRAFSHAPNOCREAT

5-Notice

Unable to create downstream traffic shaping queues

A possible memory error has occurred which is preventing the software from creating downstream traffic shapping queues.

ubr7200

"Gather information about running configuration and amount of memory " "in the system and report it to your technical support representative."

UBR7200-5-TRAFSHAPPROCFAIL

5-Notice

Unable to fork downstream shaper process

A possible memory error has occurred which is preventing the software from creating the downstream shaper process.

ubr7200

"Gather information about running configuration and amount of memory " "in the system and report it to your technical support representative."

UBR7200-5-TRAFSHAPBADTIMER

5-Notice

Bad timer expiry in downstream traffic shaper process Timer [hec]

An unknown downstream traffic shaper timer has expired.

ubr7200

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200-6-CMMOVED

6-Information

Cable modem [enet] has been moved from interface [chars] to interface [chars].

The cable modem has been detected ranging on a new interface.

ubr7200

"Informational only"

UBR7200-6-USPRIMARYSFIDCONFLICT

6-Information

Assigned us primary sfid [dec] conflicts with existing us primary sfid [dec] for Cable modem [enet] on interface [chars]

The assigned upstream primary SFID conflicts with the existing upstream primary SFID for the cable modem.

ubr7200

"Informational only"

UBR7200-6-DSPRIMARYSFIDCONFLICT

6-Information

Assigned ds primary sfid [dec] conflicts with existing ds primary sfid [dec] for Cable modem [enet] on interface [chars]

The assigned downstream primary SFID conflicts with the existing downstream primary SFID for the cable modem.

ubr7200

"Informational only"

UBR7200-6-FECKBYTEADJUST

6-Information

[chars] burst's FEC K BYTE in mod profile [dec] is adjusted to [dec] bytes.

The FEC K bytes in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-DIFFENCADJUST

6-Information

Differential-encoding is disabled on interface [chars] upstream [chars] it is only supported for QPSK or QAM16.

Differential-encoding is only supported for QPSK or QAM16.

ubr7200

"Informational only"

UBR7200-6-LCHDIFFENCADJUST

6-Information

Differential-encoding is disabled on interface [chars] upstream [chars] it should be supported by all active logical channels.

Differential-encoding should be supported on all logical channels.

ubr7200

"Informational only"

UBR7200-6-PREAMLENADJUST

6-Information

[chars] burst's preamble length in mod profile [dec] is adjusted to [dec] bits.

The preamble length in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-PREAMLENCHECK

6-Information

preamble length exceeds total of 128 byte.

The preamble length exceeds total of 128 byte.

ubr7200

"Informational only"

UBR7200-6-GUARDSYMLENADJUST

6-Information

[chars] burst's guard symbol length in mod profile [dec] is adjusted to [dec] symbols.

The guard symbol length in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-RSINTRLVBLKSIZEADJUST

6-Information

[chars] burst's RS interleave block size in mod profile [dec] is adjusted to [dec] bytes.

The RS interleave block size in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-RSINTRLVDEPTHADJUST

6-Information

[chars] burst's RS interleave depth in mod profile [dec] is adjusted to [dec].

The RS interleave depth in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-RSINTRLVDISABLED

6-Information

[chars] burst's RS interleaver in mod profile [dec] is auto disabled.

The RS interleaver in the burst profile is auto disabled.

ubr7200

"Informational only"

UBR7200-4-DUPLICATEMAC

4-Warning

Cable modem [enet] is online on both interface [chars] and interface [chars].

The cable modem has been detected on two interfaces.

ubr7200

"Check for cable modems with duplicate MAC addresses."

UBR7200-4-SIDWITHOUTCM

4-Warning

SID [dec] not bound to any CM.

This SID does not have a valid CM database pointer

ubr7200

"For Informational Purposes Only"

UBR7200-4-CMNOPRIMSF

4-Warning

CM [enet] does not have any primary service flows

This CM has no primary service flows

ubr7200

"For Informational Purposes Only"

UBR7200-6-ACTIVE

6-Information

Cable clock [chars] reference active

The clock reference became active

ubr7200

"Informational only"

UBR7200-6-LOS

6-Information

Cable clock [chars] reference Loss of Signal

The clock reference was lost

ubr7200

"Check reference source"

UBR7200-6-HOLDOVER

6-Information

Cable clock in Holdover mode

Clockcard switched to holdover mode

ubr7200

"Check reference source"

UBR7200-6-FREERUN

6-Information

Cable clock in Freerun mode

Clockcard is in free run mode

ubr7200

"Informational only"

UBR7200-6-REFLOCK

6-Information

Cable clock locked to [chars] reference

Clockcard locked onto clock source

ubr7200

"Informational only"

UBR7200-6-SRCMP

6-Information

Cable Clock primary reference is midplane TDM clock

Clockcard primary reference is from midplane TDM clock

ubr7200

"Informational only"

UBR7200-6-DRVMP

6-Information

Midplane TDM clock reference defaults to Clockcard

Clockcard primary reference is from midplane TDM clock

ubr7200

"Informational only"

UBR7200-4-CLK_HWFAULT

4-Warning

Hardware Fault in Clockcard

Hardware fault in Clockcard

ubr7200

"Replace clock card"

UBR7200-4-BADTXOFFSET

4-Warning

Bad timing offset %ld detected for cable modem [enet] sid [hec] cm status [hec] dcc [chars] skip_reg [chars].

The cable modem is not using the correct starting offset during initial ranging. This causes a zero negative timing offset to be recorded by the CMTS for this modem. The CMTS internal algorithms that rely on the

ubr7200

"Locate the cable modem based on MAC address and report initial " "timing offset problem to the CM vendor"

UBR7200-6-MAP_UPSTREAM_BW_ALLOCATION

6-Information

<135>CMTS[DOCSIS]:<77000100> A transmit opportunity was missed because MAP arrived too late

A transmit opportunity was missed because MAP arrived too late \n

ubr7200

"If the problem persists with a particular cable modem " "reboot the cable modem and check for possible hardware or" "software problems with that cable modem If this problem " "occurs with many cable modemscheck the cable plant for " "RF transmission and noise ingress problems."

UBR7200-4-NO_RANGING_REQUESTS

4-Warning

<133>CMTS[DOCSIS]:<82010100> No Ranging Requests received from POLLED CM Mac Addr <[enet]> CMTS generated polls

No Ranging Requests received from POLLED CM CMTS generated polls\n

ubr7200

"Please look for possible noise or other RF plant " "problems on the upstream channel"

UBR7200-4-RETRIES_EXHAUSTED_POLL_CM

4-Warning

<133>CMTS[DOCSIS]:<82010200> Retries exhausted for polled CM Mac Addr <[enet]>. After 16 R101.0 errors.

Retries exhausted for polled CM . After 16 R101.0 errors.Note: this is different from R102.0 in that it was able to try i.e. got REQ's but failed to Range properly.\n

ubr7200

"Please look for possible noise or other RF plant " "problems on the upstream channel"

UBR7200-4-UNABLE_TO_RANGE_CM

4-Warning

<133>CMTS[DOCSIS]:<82010300> Unable to Successfully Range CM Mac Addr <[enet]>. Retries Exhausted.

Unable to Successfully Range CM Retries Exhausted.\n

ubr7200

"CM reinitialize its MAC interface and attempt to reregister." " check the cable plant for potentialnoise or other RF problems" " Check the configuration of the cable interface on the CMTS " " that is servicing this cable modem to ensure that the interface" " is enabled and properly configured"

UBR7200-4-NO_RNG_REQ_TIMEOUT_SID

4-Warning

<133>CMTS[DOCSIS]:<82010400> Failed to receive Periodic RNG-REQ from modem [chars] timing-out SID

Failed to receive Periodic RNG-REQ from modem SID X timing-out SID\n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-SERVICE_UNAVAIL_OTHER

4-Warning

<133>CMTS[DOCSIS]:<73000400> Service unavailable - Other. CM Mac Addr <[enet]>

Registration Failed :Service Unavailable \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73000401> Service unavailable - Unrecognized configuration setting. CM Mac Addr <[enet]>

Registration Failed Unrecognized Configuration Setting\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SERVICE_TEMPORARILY_UNAVAILABLE

4-Warning

<133>CMTS[DOCSIS]:<73000402> Service unavailable - Temporarily unavailable. CM Mac Addr <[enet]>

Registration Failed Service temporarily not available \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SERVICE_PERMANENTLY_UNAVAILABLE

4-Warning

<133>CMTS[DOCSIS]:<73000403> Service unavailable - Permanent. CM Mac Addr <[enet]>

Service Permanently unavailable\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REJ_AUTH_FAIL_CMTS_MIC_INVALID

4-Warning

<133>CMTS[DOCSIS]:<73000500> Registration rejected authentication failure: CMTS MIC invalid. CM Mac Addr <[enet]>

Registration rejected authentication failure: CMTS MIC invalid\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REJ_AUTH_FAIL_TLV_PARAMS_MISMATCH

4-Warning

<133>CMTS[DOCSIS]:<73000501>Registration authentication failure: REG REQ rejected TLV parameters do not match learned config file TLV parameters. CM Mac Addr <[enet]>

REG REQ TLV parameters do not match learned config fileTLV parameters\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_INVALID_MAC_HEADER

4-Warning

<133>CMTS[DOCSIS]:<73010100> REG REQ has Invalid MAC header. CM Mac Addr <[enet]>

REG REQ has Invalid MAC header \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_SID

4-Warning

<133>CMTS[DOCSIS]:<73010200> REG REQ has Invalid SID or not in use. CM Mac Addr <[enet]>

REG REQ has Invalid SID or not in use\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REQUIRED_TLV_ABSENT

4-Warning

<133>CMTS[DOCSIS]:<73010400> REG REQ missed Required TLV's. CM Mac Addr <[enet]>

REG REQ missed Required TLV's \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DOWNSTREAM_FREQUENCY_FORMAT_INVALID

4-Warning

<133>CMTS[DOCSIS]:<73010500> Bad DS FREQ - Format Invalid. CM Mac Addr <[enet]>

REG REQ : Bad DS FREQ - Format Invalid .\n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DOWNSTREAM_FREQUENCY_NOT_IN_USE

4-Warning

<133>CMTS[DOCSIS]:<73010501> Bad DS FREQ - Not in use. CM Mac Addr <[enet]>

REG REQ : Bad DS FREQ - Not in use.\n

ubr7200

"Please Check the Config File Frequency"

UBR7200-4-DOWNSTREAM_FREQUENCY_NOT_MULTIPLE_OF_62500

4-Warning

<133>CMTS[DOCSIS]:<73010502> Bad DS FREQ - Not multiple of 62500. CM Mac Addr <[enet]>

REG REQ : Bad DS FREQ - Not multiple of 62500.\n

ubr7200

"Please Check the Config File Frequency"

UBR7200-4-INVALID_UNASSIGNED_UPSTREAM_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<73010600> Bad US CH - Invalid or Unassigned. CM Mac Addr <[enet]>

REG REQ : Bad US CH - Invalid or Unassigned.\n

ubr7200

"Please Check the upstream Channel Frequency"

UBR7200-4-UPSTREAM_CHANNEL_CHANGE_WITH_REG_REQ

4-Warning

<133>CMTS[DOCSIS]:<73010601> Bad US CH -Change followed with RE- Registration REQ. CM Mac Addr <[enet]>

REG REQ : Bad US CH -Change followed with RE- Registration REQ .\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_UPSTREAM_CHANNEL_OVERLOAD

4-Warning

<133>CMTS[DOCSIS]:<73010700> Bad US CH -Overload. CM Mac Addr <[enet]>

REG REQ : Bad US CH -Overload.\n

ubr7200

"Check the Upstream Frequency"

UBR7200-4-BAD_NETWORK_ACCESS_CONFIGURATION

4-Warning

<133>CMTS[DOCSIS]:<73010800> Network Access has Invalid Parameter. CM Mac Addr <[enet]>

REG REQ : Network Access has Invalid Parameter.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_COS_CONFIGURATION

4-Warning

<133>CMTS[DOCSIS]:<73010900> Bad Class of Service- Invalid Configuration. CM Mac Addr <[enet]>

Registration Failed Bad Class of Service\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-COS_UNSUPPORTED_CLASS

4-Warning

<133>CMTS[DOCSIS]:<73011000> Bad Class of Service- Unsupported class. CM Mac Addr <[enet]>

Registration Failed Bad Class of Service-Unsupported class\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-COS_INVALID_ID_OUT_OF_RANGE

4-Warning

<133>CMTS[DOCSIS]:<73011100> Bad Class of Service. Invalid Class ID or out of range. CM Mac Addr <[enet]>

Bad Class of Service. Invalid Class ID or out of range.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_MAX_DOWNSTREAM_BIT_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011200> Bad Max DS bit - Invalid format. CM Mac Addr <[enet]>

Registration Failed Bad Max Downstream bit has invalid format.\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_MAX_DOWNSTREAM_BITRATE_UNSUPPORTED_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73011201> Bad Max DS Bit Rate Unsupported Setting. CM Mac Addr <[enet]>

REG REQ : Bad Max DS Bit Rate Unsupported Setting.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_MAX_UPSTREAM_BIT_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011300> Bad Max US Bit - Invalid format. CM Mac Addr <[enet]>

Registration Failed Bad Max Upstream bit Rate has invalid format.\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_MAX_UPSTREAM_BITRATE_UNSUPPORTED_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73011301> Bad Max US Bit Rate - Unsupported Setting. CM Mac Addr <[enet]>

REG REQ : Bad Max US Bit Rate - Unsupported Setting.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_UPSTREAM_PRIORITY_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011400> Bad US Priority Configuration - Invalid format. CM Mac Addr <[enet]>

Registration Failed Upstream Priority Format has invalid format.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OUT_OF_RANGE_US_PRIORITY_CONFIGURATION

4-Warning

<133>CMTS[DOCSIS]:<73011401> Bad US Priority Configuration - Setting out of Range. CM Mac Addr <[enet]>

Out of Range US Traffic Priority Value.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_MIN_UPSTREAM_CHANNEL_BIT_RATE_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011500> Bad Guaranteed MIN US Channel bit Rate Configuration setting - Invalid format. CM Mac Addr <[enet]>

Guaranteed Minimum Upstream Rate format invalid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-MIN_UPSTREAM_CHANNEL_BIT_RATE_EXCEEDS_MAX

4-Warning

<133>CMTS[DOCSIS]:<73011501> Bad Guaranteed Min US Channel Bit Rate Configuration setting - Exceed Max US Bit Rate. CM Mac Addr <[enet]>

CM MIN Upstream Channel Bit Rate exceeds maximum value.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-MIN_UPSTREAM_CHANNEL_BITRATE_OUT_OF_RANGE

4-Warning

<133>CMTS[DOCSIS]:<73011502> Bad Guaranteed Min US CH Bit rate Configuration setting - Out of Range. CM Mac Addr <[enet]>

REG REQ : Bad Guaranteed Min US CH Bit rate Configuration setting - Out of Range.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_MAX_UPSTREAM_BURST_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011600> Bad Max US CH Transmit Burst Configuration setting - Invalid format. CM Mac Addr <[enet]>

CM Max US channel transmit burst type invalid format.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OUT_OF_RANGE_MAX_UPSTREAM_BURST

4-Warning

<133>CMTS[DOCSIS]:<73011601> Bad Max US CH Transmit Burst Configuration setting - Out of Range. CM Mac Addr <[enet]>

CM Max US channel transmit burst setting out of range.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_MODEM_CONFIGURATION_SETTING_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011700> Invalid Modem Capabilities configuration setting . CM Mac Addr <[enet]>

CM Capabilities config value contains an invalid format.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OUT_OF_RANGE_CONFIG_FILE_PARAMETERS

4-Warning

<133>CMTS[DOCSIS]:<73011800> Configuration file contains parameter with the value outside of the range. CM Mac Addr <[enet]>

CM config file parameter contains an out of range parameter.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<73020100> REG REQ rejected Unspecified Reason . CM Mac Addr <[enet]>

Unspecified Reason \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73020101> REG REQ rejected - Unrecognized configuration setting. CM Mac Addr <[enet]>

REG REQ rejected - Unrecognized configuration setting . \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_TEMPORARY_NO_RESOURCE

4-Warning

<133>CMTS[DOCSIS]:<73020102> REG REQ rejected - temporary no resource . CM Mac Addr <[enet]>

REG REQ rejected - temporary no resource . \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_PERMANENT_ADMINISTRATIVE

4-Warning

<133>CMTS[DOCSIS]:<73020103> REG REQ rejected - Permanent administrative . CM Mac Addr <[enet]>

REG REQ rejected - Permanent administrative. \n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<73020104> REG REQ rejected Required parameter not present. CM Mac Addr <[enet]>

Required parameter not present\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-HEADER_SUPPRESSION_SETTING_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<73020105> REG REQ rejected Header suppression setting not supported. CM Mac Addr <[enet]>

Header suppression setting not supported\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<73020106> REG REQ rejected - Multiple errors. CM Mac Addr <[enet]>

CM Registration Request msg contains multile errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<73020107> REG REQ rejected duplicate reference-ID or index in message . CM Mac Addr <[enet]>

CM Registration Request message contains a duplicate ID or index.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_PARAM_INVALID

4-Warning

<133>CMTS[DOCSIS]:<73020108> REG REQ rejected parameter invalid for context. CM Mac Addr <[enet]>

CM Registration Request conatins a invalide parameter for context.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_AUTH_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<73020109> REG REQ rejected - Authorization failure . CM Mac Addr <[enet]>

CM Registration Request Authorization failure.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020110> REG REQ rejected - Major service flow error . CM Mac Addr <[enet]>

CM Registration Request service flow error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_CLASSIFIER_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020111> REG REQ rejected - Major classifier error . CM Mac Addr <[enet]>

CM Registration Request classifier error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020112> REG REQ rejected - Major PHS rule error . CM Mac Addr <[enet]>

CM Registration Request PHS rule error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<73020113> REG REQ rejected - Multiple major errors. CM Mac Addr <[enet]>

CM Registration Request mulitiple errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020114> REG REQ rejected - Message syntax error . CM Mac Addr <[enet]>

CM Registration Request syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_PRIM_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020115> REG REQ rejected - Primary service flow error. CM Mac Addr <[enet]>

CM Registration Request primary service flow error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<73020116> REG REQ rejected - Message too big. CM Mac Addr <[enet]>

CM Registration Request message to large.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REGISTRATION_ABORT_NO_REG_ACK

4-Warning

<133>CMTS[DOCSIS]:<73030100> REG aborted no REG-ACK. CM Mac Addr <[enet]>

CM Reg aborted. No CM REG_ACK message.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_ACK_REJ_UNSPECIFIED

4-Warning

<133>CMTS[DOCSIS]:<73030200> REG ACK rejected unspecified reason. CM Mac Addr <[enet]>

CM Reg Ack message rejected.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_ACK_REJ_BAD_RCC

4-Warning

<133>CMTS[DOCSIS]:<73030208> REG ACK rejected bad rcc. CM Mac Addr <[enet]>

CM Reg Ack message bad rcc.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_ACK_REJ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73030300> REG ACK rejected message syntax error. CM Mac Addr <[enet]>

CM Reg Ack message syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<83000100> Service Add rejected - Unspecified reason. CM Mac Addr <[enet]>

Unspecified reason \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83000101> Service Add rejected - Unrecognized Configuration Setting. CM Mac Addr <[enet]>

Unrecognized Configuration Setting \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_TEMP_NO_RESOURCE

4-Warning

<133>CMTS[DOCSIS]:<83000102> Service Add rejected - Temporary no resource. CM Mac Addr <[enet]> [chars]

CM DSA message rejected due to no rousources.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_PERMANENT_ADMINISTRATIVE

4-Warning

<133>CMTS[DOCSIS]:<83000103> Service Add rejected - Permanent Administrative. CM Mac Addr <[enet]> [chars]

Permanent Administrative \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83000104> Service Add rejected - Required parameter not present. CM Mac Addr <[enet]>

Required parameter not present\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_HEADER_SUPPR_SETTING_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<83000105> Service Add rejected - Header suppression setting not supported . CM Mac Addr <[enet]>

Header suppression setting not supported\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_SERVICE_FLOW_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000106> Service Add rejected Service flow exists . CM Mac Addr <[enet]>

CM DSA rejected. Service flow exists.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_HMAC_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000101> Service Add rejected - HMAC Authentication Failure. CM Mac Addr <[enet]>

HMAC Authentication Failure \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_ADD_ABORTED

4-Warning

<133>CMTS[DOCSIS]:<83000108> Service Add rejected - Add aborted. CM Mac Addr <[enet]>

CM DSA msg rejected.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000109> Service Add rejected - Multiple errors. CM Mac Addr <[enet]>

CM DSA rejected due to multilpe errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_CLASSIFIER_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000110> Service Add rejected - Classifier not found. CM Mac Addr <[enet]>

CM DSA rejected due to classifier not found.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_CLASSIFIER_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000111> Service Add rejected - Classifier exists. CM Mac Addr <[enet]>

CM DSA rejected due to classifier already exists.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_PHS_RULE_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000112> Service Add rejected - PHS rule not found . CM Mac Addr <[enet]>

CM DSA rejected because the PHS rule was not found.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000113> Service Add rejected - PHS rule exists. CM Mac Addr <[enet]>

CM DSA rejected because the PHS rule already exists.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<83000114> Service Add rejected duplicate reference-ID or index in message . CM Mac Addr <[enet]>

CM DSA rejected because duplicate ref ID or index.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MULTIPLE_UPSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000115> Service Add rejected - Multiple upstream flow . CM Mac Addr <[enet]>

CM DSA rejected because muliptle US flows.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MULTIPLE_DOWNSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000116> Service Add rejected - Multiple downstream flow . CM Mac Addr <[enet]>

CM DSA rejected because mulitple DS flows.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_CLASSIFIER_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000117> Service Add rejected - Classifier for another flow . CM Mac Addr <[enet]>

CM DSA rejected because classifier is for another flow.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_PHS_RULE_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000118> Service Add rejected - PHS rule for another flow . CM Mac Addr <[enet]>

CM DSA rejected becasue PHS rule if for another flow.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83000119> Service Add rejected - Parameter invalid for context. CM Mac Addr <[enet]>

CM DSA rejected because a parameter is invalid for the context.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_AUTH_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000120> Service Add rejected - Authorization failure. CM Mac Addr <[enet]>

CM DSA rejected because of an authorization failure.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000121> Service Add rejected - Major service flow error. CM Mac Addr <[enet]>

CM DSA rejected becasue of a major service flow error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_CLASSIFIER_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000122> Service Add rejected - Major classifier error. CM Mac Addr <[enet]>

CM DSA rejected because of a major classifier error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000123> Service Add rejected - Major PHS rule error. CM Mac Addr <[enet]>

CM DSA rejected because of a major PHS rule error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000124> Service Add rejected - Multiple major errors. CM Mac Addr <[enet]>

CM DSA rejected because of multiple major errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000125> Service Add rejected - Message syntax error. CM Mac Addr <[enet]>

CM DSA rejected because of a message syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83000126> Service Add rejected - Message too big. CM Mac Addr <[enet]>

CM DSA rejected becasue the msg was to big.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_TEMP_DCC

4-Warning

<133>CMTS[DOCSIS]:<83000127> Service Add rejected - Temporary DCC . CM Mac Addr <[enet]>

CM DSA rejected due to a tmp DCC.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<83000200> Service Change rejected - Unspecified reason. CM Mac Addr <[enet]>

Unspecified reason \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83000201> Service Change Rejected - Unrecognized Configuration Setting. CM Mac Addr <[enet]>

Unrecognized Configuration Setting \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_TEMP_NO_RESOURCE

4-Warning

<133>CMTS[DOCSIS]:<83000202> Service Change rejected - Temporary no resource. CM Mac Addr <[enet]> [chars]

CM DSC rejected due to no resource.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_PERMANENT_ADMINISTRATIVE

4-Warning

<133>CMTS[DOCSIS]:<83000203> Service Change rejected - Permanent Administrative. CM Mac Addr <[enet]> [chars]

Permanent Administrative \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_REQUESTOR_NOT_OWNER

4-Warning

<133>CMTS[DOCSIS]:<83000204> Service Change rejected - Requestor Not Owner Of Service Flow . CM Mac Addr <[enet]>

Requestor Not Owner Of Service Flow\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83000206> Service Change rejected - Required parameter not present. CM Mac Addr <[enet]>

Required parameter not present\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_SERVICE_FLOW_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000205> Service Change rejected - Service Flow Not Found. CM Mac Addr <[enet]>

Service Flow Not Found\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_HEADER_SUPPR_SETTING_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<83000207> Service Change rejected - Header suppression setting not supported . CM Mac Addr <[enet]>

Header suppression setting not supported\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_HMAC_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000208> Service Change rejected - HMAC Auth Failure. CM Mac Addr <[enet]>

HMAC Authentication Failure \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000209> Service Change rejected - Multiple errors . CM Mac Addr <[enet]>

CM DSC rejected because of mulitple errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_CLASSIFIER_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000210> Service Change rejected - Classifier not found. CM Mac Addr <[enet]>

CM DSC rejected because of classifier not found.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_CLASSIFIER_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000211> Service Change rejected - Classifier exists. CM Mac Addr <[enet]>

CM DSC rejected because classifier exists.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_PHS_RULE_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000212> Service Change rejected - PHS rule not found . CM Mac Addr <[enet]>

CM DSC rejected because PHS rule not found.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000213> Service Change rejected - PHS rule exists. CM Mac Addr <[enet]>

CM DSC rejected because PHS rule exists.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<83000214> Service Change rejected - Duplicate reference-ID or index in message . CM Mac Addr <[enet]>

CM DSC rejected because duplicate ref ID or index.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MULTIPLE_UPSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000215> Service Change rejected - Multiple upstream flow . CM Mac Addr <[enet]>

CM DSC rejected because multiple US flows.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MULTIPLE_DOWNSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000216> Service Change rejected - Multiple downstream flow . CM Mac Addr <[enet]>

CM DSC rejected because mulitple DS flows.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_CLASSIFIER_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000217> Service Change rejected - Classifier for another flow . CM Mac Addr <[enet]>

CM DSC rejected because classifier is for another flow.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_PHS_RULE_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000218> Service Change rejected - PHS rule for another flow . CM Mac Addr <[enet]>

CM DSC rejected because PHS rule is for another flow.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83000219> Service Change rejected - Parameter invalid for context. CM Mac Addr <[enet]>

CM DSC rejected because parameter invalid for context.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_AUTH_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000220> Service Change rejected - Authorization failure. CM Mac Addr <[enet]>

CM DSC rejected because authorizatio failure.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000221> Service Change rejected - Major service flow error. CM Mac Addr <[enet]>

CM DSC rejected because service flow error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_CLASSIFIER_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000222> Service Change rejected - Major classifier error. CM Mac Addr <[enet]>

CM DSC rejected because classifier error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000223> Service Change rejected - Major PHS rule error. CM Mac Addr <[enet]>

CM DSC rejected because PHS rule error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000224> Service Change rejected - Multiple major errors. CM Mac Addr <[enet]>

CM DSC rejected because mulitple errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000225> Service Change rejected - Message syntax error. CM Mac Addr <[enet]>

CM DSC rejected because message syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83000226> Service Change rejected - Message too big. CM Mac Addr <[enet]>

CM DSC rejected because message to big.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_TEMP_DCC

4-Warning

<133>CMTS[DOCSIS]:<83000227> Service Change rejected - Temporary DCC . CM Mac Addr <[enet]>

CM DSC rejected because temp dcc.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSD_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<83000300> Service Delete rejected - Unspecified reason . CM Mac Addr <[enet]>

Unspecified reason \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSD_REQUESTOR_NOT_OWNER

4-Warning

<133>CMTS[DOCSIS]:<83000301> Service Delete rejected - Requestor Not Owner of service flow. CM Mac Addr <[enet]>

Requestor Not Owner\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSD_SERVICE_FLOW_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000302> Service Delete rejected - Service Flow Not Found. CM Mac Addr <[enet]>

Service Flow Not Found\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSD_HMAC_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000303> Service Delete rejected - HMAC Auth Failure. CM Mac Addr <[enet]>

HMAC Authentication Failure \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSD_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000304> Service Delete rejected - Message Syntax Error. CM Mac Addr <[enet]>

CM DSD rejected becuase of message syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_ACK_REJECTED_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83020100> Service Add Response rejected - Invalid transaction ID. CM Mac Addr <[enet]>

ACK Rejected invalid transaction ID \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_ACK_REJECTED_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83020200> Service Change ACK Rejected - Invalid transaction ID. CM Mac Addr <[enet]>

ACK Rejected invalid transaction ID \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_ABORTED_NO_ACK

4-Warning

<133>CMTS[DOCSIS]:<83020101> Service Add Aborted - No ACK. CM Mac Addr <[enet]>

DSX Aborted No ACK \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_ABORTED_NO_ACK

4-Warning

<133>CMTS[DOCSIS]:<83020201> Service Change Aborted - No ACK. CM Mac Addr <[enet]>

DSX Aborted No ACK \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83010100> Service Add response rejected - Invalid Transaction ID . CM Mac Addr <[enet]>

CM DSA response is rejected because of invalid transation ID.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_ABORTED_NO_RSP

4-Warning

<133>CMTS[DOCSIS]:<83010101> Service Add aborted - No RSP . CM Mac Addr <[enet]>

CM DSA aborted. No response.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_ABORTED_NO_RSP

4-Warning

<133>CMTS[DOCSIS]:<83010201> Service Change aborted - No RSP . CM Mac Addr <[enet]>

CM DSC aborted due to no response.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83010200> Service Change response rejected - Invalid Transaction ID . CM Mac Addr <[enet]>

CM DSC response rejected because of an invalid transation ID.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_AUTHORIZATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83010202> Service Change Response rejected - HMAC Auth failure. CM Mac Addr <[enet]>

CM DSA RSP rejected because of an authorization failure.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83010205> Service Change Response rejected - Unrecognized configuration setting. CM Mac Addr <[enet]>

CM DSC RSP reject because of unrecognized configuration setting.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_REQD_PARAM_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83010206> Service Change Response rejected - Required parameter not present. CM Mac Addr <[enet]>

CM DSC RSP is rejected because the required parameter is not present.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83010209> Service Change Response rejected - PHS rule exists. CM Mac Addr <[enet]>

CM DSC RSP rejected because of a major PHS rule error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_DUPLC_REF_ID_OR_INDEX

4-Warning

<133>CMTS[DOCSIS]:<83010210>Service Change Response rejected - Duplicated reference-ID or index in message. CM Mac Addr <[enet]>

CM DSC RSP rejected because duplicate ref ID or index.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83010211> Service Change Response rejected - Invalid parameter for context. CM Mac Addr <[enet]>

CM DSC RSP rejected because of invalid parameter for context.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MAJOR_CFR_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010212> Service Change Response rejected - Major classifier error. CM Mac Addr <[enet]>

CM DSC RSP rejected because of a major classifier error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010213> Service Change Response rejected - Major PHS rule error. CM Mac Addr <[enet]>

CM DSC RSP is rejected because of a major PHS error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83010215> Service Change Response rejected - Message too big. CM Mac Addr <[enet]>

CM DSC RSP rejected becasue the msg was to big.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010203> Service Change Response rejected - Message syntax error. CM Mac Addr <[enet]>

CM DSC RSP rejected because of a message syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSD_RSP_REJECTED_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83010300> Service Delete Response rejected - Invalid transaction ID. CM Mac Addr <[enet]>

DSD Response rejectedinvalid transaction ID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83010105> Service Add Response rejected - Unrecognized configuration setting. CM Mac Addr <[enet]>

CM DSA RSP is rejected because of unrecognized configuration setting.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_REQD_PARAM_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83010106> Service Add Response rejected - Required parameter not present. CM Mac Addr <[enet]>

CM DSA RSP is rejected because the required parameter is not present.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83010110> Service Add Response rejected - PHS rule exists. CM Mac Addr <[enet]>

CM DSA is rejected because the PHS rule already exists.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_PARAM_INVALID_FOR_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83010113> Service Add Response rejected - Parameter invalid for context. CM Mac Addr <[enet]>

CM DSA RSP rejected because a parameter is invalid for the context

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_MAJOR_CFR_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010115> Service Add Response rejected - Major classifier error. CM Mac Addr <[enet]>

CM DSA RSP rejected because of a major classifier error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010116> Service Add Response rejected - Major PHS Rule error. CM Mac Addr <[enet]>

CM DSA RSP rejected because of a major PHS rule error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83010118> Service Add Response rejected - Message too big. CM Mac Addr <[enet]>

CM DSA RSP rejected becasue the msg was to big.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSX_RESTORE_INVALID_CFRID

4-Warning

DSX restore cfr state found invalid cfrid. CM Mac Addr <[enet]>

DSX restore cfr state found invalid cfrid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSX_RESTORE_CFR_STATE_FAILED

4-Warning

DSX restore cfr state fail. Attempted to restore state. CM Mac Addr <[enet]>

DSX restore cfr state fail.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MISSING_BP_CONFIGURATION_SETTING_TLV

3-Error

<132>CMTS[DOCSIS]:<66010100> Missing BP Configuration Setting TLV. TLV Type <[enet]>

Missing BP Configuration Setting TLV \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-INVALID_BP_CONFIGURATION_SETTING_VALUE

3-Error

<132>CMTS[DOCSIS]:<66010200> Invalid BP Configuration Setting Value for TLV type [dec]. CM MAC Addr <[enet]>

Invalid BP Configuration Setting Value \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-EXCESSIVE_SAV_GROUP_IDS

5-Notice

More than 1 SAV Group ID in registration request for CM MAC <[enet]>. Ignoring the excessive group ids

There may be more than 1 SAV Group IDs specified in the in the configuration file\n

ubr7200

"Please inspect the configuration file"

UBR7200-5-EXCESSIVE_SAV_PREFIXES

5-Notice

More than [dec] SAV prefixes in the registration request for CM MAC <[enet]>. Ignoring the excessive prefixes

There are excessive number of SAV prefixes in the configuration file\n

ubr7200

"Please inspect the configuration file"

UBR7200-5-MALFORMED_MODEM_TLV

5-Notice

PARSER-ERR: Next TLV type=[dec] steps beyond end of TLV block.\n\t

Malformed TLV found in parsing\n

ubr7200

"Please check if the modem's behavior is correct"

UBR7200-3-CM_CERTIFICATE_FORMAT_ERROR

3-Error

<133>CMTS[DOCSIS]: CM Certificate Format Error

CM Certificate Format Error \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MANUFACTURE_CA_CM_CERTIFICATE_FORMAT_ERROR

3-Error

<133>CMTS[DOCSIS]: CM MAC Addr <[enet]> on Interface [chars] U[dec] : [chars]

Manufacture CA Certificate Format Error \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-CM_CERTIFICATE_SELF_VERFICATION_ERROR

3-Error

<133>CMTS[DOCSIS]:<0> CM Certificate Self-Verfication Error

CM Certificate Self-Verfication Error \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BPI_UNINITIALIZED

3-Error

<133>CMTS[DOCSIS]:<0> BPI has not yet initialized

The root certificates and crypto library is being initialized. CM Mac Addr <[enet]>\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66030102> Auth Reject - No Information . CM Mac Addr <[enet]>

Auth Reject No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_UNAUTHORIZED_CM

3-Error

<132>CMTS[DOCSIS]:<66030103> Auth Reject - Unauthorized CM . CM Mac Addr <[enet]>

Auth Reject Unauthorized CM\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_UNAUTHORIZED_SAID

3-Error

<132>CMTS[DOCSIS]:<66030104> Auth Reject - Unauthorized SAID. CM Mac Addr <[enet]>

Auth Reject Unauthorized SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_PERMANENT_AUTHORIZATION_FAILURE

3-Error

<132>CMTS[DOCSIS]:<66030108> Auth Reject - Permanent Authorization Failure . CM Mac Addr <[enet]>

Auth Reject Permanent Authorization Failure\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_TOD_NOT_ACQUIRED

3-Error

<132>CMTS[DOCSIS]:<66030109> Auth Reject - Time of Day not acquired . CM Mac Addr <[enet]>

CM Auth Rejected. TOD not acquired.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-CM_CERTIFICATE_ERROR

3-Error

<132>CMTS[DOCSIS]:<66030111> CM Certificate Error. CM Mac Addr <[enet]>

CM Certificate error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66030202> Auth Invalid - No Information. CM Mac Addr <[enet]>

Auth Invalid No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_UNAUTHORIZED_CM

3-Error

<132>CMTS[DOCSIS]:<66030203> Auth Invalid - Unauthorized CM. CM Mac Addr <[enet]>

Auth Invalid Unauthorized CM\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_UNSOLICITED

3-Error

<132>CMTS[DOCSIS]:<66030205> Auth Invalid - Unsolicited. CM Mac Addr <[enet]>

Auth Invalid Unsolicited\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_INVALID_KEY_SEQUENCE_NUMBER

3-Error

<132>CMTS[DOCSIS]:<66030206> Auth Invalid - Invalid Key Sequence Number. CM Mac Addr <[enet]>

Auth Invalid-Invalid Key Sequence Number\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_MESSAGE_AUTHENTICATION_FAILURE

3-Error

<132>CMTS[DOCSIS]:<66030207> Auth Invalid - MessageKey Request Authentication Failure . CM Mac Addr <[enet]>

Auth Invalid Message Authentication Failure\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-UNSUPPORTED_CRYPTO_SUITE

3-Error

<132>CMTS[DOCSIS]:<66030300> Unsupported Crypto Suite. CM Mac Addr <[enet]>

Unsupported Crypto Suite\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-CRL_NOT_RESPONDING

4-Warning

<132>CMTS[DOCSIS]:<66030400> Failed to retrieve CRL from [chars]

CRL not available\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OCSP_NOT_RESPONDING

4-Warning

<132>CMTS[DOCSIS]:<66030401> Failed to retrieve OCSP status

OCSP not available\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-MISMATCH_BP_CONFIGURATION_SETTING_VALUE

4-Warning

<132>CMTS[DOCSIS]: Misconfigured BPI Setting: gracetime Type [dec] is longer than 50%% of lifetime. CM MAC Addr <[enet]>

Misconfigured BPI Configuration Setting Value \n

ubr7200

"Please inspect the configuration file"

UBR7200-4-MISMATCH_BP_REVOCATION_TIMEOUT_VALUE

4-Warning

<132>CMTS[DOCSIS]: Misconfigured BPI Setting: [chars] Type [dec] is longer than revocation timeout value. CM MAC Addr <[enet]>

Misconfigured BPI Configuration Setting Value \n

ubr7200

"Please inspect the configuration file"

UBR7200-3-KEY_REJECT_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66050102> Key Reject - No Information. CM Mac Addr <[enet]>

Key Reject No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-KEY_REJECT_UNAUTHORIZED_SAID

3-Error

<132>CMTS[DOCSIS]:<66050103> Key Reject - Unauthorized SAID. CM Mac Addr <[enet]>

Key Reject Unauthorized SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-TEK_INVALID_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66050203> TEK Invalid - No Information. CM Mac Addr <[enet]>

TEK Invalid No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-TEK_INVALID_INVALID_KEY_SEQUENCE_NUMBER

3-Error

<132>CMTS[DOCSIS]:<66050206> TEK Invalid - Invalid Key Sequence Number . CM Mac Addr <[enet]>

TEK Invalid - Invalid Key Sequence Number\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BPI_WARNING

4-Warning

[chars]: SID=[dec] KeySeq=0x[hec] Cable Interface <[chars]>

BPI Warning \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-WB_BPI_ERR

3-Error

[chars]: [dec] [dec] [dec]

WB BPI Error \n

ubr10000

LOG_STD_NO_ACTION

UBR7200-4-NB_MCAST_BPI_EXCEED_WAR

4-Warning

[[chars] [chars]] BPI:More than [dec] mcast sessions joined for CM [enet] ignored

NB mcast BPI warning \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-SA_MAP_UNSUPPORTED_CRYPTO_SUITE

3-Error

<132>CMTS[DOCSIS]:<66060200> Unsupported Crypto Suite. CM Mac Addr <[enet]>

Unsupported Crypto Suite\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAP_REJECT_NOT_AUTH_DS_TRAFFIC

3-Error

<132>CMTS[DOCSIS]:<66060509> Map Reject - Not Authorized for requested downstream traffic flow. CM Mac Addr <[enet]>

Map Reject - Not Authorized for requested downstream traffic flow \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-MAP_REJECT_DS_TRAFFIC_FLOW_NOT_MAPPED

6-Information

<132>CMTS[DOCSIS]:<66060510> Map Reject - Downstream traffic flow not mapped to BPI+SAID. CM Mac Addr <[enet]>

Map Reject - Downstream traffic flow not mapped to BPI+SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAPPED_TO_EXISTING_SAID

3-Error

<132>CMTS[DOCSIS]:<66060600> Mapped to existing SAID. CM Mac Addr <[enet]>

Mapped to existing SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAPPED_TO_NEW_SAID

3-Error

<132>CMTS[DOCSIS]:<66060700> Mapped to new SAID. CM Mac Addr <[enet]>

Mapped to new SAID \n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REQ_REJ_ALREADY

4-Warning

<133>CMTS[DOCSIS]:<67020100> DCC rejected already there. CM Mac Addr <[enet]>

DCC rejected already there

ubr7200

"Wait until the transaction ends.Otherwise try another channel ID to move the modem "

UBR7200-4-DCC_REQ_DEPART_OLD

4-Warning

<133>CMTS[DOCSIS]:<67020200> DCC depart old. CM Mac Addr <[enet]>

DCC depart old

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REQ_ARRIVE_NEW

4-Warning

<133>CMTS[DOCSIS]:<67020300> DCC arrive new. CM Mac Addr <[enet]>

DCC arrive new

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REQ_ABORT_NO_COMM_NEW_UPSTREAM_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<67020600> DCC aborted unable to communicate on new upstream channel. CM Mac Addr <[enet]>

DCC aborted unable to communicate on new upstream channel

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<67020700> DCC rejected unspecified reason. CM Mac Addr <[enet]>

DCC rejected unspecified reason

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_PERMANENT_DCC_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<67020800> DCC rejected permanent - DCC not supported. CM Mac Addr <[enet]>

DCC rejected permanent - DCC not supported

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<67021000> DCC rejected required parameter not present. CM Mac Addr <[enet]>

DCC rejected required parameter not present

ubr7200

"Double check the parameters while sending the DCC-REQ"

UBR7200-4-DCC_REJ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<67021700> DCC rejected message syntax error. CM Mac Addr <[enet]>

DCC rejected message syntax error

ubr7200

"Check the TLV and parameters set while sending the DCC-REQ"

UBR7200-4-DCC_REJ_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<67021800> DCC rejected message too big. CM Mac Addr <[enet]>

DCC rejected message too big

ubr7200

"Mimimize the msg length to be less than 1536"

UBR7200-4-DCC_REJ_20_DISABLE

4-Warning

<133>CMTS[DOCSIS]:<67021900> DCC rejected 2.0 mode disabled. CM Mac Addr <[enet]>

DCC rejected 2.0 mode disabled

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<67021100> DCC rejected authentication failure. CM Mac Addr <[enet]>

DCC rejected authentication failure

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_SRV_FLOW_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<67020900> DCC rejected service flow not found. CM Mac Addr <[enet]>

DCC rejected service flow not found

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<67021200> DCC rejected multiple errors. CM Mac Addr <[enet]>

DCC rejected multiple errors

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<67021500> DCC rejected duplicate SF reference-ID or index in message. CM Mac Addr <[enet]>

DCC rejected duplicate SF reference-ID or index in message

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_REJ_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<67021600> DCC rejected parameter invalid for context. CM Mac Addr <[enet]>

DCC rejected parameter invalid for contex

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_RSP_NOT_RCV_OLD_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<67030100> DCC-RSP not received on old channel. CM Mac Addr <[enet]>

DCC-RSP not received on old channel

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_RSP_NOT_RCV_NEW_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<67030200> DCC-RSP not received on new channel. CM Mac Addr <[enet]>

DCC-RSP not received on new channel

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_RSP_REJ_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<67030300> DCC-RSP rejected unspecified reason. CM Mac Addr <[enet]>

DCC-RSP rejected unspecified reason

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_RSP_REJ_UNKNOWN_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<67030400> DCC-RSP rejected unknown transaction ID. CM Mac Addr <[enet]>

DCC-RSP rejected unknown transaction ID

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_RSP_REJ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<67030600> DCC-RSP rejected message syntax error. CM Mac Addr <[enet]>

DCC-RSP rejected message syntax error

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_RSP_REJ_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<67030500> DCC-RSP rejected authentication failure. CM Mac Addr <[enet]>

DCC-RSP rejected authentication failure

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DCC_ACK_REJ_UNKNOWN_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<67040300> DCC-ACK rejected unknown transaction ID. CM Mac Addr <[enet]>

DCC-ACK rejected unknown transaction ID

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-5-KEEPALIVE

5-Notice

Keepalive shutting down interface [chars].

No activity detected within the Keepalive timeout period on the interface.

ubr7200

"Check RF path for failure."

UBR7200-6-MACCLTCLR

6-Information

Enable mac mgmt msg processing on [chars].

The RP has reenabled the sending of DOCSIS MAC-layer messages on the cable interfaces after an N+1 switchover.

ubr7200

"No action needed."

UBR7200-0-TEST_CABLE

0-Emergency

CMTS[dec]/[dec]/[dec] schrp_cli_cmd function failed in [chars]

Most likely S/W failure

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200-3-FPSUBINIT

3-Error

Unable to create subinterface [chars] for hw interface [chars]

The system was unable to create the cable subinterface data structures

ubr7200

"Gather information about running configuration and amount of memory " "in the system and file a bug"

UBR7200-3-LB_MODEM_FAILED

3-Error

Failed to move modem [enet] from [chars] to [chars].

Load balancing failed to move a modem from one interface to another.

loadbalance

"Check RF path for failure. " "Check if upstream and/or downstream channels are combined " "as expected"

UBR7200-6-LB_MODEM_SUCCESS

6-Information

Succeeded to move modem [enet] from [chars] to [chars].

Load balancing succeeded to move a modem from one interface to another.

loadbalance

"LOG_STD_NO_ACTION"

UBR7200-3-LB_IF_DISABLED

3-Error

Disabled interface [chars]

Load balancing disabled the interface because it could not move modems from or to it.

loadbalance

"Check RF path for failure. " "Check if upstream and/or downstream channels are combined " "as expected"

UBR7200-3-LB_STALE_PENDING_CM

3-Error

This is a pre-exist pending entry print info to debug further... [enet] action 0x[hec]:0x[hec] client [dec]:[dec] src_upd_already [dec]

Stale Pending CM Exist

loadbalance

"Contact Cisco TAC"

UBR7200-4-LB_CM_LIST_DUP_ENTRY

4-Warning

CM [enet] on CM List 0x[hec] group [dec]

Duplicate entry in cm list exists. No Operational Impact.

loadbalance

"LOG_STD_NO_ACTION"

UBR7200-4-LB_CM_LIST_MISMATCH_ENTRY

4-Warning

CM [enet] on CM List 0x[hec] group [dec] action [dec]

Entry in CM list seen at different position than expected . There is no operational impact

loadbalance

"Please copy the error message exactly as it appears on the console or in the " "system log contact your technical support representativeand provide the " "representative with the gathered information. "

UBR7200-6-LB_RFCH_SET_OVERLAP

6-Information

Rf-channel sets overlap in LBG [chars].

Detect RF channel sets overlap in this Docsis LBG. It will cause D3.0 dynamic LB algorithm may not work optimally.

loadbalance

-

UBR7200-6-LB_INTERVAL_UNSUITABLE

6-Information

The interval value [dec] for LBG [chars] is too small or too big.

The recommanded interval value is between 10 to 300.

loadbalance

-

UBR7200-6-LB_RFCH_SIZE_EXCEED

6-Information

Rf-channel size in LBG [chars] exceeds the limit maximum [dec]

The rf-channel size in LBG exceeds the limit. It will cause D3.0 dynamic LB algorithm may not work optimally.

loadbalance

-

UBR7200-4-LB_COUNT_OUT_OF_RANGE

4-Warning

Grp [dec] MD [chars] [chars] Chan [dec] CM [enet] [chars] Counter Out of Range value [dec] New State [chars] Old [dec] Skip Reason [chars]

LB modem counter decrements out of range.

loadbalance

"LOG_STD_NO_ACTION"

UBR7200-3-PKTCBL_INVALID_GATE_ID

3-Error

if_index_db is null index = [dec] gid = [dec]

PacketCable encounters invalid gate id to look up from its DB

packetcable

"SW code path errors"

UBR7200-6-PKTCBL_COPS_CONNECTION_DOWN

6-Information

Cops connection: IP addr: [inet] Handle: 0x[hec] went down Error code: [dec]

Cops connection went down

packetcable

"Check cops connection"

UBR7200-6-PKTCBL_COPS_CONNECTION_UP

6-Information

Cops connection: IP addr: [inet] Handle: 0x[hec] is up

Cops connection is up

packetcable

LOG_STD_NO_ACTION

UBR7200-3-L2VPNNOTSUPPORTED

3-Error

L2 VPN ATM-VC mapping not currently supported on mc28u card. CM MAC [enet].

ATM-VC mapping configured for a cable modem on an mc28u card.

TLS

"Disable the L2 VPN ATM- VC mapping on mc28u cards."

UBR7200-3-L2VPNMAXLIMIT

3-Error

L2VPN XCONNECT PW max limit of [dec] pseudo-wires reached.

L2VPN XCONNECT PW max limit of pseudo-wires reached.

cmts-application

"Cannot configure anymore pseudo-wires"

UBR7200-4-L2VPN_TLVERR

4-Warning

L2VPN XCONNECT PW Cable Modem CM config file TLV Error.

L2VPN XCONNECT PW TLV Error VCID or SAII or TAII not valid

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_ERROR_BPI_NOT_ENABLED

4-Warning

L2VPN enabled without enabling BPI+ or 1.0 CM [enet] [chars]

Encryption not enabled for L2VPN CM

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_CMIM_ERROR

4-Warning

ERROR: CM [enet] [chars] Top Level CMIM TLV does not exclude eCM

Top Level CMIM TLV does not exclude eCM

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_VPNID_MISSING_ERROR

4-Warning

ERROR: CM [enet] [chars] VPNID TLV missing at top level

VPNID TLV missing at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLSPEERNAME_LEN_ERROR

4-Warning

ERROR: CM [enet] [chars] MPLSPEERNAME TLV length invalid

MPLSPEERNAME TLV length invalid

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_NSI_MISSING_ERROR

4-Warning

ERROR: CM [enet] [chars] VLANID or MPLSPEER TLV missing at top level

VLANID or MPLSPEER TLV missing at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_NSI_DUPLICATE_ERROR

4-Warning

ERROR: CM [enet] [chars] VLANID and MPLSPEER TLV both present at top level

VLANID and MPLSPEER TLV both present at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_VCID_OR_TAII_SAII_MISSING_ERROR

4-Warning

ERROR: CM [enet] [chars] VCID or TAII & SAII TLV missing or out-of-range

VCID or TAII & SAII TLV missing or out-of-range

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_PWTYPE_ERROR

4-Warning

ERROR: CM [enet] [chars] MPLS PW TYPE TLV invalid at top level

MPLS PW TYPE TLV invalid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLSPEER_ERROR

4-Warning

ERROR: CM [enet] [chars] MPLS PEER IPADDR TLV invalid at top level

MPLS PEER IPADDR TLV invalid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MULTIPLE_VPNID_ERROR

4-Warning

ERROR: CM [enet] [chars] Multiple L2VPN TLV with same vpnid at top level

Multiple L2VPN TLV with same vpnid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_DUPLICATE_VLANID_ERROR

4-Warning

ERROR: CM [enet] [chars] Multiple L2VPN TLV with same vlanid at top level

Multiple L2VPN TLV with same vlanid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_US_SFLOW_VPNID_ERROR

4-Warning

ERROR: CM [enet] [chars] Matching TopLevel L2VPNID not found for US-SF

Matching TopLevel L2VPNID not found for US-SF

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_DS_CFR_VPNID_ERROR

4-Warning

ERROR: CM [enet] [chars] Matching TopLevel L2VPNID not found for DS-CFR

Matching TopLevel L2VPNID not found for DS-CFR

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_BKUP_PRIO_ERR

4-Warning

ERROR: CM [enet] [chars] Incorect or missing priority for backup peer

Priority incorrect or missing for backup peer

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_BKUP_EXCEEDED

4-Warning

ERROR: CM [enet] [chars] Too many backup peers

Too many backup peers

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_BKUP_DISABLE_CFG_ERR

4-Warning

ERROR: CM [enet] [chars] Bkup disable delay and never disable bkup both configured

Both TLVs cannot be configured

cmts-application

"Check CM config file"

UBR7200-6-DSG_ALL_TUNNEL_REMOVED

6-Information

all DSG tunnels are removed on interface [chars] and it's subinterfaces

DSG is disabled on the interface

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DSG_HBEAT_FAILED

3-Error

Interface [chars] failed to send hbeat packet for vendor [chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-BUN_MCAST_NOFREE_MAC

3-Error

Fail to allocate free Bundle Multicast Map Entry for Bundle:[dec] Group:[inet] Source:[inet] IDB:[chars]

An internal software error occured

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200-3-BUN_MCAST_REV_MAP_ERR

3-Error

Unable to find the Multicast Mapped Entry from reverse-mapping table for Bundle: [dec] MAC:[enet]

An internal software error occured

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support respresentative."

UBR7200-3-BUN_MCAST_INIT

3-Error

Unable to allocate memory for bundle multicast initialization.

An internal software error occured

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support respresentative."

UBR7200-6-CONFIG_EXIT

6-Information

Exiting config mode by [chars] since Port Adapter in slot [dec] removed

The user was configuring a port adapter which was either removed from the system or if an mc28u card was reset. Therefore the configuration mode is invalid and terminated by IOS

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DDC_UNEXPECTED_NODES

3-Error

The number of nodes [dec] is invalid

The number of nodes is either smaller or greater than the limits supported by the platform

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-3-DDC_INVALID_STATICMAP

3-Error

The node [dec] for mac-address [enet] exceeds maximum configured nodes

A mapping specified by the oui-map or mac-map commands exceeds the configured number of participant nodes

ddc

"Fix configuration"

UBR7200-4-DDC_CFG_HASHID

4-Warning

Hash id [dec] does not exist in global configuration

A hash id is configured for a cable interface but is not defined globally

ddc

"Fix configuration"

UBR7200-3-DDC_INVALID_HASHTYPE

3-Error

The hash type [dec] for hash id [dec] is invalid

Software does not recognize the configured hash type

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_PROT_FREQ_ERROR

4-Warning

DS frequency not configured for the protect target node [dec]

DS frequencies are not configured for all protect targets

ddc

"Fix configuration"

UBR7200-4-DDC_SEMAPHORE_ERROR

4-Warning

DDC semaphore released when it was not taken

DDC semaphore was not take when release was requested

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_UNEXPECTED_MESSAGE_ERROR

4-Warning

DDC unexpected message error [dec]

DDC received an unexpected or unsupported message

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_UNEXPECTED_EVENT_ERROR

4-Warning

DDC unexpected event error [dec]

DDC received an unexpected or unsupported event

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_MESSAGE_ERROR

4-Warning

DDC message error. type [dec]

DDC failed to send interprocess or IPC message

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_LIST_ERROR

4-Warning

DDC list error

DDC failed to create or add element to list

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_NODE_ID_ERROR

4-Warning

Node id mismatch NPE: [dec] linecard: [dec]

Node id's on NPE subinterface is different than on linecard

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_GENERAL_ERROR

4-Warning

Error: [chars]

Catchall error message for DDC

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-6-DDC_CFG_HASHFILTER_REMOVED

6-Information

Hash-filter [dec] not present in global config - Filter removed from [chars]\n

The hash-filter was removed from the global config while the card was not present in the chassis therefore the corresponding interface hash filter is removed from the config

ddc

LOG_STD_NO_ACTION

UBR7200-6-DDC_CFG_TARGET_REMOVED

6-Information

Redundancy target invalid - removed from [chars]\n

The router's my_id was config removed while the card was not present in the chassis therefore the redundancy target cli is removed from the interface

ddc

LOG_STD_NO_ACTION

UBR7200-3-ALARM_ERROR

3-Error

[chars]

General error information.

ubr7200

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200-6-ALARM_INFO

6-Information

[chars] [chars] [chars] [chars] [chars]

Alarm assertion or deassertion information.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DISCOVER_FAIL

3-Error

[chars]

Unable to discover physical entity

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-4-DCC_NO_RESOURCE_ON_TARGET

4-Warning

DCC [enet] aborted. No resource available on target [chars] U[dec]

No resource available on target channel for the DCC transaction

ddc

"Check target channel utilization"

UBR7200-5-CLONED_CM_DETECTED

5-Notice

Cloned CM with MAC address [enet] connection attempt rejected on [chars] U[dec]

There might be a hacking attempt going on.

ubr7200

"Look for possible hacking attempt"

UBR7200-3-FLOW_ERR

3-Error

Flow error sfid [dec] sid [dec] CM Mac address <[enet]>

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-DS_FLOW_INCONSIST_WB_INFO

3-Error

DS Flow Error: [chars] [enet] prim_rfid [dec] sfid [dec] wb_mode [dec] forw_chid [dec] [chars]

-

-

-

UBR7200-3-DS_FLOW_INCONSIST_WB_INFO

3-Error

DS Flow Error: [chars] [enet] prim_rfid [dec] sfid [dec] wb_mode [dec] forw_chid [dec] [chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-DIV_BY_ZERO_ERROR

3-Error

Divide by zero attempted error [chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-6-CACHE_ENGINE_BUF_FULL

6-Information

Max. cache buffer has been reached!

Max. cache buffer has been reached. cache engine service for current request is denied.

snmpPerf

"."

UBR7200-4-CACHE_ENGINE_WARNING

4-Warning

Warning: [chars] - [dec]

Cache engine warning message.

snmpPerf

"."

UBR7200-4-SERVICE_FLOW_ERROR

4-Warning

CM MAC: [chars] Service flow direction: [chars] Param code: [dec] Confirm code: [dec]

Looks like issue while admitting/activating Service flow

ubr7200

"Please look for DOCSIS message logs followed for more details"

UBR7200-4-SERVICE_FLOW_ZERO_BLAZE_INDEX_ERROR

4-Warning

spa_num: [dec] spa_if_num: [dec] nb_unique_index: [dec] lc_slot: [dec] lc_subslot: [dec] SFID: [dec] Blaze index: [dec]

Looks like issue while allocating remote downstream blaze index

ubr7200

"Please see show cable modem and " "show int cx/y/z service-flow for more details"

UBR7200-4-SERVICE_FLOW_INDEX_ERROR

4-Warning

[chars] [dec]/[dec] nb_unique_index: [dec] SFID: [dec] index: [dec] flow-chid: [dec] wb-mode: [dec] dsid: [dec] cm [enet]

Looks like issue while allocating remote downstream index

ubr7200

"Please see show cable modem pri and " "show int cx/y/z service-flow for more details"

UBR7200-3-SNMPMALLOC

3-Error

no sufficient memory for sorted table index [dec] allocated %lu unallocated %lu

There is no enough memory to allocate for AVL tree

ubr7200

"No action needed."

UBR7200-2-CMTS_INDEX_TABLE_FULL

2-Critical

[chars] Index table full - req [dec]/[dec]/[dec]:[dec] if_idx [dec] sid [dec] no-elem [dec] [[chars]]\n

The specified Index table is full. This indicates a likely software defect in one of the applications that use this index. Please run show tech to collect additional debug information.

ubr7200

"Please copy the error message exactly as it appears on the console or in the " "system log contact your technical support representativeand provide the " "representative with the gathered information. "

UBR7200-4-CLASSIFIER_ERROR

4-Warning

CM MAC: [chars] Classifier direction: [chars] Param code: [dec] Confirm code: [dec]

Looks like issue while admitting/activating Classifier

ubr7200

"Please look for DOCSIS message logs followed for more details"

UBR7200-4-PHS_ERROR

4-Warning

CM MAC: [chars] PHS_ERROR Param code: [dec] Confirm code: [dec]

Looks like issue with PHS header

ubr7200

"Please look for DOCSIS message logs followed for more details"

UBR7200-4-DSX_MSG_ERROR

4-Warning

CM MAC: [chars] MSG type: [chars] Error code: [dec] MSG: [chars].

Received invalid DSX message.

ubr7200

"Please turn on debug to see detailed DSX messages."

UBR7200-3-MAX_DS_SF_ERROR

3-Error

Maximum limit for downstream service-flows reached

The number of DS service-flows cannot exceed 50

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-CMTS_OIR_INACTIVE_WITHOUT_L2VPN_UNCONFIGURED

4-Warning

Card on [dec]/[dec] with l2vpn \[chars]\ command should be taken care of before plugging different type of card or executing \no card\ command.

Card is configured with cable l2vpn commands please take care of these configurations before plugging different type of card or executing \no card\ command.

cmts-application

"."

UBR7200-6-CM_OFFLINE_WITH_L2VPN_NOT_ENABLE

6-Information

DOCSIS L2VPN not enabled sending CM [enet] offline

Cable Modem is configured with L2VPN but CMTS L2VPN isn't enabled. Send offline message to CM.

cmts-application

"Configure \"cable l2-vpn-service xconnect nsi dot1q interface ..\" and " " \"cable l2-vpn-service nsi dot1q\" commands."

UBR7200-6-CM_OFFLINE_WITH_MPLS_L2VPN_NOT_ENABLE

6-Information

DOCSIS MPLS L2VPN not enabled sending CM [enet] offline

Cable Modem is configured with L2VPN but CMTS MPLS L2VPN isn't enabled. Send offline message to CM.

cmts-application

"Configure \"cable l2-vpn-service xconnect nsi mpls\" command."

UBR7200-6-CM_OFFLINE_WITH_LEGACY_TLS_CONFIGURED

6-Information

Already configured for legacy TLS sending CM [enet] offline

Legacy TLS is already configured. Send offline message to CM.

cmts-application

"Check CMTS configuration for legacy TLS with this CM"

UBR7200-6-CM_OFFLINE_WITH_VLANID_USED

6-Information

VLANID [dec] on [chars] in use sending CM [enet] offline

VLANID is in use. Send offline message to CM.

cmts-application

"Check L2VPN VLANID specified in CM configuration file"

UBR7200-6-CM_OFFLINE_WITH_DUP_MPLSPEER_VCID

6-Information

MPLS PEER [inet] VCID [dec] in use sending CM [enet] offline

MPLS PEER & VCID is in use. Send offline message to CM.

cmts-application

"Check L2VPN MPLS PEER & VCID specified in CM configuration file"

UBR7200-6-CM_OFFLINE_WITH_UNRESOLVED_MPLSPEER_NAME

6-Information

Unable to resolve MPLS NAME [chars] VCID [dec] sending CM [enet] offline

Unable to resolve MPLS NAME via DNS. Send offline message to CM.

cmts-application

"Check L2VPN MPLS PEERNAME specified in CM configuration file" "Or DNS configuration and setup"

UBR7200-6-INTERNAL_XCONNECT_INTERFACE_ERROR

6-Information

Unable to create internal xconnect bundle interface

Unable to find free bundle interface for l2vpn xconnect function

cmts-application

"Free one bundle interface for internal l2vpn xconnect function"

UBR7200-6-CM_OFFLINE_WITH_NO_FREE_VPNID

6-Information

No free VPNIDs remaining sending CM [enet] offline

There aren't any free VPNIDs. Send offline message to CM.

cmts-application

LOG_STD_SH_TECH_ACTION

UBR7200-3-INVALID_INVOKE_FROM_ISR

3-Error

Invalid [chars] from interrupt level [dec]

Invalid operation from ISR context. Possible recurrence of CSCek63728

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-INVALID_US_CHID

3-Error

Invalid Upstream Channel ID

An internal software error occurred.

cmts-docsis

LOG_STD_SH_TECH_ACTION

UBR7200-4-UCC_RSP_NOT_RCV_ON_CHANNEL_ID

4-Warning

<133>CMTS[DOCSIS]:<67010100> UCC-RSP not received on previous channel ID. CM Mac Addr <[enet]>

-

ubr7200

"Connect DOCSIS compliant Cable Modem"

UBR7200-4-UCC_RSP_RCV_INVALID_CHANNEL_ID

4-Warning

<133>CMTS[DOCSIS]:<67010200> UCC-RSP received with invalid channel ID. CM Mac Addr <[enet]>

-

ubr7200

"Enable <cmdBold>debug cable ucc<noCmdBold> at CMTS " "and make sure that CMTS sends UCC-REQ with correct " "channel ID. If CMTS is not sending the correct " "channel ID report the problem"

UBR7200-4-UCC_RSP_RCV_INVALID_CHANNEL_ID_NEW

4-Warning

<133>CMTS[DOCSIS]:<67010300> UCC-RSP received with invalid channel ID on new channel. CM Mac Addr <[enet]>

-

ubr7200

"Connect DOCSIS compliant Cable Modem"

UBR7200-3-CMTS_TCC_RNG_INVALID_SB

3-Error

TCC RNG on Interface [chars] with invalid SB for CM [enet]

TCC RNG could not get a valid subblock for the interface that the CM is ranged on. SW Bug.

ubr10000

LOG_STD_NO_ACTION

UBR7200-4-CM_SF_DSID_INCONSISTENT

4-Warning

DSID [dec] BG: [dec] assigned to SF:[dec] already. DSID invalid on CM-[enet]

DSID assigned to SF not valid any longer. SW Bug

ubr10000

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DSID_DUPLICATE

4-Warning

Duplicate DSID [dec]/[dec]/[dec]: [dec] detected

Detected an attempt to enqueue a duplicate DSID. SW Bug

ubr10000

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-5-ATTRIBUTE_CHANGE_CONFLICT

5-Notice

<133>CMTS[DOCSIS]:<75010100> Attribute Masks for SF SFID %lu do not

Change in provisioned attribute mask causes mismatch

ubr10000

"Modify provisioned attributes such that it meets " "requirements"

UBR7200-4-TEMPLATE_LKUP_ERROR

4-Warning

CM MAC: [enet] Sid: [dec] Act_Qos: [dec]

Problem while looking up qos template

ubr7200

"LOG_STD_SH_TECH_ACTION"

UBR7200-4-DIAG_LOG_HIGH_THRSHLD_REACHED

4-Warning

[DOCSIS]:<86000100>Docs Diag Log exceeds high threshold

Docs Diag Log Notification :log size exceeds high threshold

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-5-DIAG_LOG_LOW_THRSHLD_REACHED

5-Notice

[DOCSIS]:<86000200>Docs Diag Log reaches low threshold

Docs Diag Log Notification :log size reaches low threshold

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DIAG_LOG_FULL_REACHED

4-Warning

[DOCSIS]:<86000300>Docs Diag Log reaches max size

Docs Diag Log Notification: log size reaches max size

ubr7200

-

UBR7200-2-LOG_CON_SYS_CRIT

2-Critical

[chars] logging console level to [dec] from [dec] Rate-limit level [dec] [chars].

Logging console restricted during critical situations

ubr7200

"Please run 'show logging' to view all sys-logged messages"

UBR7200-3-JIB_Q_LENGTH_PHS_ERR_DETECTED

3-Error

JIB Upstream Queue Length or PHS Rule Failure Detected.

-

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-GRD_HCCP_RECOVER

3-Error

Wideband-Cable[dec]/[dec]/[dec]:[dec] not recovered after switchover

After a switchover or revert where the modular-host for a SPA becomes active on the standby a wideband interface on that SPA is not recovered. This is most likely due to a software problem.

cmts-redundancy

LOG_STD_SH_TECH_ACTION

UBR7200-3-GRD_HCCP_REMOVE

3-Error

Wideband-Cable[dec]/[dec]/[dec]:[dec] not removed

When the modular-host configuration for a SPA is removed a wideband interface on that SPA is not removed. This is most likely due to a software problem.

cmts-redundancy

LOG_STD_SH_TECH_ACTION

UBR7200-6-COMPAT_NEW_CARD

6-Information

The old card <[chars]> is replaced by new card <[chars]> in slot [dec].

OIR: card replacement

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-COMPAT_SHUTDOWN_CARD

6-Information

Failed to restore the configuration for [chars].

OIR-compatiblity configuration restore failed

ubr7200

"Configure the interface manually"

UBR7200-4-BLZE_HM_TEST

4-Warning

Blaze HM testcase failed. Blaze indices allocated for MD host [dec]/[dec] on the Guardian [dec]/[dec] : [dec] Blaze indices in use on the MD Host: [dec]

The blaze indices have not been deallocated on the Guardian

ubr10000

LOG_STD_NO_ACTION

UBR7200-4-GRD_UNAVAIL

4-Warning

Unable to reach Card [dec]/[dec] for Modular-host services

The Guardian card is down or the IPC to the Guardian card is down

ubr10000

"Make sure the card selected to be Modular-host is " "operational or change the relevant Modular-host config to" "use an operational card."

UBR7200-3-METERING_NOFILESYS_SFLOG

3-Error

No file system can be used for sflog file.

Cannot found a suitable file system to store sflog file.

ubr7200

"Please check whether disk0: or disk1:" " are ready or full."

UBR7200-3-IPDR_FILESYS_FULL

3-Error

File [chars] cannot be created/written since filesystem is full.

The IPDR feature requires a file to be written to filesystem. Since filesystem is full it might result in lost IPDR data.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-IPDR_BUFFER_ERR

3-Error

unable to alloc buffer because percent of free memory is [dec] which is below [dec]

The IPDR feature requires memory to hold record. Since insufficient memory it might result in lost IPDR data

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-IPDR_GET_MACDOMAIN_ERR

3-Error

[chars]

The IPDR CM_US failed to get MAC domain by docsIf3CmtsCmRegStatusId.

ubr10000

"Ignore this IPDR record collecting records at next interval."

UBR7200-3-CMTS_QUACK_FAIL_ERR

3-Error

[chars]

This LC requires programmed Quack IDPROM.

ubr10000

LOG_STD_SH_TECH_ACTION

UBR7200-3-UCDPROCERR

3-Error

CMTS UCD processing failed on [chars] U[dec] lch_state [dec] err [dec] retry [dec]

UCD update error

cmts-infra

"Check the system CPU load and reset the upstream"

UBR7200-5-UCDCCCERR

5-Notice

CMTS UCD failed to update CCC on [chars] U[dec] lch_state [dec]

UCD update CCC error

cmts-infra

"Check the lch_state reset the upstream if necessary"

UBR7200-5-USPHYTSSDISC

5-Notice

PHY TSS discontinuous on [chars] U[dec] old<T [hec] M [hec] F [hec]> new<T [hec] M [hec] F %4x> start<T [hec] M [hec] F %4x> mac<T [hec] M [hec] F %4x> tgc/frame [hec] mslot/frame [hec]

PHY TSS error

cmts-infra

"If the problem is persistent modify minislot size and reset the upstream"

UBR7200-5-USPHYTSSLATE

5-Notice

PHY late TSS on [chars] U[dec] MAC [hec] phy <last [hec] curr [hec]> tgc/frame [hec]

late PHY TSS SNAPSHOT messages are received

cmts-infra

"This is an internal failure and not necessarily problematic"

UBR7200-5-USTSSMISMATCH

5-Notice

MAC-PHY TSS mismatch [chars] U[dec]: MAC<T [hec] M [hec] F [hec]> PHY<T [hec] M [hec] F [hec]> Old-PHY<T [hec] M [hec] F [hec]> start<T [hec] M [hec] F [hec]> curr [hec] tgc/fame [hec] mslots/fame [hec]

Mis-matched MAC-PHY TSS is detected

cmts-infra

"This is an internal failure and not necessarily problematic"

UBR7200-5-USTSSNOTALIGNED

5-Notice

MAC-PHY TSS on [chars] U[dec] not at frame boundary MAC<T [hec] M [hec] F [hec]> start <T [hec] M [hec] F [chars]> current<T [hec]> tgc/frame [hec] mslot/frame [hec]

PHY TSS is not sampled at frame boundary

cmts-infra

"This is an internal failure and not necessarily problematic"

UBR7200-5-USPHY_BAD_INTR

5-Notice

USPHY with physical channel [dec] gets too many error interrupts

US PHY or MAC chips on the LC get into a bad state and SW can not recover it

ubr7200

"Collect show tech and then power cycle the Line card." "If problem does not recover contact Cisco for support"

UBR7200-4-CMTS_RF_POWER_ADJUST

4-Warning

rf-power adjusted to [dec] dBmV to meet upconvertor requirement.

This card has an upconvertor that has different limits on rf-power. rf-power has been adjusted to meet these limits.

ubr10000

"LOG_STD_NO_ACTION"

UBR7200-4-MCAST_ADMISSION_CONTROL_FAILURE

4-Warning

Multicast Service flow creation failed - group [chars] source [chars] host Interface [chars]

service flow creation failure due to admission control check.

ubr7200

"Adjust the min-rate parameter mentioned" " as part of the service class"

UBR7200-4-MCAST_DB_MAX_LIMIT_REACHED

4-Warning

Multicast DB full new entry not created - max [dec] group [chars] source [chars] fwd Interface [chars] bundle [chars]

Multicast explicit tracking DB entry creation failed due to max limit reached

ubr7200

"Reduce Static IGMP multicast config or wait for" "Dynamic IGMP OR PCMM multicast clients to leave"

UBR7200-4-MCAST_DBC_FAILED_BLOCKED_CM

4-Warning

CM [enet] failed to join [chars] [chars] on Interface [chars] [chars] due

Multicast DBC failed for the CM because of system busy or too high channel change rate for the CM.

ubr7200

"Lower channel change rate for the" "CM or check whether system CPU are too busy."

UBR7200-3-MCAST_DA_TO_DSID_DUPLICATED

3-Error

DA [enet] to DSID table duplicated when operation [chars] DSID [dec] on

Multicast DA_TO_DSID table in LC should be unique for DA on a interface.

ubr7200

"Reconfigure DSG configure in the mac domain" " to refesh all DSG configure in the interface."

UBR7200-6-MCAST_IPC_HEADER_ADD_FAILURE

6-Information

Multicast IPC header could not be added for source [chars] group [chars] fwd interface [chars]

Multicast IPC header could not be added

ubr7200

LOG_STD_ACTION

UBR7200-3-CMTS_RCC_CREATION_FAILURE

3-Error

RCC creation failure - ID [dec] owner [chars] host [chars]

RCC creation failed due to list insert failure.

cmts-docsis

LOG_STD_SH_TECH_ACTION

UBR7200-5-MACTSSLDERR

5-Notice

CMTS MAC TGC load pulse error sync-pulse interval [dec]

MAC FPGA TGC load pulse generation error

ubr7200

"Replace defective Line Card"

UBR7200-3-NULLIDBTTSVTBL

3-Error

A Null sw idb prevents pxf src-vfy tables from being updated MAC [enet] SID [dec]

A failure occurred in trying to update pxf src-vfy tables

ubr10000

"Copy the error message exactly as it appears and report it to your" "technical support representative."

UBR7200-3-NULLHWIDB

3-Error

A Null hwidb prevents the acl update for a modem's associated hosts MAC [enet] SID [dec]

A failure occurred in trying to update acl for a modem's associated host

ubr10000

"Copy the error message exactly as it appears and report it to your" "technical support representative."

UBR7200-6-CPE_MOVED_FROM_WRONG_SID_CHAIN

6-Information

CPE [enet] was moved from SID Chain [dec] to [dec] from [chars] of the chain

The CMTS automatically corrected a condition where the CPE was in the wrong SID chain.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DUPIPV6_SIDMISMATCH

4-Warning

Duplicate IPv6 Address %P in [chars] Sid [dec] MAC:[enet]. Dup Original Sid [dec]

Duplicate IPv6 Address found with different sid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-ACFE_FAILURE

3-Error

[chars]

A failure occurred in ACFE algoirhtm module

cmts-qos

LOG_STD_ACTION

UBR7200-6-ACFE_NOTIFICATION

6-Information

[chars]

A special event happened in ACFE algorithm module

cmts-qos

LOG_STD_NO_ACTION

UBR7200-3-PA_REM_GENERAL

3-Error

[chars]

A general failure occured in the operation of the PA removal event state machine as defined by the failure string

ubr7200

LOG_STD_ACTION

UBR7200-3-PA_REM_ENQFAIL

3-Error

Enqueue of message failed slot [dec]

Enqueue of a PA removal message to an event queue failed

ubr7200

LOG_STD_ACTION

UBR7200-3-PA_REM_PCI_ERROR

3-Error

PCI error address = 0x[hec]\n

An unexpected PCI error happened

ubr7200

LOG_STD_ACTION

UBR7200-3-ENVM_FAN_OVERLOAD

3-Error

Fan Tray overloaded fail to support the linecard at slot [dec]

The cooling power provided by the routers's fans is lower than \n\ some LCs in chassis required.

-

"Replace the fan as soon as possible or the system may shut itself \n\ down or fail to operate properly."

UBR7200-6-CNNR_NOSHR

6-Information

Failed to map C[dec]/[dec]/[dec]/U[dec] to connector [dec] already mapped by C[dec]/[dec]/[dec]/U[dec].

Some connectors do not support frequency stacking. They can only be mapped by one upstream at a time. This may happen on MC28 cards.

ubr7200

"Remove the existing mapping on the connector."

UBR7200-6-CNNR_NOXC

6-Information

Failed to map C[dec]/[dec]/[dec]/U[dec] to connector [dec] clear connector [dec] [dec] mapping first.

Some 2x2 upstream PHY chips don't support XC crossed connector->receiver mapping C0->R1 + C1->R0. The connector

ubr7200

"Remove all the existing mappings from the two " "connectors of the chip and reprovision the wanted " "mappings. This will rearrang the mappings as " "straight mapping C0->R0 + C1->R1. "

UBR7200-6-CNNR_NORCVR

6-Information

No upstream receiver available in connector group [dec]-[dec] for C[dec]/[dec]/[dec]/U[dec] to connector [dec] mapping

All upstream receivers for the connector group have been used

ubr7200

"Remove some upstream mapping to connectors in the connector group."

UBR7200-3-CNNR_INVALID

3-Error

Connector [dec] and receiver [dec] are not on the same device

The software tries to map an upstream connector on one device to a phy receiver on another device. If this happens in normal operation not through test command it is most likely a

ubr7200

LOG_STD_ACTION

UBR7200-4-ENVM_PS_OVERLOAD

4-Warning

Power supply may be overloaded to support the line card installed in slot [dec]

The power supply may be insufficient to support the number of line \n\ cards installed in the system under certain operation conditions \n\ like high temperature and high voltage margining.

-

"Upgrade the power supply as soon as possible or the system may \n\ fail to operation properly under some certain operation conditions."

UBR7200-6-DPON_CLC_GLOBAL

6-Information

Enabling DPON for MAC domain MD: [chars] implicitly enables DPON for all other

-

-

-

UBR7200-6-MQOS

6-Information

Power supply may be overloaded to support the line card installed in slot [dec]

The power supply may be insufficient to support the number of line \n\ cards installed in the system under certain operation conditions \n\ like high temperature and high voltage margining.

-

"Upgrade the power supply as soon as possible or the system may \n\ fail to operation properly under some certain operation conditions."

UBR7200-6-MD_DS_SG_DCID_CONFLICT

6-Information

Downstream channel IDs conflict in mac-domain of [chars]

At least two channels in the mac-domain have the same downstream channel ID. See show cable fiber-node to see channel ID assignments

-

"Change the downstream channel ID."

UBR7200-6-CGD_AUTO_DCID_UNAVAILABLE

6-Information

Unable to assign an automatic Channel ID for channel in MAC Domain [chars] and Fiber Node [dec]

Unable to assign an automatic Channel ID for the newly added channel in the MAC Domain. See show cable fiber-node to see channel ID assignments in the Fiber-Node.

-

"Attempt to manually resolve channel ID conflict by disabling " "automatic DCID assignment."

UBR7200-6-CGD_AUTO_DCID_PARSE_ERROR

6-Information

Parse error during sync newly assigned automatic DCID \n\ while running CGD command.

A parse error has occured while trying to sync the newly assigned DCID to standby PRE.

ubr7200

"Remove and attempt to add the channel set again."

UBR7200-3-UNEXPECTED

3-Error

[chars]

The specified operation failed.

-

LOG_STD_NO_ACTION

UBR7200-6-CMTS_MD_IDX_OUT_OF_RANGE_ERROR

6-Information

Mac Domain Index [dec] is out of range.

Mac Domain Index is out of range.

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_SLOT_OUT_OF_RANGE_ERROR

6-Information

Slot [dec]/Subslot [dec]/MD [dec] is out of range.

Slot/subslot is out of range.

ubr7200

LOG_STD_NO_ACTION

CMTS-3-LIST_CREATE

3-Error

list create failed for list [chars]

The Cisco CMTS router is unable to create list due to insufficient system memory

cmts

"Run the show memory command to verify available system memory. " "If memory is full contact your Cisco technical support " "representative and provide the representative with the " "gathered information"

CMTS-3-LIST_ENQUEUE

3-Error

list enqueue failed for list [chars]

Unable to enqueue an entry to list

cmts

LOG_STD_ACTION

CMTS-3-LIST_INSERT

3-Error

list insert failed for list [chars]

The Cisco CMTS router is unable to insert an entry into list due to insufficient system memory or insert an exist entry

cmts

"Run the show memory command to verify available system memory. " "Then run the show logging command to view all system-logged " "messages. If memory is full contact your Cisco technical " "support representative and provide the representative with " "the gathered information"

UBR7200-7-PHY_CLK_MIS_DET_MSG

7-Debug

Clock misalignment detected on phy [dec]:\nIOS det count=[dec] bad DV count=[dec] total DV count=[dec] old cal data=0x%02x new cal data=0x%02x\n[chars]

A phy clock misalignment has been detected and corrected.

ubr10000

LOG_STD_NO_ACTION

CMTS-3-MCAST_SES_MISMATCH

3-Error

Session Request Response Mismatch for transaction ID [dec] session [chars][chars] CM [enet]

Response from the LC does not match the session requested for.

cmts

LOG_STD_ACTION

UBR7200-4-TLV56_CONFLICT_CHANNEL_SET

4-Warning

Confilct with TLV56 and channel set. Either remove TLV56 from the CM config file or adjust the power plant. CM Mac Addr <[enet]> may go offline due to high power.

Registration Failed Check TLV56 Configuration Setting\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CM_RNG_CLASS_ID_UNMATCH

6-Information

US that CM [enet] send Initial Rng Req has unmatched Channel Class ID0x[hec] with CM's Ranging Class ID0x[hec]\n

CM's Ranging Class ID doesn't match the the Channel Class ID of its upstream but it may be expected due to CM received a DCC/DBC... or CM config file included extended Ranging Class ID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-DOCSIS_SID_DELETE_IPC_ERROR

6-Information

RP try to delete cm from LC's host_db mac [enet] sid [dec] host_hdl flag [hec] device_class [chars]

RP send IPC to LC to delete cm from LC's host_db which is not allowed. RP may treat a CM as CPE\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_CM_DB_CM_ADD_ERROR

6-Information

[chars] CM [enet] cminstp %p prim_sid [dec] prim sidinstp %p check failed when add to DB

cable modem check error when add to DB

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_CM_DB_SID_DUPLICATE_ERROR

6-Information

[chars] multiple prim_sid assignment for CM [enet] previous prim_sid [dec] current prim_sid [dec]

prim SID already exist when CMTS try to assign a new SID to cable modem

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_CM_DB_SID_CHECK_ERROR

6-Information

[chars] CM_DB: PRIM_SID ERROR CM [enet] cminstp->prim_sid [dec] \n sidinstp->prim_sid [dec] sidinstp->sidinstp [dec]

PRIM SID check error whe add to CM DB

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_CM_DB_CM_SID_INCONSISTENCY_ERROR

6-Information

CM_DB's mac_domain [chars] \n cminstp's mac_domain [chars] CM_DB's cminstp %p current cminstp %p CM_DB's sidinstp %p current sidinstp %p\n CM_DB's mac_addr [enet] cminstp's mac_addr [enet] sidinstp's mac_addr [enet]\n CM_DB's prim_sid [dec] cminstp's prim_sid [dec] sidinstp's prim_sid [dec]

find cable modem's info is consistent with prim sid

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_CM_DB_ACCESS_DENIAL_ERROR

6-Information

[chars] try to access CM [enet] when prim sid is deleted

access cable modem after prim sid is not allowed

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_CM_DB_DELETE_TIMING_ERROR

6-Information

[chars] CMTS delete CM [enet] cminstp %p but prim_sid [dec] prim_sidinstp %p is not deleted

CM deletion should not before prim_sid deletion

ubr7200

LOG_STD_NO_ACTION

UBRSNMP-0-SNMP_SET_IPC

0-Emergency

Schooner SNMP SET[dec]/[dec] [chars] failed

SNMP SET failed due to either IPC failure or line card SET failed

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-4-MSGVERSION

4-Warning

Incompatible message version with slot [dec]

There is incompatibility between the the message version being sent by the line card and the message version used by the RP/NPE. This type of incompatibility could happen if the RP/NPE and line card are using different IOS versions due to an RP/NPE oir event

ubr7200-sw

"A microcode reload will solve the problem. "

UBR7200IPC-3-IPCERR

3-Error

IPC message error [dec]

Error from IOS IPC layer on linecard Port API port

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-3-IPCOPENFAIL

3-Error

slot [dec]: could not open IPC port for port id %08x

IPC port open to mcu card failed - indicates that the card is down or there is a transient failure

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-3-LC_OBJERR

3-Error

[chars]

A card IPC API object is not supported

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-3-LC_DEFOBJ

3-Error

Default linecard object invoked for type [dec]

The default card IPC API object was invoked since there was no registered handler for that object

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-1-DISCOVER_ENET

1-Alert

Failed to init Ethernet device [dec]

The software could not initialize

ubr7200-sw

"Power down reseat the interface card " "and reboot. If the message recurs call your " "technical support representative for assistance."

UBR7200IPC-1-DISCOVER_SAR

1-Alert

Failed to init SAR device [dec]

The software could not initialize

ubr7200-sw

"Power down reseat the interface card " "and reboot. If the message recurs call your " "technical support representative for assistance."

UBR7200IPC-4-PCIVALID

4-Warning

PCI activation failed slot [dec] 0x[hec]

The system received an invalid PCI signal from the port adapter. This is probably due to a hardware failure.

ubr7200-sw

"Refer to the configuration guidelines for the maximum allowed " "high and medium bandwidth port adapters for the system."

UBR7200IPC-2-BADSLOT

2-Critical

Out of range card slot index[dec]

The software specified an out-of-range card slot index.

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-2-BADSLOTSUBSLOT

2-Critical

Out of range card slot/subslot pair[dec]/[dec]

The software specified an out-of-range card slot/subslot pair.

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-2-BADINTERFACE

2-Critical

Out of range Card interface [dec] on slot [dec]

The software specified an out-of-range card interface.

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-2-BADRSRCNUM

2-Critical

Invalid resource number from PXF [dec]. PLEASE REPORT THIS!

The PXF hardware diversion path specified a bad resource number.

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-3-DEACTIVATED

3-Error

card in slot [[dec]/[dec]] disabled.

The card is being deactivated.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

UBR7200IPC-2-CARDRECUR

2-Critical

Recursive loop while getting the daughtercard info for card type [dec]

While getting the daughter card info for the chassismib the platform snmp code goes into an infinite loop.

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-2-CARDTYPEERROR

2-Critical

card in slot [[dec]/[dec]] is of incorrect type 0x[hec]

The card is of wrong type allowed in that slot

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-1-UNKEVT

1-Alert

Subsystem unknown event:[dec] in [chars] for interface [chars]

Subsystem received unknown event type.

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-1-SNMP_GETINDEX_FAIL

1-Alert

Cannot get SNMP physical Index for [chars]

LC System initialization failure.

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-6-CM_INCONSISTENCY

6-Information

CM state inconsistency [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received INIT_CM for an online CM Copy the message and report to your technical support representative

ubr7200-sw

LOG_STD_ACTION

IPCOIR-2-CREATEFAIL

2-Critical

Couldn't create [chars]

Could not create specified resource

ubr7200-sw

"Contact customer support."

IPCOIR-3-BADLCAPI

3-Error

Incorrect API message version 0x[hec]

The linecard and IOS images are badly out of phase.

ubr7200-sw

"Contact customer support."

IPCOIR-3-BADMESSVER

3-Error

Incorrect message version obj 0x[hec] op 0x[hec] version 0x[hec]

The linecard and IOS images are badly out of phase.

ubr7200-sw

"Contact customer support."

IPCOIR-5-CARD_DETECTED

5-Notice

Card type [chars] 0x[hec] in slot [dec]/[dec]

A card was detected in the indicated slot.

ubr7200-sw

LOG_STD_NO_ACTION

IPCOIR-3-CARD_BADIDPROM

3-Error

Card in slot [dec]/[dec] has an invalid card type in IDPROM

The linecard IDPROM is unprogrammed or has failed.

ubr7200-sw

"Contact customer support."

IPCOIR-3-CARD_UNSUPPORTED

3-Error

Unsupported card type 0x[hec] in slot [dec]/[dec].

The linecard is not supported by this version of IOS

ubr7200-sw

"Contact customer support."

IPCOIR-2-CARD_UP_DOWN

2-Critical

Card in slot [dec]/[dec] is [chars]. Notifying [chars] driver.

Notification of a Line Card coming Up or Down.

ubr7200-sw

LOG_STD_NO_ACTION

IPCOIR-5-CARD_LOADING

5-Notice

Loading card in slot [dec]/[dec]

Notification of a Line Card download with MD5 data.

ubr7200-sw

LOG_STD_NO_ACTION

IPCOIR-3-CARD_GET_VERSION_RESPONSE

3-Error

Unsolicited response from slot [dec]/[dec] oir_state = [chars]

Unexpected message from a Line Card.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-IPC_GET_MSG_BUF_FAIL

3-Error

Unable to get an IPC msg buffer in [dec] tries: slot [dec]/[dec]

The IOS IPC buffer pool was empty for a sustained period of time.

ubr7200-sw

"Install more processor SDRAM in the PRE."

IPCOIR-4-IPC_GET_MSG_BUF

4-Warning

Get IPC msg buf failed [dec] times: slot [dec]/[dec] - retry in [dec] sec

The IOS IPC buffer pool was temporarily empty.

ubr7200-sw

"Consider installing more processor SDRAM in the PRE."

IPCOIR-3-LOADER_IPC_FAIL

3-Error

IPC failed [chars] [chars] slot [dec]/[dec]

The IOS IPC protocol reported an unexpected error.

ubr7200-sw

"Make sure the indicated card is still plugged in."

IPCOIR-3-LOADER_SERVER_FAIL

3-Error

Remote server refused to load slot [dec]/[dec]

Unable to load a Line Card. Load will be attempted again.

ubr7200-sw

LOG_STD_ACTION

IPCOIR-3-STATE_MACHINE_BUG

3-Error

card_oir_loading called should never happen recovering.

An internal software error occurred. Will recover.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-STATE_MACHINE_BUG2

3-Error

card_oir_insert_card: already have 0x[hec] removing.

An internal software error occurred.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-BADIPHOST

3-Error

Bad IP address or host name [chars]

The IP address or host name is incorrect or unknown.

ubr7200-sw

"Check the IP address or hostname."

IPCOIR-3-TFTPFAIL

3-Error

TFTP of [chars] from [chars] failed...\n

The indicated image is inaccessible

ubr7200-sw

"Check file permissions network connectivity."

IPCOIR-3-FLASHFAIL

3-Error

Couldn't load [chars]...\n

The indicated image is inaccessible

ubr7200-sw

"Check the filename."

IPCOIR-3-BOGUSCARD

3-Error

Bogus cardtype [dec]

The indicated cardtype is unknown to the software.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-4-REPEATMSG

4-Warning

IPC handle already exists for [dec]/[dec]

IPC communication between the NPE and a Line Card already setup

ubr7200-sw

"Reload the specified linecard. If the message recurs call your " "techical support representative for assistance."

IPCOIR-3-WRONGCARDTYPE

3-Error

Wrong card type in slot [dec]/[dec].

IPC message reporting wrong card type received from an operational card.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-CARDCRASH

3-Error

Card crashed in slot [dec]/[dec].

IPC message reporting wrong version received from an operational card.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-TIMEOUT

3-Error

Timeout waiting for a response from slot [dec]/[dec].

NPE lost connection with a Line Card. Line Card might have crashed.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-IMAGEVERSION

3-Error

Image version stamp missing

The loaded image did not contain a recognizable version stamp

ubr7200-sw

"Replace the image with known-good bits and try again."

IPCOIR-3-LOADER_DNLD_REJECT

3-Error

Buffer download to slot [dec]/[dec] rejected

The linecard buffer download server rejected the download.

ubr7200-sw

LOG_STD_ACTION

IPCOIR-3-LOADER_DNLD_NOBUF

3-Error

Buffer allocation failed

The buffer downloader couldn't allocate a message buffer.

ubr7200-sw

"Reboot the chassis."

IPCOIR-3-CRE_INIT_FAIL

3-Error

Unable to initialize PRE ports.

The PRE plugin init sequence failed.

ubr7200-sw

"Determine and fix cause."

IPCOIR-3-PLUGIN_INIT_FAIL

3-Error

Unable to create driver plugin in slot [dec]/[dec].

A valid linecard driver plugin create failed.

ubr7200-sw

"Perhaps a memory allocation failure should not happen."

IPCOIR-2-PLUGIN_PREANALYZE_FAIL

2-Critical

Unable to preanalyze driver plugin in slot [dec]/[dec].

A valid linecard driver preanalyze failed.

ubr7200-sw

"Possibly incompatible card types"

IPCOIR-2-NULL_PTR

2-Critical

[chars]: pointer is null

Unexpected NULL pointer to a data structure.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

IPCOIR-3-KEEPALIVE

3-Error

A keepalive timeout occurred on slot [dec]/[dec].\n Last process: [chars] 4ms time = [dec]ms Intr. Busy Count: [dec] Sched Flag Count: [dec]

The line card has stopped responding to keepalive polls while in the RUN state. The attached debug information was provided by the line card.

ubr7200-sw

"Monitor the LC for a persistent problem. Keep the console log of " "each occurrence and if the problem occurs again forward the log to " "Cisco."

IPCOIR-3-LCCRASH

3-Error

The card in slot [dec]/[dec] has crashed. Cause Register: 0x%0x Signal: %0u

The line card in the specified slot has crashed.

ubr7200-sw

"Wait for the LC to come back up then connect to the remote console and " "extract the crashinfo file from bootflash. Forward the file the " "output from a show tech command and the NPE console log to Cisco."

IPCOIR-6-LCWAITINFO

6-Information

CLC [dec]/[dec]> [chars]

The NPE OIR handler received a console error message from a distributed line card while in the crashwait state. The handler enters this state when it detects a Keepalive timeout on a distributed line card. During the crash wait period the LC is expected to collect and store crash information. At the end of the wait period the NPE will reload the LC. During this time it's possible that the LC will try to send error messages to it's console. Normally these would be sent to the NPE via the logger. However during the wait period the IPC link between the NPE and the LC is down so the OIR debug code provides a rudimentary method of collecting and displaying these messages

ubr7200-sw

"Report the problem to Cisco. Include the log messages along with the " "output of the show tech command and crashinfo file from the LC."

IPCOIR-3-LC4MS

3-Error

The watchdog timer on slot [dec]/0 has stopped.

The line card has stopped servicing it's watchdog timer.

ubr7200-sw

"The condition may be temporary or may be caused by a crash. " "Check the LC's bootflash for crashinfo files and monitor " "the LC for a watchdog timeout."

UBR7200IPC-3-PLUGIN_UNKNOWN

3-Error

Unknown card type [hec] in slot [dec]/[dec].

The card in the specified slot is not a known type.

ubr7200-sw

LOG_STD_ACTION

UBR7200IPC-3-UNEXP_INTR

3-Error

Interrupt [chars] not expected masking off

An interrupt of a certain type was signalled but the interrupt handler for this type of interrupt is not yet installed.

ubr7200-sw

"This problem should be self-correcting but indicates either " "a hardware or a software defect. If it's a hardware defect " "further problems are to be expected. If it's a software " "problem certain types of error and alarm conditions may be " "left undetected.\n" "Copy the error message exactly as it appears and report it to your " "technical support representative."

IPCGRP-3-INVNUM

3-Error

[chars] [dec]

-

-

-

IPCGRP-3-SEATERR

3-Error

[chars] [dec]

The ID associated with an IPC card is either missing duplicated or cannot be created.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-CARDERR

3-Error

[chars]

An IPC card has registered itself to the IPC master twice. The card malfunctioned and its IPC is not active.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-MSGERR

3-Error

[chars] [dec]

The slave IPC cannot register with master. It cannot exchange messages with the master.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-CMDOP

3-Error

IPC command [dec] slot[dec]/[dec]: [chars]

IPC command processing operational errors.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-EVENTOP

3-Error

Event [dec] from slot[dec]/[dec]: [chars]

IPC event processing operational errors.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-INVALID_PARAMS

3-Error

Invalid interface[dec]/[dec]/[dec]

Invalid interface addressed by the corresponding IPC message.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-NOHWIDB

3-Error

Cannot find hwidb for interface[dec]/[dec]

Interface identifier does not exist for the interface addressed by the corresponding IPC message.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-SYSCALL

3-Error

System call for command [dec] slot[dec]/[dec] : [chars] Cause: [chars]

-

-

-

IPCGRP-3-NULLMSG

3-Error

Null [chars] ipc message

An empty IPC message which is not expected to be received.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-NBLKCMD

3-Error

[chars]

Nonblocking IPC command queue initialization failure.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-6-NBLKCMD_Q_FULL

6-Information

Nonblocking IPC command queue full [dec] commands

-

-

-

IPCGRP-3-NULLREXECCMD

3-Error

Received empty ipc rexec cmd message

REXEC-On IPC command failure.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-REXEC

3-Error

[chars]

REXEC-On IPC command failure.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-EXECCMDMSG

3-Error

Incorrect msg size size=[dec]

Wrong size of a REXEC-On IPC command.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-CREATE_FAIL

3-Error

[chars] [chars]

Failed to create IPC port on RP.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-ERROR

3-Error

[chars]: [chars]

An IPC error was detected

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-3-NOACK

3-Error

Access to [chars] temperature sensor failed

Accesses to chassis temperature sensor failed.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

UBR7200IPC-4-TEST

4-Warning

Test command no. [dec] executed by user

Test command is executed by user.

ubr7200-sw

LOG_STD_NO_ACTION

UBR7200IPC-3-INITFAIL

3-Error

[chars] - initialization of interface failed

Initialization of the specified interface failed.

ubr7200-sw

LOG_STD_SH_TECH_ACTION

UBR7200IPC-3-CLI_CMD

3-Error

[dec]/[dec]: CLI cmd failed in function [chars]

Most likely S/W failure

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-3-IPCFAIL

3-Error

[chars]: IPC command [chars] to interface failed in [chars]

System IPC initialization failure.

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-0-CLI_CONFIG

0-Emergency

CMTS[dec]/[dec]/[dec] schrp_cli_cmd failed in [chars]

Most likely S/W failure

ubr7200-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200IPC-2-CLI_UNSUPPORTED_CMD

2-Critical

cable modem <ipaddr/macaddr> cmd not supported on MC28U

Currently unsupported command

ubr7200-sw

LOG_STD_NO_ACTION

UBR7200IPC-3-CLI_IPC_MALLOC

3-Error

Memory allocation request failed in [chars]

Couldn't allocate memory for distributed CLI operation

ubr7200-sw

"Use the show memory command to analyze memory usage."

IPCGRP-3-ENQFAIL

3-Error

enqueue failed! queue:[chars] size:[dec]

process_enqueue failed.

ubr7200-sw

LOG_STD_ACTION

IPCGRP-3-LOADQUACKFAIL

3-Error

slot [dec] load quack data failed!

load quack data failed.

ubr7200-sw

LOG_STD_ACTION

DSG-6-LIST_ERR

6-Information

[chars] [dec]

Infomational only

ubr7200

LOG_STD_NO_ACTION

DSG-6-NAME_RESOLVED

6-Information

hostname <[chars]> is resolved as <[inet]>

DNS query for a hostname is successful.

cmts-application

LOG_STD_NO_ACTION

DSG-5-NAME_CHANGED

5-Notice

hostname <[chars]> is changed from <[inet]> to <[inet]>

IP address of a hostname is changed.

cmts-application

LOG_STD_NO_ACTION

DSG-5-NAME_UNRESOLVED

5-Notice

hostname <[chars]> cannot be resolved

DNS query for a hostname is not successful.

cmts-application

LOG_STD_NO_ACTION

DSG-6-CFR_APPLIED

6-Information

classifier <[chars]> is applied successfully

classifier is applied successfully.

cmts-application

LOG_STD_NO_ACTION

DSG-5-CFR_NOT_APPLIED

5-Notice

classifier <[chars]> cannot be applied because of errors

classifier cannot be applied because of errors.

cmts-application

LOG_STD_NO_ACTION

DSG-6-CFR_UPDATED

6-Information

classifier <[chars]> is updated

classifier is updated

cmts-application

LOG_STD_NO_ACTION

DSG-5-CFR_CONFLICT

5-Notice

classifier <[chars]> is put into conflict state because of errors

classifier is already applied but we cannot update the classifier with changed destination IP address or source IP address because of errors. So we put the classifier into conflict state.

cmts-application

LOG_STD_NO_ACTION

DSG-5-ILLEGAL_MCASTADDR

5-Notice

IP address <[inet]> is not a multicast address or is a reserved multicast address

IP address is not an multicast address or is a reserved multicast address

cmts-application

LOG_STD_NO_ACTION

DSG-5-ILLEGAL_SOURCEADDR

5-Notice

IP address <[inet]> is an illegal source address

IP address is an illegal source address

cmts-application

LOG_STD_NO_ACTION

DSG-5-SSM_SOURCE_ZERO

5-Notice

destination IP address is <[inet]> in SSM range source IP address cannot be zero

dest-ip is in SSM range src-ip cannot be zero

cmts-application

LOG_STD_NO_ACTION

DSG-5-SSM_SOURCE_PREFIX

5-Notice

destination IP address is <[inet]> in SSM range source IP address prefix length must be [dec]

dest-ip is in SSM range src-ip prefix length should match

cmts-application

LOG_STD_NO_ACTION

DSG-5-MAC_ADDR

5-Notice

cfr [dec] and cfr [dec] have the same destination IP address [inet] but different MAC addresses [enet] and [enet]

two cfrs have the same destination IP address but different MAC addresses

cmts-application

LOG_STD_NO_ACTION

DSG-5-SOURCE_LEN

5-Notice

cfr [dec]: source IP address [inet] and source prefix length [dec] don't match

source IP address and source prefix length of the cfr don't match

cmts-application

LOG_STD_NO_ACTION

DSG-5-IDENTICAL_CFR

5-Notice

cfr [dec] and [dec] are identical

two cfrs are identical

cmts-application

LOG_STD_NO_ACTION

DSG-5-SEMAPHORE_ERROR

5-Notice

failed to obtain the DSG semaphore

failed to get the semaphore

cmts-application

LOG_STD_NO_ACTION

DSG-5-CFRRMTUNNEL

5-Notice

cfr [dec] becomes unresolved it will be removed from the tunnel it belongs to

cfr becomes unresolved it will be removed from the tunnel it belongs to

cmts-application

LOG_STD_NO_ACTION

DSG-5-STATICJOINERR

5-Notice

cfr [dec] cannot be enabled because there already exists a non-DSG static join for S [inet] or * [inet] in interface [chars]

cfr cannot be enabled because there already exists a non-DSG static join for the multicast group

cmts-application

LOG_STD_NO_ACTION

DSG-5-DSG_INFO_DB_LOOKUP_FAILURE

5-Notice

Faild to find the entry from the DSG Info DB for [chars] [chars] [chars]

DSG Info DB lookup failure

cmts-application

LOG_STD_NO_ACTION

GIGASTACK-3-INIT_FAILURE

3-Error

Gigastack GBIC in [chars] initialization failed.

Gigastack GBIC failed POST.

firmware

"Remove the Gigastack GBIC and re-insert it into the GBIC slot."

GIGASTACK-6-LOOP_DETECTED

6-Information

Gigastack GBIC in [chars] is selected as Master Loop Breaker. \nLink 2 of the Gigastack GBIC is disabled to break the loop.

Loop is detected in the Gigastack and this Gigastack GBIC is selected as the Master Loop Breaker. Link 2 of this Gigastack GBIC is disabled to break the loop.

-

LOG_STD_NO_ACTION

GIGASTACK-6-LOOP_BROKEN

6-Information

Link loss is detected in the Gigastack loop \nLink 2 of the Gigastack GBIC in [chars] is re-enabled.

Loop formed by Gigastack modules is broken because of link loss. Link 2 of the Master Loop Breaker is re-enabled to replace the broken link

-

LOG_STD_NO_ACTION

GIGASTACK-1-NO_LOOP_DETECT

1-Alert

The link neighbor of link [dec] of Gigastack GBIC in [chars] did not respond to the loop detection request. If loop topology is deployed make sure all switches in the stack are running the latest software.\n

No acknowledgement for Gigastack loop detection request is received from one of the links on a Gigastack GBIC. Either the neighboring switch does not support Gigastack Loop breaking algorithm or the link between the two Gigastack GBICs is broken. Under this condition a Gigastack loop topology will not be automatically detected and the connectivity between switches in the stack could be lost.

-

"If loop topology is used in the Gigastack make sure the latest software is running on all switches in the stack. Check the Gigastack GBICs involved to make sure they are functioning."

GBIC-6-SERDES_SERIAL_INV_DATA

6-Information

Unrecognizable GBIC found in [chars] serial data 0x%02x

The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC.

firmware

"If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch."

GBIC-6-SERDES_MODULE_UNKNOWN

6-Information

Unrecognizable GBIC found in [chars] module mask 0x%02x

The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC.

firmware

"If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch."

GBIC-4-NOREAD_VSDATA

4-Warning

Unable to read vendor-specific data for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read identifying vendor-specific information to verify its authenticity.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

GBIC-4-UNRECOGNIZED_EXTTYPE

4-Warning

GBIC interface [chars] has unrecognized extended type

The GBIC was identified as a Cisco GBIC but the system does not recognize its reported extended type code.

firmware

"Check the list of supported GBICs for this version " "of the system software. An upgrade may be required " "for newer GBICs. Even if unrecognized the GBIC " "may still operate properly perhaps with limited " "functionality."

GBIC-4-NOREAD_VNAME

4-Warning

Unable to read vendor name for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read the name of the GBIC's vendor.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

GBIC-4-NOREAD_VSERNUM

4-Warning

Unable to read serial number for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read the GBIC's serial number.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

GBIC-4-XCVR_INTERR

4-Warning

Internal error occurred in setup for GBIC interface [chars]

The system could not allocate resources or had some other problem in the setup for the specified GBIC interface.

firmware

"Reload the system. If the problem persists " "contact TAC."

GBIC-4-CHECK_SUM_FAILED

4-Warning

GBIC EEPROM data check sum failed for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read vendor-data information to verify its correctness.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

PLATFORM_CAT2950-3-ASIC_INIT_FAILURE

3-Error

\nAsic driver initialization has failed\n

One of the ASIC initialization steps has failed. This could be a failure in the PCI configuration setup I2C initialization Build-in self test on the internal chip memories or other miscellaneous initialization steps due to a hardware defect.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-SYSTEM_INFO_FAILURE

3-Error

\n The board information could not be read correctlyinitialization failed

During switch driver initialization there was a failure to read the system board information. This could be a hardware problem.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-MEM_INIT_FAILURE

3-Error

\n The switch memory resources could not be allocated for [chars] initialization failed

During the switch driver initialization driver-related memory resources could not be allocated. This could be a hardware defect.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-PCI_FIND_FAILURE

3-Error

\n The number of asics expected were [dec] PCI bus scan found [dec]\n

During the switch driver initialization incorrect number of ASICs were found on the PCI bus or no ASICs with a correct PCI value was found. This could be caused by a system PCI bus defect or incompatible software version running on the switch.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-PCI_INIT_FAILURE

3-Error

\n The PCI address space initialization failed

During the switch driver initialization the PCI address space for the ASIC could not be initialized. This could be a system PCI-bus-related issue.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-PCI_TEST_FAILURE

3-Error

\nPCI address space test failedWrote 0x[hec] read 0x[hec] re-read 0x[hec]\n

During the Power-On Self Test it is found that the PCI address space for the ASIC has not been mapped correctly. This could be a system PCI-bus-related issue.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-ASIC_BIST_FAILURE

3-Error

\n C2950 BIST failed for memory [chars] count [dec]\n

During the Power-On Self Test the Built-In memory test on the internal chip memories has failed. This could be due to an ASIC defect.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-GBP_INIT_FAILURE

3-Error

\n GBP currently FULL or UNAVAILABLE.

During the switch driver initialization an error has been detected in the external packet memory. This could be a defect in the ASIC or in the external SDRAM.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-MEM_READ_FAILURE

3-Error

\n Read memory failed for memory [chars] at index [dec]\n

An attempt to read a valid location in the internal chip memory was failed. This could be due to a hardware defect.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-MEM_WRITE_FAILURE

3-Error

\n Write memory failed for memory [chars] at index [dec]\n

An attempt to write to a location in the internal chip memory was failed. This might be cause by writing to a invalid memory location or a defect in the hardware.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-SCHAN_OP_FAILURE

3-Error

\n S-channel operation timeout for opcode [chars]\n

This message means that there was a failure to read or write to an ASIC register or a memory location because of an ASIC internal bus failure.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-SCHAN_READ_REG_FAILURE

3-Error

\n S-channel operation read register failure at addr [hec]\n

This message means that there was a failure to read a ASIC register which might be caused by an invalid register address or an internal bus failure.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-MIIM_OP_FAILURE

3-Error

\n Unable to read PHY register at addr [hec] for phy id [hec]\n

This message means that there was a failure to read from or write to a PHY register on the switch. This could be caused by a defect in the MII/GMII interface of the switch.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-GBP_FAILURE

3-Error

\n Unable to initialize the external packet memory \n

During the switch driver initialization there was an error in the external packet memory initialization. This could be a defect in the ASIC or in the external SDRAM.

-

LOG_STD_ACTION

PLATFORM_CAT2950-3-MEM_COPY_FAILURE

3-Error

\n Invalid copy [dec] for table [chars]\n

This message means that there was an attempt to read or write an invalid copy of the switch internal memory. This is a recoverable error but should not happen.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-MEM_INDEX_FAILURE

3-Error

\n Invalid index [dec] for table [chars]\n

This message means that there was an attempt to access an invalid index of the switch internal memory. This is a recoverable error but should not happen.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-REG_READ_FAILURE

3-Error

\n Register read failed for register [chars] in [chars]\n

An attempt to read a valid location in the internal chip register failed. This could be due to a hardware defect.

-

LOG_STD_RECUR_ACTION

PLATFORM_CAT2950-3-REG_WRITE_FAILURE

3-Error

\n Register write failed for register [chars] in [chars]\n

An attempt to write to a location in the internal chip register failed. This might be cause by writing to a invalid register location or a defect in the hardware.

-

LOG_STD_RECUR_ACTION

STORM_CONTROL-2-SHUTDOWN

2-Critical

Storm control shut down [chars]

Excessive traffic has been detected on a port that has been configured to be shutdown if a storm event is detected.

-

"Once the source of the packet storm has been fixed reenable " "the port using port configuration command."

C2950_MONITOR-3-C2950MONITOR_UNKNOWN_PARAM

3-Error

Unknown trap type:[dec] received in emt_call function.

Unknow trap type. Some feature requires this trap type to be handled

-

-

ENVIRONMENT-2-FAN_FAULT

2-Critical

System Fault: FAN FAULT is detected.

-

-

-

ENVIRONMENT-4-CONFIG_OVERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the configured threshold but less or equal to the max inside temperature

-

-

ENVIRONMENT-3-OVERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the max temperature threshold

-

-

ENVIRONMENT-3-UNDERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the min temperature threshold

-

-

ENVIRONMENT-3-RPS_FAILED

3-Error

[chars] [chars] [chars] [chars]

Only one power supply was detected for system in dual power mode or power supply is failing

-

-

ETHCNTR-3-LOOP_BACK_DETECTED

3-Error

Keepalive packet loop-back detected on [chars].

Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network.

firmware

"Correct the problem causing the loopback " "condition. Then bring the port up by entering the shutdown " "then no shutdown interface configuration commands. The port " "will be automatically restarted after a timeout if errdisable " "recovery cause loopback is configured."

ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD

3-Error

Half-duplex loopback detected collision threshold exceeded on [chars].

The collisions on a half-duplex port exceeded the threshold with no valid data packets. The port is considered to be in a loopback condition. This may be caused by accidentally plugging a balun cable into the port

firmware

"Correct the problem causing the " "loopback condition. Then bring the port up by entering " "the shutdown then no shutdown interface configuration " "commands. The port will be automatically restarted " "after a timeout if errdisable recovery cause loopback " "is configured."

HWMATM_MOD-3-NULLPTR

3-Error

Unexpected null pointer in [chars] at [dec]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

DOT1X_MOD-3-NULLPTR

3-Error

Unexpected null pointer in [chars] at [dec]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_STRUCT

1-Alert

Could not initialize structure

The driver failed to initialize a structure

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_POOL

1-Alert

Could not init buffer pools

The driver failed to get a pool of buffers from IOS

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_IDB

1-Alert

Invalid Interface Descriptor Block

The driver tried to fetch the interface's IDB and failed

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_MEDIA

1-Alert

Unknown media-type in subblock

The media-type specified in the driver subblock is invalid

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_PLUGIN

1-Alert

Plugin function table incomplete or missing

The driver could not access the PA's specific function table

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_PARTICLE

1-Alert

Problem getting particle size

The driver was unable to get the particle size for this interface

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-MODE_INVALID

1-Alert

Unknown or invalid chip mode MII/TBI

The driver subblock contains an invalid or undefined chip operating mode MII or TBI mode

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-IDBTYPE_UNK

1-Alert

Unknown IDBTYPE while starting driver

The IDBTYPE in the interface's instance structure is undefined for this driver

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_SB_NOMEM

1-Alert

[chars] - Cannot create IDB subblock due to insufficient memory

There was insufficent system memory to create the subblock.

high-gig-ethernet

"The router requires more main memory." LOG_STD_SH_TECH_ACTION

dtsec-1-BAD_SUBBLOCK

1-Alert

[chars] - Could not install or use IDB subblock

An internal IOS error prevented the IDB subblock from being installed or used.

high-gig-ethernet

"Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION

dtsec-1-INITFAIL_NOMEM

1-Alert

[chars] initialization failed no buffer memory

The Ethernet port initialization failed due to insufficient memory

high-gig-ethernet

"The router requires more packet memory - consider upgrade." LOG_STD_RECUR_ACTION

dtsec-3-ERRINT

3-Error

[chars] error interrupt mac_status = 0x%016llx

The MAC controller has signalled an error condition.

high-gig-ethernet

LOG_STD_ACTION

dtsec-2-NOISL

2-Critical

Interface [chars] does not support ISL

ISL is not supported on the specified interface's hardware.

-

LOG_STD_NO_ACTION

dtsec-3-TOOBIG

3-Error

[chars] packet too big [dec] from [enet]

The interface detects a packet larger than what is defined by MTU

high-gig-ethernet

"Check the other station's MTU setting" LOG_STD_NO_ACTION

dtsec-1-RESET

1-Alert

MAC Still in Reset

An attempt was made to access the MAC while it was in reset

high-gig-ethernet

LOG_STD_SH_TECH_ACTION

dtsec-3-MAC_LIMIT_EXCEEDED

3-Error

Unable to add mac address [enet]

Max number of allowed mac entries reached. Cannot add any more.

-

"Try removing some of the own mac addresses for example used by each" "unique hsrp group configuration. standby use-bia could be used to " "limit the usage"

dtsec-3-UNKNOWN_GBIC

3-Error

[chars] - Unknown GBIC type

Interface contains a GBIC of unknown type. This causes the link to be down.

high-gig-ethernet

"Please make sure the GBIC type is compatible with the interface. " "Verify that the GBIC was obtained from Cisco or a supported vendor"

dtsec-3-BAD_GBIC_EEPROM

3-Error

[chars] - GBIC contains a bad EEPROM

Interface contains a GBIC with a bad EEPROM. This causes the link to be down.

high-gig-ethernet

"Please make sure the GBIC type is compatible with the interface. " "Verify that the GBIC was obtained from Cisco or a supported vendor"

dtsec-3-NOT_SUPPORTED

3-Error

[chars] - unsupported GBIC

The GBIC module for the interface specified in the error message is not a Cisco-supported module. As a result of the error the module is disabled.

high-gig-ethernet

"Replace the module with a Cisco-supported GBIC. If the problem " "persists LOG_STD_ACTION."

dtsec-3-DUPLICATE

3-Error

[chars] - duplicate GBIC

The GBIC module for the interface specified in the error message is a duplicate of another GBIC in the system. As a result of the error both modules are disabled.

high-gig-ethernet

"Remove the duplicate module. If the problem persists LOG_STD_ACTION."

RADIAN-3-CMIC_FAIL

3-Error

Radian [dec] CMIC register [chars] fail for [chars] rc = [dec]

Radian CMIC register read or write operation failure

cmts-platform-infr

LOG_STD_SH_TECH_ACTION

RADIAN-3-SCHAN_FAIL

3-Error

Radian [dec] SCHAN [chars] fail for [chars] rc = [dec]

Radian S-Channel read or write operation failure

cmts-platform-infr

LOG_STD_SH_TECH_ACTION

RADIAN-5-MMU_INTR_MSG

5-Notice

Radian slot/unit [dec]/[dec] MMU INTR: [chars]

Radian MMU minor ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-3-MMU_INTR_ERR

3-Error

Radian slot/unit [dec]/[dec] MMU ERR INTR: [chars]

Radian MMU ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-5-IL_INTR_MSG

5-Notice

Radian slot/unit [dec]/[dec] IL INTR: [chars]

Radian IL minor ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-3-IL_INTR_ERR

3-Error

Radian slot/unit [dec]/[dec] IL ERR INTR: [chars]

Radian IL ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-5-PE_INTR_MSG

5-Notice

Radian slot/unit [dec]/[dec] PE INTR: [chars]

Radian PE minor ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-3-PE_INTR_ERR

3-Error

Radian slot/unit [dec]/[dec] PE ERR INTR: [chars]

Radian PreEnqueue ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-5-PD0_INTR_MSG

5-Notice

Radian slot/unit [dec]/[dec] PD0 INTR: [chars]

Radian PostDequeue minor ERROR0 interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-5-PD1_INTR_MSG

5-Notice

Radian slot/unit [dec]/[dec] PD1 INTR: [chars]

Radian PostDequeue minor ERROR1 interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-5-XLPORT_INTR_MSG

5-Notice

Radian slot/unit [dec]/[dec] XLPORT INTR: [chars]

Radian XLPORT minor ERROR interrupt occurs

cmts-platform-infr

LOG_STD_ACTION

RADIAN-3-VLI_SWITCHOVER_TIMEOUT

3-Error

Haba VLI switchover: wait [chars] timeout

Haba switchover timeout

cmts-platform-infr

LOG_STD_ACTION

RADIAN-5-VLI_SWITCHOVER_MSG

5-Notice

Haba VLI switchover: [chars] in [dec]ms

Haba switchover message

cmts-platform-infr

LOG_STD_ACTION

RADIAN-2-IL_SYNC_ERR

2-Critical

[chars] Radian IL sync/align error [chars]

Radian IL sync or align error with Cobalt4 IL

cmts-platform-infr

LOG_STD_ACTION

RADIAN-3-VLI_ACCESS_ERR

3-Error

VLI Err: [chars]

Radian VLI access error

cmts-platform-infr

LOG_STD_ACTION

RADIAN-3-INIT_FAIL

3-Error

[chars] for slot: [dec] unit: [dec] rc: [dec]

Radian init failure

cmts-platform-infr

LOG_STD_ACTION

COBALT-3-COBERR

3-Error

Cobalt [chars].

Cobalt generated an error.

cr10k5

"Copy the error message exactly as it appears and report it to your " "technical support representative."

USB-3-USB_OC

3-Error

USB over-current at source 0x[hec].

USB interface over-current error.

cr10k5

"Copy the error message exactly as it appears and report it to your " "technical support representative."

PCIE-3-PCIE_NODEV

3-Error

PRE5 did not find the correct PCIe device ID is 0x[hec]!

PRE5 did not find correct PCIe devices.

cr10k5

"Copy the error message exactly as it appears and report it to your " "technical support representative."

OBFL-3-BFLASHINITERR

3-Error

Failed to initialize the PRE5 OBFL storage device.

PRE5 OBFL storage device init failed.

cr10k5

LOG_STD_ACTION

OBFL-6-OBFLSTORAGECCESS

6-Information

PRE5 OBFL: [chars] operation on OBFL storage failed OBFL address: 0x%X num bytes: [dec]

PRE5 OBFL flash access error.

cr10k5

LOG_STD_ACTION

OBFL-6-OBFLSENSORACCESS

6-Information

PRE5 OBFL: [chars] sensor access failure for sensor [chars]ID:[dec]

-

-

-

CHASSIS-3-PROCESSERR

3-Error

Couldn't start tempeature enviroment monitoring process

The temperature monitoring process could not be started during initialization.

cr10k5

LOG_STD_ACTION

CHASSIS-4-READALERTRESERR

4-Warning

MAX1668 [dec] read alert response address error

MAX1668 read alert response address failed.

cr10k5

LOG_STD_ACTION

CHASSIS-6-EJECT_BUTTON

6-Information

[chars] eject button is being screwed on/off.

There are two ejcet buttons on PRE5 front panel. When any eject button is being screwed on/off the error message will be printed to screen to remind the user.

cr10k5

LOG_STD_ACTION

CHASSIS-3-OPERATION_FORBIDDEN

3-Error

[chars] and try again.

There are two ejcet buttons on PRE5 front panel. When both eject buttons are pulled out or a CLI plugin-card-preotec enable/disable So the software modules protected by this may fail such as write/erase based on bootflash chip

cr10k5

"Please tighten the screws of the eject button."

CR10KBH-1-INITFAIL

1-Alert

[chars] initialization failure

Backhaul Ethernet hardware initialization failed

ubr10k-sw

LOG_STD_ACTION

CR10KBH-3-MAXADDR

3-Error

[chars] total addresses greater than [chars]

The number of addresses in the address filter is too large

ubr10k-sw

LOG_STD_ACTION

CR10KBH-6-B2B_LINKUP

6-Information

[chars] B2B port [dec] changed state to up

Link state changed to up for B2B interface

ubr10k-sw

LOG_STD_NO_ACTION

CR10KBH-3-B2B_LINKDOWN

3-Error

[chars] B2B port [dec] changed state to down

Link state changed to down for B2B interface

ubr10k-sw

"Check the sfp+ and wire status for B2B interface"

CR10KBH-6-B2B_SFPP_OK

6-Information

[chars] B2B port [dec] SFP+ inserted

TenGigabit Ethernet SFP+ was inserted into the B2B interface

ubr10k-sw

LOG_STD_NO_ACTION

CR10KBH-3-B2B_SFPP_MISSING

3-Error

[chars] B2B port [dec] SFP+ missing

TenGigabit Ethernet SFP+ was removed from the B2B interface

ubr10k-sw

"Insert a TenGigabit ethernet SFP+ into the B2B interface"

CR10KBH-6-SFPP_OK

6-Information

Interface [chars] 10GBASE-[chars] TenGigabit ethernet module SFP+ inserted

TenGigabit Ethernet SFP+ was inserted into the Backhaul interface

ubr10k-sw

LOG_STD_NO_ACTION

CR10KBH-3-SFPP_MISSING

3-Error

Interface [chars] TenGigabit ethernet module SFP+ missing

TenGigabit Ethernet SFP+ was removed from the Backhaul interface

ubr10k-sw

"Insert a TenGigabit ethernet SFP+ into the Backhaul interface"

CR10KBH-3-SFPP_NON_TENGIGE

3-Error

Interface [chars] Inserted module not TenGigabit ethernet module SFP+

Non TenGigabit Ethernet SFP+ was inserted into the Backhaul interface

ubr10k-sw

"Insert a TenGigabit ethernet SFP+ into the Backhaul interface"

CR10KBH-3-SFPP_BAD_HW

3-Error

Interface [chars] TenGigabit Ethernet module SFP+ has bad HW

TenGigabit Ethernet SFP+ could not be read CRC error or tx fault

ubr10k-sw

"Insert a new TenGigabit Ethernet SFP+ into the Backhaul interface"

CR10KBH-3-SFPP_SECURITY_FAIL

3-Error

Interface [chars] TenGigabit Ethernet module SFP+ is not CISCO approved

TenGigabit Ethernet SFP+ has failed cisco-EEPROM security check

ubr10k-sw

"Insert a approved vendor SFP+ into the Backhaul interface"

CR10KBH-3-SFPP_SPURIOUS

3-Error

Interface [chars] TenGigabit Ethernet module SFP+ is a duplicate spurious

TenGigabit Ethernet SFP+ has a vendor & serial number duplicate of another

ubr10k-sw

"Insert a approved vendor SFP+ into the Backhaul interface"

CR10KBH-3-INVALID_DATA_INSTANCE

3-Error

interface type [chars] slot [dec] subunit [dec] vc [dec] : [chars]

Data required to support the interface is not available.

ubr10k-sw

LOG_STD_SH_TECH_ACTION

CR10KBH-3-RADIAN_VLANTCAM_EXCEEDED

3-Error

[chars] vlanid [dec] Radian VLAN TCAM table full

Radian has a maximum of 4K vlan tcam entries

ubr10k-sw

LOG_STD_SH_TECH_ACTION

CR10KBH-6-RADIAN_MACACCT_FULL

6-Information

MAC accounting entries full for Radian in slot [chars]

Radian has a maximum of 256 ingress and 256 egress MAC accounting entries

ubr10k-sw

LOG_STD_SH_TECH_ACTION

CR10KBH-3-WIRING_ERR

3-Error

Wrong wiring detected at [chars] interconnect portportnum: [dec] please

This error message will be printed out when local interconnect port link status mismatches with remote interconnect port link status. We should use cable fiber to connect the corresponding interconnect ports between active and standby. When the error msg is printed out please check: 1 if

ubr10k-sw

LOG_STD_SH_TECH_ACTION

IOS_LICENSE-2-NO_MEM

2-Critical

No memory available for [chars]

The Ios licensing subsystem could not obtain the memory it needed.

ios-licensing

"If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt."

IOS_LICENSE-2-NO_LICENSE

2-Critical

No valid license avaiable to run any feature

The Ios licensing subsystem could not get a valid license to run any feature on the box please purchase a license.

ios-licensing

"Purchase a valid license to run the features you requier on the " "box. You should contact the cisco portal or a TAC engineer to get " "a license. You can do a <CmdBold>show license<noCmdBold> at the " "privileged command line prompt to get the list of availabe feature " "in the box "

IOS_LICENSE-3-IPC_FAILED

3-Error

[chars] failed with an error = [chars]

The ipc calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE-3-UNKNOWN_MSG_TYPE

3-Error

an unknown message type was received dropping it msg_type = [dec]

Ios licensing subsystem received a msg type which it does not recognizes or support

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE-3-RTTYS_FAILED

3-Error

[chars] failed

The rttys calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE-3-FAILED

3-Error

[chars]

The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-3-FAILED

3-Error

[chars]

The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_EVENT

3-Error

[chars]

The ios image licensing subsystem received an event which it does not understand or recognizes

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_VERSION

3-Error

[chars]

The ios image licensing subsystem received an event for an unknown version of a feature

ios-licensing

"please capture the error msg and forward it to the appropriate licensing component"

IOS_LICENSE_IMAGE_APPLICATION-6-NO_LICENSE

6-Information

[chars] [chars].

There is no valid license available on the box and we are running on a default feature

ios-licensing

"please purchase a license to activate required features"

IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL

6-Information

Module name = [chars] Next reboot level = [chars] and License = [chars]

This is an informational message to display the change in the next reboot license level

ios-licensing

"This is an informational message no action is required"

IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL_CONFIG

6-Information

Please issue 'license boot' config command to make extension license [chars] available for use.

This is an informational message to info user that to make extension license available to support image level licensing image level needs to be configured

ios-licensing

"This is an informational message no action is required"

IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_CONFIG

6-Information

EULA must be accepted for license level = [chars]

This is an informational message to inform user that the user needs to reissue the command from an interactive terminal

ios-licensing

"This is an informational message no action is required"

LICENSE-1-ENFORCEMENT

1-Alert

Feature [chars] [chars] running without a License. UDI=[chars]

End User License Agreement was accepted on this device

none

"none"

LICENSE-2-NO_MEM

2-Critical

No memory available for [chars]

The IOS licensing subsystem could not obtain the memory it needed.

ios-licensing

"If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt."

LICENSE-2-VLS_ERROR

2-Critical

'[chars]' failed with an error - rc = [dec] - '[chars]'

The IOS licensing subsystem encountered an error with the VLS api

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service"

LICENSE-3-IMPLICIT_LIC

3-Error

[chars]

The IOS licensing subsystem encountered an error while initializing/handling the implicit licenses

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service"

LICENSE-2-LIC_STORAGE

2-Critical

[chars]

The IOS licensing subsystem does not have a primary storage

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service"

LICENSE-2-LIC_STORAGE_CORRUPT

2-Critical

[chars] UDI=[chars]

The IOS licensing subsystem detected corrupted storage

ios-licensing

"If this error message occurs please reinstall all the licenses." "If you do not have the licenses please contact Cisco with the correct" "UDI to get all the licenses issued for this particular device"

LICENSE-6-RECOVERED

6-Information

The IOS license storage on this device was recovered. UDI=[chars]

The IOS license storage on this device was recovered

ios-licensing

"none"

LICENSE-2-UNRECOVERABLE

2-Critical

The IOS license storage on this device was not recovered. UDI=[chars]

The IOS license storage on this device was not recovered

ios-licensing

"If this error message occurs please reinstall all the licenses."

LICENSE-3-LIC_PROCESS_CREATION_FAILED

3-Error

[chars]

The IOS licensing subsystem was unable to create a process

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-2-IPC_INIT

2-Critical

License IPC subsystem could not be initialized: [chars]

License IPC subsystem could not be initialized. The reason for failure is displayed after :

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-3-IPC_PORT

3-Error

License [chars] IPC port [chars] failed: [chars]

License IPC port could not be created. The reason for failure is displayed after :

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-3-SLAVE_REGISTER

3-Error

License Slave device registration failed : [chars]

License Slave registration failed. The reason for failure is displayed after :

ios-licensing

"If this error message recurs please copy the message and " "and contact the customer service See whether the system resources" "are available"

LICENSE-1-EXPIRING

1-Alert

License for feature [chars] [chars] will expire in [chars]. UDI=[chars]

License for the feature specified will expire in the specified time.

ios-licensing

"If this message recurs customer should buy license for the feature" " from Cisco since feature will not run after license expiry"

LICENSE-1-EXPIRED

1-Alert

License for feature [chars] [chars] has expired [chars]. UDI=[chars]

License for the feature specified has expired

ios-licensing

"If this message recurs customer should buy the license from Cisco " "since feature will not run"

LICENSE-1-REQUEST_FAILED

1-Alert

License request for feature [chars] [chars] failed. UDI=[chars]

Your system is trying to run a feature without a license.

none

"Please buy and install the license for the feature immediately"

LICENSE-4-PRECEDENCE

4-Warning

Setting precedence for feature [chars] failed with error : [dec]

A license is revoked from the system

none

"This is just an informational message to" " log a message when a license has been revoked"

LICENSE-6-COUNT

6-Information

Feature [chars] [chars] license count changed from [dec] to [dec].

The feature's maximum licensable count has changed

none

"This is just an informational message to" "denote count change for particular feature"

LICENSE-6-VIOLATION

6-Information

Feature [chars] [chars] count violation - count = [dec] usage count = [dec].

The feature's count is less than the current usage count

none

"This is just an informational message to" "denote count change for particular feature"

LICENSE-4-UDI_MISMATCH

4-Warning

The source license udi[chars]:[chars] differs from the platform udi[chars]:[chars] please save the running config.

The source license udi mismatches with the platform udi

none

"Please save running-config."

LICENSE-4-LIC_AGENT_OFF

4-Warning

License Agent is turned off. UDI=[chars]

The License Agent on this device is not running

none

"Please check the device configuration " "if you need to enable it."

LICENSE-1-VALIDITY_ENDING

1-Alert

Feature [chars] [chars] will expire on [chars]. UDI=[chars]

-

-

-

LICENSE-1-VALIDITY_EXT_ENDING

1-Alert

Feature [chars] [chars] in grace period. UDI=[chars]

-

-

-

LICENSE-1-VALIDITY_ENDED

1-Alert

Feature [chars] [chars] [chars]. UDI=[chars]

-

-

-

LICENSE-3-IPC_ERROR

3-Error

[chars][chars] [hec] rc:[chars]

Licensing is experiencing errors when communicating to Line Cards using IPC

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_XMIT

3-Error

Client id:[dec] type = [dec] xmit failed error:[dec]

Licensing is experiencing errors when performing ISSU Transformation during a transmit operation

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_RCV

3-Error

Client id:[dec] type = [dec] receive failed error:[dec]

Licensing is experiencing Errors when performing ISSU Transformation during a receive operation

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_ERR

3-Error

[chars] error:[dec]

Licensing is experiencing ISSU Errors

ios-licensing

"show ipc ports"

LICENSE-3-ISSU_MTU

3-Error

Client id:[dec] MTU failed error:[dec]

Licensing is experiencing Errors when performing ISSU GET MTU during a transmit operation

ios-licensing

"show issu nego"

REDUNDANCY-2-IPC

2-Critical

[chars] [chars]

-

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-MEMORY_DIFF

3-Error

WARNING nonsymetrical configuration:\n Active has [dec]K Standby has [dec]K\n

The redundant RPs have different memory configurations.

ehsa

"The configuation is allowed but discouraged."

REDUNDANCY-3-FSM

3-Error

[chars]

-

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-FSM_ERROR

3-Error

[chars] Error Code: [dec]

-

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-SWITCHOVER

3-Error

RP switchover [chars]

A REDUNDANCY switchover has occurred.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-STANDBY_LOST

3-Error

Standby processor fault [chars]

The standby processor is no longer available.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-PEER_MONITOR

3-Error

[chars]

A REDUNDANCY Peer Monitor error occurred. The details about\n\ what was attempted and what went wrong will be printed.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-5-PEER_MONITOR_EVENT

5-Notice

[chars] [chars][chars][dec]\n

A REDUNDANCY Peer Monitor event occurred and reported. The report should\n\ help to find out the reason for a switch-over.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-REDUNDANCY_ALARMS

3-Error

[chars]

A REDUNDANCY Alarm assertions error occurred. The details about\n\ what was attempted and what went wrong will be printed.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-CONFIG_SYNC

3-Error

[chars]

A REDUNDANCY config sync error occurred. The details about\n\ what was attempted and what went wrong will be printed.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-3-GENERAL

3-Error

[chars]

A REDUNDANCY error occurred. The details about\n\ what was attempted and what went wrong will be printed.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

REDUNDANCY-4-RELOADING_STANDBY

4-Warning

Reloading the Standby [chars]

The Active has sent a reload IPC request to the Standby peer. If the reload is not successful then the Standby will be power cycled instead.

ehsa

LOG_STD_ACTION

REDUNDANCY-4-PEER_DID_NOT_RESPOND

4-Warning

Resetting peer [chars] because it did not respond to verification of HA role.

The Standby peer has reloaded itself to correct a configuration mismatch between the Active and the Standby. The Standby has detected that it is missing configuration for a line card. This has most likely happened because the Standby was reloaded prior to the new card being inserted.

ehsa

LOG_STD_NO_ACTION

REDUNDANCY-6-SWITCHOVERTIME

6-Information

Time taken to switchover = [dec] milliseconds

This is how long the Standby peer took to become Active after a failure of the existing Active.

ehsa

LOG_STD_NO_ACTION

REDUNDANCY-3-EHSAISSU

3-Error

[chars] failed with error code [ [chars] ]

An ISSU related REDUNDANCY error occurred. The details about\n\ what was attempted and what went wrong will be printed.

ehsa

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

NICKEL10G-3-N10GERRSEND

3-Error

[chars] - ERR EVENT [chars] port [dec] reporting to PRE

Fatal errors occured on Nickel10g reported to PRE

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GERRSSUSPEND

3-Error

Too many Nickel10g ERR EVENTS [dec] suspending reporting

Too many errors reported on Nickel10g

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GERREVT

3-Error

[chars] - ERR EVENT [chars] port [dec]

Non fatal errors occured on Nickel10g

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GNOTUP

3-Error

N10G is not operationally up

Nickel10g is not operationally up

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GPREMISMATCH

3-Error

PRE-A/B mismatch in N10G - driver:[dec] fpga:[dec]

PRE-A/B mismatch in N10G driver

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GFIBNR

3-Error

FIB is not Running reporting it to PRE

FIB is not in RUNNING state report to PRE for further action

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GERRDD

3-Error

[chars]: [chars] - [dec] [dec]

Nickel10g non-fatal error

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GERRS

3-Error

[chars]

Nickel10g non-fatal generic error

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GERRD

3-Error

[chars]: [chars] - [dec]

Nickel10g non-fatal generic error

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GINVIRB

3-Error

[chars]

Invalid Ironbus mode [dec] defaulting to QUAD

ubr10k-sw

"LOG_STD_ACTION"

NICKEL10G-3-N10GSPIFAIL

3-Error

N10G-Waxbill SPI link is out of sync

-

ubr10k-sw

"LOG_STD_ACTION"

BCM5396-3- MDIO_TIMEOUT

3-Error

MDIO Timeout [chars]

No response was received from the GigE switch MDIO interface

ubr10k-sw

"Investigate possible Raven MDIO interface"

BCM5396-3- READ_TIMEOUT

3-Error

Timeout waiting for read pg [dec] addr [dec] len [dec]

Failed to read a page register via MDIO.

ubr10k-sw

"Investigate possible error with Raven or GigE switch."

BCM5396-3- WRITE_TIMEOUT

3-Error

Timeout waiting for write pg [dec] addr [dec] len [dec]

Failed to read a page register via MDIO.

ubr10k-sw

"Investigate possible error with Raven or GigE switch."

BCM5396-3- MODEL_ID

3-Error

Failed to read model id

Failed to read a register via MDIO.

ubr10k-sw

"Investigate possible error with Raven or GigE switch."

BCM5396-3- BAD_MODEL_ID

3-Error

Unexpected model id: 0x%X

The model ID of the part was not correct

ubr10k-sw

"Investigate possible error with Raven or GigE switch."

FMEA-4-DS_JIB_ERRLOG

4-Warning

DS JIB Santana FPGA Err log [chars] [chars]

DS JIB Santana FPGA FMEA failure log

cmts-infra

"Minor non-fatal recoverable failure event"

SANTANA-3-DS_JIB_ERROR

3-Error

DS JIB Santana FPGA Error detected and corrected

DS JIB Santana FPGA Error corrected

cmts-infra

"Contact TAC to collect debug log from the linecard"

GE_LINK-5-SWITCHOVER_PRI

5-Notice

primary port set active for GE pair [dec]

GE link is restored for primary port

cmts-platform

"if not expected check secondary port in GE pair"

GE_LINK-5-SWITCHOVER_SEC

5-Notice

secondary port set active for GE pair [dec]

GE link is lost for primary port

cmts-platform

"if not expected check secondary port in GE pair"

GE_LINK-4-SWITCHOVER_ERR

4-Warning

switchover to primary port in GE pair is suppressed due to port instability

-

cmts-platform

"check GE link"

GE_LINK-3-SW_ERR

3-Error

[chars] error in GE pair [dec] port [dec]

Internal software error

cmts-platform

"Copy the error message exactly as it appears and report it to your " "technical support"

GE_LINK-5-AUTONEGOTIATION

5-Notice

Waiting for completed A/N in GE pair [dec] primary port

-

cmts-platform

"If persistent check peer GigabitEthernet port"

GE_LINK-3-MDIO_ERR

3-Error

[chars] error for controller [dec] port [dec]

Error in accessing GigE Transceiver

cmts-platform

"Copy the error message exactly as it appears and report it to your " "technical support"

GE_LINK-5-UPDOWN

5-Notice

Link status is [chars] for GE pair [dec] port [dec]

Link Status Change detected for GigE Transceiver

cmts-platform

"If not expected check GIGE link"

GE_LINK-6-PHY_EVENT

6-Information

PHY [chars] event detected for phy [dec] port [dec]

Link Event detected for non-SFP port of GigE Transceiver

cmts-platform

"Copy the error message exactly as it appears and report it to your " "technical support"

LCD_DISPLAY-3-CHAR_ERROR

3-Error

Invalid character

This character is not supported by card LCD

cmts-platform

"Copy the error message exactly as it appears and report it to your " "technical support"

LCD_DISPLAY-4-INPUT_ERROR

4-Warning

Invalid input DS [dec] US [dec] channels

Wrong number of D/S or U/S channels

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LCD_DISPLAY-4-STATUS_ERROR

4-Warning

Invalid status

Invalid status bit

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-4-LTC2978_ALERT

4-Warning

LTC2978power fault monitor open drain alert for device #[dec]

Interrupt from LTC2978

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-5-POWER_FAILURE

5-Notice

Power failure happened in previous power cycle. Check OBFL logs for details.

LTC2978 recorded power failure in previous power cycle.

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-4-VOUT_FAULT

4-Warning

Output Voltage Fault is reported by LTC2978. [chars]

LTC2978 reported Output Voltage Fault

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-4-VIN_FAULT

4-Warning

Input Voltage Fault is reported by LTC2978. [chars]

LTC2978 reported Input Voltage Fault

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-5-TEMPERATURE_FAULT

5-Notice

Temperature Fault is reported by LTC2978. [chars]

LTC2978 reported Temperature Fault. [chars]

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support along with the temperature values reported by MAX1668" " using test cable envm temp dump [1|2|3] command on LC console"

LTC2978-4-CML_FAULT

4-Warning

Communication Fault is reported by LTC2978. [chars]

LTC2978 reported Communication Fault

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-4-LOG_CLEAR_MAX_RETRIES

4-Warning

Tried [dec] times to read transfer status after clearing log for 2978-[dec] and the read was unsuccessful

Log clear didn't work for LTC2978

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

LTC2978-4-LOG_RESTORE_MAX_RETRIES

4-Warning

Tried [dec] times to read log data after log restore for 2978-[dec] and the read was unsuccessful

Fatal Recoverable Raven interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-3-FATAL_ERP_ERROR

3-Error

erp_mst_cfg 0x[hec] erp_mst_err_phase 0x[hec] erp_mst_err_addr 0x[hec]

Fatal Raven ERP interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-3-FATAL_LCL_BUS_ERROR

3-Error

cap_reg 0x[hec] cap_data 0x[hec] cap_access 0x[hec] [chars] transaction

Fatal Unrecoverable Local Bus error

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-3-FATAL_REC_LCL_BUS_ERROR

3-Error

cap_reg 0x[hec] cap_data 0x[hec] cap_access 0x[hec] [chars] transaction

Fatal Recoverable Local Bus error

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-3-FATAL_REC_RLDRAM_ECC_ERROR

3-Error

err_rec_addr 0x[hec] err_rec_data3 0x[hec] err_rec_data2 0x[hec]\n err_rec_data1 0x[hec] err_rec_data0 0x[hec] err_rec_ecc 0x[hec]

High Priority Raven Single Error Upset interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-4-TSS_PARITY_EVENT

4-Warning

[chars] event

TSS Parity interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-4-TSS_MISMATCH_EVENT

4-Warning

[chars] event

TSS Mismatch interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-4-TSS_LOAD_EVENT

4-Warning

[chars] event

RLDRAM interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

RAVEN-5-PLL_NONFATAL_UNLOCK_EVENT

5-Notice

[chars] unlock

Expected PLL unlock

cmts-platform

"If this event appears after/close to TCC reload it is expected." "Otherwise copy the error message exactly as it appears and report" " it to your technical support"

RAVEN-3-PLL_UNEXPECTED_UNLOCK_EVENT

3-Error

[chars] unlock

Low Priority Raven interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

POWR1220-4-INIT_NO_RESPONSE

4-Warning

POWR1220 is not responding. The device is [chars]

POWR1220 device is not responding

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

POWR1220-4-INIT_SEQUENCE_FAILURE

4-Warning

POWR1220 sequencing failure happened. The device is [chars] and register values are reg 0x03 0x%02x reg 0x04 0x%02x reg 0x05 0x%02x reg 0x07 0x%02x reg 0x08 0x%02x

POWR1220 device registers do now show correct values

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

SFP-3-SW_ERR

3-Error

SFP Driver error: [chars] sfp [dec] errcode [dec]

Internal error in SFP driver

-

"Copy the error message exactly as it appears and report it to your" " technical support"

SFP-5-SFP_OK

5-Notice

[chars] SFP inserted in port [dec]

SFP inserted

-

"If not expected copy the error message exactly as it" " appears and report it to your technical support"

SFP-3-SFP_UNINITIALIZED

3-Error

[chars] SFP inserted in port [dec] error status [dec]

SFP inserted initialization failed

cmts-platform

"If not expected copy the error message exactly as it " "appears and report it to your technical support"

SFP-5-SFP_MISSING

5-Notice

[chars] SFP missing from port [dec]

SFP removed

cmts-platform

"If not expected copy the error message exactly as it " "appears and report it to your technical support"

SFP-3-SW_I2C_ERR

3-Error

SFP Driver i2c error: [chars] sfp [dec] addr 0x[hec] errcode [dec]

i2c Access error to SFP device

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

I2C-5-LTC4306

5-Notice

sanity check failed: device 0x[hec] channel [dec] action [chars] retry [dec] read back 0x[hec]

-

cmts-platform

-

I2C-3-ACCESS_ERR

3-Error

I2C access error [chars] for device [dec]

I2C device initialization error

cmts-platform

"Copy the error message exactly as it appears and report it to your " "technical support"

I2C-3-CONFIG_ERR

3-Error

I2C config failure [chars] for device [dec] value 0x[hec]

I2C device configuration error

cmts-platform

"Copy the error message exactly as it appears and report it to your " "technical support"

CORABI-3-FATAL_N10G_ERP_ERROR

3-Error

ERP errors: [chars] ERP error data: 0x%02x ERP error phase: 0x%01x ERP error addr: 0x%08x

Fatal Corabi N10G ERP interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

CORABI-3-FATAL_N10G_FAULT

3-Error

N10G fault reported

Fatal Corabi N10G Fault interrupt

cmts-platform

"Copy the error message exactly as it appears and report it to your" " technical support"

C4K_REDUNDANCY-6-INIT

6-Information

Initializing as [chars] supervisor

Informational message regarding the state of the supervisor

-

""

C4K_REDUNDANCY-6-MODE

6-Information

[chars] supervisor initializing for [chars] mode

Informational message regarding the redundancy mode of the supervisor

-

""

C4K_REDUNDANCY-6- ACTIVESUPNOTFOUND

6-Information

Active supervisor not found.

Informational message on standby supervisor when it fails to communicate with active supervisor

-

""

C4K_REDUNDANCY-6- ATTEMPTINGTOBECOMEACTIVE

6-Information

Attempting to become active supervisor.

Informational message on standby supervisor when it fails to communicate with active supervisor and attempts to takeover as active supervisor

-

""

C4K_REDUNDANCY-6- SWITCHOVER

6-Information

Switchover activity detected changing role from STANDBY to ACTIVE

Informational message on standby supervisor when it detects switchover activity

-

""

C4K_REDUNDANCY-4- CONFIGSYNCFAIL

4-Warning

Persistent-config Sync to Standby supervisor failed.

Active supervisor failed to receive PLATFORM_SYNC_DONE message from Standby. Potential problem with Standby.

-

""

C4K_REDUNDANCY-5- CONFIGSYNC

5-Notice

The [chars] has been successfully synchronized to the standby supervisor

The configuration has been successfully synchronized to the standby supervisor

-

"This is an informational message. No action is required."

C4K_REDUNDANCY-5- CONFIGSYNC_RATELIMIT

5-Notice

The [chars] has been successfully synchronized to the standby supervisor

The configuration has been successfully synchronized to the standby supervisor This is a rate limited message. These messages are logged at 1 min interval when lots of messages are generated continuously

-

"This is an informational message. No action is required."

C4K_REDUNDANCY-2- POSTFAIL

2-Critical

POST failure on [chars] supervisor detected

Active supervisor failed POST. Standby supervisor will reset current active and attempt to become active.

-

"Please run offline diagnostics on the failed supervisor to isolate the failure"

C4K_REDUNDANCY-2- NON_SYMMETRICAL_REDUNDANT_SYSTEM

2-Critical

[chars]

For proper operation of redundancy the system must be configured with symmetrical hardware. Here we have detected mismatch between the Active and Standby hardware. In this condition redundancy operations are not guaranteed.

-

"Configure the hardware so that the Active and Standby supervisors are identical in all respects."

C4K_REDUNDANCY-2- IOS_VERSION_CHECK_FAIL

2-Critical

[chars]

For proper operation of redundancy the system must be configured with symmetrical hardware and software. Here we have detected an IOS version mismatch between the Active and Standby. In this condition redundancy operations are not guaranteed.

-

"Configure the system so that the Active and Standby supervisors are running the same version of IOS."

C4K_IOSINTF-5-NOTXVLAN

5-Notice

Router Port [chars] has no internal vlan assigned to transmit packet

The L3 Interface specified does not have an internal vlan assigned.

-

-

C4K_IOSINTF-5-TXPKTDROPONETHERCHANNEL

5-Notice

Dropping transmit packet out of interface [chars]

A packet to be transmitted out of a Port-Channel is being dropped during transitions in the Port-Channel membership

-

"This occurs when a packet is being transmitted out of the aggregate " "port by higher layer protocols but the software cannot find specific " "state information. This can temporarily happen when physical ports " "transition into or out of the channel. If the problem persists please " "contact your Cisco Technical Support representative"

C4K_IOSINTF-5-TXL3PKTONPHYPORT

5-Notice

Transmitting L3 packet on a physical port [chars] that is part of [chars] [dec] packets. Make sure the physical port in the L3 port

The L3 protocols operate at the logical port level and not on physical port level. This message indicates an situation that causes L3 protocol packets to be sent on a physical port that is part of a bundle. This can happen if there is a misconfiguration. Maybe there is an ip address assigned to a physical port that is part of a layer 3 port channel

-

LOG_STD_ACTION

C4K_IOSINTF-5-STALEPHYPORT

5-Notice

Dropping packets to be transmitted out on port [chars] Linecard in Slot [dec] may have been removed

During hot-swapping operations sometimes a prevously queued packet may be transmitted after a delay by which time the linecard does not exist anymore. This indicates such packets are being dropped

-

"This occurs when there are queued packets that are transmitted by which " "time the linecard in that slot has been removed already. If the problem " "persists even without any hotswapping operations please contact your " "Cisco Technical Support representative "

C4K_IOSINTF-4-INTVLANALLOCFAIL

4-Warning

Failed to allocate internal VLAN for interface [chars]. The interface will remain down.

When a routed port or port channel interface is enabled it must allocate an internal VLAN in order to operate. If there are no internal VLANs available when an interface is enabled the interface remains down and this message is logged.

-

"An internal VLAN can be freed up by disabling some other routed port " "or port channel interface or by deleting a user configured VLAN in " "the 1006 to 4094 range. Once a VLAN is made available the interface " "will come up if it is disabled and re-enabled."

C4K_IOSINTF-4-REFLEXIVEACLNOTSUPPORTED

4-Warning

Reflexive Acls are not supported. Ignoring the [chars] entry.

Reflexive Acls are not supported. Aces with Evaluate and Reflect keywords are ignored.

-

"Do not configure Aces with Evaluate or Reflect keyword. "

C4K_IOSSYS-7-INVALIDVALUE

7-Debug

[chars] Type [dec] not handled returning a default of 0

This message is for debugging purposes. When you see this message report it to your technical support representative.

cat4000

LOG_STD_ACTION

LRE_CPE-3-UNKNOWNMODEL

3-Error

\nCPE has unrecognizable model number [chars] on interface [chars]

The model number string in the CPE does not match a known CPE model number.

fw-hawaii

"Use the \"show controllers lre cpe mfg\" command " "to examine the Model Number of the CPE. " "Verify that the Model Number is a Cisco-supported " "one. Use the interface configuration command " "\"shutdown\" followed by a \"no shutdown\" to " "force the switch to re-read the CPE Model Number. " "If the error message persists record the output " "of the previously used show command and report the " "problem to your technical support representative."

LRE_CPE-3-WRONGPATCH

3-Error

\nCPE on interface [chars] has wrong patch version [hec]. \nPatch version [hec] or higher is needed for this CPE.

Each CPE requires a currently-supported patch version for it to function. This CPE has a patch version that predates the earliest supported version.This condition might occur because the switch was upgraded with the latest Cisco IOS Software image but the CPE firmware has not been upgraded.

fw-hawaii

"Upgrade the patch on the CPE to the latest " "supported version by using the command " "\"hw-module slot <slot> upgrade lre remote\""

LRE_CPE-3-INVALIDPATCH

3-Error

\nCPE on interface [chars] has invalid LRE firmware.

The LRE firmware header does not have a valid signature or the header information on the specified firmware is inconsistent with the contents of the firmware

fw-hawaii

"Upgrade the firmware on the CPE to the latest " "supported one by using the command " "\"hw-module slot <slot> upgrade lre remote\"."

LRE_CPE-3-INVALIDPHY

3-Error

\nCPE on interface [chars] has an unsupported Ethernet PHY.

The Ethernet PHY device on the CPE attached to the interface specified in the error message is not supported. This error occurs when the switch cannot recognize the PHY identifier of the PHY devices

fw-hawaii

"Verify that the CPE is a Cisco-supported one. " "Use the command \"show controllers lre cpe " "mfg\" to verify that the CPE Model Number " "string is correctly set. If the IOS version and " "CPE model number look correct issue the interface " "configuration command \"shutdown\" followed by " "\"no shutdown\" to force the switch to read the " "PHY identifer again. As a last resort power cycle " "the CPE. If the error persists contact your " "technical support representative."

LRE_CPE-3-INVALIDMODE

3-Error

\nCPE on interface [chars] is in invalid mode [chars].

-

fw-hawaii

"Use the command \"show controllers lre cpe mfg \" " "to verify that the CPE Model Number string is " "correct. Use the command \"hw-module slot <slot> " "lre upgrade remote \" to ensure that the CPE has " "the latest supported firmware. If the CPE's Model " "Number and firmware are correct use the interface " "configuration command \"shutdown\" followed " "by \"no shutdown\" to force the switch to re-read " "CPE information. If the problem persists contact " "your technical support representative."

LRE_CPE-3-WRONGBOOTVER

3-Error

\nCPE on interface [chars] reported unsupported version of bootloader firmware [chars].\nMinimum bootloader firmware version needed [chars]

Each CPE requires a currently-supported bootloader firmware version for it to function correctly. This CPE has a bootloader firmware version that predates the earliest supported version.

fw-hawaii

"Upgrade the bootloader firmware on the CPE to " "a recent version that supports the current " "requirements by using the command \"hw-module " "slot <slot> lre upgrade remote\". If the " "CPE firmware upgrade does not solve the problem " "force the switch to re-read the bootloader " "firmware version by issuing the interface " "configuration command \"shutdown\" followed " "by the command \"no shutdown\". As a last " "resort power cycle the CPE. If the problem " "persists contact your technical support " "representative."

LRE_CPE-3-NOVERCKSUM

3-Error

\nCould not fetch CPE firmware version and checksum on interface [chars].

The system could not obtain the CPE firmware version and checksum. If the CPE has the latest firmware and the CPE Model Number is correct the most likely cause for this error is that the LRE link between the switch and the CPE is of poor quality.

fw-hawaii

"Use the command \"show controllers lre cpe mfg \" " "to verify that the CPE Model Number string is " "correctly set for this CPE. Use the command " "\"hw-module slot <slot> lre upgrade remote\" to " "ensure that the CPE has the latest firmware. " "Use the interface configuration command \"shutdown\" " "followed by \"no shutdown\" to force the switch " "to re-fetch the CPE firmware version and checksum. " "As a last resort power cycle the CPE. If the " "problem persists contact your technical support " "representative."

LRE_CPE-3-WRONGAPPVER

3-Error

\nCPE on interface [chars] reported unsupported version of application firmware [chars].\nMinimum application firmware version needed [chars]

Each CPE requires a currently-supported application firmware version for it to function correctly. This CPE has a application firmware version that predates the earliest supported version.

fw-hawaii

"Application firmware is not currently used " "on the CPE. This error message is for future use."

LRE_CPE-5-SSNCHANGED

5-Notice

\nCPE unit on interface [chars] changed.

The CPE system serial number changed. This condition usually means that the CPE unit on this interface was replaced.

fw-hawaii

"No action is required."

LRE_LINK-3-UPDOWN

3-Error

Interface [chars] changed state to [chars]

The interface hardware either has become active came up

-

"If the state change was unexpected confirm the configuration " "settings for the interface."

LRE_LINK-3-PROFILE_FAILURE

3-Error

Interface [chars] profile [chars] failure

The interface specified in the error message did not achieve link with attached profile.

-

"If the link failure was unexpected confirm the profile settings " "for the interface."

LRE_LINK-4-HEALTH_MON

4-Warning

Interface [chars] had crossed certain monitored thresholds

The link status monitor for the interface specified in the error messages has detected conditions that have crossed the configured thresholds.

-

"Enter the <CmdBold>show controllers lre link monitor<NoCmdBold> command to obtain more information on this error. If the change in operating conditions was unexpected confirm the configuration settings for the interface."

LRE_UPGRADE-3-INIT_SYSTEM

3-Error

Upgrade module failed to initialize

The LRE Upgrade module failed to initialize

-

LOG_STD_ACTION

LRE_UPGRADE-4-INIT_RESOURCE

4-Warning

[chars]

The LRE Upgrade module cannot locate a required resource

-

"Report this message to your service representative"

LRE_UPGRADE-3-LOCAL_FAILURE

3-Error

Upgrade of local controller [chars] failed

LRE upgrade is unable to download firmware to a local controller

-

LOG_STD_ACTION

LRE_UPGRADE-2-LOCAL_LOAD_FAILURE

2-Critical

The system failed to load the firmware for local PHY controller:[dec]

An internal system error has occurred while loading the firmware for a local PHY controller.

-

"Power cycle the switch. If this message persists " "copy the message exactly as it occurs on the " "console or in the system log contact your " "Cisco technical support representative and " "provide the representative with the gathered " "information."

LRE_UPGRADE-4-TERMINATE

4-Warning

Upgrade on [chars] terminated

The CPE was disconnected or changed in the middle of an upgrade.

-

"Verify that the CPE currently connected to the link requires an upgrade."

LRE_LOG-7-LRE_LOGGING

7-Debug

LRE Log:Interface [chars]: State: [chars] Event: [chars] Data: [chars].

The system has changed its state. The error message text provides more information on the nature of the change.

-

LOG_STD_NO_ACTION

PQUICC3-1-NOMEMORY

1-Alert

msgtxt_nomemory

The MPC8500/PowerQUICC CPU was unable to access the memory it needs to\n\ carry out its functions. Here are some possible causes.\n\\n\ The network is large requiring a lot of memory for routing tables and\n\ so on.\n\\n\ The router configuration has many features enabled each of which\n\ require a certain amount of memory.\n\\n\ A software error memory leak exists.

-

"Reduce system activity to ease the memory demand or upgrade to a\n\ larger memory configuration."

PQUICC3-3-OWNERR

3-Error

msgtxt_ownerror

An internal software error occurred.

-

"Call your technical support representative to obtain a software\n\ upgrade."

PQUICC3-1-INITFAIL

1-Alert

PQUICC3[dec]/[dec] SCC[dec] init failed

The software failed to initialize/restart a 1T serial card.

-

"Clear the serial interface.\n\ If the message recurs call your technical support representative for\n\ assistance."

PQUICC3-1-CTSLOST

1-Alert

PQUICC3[dec]/[dec] Clear to Send Lost

-

-

"Check the serial interface cable and/or communication equipment such\n\ as the channel service unit/data service unit CSU/DSU."

PQUICC3-1-UNDERFLO

1-Alert

PQUICC3[dec]/[dec] Transmit underflow

While transmitting a frame the serial controller chip's local buffer\n\ received insufficient data because data could not be transferred to the\n\ chip fast enough to keep pace with its output rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required."

PQUICC3-1-LINEFLAP

1-Alert

PQUICC3[dec]/[dec] Excessive modem control changes

-

-

"Check the serial interface cable. The error can occur if the cable is\n\ disconnected or has come loose and is picking up noise. If the cable\n\ appears to be connected correctly check the equipment connected to the\n\ cable."

PQUICC3-1-BADHDXFSM

1-Alert

PQUICC3[dec]/[dec] Unexpected HDX state [dec] event [dec]

A bad event was detected in the state machine for half duplex\n\ transmission/reception.

-

"Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC3-1-TOOSMALL

1-Alert

PQUICC3[dec]/[dec] packet was less than 2 bytes\n\msgdef_explanation A small packet

-

-

-

PQUICC3-1-TOOBIG

1-Alert

PQUICC3[dec]/[dec] packet too big packet size was [dec] bytes

A packet greater than the assigned MTU of this serial interface\n\ was queued up for transmission.

-

"The system should recover. No action is required.\n\ \n\ If the message recurs it may indicate an error\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC3-1-UNKNOWN_WIC

1-Alert

PQUICC3[dec] WIC card has an unknown ID of 0x[hec]

The software does not recognize the type of WIC card plugged\n\ into the port module.

-

"Check the part number on the WIC card to verify that it is supported\n\ in the IOS release operational on the router or contact\n\ your technical support representative."

PQUICC3-1-WRONG_SLOT

1-Alert

PQUICC3[dec] BRI card in wrong slot1

The BRI card is not supported in WIC slot 0.

-

"Power down move the BRI card to the other WIC slot on the\n\ port module and reboot."

PQUICC3-3-UNKNOWN_SCCS

3-Error

PQUICC3 Incorrect SCC number

An internal software error occurred.

-

"Call your technical support representative to obtain a software\n\ upgrade."

PQUICC3-1-UNSUPPORTED_CONFIG

1-Alert

Slot [dec] has an unsupported combination of ISDN WAN interface cards

It is not possible to support this type of BRI card in\n\ slot 1 along with another BRI card in slot 0.

-

"Remove one of the BRI cards from either slot."

PQUICC3-1-UNEXPECTED_INTERRUPT

1-Alert

PQUICC3[dec] Unexpected modem-signal interrupt

The software did not expect to see a modem control signal change\n\ on this interface.

-

"Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC3-1-QMC_GLOBAL_ERROR

1-Alert

PQUICC3[dec]/[dec] Global error [hec] in QMC

One or more of the channels served by the QMC instance encountered\n\ transmitter underflow or receiver overflow or the QMC interrupt\n\ table overflowed. Normally such a problem is temporary depending on \n\ transient peak loads within the system.

-

"The system should recover. No action is required."

PQUICC3-3-UNKNOWN_SCC_TX_VECTOR

3-Error

PQUICC3 Unknown TX vector on port [dec]

An internal software error occurred.

-

"Copy the error message exactly as it\n\ appears and report it to your technical support representative."

PQUICC3-3-SPURIOUS_INTERRUPT

3-Error

Interface card in slot [dec] generated a spurious interrupt

Interface card on the router which is not supported by this image\n\ generated a spurious interrupt that can not be handled.

-

"No action is required. To avoid seeing this message in the future\n\ remove the unsupported card or use an image that supports it."

PQUICC3-3-DDR_ERR

3-Error

DDR [dec] [chars] error from memory

A soft-parity error from the memory has been detected. Normal system operation should continue

-

"If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative."

PQ3_TSEC-5-LOSTCARR

5-Notice

PQ3/FE[dec] Lost carrier. Transceiver problem?

The cable is not connected to the port.

-

"Connect the cable to the port."

PQ3_TSEC-5-LATECOLL

5-Notice

PQ3/FE[dec] Late collision

Late collisions occurred on the Ethernet/Fast Ethernet interface.

-

"If the interface is Fast Ethernet verify that both\n\ peers are in the same duplex mode. For regular\n\ Ethernet the system should recover. No action is\n\ required."

PQ3_TSEC-3-UNDERFLO

3-Error

PQ3/FE[dec] Transmit underflow

While transmitting a frame the controller chip's local buffer\n\ received insufficient data because data could not be transferred to the\n\ chip fast enough to keep pace with its output rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required."

PQ3_TSEC-5-EXCESSCOLL

5-Notice

PQ3/FE[dec] Excessive collision

Ethernet/Fast Ethernet is seeing multiple collisions. This\n\ may occur under heavy loads.

-

"The system should recover. No action is\n\ required."

PQ3_TSEC-3-OVERFLO

3-Error

PQ3/FE[dec] Receive overflow

While receiving a frame the controller chip's local buffer\n\ transmitted insufficient data because data could not be transferred to\n\ DRAM fast enough to keep pace with its input rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required."

PQ3_TSEC-4-BABBLE

4-Warning

PQ3/FE[dec] Babble error CSR[dec]=0x%04x

The transmitter has been on the\n\ channel longer than the time taken to transmit the largest\n\ frame.

-

"The system should recover. No action is required."

PQ3_TSEC-1-MEMERR

1-Alert

PQ3/FE[dec] Memory error CSR[dec]=0x%04x

The interface could not access system resources for a\n\ long time. This problem may occur under very heavy loads.

-

"The system should recover. No action is required. If the message recurs call\n\ your technical support representative for assistance."

PQ3_TSEC-1-INITFAIL

1-Alert

PQ3/FE[dec] Init failed CSR[dec]=0x%04x

The software failed to initialize/restart an Ethernet/Fast Ethernet interface.

-

"Clear the interface. If the message recurs call your\n\ technical support representative for assistance."

PQ3_TSEC-1-INITFAILP

1-Alert

PQ3/FE[dec] Init failed at [chars]

The FEC could not allocate a I/O buffer pool.

-

"Clear the interface. If the message recurs call your\n\ technical support representative for assistance."

PQ3_TSEC-1-SHOWFAIL

1-Alert

PQ3/FE[dec] Memory error at [chars]

The FEC could not allocate memory to display controller.

-

"Clear the interface. If the message recurs call your\n\ technical support representative for assistance."

PQ3_TSEC-3-OWNERR

3-Error

PQ3/FE[dec] Buffer ownership error pak=0x[hec]

The software detected an error in descriptor ownership.

-

"Try a later version of the software. If the message " "recurs call your technical support representative " "for assistance."

PQ3_TSEC-5-COLL

5-Notice

PQ3/FE[dec] Excessive collisions TDR=[dec] TRC=[dec].

-

-

-

PQ3_TSEC-2-NOISL

2-Critical

Interface [chars] does not support ISL

The interface cannot be configured as an ISL trunk.

-

"Check the configuration."

PQ3_FE-5-LOSTCARR

5-Notice

PQ3/FE[dec]/[dec] Lost carrier. Transceiver problem?

The cable and/or transceiver is not connected.

-

"Connect the cable and/or transceiver."

PQ3_FE-5-LATECOLL

5-Notice

PQ3/FE[dec]/[dec] Late collision

Late collisions occurred on the Fast Ethernet interface.

-

"If the interface is Fast Ethernet verify that both\n\ peers are in the same duplex mode. No action is\n\ required."

PQ3_FE-5-EXECOLL

5-Notice

PQ3/FE[dec]/[dec] Excessive collision

Excessive collisions occurred on the Fast Ethernet interface.

-

"No action is required."

PQ3_FE-3-UNDERFLO

3-Error

PQ3/FE[dec]/[dec] Transmit underflow

While transmitting a frame the controller chip's local buffer\n\ received insufficient data because data could not be transferred to the\n\ chip fast enough to keep pace with its output rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required."

PQ3_FE-3-OVERFLO

3-Error

PQ3/FE[dec]/[dec] Receive overflow

While receiving a frame the controller chip's local buffer\n\ transmitted insufficient data because data could not be transferred to\n\ DRAM fast enough to keep pace with its input rate. Normally such a\n\ problem is temporary depending on transient peak loads within the\n\ system.

-

"The system should recover. No action is required."

PQ3_FE-4-BABBLE

4-Warning

PQ3/FE[dec]/[dec] Babble error CSR[dec]=0x%04x

The transmitter has been on the\n\ channel longer than the time taken to transmit the largest\n\ frame.

-

"The system should recover. No action is required."

PQ3_FE-1-INITFAILP

1-Alert

PQ3/FE[dec]/[dec] Init failed at [chars]

The FE could not allocate a I/O buffer pool.

-

"Clear the interface. If the message recurs call your\n\ technical support representative for assistance."

PQ3_FE-1-SHOWFAIL

1-Alert

PQ3/FE[dec]/[dec] Memory error at [chars]

The FEC could not allocate memory to display controller.

-

"Clear the interface. If the message recurs call your\n\ technical support representative for assistance."

PQ3_FE-2-NOISL

2-Critical

Interface [chars] does not support ISL

The interface cannot be configured as an ISL trunk.

-

"Check the configuration."

PQ3_FE-1-MACADDRFAIL

1-Alert

PQ3/FE[dec]/[dec] Unable to set the Mac-address for the interface

The FEC could not set the mac address of the interface.

-

"Clear the interface. If the message recurs call your\n\ technical support representative for assistance."

SYSTEM_CONTROLLER-3-INFO1

3-Error

[chars]=0x[hec]

Information regarding the internal state of system controller

msfc2

LOG_STD_ACTION

SYSTEM_CONTROLLER-3-INFO2

3-Error

[chars]=0x%08x0x%08x

Information regarding the internal state of system controller

msfc2

LOG_STD_ACTION

SYSTEM_CONTROLLER-3-DUMP

3-Error

System controller Global Registers Dump

Information regarding the internal state of system controller

msfc2

LOG_STD_ACTION

SYSTEM_CONTROLLER-3-ERROR

3-Error

Error condition detected: [chars]

Information regarding an error condition detected by the system controller:normal operation continues

msfc2

LOG_STD_RECUR_ACTION

SYSTEM_CONTROLLER-3-RESET

3-Error

Resetting system controller due to [chars]

The system controller is being reset due to internal errors

msfc2

LOG_STD_ACTION

SYSTEM_CONTROLLER-3-MISTRAL_RESET

3-Error

System Controller is reset:Normal Operation continues

The system controller is being reset : Message rate limited

msfc2

"show ibc"

SYSTEM_CONTROLLER-3-FATAL

3-Error

An unrecoverable error has been detected. The system is being reset.

The system controller has detected an unrecoverable error condition.

msfc2

LOG_STD_ACTION

SYSTEM_CONTROLLER-3-THRESHOLD

3-Error

Mistral interrupt count is [dec] Supervisor will reset on hitting threshold [dec].

The system controller has detected an unrecoverable error condition. But since this is a standalone supervisior we merely reset the controller instead of reloading the supervisor. Once the count of the mistral error interrupts hits the threshold value the supervisor will be reloaded. The default threshold value is 5

msfc2

LOG_STD_ACTION

SYSTEM_CONTROLLER-3-COR_MEM_ERR

3-Error

Correctable DRAM memory error. Count [dec] log %08x

A correctable error in system DRAM occurred:normal operation continues.

msfc2

"No action needed if additional DRAM errors do not occur."

SYSTEM_CONTROLLER-3-MORE_COR_ERR

3-Error

[chars] [dec] correctable DRAM memory errors in previous hour

Multiple correctable errors have occurred in system DRAM

-

"Reboot system at next convenient time. If error persists after reboot" " call your Cisco technical support representative to arrange repairs."

INBAND-3-INV_TX_PACKET

3-Error

[chars]: packet neither on IBL nor on OBL

The packet to be transmitted is neither on the IBL nor on the OBL:normal operation continues

msfc2

LOG_STD_RECUR_ACTION

INBAND-3-NOBUF

3-Error

Dropping the packet.

The system controller receive buffer pool has been exhausted. No further input packets can be handled until some buffers are returned to the pool:normal operation continues

msfc2

LOG_STD_RECUR_ACTION

INBAND-6-BAD_IDB

6-Information

Bad idb for vector [chars]: [chars] vlan [dec] total [dec]

Bad idb returned from get_l3_swidb

msfc2

LOG_STD_RECUR_ACTION

INBAND-3-BAD_PAK

3-Error

Possibly un-encapsulated packet passed to Mistral: int [chars] type [dec] stat 0x[hec] flags 0x[hec] size [dec] offset [dec] requeue_token [dec] r1 [dec] r2 [dec] total detected [dec]

Badly encapsulated packet from process level

msfc2

LOG_STD_ACTION

INBAND-3-INVALID_PAK

3-Error

Sent from [chars] with invalid [chars] of [dec] bytes with source vlan:[dec] and packetsize:[dec]

Badly formed packet in inband fastpath or process level

msfc2

LOG_STD_ACTION

INBAND_or_EOBC-3-INVALID_SEND

3-Error

Invalid send operation packet on [chars]

Internal error caused illegal call to device driver:normal operation continues

msfc2

LOG_STD_RECUR_ACTION

NILE_ASIC-2-TCAM_PARITY_ARRAY_ERR

2-Critical

TCAM4 Parity Array Error at Asic: [dec] TCAM Index: 0x[hec] Application: [chars] Region [chars]

The system detected a parity error in the TCAM4 and the entry was invalidated. This will result in unexpected traffic forwarding behavior.

hardware

"Reload switch."

NILE_ASIC-2-TCAM_PARITY_IO_ERR

2-Critical

TCAM4 Parity IO Error at Asic: [dec]

The system detected a parity error in the TCAM4 IO. This will result in unexpected traffic forwarding behavior.

hardware

"Reload switch."

NILE_ASIC-2-TCAM_PHASE_ERR

2-Critical

TCAM4 Phase Error Detected at Asic: [dec].

The system detected a phase error in the TCAM4. This is considered a fatal error.

hardware

"Reload switch."

NILE_ASIC-2-BIT_INTR_TX_ERROR

2-Critical

PCI device [dec] receiving TX Interrrupt Errors

The system detected errors while responding to interrupts on the PCI device. This can result in erroneous behaviour. If the error persists reload the hardware.

me360x-me380x-system

"Reload switch."

NILE_ASIC-2-BIT_INTR_INITIATOR_ABORT

2-Critical

PCI device [dec] failing to initiate

The system detected initiation errors. If the error persists reload the hardware. If the box is stuck in this state replace the hardware.

hardware

"Reload switch."

NILE_ASIC-2-BIT_INTR_TX_TRANSFER_INT

2-Critical

PCI device [dec] receiving TX transfer interrupt errors

The system detected errors while transferring in the tx direction on the PCI device. This can result in erroneous behaviour. If the error persits reload the hardware

me360x-me380x-system

"Reload switch."

NILE_ASIC-2-BIT_INTR_PCI_INITIATOR_FATAL_ERROR

2-Critical

PCI device [dec] received fatal errors on initiation

The system detected initiation errors. If the error persists reload the hardware. If the box is stuck in this state replace the hardware.

hardware

"Reload switch."

NILE_ASIC-2-BIT_INTR_PCI_INITIATOR_PARITY_ERROR

2-Critical

PCI device [dec] received parity errors

The system is receiving corrupted packets on PCI device. This could be due to improper NILE ASIC access. If the box is stuck in this state reload the hardware.

me360x-me380x-system

"Reload switch."

OUTPUT_CLK_SEL-6-T4DPLL_CLK_STATE_CHANGE

6-Information

Output clock state changed to [chars].

Output clock state changed.

ran-opt

LOG_STD_NO_ACTION

OUTPUT_CLK_SEL-3-GEN_FRM_RLOS

3-Error

BITS Receive Loss of Sync

This msg reports interrupt changes

-

LOG_STD_NO_ACTION

OUTPUT_CLK_SEL-3-GEN_FRM_FRCL

3-Error

BITS Framer Receive Carrier Loss

This msg reports interrupt changes

-

LOG_STD_NO_ACTION

OUTPUT_CLK_SEL-3-GEN_FRM_RUA1

3-Error

BITS Receive Unframed All One's T1 Blue Alarm E1 AIS

This msg reports interrupt changes

-

LOG_STD_NO_ACTION

ESF_MPLS-3-ESF_FIB_ADD_FAILED

3-Error

Attempt to add ESF tagged route [inet]/[dec] Table %lu failed

An internal software error occurred.

firmware

LOG_STD_ACTION

ESF_MPLS-3-EREVENT

3-Error

[chars]

An internal software error occurred.

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-ERROR

3-Error

[chars]

Platform nile cef module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-NULL_HANDLE

3-Error

[chars]

Platform nile cef null handle error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-FIB

3-Error

[chars]

Platform nile cef prefix related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-ADJ

3-Error

[chars]

Platform nile cef adj related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-LB

3-Error

[chars]

Platform nile cef load balance related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-LB_MAP

3-Error

[chars]

Platform nile cef load balance map related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-TABLE

3-Error

[chars]

Platform nile cef table related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-ADJ_BACKWALK

3-Error

[chars]

Platform nile cef Adj Backwalk related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-LB_BACKWALK

3-Error

[chars]

Platform nile cef LB Backwalk related error occured

firmware

LOG_STD_ACTION

PLATFORM_NCEF-3-INTERFACE

3-Error

[chars]

Platform nile cef interface related error occured

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-HSRP

3-Error

[chars]

Platform unicast routing hsrp module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-INTERFACE

3-Error

[chars]

Platform unicast routing interface related error occured

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-ADJ

3-Error

[chars]

Platform unicast routing adjacency module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-ARP

3-Error

[chars]

Platform unicast routing arp module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-CEF

3-Error

[chars]

Platform unicast routing cef module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-4-PREFIX

4-Warning

Prefix [inet]/[dec] could not be programmed into TCAM

A more specific prefix could not be programmed into TCAM and is covered by a less specific prefix. This could be a temporary condition. If it persists configuring a SDM template which allows higher number of routes may fix this problem. The <cmdBold>show platform ip unicast failed route<nocmdBold> command lists failed prefixes at a given time.

me3600-me3800-l3

LOG_STD_NO_ACTION

PLATFORM_UCAST-3-DYNAMIC

3-Error

[chars]

Platform's dynamic address tracking mechanism encountered an error.

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-RPC

3-Error

[chars]

Platform unicast routing rpc module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-NULL_HANDLE

3-Error

[chars]

Platform unicast routing module received a NULL software object handle

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-LB

3-Error

[chars]

Platform unicast routing loadbalance module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-LB_BACKWALK

3-Error

[chars]

Platform unicast routing backwalk loadbalance module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_UCAST-3-ERROR

3-Error

[chars]

An internal platform unicast routing error occurred

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-ERROR

3-Error

[chars]

Platform ipv6 unicast routing module encountered an error

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-FIB

3-Error

[chars]

Platform ipv6 unicast routing prefix related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-ADJ

3-Error

[chars]

Platform ipv6 unicast routing adj related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-LB

3-Error

[chars]

Platform ipv6 unicast routing load balance related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-INTERFACE

3-Error

[chars]

Platform ipv6 unicast routing interface related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-ND

3-Error

[chars]

Platform ipv6 unicast routing neighbor discovery related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-PROXY

3-Error

[chars]

Platform ipv6 unicast routing ND-Proxy related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-TABLE

3-Error

[chars]

Platform ipv6 unicast routing table related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-ADJ_BACKWALK

3-Error

[chars]

Platform ipv6 unicast routing Adj Backwalk related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-LB_BACKWALK

3-Error

[chars]

Platform ipv6 unicast routing LB Backwalk related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPv6_UCAST-3-RPC

3-Error

[chars]

Platform ipv6 unicast routing RPC related error occured

firmware

LOG_STD_ACTION

PLATFORM_IPV6HOST-2-CANNOT_INIT

2-Critical

Insufficient resources to initialize platform-specific IPv6 host functionality

The platform-specific part of the IPv6 host support failed to initialize at boot time.

-

"IPv6 cannot be used on this system"

SP_MONITOR-6-NOT_HEARD

6-Information

SP_MONITOR messages have not been heard for [dec] seconds [[dec]/[dec]]

SP_MONITOR messages have not been heard for a significant amount of time. It\n\ is likely that a timeout will occur soon which will reset the SP processor.

-

LOG_STD_NO_ACTION

SP_MONITOR-3-PEER_FAILED

3-Error

SP_MONITOR peer process has failed to receive heartbeats reset SP proc [[dec]/[dec]]

SP_MONITOR messages have failed on the peer process and\n\ the SP proc would be reset.

-

LOG_STD_NO_ACTION

SP_MONITOR-3-PEER_EXCEPTION

3-Error

SP_MONITOR peer has failed due to exception reset SP proc [[dec]/[dec]]

SP_MONITOR messages have failed on the peer processor and\n\ the SP proc would be reset.

-

LOG_STD_NO_ACTION

SP_MONITOR-3-TIMED_OUT

3-Error

SP_MONITOR messages have failed resetting [chars] [[dec]/[dec]]

SP_MONITOR messages have failed and the SP proc would be reset.

-

LOG_STD_NO_ACTION

PLATFORM_ENV-3-ENV_INIT_FAIL

3-Error

Environmental Driver Initialization Error

The Environmental Driver failed to initialize. There is no way to determine the switch system voltage rail thermal and fan status behavior

firmware

"If the fault persists please replace the " "component and/or update the environmental driver."

PLATFORM_ENV-3-GLUE_INIT_FAIL

3-Error

Hardware Tracking Driver Initialization Error

The Hardware Tracking Driver failed to initialize. There is no way to determine the switch FRU power supplies SFP FPGA SPI JTAG and Alarms behavior

firmware

"If the fault persists please replace the " "component and/or update the driver."

PLATFORM_ENV-3-GLUE_INTR_NOT_FUNCTIONING

3-Error

Hardware Tracking Driver: State Change Detection not functioning

The Hardware Tracking Driver no longer detects state changes. There is no way to determine the switch FRU power supplies SFP FPGA SPI JTAG and Alarms state change

firmware

"Ensure that the ambient temperature is not too high" "in the area. If the fault persists please replace the component and/or " "update the driver."

PLATFORM_ENV-3-VOLTAGE_NOT_FUNCTIONING

3-Error

Voltage Rail Sensors are not functioning

The voltage rail sensors are not functioning There is no way to determine the switch voltage rail behavior

hardware

"Ensure that the ambient temperature is not too high" "in the area. If the fault persists please replace the component and/or " "update the driver."

PLATFORM_ENV-3-THERMAL_NOT_FUNCTIONING

3-Error

Temperature Sensor is not functioning

The temperature sensor is not functioning There is no way to determine the switch temperature behavior

hardware

"Ensure that the ambient temperature is not too high" "in the area. If the fault persists please replace the component and/or " "update the driver."

PLATFORM_ENV-3-MCU_I2C_READ_ERROR

3-Error

I2C read failed in MCU and attached devices e.g. Temperature Sensor can't be read.

MCU I2C rea dfailed. The temperature sensor etc. read failed in MCU. There is no way to determine the switch temperature behavior

hardware

"Ensure that the ambient temperature is not too high" "in the area. If the fault persists please replace the component."

PLATFORM_ENV-2-THERMAL_WARNING

2-Critical

Temperature has reached warning threshold

The temperature sensor value inside the switch has reached the warning threshold. The switch can function normally untill the temperature reaches the critical threshold

hardware

"The external temperature is high." " Reduce the temperature in the room"

PLATFORM_ENV-1-THERMAL_CRITICAL

1-Alert

Temperature has reached critical threshold

The temperature sensor value inside the switch has reached the critical threshold. Switch cannot function normally

hardware

"The external temperature is very high." " Reduce the temperature in the room immediately"

PLATFORM_ENV-5-THERMAL_NORMAL

5-Notice

Temperature is within the acceptable limit

The temperature sensor value inside the switch is within the normal limit

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-6-FRU_FAN_OIR

6-Information

FRU FAN [chars]

FAN inserted or removed

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-FRU_FAN_OK

1-Alert

FRU[chars] fan ok

FRU fan working ok

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-FAN

1-Alert

Faulty fan[chars] detected

Faulty fan detected

firmware

"If the fault persists replace the fan."

PLATFORM_ENV-1-PLATFORM_FAN_CRITICAL

1-Alert

[chars]

Faulty fansFRU fan or PS fan detected

hardware

"Replace the faulty fans and then turn on the system"

PLATFORM_ENV-1-FAN_NOT_PRESENT

1-Alert

Fan is not present

Fan is not present

firmware

"If it is a removable fan insert it back into the " "switch. If fault persists after insertion replace the fan"

PLATFORM_ENV-1-TEMP

1-Alert

Abnormal temperature detected

Abnormal temperature detected

firmware

"Ensure that ambient temperature is not too high in" " the area. If fault persists replace the component"

PLATFORM_ENV-1-PWR

1-Alert

Internal power supply not supplying power

Internal power supply is not supplying power because either the cable is removed or the power supply is faulty

firmware

"Check the power supply cables and the power " "source. " LOG_STD_RECUR_ACTION

PLATFORM_ENV-1-PWR_RPS

1-Alert

Redundant power supply faulty or in standby mode

Redundant power supply is either faulty or it is in standby mode

firmware

"Move the redundant power supply out of standby" " mode and check the cables. Refer to the RPS " "User's Guide for the steps. " LOG_STD_RECUR_ACTION

PLATFORM_ENV-1-FRU_PS_SIGNAL_OK

1-Alert

[chars] signal on power supply [dec] is restored

The specified signal of power supply has been restored

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-FRU_PS_OK

1-Alert

power supply [dec] is good

No faults detected on power supply

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-FRU_PS_SIGNAL_FAULTY

1-Alert

[chars] signal on power supply [dec] is faulty

The specified signal of power supply is faulty

hardware

LOG_STD_ACTION

PLATFORM_ENV-1-FRU_PS_FAN_FAILED

1-Alert

Faulty PS[chars] fan detected

Power supply fan failure detected

hardware

"Replace the faulty fan"

PLATFORM_ENV-1-FRU_PS_FAN_OK

1-Alert

PS[chars] fan ok

Power supply fan working ok

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-6-FRU_PS_OIR

6-Information

FRU Power Supply [chars]

Power Supply inserted or removed

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-FRU_PS_ACCESS

1-Alert

[chars]

Switch failed to access power supply due to communication problem

firmware

"This problem could be transient. If fault " "persists replace the power supply"

PLATFORM_ENV-1-DUAL_PWR

1-Alert

Faulty internal power supply [chars] detected

Faulty internal power supply detected in two power supplies supported platforms

firmware

LOG_STD_ACTION

PLATFORM_ENV-6-RPS

6-Information

Redundant Power SupplyRPS [chars]

Redundant Power Supply RPS changed state

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-3-RPS_FAULTY_BACKUP

3-Error

[chars]

RPS error condition detected

firmware

"This problem could be transient. If fault " "persists remove and reconnect the switch"

PLATFORM_ENV-1-RPS_STANDBY

1-Alert

[chars]

Faulty RPS detected

firmware

LOG_STD_ACTION

PLATFORM_ENV-1-RPS_ACCESS

1-Alert

[chars]

RPS communication error detected

firmware

LOG_STD_ACTION

PLATFORM_ENV-6-RPS_INFO

6-Information

Redundant Power Supply [chars]

Related info about RPS

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-2-RPS_THERMAL_WARNING

2-Critical

RPS temperature has reached warning threshold

The temperature sensor value inside RPS has reached the warning threshold. RPS can function normally until the temperature reaches the critical threshold

hardware

"The external temperature is high." " Reduce the temperature in the room"

PLATFORM_ENV-1-RPS_THERMAL_CRITICAL

1-Alert

RPS temperature has reached critical threshold

The temperature sensor value inside RPS has reached the critical threshold. RPS cannot function normally

hardware

"The external temperature is very high." " Reduce the temperature in the room immediately"

PLATFORM_ENV-5-RPS_THERMAL_NORMAL

5-Notice

RPS temperature is within the acceptable limit

The temperature sensor value inside RPS is within the normal limit

hardware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-RPS_PS_THERMAL_CRITICAL

1-Alert

RPS power supply [chars] temperature has reached critical threshold

The power supply inside RPS has reached the critical threshold. RPS cannot function normally

hardware

"The external temperature is very high." " Reduce the temperature in the room immediately"

PLATFORM_ENV-1-RPS_PS_FAN_FAILED

1-Alert

RPS power supply [chars] fan failure detected

RPS power supply fan failure has been detected

hardware

"Disconnect any switches connected to the RPS and " "replace the power supply immediately"

PLATFORM_ENV-1-RPS_PS_SIGNAL_FAULTY

1-Alert

[chars] signal on RPS power supply [chars] is faulty

The specified power supply of RPS has faulty signal

hardware

LOG_STD_ACTION

PLATFORM_ENV-3-RPS_BACKOFF_FAILED

3-Error

[chars]

RPS is continuing to backup switch even though switch issued a command to backoff

firmware

LOG_STD_NO_ACTION

PLATFORM_ENV-1-RPS_PS_MISMATCH

1-Alert

[chars]

Power supplies inserted in RPS are incompatible

firmware

"Remove either one of the power supplies or " "insert compatible power supplies"

PLATFORM_ENV-1-RPS_FAN_FAILED

1-Alert

[chars]

RPS fan failure detected

hardware

"Disconnect any switches connected to the RPS and " "replace the fan immediately"

PLATFORM_ENV-1-RPS_OVER_CURRENT

1-Alert

[chars]

RPS overcurrent condition detected

hardware

"Unplug the switches that are being backed off"

PLATFORM_ENV-3-RPS_POST_FAILED

3-Error

[chars]

RPS POST failure detected

firmware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-6-RPS_PS_INSERTED

6-Information

[chars]

Power supply inserted in RPS

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-6-RPS_PS_REMOVED

6-Information

[chars]

Power supply removed from RPS

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-3-RPS_CHANGE_TO_STANDBY

3-Error

[chars]

RPS has changed state to standby. It will no longer backup the switch

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-1-RPS_SYS_POWER_GOOD

1-Alert

[chars]

RPS system power changed state to good

hardware

"LOG_STD_NO_ACTION"

PLATFORM_ENV-1-RPS_SYS_POWER_BAD

1-Alert

[chars]

RPS system power changed state to bad. It may not provide backup

hardware

"Check the power supplies in RPS. If fault " "persists replace the power supply"

PLATFORM_ENV-1-PS_NONPOE

1-Alert

Internal Power supply not adequate for inline power

Internal Power supply not adequate for inline power

firmware

"Procure a power supply that can provide adequate" "inline power"

PLATFORM_ENV-3-SMB_RESET_EXCEEDED

3-Error

[chars] 0x%02x

Faulty device detected

firmware

LOG_STD_ACTION

PLATFORM_ENV-3-SMB_HW_FAULT

3-Error

[chars] 0x%2x

Faulty Bus State detected

firmware

LOG_STD_ACTION

PLATFORM_ENV-1-EXTERNAL_ALARM_CONTACT_ASSERT

1-Alert

Alarm asserted: [chars]

Error condition detected on external alarm contact

hardware

LOG_STD_ACTION

PLATFORM_ENV-1-EXTERNAL_ALARM_CONTACT_CLEAR

1-Alert

Alarm cleared: [chars]

Error condition cleared on external alarm contact

hardware

LOG_STD_ACTION

PLATFORM_ENV-3-ILP_PORT_POST_ERR

3-Error

[chars] can't be brought up because it failed POST in Inline Power test.

An error reported by the Power over Ethernet PoE controller

hardware

LOG_STD_SH_TECH_ACTION

PLATFORM_ENV -3-LOOPBACK_PORT_POST_ERR

3-Error

[chars] can't be brought up because it failed POST in Loopback test.

A loopback error detected during POST.

hardware

LOG_STD_SH_TECH_ACTION

ENVIRONMENT-4-SECONDARY_UNDERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the configured min temperature \ threshold but less or equal to the max inside temperature

-

-

ENVIRONMENT-4-SECONDARY_OVERTEMP

4-Warning

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the configured threshold \ but less or equal to the max inside temperature

-

-

ENVIRONMENT-3-OVERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature exceeds the max temperature threshold

-

-

ENVIRONMENT-3-UNDERTEMP

3-Error

[chars] [chars] [chars] [chars]

The chassis inside temperature is below the min temperature threshold

-

-

ENVIRONMENT-3-RPS_FAILED

3-Error

[chars] [chars] [chars] [chars]

Only one power supply was detected for system in dual power mode or \ power supply is failing

-

-

ENVIRONMENT-4-SECONDARY_OVERVOLT

4-Warning

[chars] [chars] [chars] [dec]

The voltage rail returns to normal range from above max voltage threshold

-

-

ENVIRONMENT-4-SECONDARY_UNDERVOLT

4-Warning

[chars] [chars] [chars] [dec]

The voltage rail returns to normal range from below low voltage threshold

-

-

ENVIRONMENT-3-OVERVOLT

3-Error

[chars] [chars] [chars] [dec]

The voltage rail is above the max voltage threshold

-

-

ENVIRONMENT-3-UNDERVOLT

3-Error

[chars] [chars] [chars] [dec]

The voltage rail is below the min voltage threshold

-

-

HARDWARE-3-ASICNUM_ERROR

3-Error

Port-ASIC number [dec] is invalid

Each Port-ASIC is identified by an ID. The port ASIC number used is invalid and this is an internal error

firmware

LOG_STD_ACTION

HARDWARE-3-PORTNUM_ERROR

3-Error

port number [dec] is invalid

Each interface in a given Port-ASIC is identified using an index value. The port-number used is not valid out of range

firmware

LOG_STD_ACTION

ACLMGR-2-NOVMR

2-Critical

Cannot generate hardware representation of access list [chars]

There were insufficient resources available for generating a hardware representation of the access list. Either lack of available logical operation units or lack of memory can cause this problem. Logical operation units are needed when a match on TCP flags is specified or when any test other than eq that is: ne gt lt or range is

firmware

"Modify the ACL configuration to use fewer resources."

ACLMGR-2-NOMAP

2-Critical

Cannot create ACL Manager data structures for VLAN Map [chars]

The ACL Manager could not allocate the data structures needed to describe a VLAN Map in a form that can be loaded into hardware. Probably caused by lack of free memory.

firmware

LOG_STD_REDUCE_ACTION

ACLMGR-2-NOVLB

2-Critical

Cannot create memory block for VLAN [dec]

The ACL Manager was unable to save per-VLAN information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly.

firmware

"Use a less complicated configuration that " "requires less memory."

ACLMGR-3-NOLABEL

3-Error

Cannot allocate [chars] label for vlan-id [dec]

The ACL Manager was unable to allocate a label for the features on this interface. This means that the hardware cannot be programmed to implement the features and packets for this interface will be filtered in software. There is a limit of 256 labels per direction.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible."

ACLMGR-4-UNLOADING

4-Warning

Unloading [chars] [chars] label [dec] [chars] [chars]feature

The ACL Manager was unable to fit the complete configuration into the hardware so some features will have to be applied in software. This prevents some or all of the packets in a VLAN/port from being forwarded in hardware and requires them to be forwarded by the CPU. Multicast packets may be dropped entirely instead of being forwarded.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible."

ACLMGR-4-RELOADED

4-Warning

Reloading [chars] [chars] label [dec] [chars] [chars]feature

The ACL Manager was able to fit more of the configured features on this label into the hardware. One or more features had previously been unloaded because of lack of space.

firmware

LOG_STD_NO_ACTION

ACLMGR-3-MERGEFAIL

3-Error

[chars] ACL merge error [dec] [chars] on [chars] label [dec]

The ACL Manager was unable to complete the merge of the configured features into a form suitable for loading into the hardware. Packets potentially affected by this feature will be sent to the CPU for processing instead. The most likely cause is specifying an ACL that is too large or too complex for the system to handle.

firmware

"Try specifying a smaller and less complicated " "configuration."

ACLMGR-3-INSERTFAIL

3-Error

Insert of access-map [chars] #[dec] into [chars] label [dec] failed

The system ran out of CPU DRAM when trying to merge sections of an access map.

firmware

LOG_STD_REDUCE_ACTION

ACLMGR-3-AUGMENTFAIL

3-Error

Augmenting of access-map [chars] on [chars] label [dec] failed

The system ran out of CPU DRAM when attempting to merge internally required elements with the configured access maps.

firmware

LOG_STD_REDUCE_ACTION

ACLMGR-3-INTTABLE

3-Error

Not in truth table: VLMAP [dec] RACL [dec] Rtprot [dec] Mcb [dec] Feat [dec]

An unrecoverable software error occurred while trying to merge the configured input features.

firmware

"show running-config"

ACLMGR-3-OUTTTABLE

3-Error

Not in truth table: RACL [dec] VLMAP [dec]

An unrecoverable software error occurred while trying to merge the configured output features.

firmware

"show running-config"

ACLMGR-3-PACLTTABLE

3-Error

Not in truth table: IPSrcGrd [dec] PACL [dec] Rtprot [dec]

An unrecoverable software error occurred while trying to merge the configured port acl features.

firmware

"show running-config"

ACLMGR-3-QOSTTABLE

3-Error

Not in truth table: ACL [dec] in map action [dec]

A software error occurred while trying to merge a QoS Policy Map

firmware

"show running-config"

ACLMGR-3-MAXRECURSION

3-Error

Too many [dec] levels of recursion while merging ACLs code [dec].

The configuration is too complicated for the platform specific ACL merge code to support. Most likely cause is including too many separate access lists in a single VLAN map or policy map.

firmware

"Reduce the number IP or MAC access lists" " considered separately in any one VLAN or policy"

ACLMGR-4-ACLTCAMFULL

4-Warning

[chars]ACL TCAM Full. Software Forwarding packets on [chars] label [dec] on [chars] [chars]

The ACL configuration is too large to fit in the platform -specific ACL TCAM table.

firmware

"Simplify the ACLs applied to interfaces or reduce" " their number."

ACLMGR-4-ACLTCAMFULL

4-Warning

ACL TCAM Full. [chars] [chars] [chars] [chars]

The ACL configuration is too large to fit in the platform -specific ACL TCAM table.

firmware

"Simplify the ACLs applied to interfaces or reduce" " their number."

ACLMGR-3-UNKNOWNACTION

3-Error

Unknown VMR access group action 0x[hec]

An internal software error has occurred.

firmware

LOG_STD_ACTION

ACLMGR-3-UNKNOWNL4OPERATION

3-Error

Unknown L4 operation 0x[hec]

ACL Manager module received invalid value for L4 operation. The problem can be due to memory corruption or bad system memory.

firmware

NACL_L4OP_ERROR

ACLMGR-3-INVALIDL4PORTINDEX

3-Error

Invalid L4 port array index while processing [chars]

ACL Manager module received invalid value for L4 port array index. The problem can be due to memory corruption or bad system memory.

firmware

NACL_L4OP_ERROR

ACLMGR-3-IECPORTLABELERROR

3-Error

ACL labels are out-of-sync on interface [chars] label [dec] is not available on asic [dec]

An internal software error has occurred.

firmware

LOG_STD_ACTION

ACLMGR-3-FEATUREMISMATCH

3-Error

[chars] can not be supported with the image running on switch-[dec]

A feature has been configured on the stack but can not be supported on one or more switches in the stack. This feature will continue to work on the rest of the switches that support it but will not be applied to the switches that can not support it. All other features continue to work as expected on the stack.

firmware

"Upgrade the software running on switches that " "can not support this feature. Upgrade to a " "software version that supports this feature."

ACLMGR-3-INVALIDPARAM

3-Error

Invalid [chars] [dec] encountered

ACL Manager has encountered an invalid parameter value.

firmware

"show running-config"

ACLMGR-4-UNLOADINGFSPAN

4-Warning

Unloading [chars] session [dec] [chars] feature

The ACL Manager was unable to fit the complete Flow based SPAN configuration into the hardware so this feature has been temporarily disabled for the given session.

firmware

"Allocate more space to the ACL section of the " "TCAM by choosing an SDM template with more ACL " "TCAM space and reboot the switch. You may also " "use a simpler ACL configuration and/or use the " "same ACLs on multiple interfaces if possible."

ACLMGR-4-RELOADEDFSPAN

4-Warning

Reloading [chars] session [dec] [chars] feature

The ACL Manager was able to fit more of the configured Flow based SPAN features on this session into the hardware. One or more features had previously been unloaded because of lack of space.

firmware

LOG_STD_NO_ACTION

PLATFORM_PM-3-IFCOUNTERROR

3-Error

Creation of [chars] exceeds the exceeds the maximum limit for the number of interfaces of type [chars] [dec]

The system supports a limited number of interfaces for each interface type. The user created more than the supported number of interfaces of this type

firmware

LOG_STD_ACTION

PLATFORM_PM-3-HOSTACCESSFAIL

3-Error

Unable to configure hardware to [chars] host access on [chars]. Port may not behave as expected.

The system was unable to configure the hardware to set the requested host access policy. There may be insufficient TCAM resources available.

firmware

"Stop all traffic issue clear mac-address-table " "dynamic and remove and re-issue the command that failed."

PLATFORM-1-CRASHED

1-Alert

[chars]

The system is attempting to display the crash message from the previous crash.

firmware

LOG_STD_ACTION

PLATFORM-1-CRASH_PCIE

1-Alert

ERROR PCIE-[dec]: Fatal error. ERR_DR=0x[hec] ERR_CAPT=0x[hec] ERR_CAPT_R0=0x[hec] ERR_CAPT_R1=0x[hec] ERR_CAPT_R2=0x[hec] ERR_CAPT_R3=0x[hec]

The system is crashing due to a PCIE hardware error.

firmware

LOG_STD_ACTION

PLATFORM-3-NO_HARDWARE_RESOURCES

3-Error

Not enough hardware resources. Shutting down [chars]

Too many vlans and routed ports

firmware

"Reduce the total number of vlans and routed ports" "to be less than 1023 . If this configuration" "and connectivity needs to be maintained across" "reboots save the configuration to nvram"

PLATFORM-6-MODULE_INSERTED

6-Information

[chars] module inserted in slot [dec] [chars]

The system supports two types of modules a 10GE X2 and a 2 1GE SFP Module in slot 1/2. The module is inserted

firmware

LOG_STD_NO_ACTION

PLATFORM-6-MODULE_REMOVED

6-Information

[chars] module removed in slot [dec] [chars]

The system supports two types of modules a 10GE X2 and a 2 1GE SFP Module in slot 1/2. The module is removed

firmware

LOG_STD_NO_ACTION

QOSMGR-3-ASIC_PROGRAMMING_FAIL

3-Error

Fails to program the ASIC for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_PROGRAMMING_FAIL

3-Error

Fails to program TCAM for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_EXHAUSTION

3-Error

Internal Error in resource allocation

The system is running out of TCAM entries to support the number of traffic classes in the policy-map. The maximum number of TCAM entries is platform dependent.

firmware

"Reduce the number of classes in attached policy-maps"

QOSMGR-3-LABEL_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of QoS label to support the number of traffic classes in all attached policy-maps.

firmware

"Reduce the number of distinctive class-maps matches " "or 'set' actions in attached policy-maps"

QOSMGR-3-TABLEMAP_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of table-map resources

firmware

"Reduce the number of distinctive class-map " "matches in attached policy-maps"

QOSMGR-3-TABLEMAP_MODIFY

3-Error

Table-Map modification Error

Table-Map is being used

firmware

"Create a new Table-Map template" "with the different name"

QOSMGR-4-STATISTICS_FAIL

4-Warning

Internal Error in reading statistics

Can not access to HW to read statistics successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-POLICER_PROGRAMMING_FAIL

3-Error

Fails to program HW policer

Can not access to HW successfully.

firmware

""

QOSMGR-4-POLICER_EXCEEDING_HW

4-Warning

Policer configuration has exceeded hardware limitation for policymap [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-3-INGRESS_QOS_HANDLE_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-handle to support specified policy-map.

firmware

""

QOSMGR-3-INGRESS_QOS_PROFILED_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-profiled to support the specified policy-map.

firmware

""

QOSMGR-3-SCHEDULER_PROGRAMMING_FAIL

3-Error

Fails to program HW scheduler

Can not access to HW successfully.

firmware

""

QOSMGR-4-QUEUE_EXCEEDING_HW

4-Warning

Queue configuration has exceeded hardware limitation for policymap [chars]

The system is running out of output queues to support the specified policy-map.

firmware

"Reduce the number of the traffic classes in attached output policy-maps."

QOSMGR-4-INVALID_POLICYMAP_DUE_NON_QOS_EVENT

4-Warning

The policy-map [chars] is detached due to the event [chars].

The attached policy-map becomes invalid due to the change of the port speed.

firmware

"Change the shaping/bandwidth of the output policy-map and re-attach to the interface ."

QOSMGR-3-OUT_OF_TCAM_RESOURCES

3-Error

Out of tcam resources to execute command

Lack of tcam resources due to higher tcam resource requirements

firmware

"Change config to reduce tcam entry usage"

QOSMGR-3-PROFILES_EXHAUSTED

3-Error

Out of rm profiles to execute command

No free RM profile to accommodate the request

firmware

"Change config to reduce or reuse RM profiles"

QOSMGR-3-QUEUE_FLUSH_FAILED

3-Error

Queue-Flush not successful

Scheduler unable to flush the queue

firmware

"Remove any shape configuration for the queue"

QOSMGR-3-MAX_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum queue-limit commands per class

Trying to exceed the maximum queue-limit commands allowed per class

firmware

"Try reducing queue-limit commands under the class"

QOSMGR-3-MAX_QUALIFIED_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum qualified queue-limit commands per class

Trying to exceed the maximum qualified queue-limit commands allowed per class

firmware

"Try reducing qualified queue-limit commands " "under the class"

QOSMGR-3-UNSUPPORTED_QLIMIT_UNITS

3-Error

Qlimit unit other than usec & byte is not supported

Trying to configure a qlimit unit other than bytes or usec

firmware

"Configure qlimit in terms of bytes or usec"

QOSMGR-3-QLIMIT_VALUE_OUT_OF_RANGE

3-Error

Qlimit value is out of range

Trying to configure a qlimit value outside the supported range

firmware

"Configure qlimit value within supported range"

QOSMGR-3-QLIMIT_LEVEL_ERROR

3-Error

Qlimit command not supported in non-leaf classes

Trying to configure qlimit in a non leaf class

firmware

"Configure qlimit only in leaf classes"

QOSMGR-3-WRED_LAVEL_ERROR

3-Error

random-detect command not supported in non-leaf classes

Trying to configure random-detect in a non leaf class

firmware

"Configure random-detect only in leaf classes"

QOSMGR-3-QLIMIT_PERCENT_ERROR

3-Error

qlimit-limit percent is oversubscribed

qlimit-limit percent is oversubscribed

firmware

"Config queue-limit percent appropriately"

QOSMGR-3-MANUAL_SHAPE_EXCEEDS_SPEED

3-Error

Invalid policy-map detected during interface speed change

Shape value in policy exceeds port speed

firmware

"Configure lesser shape value which will not " "exceed interface speed"

QOSMGR-3-BANDWIDTH_OVERSUBSCRIBED

3-Error

Bandwidth oversubscribed in the interface

Sum of committed bandwidth at a particular level exceeds the sum total of interface's max bandwidth

firmware

"Reduce the committed bandwidth to be less that " "interface's max bandwidth"

QOSMGR-3-SHAPE_UNDERFLOW

3-Error

New shape/speed value is less than the total bandwidth configured in the interface

Shape/speed configured is less than the total bandwidth configured in the interface

firmware

"Increase the shape/speed value or reduce " "the bandwidth configured in the child classes"

QOSMGR-3-BANDWIDTH_LEVEL_ERROR

3-Error

Bandwidth command not acceptable at interface level

Hardware does not support bandwidth at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-PRIORITY_LEVEL_ERROR

3-Error

Priority command not acceptable at interface level

Hardware does not support priority at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-BANDWIDTH_SHAPE_ERROR

3-Error

Bandwidth configured is greater than shapePIR of the class

Bandwidth should not be greater than shape value

firmware

"Reduce the bandwidth value to less than" " class's shapePIR value"

QOSMGR-3-BANDWIDTH_PARENT_SHAPE_ERROR

3-Error

Sum of bandwidths is greater than parent class's shapePIR

Total bandwidth of the classes at the same level exceeds the parent class's shapePIR value

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_PARENT_ERROR

3-Error

Sum of bandwidths is greater than parent class's bandwidth

Total bandwidth of the classes at the same level exceeds the parent class's bandwidth

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_CHILD_ERROR

3-Error

Bandwidth in one of the children class is greater than input bandwidth

Children class's bandwidth should not be greater

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-PROFILE_EXHAUST

3-Error

No free scheduler profiles available in hardware

With the new configuration there is no free profile available in the HW this could be because of dissimilar profiles configured at the same hierarchy level

firmware

"Change the config value to closest existing config"

QOSMGR-3-EFP_SHAPE_RESTRICTION

3-Error

EFP policies cannot have shape command at physical level and more than one logical level classes

Since the HW does not support four level hierarchy EFP policies sit in pseudo level between Physical and Logical level

firmware

"Either remove vlan hierarchy in the EFP policy or" " do not configure shape command at physical level"

QOSMGR-3-SHAPE_PARENT_ERROR

3-Error

Shape value is greater than parent class's shape or interface's speed

Parent class's shape value cannot be smaller than current

firmware

"Configure shape value lesser than parent class's" " shape or interface's speed"

QOSMGR-3-SHAPE_CHILD_ERROR

3-Error

One of children class's shape config is higher

Children class's shape should not be higher than current

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_CHILD_BANDWIDTH_ERROR

3-Error

Bandwidth in one of the children class is greater than input shape value

Children class's bandwidth should not be higher than input

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_BANDWIDTH_PERCENT_ERROR

3-Error

Shape - Bandwidth-percent values inconsistent in the hierarchy calculated bandwidth will exceed shape

Because of this new shape command Bandwidth percent configured in one of children class will get more value than its manually configured shape. Please note that bandwidth percent is calculated from parent's shapePIR

firmware

"Either configure higher shape value or " " reduce violating bandwidth-percent value"

QOSMGR-3-LOGICAL_RESOURCE_EXHAUSTED

3-Error

Logical level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused logical level classes"

QOSMGR-3-QUEUE_EXHAUSTED

3-Error

Class level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused class level classes"

QOSMGR-3-EQOS_CXT_EXCEEDED

3-Error

Maximum Egress QosContexts consumed in the Bridge-Domain

Number of Egress QoS vlan matches exceeds the maximum allowed in the Bridge-Domain

firmware

"Reduce the number of Egress QoS vlan" " matches in the Bridge-Domain and try again"

QOSMGR-3-MAX_WRED_THRESHOLDS_EXCEEDED

3-Error

Exceeding the maximum number of wred thresholds per class

Trying to exceed the maximum wred thresholds allowed per class

firmware

"Try to use not more than two threhshold combination" " under the class"

QOSMGR-3-UNSUPPORTED_WRED_UNITS

3-Error

WRED threshold unit other than usec & byte is not supported

Trying to configure a WRED threshold unit other than bytes or usec

firmware

"Configure WRED threshold in terms of bytes or usec"

QOSMGR-3-WRED_LEVEL_ERROR

3-Error

random-deteact command not supported in non-leaf classes

Trying to configure random-detect in a non leaf class

firmware

"Configure random-detect only in leaf classes"

QOSMGR-3-WRED_VALUE_OUT_OF_RANGE

3-Error

random-detect value is out of range

Trying to configure a random-detect value outside the supported range

firmware

"Configure qlimit value within supported range"

MEM_DDR-1-AC_ERR

1-Alert

DDR automatic calibration error detected at 0x%08x

This error is set if the memory controller detects an error during\n\ its training sequence. This kind of an error is not one that the DDR\n\ Ctrl shouldn't report under its normal operating conditions and \n\ when it does it most probably indicates a malfunctioning DDR module\n\ that needs replacement.

-

LOG_STD_ACTION

MEM_ECC-2-MBE

2-Critical

Multiple bit error detected at 0x%08x

A multi-bit uncorrectable error was detected on a CPU read from DRAM.

-

LOG_STD_ACTION

MEM_ECC-2-MBE_RMW

2-Critical

Multiple bit error detected\nat 0x%08x on a read-modify-write cycle

A multi-bit uncorrectable error was detected during a read-modify- \n\ write cycle on a CPU read from DRAM for a non 8-byte access.

-

LOG_STD_ACTION

MEM_ECC-3-SYNDROME_MBE

3-Error

8-bit Syndrome for the detected Multi-bit error: 0x[hec]

The 8-bit syndrome for detected Multi-bit error. This value does not\n\ indicate the exact positions of the bits in error but can be used to \n\ approximate their positions.

-

LOG_STD_ACTION

MEM_ECC-2-PARITY

2-Critical

Parity error on CPU write to address: 0x%08x

Bad parity on data was detected by the ECC Ctrl during a CPU\n\ write operation.

-

LOG_STD_ACTION

MEM_ECC-2-BADADDR_SBE

2-Critical

Invalid ECC SBE dram address: 0x%08x latched by ECC Ctrl

The address latched by the ECC Ctrl when detecting a SBE is not a\n\ valid dram address. This kind of an error is not one that the\n\ ECC Ctrl shouldn't report under its normal operating conditions\n\ and when it does it most probably indicates a malfunctioning\n\ ECC Ctrl that needs replacement.

-

LOG_STD_ACTION

MEM_ECC-1-BADADDR_MBE

1-Alert

Invalid MBE dram address: 0x%08x latched by ECC Ctrl

The address latched by the ECC Ctrl when detecting an MBE is not a\n\ valid dram address. This kind of an error is not one that the\n\ ECC Ctrl shouldn't report under its normal operating conditions\n\ and when it does it most probably indicates a malfunctioning\n\ ECC Ctrl that needs replacement.

-

LOG_STD_ACTION

MEM_DDR-0-MS_ERR

0-Emergency

DDR Memory Select error detected at 0x%08x

This error is detected if the address from the memory request does \n\ not fall into any of the enabled programmed chip select address \n\ ranges. This could be a DDR configuration error or some application is\n\ trying to access an address for which the target is DDR but it's not \n\ within the configured address range

-

LOG_STD_ACTION

PQ3_TSEC-5-LOSTCARR

5-Notice

PQ3/FE[dec] Lost carrier. Transceiver problem?

The cable is not connected to the port.

hardware

"Connect the cable to the port."

PQ3_TSEC-5-LATECOLL

5-Notice

PQ3/FE[dec] Late collision

Late collisions occurred on the Ethernet/Fast Ethernet interface.

hardware

"If the interface is Fast Ethernet verify that both \ peers are in the same duplex mode. For regular \ Ethernet the system should recover. No action is\ required."

PQ3_TSEC-3-UNDERFLO

3-Error

PQ3/FE[dec] Transmit underflow

\ While transmitting a frame the controller chip's local buffer \ received insufficient data because data could not be transferred to the \ chip fast enough to keep pace with its output rate. Normally such a \ problem is temporary depending on transient peak loads within the \ system.

firmware

"The system should recover. No action is required."

PQ3_TSEC-4-BABBLE

4-Warning

PQ3/FE[dec] Babble error CSR[dec]=0x%04x

The transmitter has been on the \ channel longer than the time taken to transmit the largest \ frame.

hardware

"The system should recover. No action is required."

PQ3_TSEC-5-COLL

5-Notice

PQ3/FE[dec] Excessive collisions TDR=[dec] TRC=[dec].

-

-

-

CLOCK-3-HW_CAL_INVALID

3-Error

Hardware Calendar RTC Error.

The hardware calendar contains an invalid date. The accepted range\n\ is from 1993 to 2035.

me3600-me3800-sys

"To correct the invalid date use the <cmdBold>calendar set<noCmdBold>\n\ command and the <cmdBold>clock read-calendar<noCmdBold> command.\n"

NILE_PTP-3-MSGINITFAIL

3-Error

Failed to initalize required PTP resource: [chars]

During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated.

me3600-ptp

LOG_STD_ACTION

NILE_PTP-3-MSGDISPATCH

3-Error

Unable to dispatch received IPC message from PTP daemon

An unexpected condition has occurred while IOS was trying to dispatch a IPC message received from PTP daemon.

me3600-ptp

LOG_STD_ACTION

NILE_PTP-3-SP_STATUS_UPDATE

3-Error

PTP is down as PTP processor is rebooting

PTP is down as Sideband processor is rebooting. Saved PTP configuration will be applied again once SP is up.

me3600-ptp

LOG_STD_NO_ACTION

PLATFORM_NETWORK_CLOCK-4-ERROR

4-Warning

NULL

An unexpected condition has occurred.

me3600-3800-timing

LOG_STD_ACTION

SRCP_APP-6-PROCESS_CREATION_FAILED

6-Information

Cannot create SRCP application process\n

Failed to create the SRCP application process.

ios-voice

"Check the size of free memory to make sure there is enough memory."

SRCP_APP-6-SOCKET_OPEN_FAILED

6-Information

Failed to open UDP port for SRCP\n

Failed to open UDP port for the SRCP process.

ios-voice

"Check if any other application use the same UDP port number 2427."

SRCP_APP-6-DNS_QUEUE_FAILED

6-Information

Failed to create DNS message watched queue\n

Failed to create DNS message watched queue.

ios-voice

"Check the size of free memory to make sure there is enough memory."

SRCP_APP-6-SYS_QUEUE_FAILED

6-Information

Failed to create SRCP system message watched queue\n

Failed to create SRCP system message watched queue.

ios-voice

"Check the size of free memory to make sure there is enough memory."

SRCP_APP-2-INTERNAL_CRITICAL

2-Critical

[chars]

-

-

LOG_STD_SH_TECH_ACTION

SRCP_APP-3-INTERNAL_ERROR

3-Error

[chars]

-

-

LOG_STD_SH_TECH_ACTION

SRCP_APP-4-INTERNAL_WARNING

4-Warning

[chars]

-

-

LOG_STD_SH_TECH_ACTION

CERM-4-TUNNEL_LIMIT

4-Warning

Maximum tunnel limit of [dec] reached for Crypto functionality with \ securityk9 technology package license.

Maximum tunnel limit reached for Crypto functionality with securityk9 \ technology package license.

c2900

"Obtain 'hseck9' feature license and install it."

CERM-4-TLS_SESSION_LIMIT

4-Warning

Maximum TLS session limit of [dec] reached for Crypto functionality with \ securityk9 technology package license.

Maximum TLS session limit reached for Crypto functionality with \ securityk9 technology package license.

c2900

"Obtain 'hseck9' feature license and install it."

CERM-4-TX_BW_LIMIT

4-Warning

Maximum Tx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license.

Maximum Tx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license.

c2900

"Obtain 'hseck9' feature license and install it."

CERM-4-RX_BW_LIMIT

4-Warning

Maximum Rx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license.

Maximum Rx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license.

c2900

"Obtain 'hseck9' feature license and install it."

PLATFORM_HA-3-RF_REGISTRATION_FAILED

3-Error

Failed to register with RF rc = [dec]

Failed to register with RF during system initialization

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-NO_RCSF_PROCESS

3-Error

Failed to create process for rcsf deinit

Failed to create a process

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-4-RELOAD_PEER

4-Warning

Reloading the Standby due to [chars] [chars]

Application on the Active has requested a reload of the Standby.

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-4-RELOAD_PEER_FAILED

4-Warning

Failed to reload the Standby due to [chars] [chars]

-

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-4-RELOAD_SHELF

4-Warning

Reloading the shelf due to [chars] [chars]

Application on the Active has requested a reload of the shelf.

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-4-RELOAD_SHELF_FAILED

4-Warning

Failed to reload the shelf due to [chars] [chars]

-

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-SSO_FALLBACK_NOT_SUPPORTED

3-Error

Redundancy mode fallback to SSO is not supported

Cannot fallback to redundancy mode SSO

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-PLATFORM_RELOAD_PEER_FAILED

3-Error

Failed to send message to platform to request a peer reload

Unable to send a message to the platform

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-SPI_NOT_READY

3-Error

SPI is not ready cannot communicate with platform

Unable to communicate to the platform as SPI is not ready

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-SPI_INIT_FAILED

3-Error

Unable to initialize QEMU chassis SPI client

Failed to init QEMU chassis SPI client

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-CHASSIS_INIT_FAILED

3-Error

Failed to initialize QEMU chassis Interface

Failed to init QEMU chassis interface with platform

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-WATCHED_BOOLEAN_ROLE

3-Error

Failed to create watched boolean during init

Failed to allocate memory for watched boolean

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-SPI_PROCESS_CREATE

3-Error

Failed to create SPI process during init

Failed to create process to do SPI init

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-OIR_PROCESS_CREATE

3-Error

Failed to create OIR process during init

Failed to create process to do OIR init

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-OIR_INIT

3-Error

Failed to register with the OIR Library

Failed to register with the OIR Library

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-SLOT_ID_FAILED

3-Error

Failed to get the slot ID from OIR Library

Failed to get the slot ID from OIR Library

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-WATCHED_BOOLEAN_SLOT

3-Error

Failed to create watched boolean during init

Failed to allocate memory for watched boolean

QEMU_DDTS_COMPONENT

LOG_STD_ACTION

PLATFORM_HA-3-TRACE_INIT

3-Error

Cannot allocate the trace buffer for [chars]

Standby switch is being booted in the indicated fallback mode. Additional entries in log will indicate the reason for this action.

QEMU_DDTS_COMPONENT

LOG_STD_NO_ACTION

PLATFORM_HA-6-REDUNDANCY_MODE

6-Information

[chars] supervisor initializing for [chars] mode

Informational message regarding the redundancy mode of the supervisor

QEMU_DDTS_COMPONENT

LOG_STD_NO_ACTION

QA-3-ALLOC

3-Error

[chars]

This is a software error.

-

"Copy the error message exactly as it appears. Also copy the output of show version and show cont cbus. Contact your technical support representative."

QA-3-DIAG

3-Error

NULL

This is a diagnostic message.

-

"This message appears after a QA error and contains diagnostic information regarding that error. Copy the original QA error message and all the following QA diagnostic error messages exactly as they appear. Also copy the output of show version and show cont cbus. Contact your technical support representative."

CI-4-NOTFOUND

4-Warning

Chassis Interface not found

The system software could not detect the presence of a CI card.

-

"Verify that the CI card is correctly and fully installed in the backplane. If the error recurs call your technical support representative for assistance."

CI-3-SLOTCOMP

3-Error

Inconsistent [chars] slot %02x

The CI software detected a possible inconsistency in the CI hardware.

-

"Confirm that the CI card is correctly and fully installed in the backplane. If error recurs call your technical support representative for assistance."

CI-3-CTRLRTYPE

3-Error

Wrong controller type %02x

The CI was manufactured incorrectly.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

CI-2-INT

2-Critical

Unexpected interrupt - status %02x

An unexpected interrupt occurred. This is a serious software error which will be followed by a core dump.

-

LOG_STD_ACTION

CI-4-COND

4-Warning

Restarting with [dec] recent soft power shutdowns\n\t\tor system just powered-on

A soft shutdown occurs when the router powers itself down due to a detected over temperature condition. When the temperature goes up past the board shutdown trip point the cards are shutdown but the power supplies fans and CI continue to run. <body><par>When the system cools past the restart trip point the system will restart. The system counts the number of times this happens to keep the up/down cycle from repeating indefinitely. If the above counter reaches zero the system undergoes a hard shutdown which requires a power cycle to recover. The soft shutdown counter is reset to its maximum value after the system has been up for six hours.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

CI-3-NOACK

3-Error

[chars] acknowledge failure cmd %02x addr %02x data %02x

The CI software failed to communicate with the CI hardware.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

CI-6-BPLANE

6-Information

CI type [dec] differs from NVRAM type [dec]

The chassis type as reported by the CI is different from that programmed into NVRAM.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

CI-4-ENVWARN

4-Warning

[chars] measured at [chars]

One of the measured environmental test points exceeds the warning threshold.

-

"Closely monitor the condition and correct if possible. If the situation worsens call your technical support representative for assistance."

CI-2-ENVCRIT

2-Critical

[chars] measured at [chars]

One of the measured environmental test points exceeds an extreme threshold.

-

"Correct the specified condition or the router may shut itself down or fail to operate properly."

CI-6-PSCHANGE

6-Information

Power supply [dec] changed from [chars] to [chars]

The CI reported that a power supply was either installed removed or changed.

-

"If the situation does not correspond with a physical change in the system's power supplies call your technical support representative for assistance."

CI-3-PSFAIL

3-Error

Power supply [dec] failure

One of the router's power supplies failed.

-

"Replace the failed power supply as soon as possible."

CI-6-PSNORMAL

6-Information

Power supply [dec] normal

One of the router's failed power supplies are working normal now.

-

"If the situation does not correspond with a normal operation of the system's power supplies call your technical support representative for assistance."

CI-3-BLOWER

3-Error

[chars] fan failure

One of the router's cooling fans failed.

-

"Replace the fan as soon as possible or the router may shut itself down or fail to operate properly."

CI-1-BLOWSHUT

1-Alert

Blower failure shutdown in [dec] seconds

One of the six blowers in a five-slot chassis has failed. Because each blower cools a separate region of the cards in the chassis all blowers are needed for router operation. If a blower failure persists for 2 minutes the router will shut itself down and will need to be power cycled.

-

LOG_STD_ACTION

CI-4-MAXOUTPUT

4-Warning

Power supply [dec] [dec]V is at or near rated output

This indicates that the power supply is delivering its maximum rated current. This condition is not a problem unless the current continues to increase beyond the rated limit of the power supply which can cause hardware damage.

-

LOG_STD_ACTION

CI-4-SYSLOAD

4-Warning

System [dec]V load exceeds single power supply [dec] capacity

This warning message indicates that the system's electrical current usage exceeds the capacity of a single power supply. During this condition power supplies must not be removed from the system.

-

-

CI-4-UNBALANCE

4-Warning

Unbalanced [dec]V output from dual power supplies

The difference in electrical current output between the two power supplies is out of tolerance for the system design. One of the power supplies may be failing or about to fail.

-

LOG_STD_ACTION

QEM-3-DISCOVER

3-Error

Found [chars] switch processors

The QEM driver found either no switch processors or more than one. Exactly one is the only supported configuration.

-

"Make sure there is only one switch processor."

RSP-2-NOMEMORY

2-Critical

No memory available for [chars]

An attempt at memory allocation failed.

-

"Try these actions to remedy the problem: Add memory. Disable some features. Apply filtering to decrease the size of system data structures - the routing table for example. In general reduce other system activities to ease memory demands. If conditions warrant upgrade to a larger memory configuration."

RSP-2-BADCACHE

2-Critical

Overrun detected.\n End of MEMD buffer : 0x[hec]\n End of datagram : 0x[hec]\n bufhdr [hec]: %08x %08x %08x %08x\n Flushing Processor Cache

A packet was processed that was greater in size than the maximum possible MTU size or an illegal buffer header data area was found.

-

"Copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-FOREVER

3-Error

cmd [dec] to [chars] slot [dec] took [dec] usecs done [hec]

A command from the RSP to an IP took longer for the system to process than expected. This condition may be caused by a heavily loaded CPU.

-

"If this error recurs copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-2-QAERROR

2-Critical

[chars] error [chars] at addr %04x [chars]\n

While the system was attempting to process a hardware queue an error was detected by the QA ASIC. The error could be either a zero link error or a reuse error. A zero link error is caused by an attempt to place in the hardware queue a buffer header with an address of 0x0. A reuse error occurs when the QA ASIC detects or attempts to place in the hardware queue a buffer header that is the same as another buffer header in another hardware queue.\n Either of these errors can occur because of a software or hardware problem with the RSP or a line card.

-

"Run the show logging command and see that whether any parity errors were recorded just before the QAERROR error message was received. If any parity error was recorded before the QAERROR a hardware error has occurred. Copy the error message exactly as it appears on the console or in the system log contact your Cisco technical support representative and provide the representative with the gathered information. If no parity error was recorded and the problem recurs enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the output of the commands."

RSP-3-NOSTART

3-Error

No microcode for [chars] card slot [dec]

No microcode is defined or available for the specified card.

-

"Reconfigure the card to specify an existing microcode file."

RSP-3-XBUFHDR

3-Error

corrupt bufhdr [hec]: %08x %08x %08x %08x

A miscommunication occurred between the RSP and an IP.

-

"Copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-BADHWREV

3-Error

[chars] slot [dec] has wrong hardware revision [dec].[dec]

The hardware in the indicated slot needs to upgraded for operation with the RSP.

-

"Upgrade the board."

RSP-3-ERROR

3-Error

NULL

An internal software error has occurred. The exact nature of the problem is described in the error message.

-

"Copy the error message exactly as it appears on the console or in the system log contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-2-STALL

2-Critical

partially inserted or removed IPs on cyBus[dec]

The RSP detected a stall condition of cbus. Most likely a board is not fully seated in the chassis. A less likely possibility is a hardware problem with the RSP or backplane.

-

"Try reseating the boards. Call your technical support representative for assistance if this message persists."

RSP-3-IDPROM

3-Error

Bad or missing ID EEPROM controller type [dec]

The ID EEPROM on the RSP is missing or bad.

-

"This message indicates a manufacturing error. Report this error to your technical support representative."

RSP-3-NOMAC

3-Error

Can't allocate MAC address for interface [dec]/[dec]

No MAC address was available for allocation to the specified interface.

-

"Report this error to your technical support representative."

RSP-4-COOKIE

4-Warning

Corrupt or missing MAC address cookie\n using random base [enet]

This message indicates the part containing the MAC addresses allocated to this chassis could not be accessed or was found to be corrupt either due to a hardware problem or manufacturing problem.

-

"Report this error to your technical support representative."

RSP-3-RESTART

3-Error

NULL

The cBus buffer memory has been reset and reallocated. The exact nature of the problem is described in the error message.

-

-

RSP-4-SLAVETIME

4-Warning

[chars]

Report this error to your technical support representative.

-

-

RSP-3-LOVEGIANT

3-Error

Card [chars] wants [dec] byte love letters but only got [dec] bytes

An inconsistency between the microcode and the system code was detected.

-

"Report this error to your technical support representative."

RSP-3-LOVENOTE

3-Error

[hec] corrupt: %08x %08x %08x %08x

The event handler at the RSP has detected a status update message from an interface processor but the field in the status message that identifies the associated interface processor is not valid. This condition indicates that the status message is corrupted. This error could occur because of a hardware or a software problem.\n The address of the status message buffer and the first four words of the message will be displayed for diagnostic purposes.

-

"Copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-NOIDB

3-Error

bad vc [dec] on [chars]

A chennelized interface driver received a packet on an unconfigured channel.

-

"Copy the error message exactly as it appears and report it to your " "technical support representative along with the output of " "'show tech-support'."

RSP-3-IP_PANIC

3-Error

Panic: [chars] %08x %08x %08x %08x

The status message handler for the interface processor has detected that the firmware for the interface processor has experienced a critical condition. The name of the affected interface and the first four words of the status message buffer will be displayed along with the message for diagnostics

-

"Copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-NORESTART

3-Error

[chars]: unable to schedule restart for output queue

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

RSP-3-INVRTN

3-Error

Invalid return queue\n next=[hex] hwidb=[hex] type=[hex]\n queue_ptr=[hex] bufhdr_offset=[hex] id=[dec] bcast_id=[dec]\n bufhdr [hec]: %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

RSP-3-INVRTNBCASTID

3-Error

Invalid return queue bcast_id=[dec]\n bufhdr [hec]: %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

RSP-3-INVQPTR

3-Error

queue=[hex] bufhdr [hec]:\n %08x %08x %08x %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

RSP-3-BADBUFHDR

3-Error

[chars] address [hec]

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

RSP-3-IPC

3-Error

[chars] [chars]

An IPC error has occurred. The exact nature of the problem is described in the error message.

-

"Copy the router configuration along with any other relevant information. Copy the error message exactly as it appears on the console or in the system log contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-SLAVECHANGE

3-Error

Slave changed state from [chars] to [chars]

The slave RSP has undergone a hardware state change. Both the old state and new state are shown. Possible states are nonparticipant slave master unplugged Possible state changes indicated by the above message are any to unplugged unplugged to nonparticipant or slave nonparticipant to slave slave to nonparticipant Any other combination is unexpected.

-

-

RSP-5-SLAVEUP

5-Notice

Slave changed to state Running Buffer memory state : [chars]

This is an informational message to indicate that the slave RSP has started running the slave RSP image. This message after the router boots or after the slave reload global configuration command is issued on the master RSP.

-

"No action required."

RSP-3-MSFIX

3-Error

Fixing [chars] by setting to default [chars]

The characters shown can be either on the slave RSP setting or on the master RSP setting. The ROM monitor default slave RSP setting is not synchronized with the system configuration file specifications. During bootup the system image detects the mismatch and modifies the ROM monitor setting to conform with these specifications. This mismatch most likely occurred because a new RSP was being installed and booted in a high system availability HSA environmentmsgdef_recommended_action Using the show version or show boot command

-

-

RSP-3-MSVERS

3-Error

Master has m/s version [dec] slave has m/s version [dec]

The master and slave are running incompatible software versions with regards to the master/slave exchange process.

-

"If the slave image global configuration is used to override the default slave image from the bundle then the slave image is incompatible. Update either the master or slave image to ensure the two are compatible. If the slave is running the image from the bundle execute and record the output of show version show running-config and show controller cbus commands. Report this information and the error message to your technical support representative."

RSP-3-MSDOG

3-Error

Master/slave watchdog timed out

While handling the interrupts from the DBUS FPGA the RSP has detected that the timeout bit in the interrupt status register has been set. This condition indicates that the master RSP no longer controls the CBUS and DBUS. The slave may become active during this time. So the rest of the interrupt handler will not be processed.\n This behavior could be the result of either a hardware or a software problem.

-

"Copy the error message exactly as it appears. If this problem recurs copy down the router's configuration along with any other relevant information such as the output of show tech-support and show logging commands. Contact your Cisco technical support representative for assistance and provide him with all the gathered information."

RSP-3-SLAVEMASTER

3-Error

Slave stole mastership

The master RSP has detected that the slave RSP configuration was changed from slave to master. The old master RSP will reload and become the slave RSP allowing the new master RSP take over. This behavior indicates a software or hardware error.

-

"Copy the router configuration along with any other relevant information. Copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-SLAVE_NVRAM_BUSY

3-Error

Slave NVRAM is temporarily busy

Another process is temporarily locking the slave config.

-

"Retry the command that caused the error message. If the error message recurs check for other execs via the show users command. If you know that there are no other users locking the slave nvram then contact your technical support representative for assistance."

RSP-4-HSA_MEM

4-Warning

size mismatch master [dec]MB slave [dec]MB

Memory size mismatch between Master & Slave RSP.

-

"Configure both Master and Slave RSPs to have an equal amount of memory."

RSP-4-HSA_MINMEM

4-Warning

[dec]MB required for HSA

HSA requires a minimum of 24mb of memory.

-

"Upgrade your system to meet minimum memory requirements for HSA."

IPC_RSP_CBUS-3-INVNUM

3-Error

[chars] [dec]

The IPC application tried to send a message that was larger than IPC could handle. The message was not transmitted.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

IPC_RSP_CBUS-3-SEATERR

3-Error

[chars] [dec]

The ID associated with an IPC card is either missing duplicated or cannot be created.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

IPC_RSP_CBUS-3-CARDERR

3-Error

[chars]

An IPC card has registered itself to the IPC master twice. The card malfunctioned and its IPC is not active.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

IPC_RSP_CBUS-3-MSGERR

3-Error

[chars] [dec]

System controller Bengal has reported an error/event

RSP

"Read error reports. SBE are generally not fatal. Most others are"

IPC_RSP_CBUS-3-NOHWQ

3-Error

Hardware queue for card at slot [dec] not found

IPC messages cannot be transmitted due to a missing hardware queue. The messages were discarded and subsequent messages will not be transmitted to that card.

-

"Copy the error message exactly as it appears and report it to your technical support representative."

RSP-3-BADTURBOIPCMSG

3-Error

Bad Turbo IPC msg [chars]: msg=[hex] lastmsg=[hex] hdrsize=[hex] size=[hex]

An error was discovered in an IPC message.

-

LOG_STD_ACTION

IPC_RSP_CBUS-3-NOBUF

3-Error

[chars]

The IPC ran out of memory device MEMD buffers.

-

"Reduce the number of applications currently running on the IPC. Copy the error message exactly as it appears and report it to your technical support representative."

RSP-2-QADIAG

2-Critical

QA Diagnostic [chars] error at %#08x

An error occurred during an attempt to access the RSP.

-

"Copy the error message exactly as it appears on the console or in the system log enter the show tech-support and show logging commands contact your Cisco technical support representative and provide the representative with the gathered information."

RSP-3-ACCERROR

3-Error

[chars] acc %08x had bad value [dec]

An incorrect value has been written on an accumulator.

-

"Copy the error message exactly as it appears and report it to your technical support representative. A micro reload can correct the error condition as a workaround."

RSP-4-RSPDRAM

4-Warning

Insufficient DRAM to adequately run this IOS version. [dec]M is recommended.

The quantity of RSP DRAM is below the recommended amount.

-

"Add DRAM."

RSP-4-SLAVENOTUPDATED

4-Warning

Slave configuration not updated for [chars].

The configuration on the slave cannot be synced with the master.

-

"Ensure that 'slave auto-sync config' is configured and that the slave is active"

RSP-3-SLAVECOPYFAILED

3-Error

Copy of [chars] failed [chars].

-

-

-

RSP-4-DCEFSWITCHENABLE

4-Warning

DCEF switching should be enabled on member links of [chars]

DCEF should be enabled for Multilink interfaces if required.

-

"Go to the multilink interface configuration mode using the <CmdBold>interface multilink multilink# <noCmdBold> command and then enable DCEF on the interface using <CmdBold> ip route-cache distributed<noCmdBold> as per your requirement"

RSP-3-BENGAL

3-Error

Bengal error. [chars]

System controller Bengal has reported an error/event

RSP

"Read error reports. SBE are generally not fatal. Most others are"

RSP-4-EMPTY_VIPBAYS

4-Warning

VIP in slot [dec] was empty and was disabled

The system failed to copy the specified file to the standbyRSP.

rsp

"Ensure that the standby RSP exists and has enoughmemory for the file."

RSP-3-NORELOAD

3-Error

reload command not allowed on standby RSP

The <CmdBold>reload<NoCmdBold> command in exec mode is not allowed on thestandby RSP

rsp

"Enter the <CmdBold>slave reload<NoCmdBold> commandin exec mode."

RSP-6-TXSTUCK

6-Information

Txacc of Interface [chars] is at [dec]%% of its txlimit

The specified interface has a low txacc value. This might be a transient condition and harmless if it occurs in periods of high packet traffic. If it occurs more than once in periods of relatively moderate traffic it could indicate a problem Distributed packet switching might be disrupted as a result of this condition.

RSP

"If the message recurs during periods of relatively" "moderate traffic this might indicate disruption" "in distributed packet switching. If such a disruption" "occurs use a <CmdBold>microcode reload<NoCmdBold> to" "recover. Open a case with the Technical Assistance Center" "via the Internet at" "www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl" "or contact your Cisco technical support representative" "and provide the representative with the information you" "have gathered. Attach the following information to your" "case in non-zipped plain-text .txt format: the output"

RSP-4-CRASHINFO

4-Warning

Error saving crashinfo for slot [dec]. Reason: [chars]

A VIP crashinfo file has not been saved due to the indicated reason.

rsp

"If the reason indicates <CmdBold>Out of space" "<NoCmdBold> the bootflash may not have sufficient memory " "to save the crashinfo file. Otherwise open a case with " "the Technical Assistance Center via the Internet at " "www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "or contact your Cisco technical support representative " "and provide the representative with the information you " "have gathered. Attach the following information to your " "case in non-zipped plain-text .txt format: the output "

RSP-3-PA_INIT

3-Error

Malloc to [chars] failed for slot [dec] bay [dec]

The information structure for the port adapter could not be created. The interfaces on the specified port adapter might no longer be functional. A possible reason for this is a memory allocation failure involving the port adapter. This can occur as a result of insufficient hardware memory or a memory leak.

rsp

"Please confirm that the recommended amount of memory is installed " "for the platform. If memory is adequate please get the output of " "<CmdBold>show process memory<NoCmdBold> over time to determine the " "process using increased memory. As an immediate possible solution " "please attempt to reseat the line card. If this condition persists " LOG_STD_SH_TECH_ACTION

RSP_ISSU-6-ISSU_QUIESCED

6-Information

Slot [dec] is ISSU quiesced and it will be performing MDR

The line card in the specified slot has been prepared for minimal disruptive restart. The card will be performing a minimal disruptive restart when a switchover occurs.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-2-IPC_ERROR

2-Critical

[chars]

This is a critical error message about an error that has occurred in IPC communication while performing the ISSU operations in the system. A message of this type indicates that a failure has occurred during IPC communication while performing an ISSU upgrade.

issu-7500

"Copy the notice exactly as it appears. Check both the active system and " "standby system for messages. Collect the output of " "<CmdBold>show ipc status<NoCmdBold>. Call your technical support " "representative for assistance and provide him with the information " "collected. "

RSP_ISSU-2-IPC_PORTOPEN_ERROR

2-Critical

Failed to open \[chars]\ port. Reason=[chars]

This is a critical error message about an error that has occurred in IPC communication while performing the ISSU operations in the system. A message of this type indicates that a failure has occurred during opening an IPC port while performing an ISSU upgrade.

issu-7500

"Copy the notice exactly as it appears. Check both the active system and " "standby system for messages. Collect the output of " "<CmdBold>show ipc ports<NoCmdBold>. Call your technical support " "representative for assistance and provide him with the information " "collected. "

RSP_ISSU-2-IPC_SEND_ERROR

2-Critical

Failed to send ISSU IPC message [dec]

This is a critical error message about an error that has occurred in IPC communication while performing the ISSU operations in the system. A message of this type indicates that a failure has occurred during sending an IPC message while performing an ISSU upgrade.

issu-7500

"Copy the notice exactly as it appears. Check both the active system and " "standby system for messages. Call your technical support representative " "for assistance."

RSP_ISSU-2-IMG_DNLD_ERROR

2-Critical

[chars]

This is a critical error message about an error that has occurred in Image Predownload while performing the ISSU operations in the system. A message of this type indicates that a failure has occurred during image predownload to VIP while performing an ISSU upgrade.

issu-7500

"Copy the notice exactly as it appears. Check both the active system and " "standby system for messages. Call your technical support representative " "for assistance."

RSP_ISSU-2-IMG_RCV_ERROR

2-Critical

[chars]

This is a critical error message about an error that has occurred in Image Predownload while performing the ISSU operations in the system. A message of this type indicates that a failure has occurred during receiving the VIP image on the active RP while performing an ISSU upgrade.

issu-7500

"Copy the notice exactly as it appears. Check both the active system and " "standby system for messages. Call your technical support representative " "for assistance."

RSP_ISSU-2-IMG_SEND_ERROR

2-Critical

[chars]

This is a critical error message about an error that has occurred in Image Predownload while performing the ISSU operations in the system. A message of this type indicates that a failure has occurred during sending the VIP image from standby RP while performing an ISSU upgrade.

issu-7500

"Copy the notice exactly as it appears. Check both the active system and " "standby system for messages. Call your technical support representative " "for assistance."

RSP_ISSU-5-IMG_SEND_DONE

5-Notice

Image Send to Active RP is complete

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that the image send to active RSP has been completed.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-4-LC_RESET

4-Warning

linecard in slot [dec] will be reset during MDR

This is an informative message regarding the VIP minimal disruptive restart functionality. This error message indicates that the line card specified in the given slot will get reset during the ISSU process and there will be extended downtime during the upgrade process.

issu-7500

"Please verify whether the line card in the given slot supports " "minimal disruptive restart as per the feature navigator tool. " "If it doesnt then no action is required. Otherwise " "please call your technical support representative " "for assistance. "

RSP_ISSU-5-IMG_DNLD_STARTED

5-Notice

MDR Image download has started.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that MDR image download has started.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-5-IMG_DNLD_ABORTED

5-Notice

MDR Image download has been aborted.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that MDR image download has been aborted.

issu-7500

"If you did not abort the download process gather the " "system messages that preceded this message to help " "the TAC representative diagnose the system condition. "

RSP_ISSU-5-IMG_DNLD_COMPLETE

5-Notice

Slot [dec] has received MDR image successfully

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that the line card specified in the given slot has completed image download.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-5-IMG_RCV_DONE

5-Notice

Image has been received completely from standby.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that the image receive from standby RSP has been completed.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-5-IMG_DNLD_DONE

5-Notice

Image Download process complete.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that the image predownload process has been completed.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-4-ISSU_NO_QUIESCE

4-Warning

linecard in slot [dec] is not ISSU quiesced.

This is an informative message regarding the VIP minimal disruptive restart functionality. This error message indicates that the line card specified in the given slot will get reset during the ISSU process and there will be extended downtime during the upgrade process.

issu-7500

"Please verify whether the line card in the given slot supports " "minimal disruptive restart as per the feature navigator tool. " "If it doesnt then no action is required. Otherwise " "please call your technical support representative " "for assistance. "

RSP_ISSU-5-VIP_MDR_STARTED

5-Notice

Slot [dec] has started doing MDR.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that given slot has started MDR successfully.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-5-VIP_MDR_FINISHED

5-Notice

Slot [dec] has finished doing MDR.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that given slot has finished MDR successfully.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-3-VIP_MDR_FAILED

3-Error

Slot [dec] has failed to complete MDR.

This message indicates a problem with minimal disruptive restart functionality on the VIP. The specified slot failed to complete MDR because of a checksum error or an internal crash.

issu-7500

"Verify if the card in the specified slot supports " "MDR. Verify that the card is inserted properly. " "If condition persists gather the output of " "<CmdBold>show tech-support<noCmdBold>. Contact your " "technical support representative with the gathered" "information. "

RSP_ISSU-3-VIP_MDR_NOSTART

3-Error

Slot [dec] Couldnt start MDR.

This is an error message regarding the VIP minimal disruptive restart functionality. This message indicates that given slot has failed to start MDR.

issu-7500

"please verify whether the card in the slot supports " "MDR and whether it is inserted properly in the box. " "Collect the output of <CmdBold>show tech-support<noCmdBold> " "and please call your technical support representative " "for assistance. "

RSP_ISSU-5-VIP_MDR_READY

5-Notice

Slot [dec] is ISSU quiesced and ready to do MDR.

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that given slot has finished ISSU quiesce and is ready to perform MDR.

issu-7500

"The system is behaving normally. No action is required."

RSP_ISSU-5-VIP_MDR_ABORTED

5-Notice

MDR has aborted on slot [dec].

This is an informative message regarding the VIP minimal disruptive restart functionality. This message indicates that given slot has aborted MDR preparations. This could have happened if the user has initiated a abortversion command.

issu-7500

"If you did not abort the download process gather the " "system messages that preceded this message to help " "the TAC representative diagnose the system condition. "

RSP_ISSU-3-ISSU_CCB_FAIL

3-Error

[chars] [dec]

RSP ISSU CCB Playback System Error. There was a Playback Error encountered in the CCB Playback on the Standby.

issu-7500

"Copy the message exactly as it appears. Check both the active system " "and standby system for messages. Get the output with <CmdBold>debug " "issu ccb-playback<NoCmdBold> enabled and then call your technical " "support representative for assistance."

RSP_ISSU-3-MSG_NOT_OK

3-Error

[chars] ISSU Client [dec] message type [dec] is not ok

RSP HA ISSU Client message type has not negotiated correctly

issu-7500

show issu message types <Client_ID>

RSP_ISSU-3-XMIT_XFORM_FAIL

3-Error

[chars] ISSU Client transmit transformation has failed for message [dec]

RSP HA ISSU Client message transmit side transformation has failed

issu-7500

LOG_STD_ACTION

RSP_ISSU-3-RCV_XFORM_FAIL

3-Error

[chars] ISSU Client receive transformation has failed for message [dec]

RSP HA ISSU Client message receive side transformation has failed

issu-7500

LOG_STD_ACTION

RSP_ISSU-3-XFORM_MALLOC_FAIL

3-Error

[chars] ISSU Client malloc [dec] has failed

RSP HA ISSU Client cannot allocate memory for the data to be transformed and sent across to the peer. Most likely a resource problem within the system.

issu-7500

LOG_STD_REDUCE_ACTION

RSP_ISSU-3-GET_BUFFER

3-Error

[chars] ISSU Client session [dec] failed to get buffer

RSP HA ISSU Client failed to get a buffer

issu-7500

LOG_STD_REDUCE_ACTION

RSP_ISSU-3-MSG_SEND

3-Error

[chars] ISSU Client session [dec] failed to send message

RSP HA ISSU Client failed to send negotiation message to peer

issu-7500

LOG_STD_ACTION

RSP_ISSU-3-MSG_MTU

3-Error

[chars] ISSU Client [dec] get message MTU failed for message [dec].

RSP HA ISSU Client get message MTU Maximum Transmission Unit failed

issu-7500

LOG_STD_ACTION

RSP_ISSU-3-SESSION_UNREG

3-Error

[chars] ISSU Client session [dec] un-registration failed

RSP HA ISSU Client session un-registration failed

issu-7500

show issu sessions <Client_ID>

RSP_ISSU-3-SESSION_REG

3-Error

[chars] ISSU Client session [dec] registration failed

RSP HA ISSU Client session registration failed

issu-7500

show issu sessions <Client_ID>

C5RSP-3-C5_MACADRFAIL

3-Error

can't get C5 Line Card Mac Addr

An attempt by the RSP to query the C5IP for Vlan 0 IP address failed.

-

"Try these actions to remedy the problem: Reset the router from the NMP's console. If problems persist please RMA the router and or Catalyst 5000"

C5RSP-3-C5_NMPMACADRFAIL

3-Error

can't get NMP Mac Addr

An attempt by the RSP to query the C5IP for Vlan 0 MAC address failed.

-

"Try these actions to remedy the problem: Reset the router from the NMP's console. If problems persist please contact Cisco for replacement"

C5RSP-3-C5_SAGE0FAIL

3-Error

Length error occurred on dma channel 0

A hardware error has occurred on dma channel 0

-

"Report this error to your technical support representative."

C5RSP-3-C5_SAGE1FAIL

3-Error

Length error occurred on dma channel 1

A hardware error has occurred on dma channel 1

-

"Report this error to your technical support representative."

C5RSP-3-C5IP_SLOTFAIL

3-Error

can't get Catalyst 5000 Slot number of router

An attempt by the RSP to query the C5IP for theslot it is plugged into has failed.

-

"Try these actions to remedy the problem: Reset the router from the NMP's console. If problem persists please contact Cisco for replacement."

C5RSP-3-CANT_CREATE_VLAN

3-Error

vlan [dec] can not be created. media not supported

An attempt to create a vlan of a media that is not supported has failed

-

"Try these actions to remedy the problem: Configure the vlan with a different media type."

C5RSP-6-BRIDGE_AFU

6-Information

vlan [dec] could/could not be configured for bridging

A Vlan could not be reset with the proper bridging information.

-

"Try these actions to remedy the problem: Configure the vlan with or with bridging."

C5RSP-6-VLAN_INFO_MISSING

6-Information

vlan [dec] info errant. something very wrong

Internal information about the Vlan is missing.

-

LOG_STD_ACTION

C5RSP-6-NOSWIDB

6-Information

vlan [dec] missing IDB

Internal data structure of the Vlan is missing.

-

LOG_STD_ACTION

C5RSP-3-MAXVLAN_EXCEEDED

3-Error

can't configure more than 256 VLANS

The Vlan Router product can configure a maximum of 256 vlans.

-

"Try these actions to remedy the problem: Delete unused vlans before configure new ones."

C5RSP-3-C5_BADIPC

3-Error

bad message received from the NMP

An unsolicited in band IPC message was received by the router from the NMP.

-

LOG_STD_NO_ACTION

C5RSP-3-NMP_PROG_FAIL

3-Error

NMP won't allow vlan [dec] configuration

In band IPC message to the NMP from the router to create a vlan has failed.

-

"Try these actions to remedy the problem: Check the state of Vlan 0. Check the state of the C5IP via the front panel LED. Check the state of the NMP. Reset the router"

C5RSP-3-NMP_INIT_FAIL

3-Error

can't talk to NMP during initialization

In band IPC router initialization message to the NMP has failed

-

"Try these actions to remedy the problem: Check the state of Vlan 0. Check the state of the C5IP via the front panel LED. Check the state of the NMP. Reset the router"

C5RSP-3-UNKNOWN_NMP_PROG

3-Error

unknown timer for NMP programming

An unknown timer event has expired.

-

LOG_STD_NO_ACTION

C5RSP-3-NMP_DELETE_VLAN

3-Error

having problems deleting vlan [dec] on the NMP

In band IPC message to the NMP from the router to delete a vlan has failed.

-

"Try these actions to remedy the problem: Check the state of Vlan 0. Check the state of the C5IP via the front panel LED. Check the state of the NMP. Reset the router"

C5RSP-3-INVALID_LOVE_LETTER

3-Error

Invalid loveletter type [dec] sent by c5ip\n

IOS is receiving bogus messages from the C5IP.

-

LOG_STD_RECUR_ACTION

C5RSP-3-RSM_NMP_CONFIG_MISMATCH

3-Error

RSM NMP mismatch in config for [dec] RSM [dec] NMP [dec]\n

There is mismatch in config for this vlan on NMP and RSM

-

"Make sure that the params for this vlan are the same on NMP and on the RSM"

C5RSP-3-RSM_NMP_BRIDGE_INVALID

3-Error

NMP returned invalid bridge id [dec] for [dec]\n

NMP returned invalid bridge id to the RSM

-

"Make sure that the tr-brf vlan on the RSM is configured on the NMP"

HA-2-CUTOVER_ERROR

2-Critical

[chars]

This is a critical error message about a High Availability System cutover status or condition. A message of this type indicates that a critical failure occurred during cutover of the standby system to the active system. Messages of this type indicate that the active system relinquished system control that the standby system failed to properly take over as the active.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-2-CUTOVER_NOTICE

2-Critical

[chars]

This is an important High Availability System notice logging the state of a system cutover of the standby system to the active system. Messages of this type indicate that the active system reliquished system control and that the standby system is taking over as active.

-

"If the message is due to a failure condition copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance. If the message is not due to a failure condition no action is required."

HA-2-NO_QUIESCE

2-Critical

Slot [dec] did not quiesce it will be disabled and then reloaded.

This is a cutover notice about a High Availability System linecard error condition. The linecard did not quiesce properly.

-

"This message is normal if the slot contains a legacy IP. Otherwise copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-2-MAX_NO_QUIESCE

2-Critical

[dec] linecards not quiesced exceeds limit of [dec] all slots will be reloaded.

-

-

"If you OIR removed the active RSP or have legacy IPs installed in the system this message is normal. Otherwise copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-2-IPC_ERROR

2-Critical

[chars] [chars]

This is a critical error message about a High Availability System interprocess communication status or condition. A message of this type indicates that an interprocess communication failure occurred between the active system and the standby system.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-2-INIT_ERROR

2-Critical

[chars]

This is a critical error message about a High Availability System initilization status or condition. A message of this type indicates that a failure occured during high availability system initialization.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-3-ERROR

3-Error

[chars]

This is a error message about a High Availability System status or condition.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-2-CCB_PLAYBACK_ERROR

2-Critical

CCB playback failed.

This is a critical error message about a High Availability System status or condition.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-2-CCB_RECORD_ERROR

2-Critical

CCB record failed.

This is a critical error message about a High Availability System status or condition.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-3-SYNC_ERROR

3-Error

[chars]

This is a error message about a High Availability System state syncronization error status or condition.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-5-SYNC_NOTICE

5-Notice

[chars]

This is a notice message about a High Availability System syncronization status condition or event.

-

"No action required."

HA-5-SYNC_RETRY

5-Notice

Reloading standby and retrying sync operation retry [dec].

This is a notice message about a High Availability System syncronization status condition or event. The syncronization operation will be retried.

-

"No action required."

HA-5-SYNC_RETRY_FAIL

5-Notice

Maximum sync retries exceeded. Reloading standby and cancelling sync.

This is a notice message about a High Availability System syncronization status condition or event. The syncronization operation failed.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-4-WARNING

4-Warning

[chars]

This is a warning message about a High Availability System status condition or event.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-5-NOTICE

5-Notice

[chars]

This is a notice message about a High Availability System status condition or event.

-

"No action required."

HA-5-HWMOD_IMG_NOTICE

5-Notice

[chars] hw-module slot [dec] image [chars] : [chars]

This is a notice message about a High Availability System hardware module configuration status condition or event.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-5-MODE

5-Notice

Operating mode is [chars] [chars]mode is [chars].

This is a notice about the High Availablility System mode.

-

"Make sure that both the active system and standby systems are correctly configured and operational."

HA-5-HA_VERSION

5-Notice

Active HA version [dec].[dec] differs from standby HA version [dec].[dec]

This is a notice about High Availablility System version mismatch between the active and standby systems.

-

"No action required."

HA-5-HA_IOS_VERSION

5-Notice

Active IOS version differs from standby IOS version

This is a notice about High Availablility System version mismatch between the active and standby systems.

-

"No action required."

HA-4-CONFIG_NOT_LOCKED

4-Warning

Unable to lock the configuration session.

This is a warning message indicating that the configuration session could not be locked. Simultaneous configuration sessions can corrupt the configuration.

-

"Copy the message exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

HA-5-RF_RELOAD_NOTICE

5-Notice

Unable to reload the standby. [chars]

The active RSP was unable to reload the standby because of the reason indicated in the message. This may be because the slave is in unplugged state or because there is a redundancy forced switchover process in progress or because the reload function is incorrectly called from the standby to the active.

-

-

HA-3-RF_EVENT_FAILED

3-Error

RF event not processed till [dec] milliseconds. Code = [dec]

The event sent to the redundancy facility was not processed till the specific time delay.

-

"Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance."

SIBYTE-3-SB_UNINITIALIZED_INT

3-Error

Uninitialized interrupt 0x%016llx

An uninitialized interrupt was received

procyon

LOG_STD_ACTION

SIBYTE-3-SB_SPURIOUS_INT

3-Error

Spurious interrupt level [dec]

A spurious interrupt was received

procyon

LOG_STD_ACTION

SIBYTE-3-SB_UNEXPECTED_INT

3-Error

Unexpected interrupt at level [dec] 0x%016llx

An unexpected interrupt was received

procyon

LOG_STD_ACTION

SIBYTE-2-SB_MAC_FATAL

2-Critical

Fatal Error on mac [dec] 0x%016llx

A fatal error occurred on a MAC interface

procyon

LOG_STD_ACTION

SIBYTE-6-SB_RMON_OVRFL

6-Information

RMON register [dec] overflow on mac [dec]

An RMON statistics register has been wrapped around

procyon

LOG_STD_NO_ACTION

SIBYTE-5-SB_OUT_OF_RX_DSCR_CH0

5-Notice

Out of RX descriptors on mac [dec] - channel 0 count: %lld

-

-

-

SIBYTE-5-SB_OUT_OF_RX_DSCR_CH1

5-Notice

Out of RX descriptors on mac [dec] - channel 1 count: %lld

-

-

-

SIBYTE-3-SB_RX_FIFO_UNDRFL

3-Error

RX FIFO underflow on mac [dec] count: %lld

-

-

-

SIBYTE-3-SB_RX_FIFO_OVRFL

3-Error

RX FIFO overflow on mac [dec] count: %lld

-

-

-

SIBYTE-3-SB_TX_FIFO_UNDRFL

3-Error

TX FIFO underflow on mac [dec] count: %lld

-

-

-

SIBYTE-3-SB_TX_FIFO_OVRFL

3-Error

TX FIFO overflow on mac [dec] count: %lld

-

-

-

SIBYTE-4-SB_LATE_COLL

4-Warning

Late collision on mac [dec] count: %lld

-

-

-

SIBYTE-4-SB_EXCESS_COLL

4-Warning

Excessive collisions on mac [dec] count: %lld

-

-

-

SIBYTE-3-SB_MAC_ERROR

3-Error

Unrecognized error on mac [dec] 0x%016llx

Unrecognized error on MAC interface

procyon

LOG_STD_ACTION

SIBYTE-0-ADDRESS_TRAP

0-Emergency

Address trap: [dec] occurred on physical address: 0x%llx at EPC: 0x[hec] ERR_EPC: 0x[hec]

A previously defined address trap has occurred.

debug

"Copy the error message exactly as it appears and report it to your technical support representative."

SIBYTE-0-UNCORRECTABLE_ECC_ERR

0-Emergency

An uncorrectable ECC error has occurred A_BUS_L2_ERRORS: 0x%llx A_BUS_MEMIO_ERRORS: 0x%llx A_SCD_BUS_ERR_STATUS: 0x%llx

An uncorrectable ECC error has occurred.

debug

"Copy the error message exactly as it appears and report it to your technical support representative."

SIBYTE-3-CORRECTABLE_ECC_ERR

3-Error

A correctable ECC error has occurred A_BUS_L2_ERRORS: 0x%llx A_BUS_MEMIO_ERRORS: 0x%llx A_SCD_BUS_ERR_STATUS: 0x%llx

A correctable ECC error has occurred.

debug

"Copy the error message exactly as it appears and report it to your technical support representative."

SIBYTE-0-MISDIRECTED_INTERRUPT

0-Emergency

A misdirected interrupt occurred with int_mask: 0x[hec]

A misdirected interrupt occurred.

debug

"Copy the error message exactly as it appears and report it to your technical support representative."

DMA-1-LOW_DMA_PCI_MEM

1-Alert

Not enough pci memory left over for DMA

Misconfiguration has resulted in overutilization of PCI memory

high-vip2

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of show diag and show controller cbus"

DMA-1-LOW_DMA_PROC_MEM

1-Alert

Not enough processor memory left over for DMA

This error message appears only in custom built images when a sanity\n\ check fails. A packet that was too large was sent over the backplane\n\ by a VIP.

high-vip2

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of show tech."

DMA-1-DRQ_STALLED

1-Alert

DRQ stalled. Dumping DRQ.

The path from VIP to backplane has stalled. The DRQ table is \n\ being dumped for debugging

high-vip2

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the hex\n\ dump following this message"

DMA-1-DRQ_EMPTY_PAK

1-Alert

Empty packet is being sent to backplane. particle_ptr=[hex]

drq_io receives a packet that has particle count 0. coding error --\n\ hurt performance

high-vip2

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the\n\ show log on the reporting VIP"

DMA-3-DTQ_DISPATCH_DIRTY_PAK

3-Error

pak not cleaned up by Egress processing appId [dec]

After dtq dispatched a packet to Egress processing packet is not cleaned up by application

high-vip2

"Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the\n\ show log on the reporting VIP"

LICENSE_C5920-6-DEFAULT_BANDWIDTH_ACTIVATED

6-Information

Forwarding bandwidth limited to [dec] Kbps

Default bandwidth activated its state is 'In Use' . Traffic forwarding will be rate limited

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-4-DEFAULT_BANDWIDTH_NOT_ACTIVATED

4-Warning

Unable to forward bandwidth to [dec] Kbps. Reason: [chars]

Default bandwidth was not activated due to the condition noted in the message.

SWR_DDTS_COMPONENT

"Based on the message reason ensure that the " "conditions required to activate default bandwidth " "is met."

LICENSE_C5920-6-LICENSE_ACTIVATED

6-Information

Installed license for feature [chars] now in use. Forwarding bandwidth limited to [dec] Mbps

A valid license was installed and activated its state is 'In Use' . Traffic forwarding will be rate limited

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-6-UNLIMITED_LICENSE_ACTIVATED

6-Information

Installed license for feature [chars] now in use.

A valid license was installed and activated its state is 'In Use'.

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-6-LICENSE_DEACTIVATED

6-Information

License for feature [chars] is no longer in use.

The state of the feature license is now 'Not in Use'.

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-3-ACTIVATION_ERROR

3-Error

Activation of license for feature [chars] failed. Error code: [dec]

An error occurred while attempting to activate a license that was just installed.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-4-NOT_ACTIVATED

4-Warning

Installed license for feature [chars] was not placed in use. Reason: [chars]

A valid license was installed but was not activated its state was not moved to 'In Use' due to the condition

SWR_DDTS_COMPONENT

"Based on the message reason ensure that the " "conditions required to activate the license are " "met. This may require the installation of a " "different license."

LICENSE_C5920-4-NO_ACTIVE_LICENSE

4-Warning

No valid license was found. Traffic forwarding has been disabled

A valid license was not found during system initialization. Traffic forwarding will not be enabled until a valid license is installed.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-6-UDI_GENERATED

6-Information

New UDI generated. UDI: [chars]

A new Unique Device Identifier UDI was generated due to the absence of a stored UDI in persistent storage.

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-6-UDI_RETRIEVED

6-Information

Existing UDI retrieved. UDI: [chars]

An existing Unique Device Identifier UDI was retrieved from persistent storage.

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-3-PERSISTENT_RETRIEVE_ERROR

3-Error

Error retrieving persistent data needed for licensing.

An error occurred while retrieving data critical to software licensing from persistent storage.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-UDI_RETRIEVE_ERROR

3-Error

Error retrieving UDI. Error code: [dec]

An error occurred while retrieving an existing Unique Device Identifier UDI from persistent storage.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-UDI_STORE_ERROR

3-Error

Error storing UDI. Error code: [dec]

An error occurred while storing a Unique Device Identifier UDI in persistent storage.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-INVALID_UDI_FORMAT

3-Error

Format of UDI retrieved from persistent storage is not correct. UDI: [chars]

The Unique Device Identifier retrieved from persistent storage is not formatted properly. The proper format is <Product ID>:<Serial Number>

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-INVALID_UDI_PID

3-Error

PID in UDI retrieved from persistent storage not valid for image. PID: [chars]

The Product ID in the Unique Device Identifier retrieved from persistent storage is not valid for this image.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-CAP_RETRIEVE_ERROR

3-Error

Error retrieving hardware capabilities data

An error occurred while retrieving hardware capabilities data required for software licensing validation.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-NODELOCK_CREATE_ERROR

3-Error

Error occurred while creating a node lock

An error occurred while attempting to create information needed for node locked licenses.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-NODELOCK_CHECK_ERROR

3-Error

Error occurred while validating the licensing node lock

The node lock signature originally generated for this Cisco 592x installation does not match the signature generated during IOS initialization. Because of this any installed license is considered invalid.

SWR_DDTS_COMPONENT

"This error will occur when files associated with a " "Cisco 5922 installation are copied to another " "device. If this is not the case open a case with " "the Technical Assistance Center via the Internet " TAC_CASE_OPEN " or contact your Cisco technical " "support representative and provide the " "representative with the gathered information."

LICENSE_C5920-3-NODELOCK_CHECK_ERROR_IN_VM

3-Error

Error occurred while validating the licensing node lock in Virtual Machine

The node lock signature originally generated for this Cisco 592x installation does not match the signature generated during IOS initialization. Because of this any installed license will become invalid and new vUDI will get generated

SWR_DDTS_COMPONENT

"In VM This error is due to either vUDI" " or SMBIOS UUID change in cloned VM." "i.e. cloning after Cisco 5922 is installed." "if this is the case we can modify the .vmx file to retain" "the same UUID else need to install another licnese" "with newly generated vUDI. if nothing works then open" "a case with the Technical Assistance Center via" "the Internet TAC_CASE_OPEN or contact your Cisco technical" " support representative and provide the " "representative with the gathered information."

LICENSE_C5920-3-LEGACY_LIC_NOT_SUPPORTED

3-Error

Legacy license file install is not supported when C5922 running within a Virtual Machine

When C5922 is running on Virtual Machine to avoid duplicate licenses the Legacy license file install is not allowed.

SWR_DDTS_COMPONENT

"Enable smart licensing when C5922 running" "in a Virtual Machine"

LICENSE_C5920-3-MODULE_REGISTER_ERROR

3-Error

Error [dec] occurred while registering module.

An error occurred while registering the platform with the IOS licensing infrastructure.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-STORAGE_CREATE_ERROR

3-Error

Error occurred while creating license storage. [chars]

An error occurred while creating storage for licensing information.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-STORAGE_REGISTER_ERROR

3-Error

Error [dec] occurred while registering license storage.

An error occurred while registering the licensing storage location with the IOS licensing infrastructure.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-FEATURE_REGISTER_ERROR

3-Error

Error [dec] occurred while registering a feature.

An error occurred while registering a licensed feature with the IOS licensing infrastructure.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-CSL_INIT_FAILED

3-Error

Error [dec] occurred while attempting to initialize the licensing infrastructure.

An error occurred while attempting to initialize the IOS licensing infrastructure.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-3-PROCESS_INIT_FAILED

3-Error

Error occurred while attempting to create licensing process.

An error occurred while attempting to create a process critical to licensing validation.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-2-INIT_ERROR

2-Critical

Platform licensing initialization failure - licensing disabled.

An error occurred during the initialization of the platform support for licensing. This will prevent licensing support from being enabled and prevent network interfaces from forwarding packets.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-4-HW_CAPABILITIES_INCREASE

4-Warning

Increase in hardware capabilities detected in use license no longer supported.

An increase in the hardware capabilities was detected and has resulted in the deactivation of an in use license. The hardware capabilities increase has occurred since this license was allowed to be activated. One possibility is that an additional CPU was brought online after the license was installed and activated.

SWR_DDTS_COMPONENT

"Take one of the hardware CPUs offline."

LICENSE_C5920-6-HW_CAPABILITIES_DECREASE

6-Information

Decrease in hardware capabilities detected inactive license activated.

An decrease in the hardware capabilities was detected and has resulted in the activation of an installed license that was not is use due to previous hardware capabilities.

SWR_DDTS_COMPONENT

LOG_STD_ACTION

LICENSE_C5920-4-LOAD_THRESHOLD

4-Warning

Traffic load has reached [dec]%% of enforced rate.

The router traffic rate has reached or exceeded the the reported percentage of the rate allowed by the installed license.

SWR_DDTS_COMPONENT

LOG_STD_NO_ACTION

LICENSE_C5920-4-RATE_EXCEEDED

4-Warning

Traffic load has exceeded the enforced rate. Rate is [dec] Mbps [dec]%% of enforced rate

The total traffic load has exceeded the rate allowed by the installed license

SWR_DDTS_COMPONENT

"Install a license with a higher enforced rate."

PLATFORM_INFRA-5-IOS_INTR_OVER_LIMIT

5-Notice

IOS thread disabled interrupt for [dec] msec

IOS thread process disabled interrupt too long

asr1k-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_EVENT

5-Notice

IOS thread interrupt event [dec].

IOS thread process interrupt event

asr1k-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_HISTORY

5-Notice

[[dec]|[dec]] [[dec]:[dec]] [[dec]->[dec]] ra[ l* 0x[hec] l* 0x[hec] ]

IOS thread process interrupt history

asr1k-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_INVALID_LEVEL

5-Notice

IOS thread interrupt level [dec] replaced by [dec]

An invalid IOS thread interrupt level was used

asr1k-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-4-IOS_DOT1Q_WARNING

4-Warning

#if !defined

-

-

-

PLATFORM_INFRA-3-IOS_DOT1Q_MIN_ERR

3-Error

Invalid MTU size. To send 802.1Q [chars] tagged packets configure linux MTU mapped to [chars] as at least [dec]. Ignore if it is a dot1q Native vlan.

IOS DOT1Q WARNING for minimum MTU size

gemboa-platform

LOG_STD_ACTION

QAT15_CRYPTO-3-INIT

3-Error

Qat15 crypto failed to initialize.

Qat15 crypto engine failed to initialize.

-

LOG_STD_ACTION

QAT15_CRYPTO-3-CRYPTO_ENGINE_INIT

3-Error

Qat15 crypto failed to register with crypto engine infrastructure.

Qat15 crypto engine failed to initialize.

-

LOG_STD_ACTION

QAT15_CRYPTO-3-UNSUPPORTED

3-Error

[chars] not unsupported.

An unsupported operation was invoked.

-

LOG_STD_ACTION

QAT15_CRYPTO-1-ALIGN

1-Alert

[chars] Alignment failure on packet buffer: 0x%08x

A software error occurred. The Qat15 driver detected that the buffer is not aligned correctly.

-

LOG_STD_ACTION

QAT15_CRYPTO-1-ERROR

1-Alert

[chars]

An error occured in the application using Qat15 crypto Module.

-

LOG_STD_ACTION

QAT15_CRYPTO-3-RING_FULL

3-Error

Crypto buffer descriptor ring full.

The buffer descriptor ring is full. Request cannot be serviced.

-

LOG_STD_ACTION

QAT15_CRYPTO-3-NO_BUFFER

3-Error

No buffer to service request.

The dynamic buffer pool has depleted. Request cannot be serviced.

-

LOG_STD_ACTION

QAT15_CRYPTO-3-OVER_SUBSCRIBED

3-Error

Cryptographic packet rate temporary exceeded capacity.

The crypto engine cannot handle the volumne of traffic. Request cannot be serviced.

-

LOG_STD_ACTION

QAT15_CRYPTO-0-SELF_TEST_FAILURE

0-Emergency

Encryption self-test failed.

One of the encryption self-tests has failed. The encryption engine is not operable in this state.

-

"If the failure persists contact Cisco to " "obtain a replacement IOS image."

QAT15_CRYPTO-6-SELF_TEST_RESULT

6-Information

Self test info: [chars]

This audit prompt the results of Cryptographical seltftests

-

"This message is for information only. No action is " "required."

CRB_EVENT-3-CRB_RT_ERROR

3-Error

CRB Runtime Exception: [chars]

CRB Runtime Exception

-

LOG_STD_ACTION

CABLE_UTIL-4-DC_INVOKE_ERR

4-Warning

Dynamic Command [chars] invoke failure

There are several scenarios that the error message will be reported. One case is line card boot up mode for different PIC type does not match to pre-configured PIC type. There two modes of the line card : ICMTS&RPHY and Kobal-R can work with DPIC-G1 or DPIC-G2 with different FW. Eg. if the card is pre-configured as RPHY with the command 'card <slot_num>/0 cBR-CCAP-LC-40G r-phy' but a rf-pic card was inserted to the same slot. Or the card is pre-configured as ICMTS with the command 'card <slot_num>/0 cBR-CCAP-LC-40G' but a dpic card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G2 with the command 'card <slot_num>/0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-<ifmod>' but a DPIC-G1 card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G1 with the command 'card <slot_num>/0 CBR-CCAP-LC-G2-R r-phy' but a DPIC-G2 card was inserted to the same slot. Another case is Kobal-R working ifmod mismatch to precfg. Eg. if system reload with card pre-configured as DPIC-G2-10GE 'card <slot_num>/0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-10GE' while .board.conf was saved as DPIC-G2 100GE mode and Kobal boot up before card precfg parsing then this error message will be reported however it can be recovered by CLC auto reloading.

DDTS_COMPONENT

"change the pre-config to another mode" "or replace the pic card"

CBR_PLFM_HA-3-STATESYNC

3-Error

Redundancy state synchronization failure [dec]/[dec] - [chars]

A failure occurred in trying to synchronize CBR platform information

ubr-sw

LOG_STD_ACTION

CBR_PLFM_HA-3-GET_DATA_PTR

3-Error

[chars]: checkpoint get data pointer error

Checkpoint infra get message data pointer failed

ubr-sw

LOG_STD_ACTION

CBR_PLFM_HA-3-CHKPTADDCLIENT

3-Error

Check Point Client [dec] Add Failed - [dec]

Failed to add checkpoint client

ubr-sw

LOG_STD_ACTION

CBR_PLFM_HA-3-STBY_FP_ERR

3-Error

Standby FP failed to reach sso-ready within tolerated wait time

Standby FP failed to reach sso-ready within tolerated wait time

ubr-sw

LOG_STD_ACTION

CBR_PLFM_HA-3-STBY_PLL_NOT_LOCK

3-Error

Standby PLL failed to lock active within tolerated wait time

Standby PLL failed to lock active within tolerated wait time

ubr-sw

LOG_STD_ACTION

CBR_PLFM_HA-6-STATE_CC

6-Information

Lincard [dec] will be reloaded - [chars]

Lincard is not ready for sup-ha

ubr-sw

LOG_STD_NO_ACTION

CBR_PLFM_HA-3-REPL

3-Error

Failed to setup [chars] chasfs reason: [chars]

Failed to create replication manager related chasfs entry which is used to trigger database sync

ubr-sw

LOG_STD_ACTION

CARD_STATE-3-TYPE_MISMATCH

3-Error

Mismatched card type [chars] in slot [dec]. Expected type [chars].

The linecard inserted does not match the currently provisioned card type.

cbr-platform-infra

"Replace wrong board type with currently provisioned " "board type or type 'no card' to allow new card " "type to be discovered."

CARD_STATE-3-CARD_UNSUPPORT

3-Error

Card in slot [dec] with type [chars] is not supported in version [dec].[dec]

The linecard inserted does not supported in currently running software.

cbr-platform-infra

"Replace the unsupported card or upgrade to right " "software."

CARD_STATE-3-UNEXPECTED

3-Error

Unexpected error on slot [dec]: [chars]

An unexpected error has occured while performing a linecard OIR action

cbr-platform-infra

LOG_STD_ACTION

CARD_STATE-4-FORCE_RESET

4-Warning

Reset slot [dec] for reason: [chars]

The SUP forced a linecard to reload for the reason.

cmts-platform-infra

LOG_STD_ACTION

CARD_STATE-4-INCONSISTANT

4-Warning

Gemini version inconsistant: slot [dec] daughter board [dec] version [chars] slot [dec] daughter board [dec] version [chars]

Different Gemini in chassis CBR only supports the same hardware version US modules.

cmts-platform-infra

"Replace the Gemini to let the version " "of the Gemini in two slots be the same."

CARD_STATE-4-LEOBEN_MISMATCH

4-Warning

Leoben version mismatch: slot [dec] version [chars] slot [dec] version [chars]

Different Leoben in chassis CBR only supports the same hardware version US modules.

cbr-platform-infra

"Replace the Leoben to let the version " "of the Leoben in two slots be the same."

BIPC-3-SESSION_INVALID

3-Error

Invalid Session Slot=[dec] Session=0x%08x

An internal software error has occured. The IPC session was incorrectly not deleted when the slot went down.

DDTS_COMPONENT

LOG_STD_ACTION

BIPC-6-SESSION_UP

6-Information

IPCCL Session to [chars][dec] is UP

An internal software debug info to notify IPCCL session to specific slot went up.

DDTS_COMPONENT

"No action is required."

BIPC-6-SESSION_DOWN

6-Information

IPCCL Session to [chars][dec] is DOWN

An internal software debug info to notify IPCCL session to specific slot went down.

DDTS_COMPONENT

"No action is required."

DBMS-2- INITIALIZATION_FAILED

2-Critical

DBLIB initialization failed for [chars]

Initialization of the database library failed.

cmts-platform-infr

LOG_STD_RECUR_ACTION

DBMS-3- MALLOC_FAILED

3-Error

DBLIB malloc failed for [chars] size [dec]

An internal memory allocation has failed.

cmts-platform-infr

LOG_STD_RECUR_ACTION

DBMS-5- CONNECTION_DROP

5-Notice

DBLIB connection from [chars] to [chars] dropped

An internal socket connection has been dropped.

cmts-platform-infr

LOG_STD_RECUR_ACTION

DBMS-3- IPC_ERROR

3-Error

DBLIB ipc failure : [chars]

An internal inter-process communication error has occurred.

cmts-platform-infr

LOG_STD_ACTION

DBMS-3- TDL_ERROR

3-Error

DBLIB TDL error : [chars]

A TDL messaging error has been detected.

cmts-platform-infr

LOG_STD_ACTION

LCHA_INFRA-3-UNEXPECTED

3-Error

[chars]

An unexpected error has occured while performing a linecard HA action

iosxe-iosd-lcha

LOG_STD_LCHA_SUP_ACTION

LCHA_INFRA-4-CUTOVER

4-Warning

Cutover request received from slot [dec]

A cutover interrupt received from a failing linecard

cmts-platform-infra

"Check core files and crashinfo files. Collect tech-support logs. Collect the system log using CLI 'show logging' and LCHA log on SUP using CLI 'show lcha logging level noise'."

LCHA_INFRA-4-FORCE_RESET

4-Warning

Reset slot [dec] for reason: [chars]

The SUP forced a linecard to reload for the given reason.

cmts-platform-infra

LOG_STD_LCHA_SUP_ACTION

LCHA_INFRA-5-SW_RESET

5-Notice

Soft-reset slot [dec] [chars]

The SUP software reset linecard's processes without HW reset it.

cmts-platform-infra

LOG_STD_NO_ACTION

LCHA_INFRA-6-LCHA_INFO

6-Information

[chars]

lcha information for better monitor chassis lcha relates status

-

LOG_STD_NO_ACTION

CABLE_CLC-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

CABLE_CLC-4-LOGGERMSGTOOBIG

4-Warning

Logger message length [dec] bytes exceeds the maximum allowed size

The carrier card attempted to send a large message to the Route Processor

cmts-platform-infra

LOG_STD_ACTION

CABLE_CLC-4-LCLOG_PARSE_ERR

4-Warning

Error parsing logger message: [chars] from subslot [dec]/[dec]

The carrier card passed down a logger message that could not be parsed.

cmts-platform-infra

LOG_STD_ACTION

CABLE_CLC-4-LCLOG_TOOLONG

4-Warning

Message too long from slot [dec]/[dec]: [dec] bytes

The carrier card passed down a logger message that is too long for\n\ the RP to handle.

cmts-platform-infra

LOG_STD_ACTION

CABLE_CLC-5-LOGGER_LC_REMOVED

5-Notice

Carrier Card [dec] removed

The carrier card was removed

cmts-platform-infra

LOG_STD_NO_ACTION

CABLE_CLC-3-CONFIG_MISMATCH

3-Error

Card type mismatch. config: [chars] is not consistent with the working mode in slot [dec]

There are several scenarios that the error message will be reported. Some cases can be recovered by CLC auto reloading. Eg. Kobal-R can work as 10GE or 100GE ifmod for DPIC-G2. If system reload with card pre-configured as DPIC-G2-10GE 'card <slot_num>/0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-10GE' while .board.conf was saved as DPIC-G2 100GE mode and Kobal boot up before card precfg parsing. Some cases need to shut down the lc first then change the configuration or change the pic card Eg. if the card is pre-configured as RPHY with the command 'card <slot_num>/0 cBR-CCAP-LC-40G r-phy' but a rf-pic card was inserted to the same slot. Or the card is pre-configured as ICMTS with the command 'card <slot_num>/0 cBR-CCAP-LC-40G' but a dpic card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G2 with the command 'card <slot_num>/0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-10GE' but a DPIC-G1 card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G1 with the command 'card <slot_num>/0 CBR-CCAP-LC-G2-R r-phy' but a DPIC-G2 card was inserted to the same slot.

cmts-platform-infra

LOG_STD_ACTION

CBRDTI-6-CHG_CLK_REF

6-Information

Clock reference source set to [chars]

The reasons for the change in clock reference. 1Manual mode configuration command for DTI mode

dti

"Check reference source of DTI"

CBRDTI-5-DTISLOT

5-Notice

DTI slot [dec]/[dec]: card role changed to [chars]\n

Change in role of DTI slot

dti

"Check DTI link/cable"

CBR_LIC-6-WAN_CHANNEL_SHUTDOWN

6-Information

[chars] has been shutdown due to deactivated enforcement

Channel shut due to enforcement

cmts-application

"Buy additional licenses. Please report to TAC"

CBR_LIC-6-WAN_CHANNEL_NO_SHUTDOWN

6-Information

[chars] has been restored to no shut

Restored previously shutdown channels to no shut state

cmts-application

"None"

CBR_LIC-6-WAN_LIC_RESTRICTED

6-Information

[chars] [chars] [chars]

License contract violation! License Restricted/Enforced

cmts-application

"Buy additional licenses and report to TAC"

CBR_LIC-3-APPLY_WAN_FAILED

3-Error

Applying upstream license failed

Unable to apply the upstream license

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-6-WAN_LIC_ENFORCED

6-Information

enforce_en:[dec] [chars] is [dec]

License contract violation! Enforced

cmts-application

"Buy consumed additional licenses and report to TAC"

CBR_LIC-6-LIC_SA_OVERAGE

6-Information

[chars]

Smart License Agent enforcement mode changed to overage

cmts-application

"Report to TAC and add sufficient licenses"

CBR_LIC-6-LIC_SA_OUT_OF_COMPLIANCE

6-Information

[chars]

Smart License Agent enforcement mode changed to out of compliance

cmts-application

"Report to TAC and add sufficient licenses"

CBR_LIC-6-LIC_SA_IN_COMPLIANCE

6-Information

[chars]

Smart License Agent enforcement mode changed to Incompliance

cmts-application

"None"

CBR_LIC-6-LIC_SA_DISABLED

6-Information

[chars]

License contract is violated. The device is disabled

cmts-application

"Report to TAC and add sufficient licenses"

CBR_LIC-6-LIC_SA_GRACE_EXPIRED

6-Information

[chars]

Grace Period has expired. License agent moving to garce-expired state

cmts-application

"Restore communication with cisco"

CBR_LIC-6-LIC_SA_EVAL_EXPIRED

6-Information

[chars]

Eval Period has expired. License agent moving to eval-expired state

cmts-application

"Restore communication with cisco and register " " the device"

CBR_LIC-6-LIC_CAPPED_DURATION_TIMER_STARTED

6-Information

License [chars] period has expired. Capped enforcement is active. The router will be deactivated in 90 days

Eval or Grace Period has expired. Capped enforced - Will be deactivated in 90 days

cmts-application

"Restore communication with cisco and add " "entitlements if out of compliance"

CBR_LIC-6-LIC_OOC_DURATION_TIMER_STARTED

6-Information

License OOC timer has started. All entitlements will be Capped Enforced in 270 days. Please add necessary entitlements

OOC duration timer has started. All entitlements will be Capped Enforced in 270 days.

cmts-application

"Add necessary entitlements to stay in compliance"

CBR_LIC-6-LIC_SA_GLOBAL_NOTIFICATION

6-Information

[chars]

A global notification about an event change in the Smart License Agent was received

cmts-application

"None"

CBR_LIC-3-LIC_SA_REGISTER_FAILED

3-Error

[chars]

Smart License Agent registr failed

cmts-application

"Check call-home pki vrf config and the IdToken"

CBR_LIC-3-LIC_SA_MALLOC_FAILED

3-Error

[chars]

Platform malloc for Smart License Agent failed

cmts-application

"Check the mem usage and report to TAC"

CBR_LIC-3-LIC_SA_NULL_FUN_PTR

3-Error

[chars]

Platform getting a null function pointer from Smart License Agent

cmts-application

"Report to TAC"

CBR_LIC-3-CPB_OPEN_FAILED

3-Error

Failed to open CPB data file for reading and/or writing

Unable to open CPB data file

cmts-application

"Please report to TAC"

CBR_LIC-3-CPB_READ_FAILED

3-Error

Reading CPB data file failed

Unable to read CPB data from file

cmts-application

"Please report to TAC"

CBR_LIC-3-CPB_WRITE_FAILED

3-Error

Writing CPB data file failed

Unable to write CPB data to file

cmts-application

"Please report to TAC"

CBR_LIC-3-CPB_SEEK_FAILED

3-Error

Setting file position failed

Unable to set file position for reading and/or writing

cmts-application

"Please report to TAC"

CBR_LIC-4-CPB_LESS_RECORD

4-Warning

In [chars] [dec] UTC CPB samples loss is more than [dec][dec] hours

CPB samples are less than expected.

cmts-application

"If it is not the first month apply CPB feature " "or maintenance window is no more than 5 hours. Please report to TAC"

CBR_LIC-4-CPB_SN_MISMATCH

4-Warning

CPB data will be removed since they are from Chassis: [chars]. Local Chassis is: [chars].

CPB records were saved in other Chassis.

cmts-application

"This is informational message."

CBR_LIC-5-CPB_EVENT_LOG

5-Notice

CPB event: [chars]

Important event for CPB feature.

cmts-application

"This is informational message."

CBR_LIC-6-US_CHANNEL_SHUTDOWN

6-Information

[chars] has been shutdown due to deactivated enforcement

Channel shut due to enforcement

cmts-application

"Buy additional licenses. Please report to TAC"

CBR_LIC-6-US_CHANNEL_NO_SHUTDOWN

6-Information

[chars] has been restored to no shut

Restored previously shutdown channels to no shut state

cmts-application

"None"

CBR_LIC-6-US_LIC_RESTRICTED

6-Information

[chars] [chars] [chars]

License contract violation! License Restricted/Enforced

cmts-application

"Buy additional licenses and report to TAC"

CBR_LIC-3-APPLY_US_FAILED

3-Error

Applying upstream license failed

Unable to apply the upstream license

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-6-US_LIC_ENFORCED

6-Information

enforce_en:[dec] [chars] is [dec]

License contract violation! Enforced

cmts-application

"Buy consumed additional licenses and report to TAC"

CBR_LIC-6-CHANNEL_SHUTDOWN

6-Information

[chars]:[dec] has been shutdown due to deactivated enforcement

Channel shut due to enforcement

cmts-application

"Buy additional licenses. Please report to TAC"

CBR_LIC-6-CHANNEL_NO_SHUTDOWN

6-Information

[chars]:[dec] has been restored to no shut

Restored previously shutdown channels to no shut state

cmts-application

"None"

CBR_LIC-6-DS_LIC_RESTRICTED

6-Information

[chars] [chars]:[dec] [chars]

License contract violation! License Restricted/Enforced

cmts-application

"Buy additional licenses and report to TAC"

CBR_LIC-6-LICENSE_ENFORCE

6-Information

Enforcement mode set to [chars]

License Information has been applied

cmts-application

"No action required"

CBR_LIC-3-APPLY_DS_FAILED

3-Error

Applying downstream license failed

Unable to apply the downstream license

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-6-CHAN_NOSHUTFAIL

6-Information

[chars] channel [dec] no shut is not allowed due to insufficient licenses

Unable to no shut the channel due to insufficient licenses

cmts-application

"Procure more licenses report to TAC"

CBR_LIC-6-OUT_OF_RANGE

6-Information

[chars] is out of range:[dec]

License counters have reached boundary condition

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-3-CSB_FAIL

3-Error

[chars] Failed for [chars]

An attempt to parse a license related CLI failed

cmts-application

"Check the linecard license details and call TAC"

CBR_LIC-6-DS_LIC_ENFORCED

6-Information

enforce_en:[dec] [chars] is [dec]

License contract violation! Enforced

cmts-application

"Buy consumed additional licenses and report to TAC"

CBR_LIC-6-LIC_CAP_LIMIT_BELOW_CONSUMED

6-Information

[chars]

Capped count cannot be set! Consumed count is higher

cmts-application

"Capped count cannot be set! " "Consumed count is higher"

CBR_LIC-6-LIC_CONFIG_LOCKED

6-Information

[chars]

Configuration lock in effect! Please register the cBR and try

cmts-application

"Configuration lock in effect! " "Register the cBR and try"

CBR_LIC-6-LIC_LIMIT_SET_ALREADY

6-Information

[chars]

To change license limits disable license limits first

cmts-application

"License limits cannot be changed " " without disbling license limits first"

CBR_LIC-3-NULL_LICENSE_INFO

3-Error

License DB is NULL!

The license DB is NULL

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-3-NULL_LICENSE_ENTITLEMENT

3-Error

License entitlement DB is NULL!

The DS license DB is NULL

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-6-LIC_CAPPED_DURATION_EXPIRED

6-Information

Capped Enforcement duration expired. Deactivated Enforced

Capped Enforcement duration expired after an Eval or Grace expired

cmts-application

"Restore communication with cisco and add " "entitlements if required"

CBR_LIC-6-LIC_OOC_DURATION_EXPIRED

6-Information

OOC duration expired - Capped Enforced

OOC duration has expired and hence capped enforced

cmts-application

"Add entitlements to stay in compliance"

CBR_LIC-6-LIC_LIMIT_NOT_SUPPORT

6-Information

[chars]

Don't support Capped Enforcement for this license tag

cmts-application

"License limits cannot be changed for this feature"

CBR_LIC-6-LCHA_CHANNEL_SHUTDOWN

6-Information

[chars]

Channel shut due to enforcement

cmts-application

"Buy additional licenses. Please report to TAC"

CBR_LIC-6-LCHA_CHANNEL_NO_SHUTDOWN

6-Information

[chars] has been restored to no shut

Restored previously shutdown channels to no shut state

cmts-application

"None"

CBR_LIC-6-LCHA_LIC_RESTRICTED

6-Information

[chars] [chars]

License contract violation! License Restricted/Enforced

cmts-application

"Buy additional licenses and report to TAC"

CBR_LIC-3-APPLY_LCHA_FAILED

3-Error

Enforcement failed

Unable to enforce

cmts-application

"Please copy traceback infomation and report to TAC"

CBR_LIC-6-LCHA_LIC_ENFORCED

6-Information

enforce_en:[dec] [chars] is [dec]

License contract violation! Enforced

cmts-application

"Buy consumed additional licenses and report to TAC"

DSG-6-LIST_ERR

6-Information

[chars] [dec]

Infomational only

ubr7200

LOG_STD_NO_ACTION

DSG-6-NAME_RESOLVED

6-Information

hostname <[chars]> is resolved as <[inet]>

DNS query for a hostname is successful.

cmts-application

LOG_STD_NO_ACTION

DSG-6-NO_TG

6-Information

tg <[dec]> removal will remove all tg \conf on bundle and mac-domain.

remove global tg is successful.

cmts-application

LOG_STD_NO_ACTION

DSG-5-NAME_CHANGED

5-Notice

hostname <[chars]> is changed from <[inet]> to <[inet]>

IP address of a hostname is changed.

cmts-application

LOG_STD_NO_ACTION

DSG-5-NAME_UNRESOLVED

5-Notice

hostname <[chars]> cannot be resolved

DNS query for a hostname is not successful.

cmts-application

LOG_STD_NO_ACTION

DSG-6-CFR_APPLIED

6-Information

classifier <[chars]> is applied successfully

classifier is applied successfully.

cmts-application

LOG_STD_NO_ACTION

DSG-5-CFR_NOT_APPLIED

5-Notice

classifier <[chars]> cannot be applied because of errors

classifier cannot be applied because of errors.

cmts-application

LOG_STD_NO_ACTION

DSG-6-CFR_UPDATED

6-Information

classifier <[chars]> is updated

classifier is updated

cmts-application

LOG_STD_NO_ACTION

DSG-5-CFR_CONFLICT

5-Notice

classifier <[chars]> is put into conflict state because of errors

classifier is already applied but we cannot update the classifier with changed destination IP address or source IP address because of errors. So we put the classifier into conflict state.

cmts-application

LOG_STD_NO_ACTION

DSG-5-ILLEGAL_MCASTADDR

5-Notice

IP address <[inet]> is not a multicast address or is a reserved multicast address

IP address is not an multicast address or is a reserved multicast address

cmts-application

LOG_STD_NO_ACTION

DSG-5-ILLEGAL_SOURCEADDR

5-Notice

IP address <[inet]> is an illegal source address

IP address is an illegal source address

cmts-application

LOG_STD_NO_ACTION

DSG-5-SSM_SOURCE_ZERO

5-Notice

destination IP address is <[inet]> in SSM range source IP address cannot be zero

dest-ip is in SSM range src-ip cannot be zero

cmts-application

LOG_STD_NO_ACTION

DSG-5-SSM_SOURCE_PREFIX

5-Notice

destination IP address is <[inet]> in SSM range source IP address prefix length must be [dec]

dest-ip is in SSM range src-ip prefix length should match

cmts-application

LOG_STD_NO_ACTION

DSG-5-MAC_ADDR

5-Notice

cfr [dec] and cfr [dec] have the same destination IP address [inet] but different MAC addresses [enet] and [enet]

two cfrs have the same destination IP address but different MAC addresses

cmts-application

LOG_STD_NO_ACTION

DSG-5-SOURCE_LEN

5-Notice

cfr [dec]: source IP address [inet] and source prefix length [dec] don't match

source IP address and source prefix length of the cfr don't match

cmts-application

LOG_STD_NO_ACTION

DSG-5-IDENTICAL_CFR

5-Notice

cfr [dec] and [dec] are identical

two cfrs are identical

cmts-application

LOG_STD_NO_ACTION

DSG-5-SEMAPHORE_ERROR

5-Notice

failed to obtain the DSG semaphore

failed to get the semaphore

cmts-application

LOG_STD_NO_ACTION

DSG-5-CFRRMTUNNEL

5-Notice

cfr [dec] becomes unresolved it will be removed from the tunnel it belongs to

cfr becomes unresolved it will be removed from the tunnel it belongs to

cmts-application

LOG_STD_NO_ACTION

DSG-5-STATICJOINERR

5-Notice

cfr [dec] cannot be enabled because there already has been a non-DSG static join for S [inet] or * [inet] in interface [chars]

cfr cannot be enabled because there already exists a non-DSG static join for the multicast group

cmts-application

LOG_STD_NO_ACTION

DSG-5-DSG_INFO_DB_LOOKUP_FAILURE

5-Notice

Faild to find the entry from the DSG Info DB for [chars] [chars] [chars]

DSG Info DB lookup failure

cmts-application

LOG_STD_DDTS_TAC_DETAILS

DSG-3-DSG_DA_TO_DSID_DUPLICATED

3-Error

DA [enet] to DSID table duplicated when operation [chars] DSID %X on

DSG DA_TO_DSID table in LC should be unique for DA on a interface.

cmts-application

"Issue the show tech-support command to gather data " "that may help identify the nature of the error.\n" "Then reconfigure DSG in the mac domain to refresh " "all DSG configurations in the interface."

DSG-3-DSG_DCD_UPDATE_FAILURE

3-Error

Faild to DCD message on [chars]

DSG DCD update failure

cmts-application

"Check if DSG traffic is blocked on the " "influenced mac domain.\n" "If so contact your Cisco technical support representative for help."

DSG-3-DSG_DIFFERENT_DSG_DSID

3-Error

different dsid [dec] assign to dsg da2dsid entry [dec]

DSG DSID Allocate Err

cmts-application

LOG_STD_DDTS_TAC_DETAILS

DSG-3-DSG_ZERO_DSG_DSID

3-Error

zero dsid found in dsg da2dsid entry for [[chars] [chars] [enet]]

Zero DSG DSID Found

cmts-application

LOG_STD_DDTS_TAC_DETAILS

DSG-3-DSG_DEL_DSID_FAILURE

3-Error

dsg delete dsid failure [[chars]: [chars] [chars] [enet]]

dsg delete dsid failure

cmts-application

LOG_STD_DDTS_TAC_DETAILS

CBR_MCAST-3-SF_RECOVER

3-Error

Sfid [dec] Recover failed on [chars].

An internal software error occurred.

cbr-cmts-apps

LOG_STD_SH_TECH_ACTION

RPHY_DB-3-DB_HOG

3-Error

MSG_TRACEBACK | MSG_PROCESS

-

-

-

RPHY_DB-3-NEST_LOCK

3-Error

MSG_TRACEBACK | MSG_PROCESS

-

-

-

RPHY_DB-3-UNEXPECTED

3-Error

MSG_TRACEBACK | MSG_PROCESS

-

-

-

RPHY_DB-4-DB_STARVE

4-Warning

Waiting [chars] lock of <[chars]> for [dec] ms

The IOSd process was waiting for the DB lock for too long

rphy-infra

LOG_STD_RPHY_DB_SUP_ACTION

CBR_VIDEO-6-LOGICAL_EDGE_DEVICE

6-Information

LED [dec] [chars].

Logical Edge Device Process terminated/restarted

video-cp

"LOG_STD_NO_ACTION"

CBR_VIDEO-3-LED_NO_RESOURCE

3-Error

LED Subsystem Init Failed

Logical Edge Device subsystem init failed

video-cp

"Verify system memory and check is the image correct."

VIDEO-3-RF_POSTCONFIG_TIMEOUT

3-Error

missing one or more client's RF_POSTCONFIG

Missing RF_POSTCONFIG done from at least one client

cbr-video-cp

"Check if any client has crashed"

VIDEO-3-RF_STBY_BULK_SYNC_TIMEOUT

3-Error

Video standby-bulk-sync timed out

Missing RF_BULK_SYNC done from at least one client

cbr-video-cp

"Check if any client is hang or crashed"

RMFD-3-ERR_LOG

3-Error

[chars]

RMFD Error has occured

cbr-cmts-infra

LOG_STD_NO_ACTION

RMFD-4-WARN_LOG

4-Warning

[chars]

Relay warning message

cbr-cmts-infra

LOG_STD_NO_ACTION

RMFD-5-NOTICE_LOG

5-Notice

[chars]

Relay notice message

cbr-cmts-infra

LOG_STD_NO_ACTION

INFRA_STATS-3-OUT_OF_RANGE

3-Error

[chars] [dec] out of max size [dec] STATS work improperly

Data invalid from DMA

cmts-application

LOG_STD_RECUR_ACTION

INFRA_STATS-3-OUT_OF_SHMEM

3-Error

out of max size [dec] start %p curloc %p type [dec] len [dec] next %lld

Data invalid from NONDMA

cmts-application

LOG_STD_RECUR_ACTION

INFRA_STATS-4-PROCESS_OVERTIME

4-Warning

NON_DMA has been processing for [dec]ms check if CPU high

Process NONDMA Stats overtime it is probably related to CPU high utilization. It is normal to see a small amount of it right after LCHA with scale modems due to low priority of this process and high CPU

cmts-application

LOG_STD_RECUR_ACTION

CMTS_INFRA_LCHA-3-SYNC_CONFIG_LIST_INVALID

3-Error

DOCSIS SYNC configuration list is invalid current slot [dec] virtual slot [dec]

The list of LCHA DOCSIS SYNC configuration is invalid

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA_LCHA-3-SYNC_CONFIG_LIST_CREATION_FAILURE

3-Error

DOCSIS SYNC configuration list creation failure current slot [dec]

Failed to create the list of LCHA DOCSIS SYNC configuration

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA_LCHA-4-RECONCIL_DMP_MISMATCH

4-Warning

LCHA CDMAN to LC DMP Reconciliation: HW-Flow: [dec] Reason: [chars]

Mis-match between CDMAN and LC DMP data

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA_LCHA-4-RECONCIL_UMP_MISMATCH

4-Warning

LCHA CDMAN to LC UMP Reconciliation: Service-Flow: [dec] Reason: [chars]

Mis-match between CDMAN and LC UMP data

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA_LCHA-4-RECONCIL_CM_CDM_MISMATCH

4-Warning

LCHA CDMAN to LC CM Reconciliation: Mac: [enet] Reason: [chars]

Mis-match between CDMAN and LC CM data

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA_LCHA-3-DMP_MCAST_STATUS_TBL_NULL

3-Error

Error:mcast_flow_status_tbl is NULL!

mcast_flow_status_tbl not initialized

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-PNM_ZERO_FREQ_SPAN_CFG

3-Error

PNM: Capture tests cannot be started on port [dec]/[dec]/[dec] dev [dec] - both capture config center frequency: [dec]Hz and span: [dec]Hz should be non zero or no meaningful data can be captured by CLC.

PNM Capture center frequency and span cannot be zero to run captures

cbr-cmts-infra

"Set non zero valid values for capture configuration " "center frequency and span paramters to run captures."

CMTS_INFRA-3-PNM_INVALID_FREQ_SPAN_CFG

3-Error

PNM: Capture tests cannot be started on port [dec]/[dec]/[dec] dev [dec] - Current capcfg freq: [dec]Hz span: [dec]Hz. For this user configured center freq [dec]Hz expected span value should not be more than [dec]Hz.

PNM capture configuration has invalid values capture start rejected

cbr-cmts-infra

"Set the capture configuration center frequency " "and/or span to valid range as per suggested recommendations in msg to" " run captures."

CMTS_INFRA-3-NORES

3-Error

[chars] [dec] [dec]

An internal software error occurred.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-NORES_BG_EXCD

3-Error

[chars] [dec] [dec]

An internal software error occurred.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-DBG_BG_INTF_PER_CTRL_EXCD

3-Error

WB interface resource on [dec]/[dec]/[dec] Exhausted

Unable to allocate additional WB Interface.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-6-DELETE_HW_FLOW_MAC_MISMATCH

6-Information

[chars] [dec] [enet]:[enet]

An internal software error occurred.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-REALLOC_VALID_FLOW

3-Error

Attempt to realloc valid flow: [dec] [enet] md[dec] sid[dec] sfid[dec] dsid[dec]. req: [enet]

An internal software error occurred.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-FPM_ERR

3-Error

[chars]: CM [enet] profile [dec]

A service flow for the modem has been mapped to a profile that is not configured for the ofdm channel.

cbr-cmts-infra

"Remove or correct the ofdm-flow-to-profile " "configuration for the modem."

CMTS_INFRA-3-RELOAD

3-Error

Configuration changed for Gemini 1 ports on card in slot [dec]. Please reload the card for the changes to take effect and save the configuration.

OFDMA channel bandwidth is too small to support the minimum number of mini-slots or no minislot to schedule IR/FR

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-6-CTRLR_CHAN_CONFIG_CONTINUOUS_CHANGE

6-Information

[chars] channel [dec]/0/[dec]:[dec] configuration is being continuously changed or it's admin state is being continuously toggled causing the system to enter an indeterminate state recommend pacing controller/channel config changes.

Controller/channel config is being continuously changed or it's admin state is being toggled this can put the system in an indeterminate state causing the modems to fall offline online or not come online.

cbr-cmts-infra

"Pace controller/channel configuration changes giving the system enough time to react to these events recommeded wait time is 30 seconds between config operations on controllers/channels use the recommendation to toggle channel admin state if modems don't come online or are partially online."

CMTS_INFRA-6-CTRLR_PORT_ADMIN_STATE_LOCKED

6-Information

User attempted to perform a no shut on Integrated-Cable [dec]/0/[dec] [dec] seconds after a shut event. This does not allow resources sufficient time to clean up. Calculated wait time was [dec] seconds between shut/no shut config operations on this controller.

Controller is attempting to be no shut too soon after a shut event. This oepration was blocked to prevent resources from being reused before they have been cleaned up.

cbr-cmts-infra

-

CMTS_INFRA-5-DMP_INVAL_IDX

5-Notice

Invalid Index: [dec] >= [dec]

An internal software error occurred and an Invalid Index value was used. Such errors typically happen due to timing issues and can be ignored if only seen infrequently. Report the error to Tech Support if seen repeatedly.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-NORAND64

3-Error

Failed to read entropy from CPU

Failure to retrieve entropy for random number generator.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-NOTAMC

3-Error

Failed to read entropy from ACT2 for [chars] err: 0x[hec]

Failure to retrieve entropy for random number generator.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-NORANDNIST

3-Error

Failed to generate random number

Failure to generate random number.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

CMTS_INFRA-3-NOENTROPY_PROC

3-Error

Failed to create process to create entropy

CLC doesn't receive HW entropy from RP for the last 10 minutes.

cbr-cmts-infra

LOG_STD_SH_TECH_ACTION

LCPR_INFRA-3-UNEXPECTED

3-Error

[chars]

An unexpected error has occured while performing linecard IOSD or CDMAN process restart.

iosxe-iosd-lcpr

"Check the IPC status of the platform. Collect the system log using CLI 'show logging' and LCHA log on SUP using CLI 'show lcha logging level noise'. Collect the lchaman iosd-clc and cdman btrace logs."

LCPR_INFRA-5-PROGRESSION

5-Notice

[chars]

LCPR generic progression information.

iosxe-iosd-lcpr

LOG_STD_NO_ACTION

VCMS-4-VCMS_CONNECTION

4-Warning

Client connection received for a Linecard [dec]-[dec] already connected

This linecard is already connected to another VCMS simulator

cmts-tools

" Disconnect the first Simulator before attempting" " a new connection"

VCMS-4-VCMS_CONNECTION_LOSS

4-Warning

Connection to simulator lost clearing interfaces for Slot [dec]-[dec]

The VCMS simulator has disconnected from the CMTS

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_INTERFACE_NOT_READY

4-Warning

Interface not ready

The VCMS simulator is trying to bring modems on an interface that is not up or ready.

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_LC_INBAND_CONNECTION

4-Warning

Linecard already connected via Inband Channel

The VCMS simulator is already connected to a linecard via Toaster Inband channel.

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_LC_FWD_AGT_CONNECTION

4-Warning

Linecard already connected to fwd agent

The VCMS simulator is already connected to a linecard via forwarding agent.

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-5-VCMS_CONNECTION_INIT

5-Notice

Simulator version [dec].[dec] from [inet] port [dec] interacting with interface [dec]

The VCMS simulator has started interacting with this interface

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-4-VCMS_INVALID_SIZE

4-Warning

Invalid message size received from the simulator

The simulator sent a message with longer than expected packet size

cmts-tools

"Check the simulator code for possible issues"

VCMS-4-VCMS_INVALID_INTERFACE

4-Warning

Invalid interface Id received from the simulator

The simulator sent a message with interface ID

cmts-tools

"Check the simulator code for possible issues"

VCMS-4-VCMS_INVALID_US_CHAN_ID

4-Warning

Invalid US channel id received from the simulator

The simulator sent a message with invalid US channel id

cmts-tools

"Check the simulator code for possible issues"

VCMS-4-CPE_RECORD_FAIL

4-Warning

Creation of CPE record failed

The proxy was unable to create CPE record due to possible memory failure

-

-

VCMS-5-VCMS_MAJOR_VER_MISMATCH

5-Notice

Error:VCMS connection attempt from client with major version [dec] but expected [dec]

The VCMS simulator major version mismatch

cmts-tools

"LOG_STD_NO_ACTION"

VCMS-5-VCMS_MINOR_VER_MISMATCH

5-Notice

Warning:VCMS connection attempt from client with minor version [dec] but expected [dec]

The VCMS simulator mminor version mismatch

cmts-tools

"Check CMTS memory failures"

VCMS-4-MODEM_RECORD_FAIL

4-Warning

Creation of Modem record failed

The proxy was unable to create Modem record due to possible memory failure

cmts-tools

"Check CMTS memory failures"

VCMS-4-PAKPOOL_FAIL

4-Warning

Packet pool full

The VCMS pakpool was unable to allocate a packet

cmts-tools

"Check Proxy memory leaks"

VCMS-4-PAKPOOL_BUF_ERR

4-Warning

Bad buffer length: [dec]

The VCMS pakpool buffer was insufficient in size

cmts-tools

"Create a DTTS to report/investigate issue."

LCHA-3-CFR_LIST

3-Error

Remove an element before destroy [chars]: cfrid=[dec] direction=[dec] state=[dec] ip_sadd=[inet] ip_daddr=[inet] dest_macaddr=[enet] src_macaddr=[enet] ip_prot=[dec] eport=[dec]

Remove an element from interdb cfr_list before destroy the list.

iosxe-iosd-lcha

"Reset the system"

LCHA-4-DYN_SRV

4-Warning

CM [enet] [chars] transcation id [dec] is not end before lc switch

Dynamic service not finished

iosxe-iosd-lcha

LOG_STD_NO_ACTION

LCHA-4-RF_RESIL_IDX_OUT_OF_RANGE

4-Warning

CM [enet] RF channel id [dec] is out of range [dec]

RF channel index out of range

iosxe-iosd-lcha

LOG_STD_NO_ACTION

UBRCCE-6-US_SFID_INCONSISTENCY

6-Information

US-SF found: SFID [dec] type [dec] sid [dec][dec] MAC [enet][enet] prim_sid [dec][dec]

The RP and LC have different upstream service-flows for the same SFID. The problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBRCCE-6-CM_INCONSISTENCY

6-Information

CM state inconsistency [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received INIT_CM for an online CM Copy the message and report to your technical support representative

ubrcce-sw

LOG_STD_ACTION

UBRCCE-6-STDBY_CM_INCONSISTENCY

6-Information

CM sync received [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received sync message on secondary SUP for mismatched entry This problem should resolve by itself. If it persists report to your technical support representative

ubrcce-sw

LOG_STD_ACTION

UBRCCE-6-HA_CM_INCONSISTENCY

6-Information

CM sync received [enet]msgp [enet] sid [dec] [dec] mac state [dec] hwidb [chars]

Received sync message on secondary SUP for mismatched entry This problem should resolve by itself. If it persists report to your technical support representative

ubrcce-sw

LOG_STD_ACTION

UBRCCE-6-DSD_SRV_FLOW_ERROR

6-Information

SFID found: SFID [dec] type [dec] MAC [enet][enet] prim_sid [dec][dec]

The RP and LC have different service-flows for the same SFID. The problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBRCCE-6-DS_SFID_INCONSISTENCY

6-Information

DS-SF found: SFID [dec] type [dec] MAC [enet][enet] prim_sid [dec][dec]

The RP and LC have different downstream service-flows for the same SFID. The problem should resolve by itself. If it persists report to your technical support representative

ubr10k-sw

LOG_STD_ACTION

UBRCCE-0-CLI_CONFIG

0-Emergency

CMTS[dec]/[dec]/[dec] schrp_cli_cmd failed in [chars]

Most likely S/W failure

ubrcce-sw

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBRCCE-6-RCC_WB_INCONSISTENCY

6-Information

[chars] RCC-[dec] [chars] mismatch with DSBG-[dec] [chars]

Receive chanel set in RCC is mismatch with the Wideband.

ubrcce-sw

LOG_STD_ACTION

UBR7200-2-NOMEMORY

2-Critical

Failure to create new IPv6 entry %P

Unable to malloc a buffer to create a new entry to add Ipv6 addr

cmts-platform

"Enter a show chunks command and report the output along with this " "error message to your technical support representative."

UBR7200-3-INTERCEPT

3-Error

Interface [chars] Failed to send intercept packet to server [inet]:[dec]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-IPV6ADDRERR

3-Error

Host with invalid IPv6 address. Primary Interface [chars] Input Interface [chars] MAC = [enet] IP = %P

Most likely a sw error of the packet sender

ubr7200

"Check the modem and subscriber"

UBR7200-3-IPV4ADDRERR

3-Error

Host with invalid IPv4 address. Primary Interface [chars] Input Interface [chars] MAC = [enet] IP = [inet]

Most likely a sw error of the packet sender

ubr7200

"Check the modem and subscriber"

UBR7200-3-MACADDRERR

3-Error

Upstream packet from host with non unicast MAC address. Primary Interface [chars] Input Interface [chars] SID = [dec] MAC = [enet]

Most likely a sw error of the packet sender

ubr7200

"Check the modem and subscriber"

UBR7200-3-MONITOR_ACCESS_FILTER

3-Error

Null access list

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-MONITOR_EMPTY

3-Error

Unable to allocate packet with rx_type = [dec]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-MONITOR

3-Error

Interface [chars] Failed to send monitored packets

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-0-CPUCARD

0-Emergency

CMTS[dec]/[dec] Init failed CSR[dec]=0x%04x.

Most likely Hardware failure

ubr7200

"Replace defective Line Card"

UBR7200-4-RECALLED_NPE

4-Warning

Old version NPE-175/225 with Rev = 0x%02x system controller. Contact upgrades-info@cisco.com for replacement

NPE board has been recalled due to an errata in the system controller chip.

ubr7200

"Replace NPE-175/225 Board"

UBR7200-1-DISCOVER

1-Alert

Only found [dec] interfaces on bay [dec] shutting down bay

Most likely system or hardware failure

ubr7200

"Replace Line Card"

UBR7200-3-NOTCMTS

3-Error

Device reported [hex]

Most likely hardware failure

ubr7200

"Replace defective hardware"

UBR7200-3-OWNERR

3-Error

CMTS[dec]/[dec] Buffer ownership error pak=0x[hec].

Most likely hardware failure

ubr7200

"Replace defective board"

UBR7200-3-SPIERRW_CHID

3-Error

Invalid Channel ID[chars]: chid=0x%02x cmd=0x%02x regaddr=0x%02x

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-NEG_PENDING

3-Error

Negative decrement of pending stats on [chars] for [enet]

An internal software error occurred.

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-3-SPIERRW

3-Error

SPI PENDING WRITE ERROR[chars]: spistat=0x%02x chid=0x%02x cmd=0x%02x

Write error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-SPIERRR

3-Error

SPI PENDING READ ERROR[chars]: spistat=0x%02x chid=0x%02x cmd=0x%02x

Read error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-SPIERRNRD

3-Error

SPI PENDING NO READ DATA[chars]: spistat=0x%02x chid=0x%02x cmd=0x%02x

Read error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-SPIERRRBS

3-Error

SPI BUS READ 0x%02x BYTES SHORT[chars]: spistat=0x%02x chid=0x%02x

Read error on PHY chip serial communications bus.

ubr7200

"Line card is defective replace it."

UBR7200-3-DBPLX9080ERR

3-Error

Plx9080 id read 0x[hec]expect 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBPLX9050ERR

3-Error

Plx9050 id read 0x[hec]expect 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBFPGAERR

3-Error

XILINX not up reset reg is 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-5-DBDSPUP

5-Notice

Handshake DSP is successful after [dec] ms delay

DSP is up and running

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPERR1

3-Error

DSP SRAM failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR2

3-Error

DSP SRAM semaphore failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR3

3-Error

DSP side dual-port SRAM failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR4

3-Error

DSP FLASH memory failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR5

3-Error

DSP failed to respond to Host Handshake

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPIDERR

3-Error

DSP id read 0x[hec]expect 0x[hec]

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-5-DBDSPRECOVER1

5-Notice

Trying to switch to backup dsp image

Trying to recover DSP using backup image

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-DBDSPRECOVER2

5-Notice

Switching to backup dsp image succeeded

Switching to backup dsp image succeeded

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-DBDSPRECOVER3

5-Notice

Recovering and switching back to regular dsp image succeeded

DSP recover operation using backup image succeeded

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPERR6

3-Error

Switching to backup dsp image failed

Daughter board hardware failure

ubr7200

"Replace defective daughter board"

UBR7200-3-DBDSPERR7

3-Error

Switching again to regular dsp image failed

Daughter board regular image corruption failure

ubr7200

"Replace with BACKUP image"

UBR7200-6-DBDSPVERSION

6-Information

Current DSP version : [dec] DSP flash version : [dec]

The current code version and the version DSP booted up with

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-DBDSPDOWNLOADSTART

6-Information

Downloading dsp code initiated

Downloading dsp code started

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-DBDSPDOWNLOADDONE

6-Information

Downloading dsp code completed

Downloading dsp code completed

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDOWNLOADERR1

3-Error

DSP FAILED TO RESPOND TO INIT_DOWNLOAD CMD.

Failed initiating DSP downloading

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBDSPDOWNLOADPASS1

3-Error

INIT DOWNLOAD OF DSP F/W PASS.

The DSP firmware download initiation was successful

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDOWNLOADPASS2

3-Error

DOWNLOAD OF DSP F/W SUCCESS.

The DSP firmware download was successful

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDOWNLOADERR2

3-Error

Failed downloading.

Failed DSP downloading

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBDSPDOWNLOADERR3

3-Error

FAILED DOWNLOADING OF DSP FW DUE TO CHECKSUM FAILURE.

Failed last step of DSP downloading

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBDSPDOWNLOADPASS3

3-Error

END DOWNLOAD OF DSP F/W SUCCESS.

The DSP firmware end download was successful

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DBDSPDEAD

3-Error

AWACS Slot [dec] is dead

Daughter board DSP hungs

ubr7200

"Reload image if still fail replace defective daughter board"

UBR7200-3-DBFPGADLERR

3-Error

[chars]

XILINX FPGA download failure

ubr7200

"Reload image if still fail replace defective line card"

UBR7200-5-USJIB3NBC

5-Notice

Interface [chars] U[dec] INFO: receives collision no burst

A collision happens on an upstream channel

ubr7200

"If consistently offending modems/channel can be found by" "test cable jib3us show intr-logs 1 on LC console" "and show cable modem on the interface"

UBR7200-5-USIPLCHG

5-Notice

[chars] input power level changed to [dec] dBmV

The upstream channel input power level was changed.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USIPLINVALID

5-Notice

Interface [chars] U[dec] input power level is outside of valid range due to channel width change

The upstream channel input power level is invalid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USCWCHG

5-Notice

[chars] channel width changed to [dec] kHz

The upstream channel width was changed.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-EAEREJECT

5-Notice

EAE registration rejected CM [enet] on Interface [chars]

CM registration rejected to force EAE policy.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USFREQCHG

5-Notice

Interface [chars] U[chars] changed to Freq [dec].%03u MHz

The upstream channel frequency was changed.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USCONTHOP

5-Notice

Interface [chars] U[dec] frequency hop started

All modems just went offline. This message logs the start of frequency hop.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USCONTEND

5-Notice

Interface [chars] U[dec] frequency hop ended at [dec].%03u MHz

At least one modem came back online. This message logs the abort of frequency hop.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USMODCHANGE_WARN

5-Notice

Interface [chars] U[dec] new profile [dec] is [chars] than old profile [dec]

Print warning message about the increase or decrease in through-put

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USMODCHANGE

5-Notice

[chars] dynamic modulation changed to [chars]

Dynamic modulation change from QAM to QPSK and vice-versa.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BADUSPORT

3-Error

Interface [chars] U[dec] invalid highest port number is U[dec]

Upstream port number must be valid.

ubr7200

"Redo command with valid upstream port number."

UBR7200-5-UPDOWN

5-Notice

Interface [chars] U[chars] changed state to [chars]

The upstream port was brought up or down.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-TIMESCH

5-Notice

Time scheduled event spectrum group [dec] [chars]

A time scheduled reconfiguration event occurred on an interface.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-USIPLFIX

5-Notice

Interface [chars] U[dec] input power level fixed at [dec] dBmV

Setting the upstream frequency to a fixed value caused the upstream input power level to assume a fixed value.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BADFFTINTERRUPT

3-Error

BCM3138 chip [dec] dma interrupt error.

FFT dma interrupt error occured.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BADFFTSTATE

3-Error

BCM3138 chip [dec] is in wrong state [dec] expected state [dec]

Impossible state has been reached.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-WRONG3138CHIP

3-Error

BCM3138 current chip [dec] desired chip [dec]

Wrong BCM3138 chip has been selected.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-HUNGFFTSTATE

3-Error

BCM3138 chip [dec] is not idle for [dec] retries

BCM3138 FFT processor stuck

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SPECMGMTGRP

4-Warning

Spectrum group [dec] with discrete frequency is not fully supported on interface [chars]

The spectrum management group is not fully supported

ubr7200

"Suggest convert discrete frequency to frequency band in the group"

UBR7200-3-BADARPDELETE

3-Error

Tried to remove arp entry for [inet] that is not dynamic

Tried to delete non-dynamic arp entry - possible spoof attempt

ubr7200

"Look for possible CMTS IP address spoofing attempt"

UBR7200-5-CLEAR_ARP_TABLE

5-Notice

Clearing all ARP entries

All the entries have been cleared

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-CLEAR_ARP_INTERFACE

5-Notice

Clearing all ARP entries for interface [chars]

All the entries have been cleared

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-BADIPSOURCE

6-Information

Interface [chars] IP packet from invalid source. IP=[inet] MAC=[enet] Expected SID=[dec] Actual SID=[dec]

There might be a spoofing attempt going on.

ubr7200

"Look for possible spoofing attempt"

UBR7200-3-DOCSIS_SYNC_SF

3-Error

cminstp is NULL: [chars].

No valid cminstp is found for sid referenced in this checkpoint msg message will be dropped

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-SUBDB_FREE_IN_ISR

3-Error

Unexpected freeing Subscriber Data in interrupt context host_mac [enet] hwidb [chars]

Unexpected freeing CMTS Subscriber DB data in interrupt context

ubr7200

"Contact TAC support and report the error message."

UBR7200-3-SUBDB_CPE_NO_CM

3-Error

CM doesn't exist when CPE is online on corresponding SID [chars] mac [enet] sid [dec] hwidb [chars]

CM doesn't exist when CPE is online on corresponding SID

ubr7200

"Contact TAC support and report the error message."

UBR7200-3-SUBDB_INIT_FAILURE

3-Error

CMTS Subscriber DB initialization failed [chars] [chars] [chars]

CMTS Subscriber DB initialization failed

ubr7200

"Contact TAC support and report the error message."

UBR7200-4-DHCP_ACK_MISMATCH_CM

4-Warning

Not update cm state for DHCP ACK Expected CM [enet] ip [inet] found CM [enet] ip [inet] new ip [inet]

Found a wrong CM during update DHCP ACK

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DHCP_PAK_TOO_SHORT

4-Warning

DHCP packet is too short from [inet] to [inet] UDP length [dec]

A DHCP packet which is too short was received

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-STALE_IPV4_DB_FOUND

4-Warning

When update IPv4 DB entry for [enet] to ip [inet] tableid [dec] Found stale entry for [inet] tableid [dec] is cm [dec] mac [enet]

Subscriber IPv4 DB entry for CM have not been cleaned

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SUBDB_CLEANUP_CM

4-Warning

Free all Subscriber DB entries for CM [enet] hwidb [chars] ip [inet] tableid [dec] prim sid [dec] sidp %p

Subscriber DB entries for CM have not been cleaned previously clean them now.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-SPOOFEDIP

3-Error

Rejecting IP=[inet] [chars] sid [dec]: Address configured on [chars]

CMTS glean function received overlapping ip address info

ubr7200

"Check for spoofing: CPE may be using CMTS IP addr"

UBR7200-3-SPOOFEDMAC

3-Error

Investigating MAC=[enet] [chars] sid [dec]: Original MAC on sid [dec] [chars]

CMTS glean function received overlapping mac address info

ubr7200

"Check for spoofing: CPE may be reusing mac addr"

UBR7200-6-HOTLISTMAC

6-Information

Investigating MAC=[enet] sid [dec] interface [chars]: MAC blocked

CMTS glean function received blocked mac addr

ubr7200

"Check for spoofing: CPE using blocked mac addr"

UBR7200-3-BPI_ENFORCE

3-Error

Blocking CPE=[enet] CM=[enet] sid [dec] interface [chars]: CPE blocked

CMTS glean function received blocked cpe mac addr

ubr7200

"Check for bpi-plus-policy: CPE blocked mac addr"

UBR7200-4-OVERLAP_IPV4

4-Warning

MAC [enet] on interface [chars] SID [dec] attempting to use [inet]. This address is already in use by MAC [enet] on interface [chars] SID [dec]

There might be an IPv4 spoofing attempt going on.

ubr7200

"Look for possible spoofing attempt"

UBR7200-4-OVERLAP_IPV6

4-Warning

MAC [enet] on interface [chars] SID [dec] attempting to use %P. This address is already in use by MAC [enet] on interface [chars] SID [dec]

There might be an IPv6 spoofing attempt going on.

ubr7200

"Look for possible spoofing attempt"

UBR7200-4-NOTLEARNABLE

4-Warning

New address of CPE [enet] behind modem [enet] on interface [chars] is ignored: [chars]. Count [dec]

The CPE is not learnable due to provisioning.

ubr7200

"Provisioning failure. Please check configuration"

UBR7200-5-MAXHOST

5-Notice

Interface [chars] New host with MAC [enet] on SID [dec] CM [enet] is ignored: [chars]. Count [dec]

-

-

-

UBR7200-3-ZOMBIESID

3-Error

SID [dec] macaddr [enet] us_channel_id [dec] rng_list_id [dec] ds_time_stamp %llu rngpoll_timeout %llu now %lu last_ranging %lu stn_mtn=[dec] cont_mtn=[dec] pending=[dec].

SID instance didn't get cleanup after modem is gone.

ubr7200

"Call TAC and show him/her the log."

UBR7200-4-NOCPUVER

4-Warning

Invalid CPU ID assuming revision 1

CPU Revision ID is unreadable.

ubr7200

"Update CPU board."

UBR7200-3-CONFIG

3-Error

Exceeds [dec] [chars]

The total bandwidth of fast and medium bandwidth port adapters exceed the rated capacity of this system.

ubr7200

"Refer to the configuration guidelines for the maximum allowed " "high and medium bandwidth port adapters for the system."

UBR7200-4-VERSION_MISMATCH

4-Warning

Midplane data version mismatch.

Data stored in midplane is out of date and needs update.

ubr7200

"Contact technical support to update your system."

UBR7200-4-MACBLKSIZE

4-Warning

Unknown MAC address block size.

Data stored in midplane is bad or incomplete.

ubr7200

"Contact technical support to update your system."

UBR7200-3-CHASSIS

3-Error

Unknown chassis model.

Data stored in midplane is bad or incomplete.

ubr7200

"Contact technical support to update your system."

UBR7200-3-SLOTS

3-Error

Number of slots in chassis is undefined.

Data stored in midplane is bad or incomplete.

ubr7200

"Contact technical support to update your system."

UBR7200-3-NOMAC

3-Error

Can't allocate MAC address for interface [dec]/[dec]

Your system is out of available MAC addresses.

ubr7200

"Contact technical support."

UBR7200-4-COOKIE

4-Warning

Corrupt or missing MAC address cookie\n using random base [enet]

Data stored in midplane is bad.

ubr7200

"Contact technical support to update your system."

UBR7200-0-VOLTLOW

0-Emergency

[chars] measured at [chars] is too low: shutdown voltage [chars]

Current voltage exceeds the min shutdown voltage

ubr7200

"Determine cause of the low voltage and correct if possible."

UBR7200-0-VOLTHIGH

0-Emergency

[chars] measured at [chars] is too high: shutdown voltage [chars]

Current voltage exceeds the max shutdown voltage

ubr7200

"Determine cause of the high voltage and correct if possible."

UBR7200-0-TEMPHIGH

0-Emergency

[chars] measured at [chars] is too high: shutdown temperature [chars]

Current temperature exceeds the max shutdown temperature

ubr7200

"Determine cause of the high temperature and correct if possible."

UBR7200-6-GRDIDX_LOG

6-Information

DS [dec]/[dec]/[dec] Index [dec] DSID 0x[hec] SID [dec] SF_BU [dec] FW [chars] [dec]/[dec]/[dec]:[dec] MD Ca[dec]/[dec]/[dec] [chars] [chars]

Debug message for Guardian index operations

ubr10000

LOG_STD_NO_ACTION

UBR7200-6-MDIDX_LOG

6-Information

GRD [dec]/[dec] Index [dec] SID [dec] SF [dec] FW [chars] [dec]/[dec]/[dec]:[dec] MD [chars] [chars] [chars]

Debug message for MAC Domain index operations

ubr10000

LOG_STD_NO_ACTION

UBR7200-3-IPCRECVERR

3-Error

Internal RP-CLC/CLC-CLC IPC receive error from [dec]/[dec]

Internal IPC receive error\n

ubr10000

LOG_STD_NO_ACTION

UBR7200-6-CREATE_MAUTH_PROF

6-Information

<132>CMTS[DOCSIS]:<89010300> Multicast Profile [chars] created for CM Mac [enet].

CMTS automatically creates an IP Multicast Profile

cbr-application

LOG_STD_NO_ACTION

UBR7200-6-MCAST_SESS_NOT_AUTH

6-Information

<132>CMTS[DOCSIS]:<89010200> Multicast session [chars] is not authorized for CM [enet]

Default configured action for IGMP Join is denied or the matching session rule's action is denied or the maximium session limit for the modem has been reached.

cbr-application

LOG_STD_NO_ACTION

UBR7200-3-IPV6SOCKETFAIL

3-Error

IPv6 TFTP server socket

Could not open the IPv6 TFTP server socket

ubr7200

"Make sure the /"ip tftp-server /" CLI is not configured"

UBR7200-4-NOCFGFILE

4-Warning

Cannot read modem config file [chars] from [inet]: [chars]

Configuration file for the cable modem cannot be read

ubr7200

"Make sure the config file is accesable to the CMTS"

UBR7200-4-BADCFGFILE

4-Warning

Modem config file [chars] at [inet]: [chars]

Configuration file for the cable modem has problems

ubr7200

"Make sure the config file is proper"

UBR7200-4-NOCFGFILE_V6

4-Warning

Cannot read modem config file [chars] from %P: [chars]

Configuration file for the cable modem cannot be read

ubr7200

"Make sure the config file is accesable to the CMTS"

UBR7200-4-BADCFGFILE_V6

4-Warning

Modem config file [chars] at %P: [chars]

Configuration file for the cable modem has problems

ubr7200

"Make sure the config file is proper"

UBR7200-4-TFTP_DATA_LEN_ERROR

4-Warning

The length of TFTP DATA packet exceeded negotiated/default block size of [dec] while downloading [chars] from [inet]

TFTP DATA packet received exceeded its negotiated/default block size

ubr7200

"Make sure that the block size of the TFTP DATA packets" "does not exceed the negotiated/default block size"

UBR7200-4-CMMARKED

4-Warning

Cable Modem [enet] in [chars] attempted theft of service

Configuration file for the cable modem has problems

ubr7200

"Cable modem attempted to steal service"

UBR7200-4-CMLOCKED

4-Warning

Cable Modem [enet] in [chars] locked due to [chars] theft of service

Configuration file for the cable modem has problems

ubr7200

"Cable modem attempted to steal service"

UBR7200-4-OACKERROR

4-Warning

TFTP Option Negotiation Error for [chars] file at [inet]: [chars]

TFTP OACK packet is malformed or wrong options appended

ubr7200

"Make sure TFTP Server supports TFTP Options"

UBR7200-4-OACKERROR_V6

4-Warning

TFTP Option Negotiation Error for [chars] file at %P: [chars]

TFTP OACK packet is malformed or wrong options appended

ubr7200

"Make sure TFTP Server supports TFTP Options"

UBR7200-5-BADMNCSMSG

5-Notice

Invalid DOCSIS Message Type [dec] received from the CM [enet] for interface [chars]

-

-

-

UBR7200-5-UNREGSIDTIMEOUT

5-Notice

CMTS deleted unregistered Cable Modem [enet]

Unregistered cable modem deleted to avoid unaccounted bandwidth usage.

ubr7200

"Check modem i/f config for registration bypass " "or errors in tftp config file."

UBR7200-5-UNAUTHSIDTIMEOUT

5-Notice

CMTS deleted BPI unauthorized Cable Modem [enet]

Unauthorized cable modem deleted to enforce CM go through BPI authorization.

ubr7200

"Check modem interface configuration for privacy mandatory " "or errors in tftp configuration file."

UBR7200-5-TEKREQTIMEOUT

5-Notice

CMTS deleted BPI Cable Modem [enet] because traffic not encrypted

Cable modem deleted to force modem to request TEK.

ubr7200

"Check upsteam utilization to ensure bandwidth available for TEK " "request. Noise on the plant can cause this also."

UBR7200-5-EXPIREDBPITIMEOUT

5-Notice

CMTS deleted BPI [chars] expired Cable Modem [enet] with Sid [dec]

Expired cable modem deleted to enforce CM go through BPI authorization.

ubr7200

"Check modem interface configuration for privacy mandatory " "or noise on the plant."

UBR7200-5-BPKMDROPEXCESS

5-Notice

CMTS deleted excessive [chars] Requests Cable Modem [enet] with Sid [dec]

Cable Modem did excessive BPKM requests.

ubr7200

"Check modem interface configuration for privacy mandatory " "or noise on the plant."

UBR7200-5-NOMULTIPLEUPSTREAMS

5-Notice

Upstream Channel Change not valid for interface [chars]

The software does not support this command for this interface

ubr7200

"Please use this command on a multiple upstream Line card"

UBR7200-3-RP_INVALIDSID_ASSIGN

3-Error

Invalid SID assignment for interface: [chars] CM: [enet]

Invalid SID assignment by RP

ubr7200

"Contact Cisco TAC"

UBR7200-3-NOMORESIDS

3-Error

Maximum number of SIDS have been allocated for interface [chars]: CM [enet]: SID container info: start [dec] end [dec]

The Maxmium number of SIDS has reached

ubr7200

"Assign Cable Modem to another Line Card"

UBR7200-3-TOOMANY_RANGEDSIDS

3-Error

CMTS-HCCP [chars]: Actual Rcvd ranged list sync sids [dec] # of sids saved [dec]

Size of Ranged List Sync Message received.

ubr7200

"Reduce the Number of Cable Modem Sids pre i/f"

UBR7200-3-SIDERRORHCCP

3-Error

Tried to allocate New SID during Failover for interface [chars]: CM [enet]: SID container info: start [dec] end [dec]

Allocate SID during Failover

ubr7200

"Assign Cable Modem to another Line Card"

UBR7200-4-SIDERRORDCC

4-Warning

Tried to allocate new SID [dec] during DCC CM rebuild for interface [chars]: CM [enet]: SID container info: start [dec] end [dec]

Allocate SID during DCC CM rebuild

cbr-application

"Assign Cable Modem to another interface"

UBR7200-4-CM_NP_RF_FAILURE

4-Warning

CM <[enet]> on host interface <[chars]> reported NP RF <[dec]> failure modular-cable <[chars]> CM's NP RFs <[chars]>

CMTS is configured to run script via Embedded Event Manager to handle the Cable Modem NP RF failure.

cbr-application

"Verify that Cable Modem is not experienceing wideband connectivity."

UBR7200-3-NULLMAPPTR

3-Error

Cannot send maps as current_map ptr is NULL\n ds->[hec]current_map->[hec]: [chars]

This is an internal error or may indicate a memory problem.

ubr7200

"Check your available memory. If necessary " "add more memory to the system."

UBR7200-3-I2CERR

3-Error

[chars]

ERROR while accessing the i2c bus

ubr7200

"Error has occured while accessing the internal bus."

UBR7200-3-I2CUPXERR

3-Error

[chars]

ERROR while accessing the Upconverter

ubr7200

"Error occured while accesing the upconverter."

UBR7200-3-SEMCREATEFAIL

3-Error

Unable to create the semaphore

Unable to create the semaphore for non-blocking UPX access

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-SEMLOCKFAIL

3-Error

Unable to lock the semaphore

Unable to lock the semaphore for non-blocking UPX access

ubr7200

"Unable to read the Upconverter status Try again"

UBR7200-3-NOMEM

3-Error

[chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-6-DUAL_CLEANUP_ATTEMPT

6-Information

Second cleanup for modem

A modem entry was attempted to be cleaned up twice

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-NOFORK

3-Error

Could not start Spectrum Management process

An internal software error occurred.

ubr7200

"LOG_STD_SH_TECH_ACTION"

UBR7200-4-CMTS_IPV6_LLA_FAILED_DAD

4-Warning

<133>CMTS[DOCSIS]:<68001301> IPv6 Link-local address has failed DAD. Addr <[enet]>

IPv6 Link-Local has failed DAD.\n

ubr7200

"Check the modem and subscriber"

UBR7200-4-CMTS_IPV6_RX_DHCPV6_WITH_BADADDR

4-Warning

DHCPv6 request received with a bad src IPv6 \naddr. IP <%P> msg <[chars]>

DHCPv6 request received with a bad src IPv6 addr dropping the req\n

ubr7200

"Check the modem and subscriber"

UBR7200-2-CPE_MGMT_IDX_ERR

2-Critical

Index out of range during CPE MGMT data decoding

\nThe index is out of range during CPE MGMT HCCP data decoding.

ubr7200

"Contact Cisco with this log message"

UBR7200-4-REGISTRATION_BEFORE_TFTP_MARK

4-Warning

Registration request unexpected: Cable Modem did not attempt TFTP. Modem marked with #. CM Mac Addr <[enet]>

Registration request unexpected: Cable Modem did not attempt TFTP\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REGISTRATION_BEFORE_TFTP

4-Warning

Registration request unexpected: Cable Modem did not attempt TFTP. Registration Rejected. CM Mac Addr <[enet]>

Registration request unexpected: Cable Modem did not attempt TFTP\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_DS_SELECTION_FAIL

4-Warning

DS Selection failed for Cable Modem [enet] in [chars]

CMTS cannot proceed with handling modem's Registration Request

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_REGISTRATION

4-Warning

Cable modem [enet] on interface [chars] when [chars] attempted re-registration with different QoS

Modem sent a registration request when already registered with a different QoS

ubr7200

"Modem could be attempting theft of service"

UBR7200-4-MTA_REQ_ON_NON_HA_DS

4-Warning

MTA Modem [enet] in [chars] to come online on a non-HA capable DS

CMTS can not move the MTA to a DS that is HA capable after 3 trials

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-CLASSFAIL

5-Notice

Registration failed for Cable Modem [enet] on interface [chars][chars]: [chars]

The registration of this modem failed due to an invalid or unsupported Class of Service setting.

ubr7200

"Make sure the Class of Service fields in the configuration file " "are set correctly."

UBR7200-5-OVERLIMIT

5-Notice

Interface [chars]\n Current total reservation of [dec] bps on Port U[dec] exceeds its\n maximum configured reservation limit of [dec] bps.\n

The currently reserved capacity on the upstream channel\n already exceeds the virtual reservation capacity of that\n upstream channel based on configured subscription level limit.\n

ubr7200

"Need to load balance modems requesting reserved upstream rate on\n" "some other upstream channel or increase the subscription level\n" "limit on current upstream channel at increasing risk of not being\n" "able to guarantee the individual reserved rates for modems if this\n" "upstream channel is already oversubscribed beyond raw capacity\n"

UBR7200-5-TRAFSHAPNOCREAT

5-Notice

Unable to create downstream traffic shaping queues

A possible memory error has occurred which is preventing the software from creating downstream traffic shapping queues.

ubr7200

"Gather information about running configuration and amount of memory " "in the system and report it to your technical support representative."

UBR7200-5-TRAFSHAPPROCFAIL

5-Notice

Unable to fork downstream shaper process

A possible memory error has occurred which is preventing the software from creating the downstream shaper process.

ubr7200

"Gather information about running configuration and amount of memory " "in the system and report it to your technical support representative."

UBR7200-5-TRAFSHAPBADTIMER

5-Notice

Bad timer expiry in downstream traffic shaper process Timer [hec]

An unknown downstream traffic shaper timer has expired.

ubr7200

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200-6-CMMOVED

6-Information

Cable modem [enet] has been moved from interface [chars] to interface [chars].

The cable modem has been detected ranging on a new interface.

ubr7200

"Informational only"

UBR7200-6-USPRIMARYSFIDCONFLICT

6-Information

Assigned us primary sfid [dec] conflicts with existing us primary sfid [dec] for Cable modem [enet] on interface [chars]

The assigned upstream primary SFID conflicts with the existing upstream primary SFID for the cable modem.

ubr7200

"Informational only"

UBR7200-6-DSPRIMARYSFIDCONFLICT

6-Information

Assigned ds primary sfid [dec] conflicts with existing ds primary sfid [dec] for Cable modem [enet] on interface [chars]

The assigned downstream primary SFID conflicts with the existing downstream primary SFID for the cable modem.

ubr7200

"Informational only"

UBR7200-6-FECKBYTEADJUST

6-Information

[chars] burst's FEC K BYTE in mod profile [dec] is adjusted to [dec] bytes.

The FEC K bytes in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-DIFFENCADJUST

6-Information

Differential-encoding is disabled on interface [chars] upstream [chars] it is only supported for QPSK or QAM16.

Differential-encoding is only supported for QPSK or QAM16.

ubr7200

"Informational only"

UBR7200-6-LCHDIFFENCADJUST

6-Information

Differential-encoding is disabled on interface [chars] upstream [chars] it should be supported by all active logical channels.

Differential-encoding should be supported on all logical channels.

ubr7200

"Informational only"

UBR7200-6-PREAMLENADJUST

6-Information

[chars] burst's preamble length in mod profile [dec] is adjusted to [dec] bits.

The preamble length in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-PREAMLENCHECK

6-Information

preamble length exceeds total of 128 byte.

The preamble length exceeds total of 128 byte.

ubr7200

"Informational only"

UBR7200-6-GUARDSYMLENADJUST

6-Information

[chars] burst's guard symbol length in mod profile [dec] is adjusted to [dec] symbols.

The guard symbol length in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-RSINTRLVBLKSIZEADJUST

6-Information

[chars] burst's RS interleave block size in mod profile [dec] is adjusted to [dec] bytes.

The RS interleave block size in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-RSINTRLVDEPTHADJUST

6-Information

[chars] burst's RS interleave depth in mod profile [dec] is adjusted to [dec].

The RS interleave depth in the burst profile adjusted to a valid value.

ubr7200

"Informational only"

UBR7200-6-RSINTRLVDISABLED

6-Information

[chars] burst's RS interleaver in mod profile [dec] is auto disabled.

The RS interleaver in the burst profile is auto disabled.

ubr7200

"Informational only"

UBR7200-4-DUPLICATEMAC

4-Warning

Cable modem [enet] is online on both interface [chars] and interface [chars].

The cable modem has been detected on two interfaces.

ubr7200

"Check for cable modems with duplicate MAC addresses."

UBR7200-4-SIDWITHOUTCM

4-Warning

SID [dec] not bound to any CM.

This SID does not have a valid CM database pointer

ubr7200

"NO action is required"

UBR7200-4-CMNOPRIMSF

4-Warning

CM [enet] does not have any primary service flows

This CM has no primary service flows

ubr7200

"NO action is required"

UBR7200-6-ACTIVE

6-Information

Cable clock [chars] reference active

The clock reference became active

ubr7200

"Informational only"

UBR7200-6-LOS

6-Information

Cable clock [chars] reference Loss of Signal

The clock reference was lost

ubr7200

"Check reference source"

UBR7200-6-HOLDOVER

6-Information

Cable clock in Holdover mode

Clockcard switched to holdover mode

ubr7200

"Check reference source"

UBR7200-6-FREERUN

6-Information

Cable clock in Freerun mode

Clockcard is in free run mode

ubr7200

"Informational only"

UBR7200-6-REFLOCK

6-Information

Cable clock locked to [chars] reference

Clockcard locked onto clock source

ubr7200

"Informational only"

UBR7200-6-SRCMP

6-Information

Cable Clock primary reference is midplane TDM clock

Clockcard primary reference is from midplane TDM clock

ubr7200

"Informational only"

UBR7200-6-DRVMP

6-Information

Midplane TDM clock reference defaults to Clockcard

Clockcard primary reference is from midplane TDM clock

ubr7200

"Informational only"

UBR7200-4-CLK_HWFAULT

4-Warning

Hardware Fault in Clockcard

Hardware fault in Clockcard

ubr7200

"Replace clock card"

UBR7200-6-BADTXOFFSET

6-Information

Bad timing offset %ld detected for cable modem [enet] sid [hec] cm status [hec] dcc [chars] skip_reg [chars].

The cable modem is not using the correct starting offset during initial ranging. This causes a zero negative timing offset to be recorded by the CMTS for this modem. The CMTS internal algorithms that rely on the

ubr7200

"Locate the cable modem based on MAC address and report initial " "timing offset problem to the CM vendor"

UBR7200-6-MAP_UPSTREAM_BW_ALLOCATION

6-Information

<135>CMTS[DOCSIS]:<77000100> A transmit opportunity was missed because MAP arrived too late

A transmit opportunity was missed because MAP arrived too late \n

ubr7200

"If the problem persists with a particular cable modem " "reboot the cable modem and check for possible hardware or" "software problems with that cable modem If this problem " "occurs with many cable modemscheck the cable plant for " "RF transmission and noise ingress problems."

UBR7200-4-NO_RANGING_REQUESTS

4-Warning

<133>CMTS[DOCSIS]:<82010100> No Ranging Requests received from POLLED CM Mac Addr <[enet]> CMTS generated polls

No Ranging Requests received from POLLED CM CMTS generated polls\n

ubr7200

"Please look for possible noise or other RF plant " "problems on the upstream channel"

UBR7200-4-RETRIES_EXHAUSTED_POLL_CM

4-Warning

<133>CMTS[DOCSIS]:<82010200> Retries exhausted for polled CM Mac Addr <[enet]>. After 16 R101.0 errors.

Retries exhausted for polled CM . After 16 R101.0 errors.Note: this is different from R102.0 in that it was able to try i.e. got REQ's but failed to Range properly.\n

ubr7200

"Please look for possible noise or other RF plant " "problems on the upstream channel"

UBR7200-4-UNABLE_TO_RANGE_CM

4-Warning

<133>CMTS[DOCSIS]:<82010300> Unable to Successfully Range CM Mac Addr <[enet]>. Retries Exhausted.

Unable to Successfully Range CM Retries Exhausted.\n

ubr7200

"CM reinitialize its MAC interface and attempt to reregister." " check the cable plant for potentialnoise or other RF problems" " Check the configuration of the cable interface on the CMTS " " that is servicing this cable modem to ensure that the interface" " is enabled and properly configured"

UBR7200-4-NO_RNG_REQ_TIMEOUT_SID

4-Warning

<133>CMTS[DOCSIS]:<82010400> Failed to receive Periodic RNG-REQ from modem [chars] timing-out SID

Failed to receive Periodic RNG-REQ from modem SID X timing-out SID\n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-SERVICE_UNAVAIL_OTHER

4-Warning

<133>CMTS[DOCSIS]:<73000400> Service unavailable - Other. CM Mac Addr <[enet]>

Registration Failed :Service Unavailable \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73000401> Service unavailable - Unrecognized configuration setting. CM Mac Addr <[enet]>

Registration Failed Unrecognized Configuration Setting\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SERVICE_TEMPORARILY_UNAVAILABLE

4-Warning

<133>CMTS[DOCSIS]:<73000402> Service unavailable - Temporarily unavailable. CM Mac Addr <[enet]>

Registration Failed Service temporarily not available \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-SERVICE_PERMANENTLY_UNAVAILABLE

4-Warning

<133>CMTS[DOCSIS]:<73000403> Service unavailable - Permanent. CM Mac Addr <[enet]>

Service Permanently unavailable\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REJ_AUTH_FAIL_CMTS_MIC_INVALID

4-Warning

<133>CMTS[DOCSIS]:<73000500> Registration rejected authentication failure: CMTS MIC invalid. CM Mac Addr <[enet]>

Registration rejected authentication failure: CMTS MIC invalid\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REJ_AUTH_FAIL_TLV_PARAMS_MISMATCH

4-Warning

<133>CMTS[DOCSIS]:<73000501>Registration authentication failure: REG REQ rejected TLV parameters do not match learned config file TLV parameters. CM Mac Addr <[enet]>

REG REQ TLV parameters do not match learned config fileTLV parameters\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_INVALID_MAC_HEADER

4-Warning

<133>CMTS[DOCSIS]:<73010100> REG REQ has Invalid MAC header. CM Mac Addr <[enet]>

REG REQ has Invalid MAC header \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_SID

4-Warning

<133>CMTS[DOCSIS]:<73010200> REG REQ has Invalid SID or not in use. CM Mac Addr <[enet]>

REG REQ has Invalid SID or not in use\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REQUIRED_TLV_ABSENT

4-Warning

<133>CMTS[DOCSIS]:<73010400> REG REQ missed Required TLV's. CM Mac Addr <[enet]>

REG REQ missed Required TLV's \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DOWNSTREAM_FREQUENCY_FORMAT_INVALID

4-Warning

<133>CMTS[DOCSIS]:<73010500> Bad DS FREQ - Format Invalid. CM Mac Addr <[enet]>

REG REQ : Bad DS FREQ - Format Invalid .\n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DOWNSTREAM_FREQUENCY_NOT_IN_USE

4-Warning

<133>CMTS[DOCSIS]:<73010501> Bad DS FREQ - Not in use. CM Mac Addr <[enet]>

REG REQ : Bad DS FREQ - Not in use.\n

ubr7200

"Please Check the Config File Frequency"

UBR7200-4-DOWNSTREAM_FREQUENCY_NOT_MULTIPLE_OF_62500

4-Warning

<133>CMTS[DOCSIS]:<73010502> Bad DS FREQ - Not multiple of 62500. CM Mac Addr <[enet]>

REG REQ : Bad DS FREQ - Not multiple of 62500.\n

ubr7200

"Please Check the Config File Frequency"

UBR7200-4-INVALID_UNASSIGNED_UPSTREAM_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<73010600> Bad US CH - Invalid or Unassigned. CM Mac Addr <[enet]>

REG REQ : Bad US CH - Invalid or Unassigned.\n

ubr7200

"Please Check the upstream Channel Frequency"

UBR7200-4-UPSTREAM_CHANNEL_CHANGE_WITH_REG_REQ

4-Warning

<133>CMTS[DOCSIS]:<73010601> Bad US CH -Change followed with RE- Registration REQ. CM Mac Addr <[enet]>

REG REQ : Bad US CH -Change followed with RE- Registration REQ .\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_UPSTREAM_CHANNEL_OVERLOAD

4-Warning

<133>CMTS[DOCSIS]:<73010700> Bad US CH -Overload. CM Mac Addr <[enet]>

REG REQ : Bad US CH -Overload.\n

ubr7200

"Check the Upstream Frequency"

UBR7200-4-BAD_NETWORK_ACCESS_CONFIGURATION

4-Warning

<133>CMTS[DOCSIS]:<73010800> Network Access has Invalid Parameter. CM Mac Addr <[enet]>

REG REQ : Network Access has Invalid Parameter.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_COS_CONFIGURATION

4-Warning

<133>CMTS[DOCSIS]:<73010900> Bad Class of Service- Invalid Configuration. CM Mac Addr <[enet]>

Registration Failed Bad Class of Service\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-COS_UNSUPPORTED_CLASS

4-Warning

<133>CMTS[DOCSIS]:<73011000> Bad Class of Service- Unsupported class. CM Mac Addr <[enet]>

Registration Failed Bad Class of Service-Unsupported class\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-COS_INVALID_ID_OUT_OF_RANGE

4-Warning

<133>CMTS[DOCSIS]:<73011100> Bad Class of Service. Invalid Class ID or out of range. CM Mac Addr <[enet]>

Bad Class of Service. Invalid Class ID or out of range.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_MAX_DOWNSTREAM_BIT_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011200> Bad Max DS bit - Invalid format. CM Mac Addr <[enet]>

Registration Failed Bad Max Downstream bit has invalid format.\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_MAX_DOWNSTREAM_BITRATE_UNSUPPORTED_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73011201> Bad Max DS Bit Rate Unsupported Setting. CM Mac Addr <[enet]>

REG REQ : Bad Max DS Bit Rate Unsupported Setting.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_MAX_UPSTREAM_BIT_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011300> Bad Max US Bit - Invalid format. CM Mac Addr <[enet]>

Registration Failed Bad Max Upstream bit Rate has invalid format.\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BAD_MAX_UPSTREAM_BITRATE_UNSUPPORTED_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73011301> Bad Max US Bit Rate - Unsupported Setting. CM Mac Addr <[enet]>

REG REQ : Bad Max US Bit Rate - Unsupported Setting.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_UPSTREAM_PRIORITY_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011400> Bad US Priority Configuration - Invalid format. CM Mac Addr <[enet]>

Registration Failed Upstream Priority Format has invalid format.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OUT_OF_RANGE_US_PRIORITY_CONFIGURATION

4-Warning

<133>CMTS[DOCSIS]:<73011401> Bad US Priority Configuration - Setting out of Range. CM Mac Addr <[enet]>

Out of Range US Traffic Priority Value.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_MIN_UPSTREAM_CHANNEL_BIT_RATE_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011500> Bad Guaranteed MIN US Channel bit Rate Configuration setting - Invalid format. CM Mac Addr <[enet]>

Guaranteed Minimum Upstream Rate format invalid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-MIN_UPSTREAM_CHANNEL_BIT_RATE_EXCEEDS_MAX

4-Warning

<133>CMTS[DOCSIS]:<73011501> Bad Guaranteed Min US Channel Bit Rate Configuration setting - Exceed Max US Bit Rate. CM Mac Addr <[enet]>

CM MIN Upstream Channel Bit Rate exceeds maximum value.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-MIN_UPSTREAM_CHANNEL_BITRATE_OUT_OF_RANGE

4-Warning

<133>CMTS[DOCSIS]:<73011502> Bad Guaranteed Min US CH Bit rate Configuration setting - Out of Range. CM Mac Addr <[enet]>

REG REQ : Bad Guaranteed Min US CH Bit rate Configuration setting - Out of Range.\n

ubr7200

"Check the Config File Parameters"

UBR7200-4-INVALID_MAX_UPSTREAM_BURST_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011600> Bad Max US CH Transmit Burst Configuration setting - Invalid format. CM Mac Addr <[enet]>

CM Max US channel transmit burst type invalid format.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OUT_OF_RANGE_MAX_UPSTREAM_BURST

4-Warning

<133>CMTS[DOCSIS]:<73011601> Bad Max US CH Transmit Burst Configuration setting - Out of Range. CM Mac Addr <[enet]>

CM Max US channel transmit burst setting out of range.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-INVALID_MODEM_CONFIGURATION_SETTING_FORMAT

4-Warning

<133>CMTS[DOCSIS]:<73011700> Invalid Modem Capabilities configuration setting . CM Mac Addr <[enet]>

CM Capabilities config value contains an invalid format.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OUT_OF_RANGE_CONFIG_FILE_PARAMETERS

4-Warning

<133>CMTS[DOCSIS]:<73011800> Configuration file contains parameter with the value outside of the range. CM Mac Addr <[enet]>

CM config file parameter contains an out of range parameter.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<73020100> REG REQ rejected Unspecified Reason . CM Mac Addr <[enet]>

Unspecified Reason \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<73020101> REG REQ rejected - Unrecognized configuration setting. CM Mac Addr <[enet]>

REG REQ rejected - Unrecognized configuration setting . \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_TEMPORARY_NO_RESOURCE

4-Warning

<133>CMTS[DOCSIS]:<73020102> REG REQ rejected - temporary no resource . CM Mac Addr <[enet]>

REG REQ rejected - temporary no resource . \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_PERMANENT_ADMINISTRATIVE

4-Warning

<133>CMTS[DOCSIS]:<73020103> REG REQ rejected - Permanent administrative . CM Mac Addr <[enet]>

REG REQ rejected - Permanent administrative. \n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<73020104> REG REQ rejected Required parameter not present. CM Mac Addr <[enet]>

Required parameter not present\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-HEADER_SUPPRESSION_SETTING_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<73020105> REG REQ rejected Header suppression setting not supported. CM Mac Addr <[enet]>

Header suppression setting not supported\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<73020106> REG REQ rejected - Multiple errors. CM Mac Addr <[enet]>

CM Registration Request msg contains multile errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<73020107> REG REQ rejected duplicate reference-ID or index in message . CM Mac Addr <[enet]>

CM Registration Request message contains a duplicate ID or index.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_PARAM_INVALID

4-Warning

<133>CMTS[DOCSIS]:<73020108> REG REQ rejected parameter invalid for context. CM Mac Addr <[enet]>

CM Registration Request conatins a invalide parameter for context.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_AUTH_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<73020109> REG REQ rejected - Authorization failure . CM Mac Addr <[enet]>

CM Registration Request Authorization failure.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020110> REG REQ rejected - Major service flow error . CM Mac Addr <[enet]>

CM Registration Request service flow error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_CLASSIFIER_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020111> REG REQ rejected - Major classifier error . CM Mac Addr <[enet]>

CM Registration Request classifier error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020112> REG REQ rejected - Major PHS rule error . CM Mac Addr <[enet]>

CM Registration Request PHS rule error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MAJOR_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<73020113> REG REQ rejected - Multiple major errors. CM Mac Addr <[enet]>

CM Registration Request mulitiple errors.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020114> REG REQ rejected - Message syntax error . CM Mac Addr <[enet]>

CM Registration Request syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_PRIM_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73020115> REG REQ rejected - Primary service flow error. CM Mac Addr <[enet]>

CM Registration Request primary service flow error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_REQ_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<73020116> REG REQ rejected - Message too big. CM Mac Addr <[enet]>

CM Registration Request message to large.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REGISTRATION_ABORT_NO_REG_ACK

4-Warning

<133>CMTS[DOCSIS]:<73030100> REG aborted no REG-ACK. CM Mac Addr <[enet]>

CM Reg aborted. No CM REG_ACK message.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_ACK_REJ_UNSPECIFIED

4-Warning

<133>CMTS[DOCSIS]:<73030200> REG ACK rejected unspecified reason. CM Mac Addr <[enet]>

CM Reg Ack message rejected.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_ACK_REJ_BAD_RCC

4-Warning

<133>CMTS[DOCSIS]:<73030208> REG ACK rejected bad rcc. CM Mac Addr <[enet]>

CM Reg Ack message bad rcc.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-REG_ACK_REJ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<73030300> REG ACK rejected message syntax error. CM Mac Addr <[enet]>

CM Reg Ack message syntax error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSA_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<83000100> Service Add is rejected - Unspecified reason. CM MAC addr <[enet]>

Unspecified reason \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83000101> Service Add is rejected - Unrecognized configuration setting. CM MAC addr <[enet]>

Unrecognized configuration setting \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_TEMP_NO_RESOURCE

4-Warning

<133>CMTS[DOCSIS]:<83000102> Service Add is rejected - Temporary no resource.CM MAC addr <[enet]> [chars]

CM DSA message is rejected due to no resources.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_PERMANENT_ADMINISTRATIVE

4-Warning

<133>CMTS[DOCSIS]:<83000103> Service Add is rejected - Permanent administrative.CM MAC addr <[enet]> [chars]

Permanent administrative \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83000104> Service Add is rejected - Required parameter not present. CM MAC addr <[enet]>

Required parameter is not present\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_HEADER_SUPPR_SETTING_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<83000105> Service Add is rejected - Header suppression setting not supported. CM MAC addr <[enet]>

Header suppression setting is not supported\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_SERVICE_FLOW_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000106> Service Add rejected - Service flow exists. CM MAC addr <[enet]>

CM DSA is rejected because service flow exists.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_HMAC_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000101> Service Add is rejected - HMAC authentication failure. CM MAC addr <[enet]>

HMAC Authentication Failure \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_ADD_ABORTED

4-Warning

<133>CMTS[DOCSIS]:<83000108> Service Add is rejected - Add aborted. CM MAC addr <[enet]>

CM DSA message is rejected.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000109> Service Add is rejected - Multiple errors. CM MAC addr <[enet]>

CM DSA is rejected due to multilpe errors.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_CLASSIFIER_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000110> Service Add is rejected - Classifier not found. CM MAC addr <[enet]>

CM DSA is rejected because classifier was not found.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_CLASSIFIER_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000111> Service Add is rejected - Classifier exists. CM MAC addr <[enet]>

CM DSA is rejected because classifier already exists.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_PHS_RULE_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000112> Service Add is rejected - PHS rule not found. CM MAC addr <[enet]>

CM DSA is rejected because the PHS rule was not found.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000113> Service Add is rejected - PHS rule exists. CM MAC addr <[enet]>

CM DSA is rejected because the PHS rule already exists.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<83000114> Service Add is rejected - Duplicated reference-ID or index in message. CM MAC addr <[enet]>

CM DSA is rejected because of duplicated reference ID or index.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MULTIPLE_UPSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000115> Service Add is rejected - Multiple upstream flow. CM MAC addr <[enet]>

CM DSA is rejected because of muliptle US flows.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MULTIPLE_DOWNSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000116> Service Add is rejected - Multiple downstream flow. CM MAC addr <[enet]>

CM DSA is rejected because of mulitple DS flows.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_CLASSIFIER_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000117> Service Add is rejected - Classifier for another flow. CM MAC addr <[enet]>

CM DSA is rejected because classifier is for another flow.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_PHS_RULE_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000118> Service Add is rejected - PHS rule for another flow. CM MAC addr <[enet]>

CM DSA is rejected because PHS rule is for another flow.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83000119> Service Add is rejected - Parameter invalid for context. CM MAC addr <[enet]>

CM DSA is rejected because parameter is invalid for the context.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_AUTH_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000120> Service Add is rejected - Authorization failure. CM MAC addr <[enet]>

CM DSA is rejected because of an authorization failure.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000121> Service Add is rejected - Major service flow error. CM MAC addr <[enet]>

CM DSA is rejected because of a major service flow error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_CLASSIFIER_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000122> Service Add is rejected - Major classifier error. CM MAC addr <[enet]>

CM DSA is rejected because of a major classifier error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000123> Service Add rejected - Major PHS rule error. CM MAC addr <[enet]>

CM DSA is rejected because of a major PHS rule error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MAJOR_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000124> Service Add is rejected - Multiple major errors. CM MAC addr <[enet]>

CM DSA is rejected because of multiple major errors.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000125> Service Add is rejected - Message syntax error. CM MAC addr <[enet]>

CM DSA is rejected because of message syntax error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83000126> Service Add is rejected - Message too big. CM MAC addr <[enet]>

CM DSA is rejected because message length was too big.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<83000200> Service Change is rejected - Unspecified reason. CM MAC addr <[enet]>

Unspecified reason \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83000201> Service Change is rejected - Unrecognized configuration setting. CM MAC addr <[enet]>

Unrecognized configuration setting \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_TEMP_NO_RESOURCE

4-Warning

<133>CMTS[DOCSIS]:<83000202> Service Change is rejected - Temporary no resource. CM MAC addr <[enet]> [chars]

CM DSC is rejected because of no resource.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_PERMANENT_ADMINISTRATIVE

4-Warning

<133>CMTS[DOCSIS]:<83000203> Service Change is rejected - Permanent administrative. CM MAC addr <[enet]> [chars]

Permanent administrative \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_REQUESTOR_NOT_OWNER

4-Warning

<133>CMTS[DOCSIS]:<83000204> Service Change is rejected - Requestor not the owner of service flow. CM MAC addr <[enet]>

Requestor is not the owner of service flow\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83000206> Service Change is rejected - Required parameter not present. CM MAC addr <[enet]>

Required parameter is not present\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_SERVICE_FLOW_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000205> Service Change is rejected - Service flow not found. CM MAC addr <[enet]>

Service flow is not found\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_HEADER_SUPPR_SETTING_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<83000207> Service Change is rejected - Header suppression setting not supported. CM MAC addr <[enet]>

Header suppression setting is not supported\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_HMAC_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000208> Service Change is rejected - HMAC authorization failure. CM MAC addr <[enet]>

HMAC Authentication Failure \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000209> Service Change is rejected - Multiple errors. CM MAC addr <[enet]>

CM DSC is rejected because mulitple errors have already occurred.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_CLASSIFIER_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000210> Service Change is rejected - Classifier not found. CM MAC addr <[enet]>

CM DSC is rejected because classifier is not found.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_CLASSIFIER_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000211> Service Change is rejected - Classifier exists. CM MAC addr <[enet]>

CM DSC is rejected because classifier has been exist.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_PHS_RULE_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000212> Service Change is rejected - PHS rule not found. CM MAC addr <[enet]>

CM DSC is rejected because PHS rule can't be found.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83000213> Service Change is rejected - PHS rule exists. CM MAC addr <[enet]>

CM DSC is rejected because PHS rule exists.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<83000214> Service Change is rejected - Duplicated reference-ID or index in message. CM MAC addr <[enet]>

CM DSC is rejected because of duplicated reference ID or index.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MULTIPLE_UPSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000215> Service Change is rejected - Multiple upstream flow. CM MAC addr <[enet]>

CM DSC is rejected because of multiple US flows.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MULTIPLE_DOWNSTREAM_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000216> Service Change is rejected - Multiple downstream flow. CM MAC addr <[enet]>

CM DSC is rejected because of mulitple DS flows.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_CLASSIFIER_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000217> Service Change rejected - Classifier for another flow. CM MAC addr <[enet]>

CM DSC is rejected because classifier is for another flow.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_PHS_RULE_ANOTHER_FLOW

4-Warning

<133>CMTS[DOCSIS]:<83000218> Service Change is rejected - PHS rule for another flow. CM MAC addr <[enet]>

CM DSC is rejected because PHS rule is for another flow.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83000219> Service Change rejected - Invalid parameter for context. CM MAC addr <[enet]>

CM DSC rejected because of invalid parameter for context.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_AUTH_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000220> Service Change is rejected - Authorization failure. CM MAC addr <[enet]>

CM DSC is rejected because authorization failed.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_SRV_FLOW_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000221> Service Change is rejected - Major service flow error. CM MAC addr <[enet]>

CM DSC is rejected because service flow error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_CLASSIFIER_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000222> Service Change is rejected - Major classifier error. CM MAC addr <[enet]>

CM DSC is rejected because major classifier error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000223> Service Change is rejected - Major PHS rule error. CM MAC addr <[enet]>

CM DSC is rejected because major PHS rule error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MAJOR_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<83000224> Service Change is rejected - Multiple major errors. CM MAC addr <[enet]>

CM DSC is rejected because of mulitple major errors.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000225> Service Change is rejected - Message syntax error. CM MAC addr <[enet]>

CM DSC is rejected because message syntax error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83000226> Service Change is rejected - Message too big. CM MAC addr <[enet]>

CM DSC is rejected because message length is too big.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSD_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<83000300> Service Delete is rejected - Unspecified reason. CM MAC addr <[enet]>

Unspecified reason \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSD_REQUESTOR_NOT_OWNER

4-Warning

<133>CMTS[DOCSIS]:<83000301> Service Delete is rejected - Requestor not the owner of service flow. CM MAC addr <[enet]>

Requestor is not the owner of service flow\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSD_SERVICE_FLOW_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<83000302> Service Delete is rejected - Service flow not found. CM MAC addr <[enet]>

Service flow was not found\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSD_HMAC_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83000303> Service Delete is rejected - HMAC authorization failure. CM MAC addr <[enet]>

HMAC authentication failure \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSD_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83000304> Service Delete is rejected - Message syntax error. CM MAC addr <[enet]>

CM DSD is rejected because of message syntax error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_ACK_REJECTED_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83020100> Service Add Response is rejected - Invalid transaction ID. CM MAC addr <[enet]>

ACK is rejected because of invalid transaction ID \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_ACK_REJECTED_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83020200> Service Change ACK is rejected - Invalid transaction ID. CM MAC addr <[enet]>

ACK is rejected because of invalid transaction ID \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_ABORTED_NO_ACK

4-Warning

<133>CMTS[DOCSIS]:<83020101> Service Add is aborted - No ACK. CM MAC addr <[enet]>

DSX is aborted because no ACK \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_ABORTED_NO_ACK

4-Warning

<133>CMTS[DOCSIS]:<83020201> Service Change is aborted - No ACK. CM MAC addr <[enet]>

DSX is aborted because no ACK \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83010100> Service Add Response is rejected - Invalid transaction ID. CM MAC addr <[enet]>

CM DSA response is rejected because of invalid transation ID.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_ABORTED_NO_RSP

4-Warning

<133>CMTS[DOCSIS]:<83010101> Service Add is aborted - No response. CM MAC addr <[enet]>

CM DSA is aborted because no response.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_ABORTED_NO_RSP

4-Warning

<133>CMTS[DOCSIS]:<83010201> Service Change is aborted - No response. CM MAC addr <[enet]>

CM DSC is aborted because no response.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83010200> Service Change Response is rejected - Invalid transaction ID. CM MAC addr <[enet]>

CM DSC response is rejected because of an invalid transation ID.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_AUTHORIZATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<83010202> Service Change Response is rejected - HMAC authorization failure. CM MAC addr <[enet]>

CM DSA response is rejected because of authorization failure.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83010205> Service Change response is rejected - Unrecognized configuration setting. CM MAC addr <[enet]>

CM DSC response is rejected because of unrecognized configuration setting.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_REQD_PARAM_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83010206> Service Change Response is rejected - Required parameter not present. CM MAC addr <[enet]>

CM DSC response is rejected because the required parameter not present.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83010209> Service Change Response is rejected - PHS rule exists. CM MAC addr <[enet]>

CM DSC response is rejected because of a major PHS rule error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_DUPLC_REF_ID_OR_INDEX

4-Warning

<133>CMTS[DOCSIS]:<83010210>Service Change Response is rejected - Duplicated reference-ID or index in message. CM MAC addr <[enet]>

CM DSC response is rejected because of duplicated refrence ID or index.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83010211> Service Change Response is rejected - Invalid parameter for context. CM MAC addr <[enet]>

CM DSC response is rejected because of invalid parameter for context.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MAJOR_CFR_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010212> Service Change Response is rejected - Major classifier error. CM MAC addr <[enet]>

CM DSC response is rejected because of a major classifier error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010213> Service Change Response is rejected - Major PHS rule error. CM MAC addr <[enet]>

CM DSC response is rejected because of a major PHS error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83010215> Service Change Response is rejected - Message too big. CM MAC addr <[enet]>

CM DSC response is rejected because message length was too big.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSC_RSP_REJECT_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010203> Service Change Response is rejected - Message syntax error. CM MAC addr <[enet]>

CM DSC response is rejected because of a message syntax error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSD_RSP_REJECTED_INVALID_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<83010300> Service Delete Response is rejected - Invalid transaction ID. CM MAC addr <[enet]>

DSD response is rejected because of invalid transaction ID\n

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_UNRECOGNIZED_CONFIGURATION_SETTING

4-Warning

<133>CMTS[DOCSIS]:<83010105> Service Add Response is rejected - Unrecognized configuration setting. CM MAC addr <[enet]>

CM DSA response is rejected because of unrecognized configuration setting.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_REQD_PARAM_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<83010106> Service Add Response is rejected - Required parameter not present. CM MAC addr <[enet]>

CM DSA response is rejected because the required parameter is not present.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_PHS_RULE_EXISTS

4-Warning

<133>CMTS[DOCSIS]:<83010110> Service Add Response is rejected - PHS rule exists. CM MAC addr <[enet]>

CM DSA response is rejected because the PHS rule already exist.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_PARAM_INVALID_FOR_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<83010113> Service Add Response is rejected - Invalid parameter for context. CM MAC addr <[enet]>

CM DSA response is rejected because of invalid parameter for context

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_MAJOR_CFR_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010115> Service Add Response is rejected - Major classifier error. CM MAC addr <[enet]>

CM DSA response is rejected because of a major classifier error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_MAJOR_PHS_RULE_ERROR

4-Warning

<133>CMTS[DOCSIS]:<83010116> Service Add Response is rejected - Major PHS rule error. CM MAC addr <[enet]>

CM DSA response is rejected because of a major PHS rule error.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSA_RSP_REJECT_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<83010118> Service Add Response is rejected - Message length too big. CM MAC addr <[enet]>

CM DSA response is rejected because message length was too big.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSX_RESTORE_INVALID_CFRID

4-Warning

Invalid classifier ID was found when DSX restore classifier state. CM MAC addr <[enet]>

DSX restore classifier state because invalid classifier ID was found.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DSX_RESTORE_CFR_STATE_FAILED

4-Warning

DSX restore classifier state fail when try to restore state. CM MAC addr <[enet]>

DSX restore classifier state fail.

cbr-application

LOG_STD_NO_ACTION

UBR7200-3-DSX_DUP_TRANSC_SAME_ID

3-Error

[chars] Err: [enet] [dec] [chars]/[chars] [dec]/[dec] [dec]/[dec]

Duplicated DSX transaction with the same ID.

cbr-application

LOG_STD_SH_TECH_ACTION

CM_REDUC_MODE-4-DBC_REJECT_CAUSE_CM_OFFLINE

4-Warning

CM [enet] forcely offline because the operation failed as DBC rejected the invalid request DBC client [dec]

DBC failed to change CM BG because the operation was rejected as one invalid request. That cause the CM was not permitted to register again to the original BG. Mark CM offline to avoid CM stuck in reduce mode

cbr-application

LOG_STD_NO_ACTION

CM_REDUC_MODE-4-BM_ATTR_NOT_MAINTAIN

4-Warning

Attribute masks are not maintained when entering battery mode. CM MAC addr <[enet]>

Attribute masks are not maintained when entering battery mode \n

cbr-application

LOG_STD_NO_ACTION

CM_REDUC_MODE-4-BM_OPERATION_EXCEED_MAX_COUNT

4-Warning

Enter into/exit BM mode failed for CM MAC addr <[enet]>

There maybe resource limitation which induce BM operation failure.\n

cbr-application

LOG_STD_NO_ACTION

CM_REDUC_MODE-4-EM_ATTR_NOT_MAINTAIN

4-Warning

Attribute masks are not maintained when entering EM mode. CM MAC addr <[enet]>

Attribute masks are not maintained when entering EM mode \n

cbr-application

LOG_STD_NO_ACTION

CM_REDUC_MODE-4-EM_NO_AVAILABLE_DBG

4-Warning

Entering EM mode failed since no available RBG. CM MAC addr <[enet]>

Entering EM mode failed since no available RBG \n

cbr-application

"Please inspect the configuration file"

CM_REDUC_MODE-4-EM_INVALID_EM_REQ

4-Warning

Receive an invalid EM request message from CM MAC addr <[enet]> request power mode [dec].

Receive invalid requested power mode from CM\n

cbr-application

LOG_STD_NO_ACTION

CM_REDUC_MODE-4-BM_NO_AVAILABLE_DBG

4-Warning

Entering battery mode failed since no available RBG. CM MAC addr <[enet]>

Entering battery mode failed since no available RBG \n

cbr-application

"Please inspect the configuration file and configured " "available RBG"

CM_REDUC_MODE-4-BM_ORG_RCC_INAVAILABLE

4-Warning

Exiting battery mode failed since original rcc unavailable. CM MAC addr <[enet]>

Exiting battery mode failed since original rcc unavailable \n

cbr-application

LOG_STD_NO_ACTION

UBR7200-3-INVALID_BP_CONFIGURATION_SETTING_VALUE

3-Error

<132>CMTS[DOCSIS]:<66010200> Invalid BP Configuration Setting Value for TLV type [dec]. CM MAC Addr <[enet]>

Invalid BP Configuration Setting Value \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-EXCESSIVE_SAV_GROUP_IDS

5-Notice

More than 1 SAV Group ID in registration request for CM MAC <[enet]>. Ignoring the excessive group ids

There may be more than 1 SAV Group IDs specified in the in the configuration file\n

ubr7200

"Please inspect the configuration file"

UBR7200-5-EXCESSIVE_SAV_PREFIXES

5-Notice

More than [dec] SAV prefixes in the registration request for CM MAC <[enet]>. Ignoring the excessive prefixes

There are excessive number of SAV prefixes in the configuration file\n

ubr7200

"Please inspect the configuration file"

UBR7200-5-MALFORMED_MODEM_TLV

5-Notice

PARSER-ERR: Next TLV type=[dec] steps beyond end of TLV block.\n\t

Malformed TLV found in parsing\n

ubr7200

"Please check if the modem's behavior is correct"

UBR7200-3-CM_CERTIFICATE_FORMAT_ERROR

3-Error

<133>CMTS[DOCSIS]: CM Certificate Format Error

CM Certificate Format Error \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MANUFACTURE_CA_CM_CERTIFICATE_FORMAT_ERROR

3-Error

<133>CMTS[DOCSIS]: CM MAC Addr <[enet]> on Interface [chars] U[dec] : [chars]

Manufacture CA Certificate Format Error \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-CM_CERTIFICATE_SELF_VERFICATION_ERROR

3-Error

<133>CMTS[DOCSIS]:<0> CM Certificate Self-Verfication Error

CM Certificate Self-Verfication Error \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66030102> Auth Reject - No Information . CM Mac Addr <[enet]>

Auth Reject No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_UNAUTHORIZED_CM

3-Error

<132>CMTS[DOCSIS]:<66030103> Auth Reject - Unauthorized CM . CM Mac Addr <[enet]>

Auth Reject Unauthorized CM\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_UNAUTHORIZED_SAID

3-Error

<132>CMTS[DOCSIS]:<66030104> Auth Reject - Unauthorized SAID. CM Mac Addr <[enet]>

Auth Reject Unauthorized SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_PERMANENT_AUTHORIZATION_FAILURE

3-Error

<132>CMTS[DOCSIS]:<66030108> Auth Reject - Permanent Authorization Failure . CM Mac Addr <[enet]>

Auth Reject Permanent Authorization Failure\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_REJECT_TOD_NOT_ACQUIRED

3-Error

<132>CMTS[DOCSIS]:<66030109> Auth Reject - Time of Day not acquired . CM Mac Addr <[enet]>

CM Auth Rejected. TOD not acquired.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-CM_CERTIFICATE_ERROR

3-Error

<132>CMTS[DOCSIS]:<66030111> CM Certificate Error. CM Mac Addr <[enet]>

CM Certificate error.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66030202> Auth Invalid - No Information. CM Mac Addr <[enet]>

Auth Invalid No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_UNAUTHORIZED_CM

3-Error

<132>CMTS[DOCSIS]:<66030203> Auth Invalid - Unauthorized CM. CM Mac Addr <[enet]>

Auth Invalid Unauthorized CM\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_UNSOLICITED

3-Error

<132>CMTS[DOCSIS]:<66030205> Auth Invalid - Unsolicited. CM Mac Addr <[enet]>

Auth Invalid Unsolicited\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_INVALID_KEY_SEQUENCE_NUMBER

3-Error

<132>CMTS[DOCSIS]:<66030206> Auth Invalid - Invalid Key Sequence Number. CM Mac Addr <[enet]>

Auth Invalid-Invalid Key Sequence Number\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-AUTH_INVALID_MESSAGE_AUTHENTICATION_FAILURE

3-Error

<132>CMTS[DOCSIS]:<66030207> Auth Invalid - MessageKey Request Authentication Failure . CM Mac Addr <[enet]>

Auth Invalid Message Authentication Failure\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-UNSUPPORTED_CRYPTO_SUITE

3-Error

<132>CMTS[DOCSIS]:<66030300> Unsupported Crypto Suite. CM Mac Addr <[enet]>

Unsupported Crypto Suite\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-CRL_NOT_RESPONDING

4-Warning

<132>CMTS[DOCSIS]:<66030400> Failed to retrieve CRL from [chars]

CRL not available\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-OCSP_NOT_RESPONDING

4-Warning

<132>CMTS[DOCSIS]:<66030401> Failed to retrieve OCSP status

OCSP not available\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-MISMATCH_BP_CONFIGURATION_SETTING_VALUE

4-Warning

<132>CMTS[DOCSIS]: Misconfigured BPI Setting: gracetime Type [dec] is longer than 50%% of lifetime. CM MAC Addr <[enet]>

Misconfigured BPI Configuration Setting Value \n

ubr7200

"Please inspect the configuration file"

UBR7200-4-MISMATCH_BP_REVOCATION_TIMEOUT_VALUE

4-Warning

<132>CMTS[DOCSIS]: Misconfigured BPI Setting: [chars] Type [dec] is longer than revocation timeout value. CM MAC Addr <[enet]>

Misconfigured BPI Configuration Setting Value \n

ubr7200

"Please inspect the configuration file"

UBR7200-3-KEY_REJECT_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66050102> Key Reject - No Information. CM Mac Addr <[enet]>

Key Reject No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-KEY_REJECT_UNAUTHORIZED_SAID

3-Error

<132>CMTS[DOCSIS]:<66050103> Key Reject - Unauthorized SAID. CM Mac Addr <[enet]>

Key Reject Unauthorized SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-TEK_INVALID_NO_INFORMATION

3-Error

<132>CMTS[DOCSIS]:<66050203> TEK Invalid - No Information. CM Mac Addr <[enet]>

TEK Invalid No Information\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-TEK_INVALID_INVALID_KEY_SEQUENCE_NUMBER

3-Error

<132>CMTS[DOCSIS]:<66050206> TEK Invalid - Invalid Key Sequence Number . CM Mac Addr <[enet]>

TEK Invalid - Invalid Key Sequence Number\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-BPI_WARNING

4-Warning

[chars]: SID=[dec] KeySeq=0x[hec] Cable Interface <[chars]>

BPI Warning \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-BPI_ERR

3-Error

[chars] [dec] [dec] [dec]

BPI Error \n

ubr10000

LOG_STD_NO_ACTION

UBR7200-3-SA_MAP_UNSUPPORTED_CRYPTO_SUITE

3-Error

<132>CMTS[DOCSIS]:<66060200> Unsupported Crypto Suite. CM Mac Addr <[enet]>

Unsupported Crypto Suite\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAP_REJECT_NOT_AUTH_DS_TRAFFIC

3-Error

<132>CMTS[DOCSIS]:<66060509> Map Reject - Not Authorized for requested downstream traffic flow. CM Mac Addr <[enet]>

Map Reject - Not Authorized for requested downstream traffic flow \n

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-MAP_REJECT_DS_TRAFFIC_FLOW_NOT_MAPPED

6-Information

<132>CMTS[DOCSIS]:<66060510> Map Reject - Downstream traffic flow not mapped to BPI+SAID. CM Mac Addr <[enet]>

Map Reject - Downstream traffic flow not mapped to BPI+SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAPPED_TO_EXISTING_SAID

3-Error

<132>CMTS[DOCSIS]:<66060600> Mapped to existing SAID. CM Mac Addr <[enet]>

Mapped to existing SAID\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAPPED_TO_NEW_SAID

3-Error

<132>CMTS[DOCSIS]:<66060700> Mapped to new SAID. CM Mac Addr <[enet]>

Mapped to new SAID \n

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-3-BPI_ERR_DOCSIS

3-Error

[chars] [enet] [dec] [dec]

BPI DMP Error \n

ubr7200

"Check BPI DMP Module"

UBR7200-3-BPI_ERR_UMP

3-Error

[chars] [enet] [dec] [dec]

BPI UMP Error \n

ubr7200

"Check BPI UMP Module"

UBR7200-4-DCC_REQ_REJ_ALREADY

4-Warning

<133>CMTS[DOCSIS]:<67020100> DCC is rejected - CM MAC address <[enet]> already on destination.

DCC is rejected because CM MAC address is already on destination

cbr-application

"Wait until the transaction ends. Otherwise try to move the modem on another channel."

UBR7200-4-DCC_REQ_DEPART_OLD

4-Warning

<133>CMTS[DOCSIS]:<67020200> DCC departs old channel. CM MAC addr <[enet]>

DCC departs old channel

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REQ_ARRIVE_NEW

4-Warning

<133>CMTS[DOCSIS]:<67020300> DCC arrives new channel. CM MAC addr <[enet]>

DCC arrives new channel

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REQ_ABORT_NO_COMM_NEW_UPSTREAM_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<67020600> DCC is aborted - Unable to communicate on new upstream channel. CM MAC addr <[enet]>

DCC is aborted unable to communicate on new upstream channel

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<67020700> DCC is rejected - Unspecified reason. CM MAC addr <[enet]>

DCC is rejected because of unspecified reason

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_PERMANENT_DCC_NOT_SUPPORTED

4-Warning

<133>CMTS[DOCSIS]:<67020800> DCC is rejected permanently - DCC not supported. CM MAC addr <[enet]>

DCC is rejected permanently because DCC is not supported

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_REQUIRED_PARAMETER_NOT_PRESENT

4-Warning

<133>CMTS[DOCSIS]:<67021000> DCC is rejected - Required parameter not present. CM MAC addr <[enet]>

DCC is rejected because required parameter is not present

cbr-application

"Double check the parameters while sending the DCC request message"

UBR7200-4-DCC_REJ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<67021700> DCC is rejected - Message syntax error. CM MAC addr <[enet]>

DCC is rejected because of message syntax error

cbr-application

"Check the TLV and parameters setting while sending the DCC request message"

UBR7200-4-DCC_REJ_MSG_TOO_BIG

4-Warning

<133>CMTS[DOCSIS]:<67021800> DCC is rejected - Message length too big. CM MAC addr <[enet]>

DCC is rejected because message length is too big

cbr-application

"Mimimize the message length to be less than 1536"

UBR7200-4-DCC_REJ_20_DISABLE

4-Warning

<133>CMTS[DOCSIS]:<67021900> DCC is rejected - DOCSIS 2.0 mode is disabled. CM MAC addr <[enet]>

DCC is rejected because DOCSIS 2.0 mode is disabled

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<67021100> DCC is rejected - Authentication failure. CM MAC addr <[enet]>

DCC is rejected because of authentication failure

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_SRV_FLOW_NOT_FOUND

4-Warning

<133>CMTS[DOCSIS]:<67020900> DCC is rejected - Service flow not found. CM MAC addr <[enet]>

DCC is rejected because service flow was not found

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_MULTIPLE_ERRORS

4-Warning

<133>CMTS[DOCSIS]:<67021200> DCC is rejected - Multiple errors. CM MAC addr <[enet]>

DCC is rejected because of multiple errors

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_DUPLICATE_REF_ID_INDEX

4-Warning

<133>CMTS[DOCSIS]:<67021500> DCC is rejected - Duplicated service flow reference-ID or index in message. CM MAC addr <[enet]>

DCC is rejected because duplicated service flow reference-ID or index exists in message

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_REJ_PARAMETER_INVALID_CONTEXT

4-Warning

<133>CMTS[DOCSIS]:<67021600> DCC is rejected - Invalid parameter for context. CM MAC addr <[enet]>

DCC is rejected because of invalid parameter for contex

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_RSP_NOT_RCV_OLD_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<67030100> DCC response was unreceived on old channel. CM MAC addr <[enet]>

DCC response was unreceived on old channel

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_RSP_NOT_RCV_NEW_CHANNEL

4-Warning

<133>CMTS[DOCSIS]:<67030200> DCC response was unreceived on new channel. CM MAC addr <[enet]>

DCC response was unreceived on new channel

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_RSP_REJ_UNSPECIFIED_REASON

4-Warning

<133>CMTS[DOCSIS]:<67030300> DCC Response is rejected - Unspecified reason. CM MAC addr <[enet]>

DCC response is rejected because of unspecified reason

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_RSP_REJ_UNKNOWN_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<67030400> DCC Response is rejected - Unknown transaction ID. CM MAC addr <[enet]>

DCC response is rejected because of unknown transaction ID

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_RSP_REJ_MSG_SYNTAX_ERROR

4-Warning

<133>CMTS[DOCSIS]:<67030600> DCC Response is rejected - Message syntax error. CM MAC addr <[enet]>

DCC response is rejected because of message syntax error

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_RSP_REJ_AUTHENTICATION_FAILURE

4-Warning

<133>CMTS[DOCSIS]:<67030500> DCC Response is rejected - Authentication failure. CM MAC addr <[enet]>

DCC response is rejected because of authentication failure

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-DCC_ACK_REJ_UNKNOWN_TRANSACTION_ID

4-Warning

<133>CMTS[DOCSIS]:<67040300> DCC-ACK is rejected - Unknown transaction ID. CM MAC addr <[enet]>

DCC-ACK is rejected because of unknown transaction ID

cbr-application

LOG_STD_NO_ACTION

UBR7200-5-KEEPALIVE

5-Notice

Keepalive shutting down interface [chars].

No activity detected within the Keepalive timeout period on the interface.

ubr7200

"Check RF path for failure."

UBR7200-6-MACCLTCLR

6-Information

Enable mac mgmt msg processing on [chars].

The RP has reenabled the sending of DOCSIS MAC-layer messages on the cable interfaces after an N+1 switchover.

ubr7200

"No action needed."

UBR7200-3-FPSUBINIT

3-Error

Unable to create subinterface [chars] for hw interface [chars]

The system was unable to create the cable subinterface data structures

ubr7200

"Gather information about running configuration and amount of memory " "in the system and file a bug"

UBR7200-3-LB_MODEM_FAILED

3-Error

Failed to move modem [enet] from [chars] to [chars].

Load balance failed to move the modem from one interface to another.

cbr-application

"Check if any other modem can be online with this interface " "then check the path of RF channel " "and check if upstream and downstream channels are associated " "as expected in topology"

UBR7200-3-LB_IF_DISABLED

3-Error

Disabled interface [chars]

Load balance disabled the interface because this could not move any modem in and out of it.

cbr-application

"Check if any modem can be online with this interface " "then check the path of RF channel " "and check if upstream and downstream channels are associated " "as expected in topology"

UBR7200-3-LB_STALE_PENDING_CM

3-Error

This is a pre-exist pending entry detailed information as: [enet] action 0x[hec]:0x[hec] client [dec]:[dec] count update flag [dec]

Stale pending CM exist

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-4-LB_CM_LIST_DUP_ENTRY

4-Warning

Duplicated CM [enet] in CM List 0x[hec] group [dec]

Duplicated entries in CM lists. No operational impact.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-LB_CM_LIST_MISMATCH_ENTRY

4-Warning

CM [enet] on CM List 0x[hec] group [dec] action [dec] not matched the

Entry in CM list seen at different position than expected . There is no operational impact

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-4-LB_CM_WITH_INVALID_GROUP_ID

4-Warning

The CM [enet] MD [chars] LBLoad Balance group [dec] is not found in load balance database

The CM is assigned to an invalid load-balance group. No operational impact.

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-LB_COUNT_OUT_OF_RANGE

4-Warning

LBLoad Balance Counter out of range: group [dec] MD [chars] [chars] chan [dec] CM [enet]

LB modem counter is out of decrements range.

cbr-application

LOG_STD_NO_ACTION

UBR7200-3-PKTCBL_INVALID_GATE_ID

3-Error

if_index_db is null index = [dec] gid = [dec]

PacketCable encounters invalid gate id to look up from its DB

packetcable

"SW code path errors"

UBR7200-6-PKTCBL_COPS_CONNECTION_DOWN

6-Information

Cops connection: IP addr: [inet] Handle: 0x[hec] went down Error code: [dec]

Cops connection went down

packetcable

"Check cops connection"

UBR7200-6-PKTCBL_COPS_CONNECTION_UP

6-Information

Cops connection: IP addr: [inet] Handle: 0x[hec] is up

Cops connection is up

packetcable

LOG_STD_NO_ACTION

UBR7200-3-L2VPNMAXLIMIT

3-Error

L2VPN XCONNECT PW max limit of [dec] pseudo-wires reached.

L2VPN XCONNECT PW max limit of pseudo-wires reached.

cmts-application

"Cannot configure anymore pseudo-wires"

UBR7200-4-L2VPN_TLVERR

4-Warning

L2VPN XCONNECT PW Cable Modem CM config file TLV Error.

L2VPN XCONNECT PW TLV Error VCID or SAII or TAII not valid

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_ERROR_BPI_NOT_ENABLED

4-Warning

L2VPN enabled without enabling BPI+ or 1.0 CM [enet] [chars]

Encryption not enabled for L2VPN CM

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_CMIM_ERROR

4-Warning

ERROR: CM [enet] [chars] Top Level CMIM TLV does not exclude eCM

Top Level CMIM TLV does not exclude eCM

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_VPNID_MISSING_ERROR

4-Warning

ERROR: CM [enet] [chars] VPNID TLV missing at top level

VPNID TLV missing at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLSPEERNAME_LEN_ERROR

4-Warning

ERROR: CM [enet] [chars] MPLSPEERNAME TLV length invalid

MPLSPEERNAME TLV length invalid

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_NSI_MISSING_ERROR

4-Warning

ERROR: CM [enet] [chars] VLANID or MPLSPEER TLV missing at top level

VLANID or MPLSPEER TLV missing at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_NSI_DUPLICATE_ERROR

4-Warning

ERROR: CM [enet] [chars] VLANID and MPLSPEER TLV both present at top level

VLANID and MPLSPEER TLV both present at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_VCID_OR_TAII_SAII_MISSING_ERROR

4-Warning

ERROR: CM [enet] [chars] VCID or TAII & SAII TLV missing or out-of-range

VCID or TAII & SAII TLV missing or out-of-range

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_PWTYPE_ERROR

4-Warning

ERROR: CM [enet] [chars] MPLS PW TYPE TLV invalid at top level

MPLS PW TYPE TLV invalid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLSPEER_ERROR

4-Warning

ERROR: CM [enet] [chars] MPLS PEER IPADDR TLV invalid at top level

MPLS PEER IPADDR TLV invalid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MULTIPLE_VPNID_ERROR

4-Warning

ERROR: CM [enet] [chars] Multiple L2VPN TLV with same vpnid at top level

Multiple L2VPN TLV with same vpnid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_DUPLICATE_VLANID_ERROR

4-Warning

ERROR: CM [enet] [chars] Multiple L2VPN TLV with same vlanid at top level

Multiple L2VPN TLV with same vlanid at top level

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_US_SFLOW_VPNID_ERROR

4-Warning

ERROR: CM [enet] [chars] Matching TopLevel L2VPNID not found for US-SF

Matching TopLevel L2VPNID not found for US-SF

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_DS_CFR_VPNID_ERROR

4-Warning

ERROR: CM [enet] [chars] Matching TopLevel L2VPNID not found for DS-CFR

Matching TopLevel L2VPNID not found for DS-CFR

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_BKUP_PRIO_ERR

4-Warning

ERROR: CM [enet] [chars] Incorect or missing priority for backup peer

Priority incorrect or missing for backup peer

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_BKUP_EXCEEDED

4-Warning

ERROR: CM [enet] [chars] Too many backup peers

Too many backup peers

cmts-application

"Check CM config file"

UBR7200-4-L2VPN_MPLS_BKUP_DISABLE_CFG_ERR

4-Warning

ERROR: CM [enet] [chars] Bkup disable delay and never disable bkup both configured

Both TLVs cannot be configured

cmts-application

"Check CM config file"

UBR7200-3-BUN_MCAST_NOFREE_MAC

3-Error

Fail to allocate free Bundle Multicast Map Entry for Bundle:[dec] Group:[inet] Source:[inet] IDB:[chars]

An internal software error occured

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-3-BUN_MCAST_REV_MAP_ERR

3-Error

Unable to find the Multicast Mapped Entry from reverse-mapping table for Bundle: [dec] MAC:[enet]

An internal software error occured

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-3-BUN_MCAST_INIT

3-Error

Unable to allocate memory for bundle multicast initialization.

An internal software error occured

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-6-CONFIG_EXIT

6-Information

Exiting config mode by [chars] since Port Adapter in slot [dec] removed

The user was configuring a port adapter which was either removed from the system or if an mc28u card was reset. Therefore the configuration mode is invalid and terminated by IOS

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DDC_UNEXPECTED_NODES

3-Error

The number of nodes [dec] is invalid

The number of nodes is either smaller or greater than the limits supported by the platform

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-3-DDC_INVALID_STATICMAP

3-Error

The node [dec] for mac-address [enet] exceeds maximum configured nodes

A mapping specified by the oui-map or mac-map commands exceeds the configured number of participant nodes

ddc

"Fix configuration"

UBR7200-4-DDC_CFG_HASHID

4-Warning

Hash id [dec] does not exist in global configuration

A hash id is configured for a cable interface but is not defined globally

ddc

"Fix configuration"

UBR7200-3-DDC_INVALID_HASHTYPE

3-Error

The hash type [dec] for hash id [dec] is invalid

Software does not recognize the configured hash type

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_PROT_FREQ_ERROR

4-Warning

DS frequency not configured for the protect target node [dec]

DS frequencies are not configured for all protect targets

ddc

"Fix configuration"

UBR7200-4-DDC_SEMAPHORE_ERROR

4-Warning

DDC semaphore released when it was not taken

DDC semaphore was not take when release was requested

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_UNEXPECTED_MESSAGE_ERROR

4-Warning

DDC unexpected message error [dec]

DDC received an unexpected or unsupported message

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_UNEXPECTED_EVENT_ERROR

4-Warning

DDC unexpected event error [dec]

DDC received an unexpected or unsupported event

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_MESSAGE_ERROR

4-Warning

DDC message error. type [dec]

DDC failed to send interprocess or IPC message

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_LIST_ERROR

4-Warning

DDC list error

DDC failed to create or add element to list

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_NODE_ID_ERROR

4-Warning

Node id mismatch NPE: [dec] linecard: [dec]

Node id's on NPE subinterface is different than on linecard

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DDC_GENERAL_ERROR

4-Warning

Error: [chars]

Catchall error message for DDC

ddc

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-6-DDC_CFG_HASHFILTER_REMOVED

6-Information

Hash-filter [dec] not present in global config - Filter removed from [chars]\n

The hash-filter was removed from the global config while the card was not present in the chassis therefore the corresponding interface hash filter is removed from the config

ddc

LOG_STD_NO_ACTION

UBR7200-6-DDC_CFG_TARGET_REMOVED

6-Information

Redundancy target invalid - removed from [chars]\n

The router's my_id was config removed while the card was not present in the chassis therefore the redundancy target cli is removed from the interface

ddc

LOG_STD_NO_ACTION

UBR7200-3-ALARM_ERROR

3-Error

[chars]

General error information.

ubr7200

"Copy the error message exactly as it appears and report it to your " "technical support representative."

UBR7200-6-ALARM_INFO

6-Information

[chars] [chars] [chars] [chars] [chars]

Alarm assertion or deassertion information.

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-DISCOVER_FAIL

3-Error

[chars]

Unable to discover physical entity

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-4-DCC_NO_RESOURCE_ON_TARGET

4-Warning

DCC [enet] is aborted - No resource available on target [chars] U[dec]

No resource available on target channel for the DCC transaction

cbr-application

"Check target channel utilization"

UBR7200-5-CLONED_CM_DETECTED

5-Notice

Cloned CM with MAC address [enet] connection attempt rejected on [chars] U[dec]

There might be a hacking attempt going on.

ubr7200

"Look for possible hacking attempt"

UBR7200-3-FLOW_ERR

3-Error

Flow error sfid [dec] sid [dec] CM Mac address <[enet]>

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-DS_FLOW_INCONSIST_WB_INFO

3-Error

DS Flow Error: [chars] [enet] prim_rfid [dec] sfid [dec] wb_mode [dec] forw_chid [dec] [chars]

-

-

-

UBR7200-3-DS_FLOW_INCONSIST_WB_INFO

3-Error

DS Flow Error: [chars] [enet] prim_rfid [dec] sfid [dec] wb_mode [dec] forw_chid [dec] [chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-DIV_BY_ZERO_ERROR

3-Error

Divide by zero attempted error [chars]

An internal software error occurred.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-6-CACHE_ENGINE_BUF_FULL

6-Information

Max. cache buffer has been reached!

Max. cache buffer has been reached. cache engine service for current request is denied.

snmpPerf

"."

UBR7200-4-CACHE_ENGINE_WARNING

4-Warning

Warning: [chars] - [dec]

Cache engine warning message.

snmpPerf

"."

UBR7200-4-SERVICE_FLOW_ERROR

4-Warning

CM MAC: [chars] Service flow direction: [chars] Param code: [dec] Confirm code: [dec]

Looks like issue while admitting/activating Service flow

ubr7200

"Please look for DOCSIS message logs followed for more details"

UBR7200-4-SERVICE_FLOW_ZERO_BLAZE_INDEX_ERROR

4-Warning

spa_num: [dec] spa_if_num: [dec] nb_unique_index: [dec] lc_slot: [dec] lc_subslot: [dec] SFID: [dec] Blaze index: [dec]

Looks like issue while allocating remote downstream blaze index

ubr7200

"Please see show cable modem and " "show int cx/y/z service-flow for more details"

UBR7200-4-SERVICE_FLOW_INDEX_ERROR

4-Warning

[chars] [dec]/[dec] nb_unique_index: [dec] SFID: [dec] index: [dec] flow-chid: [dec] wb-mode: [dec] dsid: [dec] cm [enet]

Looks like issue while allocating remote downstream index

ubr7200

"Please see show cable modem pri and " "show int cx/y/z service-flow for more details"

UBR7200-3-SNMPMALLOC

3-Error

no sufficient memory for sorted table index [dec] allocated %lu unallocated %lu

There is no enough memory to allocate for AVL tree

ubr7200

"No action needed."

UBR7200-4-CLASSIFIER_ERROR

4-Warning

CM MAC: [chars] Classifier direction: [chars] Param code: [dec] Confirm code: [dec]

Looks like issue while admitting/activating Classifier

ubr7200

"Please look for DOCSIS message logs followed for more details"

UBR7200-4-PHS_ERROR

4-Warning

CM MAC: [chars] PHS_ERROR Param code: [dec] Confirm code: [dec]

Looks like issue with PHS header

ubr7200

"Please look for DOCSIS message logs followed for more details"

UBR7200-4-DSX_MSG_ERROR

4-Warning

CM MAC: [chars] MSG type: [chars] Error code: [dec] MSG: [chars].

Received invalid DSX message.

cbr-application

"Please turn on debug to see more detailed DSX messages."

UBR7200-3-MAX_DS_SF_ERROR

3-Error

Maximum limit for downstream service-flows reached

The number of DS service-flows cannot exceed 50

ubr7200

LOG_STD_NO_ACTION

UBR7200-3-MAX_DYN_DS_SF_ERROR

3-Error

Maximum limit for dynamic downstream service-flows reached

The number of dynamic DS service-flows cannot exceed 31

cbr-application

LOG_STD_NO_ACTION

UBR7200-4-CMTS_OIR_INACTIVE_WITHOUT_L2VPN_UNCONFIGURED

4-Warning

Card on [dec]/[dec] with l2vpn \[chars]\ command should be taken care of before plugging different type of card or executing \no card\ command.

Card is configured with cable l2vpn commands please take care of these configurations before plugging different type of card or executing \no card\ command.

cmts-application

"."

UBR7200-6-CM_OFFLINE_WITH_L2VPN_NOT_ENABLE

6-Information

DOCSIS L2VPN not enabled sending CM [enet] offline

Cable Modem is configured with L2VPN but CMTS L2VPN isn't enabled. Send offline message to CM.

cmts-application

"Configure \"cable l2-vpn-service xconnect nsi dot1q interface ..\" and " " \"cable l2-vpn-service nsi dot1q\" commands."

UBR7200-6-CM_OFFLINE_WITH_MPLS_L2VPN_NOT_ENABLE

6-Information

DOCSIS MPLS L2VPN not enabled sending CM [enet] offline

Cable Modem is configured with L2VPN but CMTS MPLS L2VPN isn't enabled. Send offline message to CM.

cmts-application

"Configure \"cable l2-vpn-service xconnect nsi mpls\" command."

UBR7200-6-CM_OFFLINE_WITH_LEGACY_TLS_CONFIGURED

6-Information

Already configured for legacy TLS sending CM [enet] offline

Legacy TLS is already configured. Send offline message to CM.

cmts-application

"Check CMTS configuration for legacy TLS with this CM"

UBR7200-6-CM_OFFLINE_WITH_VLANID_USED

6-Information

VLANID [dec] on [chars] in use sending CM [enet] offline

VLANID is in use. Send offline message to CM.

cmts-application

"Check L2VPN VLANID specified in CM configuration file"

UBR7200-6-CM_OFFLINE_WITH_DUP_MPLSPEER_VCID

6-Information

MPLS PEER [inet] VCID [dec] in use sending CM [enet] offline

MPLS PEER & VCID is in use. Send offline message to CM.

cmts-application

"Check L2VPN MPLS PEER & VCID specified in CM configuration file"

UBR7200-6-CM_OFFLINE_WITH_UNRESOLVED_MPLSPEER_NAME

6-Information

Unable to resolve MPLS NAME [chars] VCID [dec] sending CM [enet] offline

Unable to resolve MPLS NAME via DNS. Send offline message to CM.

cmts-application

"Check L2VPN MPLS PEERNAME specified in CM configuration file" "Or DNS configuration and setup"

UBR7200-6-INTERNAL_XCONNECT_INTERFACE_ERROR

6-Information

Unable to create internal xconnect bundle interface

Unable to find free bundle interface for l2vpn xconnect function

cmts-application

"Free one bundle interface for internal l2vpn xconnect function"

UBR7200-6-CM_OFFLINE_WITH_NO_FREE_VPNID

6-Information

No free VPNIDs remaining sending CM [enet] offline

There aren't any free VPNIDs. Send offline message to CM.

cmts-application

LOG_STD_SH_TECH_ACTION

UBR7200-4-LOCAL_MTU_LESS_THAN_REMOTE_MTU

4-Warning

Local MTU [dec] is lower than remote MTU [dec] PW cannot come up.

Local MTU is lower than remote MTU PW cannot come up

cmts-application

"Check the peer MTU"

UBR7200-4-REMOTE_BACKUP_MTU_NOT_EQL_PRIMARY

4-Warning

Remote backup MTU [dec] is not equal to primary [dec] cannot set up the backup PW

Remote backup MTU is not equal to primary

cmts-application

"Keep same mtu for the primary peer and secondary peer"

UBR7200-3-INVALID_INVOKE_FROM_ISR

3-Error

Invalid [chars] from interrupt level [dec]

Invalid operation from ISR context. Possible recurrence of CSCek63728

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-INVALID_US_CHID

3-Error

Invalid Upstream Channel ID

An internal software error occurred.

cmts-docsis

LOG_STD_SH_TECH_ACTION

UBR7200-4-UCC_RSP_NOT_RCV_ON_CHANNEL_ID

4-Warning

<133>CMTS[DOCSIS]:<67010100> UCC-RSP was not received on previous channel ID. CM MAC addr <[enet]>

-

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-4-UCC_RSP_RCV_INVALID_CHANNEL_ID

4-Warning

<133>CMTS[DOCSIS]:<67010200> UCC-RSP was received with invalid channel ID. CM MAC addr <[enet]>

-

cbr-application

"Enable <cmdBold>debug cable ucc<noCmdBold> at CMTS " "and make sure that CMTS sends UCC-REQ with correct " "channel ID. If CMTS is not sending the correct " "channel ID report the problem"

UBR7200-4-UCC_RSP_RCV_INVALID_CHANNEL_ID_NEW

4-Warning

<133>CMTS[DOCSIS]:<67010300> UCC-RSP was received with invalid channel ID on new channel. CM MAC addr <[enet]>

-

cbr-application

LOG_STD_SH_TECH_ACTION

UBR7200-3-CMTS_TCC_RNG_INVALID_SB

3-Error

TCC RNG on Interface [chars] with invalid SB for CM [enet]

TCC RNG could not get a valid subblock for the interface that the CM is ranged on. SW Bug.

ubr10000

LOG_STD_NO_ACTION

UBR7200-4-CM_SF_DSID_INCONSISTENT

4-Warning

DSID [dec] BG: [dec] assigned to SF:[dec] already. DSID invalid on CM-[enet]

DSID assigned to SF not valid any longer. SW Bug

ubr10000

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-4-DSID_DUPLICATE

4-Warning

Duplicate DSID [dec]/[dec]/[dec]: [dec] detected

Detected an attempt to enqueue a duplicate DSID. SW Bug

ubr10000

"Copy the error message exactly as it appears " "and report it to your technical services representative"

UBR7200-5-ATTRIBUTE_CHANGE_CONFLICT

5-Notice

<133>CMTS[DOCSIS]:<75010100> Attribute Masks for SF SFID %lu do not

Change in provisioned attribute mask causes mismatch

ubr10000

"Modify provisioned attributes such that it meets " "requirements"

UBR7200-4-TEMPLATE_LKUP_ERROR

4-Warning

CM MAC: [enet] Sid: [dec] Act_Qos: [dec]

Problem while looking up qos template

ubr7200

"LOG_STD_SH_TECH_ACTION"

UBR7200-4-DIAG_LOG_HIGH_THRSHLD_REACHED

4-Warning

[DOCSIS]:<86000100>Docs Diag Log exceeds high threshold

Docs Diag Log Notification :log size exceeds high threshold

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-5-DIAG_LOG_LOW_THRSHLD_REACHED

5-Notice

[DOCSIS]:<86000200>Docs Diag Log reaches low threshold

Docs Diag Log Notification :log size reaches low threshold

ubr7200

"LOG_STD_NO_ACTION"

UBR7200-4-DIAG_LOG_FULL_REACHED

4-Warning

[DOCSIS]:<86000300>Docs Diag Log reaches max size

Docs Diag Log Notification: log size reaches max size

ubr7200

-

UBR7200-2-LOG_CON_SYS_CRIT

2-Critical

[chars] logging console level to [dec] from [dec] Rate-limit level [dec] [chars].

Logging console restricted during critical situations

ubr7200

"Please run 'show logging' to view all sys-logged messages"

UBR7200-3-JIB_Q_LENGTH_PHS_ERR_DETECTED

3-Error

JIB Upstream Queue Length or PHS Rule Failure Detected.

-

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-GRD_HCCP_RECOVER

3-Error

Wideband-Cable[dec]/[dec]/[dec]:[dec] not recovered after switchover

After a switchover or revert where the modular-host for a SPA becomes active on the standby a wideband interface on that SPA is not recovered. This is most likely due to a software problem.

cmts-redundancy

LOG_STD_SH_TECH_ACTION

UBR7200-3-GRD_HCCP_REMOVE

3-Error

Wideband-Cable[dec]/[dec]/[dec]:[dec] not removed

When the modular-host configuration for a SPA is removed a wideband interface on that SPA is not removed. This is most likely due to a software problem.

cmts-redundancy

LOG_STD_SH_TECH_ACTION

UBR7200-6-COMPAT_NEW_CARD

6-Information

The old card <[chars]> is replaced by new card <[chars]> in slot [dec].

OIR: card replacement

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-COMPAT_SHUTDOWN_CARD

6-Information

Failed to restore the configuration for [chars].

OIR-compatiblity configuration restore failed

ubr7200

"Configure the interface manually"

UBR7200-4-BLZE_HM_TEST

4-Warning

Blaze HM testcase failed. Blaze indices allocated for MD host [dec]/[dec] on the Guardian [dec]/[dec] : [dec] Blaze indices in use on the MD Host: [dec]

The blaze indices have not been deallocated on the Guardian

ubr10000

LOG_STD_NO_ACTION

UBR7200-4-GRD_UNAVAIL

4-Warning

Unable to reach Card [dec]/[dec] for Modular-host services

The Guardian card is down or the IPC to the Guardian card is down

ubr10000

"Make sure the card selected to be Modular-host is " "operational or change the relevant Modular-host config to" "use an operational card."

UBR7200-4-METERING_NOFILESYS_SFLOG

4-Warning

No file system [chars] can be used for sflog file.

Cannot find a suitable file system to store sflog file.

ubr7200

"Please check whether tmp disk" " is ready or full."

UBR7200-3-IPDR_FILESYS_FULL

3-Error

File [chars] cannot be created/written since filesystem is full.

The IPDR feature requires a file to be written to filesystem. Since filesystem is full it might result in lost IPDR data.

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-IPDR_BUFFER_ERR

3-Error

unable to alloc buffer because percent of free memory is [dec] which is below [dec]

The IPDR feature requires memory to hold record. Since insufficient memory it might result in lost IPDR data

ubr7200

LOG_STD_SH_TECH_ACTION

UBR7200-3-IPDR_GET_MACDOMAIN_ERR

3-Error

The IPDR CM-US failed to get MAC domain with slot[[dec]] subslot[[dec]] slotunit[[dec]].

The IPDR CM-US failed to get MAC domain by docsIf3CmtsCmRegStatusId.

ubr7200

"Ignore this IPDR record collecting " "records at next interval."

UBR7200-3-IPDR_SFLOG_FILE_ERR

3-Error

The IPDR failed to handle file: [chars]

The IPDR failed to handle file

ubr7200

"Check the file system "

UBR7200-4-IPDR_CPETYPE_ENQ_ERR

4-Warning

Enqueue error for CPETYPE event. [chars] Q size [dec]

Too many IPDR CPETYPE events generated in a moment

ubr10000

"If there are a lot of memory leaks" " do PRE switchover."

UBR7200-3-CMTS_QUACK_FAIL_ERR

3-Error

[chars]

This LC requires programmed Quack IDPROM.

ubr10000

LOG_STD_SH_TECH_ACTION

UBR7200-3-UCDPROCERR

3-Error

CMTS UCD processing failed on [chars] U[dec] lch_state [dec] err [dec] retry [dec]

UCD update error

cmts-infra

"Check the system CPU load and reset the upstream"

UBR7200-5-UCDCCCERR

5-Notice

CMTS UCD failed to update CCC on [chars] U[dec] lch_state [dec]

UCD update CCC error

cmts-infra

"Check the lch_state reset the upstream if necessary"

UBR7200-5-USPHYTSSDISC

5-Notice

PHY TSS discontinuous on [chars] U[dec] old<T [hec] M [hec] F [hec]> new<T [hec] M [hec] F %4x> start<T [hec] M [hec] F %4x> mac<T [hec] M [hec] F %4x> tgc/frame [hec] mslot/frame [hec]

PHY TSS error

cmts-infra

"If the problem is persistent modify minislot size and reset the upstream"

UBR7200-5-USPHYTSSLATE

5-Notice

PHY late TSS on [chars] U[dec] MAC [hec] phy <last [hec] curr [hec]> tgc/frame [hec]

late PHY TSS SNAPSHOT messages are received

cmts-infra

"This is an internal failure and not necessarily problematic"

UBR7200-5-USTSSMISMATCH

5-Notice

MAC-PHY TSS mismatch [chars] U[dec]: MAC<T [hec] M [hec] F [hec]> PHY<T [hec] M [hec] F [hec]> Old-PHY<T [hec] M [hec] F [hec]> start<T [hec] M [hec] F [hec]> curr [hec] tgc/fame [hec] mslots/fame [hec]

Mis-matched MAC-PHY TSS is detected

cmts-infra

"This is an internal failure and not necessarily problematic"

UBR7200-5-USTSSNOTALIGNED

5-Notice

MAC-PHY TSS on [chars] U[dec] not at frame boundary MAC<T [hec] M [hec] F [hec]> start <T [hec] M [hec] F [chars]> current<T [hec]> tgc/frame [hec] mslot/frame [hec]

PHY TSS is not sampled at frame boundary

cmts-infra

"This is an internal failure and not necessarily problematic"

UBR7200-5-USPHY_BAD_INTR

5-Notice

USPHY with physical channel [dec] gets too many error interrupts

US PHY or MAC chips on the LC get into a bad state and SW can not recover it

ubr7200

"Collect show tech and then power cycle the Line card." "If problem does not recover contact Cisco for support"

UBR7200-4-CMTS_RF_POWER_ADJUST

4-Warning

rf-power adjusted to [dec] dBmV to meet upconvertor requirement.

This card has an upconvertor that has different limits on rf-power. rf-power has been adjusted to meet these limits.

ubr10000

"LOG_STD_NO_ACTION"

UBR7200-4-MCAST_ADMISSION_CONTROL_FAILURE

4-Warning

Multicast Service flow creation failed - group [chars] source [chars] host Interface [chars]

service flow creation failure due to admission control check.

cbr-application

"Adjust the min-rate parameter mentioned" " as part of the service class"

UBR7200-4-MCAST_DB_MAX_LIMIT_REACHED

4-Warning

Multicast DB full new entry not created - max [dec] group [chars] source [chars] fwd Interface [chars] bundle [chars]

Multicast explicit tracking DB entry creation failed due to max limit reached

cbr-application

"Reduce Static IGMP multicast config or wait for" "Dynamic IGMP OR PCMM multicast clients to leave"

UBR7200-4-MCAST_SID_MAX_LIMIT_REACHED

4-Warning

Multicast SID full new entry not created - max [dec] Bundle Interface [chars]

Multicast sid allocation failed due to max mcast sid limit reached

cbr-application

"Remove multicast qos or " "change single mqos to aggregate mqos"

UBR7200-6-MCAST_IPC_HEADER_ADD_FAILURE

6-Information

Multicast IPC header could not be added for source [chars] group [chars] fwd interface [chars]

Multicast IPC header could not be added

cbr-application

LOG_STD_ACTION

UBR7200-3-CMTS_RCC_CREATION_FAILURE

3-Error

RCC creation failure - ID [dec] host [chars]

RCC creation failed due to list insert failure.

cmts-docsis

LOG_STD_SH_TECH_ACTION

UBR7200-5-MACTSSLDERR

5-Notice

CMTS MAC TGC load pulse error sync-pulse interval [dec]

MAC FPGA TGC load pulse generation error

ubr7200

"Replace defective Line Card"

UBR7200-3-NULLIDBTTSVTBL

3-Error

A Null sw idb prevents pxf src-vfy tables from being updated MAC [enet] SID [dec]

A failure occurred in trying to update pxf src-vfy tables

ubr10000

"Copy the error message exactly as it appears and report it to your" "technical support representative."

UBR7200-3-NULLHWIDB

3-Error

A Null hwidb prevents the acl update for a modem's associated hosts MAC [enet] SID [dec]

A failure occurred in trying to update acl for a modem's associated host

ubr10000

LOG_STD_NO_ACTION

UBR7200-6-CPE_MOVED_FROM_WRONG_SID_CHAIN

6-Information

CPE [enet] was moved from SID Chain [dec] to [dec] from [chars] of the chain

The CMTS automatically corrected a condition where the CPE was in the wrong SID chain.

ubr7200

LOG_STD_NO_ACTION

UBR7200-4-DUPIPV6_SIDMISMATCH

4-Warning

Duplicate IPv6 Address %P in [chars] Sid [dec] MAC:[enet]. Dup Original Sid [dec]

Duplicate IPv6 Address found with different sid.

ubr7200

LOG_STD_NO_ACTION

UBR7200-5-WIDEBAND_AUTORESET

5-Notice

Reset total [dec] wideband capable cable modems which registered in

wideband autoreset feature reset wideband capable cable modems which registered in narrow band mode.

cmts-docsis

LOG_STD_NO_ACTION

UBR7200-3-ACFE_FAILURE

3-Error

[chars]

A failure occurred in ACFE algoirhtm module

cmts-qos

LOG_STD_ACTION

UBR7200-6-ACFE_NOTIFICATION

6-Information

[chars]

A special event happened in ACFE algorithm module

cmts-qos

LOG_STD_NO_ACTION

UBR7200-3-PA_REM_GENERAL

3-Error

[chars]

A general failure occured in the operation of the PA removal event state machine as defined by the failure string

ubr7200

LOG_STD_ACTION

UBR7200-3-PA_REM_ENQFAIL

3-Error

Enqueue of message failed slot [dec]

Enqueue of a PA removal message to an event queue failed

ubr7200

LOG_STD_ACTION

UBR7200-3-PA_REM_PCI_ERROR

3-Error

PCI error address = 0x[hec]\n

An unexpected PCI error happened

ubr7200

LOG_STD_ACTION

UBR7200-3-ENVM_FAN_OVERLOAD

3-Error

Fan Tray overloaded fail to support the linecard at slot [dec]

The cooling power provided by the routers's fans is lower than \n\ some LCs in chassis required.

-

"Replace the fan as soon as possible or the system may shut itself \n\ down or fail to operate properly."

UBR7200-4-ENVM_PS_OVERLOAD

4-Warning

Power supply may be overloaded to support the line card installed in slot [dec]

The power supply may be insufficient to support the number of line \n\ cards installed in the system under certain operation conditions \n\ like high temperature and high voltage margining.

-

"Upgrade the power supply as soon as possible or the system may \n\ fail to operation properly under some certain operation conditions."

UBR7200-6-DPON_CLC_GLOBAL

6-Information

Enabling DPON for MAC domain MD: [chars] implicitly enables DPON for all other

-

-

-

UBR7200-6-MQOS

6-Information

Power supply may be overloaded to support the line card installed in slot [dec]

The power supply may be insufficient to support the number of line \n\ cards installed in the system under certain operation conditions \n\ like high temperature and high voltage margining.

-

"Upgrade the power supply as soon as possible or the system may \n\ fail to operation properly under some certain operation conditions."

UBR7200-6-MD_DS_SG_DCID_CONFLICT

6-Information

Downstream channel IDs conflict in mac-domain of [chars]

At least two channels in the mac-domain have the same downstream channel ID. See show cable fiber-node to see channel ID assignments

-

"Change the downstream channel ID."

UBR7200-6-RF_CHAN_DCID_CONFLICT

6-Information

The downstream channel id's conflict for [chars] rf-channel [dec]\n could not be resolved by automatic DCID assignment.\n

Auto DCID assignment fails to assign valid DCID for a specific channel\n See \show cable fiber-node\ for detail channel ID assignments

-

"Check fiber node and downstream channel " "configuration."

UBR7200-6-CGD_AUTO_DCID_UNAVAILABLE

6-Information

Unable to assign an automatic channel ID for channel in the FN and MD for downstream [dec]/[dec]/[dec]:[dec] in FN [dec] \n

Unable to assign an automatic Channel ID for the newly added channel in the MAC Domain. See show cable fiber-node to see channel ID assignments in the Fiber-Node.

-

"Attempt to manually resolve channel ID conflict by disabling " "automatic DCID assignment."

UBR7200-6-CGD_AUTO_DCID_PARSE_ERROR

6-Information

Parse error during sync newly assigned automatic DCID \n\ while running CGD command.

A parse error has occured while trying to sync the newly assigned DCID to standby PRE.

ubr7200

"Remove and attempt to add the channel set again."

UBR7200-3-UNEXPECTED

3-Error

[chars]

The specified operation failed.

-

LOG_STD_NO_ACTION

UBR7200-6-CMTS_MD_IDX_OUT_OF_RANGE_ERROR

6-Information

Mac Domain Index [dec] is out of range.

Mac Domain Index is out of range.

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CMTS_SLOT_OUT_OF_RANGE_ERROR

6-Information

Slot [dec]/Subslot [dec]/MD [dec] is out of range.

Slot/subslot is out of range.

ubr7200

LOG_STD_NO_ACTION

CMTS-3-LIST_CREATE

3-Error

list create failed for list [chars]

The Cisco CMTS router is unable to create list due to insufficient system memory

cmts

"Run the show memory command to verify available system memory. " "If memory is full contact your Cisco technical support " "representative and provide the representative with the " "gathered information"

CMTS-3-LIST_ENQUEUE

3-Error

list enqueue failed for list [chars]

Unable to enqueue an entry to list

cmts

LOG_STD_ACTION

CMTS-3-LIST_INSERT

3-Error

list insert failed for list [chars]

The Cisco CMTS router is unable to insert an entry into list due to insufficient system memory or insert an exist entry

cmts

"Run the show memory command to verify available system memory. " "Then run the show logging command to view all system-logged " "messages. If memory is full contact your Cisco technical " "support representative and provide the representative with " "the gathered information"

UBR7200-7-PHY_CLK_MIS_DET_MSG

7-Debug

Clock misalignment detected on phy [dec]:\nIOS det count=[dec] bad DV count=[dec] total DV count=[dec] old cal data=0x%02x new cal data=0x%02x\n[chars]

A phy clock misalignment has been detected and corrected.

ubr10000

LOG_STD_NO_ACTION

CMTS-3-MCAST_SES_MISMATCH

3-Error

Session Request Response Mismatch for transaction ID [dec] session [chars][chars] CM [enet]

Response from the LC does not match the session requested for.

cmts

LOG_STD_ACTION

UBR7200-4-TLV56_CONFLICT_CHANNEL_SET

4-Warning

Confilct with TLV56 and channel set. Either remove TLV56 from the CM config file or adjust the power plant. CM Mac Addr <[enet]> may go offline due to high power.

Registration Failed Check TLV56 Configuration Setting\n

ubr7200

LOG_STD_NO_ACTION

UBR7200-6-CM_RNG_CLASS_ID_UNMATCH

6-Information

US that CM [enet] send Initial Rng Req has unmatched Channel Class ID0x[hec] with CM's Ranging Class ID0x[hec]\n

CM's Ranging Class ID doesn't match the the Channel Class ID of its upstream but it may be expected due to CM received a DCC/DBC... or CM config file included extended Ranging Class ID\n

ubr7200

LOG_STD_NO_ACTION

CMTS-4-RECONCL_CM_MISMATCH

4-Warning

Modem [enet] on Ca[dec]/0/[dec] mismatch during reconciliation delete reason: [chars]

After the LC switchover modem info will be synced to SUP to compare if there is any info mismatcheg: modem state service flow info etc. the modem will be deleted fully.

cmts

LOG_STD_ACTION

CMTS-4-RECONCL_CM_TIMEOUT

4-Warning

Reconciliation for slot [dec] timeout

Usually the reconciliation will end after all modem info being synced between SUP and LC. If we didn't get the end normally timer mechanism will take job and clean up left modem info

cmts

LOG_STD_ACTION

CMTS-4-RECONCL_CM_FINISH_CLC

4-Warning

Reconciliation [chars] for slot [dec] finished:

Reconciliation finished print counters.

cmts

LOG_STD_ACTION

CMTS-4-RECONCL_CM_FINISH_SUP

4-Warning

Reconciliation [chars] for slot [dec] finished:

Reconciliation finished print counters.

cmts

LOG_STD_ACTION

CMTS-4-RECONCL_RESET_D31_CM_FINISH

4-Warning

Reconciliation reset partial D31 CM for slot [dec] finished: D3.1 Online [dec] D3.1 DS partial [dec] D3.1 US partial [dec] D3.1 both partial [dec]. D3.0 DS partial [dec] D3.0 US partial [dec] D3.0 both partial [dec].

Reconciliation reset partial D31 CM finished print counters.

cmts

LOG_STD_ACTION

CMTS-4-UPSTREAM_SID_MISMATCH

4-Warning

Error populating upstream sid clusters CM[[enet]] docsis_prim_sid[[dec]] matches csc_sid[[dec]]

The secondary sid should never match the primary.

cmts

LOG_STD_ACTION

CMTS-4-DELETE_BONDING_MISMATCH

4-Warning

Error deleting upstream sid clusters CM[[enet]] docsis_prim_sid[[dec]] matches csc_sid[[dec]]

The secondary sid should never match the primary.

cmts

LOG_STD_ACTION

CMTS-3-DYN_SRV_IPC_SEND_FAILURE

3-Error

[chars]_Tx: nonblocked send failed dst_slot [dec]

Dynamic service failed to send nonblock IPC message

cbr-application

LOG_STD_NO_ACTION

CMTS-3-CABLE_IPC_SEND_FAILURE

3-Error

cable nonblocked ipc send failed msg_type[[dec]] dst_slot[[dec]]

Cable send nonblocked ipc failed

cbr-application

LOG_STD_NO_ACTION

CMTS-4-DS_RESIL_FAILURE

4-Warning

[chars]: [chars] failed

DS Resiliency ipc message processing failure.

cBR

"."

CMTS-4-ENQUEUE_SID_DUPLICATE

4-Warning

Error enqueing sid element Attempting to enqueue sid[[dec]] onto sid_reuse_queue that already exists

A duplicate sid should never exist in the free pool.

cmts

LOG_STD_ACTION

CMTS-4-ENQUEUE_SID_INVALID

4-Warning

Error enqueing sid element Attempting to enqueue invalid sid[[dec]] onto sid_reuse_queue

An invalid sid cannot be added to the free pool.

cmts

LOG_STD_ACTION

CMTS-4-CM_GET_RCC_FAILED_AFTER_LCHA

4-Warning

failed to get rcc after LCSO Attempting to get rcc[[dec]] cm[[enet]]

Find invalid rcc while cm recover

cmts

LOG_STD_ACTION

CMTS-3-INVALID_BW

3-Error

Invalid bandwidth configuration: cir_pct [dec] cir_sum [dec] eir_sum [dec]

Bandwidth configuration is invalid

cmts

LOG_STD_ACTION

CMTS-4-PKTCBL_GATE_RECON_DONE

4-Warning

Reconciliation [chars] for slot [dec] finished:

Reconciliation completed print counters.

packetcable

LOG_STD_ACTION

CMTS-3-PKTCBL_GATE_RECON_START

3-Error

Pktcbl reconciliation [chars] in progress:

Pktcbl Reconciliation started.

packetcable

LOG_STD_ACTION

CMTS-4-PKTCBL_GATE_RECON_MISMATCHED

4-Warning

Pktcbl reconciliation [chars] gate IE mismatched:

Pktcbl reconciliation gate IE mismatched.

packetcable

LOG_STD_ACTION

CMTS-4-PKTCBL_GATE_RECON_TIMEOUT

4-Warning

Pktcbl reconciliation for slot [dec] timeout

Usually the reconciliation will end after all gates' info being synced between SUP and LC. If we didn't get the end normally timer mechanism will take job and clean up left gates' info

packetcable

LOG_STD_ACTION

CMTS-6-PKTCBL_GATE_ERROR

6-Information

Pktcbl failure op. [dec] type: [[dec]] gate id: [[dec]] sub_id: [[chars]]

PacketCable encounters an error Details embedded in message ..

packetcable

LOG_STD_NO_ACTION

CMTS-4-PKTCBL_DB_ERROR

4-Warning

Pktcbl failure op. [dec] type: [[dec]] gate id: [[dec]] sub_id: [[chars]]

PacketCable database encounters an error Details embedded in message ..

packetcable

LOG_STD_NO_ACTION

UBR7200-3-OFDMA_IUC_CHANGE_ERR

3-Error

OFDMA IUC change error: cm [enet] [chars]

Changing OFDMA service flow IUC failed.

cbr-application

"LOG_STD_SH_TECH_ACTION"

CBRCCE-3-CBR_DP_FLOW_ADD_ERR

3-Error

Failed to add flow for CM [enet] sfid [dec] rc [dec]

Mostly caused by flow or cm_qos chunk exhausted

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_CFR_ADD_ERR

3-Error

Failed to add cfr for CM [enet] cfr id [dec] sfref [dec] sfid [dec] rc [dec]

Mostly caused by cfr chunk exhausted or cm_qos not found

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-4-CBR_DP_CFR_PARAM_CONFLICT

4-Warning

Classifier's parameters conflict: [chars]

Mostly caused by unsupported classifier's parameters combination

cbrcce-sw

"Please do not configure unsupported classifier's " "parameters or unsupported classifier's parameters combination " "as the error message indicated."

CBRCCE-3-CBR_DP_STA_QOS_ERR

3-Error

Failed to commit static qos for CM [enet] rc [dec]

Mostly caused by qos bind failure

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_DYN_QOS_ERR

3-Error

Failed to commit dynamic qos for CM [enet] sfid [dec] rc [dec]

Mostly caused by dynamic qos bind failure

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_JIB_HDR_SET_ERR

3-Error

Failed to set JIB header for CM [enet] sfid [dec] rc [dec]

Mostly caused by invalid service flow ID

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_FORW_INTF_SET_ERR

3-Error

Failed to set forwarding interface for CM [enet] sfid [dec] rc [dec]

Mostly caused by invalid service flow ID

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_QOS_PARAMS_SET_ERR

3-Error

Failed to set qos parameters for CM [chars] sfid [dec] rc [dec]

Mostly caused by invalid service flow ID

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_LOCK_ERR

3-Error

Failed to lock semaphore pid [dec]

Mostly caused by a process hogging CPU

cbrcce-sw

LOG_STD_SH_TECH_ACTION

CBRCCE-3-CBR_DP_TMP_DEL_ERR

3-Error

Failed to remove template from template_list for CM [enet]

Mostly caused by template remove failure

cbrcce-sw

LOG_STD_SH_TECH_ACTION

UNIXRP-3-IPCERR

3-Error

[chars] [dec]

IPC slot error

UNIXRP_DDTS_COMPONENT

LOG_STD_ACTION

UNIXRP-3-SEATERR

3-Error

[chars] [dec] [chars]

Failed to create IPC seat for line card

UNIXRP_DDTS_COMPONENT

LOG_STD_ACTION

UNIXRP-3-CARDERR

3-Error

[chars]

An IPC card has registered itself to the IPC master twice. The card\n\ malfunctioned and its IPC is not active.

UNIXRP_DDTS_COMPONENT

LOG_STD_ACTION

HA-6-TOOBIG

6-Information

Running config too big config sync failed

The running configuration was too big to be synced

UNIXRP_DDTS_COMPONENT

LOG_STD_NO_ACTION

HA-6-FALLBACK

6-Information

[chars] - configured mode[chars] fallback mode[chars]

This RP redundancy mode fell back to the indicated mode

UNIXRP_DDTS_COMPONENT

LOG_STD_NO_ACTION

HA-4-NOPROCESS

4-Warning

Creation of [chars] process failed

Creation of a platform high availability process failed.

UNIXRP_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

HA-6-MODE

6-Information

Operating RP redundancy mode is [chars]\n

Operational redundancy mode information

UNIXRP_DDTS_COMPONENT

LOG_STD_NO_ACTION

HA-6-STANDBY_READY

6-Information

Standby RP in slot [dec] is operational in [chars] mode\n

Indicates standby route processor readiness

UNIXRP_DDTS_COMPONENT

LOG_STD_NO_ACTION

HA-4-SYNC

4-Warning

[chars]

An error was encountered in a data sync operation

UNIXRP_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

HA-4-CHKPT

4-Warning

Platform CF - [chars]

Failure in some UNIX checkpointing activity.

UNIXRP_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

HA-4-CHKPTSEND

4-Warning

[chars] rc [dec] event [chars]

Failure to send UNIX checkpointing data.

UNIXRP_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

UNIX_BPD-3-HWIDB_ERR

3-Error

[chars]: [dec]

HWIDB Lookup Error

UNIX_BPD_DDTS_COMPONENT

LOG_STD_ACTION

UNIX_BPD-3-PKT_ERR

3-Error

[chars]: [chars]

Packet Not Available

UNIX_BPD_DDTS_COMPONENT

LOG_STD_ACTION

UNIX_IFUTIL-3-POOL_ERR

3-Error

[chars] Pool Creation Error for hwidb: [chars]

POOL Creation Error

UNIX_BPD_DDTS_COMPONENT

LOG_STD_ACTION

UNIX_IFUTIL-3-PAK_ERR

3-Error

Pak not available [chars]: [chars]

The running configuration was too big to be synced

UNIX_BPD_DDTS_COMPONENT

LOG_STD_NO_ACTION

UNIXLC_SPA-3-HWIDB_FAILURE

3-Error

Creation: port [dec] vc [dec]

Failed to create a hwidb.

diou

LOG_STD_SH_TECH_ACTION

UNIXLC_SPA-3-DEVICE_ERROR

3-Error

subSlot [dec] spatype 0x[hec]. Device error: [chars]

An error related to a device on the SPA is detected.

diou

LOG_STD_SH_TECH_ACTION

UNIXLC_SPA-3-ISR_RC_ERROR

3-Error

ISR return code out of range. rc=[dec]

The ISR error return code is out of range.

diou

LOG_STD_SH_TECH_ACTION

UNIXLC_SPA-4-SPABUS

4-Warning

Subslot [dec] [chars] SPA BUS access failed. timeout=[dec] err=[dec] par=[dec] err_c=0x[hec] addr=0x%08x data =0x[hec]

SPABUS has reported an error.

diou

LOG_STD_ACTION

UNIXLC_SPA-4-SPABUS2

4-Warning

Subslot [dec] SPA BUS access failed. No SPA present error

SPABUS has reported an error.

diou

LOG_STD_ACTION

UNIXLC_SPA-6-OIR

6-Information

Bay [dec] [chars] changed to [chars]

SPA OIR Sequence

diou

LOG_STD_NO_ACTION

UNIXLC_SPA-4-MAX_BANDWIDTH

4-Warning

Total SPA bandwidth exceeds line card capacity of %lu Mbps

The total bandwidth of SPAs exceeds the rated capacity of this line card.

diou

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

UNIXLC_SPA-4-MAX_BANDWIDTH_NS

4-Warning

Total SPA bandwidth exceeds line card capacity full utilization of installed SPA interfaces is not supported

The total bandwidth of SPAs exceeds the rated capacity of this line card.

diou

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

UNIXLC_SPA-3-POWER

3-Error

Bay [dec] 12V power is [chars]

SPA 12V power fault indicator

diou

LOG_STD_ACTION

UNIXLC_SPA-3-SPI4_INIT_FAILURE

3-Error

Bay [dec] initialization failure

Failed to create SPI4 subblock

diou

"Seach for resolved software issues using the Bug " "Toolkit at " "http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UNIXLC_SPA-3-NULL_SPA_BAY

3-Error

-

Pointer to object for bay [dec] is NULL.

diou

LOG_STD_SH_TECH_ACTION

UNIXLC_SPA-3-MESSAGE_ERROR

3-Error

Bay [dec]: [chars]

An unexpected error has occurred.

diou

"Seach for resolved software issues using the Bug " "Toolkit at " "http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UNIXLC_SPA-3-SPI4_CONFIG_FAILURE

3-Error

Bay [dec] spi4 configuration failure error [dec]

Failed to configure SPI4 interface

diou

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UNIXLC_SPA-3-SPA_CTRL_INIT_FAILURE

3-Error

Subslot [dec] spa controller initialisation failure error [dec]

Failed to initialise SPA controller

diou

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UNIXLC_SPA-3-SPA_CTRL_EFC_CONFIG_FAILURE

3-Error

Subslot spa controller EFC configuration failure error [dec]

Failed to configure SPA controller EFC

diou

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UNIXLC_SPA-3-FCI_NOT_SET

3-Error

Bay [dec] - FCI type not set

An FCI type of zero was detected

c7600-sip-common

LOG_STD_ACTION

UNIXLC_SPA-3-EFC_CHAN_ERR

3-Error

EFC error - interface [chars] vc [dec] anyphy [dec] err_code [dec] : [chars]

Failed to configure efc channel/parameters

diou

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UNIXLC_SPA-3-INVALID_ANYPHY

3-Error

Bay [dec] - Invalid anyphy number [dec] for vc [dec]

Interface has invalid anyphy mumber

spa-ser-common

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

UNIXLC_SPA-3-LINKREC_ERROR

3-Error

Link record error - Bay [dec] vc [dec] error code [dec]

Error processing link record structure

spa-ser-common

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

UNIXLC_SPA-3-SONET_CLOCK_FAILED

3-Error

SPA Sonet clock has failed status = 0x%08x

The SPA SONET clock has failed. SPAs that rely on the SPA SONET clock for proper operation such as POS and ATM will be affected.

c7600-sip-common

"If the SPA Sonet clock does not recover perform an " "OIR. "LOG_STD_RECUR_ACTION

UNIXLC_SPA-3-SONET_CLOCK_RECOVERED

3-Error

SPA Sonet clock has recovered status = 0x%08x

SPA Sonet clock has recovered

c7600-sip-common

LOG_STD_NO_ACTION

UNIXLC_SPA-3-INVALID_IF

3-Error

Attempted to access HWIDB for port [dec] on slot [dec] subSlot [dec]

The IOU attempted to access the HWIDB associated with\n\ a non-existent port.

diou

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UNIXLC_SPA-3-UNIXIPCALLOCFAIL

3-Error

Failed to allocate Common IPC buffer [chars]

The Carrier Card failed to allocate a buffer for\n\ communication with the Route Processor.

diou

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UNIXLC_SPA-3-CMDNOINT

3-Error

HWIDB Null for command [dec] port [hex]

The Route Processor passed down a port number that is unknown on the\n\ carrier card.

diou

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UNIXLC_SPA-3-EFC_FC_MAP_FAIL

3-Error

Failed to update EFC flow control identifier for interface [chars] status = [dec]

The SPA driver is not able to update the datapath EFC flow control identifier for the interface specified in the message. This indicates a hardware error.

diou

LOG_STD_NO_ACTION

UNIXLC_SPA-3-EFC_PROV_FAIL

3-Error

Failed to provision EFC for interface [chars] status = [dec]

The SPA driver is not able to provision EFC for the interface specified in the message. This indicates a hardware error.

diou

LOG_STD_NO_ACTION

UNIXLC_SPA-3-EFC_UNPROV_FAIL

3-Error

Failed to unprovision EFC for VC [chars] status = [dec]

The SPA driver is not able to unprovision EFC for the interface specified in the message. This indicates a hardware error.

diou

LOG_STD_NO_ACTION

UNIXLC_SPA-3-C2W_MAIN_INIT_FAIL

3-Error

Failed to initialize SPA main c2w bus for subslot [dec] status = [dec]

The SPA driver is not able to initialize SPA main c2w. This indicates a hardware error.

diou

LOG_STD_NO_ACTION

UNIXLC_SPA-3-NETCLK_FAIL

3-Error

Failed to [chars] SPA reference clock on [chars]

The SPA driver is not able to correctly configure the SPA reference clock on the specified interface. This indicates a hardware error.

diou

LOG_STD_NO_ACTION

UNIX_SPA-3-CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

Failed to create a SPA object.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-SPA_CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec].

Failed to create a SPA object.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-SPA_SB_CREATION_FAILURE

3-Error

Failed to create SPA SB

Failed to create a SPA subblock.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-NULL_HWIDB

3-Error

[chars] called with NULL hwidb

A NULL hwidb is encountered

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-NULL_VFT

3-Error

[chars] virtual function table is not initialized. spaType=0x[hec]

A required function table is not initialized

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-NULL_VFUNC

3-Error

[chars] vector is not initialized. spaType=0x[hec]

A required function vector is not initialized

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-MEM_ALLOC_ERROR

3-Error

[chars]

Memory allocation error.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-INVALID_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

Invalid slot number.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-INVALID_SLOTUNIT_NUM

3-Error

cardwide-port = [dec] max cardwide-port = [dec]

Invalid cardwide-port number.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-INVALID_INDX_RANGE

3-Error

index1= [dec] index2= [dec] maxIndex= [dec]

Invalid index range.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-INVALID_IF_INDEX

3-Error

index= [dec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec]

Index for the interface is not valid.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-INVALID_DATA_INSTANCE

3-Error

interface type [chars] slot [dec] port [dec] vc [dec] : [chars]

Data required to support the interface is not available.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-POWER_CYCLE

3-Error

[chars] occurred on Shared Port Adapter [dec]/[dec]

An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-DIAG_CONFIG

3-Error

[chars] did not complete [dec]/[dec]

An error has occured during diagnostic test.

c7600-field-diag

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-IPC_FAILURE

3-Error

IPC failure while [chars]

An error has occurred while prepareing or sending an IPC message.

diou

LOG_STD_SH_TECH_ACTION

UNIX_SPA-3-SENDCFGFAIL

3-Error

Failed to send configuration for [chars] to carrier-card for subslot=[dec]/[dec]

Sending configuration failed.

diou

LOG_STD_SH_TECH_ACTION

CRB_EVENT-3-CRB_RT_ERROR

3-Error

CRB Runtime Exception: [chars]

CRB Runtime Exception

-

LOG_STD_ACTION

UNIXRP_SPA-3-NO_HOST_INFO

3-Error

slot [dec] subSlot [dec] spaType 0x[hec]

Failed to get information about the host linecard.

diou

LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-3-MAX_SPA

3-Error

Power to IPSEC-SPA-2G in [chars] is denied because it has exceeded the number allowed[dec]

The number of IPSEC-SPA-2G in a chassis is limited. This message is displayed when the number of IPSEC-SPA-2G in the chassis has exceeded this limit.

diou

"Use only the number of supported IPSEC-SPA-2G"

UNIXRP_SPA-3-SPA_NO_HOST_INFO

3-Error

slot [dec] subSlot [dec] PID [chars]

Failed to get information about the host linecard.

diou

LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-3-HWIDB_FAILURE

3-Error

Creation: slot [dec] subSlot [dec] port [dec] vc [dec]

Failed to create an interface hwidb.

diou

LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-3-INVALID_PORT_NUM

3-Error

slot=[dec] port=[dec] hwidbType=0x[hec] max_port_num=[dec] LCtype=0x[hec]

The port number is out of range.

diou

LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-4-SPA_RESP_CMD_MISMATCH

4-Warning

[chars]: Expecting response to interface configuration command [dec] but received response to command [dec].

An internal synchronization error occurred while configuring the interface. The configuration may not have succeeded.

diou

"Check that the running configuration for the " "interface is correct. If this message occurred on the standby try " "reloading the standby to ensure that its configuration is in sync. " "If this message is repeatable please " LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-6-CARDRELOAD

6-Information

Module [dec] reload due to SPA insert in [dec]/[dec].

When inserting a SPA on this carrier card the card is reset.

-

LOG_STD_NO_ACTION

UNIXRP_SPA-4-SPA_CMD_NO_RESP

4-Warning

[chars]: No response for interface configuration command [dec]

A timeout occurred while RP was waiting for a response from line card. This may happen due to line card CPU being too busy to respond to the command.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The RP failed to allocate a buffer for communication with a SPA

diou

LOG_STD_ACTION

UNIXRP_SPA-3-DPIDX_LKUP_FAIL

3-Error

Failed to retrieve datapath identifier for interface [chars]

The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-FLOWID_ALLOC_FAIL

3-Error

Failed to allocate a flow control identifier for interface [chars]

The SPA driver is not able to allocate the datapath flow control identifier for the interface specified in the message. This indicates a software error.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-FLOWID_RELEASE_FAIL

3-Error

Failed to release a flow control identifier for interface [chars] status = [dec]

The SPA driver is not able to release the datapath flow control identifier for the interface specified in the message. This indicates a software error.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-VC_PROV_FAIL

3-Error

Failed to provision interface [chars]

The SPA driver is not able to provision the interface specified in the message. Verify that the SPA hardware is not provisioned above the supported limit. Otherwise this indicates a hardware error.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-CI_UPDATE_FAIL

3-Error

Failed to update connection identifier for interface [chars]

The SPA driver is not able to update the datapath connection identifier for the interface specified in the message. This indicates a software error.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-NULL_SPA_BAY

3-Error

-

Pointer to object for slot [dec] bay [dec] is NULL.

diou

LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-3-NULL_HWIDB_SPA_BAY_PORT

3-Error

HWIDB not found: slot [dec] bay [dec] port [dec]

A NULL hwidb is encountered

diou

LOG_STD_SH_TECH_ACTION

UNIXRP_SPA-3-NULL_DATA_STRUCTURE

3-Error

NULL

A SPA driver is not able to retrieve the data structure mentioned in the message. This indicates a software error.

diou

LOG_STD_NO_ACTION

UNIXRP_SPA-3-HWIDB_INIT_FAIL

3-Error

Failed to initialize data structure for SPA port [dec]/[dec]/[dec]

A SPA driver was not able to properly initialize a data structure mentioned in the message. This indicates a software error.

diou

LOG_STD_NO_ACTION

PLATFORM_INFRA-5-IOS_INTR_OVER_LIMIT

5-Notice

IOS thread disabled interrupt for Total: [dec] msec utime: [dec] msec stime: [dec] msec.

IOS thread process disabled interrupt too long

Respective Platform Component

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_OVER_LIMIT_HIGH_STIME

5-Notice

IOS thread blocked due to SYSTEM LEVEL ISSUE for Total: [dec] msec utime: [dec] msec stime: [dec] msec. [chars]

IOS thread needs to disable interrupt to protect its critical section of the code. But when it locks up the interrupt for too long due to SYSTEM LEVEL ISSUE causing high stime display interrupt over limit warning traceback

Respective Platform Component

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_OVER_LIMIT_LEGACY

5-Notice

IOS thread disabled interrupt for [dec] msec.

IOS thread process disabled interrupt too long for platforms not supporting syspage

Respective Platform Component

LOG_STD_ACTION

PLATFORM_INFRA-5- IOS_INTR_LIMIT_NOT_SET

5-Notice

IOS thread interrupt limit not set

IOS failed to retrieve interrupt limit

iosxe-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_EVENT

5-Notice

IOS thread interrupt event [dec].

IOS thread process interrupt event

asr1k-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_HISTORY

5-Notice

[[dec]|[dec]] [[dec]:[dec]] [[dec]->[dec]] ra[ l* 0x[hec] l* 0x[hec] ]

IOS thread process interrupt history

asr1k-iosd-infra

LOG_STD_ACTION

PLATFORM_INFRA-5-IOS_INTR_INVALID_LEVEL

5-Notice

IOS thread interrupt level [dec] replaced by [dec]

An invalid IOS thread interrupt level was used

asr1k-iosd-infra

LOG_STD_ACTION

L2TM-3-ACCESS_ERR

3-Error

Tcam access failed while [chars]

Failed to read/write from/to tcam.

hardware

LOG_STD_ACTION

L2TM-7-INTERNAL_ERR

7-Debug

Internal error: [chars]

An internal error occured.

firmware

LOG_STD_ACTION

DHCP_SNOOPING_CAT3550-3-MVR_INSTALL

3-Error

Cannot install [chars] ACLs for DHCP Snooping probably no TCAM space

When DHCP Snooping is enabled ACLs need to be installed into the TCAM. This will fail if there is insufficient space in the TCAM.

firmware

"Reduce the number of input and/or output" "PACLs and/or VACLs to make space in the TCAM."

DHCP_SNOOPING_CAT3550-3-UNEXPECTED_EVENT

3-Error

Process received unknown event major [hec] minor [hec].

-

-

-

DOT1Q_TUNNELLING-4-MTU_WARNING

4-Warning

\nSystem MTU of [dec] might be insufficient for 802.1Q tunnelling.\n 802.1Q tunnelling requires system MTU size of [dec] to handle maximum size ethernet frames.\n\n

With 802.1Q tunnelling the system MTU setting needs to take into account the four byte overhead associated with the additional 802.1Q tag.

firmware

"Issue the <CmdBold>system mtu<noCmdBold> " "global configuration command to adjust system MTU to take into " "account the additional 802.1Q tag."

QATM-2-ASDATA_READ

2-Critical

Cannot read TCAM associated data

Possibly bad hardware

hardware

LOG_STD_ACTION

QATM-2-TCAM_READ

2-Critical

Cannot read TCAM

Possibly bad hardware

hardware

LOG_STD_ACTION

QATM-2-ASDATA_WRITE

2-Critical

Cannot write TCAM associated data

Possibly bad hardware

hardware

LOG_STD_ACTION

QATM-2-TCAM_WRITE

2-Critical

Cannot write the TCAM

Possibly bad hardware

hardware

LOG_STD_ACTION

FM-1-INIT

1-Alert

Feature Manager subsystem initialization failure

The Feature Manager subsystem failed to initialize. Most likely cause is insufficient memory at init time. Probably either the hardware has failed or this image is being run on a platform it was not intended for.

firmware

"Replace failing hardware or obtain the correct " "IOS image for this platform whichever is " "appropriate."

FM-7-TRANSDEF

7-Debug

No augmentation function found for VMR

An Internal Error occured. An Access Control List was not interpretted correctly. The Value-Mask Result is incorrect.

firmware

LOG_STD_ACTION

FM-3-TOSCOST

3-Error

Minimize monetary cost TOS bit unsupported in hardware ignored

This hardware platform supports filtering based on DSCP rather than TOS and precedence. The DSCP field does not include the minimize monetary cost bit from the TOS field so hardware will ignore this bit when checking for a match to an ACE. This can lead to unintended filtering actions.

firmware

"Design filters that do not test for minimum " "monetary cost TOS."

FM-2-NOVMR

2-Critical

Cannot create VMR data structures for access list [chars]

The Feature Manager could not allocate the data structures needed to describe an ACL in a form that can be loaded into hardware. Probably caused by lack of available memory.

firmware

"Use a less complicated configuration that " "requires less memory."

FM-2-NOMAP

2-Critical

Cannot create Feature Manager data structures for VLAN Map [chars]

The Feature Manager could not allocate the data structures needed to describe a VLAN Map in a form that can be loaded into hardware. Probably caused by lack of free memory.

firmware

LOG_STD_REDUCE_ACTION

FM-2-NOSB

2-Critical

Cannot create subblock for interface [chars]

The Feature Manager was unable to save per-interface information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly.

firmware

"Use a less complicated configuration that " "requires less memory."

FM-2-NOVLB

2-Critical

Cannot create memory block for VLAN [dec]

The Feature Manager was unable to save per-VLAN information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly.

firmware

"Use a less complicated configuration that " "requires less memory."

FM-3-NOLABEL

3-Error

Cannot allocate [chars] label for interface [chars]

The Feature Manager was unable to allocate a label for the features on this interface. This means that the hardware cannot be programmed to implement the features and packets for this interface will be filtered in software. There is a limit of 256 labels per direction.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible."

FM-3-NOLABELVL

3-Error

Cannot allocate [chars] label for VLAN [dec]

The Feature Manager was unable to allocate a label for the features on this VLAN. This means that the hardware cannot be programmed to implement the features and packets on this VLAN will be filtered in softtware. There is a limit of 256 labels per direction.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same VLAN Maps on multiple " "VLANs if possible."

FM-3-UNLOADING

3-Error

Unloading [chars] label [dec] feature from [chars]

The Feature Manager was unable to fit the complete configuration into the hardware so some features will have to be applied in software. This prevents some or all of the packets from being forwarded in hardware and requires them to be forwarded by the CPU. Multicast packets may be dropped entirely instead of being forwarded.

firmware

"Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible."

FM-3-RELOADED

3-Error

Reloading [chars] label [dec] feature in [chars]

The Feature Manager was able to fit more of the configured features on this label into the hardware. One or more features had previously been unloaded because of lack of space.

-

LOG_STD_NO_ACTION

FM-3-MERGEFAIL

3-Error

[chars] ACL merge error [dec] [chars] on [chars] label [dec]

The Feature Manager was unable to complete the merge of the configured features into a form suitable for loading into the hardware. Packets potentially affected by this feature will be sent to the CPU for processing instead. The most likely cause is specifying an ACL that is too large or too complex for the system to handle.

firmware

"Try specifying a smaller and less complicated " "configuration."

FM-3-GOTLABEL

3-Error

Got label for [chars]

The Feature Manager has now been able to allocate a hardware label for the interface. The interface had needed a label before but none was available.

-

LOG_STD_NO_ACTION

FM-3-GOTVLABEL

3-Error

Got label for VLAN #[dec]

The Feature Manager has now been able to allocate a hardware label for the VLAN. The VLAN had needed a label before but none was available.

-

LOG_STD_NO_ACTION

FM-3-INSERTFAIL

3-Error

Insert of access-map [chars] #[dec] into [chars] label [dec] failed

The system ran out of CPU memory when trying to merge sections of an access map.

firmware

"Reduce other system activity to ease the memory demands. For example " "remove any ACLs that have been defined but are not now used. Use " "simpler ACLs with fewer access control entries ACEs. Use fewer "

FM-3-AUGMENTFAIL

3-Error

Augmenting of access-map [chars] on [chars] label [dec] failed

The system ran out of CPU memory when attempting to merge internally required elements with the configured access maps.

firmware

LOG_STD_REDUCE_ACTION

FM-3-INITLABEL

3-Error

Special initialization of label [dec] failed

Initialization of the access list hardware failed. Prioritization of routing protocol packets above other kinds of packets may not occur on some VLANs or routed ports.

firmware

LOG_STD_ACTION

FM-3-OUTTTABLE

3-Error

Not in truth table: RACL [dec] VLMAP [dec]

An unrecoverable software error occurred while trying to merge the configured output features.

firmware

"show running-config"

FM-3-INTTABLE

3-Error

Not in truth table: VLMAP [dec] RACL [dec] Rtprot [dec] Redir [dec] Mcb [dec] Feat [dec]

An unrecoverable software error occurred while trying to merge the configured input features.

firmware

"show running-config"

FM-3-QOSTTABLE

3-Error

Not in truth table: ACL [dec] in map action [dec]

A software error occurred while trying to merge a QoS Policy Map

firmware

"show running-config"

FM-3-MAXRECURSION

3-Error

Too many [dec] levels of recursion while merging [chars] code [dec].

The configuration is too complicated for the platform specific ACL merge code to support. Most likely cause is including too many separate access lists in a single VLAN map or policy map.

-

"Reduce the number IP or MAC access lists" " considered separately in any one VLAN or policy"

FM-3-LABELERROR

3-Error

Incorrect label to [chars] vlan label attribute copy callback srclabel [dec] dstlabel [dec]

The Feature Manager attribute copy callback was called with an incorrect source or destination label.

firmware

"show running-config"

FM-3-NOTEMPTY

3-Error

Illegal copy of attribute to non empty [chars] vlan label [dec]

The Feature Manager attribute copy callback was called with a destination label already being used by a VLAN or routed port.

firmware

"show running-config"

FM-3-ILLEGALCOPY

3-Error

Illegal copy of [chars] access group [chars] from [chars] label [dec] to [dec]

An internal software error has occurred

firmware

"show running-config"

FM-3-CONFLICT

3-Error

[chars] [chars] conflicts with [chars]

Port access lists PACLs may not be applied when input router access lists or VLAN maps have been applied and vice versa

firmware

"Remove the conflicting feature or features"

FM-3-WRONGLABEL

3-Error

Inconsistent records of label for [chars]: FM has [dec] LM has [dec]

An internal software error has occurred.

firmware

"show running-config"

FM-3-NOTOBJECT

3-Error

Invalid object VLAN [dec] IDB [hec] used in Feature Manager operation

An internal software error has occurred

firmware

"show running-config"

FM-4-EXCESSSECONDARY

4-Warning

More than [dec] secondary IP addresses configured on interface [chars]

When secondary IP addresses are configured on an interface the hardware is usually programmed so that the ICMP redirect functionality on the CPU is not notified of packets sent between two subnets configured on the same interface. If many secondary IP addresses are configured on the same interface it becomes impractical to program the hardware in this manner this message is logged and the CPU will be notified of every packet sent between two subnets on this interface. No ICMP redirects will be sent in error but the CPU usage may increase because of the additional notifications. The user may wish to configure \no ip redirects\ on the interface to reduce the CPU load on the system.

firmware

"configure the \"no ip redirects\" command on " "this interface"

FM-3-UNKNOWNACTION

3-Error

Unknown VMR access group action 0x[hec]

An internal software error has occurred.

firmware

LOG_STD_ACTION

NETWORK_PORT_SATELLITE-6-MAC_LOCKUP

6-Information

Transmit lock up is detected in [chars]. This port is adminstratively down.

When the PHY is powered on and off the MAC cycles from Gigabit to 100 and the port might lock up and stop sending packets. The PHY refers to the physical layer device on the switch which sends and receives optical signals and provides framing and line integrity.

hardware

"Shut down the port by using the shutdown interface configuration " "command and bring it back up by using the no shutdown interface " "configuration command"

NETWORK_PORT_SATELLITE-3-PHY_LOCKUP

3-Error

Repeated phy lockup seen on [chars]. Interface will be shut down.

Phy lockup was detected too many times in a row. Interface is shutdown to avoid continuous link flapping.

firmware

"To re-enable interface issue 'shutdown' followed " "by 'no shutdown' command in interface " "configuration mode."

CPU_NET-0-QUEUE_STUCK

0-Emergency

The interface between the CPU and the switch has\n become stuck. The switch must now reset to clear this condition\n. Retrieval queue [dec].\n

The CPU can no longer communicate with the network.

-

"Reload the system."

GIGASTACK-3-INIT_FAILURE

3-Error

Gigastack GBIC in [chars] initialization failed.

Gigastack GBIC failed POST.

firmware

"Remove the Gigastack GBIC and re-insert it into the GBIC slot."

GIGASTACK-6-LOOP_DETECTED

6-Information

Gigastack GBIC in [chars] is selected as Master Loop Breaker. \nLink 2 of the Gigastack GBIC is disabled to break the loop.

Loop is detected in the Gigastack and this Gigastack GBIC is selected as the Master Loop Breaker. Link 2 of this Gigastack GBIC is disabled to break the loop.

-

LOG_STD_NO_ACTION

GIGASTACK-6-LOOP_BROKEN

6-Information

Link loss is detected in the Gigastack loop \nLink 2 of the Gigastack GBIC in [chars] is re-enabled.

Loop formed by Gigastack modules is broken because of link loss. Link 2 of the Master Loop Breaker is re-enabled to replace the broken link

-

LOG_STD_NO_ACTION

GIGASTACK-1-NO_LOOP_DETECT

1-Alert

The link neighbor of link [dec] of Gigastack GBIC in [chars] did not respond to the loop detection request. If loop topology is deployed make sure all switches in the stack are running the latest software.\n

No acknowledgement for Gigastack loop detection request is received from one of the links on a Gigastack GBIC. Either the neighboring switch does not support Gigastack Loop breaking algorithm or the link between the two Gigastack GBICs is broken. Under this condition a Gigastack loop topology will not be automatically detected and the connectivity between switches in the stack could be lost.

-

"If loop topology is used in the Gigastack make sure the latest software is running on all switches in the stack. Check the Gigastack GBICs involved to make sure they are functioning."

QM-4-NOT_SUPPORTED

4-Warning

Action '[chars]' is not supported for a policymap attached to output side.

This message means that a set or trust policy-map class configuration command was configured in a policy map and attached to an egress interface. A warning message is logged and the actions do not take affect. This is a hardware limitation.

hardware

"Do not configure a set or trust policy-map class configuration command in a " "policy map and attach it to an egress interface. These policy-map actions " "are supported only on ingress interfaces."

QM-4-ACTION_NOT_SUPPORTED

4-Warning

Action is not supported in policymap [chars]

This message means that an action other than the set trust and police policy-map class configuration commands was configured in a policy map. This is a hardware limitation.

hardware

"Configure only the supported actions of set trust and police when in " "policy-map class configuration mode."

QM-4-MATCH_NOT_SUPPORTED

4-Warning

Match type is not supported in classmap [chars]

match ACL match ip dscp and match ip precedence are the match types that are supported

firmware

-

QM-4-CLASS_NOT_SUPPORTED

4-Warning

Classification is not supported in classmap [chars]

This message means the an unsupported match class-map configuration command was configured in a policy map and attached to an egress interface or that more than one match command was configured. This is a hardware limitation.

hardware

"Reconfigure the class map or the policy map. Use only the match ip dscp dscp-list " "class-map configuration command in a policy map that is attached to an egress " "interface. Only one match per class map is supported."

QM-4-HARDWARE_NOT_SUPPORTED

4-Warning

Hardware limitation has reached for policymap [chars]

The policy map configuration has exceeded the limitation of the hardware. You configured more QoS ACL entries than the number specified in the Switch Database Management sdm template.

hardware

"Reconfigure the class map or the policy map and reduce the number of QoS ACLs."

QM-4-POLICER_NOT_SUPPORTED

4-Warning

Number of policers has exceeded hardware limitation for policymap [chars]

The policy map configuration has exceeded the limitation of the hardware. You configured more policers in a policy map by using the police or police aggregate policy-map class configuration command

hardware

"Reconfigure the class map or the policy map and reduce the number of policers."

QM-4-POLICING_RATE_NOT_SUPPORTED

4-Warning

Policer configuration has exceeded hardware limitation for policymap [chars]

The policy map configuration has exceeded the limitation of the hardware. You configured a larger policing rate or burst size in a policy map by using the police or police aggregate policy-map class configuration command than supported.

hardware

"Reconfigure the class map or the policy map and reduce the policing rate or " "burst size."

QM-4-UNEXPECTED_INTERNAL_QOS_CONDITION

4-Warning

Unexpected internal QoS condition.

This message means that an unexpected internal QoS condition has occurred. QoS debug may be enabled to obtain more information in case the condition recurs.

firmware

LOG_STD_ACTION

L3TCAM-3-SIZE_CONFLICT

3-Error

[chars] requires enabling extended routing

In order to support this feature TCAM entry needs to be configured to extended routing enable.

firmware

"Modify the Switch Database Management SDM " "template to enable the switch to support the " "144-bit Layer 3 TCAM. Use the sdm prefer " "extended-match sdm prefer access extended-match " "or sdm prefer routing extended-match global " "configuration command and then reload the switch " "by using the reload privileged EXEC command."

L3TCAM-3-TOO_MANY_VRF

3-Error

Exceed the maximum number of VRF allowed

The number of VPN exceeds the maximum number of allowed VPN routing/forwarding table on this hardware platform.

firmware

"Reconfigure your switch to limit the number " "of VRFs. Do not define name more than seven "

PBR-2-NO_RMAP

2-Critical

Cannot create PBR data structures for route-map [chars]

The PBR manager could not allocate the data structures needed to describe a route-map being used for policy routing. Probably caused by lack of available memory.

firmware

"Use a less complicated configuration that " "requires less memory."

PBR-3-NO_LABEL

3-Error

Cannot allocate label for route-map [chars]

The PBR manager could not allocate a label for this route-map. This means that the hardware cannot be programmed to implement policy routing. There is a limit of 247 labels for policy routing

firmware

"Use a less complicated configuration that " "allows label sharing. Use the same route-maps on multiple interfaces if possible"

PBR-3-MERGE_FAIL

3-Error

[chars] ACL merge error [dec] on route-map [chars]

The PBR manager could not complete the merge of the configured route-map into a form suitable for loading into the hardware. The most likely cause is specifying an ACL that is too large or too complex for the system to handle.

firmware

"Try specifying a smaller and less complicated " "configuration."

PBR-3-UNSUPPORTED_RMAP

3-Error

Route-map [chars] not supported for Policy-Based Routing

The route-map attached to an interface for policy routing contains an action that is not supported on this platform. This is a hardware limitation.

hardware

"Reconfigure the route-map. Use only 'permit' " "entries and 'set ip next-hop' action in the " "route-map."

PBR-4-CPU_SUPPORTED_ACTION

4-Warning

Set action in sequence [dec] of route-map [chars] supported by forwarding to CPU

The route-map attached to an interface for policy routing contains an action that is not supported in hardware since it contains a 'set interface' 'set ip default next-hop' 'set default interface' or or 'set ip df' actions. This requires the packets to be forwarded by the CPU.

firmware

"Reconfigure the route-map. Use only 'set ip " "next-hop' in the route-map if possible."

PBR-3-INSTALL_FAIL

3-Error

Policy route-map [chars] not installed in hardware

The PBR manager was unable to install the complete route-map in the hardware so this will have to be applied in software. This requires the packets to be forwarded by the CPU.

firmware

"Reconfigure the route-map to use a simpler " " configuration. Use the same route-map on " "multiple interfaces if possible"

PBR-4-RETRY_INSTALL

4-Warning

Route-map [chars] installed in hardware upon retry

The PBR manager was able to fit the complete configuration into the hardware. One or more route-maps had previously not been loaded because of lack of space.

firmware

LOG_STD_NO_ACTION

GBIC-6-SERDES_SERIAL_INV_DATA

6-Information

Unrecognizable GBIC found in [chars] serial data 0x%02x

The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC.

firmware

"If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch."

GBIC-6-SERDES_MODULE_UNKNOWN

6-Information

Unrecognizable GBIC found in [chars] module mask 0x%02x

The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC.

firmware

"If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch."

GBIC-4-NOREAD_VSDATA

4-Warning

Unable to read vendor-specific data for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read identifying vendor-specific information to verify its authenticity.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

GBIC-4-UNRECOGNIZED_EXTTYPE

4-Warning

GBIC interface [chars] has unrecognized extended type

The GBIC was identified as a Cisco GBIC but the system does not recognize its reported extended type code.

firmware

"Check the list of supported GBICs for this version " "of the system software. An upgrade may be required " "for newer GBICs. Even if unrecognized the GBIC " "may still operate properly perhaps with limited " "functionality."

GBIC-4-NOREAD_VNAME

4-Warning

Unable to read vendor name for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read the name of the GBIC's vendor.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

GBIC-4-NOREAD_VSERNUM

4-Warning

Unable to read serial number for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read the GBIC's serial number.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

GBIC-4-XCVR_INTERR

4-Warning

Internal error occurred in setup for GBIC interface [chars]

The system could not allocate resources or had some other problem in the setup for the specified GBIC interface.

firmware

"Reload the system. If the problem persists " "contact TAC."

GBIC-4-CHECK_SUM_FAILED

4-Warning

GBIC EEPROM data check sum failed for GBIC interface [chars]

The GBIC was identified as a Cisco GBIC but the system was unable to read vendor-data information to verify its correctness.

firmware

"Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective."

ETHCNTR-3-INTERNAL_ERROR

3-Error

Internal Error [chars]

An internal error occurred.

firmware

LOG_STD_RECUR_ACTION

ETHCNTR-3-UNEXPECTED_EVENT

3-Error

Request 0x%08x encountered event [dec] in state [dec]

An unexpected event occurred for a ram access request.

firmware

LOG_STD_RECUR_ACTION

ETHCNTR-3-FLOWCONTROL_DUPLEX_ERROR

3-Error

Flowcontrol will not take effect until duplex is set to auto.

-

firmware

"Configure duplex auto"

ETHCNTR-3-RA_REPLY_ERROR

3-Error

Invalid reply to RAM Access [chars] request 0x%08x from satellite [dec]

A request to read/write RAM on satellite access produced unexpected reply.

firmware

LOG_STD_RECUR_ACTION

ETHCNTR-3-RA_ALLOC_ERROR

3-Error

RAM Access [chars] [chars] memory allocation failure

A request to read/write RAM failed memory allocation

firmware

LOG_STD_RECUR_ACTION

ETHCNTR-7-RAM_ACCESS_CMD_GROWING

7-Debug

Ethernet Controller: Growing RAM Access [chars] Command

The command buffer for RAM Access is being grown dynamically because the original buffer was not big enough

firmware

LOG_STD_RECUR_ACTION

ETHCNTR-3-LOOP_BACK_DETECTED

3-Error

Keepalive packet loop-back detected on [chars].

Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network.

firmware

"Correct the problem causing the loopback condition. Then " "bring the port up by entering the shutdown then no shutdown " "interface configuration commands. The port will be " "automatically restarted after a timeout if errdisable " "recovery cause loopback is configured."

ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD

3-Error

Half-duplex loopback detected collision threshold exceeded on [chars].

The collisions on a half-duplex port exceeded the threshold with no valid data packets. The port is considered to be in a loopback condition. This may be caused by accidentally plugging a balun cable into the port

firmware

"Correct the problem causing the loopback condition. Then " "bring the port up by entering the shutdown then no shutdown " "interface configuration commands. The port will be " "automatically restarted after a timeout if errdisable " "recovery cause loopback is configured."

ETHCNTR-3-INVALIDMAP

3-Error

Invalid map [dec] for address [enet]

An attempt to bridge a packet in software obtained an invalid result.

firmware

LOG_STD_RECUR_ACTION

ETHCNTR-3-MOLSENDINT

3-Error

Molecule send from interrupt handler

An interrupt handler is accessing the hardware in a manner that is not permissible in an interrupt handler.

firmware

LOG_STD_ACTION

ETHCNTR-2-MOLSENDTIMEOUT

2-Critical

Molecule send timeout queue [dec] molecule 0x[hec] 0x[hec]

An attempt to read or write one or more of the hardware settings failed.

firmware

LOG_STD_ACTION

PLATFORM_CATALYST2955-3-PORT_NOT_OPERATING

3-Error

[chars] [chars] [chars] [chars]

The port is not operating the startup selftest has failed

-

LOG_STD_ACTION

SRP-4-RAC_ALARM

4-Warning

[chars] Side [chars] [chars]

A physical error condition detected at the indicated RAC

srp

"Diagnose and repair the physical error"

SRP-4-ALARM

4-Warning

[chars] Side [chars] [chars]

A physical line error condition exists on the indicated network

srp

"Diagnose and repair the physical error"

SRP-3-NULL_P_ALARM

3-Error

Dereferencing NULL pointer [chars] in [chars]

NULL pointer error condition exists. Some features/commands may not work properly

srp

"Please Contact Cisco Systems TAC support"

SRP-3-FALSE_VAL_ALARM

3-Error

[chars] - error in [chars]

FALSE value returned. Some features/commands may not work properly

srp

"Please Contact Cisco Systems TAC support"

SRP-3-DUP_MAC_ADDR

3-Error

[chars] : Duplicate mac addresses in topology

The topology contains 1 or more duplicate mac addresses

-

"Identify duplicate address and correct configuration."

SRP-3-SINGLE_NODE_TOPO

3-Error

[chars] : Single node in topology

The topology discovery resulted in a single node being found

-

"This can be due to duplicated mac addresses." "\nIdentify mac address of interface and ensure it is not" "\nduplicated on other nodes." "\nIf the node is in loopback disregard this message."

SRP-3-RING_ID_ERROR

3-Error

[chars] : Rx side [chars] Tx side of fiber originates on side [chars]

The fiber on the specified side is remotely connected \nto the wrong side

-

"Verify that each side A is connected to side B" "\nand each side B is connected to side A."

SRP-4-WRAP_STATE_CHANGE

4-Warning

[chars] [chars] on side [chars] [chars]

The specified side of the interface is wrapped or unwrapped.

-

"Diagnose the cause of the wrap."

SRP-4-SRR_STATE_CHANGE

4-Warning

[chars] SRR usage changed [chars]

SRR ring usage is changed using Inner Outer or Both rings.

-

"Diagnose the cause of the ring usage change."

SRP-4-SRR_VER_MISSMATCH

4-Warning

[chars] SRR version missmatch detected.

Different SRR version received from other nodes.

-

"Update the IOS image on all nodes of the ring to the same SRR version"

SRP-1-WRAPPING_PROCESS_LOCKED

1-Alert

[chars] The wrap/unwrap state-change process is locked

A wrap/unwrap state change process has not come to an end on time.

-

"If message is periodic issue a \"shut\" and \"no shut\" on the interface."

SRPMIB-3-NULL_P_ALARM

3-Error

Dereferencing NULL pointer [chars] in [chars]

NULL pointer error condition exists. Some feature/command may not work properly

srpmib

"Please Contact Cisco Systems TAC support"

SRPMIB-3-FALSE_VAL_ALARM

3-Error

[chars] - error in [chars]

FALSE value returned. Some features/commands may not work properly

srpmib

"Please Contact Cisco Systems TAC support"

QLLC-3-NOMEM

3-Error

Not enough memory available

There is not enough memory in the system to complete this request.

-

"Add more memory to the router. Otherwise reduce the configuration or\n\ the load on the router."

QLLC-3-NOLLC2

3-Error

Unable to open an llc2 session

An LLC2 session could not be established with the destination MAC\n\ address.

-

"Verify that the qllc partner statement in the configuration file is\n\ correct and that the partner is on the desired LAN."

QLLC-3-NULLPTR

3-Error

[chars] ptr is null

The specified structure was not configured.

-

"Confirm the configuration commands for the structure."

QLLC-4-NOQLLC

4-Warning

Unable to open qllc session current state is [chars]

A QLLC session could not be established.

-

"Verify that the qllc partner and the qllc xid commands are correct."

QLLC-3-DIFFPRTR

3-Error

[enet] - Different partner - originally [enet] - now [enet]

The partner for this QLLC virtual MAC address does not match the MAC\n\ address that was defined with the qllc partner command.

-

"Verify that the qllc partner statement in the configuration file is\n\ correct."

QLLC-3-NONULLXID

3-Error

Couldn't make null xid - [enet] -[enet]

An attempt to create an IEEE XID failed.

-

"Verify that the qllc partner statement in the configuration file is\n\ correct and that the partner is on the desired LAN."

QLLC-3-NOXID2

3-Error

Couldn't make xid - [enet] -[enet]

The QLLC XID could not be forwarded to the LAN.

-

"Verify that the qllc partner and the qllc xid commands are correct."

QLLC-3-BADSTATE

3-Error

Bad qllc state - [chars] - [enet]

An invalid LLC primitive was detected.

-

"Verify that the Token Ring ports and any participating LAN devices are\n\ configured correctly."

QLLC-3-NOMACADDR

3-Error

No lnx entry for macaddr [enet]

No virtual MAC address was defined for this interface.

-

"Define the virtual MAC address using either the x25 map qllc or the\n\ x25 pvc qllc command."

QLLC-3-BADOPCODE

3-Error

Opcode [chars] is invalid

Either remote source-route bridging or local acknowledgment is\n\ configured incorrectly.

-

"Verify that remote source-route bridging and local acknowledgment are\n\ configured correctly."

QLLC-3-IFRAME

3-Error

[chars]

An I-Frame was discarded due to network congestion.

-

"Verify that the LAN is not beaconing and that it is not in a congested\n\ state. Copy the error message exactly as it appears and report it to\n\ your technical support representative."

QLLC-3-BADSTATEEVENT

3-Error

Bad qllc state - [chars] event - [chars] macaddr - [enet]

The LLC primitive specified placed the router in an invalid state.

-

"Verify that the Token Ring ports and any participating LAN devices are\n\ configured correctly."

QLLC-3-NOPAKENQ

3-Error

Pak enqueue failed

A packet was not sent to the LAN.

-

"Verify that the LAN partner is configured correctly and that the\n\ partner is on the desired LAN."

QLLC-3-BADRSRBOPCODE

3-Error

Bad opcode %04x from [enet] to [enet]

Either remote source-route bridging is incorrectly configured or the\n\ other RSRB device is down.

-

"Verify that remote source-route bridging is configured correctly with\n\ the right version of the IOS software."

QLLC-3-LNXNOTFOUND

3-Error

lnx_remove_macaddr_hash did not find target lnx

The qllc srb command was not defined for this interface.

-

"Add a valid qllc srb statement for this serial interface."

QLLC-3-BADQLLCSTATE

3-Error

Bad qllc state - [chars]

An invalid QLLC primitive was detected.

-

"Verify that the partner QLLC device is configured correctly."

QLLC-3-GENERRMSG

3-Error

[chars]

The text string provided with this error message describes the\n\ specific QLLC problem.

-

"Follow the instructions that appear with the error message. Copy the\n\ error message exactly as it appears and report it to your technical\n\ support representative."

QLLC-3-BAD_XID

3-Error

Sna configuration error for [enet]: Lan device is PU2.1 X.25 device is PU2.0 XID Format 1

-

-

"Check the revision levels on the external equipment and\n\ upgrade them if necessary."

QLLC-3-NO_QLLCBUFFER

3-Error

M bit Reassembly failed - couldn't allocate a packet

The router ran out of memory to allocate buffers.

-

"Make sure that the router configuration is adequate for the service\n\ expected of it. You might want to tune the buffer pools or upgrade to\n\ a larger router. At the very least you will need more memory."

QLLC-3-INCALL_CFG

3-Error

Incoming call: No QLLC Service Access Point Configured for x.25 subaddress [chars]

A remote X.25 device is calling the router for QLLC service using a\n\ subaddress that was not configured by the X.25 routing facility. The\n\ subaddress was not configured for QLLC service.

-

"Correct the QLLC configuration. Configure only the subaddress on the\n\ QLLC service not the complete X.121 address that the remote X.25\n\ device uses."

QLLC-3-INCALL_NO_PARTNER

3-Error

Incoming call: No partner Mac Address configured - X.25 subaddress [chars]

There is an incoming call but a connection cannot be initiated \n\ to a partner since no partner is configured in a \qllc dlsw\ \n\ command for QLLC/DLSw+ only.

-

"Configure a partner for the incoming calling such as using the \n\ \"qllc dlsw partner\" command."

QLLC-3-PARTNER_MISMATCH

3-Error

Outgoing call: Partner Mac Address [enet] doesn't match configured partner [enet]

-

-

"Correct the QLLC configuration to match the right partner."

QLLC-3-QLLCMAP_ERR

3-Error

Incoming call: QLLC map entry not found

A software error in the router code occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

QLLC-3-NO_QSR

3-Error

No QLLC Service Access Points defined

No QLLC services have been configured even though the router will\n\ accept incoming calls for QLLC.

-

"Configure the QLLC service required."

QLLC-3-NO_RESOURCE

3-Error

Incoming Call: Insufficient resources available

This message is reporting insufficient system memory.

-

"Upgrade the memory."

RSRB-4-OPTNULL

4-Warning

Remopened and t NULL

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-PEERSTAT

4-Warning

Peer [chars] wrong state [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-CONNSTAT

4-Warning

Peer [chars] IFin bad connection state [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-BADLEN

4-Warning

Peer [chars] [chars] bad length [dec] trn [dec]

An internal software error occurred.

-

"If either message recurs call your technical support representative\n\ for assistance."

RSRB-3-BADVERSIONIF

3-Error

IFin: [chars]: version mismatch mine [dec] theirs [dec]

The remote end of a direct serial peer is running the wrong version of\n\ the system software. Either the local end the remote end or both are\n\ not up to date.

-

"Call your technical support representative for an update."

RSRB-3-BADVERSIONFST

3-Error

FSTin: [chars]: version mismatch mine [dec] theirs [dec]

The remote end of a direct serial peer is running the wrong version of\n\ the system software. Either the local end the remote end or both are\n\ not up to date.

-

"Call your technical support representative for an update."

RSRB-3-BADVERSIONTCP

3-Error

[chars]: [dec]/[inet]: version mismatch mine [dec] theirs [dec]

The remote end of a TCP remote peer is running the wrong version of\n\ the system software. Either the local end the remote end or both are\n\ not up to date.

-

"Call your technical support representative for an update."

RSRB-3-IFERR

3-Error

[chars]: [chars]: [chars] op [hec] len [dec] trn [dec]

The remote end of a direct serial RSRB connection detected a\n\ configuration problem or traffic that is not recognized by the\n\ configuration.

-

"Examine the configuration on both sides of the serial connection for\n\ possible problems. Examine the traffic being offered for propagation\n\ with respect to the configuration. The destination target ring is\n\ denoted by the value of trn."

RSRB-3-SENDPUNTIF

3-Error

[chars]: sent [chars] to [chars]

The local end of a direct serial RSRB connection detected a\n\ configuration problem or traffic that is not recognized by the\n\ configuration.

-

"Examine the configuration on both sides of the serial connection for\n\ possible problems. Examine the traffic being offered for propagation\n\ with respect to the configuration."

RSRB-3-FSTERR

3-Error

[chars]: [chars]: [inet] op [hec] len [dec] trn [dec]

The remote end of a direct serial RSRB connection detected a\n\ configuration problem or traffic that is not recognized by the\n\ configuration.

-

"Examine the configuration on both sides of the serial connection for\n\ possible problems. Examine the traffic being offered for propagation\n\ with respect to the configuration. The destination target ring is\n\ denoted by the value of trn."

RSRB-3-SENDPUNTFST

3-Error

[chars]: sent [chars] to [chars]

The local end of a direct serial RSRB connection detected a\n\ configuration problem or traffic that is not recognized by the\n\ configuration.

-

"Examine the configuration on both sides of the serial connection for\n\ possible problems. Examine the traffic being offered for propagation\n\ with respect to the configuration."

RSRB-4-BADLENIP

4-Warning

Peer [dec]/[inet] [chars] bad length [dec] trn [dec]

An internal software error occurred.

-

"If either message recurs call your technical support representative\n\ for assistance."

RSRB-4-ILLPEER

4-Warning

Peer [chars] [%-08x] illegal state [dec]

An internal software error occurred.

-

"If either of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-CONNILLSTATE

4-Warning

Peer [chars] CONN illegal state [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-CONIPST

4-Warning

Peer [dec]/[inet] CONN illegal state [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-3-HDRNOVRP

3-Error

Peer [inet] HDR no vrp

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-3-HDRVRP

3-Error

Peer [dec]/[inet] HDR vrp state wrong [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-HDRRECV

4-Warning

Peer [dec]/[inet] HDR recv state invalid not empty [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-3-NOMEMORY

3-Error

Unit [dec] no memory for [chars]

The requested operation could not be accomplished because of a low\n\ memory condition.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

RSRB-4-LOCAL

4-Warning

Unit [dec] local/vring set simultaneously vrn [dec]

An internal software error occurred.

-

"If either of these messages recur call your technical support\n\ representative for assistance."

RSRB-3-NOTREM

3-Error

Null idb and not remote

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-BADVRE

4-Warning

Bad vre type

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

RSRB-4-RNGXFAIL

4-Warning

Ring exchange failure resetting peer: [chars]

The RSRB peer initiation logic failed due to a memory shortage or\n\ congestion condition.

-

"The problem should clear and the peers should re-open without operator\n\ intervention."

SSLVPN-6-RADIUS_ATTRIBUTE_TOO_LONG

6-Information

Attribute length [dec] is longer than buffer size [dec]

This message indicates that the attribute configured on the Radius server is longer than the allocated buffer size and will be ignored.

-

"Reconfigure the radius attribute with the appropriate length"

SSLVPN-6-INVALID_RADIUS_CONFIGURATION

6-Information

Radius configured [chars] \[chars]\ does not exist

A Tunneling user has logged out from the given gateway/context

-

"The information is used to track user logout events. No" " action is required."

SSLVPN-5-UPDOWN

5-Notice

sslvpn [chars] : [chars] changed state to [chars]

sslvpn service state changed.

-

LOG_STD_NO_ACTION

SSLVPN-5-SSLVPNMGR_ERROR

5-Notice

[chars] [chars]

SSLVPN Manager error.

-

LOG_STD_NO_ACTION

SSLVPN-6-WEBVPN_APP_ACL_URL

6-Information

The request scheme: [chars] host : [chars] port : [dec] path : [chars]

A request is matched with application ACL.

-

LOG_STD_NO_ACTION

SSLVPN-6-WEBVPN_APP_ACL_NET

6-Information

The request source ip: [inet] destion ip : [inet] from user [chars] is [chars] by ACL

This message indicates that a Single Sign On session creation failed for the user. Session creation can fail for various reasons such as DNS lookup failure timeouts and retry attempts exceeded

-

"The information is used to track Single Sign On events. No" " action is required."

SSLVPN-5-LOGIN_AUTH_PASSED

5-Notice

vw_ctx: [chars] vw_gw: [chars] remote_ip: [inet] user_name: [chars] Authentication successful user logged in

This message indicates that login authentication succeeded for user

-

LOG_STD_NO_ACTION

SSLVPN-5-LOGIN_AUTH_FAILED

5-Notice

vw_ctx: [chars] vw_gw: [chars] remote_ip: [inet] user_name: [chars] Failed to contact authentication server

This message indicates that user session is terminated due to reason indicated

-

LOG_STD_NO_ACTION

SSLVPN-5-SSL_TLS_ERROR

5-Notice

vw_ctx: [chars] vw_gw: [chars] i_vrf: [dec] f_vrf: [dec] status: SSL/TLS connection error with remote at [inet]:[dec]

This message indicates that SSL/TLS connection has encountered error this normally means that either handshake failed or protocol error occured during life-time of the connection

-

"Check certificate and trustpoint configuration in global config mode" "as well as under webvpn gateway"

SSLVPN-5-SSL_TLS_CONNECT_OK

5-Notice

vw_ctx: [chars] vw_gw: [chars] i_vrf: [dec] f_vrf: [dec] status: SSL/TLS connection successful with remote at [inet]:[dec]

This message indicates that SSL/TLS handshake with peer was successful

-

LOG_STD_NO_ACTION

SSLVPN-5-HTTP_REQUEST_NOT_AUTHORIZED

5-Notice

vw_ctx: [chars] vw_gw: [chars] remote_ip: [inet] status: HTTP request without login cookie resource: [chars]

This message indicates that HTTP request doesn't have valid login cookie and is not authorized to access the resource

-

LOG_STD_NO_ACTION

SSLVPN-1-LICENSE_EXPIRED

1-Alert

IOS SSLVPN evaluation license has expired

IOS SSLVPN evaluation license has expired and a new license needs to be obtained. Existing user sessions will continue till they are closed and no new sessions will be allowed.

ssl-vpn

"Please visit http://www.cisco.com/go/sslvpn for instructions on how " "to obtain a IOS SSLVPN license"

SSLVPN-6-LICENSE_NO_FREE_COUNT

6-Information

All avaiable SSLVPN session licenses are in use

All SSLVPN sessions avaialable per current license are in use. Hence no additional user sessions can be allowed.

ssl-vpn

"To support more users additional license needs to be purchased. " "Please visit http://www.cisco.com/go/sslvpn for instructions on how " "to obtain a IOS SSLVPN license"

SSLVPN-4-LICENSE_COUNT_EXCEEDS_MAX_LIMIT

4-Warning

License count of currently installed license exceeds the maximum supported sessions on this platform

License count of currently installed license exceeds the maximum supported sessions on this platform. Excess count will not be utilized.

ssl-vpn

"Please collect the output of show license detail command and " "contact your technical support representative."

SSLVPN-3-LICENSE_NO_LICENSE

3-Error

No valid license is available to use IOS SSLVPN service

IOS SSLVPN service is a licensed feature on this platform. It will not be functional until a valid license is installed.

ssl-vpn

"Please visit http://www.cisco.com/go/sslvpn for instructions on how " "to obtain a IOS SSLVPN license"

SSP-3-EXCEEDMAXDOI

3-Error

SSP maximum DOI exceeded.

The configuration has exceeded the maximum number of SSP clients allowed on this device at any one time.

ipsec-ha

"Please verify your configuration and reduce the " "number of SSP clients running at the same time. If a large number of SSP " "clients is required contact your technical service representative."

SSP-3-NOSTART

3-Error

SSP could not initialize.

The SSP process could not successfully initialize. This may be due to unusual protocol startup times in certain topologies.

ipsec-ha

"Ensure that your IP redundancy mechanism HSRP " "config is valid and than all protocols have started. Configure SSP once " "more. If the error recurs contact your technical service advisor."

SSP-3-SRVSOCKCREATEFAIL

3-Error

SSP socket creation failed.

The SSP process could not establish a socket connection with the SSP peer. This is likely to occur in either of two situations the device is under extreme load or it is misconfigured.

ipsec-ha

"Verify that the SSP configuration is valid. " "Configure SSP to use a different port number. Reduce the load on the " "device."

SSP-3-DATACREATEFAIL

3-Error

Creation of required data structures failed.

SSP will not operate properly due to abnormal initialization of required data structures.

ipsec-ha

"Reload the device. If the error persists contact " "your technical service representative"

SSP-4-GROUPCREATEFAIL

4-Warning

The SSP group could not be created.

The maximum number of SSP groups has been reached.

ipsec-ha

"This is not an error situation. Only one SSP " "group is permitted at one time."

SSP-4-MISMATCHEDVERRECV

4-Warning

Wrong version on received packet.

The SSP version information in a received packet does not match what is currently running on this device.

ipsec-ha

"Verify the configuration of all the SSP peers. " "Ensure all peers are running the correct image."

SSP-4-CANNOTRUNVER

4-Warning

SSP version %-2d.%3d was requested but is not supported in this image.

The version of SSP requested by the active device is not available in this image. SSP will not run on this device until it is upgraded or the active is downgraded.

ipsec-ha

"Verify that all SSP peers are running compatible " "images and that the configuration on each device is as intended."

SSP-5-DISABLED

5-Notice

SSP entering disabled state.

SSP has entered its disabled state. This is normal under many circumstances. For example when the SSP configuration is changed or when a tracked interface is shut down or fails.

ipsec-ha

"If this change occurred because of failure on " "the active peer eliminate the cause of failure and reload the failed " "device."

SSP-6-STANDBY

6-Information

SSP entering standby state.

SSP has entered its standby state. This is normal.

ipsec-ha

"No action needed."

SSP-6-ACTIVE

6-Information

SSP entering active state.

SSP has entered its active state. This is normal.

ipsec-ha

"No action needed."

SSP-6-IPREDGRPADD

6-Information

An IP Redundancy group listed in the SSP config has been added to this device.

This is normal. The device may now become the active or the standby if no other configuration items are missing.

ipsec-ha

"No action needed."

SSP-6-IPREDGRPDEL

6-Information

An IP Redundancy group listed in the SSP config has been removed from this device.

This is normal. The device may not become the active or the standby if any configuration items are missing.

policy

LOG_STD_ACTION

SGPM-3-POLICY_CTX_POISONED

3-Error

Policy context %X has bad magic %X.

The magic number in the policy context is wrong.

policy

LOG_STD_ACTION

SGPM-3-PACL_NAME_TOO_LONG

3-Error

The pacl name [chars]-[chars] is too long it exceeds the maximum length

Too many acl entries have made the pacl name exceed the maximum supported length

policy

LOG_STD_ACTION

SGPM-3-POLICY_RULE_SERVICE_CONFIG_ERROR

3-Error

Service [chars] is configured incorrectly

In policy rule the service is configured incorrectly then a service-failed event will be thrown.

policy

LOG_STD_ACTION

SGPM-3-POLICY_CTX_ACTIVE

3-Error

Active policy context %X has bad magic %X.

The magic number in the active policy context is wrong.

policy

LOG_STD_ACTION

SSSMGR-3-NULL_FSM_CONTEXT

3-Error

Encountered a NULL SSS Mgr context in [chars]

Encountered a NULL context in SSS Manager.

sss

LOG_STD_ACTION

SSSMGR-3-INVALID_FSM_STATE

3-Error

Encountered an invalid SSS Mgr state [dec] in [chars]

An internal SSS Manager error occurred.

sss

LOG_STD_ACTION

SSSMGR-3-INIT

3-Error

Initialisation failure [chars]

An internal SSS Manager error occurred.

sss

LOG_STD_ACTION

SSSMGR-3-MEMORY_LOW

3-Error

Memory low [dec] times disconnecting session

Required memory is running low.

sss

LOG_STD_ACTION

SSSMGR-3-RESOURCE_OVERFLOW

3-Error

Resource overflow

A fixed size system resource has been exceeded.

sss

LOG_STD_ACTION

SSSMGR-3-NULL_INFO_STRING

3-Error

Received a NULL info string value.

An internal SSS Manager error occurred.

sss

LOG_STD_ACTION

SSSMGR-3-UNEXPECTED_SIP_INFO

3-Error

Encountered an unexpected SIP info: [chars]

Encountered an unexpected SIP info.

sss

LOG_STD_ACTION

SSSMGR-3-INVALID_INFO_TYPE

3-Error

Received an INVALID info type value [dec].

An internal SSS Manager error occurred.

sss

LOG_STD_ACTION

SSSMGR-3-INVALID_SERVICE_TYPE

3-Error

Received an INVALID service type [dec][chars].

-

-

-

SSSMGR-3-INFO_TYPE_NO_COPY_VECTOR

3-Error

info type has no copy vector [dec].

An internal SSS Manager error occurred.

sss

LOG_STD_ACTION

SSSMGR-3-DYNAMIC_UPDATE_NOT_SUPPORTED

3-Error

[[dec]] Dynamic session updates not allowed on this [chars] session. It is an unsupported configuration.

Updates on these sessions not supported. This is an unsupported configuration.

sss

LOG_STD_ACTION

SSSMGR-3-UNEXPECTED_MSG

3-Error

Encountered an unexpected message: [chars]

Encountered an unexpected message.

sss

LOG_STD_ACTION

SSSMGR-5-IFCFG_NOTALLWED_IN_SVC

5-Notice

Interface-config not allowed at service config level ignoring

Interface-config attribute is not allowed while in a service profile. It is only supported in user profiles.

sss

"Remove interface-config attribute from the service profile and " "reconfigure using a user profile."

SSSMGR-3-UNSUPPORTED_CFG

3-Error

Unsupported configuration detected: [uid: [dec]] [chars]

Unsupported configuration detected.

sss

LOG_STD_ACTION

SSSMGR-5-UNSUPPORTED_CFG_NOTICE

5-Notice

Unsupported configuration detected [chars]

The value of the specified configuration parameter was out of range. This is not considered an error as the value was adjusted to be within the supported range. Update the configuration source to a value within the supported range to avoid this message.

sss

LOG_STD_NO_ACTION

SSSMGR-3-ERROR_RESOURCE_OVERFLOW

3-Error

Resource overflow

A fixed size system resource has been exceeded.

sss

LOG_STD_ACTION

SSSMGR-4-WARN_RESOURCE_ABOVE_WM

4-Warning

Resource above watermark

A fixed size system resource is above watermark.

sss

LOG_STD_ACTION

SSSMGR-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

sss

LOG_STD_ACTION

SSSMGR-5-BB_LICENSE_REQUEST_SENT

5-Notice

Broadband license request sent for %lu license with configured license count %lu

-

sss

LOG_STD_ACTION

SSSMGR-5-BB_LICENSE_PROCUREMENT_SUCCESS

5-Notice

Successfully procured %lu BroadBand licenses

-

sss

LOG_STD_ACTION

SSSMGR-5-BB_LICENSE_PROCUREMENT_FAILURE

5-Notice

Failed to procure %lu BroadBand licenses

-

sss

LOG_STD_ACTION

SSSMGR-5-BB_LICENSE_RELEASE_SUCCESS

5-Notice

Successfully released all BroadBand licenses

-

sss

LOG_STD_ACTION

SSSMGR-5-BB_LICENSE_RELEASE_FAILURE

5-Notice

Failed to release all BroadBand licenses

-

sss

LOG_STD_ACTION

STORM_CONTROL-3-SHUTDOWN

3-Error

A packet storm was detected on [chars]. The interface has been disabled.

The amount of traffic detected on the interface exceeded the configured threshold values. Since the interface was configured to be shutdown if a packet storm event is detected it has been placed in error disable state.

-

"If automatic recovery is preferred the error disable recovery" "mechanism can be used. Determine and fix the root cause of" "the excessive traffic on the interface"

STORM_CONTROL-3-FILTERED

3-Error

A [chars] storm detected on [chars]. A packet filter action has been applied on the interface.

The amount of traffic detected on the interface exceeded the configured threshold values. The system is filtering excess traffic when packet is received. Packet traffic is not being forwarded by the system.

-

"Determine and fix the root cause of the excessive" "traffic on the interface."

STORM_CONTROL-5-ABATED

5-Notice

A [chars] storm abated on [chars]. Packet filter does not apply on the interface.

The amount of traffic on the interface is below the configured threshold values. The system is not filtering traffic when packet is received. Packet traffic is being forwarded by the system.

-

"No need further action"

STORM_CONTROL-3-TRAP

3-Error

A packet storm was detected on [chars]. Sending SNMP trap.

The amount of traffic detected on the interface exceeded the configured threshold values. Since the interface was configured to send SNMP trap if a packet storm event is detected it has has generated the trap.

-

"Determine and fix the root cause of the excessive traffic on the" " interface."

SPANTREE_FAST-7-PORT_FWD_UPLINK

7-Debug

[chars] [chars] moved to Forwarding UplinkFast.

-

-

-

STP_ISSU-2-INIT

2-Critical

STP ISSU client initialization failed to [chars]. Error: [dec] [chars]

The STP ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

L2

LOG_STD_ACTION

STP_ISSU-3-TRANSFORM_FAIL

3-Error

STP ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The STP ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the STP state between the active device and the standby device is not identical.

L2

"show issu session <client_id> and " "show issu negotiated version <session_id>"

STP_ISSU-3-MSG_NOT_OK

3-Error

STP ISSU client 'Message Type [dec]' is not compatible

The STP ISSU client received an incompatible message from the peer device. The message cannot be processed.

L2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

STP_ISSU-3-MSG_SIZE

3-Error

STP ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The STP ISSU client failed to calculate the MTU for the specified message. The STP ISSU client is not able to send the message to the standby device.

L2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

STP_ISSU-3-INVALID_SESSION

3-Error

STP ISSU client does not have a valid registered session.

STP ISSU client does not have a valid registered session.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-2-SESSION_REGISTRY

2-Critical

STP ISSU client failed to register session information. Error: [dec] [chars]

The STP ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-3-SESSION_UNREGISTRY

3-Error

STP ISSU client failed to unregister session information. Error: [dec] [chars]

The STP ISSU client failed to unregister session information.

L2

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-2-SESSION_NEGO

2-Critical

STP ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The STP ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

L2

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-2-SEND_NEGO_FAILED

2-Critical

STP ISSU client failed to send negotiation message. Error: [dec] [chars]

The STP ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

L2

"show logging and show checkpoint client"

STP_ISSU-2-SESSION_ARBITRATE

2-Critical

STP ISSU client failed to register arbitrate callback. Error: [dec] [chars]

The STP ISSU client failed to register arbitrate callback. If a problem occurs with the callback registration the standby device cannot be brought up properly.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-2-GET_BUFFER

2-Critical

STP ISSU client failed to get buffer for message. Error: [dec] [chars]

STP ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

L2

"show logging and show checkpoint client"

STP_ISSU-3-INVALID_CAPABILITY

3-Error

STP ISSU client: invalid capability list

STP ISSU client observed an error during capability negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-3-REJECTED_CAPABILITY

3-Error

STP ISSU client rejected capability '[chars]'

STP ISSU client rejected a capability during negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-3-REJECTING_CAPABILITY

3-Error

STP ISSU client rejecting capability '[chars]'

STP ISSU client is rejecting a capability during negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

STP_ISSU-3-POLICY_NOT_SUPPORTED

3-Error

STP ISSU client does not support Message Type [dec]

STP ISSU client received an message type which it does not support. The policy is applied to make the session incompatible.

L2

"show issu session <client_id>"

SPANTREE-3-PORT_SELF_LOOPED

3-Error

[chars] disabled.- received BPDU src mac [enet]

The source MAC address contained in a BPDU received on the listed interface matches the MAC address assigned to that interface This indicates the possibility that a port is looped back to itself possibly due to a diagnostic cable being plugged in. The interface will be administratively shutdown.

stp

"Check the interface configuration and any cable plugged into the " "interface. Once problem resolved re-enable interface by doing a " "no shutdown in the interface configuration."

SPANTREE-3-BAD_PORTNUM_SIZE

3-Error

Rejected an attempt to set the port number field size to [dec] bits valid range is [dec] to [dec] bits.

The spanning tree port identifier is a 16 bit wide field that is by default divided evenly between port priority and port number each sub field being 8 bits wide. This allows the port number field to represent port numbers between 1 and 255. However on systems with greater than 255 ports the size of port number portion of the port id must be increased to support the greater number of ports. This is done by the STP subsystem at system init time since the maximum number of ports on a particular platform will not change. This error would only occur due to an error in the platform specific code which caused it to request more or less

stp

"show version"

SPANTREE-7-RECV_1Q_NON_TRUNK

7-Debug

Received 802.1Q BPDU on non trunk [chars] [chars].

A SSTP BPDU was received on the listed interface that was not operationally a trunk.

pvst

"Verify that the configuration and operational state of the listed " "interface and that of the interface to which it is connected have " "the same mode access vs trunk. If mode is trunk verify the same "

SPANTREE-2-RECV_1Q_NON_1QTRUNK

2-Critical

Received 802.1Q BPDU on non 802.1Q trunk [chars] [chars].

The listed interface on which a SSTP BPDU was received was in trunk mode but not using 802.1Q encapsulation.

pvst

"Verify that the configuration and operational state of the listed " "interface and that of the interface to which it is connected have " "the same mode access vs trunk. If mode is trunk verify the same "

SPANTREE-2-RECV_PVID_ERR

2-Critical

Received BPDU with inconsistent peer vlan id [dec] on [chars] [chars].

The listed interface received a SSTP BPDU that is tagged with a VLAN id that does not match the VLAN id on which the BPDU was received. This occurs when the native VLAN is not consistently configured on both ends of a 802.1Q trunk.

pvst

"Verify that the configuration of the native VLAN id is consistent " "on the interfaces on each end of the 802.1Q trunk connection. " "Once corrected spanning tree will automatically unblock the interfaces " "as appropriate."

SPANTREE-2-RECV_BAD_TLV

2-Critical

Received SSTP BPDU with bad TLV on [chars] [chars].

The list interface received a SSTP BPDU that was missing the VLAN id tag. The BPDU is discarded.

pvst

LOG_STD_RECUR_ACTION

SPANTREE-7-BLOCK_PORT_TYPE

7-Debug

Blocking [chars] on [chars]. Inconsistent port type.

The listed interface is being held in spanning tree blocking state until the port type inconsistency is resolved.

pvst

"Verify that the configuration and operational state of the listed " "interface and that of the interface to which it is connected have " "the same mode access vs trunk. If mode is trunk verify the same "

SPANTREE-4-PORT_NOT_FORWARDING

4-Warning

[chars] [chars] [chars] [chars]

The port is not forwarding packets i.e it is not in a forwarding state

-

LOG_STD_ACTION

SPANTREE-2-BLOCK_PVID_PEER

2-Critical

Blocking [chars] on [chars]. Inconsistent peer vlan.

The spanning tree port associate with the listed spanning tree instance and interface will be held in spanning tree blocking state until the port VLAN Id PVID inconsistency is resolved. The listed spanning tree

pvst

"Verify that the configuration of the native VLAN id is consistent " "on the interfaces on each end of the 802.1Q trunk connection. " "Once corrected spanning tree will automatically unblock the interfaces " "as appropriate."

SPANTREE-2-BLOCK_PVID_LOCAL

2-Critical

Blocking [chars] on [chars]. Inconsistent local vlan.

The spanning tree port associate with the listed spanning tree instance and interface will be held in spanning tree blocking state until the Port VLAN ID PVID inconsistency is resolved. The listed spanning tree

pvst

"Verify that the configuration of the native VLAN id is consistent " "on the interfaces on each end of the 802.1Q trunk connection. " "Once corrected spanning tree will automatically unblock the interfaces " "as appropriate."

SPANTREE-2-UNBLOCK_CONSIST_PORT

2-Critical

Unblocking [chars] on [chars]. Port consistency restored.

The Port VLAN ID and/or Port Type inconsistencies have been resolved and spanning tree will now unblock the listed interface of the listed spanning tree instance as appropriate.

pvst

LOG_STD_NO_ACTION

SPANTREE-2-BLOCK_BPDUGUARD

2-Critical

Received BPDU on port [chars] with BPDU Guard enabled. Disabling port.

A BPDU was received in the interface specified in the error message that has the spanning tree BPDU Guard feature enabled. As a result the interface was administratively shut down.

pvst

"Either remove the device sending BPDUs or disable the BPDU Guard " "feature. The BPDU Guard feature can be locally configured on the " "interface or globally configured on all ports that have portfast " " enabled. After the conflict has been resolved reenable the " "interface by entering the <CmdBold>no shutdown<NoCmdBold> command " "in interface configuration mode."

SPANTREE-2-BLOCK_BPDUGUARD_VP

2-Critical

Received BPDU on port [chars] vlan [dec] with BPDU Guard enabled. Disabling vlan.

A BPDU was received on the interface and vlan specified in the error message. The spanning tree BPDU Guard feature was enabled and configured to shutdown the vlan. As a result the vlan was placed in the error-disabled state.

pvst

"Either remove the device sending BPDUs or disable the BPDU Guard " "feature. The BPDU Guard feature can be locally configured on the " "interface or globally configured on all ports that have portfast " "enabled. After the conflict has been resolved reenable the " "interface/vlan by entering the <CmdBold>clear errdisable<NoCmdBold> " "command."

SPANTREE-2-ROOTGUARD_CONFIG_CHANGE

2-Critical

Root guard [chars] on port [chars].

The spanning tree root guard configuration for the listed interface has been changed. If enabled any BPDU received on ths interface which advertizes a superior spanning tree root bridge to that already in use will cause the interface to be put into blocking state and marked as root guard inconsistent.

rootguard

"Verify that this is the desired configuration for the listed interface." "Correct it if this is not the desired configuration otherwise no further " "action is required."

SPANTREE-2-ROOTGUARD_BLOCK

2-Critical

Root guard blocking port [chars] on [chars].

A BPDU was received on the listed interface which advertizes a superior spanning tree root bridge to that currently in use. The interface is put into blocking state and marked as root guard inconsistent in order to prevent a suboptimal spanning tree topology to form.

rootguard

"Issue the <CmdBold>show spanning-tree inconsistentports<noCmdBold> " "command to review the list of interfaces with root guard inconsistencies." "Determine why devices connected to the listed ports are sending " "BPDUs with a superior root bridge and take action to prevent further " "occurances. Once the bogus BPDUs have been stopped the interfaces will " "automatically recover and resume normal operation." "Make sure that it is appropriate to have root guard enabled on the " "interface."

SPANTREE-2-ROOTGUARD_UNBLOCK

2-Critical

Root guard unblocking port [chars] on [chars].

The listed interface is no longer receiving BPDUs advertizing a superior root bridge. The root guard inconsistency is cleared for the interface and then it is taken out of the blocking state if appropriate.

rootguard

LOG_STD_NO_ACTION

SPANTREE-2-LOOPGUARD_CONFIG_CHANGE

2-Critical

Loop guard [chars] on port [chars].

The spanning tree loopguard configuration for the listed interface has been changed. If enabled the interface will be put into blocking state and marked as loopguard inconsistent when the message age timer expires because no BPDU were received from the designated bridge. This feature is mainly used to detect unidirectional links

loopguard

"Verify that this is the desired configuration for the listed interface." "Correct it if this is not the desired configuration otherwise no further " "action is required."

SPANTREE-2-LOOPGUARD_BLOCK

2-Critical

Loop guard blocking port [chars] on [chars].

The spanning tree message age timer has expired because and no BPDUs were received from the designated bridge. Since this condition could be caused by an unidirectional link failure the interface is put into blocking state and marked as loop guard inconsistent in order to prevent possible loops from being created

loopguard

-

SPANTREE-2-LOOPGUARD_UNBLOCK

2-Critical

Loop guard unblocking port [chars] on [chars].

The listed interface has received a BPDU and therefore if the inconsistency was due to an unidirectional link failure now the problem is not there anymore. The loop guard inconsistency is cleared for the interface which is taken out of the blocking state if appropriate.

loopguard

LOG_STD_NO_ACTION

SPANTREE-2-CHNL_MISCFG

2-Critical

Detected loop due to etherchannel misconfiguration of [chars] [chars]

A loop caused the misconfiguration of a channel group has been detected. An example of such a misconfiguration would be where the ports on one side of the etherchannel either aren't configured to be in the channel or failed to bundle for some reason while the other side has successfully bundled the ports into the etherchannel

stp

"Determine which local ports are involved using the command " "<CmdBold>show interfaces status err-disabled<noCmdBold> and then check " "etherchannel configuration on the remote device using the command " "<CmdBold>show etherchannel summary<noCmdBold> on the remote device. " "Once the configuration is corrected do " "<CmdBold>shutdown / no shutdown<noCmdBold> on the associated " "port-channel interface."

SPANTREE-3-ERR_NO_UNIDIR_EDGE

3-Error

[chars]: Portfast disabled reverting to bidirectional mode

Because UCP is for edge ports only portfast must be configured. This messageis typically seen when spanning-tree portfast is enabled on a port thenauthentication control-direction is set to inbound unidirectional and then

stp

"Re-enable portfast on the edge port. This will re-enable unidirectional""authentication control."

SPANTREE-5-EXTENDED_SYSID

5-Notice

Extended SysId [chars] for type [chars]

The extended system id feature has either enabled or disabled for the given type of spanning tree. If enabled the spanning tree instance identifier is stored in the lower portion of the bridge id priority field and this will cause the allowed values for the bridge priority to be limited to the range of 0 to 61440 in increments of 4096. If disabled the bridge id priority field consists entirely of the configured priority but some spanning tree features may not be available on a given platform i.e. 4096 vlan support. On some

stp

LOG_STD_NO_ACTION

SPANTREE-2-PVSTSIM_FAIL

2-Critical

Blocking [chars] port [chars]: Inconsitent [chars] PVST BPDU received on VLAN [dec] claiming root [dec]:[enet]

When a MST switch is connected to a PVST+ switch the CIST MST00

stp

"When STP is converging after a new switch or switch port is added" "to the topology this condition may happen transiently. The port" "unblocks automatically in such cases. If the port remains blocked" "identify the root bridge as reported in the message and configure" "a worse or better priority for the VLAN spanning tree consistent" "with the CIST role on the port of the MST switch. There could be more" "inconsistencies than the message indicates and the port will" "not recover until all such inconsistencies are cleared." "If you cannot determine which other VLANs have inconsistencies disable" "and reenable the port. This message will appear again and specify another" "VLAN with inconsistencies to be fixed. Repeat this process until all" "inconsistencies on all VLANs are cleared."

SPANTREE-2-PVSTSIM_OK

2-Critical

PVST Simulation inconsistency cleared on port [chars].

The listed interface is no longer receiving PVST BPDUs advertising an information inconsistent with the CIST port information. The PVST Simulation Inconsistency is cleared and the interface returns to normal operation

stp

LOG_STD_NO_ACTION

SPANTREE-6-PORT_STATE

6-Information

Port [chars] instance [dec] moving from [chars] to [chars]

The Spanning-Tree port has changed state.

cosmos

LOG_STD_NO_ACTION

SPANTREE-7-PORTDEL_SUCCESS

7-Debug

[chars] deleted from Vlan [dec]

The interface has been deleted from Vlan

stp

LOG_STD_NO_ACTION

SPANTREE-6-PORTDEL_ALL_VLANS

6-Information

[chars] deleted from all Vlans

The interface has been deleted from all Vlans

stp

LOG_STD_NO_ACTION

SPANTREE-6-PORTADD_ALL_VLANS

6-Information

[chars] added to all Vlans

The interface has been added to all Vlans

stp

LOG_STD_NO_ACTION

SPANTREE-5-TOPOTRAP

5-Notice

Topology Change Trap for [chars] [dec]

A trap has been generated to indicate the change in topology

stp

LOG_STD_NO_ACTION

SPANTREE-5-ROOTCHANGE

5-Notice

Root Changed for [chars] [dec]: New Root Port is [chars]. New Root Mac Address is [enet]

The Root has changed for an instance of spanning tree

stp

LOG_STD_NO_ACTION

SPANTREE-3-PRESTD_NEIGH

3-Error

pre-standard MST interaction not configured [chars]. Please configure:

The switch has received a pre-standard MST BPDU on a port that is not configured for pre-standard MST BPDU transmission. The switch will automatically adjust its mode of operation on this port and will start sending pre-standard BPDUs. However this auto-detection of pre-standard neighbors is not 100% accurate and it is recommended to configure explicitly the port for pre-standard MST BPDU transmission. This warning message will only be display once.

stp

"Configure 'spanning-tree mst pre-standard' on all the ports" "that are connected to switches running Cisco's pre-standard version " "of MST. It is recommended to migrate all the switches in the network to" "the IEEE standard MST version when it is possible."

SPANTREE-2-BRIDGE_ASSURANCE_BLOCK

2-Critical

Bridge Assurance blocking port [chars][chars].

BPDUs were not received from a neighboring switch on the interface that has spanning tree Bridge Assurance configured. As a result the interface was moved to the spanning tree Blocking state

cosmos

"Either disable Bridge Assurance configuration on the interface or " "make sure that the interface is connected to a L2 switch/bridge device"

SPANTREE-2-BRIDGE_ASSURANCE_UNBLOCK

2-Critical

Bridge Assurance unblocking port [chars][chars].

The interface listed in the message has been restored to normal spanning tree state after receiving BPDUs from the neighboring L2 switch/bridge

stp

LOG_STD_NO_ACTION

SPANTREE-2-PVST_PEER_BLOCK

2-Critical

PVST+ peer detected on port [chars]

PVST+ BPDUs are detected on the listed interface when MSTP PVST+

stp

"Please make sure the PVST+ switch is removed from the network or " "enable the MSTP PVST Simulation feature."

SPANTREE-2-PVST_PEER_UNBLOCK

2-Critical

Unblocking port [chars]

The listed interface is no longer receiving the PVST+ BPDUs. The inconsistency is cleared and the interface returns to normal operation.

stp

LOG_STD_NO_ACTION

SPANTREE-2-NOMEM

2-Critical

Memory Allocation Failure - [chars]: [chars]

The system could not allocate the memory that is required for the STP feature. This condition might indicate that more memory must be installed on the system.

stp

show tech-support and show logging

SPANTREE_VLAN_SHIM-2-MAX_INSTANCE

2-Critical

Platform limit of [dec] STP instances exceeded. No instance created for [chars] port [chars].

-

-

-

SPANTREE_VLAN_SHIM-3-ADD_REGISTRY_FAILED

3-Error

Subsystem [chars] fails to add callback function [chars]

Other subsystem must have mistakenly add its own callback functions. This syslog is for debugging purpose.

stp

LOG_STD_NO_ACTION

SW_DA-3-DA_INIT_FAILED

3-Error

Unable to initialize dual-active detection/recovery \[chars]\

The switch was unable to setup dual-active detection/recovery system.\n\ The result is that dual-active detection/recovery may not work.

dual-active

LOG_STD_NO_ACTION

SW_DA-3-DA_JOB_FAILED

3-Error

Unable to handle dual-active recovery : [chars]

The switch was unable to handle dual-active recovery job. This could \n\ be because the job handler does not exist or sending a message to \n\ the recovery job handler failed.

dual-active

LOG_STD_NO_ACTION

SW_DA-3-DA_LOOPBACK_SHUTDOWN_FAILED

3-Error

Unable to shutdown loopback interface : [chars] [chars]

The switch was unable to handle shutdown of loopback interface while\n\ the switch is in recovery mode. This could be because the job handler\n\ does not exist or sending a message to the job handler\n\ failed.

dual-active

LOG_STD_NO_ACTION

SW_DA-1-DETECTION

1-Alert

detected dual-active condition[chars]

The specified dual-active method detected a dual-active scenario and caused switch to go into recovery mode.

dual-active

LOG_STD_NO_ACTION

SW_DA-1-RECOVERY

1-Alert

Dual-active condition detected: Starting recovery-mode all non-VSL interfaces have been shut down

A dual-active situation has occurred due to VSL going down. The VSL has become inactive and both chassis have taken over the role of the active virtual switch. To fix this condition the standby virtual switch has become active and taken control of the network. All non-VSL interfaces on the original active virtual switch will be errdisabled or shut down.

dual-active

"Attempt to determine the reason why VSL has gone down and " "correct it. Once VSL has been re-established the original " "active virtual switch will reload."

SW_DA-1-VSL_RECOVERED

1-Alert

VSL has recovered during dual-active situation: Reloading switch [dec]

The VSL between the two active virtual switches in a dual-active situation has gone up. The virtual switch in recovery mode must be reloaded to re-enable all non-VSL interfaces which were shut down when the dual-active situation was first entered.

dual-active

LOG_STD_NO_ACTION

SW_DA-3-DA_RELOAD_FAILED

3-Error

Unable to reload the chassis : [chars]

The switch was unable to reload the chassis while\n\ the switch is in recovery mode. This could be because the job handler\n\ does not exist or sending a message to the job handler\n\ failed.

dual-active

LOG_STD_NO_ACTION

SW_DA-3-DA_CAPTURE_CONFIG_FAILED

3-Error

Unable to capture IP address configured on [chars]

The switch was unable to capture config of management interface\n\ as part of changing IP address on interface to the IP configured\n\ for recovery.

dual-active

LOG_STD_NO_ACTION

SW_DA-3-DA_CLEAR_IP_FAILED

3-Error

Unable to clear IP address configured on [chars]

The switch was unable to clear IP address of management interface\n\ as part of changing IP address on interface to the IP configured\n\ for recovery.

dual-active

LOG_STD_NO_ACTION

SW_DA-3-DA_APPLY_IP_FAILED

3-Error

Unable to set recovery IP address on [chars]

The switch was unable to set IP address of management interface\n\ to the IP configured for recovery.

dual-active

LOG_STD_NO_ACTION

FASTHELLO-3-REGISTRY_ADD_ERR

3-Error

Failure in adding to [chars] registry

Could not add a function to the registry

cat4k-vss

LOG_STD_NO_ACTION

FASTHELLO-3-FH_QUEUE_CREATE_FAILED

3-Error

Unable to create watched queue \[chars]\

Unable to create the specified watched queue because of unknown reasons

cat4k-vss

LOG_STD_NO_ACTION

FASTHELLO-3-FH_MANAGED_CHUNK_FAILED

3-Error

Unable to create managed chunk\[chars]\

Unable to create the specified watched boolean due to unknown reasons

cat4k-vss

LOG_STD_NO_ACTION

FASTHELLO-6-FH_VERSION_MISMATCH

6-Information

Local switch protocol version :[dec] Peer switch protocol version : [dec]

Informational messages regarding the software versions running on the switch

cat4k-vss

LOG_STD_ACTION

FASTHELLO-6-FH_BAD_CONFIG

6-Information

Fast-hello PDU received on unconfigured interface. Peer_slot: [dec]Peer_port: [dec]

Informational messages regarding the configuration of the dual-active fast-hello interface

cat4k-vss

"Investigate and correct this misconfiguration"

FASTHELLO-6-FH_SAME_SWITCH

6-Information

Fast-hello PDU received from interface configured on same switch. Slot: [dec]Port: [dec]

Informational messages regarding the configuration of the dual-active fast-hello interface

cat4k-vss

"Investigate and correct this misconfiguration"

FASTHELLO-6-FH_DIFF_DOMAIN

6-Information

Fast-hello PDU received from different domain. Peer_slot: [dec]Peer_port: [dec]

Informational messages regarding the configuration of the dual-active fast-hello interface

cat4k-vss

"Investigate and correct this misconfiguration"

FASTHELLO-5-FH_UP

5-Notice

Fast-Hello interface [chars] status changed to link up\n

FASTHELLO STATUS CHANGED to UP with more detail status

cat4k-vss

LOG_STD_NO_ACTION

FASTHELLO-2-FH_DOWN

2-Critical

Fast-Hello interface [chars] lost dual-active detection capability\n

FASTHELLO STATUS CHANGED to DOWN with more detail status

cat4k-vss

LOG_STD_NO_ACTION

FASTHELLO-5-FH_DUAL_ACTIVE_CAP

5-Notice

Fast-Hello interface [chars] became dual-active detection capable\n

FASTHELLO STATUS became dual-active detection capable with more detail status

cat4k-vss

LOG_STD_NO_ACTION

PF-4-MEM_UNAVAIL

4-Warning

Memory was not available to perform the protocol filtering action

Protocol filtering is unable to operate because of a lack of memory

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

PF-4-UNKN_ERR

4-Warning

An unknown operational error occurred

Protocol filtering is unable to operate because an internal operation\n\ generated an error which was not expected to ever happen

-

"Because of the unexpected nature of the problem the only recommended\n\ action is to reload the device"

PF-4-PROC_START_ERR

4-Warning

Protocol filtering unable to start

The protocol filtering process was unable to be created for unknown\n\ reasons.

-

"Start protocol filtering again in case the condition was transient.\n\ If this still fails reload the device"

PF-5-TRUNKPFOFF

5-Notice

Protocol filtering disabled on interface [chars] because it is a trunk

Protocol filtering does not operate on trunks. The protocol filtering\n\ configuration stays with the trunk port but it has no effect and does\n\ not appear when you show all non-default protocol filters.

-

-

PF-5-SPANDSTOFF

5-Notice

Protocol filtering disabled on interface [chars] because it is a span destination

SWC Sensor Registration failed!

-

"This message is for informational purposes only"

SWC-3-SWC_HA_INIT_FAILURE

3-Error

Failed to register with RF rc = [dec]

Message HA message received from peer node

-

"This message is for informational purposes only"

IGMP_QUERIER-4-SAME_SRC_IP_ADDR

4-Warning

An IGMP General Query packet with the same source IP address [inet]

The IGMP querier has received an IGMP General Query message with a source IP address identical to that configured for the IGMP querier itself. This is considered a network configuration error.

igmp

"Check IGMP querier source IP address configuration on the router " "or switch connected via the port identified." "Ensure unique source IP addresses are configured on each system. "

IGMP_QUERIER-4-ZERO_SRC_IP_ADDR

4-Warning

An IGMP General Query packet with source IP address that contained all zeroes is received in VLAN [dec] on port [chars].

The IGMP querier has received an IGMP General Query message with a source IP address that contained all zeroes. Some IGMP clients cannot process General Query with source IP address that contained all zeroes.

igmp

"Check the source IP address of the IGMP querier that is on the router " "or switch connected to the port specified in the message. "

IGMP_QUERIER-4-QUERIER_MROUTER_DETECTED

4-Warning

An external IGMP querier or a multicast router has been detected in VLAN [dec] on port [chars].

An external querier or multicast router has been detected in the VLAN. The IGMP querier function should not be enabled when there is external querier or multicast router present in the VLAN.

igmp

"Either manually disable the IGMP querier on this system or disable " "querier or PIM/DVMRP on the multicast routers identified. The IGMP "

IGMP_QUERIER-6-NO_QUERIER_MROUTER_DETECTED

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because no external querier or multicast router has been detected.

No external querier or multicast router has been detected. As a result the IGMP querier function has now been enabled.

igmp

"No action is required."

IGMP_QUERIER-4-SNOOPING_DISABLED

4-Warning

The IGMP querier is operationally disabled in VLAN [dec] because IGMP snooping has been disabled in this VLAN.

IGMP snooping has been detected as being disabled on this VLAN. The IGMP querier function should not be operationally enabled when IGMP snooping is disabled.

igmp

"Ensure that IGMP snooping is enabled globally and on the VLAN " "reported. "

IGMP_QUERIER-6-SNOOPING_ENABLED

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because IGMP snooping is no longer disabled.

IGMP snooping has now been enabled and as a result the IGMP querier function has now been enabled.

igmp

"No action is required."

IGMP_QUERIER-4-PIM_ENABLED

4-Warning

The IGMP querier is operationally disabled in VLAN [dec] because PIM has been enabled on the SVI.

PIM has been detected on the SVI. The IGMP querier function should not be operationally enabled when PIM is enabled on the SVI.

igmp

"Ensure that PIM is disabled on the SVI. "

IGMP_QUERIER-6-PIM_DISABLED

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because PIM is no longer enabled on the SVI.

PIM has been disabled on the SVI and as a result the IGMP querier function has now been enabled.

igmp

"No action is required."

IGMP_QUERIER-4-VLAN_NOT_FWD

4-Warning

The IGMP querier is operationally disabled in VLAN [dec] because VLAN is not in forwarding state.

The IGMP querier function is not be operationally enabled when VLAN is not forwarding.

igmp

"Check spanning tree state for this VLAN."

IGMP_QUERIER-6-VLAN_FWD

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because the VLAN has entered forwarding state.

The VLAN has been placed in the forwarding state and as a result the IGMP querier function has now been enabled.

igmp

"No action is required."

IGMP_QUERIER-4-NO_IP_ADDR_CFG

4-Warning

The IGMP querier cannot send out General Query messages in VLAN [dec] because there is no IP address configured on the system.

An IP address should be specified for the IGMP querier either at the global or per VLAN level.

igmp

"Configure a source IP address for the IGMP querier. "

SWITCH_SPAN_ISSU-3-INIT

3-Error

span switch ISSU client initialization failed at [chars] error [chars]

span switch ISSU client could not be initiailzed this will cause catastrophic failure when ISSU upgrade or downgrade is performed.

c7600-l2

LOG_STD_SH_TECH_ACTION

SWITCH_SPAN_ISSU-3-TRANSFORM

3-Error

span switch ISSU client [chars] transform failed error [chars]

span switch ISSU client could not transform the message. If the transmit transformation failed it means that the checkpoint message can not be sent to the standby unit. If the receive transformation failed it means that the checkpoint message can not be applied on the standby unit. In both cases the span switch state will not be identical with the active unit.

c7600-l2

"show issu session <client_id> and " "show issu negotiated version <session_id>"

SWITCH_SPAN_ISSU-3-MSG_NOT_OK

3-Error

span switch ISSU client message [dec] is not compatible

span switch ISSU client received an incompatible message from the peer unit. Since the message is not compatible it can be processed by this unit

c7600-l2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SWITCH_SPAN_ISSU-3-MSG_SIZE

3-Error

span switch ISSU client failed to get the message size for message [dec]

span switch ISSU client failed to calculate message size for the message specified. The span switch ISSU client will not be able to send message to the standby unit.

c7600-l2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SWITCH_SPAN_ISSU-3-SESSION

3-Error

span switch ISSU client [chars]

span switch ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up.

c7600-l2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated " "capability <session_id>"

SWITCH_SPAN_ISSU-3-SEND_FAILED

3-Error

span switch ISSU client failed to send a negotiation message error [dec]

span switch ISSU client could not send a session negotiation message to the peer. When there is a problem in the negotiation the standby unit can not be brought up.

c7600-l2

"show logging and show checkpoint client"

SWITCH_SPAN_ISSU-3-BUFFER

3-Error

span switch ISSU client failed to get buffer for message error [dec]

span switch ISSU client failed to get buffer for building a negotiation message. Hence it can send the negotiation message to the standby unit. When there is a problem in the negotiation the standby unit can not be brought up.

c7600-l2

"show logging and show checkpoint client"

SWITCH_SPAN_ISSU-3-CAPABILITY

3-Error

span switch ISSU client [chars]

span switch ISSU client observed an error during capability negotiation. When this error happens there is a mismatch between the client capability between the active and standby unit.

c7600-l2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SWITCH_SPAN_ISSU-3-POLICY

3-Error

span switch ISSU client message type [dec] is [chars]

span switch ISSU client received an message type which it does not support. The policy is applied to make the session compatible.

c7600-l2

"show issu session <client_id>"

SW_MATM-4-MACFLAP_NOTIF

4-Warning

Host [enet] in [chars] [dec] is flapping between port [chars] and port [chars]

The system has found the specified host moving between the specified ports.

-

"Check the network for possible loops."

SW_MATM-4-WIRELESS_MAC_MOVE_NOTIF

4-Warning

Host [enet] moving from Port [chars] to Port [chars] as wireless entry

The system has found the specified host moving between the specified ports. The host transitioned from wired to wireless.

-

"Check that this move does not happen too often"

SW_MATM-4-WIRELESS_MAC_MOVE_DENY_NOTIF

4-Warning

Host [enet] moving from Port [chars] to Port [chars] as wired entry not allowed

The system has found the specified host moving between the specified ports. The host transition from wireless to wired not allowed.

sw-matm mac-table

"Check that this move does not happen too often"

MATM_ISSU-3-INIT

3-Error

MATM ISSU client initialization failed at [chars] error [chars]

MATM ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

mac_addresses

LOG_STD_SH_TECH_ACTION

MATM_ISSU-3-TRANSFORM

3-Error

MATM ISSU client [chars] transform failed error [chars]

MATM ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the MATM state will not\n\ be indentical with the active unit.

mac_addresses

"show issu session <client_id> and \n\ show issu negotiated version <session_id>"

MATM_ISSU-3-MSG_NOT_OK

3-Error

MATM ISSU client message [dec] is not compatible

MATM ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

mac_addresses

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

MATM_ISSU-3-MSG_SIZE

3-Error

MATM ISSU client failed to get the message size for message [dec]

MATM ISSU client failed to calculate message size\n\ for the message specified. The MATM ISSU client will not\n\ be able to send message to the standby unit.

mac_addresses

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

MATM_ISSU-3-SESSION

3-Error

MATM ISSU client [chars]

MATM ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

mac_addresses

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

MATM_ISSU-3-SESSION_UNREGISTRY

3-Error

MATM ISSU client failed to unregister session information. Error: [dec] [chars]

The MATM ISSU client failed to unregister session information.

mac_addresses

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MATM_ISSU-3-SEND_FAILED

3-Error

MATM ISSU client failed to send a negotiation message error [dec]

MATM ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the \n\ negotiation the standby unit can not be brought up.

mac_addresses

"show logging and show checkpoint client"

MATM_ISSU-3-BUFFER

3-Error

MATM ISSU client failed to get buffer for message error [dec]

MATM ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

mac_addresses

"show logging and show checkpoint client"

MATM_ISSU-3-CAPABILITY

3-Error

MATM ISSU client [chars]

MATM ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

mac_addresses

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

MATM_ISSU-3-POLICY

3-Error

MATM ISSU client message type [dec] is [chars]

MATM ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

mac_addresses

"show issu session <client_id>"

MATM_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

MATM ISSU client capability exchange result incompatible.

The MATM ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

mac_addresses

"show issu negotiated capability <Session_ID>"

MATM_ISSU-3-CAP_INVALID_SIZE

3-Error

MATM ISSU client capability list is empty.

The MATM ISSU client capability exchange list size\n\ is invalid.

mac_addresses

"show issu capability entries <Client_ID>"

MATM_CF-4-QUEUE_OVERLIMIT

4-Warning

MATM CF dropped message type [dec] as queue limit has reached

MATM checkpoint client could not send some messages because\n\ an internal queue was full. Mac address table on the standby\n\ might not be in sync and can impact behavior upon switchover.

mac_addresses

LOG_STD_SH_TECH_ACTION

PT-3-PT_HW_UNAVAIL

3-Error

Protocol Tunneling hardware resource not available. [chars]

Protocol tunneling could not be enabled because no redirect registers are available. Protocol Tunneling requires redirect registers

cat6000-l2

"Disable any applications that uses redirect registers and try" "configuring the Protocol Tunneling again"

PT-3-PT_NO_SWSB

3-Error

Protocol Tunneling software subblock not found. [chars]

The software subblock that is used for protocol tunnelling could not be found for the port specified in the message text. Protocol tunnelling has been disabled on this port.

cat6000-l2

LOG_STD_ACTION

IDBMAN-3-VLANINUSE

3-Error

[chars]: Vlan [dec] is in use by [chars]

Each L3 interface has a Vlan associated with it. This message indicates \n\ that the Vlan associated with the interface is being used by some other \n\ L3 Interface which is not anticipated to happen

<platform>

LOG_STD_NO_ACTION

IDBMAN-3-INVALIDVLAN

3-Error

[chars]: trying to use invalid Vlan [dec]

There is an internal error that caused an invalid Vlan to be used \n\ by the software.

<platform>

LOG_STD_ACTION

IDBMAN-3-VLANNOTSET

3-Error

[chars]: Vlan [dec] not set since it already has Vlan [dec]

There is an internal error that caused an interface to not have its\n\ Vlan set to the requested value

<platform>

LOG_STD_ACTION

IDBMAN-6-VLANMAPPED

6-Information

Vlan [dec] is mapped to [chars]

Informational message indicating that the given Vlan is mapped \n\ to the given interface

<platform>

LOG_STD_NO_ACTION

IDBMAN-3-AGGPORTMISMATCH

3-Error

[chars][dec] / [dec] does match internal slot/port state [chars][dec] / [dec]

There is an internal error that caused an invalid aggregate port\n\ to be used by the software.

<platform>

LOG_STD_ACTION

IDBMAN-3-INVALIDAGGPORTBANDWIDTH

3-Error

[chars][dec] / [dec] has an invalid bandwidth value of [dec]

There is an internal error that caused an invalid bandwidth to be used\n\ for an aggregate port.

<platform>

LOG_STD_ACTION

IDBMAN-3-DELETEDAGGPORT

3-Error

[chars][dec] / [dec] Group [dec] has been deleted but is being reused.

There is an internal error that caused an interface that has been deleted\n\ to be reused for a new aggregate port.

<platform>

LOG_STD_ACTION

IDBMAN-3-NOTANAGGPORT

3-Error

[chars] [dec] / [dec] is not an aggregate port

There is an internal error that caused an interface that is not an aggregate\n\ port to be used for aggregate port operations

<platform>

LOG_STD_ACTION

IDBMAN-3-INVALIDPORT

3-Error

[chars]: trying to use invalid port number [dec] Max [dec]

There is an internal error that caused an invalid port numer to be used\n\ by the software.

<platform>

LOG_STD_ACTION

IDBMAN-4-ACTIVEPORTSINAGGPORT

4-Warning

[chars] [dec] / [dec] has [dec] active ports but is being removed

There is an internal error that caused an aggregate port with active ports\n\ to be removed

<platform>

LOG_STD_ACTION

IDBMAN-3-PORTNOTINAGGPORT

3-Error

[chars][dec] / [dec] is not present in Aggport [chars][dec] / [dec]

There is an internal error that caused an invalid port to be referred\n\ to be part of an aggregate port.

<platform>

LOG_STD_ACTION

IDBMAN-4-REMOVED_NONDEFAULT_CONFIG

4-Warning

Removed non default configuration for interfaces in [chars]

In SSO mode the non-default configuration for any removed linecard is\n\ not synced to the standby during the bulk sync and it is removed from\n\ the configuration to avoid a config mismatch between active and standby\n\ supervisors.

<platform>

LOG_STD_NO_ACTION

IDBMAN-3-IIF_ID_REGISTRATION_FAILED

3-Error

IIF_ID registration failed for Port [chars] due to memory allocation failure. Port has been shutdown

The system is low on memory due to which IIF-ID registration failed. This results in failure to apply polices such as QoS and Security acls on this port.

<platform>

LOG_STD_REDUCE_ACTION "Once memory is available " "run 'no shutdown' on the port."

VLAN_PORT-3-IIF_ID_ALLOC_FAILED

3-Error

IIF_ID alloc failed for vlan-port: Port [chars] in Vlan [dec] due to memory allocation failure. Some features will not work.

The system is low on memory due to which IIF-ID allocation failed. This results in failure to apply polices such as QoS on this vlan-port.

vlan-port

LOG_STD_REDUCE_ACTION "Once memory is available unconfigure and reconfigure the vlan on the" "port"

VLAN_PORT-3-IIF_ID_REGISTRATION_FAILED

3-Error

IIF_ID registration failed for vlan-port: Port [chars] in Vlan [dec] due to memory allocation failure. Some features will not work. Vlan-port is errdisabled

The system is low on memory due to which IIF-ID registration failed. This results in failure to apply polices such as QoS on this vlan-port. If port is carrying the vlan vlan-port is errdisabled.

sw-vlan

LOG_STD_REDUCE_ACTION "Once memory is available " "run 'clear errdisable interface <intf> vlan <vlanId>' " "or run 'shutdown' followed by 'no shutdown' on the port."

BACKUP_INTERFACE-5-PREEMPT

5-Notice

Preempting interface [chars] in backup pair [chars] [chars] preemption mode is [chars]

Preempting the current forwarding interface in the backup interface pair.

backup_int

LOG_STD_NO_ACTION

BACKUP_INTERFACE-5-VLB_NON_TRUNK

5-Notice

Warning: Flexlink VLB is not allowed on non-trunk ports. Please configure [chars] to be a trunk port.

Flexlink VLB detects a non-trunk port.

backup_int

LOG_STD_NO_ACTION

LOOPDETECT-4-ERR_DISABLE

4-Warning

loopdetect frame sent on [chars] is received on [chars] err-disabling [chars]

-

-

-

LOOPDETECT-4-SYSLOG

4-Warning

loopdetect frame sent on [chars] is received on [chars] loopdetection on port [chars]

This is a defensive measure that will put the interface in err-disable state when it detects a loop in the current or connected swtich. A recovery will be attempted after the configured retry time default 5 minutes if auto recovery is enabled.

loopdetect

LOG_STD_SH_TECH_ACTION

LOOPDETECT-4-INVALID_HWIDB

4-Warning

invalid hwidb for src_mac [enet]

Unable to translate the source macaddress in the loopdetect frame to a valid interface

loopdetect

LOG_STD_SH_TECH_ACTION

VSLP_ISSU-3-INIT

3-Error

VSLP ISSU client initialization failed at [chars] error [chars]

VSLP ISSU client could not be initiailzed this will cause catstrophic failure when ISSU upgrade or downgrade is performed.

vslp

LOG_STD_SH_TECH_ACTION

VSLP_ISSU-3-TRANSFORM

3-Error

VSLP ISSU client [chars] transform failed for [chars] message error [chars]

VSLP ISSU client could not transform the message. If the transmit transformation failed it means that the VSLP message can not be sent to the standby unit. If the receive transformation failed it means that the VSLP message can not be processed on the standby unit.

vslp

"show issu session <client_id> and " "show issu negotiated version <session_id>"

VSLP_ISSU-3-MSG_NOT_OK

3-Error

VSLP ISSU client message [chars] is not compatible

VSLP ISSU client received an incompatible message from the peer unit. Since the message is not compatible it cannot be processed by this unit

vslp

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

VSLP_ISSU-3-SESSION

3-Error

VSLP ISSU client [chars]

VSLP ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the peer switch can not be brought up as standby causing to have two active switches in the system.

vslp

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

VSLP_ISSU-3-SEND_FAILED

3-Error

VSLP ISSU client failed to send a negotiation message

VSLP ISSU client could not send a session negotiation message to the peer. When there is a problem in the negotiation the peer switch unit can not be brought up as standby causing to have two active switches in the system.

vslp

"show issu session <client_id> and " "show issu negotiated version <session_id>"

VSLP_ISSU-3-ISSU_ERROR

3-Error

[chars] failed with error code [dec] for peer [enet]

ISSU API failed to do some operation for VSLP layer The message includes the error code from ISSU library

vslp

show issu fsm

VSLP_ISSU-3-NEGO_FAILED

3-Error

VSLP ISSU start nego session with peer [enet] with error code [chars]

The VSLP ISSU could not start its negotiation process.

vslp

"show issu fsm"

VSLP_ISSU-3-RX_QUEUE_FAIL

3-Error

Unable to enqueue received packet for processing

An internal error occurred that prevented a packet from being enqueued to the packet processing queue for processing. The packet was dropped

vslp

LOG_STD_NO_ACTION

VSLP_ISSU-3-INVALID_PROC_EVENT

3-Error

Got event [dec]:[dec]

The process was woken up with an invalid event

vslp

LOG_STD_NO_ACTION

VSLP_ISSU-3-PROC_CREATE_FAILED

3-Error

Unable to create process \[chars]\

Unable to create the specified process because of unknown reasons

vslp

LOG_STD_NO_ACTION

VSLP_ISSU-3-CAP_RESULT_INCOMPAT

3-Error

VSLP ISSU client capability exchange result incompatible.

VSLP ISSU client capability exchange result incompatible

vslp

"show issu negotiated capability <Session_ID>"

VSLP_ISSU-3-RX_BAD_INTERFACE

3-Error

Incorrect port [dec]/[dec] for received packet

An VSLP ISSU packet was received that has incorrect received packet info. This could mean either that a VSLP ISSU packet was received from an interface on which VSLP is not enabled. The packet was dropped

vslp

LOG_STD_NO_ACTION

VSLP_ISSU-3-QUEUE_CREATE_FAILED

3-Error

Unable to create watched queue \[chars]\

Unable to create the specified watched queue because of unknown reasons

vslp

LOG_STD_NO_ACTION

VSLP_ISSU-3-NULL_ENTRY

3-Error

Null [chars] entry in [chars]

A NULL entry was passed in the specified operation

vslp

LOG_STD_NO_ACTION

VSLP_ISSU-3-INTERNAL

3-Error

An internal error occurred: [chars]

An unexpected sowftware error during the specified operation

vslp

LOG_STD_NO_ACTION

VSLP-3-REGISTRY_ADD_ERR

3-Error

Failure in adding to [chars] registry

Could not add a function to the registry

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-ICC_ERR

3-Error

[chars]

Failure during the ICC operation

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_TIMER_CREATE_FAIL

3-Error

Instance:[dec] Peer:[dec]: Unable to create RRP timer

RRP timer creation failed for the particular instance and peer

vslp

LOG_STD_NO_ACTION

VSLP-5-RRP_ACTIVE_PEER_DOWN

5-Notice

Communication to active peer went down. Triggering switchover...

Role resolution protocol got an indication that communication to active peer has gone down. This will in turn trigger a switchover

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_NO_PEER

5-Notice

No VSLP peer found. Resolving role as Active

VSLP could not communicate with any peer. Hence continuing to boot up as active

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_PEER_TIMEOUT

5-Notice

VSLP peer timer expired without detecting peer. Resolving role as Active

Role resolution protocol could not communicate with any peer Before peer timer expiry. Hence continuing to boot up as active

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_ROLE_RESOLVED

5-Notice

Role resolved as [chars] by VSLP

Role resolution protocol communicated with peer and resolved role

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_INVALID_INSTANCE

3-Error

Instance value [dec] is invalid

The instance value corresponds to an invalid instance

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_INSTANCE_OUT_OF_BOUNDS

3-Error

Instance value [dec] is outside the expected range

The instance value received is out of bounds

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_PEER_INFO_ERR

3-Error

Instance:[dec] Peer:[dec]: Peer [chars]

RRP encountered an error associated with this peer

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_MEMORY_ALLOC_ERR

3-Error

Instance:[dec] Peer:[dec]: No memory available for [chars]

VSLP could not obtain the memory it needs

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_UNSAVED_CONFIG

5-Notice

Ignoring system reload since there are unsaved configurations.\n Please save the relevant configurations

Role resolution protocol got an indication that we need to reload the system due to role change from active to standby. But the box has some unsaved configurations which will be lost. Hence the user must save relevant configurations.

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_WR_MEM_PROGRESS

5-Notice

Ignoring system reload since config save operation is in progress.\n Please wait till the configs are saved

Role resolution protocol got an indication that we need to reload the system due to role change from active to standby. Since the config save is in progress box will not be reloaded.

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_MSG

5-Notice

[chars]

Role resolution protocol event

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_RT_CFG_CHG

5-Notice

Configured [chars] value is different from operational value.\n Change will take effect after config is saved and switch [dec] is reloaded.\n

Role resolution protocol configuration changes by user

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_ERR_MSG

3-Error

[chars]

VSLP Role resolution protocol detected an error

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_UNEXPECTED_ROLE

3-Error

Unexpected roles. Local role = [chars] Peer role = [chars]

VSLP Role resolution protocol determined inconsistent role information

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_VALUE_ERR

3-Error

[chars]: [dec]

VSLP Role resolution protocol encountered an unknown value

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_PEER_INSTANCE_ERROR

3-Error

Instance:[dec] Peer:[dec] Up:[dec] Valid:[dec] Switch:[dec] Role:[chars] PeerRole:[chars]: [chars]

An error occured pertaining the instance and peer group specified

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_SLOT_PORT_ERR

3-Error

Slot:[dec] Port:[dec]: [chars]

RRP detected an error related to a slot and port

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_PEER_SUP_PSLOT_ERR

3-Error

save_rrp_tlv_data->peer_sup_pslot:[dec] my_sup_pslot:[dec]

RRP detected difference in peer supervisor pslot

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_SESSION_ID_ERR

3-Error

Instance:[dec] Peer:[dec]: Session id mismatch. Expected [dec] got [dec]

VSLP Role Resolution protocol detected an session id mismatch

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-RRP_RESERVED_PEER_ERR

3-Error

Instance:[dec] Peer:[dec]: Reserved peer [dec] [chars]

RRP detected an error related to reserved peer

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_PREEMPT

5-Notice

[chars] \n\tSwitch [dec]: Priority [dec]: Preempt [chars]\n \tSwitch [dec]: Priority [dec]: Preempt [chars]\n

Display preemption configuration

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-5-RRP_PREEMPT_IGNORE

5-Notice

[chars]

Ignore preemption configuration due to unsaved configs

cat6k-vs-infra

LOG_STD_NO_ACTION

VSLP-3-PKT_CREATE

3-Error

Can't create packet: [chars]

VSLP packet can't be created due to the reason described

vslp

LOG_STD_NO_ACTION

VSLP-3-PKT_TX

3-Error

Can't send packet: [chars]

VSLP packet can't be sent due to the reason described

vslp

LOG_STD_NO_ACTION

VSLP-3-PKT_RX

3-Error

Can't process the received packet: [chars]

VSLP packet can't be processed due to the reason described

vslp

LOG_STD_NO_ACTION

VSLP-3-PKT

3-Error

VSLP packet error: [chars]

VSLP packet error for the reason described

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_INST_OUT_OF_RANGE_CREATE

3-Error

Cannot create VSLP instance [dec]

Unable to create a VSLP instance for the switch id since it is not within the acceptable range

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_INST_OUT_OF_RANGE_DESTROY

3-Error

Cannot destroy VSLP instance [dec]

Unable to destroy the given VSLP instance since it is not witihn the acceptable range

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_INST_INVALID_CAP

3-Error

Invalid capability [dec] for VSLP instance [dec]

A VSLP capability was requested that is beyond the current list of supported capabilities

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_REGISTRY_ADD_FAIL

3-Error

[chars] registry addition failed

Failed to add to the the given registry during initialization

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_NULL_ENTRY

3-Error

Null [chars] entry in [chars] operation

A NULL entry was passed in the specified operation

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_PROC_CREATE_FAILED

3-Error

Unable to create process \[chars]\

Unable to create the specified process because of unknown reasons

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_QUEUE_CREATE_FAILED

3-Error

Unable to create watched queue \[chars]\

Unable to create the specified watched queue because of unknown reasons

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_BOOLEAN_CREATE_FAILED

3-Error

Unable to create watched boolean \[chars]\

Unable to create the specified watched boolean due to unknown reasons

vslp

LOG_STD_NO_ACTION

VSLP-6-ACTIVE

6-Information

[chars]

Informational messages regarding the state of the Virtual Switch active supervisor

vslp

LOG_STD_NO_ACTION

VSLP-6-STANDBY

6-Information

[chars]

Informational messages regarding the state of the Virtual Switch standby supervisor

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_MAX_PORTS

3-Error

Cannot configure more than [dec] ports

Unable to configure LMP on a port because the maximum number of ports per LMP instance has been reached

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_MAX_PGS

3-Error

Cannot create more thatn [dec] LMP peer groups

For some reason the number of LMP peer groups has reacehed the maximum per LMP instance

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_PG_OUT_OF_RANGE

3-Error

Peer group [dec] is out of range

A peer group has been passed to some API that is out of range

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_PG_NO_CTRL_LINK

3-Error

No control link for preferred PG [dec]

A peer group has been set as the preferred PG but it has no control link

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_FSM_TIMER_BAD_CTXT

3-Error

Invalid or NULL context for timer [dec] in [chars] operation

A timer event happened but the FSM infrastructure passed to the handler a context pointer that is currently not in use or is NULL

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_FSM_INVALID_TIMER

3-Error

Invalid timer [dec] for port [dec]/[dec] in [chars] operation

A timer event happened but the timer type was invalid

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_PG_CREATE_FAIL

3-Error

Unable to create PG [enet] for port [dec]/[dec]

-

-

-

VSLP-3-VSLP_LMP_PG_GET_FAIL

3-Error

Unable to get PG [enet] for port [dec]/[dec]

-

-

-

VSLP-3-VSLP_LMP_PG_INCONSISTENT

3-Error

PG [enet]:[dec] should have [dec] links but none found

A link has left a peer group that seems to have more links but none were found

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_FSM_NULL_CTXT

3-Error

NULL context for FSM action [chars]

An FSM action routine was invoked but with a NULL context argument

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_INVALID_PROC_EVENT

3-Error

Got event [dec]:[dec]

The process was woken up with an invalid event

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_RX_BAD_TLV_COUNT

3-Error

Bad TLV count in received packet [dec]

-

-

-

VSLP-3-VSLP_LMP_RX_BAD_INTERFACE

3-Error

Incorrect port [dec]/[dec] for received packet

An LMP packet was received that has incorrect received packet info. This could mean either that an LMP packet was received from an interface on which VSLP is not enabled. The packet was dropped

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_RX_BAD_FIRST_TLV

3-Error

Bad first TLV [dec] in received packet on port [dec]/[dec]

-

-

-

VSLP-3-VSLP_LMP_RX_PLATFORM_REJECT

3-Error

Platform TLV rejected for receieved [chars] packet

One or more platform TLVs were rejected in the received packet. The packet was dropped

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_RX_XFORM

3-Error

Failed to transform received [chars] packet

Failed to do ISSU transformation on the received packet. The packet was dropped

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_RX_QUEUE_FAIL

3-Error

Unable to enqueue received packet for processing

An internal error occurred that prevented a packet from being enqueued to the packet processing queue for processing. The packet was dropped

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_DOMAIN_MISMATCH

3-Error

Domain ID in probe packet from peer [dec] is not the same as local Domain ID [dec]. The packet was dropped.

Virtual switch domain id in probe packet from peer is not the same as the local domain id. The packet was dropped

vslp

"Investigate and correct this misconfiguration"

VSLP-3-VSLP_LMP_SAME_SWITCH_ID

3-Error

Switch id in probe packet is the same as the local switch id [dec]. The packet was dropped.

Switch id in probe packet from peer is the same as the local switch id. The packet was dropped

vslp

"Investigate and correct this misconfiguration"

VSLP-3-VSLP_LMP_FAIL_REASON

3-Error

[chars]: [chars]

This message gives the reason for a link to leave LMP operational state

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_THREAD_CREATE_FAILURE

3-Error

tid [dec]/intvl [dec]: [chars]

VSLP tx thread creation failed for the specified reason

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_THREAD_FAILURE

3-Error

tid [dec]: [chars]

General VSLP tx thread failure occurred for the specified reason

vslp

LOG_STD_NO_ACTION

VSLP-3-ISSU_ERROR

3-Error

[chars]

VSLP failed to do an ISSU operation

vslp

LOG_STD_NO_ACTION

VSLP-3-VSLP_LMP_FLAG_SET

3-Error

Incorrect flag value 0x[hec] on port [dec]/[dec]

This is an unexpected value for the flag field of a VSL link. This is due to an internal software error

vslp

"show vslp lmp summary and " "show vslp lmp fsm"

VSLP-4-VSL_PREEMPT_TIMER

4-Warning

Preempt timer configured to [dec] minutes. Standby will takeover as active in [dec] minutes

-

-

-

VSLP-5-VSL_UP

5-Notice

[chars]\n

VSL STATUS CHANGED to UP with more detail status

vsl

LOG_STD_NO_ACTION

VSLP-2-VSL_DOWN

2-Critical

[chars]\n

VSL STATUS CHANGED to DOWN with more detail status

vsl

LOG_STD_NO_ACTION

VSLP-4-ASIC_DUMP

4-Warning

[chars]

VSL physical link was up and role was not resolved in RRP

vsl

LOG_STD_NO_ACTION

ETC-4-NOMEM

4-Warning

Not enough memory available for [chars]

The PAgP/LACP Shim/EC could not obtain the memory it needed.

fec

LOG_STD_SH_TECH_ACTION

ETC-5-NOPAGP

5-Notice

Invalid EC mode PAgP not enabled

PAgP is not included in the image. Cannot set EC mode to desirable/auto

fec

"Get an image with PAgP included or set mode to On"

ETC-5-ERRPROT

5-Notice

Channel protocol mismatch for interface [chars] in group [dec]: the interface can not be added to the channel group

The interface can not be added to the channel-group with the specified mode

fec

"Change the channel-group or the mode for the " "interface"

ETC-5-ERRPROT2

5-Notice

Command rejected: the interface [chars] is already part of a channel with a different type of protocol enabled

The interface can not be selected for the specified protocol since is already part of a channel with a different type of protocol enabled

fec

"Remove the interface from the channel group"

ETC-5-ERRPROT3

5-Notice

Command rejected: the interface [chars] is already part of a channel

The interface can not be unselected for the specified protocol since is already part of a channel

fec

"Remove the interface from the channel group"

ETC-5-PORTDOWN

5-Notice

Shutting down [chars] as its port-channel is admin-down

The administrative state of the port is controlled by the administrative state of its aggregate port. If the administrative state of the aggregate port is down the administrative state of the port will also be forced to be down

fec

"Enter the <CmdBold>no shutdown<NoCmdBold> command " "on the aggregate port to activate unshut the "

ETC-5-DONTBNDL

5-Notice

[chars] suspended: incompatible remote port with [chars]

The configuration of the remote port is different from the configuration of other remote ports in the bundle. A port can only join the bundle when the configuration of the local port and the configuration of the remote port are the same as other ports already in the bundle.

fec

"Ensure that the configuration of the remote ports " "is the same for all ports in the bundle"

ETC-5-L3DONTBNDL1

5-Notice

[chars] suspended: PAgP not enabled on the remote port.

PAgP is enabled on an L3 interface but it has been detected that the remote port does not have PAgP enabled. In this mode the port is put in a suspended state.

fec

"Enable PAgP on remote side"

ETC-5-L3DONTBNDL2

5-Notice

[chars] suspended: LACP currently not enabled on the remote port.

LACP is enabled on an L3 interface but it has been detected that the remote port does not have LACP enabled. In this mode the port is put in a suspended state.

fec

"Enable LACP on the remote side"

ETC-5-STAYDOWN

5-Notice

[chars] will remain down as its port-channel [chars] is admin-down

The administrative state of the aggregation port overrides that of the port. If the aggregation port is administratively down all ports in the aggregation port will also be forced to be administratively down.

fec

"Enter the <CmdBold>no shutdown<NoCmdBold> command " "on the aggregation port to activate unshut the "

ETC-5-MINLINKS_NOTMET

5-Notice

Port-channel [chars] is down bundled ports [dec] doesn't meet min-links

The administrative configuration of minimum links is greater than the\n\ number of bundled ports. Therefore this port channel has been brought\n\ down

fec

"Reduce the min-links configuration for this group\n\ or add more ports to this port-channel to create a\n\ bundle."

ETC-5-MINLINKS_MET

5-Notice

Port-channel [chars] is up as its bundled ports [dec] meets min-links

The administrative configuration of minimum links is equal or less than the\n\ number of bundled ports. Therefore this port channel has been brought\n\ up

fec

"This is an informational message only.\n\ No action is required"

ETC-5-CANNOT_BUNDLE1

5-Notice

Port-channel [chars] is down port [chars] will remain stand-alone.

The state of the aggregation port is down. The port will remain\n\ stand-alone until the state of the aggregation port is up.

-

"Ensure that the other ports in the bundle have the\n\ same configuration."

ETC-5-CANNOT_BUNDLE2

5-Notice

[chars] is not compatible with [chars] and will be suspended [chars]

The attributes of the specified port are different from the attributes of the port-channel or the attributes of the ports within the port-channel.

-

"Match the attributes of the specifed port to the attributes of the " "port-channel so that the specified port can join the bundle".

ETC-5-CANNOT_BUNDLE_QOS

5-Notice

Removed [chars] from port channel because a QoS policy cannot be supported across multiple DFC cards.

The Port specified in the error message cannot join port channel because the QoS policy attached to the port channel cannot support multiple DFC cards.

fec

"Place the port in another port channel or remove " "the QoS policy from the port channel."

ETC-5-CANNOT_BUNDLE_QOS1

5-Notice

Removed [chars] from port channel as QoS attributes of port and port-channel are different.

The Port specified in the error message cannot join port channel because the QoS attributes of this port are not consistent with the QoS attributes of the port-channel.

fec

"Match the QoS attributes of the specified port to the QoS " "attributes of other member ports in the port channel. Use the " "<CmdBold>show queueing interface<NoCmdBold> command to display " "the QoS attributes of a port."

ETC-5-CANNOT_BUNDLE_LACP

5-Notice

[chars] is not compatible with aggregators in channel [dec] and cannot attach to them [chars]

The port has different port-attributes that of port-channel or ports within the port-channel. For the port to join the bundle change the ports attributes so that it matches the port.

-

"Match the port-attributes to that of port-channel"

ETC-5-UNSUITABLE

5-Notice

[chars] will not join any port-channel [chars]

Configuring any of Port-fast VMPS Dest-SPAN are considered unsuitable for etherchannel. Please unconfigure them.

-

-

ETC-5-BUNDLE

5-Notice

Interface [chars] joined port-channel [chars]

Interface joined the bundle.

-

-

ETC-5-UNBUNDLE

5-Notice

Interface [chars] left the port-channel [chars]

Interface fell off the bundle

-

-

ETC-5-CANNOT_ALLOCATE_AGGREGATOR

5-Notice

Aggregator limit reached cannot allocate aggregator for group [dec]

New aggregator cannot be allocated in the group. Change the port attributes of the ports in the group so that they match and join the same aggregator.

-

-

ETC-5-COMPATIBLE

5-Notice

[chars] is compatible with port-channel members

The specified port was not operational earlier because its attributes were different from the attributes of the port-channel or the attributes of the ports within the port-channel. The system detects that the attributes of the specified port now match the port-channel attributes.

-

LOG_STD_NO_ACTION

ETC-5-NOLACP

5-Notice

Invalid EC mode LACP not enabled

LACP is not included in the image. Cannot set EC mode to active/passive

fec

"Get an image with LACP included or set mode to On"

ETC-3-NULL_AG_UNKNOWN_GROUP

3-Error

The system does not find port-channel group information

The system is trying to retrieve the port-channel group information for a specific port channel but it cannot find it.

PF_DDTS_COMPONENT

LOG_STD_ACTION

PAGP_DUAL_ACTIVE-4-NO_CHNL_GROUP

4-Warning

Port [chars] channel group not present while [chars]

Extraction of the channel group from a link has failed but is expected to be present. This should not occur and may affect functionality depending on where it occurred.

cat6k-vs-infra

"This message should not be seen under normal operation. " "If it is appearing it is an indication of a software bug. " "Enter the commands:\n" "<CMDBOLD>show switch virtual dual-active summary<NOCMDBOLD>\n" "<CMDBOLD>show switch virtual dual-active pagp<NOCMDBOLD>\n" "Retrieve the PAgP packet contents by entering the commands:\n " "<CMDBOLD>debug condition interface <INTFC><NOCMDBOLD>\n" "<CMDBOLD>debug pagp packet<NOCMDBOLD>\n" "and " LOG_STD_SH_TECH_ACTION

PAGP_DUAL_ACTIVE-3-ADD_TLV_FAIL

3-Error

Too few bytes for [chars] TLV in PAgP reqd. [dec] got [dec] on port [chars]

-

-

-

PAGP_DUAL_ACTIVE-3-REGISTRY_ADD_ERR

3-Error

Failure in adding to [chars] registry

Could not add a function to the registry

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-1-RECOVERY

1-Alert

PAgP running on [chars] triggered dual-active recovery: active id [enet] received expected [enet] Switch is in recovery mode

Pagp detected dual-active scenario on specified interface and caused switch to go into recovery mode.

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-3-PROC_CREATE_FAILED

3-Error

Unable to create process \[chars]\

Unable to create the specified process

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-3-OBJECT_CREATE_FAILED

3-Error

Unable to create \[chars]\

Unable to create the specified managed object

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_DUAL_ACTIVE-3-RECOVERY_TRIGGER

3-Error

PAgP running on [chars] informing virtual switches of dual-active: new active id [enet] old id [enet]

Pagp received new active id on specified interface indicating virtual switches are in a dual-active scenario. Interface is informing virtual switches of this which will cause one switch to go into recovery mode.

cat6k-vs-infra

LOG_STD_NO_ACTION

PAGP_SWITCH_ISSU-2-INIT

2-Critical

PAGP SWITCH ISSU client initialization failed to [chars]. Error: [dec] [chars]

The PAGP SWITCH ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

L2

LOG_STD_ACTION

PAGP_SWITCH_ISSU-3-TRANSFORM_FAIL

3-Error

PAGP SWITCH ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The PAGP SWITCH ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the PAGP SWITCH state between the active device and the standby device is not identical.

L2

"show issu session <client_id> and " "show issu negotiated version <session_id>"

PAGP_SWITCH_ISSU-3-MSG_NOT_OK

3-Error

PAGP SWITCH ISSU client 'Message Type [dec]' is not compatible

The PAGP SWITCH ISSU client received an incompatible message from the peer device. The message cannot be processed.

L2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

PAGP_SWITCH_ISSU-3-MSG_SIZE

3-Error

PAGP SWITCH ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The PAGP SWITCH ISSU client failed to calculate the MTU for the specified message. The PAGP SWITCH ISSU client is not able to send the message to the standby device.

L2

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

PAGP_SWITCH_ISSU-3-INVALID_SESSION

3-Error

PAGP SWITCH ISSU client does not have a valid registered session.

The PAGP SWITCH ISSU client does not have a valid registered session.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-2-SESSION_REGISTRY

2-Critical

PAGP SWITCH ISSU client failed to register session information. Error: [dec] [chars]

The PAGP SWITCH ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-3-SESSION_UNREGISTRY

3-Error

PAGP SWITCH ISSU client failed to unregister session information. Error: [dec] [chars]

The PAGP SWITCH ISSU client failed to unregister session information.

L2

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-2-SESSION_NEGO

2-Critical

PAGP SWITCH ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The PAGP SWITCH ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

L2

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-2-SEND_NEGO_FAILED

2-Critical

PAGP SWITCH ISSU client failed to send negotiation message. Error: [dec] [chars]

The PAGP SWITCH ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

L2

"show logging and show checkpoint client"

PAGP_SWITCH_ISSU-2-SESSION_ARBITRATE

2-Critical

PAGP SWITCH ISSU client failed to register arbitrate callback. Error: [dec] [chars]

The PAGP SWITCH ISSU client failed to register arbitrate callback. If a problem occurs with the callback registration the standby device cannot be brought up properly.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-2-GET_BUFFER

2-Critical

PAGP SWITCH ISSU client failed to get buffer for message. Error: [dec] [chars]

PAGP SWITCH ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

L2

"show logging and show checkpoint client"

PAGP_SWITCH_ISSU-3-INVALID_CAPABILITY

3-Error

PAGP SWITCH ISSU client: invalid capability list

PAGP SWITCH ISSU client observed an error during capability negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-3-REJECTED_CAPABILITY

3-Error

PAGP SWITCH ISSU client rejected capability '[chars]'

PAGP SWITCH ISSU client rejected a capability during negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-3-REJECTING_CAPABILITY

3-Error

PAGP SWITCH ISSU client rejecting capability '[chars]'

PAGP SWITCH ISSU client is rejecting a capability during negotiaiton. When this error happens there is a mismatch in the client capability between the active and standby unit.

L2

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PAGP_SWITCH_ISSU-3-POLICY_NOT_SUPPORTED

3-Error

PAGP SWITCH ISSU client does not support Message Type [dec]

PAGP SWITCH ISSU client received an message type which it does not support. The policy is applied to make the session incompatible.

L2

"show issu session <client_id>"

IP_HOST_ISSU-2-INIT

2-Critical

IP Host ISSU client initialization failed to [chars]. Error: [dec] [chars]

The IP Host ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

-

LOG_STD_ACTION

IP_HOST_ISSU-3-TRANSFORM_FAIL

3-Error

IP Host ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The IP Host ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the IP Host state between the active device and the standby device is not identical.

-

"show issu session <client_id> and " "show issu negotiated version <session_id>"

IP_HOST_ISSU-3-MSG_NOT_OK

3-Error

IP Host ISSU client 'Message Type [dec]' is not compatible

The IP Host ISSU client received an incompatible message from the peer device. The message cannot be processed.

-

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

IP_HOST_ISSU-3-MSG_SIZE

3-Error

IP Host ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The IP Host ISSU client failed to calculate the MTU for the specified message. The IP Host ISSU client is not able to send the message to the standby device.

-

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

IP_HOST_ISSU-3-INVALID_SESSION

3-Error

IP Host ISSU client does not have a valid registered session.

The IP Host ISSU client does not have a valid registered session.

-

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

IP_HOST_ISSU-2-SESSION_REGISTRY

2-Critical

IP Host ISSU client failed to register session information. Error: [dec] [chars]

The IP Host ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

-

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

IP_HOST_ISSU-3-SESSION_UNREGISTRY

3-Error

IP Host ISSU client failed to unregister session information. Error: [dec] [chars]

The IP Host ISSU client failed to unregister session information.

-

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IP_HOST_ISSU-2-SESSION_NEGO

2-Critical

IP Host ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The IP Host ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

-

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IP_HOST_ISSU-2-SEND_NEGO_FAILED

2-Critical

IP Host ISSU client failed to send negotiation message. Error: [dec] [chars]

The IP Host ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

-

"show logging and show checkpoint client"

IP_HOST_ISSU-2-GET_BUFFER

2-Critical

IP Host ISSU client failed to get buffer for message. Error: [dec] [chars]

The IP Host ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

-

"show logging and show checkpoint client"

IP_HOST_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

IP Host ISSU client capability exchange result incompatible.

The IP Host ISSU client capability exchange have negotiated as incompatible with the peer.

-

"show issu negotiated capability <Session_ID>"

IP_HOST_ISSU-3-CAP_INVALID_SIZE

3-Error

IP_HOST ISSU client capability list is empty.

The IP_HOST ISSU client capability exchange list size is invalid.

-

"show issu capability entires <Client_ID>"

IP_DEVICE_TRACKING-4-TABLE_LOCK_FAILED

4-Warning

Table already locked by process-id [dec][chars]

The IP device tracking table could not be updated due to a lock held by another process

-

LOG_STD_NO_ACTION

IP_DEVICE_TRACKING_HA-4-ENTRY_OUT_OF_SYNC

4-Warning

Host mac-address [enet] ip-address [inet] interface [chars] event_type: [chars] entry_type: [chars]

An inconsistency has been detected in the IP device tracking table for this host between active and standby

-

LOG_STD_NO_ACTION

IP_DEVICE_TRACKING_HA-3-FAIL_SEND_MSG_TO_ACTIVE

3-Error

Failed to send [chars] message to active for [chars] [chars]

The specified synchronization message which is an internal IPC message could not be sent to the active unit in the specified run-time module. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

-

LOG_STD_SH_TECH_ACTION

IP_DEVICE_TRACKING_HA-3-NO_RESOURCES

3-Error

[chars]

A run-time module could not obtain the resources that are required to complete a task. The failure most likely occurred because of a software error or a lack of system memory. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized.

-

"If you determine that this condition was caused by " "a lack of system memory reduce system activity to " "ease memory demands or if conditions warrant upgrade " "to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION

MAC_LIMIT-4-VLAN_EXCEED

4-Warning

Vlan [dec] with configured limit %ld has currently %ld entries

The Number of entries for a vlan has exceeded the\n\ allowed number

l2

"Depends of the Network admin"

MAC_LIMIT-4-VLAN_DROP

4-Warning

Vlan [dec] with configured limit %ld has currently %ld entries

The Number of entries for a vlan has gone below or\n\ is equal to the allowed number

l2

"Depends of the Network admin"

MAC_LIMIT-4-VLAN_ENFORCE

4-Warning

Enforcing limit on Vlan [dec] with configured limit %ld

The Number of entries for a vlan has exceeded the\n\ allowed number and the enforce to limit action is configured

l2

"Depends of the Network admin"

MAC_LIMIT-4-PORT_EXCEED

4-Warning

[chars] with configured limit %ld has currently %ld entries

The Number of entries for the port has exceeded the\n\ allowed number

l2

"Depends of the Network admin"

MAC_LIMIT-4-PORT_DROP

4-Warning

[chars] with Configured limit %ld has currently %ld entries

The Number of entries for the port has gone below or\n\ is equal to the allowed number

l2

"Depends of the Network admin"

MAC_LIMIT-4-PORT_ENFORCE

4-Warning

Enforcing limit on [chars] with Configured limit %ld

The Number of entries for the port has exceeded the\n\ allowed number and the enforce to limit action is configured

l2

"Depends of the Network admin"

MLD_SNOOP_ISSU-2-INIT

2-Critical

MLD Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MLD Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

mld-snooping

LOG_STD_ACTION

MLD_SNOOP_ISSU-3-TRANSFORM_FAIL

3-Error

MLD Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MLD Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MLD Snooping state between the active device and the standby device is not identical.

mld-snooping

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MLD_SNOOP_ISSU-3-MSG_NOT_OK

3-Error

MLD Snooping ISSU client 'Message Type [dec]' is not compatible

The MLD Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed.

mld-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MLD_SNOOP_ISSU-3-MSG_SIZE

3-Error

MLD Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MLD Snooping ISSU client failed to calculate the MTU for the specified message. The MLD Snooping ISSU client is not able to send the message to the standby device.

mld-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MLD_SNOOP_ISSU-3-INVALID_SESSION

3-Error

MLD Snooping ISSU client does not have a valid registered session.

The MLD Snooping ISSU client does not have a valid registered session.

mld-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-2-SESSION_REGISTRY

2-Critical

MLD Snooping ISSU client failed to register session information. Error: [dec] [chars]

The MLD Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

mld-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-3-SESSION_UNREGISTRY

3-Error

MLD Snooping ISSU client failed to unregister session information. Error: [dec] [chars]

The MLD Snooping ISSU client failed to unregister session information.

mld-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-2-SESSION_NEGO

2-Critical

MLD Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MLD Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mld-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-2-SEND_NEGO_FAILED

2-Critical

MLD Snooping ISSU client failed to send negotiation message. Error: [dec] [chars]

The MLD Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mld-snooping

"show logging and show checkpoint client"

MLD_SNOOP_ISSU-2-GET_BUFFER

2-Critical

MLD Snooping ISSU client failed to get buffer for message. Error: [dec] [chars]

The MLD Snooping ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mld-snooping

"show logging and show checkpoint client"

MVR_ISSU-2-INIT

2-Critical

MVR ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MVR ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

mvr

LOG_STD_ACTION

MVR_ISSU-3-TRANSFORM_FAIL

3-Error

MVR ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MVR ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MVR state between the active device and the standby device is not identical.

mvr

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MVR_ISSU-3-MSG_NOT_OK

3-Error

MVR ISSU client 'Message Type [dec]' is not compatible

The MVR ISSU client received an incompatible message from the peer device. The message cannot be processed.

mvr

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MVR_ISSU-3-MSG_SIZE

3-Error

MVR ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MVR ISSU client failed to calculate the MTU for the specified message. The MVR ISSU client is not able to send the message to the standby device.

mvr

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MVR_ISSU-3-INVALID_SESSION

3-Error

MVR ISSU client does not have a valid registered session.

The MVR ISSU client does not have a valid registered session.

mvr

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-2-SESSION_REGISTRY

2-Critical

MVR ISSU client failed to register session information. Error: [dec] [chars]

The MVR ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

mvr

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-3-SESSION_UNREGISTRY

3-Error

MVR ISSU client failed to unregister session information. Error: [dec] [chars]

The MVR ISSU client failed to unregister session information.

mvr

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-2-SESSION_NEGO

2-Critical

MVR ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MVR ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvr

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-2-SEND_NEGO_FAILED

2-Critical

MVR ISSU client failed to send negotiation message. Error: [dec] [chars]

The MVR ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvr

"show logging and show checkpoint client"

MVR_ISSU-2-GET_BUFFER

2-Critical

MVR ISSU client failed to get buffer for message. Error: [dec] [chars]

The MVR ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvr

"show logging and show checkpoint client"

L2MC_QUERIER-4-SNOOPING_DISABLED

4-Warning

The [chars] querier is operationally disabled in VLAN [dec] because [chars] snooping has been disabled in this VLAN.

IGMP/MLD snooping has been detected as being disabled on this VLAN. The IGMP/MLD querier function should not be operationally enabled when IGMP/MLD snooping is disabled.

l2mcast

"Ensure that IGMP/MLD snooping is enabled globally and on the VLAN " "reported. "

L2MC_QUERIER-6-SNOOPING_ENABLED

6-Information

The [chars] querier is now operationally enabled in VLAN [dec] because [chars] snooping is no longer disabled.

IGMP/MLD snooping has now been enabled and as a result the IGMP/MLD querier function has now been enabled.

l2mcast

"No action is required."

L2MC_QUERIER-4-PIM_ENABLED

4-Warning

The [chars] querier is operationally disabled in VLAN [dec] because PIM has been enabled on the SVI.

PIM has been detected on the SVI. The IGMP/MLD querier function should not be operationally enabled when PIM is enabled on the SVI.

l2mcast

"Ensure that PIM is disabled on the SVI. "

L2MC_QUERIER-6-PIM_DISABLED

6-Information

The [chars] querier is now operationally enabled in VLAN [dec] because PIM is no longer enabled on the SVI.

PIM has been disabled on the SVI and as a result the IGMP/MLD querier function has now been enabled.

l2mcast

"No action is required."

L2MC_QUERIER-4-NO_IP_ADDR_CFG

4-Warning

The [chars] querier cannot send out General Query messages in VLAN [dec] because there is no IP address configured on the system.

The allocation of explicit-tracking entries is bounded to avoid\n\ the IGMP/MLD snooping hogs the system resources

igmp/mld snooping

"Disable and re-enable L2 multicast snooping on the VLAN."

IGMP_SNOOP_ISSU-2-INIT

2-Critical

IGMP Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars]

The IGMP Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

igmp-snooping

LOG_STD_ACTION

IGMP_SNOOP_ISSU-3-TRANSFORM_FAIL

3-Error

IGMP Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The IGMP Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the IGMP Snooping state between the active device and the standby device is not identical.

igmp-snooping

"show issu session <client_id> and " "show issu negotiated version <session_id>"

IGMP_SNOOP_ISSU-3-MSG_NOT_OK

3-Error

IGMP Snooping ISSU client 'Message Type [dec]' is not compatible

The IGMP Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed.

igmp-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

IGMP_SNOOP_ISSU-3-MSG_SIZE

3-Error

IGMP Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to calculate the MTU for the specified message. The IGMP Snooping ISSU client is not able to send the message to the standby device.

igmp-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

IGMP_SNOOP_ISSU-3-INVALID_SESSION

3-Error

IGMP Snooping ISSU client does not have a valid registered session.

The IGMP Snooping ISSU client does not have a valid registered session.

igmp-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-2-SESSION_REGISTRY

2-Critical

IGMP Snooping ISSU client failed to register session information. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

igmp-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-3-SESSION_UNREGISTRY

3-Error

IGMP Snooping ISSU client failed to unregister session information. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to unregister session information.

igmp-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-2-SESSION_NEGO

2-Critical

IGMP Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The IGMP Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

igmp-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-2-SEND_NEGO_FAILED

2-Critical

IGMP Snooping ISSU client failed to send negotiation message. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

igmp-snooping

"show logging and show checkpoint client"

IGMP_SNOOP_ISSU-2-GET_BUFFER

2-Critical

IGMP Snooping ISSU client failed to get buffer for message. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

igmp-snooping

"show logging and show checkpoint client"

SW_DAI-4-INVALID_ARP

4-Warning

%ld Invalid ARPs [chars] on [chars] vlan [dec].[[enet]/[chars]/[enet]/[chars]/[clock]]

The switch has received ARP packets considered invalid by ARP inspection.\n\ The packets are bogus and they do not pass one or more of source mac or \n\ destination mac or IP validation checks or are otherwise invalid.

arp-inspection

LOG_STD_NO_ACTION

SW_DAI-4-ACL_DENY

4-Warning

%ld Invalid ARPs [chars] on [chars] vlan [dec].[[enet]/[chars]/[enet]/[chars]/[clock]]

-

arp-inspection

LOG_STD_NO_ACTION

SW_DAI-4-DHCP_SNOOPING_DENY

4-Warning

%ld Invalid ARPs [chars] on [chars] vlan [dec].[[enet]/[chars]/[enet]/[chars]/[clock]]

The switch has received ARP packets considered invalid by ARP inspection.\n\ The packets are bogus and their presence may be an indication of \n\ man-in-the-middle attacks being attempted in the network. This message\n\ is logged when the senders ip and mac binding for the received vlan \n\ is not present in the dhcp snooping database.

arp-inspection

LOG_STD_NO_ACTION

SW_DAI-6-ACL_PERMIT

6-Information

%ld ARPs [chars] on [chars] vlan [dec].[[enet]/[chars]/[enet]/[chars]/[clock]]

The switch has received ARP packets that have been permitted as a\n\ result of ACL match.

arp-inspection

LOG_STD_NO_ACTION

SW_DAI-6-DHCP_SNOOPING_PERMIT

6-Information

%ld ARPs [chars] on [chars] vlan [dec].[[enet]/[chars]/[enet]/[chars]/[clock]]

The switch has received ARP packets that have been permitted as a\n\ result of senders IP and MAC address match against the dhcp snooping\n\ database for the received vlan.

arp-inspection

LOG_STD_NO_ACTION

SW_DAI-6-ARP_PROBE_PERMIT

6-Information

%ld ARPs [chars] on [chars] vlan [dec].[[enet]/[inet]/[enet]/[inet]/[clock]]

This message is logged when an ARP packet with a sender IP address of 0.0.0.0 has been permitted. These packets are used as ARP probes by various network devices. These messages are not logged by default but only when arp-probe logging is enabled.

arp-inspection

LOG_STD_NO_ACTION

SW_DAI-4-SPECIAL_LOG_ENTRY

4-Warning

%ld Invalid ARP packets [[clock]]

The switch has received ARP packets considered invalid by ARP inspection.\n\ The packets are bogus and their presence may be an indication of \n\ man-in-the-middle attacks being attempted in the network.\n\ This message differs from other messages in that while the other\n\ can be used to provide as much information of the packet as possible\n\ this message is used as a catch all message when the rate of incoming\n\ packets exceed DAI logging rate.

arp-inspection

LOT_STD_NO_ACTION

SW_DAI-4-PACKET_RATE_EXCEEDED

4-Warning

[dec] packets received in [dec] milliseconds on [chars].

The switch has received the given number of ARP packets in the given\n\ duration on the given interface. This message is logged just before \n\ the port is err-disabled because of exceeded packet rate. And this\n\ message is logged when the burst interval is set to 1 second.

arp-inspection

LOT_STD_NO_ACTION

SW_DAI-4-PACKET_BURST_RATE_EXCEEDED

4-Warning

[dec] packets received in [dec] seconds on [chars].

The switch has received the given number of ARP packets in the specified\n\ burst interval. The interface is errdisabled when the switch receives\n\ packets at a rate higher than the configured packet rate every second \n\ over the configured burst interval. The message is logged just before\n\ the interface is err-disabled and if the configured burst interval is\n\ more than a second.

arp-inspection

LOT_STD_NO_ACTION

ILPOWER-3-ILPOWER_INTERNAL_IF_ERROR

3-Error

Inline Power internal error interface [chars]: [chars]

A software check failed during Power over Ethernet PoE processing.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-5-ILPOWER_POWER_DENY

5-Notice

Interface [chars]: inline power denied. Reason: [chars]

There is not enough power remaining in the switch to supply to\n\ the Power over Ethernet PoE port.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-ILPOWER_POWER_CDP_SHUT

5-Notice

Interface [chars]: inline power shut

-

inline-power

LOG_STD_NO_ACTION

ILPOWER-3-CONTROLLER_ERR

3-Error

Controller error Controller number [dec]: [chars]

An error reported or caused by the Power over Ethernet PoE controller is detected.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-3-CONTROLLER_POST_ERR

3-Error

Inline Power Feature is disabled on this switch because\n\ Power On Self Test POST failed on this switch.\n\msgdef_explanation An error reported or caused by the Power over Ethernet

-

-

-

ILPOWER-3-CONTROLLER_IF_ERR

3-Error

Controller interface error [chars]: [chars]

An interface error is detected between the Power over Ethernet PoE controller and system.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-3-CONTROLLER_PORT_ERR

3-Error

Controller port error Interface [chars]: [chars]

A port error reported by the Power over Ethernet PoE controller is detected.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-5-POWER_GRANTED

5-Notice

Interface [chars]: Power granted

There is enough power available in the switch and\n\ the switch is providing power on the interface.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-LINKDOWN_DISCONNECT

5-Notice

Interface [chars]: Link down disconnect

The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-IEEE_DISCONNECT

5-Notice

Interface [chars]: PD removed

The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-DETECT

5-Notice

Interface [chars]: Power Device detected: [chars]

The switch has detected the attached power device.

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-INVALID_IEEE_CLASS

5-Notice

Interface [chars]: has detected invalid IEEE class: [dec] device. Power denied

The power device has invalid IEEE class. switch won't power\n\up the device

-

LOG_STD_NO_ACTION

ILPOWER-3-SHUT_OVERDRAWN

3-Error

Interface [chars] is shutdown as it is consuming more than the maximum configured power [dec] milliwatts.

Interface is shutdown because it is consuming more than the maximum configured power

inline-power

"Make sure correct power is budgeted for this interfac\n\e based on the power device electrical specifications or ratings. It is recommended to change the police cutoff power to a higher value to keep the device powered on"

ILPOWER-4-LOG_OVERDRAWN

4-Warning

Interface [chars] is overdrawing power. it is consuming [dec] milliwatts where as maximum configured power is [dec] milliwatts.

-

inline-power

"Make sure correct power is budgeted for this interface based on the power device electrical specifications or ratings. Otherwise you might risk overloading the switch. It is recommended to change the police cutoffpower appropriately if needed"

ILPOWER-5-CLR_OVERDRAWN

5-Notice

Interface [chars] is NOT overdrawing power. it is consuming [dec] milliwatts where as maximum configured value is [dec] milliwatts.

-

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-POLICE_POWER_INVALID

5-Notice

Interface [chars]: invalid power police [dec] milliwatts current [dec] mA voltage [dec] mV

power policing current or voltage value is invalid.

-

LOG_STD_SH_TECH_ACTION

ILPOWER-5-SENSE_POWER_INVALID

5-Notice

Interface [chars]: invalid power sense [dec] milliwatts current [dec] mA voltage [dec] mV

power sensing current or voltage value is invalid.

inline-power

LOG_STD_SH_TECH_ACTION

ILPOWER-4-ILPOWER_POWER_SUPPLY

4-Warning

PoE Power Supply [chars]: [chars]

The power supply for PoE is OIR

inline-power

"Make sure power supply to PoE input is inserted after removal"

ILPOWER-4-ILPOWER_PS_ABSENCE

4-Warning

PoE module Power Supply not present \n\ Inline Power Feature is disabled on [chars] because Power On Self Test POST failed \n : [chars]

The power supply for PoE expansion module is not present or not inserted properly or faulty

inline-power

"Make sure power supply to expansion module is inserted properly\ and reload the switch with PoE power supply present"

ILPOWER-4-WARNING

4-Warning

Power-over-Ethernet is disabled on this switch \n\ PoE functionality requires a power input of 44 to 57 Volts DC

The power supply voltage is NOT in range 44 V-57 V to support PoE/PoE+

inline-power

"Make sure the power supply Voltage is in range 44 V-57 V if intend to use PoE/PoE+"

ILPOWER-5-PWRGOOD_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power good

Spare pair power request was successful and power is available on spare pair

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-TSTART_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power error: TSTART

spare pair tstart error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-PGOOD_TIMEOUT_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power good timeout error

spare pair power good timeout error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-DET_SHORT_SPARE_PAIR

5-Notice

Interface [chars]: spare pair short detected

spare pair short detect error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-DET_TIMEOUT_SPARE_PAIR

5-Notice

Interface [chars]: spare pair detect timeout

spare pair timeout detect error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-6-SET_ILPOWER

6-Information

Set power allocated to POE to [dec] for slot [dec]

The power allocated to POE has changed

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-SINGLE_PAIRSET_FAULT

5-Notice

Interface [chars]: shutting down [chars] pairset due to [chars] fault

The dual signature PD on this port has hit a critcal fault on one pairset and hence that pairset will be shutdown

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-LLDP_SHUTDOWN

5-Notice

Interface [chars]: PD requested shutdown for [dec] sec via LLDP MDI TLV

Inline power is removed because \n\ PD requested shutdown via LLDP MDI TLV

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-IMAX_SPARE_PAIR

5-Notice

Interface [chars]: spare pair power error: IMAX

spare pair imax error has occurred power on spare pair will not be supplied

inline-power

LOG_STD_NO_ACTION

ILPOWER-5-PD_ENTRY_REMOVAL

5-Notice

Interface [chars]: power device entry removed admin_state=[chars] oper_state=[chars]

received power device removal event from controller

inline-power

LOG_STD_NO_ACTION

ILPOWER-2-PRIO_CRIT_LIMIT

2-Critical

Priority [dec] reached critical limit. Load shedding can lead to chassis reload. Please avoid configuring any more ports at this priority level. Maximum interface power is used for this calculation.

This priority level reached maximum allowed wattage

inline-power

"Please distribute ports to another priority"

ILPOWER-2-PRIO_CRIT_LIMIT_SVL

2-Critical

On Chassis [dec] priority [dec] reached critical limit. Load shedding can lead to chassis reload. Please avoid configuring any more ports at this priority level. Maximum interface power is used for this calculation.

This priority level reached maximum allowed wattage

inline-power

"Please distribute ports to another priority"

ILPOWER-4-PRIO_WARN_LIMIT

4-Warning

Priority [dec] is reaching critical limit. Maximum interface power is used for this calculation.

This priority level reached warning limit wattage

inline-power

"Please don't configure any more ports " "at this priority."

ILPOWER-4-PRIO_WARN_LIMIT_SVL

4-Warning

On Chassis [dec] priority [dec] is reaching critical limit. Maximum interface power is used for this calculation.

This priority level reached warning limit wattage

inline-power

"Please don't configure any more ports at this priority"

ILPOWER-5-PD_POWER_DEMOTE

5-Notice

Interface [chars] requested power=[dec]w hardware limit=[dec]w

Requested power is greater than the hardware limit

inline-power

LOG_STD_NO_ACTION

ILPOWER_ISSU-3-INIT

3-Error

Inline power ISSU client initialization failed to [chars].Error: [dec] [chars]

Inline power ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

ilpower

LOG_STD_SH_TECH_ACTION

ILPOWER_ISSU-3-TRANSFORM_FAIL

3-Error

Inline power ISSU client [chars] transform failed for message type [dec].\n\ Error: [dec] [chars]

Inline power ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Inline power state will not\n\ be indentical with the active unit.

ilpower

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

ILPOWER_ISSU-3-MSG_NOT_OK

3-Error

Inline power ISSU client message type [dec] is not compatible

Inline power ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it cannot be processed by this unit

ilpower

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

ILPOWER_ISSU-3-MSG_SIZE

3-Error

Inline power ISSU client failed to get the MTU for message type [dec].\n\ Error: [dec] [chars]

Inline power ISSU client failed to calculate MTU\n\ for the message specified. The dot1x ISSU client will not\n\ be able to send message to the standby unit.

ilpower

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

ILPOWER_ISSU-3-INVALID_SESSION

3-Error

Inline power ISSU client does not have a valid registered session.

Inline power ISSU client does not have a valid registered session.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up.

ilpower

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

ILPOWER_ISSU-3-SESSION_REGISTRY

3-Error

Inline power ISSU client failed to register session information.\n\ Error: [dec] [chars]

Inline power ISSU client failed to register session information.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up.

ilpower

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

ILPOWER_ISSU-3-SESSION_UNREGISTRY

3-Error

Inline power ISSU client failed to unregister session information.\n\ Error: [dec] [chars]

Inline power ISSU client failed to unregister session information.

ilpower

"show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

ILPOWER_ISSU-3-SESSION_NEGO

3-Error

Inline power ISSU client encountered unexpected client nego_done.\n\ Error: [dec] [chars]

Inline power ISSU client encountered an unexpected 'client\n\ negotiation done'.

ilpower

"show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

ILPOWER_ISSU-3-SEND_NEGO_FAILED

3-Error

Inline power ISSU client failed to send negotiation message.\n\ Error: [dec] [chars]

Inline power ISSU client failed to send a session negotiation\n\ message to the peer. When there is a problem in the ISSU\n\ negotiation the standby unit can not be brought up.

ilpower

"show logging and show checkpoint client"

ILPOWER_ISSU-3-GET_BUFFER

3-Error

Inline power ISSU client failed to get buffer for message.\n\ Error: [dec] [chars]

Inline power ISSU client failed to get buffer for building\n\ a negotiation message. Hence it cannot send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

ilpower

"show logging and show checkpoint client"

ILP_ISSU-3-INIT

3-Error

Platform Inline Power ISSU client initialization failed at [chars] error [chars]

Platform ILP ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

platform-ha

LOG_STD_SH_TECH_ACTION

ILP_ISSU-3-TRANSFORM

3-Error

Platform Inline Power ISSU client [chars] transform failed error [chars]

Platform Inline Power ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Platform Inline Power state will not\n\ be indentical with the active unit.

platform-ha

"show issu session <client_id> and\n\ show issu negotiated version <session_id>"

ILP_ISSU-3-MSG_NOT_OK

3-Error

Platform Inline Power ISSU client message [dec] is not compatible

Platform Inline Power ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

ILP_ISSU-3-MSG_SIZE

3-Error

Platform Inline Power ISSU client failed to get the message size for message [dec]

Platform Inline Power ISSU client failed to calculate message size\n\ for the message specified. The Platform ILPower ISSU client will not\n\ be able to send message to the standby unit.

platform-ha

"show issu message group <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated version <session_id>"

ILP_ISSU-3-SESSION

3-Error

Platform ILPower ISSU client [chars]

Platform Inline Power ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

ILP_ISSU-3-SESSION_UNREGISTRY

3-Error

Platform ILPower ISSU client failed to unregister session information. Error: [dec] [chars]

The Platform Inline Power ISSU client failed to unregister session information.

platform-ha

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ILP_ISSU-3-SEND_FAILED

3-Error

Platform Inline Power ISSU client failed to send a negotiation message error [dec]

Platform ILPower ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

ILP_ISSU-3-BUFFER

3-Error

Platform ILPower ISSU client failed to get buffer for msg error [dec]

Platform Inline Power ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

platform-ha

"show logging and show checkpoint client"

ILP_ISSU-3-CAPABILITY

3-Error

Platform Inline Power ISSU client [chars]

Platform Inline Power ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

platform-ha

"show issu capability entries <client_id> and\n\ show issu session <client_id> and\n\ show issu negotiated capability <session_id>"

ILP_ISSU-3-POLICY

3-Error

Platform Inline Power ISSU client message type [dec] is [chars]

Platform Inline Power ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

platform-ha

"show issu session <client_id>"

ILP_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

Platform Inline Power ISSU client capability exchange result incompatible.

The Platform ILPower ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

platform-ha

"show issu negotiated capability <Session_ID>"

ILP_ISSU-3-CAP_INVALID_SIZE

3-Error

Platform Inline Power ISSU client capability list is empty.

The Platform Inline Power ISSU client capability exchange list size\n\ is invalid.

platform-ha

"show issu capability entries <Client_ID>"

DOT1X_SWITCH-4-PROC_START_ERR

4-Warning

Unable to start dot1x switch process.

The system failed to create the Dot1x switch process.

-

"Reload the device"

DOT1X_SWITCH-5-ERR_VLAN_NOT_FOUND

5-Notice

Attempt to assign non-existent or shutdown VLAN [chars] to 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a VLAN to an 802.1x port but the VLAN was not found in the VTP database.

-

"Make sure the VLAN exists and is not shutdown or use another VLAN."

DOT1X_SWITCH-5-ERR_VLAN_RSPAN

5-Notice

Attempt to assign RSPAN VLAN [chars] to 802.1x port [chars]. 802.1x is incompatible with RSPAN AuditSessionID [chars]

An attempt was made to assign a Remote SPAN VLAN to an 802.1x port. Remote SPAN should not be enabled on a VLAN in which ports are configured with 802.1x enabled.

-

"Either disable Remote SPAN configuration on the VLAN OR disable " "802.1x on all the ports in this VLAN."

DOT1X_SWITCH-5-ERR_VLAN_EQ_VVLAN

5-Notice

Data VLAN [chars] on port [chars] cannot be equivalent to the Voice VLAN AuditSessionID [chars]

An attempt was made to assign a data VLAN to an 802.1x port that is the same as the voice VLAN.

-

"Change either the Voice VLAN or the access/802.1x assigned VLAN on " "the interface so they are not equal anymore. This will cause the " "authentication to proceed normally on the next retry."

DOT1X_SWITCH-5-ERR_VLAN_INTERNAL

5-Notice

Attempt to assign internal VLAN [chars] to 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign an invalid VLAN to an 802.1x port. The VLAN specified is used internally and cannot be assigned to this port.

-

"Update the configuration not to use this VLAN."

DOT1X_SWITCH-5-ERR_VLAN_RESERVED

5-Notice

Attempt to assign reserved VLAN [chars] to 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign an invalid VLAN to an 802.1x port. The VLAN specified is a reserved VLAN and cannot be assigned to this port.

-

"Update the configuration not to use this VLAN."

DOT1X_SWITCH-5-ERR_VLAN_INVALID

5-Notice

Attempt to assign invalid VLAN [chars] to 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign an invalid VLAN to an 802.1x port. The VLAN specified is out of range and cannot be assigned to this port.

-

"Update the configuration to use a valid VLAN."

DOT1X_SWITCH-5-ERR_INVALID_SEC_VLAN

5-Notice

Attempt to assign invalid secondary VLAN [chars] to PVLAN host 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a non-secondary VLAN to a PVLAN host 802.1x port.

-

"Change the mode of the port so that it is no longer a PVLAN host " "port or use a valid secondary VLAN."

DOT1X_SWITCH-5-ERR_INVALID_PRIMARY_VLAN

5-Notice

Attempt to assign primary VLAN [chars] to 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a primary VLAN to an 802.1x port which is not allowed.

-

"Update the configuration to use a different VLAN."

DOT1X_SWITCH-5-ERR_PRIMARY_VLAN_NOT_FOUND

5-Notice

Attempt to assign VLAN [chars] whose primary VLAN does not exist or is shutdown to 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a private VLAN whose primary VLAN does not exist or is shutdown.

-

"Make sure the primary VLAN exists and is not shutdown. Also verify that " "the private VLAN is associated with a primary VLAN."

DOT1X_SWITCH-5-ERR_VLAN_ON_ROUTED_PORT

5-Notice

Attempt to assign VLAN [chars] to routed 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a VLAN to a routed 802.1x port which is not allowed.

-

"Change the mode of the port so that it is no longer a routed port " "or change the configuration so that no VLAN is assigned."

DOT1X_SWITCH-5-ERR_VLAN_PROMISC_PORT

5-Notice

Attempt to assign VLAN [chars] to promiscuous 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a VLAN to a promiscuous 802.1x port which is not allowed.

-

"Change the mode of the port so that it is no longer a promiscuous port " "or change the configuration so that no VLAN is assigned."

DOT1X_SWITCH-5-ERR_SEC_VLAN_INVALID

5-Notice

Attempt to assign secondary VLAN [chars] to non-PVLAN host 802.1x port [chars] AuditSessionID [chars]

An attempt was made to assign a secondary VLAN to a port that is not a PVLAN host port which is not allowed.

-

"Change the mode of the port so that it is configured as a PVLAN host " "port or use a different VLAN that is not configured as a secondary " "VLAN."

DOT1X_SWITCH-5-ERR_SPAN_DST_PORT

5-Notice

Attempt to assign VLAN [chars] to 802.1x port [chars] which is configured as a SPAN destination AuditSessionID [chars]

An attempt was made to assign a VLAN to an 802.1x port which is configured as a SPAN destination port

-

"Change the SPAN configuration so that the port is no longer a " "SPAN destination port or change the configuration so that no " "VLAN is assigned."

DOT1X_SWITCH-5-ERR_ADDING_ADDRESS

5-Notice

Unable to add address [enet] on [chars] AuditSessionID [chars]

The authenticated host's address could not be added. This is likely because either the TCAM is full or the address exists as a secure address on another port.

-

"If the TCAM is full clear some dynamic addresses to make " "room for the host's address. If the host's address is " "secured on another port manually remove it from that port."

DOT1X_SWITCH-5-ERR_VLAN_EQ_MDA_INACTIVE

5-Notice

Multi-Domain Authentication cannot activate because Data and Voice VLANs are the same on port AuditSessionID [chars]

Multi-Domain Authentication host mode cannot activate if the configured Data VLAN on a port is the same as Voice VLAN.

-

"Change either the Voice VLAN or the access VLAN on " "the interface so they are not equal anymore. This will cause " "Multi-Domain authentication to activate."

IGMP_SNOOP_ISSU-2-INIT

2-Critical

IGMP Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars]

The IGMP Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

igmp-snooping

LOG_STD_ACTION

IGMP_SNOOP_ISSU-3-TRANSFORM_FAIL

3-Error

IGMP Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The IGMP Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the IGMP Snooping state between the active device and the standby device is not identical.

igmp-snooping

"show issu session <client_id> and " "show issu negotiated version <session_id>"

IGMP_SNOOP_ISSU-3-MSG_NOT_OK

3-Error

IGMP Snooping ISSU client 'Message Type [dec]' is not compatible

The IGMP Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed.

igmp-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

IGMP_SNOOP_ISSU-3-MSG_SIZE

3-Error

IGMP Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to calculate the MTU for the specified message. The IGMP Snooping ISSU client is not able to send the message to the standby device.

igmp-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

IGMP_SNOOP_ISSU-3-INVALID_SESSION

3-Error

IGMP Snooping ISSU client does not have a valid registered session.

The IGMP Snooping ISSU client does not have a valid registered session.

igmp-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-2-SESSION_REGISTRY

2-Critical

IGMP Snooping ISSU client failed to register session information. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

igmp-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-3-SESSION_UNREGISTRY

3-Error

IGMP Snooping ISSU client failed to unregister session information. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to unregister session information.

igmp-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-2-SESSION_NEGO

2-Critical

IGMP Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The IGMP Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

igmp-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

IGMP_SNOOP_ISSU-2-SEND_NEGO_FAILED

2-Critical

IGMP Snooping ISSU client failed to send negotiation message. Error: [dec] [chars]

The IGMP Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

igmp-snooping

"show logging and show checkpoint client"

IGMP_SNOOP_ISSU-2-GET_BUFFER

2-Critical

IGMP Snooping ISSU client failed to get buffer for message. Error: [dec] [chars]

The allocation of explicit-tracking entries is bounded to avoid\n\ the IGMP/MLD snooping hogs the system resources

igmp/mld snooping

"Disable and re-enable L2 multicast snooping on the VLAN."

L2MCAST_WIRELESS_ISSU-2-INIT

2-Critical

L2mcast Wireless ISSU client initialization failed to [chars]. Error: [dec] [chars]

The L2mcast Wireless ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

ewlc-multicast

LOG_STD_ACTION

L2MCAST_WIRELESS_ISSU-3-TRANSFORM_FAIL

3-Error

L2mcast Wireless ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The L2mcast Wireless ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the L2mcast Wireless state between the active device and the standby device is not identical.

ewlc-multicast

"show issu session <client_id> and " "show issu negotiated version <session_id>"

L2MCAST_WIRELESS_ISSU-3-MSG_NOT_OK

3-Error

L2mcast Wireless ISSU client 'Message Type [dec]' is not compatible

The L2mcast Wireless ISSU client received an incompatible message from the peer device. The message cannot be processed.

ewlc-multicast

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

L2MCAST_WIRELESS_ISSU-3-MSG_SIZE

3-Error

L2mcast Wireless ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The L2mcast Wireless ISSU client failed to calculate the MTU for the specified message. The L2mcast Wireless ISSU client is not able to send the message to the standby device.

ewlc-multicast

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

L2MCAST_WIRELESS_ISSU-3-INVALID_SESSION

3-Error

L2mcast Wireless ISSU client does not have a valid registered session.

The L2mcast Wireless ISSU client does not have a valid registered session.

ewlc-multicast

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

L2MCAST_WIRELESS_ISSU-2-SESSION_REGISTRY

2-Critical

L2mcast Wireless ISSU client failed to register session information. Error: [dec] [chars]

The L2mcast Wireless ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

ewlc-multicast

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

L2MCAST_WIRELESS_ISSU-3-SESSION_UNREGISTRY

3-Error

L2mcast Wireless ISSU client failed to unregister session information. Error: [dec] [chars]

The L2mcast Wireless ISSU client failed to unregister session information.

ewlc-multicast

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

L2MCAST_WIRELESS_ISSU-2-SESSION_NEGO

2-Critical

L2mcast Wireless ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The L2mcast Wireless ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ewlc-multicast

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

L2MCAST_WIRELESS_ISSU-2-SEND_NEGO_FAILED

2-Critical

L2mcast Wireless ISSU client failed to send negotiation message. Error: [dec] [chars]

The L2mcast Wireless ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ewlc-multicast

"show logging and show checkpoint client"

L2MCAST_WIRELESS_ISSU-2-GET_BUFFER

2-Critical

L2mcast Wireless ISSU client failed to get buffer for message. Error: [dec] [chars]

The L2mcast Wireless ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

ewlc-multicast

"show logging and show checkpoint client"

MLD_SNOOP_ISSU-2-INIT

2-Critical

MLD Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MLD Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

mld-snooping

LOG_STD_ACTION

MLD_SNOOP_ISSU-3-TRANSFORM_FAIL

3-Error

MLD Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MLD Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MLD Snooping state between the active device and the standby device is not identical.

mld-snooping

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MLD_SNOOP_ISSU-3-MSG_NOT_OK

3-Error

MLD Snooping ISSU client 'Message Type [dec]' is not compatible

The MLD Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed.

mld-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MLD_SNOOP_ISSU-3-MSG_SIZE

3-Error

MLD Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MLD Snooping ISSU client failed to calculate the MTU for the specified message. The MLD Snooping ISSU client is not able to send the message to the standby device.

mld-snooping

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MLD_SNOOP_ISSU-3-INVALID_SESSION

3-Error

MLD Snooping ISSU client does not have a valid registered session.

The MLD Snooping ISSU client does not have a valid registered session.

mld-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-2-SESSION_REGISTRY

2-Critical

MLD Snooping ISSU client failed to register session information. Error: [dec] [chars]

The MLD Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

mld-snooping

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-3-SESSION_UNREGISTRY

3-Error

MLD Snooping ISSU client failed to unregister session information. Error: [dec] [chars]

The MLD Snooping ISSU client failed to unregister session information.

mld-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-2-SESSION_NEGO

2-Critical

MLD Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MLD Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mld-snooping

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MLD_SNOOP_ISSU-2-SEND_NEGO_FAILED

2-Critical

MLD Snooping ISSU client failed to send negotiation message. Error: [dec] [chars]

The MLD Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mld-snooping

"show logging and show checkpoint client"

MLD_SNOOP_ISSU-2-GET_BUFFER

2-Critical

MLD Snooping ISSU client failed to get buffer for message. Error: [dec] [chars]

The MLD Snooping ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mld-snooping

"show logging and show checkpoint client"

MVR_ISSU-2-INIT

2-Critical

MVR ISSU client initialization failed to [chars]. Error: [dec] [chars]

The MVR ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

mvr

LOG_STD_ACTION

MVR_ISSU-3-TRANSFORM_FAIL

3-Error

MVR ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The MVR ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the MVR state between the active device and the standby device is not identical.

mvr

"show issu session <client_id> and " "show issu negotiated version <session_id>"

MVR_ISSU-3-MSG_NOT_OK

3-Error

MVR ISSU client 'Message Type [dec]' is not compatible

The MVR ISSU client received an incompatible message from the peer device. The message cannot be processed.

mvr

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MVR_ISSU-3-MSG_SIZE

3-Error

MVR ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The MVR ISSU client failed to calculate the MTU for the specified message. The MVR ISSU client is not able to send the message to the standby device.

mvr

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

MVR_ISSU-3-INVALID_SESSION

3-Error

MVR ISSU client does not have a valid registered session.

The MVR ISSU client does not have a valid registered session.

mvr

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-2-SESSION_REGISTRY

2-Critical

MVR ISSU client failed to register session information. Error: [dec] [chars]

The MVR ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

mvr

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-3-SESSION_UNREGISTRY

3-Error

MVR ISSU client failed to unregister session information. Error: [dec] [chars]

The MVR ISSU client failed to unregister session information.

mvr

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-2-SESSION_NEGO

2-Critical

MVR ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The MVR ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvr

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

MVR_ISSU-2-SEND_NEGO_FAILED

2-Critical

MVR ISSU client failed to send negotiation message. Error: [dec] [chars]

The MVR ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvr

"show logging and show checkpoint client"

MVR_ISSU-2-GET_BUFFER

2-Critical

MVR ISSU client failed to get buffer for message. Error: [dec] [chars]

The MVR ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

mvr

"show logging and show checkpoint client"

IGMP_QUERIER-4-SAME_SRC_IP_ADDR

4-Warning

An IGMP General Query packet with the same source IP address [inet]

The IGMP querier has received an IGMP General Query message with a source IP address identical to that configured for the IGMP querier itself. This is considered a network configuration error.

igmp

"Check IGMP querier source IP address configuration on the router " "or switch connected via the port identified." "Ensure unique source IP addresses are configured on each system. "

IGMP_QUERIER-4-ZERO_SRC_IP_ADDR

4-Warning

An IGMP General Query packet with source IP address that contained all zeroes is received in VLAN [dec] on port [chars].

The IGMP querier has received an IGMP General Query message with a source IP address that contained all zeroes. Some IGMP clients cannot process General Query with source IP address that contained all zeroes.

igmp

"Check the source IP address of the IGMP querier that is on the router " "or switch connected to the port specified in the message. "

IGMP_QUERIER-4-SNOOPING_DISABLED

4-Warning

The IGMP querier is operationally disabled in VLAN [dec] because IGMP snooping has been disabled in this VLAN.

IGMP snooping has been detected as being disabled on this VLAN. The IGMP querier function should not be operationally enabled when IGMP snooping is disabled.

igmp

"Ensure that IGMP snooping is enabled globally and on the VLAN " "reported. "

IGMP_QUERIER-6-SNOOPING_ENABLED

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because IGMP snooping is no longer disabled.

IGMP snooping has now been enabled and as a result the IGMP querier function has now been enabled.

igmp

"No action is required."

IGMP_QUERIER-4-PIM_ENABLED

4-Warning

The IGMP querier is operationally disabled in VLAN [dec] because PIM has been enabled on the SVI.

PIM has been detected on the SVI. The IGMP querier function should not be operationally enabled when PIM is enabled on the SVI.

igmp

"Ensure that PIM is disabled on the SVI. "

IGMP_QUERIER-6-PIM_DISABLED

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because PIM is no longer enabled on the SVI.

PIM has been disabled on the SVI and as a result the IGMP querier function has now been enabled.

igmp

"No action is required."

IGMP_QUERIER-4-NO_IP_ADDR_CFG

4-Warning

The IGMP querier cannot send out General Query messages in VLAN [dec] because there is no IP address configured on the system.

An IP address should be specified for the IGMP querier either at the global or per VLAN level.

igmp

"Configure a source IP address for the IGMP querier. "

IGMP_QUERIER-6-SWITCHOVER_NOTIFICATION

6-Information

The IGMP querier is now operationally enabled in VLAN [dec] because switchover has occured.

Switchover has occured and the IGMP querier function has now been enabled.

igmp

"No action is required."

SW_MACAUTH-4-UNAUTH_MAC

4-Warning

Unauthenticated MAC [enet] on port [chars]

The switch has received an unauthenticated MAC address on the specified\n\ port.

mac-authentication

LOG_STD_NO_ACTION

SW_MACAUTH-5-MAC_AUTHENTICATED

5-Notice

MAC [enet] was authenticated

The switch has received a cli to authenticate a MAC.

mac-authentication

LOG_STD_NO_ACTION

SW_MACAUTH-5-MACAUTH_ENADSA

5-Notice

MAC Authentication [chars]

MAC Authentication was just enabled/disabled

mac-authentication

LOG_STD_NO_ACTION

SW_MACAUTH-5-CLEAR_TABLE

5-Notice

MAC Authentication Table Cleared

MAC Authentication Table was cleared.

mac-authentication

LOG_STD_NO_ACTION

PM_PVLAN_ISSU-3-INIT

3-Error

pm_pvlan Client Name ISSU client initialization failed at [chars] error [chars]

pm_pvlan Client Name ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

c7600-l2

LOG_STD_SH_TECH_ACTION

PM_PVLAN_ISSU-3-TRANSFORM

3-Error

Private Vlan ISSU client [chars] transform failed error [chars]

Private Vlan ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the pm_pvlan Client Name state will not\n\ be indentical with the active unit.

c7600-l2

"show issu session <client_id> and \n\ show issu negotiated version <session_id>"

PM_PVLAN_ISSU-3-MSG_NOT_OK

3-Error

Private Vlan ISSU client message [dec] is not compatible

Private Vlan ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

c7600-l2

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

PM_PVLAN_ISSU-3-MSG_SIZE

3-Error

Private Vlan ISSU client failed to get the message size for message [dec]

Private Vlan ISSU client failed to calculate message size\n\ for the message specified. The OIR ISSU client will not\n\ be able to send message to the standby unit.

c7600-l2

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

PM_PVLAN_ISSU-3-SESSION

3-Error

Private Vlan ISSU client [chars]

Private Vlan ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

c7600-l2

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

PM_PVLAN_ISSU-3-SEND_FAILED

3-Error

Private Vlan ISSU client failed to send a negotiation message error [dec]

Private Vlan ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the \n\ negotiation the standby unit can not be brought up.

c7600-l2

"show logging and show checkpoint client"

PM_PVLAN_ISSU-3-BUFFER

3-Error

Private Vlan ISSU client failed to get buffer for message error [dec]

Private Vlan ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

c7600-l2

"show logging and show checkpoint client"

PM_PVLAN_ISSU-3-CAPABILITY

3-Error

Private Vlan ISSU client [chars]

Private Vlan ISSU client observed an error during capability\n\ negotiaiton. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

c7600-l2

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

PM_PVLAN_ISSU-3-POLICY

3-Error

Private Vlan ISSU client message type [dec] is [chars]

Private Vlan ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

c7600-l2

"show issu session <client_id>"

PM_ISSU-3-INIT

3-Error

Port Manager ISSU client initialization failed at [chars] error [chars]

Port Manager ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

pm

LOG_STD_SH_TECH_ACTION

PM_ISSU-3-TRANSFORM

3-Error

Port Manager ISSU client [chars] transform failed error [chars]

Port Manager ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Port Manager state will not\n\ be indentical with the active unit.

pm

"show issu session <client_id> and \n\ show issu negotiated version <session_id>"

PM_ISSU-3-MSG_NOT_OK

3-Error

Port Manager ISSU client message [dec] is not compatible

Port Manager ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit

pm

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

PM_ISSU-3-MSG_SIZE

3-Error

Port Manager ISSU client failed to get the message size for message [dec]

Port Manager ISSU client failed to calculate message size\n\ for the message specified. The PM ISSU client will not\n\ be able to send message to the standby unit.

pm

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

PM_ISSU-3-SESSION

3-Error

Port Manager ISSU client [chars]

Port Manager ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

pm

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

PM_ISSU-3-SESSION_UNREGISTRY

3-Error

Port Manager ISSU client failed to unregister session information. Error: [dec] [chars]

The Port Manager ISSU client failed to unregister session information.

pm

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

PM_ISSU-3-SEND_FAILED

3-Error

Port Manager ISSU client failed to send a negotiation message error [dec]

Port Manager ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the \n\ negotiation the standby unit can not be brought up.

pm

"show logging and show checkpoint client"

PM_ISSU-3-BUFFER

3-Error

Port Manager ISSU client failed to get buffer for message error [dec]

Port Manager ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

pm

"show logging and show checkpoint client"

PM_ISSU-3-CAPABILITY

3-Error

Port Manager ISSU client [chars]

Port Manager ISSU client observed an error during capability\n\ negotiaiton. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

pm

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

PM_ISSU-3-POLICY

3-Error

Port Manager ISSU client message type [dec] is [chars]

Port Manager ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

pm

"show issu session <client_id>"

PM_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

Port Manager ISSU client capability exchange result incompatible.

The Port Manager ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

pm

"show issu negotiated capability <Session_ID>"

PM_ISSU-3-CAP_INVALID_SIZE

3-Error

Port Manager ISSU client capability list is empty.

The Port Manager ISSU client capability exchange list size\n\ is invalid.

pm

"show issu capability entries <Client_ID>"

PM-1-INCONSISTENT_PORT_STATE

1-Alert

Inconsistent HW/SW port state for [chars]. Please shut/no shut the interface

The hardware and software port state has become inconsistent.

pm

"Enter the <CmdBold>shutdown<CmdBold> command followed by the\n\ <CmdBold>no shutdown<CmdBold> command on the interface specified in\n\ the message."

PM-2-NOMEM

2-Critical

Not enough memory available for [chars]

The Port Manager subsystem could not obtain the memory it needed.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_COOKIE

4-Warning

[chars] was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_CARD_COOKIE

4-Warning

an invalid card cookie was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_PORT_COOKIE

4-Warning

an invalid port cookie was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_VLAN_COOKIE

4-Warning

an invalid vlan cookie was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_CARD_SLOT

4-Warning

an invalid card slot [dec] was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_PORT_NUMBER

4-Warning

an invalid port number [dec] was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_VLAN_ID

4-Warning

an invalid vlan id [dec] was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_APP_ID

4-Warning

an invalid application id [dec] was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_APP_REQ

4-Warning

an invalid [chars] request by the '[chars]' application was detected

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-TOO_MANY_APP

4-Warning

application '[chars]' exceeded registration limit

An invalid request was detected by the Port Manager.

pm

LOG_STD_SH_TECH_ACTION

PM-4-ERR_DISABLE

4-Warning

[chars] error detected on [chars] putting [chars] in err-disable state

This is a defensive measure that will put the interface in err-disable state when it detects a mis-configuration or mis-behavior . A recovery will be attempted after the configured retry time default 5 minutes.

pm

LOG_STD_SH_TECH_ACTION

PM-4-ERR_RECOVER

4-Warning

Attempting to recover from [chars] err-disable state on [chars]

This is an attempt to bring the interface back after taking it down to\n\ err-disable state

pm

LOG_STD_SH_TECH_ACTION

PM-4-ERR_DISABLE_VP

4-Warning

[chars] error detected on [chars] vlan [dec]. Putting in err-disable state.

This is a defensive measure that will put the virtual port i.e. the port-vlan pair in err-disable state when it detects a mis-configuration or

pm

LOG_STD_SH_TECH_ACTION

PM-4-ERR_RECOVER_VP

4-Warning

Attempting to recover from [chars] err-disable state on [chars] vlan [dec].

This is an attempt to bring the virtual port back after taking it down to err-disable state

pm

LOG_STD_SH_TECH_ACTION

PM-4-UNKNOWN_HOST_ACCESS

4-Warning

Invalid Host access value [dec] is received

Host access table is being accesses with an invalalid host access value

pm

LOG_STD_SH_TECH_ACTION

PM-4-INVALID_HOST_ACCESS_ENTRY

4-Warning

Invalid Host access entry type [dec] is received

Host access entry should be one of configured/dynamic type

pm

LOG_STD_SH_TECH_ACTION

PM-4-BAD_HA_ENTRY_EVENT

4-Warning

Invalid Host access entry event [dec] is received

Host access table is entry event is not any of add/delete/update event

pm

LOG_STD_SH_TECH_ACTION

PM-4-LIMITS

4-Warning

The number of vlan-port instances on [chars] exceeded the recommended limit of [dec]

-

-

"Reduce the number of trunks and VLANs configured in the module " "or switch specified in the error message. Keep the virtual port " "VLAN port count below the recommended limit specified in " "the configuration documentation. Enter the <CmdBold>show " "interface trunk<NoCmdBold> command to see the total number of trunks " "and VLANs."

PM-3-ERR_INCOMP_PORT

3-Error

[dec]/[dec] is set to inactive because [dec]/[dec] is a [chars] port

Private host port can't be configured with trunk private promiscuous and span destination port on the same coil.

-

"Try to configure the incompatible ports on different coils."

PM-4-EXT_VLAN_NOTAVAIL

4-Warning

VLAN [dec] not available in Port Manager

Port Manager failed to allocate the requested VLAN.\n\ The VLAN is either used as an internal VLAN by other features or the\n\ maximum allowed extended VLANs are already configured.

pm

"Try a different VLAN on the device if the limit on maximum allowed\n\ extended VLANs is not yet reached."

PM-4-INT_VLAN_NOTAVAIL

4-Warning

Failed to allocate internal VLAN in Port Manager

Port Manager failed to find any available internal VLAN

pm

"Delete some extened range VLANs created by users or remove some features\n\ that require internal VLAN allocation e.g. routed port"

PM-2-LOW_SP_MEM

2-Critical

Switch process available memory is less than [dec] bytes

Switch Processor available memory dropped to a low level. Possibly\n\ too many Layer 2 VLANs are configured in the system.

pm

"Removed features from the system to reduce memory usage."

PM-4-EXT_VLAN_INUSE

4-Warning

VLAN [dec] currently in use by [chars]

Port Manager failed to allocate the VLAN for external use as the VLAN\n\ is currently occupied by another feature

pm

-

PM-2-VLAN_ADD

2-Critical

Failed to add VLAN [dec] - [chars].

Failed in adding VLAN to VTP. The reason is stated in the string.

pm

LOG_STD_SH_TECH_ACTION

PM-6-EXT_VLAN_ADDITION

6-Information

Extended VLAN is not allowed to be configured in VTP CLIENT mode.

This message will only be seen if you try to configure an extended\n\ VLAN while the switch is in VTP client mode. The configuration will\n\ fail and will not be written to the runnning configuration file but\n\ otherwise switch performance and features will be unaffected.

pm

"This is an informational message only no further action is required.\n\ If you need to configure an extended VLAN you must configure the switch\n\ to leave VTP client mode."

PM-4-NO_SUBBLOCK

4-Warning

No PM subblock found for [chars]

Failed to find PM subblock for this interface.

pm

LOG_STD_SH_TECH_ACTION

PM-4-INT_FAILUP

4-Warning

[chars] failed to come up. No internal VLAN available

Port Manager failed to allocate internal VLAN and thus the interface\n\ cannot come up.

pm

"Remove extended range VLAN to free up resouces."

PM-4-VMPS_CFG

4-Warning

Dynamic access VLAN [dec] same as voice vlan on [chars].

Access VLAN on VMPS server is set to same VLAN as voice VLAN on the\n\ port.

pm

"Access VLAN assignment on VMPS server should be different from voice\n\ VLAN."

PM-4-INACTIVE

4-Warning

putting [chars] in inactive state because [chars]

The Port Manager has been blocked from creating a virtual port for the switch port and VLAN causing the port to be in an inactive state. The reason for this condition is specified in the error message.

pm

LOG_STD_SH_TECH_ACTION

PM-3-INTERNALERROR

3-Error

Port Manager Internal Software Error [chars]: [chars]: [dec]: [chars]

There is an internal software error encountered in the IOS Port Manager.

pm

LOG_STD_ACTION

PM-4-PVLAN_TYPE_CFG_ERR

4-Warning

Failed to set VLAN [dec] to a [chars] VLAN

Platform failed to set private vlan type.

pm

LOG_STD_SH_TECH_ACTION

PM-4-PORT_BOUNCED

4-Warning

Port [chars] was bounced by [chars].

The Port Manager needed to perform a reactivation of a port in the\n\ link down state during a switchover. A port is only reactivated when the\n\ port data structures lack consistency between the active and standby\n\ supervisors. Active ports in the link down state were returned to the\n\ link up state by the reactivation event.

pm

LOG_STD_NO_ACTION

PM-4-MPLS_MTU_PORT_CFG

4-Warning

MPLS MTU size [dec] is not supported by port [chars].

The MPLS MTU size configured on the port is larger than the maximum MTU size that can be supported by this port. As a result large packets can be dropped.

pm

"Reduce the MPLS MTU size."

PM-4-MPLS_MTU_EC_CFG

4-Warning

MPLS MTU size [dec] is not supported by one or more ports in channel [chars].

Port Manager on Standby discovered that the port state has been \n\ inconsistent for more that 1 second. Inconsistent ports are reactivated\n\ on switchover you will see PORT_BOUNCED message.

pm

LOG_STD_NO_ACTION

PM-4-PORT_CONSISTENT

4-Warning

Port [chars] consistency has been restored IDB state: [chars].

Port Manager on Standby discovered that port state became consistent \n\ again.

pm

LOG_STD_NO_ACTION

UDLD-3-UDLD_INTERNAL_ERROR

3-Error

UDLD internal error: [chars]

A softare sanity check failed in the course of UDLD processing.

udld

LOG_STD_SH_TECH_ACTION

UDLD-3-UDLD_INTERNAL_IF_ERROR

3-Error

UDLD internal error interface [chars]: [chars]

A softare sanity check failed in the course of UDLD processing.

udld

LOG_STD_SH_TECH_ACTION

UDLD-3-UDLD_IDB_ERROR

3-Error

UDLD error handling [chars] interface: [chars]

A softare error occurred in UDLD processing associated with a specific\n\ interface.

udld

LOG_STD_SH_TECH_ACTION

UDLD-4-UDLD_PORT_DISABLED

4-Warning

UDLD disabled interface [chars] [chars] detected

An interface was disabled because UDLD protocol detected the cause\n\ indicated on the interface indicated. Cause is likely due to bad\n\ interface hardware or cable misconfiguration. User should investigate.

udld

LOG_STD_SH_TECH_ACTION

UDLD-6-UDLD_PORT_RESET

6-Information

UDLD reset interface [chars]

A port which had been disabled for UDLD has been reset.

udld

LOG_STD_SH_TECH_ACTION

UDLD-4-UDLD_PORT_FAILURE

4-Warning

UDLD failure reported per user request interface [chars] [chars] detected.

An interface failure was reported because UDLD protocol detected the cause\n\ indicated on the interface. Cause is likely due to bad interface hardware\n\ or cable misconfiguration. Interface not err-disabled as user choose to\n\ see error-report. User should investigate and take action.

udld

LOG_STD_SH_TECH_ACTION

SPANTREE_VLAN_SW-2-MAX_INSTANCE

2-Critical

Platform limit of [dec] STP instances exceeded. No instance created for [chars] port [chars].

-

-

-

UFAST_MCAST_SW-4-MEM_NOT_AVAILABLE

4-Warning

No memory is available for transmitting UplinkFast packets on\n\ Vlan [dec].

UplinkFast packets will not be transmitted on Vlan [dec] due to a\n\ lack of memory.

-

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

UFAST_MCAST_SW-3-PROC_START_ERROR

3-Error

No process available for transmitting UplinkFast packets.

UplinkFast packets will not be transmitted as the process could\n\ not be created.

-

"UplinkFast will not work unless you reload. If this problem persists \n\ even after reload please contact your Cisco Technical Support\n\ representative with the configuration and technical support\n\ information."

ACCESS_TUNNEL_ISSU-3-INIT

3-Error

ACCESS_TUNNEL ISSU client initialization failed at [chars] error [chars]

ACCESS_TUNNEL ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed.

accsw-p-securefab

LOG_STD_SH_TECH_ACTION

ACCESS_TUNNEL_ISSU-3-TRANSFORM

3-Error

ACCESS_TUNNEL ISSU client [chars] transform failed error [chars]

ACCESS_TUNNEL ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the ACCESS_TUNNEL state will not\n\ be indentical with the active unit.

accsw-p-securefab

"show issu session <client_id> and \n\ show issu negotiated version <session_id>"

ACCESS_TUNNEL_ISSU-3-MSG_NOT_OK

3-Error

ACCESS_TUNNEL ISSU client message [dec] is not compatible

ACCESS_TUNNEL ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can not be processed by this unit

accsw-p-securefab

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

ACCESS_TUNNEL_ISSU-3-MSG_SIZE

3-Error

ACCESS_TUNNEL ISSU client failed to get the message size for message [dec]

ACCESS_TUNNEL ISSU client failed to calculate message size\n\ for the message specified. The ACCESS_TUNNEL ISSU client will not\n\ be able to send message to the standby unit.

accsw-p-securefab

"show issu message group <client_id> and\n\ show issu session <client_id> and \n\ show issu negotiated version <session_id>"

ACCESS_TUNNEL_ISSU-3-SESSION

3-Error

ACCESS_TUNNEL ISSU client [chars]

ACCESS_TUNNEL ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up.

accsw-p-securefab

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

ACCESS_TUNNEL_ISSU-3-SESSION_UNREGISTRY

3-Error

ACCESS_TUNNEL ISSU client failed to unregister session information. Error: [dec] [chars]

The ACCESS_TUNNEL ISSU client failed to unregister session information.

accsw-p-securefab

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

ACCESS_TUNNEL_ISSU-3-SEND_FAILED

3-Error

ACCESS_TUNNEL ISSU client failed to send a negotiation message error [dec]

ACCESS_TUNNEL ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the \n\ negotiation the standby unit can not be brought up.

accsw-p-securefab

"show logging and show checkpoint client"

ACCESS_TUNNEL_ISSU-3-BUFFER

3-Error

ACCESS_TUNNEL ISSU client failed to get buffer for message error [dec]

ACCESS_TUNNEL ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can not send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up.

accsw-p-securefab

"show logging and show checkpoint client"

ACCESS_TUNNEL_ISSU-3-CAPABILITY

3-Error

ACCESS_TUNNEL ISSU client [chars]

ACCESS_TUNNEL ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit.

accsw-p-securefab

"show issu capability entries <client_id> and \n\ show issu session <client_id> and \n\ show issu negotiated capability <session_id>"

ACCESS_TUNNEL_ISSU-3-POLICY

3-Error

ACCESS_TUNNEL ISSU client message type [dec] is [chars]

ACCESS_TUNNEL ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible.

accsw-p-securefab

"show issu session <client_id>"

ACCESS_TUNNEL_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

ACCESS_TUNNEL ISSU client capability exchange result incompatible.

The ACCESS_TUNNEL ISSU client capability exchange has negotiated\n\ as incompatible with the peer.

accsw-p-securefab

"show issu negotiated capability <Session_ID>"

ACCESS_TUNNEL_ISSU-3-CAP_INVALID_SIZE

3-Error

ACCESS_TUNNEL ISSU client capability list is empty.

The ACCESS_TUNNEL ISSU client capability exchange list size\n\ is invalid.

accsw-p-securefab

"show issu capability entries <Client_ID>"

MAC_MOVE-4-NOTIF

4-Warning

Host [enet] in vlan [dec] is flapping between port [chars] and port [chars]

The system has found the specified host moving between the specified ports.

cat6000-l2

"Check the network for possible loops."

CLS_ACC-2-MODE_ENTERED

2-Critical

Entering consoleless access mode [chars]

Switch enters one of the consoleless access modes

firmware

LOG_NO_ACTION

CLS_ACC-2-MODE_EXITED

2-Critical

Complete consoleless access from mode [chars]

Switch exits from one of the consoleless access modes

firmware

LOG_NO_ACTION

CLS_ACC-4-UNEXPECTEDEVENT

4-Warning

Switch does not support or not ready for consoleless access mode

Switch either does not support or is not ready to enter the requested consoleless access mode

firmware

LOG_NO_ACTION

CLS_ACC-7-ACC_INTF

7-Debug

Selected management interface: [chars] interface number: [dec]

Selected an interface as consoleless access interface

firmware

LOG_NO_ACTION

CLS_ACC-3-NO_ACC_INTF

3-Error

Failed to find a free interface as consoleless access interface or failed to retrieve the access interface information

Not able to find a free interface which is fit to serve as management interface for consoleless access

firmware

LOG_NO_ACTION

CLS_ACC-7-ACC_VLAN

7-Debug

Selected vlan [dec] for consoleless access

A new vlan is created to only include the management interface Vlan creation successful

firmware

LOG_NO_ACTION

CLS_ACC-3-VLAN_CREATE_FAIL

3-Error

Failed to allocate a free vlan as consoleless access vlan use default mamagement vlan

Not able to find a free vlan in the range of 2-1000 to server as management vlan for consoleless access

firmware

LOG_NO_ACTION

CLS_ACC-3-CONFIG_ERROR

3-Error

[chars]

Not able to correctly configure the switch for consoleless access Can't go to access mode

firmware

LOG_NO_ACTION

CLS_ACC-2-SETUP_BTN_PRS

2-Critical

[chars]

Pressing the switch setup button will lead an unconfigured switch to go to express setup mode. It will not have any effect on an already configured switch. Pressing the setup button for more than 5 seconds will lead a configured switch to go to direct management mode or lead an unconfigured switch to go to express setup mode

firmware

LOG_NO_ACTION

CLS_ACC-2-CONFIG_NV_DATA

2-Critical

Express setup parameter committed. Default port role will be applied

After express setup parameters are committed switch becomes a configured switch. The default port roles are automatically applied to all ports at this moment. The port role configurations may be manually modified after this point.

firmware

LOG_NO_ACTION

CLS_ACC-2-NO_PROCESS

2-Critical

Process creation failure

Failed to create process to execute consoleless access

firmware

LOG_NO_ACTION

CLS_ACC-3-NOSOCKET

3-Error

Fail to create DNS socket for consoleless access

Socket creation failure switch is not able to go into consoleless access mode. Abort.

firmware

LOG_NO_ACTION

CLS_ACC-4-NO_HTTP_PAGE

4-Warning

Failed to locate HTTP page for the consoleless access mode

Not able to locate the HTTP page corresponding to the access mode. Page is not on flash

firmware

LOG_NO_ACTION

CLS_ACC-3-UNABLE_TO_RESET_CONFIG

3-Error

[chars]

The system is unable to reset the configuration

firmware

LOG_STD_ACTION

CLS_ACC-7-CONFIG

7-Debug

Save access intf config: if: [chars] port num: [dec] vlan [dec] admin-down?:[dec]

Save interface configurations these configurations will be restored when consoleless access exits and returns the interface

firmware

LOG_NO_ACTION

CLS_ACC-7-CONFIG_SUCCESS

7-Debug

[chars]

Consoleless access mgmt interface successfully configured or its original configuration successfully restored

firmware

LOG_NO_ACTION

CLS_ACC-3-NOMEMORY

3-Error

[chars]

Memory allocation failure for executing consoleless access switch configuration commands

firmware

LOG_STD_ACTION

CLS_ACC-5-CLRCFG

5-Notice

User cleared switch configurations under recovery mode

Under consoleless access mode user takes an action to reset switch configuration to factory default.

firmware

LOG_NO_ACTION

CLS_ACC-5-RSTIMG

5-Notice

User reset switch image to factory default image under recovery mode

Under consoleless access mode user takes an action to reset switch image to factory default.

firmware

LOG_NO_ACTION

EXPRESS_SETUP-6-MODE_ENTERED

6-Information

-

Express setup mode is now active

firmware

LOG_NO_ACTION

EXPRESS_SETUP-6-MODE_EXITED

6-Information

-

Express setup mode is no longer active

firmware

LOG_NO_ACTION

EXPRESS_SETUP-3-UNABLE_TO_RESET_CONFIG

3-Error

[chars]

The system is unable to reset the configuration

firmware

LOG_STD_ACTION

EXPRESS_SETUP-5-CONFIG_IS_RESET

5-Notice

[chars]

The configuration is reset and the system will now reboot

firmware

LOG_STD_ACTION

EXPRESS_SETUP-6-MODE_BUTTON_RESET_IGNORED

6-Information

[chars]

mode button pressed for more than 10Sec and startup config is present hence not reloading

firmware

LOG_NO_ACTION

FRNTEND_CTRLR-1-MGR_TXQ_FULL

1-Alert

The front end controller Tx queue reached watermark level

The queue between microcontroller controlling the front end and IOS has reached the watermark level. Too many messages are pending in the queue

firmware

"Please try reloading the switch. If it does not fix the " "problem this could be a bad hardware. Contact the Cisco " "technical support representative"

FRNTEND_CTRLR-2-SUB_INACTIVE

2-Critical

The front end controller [dec] is inactive

The microcontroller controlling the front end has become inactive. This controls the Port LEDs Uplink LEDs Power over ethernet and thermal/fan control functionality. These functionalities will not work on the ports controlled by this microcontroller. This does not have any impact on data traffic

hardware

"Please try a reset of the hardware. If it does not fix the " "problem this could be a bad hardware. Contact the Cisco " "technical support representative"

FRNTEND_CTRLR-1-RELOAD_REQD

1-Alert

A UCODE upgrade has taken place without a reload. There must be a reload in order to complete the upgrade. Some features will not work properly until the reload is performed.

The UCODE images were upgraded during an archive download software upgrade but the switch was not reloaded as part of the upgrade. The switch must be reloaded to complete the upgrade. Until the switch is reloaded PoE thermal power supply and stack-power features will not be completely supported.

firmware

"Please reload the switch at the earliest convenience."

SW_VLAN-6-VTP_MODE_CHANGE

6-Information

VLAN manager changing device mode from [chars] to [chars].

Some switch devices must automatically change VTP device modes upon\n\ receipt of a VLAN configuration database containing more than a set\n\ number of VLANs depending on the device. This message indicates that\n\ such a spontaneous conversion has occurred what the previous mode was\n\ and what the current mode is.

sw-vlan vtp

LOG_STD_NO_ACTION

SW_VLAN-6-VTP_DOMAIN_NAME_CHG

6-Information

VTP domain name changed to [chars].

The VTP domain name was changed through configuration to the name\n\ specified in the message. A management domain is the naming scope\n\ of a VLAN name. Each VLAN has a name that is unique within the\n\ management domain.

sw-vlan vtp

LOG_STD_NO_ACTION

SW_VLAN-4-VTP_FLOOD_ERROR

4-Warning

Primary server request failed\nPrimary server can only change once \n\ every [dec] seconds

VTP takeover packet received within takeover rate limit

sw-vlan vtp

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VTP_INTERNAL_ERROR

4-Warning

VLAN manager received an internal error [dec] from vtp function [chars]: [chars]

An unexpected error code was received by the VLAN Manager from the VTP\n\ configuration software.

sw-vlan vtp

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VTP_INVALID_DATABASE_DATA

4-Warning

VLAN manager received bad data of type [chars]: value [dec] from vtp database\n\ function [chars]

Invalid data was received by the VLAN Manager from a VTP configuration\n\ database routine.

sw-vlan vtp

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-NO_PM_COOKIE_RETURNED

4-Warning

VLAN manager unexpectedly received a null [chars] type cookie from the Port\n\ Manager data reference: [chars]

The VLAN manager queried the Port Manager for a reference cookie but\n\ received a NULL pointer instead.

sw-vlan pm

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-BAD_PM_VLAN_COOKIE_RETURNED

4-Warning

VLAN manager unexpectedly received a bad PM VLAN cookie from the Port\n\ Manager VLAN indicated: [dec]

The VLAN manager received an upcall from the Port Manager containing a\n\ VLAN cookie which translated to a bad VLAN number.

sw-vlan pm

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VTP_INVALID_EVENT_DATA

4-Warning

VLAN manager received bad data of type [chars]: value [dec] while being called\n\ to handle a [chars] event

Invalid data was received by the VLAN Manager from the VTP configuration\n\ software.

sw-vlan vtp

LOG_STD_SH_TECH_ACTION

SW_VLAN-3-VTP_PROTOCOL_ERROR

3-Error

VTP protocol code internal error: [chars]

VTP protocol code encountered an unexpected error will processing\n\ configuration request packet or timer expiration.

sw-vlan vtp

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VTP_USER_NOTIFICATION

4-Warning

VTP protocol user notification: [chars]

VTP protocol code encountered an unusual diagnostic situation which the\n\ user should be made aware of.

sw-vlan vtp

LOG_STD_ACTION

SW_VLAN-4-IFS_FAILURE

4-Warning

VLAN manager encountered file operation error: call = [chars] / file = [chars] / code = [dec] [chars] / bytes transfered = [dec]

The VLAN manager received an unexpected error return from a IOS file\n\ system call.

sw-vlan ifs

LOG_STD_ACTION

SW_VLAN-4-BAD_VLAN_CONFIGURATION_FILE

4-Warning

VLAN configuration file contained incorrect verification word: 0x[hec]

The VLAN configuration file read by the VLAN manager did not begin with\n\ correct value which would indicate a valid VLAN configuration file. Thus\n\ it has been rejected.

sw-vlan ifs

LOG_STD_ACTION

SW_VLAN-4-BAD_VLAN_CONFIGURATION_FILE_VERSION

4-Warning

VLAN configuration file contained unknown file version: [dec]

The VLAN configuration file read by the VLAN manager contained an\n\ unrecognized file version number. This may indicate an attempt to\n\ regress to an older version of the VLAN manager software.

sw-vlan ifs

LOG_STD_ACTION

SW_VLAN-4-BAD_VLAN_DOMAIN_NAME_LENGTH

4-Warning

VLAN configuration file contained incorrect domain name length: [dec]

The VLAN configuration file read by the VLAN manager did not contain a valid domain name length. Thus it has been rejected.

sw-vlan ifs

"Please provision VTP domain name again"

SW_VLAN-4-BAD_VLAN_PASSWORD_LENGTH

4-Warning

VLAN configuration file contained incorrect VTP password length: [dec]

The VLAN configuration file read by the VLAN manager did not contain a valid VTP password length. Thus it has been rejected.

sw-vlan ifs

"Please provision VTP password again"

SW_VLAN-4-BAD_VLAN_TIMER_ACTIVE_VALUE

4-Warning

Encountered incorrect VLAN timer active value: [chars]

Due to a software error a VLAN timer was dectected active when it\n\ should have been inactive or inactive when it should have been active.

sw-vlan vtp

LOG_STD_ACTION

SW_VLAN-3-VLAN_PM_NOTIFICATION_FAILURE

3-Error

VLAN Manager synchronization failure with Port Manager over [chars]

Due to lack of ready pool space the VLAN manager dropped a notification\n\ from the Port Manager as indicated by the message.

sw-vlan vtp pm

LOG_STD_ACTION

SW_VLAN-6-OLD_CONFIG_FILE_READ

6-Information

Old version [dec] VLAN configuration file detected and read OK. Version [dec]\n\ files will be written in the future.

VLAN software detected an old version of the VLAN configuration file\n\ format. It was able to interpret the file with no problems but will\n\ create files using the new format in the future.

sw-vlan vtp

LOG_STD_NO_ACTION

SW_VLAN-4-BAD_STARTUP_VLAN_CONFIG_FILE

4-Warning

Failed to configure VLAN from startup-config. Fallback to use VLAN configuration file from non-volatile memory

VLAN software failed to use VLAN configuration from startup-config\n\ file. It will fallback to use the binary VLAN configuration file\n\ in non-volatile memory.

sw-vlan

LOG_STD_NO_ACTION

SW_VLAN-4-EXT_VLAN_INTERNAL_ERROR

4-Warning

Extended VLAN manager received an internal error [dec] from [chars]: [chars]

An unexpected error code was received by the VLAN Manager from the \n\ extended VLAN configuration software.

sw-vlan

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-EXT_VLAN_INVALID_DATABASE_DATA

4-Warning

Extended VLAN manager received bad data of type [chars]: value [dec] from \n\ function [chars]

Invalid data was received by the extended VLAN Manager from an extended\n\ VLAN configuration database routine.

sw-vlan

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VLANMGR_INVALID_DATABASE_DATA

4-Warning

VLAN MANAGER received bad data of type [chars]: value [dec] from function [chars]

Invalid data was received by the VLAN MANAGER from a VLAN configuration database routine.

sw-vlan

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VLAN_CREATE_FAIL

4-Warning

Failed to create VLANs [chars]: [chars]

The VLANs specified in the error message could not be created. The VLAN manager called an VLAN database routine to create one or more VLANs but the Port Manager failed the VLAN creation requests. A possible cause of this error is that the VLANs already exist in the Port Manager as internal VLANs.

sw-vlan

"Check the internal VLAN usage using 'show vlan internal usage' command. " "Unconfigure the feature which occupies the internal VLAN and retry " "the VLAN creation operation." LOG_STD_SH_TECH_ACTION

SW_VLAN-4-STARTUP_EXT_VLAN_CONFIG_FILE_FAILED

4-Warning

Failed to configure extended range VLAN from startup-config. Error [chars]

VLAN software failed to use extended VLAN configuration from\n\ startup-config file. All extended range VLANs configuration will be lost\n\ after system boot up.

sw-vlan

LOG_STD_NO_ACTION

SW_VLAN-4-VTP_SEM_BUSY

4-Warning

VTP semaphore is unavailable for function [chars]. Semaphore locked by [chars]

The VTP database is currently locked by another task and is not available.\n\ Users should retry the operation sometime later.

sw-vlan vtp

LOG_STD_SH_TECH_ACTION

SW_VLAN-3-MALLOC_FAIL

3-Error

Failed to allocate [dec] bytes

Memory allocation failed.

sw-vlan

LOG_STD_SH_TECH_ACTION

SW_VLAN-6-VLAN_DAT_CACHE_EXISTS

6-Information

Unexpected vlan.dat cache exists. Removing the cache and continuing the sync with new set.

vlan.dat file is synced to the STANDBY via one or more checkpoint message from ACTIVE. The sequence number for each such set of checkpoint messages starts with 1. These messages are cached at the STANDBY till the end-of-set indication is received. Here the STANDBY received a checkpoint message with a size that does not fit the size of cache specified in the checkpoint message with sequence number 1. Please report it to Customer Support.

sw-vlan

LOG_STD_SH_TECH_ACTION

SW_VLAN-4-VTP_PRIMARY_SERVER_CHG

4-Warning

[enet] has become the primary server for the [chars] VTP feature

The primary server status has changed and the indicated device has become the primary server for the indicated VTP feature.

sw-vlan

LOG_STD_NO_ACTION

SW_VLAN-4-VTP_DB_SIZE_CHECK_FAILED

4-Warning

The [chars] VTP database of length [dec] cannot be supported by the system

The VTP database size is more than what the system can support.

sw-vlan

"Reduce the database size by decreasing the configuration parameters " "example reduce the size of vlan-names"

SW_VLAN-3-IIF_ID_ALLOC_FAILED

3-Error

IIF_ID alloc failed for vlan [dec] due to memory allocation failure. Some features will not work.

The system is low on memory due to which IIF-ID allocation failed. This results in failure to apply polices such as QoS and Security acls on this vlan.

sw-vlan

LOG_STD_REDUCE_ACTION "Once memory is available shutdown the vlan and then unshut the vlan"

SW_VLAN-3-IIF_ID_REGISTRATION_FAILED

3-Error

IIF_ID registration failed for vlan [dec] due to memory allocation failure. Some features will not work. Vlan has been shutdown

The system is low on memory due to which IIF-ID registration failed. This results in failure to apply polices such as QoS and Security acls on this vlan. If vlan exists it is shutdown. If vlan doesn't exist then it will be shutdown when it is created.

sw-vlan

LOG_STD_REDUCE_ACTION "Once memory is available run 'no shutdown' on the vlan"

SW_VLAN_ISSU-2-INIT

2-Critical

Switch Vlan ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Switch Vlan ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

sw-vlan

LOG_STD_ACTION

SW_VLAN_ISSU-3-TRANSFORM_FAIL

3-Error

Switch Vlan ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The Switch Vlan ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Switch Vlan state between the active device and the standby device is not identical.

sw-vlan

"show issu session <client_id> and " "show issu negotiated version <session_id>"

SW_VLAN_ISSU-3-MSG_NOT_OK

3-Error

Switch Vlan ISSU client 'Message Type [dec]' is not compatible

The Switch Vlan ISSU client received an incompatible message from the peer device. The message cannot be processed.

sw-vlan

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SW_VLAN_ISSU-3-MSG_SIZE

3-Error

Switch Vlan ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The Switch Vlan ISSU client failed to calculate the MTU for the specified message. The Switch Vlan ISSU client is not able to send the message to the standby device.

sw-vlan

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SW_VLAN_ISSU-3-INVALID_SESSION

3-Error

Switch Vlan ISSU client does not have a valid registered session.

The Switch Vlan ISSU client does not have a valid registered session.

sw-vlan

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SW_VLAN_ISSU-2-SESSION_REGISTRY

2-Critical

Switch Vlan ISSU client failed to register session information. Error: [dec] [chars]

The Switch Vlan ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

sw-vlan

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

SW_VLAN_ISSU-3-SESSION_UNREGISTRY

3-Error

Switch Vlan ISSU client failed to unregister session information. Error: [dec] [chars]

The Switch Vlan ISSU client failed to unregister session information.

sw-vlan

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SW_VLAN_ISSU-2-SESSION_NEGO

2-Critical

Switch Vlan ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Switch Vlan ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

sw-vlan

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

SW_VLAN_ISSU-2-SEND_NEGO_FAILED

2-Critical

Switch Vlan ISSU client failed to send negotiation message. Error: [dec] [chars]

The Switch Vlan ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

sw-vlan

"show logging and show checkpoint client"

SW_VLAN_ISSU-2-GET_BUFFER

2-Critical

Switch Vlan ISSU client failed to get buffer for message. Error: [dec] [chars]

The Switch Vlan ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

sw-vlan

"show logging and show checkpoint client"

SW_VLAN_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER

3-Error

'Message Type [dec]' is not supported by Switch Vlan ISSU client at peer

The Switch Vlan ISSU client at the peer supervisor is not compatible for this message type. The Switch Vlan client will be marked as incompatible with the peer.

sw-vlan

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

SW_VLAN_ISSU-3-CAP_NOT_COMPATIBLE

3-Error

Switch Vlan ISSU client capability exchange result incompatible.

The Switch Vlam ISSU client capability exchange have negotiated as incompatible with the peer.

sw-vlan

"show issu negotiated capability <Session_ID>"

SW_VLAN_ISSU-3-CAP_INVALID_SIZE

3-Error

Switch Vlan ISSU client capability list is empty.

The Switch Vlan ISSU client capability exchange list size is invalid.

sw-vlan

"show issu capability entires <Client_ID>"

SW_VLAN_ISSU-3-DOWNGRADE_NOT_ALLOWED_WITH_VTPV3

3-Error

VTP version [dec] is configured in vlan.dat file. Device cannot be downgraded to an image that does not support this VTP version.

The VTP version is not saved in startup or running config. It is stored in vlan.dat file. If vlan.dat file content is copied from some other source or if the pre-requisites for 'VTP version 3' is removed from the system via CLI and then the system is re-started the efective VTP version differs from the one stored in the file.

sw-vlan

"Please use 'vtp version' CLI to re-configure VTP version."

AUTOQOS_ISSU-2-INIT

2-Critical

AutoQoS ISSU client initialization failed to [chars]. Error: [dec] [chars]

The AutoQoS ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

autoqos

LOG_STD_ACTION

AUTOQOS_ISSU-3-TRANSFORM_FAIL

3-Error

AutoQoS ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars]

The AutoQoS ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the AutoQoS state between the active device and the standby device is not identical.

autoqos

"show issu session <client_id> and " "show issu negotiated version <session_id>"

AUTOQOS_ISSU-3-MSG_NOT_OK

3-Error

AutoQoS ISSU client 'Message Type [dec]' is not compatible

The AutoQoS ISSU client received an incompatible message from the peer device. The message cannot be processed.

autoqos

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

AUTOQOS_ISSU-3-MSG_SIZE

3-Error

AutoQoS ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars]

The AutoQoS ISSU client failed to calculate the MTU for the specified message. The AutoQoS ISSU client is not able to send the message to the standby device.

autoqos

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

AUTOQOS_ISSU-3-INVALID_SESSION

3-Error

AutoQoS ISSU client does not have a valid registered session.

The AutoQoS ISSU client does not have a valid registered session.

autoqos

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

AUTOQOS_ISSU-2-SESSION_REGISTRY

2-Critical

AutoQoS ISSU client failed to register session information. Error: [dec] [chars]

The AutoQoS ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

autoqos

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

AUTOQOS_ISSU-3-SESSION_UNREGISTRY

3-Error

AutoQoS ISSU client failed to unregister session information. Error: [dec] [chars]

The AutoQoS ISSU client failed to unregister session information.

autoqos

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

AUTOQOS_ISSU-2-SESSION_NEGO

2-Critical

AutoQoS ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The AutoQoS ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

autoqos

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

AUTOQOS_ISSU-2-SEND_NEGO_FAILED

2-Critical

AutoQoS ISSU client failed to send negotiation message. Error: [dec] [chars]

The AutoQoS ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

autoqos

"show logging and show checkpoint client"

AUTOQOS_ISSU-2-GET_BUFFER

2-Critical

AutoQoS ISSU client failed to get buffer for message. Error: [dec] [chars]

The AutoQoS ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

autoqos

"show logging and show checkpoint client"

SWITCH_QOS_TB-5-TRUST_DEVICE_DETECTED

5-Notice

[chars] detected on port [chars] port's configured trust state is now operational.

Trusted Boundary detected a device matching the trusted device setting for the port and so has modified the port's trust state.

-

LOG_STD_NO_ACTION

SWITCH_QOS_TB-5-TRUST_DEVICE_LOST

5-Notice

[chars] no longer detected on port [chars] operational port trust state is now untrusted.

Trusted Boundary lost contact with a trusted device and so has set the port's trust state to untrusted.

-

LOG_STD_NO_ACTION

PSECURE_ISSU-2-INIT

2-Critical

Port Security ISSU client initialization failed to [chars]. Error: [dec] [chars]

The Port Security ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade.

Port Security

LOG_STD_ACTION

PSECURE_ISSU-3-TRANSFORM_FAIL

3-Error

Port Security ISSU client [chars] transform failed for Message Type [dec] . Error: [dec] [chars]

The Port Security ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Port Security state between the active device and the standby device is not identical.

Port Security

"show issu session <client_id> and " "show issu negotiated version <session_id>"

PSECURE_ISSU-3-MSG_NOT_OK

3-Error

Port Security ISSU client Message Type [dec] is not compatible

The Port Security ISSU client received an incompatible message from the peer device. The message cannot be processed.

Port Security

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

PSECURE_ISSU-3-MSG_SIZE

3-Error

Port Security ISSU client failed to get the MTU for Message Type [dec] . Error: [dec] [chars]

The Port Security ISSU client failed to calculate the MTU for the specified message. The Port Security ISSU client is not able to send the message to the standby device.

Port Security

"show issu message group <client_id> and " "show issu session <client_id> and " "show issu negotiated version <session_id>"

PSECURE_ISSU-3-INVALID_SESSION

3-Error

Port Security ISSU client does not have a valid registered session.

The Port Security ISSU client does not have a valid registered session.

Port Security

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PSECURE_ISSU-2-SESSION_REGISTRY

2-Critical

Port Security ISSU client failed to register session information. Error: [dec] [chars]

The Port Security ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly.

Port Security

"show issu capability entries <client_id> and " "show issu session <client_id> and " "show issu negotiated capability <session_id>"

PSECURE_ISSU-3-SESSION_UNREGISTRY

3-Error

Port Security ISSU client failed to unregister session information. Error: [dec] [chars]

The Port Security ISSU client failed to unregister session information.

Port Security

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

PSECURE_ISSU-2-SESSION_NEGO

2-Critical

Port Security ISSU client encountered unexpected client nego_done. Error: [dec] [chars]

An ISSU-compliant client transitions through a series of internal states. The Port Security ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

Port Security

"show issu session <client_id> and " "show issu negotiated capability <session_id>"

PSECURE_ISSU-2-SEND_NEGO_FAILED

2-Critical

Port Security ISSU client failed to send negotiation message. Error: [dec] [chars]

The Port Security ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

Port Security

"show logging and show checkpoint client"

PSECURE_ISSU-2-GET_BUFFER

2-Critical

Port Security ISSU client failed to get buffer for message. Error: [dec] [chars]

The Port Security ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly.

Port Security

"show logging and show checkpoint client"

PORT_SECURITY-2-PSECURE_VIOLATION

2-Critical

Security violation occurred caused by MAC address [enet] on port [chars].

An unauthorized device attempted to connect on a secure port. The MAC address of the unauthorized device and the secure port are specified in the error message.

Port Security

"Determine the device that attempted to connect on the secure port." "Notify your network system administrator of this condition."

PORT_SECURITY-2-PSECURE_VIOLATION_VLAN

2-Critical

Security violation on port [chars] due to MAC address [enet] on VLAN [dec]

An unauthorized device attempted to connect on a secure trunk port. The MAC address of the unauthorized device and the secure trunk and VLAN are specified in the error message.

Port Security

"Determine the device that attempted to connect via the secure trunk " "port. Notify your network system administrator of this condition."

PORT_SECURITY-6-VLAN_REMOVED

6-Information

VLAN [dec] is no longer allowed on port [chars]. Its port security configuration has been removed.

A configured VLAN has been excluded either due to port mode change or allowed VLAN list change and is removed from the configuration.

Port Security

LOG_STD_NO_ACTION

PORT_SECURITY-6-ADDR_REMOVED

6-Information

Address <[dec]:[enet]> exists on port [chars]. It has been removed from port [chars].

A routed port has changed to a switched port. An address stored in the previous switched port configuration is now in conflict and has been deleted.

Port Security

LOG_STD_NO_ACTION

PORT_SECURITY-6-VLAN_FULL

6-Information

Vlan [dec] on port [chars] has reached its limit. Address [enet] has been removed.

The voice VLAN has become the same as the access VLAN but the number of addresses allowed on the access VLAN has been reached so the address has been deleted.

Port Security

LOG_STD_NO_ACTION

PORT_SECURITY-6-ADDRESSES_REMOVED

6-Information

Maximum system secure address count reached. Some secure addresses configured on port [chars] removed.

Some configured and sticky MAC addresses on the specified port were removed from the configuration. The number of secure addresses that the system supports was exceeded. This condition occurs only during hot swapping or port-mode changes for example when the port is converted from a L3 to a L2 port.

-

-

PORT_SECURITY-6-ADDR_ADDFAIL

6-Information

Address <[dec]:[enet]> could not be added to [chars] due to [chars].

In some rare cases MAC addresses are learnt before all software modules finished initialization and fully functional. In such cases this address may not be known to all modules in the system.

Port Security

LOG_STD_NO_ACTION

BOOT_HOST_DHCP-6-INFO

6-Information

[chars]

This is an informational message generated while configuring a device via the dhcp feature.

-

LOG_STD_NO_ACTION

BOOT_HOST_DHCP-3-ABORTING

3-Error

[chars]

-

-

-

BOOT_HOST_DHCP-4-WARNING

4-Warning

[chars]

Configure a Device via DHCP feature has experienced an unexpected condition which did not cause a failure but suggests things did not go correctly.

-

LOG_STD_NO_ACTION

DWL-3-LOOP_BACK_DETECTED

3-Error

Loop-back detected on [chars].

Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network.

firmware

"Correct the problem causing the loopback " "condition. Then bring the port up by entering the shutdown " "then no shutdown interface configuration commands."

PHY-4-CHECK_SUM_FAILED

4-Warning

SFP EEPROM data check sum failed for SFP interface [chars]

The SFP was identified as a Cisco SFP but the system was unable to read vendor-data information to verify its correctness.

firmware

"Remove and reinsert the SFP. If it fails " "again in the same way the SFP may be defective."

PHY-4-MODULE_DUP

4-Warning

SFPs in [chars] and in [chars] have duplicate vendor-id and serial numbers

The SFP was identified as a Cisco SFP but its vendor ID and serial number match that of another SFP on the system.

firmware

LOG_STD_ACTION

PHY-4-EXCESSIVE_ERRORS

4-Warning

Excessive FCS data or idle word errors found on interface [chars]

The system has detected excessive FCS data word or idle word errors on the specified interface.

firmware

"Issue the <CmdBold>show interface<noCmdBold> " "command on the specified interface and check for CRC and " "other input errors. If errors are excessive issue the " "<CmdBold>shut<noCmdBold> command followed by the " "<CmdBold>no shut<noCmdBold> command to reset the interface."

PHY-4-BADTRANSCEIVER

4-Warning

An inappropriate transceiver has been inserted in interface [chars].

An inappropriate transceiver is inserted at the interface specified in the error message. This transceiver should not be used in this system.

firmware

"Remove the specified transceiver. If this " "transceiver was purchased from Cisco please contact " "Cisco TAC to get the transceiver replaced."

PHY-4-SFP_NOT_SUPPORTED

4-Warning

The SFP in [chars] is not supported

This SFP type is not supported on this switch.

firmware

LOG_STD_ACTION

PHY-4-SFP_PLUS_NOT_SUPPORTED

4-Warning

The SFP PLUS in [chars] is not supported

This SFP PLUS type is not supported on this switch.

firmware

LOG_STD_ACTION

PHY-4-UNSUPPORTED_TRANSCEIVER

4-Warning

Unsupported transceiver found in [chars]

The module was identified as an unsupported non-Cisco transceiver.

firmware

LOG_STD_ACTION

PHY-4-UNSUPPORTED_SFP_CARRIER

4-Warning

Unsupported SFP carrier module found in [chars]

The SFP carrier module was identified as an unsupported non-Cisco SFP carrier module.

firmware

"Remove the unsupported SFP and procure a " "supported module"

SYSCTLR-3-BAD_CALL

3-Error

Invalid parameter/mangled pointer\n routine: [chars] file: [chars] line: [dec]

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

SYSCTLR-3-SHELF_PROTO

3-Error

Shelf id protocol error

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

SYSCTLR-3-DISCOVER_SOCKET_OPEN

3-Error

socket open failed

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

SYSCTLR-3-DISCOVER_SOCKET_BIND

3-Error

socket bind failed

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

SYSCTLR-5-AUTH_FAILED

5-Notice

MD5 digest does not match SDP packet received from [inet] rejected

A SDP hello packet was received from shelf which is not trusted.

-

"Either specify the correct SDP password and/or destination on the\n\ shelf from which this message was received"

SYSCTLR-6-BAD_IP_ADDR

6-Information

Found Shelf [dec] with an invalid IP address [chars]

System Controller found a Shelf with an invalid ip address

-

"Check the IP address set on the Shelf"

SYSCTLR-6-SHELF_ADD

6-Information

Shelf [dec] discovered located at address [inet]

SDP protocol on system controller has detected a particular shelf.

-

""

SYSCTLR-6-SHELF_RESTORED

6-Information

Communication with shelf [dec] located at address [inet]

SDP protocol on system controller has detected a particular shelf.

-

""

SYSCTLR-4-SHELF_REMOVE

4-Warning

Shelf [dec] located at address [inet] removed.

SDP protocol on system controller didn't receive hello packets from particular shelf.

-

""

SYSCTLR-4-SHELF_RELOAD

4-Warning

Shelf [dec] located [inet] reloaded

SDP protocol on system controller has detected that a particular shelf has reload.

-

""

SYSCTLR-4-SHELF_CONF_CHANGED

4-Warning

Configuration for the shelf [dec] located [inet] changed

SDP protocol on system controller has detected that a particular shelf configuration has changed.

-

""

SYSCTLR-3-SHELF_MSGFAIL

3-Error

Unable to send message [dec] to process with pid [dec].

Most likely the performance collector process has terminated.

-

""

SYSCTLR-4-SDP_TIMEOUT

4-Warning

Hello packet from shelf [dec] not received shelf removed.

No SDP hello packets were received from the particular shelf this could indicate that particular router shelf is down or is mis-configured.

-

""

SYSCTLR-3-SDP_TIMER_ERROR

3-Error

No context associated with the expired SDP timer

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

SYSCTLR-4-SNMP_NOT_RESPONDING

4-Warning

Shelf [dec] not reachable via SNMP

Shelf indicated above is not responding to SNMP requests.

-

"Check the snmp configuration for the above shelf and also check correct \n\community string is specified in configuration command system-controller \n\community on the system controller."

SYSCTLR-3-INVALID_SDP_VERSION

3-Error

SDP packet received by system controller containted invalid version number.

Check that shelf is running compatible version of SDP

-

"If any of these messages recur call your technical support\n\ representative for assistance."

SYSCTLR-3-DUPLICATE_SHELF

3-Error

SDP packet with duplicate shelf-id [dec] received from [chars]already discovered \shelf located at [chars]

Two shelves with same shelf-id are configured in the system.

-

"Change the shelf-id for one of the shelf."

SYSCTLR-4-HMON_POLL

4-Warning

Local time [chars]\n [chars] on shelfid [dec] is not active resetting monitor_type [dec]\n

Health monitor setup commands polling information.\n\ If you see this message shows up every ten minutes that\n\ means health monitor is not able to set that corresponding \n\ entry on that shelf.

-

""

SYSCTLR-3-HMON_SETUP_FAILED

3-Error

Health monitoring setup failed on shelf_id [dec]\n

Health monitor failed to setup the monitoring command on that particular shelf

-

""

SHELF-5-AUTH_FAILED

5-Notice

MD5 digest does not match SDP packet received from [inet] rejected

A SDP hello packet was received from shelf which is not trusted.

-

"Either specify the correct SDP password and/or destination on the\n\ shelf from which this message was received"

SHELF-3-DISCOVER_SOCKET_OPEN

3-Error

socket open failed

An internal software error occurred.

-

LOG_STD_ACTION

SHELF-6-HELLO_PROCESS_START

6-Information

Shelf hello process has started.

This is an informational message only. An internal system controller\n\ process was started.

-

"Informational messages can be disabled by changing logging level."

SHELF-6-HELLO_PROCESS_STOP

6-Information

Shelf hello process has been stopped.

This is an informational message only. An internal system controller\n\ process completed its work.

-

"Informational messages can be disabled by changing logging level."

SHELF-6-SYSCTLR_ESTABLISHED

6-Information

Configured via system controller located at [inet]

This is an informational message only. Configuration information\n\ was received from a system controller.

-

"Informational messages can be disabled by changing logging level."

MPLSOAM-3-XDR_COMM

3-Error

[chars]:0x[hec] 0x[hec]

XDR Comm module - Unexpected RP/LC XDR condition encountered in MPLS OAM software. This may result in MPLS OAM FIB sub-blocks becoming out of synchronization between RP and LC. This should not affect overall system.

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-WALK_CONSUMED

3-Error

[chars]

FWD RPLC Module - Walk packet unexpectedly consumed in MPLS OAM software. This should not affect overall system performance.

mpls-oam

LOG_STD_ACTION

LSPV-3-COMM_UNKNOWN_RC

3-Error

Unexpected oce return code

Comm module - unexpected oce return code encountered

mpls-oam

LOG_STD_ACTION

LSPV-3-TP_ECHO_REQUEST

3-Error

MPLS-TP Echo request unsupported

MPLS-TP echo request was received. Ignoring as MPLS-TP is not supported on this platform

mpls-oam

LOG_STD_ACTION

MPLSOAM-3-UNAUTH_PROXY_REQ

3-Error

Unauthorized proxy request - dropping packet

MPLS-OAM proxy echo request was received. It was unauthorized and hence dropped.

mpls-oam

LOG_STD_ACTION

LDPLIB-3-GENERAL

3-Error

[chars]

Record associated with a withdrawn label has timed out before receiving acknowledgements from all peers.

mpls-ldp

"This is an informational message. This will not " "have any operational impact. The system will ignore any subsequently " "received release messages associated with the label."

LDPLIB-3-INIT

3-Error

Cannot allocate LIB

The LIB revision number used to manage advertisement of labels to LDP peers overflowed. This will result in faulty label distribution to LDP peers. The system recovers by toggling dynamic label switching off and on which forces the revision number to be re-initialized.

mpls-ldp

"None required."

LDP-3-GENERAL

3-Error

[chars]

-

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-3-CONSISTENCY

3-Error

[chars]

-

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-5-INFO

5-Notice

[chars]

This is an informational message generated by the Label\n\ Distribution Protocol LDP implementation.

mpls-ldp

ACTION_LOOPING_LSP

LDP-3-PTCLREAD

3-Error

peer [chars] read failure

An error occurred while attempting to read a LDP PDU received\n\ from a peer.

mpls-ldp

ACTION_NEW_SESSION_TDP

LDP-5-IDENT

5-Notice

cannot set [chars][chars] LDP ident

-

mpls-ldp

"This is an informational message. As long as it needs to set\n\ its chassis LDP identifier the system will periodically\n\ attempt to do so until it succeeds. If this message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative."

LDP-3-SM

3-Error

unexpected event: peer [chars][chars] state=[chars] event=[chars][chars]

An operation on the state machine for a LDP peer failed.

mpls-ldp

ACTION_IGNORE_REST_OF_PIE_TDP

LDP-3-KA_NOMEMORY

3-Error

Can't alloc KA message

An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP Keep Alive protocol message has failed.

mpls-ldp

"The system will continue by omitting transmission of the LDP\n\ Keep Alive Message. This may result in termination of one or more\n\ LDP sessions as the peers time out the sessions. If this\n\ message persists reduce other system activity if possible\n\ and call your technical service representative for\n\ assistance."

LDP-3-TAGATM_BAD_RANGE

3-Error

Interface [chars] Bad VPI/VCI range. Can't start a LDP session

The session parameters proposed by an LDP peer differ from those\n\ preferred by the platform. The differences are not sufficient to\n\ prevent the LDP session from being established but may have an\n\ impact on label distribution operation

mpls-ldp

"If the parameters identified relate to the optional path vector-based\n\ loop detection mechanism note that the IETF LDP specification\n\ recommends that when Loop Detection is enabled in a portion of a\n\ network it is recommended that all LSRs in that portion of the\n\ network be configured with Loop Detection enabled and with the\n\ same path vector limit. If the parameters identified relate\n\ to some other aspect of the LDP session and the message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative."

LDP-3-TAGATM_NOMEM

3-Error

Interface [chars] Resource failure. Can't start a LDP session

An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP TAGATM VPI/VCI ranges has failed.

mpls-ldp

"The system will not be able to create a LDP session between\n\ the affected LDP peers. If this message persists reduce \n\ other system activity if possible and call your technical \n\ service representative for assistance."

LDP-5-ACL

5-Notice

mpls ldp advertise-labels has no effect for lc-atm

EXPLANATION_ACL_TDP

mpls-ldp

"No action is required."

LDP-5-ACL1

5-Notice

mpls ldp advertise-labels has no effect for lc-atm

EXPLANATION_ACL_TDP

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-4-PTCL

4-Warning

peer [chars] [chars]

A violation of the LDP protocol by a LDP peer has been detected.

mpls-ldp

ACTION_NEW_SESSION_TDP

LDP-4-ADV

4-Warning

Label advertisement mode DU/DoD mismatch with peer [chars] resolved to [chars].

-

mpls-ldp

ACTION_NEW_SESSION_TDP

LDP-5-CLEAR_CHKPT

5-Notice

Clear [chars] checkpoint state [chars] by [chars]

Checkpoint state for one or more LDP objects has been reset

mpls-ldp

LOG_STD_NO_ACTION

LDP-3-ISYNC_CHKPT

3-Error

[chars]:: [chars] request failed [chars]

An unexpected condition happened while uncheckpointing

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-3-ISSU_XFORM

3-Error

ISSU [chars] transformation failed for msg type [dec][chars].

-

-

-

LDP-3-AUTOCFG

3-Error

Interface [chars] is in an unexpected autoconfig state 0x[hec] [chars] request.

An interface is in an unexpected LDP auto config state. This could\n\ impact the LDP session running on this interface

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-3-ISYNC

3-Error

[chars]

An unexpected error happened in LDP-IGP Synchronization operation.

mpls-ldp

ACTION_COPY_REPORT_TDP

LDP-5-NBRCHG

5-Notice

[chars] Neighbor [chars] is [chars][chars]

An LDP neighbor has either come up or gone down. The message\n\ describes the change for it.

mpls-ldp

"This informational message normally appears as routers and\n\ LDP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated."

LDP-5-CLEAR_NBRS

5-Notice

Clear LDP neighbors [chars] by [chars]

One or more LDP neighbor sessions has been reset

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-GR

5-Notice

[chars]

An informational LDP notice was generated for a Graceful Restart event.

mpls-ldp

LOG_STD_NO_ACTION

LDP-3-RECONNECT

3-Error

[chars]

An error occurred while parsing the incoming LDP Initialization message.\n\ The FT Reconnect Timer value received was greater than\n\ the locally-configured Forwarding State Holding Timer value.

mpls-ldp

"Reconfigure the Forwarding State Holding Timer value."

LDP-4-PWD

4-Warning

MD5 protection is required for peer [chars] no password configured

-

mpls-ldp

"This message indicates a misconfiguration on the router. If the\n\ user requires MD5 password protection for the LDP session configure\n\ a password for the LDP peer. If the user requires MD5 password\n\ protection for a subset of LDP neighbors but not for this specific\n\ LDP peer modify the LDP password configuration to exclude this LDP\n\ peer from the password required list. Otherwise if an LDP session\n\ should not exist disable MPLS to this neighbor."

LDP-5-SP

5-Notice

[chars]

An informational LDP notice was generated for a Session Protection event.

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-PWDCFG

5-Notice

Password configuration changed for [chars]

An informational LDP notice was generated to report password\n\ configuration change for a neighbor.

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-PWDRO

5-Notice

Password rolled over for [chars]

An informational LDP notice was generated to report lossless password\n\ change for a neighbor.

mpls-ldp

LOG_STD_NO_ACTION

LDP-5-PWDKEYTRUNC

5-Notice

MD5 digest uses [dec] chars of longer [chars] keys for peer [chars]

-

mpls-ldp

"This message indicates a possible misconfiguration on the router.\n\ Ensure that you have configured your key chains correctly on each\n\ router. Your LDP session can be established if the MD5 key used by\n\ the specified LDP peer has been truncated by the same amount or is\n\ defined to be equal to the truncated key value on this router."

LDP-5-UNKNOWNCAP

5-Notice

Advertised Capability [chars] not supported by peer [chars]

This information message is returned by peer to assist in\n\ troubleshooting interop issues that may arise when a peer is\n\ not capable of supporting an advertised LDP capability

mpls-ldp

LOG_STD_NO_ACTION

LDP-4-CAPCHANGE

4-Warning

Reset of established LDP sessions required to propagate [chars]

A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers will not learn of the change until the LDP session has\n\ been reset.

mpls-ldp

"Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command."

LDP-4-CAPCHANGE_DYNAMIC

4-Warning

Reset of established LDP session required to propagate [chars]\n change to peers that don't support Dynamic Announcement

A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers that don't support Dynamic Announcement will not learn\n\ of the changeuntil the LDP session has been reset.

mpls-ldp

"Use the 'show mpls ldp neighbor capability' command to determine\n\ which neighbors need to be reset. Reset LDP neighbor using the\n\ 'clear mpls ldp neighbor ...' command."

LDP-4-MAXMSGSIZE

4-Warning

Maximum implementation message size exceeded actual [dec] maximum [dec]

This is an informational message that appears when LDP receives\n\ a request to allocate memory resources for an LDP message with\n\ a size exceeding the current implemented maximum.

mpls-ldp

"No action is required unless a larger message size is deemed to be\n\ required to support a new application. In this case the actual\n\ application should be identified and component owners contacted\n\ to increase the implemented maximum message size."

LLIST-3-ONLIST

3-Error

[chars] to 0x[hec] 0x[hec] on list

An internal inconsistency was detected when an attempt was made to\n\ add an item to a list already on the list.

tag-switch

"Copy the message exactly as it appears and report it to your technical\n\ service representative."

LLIST-3-OFFLIST

3-Error

[chars] from 0x[hec] 0x[hec] not on list

An internal inconsistency was detected when an attempt was made to\n\ remove an item from a list not on the list.

tag-switch

"Copy the message exactly as it appears and report it to your technical\n\ service representative."

LCON-3-CONSISTENCY

3-Error

[chars]

An action attempted by the Label Control process encountered\n\ an unexpected condition.

mpls-ldp

"The request will be ignored. If it repeatedly occurs\n\ copy the message exactly as it appears and report it to your\n\ technical service representative."

LCON-3-ALLOC

3-Error

Cannot alloc [chars]

An attempt to allocate a LDP data structure failed\n\ because of a low memory condition.

mpls-ldp

ACTION_STD_LOW_MEMORY_TAGCON

LCON-3-PROCESS

3-Error

process not created

An attempt to create the label distribution and control process\n\ failed. The probable cause is insufficient memory.

mpls-ldp

ACTION_STD_LOW_MEMORY_TAGCON

LCON-3-INIT

3-Error

process cannot initialize

The label distribution and control process failed to initialize\n\ itself. The probable cause is insufficient memory.

mpls-ldp

ACTION_STD_LOW_MEMORY_TAGCON

LCON-4-INIT_TAG_ALLOC

4-Warning

Failure to initialize label allocation pool [dec]

The system was unable to initialize the data structure used to support\n\ allocation of labels for label switching for the specified label pool.

mpls-ldp

-

LCON-5-SEND

5-Notice

cannot queue LDP [chars] message for [chars][chars]

-

mpls-ldp

"This is an informational message. Failure to queue a message for\n\ a peer should occur only when the LDP session with the peer no\n\ longer exists. The software should recover from this\n\ situation by discarding the LDP session and trying to\n\ establish a new one. If this message occurs repeatedly copy\n\ it exactly as it appears and report it to your technical\n\ service representative."

LCON-3-PEERSM

3-Error

LDP peer [chars][chars]: [chars]

An operation on the state machine for the label distribution and\n\ control process failed.

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-DEADADJ

3-Error

[chars] [chars]

An unexpected failure occurred while building a LDP protocol\n\ message for transmission to a LDP peer. It occurred when\n\ attempting to add a label binding or an address to the message.

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-RADIXTREE

3-Error

[chars]LIB walk failed [chars]

-

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-LDPID

3-Error

peer [chars] LDP Id/Addr mapping problem [chars]

EXPLANATION_ADDR_TBL_TAGCON

mpls-ldp

ACTION_TOGGLE_TAG_IP_TAGCON

LCON-3-DUP_ADDR_RCVD

3-Error

Duplicate Address [chars] advertised by peer [chars] is already bound to [chars]

EXPLANATION_ADDR_TBL_TAGCON

mpls-ldp

ACTION_TOGGLE_TAG_IP_TAGCON

LCON-3-DEFCASE_BINDING_PIE

3-Error

Unexpected blist_type [dec] for [chars] message from peer [chars]

A LDP protocol message received from a LDP peer contained an\n\ unexpected binding list type. The message will be be ignored.

mpls-ldp

ACTION_IGNORE_PIE_TAGCON

LCON-3-REGISTRY

3-Error

Unexpected [chars] for reg_invoke_[chars]

-

mpls-ldp

-

LCON-4-ADDR_PROC

4-Warning

Can't create lcon addr proc

-

mpls-ldp

"This is an informational message. As long as it needs the\n\ process the system will regularly attempt to create it. If\n\ this message occurs repeatedly copy it exactly as it appears\n\ and report it to your technical service representative."

LCON-4-ADDRQ

4-Warning

Can't alloc work item for [chars]

-

mpls-ldp

"This is an informational message. The system remembers that\n\ it needs to do this work and will regularly attempt to queue\n\ the necessary work item. If this message occurs repeatedly\n\ copy it exactly as it appears and report it to your technical\n\ service representative."

LCON-3-EVENTQ

3-Error

Can't alloc work item for [chars]

An operation on the LDP Directed Adjacency data structure\n\ failed.

mpls-ldp

ACTION_COPY_REPORT_TAGCON

LCON-3-LATREVNUMWRAP

3-Error

Label Local Address Table revision number wrapped

The revision number used to manage advertisement of interface\n\ addresses to LDP peers overflowed. This will result in faulty\n\ advertisement of interface addresses to LDP peers and\n\ faulty label switching on those peers.

mpls-ldp

"To restore proper interface address advertisement reboot the\n\ platform. Report this condition to your technical service\n\ representative."

LCON-3-LCLTAG_ALLOC

3-Error

Cannot allocate local label

-

mpls-ldp

"The number of labels available for allocation can be changed\n\ by the <CmdBold>mpls label range ...<NoCmdBold> configuration command.\n\ Consult with your technical service representative to determine\n\ whether you should use this command to increase the number of\n\ available labels."

LCON-3-LABEL_REGION

3-Error

Platform specified information for label region [chars] is invalid.

A platform service routine provides label region information about\n\ all label regions it supports. This error message is printed when\n\ the service routine does not specify its label region information\n\ correctly.

mpls-ldp

"Report this condition to your technical service representative."

LCON-4-CFGD_LBL_REGION

4-Warning

Adjusting configured label range to default range

The saved configuration has been ignored and the default label range\n\ is being used.

mpls-ldp

"Please reconfigure the label range to a valid range using <CmdBold>\n\ mpls label range ... <NoCmdBold> configuration command."

MPLS_TE-3-SIGNALLERINIT

3-Error

Signaller unable to [chars]register RSVP [chars]

A message handler used by the signaller to receive events or requests from RSVP could not be installed or removed.

mpls-te

"Copy and save the message. If possible re-start " "the TSP tunnel signalling process by issuing the " "no tag-switching tsp-tunnels command followed by " "the tag-switching tsp-tunnels command. If the " "message continues to occur even after re-starting " "the signalling process several times then contact " "your technical support representative for " "assistance."

MPLS_TE-3-TUNNELKILL

3-Error

Tunnel removal attempt by [chars] failed for tunnel [chars]: [chars]

-

-

-

MPLS_TE-3-CONSISTENCY

3-Error

[chars]: [chars] [chars] [chars]

An action attempted by the traffic engineering tunnel implementation encountered an unexpected condition

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-4-LSPREJECT

4-Warning

LSP [chars] rejected: matching passive TE tunnel [chars]

An RSVP Path message for an LSP for a tunnel was rejected with a PathErr message due to the absence of a properly configured MPLS passive tunnel interface which is administratively up.

mpls-te

"Create and/or properly configure an MPLS passive tunnel interface " "which will match the rejected LSP and ensure that it is " "administratively up or modify the tunnel interface configuration " "at the head end of the tunnel."

MPLS_TE-5-LSP

5-Notice

[chars]

An informational traffic engineering tunnel trap was generated for an LSP event.

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-5-TUN

5-Notice

[chars]

An informational traffic engineering tunnel trap was generated for a Tunnel event.

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-5-FRR

5-Notice

[chars]

An informational traffic engineering tunnel trap was generated for an MPLS Fast-Reroute event.

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-3-PHYSINTFCDOWN

3-Error

[chars]'s LSP interface [chars] did not come up after [dec] msecs

The underlying interface for a tunnel LSP did not come up although the tunnel itself is up.

mpls-te

"See if the underlying interface is physically connected."

MPLS_TE-3-MFIERROR

3-Error

[chars]: [chars] [chars]

A traffic engineering request to the label switching database encountered an unexpected condition

mpls-te

"Copy the message exactly as it appears and report it to your " "technical service representative."

MPLS_TE-2-BUNDLE_INSERT

2-Critical

[chars] [chars]

Request for inserting a traffic engineering tunnel bundle failed.

mpls-te

LOG_STD_ACTION

MPLS_TE-2-UNSUPPORTED_LINK_TYPE

2-Critical

[chars]

Unsupported link type

mpls-te

LOG_STD_ACTION

MPLS_TE-2-ADJ_WALK_ERR

2-Critical

[chars]

Error during bundle adjacency walk

mpls-te

LOG_STD_ACTION

MPLS_TE-4-CONFLICT_BIDIR_CFG

4-Warning

[chars]

Conflicting bidirectional association configuration

mpls-te

"Re-check tunnel configuration and make sure destination of tunnel" "is properly set and the bidirectional association is unique against" "all tunnels."

MPLS_TE-4-PCEP_REPORT_FAILED

4-Warning

LSP TID:[dec] LID:[dec] wasn't reported to the PCE server

-

-

-

MPLS_TE-4-PCEP_REQUEST_FAILED

4-Warning

Unable to request path for LSP TID:[dec] LID:[dec] from PCE server

-

-

-

MPLSIFMIB-3-GENERAL

3-Error

[chars]

Probable memory corruption of mpls layer subblock -- cause unknown.

mpls-mib

LOG_STD_ACTION

TBRIDGE-4-GIANT

4-Warning

Giant received on [chars] [dec] exceeds [dec]\n DA [enet] SA [enet] [0x%08x]

-

-

"Use the address and packet information provided to trace the source of\n\ these packets and reduce its MTU to conform to the standard for the\n\ given media."

TBRIDGE-4-NOVCDROP

4-Warning

Destination VC unknown for packet

A transparently bridged packet destined for an ATM interface cannot be\n\ fully addressed.

-

"Clear the bridge table to force re-learning of all addresses."

TBRIDGE-4-NOVCFLOOD

4-Warning

No VC's configured for bridging on [chars]

An ATM interface was configured for transparent bridging without also\n\ specifying the associated virtual circuits.

-

"Configure the required virtual circuits on the specified interface."

TBRIDGE-4-VCPAKDROP

4-Warning

Subscriber SA [enet] moved or loop between circuits [dec] and [dec]

A subscriber bridged packet dropped because potential circuit loop\n\ or roaming host at subscriber end of network.

-

"Clear bridge table. If problem persists it is not a roaming host but\n\ a loop between virtual circuits at subscriber end of network. Take\n\ looping virtual circuits out of service and/or shut the software\n\ interface they are on while subscriber is contacted to remove loop\n\ condition at subscriber end of network."

TBRIDGE-4-INVALIDMEDIA

4-Warning

[chars] received on [chars] - invalid media for transparent bridging

Transparent bridging was configured on an interface that does not\n\ support it.

-

"Remove transparent bridging from the configuration on the specified\n\ interface."

TBRIDGE-4-SMF_ACTION

4-Warning

invalid action found for [enet] on [chars] - %08x

A software or hardware error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

TBRIDGE-4-BAD_ENCAP

4-Warning

Unexpected encapsulation received on [chars] [chars]

The transparent bridging driver received a packet with\n\ unrecognizable encapsulation. The packet had to be discarded.

-

"This could indicate a network media error or that a protocol\n\ which is newer than this version of the Cisco IOS software is\n\ being used. If it is believed that the dropped packets are of\n\ a real protocol upgrade to a new version of the software which\n\ handles it."

TBRIDGE-4-BADXMAC

4-Warning

XMACACCESS: Invalid extended access list [dec]

This is a configuration problem. The specified extended access\n\ list either does not exist or contains an error.

-

"Correct the configuration problem."

TBRIDGE-4-BTELIMITREACHED

4-Warning

MAC-address table size limit %lu entries reached

The total number of bridge MAC-address table entries across all bridge \n\ groups has reached the configured maximum limit.

-

"Check the bridge tables to determine the origin of the bridge MAC-address \n\ table entries. Check the network configuration and ensure that the entries \n\ are as expected. Use the bridge mac-address-table limit <n> configuration \n\ command to either increase the maximum limit or to disable limit-checking \n\ altogether."

TCAM_MGR-3-MALLOC_FAIL

3-Error

[chars] [chars]

-

-

""

TCAM_MGR-3-BAD_LAST_DYN_REGION

3-Error

[dec]

-

-

""

TCAM_MGR-3-BAD_FIRST_DYN_REGION

3-Error

[dec]

-

-

""

TCAM_MGR-3-INVALID_OPERATION

3-Error

[chars] [dec]

-

-

""

TCAM_MGR-3-INVALID_REG_TYPE

3-Error

[chars] [dec]

-

-

""

TCAM_MGR-3-INTERNAL_ERROR

3-Error

[chars] [chars] [dec]

-

-

""

TCAM_MGR-3-OP_FAIL

3-Error

[chars] failed for application [chars] application entry [hec] with [chars] error

-

-

""

TCAM_MGR-3-UNUSUAL_BUG_WARNING

3-Error

[chars] mbu [hec] free_array_index [dec] region_id [dec]

-

-

""

TN-3-READLINE

3-Error

Unknown return code [dec] from telnet_readline

An internal software error occurred.

-

"If any message recurs call your technical support representative " "for assistance."

TN-3-BADSTATE

3-Error

Illegal state [dec]

An internal software error occurred.

-

"If any message recurs call your technical support representative " "for assistance."

TN-2-BADLOGIN

2-Critical

Bad login string pointer [hex]

An internal software error occurred.

-

"If any message recurs call your technical support representative\n" "for assistance."

TN-2-BADCONN

2-Critical

Bad conn pointer [hex] closing all connections on terminal line [dec]

An internal software error occurred.

-

"If any message recurs call your technical support representative\n" "for assistance."

RCMD-4-RCPATTEMPTED

4-Warning

Remote copy from [chars] at [chars] denied

An attempt was made to connect to a router through RCP but the router\n\ was not configured as an RCP server.

-

"Configure an RCP server."

RCMD-4-RSHATTEMPTED

4-Warning

Remote shell from [chars] at [chars] denied

An attempt was made to connect to a router through rsh but the router\n\ was not configured as an rsh server.

-

"Configure an rsh server."

RCMD-4-RCMDDNSFAIL

4-Warning

DNS hostname/ip address mismatch. [chars] unknown to DNS

The IP address for an incoming rcmd request is not registered with\n\ DNS.

-

"Add the IP address to DNS."

FTPSERVER-4-XFER_WARNING

4-Warning

File may not have transferred correctly

Extra linefeeds were received in ASCII mode

-

-

FTPSERVER-6-CWDFAILED

6-Information

setcwd failed [chars].

FTP client request failed to change to requested directory.

-

"Verify correct path for desired directory."

FTPSERVER-6-NEWCONN

6-Information

FTP Server - new connection made.

An new ftp server connection has opened.

-

"FTP Server connections can be disabled by config 'no ftp-server enable'."

FTPSERVER-6-REPLYLOGN

6-Information

REPLY [dec]

This is an informational message only.\n\ An FTP login has occurred.

-

"Informational messages can be disabled by changing logging level."

FTPSERVER-6-REPLYLOGTEXT

6-Information

[dec][chars]

This is an informational message only.\n\ This text was sent to the FTP client.

-

"Informational messages can be disabled by changing logging level."

FTPSERVER-6-NETWRTFAILED

6-Information

FTP Server:connection / tcp_write failed.

A TCP write failed while sending an FTP command reply to the client.

-

"Verify network connection from client to server and verify ftp client operation."

FTPSERVER-6-TOPDIRTEST

6-Information

Input path failed Top-dir[chars] test.

An operation attempted to use a path not within the tree under the ftp-server topdir config parameter.

-

"Re-configure the server 'topdir' parameter or select another path."

FTPSERVER-6-CONNCLOSED

6-Information

Connection closed after [dec] seconds. '[chars]'

The FTP connection to a client was closed after 5 minutes inactivity.

-

"Client inactivity will cause the server to shutdown the connection."

FTPSERVER-6-NETRDFAILED

6-Information

FTP control connection / tcp_read failed.

An error occured reading the command line from the ftp client.

-

"Verify network connection from client to server and verify ftp client operation."

XXX-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

flexible-netflow

LOG_STD_ACTION

TN3270-2-INP_OVF1

2-Critical

Input Buffer overflow

-

-

"Copy this error message exactly as it appears and contact your\n\ technical support representative for assistance."

TOPN_COUNTERS-4-MEM_UNAVAIL

4-Warning

Memory was not available for handling the TopN request

The system is unable to handle the TopN request because of lack of memory.

-

"Reduce other system activity to ease memory demands. If conditions warrant upgrade to a larger memory configuration."

TOPN_COUNTERS-5-STARTED

5-Notice

TopN collection for report [dec] started by [chars]

The TopN report that was requested by the specified user starts with the specified report number.

-

LOG_STD_NO_ACTION

TOPN_COUNTERS-5-AVAILABLE

5-Notice

TopN report [dec] is available

The specified report is ready and can be viewed by the users.

-

LOG_STD_NO_ACTION

TOPN_COUNTERS-5-DELETED

5-Notice

TopN report [dec] deleted by [chars]

The specified report has been deleted by the specified user.

-

LOG_STD_NO_ACTION

TOPN_COUNTERS-5-KILLED

5-Notice

TopN report [dec] task killed by [chars] [chars]

The system was in the process of generating the specified report but the specified user terminated the report before its completion.

-

LOG_STD_NO_ACTION

TOPN_COUNTERS-5-NOPORTS

5-Notice

No interfaces in the system match the interface type for the generation of the topN report [dec]

There were no interfaces in the system which matched the interface type selected in the specified report.

-

LOG_STD_NO_ACTION

TRANSCEIVER-6-REMOVED

6-Information

Transceiver module removed from [chars]

The online insertion and removal OIR facility detected the

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-6-INSERTED

6-Information

transceiver module inserted in [chars]

The online insertion and removal OIR facility detected a

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-3-CHECKSUM_ERROR

3-Error

Detected in the transceiver module in [chars] module disabled

A checksum error was detected when reading the ID PROM of a transceiver module for the interface specified in the error message. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. If the problem persists LOG_STD_ACTION."

TRANSCEIVER-3-IMPROPER_INSERTION

3-Error

Transceiver module in [chars] not fully inserted remove the transceiver and re-insert with proper seating lock.

An initialization failure occurred for the transceiver module for the interface specified in the error message. This condition is caused by improper insertion of transceiver As a result of the error the module is disabled.

spa-infra

"Try OIR'ing the module and reseat properly. "

TRANSCEIVER-3-INIT_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

An initialization failure occurred for the transceiver module for the interface specified in the error message. This condition could be caused by software firmware or hardware problem. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-NOT_COMPATIBLE

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is not compatible with the interface. As a result of the error the module is disabled.

spa-infra

"Replace the module with a compatible transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_IDENTIFIED

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message could not be identified and may not be compatible with the interface. As a result of the error the module is disabled.

spa-infra

"Replace the module with a compatible transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_SUPPORTED

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is not a cisco supported module. As a result of the error the module is disabled.

spa-infra

"Replace the module with a cisco supported transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-ATTACH_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

A software device driver attach failed. This condition could be caused by software firmware or hardware problem but a software or firmware problem is more likely. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-SM_CREATION_FAILURE

3-Error

Transceiver OIR State Machine creation failed for [chars] module disabled.

A state machine could not be created for the transceiver OIR operation. If a %SYS-2-MALLOCFAIL message was also received with this message this condition indicates insufficient system memory. Other possible causes include invalid subblock pointer.

spa-infra

"If it is insufficient system memory " LOG_STD_REDUCE_ACTION "If this message recurs " LOG_STD_ACTION

TRANSCEIVER-3-OPER_ENABLE_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

Failed to enable the transceiver module for the interface specified in the error message. This condition could be caused by software firmware or hardware problem. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-RPC_PROCESSING_ERROR

3-Error

Transceiver RPC error: [chars]

Non Fatal error occured in processing an RPC messsage.

spa-infra

show version

TRANSCEIVER-3-RPC_INIT_FAIL

3-Error

Transceiver RPC init failure

The system failed to create the resources required to process user\n\ interface commands for transceivers. The error is not fatal but some \n\ \show\ commands could fail.

spa-infra

show version

TRANSCEIVER-3-RPC_FAILED

3-Error

Application error rc = [dec] in port [chars]

The system failed to retrieve the information required to execute\n\ the comand

spa-infra

show version

TRANSCEIVER-3-DEV_PLUGGABLE_OPTICS

3-Error

Transceiver [chars] table internally inconsistent @ 0x[hec]

One of the transceiver attribute table is not properly updated.

spa-infra

"This is a debug message."

TRANSPORT-3-INIT_FAILED

3-Error

Transport map collection initialization failed\n

The system was unable to allocate memory for storing transport maps. Configuration of transport maps will be unavailable.

transport

show memory

CHAT-3-CANTRUN

3-Error

[t-line] in use can't run startup script

When the startup script attempted to run it found another process had\n\ Already been started on the line

chat

"Remove startup script from line configuration if it's inappropriate.\n\ Report to cisco."

LPD-3-MANYLF

3-Error

Line [t-line] packet has too many newlines to convert

An internal buffer did not have enough room to add all the necessary\n\ carriage returns to a packet of LPD data destined for a printer\n\ configured with a newline-convert command. This message is unlikely to\n\ occur with a file containing valid data.

-

"Check the file being printed to see whether it contains valid\n\ printable data."

TTY-3-AUTOCONFIG

3-Error

TTY[t-line]: Modem auto-configuration failed

Modem auto-configuration failed either because the modem rejected\n\ the configuration string or because of a timeout. An attempt\n\ should be made to apply the configuration string mannually.

-

LOG_STD_ACTION

TTY-3-NOPROCESS

3-Error

Cannot create [chars] process

Failed creating the process.

-

LOG_STD_ACTION

TMQ-3-NOTFOUND

3-Error

TMQ Attempt to delete entry not in queue

An attempt was made to delete an entry not in the queue.

-

"Advisory message only. No action required."

TTYDRIVER-2-NOBUF

2-Critical

Unable to allocate [dec] I/O buffers

-

-

-

TTYDRIVER-2-NOMEM

2-Critical

Unable to allocate [dec] byte status block

-

-

-

TTYDRIVER-2-NOBUFPOOL_ASYNC

2-Critical

Unable to create buffer pool for async. mode interface

-

-

-

TTYDRIVER-2-NOBRKPAK

2-Critical

Unable to allocate break block from I/O mem

-

-

-

PARSE_RC-3-PRC_LEV_RANGE

3-Error

Parser Return Code level range error [dec]

An internal software error occurred.

-

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

PARSE_RC-3-PRC_SUBRCODE_RANGE

3-Error

Parser Return Code state range error [dec]

An internal software error occurred.

-

"Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance."

PARSE_RC-3-PRC_INVALID_CSB

3-Error

-

An internal software error occurred.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_INVALID_BLOCK_PTR

3-Error

-

An internal software error occurred.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_OUT_OF_RANGE_ENUM

3-Error

[chars] had value [dec]

An out-of-range parameter was passed to an internal API.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_UNRECOGNIZED_ERROR

3-Error

error value `[dec]' is not currently mapped

An unrecognized error was caught and remapped.

parser

LOG_STD_ACTION

PARSE_RC-3-PRC_INTERRUPT

3-Error

[chars]

An internal software error occurred.

parser

LOG_STD_ACTION

PARSE_RC-4-PRC_NON_COMPLIANCE

4-Warning

`[chars]'

An internal software error occurred.

smartport

LOG_STD_ACTION

AUTOSEC-3-CONFSAVE_FAIL

3-Error

Applying AutoSecure config to running-conf failed with error [dec]

Configuration of the AutoSecure session could not be applied to the running configuration

security keyword:autosec

LOG_STD_ACTION

AUTOSEC-5-ENABLED

5-Notice

AutoSecure is configured on the device

Security configuration of the device is done using AutoSecure.

none

"Notification message only. No action required."

USB_TOKEN-3-USB_TOKEN_NOMEM

3-Error

No available memory for [chars]

Memory allocation failure.

usb-token

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

USB_TOKEN-3-USB_TOKEN_MSG_FAILURE

3-Error

Failure in handling USB Security Token insertion/removal event

Retrieving Token insertion/removal message failed in Token Daemon

usb-token

"Remove the token and insert it back. If the problem still persists\n\ report the problem to your technical support representative along\n\ with the output of \"show usb device\" \"show usb controller\" and\n\ \"show file systems\" commands."

USB_TOKEN-3-USB_TOKEN_SEMCREATE_FAILURE

3-Error

Failure in creating USB Security Token semaphore

Watched semaphore creation failed

usb-token

"Report the problem to your technical support representative along\n\ with the output of \"show usb device\" and \"show usb controller\" commands."

USB_TOKEN-3-USB_TOKEN_MAX_TOKENS_INSERTED

3-Error

Unavailable USB Security Token slot

Maximum number of tokens that can be supported are already inserted

usb-token

"Remove the other tokens that are not in use. And remove and insert this token again."

USB_HOST_STACK-5-USB_ENUM_FAIL_NOPOWER

5-Notice

Failed to enumerate a USB device as the device's power requirement[dec] mA is more than the available port power[dec] mA

The device's power requirement exceeds the available port power.

usb-driver

"Refer platform specific documents on the maximum power provided on USB ports."

USB_HOST_STACK-5-USB_ENUM_FAIL_GETDESCR

5-Notice

Failed to enumerate a USB device as not able to read the device's description.

Unable to read Device descriptor information from the device

usb-driver

"The device may be faulty."

USB_HOST_STACK-5-USB_ENUM_FAIL_ADDRFULL

5-Notice

Failed to enumerate a USB device as the address pool is full.

The USB address pool is full.

usb-driver

"The number of inserted devices might have exceeded the platform limit. Remove the other devices that are not in use. And remove and insert this device again."

USB_HOST_STACK-5-USB_ENUM_FAIL_SETADDR

5-Notice

Failed to enumerate a USB device as not able to do set device's address.

The setting of USB address to the device failed.

usb-driver

"The device may be faulty."

USB_HOST_STACK-5-USB_ENUM_UNSUPPORTED_DEVICE

5-Notice

Unsupported device inserted. Host id [dec] Device Addr [dec].

The device is not supported on the platform/image.

usb-driver

"This device is not supported. Use \"show usb device\" to see " "the device information. Check the image and see whether the " "image supports the device."

USB_HOST_STACK-2-USB_NO_MEMORY

2-Critical

Memory allocation failure: [chars].

Unable to allocate memory for USB stack structures.

usb-driver

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

USB_HOST_STACK-5-USB_NO_HUB_SUPPORT

5-Notice

USB Hub is not supported.

USB Hub is not supported on the platform.

usb-driver

"Do not use USB Hub since it is not a supported device."

USB_HOST_STACK-3-USB_FLASH_READY_TEST_FAILED

3-Error

USB flash failed to pass 'Ready' test.

The USB Flash memory failed diagnostic testing. The Flash memory could not enter the Ready state and was not registered in the file system.

usb-driver

"Remove the device and reinsert it again. If the problem persists" "please search Bug Toolkit on the Cisco web site for" "bugs related to your version of software. If you do" "not find an existing bug please open a TAC case and" "provide 'show version' 'show running' and 'show usb device'"

USB_HOST_STACK-6-USB_FLASH_READY_TEST_TIME

6-Information

USB flash 'Ready' test time over [dec] seconds.

The USB Flash memory has taken a time equal to or more than 75% of the maximum time allotted for it to pass the diagnostic testing and enter the Ready state.

usb-driver

LOG_STD_NO_ACTION

USB_HOST_STACK-6-USB_DEVICE_CONNECTED

6-Information

A [chars] USB device has been inserted in port [dec].

This is an informational message sent when an interrupt is generated to the USB controller upon device insertion.

usb-hcd

LOG_STD_NO_ACTION

USB_HOST_STACK-6-USB_DEVICE_DISCONNECTED

6-Information

A USB device has been removed from port [dec].

This is an informational message sent when an interrupt is generated to the USB controller upon device removal.

usb-hcd

LOG_STD_NO_ACTION

USB_HOST_STACK-3-USB_HOST_SYS_ERROR

3-Error

A USB host controller sys error happened[hec] [hec].

This is an informational message sent when a system error happened on the the host controller. USB host controller resetted

usb-hcd

LOG_STD_NO_ACTION

USBFLASH-5-CHANGE

5-Notice

[chars] [chars]

A USB device has been inserted/removed

-

LOG_STD_NO_ACTION

USBFLASH-4-FORMAT

4-Warning

[chars] [chars]

The usb flash device does not have a recognizable format There are unexpected values in the partition table or boot sector This device needs formatting in the router before use.

-

"Follow any instructions provided in the error " "message before storing any file to this USB flash device"

USBFLASH-3-DEVOPEN

3-Error

[chars] [chars]

An application handle for the usb flash could not be retrieved.

-

"Please search Bug Toolkit on the Cisco web site for" "bugs related to your version of software. If you do" "not find an existing bug please open a TAC case and" "provide 'show version' & 'show running'"

USBFLASH-3-DEVSTARTSTOP

3-Error

[chars] [chars]

The usb flash device could not be stopped and restarted.

-

"Please search Bug Toolkit on the Cisco web site for" "bugs related to your version of software. If you do" "not find an existing bug please open a TAC case and" "provide 'show version' & 'show running'"

USBFLASH-3-IFSCREATE

3-Error

[chars] [chars]

The usb flash device could not be registered with the internal file system.

-

"Please search Bug Toolkit on the Cisco web site for" "bugs related to your version of software. If you do" "not find an existing bug please open a TAC case and" "provide 'show version' & 'show running'"

USBFLASH-5-DIBERR

5-Notice

USB Flash device [chars] [chars]

The system cannot boot a image from the USB Flash device because the Device Information Block is different. The USB Flash device can be read by the router but will require formatting by the router before an image can be booted from it.

-

"Follow any instructions provided in the error " "message. Before storing a image in the USB Flash device " "and trying to boot from this device enter the " "format command to format the flash device from the " "router. Then copy the desired image to the Flash " "device and then boot from this device."

USB_PRINTER-6-USB_PRINTER_INSERTED

6-Information

USB Printer inserted: [chars].

A USB Printer has been detected.

print-server

"Informational message only. No action required."

USB_PRINTER-6-USB_PRINTER_REMOVED

6-Information

USB Printer removed: [chars].

A USB Printer has been removed.

print-server

"Informational message only. No action required."

USB_PRINTER-3-USB_PRINTER_OBJECT_FAIL

3-Error

Could not create printer object for [chars].

Could not create the printer object.

print-server

"Remove this printer and insert it again."

USB_PRINTER-3-FAIL_TO_CREATE_WATCHED_BOOLEAN

3-Error

Could not create a watched boolean for [chars].

USB Printer could not create a watched boolean. This condition indicates that memory resources are being exhausted.

print-server

"Please check memory usage " " and report it to TAC."

USB_PRINTER-3-FAIL_TO_CREATE_SCHEDULER

3-Error

Could not create a job scheduler for [chars].

USB Printer could not create a scheduler process. This condition indicates that memory resources are being exhausted.

print-server

"Please check memory usage " " and report it to TAC."

USB_PRINTER-3-FAIL_TO_GET_APP_HANDLE

3-Error

Could not get application handle for printer [chars].

Could not get application handle from the USB stack.

print-server

"Remove this printer and insert it again."

USB_PRINTER-3-NO_PAPER

3-Error

Could not create job since there is no paper in printer [chars].

Could not create job because of lack of paper.

print-server

"Please put paper in the tray and re-submit job."

USB_PRINTER-3-PRINTER_IN_ERROR

3-Error

Could not create job since printer [chars] is in error.

Could not create job because port status command returned error.

print-server

"Try rebooting printer once. If problem still persists report to TAC."

USB_TOKEN_FILESYS-6-USB_TOKEN_INSERTED

6-Information

USB Token device inserted: [chars].

A USB Token device has been detected.

usb-token-filesys

"Informational message only. No action required."

USB_TOKEN_FILESYS-6-USB_TOKEN_REMOVED

6-Information

USB Token device removed: [chars].

A USB Token device has been removed.

usb-token-filesys

"Informational message only. No action required."

USB_TOKEN_FILESYS-6-REGISTERING_WITH_IFS

6-Information

Registering USB Token File System [chars]: might take a while...

Registering USB Token File System is being registered.

usb-token-filesys

"Informational message only. No action required."

USB_TOKEN_FILESYS-3-FAIL_TO_BUILD_MFD

3-Error

USB Token File System failed to build MFD...

USB Token File System failed to build the Master File Directory MFD database.

usb-token-filesys

"Remove this token and insert it again. " "If the problem still persists report the error message to your " "technical representative along with the output of 'show usb' " "'show usb controller' and 'show file system' commands."

USB_TOKEN_FILESYS-3-MFD_FORWARD_INCOMPATIBLE

3-Error

Unable to understand MFD database of version [dec].[dec].

The version of the Master File Directory MFD database stored

usb-token-filesys

"Upgrade the USB Token File System by reloading " "the router with a higher version of IOS software."

USB_TOKEN_FILESYS-6-REGISTERED_WITH_IFS

6-Information

USB Token File System [chars] is registered...

USB Token File System registered successfully.

usb-token-filesys

"Informational message only. No action required."

USB_TOKEN_FILESYS-3-FAIL_TO_REGISTER_WITH_IFS

3-Error

Failed to register USB Token File System with IFS.

The process of registering USB Token File System with IOS File System IFS did not succeed.

usb-token-filesys

"Remove this token and insert it again. " "If the problem still persists report the error message to your " "technical representative along with the output of 'show usb' " "'show usb controller' and 'show file system' commands."

USB_TOKEN_FILESYS-3-MAX_TOKENS_INSERTED

3-Error

The number of tokens exceeded the maximum that can be supported by USB Token File System.

Maximum number of tokens that can be supported by USB Token File System are already inserted.

usb-token-filesys

"Remove the other tokens that are not in use. " "And remove and insert this token again. " "If the problem still persists report the problem to your " "technical representative along with the output of 'show usb' " "'show usb controller' and 'show file system' commands."

USB_TOKEN_FILESYS-3-FAIL_TO_CREATE_TALKER

3-Error

Token File System callback: failed to create token talker token name [chars] status [dec].

USB Token File System failed to establish connection with USB Token Device Driver.

usb-token-filesys

"Remove and insert this token again. " "If the problem still persists report the error message to your " "technical representative along with the output of 'show usb' " "'show usb controller' and 'show file system' commands."

USB_TOKEN_FILESYS-3-FAIL_TO_DESTROY_TALKER

3-Error

Token File System callback: failed to destroy token talker token name [chars] status [dec].

USB Token File System failed to destroy the connection with USB Token Device Driver.

usb-token-filesys

"Insert and remove this token again. " "If the problem still persists report the error message to your " "technical representative along with the output of 'show usb' " "'show usb controller' and 'show file system' commands."

USB_TOKEN_FILESYS-3-UNKNOWN_TOKEN_EVENT

3-Error

Token File System callback: unknown event [dec].

USB Token File System callback function received an unknown event from USB Token Device Driver.

usb-token-filesys

"Check USB ports to see if the token device is inserted or removed " "correctly. If the problem still persists report the error message " "to your technical representative along with the output of 'show usb' " "'show usb controller' and 'show file system' commands."

USB_TOKEN_FILESYS-3-FAIL_TO_CREATE_WATCHED_BOOLEAN

3-Error

Could not create a watched boolean!

USB Token File System could not create a watched boolean. This condition indicates that memory resources are being exhausted.

usb-token-filesys

"Reduce other system activities to ease memory demands or remove " "any token device that is not in use to free up some memory."

USB_TOKEN_FILESYS-3-ASYNC_IO_UNEXPECTED_EVENT

3-Error

Token Asynchronous I/O: Unexpected Event [dec].

Token Asynchronous I/O process received an unexpected event.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

USB_TOKEN_FILESYS-3-ASYNC_IO_FAIL_TO_REQUEUE_REQUEST

3-Error

Token Asynchronous I/O: failing to requeue an I/O request.

Token Asynchronous I/O process failed to requeue an I/O request.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

USB_TOKEN_FILESYS-3-ASYNC_IO_FAIL_TO_GET_ARGUMENT

3-Error

Token Asynchronous I/O: Could not get argument.

Token Asynchronous I/O process failed to retrieve argument.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

USB_TOKEN_FILESYS-3-ASYNC_IO_ERROR_WRITING_FILE

3-Error

Error writing file: file [chars] ret code [hec] [chars].

Token Asynchronous I/O process encountered I/O write failure.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

USB_TOKEN_FILESYS-3-ASYNC_IO_ERROR_CREATING_FILE

3-Error

Error creating file: file [chars] ret code [hec] [chars].

Token Asynchronous I/O process failed to create a file in USB token device.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

USB_TOKEN_FILESYS-3-ASYNC_IO_ERROR_CREATING_DIRECTORY

3-Error

Error creating directory: dir [chars] ret code [hec] [chars].

Token Asynchronous I/O process failed to create a directory in USB token device.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

USB_TOKEN_FILESYS-3-ASYNC_IO_ERROR_DECODE_OP_CODE

3-Error

Unrecognized I/O Op-code: [dec].

Token Asynchronous I/O process could not decode the Op-code in an I/O request.

usb-token-filesys

"Report the error message to your technical representative " "along with the output of 'show usb' 'show usb controller' and " "'show file system' commands."

TLV-3-GET

3-Error

Reading data type [dec]

An expected field in the TLV buffer was either missing or malformed

-

LOG_STD_RECUR_ACTION

TLV-3-UPDATE

3-Error

Unable to write type [dec]

An attempt to update a TLV entry failed.

-

LOG_STD_RECUR_ACTION

MEM_MGR-3-MEM_MGR_NOMEM

3-Error

Out of memory

System out of memory.

-

LOG_STD_ACTION

MEM_MGR-3-MEM_MGR_EXCEED_MAX

3-Error

memory pool exceeds maximum [dec] bytes allowed.

An attempt was made to allocate a buffer\n\ from the specified memory pool which has\n\ reached its maximum limit

-

LOG_STD_ACTION

MEM_MGR-3-MEM_MGR_INVALID

3-Error

The Memory Management code encounters an invalid parameter.

It appears that the Memory Management code has\n\ received an invalid parameter from its caller.

-

"Copy the error message exactly has it appears\n\ and report it to your technical support\n\ representative."

CLUE-3-INTERNAL_SW_ERROR

3-Error

[chars]

Internal Compact Local Unit Exchange CLUE software error reported

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

CLUE-3-INIT_ERROR

3-Error

Failed to initialise the reserved memory for new CLUE context due to [chars]

-

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

CLUE-3-NOT_ENOUGH_MEMORY

3-Error

[dec]-bytes of local memory has not enough space left to reserve [dec]-bytes of CLUE storage

Local memory was not big enough to reserve the required Compact Local \n\ Unit Exchange CLUE storage space.

clue

"Add more local memory."

CLUE-3-NOT_ENOUGH_CLUE_STORAGE

3-Error

CLUE storage has not enough space to allocate record id [dec] and data size [dec]

-

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

CLUE-3-INVALID_REC_ID

3-Error

Invalid CLUE record id [dec] has been received so CLUE cannot [chars] it

-

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

CLUE-3-INVALID_REC_DATA_SIZE

3-Error

CLUE record size [dec] is invalid to allocate CLUE record [dec]

-

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

CLUE-3-NO_SIGNATURE

3-Error

CLUE cannot [chars] record id [dec]

The given CLUE record was not serviced. CLUE storage was not \n\ available or the CLUE storage signature was invalid.

clue

"Internal CLUE software may automatically rectify the error. However \n\ if the error persists copy the error message exactly as it appears and \n\ report it to your technical support representative."

CLUE-3-COMMIT_FAILED

3-Error

CLUE cannot commit record id [dec]

The given CLUE record was not committed in the CLUE storage memory.\n\ CLUE record was not allocated by the CLUE client before committing or \n\ there was an error in the internal CLUE record index table. The CLUE \n\ record cannot be accessed.

clue

"Internal CLUE software may automatically rectify the error. However \n\ if the error persists copy the error message exactly as it appears and \n\ report it to your technical support representative."

CLUE-3-CLIENT_REGISTRY_FULL

3-Error

Maximum of [dec] CLUE clients registered. Cannot register callback [hex]

-

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

CLUE-3-CHECKSUM_ERROR

3-Error

CLUE record checksum error in record id [dec] record starting address [hex] new checksum [hex] previous checksum [hex]

CLUE record stored in the CLUE memory had a bad checksum. The \n\ CLUE record was modified by a CLUE client but not committed or by \n\ unknown memory corruption. The CLUE record cannot be accessed.

clue

"Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit."

CLUE-3-SOR_CORRUPT

3-Error

CLUE record corruption in start of record field record id [dec] record starting address [hex]

CLUE record's start of record delimiter was corrupted in the CLUE \n\ storage memory. The CLUE record was over-written by the\n\ previous CLUE record or by an unknown memory corruption. The \n\ CLUE record cannot be accessed.

clue

"Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit."

CLUE-3-EOR_CORRUPT

3-Error

CLUE record corruption in end of record field record id [dec] record starting address [hex]

CLUE record's end of record delimiter was corrupted in the CLUE \n\ storage memory. The CLUE record was over-written by the\n\ previous CLUE record or by an unknown memory corruption. The \n\ CLUE record cannot be accessed.

clue

"Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit."

CLUE-3-INDEX_BUILD_FAIL

3-Error

Failed to build CLUE internal record index due to [chars]

CLUE expected existence of valid CLUE records in CLUE storage when \n\ building internal record index table. CLUE will fail to build the index\n\ table when CLUE storage does not exist or any CLUE record within the\n\ CLUE storage has some data corruption. CLUE service will not be \n\ available and any data in the CLUE storage cannot be accessed.

clue

"Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit."

CLUE-3-INVALID_AREA

3-Error

Either address [hex] or size [dec] reserved for CLUE storage area is invalid

-

clue

"Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative."

SRW-7-SRW_ERROR

7-Debug

[chars]: [hec] [hec] [dec] [dec] [dec] [dec] [hec]

An internal software error occurred.

ribinfra

LOG_STD_RECUR_ACTION

SRW-7-SRW_ERROR2

7-Debug

[chars]: [hec] [hec] [dec] [dec] [dec] [dec] [hec] [hec] [hec] [hec] [dec]

An internal software error occurred.

ribinfra

LOG_STD_RECUR_ACTION

SRW-7-SRW_ERROR3

7-Debug

[chars]: [hec] [hec] [dec] [dec] [dec] [dec] [hec] [hec] [hec] [dec] [hec] [dec]

An internal software error occurred.

ribinfra

LOG_STD_RECUR_ACTION

SRW-7-BAD_SRW_DATA

7-Debug

Bad SRW data %08x

An internal software error occurred.

ribinfra

LOG_STD_RECUR_ACTION

SRW-7-BAD_SRW_MAGIC

7-Debug

Bad SRW magic %08x @ %08x

An internal software error occurred.

ribinfra

LOG_STD_RECUR_ACTION

KEYMAN-4-KEYSTR_CRYPTO_TYPE

4-Warning

Type [dec] encryption unknown. Interpreting keystring as literal

The format type was not recognized by the system. A keystring format type value of 0 unencrypted keystring or 7 hidden keystring

-

"Use the correct format for the value type or remove the space following " "the value type"

KEYMAN-4-KEYSTR_BAD_CRYPTO

4-Warning

Bad encrypted keystring for key id [dec].

The system could not successfully decrypt an encrypted keystring. The keystring may have been corrupted during system configuration.

-

"Re-enter the key-string command and reconfigure the key string."

DLINK-3-BAD_QELEM

3-Error

Bad queue elem - %08x: flink %08x blink %08x flink->blink %08x blink->flink %08x

An internal software error occurred.

DLINK_UTIL_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

DLINK-3-NULL_QELEM

3-Error

Null queue elem

An internal software error occurred.

DLINK_UTIL_DDTS_COMPONENT

LOG_STD_RECUR_ACTION

AGGMGR-0-NO_SPACE

0-Emergency

No space left for creator \[chars]\ to add data item to agg list items [dec] max [dec] remaining [dec]

An attempt was made to add an item to an aggregation list that had just been successfully created but for some reason the add failed. This situation should never occur. If it does occur then it is the result of a program error which would be found during development and considered an internal error. There is no work around.

cosmos

LOG_STD_ACTION

VINES-2-CORRUPTENTRY

2-Critical

Detected a corrupted entry in the [chars] table

The VINES code detected that an internal table entry was corrupted.

vines

"Copy the message exactly as it appears and report it your technical\n\ support representative. If possible clear the VINES\n\ routing table or neighbor table depending on the table in which the\n\ corrupted entry was observed. This will result in a temporary\n\ loss of connectivity until the routing or neighbor table is rebuilt."

VINES-2-INVALIDPATH

2-Critical

Bad [chars] in path for neighbor entry %z

While searching the neighbor table the code determined that a pointer\n\ that should point to a VINES path structure actually points to some\n\ other structure.

vines

"Copy the message exactly as it appears and report it your technical\n\ support representative. If possible clear the VINES\n\ neighbor table. This will result in a temporary loss of connectivity\n\ until all neighbors and routes are relearned."

VINES-2-INVALIDROUTE

2-Critical

Bad [chars] in route for server entry %Z

While searching the routing table the code determined that a pointer\n\ that should point to a VINES route structure actually points to some\n\ other structure.

vines

"Copy the message exactly as it appears and report it your technical\n\ support representative. If possible clear the VINES\n\ routing table. This will result in a temporary loss of connectivity\n\ until all routes are relearned."

VINES-2-CONSISTENCY

2-Critical

Error [chars]

The VINES code ran into a situation that should not happen. For\n\ example an IPC port number needs to be allocated but all 65535 port\n\ numbers are currently in use. Another possible cause is that VINES \n\ attempted to add a cache entry but had no path associated with the \n\ destination address. This may cause temporary slow performance to \n\ only those stations that have experienced this inconsistency \n\ until complete cache entries are added. However connectivity\n\ should not be lost because all data traffic can still be routed \n\ vvia process-level switching.

vines

"Copy the message exactly as it appears and report it your technical\n\ support representative. If the warning message is about IPC port \n\ number depletion use the show vines ipc command to check how many \n\ IPC ports are currently in use by which services and determine\n\ whether the IPC connections are all legitimate. To release IPC ports \n\ issue the clear vines ipc command. If the warning message is about\n\ vines cache entries provide the contents of the vines route cache\n\ neighbor and route tables immediately after the error messages \n\ appeared. If the problem persists issue the clear vines\n\ cache command and monitor the router if the situation improves."

VINES-2-NOBUFFERS

2-Critical

No buffers available for [chars]

There were no buffers available to send a VINES service query\n\ or reply.

vines

"Examine your system's memory and buffer capacity and compare\n\ it with current usage. If you notice a substantial discrepancy\n\ monitor your system for possible memory leaks or buffer drainage\n\ and report the problem to your technical support representative\n\ along with the output of the show memory show memory processor\n\ show buffers show buffers assigned and show buffers old commands."

VINES-2-ENCAPFAILED

2-Critical

Encapsulation failed for [v-name] via [v-name] on [chars]

VINES fast switching encountered an encapsulation failure\n\ when building a cache entry for a neighbor.

vines

"Examine your configuration for causes of the encapsulation failure.\n\ Look for missing map statements interfaces that have gone down and so\n\ on. If this error results in lost connectivity disable vines fast\n\ switching by issuing the no vines route-cache command. Because\n\ disabling fast switching will slow network perform you should\n\ issue the vines route-cache command to re-enable fast switching\n\ as soon as you have identified the cause of the problem. If you\n\ cannot identify the cause contact your technical support\n\ representative. Provide the output of the show vines cache\n\ show vines neighbor and show vines route commands for the\n\ destination address and neighboring routers you are using. Also\n\ provide the output of the show interface and show vinces\n\ interface commands for the incoming and outgoing interfaces."

VINES-2-CACHEFAILED

2-Critical

Cannot build cache entry [dec] bytes for [v-name] on [chars]

VINES fast switching detected that the packet destined to a given\n\ address did not have proper encapsulation information or its\n\ encapsulation size was too large to fit into the cache.

vines

"Verify that the VINES encapsulation and interface-specific mappings\n\ for the interface concerned are properly configured. Copy the \n\ message exactly as it appears and report it your technical\n\ support representative."

VINES-2-CACHEUNSUPP

2-Critical

Caching of [chars] not supported on [chars]

The cache population routing for VINES fast switching was called for\n\ an interface that does not support VINES fast switching.

vines

"Copy the message exactly as it appears and report it your technical\n\ support representative. If other encapsulation types are available\n\ on the interface try using them. If this problem is not limited to \n\ one or two destinations but rather occurs with all traffic\n\ using the interface diable VINES fast switching for the\n\ interface until you have identified the real cause of the problem."

VINES-2-DUPADDR

2-Critical

Duplicate address detected on interface [chars]

The router detected that its VINES address is being used by another\n\ router.

vines

"To identify the other router that is using this address manually\n\ inspect each router's configuration. When you have identified\n\ the router with the duplicate address issue the vines routing\n\ recompute command on both routers or issue the enable vines routing \n\ command specifying specify a unique address. If one of the routers \n\ does not support the recompute keyword disable VINES on that router \n\ issue the write terminal command to save the configuration to memory \n\ reboot the router and then enter the vines routing command with\n\ a unique vines address on the offending routers until each router has\n\ a unique address."

VINES-2-BADPARAM

2-Critical

[chars] called with [chars] parameter set to [chars]

One of the VINES lookup functions was called with an illegal\n\ argument.

vines

"Copy the message exactly as it appears do a memory dump up to\n\ 128 bytes and the location specified in the error message and report \n\ this information to your technical support representative."

VINES-2-BADTIMER

2-Critical

RTP timer for [chars] was found disabled and was reset

An internal interface timer is not running. This condition usually\n\ occurs after an interface is reset.

vines

"No action is required. The system automatically restarts the timer."

VINES-6-IPCNOROUTINE

6-Information

IPC port [dec] registered without an upcall [chars]

There is an inconsistency in the active VINES data structure for\n\ handling IPC data messages. A message was received for a port that\n\ should have a listener but the listener routine cannot be found.

vines

"Examine the IPC ports currently supported on the router\n\ by issuing the show vines ipc command and see whether the reported\n\ IPC port is indeed not active. Copy the message exactly as it\n\ appears and report it to your technical support representative\n\ along with the output of the debug vines ipc command."

VINES-6-RPCNOSERVICE

6-Information

IPC port [dec] registered without a service

There is an inconsistency in the active VINES data structure for\n\ handling Net RPC messages. A message was received for a port that\n\ should have a service description but that service description cannot\n\ be found.

vines

"Enter the show vines ipc command and see whether the reported IPC\n\ port has a registered service. Copy the message exactly as it\n\ appears and report it to your technical support representative\n\ if possible along with output of the debug vines netrpc command."

VINES-6-RTNNOTFOUND

6-Information

[chars] service [chars] routine not found while [chars]

There is an inconsistency in the active VINES service description data\n\ structures. A service handler routine cannot find the description of\n\ its own service.

vines

"Copy the message exactly as it appears and report it your technical\n\ support representative. In addition provide the output of the show\n\ vines service command and debug vines service traces for the\n\ service reported in the error message."

VINES-6-FNNOTFOUND

6-Information

[chars] service [chars] routine missing [chars] vector

There is an inconsistency in the static VINES data structures for\n\ handling application-layer packets.

vines

"Turn on VINES service level debugging for the service reported\n\ in the error message and copy the debug traces and the error\n\ message exactly as they appear and report them to your technical\n\ support representative."

VINES-2-NOVENCAP

2-Critical

Encapsulation failed on [chars] for address [v-name]

The VINES code tried to send a packet on an interface that does not\n\ have a new encapsulation routine for outbound packets.

vines

"Toggle the problematic interface by issuing the interface shut and\n\ no shut commands and then issue the no vines metric and vines metric\n\ command see if the problem goes away. If the problem persists copy\n\ the message exactly as it appears and report it your technical\n\ support representative. If possible turn on and provide\n\ interface- specific debug traces particularly for VINES activities."

VLAN-5-PRIMARY_LINK_NOT_IN_EC

5-Notice

Warning: VLAN [dec]'s main interface is not the channel group of primary=[chars]\nPer-VLAN manual load-balancing will not take effect until channel-group is configured under the\n primary interface.

The interface configured as primary is not a memberlink in the port channel.

vlan

"Verify the configuration."

VLAN-5-SECONDARY_LINK_NOT_IN_EC

5-Notice

Warning: VLAN [dec]'s main interface is not the channel group of secondary=[chars]\nPer-VLAN manual load-balancing will not take effect until channel-group is configured under the\n secondary interface.

The interface configured as secondary is not a memberlink in the port channel.

vlan

"Verify the configuration."

VLAN-3-INTERFACE_NOT_PRESENT

3-Error

The [chars] link [chars] does not exist. Sub-interface: [chars] VLAN-Id: [dec]

This message appears when the below command is issued under port-channel sub-interface with the unknown

vlan

"Verify if the interface shows up using the " "command - show ip int brief. \n Please insert " "the card in case it is removed and run " "the command again once the card comes up."

VLAN-3-XDRLEN

3-Error

Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec]

-

-

-

VPDN-6-CLOSED

6-Information

[chars] [chars][chars] closed [chars] [chars] [chars][chars][chars]

The remote server typically the HGW/LNS closed this session. The reason for the closure is encoded in a hexadecimal format and corresponds to the particular protocol descriptions i.e. for L2F the values are documented in section 4.4.5 of the Internet Draft. A description string may also be present which describes the closure reason.

vpdn

"Check configuration on the NAS/LAC or HGW/LNS"

VPDN-6-DOWN

6-Information

[chars] [chars][chars] changed state to down [chars] [chars] [chars][chars][chars]

The remote server typically the HGW/LNS closed this tunnel. The\n\ reason for the closure is encoded in a decimal format which\n\ corresponds to the particular protocol descriptions i.e. for L2F\n\ the values are documented in section 4.4.5 of the Internet Draft.\n\ A description string may also be present which describes the\n\ closure reason.

vpdn

"Check configuration on the NAS/LAC or HGW/LNS"

VPDN-6-AUTHENERR

6-Information

[chars] [chars][chars] cannot authenticate for [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS is unable to locate a AAA server for the purposes of authenticating the user or tunnel. An error of this type indicates that the router was unable to establish a network connection with the designated/configured server. A reason string may also be present to provide further information.

vpdn

"Check AAA configuration on the NAS/LAC or HGW/LNS and network " "connectivity to the AAA servers."

VPDN-6-AUTHENFAIL

6-Information

[chars] [chars][chars] [chars]authentication failure [chars]for [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS has failed to authenticate a user or a tunnel or the HGW/LNS has failed authentication with the client which initiated the session. For authentication failures of the user or tunnel a reason string should be present which will indicate the point of failure. When a client fails to authenticate the HGW a reason string may be present depending upon the point of failure.

vpdn

"Check username configuration on the NAS/LAC or HGW/LNS and possibly " "even the client if the HGW/LNS is failing authentication removing " "the negotiation of outbound authentication is one possible solution " "i.e. only authenticate the user in the inbound direction.\n" "If AAA is applicable check AAA configuration on the NAS/LAC or " "HGW/LNS and network connectivity to the AAA servers."

VPDN-6-AUTHORERR

6-Information

[chars] [chars][chars] cannot authorize for [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS is unable to locate a AAA server for the purposes of authorizing the user or tunnel. An error of this type indicates that the router was unable to establish a network connection with the designated/configured server. A reason string may also be present to provide further information.

vpdn

"Check AAA configuration on the NAS/LAC or HGW/LNS and network " "connectivity to the AAA servers."

VPDN-6-AUTHORFAIL

6-Information

[chars] [chars][chars] [chars]authorization failure for [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS has failed to authorize a user or a tunnel. A reason string may be present to indicate the point of failure.

vpdn

"Check authorization configuration on the NAS/LAC or HGW/LNS. If AAA " "is applicable check network connectivity to the AAA servers."

VPDN-5-UNREACH

5-Notice

[chars] [chars][chars] is unreachable

The NAS/LAC or HGW/LNS has timed out attempting to establish a tunnel connection to a HGW/LNS or NAS/LAC. This may be due to network or authentication/authorization issues.

vpdn

"Check configuration on the NAS/LAC or HGW/LNS check network " "connectivity between the NAS/LAC and HGW/LNS. Check if the tunnel " "setup needs to have a different source IP address from that of " "the NAS/LAC."

VPDN-5-NOIDB

5-Notice

[chars] [chars][chars] unable to terminate user [chars]

The HGW/LNS is out of resources to create sessions for VPDN forwarded users in particular it has reached the maximum number of interfaces allowed on the router.

vpdn

""

VPDN-4-SESSIONERROR

4-Warning

[chars] [chars][chars] unable to terminate user [chars][chars][chars]

The HGW/LNS was unable to complete the forwarding of the VPDN user due to an internal error. This error may be resource related or configuration related. A reason string may be present to indicate the point of failure.

vpdn

"Check the configuration on the HGW/LNS"

VPDN-3-NORESOURCE

3-Error

[chars] [chars][chars] no resources for user [chars][chars][chars]

The NAS/LAC or HGW/LNS is out of resources for the forwarding of a VPDN user.

vpdn

""

VPDN-6-TIMEOUT

6-Information

[chars] [chars][chars] disconnected [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS has disconnected the user due to the expiration of a timer this may be e.g. PPP negotiation related or an absolute timeout for the session.

vpdn

""

VPDN-6-SOFTSHUT

6-Information

[chars] [chars][chars] has turned on softshut and rejected [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS can no longer accept new connection when\n\ softshut has been turned on. Existing session will continue until\n\ termination.

vpdn

""

VPDN-4-REFUSED

4-Warning

Session for [chars] Refused status = [hec]

The remote server refused this session.

-

"Check configuration on the HG or LNS"

VPDN-6-RESIZE

6-Information

Updated [chars] MID table size to [dec]

The NAS/LAC or HGW/LNS has altered the size of the session table through command line configuration.

-

""

VPDN-6-MAX_SESS_EXCD

6-Information

[chars] [chars][chars] has exceeded configured local session-limit and rejected [chars] [chars] [chars][chars][chars]

The NAS/LAC or HGW/LNS has refused this session since the configured\n\ maximum VPDN session limit has been reached.

vpdn

""

VPDN-3-IP_SWITCH_ERR

3-Error

l2x ip switching vector not installed

Platform dependent l2x ip cef switching module is missing.

vpdn

""

VPDN-3-DROP_ADDR_MISMATCH

3-Error

[chars]

The remote server changed its address.

vpdn

"Change initiate-to configuration at the LAC to point to the exact IP " "address LNS will use"

VPDN-6-VPDN_DEADCACHE_EVENT

6-Information

LSG dead cache entry [inet] [chars]

A dead cache entry status is changed in the VPDN Load Sharing Group LSG table. The event could be 'Added' where a LSG entry

vpdn

""

VPDN-6-TUNNEL_IN_RESYNC

6-Information

[chars] [chars] [chars] tunnel is in HA resync reject [chars] [chars] [chars]

The tunnel towards the peer is still in High Availability HA

vpdn

"It is normal for this to occur during tunnel High Availability HA "

VPDN-6-QUEUED_PACKET_INFO

6-Information

UnsetQ reached msg alert threshold. local_cc_id=[dec] unsentQ=[dec] resendQ=[dec] max_unsentQ=[dec] max_resendQ=[dec]

UsentQ size has reached the message alert threshold. Message alert threshold can be configured through CLI 'vpdn queuesize-alert <num>'.

vpdn

""

L2TUN-3-ILLEGAL

3-Error

[chars]

An illegal event has been processed by the L2TUN subsystem.

L2TUN

LOG_STD_NO_ACTION

L2TP-3-ILLEGAL

3-Error

[chars]: [chars]

An illegal event has been processed by the L2TP subsystem.

L2TP

LOG_STD_NO_ACTION

L2TP-3-CRITICAL

3-Error

[chars]

An critical event has been processed by the L2TP subsystem.

L2TP

LOG_STD_NO_ACTION

L2TP-5-IGNOREICMPMTU

5-Notice

Ignoring received ICMP Type 3 Code 4 due to pmtu min or max setting

An ICMP Type 3 Code 4 fragmentation needed and DF set packet

L2TP

"If you want the ICMP packet to be accepted and used to " "decrease or increase the MTU then use the " "<CmdBold>vpdn pmtu min <NoCmdBold> command to " "decrease the minimum MTU allowed and enter the " "<CmdBold> vpdn pmtu max <NoCmdBold> command to " "increase the maximum MTU that is allowed. The minimum value " "specified is the minimum MTU that is allowed and the " "maximum value specified is the maximum MTU that is " "allowed."

L2TP_HA -3-SYNC

3-Error

[chars]: code [dec]

An error occurred when syncing L2TP state to the Standby Route Processor. This may affect Non-Stop Forwarding capability on L2TP-based interfaces during and after switchover until the state is recovered through normal protocol operation.

fr

"Reset the standby processor to attempt the sync again. " LOG_STD_RECUR_ACTION

L2TP_HA -3-ISSU

3-Error

[chars]: [chars]

A L2TP ISSU error occurred.

l2tp

LOG_STD_SH_TECH_ACTION

VQPCLIENT-7-RECONF

7-Debug

Reconfirming VMPS responses

The switch is reconfirming all responses with the VMPS

dynamic_vlan

LOG_STD_DBG_ACTION

VQPCLIENT-4-IPADDR

4-Warning

Main IP address on [chars] was deleted

-

dynamic_vlan

-

VQPCLIENT-2-IPSOCK

2-Critical

Could not obtain IP socket

An error occurred when the system attempted to open an IP socket to the VMPS.

dynamic_vlan

LOG_STD_RECUR_ACTION

VQPCLIENT-2-DENY

2-Critical

Host [enet] denied on interface [chars]

The VMPS has denied access for the given host MAC address to the specified interface.

dynamic_vlan

"No action is normally required. If you feel that " "the host should have been allowed access then the " "configuration on the VMPS should be checked."

VQPCLIENT-2-SHUTDOWN

2-Critical

Interface [chars] shutdown by VMPS

The VMPS has directed that the specified interface be shut down.

dynamic_vlan

"No action is normally required. If you feel that " "the port should not have been shut down then the " "configuration on the VMPS should be checked."

VQPCLIENT-3-VLANNAME

3-Error

Invalid VLAN [chars] in response

The VMPS has specified a vlan name that is unknown to the switch.

dynamic_vlan

"Make sure that the vlan exists on the switch. " "Check the VMPS configuration."

VQPCLIENT-3-IFNAME

3-Error

Invalid interface [chars] in response

The VMPS has sent an unsolicited response with an unknown interface name

dynamic_vlan

"Check the VMPS configuration."

VQPCLIENT-3-THROTTLE

3-Error

Throttling VLAN change on [chars]

An attempt was made to change the vlan assignment for the specified interface more often than once every 10 seconds. The vlan change is denied.

dynamic_vlan

"No action is normally required. If the message " "recurs check the VMPS configuration. Verify " "that unexpected hosts are not connected to " "the port."

VQPCLIENT-2-TOOMANY

2-Critical

Interface [chars] shutdown by active host limit

The system has shut down the specified interface because too many hosts have requested access to that port.

dynamic_vlan

"To reactivate the port remove the excess hosts " "and issue a no shut command to the interface."

VQPCLIENT-7-PROBE

7-Debug

Probing primary server %I

The system is trying to reestablish connectivity with the primary VMPS at the given IP address.

dynamic_vlan

LOG_STD_DBG_ACTION

VQPCLIENT-7-NEXTSERV

7-Debug

Trying next VMPS %I

The system has lost connectivity with the current VMPS and is switching to the next server in its list.

dynamic_vlan

LOG_STD_DBG_ACTION

VQPCLIENT-2-CHUNKFAIL

2-Critical

Could not allocate memory for VQP

An error occurred when the system tried to allocate memory for the VQP client.

dynamic_vlan

LOG_STD_ACTION

VQPCLIENT-2-INITFAIL

2-Critical

Platform-specific VQP initialization failed. Quitting

An error occurred during initialization of the VQPC platform-specific code.

dynamic_vlan

LOG_STD_ACTION

VQPCLIENT-2-PROCFAIL

2-Critical

Could not create process for VQP. Quitting

An error occurred while creating a process for the VQP client.

dynamic_vlan

LOG_STD_ACTION

VQPCLIENT-7-DELETING

7-Debug

Freeing deleted saved responses

-

dynamic_vlan

-

VQPCLIENT-7-STARTUP

7-Debug

Starting VQP client

-

dynamic_vlan

-

VQPCLIENT-7-STOPPING

7-Debug

Stopping VQP client

-

dynamic_vlan

-

VRRP-6-STATECHANGE

6-Information

[chars] Grp [dec] state [chars] -> [chars]

The VRRP router has changed state

vrrp

LOG_STD_NO_ACTION

VRRP-4-BADAUTHTYPE

4-Warning

Bad authentication from [inet] group [dec] type [dec] expected [dec]

Two routers participating in VRRP disagree on the valid authentication type.

vrrp

"Use the vrrp authentication command to repair the VRRP authentication\n\ discrepancy between the local system and the one whose IP address\n\ is reported."

VRRP-4-BADAUTH

4-Warning

Bad authentication from [inet] group [dec] type [dec]

Two routers participating in VRRP disagree on authentication

vrrp

"Use the vrrp authentication command to repair the VRRP authentication\n\ discrepancy between the local system and the one whose IP address\n\ is reported."

VRRS-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting-off records may not be sent.

Failed to create the accounting process.

fhrp

"Free up some memory."

FR_HA -3-SYNC

3-Error

[chars]: code [dec]

An error occurred when syncing Frame Relay state to the Standby Route Processor. This may affect Non-Stop Forwarding capability on Frame Relay interfaces during and after switchover until the state is recovered through normal protocol operation.

fr

"Reset the standby processor to attempt the sync again. " LOG_STD_RECUR_ACTION

FR_HA -3-ISSU

3-Error

[chars]: [chars]

A Frame Relay ISSU error occurred.

fr

LOG_STD_SH_TECH_ACTION

DAPR_BR-5-STATUS

5-Notice

[chars]

Border-Router status

dapr

LOG_STD_NO_ACTION

DAPR_BR-5-RESET

5-Notice

reason: [chars]

Border-Router reset due to mentioned reason

dapr

LOG_STD_NO_ACTION

DAPR_BR-5-RM_ROUTE_INVALID

5-Notice

No route or route is via egress

Invalid route from Border-Router to Route-Manager

dapr

LOG_STD_ACTION

DAPR_BR-5-NBR_ROUTE_INVALID

5-Notice

Neighbor-BR [inet]

Invalid route to neighbor Border-Router

dapr

LOG_STD_NO_ACTION

DAPR_BR-5-NBR_TUNNEL_UPDOWN

5-Notice

Neighbor-BR [inet] tunnel [chars]

Status of tunnel to neighbor Border-Router

dapr

LOG_STD_ACTION

DAPR_BR-5-EGRESS_INTF_THRESHOLD_EXCEED

5-Notice

[chars] curr-util %llu%% max-util %ld%%

DAPR egress interface utilization threshold exceeded

dapr

LOG_STD_NO_ACTION

DAPR_BR-5-EGRESS_INTF_NOT_VIABLE

5-Notice

[chars] curr-bwkbps %lu min-bwkbps %ld

DAPR egress interface not viable

dapr

LOG_STD_NO_ACTION

DAPR_BR-5-EGRESS_INTF_UPDOWN

5-Notice

[chars] [chars]

DAPR egress interface status

dapr

LOG_STD_NO_ACTION

DAPR_BR-5-INGRESS_INTF_UPDOWN

5-Notice

[chars] [chars]

DAPR ingress interface status

dapr

LOG_STD_NO_ACTION

DAPR_BR-4-PREFIX_LIMIT_EXCEEDED

4-Warning

curr [dec] max [dec]

DAPR RIB prefixes exceeded

dapr

LOG_STD_NO_ACTION

DAPR_BR-4-FLOW_LIMIT_EXCEEDED

4-Warning

curr [dec] max [dec]

DAPR Flows exceeded

dapr

LOG_STD_NO_ACTION

DAPR_BR-4-RMAP_LIMIT_EXCEEDED

4-Warning

curr [dec] max [dec]

DAPR route-map entries exceeded max allowed

dapr

LOG_STD_NO_ACTION

DAPR-4-INTERNAL_ERROR

4-Warning

[chars]

Internal error

dapr

LOG_STD_ACTION

DAPR_RM-6-APP_RT_INSTALL

6-Information

[chars] BW:[dec] [chars]

App route installed for flow-group

dapr

LOG_STD_NO_ACTION

DAPR_RM-6-APP_RT_DEL

6-Information

[chars] BW:[dec]

App route deleted for flow-group

dapr

LOG_STD_NO_ACTION

DAPR_RM-4-NO_VIABLE_PATH

4-Warning

[chars]

No viable path found for flow-group

dapr

LOG_STD_NO_ACTION

DAPR_RM-3-APP_RT_COMPUTE_FAILED

3-Error

[chars]

App route compute failed for flow-group

dapr

LOG_STD_NO_ACTION

DAPR_RM-4-APP_REROUTE_FAILED

4-Warning

[chars]

App route re-compute failed for flow-group

dapr

LOG_STD_NO_ACTION

DAPR_RM-5-BR_STATUS

5-Notice

BR [chars] [chars]

Border-Router status on RM

dapr

LOG_STD_NO_ACTION

DAPR_RM-3-BR_RESET

3-Error

BR [chars] reason: [chars]

RM reset the BR due to mentioned reason

dapr

LOG_STD_ACTION

DAPR_RM-6-BR_EVENT

6-Information

BR [chars] event: [chars]

RM received event from BR

dapr

LOG_STD_ACTION

DAPR_RM-4-RIB_MISMATCH

4-Warning

route-count: old [dec] new [dec]

Mismatch of RIB database between BRs and RM

dapr

LOG_STD_ACTION

DAPR_RM-3-BR_REG_FAILED

3-Error

BR [chars] reason: [chars]

BR Registration failed

dapr

LOG_STD_ACTION

DAPR_RM-6-RM_RESET

6-Information

reason: [chars]

RM reset due to the mentioned reason

dapr

LOG_STD_ACTION

DAPR_RM-5-RM_STATUS

5-Notice

[chars]

Route-Manager status

dapr

LOG_STD_NO_ACTION

DAPR_RM-4-FLOW_EXP_PKT_INVALID_SEQ

4-Warning

BR [chars] last-seq [dec] curr-seq [dec]

Unexpected seq num in flow export pkt

dapr

LOG_STD_ACTION

DAPR_RM-3-FLOW_EXP_PKTS_MISSED

3-Error

BR [chars] missed-pkts [dec]

Flow export packets missed

dapr

LOG_STD_ACTION

DAPR_RM-4-FLOW_DATA_RECS_IGNORED

4-Warning

BR [chars] reason: [chars]

Flow data records ignored

dapr

LOG_STD_ACTION

DAPR_RM-3-FLOW_INVALID_EGRESS

3-Error

flow-group [chars]/[chars]/[dec] state [chars] uptime [dec]s last-transition [dec]s ingress-BR [chars] expected-egress [chars]/[dec] reported-egress [chars]/[dec]

Flow discovered from unexpected egress

dapr

LOG_STD_ACTION

DAPR_RM-4-FLOW_INVALID_INGRESS

4-Warning

flow-group [chars]/[chars]/[dec] state [chars] uptime [dec]s last-transition [dec]s ingress-BR [chars] egress-BR/intf [chars]/[dec] ingress-intf [chars]

Flow discovered from unexpected ingress

dapr

LOG_STD_ACTION

DAPR_RM-4-FLOW_MULTI_EGRESS

4-Warning

flow-group [chars]/[chars]/[dec] state [chars] uptime [dec]s num-egress [dec] prev-egress [chars]/[dec] curr-egress [chars]/[dec]

New flow discovered from multiple egresses

dapr

LOG_STD_ACTION

FR_ELMI-3-INCORRECT_ID

3-Error

Incorrect ID

Incorrect ID in QOS parameter message.

-

""

FR_ELMI-3-INCORRECT_IE

3-Error

Incorrect IE

Enhanced LMI is not configured on the interface. The frame was dropped.

-

""

FR_RP_STATS-3-INVALID_STAT_UNIT

3-Error

Error processing FR IPC stats msg: DLCI is out of bounds

An error occurred while processing a FR IPC stats message.\n\ Some of the FR PVC counters may be inaccurate.

fr

"This could be a temporary failure that may or may not affect the\n\ accuracy of PVC stats. If this error message continues to be seen\n\ multiple times please inform Cisco technical support representative."

FR_RP_STATS-3-CORRUPT_MSG

3-Error

FR IPC stats msg is corrupted: buffer [hec]: length [dec]

An error occurred while processing a FR IPC stats message. \n\ Some of the FR PVC counters may be inaccurate.

fr

"This could be a temporary failure.\n\ But there could be a possibility that some of the FR PVC counters may\n\ not have updated correctly.\n\ If the error message is seen multiple times please inform Cisco \n\ technical support representative."

FR_RP_STATS-3-INVALID_UNIT_COUNT

3-Error

FR IPC stats msg is corrupted: unit count [dec]

An error occurred while processing a FR IPC stats message.\n\ Some of the FR PVC counters may be inaccurate.

fr

"This could be a temporary failure.\n\ But there could be a possibility that some of the FR PVC counters may\n\ not have updated correctly.\n\ If the error message is seen multiple times please inform Cisco \n\ technical support representative."

FR_RP_XDR-3-CLIENT_INIT_ERROR

3-Error

FR XDR client initialization error: error code [dec]

An error occurred while registering the FR RP XDR client. \n\ Distributed packet forwarding over FR will not work.

fr

"This is a serious error. Without the FR XDR client distributed \n\ packet forwarding over FR will not work. Please inform a Cisco \n\ technical support representative"

FR_RP_XDR-3-INTERFACE_SETUP_ERROR

3-Error

Unable to setup FR XDR for interface [chars]

An error occurred while setting up FR XDR for a FR interface.\n\ This will affect distributed packet forwarding over this interface.

fr

"This is a serious error. Without FR XDR support distributed \n\ packet forwarding over the FR interface in question will not work. \n\ Please inform a Cisco technical support representative"

DIALER-2-NOSWIDB

2-Critical

No software interface associated with hw interface [chars]

An internal software error occurred.

-

"Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ show version command to obtain the software version."

DIALER-2-CIRCUITCOUNT

2-Critical

Dialer count 0 on [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

DIALER-2-NULLPTR

2-Critical

Unexpected null pointer in [chars]

An internal software error occurred.

-

LOG_STD_SH_TECH_ACTION

DIALER-6-BIND

6-Information

Interface [chars] bound to profile [chars]

This is a status message indicating that a dialer interface has\n\ been bound to a dialer profile.

-

LOG_STD_NO_ACTION

DIALER-6-UNBIND

6-Information

Interface [chars] unbound from profile [chars]

This is a status message indicating that a dialer interface has\n\ been unbound to a dialer profile.

-

LOG_STD_NO_ACTION

DIALER-4-MTU_WARNING

4-Warning

Current MTU setting of [dec] on [chars] is being overwritten by setting of [dec] defined by [chars].

This is a warning message indicating that an interface setting is changed based on a dialer rotary group memebership.

-

LOG_STD_NO_ACTION

DIALER-3-SBINIT

3-Error

Error initializing [chars] subblock data structure. [chars]

Initialization of the specified subblock data structure could not be accomplished.

-

LOG_STD_ACTION

ACR-3- ACRIFADD

3-Error

[chars] interface add failed for ACR group [dec].

Addition of interface to ACR group failed

ACR_DDTS_COMPONENT

"Get the output of \"show acr all \" immediately after this error." "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRIFDEL

3-Error

[chars] interface del failed for ACR group [dec].

Delete of interface from ACR group failed

ACR_DDTS_COMPONENT

"Get the output of \"show acr all \" immediately after this error." "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-6- ACRPVCADD

6-Information

PVC creation failed for VCD= [dec] on [chars] interface of ACR interface [chars].

PVC creation attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-6- ACRPVCDEL

6-Information

PVC deletion failed for VCD= [dec] on [chars] interface of ACR group [chars].

PVC deletion attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-6- ACRVPADD

6-Information

VP creation failed for VPI= [dec] on [chars] interface of ACR group [chars].

VP creation attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-6- ACRVPDEL

6-Information

PVC deletion failed for VPI= [dec] on [chars] interface of ACR group [chars].

VP deletion attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-6- ACRPVCENABLE

6-Information

PVC Enable failed for VCD= [dec] on [chars] interface of ACR interface [chars].

PVC enable attempt failed on ACR physical interface.

ACR_DDTS_COMPONENT

"If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRPVCDISABLE

3-Error

PVC Disable failed for VCD= [dec] on [chars] interface of ACR interface [chars].

PVC disable failed on ACR physical interface.

ACR_DDTS_COMPONENT

"Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRVPENABLE

3-Error

VP Enable failed for VPI= [dec] on [chars] interface of ACR interface [chars].

VP enable failed on ACR physical interface.

ACR_DDTS_COMPONENT

"Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-3- ACRVPDISABLE

3-Error

VP Disable failed for VPI= [dec] on [chars] interface of ACR interface [chars].

VP disable failed on ACR physical interface.

ACR_DDTS_COMPONENT

"Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative."

ACR-1-ISSU_NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

ACR_DDTS_COMPONENT

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

ACR-3-ISSU_SENDFAILED

3-Error

\nACR ISSU: send message failed rc = [dec]\n

The sending of a message has failed.

ACR_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

ACR-4-ISSU_INCOMPATIBLE

4-Warning

\nacr-issu-compat: returned FALSE

The compatibility checking has failed

ACR_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

ACR-4-ISSU_XFORM

4-Warning

\n[chars]: failed rc=[chars]

The transform has failed.

ACR_DDTS_COMPONENT

LOG_STD_SH_TECH_ACTION

FR_VCB-3-PROCESS_SWITCHING

3-Error

Switching error - vcb [chars] - [chars]

An error occurred while switching packets across vc-bundle

fr

"As a workaround delete the vc-bundle and employ a PVC to substitute " "for the vc-bundle"

FR_VCB-3-FIBSW_MISSING_TABLE_ENTRY

3-Error

FIB switching error - vc-bundle [chars]

An error occurred while FIB switching packets across vc-bundle

fr

"As a workaround delete the vc-bundle and employ a PVC to substitute " "for the vc-bundle"

FR_VCB-3-CONFIG

3-Error

Configuration error - vcb [chars] - [chars]

An error occurred while interpreting vc-bundle configuration

fr

"Try reconfiguring the vc-bundle"

FR_VCB-3-BUMPING

3-Error

Bumping error - vcb [chars] - [chars]

An error occurred while bumping traffic in a vc-bundle

fr

"As a workaround reconfigure the vc-bundle to avoid bumping"

FR_VCB-5-UPDOWN

5-Notice

FR VC-Bundle [chars] changed state to [chars]

The state of a frame-relay vc-bundle changed to up/down

fr

"Notification message only. No action required"

FR_VCB-3-ADJ_SRC_ERROR

3-Error

Error sourcing adjacency - vc-bundle [chars] dlci [dec]

An error occurred while setting up the adj for a member pvc

fr

"Try reconfiguring the vc-bundle"

FR_LC_XDR-3-PULL_SEND_ERROR

3-Error

Error occurred sending FR PVC stats to the RP: error code [dec]

An error occurred while updating the RP with FR PVC stats.\n\ Some of the FR PVC counters may be inaccurate.

fr

"Some FR PVC stats may be lost. This may be a temporary failure.\n\ If ths error message continues to be seen please contact Cisco TAC"

FR_LC_XDR-3-UNIT_SZ_TOO_BIG

3-Error

Error occurred sending FR PVC stats to the RP: [chars]: DLCI [dec]: unit sz [dec]

An error occurred while updating the RP with FR PVC stats.\n\ Some of the FR PVC counters may be inaccurate.

fr

"Some FR PVC stats may be lost. This may be a temporary failure.\n\ If ths error message continues to be seen please contact Cisco TAC"

SONET-4-ALARM

4-Warning

[chars]: [chars] [chars]

The specified SONET Alarm has been declared or released.

-

"Recommended action is to repair the source of the alarm."

SONET-4-APSMM

4-Warning

[chars]: APS mode mismatch - [chars]

There has been a unidirectional/bidirectional mismatch detected by the APS system

-

"It is recommended that the router configuration match the " "provisioned circuit."

SONET-3-BADAUTH

3-Error

[chars]: APS Bad authentication from [inet]

APS software has detected unauthorized message.

-

"This message could result from improper configuration " "unauthorized access or packet corruption." LOG_STD_ACTION

SONET-3-MISVER

3-Error

[chars]: APS version mismatch.\n\t WARNING: Loss of Working-Protect link can deselect both\n\t protect and working interfaces. [chars] router requires\n\t software upgrade for full protection.

APS software has detected that either the working or protect router requires software upgrade. APS operation can continue prior to the upgrade.

-

"Upgrade specified router."

SONET-6-APSREFL

6-Information

[chars]: Remote reflection of APS status now [chars]

APS software has detected a change in the reflected local APS status

-

"None - normal situation."

SONET-6-APSMANPRO

6-Information

Manual APS switchover initiated for [chars]

APS manual switchover is initialted

-

"None - normal situation."

SONET-3-APSEVENT

3-Error

[chars]: APS event type error: event [dec] undefined

APS software has malfunctioned

-

LOG_STD_ACTION

SONET-6-APSREMSWI

6-Information

[chars]: Remote APS status now [chars]

APS software has detected a change in the APS status of the remote interface

-

"None - normal situation."

SONET-3-APSNCHN

3-Error

APS Local request [dec] has no corresponding channel number

APS software has malfunctioned.

-

LOG_STD_ACTION

SONET-3-APSNOINTFC

3-Error

APS No interfaces available for IP connection

APS requires an out-of-band path for inter-router communication.

-

"Configure an out-of-band path for inter-router APS " "communication"

SONET-3-NOBUFFER

3-Error

No buffer available for sending APS message

No data buffer was available for sending APS message.

-

LOG_STD_RECUR_ACTION

SONET-3-NOSOCKET

3-Error

Unable to open socket

APS system unable to open a socket for communication purposes

-

LOG_STD_ACTION

SONET-3-APSCOMM

3-Error

[chars]: [chars]

APS errors related to failure of working-protect communication

-

LOG_STD_ACTION

SONET-3-APSCOMMEST

3-Error

[chars]: Link to [chars] channel established - PGP protocol version [dec]

APS has established connectivity between working and protect routers.

-

"None - information only."

SONET-3-APSCOMMCHANGE

3-Error

[chars]: Link to [chars] channel reverts to PGP protocol version [dec]

APS has reverted to a different version of the PGP protocol between working and protect routers.

-

"None - information only."

SONET-3-APSCOMMLOST

3-Error

[chars]: Link to [chars] channel lost

Connectivity between Working and Protect has been lost. APS operation can continue in degraded mode.

-

"Restore connectivity between working and protect routers."

SONET-3-ALARMTIMERFAIL

3-Error

[chars]

Alarm timer monitor process creation failed

-

LOG_STD_DDTS_TAC_DETAILS

SONET-3-APSSYNCSECONDARY

3-Error

[dec]/[dec]: No hwidb

New secondary RP unable to find device descriptor block corresponding to slot/unit specified by primary RP.

-

LOG_STD_ACTION

SONET-3-APSHAHOLDTIME

3-Error

[chars]: [chars]

Messages issued by HA APS when PGP holdtime is adjusted

-

"None - information only."

SONET-3-DELAYTIMER

3-Error

[chars]

Delay timer creation failure

-

LOG_STD_DDTS_TAC_DETAILS

SONET-3-BADTCA

3-Error

TCA signal [dec] is invalid

TCA software has malfunctioned.

-

LOG_STD_DDTS_TAC_DETAILS

SONET-3-BADTCATH

3-Error

TCA threshold [dec] is not supported

The specific TCA threshold is not supported

-

LOG_STD_DDTS_TAC_DETAILS

WANPHY-4-WANALARM

4-Warning

[chars]: [chars] [chars]

The specified WANPHY Alarm has been declared or cleared.

c7600-es-platform

"Recommended action is to repair the source of the alarm."

SNAPSHOT-2-BADSTATE

2-Critical

Bad state for Snapshot block [chars][[dec]] location [dec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

SNAPSHOT-2-TOOMANYDIALERS

2-Critical

Exceeded maximum dialer interfaces to watch. Ignoring [chars]

Snapshot is being used over more than 100 DDR interfaces.

-

"Do not use snapshot over more than 100 DDR interfaces."

FR_VIP-3-MISSING_STATE

3-Error

Missing state on VIP: DLCI [dec]: Slot [dec]

An error occurred while preparing an IPC stats unit

fr

"Shut - no shut the frame-relay encapsulated interface for the" "slot in question"

FR_VIP-3-INCONSISTENT

3-Error

Invalid state on VIP: DLCI [dec]: Slot [dec]: Error code [dec]

An error occurred while processing FR state on the VIP

fr

"Shut - no shut the frame-relay encapsulated interface for the" "slot in question"

FR_VIP-5-FLUSH

5-Notice

Flushing frame relay state

Clearing up frame relay state on the VIP card

fr

"Notification message only. No action required."

FR_VIP-3-SWITCHING

3-Error

[chars] DLCI [dec]: [chars]

An error was detected while switching a packet on the VIP

fr

"Shut - no shut of the interface in question or unconfigure then\n\ re-configure may solve the problem. Copy and save the message\n\ and call your technical support representative for assistance"

FR_LMI-3-INCORRECT_IE

3-Error

Enhanced LMI not configured incorrect IE

An unexpected LMI information element has been received.

fr

"Verify the configuration for enhanced LMI on the switch matches the c onfiguration on the router."

FR_LMI-3-MSG_TOO_BIG

3-Error

[chars] [chars] Status message too big status of PVCs with dlci values

LMI STATUS message size is too big to fit into interface MTU.

fr

"LMI type - cisco - does not support segmentation of STATUS message " "so either increase the interface MTU or use LMI types - ansi or " "q933a."

FR-5-DLCICHANGE

5-Notice

Interface [chars] - DLCI [dec] state changed to [chars]

The state of the Frame Relay PVC specified by the DLCI changed.

fr

"Notification message only. No action required."

FR-3-BQ_ENQ_ERR

3-Error

fr_oqueue: Invalid datagramstart [hec] [hec] pak dropped

A broadcast packet was detected in the Frame Relay output queue that contained an invalid datagram header. The packet has been dropped.

fr

"If the router or some features are not operational due to this" "condition attempt to disable the Frame Relay broadcast queue by " "entering the <CmdBold>no frame-relay broadcast-queue<NoCmdBold>" "command in interface configuration mode for a immediate workaround." "And "LOG_STD_ACTION

FR-3-BQ_DEQ_ERR

3-Error

fr_bq_proc: unknown packet on broadcast queue packet dropped!

Invalid packet on FR broadcast queue packet dropped!

fr

"If the router or some features are not operational due to this" "condition attempt to disable the Frame Relay broadcast queue by " "entering the <CmdBold>no frame-relay broadcast-queue<NoCmdBold>" "command in interface configuration mode for a immediate workaround." "And "LOG_STD_ACTION

FR-3-BQ_DEQ_PTR

3-Error

fr_br_proc: hdr-[hec] size-[dec] dlci-%4x %8x %8x

The Frame Relay broadcast queue contains a datagram that is invalid. The packet has been dropped.

fr

"Inform Cisco technical support representative"

FR-4-DLCIDELETE

4-Warning

Interface [chars] - DLCI [dec] - PVC use count [dec]

Trying to remove PVC DLCI while it is still being used.

fr

"If this error can be easily recreated enter the " "<CmdBold>debug frame-relay event<NoCmdBold> command and recreate " "the condition that caused this error. " "Copy all the debug messages text and the system message text " "exactly as it appears on the console or in the system log enter " "the show tech-support command contact your Cisco technical support " "representative and provide the representative with the gathered " "information."

FR-3-NOMEMORY

3-Error

No memory for [chars]

The requested operation could not be accomplished because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

FR-4-NNISUBINTF

4-Warning

Subinterface not supported on Frame Relay NNI

Trying to change the state of a subinterface on FR NNI.

fr

"Reconfigure the Frame Relay link type or remove the subinterface."

FR-3-FRTSZEROCIR

3-Error

FRTS: attempt to configure zero CIR

It should not be possible to configure a zero CIR. To do so would prevent data transmission on the VC.

fr

"Inform Cisco technical support representative"

FR-5-CONVERT_ROUTE

5-Notice

Converting route pair to connect

A pair of Frame Relay routes are being converted to connections.

-

LOG_STD_NO_ACTION

FR-3-NULL_PTR_DEREF

3-Error

Dereferencing NULL pointer [chars]

Dereferencing a NULL pointer

fr

"Inform Cisco technical support representative"

FR-3-MLPOFR_ERROR

3-Error

MLPoFR not configured properly on Link [chars] Bundle [chars] :[chars]

The configuration of MLPPP-over-Frame-Relay MLPoFR

fr

"Ensure that FRTS has been configured on physical interface and that " "the service policy has been attached to the Virtual Template. To " "verify the configuration use the <CmdBold>show running-config serial " "inteface<noCmdBold> and <CmdBold>show running-config " "virtual-template<noCmdBold> commands."

FR-3-SVC_SETUP

3-Error

[chars]: interface [chars]: DLCI [dec]

An error occurred while attempting to setup a Frame-Relay SVC. There may have been an attempt to setup a SVC using a DLCI thats already in use

fr

"Check if the DLCI is already in use. For example: A PVC may be " "configured to use the same DLCI " "use <CmdBold>show frame-relay pvc<CmdBold> to verify. "

FR-3-MFR_UNEXPECTEDEVENT

3-Error

MFR Timer process error: event table is NULL for event [dec] state [dec]

The event was ignored because the state transition table is NULL. Normal processing continue.

fr

"Please refer to Bug Toolkit on CCO to check for existing bugs. " "If you need further assistance please provide 'show version' and " "'show running' and any configurations that were being done at the " "time the message was seen. Copy the message text exactly as it " "appears on the console or in the system log. Inform Cisco technical " "support representative and provide the representative with the " "gathered information."

FR-3-FR_PVC_STATUS_Q_CREATE_ERROR

3-Error

FR PVC status event queue error: failed to create queue

Unable to create FR PVC status event queue

fr

LOG_STD_ACTION

FR-3-MAP_DELETE_ERROR

3-Error

[chars]

An error occurred while deleting a frame-relay map

fr

LOG_STD_ACTION

FR-3-FR_INV_OUTPUT_VECTOR

3-Error

An invalid output vector detected on interface [chars]

An invalid internal function vector is installed on a Frame Relay interface which affects the ability of processing outbound traffic on the device.

fr

"Remove and re-apply Frame Relay encapsulation on the interface to " "recover from the error."

FR_EEK-5-FAILED

5-Notice

Interface [chars] - DLCI [dec]

The end-to-end keepalive protocol has failed for the indicated PVC. A failure occurs when the DLCI is ACTIVE and end-to-end keepalives are enabled but the number of errors due to timeouts or sequence number mismatches has reached the failure threshold. The DLCI is taken out of operation until the protocol recovers.

fr

"A persistent failure may indicate a mismatched end-to-end keepalive " "configuration at each end of the PVC. A transient failure may be due " "to a temporary loss of connectivity or heavy congestion in the network. " "This is a rate-limited log message so not all failures may be logged. " "The <CmdBold>show frame-relay end-to-end keepalive failures<NoCmdBold> " "command can be used to obtain further information on what PVCs have " "experienced failures."

CEM-1-ISSU_NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low\n\ memory condition.

cemcommon

"Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration."

CEM-3-ISSU_SENDFAILED

3-Error

\nCEM ISSU: send message failed rc = [dec]\n

The sending of a message has failed.

cemcommon

LOG_STD_SH_TECH_ACTION

CEM-4-ISSU_INCOMPATIBLE

4-Warning

\ncem-issu-compat: returned FALSE

The compatibility checking has failed

cemcommon

LOG_STD_SH_TECH_ACTION

CEM-4-ISSU_XFORM

4-Warning

\n[chars]: failed rc=[chars]

The transform has failed.

cemcommon

LOG_STD_SH_TECH_ACTION

HDLC-1-ISSU_NOMEMORY

1-Alert

msgtxt_nomemory

The requested operation could not be accomplished because of a low memory condition.

-

"Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration."

HDLC-4-ISSU_SENDFAILED

4-Warning

\nHDLC ISSU: send message failed rc = [dec]\n

The sending of a message has failed.

-

LOG_STD_SH_TECH_ACTION

HDLC-4-ISSU_INCOMPATIBLE

4-Warning

\nhdlc-issu-compat: returned FALSE

The compatibility checking has failed

-

LOG_STD_SH_TECH_ACTION

HDLC-4-ISSU_XFORM

4-Warning

\n[chars]: failed rc=[chars]

The transform has failed.

-

LOG_STD_SH_TECH_ACTION

FR_FRAG-3-BADPAK

3-Error

Inconsistent packet: size [dec] linktype [chars] input [chars] output [chars]

A packet being fragmented has inconsistent size and data

fr

"Inform Cisco technical support representative"

SONET-4-UPSR

4-Warning

Protection-Group [dec] [chars] [chars]

There has been a protection switch on the protection group

-

"None - normal situation"

SDH-4-SNCP

4-Warning

Protection-Group [dec] [chars] [chars]

There has been a protection switch on the protection group

-

"None - normal situation"

ACCESS_IE-3-INVALID_HANDLE

3-Error

Caller passed in invalid handle - traceback to follow.

An invalid handle was encountered in the Access IE library.

-

LOG_STD_ACTION

WPM-3-WDB_ADD_FB

3-Error

Target of type [dec] failed to be created in WDB

Target can not be created in WDB

-

LOG_STD_ACTION

WPM-3-WPM_NODE_CREATE

3-Error

Create WPM FB node for Target type [dec] failed in WDB

Can not create WPM FB Node in WDB

-

LOG_STD_ACTION

WPM-3-WPM_RECONCILE_ABORT

3-Error

QoS HA reconcilation aborted due to timer event

QoS HA reconcilation aborted due to timer event

-

LOG_STD_ACTION

LAPB-3-NULLPAK

3-Error

Interface [chars] NULL packet ptr rvr [dec] vs [dec] vr [dec]

An internal software error occurred.

lapb

"If either of these messages recur call your technical support\n\ representative for assistance."

LAPB-3-NOINPIDB

3-Error

Input idb not set

An internal software error occurred.

lapb

"If either of these messages recur call your technical support\n\ representative for assistance."

LAPB-4-FRAMEERR

4-Warning

Interface [chars] Frame error: CF [hex] VS [dec] [chars] VR [dec] Reason [hex]

-

lapb

-

LAPB-4-INFOBAD

4-Warning

Interface [chars] Info field not permitted

A received FRMR frame reported that an information field was present\n\ in a frame where no information field is allowed.

lapb

"Check the serial line and the device attached to the line."

LAPB-4-CTRLBAD

4-Warning

Interface [chars] Invalid control field

A received FRMR reported a frame with an invalid control code.

lapb

"Check the serial line and the devices attached to the line."

LAPB-4-N1TOOBIG

4-Warning

Interface [chars] N1 too large

A received FRMR reported an information frame that was too long.

lapb

"Verify that the equipment attached to the serial line is configured\n\ with the same N1 value. N1 is in bits and includes the entire frame\n\ plus 16 bits of CRC. However some equipment may require configuration\n\ in octets the omission of the two CRC octets or the omission of the\n\ three octets of LAPB control information."

LAPB-4-INVNR

4-Warning

Interface [chars] Invalid NR value

A received FRMR reported a frame with an invalid NR value.

lapb

"Verify that the equipment attached to the serial line is configured\n\ with the same K value maximum number of outstanding I frames."

LAPB-2-NOBUF

2-Critical

Interface [chars] no buffer available to [chars]

There was insufficient memory for the LAPB protocol engine to send a\n\ message.

lapb

"This message is acceptable if it occurs infrequently because the LAPB\n\ protocol is designed to handle loss of frames. Frequent occurrences can\n\ cause disruption of service. The system can be configured to ease\n\ memory demands or if conditions warrant the system can be upgraded to\n\ a larger memory configuration."

LAPB-3-BADPAYLOAD

3-Error

Interface [chars] Invalid payload value: [chars]

An internal software error occurred.

lapb

"If either of these messages recur call your technical support\n\ representative for assistance."

LAPB-3-CONTEXTERR

3-Error

[chars]: [chars]

An internal software error occurred.

lapb

"If either of these messages recur call your technical support\n\ representative for assistance."

LAPB-3-TIMERERR

3-Error

LAPB timer task cannot be created

An internal software error occurred.

lapb

"If either of these messages recur call your technical support\n\ representative for assistance."

COMP-5-NOBUF

5-Notice

Interface [chars] [chars]

Interface serial0 compression getbuffer failed causing Link Access\n\ Procedure Balanced LAPB retransmissions.

-

"Configure additional large and big buffers."

COMP-3-SYNCBAD

3-Error

Interface [chars] Decompression sync error

One interface is configured for predictor compression the other is\n\ not.

-

"Configure both interfaces for predictor compression."

COMP-3-VERSIONBAD

3-Error

Interface [chars] Compression Version mismatch expected [hec] received [hec]

One interface is configured for predictor compression the other is\n\ not.

-

"Configure both interfaces for predictor compression."

COMP-3-SIZEBAD

3-Error

Interface [chars] Decompression size error

One interface is configured for predictor compression the other is\n\ not.

-

"Configure both interfaces for predictor compression."

COMP-3-COMPERR

3-Error

[chars]: COMPRESS: stac error! status: [dec] size in: [dec] size out: [dec]

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

COMP-3-CONFIGBAD

3-Error

Interface [chars] Compression internal configuration error

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

COMP-3-BADCOMP

3-Error

Interface [chars] Bad status returned from packet compression operation

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

COMP-3-SUBBLOCKERR

3-Error

Interface [chars] compression subblock creation failed.

An internal software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

X25-2-ILLP4

2-Critical

Interface [chars] Illegal state [chars] when P4

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

X25-3-NOLCI

3-Error

Interface [chars] Delete: lci [dec] not found in [chars] table

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

X25-3-UNKNOWNPROT

3-Error

[chars] : Unable to identify lower layer protocol

IDB is not using X25 and IDB is not capable of supporting CMNS.

-

"Check your hardware configuration or contact your technical support\n\ representative for assistance."

X25-3-X25NOTAVAIL

3-Error

[chars] : Lower layer protocol is not available

The required lower layer service is unavailable.

-

"Check your configuration or contact your technical support\n\ representative for assistance."

X25-3-BADCONFIGATTEMPT

3-Error

Attempt to [chars].

The user attempted an illegal configuration.

-

"The error will indicate what illegal action was attempted.\n\ The user should check their configuration and if necesarry\n\ contact technical support representative for assistance."

X25-3-NOTFINDBH

3-Error

Can't find bfe host address [inet] to delete

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

X25-3-INTIMEQ

3-Error

Interface [chars] LCN [dec] already in timer queue new time %#Ta

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

X25-3-BADCONFIG

3-Error

Interface [chars] X.25 [chars] current config. retained

-

-

-

X25-3-PVCBAD

3-Error

Interface [chars] PVC [dec] [chars]

A switched PVC cannot be connected. The final [chars] text string in\n\ the message represents the state of the PVC. These text strings can\n\ also appear in show x25-vc output. For more information refer to the\n\ show x25-vc documentation in the Router Products Command Reference\n\ publication.

-

"Validate the configuration of the PVCs at both ends of the connection\n\ and reconfigure them if necessary."

X25-3-XOTPROTOCOL

3-Error

XOT protocol error from [inet]: [chars]

-

-

"If this message recurs call your technical support representative for\n\ assistance."

X25-4-VCLOSTSYNC

4-Warning

Interface [chars] VC [dec] TCP connection [chars]

An X.25 circuit that is being tunneled over a TCP connection between\n\ routers was cleared ungracefully. The last [chars] text string in the\n\ message can take one of two forms. If the text string is \closed\n\ unexpectedly

-

-

X25-4-BADUPCALL

4-Warning

Interface [chars] Unexpected call [chars] from LLC2

An internal software error occurred.

-

"If any of these messages recur call your technical support\n\ representative for assistance."

X25-4-DEBUG_LCI

4-Warning

LCI deleted at interrupt time

The interface's default packet sizes or outgoing packet size facility\n\ values are too large to be carried by Link Access Procedure Balanced\n\ LAPB.

-

[chars] packet sizes [dec]/[dec] too large

X25-4-PARTIALMAP

4-Warning

Interface [chars] [chars] encapsulation call from [chars] partially mapped to [chars]

-

-

"Modify the configuration of the router or the far host to match the\n\ encapsulation method used."

X25-5-NOBUF

5-Notice

Interface [chars] LCI [dec] [chars]

-

-

"If this message occurs frequently you may need to modify the buffer\n\ pool. Copy the message exactly as it appears and report it your\n\ technical support representative."

X25-5-PBPHOLDQ

5-Notice

Interface [chars] LCI [dec] X25 Hold queue needs to be at least default size

An attempt was made to configure the X.25 hold queue to less than the\n\ minimum value.

-

"Configure the X.25 hold queue to be ten or more."

X25-5-PBPDBIT

5-Notice

Interface [chars] LCI [dec] PBP Compression does not support X25 D bit

Compression is not enabled because D-bit support is configured for the\n\ LCI.

-

"Reconfigure without D-bit support or do not attempt to run with\n\ compression."

X25-3-SYNCBAD

3-Error

Interface [chars] LCI [dec] Decompression sync error. expected [dec] got [dec]

An internal software error occurred. The PBP header has a sync field.\n\ The sync field 8 bits is checked on each received packet.

-

"Contact your technical support representative for assistance."

X25-3-VERSIONBAD

3-Error

Interface [chars] LCI [dec] Compression Version mismatch expected [hec] received [hec]

An internal software error occurred. The PBP header has a mismatched\n\ version field. The version is checked on each received packet.

-

"Copy the message exactly as it appears and report it your technical\n\ support representative."

X25-3-SIZEBAD

3-Error

Interface [chars] LCI [dec] Decompression size error

An internal software error occurred. The PBP header has an\n\ uncompressed packet size field. Each uncompressed packet size is\n\ checked against this field.

-

"Contact your technical support representative for assistance."

X25-5-PBPNOEND

5-Notice

Interface [chars] LCI [dec] End system not configured for X25 PBP

A compression or decompression operation was attempted by a router\n\ other than an end router. Only end routers can perform compression and\n\ decompression.

-

"Reconfigure the routers so that only the end routers in the network\n\ perform compression and decompression."

X25-3-COMPERR

3-Error

Interface [chars] LCI [dec] low-level stac compression error

A Stacker compression algorithm internal error or shortage of buffer\n\ space was encountered during a compression operation. This should never\n\ happen.

-

"Report the error to your technical support representative."

X25-4-BADMBIT

4-Warning

Interface [chars] VC [dec] partial data packet has M-bit set

This message occurs when a virtual circuit is set up using the default\n\ maximum packet sizes but the DTE and DCE are not configured with the\n\ same default values. A packet was received that had the M-bit set\n\ signifying that more data follows but the packet did not carry the\n\ maximum number of bytes allowed. Such partial data packets must have\n\ the M-bit cleared. The resulting loss of a message boundary might cause\n\ problems for the data recipient.

-

"Verify the default flow control parameters of the DTE and the DCE. If\n\ this message recurs call your technical support representative for\n\ assistance."

X25-3-ADDRESSBAD

3-Error

Interface [chars] x25 address [chars] subaddress [chars] is too long

This message occurs when a subaddress is configured. When this\n\ subaddress is combined with the interface's X.121 address the total\n\ address exceeds the limit of 15 characters.

-

"Reconfigure the subaddress so that this does not happen."

X25-3-ERR_SUBST_XOT_DNS_DEST

3-Error

Error substituting regular expression for XOT DNS destination pattern

This message occurs when the regular expression substitute utility fails to arrive at X.25 hostname pattern to be sent to DNS for address resolution

-

"Correct the X.25 route command's DNS substitution pattern"

X25-3-TRUNCATE_ALT_XOT_DNS_DEST

3-Error

Truncating excess XOT addresses [dec] returned by DNS

-

-

-

X25-4-XOTPVCDUPLICATE

4-Warning

Duplicated remote PVC data for {[chars] pvc [dec]} and {[chars] pvc [dec]}

This message identifies two local XOT PVCs that are defined using\n\ duplicate specifications for the connecting remote XOT PVC.

-

-

X25-4-BFEIP

4-Warning

Warning: IP address is missing or incompatible with BFE mode

An interface configured for X.25 BFE mode does not have an\n\ IP address configured or the IP address does not conform to \n\ BFE requirements so cannot be mapped to an X.121 address.

-

"Please configure a valid Class A IP address for the interface \n\ or remove the 'bfe' option from the 'encapsulation x25' command \n\ for the interface."

X25-3-X25INT

3-Error

Interface [chars] X.25 internal error [chars]

This is a general message covering numerous internal X25\n\ error conditions. The message text contains additional\n\ details that can be used to identify the problem.

-

LOG_STD_RECUR_ACTION

X25-3-XOTINT

3-Error

XOT internal error [chars]

This is a general message covering numerous internal error\n\ conditions related to XOT. The message text contains additional\n\ details that can be used to identify the problem.

-

-

X25-3-PROFILENO

3-Error

profile [chars] does not exist

This message occurs when an X.25 interface is configured to use\n\ an X.25 profile that does not exist

-

"Create and configure the x25 profile using x25 profile <name>\n\ global subcommand before referencing the profile."

X25-3-X25NOCFG

3-Error

Profile is not configured

This message occurs when an X.25 interface is configued to use\n\ an X.25 profile that isn't configured

-

"Configure the x25 profile using x25 profile <name>\n\ global subcommand before referencing the profile."

X25-3-X25ENCINV

3-Error

[chars]

This message occurs when configuring an X.25 service.

-

LOG_STD_ACTION

X25-3-X25DEENCINV

3-Error

[chars]

This message occurs when deconfiguring X.25 service.

-

LOG_STD__ACTION

X25-3-INVCFGID

3-Error

[dec] is not a valid X.25 configuration ID

This message occurs when an invalid configuration id is used

-

LOG_STD_ACTION

X25-5-UPDOWN

5-Notice

Interface [chars] - DLCI [dec] X.25 packet layer state changed to [chars]

The state of the X.25 context associated with the DLCI changed

fr

"Notification message only. No action required"

X25-7-DIAGEVENT

7-Debug

Interface [chars] X.25 diagnostic event [chars] lci [dec][chars]

-

-

-

X25-7-DIAGRX

7-Debug

Interface [chars] X.25 Diagnostic received [chars][chars]

-

-

-

X25-5-CALL_RECORD

5-Notice

[chars]

This message contains X.25 call record information.

x25

LOG_STD_NO_ACTION

PAD-3-GETLINE

3-Error

Tty[t-line] bad return code [dec] from x3_getline

An internal software error occurred.

-

"If this message recurs copy the error message exactly as it\n\ appears and report it to your technical support representative."

PAD-2-PUTSETUP

2-Critical

Tty[t-line] buffer already setup

An internal software error occurred.

-

"If this message recurs copy the error message exactly as it\n\ appears and report it to your technical support representative."

PAD-2-INTR

2-Critical

[chars] called at interrupt level [hec]

An internal software error occurred.

-

"If this message recurs copy the error message exactly as it\n\ appears and report it to your technical support representative."

SW_MGR-3-INVALID_HANDLE

3-Error

Segment Manager Error - Invalid [chars] handle - [dec].

A Connection Manager error occurred due to a invalid handle.

-

LOG_STD_ACTION

SW_MGR-3-INVALID_SEGMENT

3-Error

Segment Switch Manager Error - Invalid segment - [chars].

A Segment Switch Manager error occurred due to a invalid segment.

-

LOG_STD_ACTION

SW_MGR-3-CM_ERROR_CLASS

3-Error

Connection Manager Error: Class [chars]: - [chars].

A Segment Switch Connection Manager error occurred.

-

LOG_STD_ACTION

SW_MGR-3-CM_ERROR

3-Error

Connection Manager Error - [chars].

A Segment Switch Connection Manager error occurred.

-

LOG_STD_ACTION

SW_MGR-3-SM_ERROR

3-Error

Segment Manager Error - [chars].

A Segment Manager error occurred.

-

LOG_STD_ACTION

SW_MGR-3-FHM_ERROR

3-Error

SSM Feature Handler Manager Error - [chars].

A Feature Handler Manager error occurred.

-

LOG_STD_ACTION

SW_MGR-3-CM_ERROR_FEATURE_CLASS

3-Error

Connection Manager Feature Error: Class [chars]: [chars] - [chars].

-

-

-

SW_MGR-3-CM_ERROR_FEATURE

3-Error

Connection Manager Feature Error: [chars] - [chars].

-

-

-

SW_MGR-3-SSM_SEG_ISSU

3-Error

SSM Segment ISSU: [chars] not supported.

ISSU of this SSM Segment is not supported.

-

LOG_STD_NO_ACTION

SW_MGR-3-XDRREGISTRATION

3-Error

XDR failed to register [chars] client due to [chars]

Failure to register the said XDR client.

-

LOG_STD_NO_ACTION

GRIP-3-BADPATHS

3-Error

Invalid number of paths [dec] for %q

An internal inconsistency was detected in the XNS routing table\n\ structure.

-

"Note the parameters associated with this message and call your\n\ technical support representative for assistance."

GRIP-2-BADROUTE

2-Critical

Error [chars] route - null table

A hardware or software error occurred.

-

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

ZONE-4-API

4-Warning

Zone [chars] [chars][chars] [chars] failed to notify the data plane

The notification of a zone operation has failed to update the data\n\ plane and as such the application of the zone information within the\n\ object will not be applied to the data plane. It is also possible\n\ that the common classification may fail to locate and bind to the\n\ zone rendering the configuration inconsistent in terms of\n\ application.

zone

show memory

ZONE-6-CONFIG

6-Information

Zone security [chars] is removed due to VRF config change on interface [chars]

The notification of a zone is removed from an interface\n\ due to a vrf is removed from the interface

zone

show running

ZONE-4-LICENSE

4-Warning

License smart enable and zone-license enable should be enabled first

The notification indicates that zone smart license\n\ should be enabled

zone

show running

-

-

-

-

-

-

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ this is only a warning

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

EVENTLIB-3-CPUHOG

3-Error

[chars]: [dec]ms Traceback=[chars]

This error occurs when a particular event consumes an unfair share of the CPU that may degrade overall system response time.

asr1k-xe-infra

show platform software process event

EVENTLIB-3-RUNHOG

3-Error

[chars]: [dec]ms Traceback=[chars]

This error occurs when a particular event consumes an overall unfair share of the CPU that may degrade overall system response time.

asr1k-xe-infra

show platform software process event

EVENTLIB-3-TIMEHOG

3-Error

[chars]: %llums Traceback=[chars]

This error occurs when a particular event takes an unusually long time to complete. This may affect overall system response time.

asr1k-xe-infra

show platform software process event

EVENTLIB-3-HISTSUMM

3-Error

dispatch start: %llums elapsed time: %llums detected hog: [dec] set count: [dec]

This event summary is part of a CPUHOG or TIMEHOG error providing diagnostic details useful to engineering. Save this summary message along with the HOG error.

mcp-infra

LOG_STD_DDTS_TAC_DETAILS

EVENTLIB-3-HISTELEM

3-Error

elem[[dec]] event: [chars] [chars] set: %llums unset: %llums hog check: [dec] caller: %p app-info: [chars]

This event element is part of a CPUHOG or TIMEHOG error providing diagnostic details useful to engineering. Save all element messages along with the HOG error.

mcp-infra

LOG_STD_DDTS_TAC_DETAILS

EVENTLIB-3-EVFDREAD

3-Error

Event notification read failed with err [chars]

This occurs when we fail to read a thread notify event

polaris-infra

LOG_STD_DDTS_TAC_DETAILS

CPP_NGIO-5-NGIO_FC_PRIORITY

5-Notice

NGIO flow control msg processed at reduced priority mod pid:[dec]

Flow control message from module was not properly prioritized.

cpp-ucode

LOG_STD_ACTION

CPP_NGIO-5-NGIO_PKT_PRIORITY

5-Notice

NGIO packet processed at flow control priority mod pid:[dec]

Data packet from module was not properly prioritized.

cpp-ucode

LOG_STD_ACTION

CPP_NGIO-3-NGIO_MOD_PID

3-Error

NGIO flow control msg received with no config matching module pidmod pid:[dec]

Flow control message received could not be matched with a module.

cpp-ucode

LOG_STD_RECUR_ACTION

CPP_NGIO-3-NGIO_FC_IID

3-Error

NGIO flow control ID lookup failed:[chars] module pid/iid:[dec]/[dec]

Flow control message from module contained an invalid identification field

cpp-ucode

LOG_STD_RECUR_ACTION

CPP_NGIO-3-NGIO_FC_BADPATH

3-Error

NGIO flow control msg received on unexpected code path mod pid [dec]

Flow control message received on unexpected code path

cpp-ucode

LOG_STD_RECUR_ACTION

CCE-3-HW_TCAM_CONTROLLER

3-Error

Datapath classification program flow error: invalid TCAM controller 0x%lx

Cisco internal software error. The dataplane detected a classification request providing an invalid TCAM controller value. The program flow Traceback

qfp-infra-internal keyword:cce

LOG_STD_ACTION

CCE-3-HW_CCE_TCAM_CONFIG_IPV4

3-Error

Control Plane classification config error: TCAM device not specified: [chars] [chars] Ipv4 src %Ci dst %Ci

Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error

qfp-infra-internal keyword:cce

LOG_STD_ACTION

CCE-3-HW_CCE_TCAM_CONFIG_IPV6

3-Error

Control Plane classification config error: TCAM device not specified: [chars] [chars] IPv6 src [ipv6_addr] dst [ipv6_addr]

Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error

qfp-infra-internal keyword:cce

LOG_STD_ACTION

CCE-3-HW_CCE_TCAM_CONFIG_IPV6_EXT

3-Error

Control Plane classification config error: TCAM device not specified: [chars] [chars] IPv6_ext src [ipv6_addr] dst [ipv6_addr]

Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error

qfp-infra-internal keyword:cce

LOG_STD_ACTION

CCE-3-HW_CCE_TCAM_CONFIG_IPV6_COMPR

3-Error

Control Plane classification config error: TCAM device not specified: [chars] [chars] IPv6 compression src [ipv6_addr] dst [ipv6_addr]

Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error

qfp-infra-internal keyword:cce

LOG_STD_ACTION

CCE-3-HW_CCE_TCAM_CONFIG

3-Error

Control Plane classification config error: TCAM device not specified: MPLS or Layer2 [chars] [chars]

Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error

qfp-infra-internal keyword:cce

LOG_STD_ACTION

HAL_GENMEM-2-BAD_OPCODE

2-Critical

Opcode=[hec]

A bad Opcode was received by the general memory manager.

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-2-ALLOC_FAIL

2-Critical

rc 0x[hec]

A critical failure occurred when trying to obtain packet memory

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-2-OUT_OF_RESOURCES

2-Critical

Packet buffer memory is low packets are being dropped

Packet buffer memory is low packets are being dropped

cpp-ucode

LOG_STD_ACTION

INFRA-3-INVALID_GPM_ACCESS

3-Error

Invalid GPM [chars] at [hec] HAL start [hec] HAL end [hec] INFRA start [hec] INFRA [hec] NET [hec]

Processing packet went beyond valid packet data packet was possibly invalid ppe info and encrypted pkt dump follow

cpp-ucode

LOG_STD_ACTION

INFRA-3-INVALID_GPM_ACCESS_INFO

3-Error

%08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x

Registers associated with previous exception error

-

LOG_STD_ACTION

INFRA-3-INVALID_GPM_ACCESS_DATA

3-Error

-

Packet associated with previous exception error The packet data has been encrypted

cpp-ucode

LOG_STD_ACTION

INFRA-3-L1L2_ICACHE_ERROR

3-Error

thread=[dec] reg=[chars] addr=0x%llx val=0x[hec]

L1/L2 ICACHE error possibly recoverable

cpp-ucode

LOG_STD_ACTION

INFRA-3-L0I_FETCH_ERROR

3-Error

thread=[dec] PC=0x[hec]

Level-0 instruction cache fetch error possibly recoverable

cpp-ucode

LOG_STD_ACTION

CD_FFP_IPSEC_PROXY-2-FFP_INIT_FAILED

2-Critical

FFP Crypto device Proxy Agent initialization failure result: [dec].

Cisco internal software error. FFP Crypto device Procy Agent initialization detected critical failure. FFP Crypto device software library will not be functional while this condition exists.

ffp-ipsec keyword:datapath

LOG_STD_ACTION

CD_FFP_IPSEC_PROXY-2-FFP_PROXY_INIT_FAILED

2-Critical

FFP Crypto device Procy Agent Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. FFP Crypto device Procy Agent Proxy initialization detected that the IPC interface initialization failed. FFP Crypto device Procy Agent proxy will not be functional while this conidtion exists.

ffp-ipsec keyword:datapath

LOG_STD_ACTION

CD_FFP_IPSEC_PROXY-3-FFP_PROXY_IPSEC_SA_CRT_FAILED

3-Error

FFP Crypto device Procy Agent Proxy IPSec SA create failure result: [dec].

Cisco internal software error. FFP Crypto device Procy Agent Proxy message processing detected IPSec SA create failure. The request is rejected as the result of this condition.

ffp-ipsec keyword:datapath

LOG_STD_ACTION

CD_FFP_IPSEC_PROXY-3-ESG_IPSEC_KAT_TEST_FAILED

3-Error

Cryptographic Known-Answer Test failure result: [chars]

Cisco internal software error. Cryptographic Known-Answer Tests. Error due to one of the Cryptographic Power-on Self-tests Known-Answer Tests not returning the expected value.

esg-ipsec keyword:datapath

LOG_STD_ACTION

FFP_HW_IRQ-3-NON_FATAL_INTERRUPT

3-Error

%lu errors in the last %lu seconds

Accumulation of Cavium hardware-generated error

cpp-ucode

LOG_STD_ACTION

FFP_HW_IRQ-3-TOO_MANY_NON_FATAL_INTERRUPTS

3-Error

-

Aborting due to too many Cavium hardware-generated errors

cpp-ucode

LOG_STD_ACTION

PORT_INIT_10G-2-PHY_NOT_READY_TIMEOUT

2-Critical

front panel 10G port init error: PHY ready not received within %llu seconds

front panel 10G interface init failure due to timeout

cpp-ucode

LOG_STD_ACTION

PORT_INIT_10G-2-PHY_NOT_READY_TIMEOUT

2-Critical

-

-

-

-

HW_FLOWDB-3-HW_FLOWDB_OOM

3-Error

FlowDB memory usage exceeded 95%% usage. OOM condition can occur.

FlowDB running low on memory. Out-of-memory condition can occur

cpp-ucode

"Check sw-distrib for actual utilization of FlowDB memory"

HW_FLOWDB-3-HW_FLOWDB_NULL_FEATOBJ

3-Error

FlowDB featobj install attempted with invalid pointer.

A feature attempted to install a NULL feature object pointer in flowDB

-

"Bug in feature code track down why this happened"

HW_FLOWDB-3-HW_FLOWDB_DBLDEL_FEATOBJ

3-Error

FlowDB featobj cannot be deleted twice.

A feature attempted to remove a feature object pointer in flowDB that was already removed

-

"Bug in feature code track down why this happened"

HW_FLOWDB-3-HW_FLOWDB_DBLINSTALL_FEATOBJ

3-Error

FlowDB featobj cannot be installed twice.

A feature attempted to install a feature object pointer in flowDB that was already populated

-

"Bug in feature code track down why this happened"

HW_FLOWDB-3-HW_FLOWDB_VALIDATE_NO_MATCH

3-Error

FlowDB failed to find matching flow during validation.

A feature attempted to validate an installed flow.

-

"No recommended action. Output is used as a debug aid."

HW_FLOWDB-3-HW_FLOWDB_STALE_FEATOBJ

3-Error

FlowDB featobj remove attempted on stale entry.

A feature attempted to remove a feature object pointer in flowDB from a stale flow

-

"Bug in feature code track down why this happened"

HW_FLOWDB-3-HW_FLOWDB_INVALID_FEATOBJ

3-Error

FlowDB core [dec] detected invalid featobj owned by core [dec].

A feature attempted to validate a BAD feature object pointer in flowDB

-

"Bug in feature code track down why this happened"

HW_FLOWDB-3-HW_FLOWDB_NOT_OWNER

3-Error

FlowDB featobj remove attempted on core not owning flow.

A feature attempted to remove a featobj from a BAD flowDB entry

-

"Bug in feature code track down why this happened"

POSIX_PMD-3-MBUF_REDUCE

3-Error

Failed to allocate [dec] packet buffers. Reduced to [dec].

Cisco internal software error. The dataplane was unable to allocate the maximum number of packet buffers. This is likely due to memory fragmentation condition.

cpp-ucode

LOG_STD_ACTION

COFF_INFRA-3-COFF_DECRYPT_RCY_PUNT

3-Error

COFF attempted to punt pending decryption through RX-CR unsupported operation

We tried to do a punt with a pending decryption scheduled

cpp-ucode

"File a bug with the COFF infra team"

COFF_INFRA-3-COFF_MD_OOM

3-Error

COFF attempted to allocate an MD object and failed

MD pool ran dry and alloc failed

cpp-ucode

"Check 'sh plat hard qfp act da inf coff' CLI for MD mempool statistics"

COFF_INFRA-3-COFF_SQNMGMT_OOM

3-Error

COFF attempted to allocate an SQN Mgmt object and failed

SQN Mgmt pool ran dry and alloc failed

cpp-ucode

"Check 'sh plat hard qfp act da inf coff' CLI for SQN Mgmt mempool statistics"

POSIX_FIXUP-4-FIXUP_OCCURRED

4-Warning

alignment fixup @ PC=0x[hec] #hits=[dec] fault addr 0x[hec]

A misalignment was handled by a fixup signal handler

-

-

HW_TIME-2-HB_TICK_DISCARD

2-Critical

%llums since last timer heartbeat processed

Something caused us to go long durations without processing timer heartbeats

-

"sh plat hard qfp act da inf time basic"msgdef_tac_details

DCA_INFRA-3-DCA_ASYN_CB_SEQ_MISMATCH

3-Error

DCA received an asyn callback with an unexpected sequence number trans_id: [dec]

DCA received an asyn callback with an unexpected sequence number

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_ASYN_CB_STATE_MISMATCH

3-Error

DCA received an asyn callback while in an unexpected state trans_id: [dec]

DCA received an asyn callback while in an unexpected state

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_ASYN_CB_ERROR_RSP

3-Error

DCA received an asyn callback with an error response trans_id: [dec] Result: [dec]

DCA received an asyn callback with an error response

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_STATE_TRANS_FAIL

3-Error

DCA encountered an state transition error trans_id: [dec] Result: [dec]

DCA encountered an state transition error

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_STATE_TRANS_ERROR

3-Error

DCA encountered an error during state transition processing trans_id: [dec]

DCA encountered an error during state transition processing

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_REQUEST_WHILE_BUSY

3-Error

DCA received a new request while previous request in progress

DCA received a new request while previous request in progress

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-2-DCA_PROXY_IPC_INIT_FAILED

2-Critical

DCA IPC initialization failure result: [dec].

Cisco internal software error. DCA initialization detected that the Proxy IPC interface initialization failed.

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-2-DCA_PROXY_IPC_SEND_FAIL

2-Critical

DCA IPC response send failure result: [dec].

Cisco internal software error. DCA detected an error when sending a IPC response.

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_INV_PROXY_MSG

3-Error

DCA Proxy received invalid Message ID [dec]

Cisco internal software error. DCA Proxy received an invalid Message ID. This message will be ignored.

esg-dp-infra

"File a bug with the platform DCA infra team"

DCA_INFRA-3-DCA_PROXY_IPC_ALLOC_FAIL

3-Error

DCA Proxy [chars] response lost due to buffer allocation failure

Cisco internal software error. DCA Proxy message processing detected a IPC buffer allocation failure during response processing. The associated DCA functionality may not be fully functional as a result of this condition.

esg-dp-infra

"File a bug with the platform DCA infra team"

POSIX_FIXUP-4-FIXUP_OCCURRED

4-Warning

alignment fixup @ PC=0x%08x #hits=[dec] fault addr 0x%08x

A misalignment was handled by a fixup signal handler

-

-

POSIX_DPDK-3-HPAGE_MIN

3-Error

[dec]MB does not meet [dec]MB minimum memory reservation. Performance may be impacted.

Cisco internal software error. The dataplane was unable to allocate the minimum number of hugepages. This could be caused by insufficient reservation or hugepages being consumed by other processes.

cpp-ucode

LOG_STD_ACTION

POSIX_DPDK-3-NUMA_NODES

3-Error

Expected 1 CPU socket detected [dec]. Performance may be impacted.

Virtual machine configuration issue. The dataplane detected multiple NUMA nodes. This is caused by the guest configuration of the hyper-visor.

cpp-ucode

LOG_STD_ACTION

HAL_GPM-3-PREALLOC_FAIL

3-Error

offset 0x%08lx retcode [dec]

A critical failure occurred when trying pre-allocate GPM

cpp-ucode

LOG_STD_ACTION

HAL_GENMEM-3-HAL_MISMATCHED_GENMEM

3-Error

VADDR:%lu LINE: [dec]

Mismatched genmem.

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-2-ALLOC_FAIL

2-Critical

rc 0x[hec]

A critical failure occurred when trying to obtain packet memory

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-5-UTILIZATION_NOTICE

5-Notice

making adjustments to conserve [chars] buffer resources.

Packet buffer utilization is substantial.

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-4-UTILIZATION_WARNING

4-Warning

making more aggressive adjustments to conserve [chars] buffer resources.

Packet buffer utilization is at a risky level.

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-3-UTILIZATION_SEVERE

3-Error

making very aggressive adjustments to conserve [chars] buffer resources.

Packet buffer utilization is at a severe level.

cpp-ucode

LOG_STD_ACTION

HAL_PKTMEM-2-OUT_OF_RESOURCES

2-Critical

-

Packet buffer memory is low packets are being dropped

cpp-ucode

LOG_STD_ACTION

INFRA-3-INVALID_GPM_ACCESS

3-Error

Invalid GPM [chars] at [hec] HAL start [hec] HAL end [hec] INFRA start [hec] INFRA [hec] NET [hec]

Processing packet went beyond valid packet data packet was possibly invalid ppe info and encrypted pkt dump follow

cpp-ucode

LOG_STD_ACTION

INFRA-3-INVALID_GPM_ACCESS_INFO

3-Error

%08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x

Registers associated with previous exception error

-

LOG_STD_ACTION

INFRA-3-INVALID_GPM_ACCESS_DATA

3-Error

-

Packet associated with previous exception error The packet data has been encrypted

cpp-ucode

LOG_STD_ACTION

HAL_PACKET-3-HAL_GATHER_ASYNC_WAIT_TIMEOUT

3-Error

seqnum=%lu pak-type=%lu

Packet Hardware Transmit Error

cpp-ucode

LOG_STD_ACTION

CD_SW_IPSEC_SHIM-2-SHIM_INIT_FAILED

2-Critical

QFP Crypto device software library initialization failure result: [dec].

Cisco internal software error. QFP Crypto device software library initialization detected critical failure. QFP Crypto device software library will not be functional while this condition exists.

ultra-ipsec keyword:datapath

LOG_STD_ACTION

CD_SW_IPSEC_SHIM-2-SHIM_PROXY_INIT_FAILED

2-Critical

QFP Crypto device software library Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP Crypto device software library Proxy initialization detected that the IPC interface initialization failed. QFP Crypto device software library proxy will not be functional while this conidtion exists.

ultra-ipsec keyword:datapath

LOG_STD_ACTION

CD_SW_IPSEC_SHIM-3-SHIM_PROXY_IPSEC_SA_CRT_FAILED

3-Error

QFP Crypto device software library Proxy IPSec SA create failure result: [dec].

Cisco internal software error. QFP Crypto device software library Proxy message processing detected IPSec SA create failure. The request is rejected as the result of this condition.

ultra-ipsec keyword:datapath

LOG_STD_ACTION

CD_SW_IPSEC_SHIM-2-KAT_TEST_FAILED

2-Critical

QFP Crypto device software library kat test failure result: [dec].

Cisco internal software error. QFP Crypto device software library detected critical failure. QFP Crypto device software library will not be functional while this condition exists.

ultra-ipsec keyword:datapath

LOG_STD_ACTION

CD_SW_SSL_SHIM-2-SHIM_INIT_FAILED

2-Critical

QFP Crypto device software library initialization failure result: [dec].

Cisco internal software error. QFP Crypto device software library initialization detected critical failure. QFP Crypto device software library will not be functional while this condition exists.

ultra-ssl keyword:datapath

LOG_STD_ACTION

CD_SW_SSL_SHIM-2-SHIM_PROXY_INIT_FAILED

2-Critical

QFP Crypto device software library Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP Crypto device software library Proxy initialization detected that the IPC interface initialization failed. QFP Crypto device software library proxy will not be functional while this conidtion exists.

ultra-ssl keyword:datapath

LOG_STD_ACTION

CD_SW_SSL_SHIM-3-SHIM_PROXY_SSL_CTX_ALLOC_FAILED

3-Error

QFP Crypto device software library Proxy IPSec CTX create failure result: [dec].

Cisco internal software error. QFP Crypto device software library Proxy message processing detected IPSec CTX create failure. The request is rejected as the result of this condition.

ultra-ssl keyword:datapath

LOG_STD_ACTION

BFD_OFFLOAD-3-INIT_FAILED

3-Error

Initialization of the BFD Offload feature in QFP failed

Initialization of the BFD Offload feature in the QFP failed. This indicates a software failure.

asr1k-bfd

LOG_STD_ACTION

BFD_OFFLOAD-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for BFD Offload feature in QFP

Allocation of memory by the QFP BFD Offload feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

asr1k-bfd

LOG_STD_ACTION

BFD_OFFLOAD-3-PKT_REPLICA_INIT_FAILED

3-Error

Failed to register with generic packet replication for BFD Offload feature in QFP

BFD Offload initialization of packet replication registration failed.

asr1k-bfd

LOG_STD_ACTION

BFD_OFFLOAD-3-HA_INVALID_STATE

3-Error

state [dec]

An invalid HA state was received from the HA infrastructure.

cpp-ucode

LOG_STD_ACTION

BFD_OFFLOAD-3-HA_BULK_SYNC_FAIL

3-Error

rg [dec]

There was a failure such that BFD Offload domain bulk sync did not occur

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. FTP64 ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-BAD_L7_DATA

3-Error

-

Receive Bad L7 data from either FW or NAT.

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-INCORRECT_HA_MAGIC

3-Error

rcvd:[hec] expect:[hec]

Incorrect HA MAGIC. FTP64 ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-INCOMPATIBLE_HA_VERSION

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Version. FTP64 ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-INCOMPATIBLE_HA_MSG_LEN

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Message Length. FTP64 ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP64_ALG-3-INVALID_HA_OPCODE

3-Error

rcvd:[hec] expect:[hec]

Invalid HA opcode. FTP64 ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

SCCP_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. SCCP ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

SCCP_ALG-3-INCORRECT_HA_MAGIC

3-Error

rcvd:[hec] expect:[hec]

Incorrect HA MAGIC. SCCP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

SCCP_ALG-3-INCOMPATIBLE_HA_VERSION

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Version. SCCP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

SCCP_ALG-3-INCOMPATIBLE_HA_MSG_LEN

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Message Length. SCCP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

SCCP_ALG-3-INVALID_HA_OPCODE

3-Error

rcvd:[hec] expect:[hec]

Invalid HA opcode. SCCP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. FTP ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-BAD_L7_DATA

3-Error

-

Receive Bad L7 data from either FW or NAT.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-WRITEBACK_ERROR

3-Error

-

Error during writeback.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-INCORRECT_HA_MAGIC

3-Error

rcvd:[hec] expect:[hec]

Incorrect HA MAGIC. FTP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-INCOMPATIBLE_HA_VERSION

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Version. FTP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-INCOMPATIBLE_HA_MSG_LEN

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Message Length. FTP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

FTP_ALG-3-INVALID_HA_OPCODE

3-Error

rcvd:[hec] expect:[hec]

Invalid HA opcode. FTP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. RCMD ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-PKT_MANIP_FAIL

3-Error

-

Packet manipulation failed.Packet will be dropped.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-INCORRECT_HA_MAGIC

3-Error

rcvd:[hec] expect:[hec]

Incorrect HA MAGIC. RCMD ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-INCOMPATIBLE_HA_VERSION

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Version. RCMD ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-INCOMPATIBLE_HA_MSG_LEN

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Message Length. RCMD ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RCMD_ALG-3-INVALID_HA_OPCODE

3-Error

rcvd:[hec] expect:[hec]

Invalid HA opcode. RCMD ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

TFTP_ALG-3-ALG_STATE_CREATE_FAIL

3-Error

-

Get/create ALG state failed. TFTP ALG will not be able to process packets.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. RTSP ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-WRITEBACK_ERROR

3-Error

-

Error during writeback.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-CREATE_CALLBACK_ERROR

3-Error

-

Missing L7 data during imprecise channel creation callback.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-INCORRECT_HA_MAGIC

3-Error

rcvd:[hec] expect:[hec]

Incorrect HA MAGIC. RTSP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-INCOMPATIBLE_HA_VERSION

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Version. RTSP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-INCOMPATIBLE_HA_MSG_LEN

3-Error

rcvd:[hec] expect:[hec]

Incompatible HA Message Length. RTSP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

RTSP_ALG-3-INVALID_HA_OPCODE

3-Error

rcvd:[hec] expect:[hec]

Invalid HA opcode. RTSP ALG will reject sync data.

cpp-ucode

LOG_STD_ACTION

SIP_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. SIP ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

SIP_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

SIP_ALG-3-WRITEBACK_ERROR

3-Error

-

Error during writeback.

cpp-ucode

LOG_STD_ACTION

SIP_ALG-3-CREATE_CALLBACK_ERROR

3-Error

-

Missing L7 data during imprecise channel creation callback.

cpp-ucode

LOG_STD_ACTION

H323_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. H323 ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

H323_ALG-3-CHUNK_MEM_LEAK

3-Error

-

Chunk memory is not being freed by H.323 ALG.

cpp-ucode

LOG_STD_ACTION

SUNRPC_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. Sun RPC ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

SUNRPC_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

MSRPC_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk create failed. MS RPC ALG will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

MSRPC_ALG-3-L7_DATA_CREATE_ERROR

3-Error

-

Error during L7 data creation.

cpp-ucode

LOG_STD_ACTION

SDP-3-CONFIG_PTR_ERROR

3-Error

Received invalid config pointer from application. Unable to process.

The SDP library application has an invalid configuration pointer. The SDP library is therefore unable to handle the request that it received. The configuration of the application will not be as expected and SDP parsing errors may result even for valid SDPs.

voice-sdp

LOG_STD_ACTION

SDP-3-SDP_PTR_ERROR

3-Error

Received invalid SDP pointer from application. Unable to process.

The SDP library application has an invalid SDP pointer. The SDP library is therefore unable to handle the request that it received. SDP parsing or build errors may result.

voice-sdp

LOG_STD_ACTION

SDP-3-INTERNAL

3-Error

[chars]

An internal software error has occurred.

voice-sdp

LOG_STD_SH_TECH_ACTION

ALG_COM-3-ALG_COND_DEBUG_REG_FAILED

3-Error

[chars]

-

-

-

ALG_COM-3-CHUNK_CREATE_FAIL

3-Error

[chars]

A request to create a chunk failed

cpp-ucode

LOG_STD_ACTION

ALG_COM-3-CHUNK_EXTEND_FAIL

3-Error

[chars]

A request to create a chunk failed

cpp-ucode

LOG_STD_ACTION

ALG_COM-3-IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

ALG_COM-3-ALG_REGISTER_FAILED

3-Error

[dec]

ALG registration failed.

cpp-ucode

LOG_STD_ACTION

MCAST-3-MCAST_PA_REPLICATE_FAILED

3-Error

[chars]

m-cast replication failure for PA described packet.

cpp-ucode

LOG_STD_ACTION

MCAST-3-MCAST_REPLICATE_GATHER_FAILED

3-Error

[chars] [inet]

m-cast replication failure due to a bad Multicast Gather parameter.

cpp-ucode

LOG_STD_ACTION

MCAST-3-MCAST_MLRE_ERR

3-Error

Non MLRE friendly FIA on interface [chars]

Unexpected flowlock id following feature execution

cpp-ucode

LOG_STD_ACTION

IPV4MCAST-3-MCAST_CFG_ERR

3-Error

[chars]

Processing MCAST packet failed due to incorrect config to HW Data structures.

cpp-ucode

LOG_STD_ACTION

IPV4MCAST-3-SANITY_CHECK_FAILED

3-Error

PIM register from [inet] for [inet] [inet]

-

-

-

IPV4MCAST-3-MCAST_PA_REPLICATE_FAILED

3-Error

[chars]

m-cast replication failure for PA described packet.

cpp-ucode

LOG_STD_ACTION

IPV4MCAST-3-MCAST_REPLICATE_GATHER_FAILED

3-Error

[chars] [inet]

m-cast replication failure due to a bad Multicast Gather parameter.

cpp-ucode

LOG_STD_ACTION

IPV4MCAST-3-MCAST_MLRE_ERR

3-Error

Non MLRE friendly FIA on interface [chars]

Unexpected flowlock id following feature execution

cpp-ucode

LOG_STD_ACTION

IPV6MCAST-3-MCAST_CFG_ERR

3-Error

[chars]

Processing MCAST packet failed due to incorrect config to HW Data structures.

cpp-ucode

LOG_STD_ACTION

IPV6MCAST-3-SANITY_CHECK_FAILED

3-Error

PIM register from [inet] for [inet] [inet]

-

-

-

IPV6MCAST-3-MCAST_ERR

3-Error

[chars] 0x[hec] 0x[hec] 0x[hec] 0x[hec]

A Mcast replica error has occurred

cpp-ucode

LOG_STD_ACTION

SWITCH_L2M-3-INIT_FAILED

3-Error

Initialization of the SVI feature in QFP failed

Initialization of the SWITCH_L2M feature in the QFP failed. This indicates a software failure.

qfp-switch-infra

LOG_STD_ACTION

SWITCH_L2M-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for SWITCH_L2M feature in QFP

Allocation of memory by the QFP SWITCH_L2M feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

qfp-switch-infra

LOG_STD_ACTION

SWITCH_L2M-3-PKT_REPLICA_INIT_FAILED

3-Error

Failed to register with generic packet replication for SWITCH_L2M feature in QFP

SWITCH_L2M initialization of packet replication registration failed.

qfp-switch-infra

LOG_STD_ACTION

QFP_MLP-2-BQS_SCRATCH_TOOSMALL

2-Critical

QFP BQS Scratch area too small for MLP feature usage size: [dec] need: [dec].

Cisco internal software error. QFP MLP initialization detected that the BQS scratch memory area is insufficient for MLP usage. The MLP Bundle interfaces will not be functional while this condition exists.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP MLP Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP MLP initialization detected that the Proxy IPC interface initialization failed. The MLP Bundle interfaces will not be functional while this condition exists.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-INV_PROXY_MSG

3-Error

QFP MLP Proxy received invalid Message ID [dec]

Cisco internal software error. QFP MLP Proxy received an invalid Message ID. This message will be ignored.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_RX_TX_INTF_VALUE

3-Error

QFP MLP Proxy [chars] [chars] invalid Rx/Tx interface value [dec] for

Cisco internal software error. QFP MLP Proxy was unable to complete the requested MLP Bundle state change or configuration update due to an invalid interface Rx/Tx designation in the proxy request. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_NULL_BUNDLE

3-Error

QFP MLP Proxy [chars] [chars] NULL Bundle sub-block for interface [dec]

Cisco internal software error. QFP MLP Proxy was unable to complete the requested MLP Bundle state change or configuration update due to an invalid or uninitialized Bundle sub-block. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_NULL_LINK

3-Error

QFP MLP Proxy [chars] [chars] NULL Member Link sub-block for

Cisco internal software error. QFP MLP Proxy was unable to complete the requested MLP Member Link state change or configuration update due to an invalid or uninitialized Member Link sub-block. The associated MLP Member Link interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_BUNDLE_STATE

3-Error

QFP MLP Proxy [chars] [chars] invalid Bundle state [chars] [dec] for

Cisco internal software error. QFP MLP Proxy message could not be processed due to the MLP Bundle being in an incorrect state to accept the message. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_LINK_STATE

3-Error

QFP MLP Proxy [chars] [chars] invalid Link state [chars] [dec] for

Cisco internal software error. QFP MLP Proxy message could not be processed due to the MLP Link being in an incorrect state to accept the message. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_SUB_DEV_ID

3-Error

QFP MLP Proxy [chars] [chars] invalid Sub-Device ID [dec] for interface [chars]

Cisco internal software error. QFP MLP Proxy message Bundle Add could not be processed for the indicated interface due to an invalid Sub-Device ID. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_LINK_ID

3-Error

QFP MLP Proxy [chars] [chars] invalid Link ID [dec] for interface [chars]

Cisco internal software error. QFP MLP Proxy message Link Add could not be processed for the indicated interface due to an invalid Link ID. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_DUP_LINK_ID

3-Error

QFP MLP Proxy [chars] [chars] duplicate Link ID [dec] for interface [chars]

Cisco internal software error. QFP MLP Proxy message Link Add could not be processed for the indicated interface due use of a given Link ID on multiple member links within the same MLP Bundle. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_CLASS_INFO

3-Error

QFP MLP Proxy [chars] [chars] invalid Class Info Base: 0x%08x Num: [dec]

Cisco internal software error. QFP MLP Proxy message contained invalid MLP Class information. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_MRRU

3-Error

QFP MLP Proxy [chars] [chars] invalid MRRU [dec] for interface [chars]

Cisco internal software error. QFP MLP Proxy message contained an invalid MLP Bundle MRRU. The associated MLP Bundle interface may not be fully functional as a result of this condition. Possible workaround is to reduce the interface mtu on the Multilink bundle interface on both ends of the connection to 9216 or less and then shut/no shut the Multilink bundle interface to force renegotiation of the MLP MRRU.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_LOST_FRAG_TO

3-Error

QFP MLP Proxy [chars] [chars] indicated an invalid lost fragment

Cisco internal software error. QFP MLP was provided a invalid lost fragment timeout value. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_BUFFER_LIMIT

3-Error

QFP MLP Proxy [chars] [chars] indicated an invalid Rx buffer limit

Cisco internal software error. QFP MLP was provided a invalid Rx buffer limit value. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_TX_LINK_WEIGHT

3-Error

QFP MLP Proxy [chars] [chars] indicated an invalid Tx Link weight

Cisco internal software error. QFP MLP Proxy message contained invalid Tx Link weight information. The associated MLP Member Link and/or Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_INV_TX_LINK_FRAG_SIZE

3-Error

QFP MLP Proxy [chars] [chars] indicated an invalid Tx Link optimal

Cisco internal software error. QFP MLP Proxy message contained invalid Tx Link optimal fragment size information. The associated MLP Member Link and/or Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_B_TX_IDLE_LINK_TRANSITION

3-Error

QFP MLP Proxy [chars] [chars] invalid Bundle state [chars] [dec] for

Cisco internal software error. Multilink Idle-Link transition could not be made due invalid Bundle state at the time of the request. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_LAI_TX_IDLE_LINK_TRANSITION

3-Error

QFP MLP Proxy [chars] [chars] invalid Link state [chars] [dec] for

Cisco internal software error. Multilink Idle-Link transition could not be made due invalid Link state at the time of the request to convert the link to an Idle-Link. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_LIA_TX_IDLE_LINK_TRANSITION

3-Error

QFP MLP Proxy [chars] [chars] invalid Link state [chars] [dec] for

Cisco internal software error. Multilink Idle-Link transition could not be made due invalid Link state at the time of the request to convert the Idle-Link to an active link. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-4-PROXY_SYNC

4-Warning

QFP MLP Proxy [chars] [chars] Bundle/Link sync issue with interface [chars]

Cisco internal software error. QFP MLP Proxy message processing detected a Bundle-Link state synchronization abnormality. This condition should be cosmetic. Full context of the message will aid in problem isolation.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_IPC_ALLOC_FAIL

3-Error

QFP MLP Proxy [chars] response lost due to buffer allocation

Cisco internal software error. QFP MLP Proxy message processing detected a IPC buffer allocation failure during response processing. The associated MLP interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-4-PROXY_IPC_ALLOC_FAIL2

4-Warning

QFP MLP Proxy [chars] response lost due to buffer allocation

Cisco internal software error. QFP MLP Proxy message processing detected a IPC buffer allocation failure during proxy response processing. The associated MLP functionality may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_SID_UPDATE_LOCK_ERROR

3-Error

QFP MLP Proxy [chars] Multiple SID Update Locks to same interface

Cisco internal software error. QFP MLP Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-PROXY_SID_UPDATE_COMPLETE_ERROR

3-Error

QFP MLP Proxy [chars] SID Update Complete w/o Preceeding Lock

Cisco internal software error. QFP MLP Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-EARLY_RX_INIT

3-Error

QFP MLP Early Receive initialization error [chars]

Cisco internal software error. Multilink Early Receive initialization could not be performed due to indicated error. This could cause possible lost MLP encapsulated packets during member link/bundle bringup and possibly cause the failure to complete member link/bundle initialization.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-EARLY_RX_CLEANUP

3-Error

QFP MLP Early Receive cleanup error [chars]

Cisco internal software error. Multilink Early Receive cleanup could not be performed due to indicated error. This could cause possible QFP memory leak.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-MCMP_TX_ENCAP_SEQ_CFG_ERROR

3-Error

MLP QoS encap-sequence [dec] must be less than the number

User software configuration mismatch with PPP Multilink Multiclass MCMP. User needs to either reduce the highest encap-sequence in

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-MCMP_INVALID_RX_CLASS

3-Error

MLP MCMP suspension class ID [dec] received from the peer

Possible error on the peer device with PPP Multilink Multiclass MCMP. Received MLP packet contained a MCMP suspension class ID

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-4-TX_BUNDLE_FLOWED_OFF

4-Warning

QFP MLP Tx Bundle [chars] flowed OFF for an abnormal duration due to one or more congested member links Ticks: [dec]

Possible Cisco internal software or hardware error. QFP MLP Tx processing detected that a MLP Bundle interface was flowed off for an extended period of time due to a congested member link queue. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-4-TX_BUNDLE_FLOWED_ON

4-Warning

QFP MLP Tx Bundle [chars] flowed ON after being flowed OFF for an abnormal duration Ticks: [dec]

Possible Cisco internal software or hardware error. QFP MLP Tx processing detected that a MLP Bundle interface was flowed off for an extended period of time due to a congested member link queue. The associated MLP Bundle interface may not be fully functional as a result of this condition.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-3-MLP_INVALID_EVSI_INTF_STATE

3-Error

MLP Link Add/Update receved with invalid EVSI indication for Member Link: [chars] Bundle: [chars]

Either the user attempted to mix broadband and non-broadband member links on the same bundle or an internal error has occurred processing a configuration update.

qfp-mlppp keyword:none

LOG_STD_ACTION

QFP_MLP-4-TX_BUNDLE_LOOP

4-Warning

QFP detected re-entry into MLP Tx Bundle [chars].

-

-

-

IPV4_FORWARDING-2-CAUSE_THROTTLE_ERR

2-Critical

Allocation of ipv4 throttle [chars] memory failed

Allocation of memory resource use by ipv4 throttle fail

cpp-ucode

LOG_STD_ACTION

IPV4_FORWARDING-3-CAUSE_LINKTYPE_ERR

3-Error

Unsupported link type - linktype = [dec] dropping packet

Link type is unsupported at the current time.

cpp-ucode

LOG_STD_ACTION

IPV4_FORWARDING-4-CHECKSUM_ERR

4-Warning

Checksum buffer walk failed

Internal problem occured during calculating segmented packet checksum.

cpp-ucode

LOG_STD_ACTION

IPV4_FORWARDING-3-TABLE_ID_SZ_ERR

3-Error

Table ID size configured incorrectly: [dec]

Table ID size must be less than or equal to 16 or 32 bits.

cpp-ucode

LOG_STD_ACTION

IPV4_FORWARDING-3-TRAFFIC_IDX_ERR

3-Error

Traffic index invalid value: [dec] Buckets allocated: [dec]

Traffic index is greater than or equal to the buckets allocated

cpp-ucode

LOG_STD_ACTION

IPV4_VFR-4-TINY_FRAGMENTS

4-Warning

Dropping [chars] from [chars] due to tiny fragment.

This message indicates that the router is receiving tiny fragments - meaning the initial fragment does not have complete layer 4 header

qfp-ipucast

"This is an informational message"

IPV4_VFR-4-OVERLAP_FRAGMENTS

4-Warning

Dropping [chars] from [chars] due to overlap fragment.

This message is logged whenever the router encounters overlap fragments. Overlap fragment means offset of one fragment overlaps the offset of another fragment. For example if first fragment's offset is 0 and length is 800 then the second fragments offset must be 800. If second fragment's offset is less than 800 that means the second fragment overlaps the first fragment.

qfp-ipucast

"This could possibly be an attack configure a static ACL to prevent " "further overlap fragments from the sender"

IPV4_VFR-4-FRAG_TABLE_OVERFLOW

4-Warning

Dropping [chars] from [chars] due to fragment table overflow.

This means the number of datagrams reassembled at a time reached its maximum limit increase the value of max-reassemblies using ip virtual-reassembly max-reassemblies <number>

qfp-ipucast

-

IPV4_VFR-4-TOO_MANY_FRAGMENTS

4-Warning

Dropping [chars] from [chars] due to too many fragments for the datagram.

This message indicates the datagram being reassembled has received more fragments than its threshold value

qfp-ipucast

"Check if the fragments received are from a genuine source if so " "increase the value of max-fragments using the CLI " "ip virtual-reassembly max-fragments <number>"

IPV4_VFR-4-INVALID_FRAG_LENGTH

4-Warning

Dropping [chars] from [chars] due to invalid fragment length.

This message indicates that the router has encountered a fragment with invalid packet length

qfp-ipucast

"To prevent further attacks its highly recommended that an ACL " "be configured to drop any traffic from the sender"

IPV4_VFR-4-TIMEOUT

4-Warning

Dropping [chars] from [chars] due to virtual reassembly timeout.

This message indicates that the router is trying to do virtual-reassembly for fragments but got timeout before receiving all the fragments for a datagram

qfp-ipucast

"This is an informational message"

IPV4_VFR-4-CONFIG

4-Warning

Dropping [chars] from [chars] due to system config.

This message indicates that the router drops fragment packet due to ip virtual-reassembly drop-fragments

qfp-ipucast

"This is an informational message"

IPV4_VFR-4-INVALID_DROP_LOG_TYPE

4-Warning

Dropping [chars] from [chars]. Invalid drop log type [dec]

Unsupported drop log type

qfp-ipucast

LOG_STD_ACTION

ERSPAN-3-MEM_INIT_FAILED

3-Error

Allocation of [chars] memory failed for ERSPAN

ERSPAN Initialization of channel pool failed.

cpp-ucode

LOG_STD_ACTION

ERSPAN-3-PKT_REPLICA_INIT_FAILED

3-Error

Register to Generic Packet Replication failed for ERSPAN

ERSPAN Initialization of packet replication registration failed.

cpp-ucode

LOG_STD_ACTION

EPC-3-MEM_INIT_FAILED

3-Error

Allocation of [chars] memory failed for EPC

EPC Initialization of channel pool failed.

cpp-ucode

LOG_STD_ACTION

EPC-3-PKT_REPLICA_INIT_FAILED

3-Error

Register to Generic Packet Replication failed for EPC

EPC Initialization of packet replication registration failed.

cpp-ucode

LOG_STD_ACTION

SERVICE_CONTROLLER-3-HA_INVALID_STATE

3-Error

state [dec]

An invalid HA state was received from the HA infrastructure.

service-controller

LOG_STD_ACTION

SERVICE_CONTROLLER-3-HA_BULK_SYNC_FAIL

3-Error

rg [dec]

There was a failure such that service controller bulk sync did not occur

service-controller

LOG_STD_ACTION

CFT-3-HA_INVALID_RG_RCVD

3-Error

invalid [chars] opcode [chars] [dec] - rg [dec]:[dec]

Standby received an invalid Redundancy group

cpp-ucode

LOG_STD_ACTION

CFT-3-HA_INVALID_MSG_RCVD

3-Error

invalid [chars] [hec] opcode [chars] [hec]

Standby received an invalid Firewall HA message

cpp-ucode

LOG_STD_ACTION

CFT-3-HA_INVALID_MSG_LEN_RCVD

3-Error

invalid [chars] rg [dec] [dec] expected [dec] opcode [chars] [hec]

Standby received an invalid Firewall HA message

cpp-ucode

LOG_STD_ACTION

CFT-3-HA_INVALID_MSG_NO_V6KEY_RCVD

3-Error

Missing IPv6 key - rg: [dec] len: [dec] msg type: \[chars]\ [hec] flow type: [dec]

Standby received an invalid Firewall HA message

cpp-ucode

LOG_STD_ACTION

CFT-3-HA_INVALID_MSG_VRF_HASH

3-Error

rg: [dec] i_vrf_hash: 0x%llx r_vrf_hash: 0x%llx

Standby received an unrecognized VRF name hash

cpp-ucode

LOG_STD_ACTION

CFT-3-HA_INVALID_BULK_SYNC

3-Error

Invalid message length for bulk sync got [dec] expected [dec]

Standby received an unrecognized VRF name hash

cpp-ucode

LOG_STD_ACTION

CFT-3-HA_INVALID_ID_BULK_SYNC

3-Error

Invalid feature id for bulk sync got [dec] expected [dec]

Standby received an unrecognized VRF name hash

cpp-ucode

LOG_STD_ACTION

DPSS-3-MEM_INIT_FAILED

3-Error

Allocation of [chars] memory failed for DPSS

DPSS Initialization of channel pool failed.

cpp-ucode

LOG_STD_ACTION

DPSS-3-PKT_REPLICA_INIT_FAILED

3-Error

Register to Generic Packet Replication failed for DPSS

DPSS Initialization of packet replication registration failed.

cpp-ucode

LOG_STD_ACTION

DPSS-3-DPSS_INIT_FAILED

3-Error

DPSS [chars] Register failed

DPSS Initialization of registration failed.

cpp-ucode

LOG_STD_ACTION

UTD-3-UTD_COND_DEBUG_REG_FAILED

3-Error

Failed to initialize Conditional Debugging for UTD

A non-fatal error occurred when attempting to Register/Initialize\n conditional debugging.

qfp-ucode

LOG_STD_ACTION

UTD-5-UTD_POLICY_NAT_DROP_PKT

5-Notice

NAT packet drop

Packet dropped by NAT during UTD policy phase\n

qfp-ucode

LOG_STD_ACTION

UTD-5-UTD_POLICY_DROP_PKT

5-Notice

Policy: Dropped packet from vrf [chars] [chars] [inet]:[dec] => [inet]:[dec] proto [chars] due to [dec] [chars] ident [dec] [chars]

-

-

-

UTD-4-UTD_INSPECT_DROP_PKT

4-Warning

Inspection: Dropped packet from vrf [chars] [chars] [inet]:[dec] => [inet]:[dec] proto [chars] due to [dec] [chars] ident [dec] [chars]

-

-

-

UTD-4-UTD_DIVERT_DROP_PKT

4-Warning

Diversion: VPATH decapsulation dropped packet from vrf [chars] [chars] [inet]:[dec] => [inet]:[dec] proto [chars] due to [dec] [chars] ident [dec] [chars]

-

-

-

UTD-4-UTD_ENCAPS_DROP_PKT

4-Warning

Diversion: VPATH encapsulation dropped packet from vrf [chars] [chars] [inet]:[dec] => [inet]:[dec] proto [chars] due to [dec] [chars] ident [dec] [chars]

-

-

-

UTD-1-UTD_HEALTH_CHANGE

1-Alert

Service node changed state [chars] => [chars] [dec]

Service node and changed health status\n

cpp-ucode

LOG_STD_ACTION

UTD-6-UTD_DF_WHITELIST_MATCH

6-Information

UTD WebFilter Domain Whitelist [**] [Domain: [chars]] [Matched Pattern: [chars]] {[chars]} [inet]:[dec] -> [inet]:[dec]

DNS domain matched to one of the configured whitelist patterns\n

cpp-ucode

LOG_STD_NO_ACTION

UTD-6-UTD_DF_BLACKLIST_MATCH

6-Information

UTD WebFilter Domain Blacklist [**] [Domain: [chars]] [Matched Pattern: [chars]] {[chars]} [inet]:[dec] -> [inet]:[dec]

DNS domain matched to one of the configured blacklist patterns\n

cpp-ucode

LOG_STD_NO_ACTION

UTD-3-UTD_TLS_POLICY_CLASSIFY_PKT_FAIL

3-Error

UTD TLS policy classify packet fail

Failed to classify packet according to UTD TLS policy\n

cpp-ucode

"1 Run the following command and see if TCAM memory utilization is full\n"

PBR-3-PBR_CLASSIFY_FAIL

3-Error

Dataplane classification error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of a route map due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:pbr

LOG_STD_ACTION

FHS-3-FHS_CLASSIFY_FAIL

3-Error

Dataplane FHS classification error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of FHS Snoop due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:fhs

LOG_STD_ACTION

FHS-3-FHS_MISS_ACTION_FAIL

3-Error

Dataplane FHS miss action error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of FHS Snoop due to a invalid miss action. This is likely due to a data initialization error

cpp-ucode keyword:fhs

LOG_STD_ACTION

FHS-3-FHS_FILTER_FAIL

3-Error

Dataplane FHS filter error for interface [chars]

Cisco internal software error. The FHS pktsb shouldn't be set in use before. This is likely due to a data initialization error

cpp-ucode keyword:fhs

LOG_STD_ACTION

FHS-3-FHS_INIT_FAIL

3-Error

Dataplane FHS init error for [chars]

Cisco internal software error. This is likely due to a dataplane memory exhaust

cpp-ucode keyword:fhs

LOG_STD_ACTION

SERVICE_CHAIN-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for Service Chaining feature

Allocation of memory by the Service Chaining feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

iosxe-servicechain

LOG_STD_ACTION

SERVICE_CHAIN-3-PKT_REPLICA_INIT_FAILED

3-Error

Failed to register with generic packet replication for Service Chaining feature

Service Chaining initialization of packet replication registration failed.

iosxe-servicechain

LOG_STD_ACTION

CWS-5-CWS_ON_PATH_DEBUG

5-Notice

NSH D-bit set for SIP: [inet] DIP: [inet] Src_node: [dec] Src_If_Id: [dec] Tenant_Id: [dec]

CTR has seen an NSH header with D-bit set\n

-

LOG_STD_NO_ACTION

CWS-5-CWS_INVALID_REF_COUNT

5-Notice

Invalid ref count [dec] in chunk [hex]

CTR has seen an invalid ref count in the NSH pool\n

cpp-ucode

LOG_STD_NO_ACTION

ETHERNET-3-ETHERNET_INIT_FAIL

3-Error

Dataplane ETHERNET init error for [chars]

Cisco internal software error. This is likely due to a dataplane memory exhaust

cpp-ucode keyword:ethernet

LOG_STD_ACTION

LI-3-MEM_INIT_FAILED

3-Error

Allocation of [chars] memory failed for LI

LI Initialization of channel pool failed.

cpp-ucode

LOG_STD_ACTION

LI-3-PKT_REPLICA_INIT_FAILED

3-Error

Register to Generic Packet Replication failed for LI

LI Initialization of packet replication registration failed.

cpp-ucode

LOG_STD_ACTION

SDVT-3-SDVT_COND_DEBUG_REG_FAILED

3-Error

Failed to initialize Conditional Debugging for SDVT

A non-fatal error occurred when attempting to Register/Initialize\n conditional debugging.

qfp-ucode

LOG_STD_ACTION

SDVT-2-SDVT_HEALTH_CHANGE

2-Critical

Service node %Ci changed state from [chars] => [chars] [dec] for channel [chars]

Service node has changed health status\n

cpp-ucode

LOG_STD_ACTION

SDVT-2-SDVT_HEALTH_DOWN

2-Critical

Service node %Ci is down for channel [chars]. Current Health: [chars] Previous Health: [chars]

Service node has changed status to Down\n

cpp-ucode

LOG_STD_ACTION

SDVT-5-SDVT_HEALTH_UP

5-Notice

Service node %Ci is up for channel [chars]. Current Health: [chars] Previous Health: [chars]

Service node has changed status to Green\n

cpp-ucode

LOG_STD_ACTION

ETHERCHANNEL-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP Etherchannel Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP Etherchannel initialization detected that the Proxy IPC interface initialization failed. The EC Bundle interfaces will not be functional while this condition exists.

qfp-ethernet keyword:gec

LOG_STD_ACTION

ETHERCHANNEL-3-INV_PROXY_MSG

3-Error

QFP ETHERCHANNEL Proxy received invalid Message ID [dec]

Cisco internal software error. QFP Etherchannel Proxy received an invalid Message ID. This message will be ignored.

qfp-ethernet keyword:gec

LOG_STD_ACTION

ETHERCHANNEL-3-PROXY_IPC_ALLOC_FAIL

3-Error

QFP ETHERCHANNEL Proxy [chars] response lost due to buffer allocation

Cisco internal software error. QFP ETHERCHANNEL Proxy message processing detected a IPC buffer allocation failure during response processing. The associated ETHERCHANNEL interface may not be fully functional as a result of this condition.

qfp-ethernet keyword:gec

LOG_STD_ACTION

ETHERCHANNEL-3-PROXY_SID_UPDATE_LOCK_ERROR

3-Error

QFP EC Proxy [chars] Multiple SID Update Locks to same interface

Cisco internal software error. QFP EC Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected.

qfp-ethernet keyword:gec

LOG_STD_ACTION

ETHERCHANNEL-3-PROXY_SID_UPDATE_COMPLETE_ERROR

3-Error

QFP EC Proxy [chars] SID Update Complete w/o Preceeding Lock

Cisco internal software error. QFP EC Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected.

qfp-ethernet keyword:gec

LOG_STD_ACTION

ETHERCHANNEL-3-LOCK_ERROR

3-Error

QFP EC Lock Failure: retval:[dec] tries[dec]

Cisco internal software error. QFP EC Lock Failure locking attempt failed

qfp-ethernet keyword:gec

LOG_STD_ACTION

ETHERCHANNEL-3-LOCK_STATE_ERROR

3-Error

QFP EC Lock State Failure: retval:[dec]

Cisco internal software error. QFP EC Lock State Failure Illegal lock state

qfp-ethernet keyword:gec

LOG_STD_ACTION

ACL-3-UNEXPECTED_STATE

3-Error

type [dec] int [chars] [chars]put w0: 0x%p w1: 0x[hec]

An error has occurred in the setup of ACL hardware.

cpp-ucode

LOG_STD_ACTION

ACL-3-UNEXPECTED_PKT_TYPE

3-Error

type [dec] int [dec] [chars]put

ACL logging has encountered unexpected pkt type.

cpp-ucode

LOG_STD_ACTION

L4-3-HA_INVALID_MSG_RCVD

3-Error

invalid [chars] [hec] expected [hec] opcode [chars] [hec]

Standby received an invalid Layer 4 HA message

cpp-ucode

LOG_STD_ACTION

L4-3-HA_INVALID_MSG_LEN_RCVD

3-Error

invalid [chars] rg [dec] [dec] expected [dec] opcode [chars] [hec]

Standby received an invalid Firewall HA message

cpp-ucode

LOG_STD_ACTION

FW-4-ALERT_ON

4-Warning

target:class-[chars]:[chars]:[chars] count [dec]/[dec] current rate: [dec] [chars]

Either the max-incomplete high threshold of half-open connections \n or the new connection initiation rate has been exceeded. This error \n message indicates that an unusually high rate of new connections is \n coming through the firewall and a DOS attack may be in progress. \n This message is issued only when the max-incomplete high threshold \n is crossed.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

FW-4-ALERT_OFF

4-Warning

target:class-[chars]:[chars]:[chars] count [dec]/[dec] current rate: [dec] [chars]

Either the number of half-open connections or the new connection \n initiation rate has gone below the max-incomplete low threshold. \n This message indicates that the rate of incoming new connections \n has slowed down and is issued only when the max-incomplete low \n threshold is crossed.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" that an attack has stopped."

FW-4-HOST_TCP_ALERT_ON

4-Warning

target:class-[chars]:[chars]:Max tcp half-open connections [dec] exceeded for host [inet][chars]. [chars]

-

-

-

FW-2-BLOCK_HOST

2-Critical

target:class-[chars]:[chars]:Blocking new TCP connections to host [inet] for [dec] minute[chars] half-open count [dec] exceeded. [chars]

This message indicates that any subsequent new TCP connection \n attempts to the specified host will be denied because the \n max-incomplete host threshold of half-open TCP connections is \n exceeded and the blocking option is configured to block the \n subsequent new connections. The blocking will be removed when the \n configured block-time expires.

cpp-ucode

"This message is for informational purposes only but may indicate \n"" that a SYN flood attack was attempted."

FW-4-UNBLOCK_HOST

4-Warning

target:class-[chars]:[chars]:New TCP connections to host [inet][chars] no longer blocked [chars]

New TCP connection attempts to the specified host are no longer \n blocked. This message indicates that the blocking of new TCP \n attempts to the specified host has been lifted.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a SYN flood attack was attempted to the host."

FW-6-SESS_AUDIT_TRAIL_START

6-Information

target:class-[chars]:[chars]:Start [chars] session: initiator [inet][chars]:[dec]

This message documents the opening of an inspection session.\n The message is issued at the start of each inspected session\n and it records the source/destination addresses and ports.

cpp-ucode

"This message is for informational purposed only and can be used \n"" to collect the basic accounting for inspected sessions."

FW-6-SESS_AUDIT_TRAIL

6-Information

target:class-[chars]:[chars]:Stop [chars] session: initiator [inet][chars]:[dec]

This message documents the per-session transaction log of network \n activities. The message is issued at the end of each inspected \n session and it records the source/destination addresses and ports \n as well as the number of bytes transmitted by the client and \n server.

cpp-ucode

"This message is for informational purposed only and can be used \n"" to collect the basic accounting for the inspected sessions."

FW-6-LOG_SUMMARY

6-Information

[dec] [chars] packet[chars] [chars] from [chars] [inet][chars]:[dec] => [inet][chars]:[dec] target:class-[chars]:[chars] [chars] [chars]

-

-

-

FW-6-PASS_PKT

6-Information

Passing [chars] pkt from [chars] [inet][chars]:[dec] => [inet][chars]:[dec] target:class-[chars]:[chars] [chars] [chars] with ip ident [dec] [chars]

-

-

-

FW-6-DROP_PKT

6-Information

Dropping [chars][chars] pkt from [chars] [inet][chars]:[dec] => [inet][chars]:[dec] target:class-[chars]:[chars] [chars] [chars] with ip ident [dec] [chars] [chars] [chars] [chars] [chars]

-

-

-

FW-4-SESSIONS_MAXIMUM

4-Warning

Number of sessions for the firewall policy on target:class-[chars]:[chars] exceeds

This message indicates that the number of established ZBF\n sessions have crossed the configured sessions maximum limit

cpp-ucode

"This message is for informational purpose only but may indicate\n"" a security problem. This might also mean that the sessions maximum \n"" is set to a low value in which case the sessions maximum value could be\n"" increased through paramter-map type inspect CLI"

FWALL-3-HA_INVALID_MSG_RCVD

3-Error

invalid [chars] [hec] expected [hec] opcode [chars] [hec]

Standby received an invalid Firewall HA message

cpp-ucode

LOG_STD_ACTION

FWALL-3-HA_INVALID_STATE

3-Error

[dec]

Invalid state

cpp-ucode

LOG_STD_ACTION

FWALL-3-FW_ALG_INVALID_TYPE

3-Error

[chars] [dec]:[dec]

Invalid alg type passed from alg to firewall

cpp-ucode

LOG_STD_ACTION

FWALL-3-FW_NO_STATS

3-Error

[dec]:[dec] zone pair [chars] class [chars]

Client has not provided stats for the given protocol:applicaton id

cpp-ucode

LOG_STD_ACTION

FWALL-3-FW_NO_MATCH_INDEX_STATS

3-Error

[dec]---[dec]

Client has not provided stats for the given match_index

cpp-ucode

LOG_STD_ACTION

FWALL-7-FW_NO_DROP_CAUSE

7-Debug

[dec]

Unsupported drop cause

cpp-ucode

LOG_STD_ACTION

FWALL-7-FW_NO_ALERT_CAUSE

7-Debug

[dec]

Unsupported alert cause

cpp-ucode

LOG_STD_ACTION

FW-4-HALFOPEN_LIMIT_EXCEEDED

4-Warning

[chars] half open session limit exceeded. configured limit [dec] [chars]

The halfopen session limit of a specific layer 4 protocol or the total \n halfopen session limit exceeded. \n This error message indicates that an unusually high rate of new \n connections is coming through the firewall and a DOS attack may be in \n progress. \n This message is issued only when the max-incomplete high threshold \n is crossed.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

FW-4-VRF_HALFOPEN_LIMIT_EXCEEDED

4-Warning

VRF id [dec] [chars] half open session limit exceeded. configured limit [dec] [chars]

The halfopen session limit of a specific layer 4 protocol or the total \n halfopen session limit exceeded for a specific vrf id. \n This error message indicates that an unusually high rate of new \n connections is coming through the firewall and a DOS attack may be in \n progress. \n This message is issued only when the max-incomplete high threshold \n is crossed.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

FW-4-AGG_AGE_PERIOD_ON

4-Warning

[chars] session count has exceeded the aggressive aging high watermark [dec] [chars]

Start aggressive aging period. The aggressive aging high threshold \n of per-box halfopen or total sessions has been exceeded. \n This message indicates that a DOS attack may be in progress hence \n aggressive aging feature will take affect. The feature protects \n the firewall sessions resources by allowing idle sessions to be \n exist for a shorter period of time.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

FW-4-VRF_AGG_AGE_PERIOD_ON

4-Warning

[chars] session count of VRF id [dec] has exceeded the aggressive aging high watermark [dec] [chars]

Start aggressive aging period for VRF. The aggressive aging high \n threshold of VRF halfopen or total sessions has been exceeded. \n This message indicates that a DOS attack may be in progress hence \n aggressive aging feature will take affect. The feature protects \n the firewall sessions resources by allowing idle sessions to be \n exist for a shorter period of time.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

FW-4-AGG_AGE_PERIOD_OFF

4-Warning

[chars] session count has dipped below the aggressive aging low watermark [dec] [chars]

The number of per-box half-open or total sessions has gone \n below the aggressive aging low threshold. This message indicates \n end of aggressive aging period.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

FW-4-VRF_AGG_AGE_PERIOD_OFF

4-Warning

[chars] session count of VRF id [dec] has dipped below the aggressive aging low watermark [dec] [chars]

The number of VRF half-open or total sessions has gone \n below the aggressive aging low threshold. This message indicates \n end of aggressive aging period.

cpp-ucode

"This message is for informational purposed only but may indicate \n"" a security problem."

CAPWAP_FRAG-3-INIT_FAILED

3-Error

Initialization of the CAPWAP_FRAG feature in QFP failed

Initialization of the CAPWAP_FRAG feature in the QFP failed. This indicates a software failure.

qfp

LOG_STD_ACTION

CAPWAP_FRAG-3-CAPWAP_FRAG_ERR

3-Error

Capwap Fragmentation encountered an error: [chars]

Capwap Fragmentation encountered a runtime error as indicated

qfp

LOG_STD_ACTION

CAPWAP_FRAG-3-CAPWAP_FRAG_DBG

3-Error

Capwap Fragmentation encountered an error: [chars] [chars] %lu [chars] %lu

Capwap Fragmentation encountered a runtime error as indicated in the message with parameter data for debug

qfp

LOG_STD_ACTION

CAPWAP_FRAG-2-UNENABLED

2-Critical

[chars] feature not enabled at interface [chars] packet cannot be processed

Capwap Fragmentation feature as indicated not enabled by the control plane. This is a critical problem.

qfp

LOG_STD_ACTION

CAPWAP_FRAG-3-INVALID_QFP_NO

3-Error

Invalid qfp device no.: [chars]

Invalid qfp device no.

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-INIT_FAILED

3-Error

Initialization of the CAPWAP_REASS feature in QFP failed

Initialization of the CAPWAP_REASS feature in the QFP failed. This indicates a software failure.

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for CAPWAP_REASS feature in QFP

Allocation of memory by the QFP CAPWAP_REASS feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-MEM_REQ_FAILED

3-Error

-

IPC Failure occurred when attempting to request more capwap reass pool memory.

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-MEM_INIT_FAILED

3-Error

-

Failure occurred initializing capwap reass memory pool.

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-CAPWAP_REASS_ERR

3-Error

Capwap Reassembly encountered an error: [chars]

Capwap Reassembly encountered a runtime error as indicated

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-CAPWAP_REASS_DBG

3-Error

Capwap Reassembly encountered an error: [chars] [chars] %lu [chars] %lu

Capwap Reassembly encountered a runtime error as indicated in the message with parameter data for debug

qfp

LOG_STD_ACTION

CAPWAP_REASS-2-UNENABLED

2-Critical

[chars] feature not enabled at interface [chars] packet cannot be processed

Capwap Reassembly feature as indicated not enabled by the control plane. This is a critical problem.

qfp

LOG_STD_ACTION

CAPWAP_REASS-3-INVALID_QFP_NO

3-Error

Invalid qfp device no.: [chars]

Invalid qfp device no.

qfp

LOG_STD_ACTION

PW-3-IPC_ALLOC_FAILED

3-Error

[chars]

Allocation of an IPC packet buffer by the pseudo wired feature failed.

cpp-ucode

LOG_STD_ACTION

PW-3-IPC_SEND_FAILED

3-Error

[chars]

Transmission of an IPC message by the pseudo wire feature failed.

cpp-ucode

LOG_STD_ACTION

VPLS-3-INVALID_ENCAP

3-Error

[chars]: [chars] mpls label: [dec]

Invalid encap type for VPLS processed packet.

cpp-ucode

LOG_STD_ACTION

FME_DP-3-DEBUG_REG_FAILED

3-Error

Flow Metric Engine fails to registrate with Conditional Debugging.

Flow Metric Engine fails to registrate with Conditional Debugging infra.

asr1k-avc

LOG_STD_ACTION

MMA_DP-3-DEBUG_REG_FAILED

3-Error

Metric Mediation Agent fails to registrate with Conditional Debugging.

Metric Mediation Agent fails to registrate with Conditional Debugging infra.

asr1k-avc

LOG_STD_ACTION

SWPORT-3-INIT_FAILED

3-Error

Initialization of the SWPORT feature in QFP failed

Initialization of the SWPORT feature in the QFP failed. This indicates a software failure.

qfp-swport

LOG_STD_ACTION

SWPORT-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for SWPORT feature in QFP

Allocation of memory by the QFP SWPORT feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

qfp-swport

LOG_STD_ACTION

SWPORT-4-MAC_CONFLICT

4-Warning

Dynamic mac %04X.%04X.%04X from [chars] conflict with [chars] please check the network topology and make sure there is no loop.

When eWLC receives a packet whose src MAC in the outer ethernet header \n is eWLC SVI's MAC or is a wireless client's MAC this warning message \n is printed

qfp-swport

"In most cases this warning message indicates a L2 loop connection \n" "in the network please check the network topology and make sure \n" "there is no loop"

CPP_FR-2-PROXY_IPC_INIT_FAILED

2-Critical

Frame Relay Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. FR initialization detected that the Proxy IPC interface initialization failed. The FR interfaces may not function properly while this condition exists.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-INV_PROXY_MSG

3-Error

CPP FR Proxy received invalid IPC message ID [dec]

Cisco internal software error. CPP FR Proxy received an invalid message ID. This message will be ignored.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_IPC_ALLOC_FAIL

3-Error

CPP Frame Relay Proxy response to msg id [dec] lost due to buffer allocation failure

Cisco internal software error. CPP Frame Relay Proxy message processing detected a IPC buffer allocation failure during response processing.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-4-PROXY_IPC_ALLOC_FAIL2

4-Warning

QFP Frame Relay MFR Proxy [chars] response lost due to buffer allocation

Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a IPC buffer allocation failure during proxy response processing. The associated Frame Relay MFR functionality may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_SID_UPDATE_LOCK_ERROR

3-Error

QFP Frame Relay Proxy [chars] Multiple SID Update Locks to same interface

Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected.

cpp-ucode keyword:frame_relay

LOG_STD_ACTION

CPP_FR-3-PROXY_SID_UPDATE_COMPLETE_ERROR

3-Error

QFP Frame Relay MFR Proxy [chars] SID Update Complete w/o Preceeding Lock

Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected.

cpp-ucode keyword:frame-realy

LOG_STD_ACTION

CPP_FR-2-BQS_SCRATCH_TOOSMALL

2-Critical

QFP BQS Scratch area too small for Frame Relay MFR feature usage size: [dec] need: [dec].

Cisco internal software error. QFP Frame Relay MFR initialization detected that the BQS scratch memory area is insufficient for Frame Relay MFR usage. The Frame Relay MFR Bundle interfaces will not be functional while this condition exists.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_RX_TX_INTF_VALUE

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] invalid Rx/Tx interface value [dec] for

Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Bundle state change or configuration update due to an invalid interface Rx/Tx designation in the proxy request. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_NULL_BUNDLE

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] NULL Bundle sub-block for

Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Bundle state change or configuration update due to an invalid or uninitialized Bundle sub-block. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_NULL_LINK

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] NULL Member Link sub-block for

Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Member Link state change or configuration update due to an invalid or uninitialized Member Link sub-block. The associated Frame Relay MFR Member Link interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_NULL_DLCI

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] NULL PVC sub-block for

Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Member PVC state change or configuration update due to an invalid or uninitialized PVC sub-block. The associated Frame Relay MFR PVC interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_BUNDLE_STATE

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] invalid Bundle state [chars] [dec] for

Cisco internal software error. QFP Frame Relay MFR Proxy message could not be processed due to the Frame Relay MFR Bundle being in an incorrect state to accept the message. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_LINK_STATE

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] invalid Link state [chars] [dec] for

Cisco internal software error. QFP Frame Relay MFR Proxy message could not be processed due to the Frame Relay MFR Link being in an incorrect state to accept the message. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_SUB_DEV_ID

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] invalid Sub-Device ID [dec] for interface [chars]

Cisco internal software error. QFP Frame Relay MFR Proxy message Bundle Add could not be processed for the indicated interface due to an invalid Sub-Device ID. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-mlppp keyword:none

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_LINK_ID

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] invalid Link ID [dec] for interface [chars]

Cisco internal software error. QFP Frame Relay MFR Proxy message Link Add could not be processed for the indicated interface due to an invalid Link ID. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_DUP_LINK_ID

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] duplicate Link ID [dec] for interface [chars]

Cisco internal software error. QFP Frame Relay MFR Proxy message Link Add could not be processed for the indicated interface due use of a given Link ID on multiple member links within the same Frame Relay MFR Bundle. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_DLCI_INFO

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] invalid PVC Info Base: 0x%08x Num: [dec]

Cisco internal software error. QFP Frame Relay MFR Proxy message contained invalid Frame Relay MFR PVC information. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_DUP_DLCI_ID

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] duplicate DLCI [dec] for interface [chars]

Cisco internal software error. QFP Frame Relay MFR Proxy message DLCI Add could not be processed for the indicated interface due use of a given DLCI on multiple member links within the same Frame Relay MFR Bundle. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_LOST_SEQ_TO

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] indicated an invalid lost sequence

Cisco internal software error. QFP Frame Relay MFR was provided a invalid lost sequence timeout value. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_BUFFER_LIMIT

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] indicated an invalid Rx buffer limit

Cisco internal software error. QFP Frame Relay MFR was provided a invalid Rx buffer limit value. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-PROXY_INV_TX_LINK_WEIGHT

3-Error

QFP Frame Relay MFR Proxy [chars] [chars] indicated an invalid Tx Link weight

Cisco internal software error. QFP Frame Relay MFR Proxy message contained invalid Tx Link weight information. The associated Frame Relay MFR Member Link and/or Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-4-PROXY_SYNC

4-Warning

QFP Frame Relay MFR Proxy [chars] [chars] Bundle/Link sync issue with interface [chars]

Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a Bundle-Link state synchronization abnormality. This condition should be cosmetic. Full context of the message will aid in problem isolation.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-3-MFR_INVALID_RX_DLCI

3-Error

Frame Relay MFR DLCI [dec] received from the peer

Possible error on the peer device with Multilink FR. Received Multilink FR packet contained wrond DLCI number.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CPP_FR-4-TX_BUNDLE_FLOWED_OFF

4-Warning

QFP Frame Relay MFR Tx Bundle [chars] flowed off for an abnormal duration due to one or more congested member links

Possible Cisco internal software or hardware error. QFP Frame Relay MFR Tx processing detected that a Frame Relay MFR Bundle interface was flowed off for an extended period of time due to a congested member link queue. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition.

cpp-ucode keyword:frame-relay

LOG_STD_ACTION

CERM_DP-4-DP_TX_BW_LIMIT

4-Warning

Maximum Tx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license.

Maximum Tx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license.

esg-ipsec

"Obtain 'hseck9' feature license and install it."

CERM_DP-4-DP_RX_BW_LIMIT

4-Warning

Maximum Rx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license.

Maximum Rx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license.

esg-ipsec

"Obtain 'hseck9' feature license and install it."

IPSEC-3-SA_SOFT_BYTE

3-Error

SA 0x[hec]0x[hec]

SA Softbyte Lifetime expiry event.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-SA_HARD_BYTE

3-Error

SA 0x[hec]0x[hec]

SA Hardbyte Lifetime expiry event.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_ERR_SA

3-Error

rc 0x[hec]

An error has occurred sending SA Byte Lifetime expiry event.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-ANTI_REPLAY

3-Error

SA 0x[hec]0x[hec]

Anti Replay check failed for the SA.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-SEQNO_OVERFLOW

3-Error

SA 0x[hec]0x[hec]

Sequence Number overflow for the SA.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-UNEXPECTED_ERROR

3-Error

orh.w0 0x[hec] error_op 0x[hec] SA 0x[hec]0x[hec]

Unexpected error for the SA.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-INVALID_SPI

3-Error

spi 0x[hec]

Got an invalid SPI value.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IN_POLICY_MISS

3-Error

sa 0x[hec] cp sa 0x[hec]

TCAM miss.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IN_POLICY_FAIL

3-Error

out sa 0x[hec]0x[hec] out sp 0x[hec]0x[hec] in sa 0x[hec]0x[hec] in sp 0x[hec]0x[hec]

In-Out SP mis-match.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_PAK_ALLOC_SA_EVENT

3-Error

event 0x[hec] sa 0x%llx

IPC pak allocation failed.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_PAK_SEND_SA_EVENT

3-Error

rc 0x[hec] event 0x[hec] sa 0x%llx

IPC send failed.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IKE_TED_MSG_LIMIT

3-Error

cnt [dec] sp 0x[hec] cp sp 0x[hec]

IKE TED Message Limit exceeded.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IKE_TED_MSG_RATE

3-Error

cnt [dec] sp 0x[hec] cp sp 0x[hec]

IKE TED Message Rate exceeded.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_PAK_ALLOC

3-Error

sp 0x[hec] cp sp 0x[hec]

IPC pak allocation failed.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_PAK_SEND

3-Error

rc 0x[hec] sp 0x[hec] cp sp 0x[hec]

IPC send failed.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-INVALID_VAL

3-Error

val 0x[hec]

Invalid value seen.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_HANDLER_ERR

3-Error

rc 0x[hec]

Error setting IPC Handler.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-DROP

3-Error

result type 0x[hec]

Classification results in Drop.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-INVALID_SA

3-Error

sa 0x[hec] cp sa 0x[hec]

SA is invalid.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-SA_NOT_FOUND

3-Error

-

SA not found.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-FOR_US_CLEARTEXT_POLICY_FAIL

3-Error

-

Policy fail for For-Us cleartext packet.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-TRANSIT_POLICY_FAIL

3-Error

-

Policy fail for transit ipsec packet.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-INTF_NOT_CFG

3-Error

-

Got an encrypted packet on an interface on which ipsec is not configured.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-FRAG_MPASS

3-Error

-

Multipass Error

cpp-ucode

LOG_STD_ACTION

IPSEC-3-INVALID_PROT

3-Error

invalid ipsec prot 0x[hec]

Got an invalid IPSEC protocol value.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-NO_MEMORY

3-Error

No memory 0x[hec]

No memory to send response back.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-MEM_REQ_FAILED

3-Error

IPC type 0x[hec]

Requesting more memory failed.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-CHUNK_CREATE_FAIL

3-Error

-

Chunk creation failed

cpp-ucode

LOG_STD_ACTION

IPSEC-3-CHUNK_DESTROY_FAIL

3-Error

-

Chunk destroy failed

cpp-ucode

LOG_STD_ACTION

IPSEC-3-CHUNK_DESTROY_ERROR

3-Error

-

Chunk destroy error force cleanup

cpp-ucode

LOG_STD_ACTION

IPSEC-3-MEM_EXTEND_FAILED

3-Error

IPC type 0x[hec]

Extending memory failed

cpp-ucode

LOG_STD_ACTION

IPSEC-3-IPC_INVALID_MSG_LEN

3-Error

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length

cpp-ucode

LOG_STD_ACTION

IPSEC-3-MEM_ALLOC_REACHED_LIMIT

3-Error

IPC type 0x[hec]

Cannot allocate more memory to store state for IPSec Traffic reached upper limit.

cpp-ucode

LOG_STD_ACTION

MONITOR-3-VPN_EVENT

3-Error

ipsec : [chars] : [dec] events

Crypto failure count hits limit. This message is just a warning not an error.

cpp-ucode

LOG_STD_ACTION

IPSEC-3-PKT_TOO_BIG

3-Error

IPSec Packet size [dec] larger than maximum supported size [dec] hence dropping it

Maximum size for packet with IPSEC encapsulation is 9K This packet exceeded the size limit hence dropping it.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-REPLAY_ERROR

3-Error

IPSec SA receives anti-replay error DP Handle [dec] src_addr %Ci dest_addr %Ci SPI 0x[hec]

Anti-replay error is encountered for this IPSec session.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-REPLAY_ERROR_IPV6

3-Error

IPSec SA receives anti-replay error DP Handle [dec] ipv6 src_addr [ipv6_addr] ipv6 dest_addr [ipv6_addr] SPI 0x[hec]

Anti-replay error is encountered for this IPSec session.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-RECVD_PKT_NOT_IPSEC

3-Error

Rec'd packet not an IPSEC packet dest_addr= %Ci src_addr= %Ci prot= [dec]\n

Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-RECVD_PKT_NOT_IPSECV6

3-Error

Rec'd packet not an IPSEC packet dest_addr= [ipv6_addr] src_addr= [ipv6_addr] prot= [dec]\n

Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-HMAC_ERROR

3-Error

IPSec SA receives HMAC error DP Handle [dec] src_addr %Ci dest_addr %Ci SPI 0x[hec]

HMAC calculation error is encountered for this IPSec session.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-HMAC_ERROR_V6

3-Error

IPSec SA receives HMAC error DP Handle [dec] ipv6 src_addr [ipv6_addr] ipv6 dest_addr [ipv6_addr] SPI 0x[hec]

HMAC calculation error is encountered for this IPSec session.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-FRAG_ERROR

3-Error

IPSec SA received fragmented ESP packet DP Handle [dec] src_addr %Ci dest_addr %Ci SPI 0x[hec]

Fragmented ESP packet is received for this IPSec session.

qfp-ipsec

LOG_STD_ACTION

IPSEC-3-FRAG_ERROR_IPV6

3-Error

IPSec SA received fragmented ESP packet DP Handle [dec] ipv6 src_addr [ipv6_addr] ipv6 dest_addr [ipv6_addr] SPI 0x[hec]

Fragmented ESP packet is received for this IPSec session.

qfp-ipsec

LOG_STD_ACTION

DTLS-3-REPLAY_ERROR_DTLS

3-Error

DTLS anti-replay error src_addr: %Ci src_port: [dec] dest_addr: %Ci dst_port: [dec]

Anti-replay error is encountered for this DTLS session.

qfp-ipsec

LOG_STD_ACTION

DTLS-3-REPLAY_ERROR_IPV6_DTLS

3-Error

DTLS anti-replay error ipv6 src_addr: [ipv6_addr] src_port: [dec] ipv6 dest_addr: [ipv6_addr] dst_port: [dec]

Anti-replay error is encountered for this DTLS session.

qfp-ipsec

LOG_STD_ACTION

L4_INSPECT-3-INVALID_CHUNK_ID

3-Error

Invalid chunk ID for protocol [dec]

Failed to determine chunk ID for specified protocol. Unable to free CFT feature object.

qfp-cxsc

LOG_STD_ACTION

LAYER2_BRIDGE-3-INIT_FAILED

3-Error

Initialization of the layer 2 bridging feature in QFP failed

Initialization of the layer 2 bridging feature in the QFP failed. This indicates a software failure.

qfp-bridging

LOG_STD_ACTION

LAYER2_BRIDGE-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for layer 2 bridging feature in QFP

Allocation of memory by the QFP layer 2 bridging feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

qfp-bridging

LOG_STD_ACTION

LAYER2_BRIDGE-3-PKT_REPLICA_INIT_FAILED

3-Error

Failed to register with generic packet replication for layer 2 bridging feature in QFP

Layer 2 bridging initialization of packet replication registration failed.

qfp-bridging

LOG_STD_ACTION

LAYER2_BRIDGE-3-HA_INVALID_STATE

3-Error

state [dec]

An invalid HA state was received from the HA infrastructure.

cpp-ucode

LOG_STD_ACTION

LAYER2_BRIDGE-3-HA_BULK_SYNC_FAIL

3-Error

rg [dec]

There was a failure such that Layer 2 bridge domain bulk sync did not occur

cpp-ucode

LOG_STD_ACTION

STILE-4-STATIC_SLINK_ALLOC_FAILED

4-Warning

Memory resources exhausted to configure custom/sub protocol

This message indicates that current user configuration could not be\n activated because of unavailability of memory resources.\n The NBAR cannot classify packets for this new protocol configured.

cpp-ucode

"The memory resource exhausion is happening because too many port range\n" "based protocols are configured by the user.\n" "Recommended action is to avoid very large range of ports."

STILE-3-PDL_DEBUG

3-Error

Action action_print is supported only in pdl debug mode. Text = [chars] Value = 0x[hec]

print action output

cpp-ucode

LOG_STD_ACTION

STILE-3-NBAR_DEBUG_REG_FAILED

3-Error

[dec]

NBAR Conditional debugging registration failed.

-

-

STILE-3-VM_ERRORS

3-Error

STILE VM traceback with cause: *[chars]* please see FP log for more information

-

qfp-nbar

-

IPV4_URPF-4-DROP

4-Warning

Dropping [chars] from [chars]

This message indicates that the router dropped a packet due to Unicast Reverse Path Forwarding check failure

qfp-ipucast

"This is an informational message"

IPV6_URPF-4-DROP

4-Warning

Dropping [chars] from [chars].

This message indicates that the router dropped a packet due to Unicast Reverse Path Forwarding check failure

qfp-ipucast

"This is an informational message"

FNF-3-KEY_SIZE_INVALID

3-Error

Unexpected key fields size: [dec]

Netflow attempted to install a flow with an invalid key fields size.

cpp-ucode

LOG_STD_ACTION

FNF-4-FREE_LIST_EMPTY

4-Warning

Monitor: 0x[hec]

Netflow attempted to install a flow but no free flow records were available.

cpp-ucode

LOG_STD_ACTION

FNF-3-FREE_LIST_ADD

3-Error

Failed for record: 0x[hec]

Netflow failed to return a record to the free list.

cpp-ucode

LOG_STD_ACTION

FNF-3-CLEANUP_ENTRY

3-Error

Failed

Netflow failed to clean up a record for reuse.

cpp-ucode

LOG_STD_ACTION

FNF-3-UNSUPPORTED_PROT

3-Error

[chars]

This protocol is unsupported.

cpp-ucode

LOG_STD_ACTION

FNF-3-INVALID_CMD

3-Error

Flow builder encountered an invalid command: [dec].

Flow builder doesn't support the command encountered in the instruction stream.

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_UNSUPPORTED_AGG_FMT

3-Error

Format: [dec]

Netflow doesn't support this aggregation type.

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_UNSUPPORTED_EXP_FMT

3-Error

Format: [dec]

Netflow doesn't support this export format.

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_UNSUPPORTED_OPTION

3-Error

Option: [dec]

Netflow doesn't support this export option.

cpp-ucode

LOG_STD_ACTION

FNF-3-IPFIX_UNSUPPORTED_MON_TYPE

3-Error

Monitor type: [dec]

IPFIX doesn't support this monitor type.

cpp-ucode

LOG_STD_ACTION

FNF-3-REFCNT_TIMEOUT

3-Error

never reached 0 for entry [hec]

Netflow timed out waiting for an flow cache entries refcnt. to hit 0. The entry was forced out

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_UNSUPPORTED_MMA_FIELD

3-Error

MMA global ID [dec] Netflow field [dec] is not supported by MMA

-

-

-

FNF-3-REFCNT_UNDERFLOW

3-Error

refcnt underflow for entry [hec]

Netflow error caused flow cache entry reference count to go negative. The decrement was rescinded

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_FIELD_LIST_VAR_INVALID

3-Error

Unknown field variety [dec] for field_id [dec]

Internal error Netflow field list entry mapped to unknown field variety

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_FIELD_UNEXPECTED_SIZE

3-Error

Unexpected size for field_id [dec] expected [dec]/got [dec]

Netflow specified unexpected size for field_id

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_FIELD_LIST_TS_CNT_KEY

3-Error

Field_id [dec] must be non-key

Netflow Field list specified timestamp/counter field as a key field which is not supported

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_FIELD_LIST_TOO_LARGE

3-Error

Field_list too large max [dec]

Netflow field list contains too many fields. At most 32 fields are supported including any hidden fields automatically added as necessary for record keeping

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_FREC_LAYOUT_TOO_LARGE

3-Error

Flow record layout too large max [dec]

Netflow field list results in a flow record layout which is too large. At most 128 bytes of flow record data is supported including any padding and any hidden fields automatically added as necessary for record keeping

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_FIELD_LIST_MEM_INSUFFICIENT

3-Error

Insufficient memory [dec] for field_list

Internal error netflow client provided insufficient memory to process a field list

cpp-ucode

LOG_STD_ACTION

FNF-3-INVALID_FO

3-Error

FNF FO is not valid

FNF feature object is not valid.

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_CWALK_FLEXIBLE_UNEXPECTED_LAYOUT

3-Error

Failed copy to CLI buffer PI will receive zero buffer

Failed copy to CLI buffer during the walk process fill the buffer with 0

cpp-ucode

LOG_STD_ACTION

FNF-6-DYNAMIC_MONITORS_OVER_SUBSCRIPTION

6-Information

Interface [chars] dir=[chars]: the number of monitors that should run on

QFP maximum supported number of monitors per packet was exceeded. As a result the excess number of monitors will not run on the packet. Static monitors always take priority over policy-map monitors.

cpp-ucode

LOG_STD_DBG_ACTION

FNF-6-SYNC_CACHE_TOO_MANY_RECS_FOR_INTERVAL

6-Information

For synchronized cache the number of records is larger than can be exported in configured interval.

The number of records is too large for the configured interval. As a result some records may not be exported in a timely manner. Consider reducing cache size or increasing interval length.

cpp-ucode

LOG_STD_DBG_ACTION

FNF-3-DEBUG_REG_FAILED

3-Error

FNF fails to registrate with Conditional Debugging.

FNF fails to registrate with Conditional Debugging infra.

cpp-ucode

LOG_STD_ACTION

FNF-3-CFT_REG_FAILED

3-Error

FNF fails to connect to CFT infra.

FNF fails to connect to CFT infra.

cpp-ucode

LOG_STD_ACTION

FNF-3-FNF_EXPORT_BUILD_TYPE_FAILED

3-Error

Format: [dec]

FNF Exporter build failed. unknown type.

cpp-ucode

-

FRAG-3-FRAG_STATE_MEM_REQ_FAILED

3-Error

-

IPC failure occurred when attempting to request more fragment state pool memory.

qfp

LOG_STD_ACTION

FRAG-3-FRAG_STATE_MEM_INIT_FAILED

3-Error

-

Failure occurred initializing fragment state pool.

qfp

LOG_STD_ACTION

FRAG-3-FRAG_DESC_MEM_REQ_FAILED

3-Error

-

IPC Failure occurred when attempting to request more fragment descriptor pool memory.

qfp

LOG_STD_ACTION

FRAG-3-FRAG_DESC_MEM_INIT_FAILED

3-Error

-

Failure occurred initializing fragment descriptor pool.

qfp

LOG_STD_ACTION

FRAG-3-REASSEMBLY_ERR

3-Error

Reassembly/VFR encountered an error: [chars]

Reassembly/VFR encountered a runtime error as indicated

qfp

LOG_STD_ACTION

FRAG-3-REASSEMBLY_DBG

3-Error

Reassembly/VFR encountered an error: [chars] [chars] %lu [chars] %lu

Reassembly/VFR encountered a runtime error as indicated in the message with parameter data for debug

qfp

LOG_STD_ACTION

FRAG-2-UNENABLED

2-Critical

[chars] feature not enabled at interface [chars] packet cannot be processed

Reassembly or fragmentation feature as indicated not enabled by the control plane. This is a critical problem.

qfp

LOG_STD_ACTION

FRAG-3-INVALID_MTU

3-Error

[chars] feature failed at interface [chars] due to invalid L3 MTU %lu

Fragmentation was not able to be performed due to invalid adj L3 MTU given by the control plane.

qfp

LOG_STD_ACTION

FRAG-3-INVALID_QFP_NO

3-Error

Invalid qfp device no.: [chars]

Invalid qfp device no.

qfp

LOG_STD_ACTION

DIALER_LIST-3-CHUNK_CREATE_FAIL

3-Error

DIALER LIST - fialed to create chunk pool

Chunk create failed. Dialer List will not be able to finish initialization.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST-3-CHUNK_DESTROY_FAIL

3-Error

DIALER LIST - fialed to destroy chunk pool

Chunk destroy failed.

cpp-ucode

LOG_STD_ACTION

LAYER2_SVI-3-INIT_FAILED

3-Error

Initialization of the SVI feature in QFP failed

Initialization of the SVI feature in the QFP failed. This indicates a software failure.

qfp-switch-infra

LOG_STD_ACTION

LAYER2_SVI-3-ALLOC_FAILED

3-Error

Allocation of [chars] memory failed for SVI feature in QFP

Allocation of memory by the QFP SVI feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure

qfp-switch-infra

LOG_STD_ACTION

LAYER2_SVI-3-PKT_REPLICA_INIT_FAILED

3-Error

Failed to register with generic packet replication for SVI feature in QFP

SVI initialization of packet replication registration failed.

qfp-switch-infra

LOG_STD_ACTION

NAT-3-ALLOC_FAIL

3-Error

data 0x[hec]

A request exceeded for memory allocation failed

cpp-ucode

LOG_STD_ACTION

NAT-3-RMAP_OP_FAIL

3-Error

Routemap hash table not set up attempted [chars]

-

-

-

NAT-3-MAPPING_REFCNT_FAIL

3-Error

refcount [dec]

The mapping reference count is below zero. This indicates that the reference count incrementing and decrementing operations are out of sync

cpp-ucode

LOG_STD_ACTION

NAT-3-DYN_PAT_MAP_UPD_OR_ADD_FAIL

3-Error

rc [dec]

The add or update of a dynamic pat mapping failed with the assoicated return code. This will generally mean that the IOS configuration is now out of sync with the data plane. The mapping should be removed from the configuration to try to get things back in sync.

cpp-ucode

LOG_STD_ACTION

NAT-3-EMPTY_CHUNK

3-Error

id [dec]

The memory provided by the client to the datapath initilization is NULL

cpp-ucode

LOG_STD_ACTION

NAT-3-CHUNK_ID_MISMATCH

3-Error

id [dec] not found

The chunk ID provided by the client doesn't match any of the available chunk IDs. Hence a valid chunk could not be found for the given chunk ID.

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_NO_BUF

3-Error

-

There was not enough memory to send the HA record

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_BULK_SYNC_FAIL

3-Error

flags 0x[hec] rg [dec]

There was a failure such that NAT Bulk Sync did not occur

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_COULD_NOT_FIND_SESS

3-Error

in_orig adr [hec] port [hec] out_trans adr [hec] port [hec] vrf [hec] prot [hec] cook [hec] [hec]

Standby could not find the matching session indicated by the HA message

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_STANDBY_CLR_DB_FAILED

3-Error

rc=[dec]

Standby failed trying to clear databased with indicated return code

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_COULD_NOT_CREATE_SESS

3-Error

in_orig adr [hec] port [hec] out_trans adr [hec] port [hec] vrf [hec] prot [hec] cook %llu rg [dec]

Standby could not create the session indicated by the HA message

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_COULD_NOT_LOCK_PARENT

3-Error

in_orig adr [hec] port [hec] out_trans adr [hec] port [hec] vrf [hec] prot [hec] cook %llu

-

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_COULD_NOT_CREATE_BIND

3-Error

idomain [dec] orig adr [hec] port [hec] trans adr [hec] port [hec] vrf [hec] prot [hec] rg [dec]

Standby could not create the bind indicated by the HA message

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_INVALID_MSG_RCVD

3-Error

invalid value [dec] opcode 0x[hec] version 0x[hec]

Standby received an invalid NAT HA message

cpp-ucode

LOG_STD_ACTION

NAT-4-HA_INVALID_MSGVER_RCVD

4-Warning

invalid version [dec]

Standby received an invalid NAT HA message

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_INVALID_STATE

3-Error

state [dec]

An invalid HA state was received from the HA infrastructure.

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_COULD_NOT_ALLOC_ADDR

3-Error

addr %Ci port [hec]

The standby NAT could not allocate the address requested by the active

cpp-ucode

LOG_STD_ACTION

NAT-3-HA_COULD_NOT_FIND_POOL

3-Error

pool_id [dec]

The standby NAT could find the pool indicated by the active

cpp-ucode

LOG_STD_ACTION

NAT-3-HSL_ALLOC_FAIL

3-Error

[chars]

High Speed logging memory allocation failed. When this happens the event\n will not be exported to the collector. This indicates a temporary \n condition when the system runs low on memory. The failure does not have \n any effects on the operation of NAT \n

cpp-ucode

LOG_STD_ACTION

NAT-6-LOG_TRANSLATION

6-Information

[chars] Translation [chars] %Ci:[dec] %Ci:[dec] %Ci:[dec] %Ci:[dec] [dec]

A translation was created as a result of either a configuration or traffic\n flowing through the NAT subsystem

cpp-ucode

"This message is for debugging purposes only and gets logged only when \n" "logging is turned on"

NAT-3-STATIC_MAP_ADD_FAIL

3-Error

local addr %Ci global addr %Ci [chars]

This is an information message which occurs when NAT is configured and a frame is dropped due to the default maximum entries limit. Starting with release 5 XNE NAT will use a default max-entries in the data plane based on the ESP type. This will not show in the configuration and is overriden by any user configuration of 'ip nat trans max-entries <value>'. The purpose of the default data plane limit is to protect the box from memory exhaustion which could occur if no limit is enforced.

cpp-ucode

LOG_STD_ACTION

NAT-4-ALL_HOST_MAX_ENTRIES

4-Warning

all-host maximum limit of [dec] reached for [chars].

This message indicates that maximum limit for all-host entries was reached.

cpp-ucode

-

NAT-4-PER_HOST_MAX_ENTRIES

4-Warning

per-host maximum limit of [dec] reached for [chars].

This message indicates that maximum limit for per-host entries was reached.

cpp-ucode

-

NAT-4-ALL_VRF_MAX_ENTRIES

4-Warning

all-vrf maximum limit of [dec] reached for [dec].

This message indicates that maximum limit for all-vrf entries was reached.

cpp-ucode

-

NAT-4-PER_VRF_MAX_ENTRIES

4-Warning

per-vrf maximum limit of [dec] reached for [dec].

This message indicates that an address could not be allocated from a pool because there were no free addresses in the pool at that time.

cpp-ucode

-

NAT-6-NON_PAT_TRANS_DETECT

6-Information

Non-PATable translation for [chars]: on pool [dec] orig_ip %Ci trans_ip %Ci alg_type [dec][chars] input intf [chars] mapping id [dec] created by pkt:

This message indicates that an address could not be allocated from a pool for a specific client address because there were no free addresses in the pool at that time.

cpp-ucode

-

NAT-6-POOL_WATERMARK_HIGH

6-Information

[chars] High watermark reached for pool [dec]

This message indicates that pool usage has crossed its high watermark. Pool may exhaust soon.

-

-

NAT-6-POOL_WATERMARK_LOW

6-Information

[chars] Low watermark reached for pool [dec]

This message indicates that pool usage has crossed its low watermark. Pool should have enough address.

cpp-ucode

-

NAT-6-CLEAR_FAIL_TRANS_IN_USE

6-Information

-

The requested clear failed because the transaction was in use.\n Some clear commands support a 'forced' keyword which allows you \n to override this.\n

cpp-ucode

LOG_STD_ACTION

NAT-3-PER_VFR_HSL_ADD_FAILED

3-Error

-

The attempt to turn on NAT HSL for a vrfid [dec] failed. Please remove configuration and try again.\n

cpp-ucode

LOG_STD_ACTION

NAT-3-POOL_ADD_FAIL

3-Error

pool-id [dec] rc [dec]

A request from the active to process a clear translation failed.\n Please retry.\n

cpp-ucode

LOG_STD_ACTION

NAT-3-SHOW_TRANS_FAIL

3-Error

unable to show [dec] entries from bucket [dec]

Unable to show some entries from session database. If using verbose try using non-verbose. Otherwise situation is likely to be temporary. Or it may be wise to do 'clear ip nat trans *' as a very odd session distribution has occurred.\n

cpp-ucode

LOG_STD_ACTION

NAT-3-SHOW_LIMIT_FAIL

3-Error

unable to show [dec] entries from bucket [dec]

This is an information message which occurs when NAT is unable to show all address binds due to an internal error. Please try operation again.

cpp-ucode

LOG_STD_ACTION

NAT-3-STATIC_MAP_ADD_FAILED

3-Error

local addr %Ci global addr %Ci [chars] %Ci %Ci

-

-

-

NAT-3-DYN_MAP_ADD_FAIL

3-Error

[chars]

The add of a dynamic mapping failed. This will generally mean that the IOS configuration is now out of sync with the data plane. The mapping should be removed and then re-added to try to get things back in sync.

cpp-ucode

LOG_STD_ACTION

NAT-4-FORCED_DEL_BIND_FAILED

4-Warning

Unable to find bind to forcibly delete

This is an information message which occurs when NAT is unable to find a bind even though IOS thinks the bind exists. Please try other methods of clearing transaction.

cpp-ucode

-

NAT-3-DP_REL_FAIL

3-Error

DP REL FAIL retry count [dec] exceeded max

The dp release fail due to too many retry on freeing session chunk

cpp-ucode

LOG_STD_ACTION

NAT-4-SEQ_DELTA_LIST_CORRUPT

4-Warning

Sequence Delta list tail pointer null in error

For unknown reasons sequence delta list tail pointer is null

cpp-ucode

LOG_STD_ACTION

ESS_IPSUB-3-ESS_IPSUB_STUB

3-Error

CPP ESS IPSUB executes stub entry in [chars] direction

Cisco internal software error. CPP ESS IPSUB stub entry got executed. The packet will be dropped.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_IPSUB-3-FSOL_THROTTLE_ERR

3-Error

Allocation of [chars] memory failed for ESS IP Subscriber

Allocation of memory resource demanded by ESS IPSUB FSOL throttle failed. This is a serious problem at the ESS IPSUB FSOL initialization for throttling.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_FEATURE-3-ESF_STUB

3-Error

CPP ESS per-session feature [chars] executes stub entry in [chars] direction

Cisco internal software error. CPP ESS per-session feature stub entry got executed. The packet will be dropped.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_FEATURE-4-ESF_DROP_POLICY

4-Warning

CPP ESS feature encounted unexpected linktype=[dec]

Cisco internal software error. CPP ESS per-session feature encounted unexpected linktype when executing output drop policy

qfp-bb keyword:none

LOG_STD_ACTION

ESS_SWITCH-3-ESS_STUB

3-Error

CPP ESS switching [chars] feature executes stub entry in [chars] direction

Cisco internal software error. CPP ESS Switching feature stub entry got executed. The packet will be dropped.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_SWITCH-3-STATS_INVALID_PTR

3-Error

CPP ESS Switching invalid statistics block for session [chars].

Cisco internal software error. CPP ESS Switching session contains an invalid statistics block. The session statistics is lost.

qfp-bb keyword:none

LOG_STD_ACTION

SSL-3-SSL_REC_HDR_BUF_OVERFLOW

3-Error

QFP SSL record header buffer overflow

Cisco internal software error. QFP SSL record processing detected header buffer overflow condition. The SSL connection will not be functional while this condition exists.

qfp-ssl keyword:none

LOG_STD_ACTION

SSL-3-SSL_STUB

3-Error

QFP SSL [chars] feature executes stub entry in [chars] direction

Cisco internal software error. QFP SSL feature stub entry got executed. The packet will be dropped.

qfp-ssl keyword:none

LOG_STD_ACTION

IPV6_FORWARDING-2-CAUSE_THROTTLE_ERR

2-Critical

Allocation of ipv6 throttle [chars] memory failed

Allocation of memory resource use by ipv6 throttle fail

cpp-ucode

LOG_STD_ACTION

IPV6_FORWARDING-3-CAUSE_LINKTYPE_ERR

3-Error

Unsupported link type [chars] dropping packet

Link type is unsupported at the current time.

cpp-ucode

LOG_STD_ACTION

IPV6_FORWARDING-4-CHECKSUM_ERR

4-Warning

Checksum buffer walk failed

Internal problem occured during calculating segmented packet checksum.

cpp-ucode

LOG_STD_ACTION

IPV6_FORWARDING-3-TABLE_ID_SZ_ERR

3-Error

Table ID size configured incorrectly: [dec]

Table ID size must be less than or equal to 16 or 32 bits.

cpp-ucode

LOG_STD_ACTION

IPV6_VFR-4-TINY_FRAGMENTS

4-Warning

Dropping [chars] from [chars] due to tiny fragment.

This message indicates that the router is receiving tiny fragments - meaning the initial fragment does not have complete layer 4 header

qfp-ipucast

"This is an informational message"

IPV6_VFR-4-OVERLAP_FRAGMENTS

4-Warning

Dropping [chars] from [chars] due to overlap fragment.

This message is logged whenever the router encounters overlap fragments. Overlap fragment means offset of one fragment overlaps the offset of another fragment. For example if first fragment's offset is 0 and length is 800 then the second fragments offset must be 800. If second fragment's offset is less than 800 that means the second fragment overlaps the first fragment.

qfp-ipucast

"This could possibly be an attack configure a static ACL to prevent " "further overlap fragments from the sender"

IPV6_VFR-4-FRAG_TABLE_OVERFLOW

4-Warning

Dropping [chars] from [chars] due to fragment table overflow.

This means the number of datagrams reassembled at a time reached its maximum limit increase the value of max-reassemblies using ipv6 virtual-reassembly in/out max-reassemblies <number>

qfp-ipucast

-

IPV6_VFR-4-TOO_MANY_FRAGMENTS

4-Warning

Dropping [chars] from [chars] due to too many fragments for the datagram.

This message indicates the datagram being reassembled has received more fragments than its threshold value

qfp-ipucast

"Check if the fragments received are from a genuine source if so " "increase the value of max-fragments using the CLI " "ipv6 virtual-reassembly in/out max-fragments <number>"

IPV6_VFR-4-INVALID_FRAG_LENGTH

4-Warning

Dropping [chars] from [chars] due to invalid fragment length.

This message indicates that the router has encountered a fragment with invalid packet length

qfp-ipucast

"To prevent further attacks its highly recommended that an ACL " "be configured to drop any traffic from the sender"

IPV6_VFR-4-TIMEOUT

4-Warning

Dropping [chars] from [chars] due to virtual reassembly timeout.

This message indicates that the router is trying to do virtual-reassembly for fragments but got timeout before receiving all the fragments for a datagram

qfp-ipucast

"This is an informational message"

IPV6_VFR-4-CONFIG

4-Warning

Dropping [chars] from [chars] due to system config.

This message indicates that the router drops fragment packet due to ipv6 virtual-reassembly drop-fragments

qfp-ipucast

"This is an informational message"

IPV6_VFR-4-INVALID_DROP_LOG_TYPE

4-Warning

Dropping [chars] from [chars]. Invalid drop log type [dec]

Unsupported drop log type

qfp-ipucast

LOG_STD_ACTION

MPLS_FORWARDING-2-CAUSE_THROTTLE_ERR

2-Critical

Allocation of mpls throttle [chars] memory failed

Allocation of memory resource use by mpls throttle fail

cpp-ucode

LOG_STD_ACTION

CENT-3-CENT_RC_AT_FO_OVERWRITE

3-Error

FO overwritten detected: magic [hec] table_id [hec] next_hop [hec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:cent

LOG_STD_ACTION

NAT64-6-V4UDP_0CSUM_FRAG

6-Information

source IP %Ci dest IP %Ci source port [dec] dest port [dec]

A first fragment of an IPv4 UDP packet with 0 checksum has been dropped

cpp-ucode

LOG_STD_ACTION

NAT64-6-DEFAULT_MAX_ENTRIES

6-Information

default max entries value [dec]

This is an information message which occurs when NAT is configured and a frame is dropped due to the default maximum entries limit. Starting with release 5 XNE NAT will use a default max-entries in the data plane based on the ESP type. This will not show in the configuration and is overriden by any user configuration of 'ip nat trans max-entries <value>'. The purpose of the default data plane limit is to protect the box from memory exhaustion which could occur if no limit is enforced.

cpp-ucode

-

NAT64-3-CLEAR_FAIL_TRANS_IN_USE

3-Error

-

The requested clear failed because the transaction was in use.\n Some clear commands support a 'forced' keyword which allows you \n to override this.\n

cpp-ucode

LOG_STD_ACTION

NAT64-3-EMPTY_CHUNK

3-Error

id [dec]

The memory provided by the client to the datapath initilization is NULL

cpp-ucode

LOG_STD_ACTION

NAT64-3-CHUNK_ID_MISMATCH

3-Error

id [dec] not found

The chunk ID provided by the client doesn't match any of the available chunk IDs. Hence a valid chunk could not be found for the given chunk ID.

cpp-ucode

LOG_STD_ACTION

NAT64-4-STATIC_MAP_ADD_FAIL

4-Warning

[chars] v4 addr %Ci v6 addr [ipv6_addr] [chars]

An add of a static NAT64 mapping failed due to listed reason.\n This mapping will be in the IOS configuration but is not active\n in the data plane. It is recommended to remove the mapping \n from the configuration\n

cpp-ucode

LOG_STD_ACTION

NAT64-6-SHOW_TRANS_FAIL

6-Information

unable to show [dec] entries from bucket %

Unable to show some entries from session/bind database. If using verbose try using non-verbose. Otherwise situation is likely to be temporary. Or it may be wise to do 'clear ip nat trans *' as a very odd session distribution has occurred.\n

cpp-ucode

LOG_STD_ACTION

NAT64-6-LOOPV6

6-Information

src IP [ipv6_addr] dest IP [ipv6_addr]

IPv6 packet has been dropped due to looping inside of NAT64. See recommended action

cpp-ucode

"There are 2 most likely items that should be checked for this error:\n" "1 check that none of the NAT64 interfaces are showdown "

NAT64-6-LOOPV4

6-Information

src IP %Ci dest IP %Ci

IPv4 packet has been dropped due to looping inside of NAT64. See recommended action

cpp-ucode

"There are 2 most likely items that should be checked for this error:\n" "1 check that none of the NAT64 interfaces are disabled\n"

NAT64-3-NAT64_POOL_ADD_FAIL

3-Error

pool-id [dec] rc [dec]

This message indicates that an address could not be allocated from a pool because there were no free addresses in the pool at that time.

cpp-ucode

LOG_STD_ACTION

NAT64-3-NAT64_MAPPING_REFCNT_FAIL

3-Error

refcount [dec]

A request from the active to process a clear translation failed.\n Please retry.\n

cpp-ucode

LOG_STD_ACTION

NAT64-3-HA_INVALID_MSG_RCVD

3-Error

invalid value [dec] opcode 0x[hec] version 0x[hec]

Standby received an invalid NAT64 HA message

cpp-ucode

LOG_STD_ACTION

NAT64-3-HA_BULK_SYNC_FAIL

3-Error

flags 0x[hec] rg [dec]

There was a failure such that NAT64 Bulk Sync did not occur

cpp-ucode

LOG_STD_ACTION

NAT64-3-HA_INVALID_STATE

3-Error

state [dec]

An invalid HA state was received from the HA infrastructure.

cpp-ucode

LOG_STD_ACTION

TCP-3-TCP_REG_FAILED

3-Error

QFP TCP registers failed

Cisco internal software error. QFP TCP feature initialization detected that registration failed. QFP TCP will not be functional while this condition exists.

qfp-tcp keyword:tcp

LOG_STD_ACTION

CXSC-3-CXSC_COND_DEBUG_REG_FAILED

3-Error

[chars]

Failure occurred when attempting to Register/Initialize conditional debugging.

qfp-ucode

LOG_STD_ACTION

POP3_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

POP3 code has detected a cleartext logon attempt in the inspected POP3 connection while secure-login is configured. This command has been rejected.

cpp-ucode

"This message is for informational purposed only but may indicate" "a security problem."

HTTP_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

This message indicates detection of an HTTP Java applet in a response

cpp-ucode

"This message is for informational purposed only but may indicate" " a security problem."

GTP_AIC-3-CHUNK_CREATE_FAIL

3-Error

-

This message indicates that the packet is dropped by GTP AIC.

cpp-ucode

"This message is for informational purposed only but may indicate " "a security problem."

IMAP_ALG-3-CHUNK_CREATE_FAIL

3-Error

-

IMAP code has detected a cleartext logon attempt in the inspected IMAP connection while secure-login is configured. This command has been rejected.

cpp-ucode

"This message is for informational purposed only but may indicate" "a security problem."

SMTP_ALG-3-SMTP_CHUNK_CREATE_FAIL

3-Error

-

Triggers on an invalid SMTP command in the SMTP connection. This message indicates that a suspicious violation was detetected that may be an attack to the mail server system.

cpp-ucode

"This is unusual traffic and may warrant investigation."

QOS-3-QOS_CLASSIFY_FAIL

3-Error

dataplane classification error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-QOS_CLASSIFY_FAIL_CHILD_IN

3-Error

child dataplane classification error for input interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-QOS_CLASSIFY_FAIL_CHILD_OUT

3-Error

child dataplane classification error for output interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-QOS_CLASSIFY_FAIL_CCE_IN

3-Error

dataplane classification error for input interface [chars] [hec] [hec] [hec] [hec]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-QOS_CLASSIFY_FAIL_CCE_OUT

3-Error

dataplane classification error for output interface [chars] [hec] [hec] [hec] [hec]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a classification failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-POLICE_FAIL_ADDRESS_IN

3-Error

dataplane policer error for input interface [chars] [hec] [hec] [hec] [hec] [hec]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a policer failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-POLICE_FAIL_ADDRESS_OUT

3-Error

dataplane policer error for output interface [chars] [hec] [hec] [hec] [hec] [hec]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a policer failure. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-POLICE_CLASSIFY_FAIL

3-Error

Color aware policer classification error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of a service policy due to a classification failure on a color aware policer class. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_QID

3-Error

Queuing error for interface [chars] qid [dec] wred [hec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_CLASS_QID

3-Error

Class Queuing error for interface [chars] qid [dec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_STAT_QID

3-Error

Stat Queuing error for interface [chars] qid [dec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_DEFAULT_QID

3-Error

Default Queuing error for interface [chars] qid [dec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-VALID_DEFAULT_QID

3-Error

Using Default Queue for interface [chars] qid [dec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_Q_ADDRESS

3-Error

Invalid Queue address for interface [chars] qaddr [hec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_STATS_INFO

3-Error

Invalid address [hec] detected

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_MARKER_STATS_INFO

3-Error

Invalid address [hec] detected

Cisco internal software error. The dataplane was unable to complete a statistics update on a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_WRED_THRESH_ADDR

3-Error

Wred threshold address is invalid addr [dec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_BQS_QUEUE_INFO

3-Error

Drop policy given an invalid scheduling queue/wred [dec]/[dec]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_HIER_EXPORT_COUNT

3-Error

Invalid export count [hec] detected

Cisco internal software error. The dataplane was unable to complete a hierarchy export on a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_HIER_EXPORT_CLASS_ID

3-Error

Invalid export class ID detected

Cisco internal software error. The dataplane was unable to complete a hierarchy export on a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_DEFAULT_JIB_HDR

3-Error

Queuing error for interface [chars]

Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-INVALID_CAC_PKT_INFO

3-Error

QoS CAC: failed to get the CAC packet info for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L3Prot=[dec] L4Prot=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a packet. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-CAC_ATTACH_FAILED

3-Error

QoS CAC: failed to attach cft flow object for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L4Prot=[dec] num flows=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to a CFT data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-CAC_ALLOC_FAILED

3-Error

QoS CAC: failed to allocate a cft flow object for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L4Prot=[dec] num flows=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to processing more flows than CAC's scale limit

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-CAC_FLOW_CREATE_FAILED

3-Error

QoS CAC: failed to create a flow in the cft for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L3Prot=[dec] L4Prot=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to processing more flows than the CFT's scale limit

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-CAC_FLOW_LOCK_FAILED

3-Error

QoS CAC: failed to get a flow lock for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L3Prot=[dec] L4Prot=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to a CFT data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-CAC_FLOW_REPORT_FAILED

3-Error

QoS CAC: failed to report flow for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L3Prot=[dec] L4Prot=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-GET_CAC_INFO_FAILED

3-Error

QoS CAC: failed to retreive the CAC config for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L3Prot=[dec] L4Prot=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to a data initialization error

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-GET_CAC_FLOW_OBJECT_FAILED

3-Error

QoS CAC: failed to retreive the CAC flow object for interface [chars] srcIP=%Ci dstIP=%Ci srcPort=[dec] dstPort=[dec] L3Prot=[dec] L4Prot=[dec]

Cisco internal software error. The dataplane was unable to complete the CAC processing for a flow. This is likely due to processing more flows than the CFT's scale limit

cpp-ucode keyword:qos

LOG_STD_ACTION

QOS-3-CAC_PROXY_MSG_FAIL

3-Error

Failure when handling QoS CAC proxy message [chars]

-

-

-

QOS-3-CAC_EXPORT_DROPPED_PKT

3-Error

Dropped a packet for QoS CAC when exporting flow records via HSL to the control plane

Cisco internal software error. The dataplane dropped one or more packets containing QoS CAC export records. This is likely due to over-driving the punt/hsl messaging channel.

asr1k-qos keyword:none

LOG_STD_ACTION

QOS-3-CAC_EXPORT_DROPPED_RECORD

3-Error

Dropped a flow record for QoS CAC CAC ID [hex] when attempting

Cisco internal software error. The dataplane dropped one or more flow records for QoS CAC. This is likely due to buffer allocation error and over-driving the punt/hsl messaging channel.

asr1k-qos keyword:none

LOG_STD_ACTION

QOS-3-INVALID_ATM_GROUP_MEMBER_UIDB

3-Error

Dropped a flow from ATM interface [chars] due to invalid oup_member_uidb_config

Cisco internal software error. Fail to get QOS config from ATM input terface due to invalid group_member_uidb_config.

cpp-ucode keyword:qos

LOG_STD_ACTION

SSLVPN-3-SSL_APPL_REG_FAILED

3-Error

QFP SSLVPN registers to SSL library failed

Cisco internal software error. QFP SSLVPN feature initialization detected that the SSL library registration failed. QFP SSLVPN will not be functional while this condition exists.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-3-SSLVPN_CTX_CLOSE_FAILED

3-Error

QFP SSLVPN failed to close SSLVPN context: [%-#016llx] Close request reason: [chars]

Cisco internal software error. QFP SSLVPN feature failed to close an SSLVPN context.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-3-SSLVPN_CTX_PUNT_FAILED

3-Error

QFP SSLVPN failed to send [chars] for context: [%-#016llx] to control plane

Cisco internal software error. QFP SSLVPN featre failed to send a message to control plane.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-3-SSLVPN_SOCKET_ACTION_FAILED

3-Error

QFP SSLVPN failed to [chars] socket [hec] [[chars]err [dec]]

Cisco internal software error. QFP SSLVPN feature failed to accomplish socket action.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-5-SSLVPN_SESS_SSL_TLS_ERROR

5-Notice

vw_ctx: [chars] vw_gw: [chars] i_vrf [dec] f_vrf [dec] status:SSL/TLS connection error with remote at [inet]:[dec]

This message indicates that SSL/TLS connection has encountered error. This normally means that either handshake failed or protocol error occured during life-time of the connection.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-3-SSLVPN_STUB

3-Error

QFP SSLVPN [chars] feature executes stub entry in [chars] direction

Cisco internal software error. QFP SSLVPN feature stub entry got executed. The packet will be dropped.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-3-SSLVPN_STUB_TW_MEM_LEAK

3-Error

QFP SSLVPN feature leaks timing wheel memory

Cisco internal software error. QFP SSLVPN feature allocates unused timing wheel memory size: [dec]

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN-3-SSLVPN_STUB_DATA_MSG_LOST

3-Error

QFP SSLVPN stub function failed to transmit data message size: [dec].

-

-

-

THREAT_DEFENSE-3-VTCP_INIT_FAILED

3-Error

-

Initialization of VTCP failed.

cpp-ucode

LOG_STD_ACTION

THREAT_DEFENSE-3-DESTROY_CHUNK_FAILED

3-Error

-

Destroy chunk failed.

cpp-ucode

LOG_STD_ACTION

THREAT_DEFENSE-4-TD_ERM_AVERAGE_THREAT

4-Warning

Event Rate Monitoring: Average threat identified. Zone [[chars]] event type [[chars]] average [[dec]] configured threshold [[dec]]

Event Rate Monitoring: Average threat identified

cpp-ucode

LOG_STD_ACTION

THREAT_DEFENSE-4-TD_ERM_BURST_THREAT

4-Warning

Event Rate Monitoring: Burst threat identified. Zone [[chars]] event type [[chars]] configured threshold [[dec]]

Event Rate Monitoring: Burst threat identified

cpp-ucode

LOG_STD_ACTION

VTCP-3-VTCP_CREATE_CB_MALLOC_FAILED

3-Error

-

Malloc failed during VTCP create callback.

cpp-ucode

LOG_STD_ACTION

CCE-3-CCE_NON_TCAM_CLASSIFY

3-Error

Dataplane classification error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of a classification request because an invalid form of classification was selected. This is likely due to a data initialization error

cpp-ucode keyword:cce

LOG_STD_ACTION

CCE-3-CCE_IPV6_COMPR_CLASSIFY_FAIL

3-Error

Dataplane IPV6 compression classification error for interface [chars]

Cisco internal software error. The dataplane was unable to complete processing of an IPV6 prefix classification request due to a miss on a TCAM lookup. This is likely due to a data initialization error

cpp-ucode keyword:cce

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_OCE_CHAIN_ERR

3-Error

OCE chain error dropping packet

OCE chain pointer contain an error

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_IPV6_ERR

3-Error

IPv6 not supported dropping packet

IPV6 over MPLS not supported

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_OCE_CHOICE_ERR

3-Error

OCE Choice unsupported link error [chars] 0x%X

OCE Choice unsupported link error

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_OCE_ADJ_ID

3-Error

hash table not initialized

OCE adjacency id handle hash table not initialized

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-2-CAUSE_FRR_STATE_ERR

2-Critical

Illegal FRR OCE state - FRR OCE state = [dec]

Invalid FRR OCE state

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-2-CAUSE_FRR_BACKUP_LABEL_ERR

2-Critical

FRR OCE node protection error no backup label

No backup label available for FRR when node protection is invoked

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-2-CAUSE_ILLEGAL_OBJ_ERR

2-Critical

ILLEGAL OCE - unexpected oce

This object should not be seen by the forwarding code

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-2-CAUSE_OCE_LINKTYPE_ERR

2-Critical

LINKTYPE ERROR OCE - Linktype error in oce

Link type not supported in OCE

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_OCE_INJECT_ADJ

3-Error

unexpected subtype

OCE adjacency id - unknown fixup subtype

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_OCE_COUNTER_EXCEED_STACK

3-Error

OCE counter stack exceed

OCE counter exceed the allocated stack size

cpp-ucode

LOG_STD_ACTION

OCE_FORWARDING-3-CAUSE_OCE_BUNDLE_ERR

3-Error

OCE Bundle unsupported link error [chars] 0x%X

A request exceeded the feature invocation call stack

cpp-ucode

LOG_STD_ACTION

IPC-3-CONTROL

3-Error

Unhandled message subtype [dec]

An IPC control message was received containing an unrecognized type.

cpp-ucode

LOG_STD_ACTION

IPC-3-NOHANDLER

3-Error

message type [dec] from [chars]

An IPC message was received containing an unrecognized type.

cpp-ucode

LOG_STD_ACTION

IPC-3-PGENALLOC

3-Error

[dec] bytes

Allocating a packet of the specified size failed.

cpp-ucode

LOG_STD_ACTION

IPC-3-PGENSEND

3-Error

[chars]

Sending a generated packet failed for the specified reason.

cpp-ucode

LOG_STD_ACTION

IPC-3-REPLY

3-Error

unexpected from [chars]

An unexpected reply was received from the specified source.

cpp-ucode

LOG_STD_ACTION

IPC-3-BADMSG

3-Error

received type [dec]

An IPC message was received containing an invalid message type.

cpp-ucode

LOG_STD_ACTION

IPC-6-ACKRETRY

6-Information

required [dec] retries

Allocating an IPC acknowledgement failed on the first attempt but succeeded on a later attempt.

cpp-ucode

LOG_STD_ACTION

IPC-3-ACKALLOC

3-Error

couldn't send to [chars]

Allocating an IPC acknowledgement failed with the likely result that some software on the specified source node will timeout.

cpp-ucode

LOG_STD_ACTION

IPC-3-ACKSEND

3-Error

sending to [chars]: [chars]

Sending an acknowledgement reply to the specified source failed for the given reason with the likely result that some software on the source will timeout.

cpp-ucode

LOG_STD_ACTION

IPC-3-NOSRC

3-Error

packet from id [dec]

Received an IPC packet from an unrecognized source node with the specified ID.

cpp-ucode

LOG_STD_ACTION

IPC-3-BADSEQ

3-Error

got [dec] expected [dec] from [chars]

-

-

-

IPC-3-TOOBIG

3-Error

message type [dec] length [dec] offset [hec] from [chars]

The length field in an IPC message was found to extend beyond the packet that contained it.

cpp-ucode

LOG_STD_ACTION

IPC-3-TOOSMALL

3-Error

message type [dec] length [dec] offset [hec] from [chars]

The length field in an IPC message was smaller than the IPC msg header length.

cpp-ucode

LOG_STD_ACTION

IPC-3-BADLENGTH

3-Error

IPC length [dec] > received length [dec] to sub device [dec] with fc code [dec]

The length field in an IPC packet was larger than the number of bytes actually in the packet.

cpp-ucode

LOG_STD_ACTION

IPC-3-PROXY_IPC_SEND_FAILED

3-Error

Attempt to send IPC message by [chars] failed with [chars]

Transmission of an IPC message by proxy failed.

cpp-ucode

LOG_STD_ACTION

IPC-3-PROXY_IPC_ALLOC_FAILED

3-Error

Allocate IPC message by [chars] failed - [chars]

Allocation of an IPC packet buffer by proxy failed.

cpp-ucode

LOG_STD_ACTION

IPC-3-CNTALLOC

3-Error

IPC control msg subtype [dec]

Allocating an IPC control message failed.

cpp-ucode

LOG_STD_ACTION

IPC-3-CNTSEND

3-Error

sending ICP msg subtype [dec] to [chars]: [chars]

Sending an ICP control message to the specified source failed for the given reason. Message should will be retried

cpp-ucode

LOG_STD_ACTION

IPC-3-BADRSTATE

3-Error

Received ICP msg state [dec]

Received IPC message while connection not ACTIVE

cpp-ucode

LOG_STD_ACTION

IPC-3-CREATEFAIL

3-Error

IPC CREATE msg failed invalid [chars] [dec]

IPC Create message had invalid parameter

cpp-ucode

LOG_STD_ACTION

IPC-3-INIT_IN_PROGRESS

3-Error

IPC Message received before init complete

Cannot process IPC packet until init stage is complete

-

LOG_STD_ACTION

IPC-7-RECYCLE_HEADER_ALLOC_FAIL

7-Debug

Unable to alloc gpm for recycle header

An IPC message need memory to build recycle header.

cpp-ucode

LOG_STD_ACTION

IPC-7-RECYCLE_TAIL_DROP

7-Debug

Dropping IPC packet due to recycle queue full

An IPC message can't recycled due to queue full.

cpp-ucode

LOG_STD_ACTION

ATTN-2-MBOX_REG_FAIL

2-Critical

return code [dec]

Registration of handler function for mailbox event failed mailbox event failed.

cpp-ucode

LOG_STD_ACTION

ATTN-2-PROXY_INIT_FAIL_IPC_REG

2-Critical

return code [dec]

Initialization of attention proxy failed due to error registering IPC handler function.

cpp-ucode

LOG_STD_ACTION

ATTN-3-PROXY_UNHANDLED_MSG

3-Error

subtype [dec]

Attention proxy received a message with an unknown subtype.

cpp-ucode

LOG_STD_ACTION

ATTN-3-PROXY_IPC_ALLOC_FAILED

3-Error

[chars]

Allocation of an IPC packet buffer by the attention proxy failed.

cpp-ucode

LOG_STD_ACTION

ATTN-3-PROXY_IPC_SEND_FAILED

3-Error

[chars]

Transmission of an IPC message by the attention proxy failed.

cpp-ucode

LOG_STD_ACTION

ATTN-3-SYNC_TIMEOUT

3-Error

msecs since last timeout %llu missing packets [dec]

Attention sync command timed out.

cpp-ucode

LOG_STD_ACTION

CFT_CONGESTION_STATE-6-STATE_DEFAULT

6-Information

CPU-usage regulation parameters have been changed to default. Max back-off timeout:[dec] seconds CPU threshold [dec]%%.

Parameters to default.

cpp-ucode

LOG_STD_ACTION

CFT_CONGESTION_STATE-6-STATE_CHANGED_TO_NORMAL

6-Information

CPU Utilization back to normal CPU usage regulation state is now: Normal.

CFT Congestion state back to normal.

cpp-ucode

LOG_STD_ACTION

CFT_CONGESTION_STATE-4-STATE_CHANGED_TO_SELF_REGULATED

4-Warning

CPU Utilization is high:[dec]%% CPU usage regulation state is now: Self-regulated.

CFT Congestion state changed to Self-regulated.

cpp-ucode

LOG_STD_ACTION

CFT_CONGESTION_STATE-4-STATE_CHANGED_TO_GRADUAL_BRINGUP

4-Warning

CPU Utilization:[dec]%%. CPU usage regulation state is now: Gradual bring-up.

CFT Congestion state changed to Gradual bring-up

cpp-ucode

LOG_STD_ACTION

CFT_CONGESTION_STATE-4-CPU_THRESHOLD_CHANGE

4-Warning

CPU Threshold has been changed to [dec]%%.

CPU threshold has been changed.

cpp-ucode

LOG_STD_ACTION

CFT_CONGESTION_STATE-4-MAX_BACKOFF_CHANGE

4-Warning

Maximum back-off timeout has been changed to [dec].

Maximum back-off timeout has been changed.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-2-DRAM_POOL_CREATE_ERR

2-Critical

return code [dec]

Creation of public DRAM memory pool failed.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-2-SRAM_POOL_CREATE_ERR

2-Critical

return code [dec]

Creation of public SRAM memory pool failed.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-2-DUP_DRAM_POOL_CREATE

2-Critical

pool exists

Request to create public DRAM memory pool failed because pool already exists.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-2-DUP_SRAM_POOL_CREATE

2-Critical

pool exists

Request to create public SRAM memory pool failed because pool already exists.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-POOL_CREATE_PARM_ERR

3-Error

addr 0x[hec] size [dec]

Creation of memory pool failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-POOL_APPEND_PARM_ERR

3-Error

pool handle 0x[hec] addr 0x[hec] size [dec]

Append of additional memory to pool failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-POOL_STATS_PARM_ERR

3-Error

pool handle 0x[hec] stats addr 0x[hec]

Read of memory pool statistics failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-MALLOC_PARM_ERR

3-Error

pool handle 0x[hec] size [dec]

Memory allocation request failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-LOCK_PARM_ERR

3-Error

pool handle 0x[hec] addr 0x[hec]

Request to lock memory pool element failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-FREE_PARM_ERR

3-Error

pool handle 0x[hec] addr 0x[hec]

Memory deallocation request failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-DESTROY_PARM_ERR

3-Error

pool handle 0x[hec]

Request to delete memory pool failed due to bad parameter value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-2-POOL_CORRUPT

2-Critical

pool handle 0x[hec] magic value 0x[hec]

Memory pool data structure has been corrupted.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-2-ELEMENT_CORRUPT

2-Critical

pool handle 0x[hec] addr 0x5x magic value 0x[hec] ref cnt [dec]

Memory element has been corrupted.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-MALLOC_NO_MEM

3-Error

pool handle 0x[hec] size [dec]

Memory pool allocation request failed due to insufficient memory being available.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-LOCK_MAX_REF_CNT

3-Error

pool handle 0x[hec] addr 0x[hec]

Request to lock memory pool element failed due to reference count for element already being at the maximum value.

cpp-ucode

LOG_STD_ACTION

MEM_MGR-3-LOCK_MAX_REF_CNT

3-Error

-

-

-

-

DEAD-4-SCARLET

4-Warning

* Interface [chars]: I knew without asking she was into the blues

-

-

-

DEAD-4-SCARLET

4-Warning

-

-

-

-

-

4-Warning

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

CPP_PKT_SUBBLOCK-3-PKT_SB_MANAGE_FAIL

3-Error

rc=0x[hec]

A packet subblock manage has failed

cpp-ucode

LOG_STD_ACTION

PUNT_INJECT-2-CAUSE_CFG_ERR

2-Critical

[chars] [chars] initialization failed

Initialization of Punt/Inject cause failed due to invalid configuration parameters

cpp-ucode

LOG_STD_ACTION

PUNT_INJECT-3-DROP_POLICY_SKIPPED

3-Error

[chars] cause=[dec] output drop policy skipped

Output drop policy unexpected skipped on punt packet

cpp-ucode

LOG_STD_ACTION

PUNT_INJECT-5-DROP_PUNT_INTF

5-Notice

punt interface policer drop packet from [chars] cause [chars] 0x[hec]

-

-

-

PUNT_INJECT-5-DROP_PUNT_CAUSE

5-Notice

punt policer drops packets cause: [chars] 0x[hec] from [chars] [chars]

-

-

-

PUNT_INJECT-5-DROP_GLOBAL_POLICER

5-Notice

global punt policer drops packet from [chars]

drop punt packet by global punt policer

cpp-ucode

LOG_STD_ACTION

PA_PKT-5-PA_DLIST_ALLOC_FAILED

5-Notice

-

Could not allocate segmented packet list header.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_VFR_CALLBACK_ARGS_ERROR

3-Error

[chars] 0x[hec]

PA vFR callback input args error.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_DLIST_MEM_REQ_FAILED

3-Error

-

Failure occurred when attempting to request segmented packet memory.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_MCST_REPL_DESC_OVERFL

3-Error

[chars]

PA M-Cast Gather descriptor list exceeded limit of 255 entries.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_MCST_GPM_ALLOC_FAILURE

3-Error

[chars]

PA M-Cast replication failed to allocate required GPM.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_MCST_DUP_FAILURE

3-Error

[chars]

PA M-Cast replication failed to allocate duplicate the requisite PA structures.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_PUT_FAILURE

3-Error

[chars]

The PA API layer failed to complete a requested WRITE into pkt memory.

cpp-ucode

LOG_STD_ACTION

PA_PKT-3-PA_ADJUST_FIRST_FRAG_FAILURE

3-Error

[chars]

PA unaware feature doing pkt_head_clip more than first pbuf on PA pkt.

cpp-ucode

LOG_STD_ACTION

IFMAP-3-CAUSE_CFG

3-Error

hash table not initialized

PAL interface handle to uidb hash table not initialized

cpp-ucode

LOG_STD_ACTION

RTREE-3-ALLOC_FAIL

3-Error

aux [hec]

A Radix Tree request has caused an out of memory condition

cpp-ucode

LOG_STD_ACTION

CVLA-3-FEAUTE_HANDLE_INVALID

3-Error

Invalid handle magic 0x[hec] for handle %p

Internal error Feautre handle contains invalid magic

cpp-ucode

LOG_STD_ACTION

UI-6-NOHANDLER

6-Information

module type [dec] subtype [dec]

A UI message was received containing an unrecognized module type or module subtype

cpp-ucode

LOG_STD_ACTION

UI-3-REPLY

3-Error

module type [dec] subtype [dec]

A UI reply message failed in the IPC send. Sender will not get reply

cpp-ucode

LOG_STD_ACTION

UI-3-IPC_ALLOC

3-Error

module type [dec] subtype [dec]

IPC packet allocation failed for UI reply. Sender will not get reply

cpp-ucode

LOG_STD_ACTION

PBUF-3-PBUF_MEM_REQ_FAILED

3-Error

-

Failure occurred when attempting to request extended packet memory.

cpp-ucode

LOG_STD_ACTION

PBUF-3-PBUF_MEM_INIT_FAILED

3-Error

[chars]

Failure occurred when attempting to create memory resource

cpp-ucode

LOG_STD_ACTION

PBUF-3-PBUF_PKT_MEM_CORRUPT

3-Error

[hec] [hec]

Memory corruption detected while freeing extended packet memory

cpp-ucode

LOG_STD_ACTION

PBUF-3-PBUF_SH_DRAM_CVT_FAIL

3-Error

[chars]

An attempt to convert a shared DRAM buffer to non-shared failed.

cpp-ucode

LOG_STD_ACTION

HMR-3-HASH_SIZE_ZERO

3-Error

count [dec] poly [dec]

An invalid hash table size of 0 was detected

cpp-ucode

LOG_STD_ACTION

MBOX-3-REG_FAIL_BAD_PARM

3-Error

event 0x[hec] handler 0x[hec]

Registration of handler function for a mailbox event failed due to a bad parameter.

cpp-ucode

LOG_STD_ACTION

MBOX-3-REG_FAIL_HANDLER_EXISTS

3-Error

event 0x[hec] handler 0x[hec]

Registration of handler function for a mailbox event failed because a handler is already registered for the event.

cpp-ucode

LOG_STD_ACTION

MBOX-3-DEREG_FAIL_BAD_PARM

3-Error

event 0x[hec]

Deregistration of handler function for a mailbox event failed due to a bad parameter.

cpp-ucode

LOG_STD_ACTION

MBOX-3-DEREG_FAIL_NO_HANDLER

3-Error

event 0x[hec] handler 0x[hec]

Deregistration of handler function for a mailbox event failed because no handler was registered for the event.

cpp-ucode

LOG_STD_ACTION

MBOX-3-NO_HANDLER_FOR_EVENT

3-Error

events 0x[hec] bad bit number [dec]

Mailbox event is pending but no handler is registered for event.

cpp-ucode

LOG_STD_ACTION

TIME-3-HB_SEQ_FAIL

3-Error

expected seq_num 0x[hec] rcvd seq_num 0x[hec]

The timer services had exceeded the maximum number of timer heartbeat sequence number errors.

cpp-ucode

LOG_STD_ACTION

TIME-2-TIMESTAMP_BAD_CLOCK

2-Critical

%llu

Unsupported PPE core clock frequency.

cpp-ucode

LOG_STD_ACTION

TIME-2-HB_START_FAILED

2-Critical

timer services failed to start

The timer services could not be started because GPM allocation failed

cpp-ucode

LOG_STD_ACTION

CPP_MPASS-3-INVALID_VECTOR

3-Error

vector [dec]

An invalid multipass vector was received

cpp-ucode

LOG_STD_ACTION

INFRA_ARL-3-BAD_ART_ID

3-Error

art_id=[hec]

An internal error occurred

cpp-ucode

LOG_STD_ACTION

LOGGER-6-DROPPED

6-Information

[dec] messages

Due to a lack of available buffers one or more log messages were dropped.

cpp-ucode

LOG_STD_ACTION

LOGGER-3-ASSERT

3-Error

failure at %08X:[chars]:[dec] [chars]

-

-

-

LOGGER-6-IPC_ALLOC

6-Information

failure

Logger client IPC alloc failed messages were droppped.

cpp-ucode

LOG_STD_ACTION

LOGGER-6-IPC_SEND

6-Information

failure: [chars]

Logger client IPC send failed messages were dropped.

cpp-ucode

LOG_STD_ACTION

LOGGER-3-IPC_INIT

3-Error

failure

Logger client proxy IPC registration failed.

cpp-ucode

LOG_STD_ACTION

LOGGER-3-IPC_UNHANDLED

3-Error

failure

An unknown message was received by the logger client proxy.

cpp-ucode

LOG_STD_ACTION

DROP-3-RESERVED

3-Error

[chars]

An invalid drop cause was passed to the drop infrastructure.

cpp-ucode

LOG_STD_ACTION

DROP-3-DOUBLE_DROP

3-Error

First drop error cause [dec] update stat cause [dec] trace: [hec] [hec]

The drop infrastructure was called for a packet that was previously dropped.

cpp-ucode

LOG_STD_ACTION

MX-6-NOMEM

6-Information

[chars] bufhdr allocation failure

An attempt to allocate memory failed. This could cause features that manage packets in multiple pieces or that directly export data not to work properly in some cases.

cpp-ucode

LOG_STD_ACTION

MX-3-CARVE

3-Error

[chars]: size [dec] too small

A software error resulted in an attempt to create buffers in an area of memory that was too small.

cpp-ucode

LOG_STD_ACTION

MX-3-RESIZE

3-Error

[chars]: non-contiguous resize: orig [hec]/[hec] new [hec]/[hec]

A software error was detected during a resize operation on the specified memory region.

cpp-ucode

LOG_STD_ACTION

MX-6-NOBUFHDR

6-Information

[chars]

An attempt to add buffers within a memory region failed.

cpp-ucode

LOG_STD_ACTION

MX-3-MAXPOOLS

3-Error

too low

A source code inconsistency was detected.

cpp-ucode

"Increase the number of pools allowed."

MX-3-INITBUFHDR

3-Error

[chars]: mgmt memory allocation failure size [dec]

insufficient mgmt memory provided for initialization of the external memory manager which will cause features that manage packets in multiple pieces or that directly export data not to work properly.

cpp-ucode

LOG_STD_ACTION

MX-3-BADSTART

3-Error

[chars]: [hec] current [hec] size [dec]

A software error was detected during an attempt to increase the size of an external memory region.

cpp-ucode

LOG_STD_ACTION

MX-3-BADPOOL

3-Error

[chars]: [dec]

Software detected the use of an invalid pool index which may be the result of incompatible software versions on different system components.

cpp-ucode

LOG_STD_ACTION

MX-3-BADFEAT

3-Error

[chars]: [dec]

Software detected the use of an invalid feature enumeration which may be the result of incompatible software versions on different system components.

cpp-ucode

LOG_STD_ACTION

MX-3-BADMAGIC

3-Error

[chars]: %04x in [hec]

A data structure inconsistency was detected in a buffer header perhaps as the result of memory corruption. A buffer has been dropped because of this resulting in a memory leak and potential system unreliability.

cpp-ucode

"Please report the problem Cisco technical support along with the " "text of the error message. " "If the system becomes unstable restarting or reloading the affected " "component should correct the instability."

MX-3-SUBRGNINDX

3-Error

[chars]: Subregion Index allocation failure

Unable to obtain a sub region index so unable add sw managed memory

cpp-ucode

LOG_STD_ACTION

MSG_FIFO-2-MSG_FIFO_CREATE

2-Critical

[chars]: Bad parameter to message fifo creaate [chars] = 0x%08x

Failed to create message fifo invalid memory size or other parameter.

cpp-ucode

LOG_STD_ACTION

PACTRAC-3-BIG_SERIAL

3-Error

serial number [dec] exceeds configured packets [dec]

A packet serial number was encountered that was larger than than the configured number of packets being traced.

iosxe-pactrac

LOG_STD_PACTRAC_ACTION

PACTRAC-3-POOL_FULL

3-Error

unable to return serial number [dec] to pool

The serial number could not be returned to the serial number pool because the pool is full most likely because a serial number has been returned multiple times.

iosxe-pactrac

LOG_STD_PACTRAC_ACTION

PACTRAC-3-NUM_WRITES

3-Error

attempt to write [dec] bytes of path data for id [dec]

The serial number could not be returned to the serial number pool because the pool is full most likely because a serial number has been returned multiple times.

iosxe-pactrac

LOG_STD_PACTRAC_ACTION

PACTRAC-3-INVALID_PARM

3-Error

encountered invalid parameter

An invalid parameter was encountered during packet-trace processing.

iosxe-pactrac

"Copy the error message exactly as it appears on the console or in the ""system log. Research and attempt to resolve the error using the ""Output Interpreter " OUTPUT_INTERPRETER ". Also perform a ""search of the Bug Toolkit " BUG_TOOLKIT ". If you still require ""assistance open a case with the Technical Assistance Center via the ""Internet " TAC_CASE_OPEN " or contact your Cisco technical support ""representative and provide the representative with the gathered information."

PKTLOG-3-PROXY_IPC_SEND_FAILED

3-Error

[chars] [chars]

Transmission of an IPC message by the packet logger proxy failed.

cpp-ucode

LOG_STD_ACTION

PKTLOG-3-PROXY_IPC_ALLOC_FAILED

3-Error

[chars]

Allocation of an IPC packet buffer by the packet logger proxy failed.

cpp-ucode

LOG_STD_ACTION

PKTLOG-3-PROXY_BAD_SUBTYPE

3-Error

[dec]

Invalid subtype was passed to packet logger proxy IPC handler.

cpp-ucode

LOG_STD_ACTION

PKTLOG-2-PROXY_IPC_SET_FAILED

2-Critical

[chars]

Packet logger proxy IPC handler could not be initialized.

cpp-ucode

LOG_STD_ACTION

PKTLOG-4-PROXY_DUP_INIT

4-Warning

[chars]

Duplicate initialization IPC message received for user [dec] client id [dec].

cpp-ucode

LOG_STD_ACTION

PKTLOG-3-PKTLOG_IPC_SEND_FAILED

3-Error

[chars] [chars]

Transmission of an IPC message by the packet logger failed. ACL and stats lost.

cpp-ucode

LOG_STD_ACTION

PKTLOG-4-PKTLOG_IPC_ALLOC_FAILED

4-Warning

[chars]

Allocation of an IPC packet buffer by the packet logger failed.

cpp-ucode

LOG_STD_ACTION

PKTLOG-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length.

cpp-ucode

LOG_STD_ACTION

PKTLOG-4-PROXY_INVALID_USER_IDX

4-Warning

[dec] [dec]

IPC message contained invalid user index for client id.

cpp-ucode

LOG_STD_ACTION

PKTLOG-1-PROXY_MEM_RET_ERR

1-Alert

[chars] [dec] [dec] [dec]

IPC failed and could not return memory

cpp-ucode

LOG_STD_ACTION

PKTLOG-1-PROXY_MEM_APPEND_ERR

1-Alert

[dec] [dec] [dec]

An invalid memory chunk magic was detected in a memory chunk element

cpp-ucode

LOG_STD_ACTION

CHUNK-3-INVALID_ELEM_SIZE

3-Error

requested [dec]

Memory corruption was detected by the memory chunk manager

cpp-ucode

LOG_STD_ACTION

CHUNK-3-CHUNK_BAD_REFCNT

3-Error

refcnt=[dec] data=0x[hec]

The memory chunk manager detected a bad reference count

cpp-ucode

LOG_STD_ACTION

CHUNK-3-SIBLING_ERR

3-Error

Tried to destroy sibling memory chunk 0x[hec]

An invalid sibling condition was hit in the Memory Chunk Manager

cpp-ucode

LOG_STD_ACTION

PKT_MANIP-3-ALLOC_FAIL

3-Error

retcode [dec]

A critical failure occurred when trying to obtain packet memory

cpp-ucode

LOG_STD_ACTION

BFD_PROXY-3-BFD_MEM_REQ_FAILED

3-Error

BFD IPC subtype: [dec]

Requesting more memory failed.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-3-BFD_MEM_EXTEND_FAILED

3-Error

BFD IPC subtype: [dec]

Extending memory failed.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP BFD Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP BFD Proxy received invalid IPC message length from control plane. This message will be ignored.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP BFD Proxy received invalid message type [dec]

Cisco internal software error. QFP BFD Proxy received an invalid message from control plane. This message will be ignored.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP BFD Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP BFD Proxy initialization detected that the IPC interface initialization failed. QFP BFD proxy will not be functional while this condition exists.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-3-PROXY_BAD_MSG

3-Error

QFP BFD Proxy received bad length message type [dec]

Cisco internal software error. QFP BFD Proxy received a corrupted message from control plane. This message will be ignored.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP BFD Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP BFD Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

BFD_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP BFD Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP BFD Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

asr1k-bfd keyword:bfd

LOG_STD_ACTION

L2BD_PROXY-3-L2BD_MEM_REQ_FAILED

3-Error

L2BD IPC subtype: [dec]

Requesting more memory failed.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-3-L2BD_MEM_EXTEND_FAILED

3-Error

L2BD IPC subtype: [dec]

Extending memory failed.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP L2BD Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP L2BD Proxy received invalid IPC message length from control plane. This message will be ignored.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP L2BD Proxy received invalid message type [dec]

Cisco internal software error. QFP L2BD Proxy received an invalid message from control plane. This message will be ignored.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP L2BD Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP L2BD Proxy initialization detected that the IPC interface initialization failed. QFP L2BD proxy will not be functional while this condition exists.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-3-PROXY_BAD_MSG

3-Error

QFP L2BD Proxy received bad length message type [dec]

Cisco internal software error. QFP L2BD Proxy received a corrupted message from control plane. This message will be ignored.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP L2BD Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP L2BD Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

L2BD_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP L2BD Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP L2BD Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-l2bd keyword:l2bd

LOG_STD_ACTION

CPP_NAT66_PROXY-3-NAT66_IPC_FAIL

3-Error

rc= [dec]

The NAT66 proxy has received an IPC with an unexpected format/data

cpp-ucode

LOG_STD_ACTION

CPP_NAT66_PROXY-3-INVALID_IPC_SUBTYPE

3-Error

subtype is [dec]

The NAT66 proxy has received an IPC with an unexpected subtype

cpp-ucode

LOG_STD_ACTION

CPP_NAT66_PROXY-3-NAT66_INIT_FAIL

3-Error

nat66 init failure rc= [dec]

The NAT proxy has experienced a failure when trying to initialize the NAT66 proxy

cpp-ucode

LOG_STD_ACTION

ALG_PROXY-3-PROXY_MEM_REQ_FAILED

3-Error

ALG IPC subtype: [dec]

Requesting more memory failed.

cpp-ucode

LOG_STD_ACTION

ALG_PROXY-3-PROXY_MEM_EXTEND_FAILED

3-Error

ALG IPC subtype: [dec]

Extending memory failed.

cpp-ucode

LOG_STD_ACTION

ALG_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length.

cpp-ucode

LOG_STD_ACTION

ALG_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[dec]

Invalid IPC message subtype.

cpp-ucode

LOG_STD_ACTION

ALG_PROXY-3-PROXY_IPC_FAIL

3-Error

rc= [dec]

The ALG proxy has experienced a failure when trying to send an IPC

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MEM_REQ_FAILED

3-Error

SDWAN IPC subtype: [dec]

Requesting more memory failed.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MEM_EXTEND_FAILED

3-Error

SDWAN IPC subtype: [dec]

Extending memory failed.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP SDWAN Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP SDWAN Proxy received invalid IPC message length from control plane. This message will be ignored.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP SDWAN Proxy received invalid message type [dec]

Cisco internal software error. QFP SDWAN Proxy received an invalid message from control plane. This message will be ignored.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP SDWAN Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP SDWAN Proxy initialization detected that the IPC interface initialization failed. QFP SDWAN proxy will not be functional while this condition exists.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-3-PROXY_BAD_MSG

3-Error

QFP SDWAN Proxy received bad length message type [dec]

Cisco internal software error. QFP SDWAN Proxy received a corrupted message from control plane. This message will be ignored.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP SDWAN Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP SDWAN Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP SDWAN Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP SDWAN Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-sdwan keyword:sdwan

LOG_STD_ACTION

SDWAN_PROXY-2-SDWAN_MSG_PROXYINIT_FAILURE

2-Critical

SDWAN - Failed to register IPC message handler result code [dec]

QFP SDWAN feature failed to register an IPC message handler for communication with control plane. This will cause the featue not to function.

SDWAN_COMP_NAME

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MSG_PROXY_UNKNOWN_IPCMSG

3-Error

SDWAN - Received an unknown type code [dec] IPC message

QFP SDWAN feature received an unknown message from another layer of SDWAN feature's software stack.

SDWAN_COMP_NAME

LOG_STD_RECUR_ACTION

SDWAN_PROXY-3-SDWAN_MSG_PROXY_INVALID_MSGLEN

3-Error

SDWAN - Received an invalid length IPC message

QFP SDWAN feature received an incorrect length of IPC message from anoter layer of SDWAN feature's software stack m_enum [dec] m_subtype [dec] m_len [dec] m_flags 0x[hec] m_source [dec].

SDWAN_COMP_NAME

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MSG_PROXY_ALLOC_FAILURE

3-Error

SDWAN - Failed to get [dec] bytes space for IPC reply message

QFP ET-Anallytics feature detected buffer allocation failure while sending reply to a message from another layer of SDWAN feature's software stack.

SDWAN_COMP_NAME

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MSG_PROXY_OPENREPLY_FAIL

3-Error

SDWAN - Failed to open reply message part of IPC packet

QFP SDWAN feature failed to open message part of IPC packet while sending a reply to another layer of SDWAN feature's software stack.

SDWAN_COMP_NAME

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MSG_PROXY_IPCSEND_FAIL

3-Error

SDWAN - Failed to send IPC message result code [dec]

QFP SDWAN feature failed to send IPC message to another layer of SDWAN feature's software stack.

SDWAN_COMP_NAME

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_MSG_PROXY_DEBUG_REG_FAILED

3-Error

-

SDWAN Conditional Debugging Registration failed.

SDWAN_COMP_NAME

LOG_STD_ACTION

SDWAN_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid SDWAN IPC message length.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_CREATE_FAILED

3-Error

-

SDWAN HSL creation failed.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_ADD_DEST_FAILED

3-Error

-

SDWAN HSL add destination failed.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_BIND_FAILED

3-Error

-

SDWAN HSL bind failed.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_PRE_SEND_HANDLER_FAILED

3-Error

-

SDWAN HSL pre send handler registration failed.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_BIND_TEMPLATE_FAILED

3-Error

[dec]

SDWAN HSL bind tempalte failed at given index.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_ENABLE_FAILED

3-Error

-

SDWAN HSL enable failed.

cpp-ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_MOD_DEST_FAILED

3-Error

-

SDWAN HSL modify destination failed.

cpp_ucode

LOG_STD_ACTION

SDWAN_PROXY-3-SDWAN_PROXY_HSL_MOD_CFG_FAILED

3-Error

-

SDWAN HSL modify configuration failed. Currently only support rec_timeout

cpp_ucode

LOG_STD_ACTION

CPP_PFR_PROXY-3-INVALID_IPC_SUBTYPE

3-Error

subtype is [dec]

The PfR proxy has receive an IPC with an unexpected subtype

cpp-ucode

LOG_STD_ACTION

CPP_PFR_PROXY-3-PFR_INIT_FAIL

3-Error

pfr init failure rc= [dec]

The PFR proxy has experienced a failure when trying to init PFR

cpp-ucode

LOG_STD_ACTION

CPP_PFR_PROXY-3-PFR_IPC_PAK_ALLOC_FAILED

3-Error

rc= [dec]

Allocation of PFR IPC response pkt failed

cpp-ucode

LOG_STD_ACTION

CPP_PFR_PROXY-3-PFR_SEND_IPC_FAIL

3-Error

rc= [dec]

The PfR proxy has experienced a failure when trying to send an IPC

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-3-PROXY_IPC_ADJ_ID_HASH_FAILED

3-Error

-

Getting Hash Address failed.

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-3-PROXY_IPC_OCE_CHAIN_PTR_FAILED

3-Error

[hec]

Null OCE Chain pointer.

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-3-PROXY_IPC_PACKET_ALLOCATION_FAILED

3-Error

[hec]

Failed to allocate packet buffer for IPC

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-3-PROXY_IPC_PACKET_SEND_FAILED

3-Error

[hec]

Failed to send IPC packet.

cpp-ucode

LOG_STD_ACTION

CEF_PROXY-3-PROXY_IPC_ADJ_IDX_FAILED

3-Error

[hec]

Failed to get adjacency index from IPC packet.

cpp-ucode

LOG_STD_ACTION

DPSS-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper DPSS software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-dpss

"This is normally a software issue. " LOG_STD_RECUR_ACTION

DPSS-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper DPSS software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-dpss

"This is normally a software issue. " LOG_STD_RECUR_ACTION

DPSS-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the DPSS feature failed. This will cause the feature to not function.

qfp-dpss

"This is normally a software issue. " "The consequences are that the DPSS feature will not function. " LOG_STD_ACTION

UTD-3-IPC_INVALID_MSG

3-Error

UTD-Invalid request [dec]

We received an invalid message from another layer of the UTD software stack.

qfp-utd

LOG_STD_RECUR_ACTION

UTD-3-FEAT_DOWN

3-Error

UTD-Invalid request [chars] [dec] while feature is down

While the feature was not active an invalid request was received from another layer of the UTD software stack.

qfp-utd

LOG_STD_RECUR_ACTION

UTD-3-FEAT_CTX_DOWN

3-Error

UTD-Invalid request [chars] [dec] while context is down

While the feature context was not active an invalid request was received from another layer of the UTD software stack.

qfp-utd

LOG_STD_RECUR_ACTION

UTD-3-IPC_OPEN_REPLY

3-Error

UTD-IPC Open Reply failed request [dec]

For a request from upper UTD software stack layers it was not possible to open the reply buffer.

qfp-utd

"This is normally a software issue. " LOG_STD_RECUR_ACTION

UTD-3-IPC_NORES

3-Error

UTD-No space for the IPC reply size [dec] request [dec]

For a request from upper UTD software stack layers it was not possible to allocate space for a reply for the specified size.

qfp-utd

LOG_STD_RECUR_ACTION

UTD-3-IPC_INVALID_MSG_LEN

3-Error

UTD-Invalid IPC length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length

qfp-utd

LOG_STD_ACTION

UTD-3-IPC_SEND_FAILED

3-Error

UTD-IPC [chars] [dec] send failed [dec]

IPC message send failure

qfp-utd

LOG_STD_ACTION

UTD-2-IPC_INIT_FAILED

2-Critical

UTD-IPC message handler registration failure rc [dec]

Registering an IPC message handler for the UTD feature failed. This will cause the feature to not function.

qfp-utd

LOG_STD_ACTION

UTD-2-IPC_FAILURE

2-Critical

UTD-IPC message [chars] handler failed rc [dec]

An IPC message handler for the UTD feature failed. This will cause the feature to not function.

qfp-utd

LOG_STD_ACTION

UTD-3-PROXY_HSL_BIND_TEMPLATE_FAILED

3-Error

[dec]

HSL bind template failed at given index.

qfp-utd

LOG_STD_ACTION

UTD-3-PROXY_HSL_CREATE_FAILED

3-Error

-

HSL creation failed.

qfp-utd

LOG_STD_ACTION

UTD-3-PROXY_HSL_ADD_DEST_FAILED

3-Error

-

HSL adding export destination failed.

qfp-utd

LOG_STD_ACTION

UTD-3-PROXY_HSL_BIND_FAILED

3-Error

-

HSL binding to session failed.

-

LOG_STD_ACTION

CONF_SW-3-FEAT_DOWN

3-Error

Invalid request [chars] while feature down conf id [dec]

While the feature was not active an invalid request was received from another layer of the CONF_SW software stack for the specified conf ID. Some requests do not have an associated conf ID. For them the displayed conf ID is zero.

cpp-conf-sw

"This is a software issue. The consequences " "could be limited to only one or a few confs. " LOG_STD_RECUR_ACTION

CONF_SW-3-FEAT_UP

3-Error

Invalid request [chars] while feature up

While the feature was active an invalid request was received from another layer of the CONF SW software stack.

cpp-conf-sw

"This is a software issue. " "There are no consequences as this can only have been an Init request " "while the feature was already active. " LOG_STD_RECUR_ACTION

CONF_SW-3-NO_RES

3-Error

[chars] resource not available for the [chars] request conf id [dec]

The specified software resource was not available or could not be located for the specified request from upper CONF SW software stack layers for the specified conf ID.

cpp-conf-sw

"This is a software issue. The consequences " "are that the specified request could not be performed. " LOG_STD_RECUR_ACTION

CONF_SW-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper CONF SW software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck conf that cannot be established etc. In rare cases this could also affect other operations such as feature activation deactivation modification High-Availability switchover operations.

cpp-conf-sw

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CONF_SW-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper CONF SW software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck conf that cannot be established etc. In rare cases this could also affect other operations such as feature activation deactivation modification High-Availability switchover operations.

cpp-conf-sw

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CONF_SW-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CONF SW feature failed. This will cause the feature not to function. The function

cpp-conf-sw

"This is normally a software issue. " "The consequences are that the CONF SW feature will not function. " LOG_STD_ACTION

CWS-3-IPC_INVALID_MSG

3-Error

CWS-Invalid request [dec]

Received Invalid message from CWS client proxy

cws-xe

LOG_STD_RECUR_ACTION

CWS-3-IPC_OPEN_REPLY

3-Error

CWS-IPC Open Reply failed request [chars]

For a request from CWS client proxy opening the reply buffer failed

cws-xe

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CWS-3-IPC_NORES

3-Error

CWS-No space for the IPC reply size [dec] request [chars]

For a request from CWS client proxy it was not possible to allocate space for a reply for the specified size.

cws-xe

LOG_STD_RECUR_ACTION

CWS-3-IPC_SEND_FAILED

3-Error

CWS-IPC [chars] [chars] send failed [dec]

IPC message send failure

cws-xe

LOG_STD_ACTION

CWS-2-IPC_INIT_FAILED

2-Critical

CWS-IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CWS feature failed. This will cause the feature to not function.

cws-xe

LOG_STD_ACTION

IPV4_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_INIT_FAILED

3-Error

-

Initialization of fragment information pool failed.

cpp-ucode

LOG_STD_ACTION

IPV4_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_EXTEND_FAILED

3-Error

-

Increasing of fragment information pool failed.

cpp-ucode

LOG_STD_ACTION

IPV4_REASS_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

IPV4_REASS_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

FRAG_DESC_PROXY-3-PROXY_IPC_FRAG_MEM_INIT_FAILED

3-Error

-

Initialization of fragment descriptor pool failed.

cpp-ucode

LOG_STD_ACTION

FRAG_DESC_PROXY-3-PROXY_IPC_VFR_MEM_INIT_FAILED

3-Error

-

Initialization of vFR state pool failed.

cpp-ucode

LOG_STD_ACTION

FRAG_DESC_PROXY-3-PROXY_IPC_FRAG_MEM_EXTEND_FAILED

3-Error

-

Increasing of fragment descriptor pool failed.

cpp-ucode

LOG_STD_ACTION

FRAG_DESC_PROXY-3-PROXY_IPC_VFR_MEM_EXTEND_FAILED

3-Error

-

Increasing of vFR state pool failed.

cpp-ucode

LOG_STD_ACTION

FRAG_DESC_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Invalid IPC message subtype.

cpp-ucode

LOG_STD_ACTION

FRAG_DESC_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

ETHERNET_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

CPP ETHERNET Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. CPP ETHERNET Proxy initialization detected that the IPC interface initialization failed. CPP ETHERNET proxy will not be functional while this condition exists.

qfp-bb keyword:none

LOG_STD_ACTION

ETHERNET_PROXY-3-PROXY_BAD_MSG

3-Error

CPP ETHERNET Proxy received bad length message type [dec]

Cisco internal software error. CPP ETHERNET Proxy received a corrupted message from control plane. This message will be ignored.

qfp-bb keyword:none

LOG_STD_ACTION

ETHERNET_PROXY-3-PROXY_INV_MSG

3-Error

CPP ETHERNET Proxy received invalid message type [dec]

Cisco internal software error. CPP ETHERNET Proxy received an invalid message type from control plane. This message will be ignored.

qfp-bb keyword:none

LOG_STD_ACTION

ETHERNET_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

CPP ETHERNET Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. CPP ETHERNET Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-bb keyword:none

LOG_STD_ACTION

ETHERNET_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

CPP ETHERNET Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. CPP ETHERNET Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-bb keyword:none

LOG_STD_ACTION

ETHERNET_PROXY-3-PROXY_IPC_NO_HDLR

3-Error

CPP ETHERNET Proxy received unregistered message type [dec]

Cisco internal software error. CPP ETHERNET Proxy received a message from control plane but there is no registered handler. The message is lost as the result of this condition.

qfp-bb keyword:none

LOG_STD_ACTION

SDVT-3-IPC_INVALID_MSG

3-Error

SDVT-Invalid request [dec]

We received an invalid message from another layer of the SDVT software stack.

cedge-appqoe

LOG_STD_RECUR_ACTION

SDVT-3-FEAT_DOWN

3-Error

SDVT-Invalid request [chars] [dec] while feature is down

While the feature was not active an invalid request was received from another layer of the SDVT software stack.

cedge-appqoe

LOG_STD_RECUR_ACTION

SDVT-3-IPC_OPEN_REPLY

3-Error

SDVT-IPC Open Reply failed request [dec]

For a request from upper SDVT software stack layers it was not possible to open the reply buffer.

cedge-appqoe

"This is normally a software issue. " LOG_STD_RECUR_ACTION

SDVT-3-IPC_NORES

3-Error

SDVT-No space for the IPC reply size [dec] request [dec]

For a request from upper SDVT software stack layers it was not possible to allocate space for a reply for the specified size.

cedge-appqoe

LOG_STD_RECUR_ACTION

SDVT-3-IPC_INVALID_MSG_LEN

3-Error

SDVT-Invalid IPC length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length

cedge-appqoe

LOG_STD_ACTION

SDVT-3-IPC_SEND_FAILED

3-Error

SDVT-IPC [chars] [dec] send failed [dec]

IPC message send failure

cedge-appqoe

LOG_STD_ACTION

SDVT-2-IPC_INIT_FAILED

2-Critical

SDVT-IPC message handler registration failure rc [dec]

Registering an IPC message handler for the SDVT feature failed. This will cause the feature to not function.

cedge-appqoe

LOG_STD_ACTION

SDVT-2-IPC_FAILURE

2-Critical

SDVT-IPC message [chars] handler failed rc [dec]

An IPC message handler for the SDVT feature failed. This will cause the feature to not function.

cedge-appqoe

LOG_STD_ACTION

NWPI_PROXY-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper NWPI software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

NWPI_COMP_NAME

"This is normally a software issue. " LOG_STD_RECUR_ACTION

NWPI_PROXY-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the NWPI feature failed. This will cause the feature to not function.

NWPI_COMP_NAME

"This is normally a software issue. " "The consequences are that the NWPI feature will not function. " LOG_STD_ACTION

NWPI_PROXY-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper NWPI software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

NWPI_COMP_NAME

"This is normally a software issue. " LOG_STD_RECUR_ACTION

NWPI_PROXY-3-IPC_ALLOC_FAILED

3-Error

CPP NWPI Proxy [chars] message lost due to message buffer allocation failure.

Proxy internal software error. QFP NWPI Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

NWPI_COMP_NAME

"This is normally a software issue. " LOG_STD_RECUR_ACTION

NWPI_PROXY-3-IPC_SEND_FAILED

3-Error

QFP NWPI Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP NWPI Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

NWPI_COMP_NAME

"This is normally a software issue. " LOG_STD_RECUR_ACTION

WLCLIENT_IPSG_PROXY-3-WLS_IPSG_MEM_REQ_FAILED

3-Error

WLCLIENT IPSG IPC subtype: [dec]

Requesting more memory failed.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-3-WLS_IPSG_MEM_EXTEND_FAILED

3-Error

WLCLIENT IPSG IPC subtype: [dec]

Extending memory failed.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP WLCLIENT IPSG Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP WLCLIENT IPSG Proxy received invalid IPC message length from control plane. This message will be ignored.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP WLCLIENT IPSG Proxy received invalid message type [dec]

Cisco internal software error. QFP WLCLIENT IPSG Proxy received an invalid message from control plane. This message will be ignored.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP WLCLIENT IPSG Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP WLCLIENT IPSG Proxy initialization detected that the IPC interface initialization failed. QFP WLCLIENT IPSG proxy will not be functional while this condition exists.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-3-PROXY_BAD_MSG

3-Error

QFP WLCLIENT IPSG Proxy received bad length message type [dec]

Cisco internal software error. QFP WLCLIENT IPSG Proxy received a corrupted message from control plane. This message will be ignored.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP WLCLIENT IPSG Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP WLCLIENT IPSG Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-swport keyword:swport

LOG_STD_ACTION

WLCLIENT_IPSG_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP WLCLIENT IPSG Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP WLCLIENT IPSG Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-swport keyword:swport

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_SCB_MEM_INIT_FAILED

3-Error

-

Initialization of session control block pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_ICMP_ERROR_MEM_INIT_FAILED

3-Error

-

Initialization of ICMP Error control block pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_SCB_MEM_EXTEND_FAILED

3-Error

-

Increasing of session control block pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_ICMP_ERROR_MEM_EXTEND_FAILED

3-Error

-

Increasing of ICMP Error pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HA_MEM_INIT_FAILED

3-Error

-

Initialization of ha retry pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HA_MEM_EXTEND_FAILED

3-Error

-

Increasing of ha retry pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HOSTDB_MEM_INIT_FAILED

3-Error

-

Initialization of host database pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HOSTDB_MEM_EXTEND_FAILED

3-Error

-

Increasing of host database pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_TEARDOWN_MEM_INIT_FAILED

3-Error

-

Initialization of teardown pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_TEARDOWN_MEM_EXTEND_FAILED

3-Error

-

Increasing of teardown pool failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_FWALL_INIT_FAILED

3-Error

[dec]

Firewall initialization failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_INIT_FAILED

3-Error

[chars] [dec]

IPC failed to reply for firewall initialization status.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_FAILED

3-Error

[chars] [dec]

IPC message allocation for firewall failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_TBL_INIT_FAILED

3-Error

[chars]

Failed to initialize table.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_STATS_FAILED

3-Error

[dec]

IPC send failed to reply for firewall status.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_SESSION_FAILED

3-Error

[dec]

IPC send failed to reply for firewall session query.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_CLEAR_FAILED

3-Error

[dec]

IPC send failed to reply for firewall session clear.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_DEBUG_FAILED

3-Error

[dec]

IPC send failed to reply for firewall session debug.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_SCB_QUERY_FAILED

3-Error

[dec]

IPC send failed to reply for firewall scb query.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Invalid IPC message subtype.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

[dec]

IPC allocation failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

[dec]:[chars]

IPC send failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_CREATE_FAILED

3-Error

-

HSL creation failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_ADD_DEST_FAILED

3-Error

-

HSL add destination failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_BIND_FAILED

3-Error

-

HSL bind failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_ENABLE_FAILED

3-Error

-

HSL enable failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_BIND_TEMPLATE_FAILED

3-Error

[dec]

HSL bind tempalte failed at given index.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-4-PROXY_HSL_ALREADY_INIT

4-Warning

-

HSL logger already initialized

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-4-PROXY_HSL_NOT_INIT

4-Warning

[dec]

HSL logger not initialized

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_MODIFY_FAILED

3-Error

-

HSL modification failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_HSL_MODIFY_DEST_FAILED

3-Error

-

HSL modify destination failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-4-PROXY_IPC_UNINIT_POOL_FAILED

4-Warning

[chars]: [dec]

Could not destroy chunk pool

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-4-PROXY_UNINIT_SESSIONS

4-Warning

in use [dec] [dec]

Not all sessions freed

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_IPC_ERM_CONF_CHANGE_FAILED

3-Error

[dec]

FW IPC send failed to reply for event rate monitoring configuration change.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_DEBUG_REG_FAILED

3-Error

[dec]

FW Conditional Debugging registration failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_FWALL_VFR_REG_FAILED

3-Error

[chars] err: [dec]

FW VFR registration failed.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_FWALL_FBD_NOT_ENABLED

3-Error

FBD Not enabled.. cannot initialize data plane.

Mismatch in FBD capabiities between client and data plane. Coding error.

cpp-ucode

LOG_STD_ACTION

FWALL_PROXY-3-PROXY_FWALL_DOUBLE_INIT

3-Error

Data plane double initialization request.

Coding error - second attempt to initialize data plane.

cpp-ucode

LOG_STD_ACTION

WLS_FQDN_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

WLS_FQDN_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

EPBR_PROXY-2-EPBR_MSG_PROXYINIT_FAILURE

2-Critical

EPBR - Failed to register IPC message handler result code [dec]

QFP EPBR feature failed to register an IPC message handler for communication with control plane. This will cause the featue not to function.

EPBR_COMP_NAME

LOG_STD_ACTION

EPBR_PROXY-3-EPBR_MSG_PROXY_UNKNOWN_IPCMSG

3-Error

EPBR - Received an unknown type code [dec] IPC message

QFP EPBR feature received an unknown message from another layer of EPBR feature's software stack.

EPBR_COMP_NAME

LOG_STD_RECUR_ACTION

EPBR_PROXY-3-EPBR_MSG_PROXY_INVALID_MSGLEN

3-Error

EPBR - Received an invalid length IPC message

QFP EPBR feature received an incorrect length of IPC message from anoter layer of EPBR feature's software stack m_enum [dec] m_subtype [dec] m_len [dec] m_flags 0x[hec] m_source [dec].

EPBR_COMP_NAME

LOG_STD_ACTION

EPBR_PROXY-3-EPBR_MSG_PROXY_ALLOC_FAILURE

3-Error

EPBR - Failed to get [dec] bytes space for IPC reply message

QFP ET-Anallytics feature detected buffer allocation failure while sending reply to a message from another layer of EPBR feature's software stack.

EPBR_COMP_NAME

LOG_STD_ACTION

EPBR_PROXY-3-EPBR_MSG_PROXY_OPENREPLY_FAIL

3-Error

EPBR - Failed to open reply message part of IPC packet

QFP EPBR feature failed to open message part of IPC packet while sending a reply to another layer of EPBR feature's software stack.

EPBR_COMP_NAME

LOG_STD_ACTION

EPBR_PROXY-3-EPBR_MSG_PROXY_IPCSEND_FAIL

3-Error

EPBR - Failed to send IPC message result code [dec]

QFP EPBR feature failed to send IPC message to another layer of EPBR feature's software stack.

EPBR_COMP_NAME

LOG_STD_ACTION

EPBR_PROXY-3-EPBR_MSG_PROXY_DEBUG_REG_FAILED

3-Error

-

EPBR Conditional Debugging Registration failed.

EPBR_COMP_NAME

LOG_STD_ACTION

EPBR_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid EPBR IPC message length.

cpp-ucode

LOG_STD_ACTION

CRYPTO_DEV_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP Crypto device Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP Crypto device Proxy initialization detected that the IPC interface initialization failed. QFP Crypto device proxy will not be functional while this condition exists.

qfp-ipsec keyword:none

LOG_STD_ACTION

CRYPTO_DEV_PROXY-2-PROXY_REG_NULL_MSG_HNDLR

2-Critical

QFP Crypto device Proxy registered invalid message handlers source: [chars].

Cisco internal software error. QFP Crypto device Proxy registered with invalid message handler. QFP Crypto device Proxy will not be functional while this condition exists.

qfp-ipsec keyword:none

LOG_STD_ACTION

CRYPTO_DEV_PROXY-3-PROXY_BAD_MSG

3-Error

QFP Crypto device Proxy received bad length message type [dec]

Cisco internal software error. QFP Crypto device Proxy received a corrupted message from control plane. This message will be ignored.

qfp-ipsec keyword:none

LOG_STD_ACTION

CRYPTO_DEV_PROXY-3-PROXY_INV_MSG

3-Error

QFP Crypto device Proxy received invalid message type [dec]

Cisco internal software error. QFP Crypto device Proxy received an invalid message from control plane. This message will be ignored.

qfp-ipsec keyword:none

LOG_STD_ACTION

CRYPTO_DEV_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP Crypto device Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP Crypto device Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-ipsec keyword:none

LOG_STD_ACTION

CRYPTO_DEV_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP Crypto device Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP Crypto device Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-ipsec keyword:none

LOG_STD_ACTION

GEO_PROXY-3-PROXY_DEBUG_REG_FAILED

3-Error

-

GEO Conditional Debugging registration failed.

cpp-ucode

LOG_STD_ACTION

CPP_WPAN_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

CPP_WPAN_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

CPP_WPAN_PROXY-3-PROXY_IPC_PACKET_ALLOCATION_FAILED

3-Error

[hec]

Failed to allocate packet buffer for IPC

cpp-ucode

LOG_STD_ACTION

CPP_WPAN_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

[hec]

Failed to send IPC packet.

cpp-ucode

LOG_STD_ACTION

CTS_PD-3-IPC_INVALID_MSG

3-Error

CTS-Invalid request [dec]

We received an invalid message from another layer of the CTS software stack.

asr1k-cts

LOG_STD_RECUR_ACTION

CTS_PD-3-FEAT_DOWN

3-Error

CTS-Invalid request [chars] [dec] while feature is down

While the feature was not active an invalid request was received from another layer of the CTS software stack.

asr1k-cts

LOG_STD_RECUR_ACTION

CTS_PD-3-FEAT_CTX_DOWN

3-Error

CTS-Invalid request [chars] [dec] while context is down

While the feature context was not active an invalid request was received from another layer of the CTS software stack.

asr1k-cts

LOG_STD_RECUR_ACTION

CTS_PD-3-IPC_OPEN_REPLY

3-Error

CTS-IPC Open Reply failed request [dec]

For a request from upper CTS software stack layers it was not possible to open the reply buffer.

asr1k-cts

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CTS_PD-3-IPC_NORES

3-Error

CTS-No space for the IPC reply size [dec] request [dec]

For a request from upper CTS software stack layers it was not possible to allocate space for a reply for the specified size.

asr1k-cts

LOG_STD_RECUR_ACTION

CTS_PD-3-IPC_INVALID_MSG_LEN

3-Error

CTS-Invalid IPC length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length

asr1k-cts

LOG_STD_ACTION

CTS_PD-3-IPC_SEND_FAILED

3-Error

CTS-IPC [chars] [dec] send failed [dec]

IPC message send failure

asr1k-cts

LOG_STD_ACTION

CTS_PD-3-IPC_INIT_FAILED

3-Error

CTS-IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CTS feature failed. This will cause the feature to not function.

asr1k-cts

LOG_STD_ACTION

CTS_PD-2-IPC_FAILURE

2-Critical

CTS-IPC message [chars] handler failed rc [dec]

An IPC message handler for the CTS feature failed. This will cause the feature to not function.

asr1k-cts

LOG_STD_ACTION

FME-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper FME software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-mmon

"This is normally a software issue. " LOG_STD_RECUR_ACTION

FME-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper FME software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-mmon

"This is normally a software issue. " LOG_STD_RECUR_ACTION

FME-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the FME feature failed. This will cause the feature to not function.

qfp-mmon

"This is normally a software issue. " "The consequences are that the FME feature will not function. " LOG_STD_ACTION

MMA-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper MMA software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-mma

"This is normally a software issue. " LOG_STD_RECUR_ACTION

MMA-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper MMA software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-mma

"This is normally a software issue. " LOG_STD_RECUR_ACTION

MMA-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the MMA feature failed. This will cause the feature to not function.

qfp-mma

"This is normally a software issue. " "The consequences are that the MMA feature will not function. " LOG_STD_ACTION

SWPORT_PROXY-3-SWPORT_MEM_REQ_FAILED

3-Error

SWPORT IPC subtype: [dec]

Requesting more memory failed.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-3-SWPORT_MEM_EXTEND_FAILED

3-Error

SWPORT IPC subtype: [dec]

Extending memory failed.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP SWPORT Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP SWPORT Proxy received invalid IPC message length from control plane. This message will be ignored.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP SWPORT Proxy received invalid message type [dec]

Cisco internal software error. QFP SWPORT Proxy received an invalid message from control plane. This message will be ignored.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP SWPORT Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP SWPORT Proxy initialization detected that the IPC interface initialization failed. QFP SWPORT proxy will not be functional while this condition exists.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-3-PROXY_BAD_MSG

3-Error

QFP SWPORT Proxy received bad length message type [dec]

Cisco internal software error. QFP SWPORT Proxy received a corrupted message from control plane. This message will be ignored.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP SWPORT Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP SWPORT Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-swport keyword:swport

LOG_STD_ACTION

SWPORT_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP SWPORT Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP SWPORT Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-swport keyword:swport

LOG_STD_ACTION

CAPWAP_REASS_PROXY-3-PROXY_IPC_MEM_INIT_FAILED

3-Error

-

Initialization of Capwap Reassembly memory pool failed.

cpp-ucode

LOG_STD_ACTION

CAPWAP_REASS_PROXY-3-PROXY_IPC_MEM_EXTEND_FAILED

3-Error

-

Increasing of Capwap Reassembly memory pool failed.

cpp-ucode

LOG_STD_ACTION

CAPWAP_REASS_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

CAPWAP_REASS_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

STILE_PROXY-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper STILE software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

cpp-ucode

"This is normally a software issue. " LOG_STD_ACTION

STILE_PROXY-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper STILE software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

cpp-ucode

"This is normally a software issue. " LOG_STD_ACTION

STILE_PROXY-3-IPC_UNHANDLED

3-Error

type [dec]

An unknown message was received by the STILE Client Proxy.

cpp-ucode

LOG_STD_ACTION

STILE_PROXY-3-SLINK_MEM_REQ_FAILED

3-Error

-

IPC Failure occurred when attempting to request more stile link memory.

cpp-ucode

LOG_STD_ACTION

STILE_PROXY-3-PROXY_SLINK_MEM_EXTEND_FAILED

3-Error

-

Increasing of stile slink pool failed.

cpp-ucode

LOG_STD_ACTION

STILE_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

IPC send msg for [chars] [dec] failed

IPC failed to reply

cpp-ucode

LOG_STD_ACTION

IPV6_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_INIT_FAILED

3-Error

-

Initialization of fragment information pool failed.

cpp-ucode

LOG_STD_ACTION

IPV6_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_EXTEND_FAILED

3-Error

-

Increasing of fragment information pool failed.

cpp-ucode

LOG_STD_ACTION

IPV6_REASS_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

IPV6_REASS_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

PATHMGR-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper PATHMGR software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-pathmgr

"This is normally a software issue. " LOG_STD_RECUR_ACTION

PATHMGR-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper PATHMGR software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-pathmgr

"This is normally a software issue. " LOG_STD_RECUR_ACTION

PATHMGR-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

The NAT proxy has receive an IPC with an unexpect format/data

cpp-ucode

LOG_STD_ACTION

CPP_NAT_PROXY-3-INVALID_IPC_SUBTYPE

3-Error

subtype is [dec]

The NAT proxy has receive an IPC with an unexpect subtype

cpp-ucode

LOG_STD_ACTION

CPP_NAT_PROXY-3-NAT_INIT_FAIL

3-Error

nat init failure rc= [dec]

The NAT proxy has experience a failure when trying to init NAT

cpp-ucode

LOG_STD_ACTION

CPP_NAT_PROXY-3-NAT_SEND_IPC_FAIL

3-Error

rc= [dec]

The NAT proxy has experience a failure when trying to send an IPC

cpp-ucode

LOG_STD_ACTION

ECFM_PROXY-3-ECFM_MEM_REQ_FAILED

3-Error

ECFM IPC subtype: [dec]

Requesting more memory failed.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-3-ECFM_MEM_EXTEND_FAILED

3-Error

ECFM IPC subtype: [dec]

Extending memory failed.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP ECFM Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP ECFM Proxy received invalid IPC message length from control plane. This message will be ignored.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP ECFM Proxy received invalid message type [dec]

Cisco internal software error. QFP ECFM Proxy received an invalid message from control plane. This message will be ignored.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP ECFM Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP ECFM Proxy initialization detected that the IPC interface initialization failed. QFP ECFM proxy will not be functional while this condition exists.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-3-PROXY_BAD_MSG

3-Error

QFP ECFM Proxy received bad length message type [dec]

Cisco internal software error. QFP ECFM Proxy received a corrupted message from control plane. This message will be ignored.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP ECFM Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP ECFM Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

ECFM_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP ECFM Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP ECFM Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

asr1k-ecfm keyword:ecfm

LOG_STD_ACTION

FNF_PROXY-3-IPC_UNHANDLED

3-Error

type [dec]

An unknown message was received by the Netflow Client Proxy.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-MON_CACHE_FREE_LIST_INIT

3-Error

Failed with return code: [dec]

Netflow failed to initialize the free list.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-MON_CACHE_FREE_LIST_POOL_ADD

3-Error

Failed with return code: [dec]

Netflow failed to populate the free list.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-MON_CACHE_AGER_INIT

3-Error

Failed with return code: [dec]

Netflow failed to initialize the ager.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-MON_CACHE_AGER_SHUT

3-Error

Failed with return code: [dec]

Netflow failed to shutdown the ager.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-MON_CACHE_FORCE_FLUSH

3-Error

Failed with return code: [dec]

Netflow failed to force a cache flush.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_INIT

3-Error

Failed with return code: [dec]

Netflow failed to initialize the exporter.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_SHUT

3-Error

Failed with return code: [dec]

Netflow failed to shutdown the exporter.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_OPTION_TEMPLATE_BIND

3-Error

Failed for exporter: [hec] with return code: [dec]

Netflow failed to bind an option template.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_OPTION_TEMPLATE_UNBIND

3-Error

Failed for exporter: [hec] with return code: [dec]

Netflow failed to unbind an option template.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_OPTION_TIMER_START

3-Error

Failed for exporter: [hec] with return code: [dec]

Netflow failed to start an option timer.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_OPTION_TIMER_STOP

3-Error

Failed for exporter: [hec] with return code: [dec]

Netflow failed to stop an option timer.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EXPORTER_FORCE_TEMPLATE_REFRESH

3-Error

Failed with return code: [dec]

Netflow failed to force a template refresh for an exporter.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-FLOW_CACHE_WALK

3-Error

Failed for session: [hec] with return code: [dec]

Netflow failed to process a flow cache walk request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-OBJ_MODIFY

3-Error

Failed with return code: [dec]

Netflow failed to process an object modify request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-STATS

3-Error

Failed with return code: [dec]

Netflow failed to process a stats request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-EVAL_FREC_FIELD_LIST

3-Error

Failed with return code: [dec]

Netflow failed to process an evaluate flow record field list request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-PROCESS_FREC_FIELD_LIST

3-Error

Failed with return code: [dec]

Netflow failed to process a process flow record field list request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-FLOW_CACHE_WALK_FLEXIBLE

3-Error

Failed for session: [hec] with return code: [dec]

Netflow failed to process a flow cache walk/flexible request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-PROXY_IPC_PAK_ALLOC_FAILED

3-Error

-

Allocation of IPC packet failed.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

[dec]

Could not send IPC reply for proxy request.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-MON_CACHE_CLEAN

3-Error

Failed with return code: [dec]

Netflow failed to perform cache cleanup.

cpp-ucode

LOG_STD_ACTION

FNF_PROXY-3-FNF_CWALK_TOP_TALKERS_INVALID_SORT

3-Error

This field can't be used for sort

Show Top Talkers command contains sort field specification that is not supported.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST_PROXY-3-PROXY_MEM_EXTEND_FAILED

3-Error

IPC subtype: [dec]

add more memory failed.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST_PROXY-3-PROXY_IPC_FAILED

3-Error

[chars] failed to send ipc rc: [dec]

send ipc failed.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length.

cpp-ucode

LOG_STD_ACTION

DIALER_LIST_PROXY-3-PROXY_ALLOC_PAK_FAILED

3-Error

alloc pak failed

alloc pak failed.

cpp-ucode

LOG_STD_ACTION

LISP_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

lisp proxy init failed rc = [dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

LISP_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

invalid lisp proxy msg [dec]

Received an invalid IPC messages subtype.

cpp-ucode

LOG_STD_ACTION

LISP_PROXY-3-PROXY_IPC_PACKET_ALLOCATION_FAILED

3-Error

lisp proxy alloc reply pak failed

Failed to allocate packet buffer for IPC

cpp-ucode

LOG_STD_ACTION

LISP_PROXY-3-PROXY_IPC_PACKET_SEND_FAILED

3-Error

lisp proxy send failed rc = [dec]

Failed to send IPC packet.

cpp-ucode

LOG_STD_ACTION

LISP_PROXY-3-PROXY_IPC_REQUEST_MSG_INVALID

3-Error

lisp proxy request msg invalid.

Failed to get lisp default entry stats req from IPC packet.

cpp-ucode

LOG_STD_ACTION

LISP_PROXY-3-PROXY_IPC_GET_STATS_FAILED

3-Error

lisp proxy get stats failed for type[[chars]] idx = [dec] ppe_addr[0x[hec]].

Getting lisp default entry stats failed.

cpp-ucode

LOG_STD_ACTION

MEM_PROXY-3-PROXY_IPC_PAK_ALLOC_FAILED

3-Error

-

Allocation of IPC packet failed.

cpp-ucode

LOG_STD_ACTION

MEM_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

[chars]

Could not send IPC request for more memory.

cpp-ucode

LOG_STD_ACTION

GEN_PROXY-3-IPC_UNHANDLED

3-Error

failure

An unknown message type: [dec] was received by the Generic Client Proxy.

cpp-ucode

LOG_STD_ACTION

GEN_PROXY-3-REPLY_MSG

3-Error

wrong version [dec]

An incorrect SBS message was received by the Generic Client Proxy.

cpp-ucode

LOG_STD_ACTION

GEN_PROXY-3-STACK_ALLOC_FAILED

3-Error

Stack allocation for reply failed reply_size [hec]

Stack space could not be allocated for reply.

cpp-ucode

LOG_STD_ACTION

GEN_PROXY-3-GPM_ALLOC_FAILED

3-Error

GPM allocation for reply failed pak_size [hec] reply_size [hec]

GPM could not be allocated for reply.

cpp-ucode

LOG_STD_ACTION

GEN_PROXY-3-IPC_SEND_FAILED

3-Error

IPC send reply failed [chars]

GEN proxy failed to send of reply to IPC msg.

cpp-ucode

LOG_STD_ACTION

EVTMON_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

qfp-evtmon

LOG_STD_ACTION

EVTMON_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[hec]

Received an invalid IPC messages subtype.

qfp-evtmon

LOG_STD_ACTION

EVTMON_PROXY-4-PROXY_IPC_EVTMON_FEAT_UPDATE_FAILED

4-Warning

feature user failed to [chars] because of [chars]

Event monitor feature user failed to attach or detach.

qfp-evtmon

LOG_STD_ACTION

EVTMON_PROXY-4-PROXY_IPC_EVTMON_REC_UPDATE_FAILED

4-Warning

event record update failed

Event monitor failed to attach or detach event record.

qfp-evtmon

LOG_STD_ACTION

IPC_TEST-3-INVALID_SUBTYPE

3-Error

CPP IPC TEST Proxy subtype [dec]

IPC test proxy failed because of receiving invalid sub-type.

cpp-ucode

LOG_STD_ACTION

IPC_TEST-3-REPLY_FAILED

3-Error

CPP IPC TEST Proxy send reply

IPC test proxy failed because the reply failed to send.

cpp-ucode

-

IPC_TEST-3-MEM_ALLOC_FAILED

3-Error

CPP IPC TEST Proxy mem alloc

IPC test proxy failed because the GPM allocation failed.

cpp-ucode

-

HA_PROXY-3-PROXY_IPC_PAK_ALLOC_FAILED

3-Error

-

Allocation of IPC packet failed.

cpp-ucode

LOG_STD_ACTION

HA_PROXY-2-HA_SESSION_ALLOC_FAILED

2-Critical

[chars]: unable to allocate entry for [chars] binding

HA could not allocate a control block to manage the service

cpp-ucode

LOG_STD_ACTION

HA_PROXY-2-HA_FIND_SERVICE_FAILED

2-Critical

[chars]: unable to find [chars] service

HA could not find the specified service

cpp-ucode

LOG_STD_ACTION

HA_PROXY-3-HA_DUP_SERVICE_NAME

3-Error

[chars]: Duplicate service name: [chars] on bind

Duplicate service name on ha service bind

cpp-ucode

LOG_STD_ACTION

HA_PROXY-3-HA_DUP_SERVICE_INDEX

3-Error

[chars]: Duplicate service index: [dec] on bind

Duplicate service index on ha service bind

cpp-ucode

LOG_STD_ACTION

HA_PROXY-3-HA_INVALID_REQUEST

3-Error

[chars]: Unknown request: [dec]

HA control services received unknown request

cpp-ucode

LOG_STD_ACTION

HA_PROXY-3-HA_MALFORMED_PKT

3-Error

Malformed packet bad [chars] [hec]

HA Sync packet was malformed may not have been fully processed

cpp-ucode

LOG_STD_ACTION

HA_PROXY-4-HA_UNKNOWN_SERVICE

4-Warning

Sync msg for unknown service [hec] rg [hec]

HA Sync received a message for an unknown service

cpp-ucode

LOG_STD_ACTION

HA_PROXY-4-HA_PKT_ERROR

4-Warning

Error processing HA sync pkt rg [hec]

HA Sync packet was dropped while processing

cpp-ucode

LOG_STD_ACTION

CVLA-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper CVLA software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as infra activation.

qfp-cvla

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CVLA-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper CVLA software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as infra activation.

qfp-cvla

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CVLA-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CVLA infra failed. This will cause the infra to not function.

qfp-cvla

"This is normally a software issue. " "The consequences are that the CVLA infra will not function. " LOG_STD_ACTION

CPP_LDN-2-PROXY_IPC_INIT_FAILED

2-Critical

CPP LDN Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. CPP LDN initialization detected that the Proxy IPC interface initialization failed. The LDN Proxy will not be functional while this condition exists.

cpp-ucode

LOG_STD_ACTION

CPP_LDN-3-PROXY_IPC_SEND

3-Error

failure: [chars]

LDN Proxy send response failed response was dropped.

cpp-ucode

LOG_STD_ACTION

CPP_LDN-3-PROXY_IPC_INVALID

3-Error

failure: [dec]

LDN Proxy received an invalid IPC msg from the client.

cpp-ucode

LOG_STD_ACTION

CPP_LDN-3-PROXY_GPM_RSRC_FAIL

3-Error

failure: [chars]

LDN Proxy failed in performing a GPM operation.

cpp-ucode

LOG_STD_ACTION

CPP_LDN-3-PROXY_METAPKT_ENQ

3-Error

subdevice id: [dec] failure: [dec]

LDN Proxy metapacket enqueue failed.

cpp-ucode

LOG_STD_ACTION

CFT-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper CFT software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-cft

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CFT-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper CFT software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-cft

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CFT-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CFT feature failed. This will cause the feature to not function.

qfp-cft

"This is normally a software issue. " "The consequences are that the CFT feature will not function. " LOG_STD_ACTION

CPP_FLOWDB_PROXY-3-INVALID_IPC_SUBTYPE

3-Error

subtype is [dec]

The flow database proxy has receive an IPC with an unexpected subtype

csr1kv-dp-infra

LOG_STD_ACTION

CPP_FLOWDB_PROXY-3-FLOWDB_INIT_FAIL

3-Error

flowdb proxy init failure rc= [dec]

The flow database proxy has experienced a failure when trying to init

csr1kv-dp-infra

LOG_STD_ACTION

CPP_FLOWDB_PROXY-3-FLOWDB_SEND_IPC_FAIL

3-Error

rc= [dec]

The flow database proxy has experience a failure when trying to send an IPC

csr1kv-dp-infra

LOG_STD_ACTION

CPP_FLOWDB_PROXY-3-FLOWDB_UNEXPECTED_ERR

3-Error

rc= [dec]

The flow database proxy has experienced an unexpected condition

csr1kv-dp-infra

LOG_STD_ACTION

CPP_BQS_QMOVE-3-PROXY_TIMEOUT

3-Error

Proxy Operation: [chars] node_id [hec] data [hec] data [hec]

BQS Proxy operation timeout. Proxy will continue to retry operatin.

qfp-bqs-internal

LOG_STD_ACTION

CPP_BQS_QMOVE-3-PROXY_ERROR

3-Error

Proxy Operation Failed: [chars]

BQS Proxy operation failed.

qfp-bqs-internal

LOG_STD_ACTION

CPP_BQS_QMOVE-3-PROXY_COMPLETE

3-Error

Proxy Operation: [chars]

Operation that was flagged as timed out has now completed

qfp-bqs-internal

LOG_STD_ACTION

CPP_BQS-3-INVALID_SUBTYPE

3-Error

CPP BQS RM Proxy subtype [dec]

BQS proxy failed because of receiving invalid sub-type or failed to allocate ipc response buffer.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-3-INIT_FAILED

3-Error

CPP BQS RM Proxy region [chars]

BQS proxy failed due initialize or resize software managed memory.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-3-CMD_ACTIVE

3-Error

CPP BQS Proxy Command correlator [dec]

A BQS Proxy command was received but the correlator was still in use. Commad was not processed.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-2-MPASS_FS_REG

2-Critical

CPP BQS PROXY feature special vector [dec] registration failed result: [dec]

Cisco internal software error. CPP multipass registration of a feature special processing vector for BQS Proxy failed. The BQS proxy will not be fully functional while this condition exists.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-3-CARVE

3-Error

[chars]: size [dec] SW carved out memory region initialization failed.

A BQS proxy failed to initialize the software memory region.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-3-RESIZE

3-Error

CPP BQS Proxy Memory Manager region [chars]

BQS proxy failed to resize software managed memory.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-2-PROXY_IPC_INIT_FAILED

2-Critical

CPP BQS Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. CPP BQS initialization detected that the Proxy IPC interface initialization failed. The BQS Proxy will not be functional while this condition exists.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-3-PROXY_IPC_SEND

3-Error

failure: [chars]

BQS Proxy send response failed response was dropped.

cpp-ucode

LOG_STD_ACTION

CPP_BQS-3-MAX_GPM_TX_LEN_EXCEED

3-Error

CPP BQS Proxy Command exceed GPM tx len [dec]

A BQS Proxy command recycle a packet exceed GPM tx len

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_EXTENDED_PKT_MEM_INIT_FAILED

3-Error

[dec]

Initialization of extended packet memory failed.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_SEG_DLIST_MEM_INIT_FAILED

3-Error

[dec]

Initialization of segmented packet dlist memory failed.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_PBUF_MEM_INIT_FAILED

3-Error

[dec]

Initialization of packet buffer header memory failed.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_SEG_DLIST_EXTEND_FAILED

3-Error

[dec]

Extending of segmented packet dlist memory failed.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_PBUF_EXTEND_FAILED

3-Error

[dec]

Extending of packet buffer header memory failed.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_PKT_DRAM_EXTEND_FAILED

3-Error

[dec]

Extending of extended packet memory failed.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-4-PROXY_IPC_UNKNOWN_SUBTYPE

4-Warning

[dec]

Unknown IPC message detected.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

[dec]

Could not initialize IPC handler.

cpp-ucode

LOG_STD_ACTION

PA_PKT_PROXY-3-PROXY_IPC_INVALID_MSG

3-Error

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid length for IPC message.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_MEM_EXTEND_FAILED

3-Error

-

Extending memory failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IPC_INVALID_PARAM

3-Error

-

IPC Invalid parameters.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

-

Invalid IPC message

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_DEBUG_REG_FAILED

3-Error

-

DSA Conditional Debugging registration failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IPC_SEND_CLEAR_FAILED

3-Error

[dec]

DSA clear ip cache failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IPC_SEND_UNINIT_FAILED

3-Error

[dec]

DSA Send UNINIT IPC failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IPC_SEND_INIT_FAILED

3-Error

[dec]

Send initialization IPC failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_UNINIT_FAILED

3-Error

-

UNINIT cleanup failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

-

Generating IPC failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_CHUNK_CLEAR_FAILED

3-Error

-

Chunk clear failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_CHUNK_CREATION_FAILED

3-Error

-

Chunk creation failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_LOW_MEM_REQ_FAILED

3-Error

-

Send low mem IPC failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_RETURN_MEM_FAILED

3-Error

-

return mem IPC failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_NO_IP_POOL_MEM

3-Error

-

IP Cache pool is not allocated.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_TBL_INIT_FAILED

3-Error

-

IP Cache table init failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IP_CLEAR_FAILED

3-Error

[dec]

IP Cache clear failed.

cpp-ucode

LOG_STD_ACTION

DSA_PROXY-3-PROXY_IP_CLEAR_TO_FAILED

3-Error

[dec] [dec]

IP Cache clear failed.

cpp-ucode

LOG_STD_ACTION

FMD-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper FMD software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-fmd

"This is normally a software issue. " LOG_STD_RECUR_ACTION

FMD-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper FMD software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-fmd

"This is normally a software issue. " LOG_STD_RECUR_ACTION

FMD-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the FMD feature failed. This will cause the feature to not function.

qfp-fmd

"This is normally a software issue. " "The consequences are that the FMD feature will not function. " LOG_STD_ACTION

ESS_PROXY-2-IPC_THROTTLE_ERR

2-Critical

Allocation of [chars] memory failed for ESS Proxy unsolicited event throttling

Allocation of memory resource demanded by ESS Proxy throttle failed. This is a serious problem at the ESS Proxy IPC initialization for unsolicited event throttling.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

CPP ESS Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. CPP ESS Proxy initialization detected that the IPC interface initialization failed. CPP ESS proxy will not be functional while this condition exists.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-3-PROXY_BAD_MSG

3-Error

CPP ESS Proxy received bad length message type [dec]

Cisco internal software error. CPP ESS Proxy received a corrupted message from control plane. This message will be ignored.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-3-PROXY_INV_MSG

3-Error

CPP ESS Proxy received invalid message type [dec]

Cisco internal software error. CPP ESS Proxy received an invalid message type from control plane. This message will be ignored.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

CPP ESS Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. CPP ESS Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

CPP ESS Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. CPP ESS Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-3-PROXY_IPC_NO_HDLR

3-Error

CPP ESS Proxy received unregistered message type [dec]

Cisco internal software error. CPP ESS Proxy received a message from control plane but there is no registered handler. The message is lost as the result of this condition.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-2-KA_CHANNEL_ALLOC_FAILED

2-Critical

CPP ESS Proxy Session Keepalive channel creation failure.

Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the channel creation failed. CPP ESS proxy session keepalive will not be functional while this condition exists.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-2-KA_PKT_REPLICA_REG_FAILED

2-Critical

CPP ESS Proxy Session Keepalive packet replication registration failure result: [dec].

Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the packet replication registration failed. CPP ESS proxy session keepalive will not be functional while this condition exists.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-2-KA_TIMER_INIT_FAILED

2-Critical

CPP ESS Proxy Session Keepalive timer initialization failure.

Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the timer initialization failed. CPP ESS proxy session keepalive will not be functional while this condition exists.

qfp-bb keyword:none

LOG_STD_ACTION

ESS_PROXY-2-KA_PKT_TMPL_BFR_ALLOC_FAILED

2-Critical

CPP ESS Proxy Session Keepalive packet template allocation failure [chars] buffer length: [dec].

Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the packet template buffer allocation failed. CPP ESS proxy session keepalive will not be functional while this condition exists.

qfp-bb keyword:none

LOG_STD_ACTION

OPENDNS_PROXY-2-OPENDNS_MSG_PROXYINIT_FAILURE

2-Critical

UMBRELLA - Failed to register IPC message handler result code [dec]

QFP Umbrella feature failed to register an IPC message handler for communication with control plane. This will cause the featue not to function.

OPENDNS_COMP_NAME

LOG_STD_ACTION

OPENDNS_PROXY-3-OPENDNS_MSG_PROXY_UNKNOWN_IPCMSG

3-Error

UMBRELLA - Received an unknown type code [dec] IPC message

QFP Umbrella feature received an unknown message from another layer of Umbrella feature's software stack.

OPENDNS_COMP_NAME

LOG_STD_RECUR_ACTION

OPENDNS_PROXY-3-OPENDNS_MSG_PROXY_INVALID_MSGLEN

3-Error

UMBRELLA - Received an invalid length IPC message

QFP Umbrella feature received an incorrect length of IPC message from anoter layer of Umbrella feature's software stack m_enum [dec] m_subtype [dec] m_len [dec] m_flags 0x[hec] m_source [dec].

OPENDNS_COMP_NAME

LOG_STD_ACTION

OPENDNS_PROXY-3-OPENDNS_MSG_PROXY_ALLOC_FAILURE

3-Error

UMBRELLA - Failed to get [dec] bytes space for IPC reply message

QFP Umbrella feature detected buffer allocation failure while sending reply to a message from another layer of Umbrella feature's software stack.

OPENDNS_COMP_NAME

LOG_STD_ACTION

OPENDNS_PROXY-3-OPENDNS_MSG_PROXY_OPENREPLY_FAIL

3-Error

UMBRELLA - Failed to open reply message part of IPC packet

QFP Umbrella feature failed to open message part of IPC packet while sending a reply to another layer of Umbrella feature's software stack.

OPENDNS_COMP_NAME

LOG_STD_ACTION

OPENDNS_PROXY-3-OPENDNS_MSG_PROXY_IPCSEND_FAIL

3-Error

UMBRELLA - Failed to send IPC message result code [dec]

QFP Umbrella feature failed to send IPC message to another layer of Umbrella feature's software stack.

OPENDNS_COMP_NAME

LOG_STD_ACTION

OPENDNS_PROXY-3-OPENDNS_MSG_PROXY_DEBUG_REG_FAILED

3-Error

-

Umbrella Conditional Debugging Registration failed.

OPENDNS_COMP_NAME

LOG_STD_ACTION

IP_TUNNEL-3-VRF_HOST_MEM_REQ_FAILED

3-Error

QFP TUNNEL Proxy IPC VRF host mem req failed

Requesting more memory failed.

qfp-tunnel keyword:tunnel

LOG_STD_ACTION

IP_TUNNEL-3-VRF_HOST_MEM_EXTEND_FAILED

3-Error

QFP TUNNEL Proxy IPC VRF host mem extend failed

Extending memory failed.

qfp-tunnel keyword:tunnel

LOG_STD_ACTION

IP_TUNNEL-4-INVALID_MSG_LEN

4-Warning

QFP TUNNEL Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP TUNNEL Proxy received invalid IPC message length from control plane. This message will be ignored.

qfp-tunnel keyword:tunnel

LOG_STD_ACTION

IP_TUNNEL-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper TUNNEL software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-ip-tunnel

"This is normally a software issue. " LOG_STD_RECUR_ACTION

IP_TUNNEL-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper TUNNEL software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-ip-tunnel

"This is normally a software issue. " LOG_STD_RECUR_ACTION

IP_TUNNEL-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the Tunnel feature failed. This may cause the feature to not function.

qfp-ip-tunnel

"This is normally a software issue. " "The consequences are that the tunnel feature may not function. " LOG_STD_ACTION

CENT-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper CENT software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-cent

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CENT-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper CENT software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation.

qfp-cent

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CENT-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CENT feature failed. This will cause the feature to not function.

qfp-cent

"This is normally a software issue. " "The consequences are that the CENT feature will not function. " LOG_STD_ACTION

CPP_IPHC_PROXY-3-INVALID_IPC_INPUT

3-Error

[chars] CPP IPHC Client Proxy failure

IPHC proxy failed because of receiving invalid sub-type or failed to allocate ipc response buffer.

cpp-ucode

LOG_STD_ACTION

CPP_NAT64_PROXY-3-NAT64_IPC_FAIL

3-Error

rc= [dec]

The NAT64 proxy has received an IPC with an unexpected format/data

cpp-ucode

LOG_STD_ACTION

CPP_NAT64_PROXY-3-INVALID_IPC_SUBTYPE

3-Error

subtype is [dec]

The NAT64 proxy has received an IPC with an unexpected subtype

cpp-ucode

LOG_STD_ACTION

CPP_NAT64_PROXY-3-NAT64_INIT_FAIL

3-Error

nat64 init failure rc= [dec]

The NAT proxy has experienced a failure when trying to initialize the NAT64 proxy

cpp-ucode

LOG_STD_ACTION

CPP_NAT64_PROXY-3-NAT_INIT_FAIL

3-Error

nat64 init failure rc= [dec]

The NAT64 proxy has experience a failure when trying to init NAT64

cpp-ucode

LOG_STD_ACTION

TCP_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP TCP Proxy IPC initialization failure result: [dec].

Cisco internal software error. QFP TCP Proxy initialization detected that the IPC interface initialization failed. QFP TCP proxy will not be functional while this condition exists.

qfp-tcp keyword:none

LOG_STD_ACTION

TCP_PROXY-3-PROXY_BAD_MSG

3-Error

CPP TCP Proxy received bad length message type [dec]

Cisco internal software error. CPP TCP Proxy received a corrupted message from control plane. This message will be ignored.

qfp-tcp keyword:none

LOG_STD_ACTION

TCP_PROXY-3-PROXY_INV_MSG

3-Error

CPP TCP Proxy received invalid message type [dec]

Cisco internal software error. CPP TCP Proxy received an invalid message type from control plane. This message will be ignored.

qfp-tcp keyword:none

LOG_STD_ACTION

TCP_PROXY-3-PROXY_IPC_CHUNK_FAILED

3-Error

CPP TCP Proxy chunk memory failure [dec]

Cisco internal software error. QFP TCP Proxy chunk memory allocation detected failure. QFP TCP proxy will not be functional while this condition exists.

qfp-tcp keyword:none

LOG_STD_ACTION

TCP_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

CPP TCP Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. CPP TCP Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-tcp keyword:none

LOG_STD_ACTION

TCP_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

CPP TCP Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. CPP TCP Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-tcp keyword:none

LOG_STD_ACTION

TCP_PROXY-3-PROXY_DEBUG_REG_FAILED

3-Error

-

TCP Conditional Debugging registration failed.

qfp-tcp keyword:none

LOG_STD_ACTION

CXSC-3-IPC_INVALID_MSG

3-Error

CXSC-Invalid request [dec]

We received an invalid message from another layer of the CXSC software stack.

qfp-cxsc

LOG_STD_RECUR_ACTION

CXSC-3-FEAT_DOWN

3-Error

CXSC-Invalid request [chars] [dec] while feature is down

While the feature was not active an invalid request was received from another layer of the CXSC software stack.

qfp-cxsc

LOG_STD_RECUR_ACTION

CXSC-3-FEAT_CTX_DOWN

3-Error

CXSC-Invalid request [chars] [dec] while context is down

While the feature context was not active an invalid request was received from another layer of the CXSC software stack.

qfp-cxsc

LOG_STD_RECUR_ACTION

CXSC-3-IPC_OPEN_REPLY

3-Error

CXSC-IPC Open Reply failed request [dec]

For a request from upper CXSC software stack layers it was not possible to open the reply buffer.

qfp-cxsc

"This is normally a software issue. " LOG_STD_RECUR_ACTION

CXSC-3-IPC_NORES

3-Error

CXSC-No space for the IPC reply size [dec] request [dec]

For a request from upper CXSC software stack layers it was not possible to allocate space for a reply for the specified size.

qfp-cxsc

LOG_STD_RECUR_ACTION

CXSC-3-IPC_INVALID_MSG_LEN

3-Error

CXSC-Invalid IPC length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length

qfp-cxsc

LOG_STD_ACTION

CXSC-3-IPC_SEND_FAILED

3-Error

CXSC-IPC [chars] [dec] send failed [dec]

IPC message send failure

qfp-cxsc

LOG_STD_ACTION

CXSC-2-IPC_INIT_FAILED

2-Critical

CXSC-IPC message handler registration failure rc [dec]

Registering an IPC message handler for the CXSC feature failed. This will cause the feature to not function.

qfp-cxsc

LOG_STD_ACTION

CXSC-2-IPC_FAILURE

2-Critical

CXSC-IPC message [chars] handler failed rc [dec]

An IPC message handler for the CXSC feature failed. This will cause the feature to not function.

qfp-cxsc

LOG_STD_ACTION

PDU_SESS_PROXY-3-PDU_SESS_MEM_REQ_FAILED

3-Error

PDU_SESS IPC subtype: [dec]

Requesting more memory failed.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-3-PDU_SESS_MEM_EXTEND_FAILED

3-Error

PDU_SESS IPC subtype: [dec]

Extending memory failed.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-4-PROXY_INVALID_MSG_LEN

4-Warning

QFP PDU_SESS Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec]

Cisco internal software error. QFP PDU_SESS Proxy received invalid IPC message length from control plane. This message will be ignored.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-4-PROXY_INVALID_MSG

4-Warning

QFP PDU_SESS Proxy received invalid message type [dec]

Cisco internal software error. QFP PDU_SESS Proxy received an invalid message from control plane. This message will be ignored.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-3-PROXY_NULL_MSG

3-Error

QFP PDU_SESS Proxy received null message

Cisco internal software error. QFP PDU_SESS Proxy received an null message from control plane. This message will be ignored.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP PDU_SESS Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP PDU_SESS Proxy initialization detected that the IPC interface initialization failed. QFP PDU_SESS proxy will not be functional while this condition exists.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-3-PROXY_BAD_MSG

3-Error

QFP PDU_SESS Proxy received bad length message type [dec]

Cisco internal software error. QFP PDU_SESS Proxy received a corrupted message from control plane. This message will be ignored.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP PDU_SESS Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP PDU_SESS Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

PDU_SESS_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP PDU_SESS Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP PDU_SESS Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-pdu_sess keyword:pdu_sess

LOG_STD_ACTION

SBC-3-FEAT_DOWN

3-Error

Invalid request [chars] while feature down call id [dec]

While the feature was not active an invalid request was received from another layer of the SBC software stack for the specified call ID. Some requests do not have an associated call ID. For them the displayed call ID is zero.

cpp-sbc

"This is a software issue. The consequences " "could be limited to only one or a few calls. " LOG_STD_RECUR_ACTION

SBC-3-FEAT_UP

3-Error

Invalid request [chars] while feature up

While the feature was active an invalid request was received from another layer of the SBC software stack.

cpp-sbc

"This is a software issue. " "There are no consequences as this can only have been an Init request " "while the feature was already active. " LOG_STD_RECUR_ACTION

SBC-3-NO_RES

3-Error

[chars] resource not available for the [chars] request call id [dec]

The specified software resource was not available or could not be located for the specified request from upper SBC software stack layers for the specified call ID.

cpp-sbc

"This is a software issue. The consequences " "are that the specified request could not be performed. " LOG_STD_RECUR_ACTION

SBC-3-IPC_OPEN_REPLY

3-Error

IPC Open Reply failed request [dec]

For a request from upper SBC software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck call that cannot be established etc. In rare cases this could also affect other operations such as feature activation deactivation modification High-Availability switchover operations.

cpp-sbc

"This is normally a software issue. " LOG_STD_RECUR_ACTION

SBC-3-IPC_NORES

3-Error

No space for the IPC reply size [dec]

For a request from upper SBC software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck call that cannot be established etc. In rare cases this could also affect other operations such as feature activation deactivation modification High-Availability switchover operations.

cpp-sbc

"This is normally a software issue. " LOG_STD_RECUR_ACTION

SBC-2-IPC_INIT

2-Critical

IPC message handler registration failure rc [dec]

Registering an IPC message handler for the SBC feature failed. This will cause the feature not to function. The function

cpp-sbc

"This is normally a software issue. " "The consequences are that the SBC feature will not function. " LOG_STD_ACTION

SBC-3-MEM_INIT_FAILED

3-Error

Allocation of [chars] memory failed for SBC

SBC Initialization of channel pool failed.

cpp-sbc

LOG_STD_ACTION

SBC-3-PKT_REPLICA_INIT_FAILED

3-Error

Register to Generic Packet Replication failed for SBC

SBC Initialization of packet replication registration failed.

cpp-sbc

LOG_STD_ACTION

SBC-3-SSL_APPL_REG_FAILED

3-Error

QFP SBC Websocket register to SSL library failed

Cisco internal software error. QFP SBC WS feature initialization detected that the SSL library registration failed. QFP SBC WS will not be functional while this condition exists.

cpp-sbc

LOG_STD_ACTION

IPC-3-LOG_ERR

3-Error

[chars] CPP QoS Client Proxy failure

QoS proxy failed because of receiving invalid sub-type or failed to allocate ipc response buffer.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-2-TVI_MSG_PROXYINIT_FAILURE

2-Critical

ET-Analytics - Failed to register IPC message handler result code [dec]

QFP ET-Analytics feature failed to register an IPC message handler for communication with control plane. This will cause the featue not to function.

TVI_COMP_NAME

LOG_STD_ACTION

TVI_PROXY-3-TVI_MSG_PROXY_UNKNOWN_IPCMSG

3-Error

ET-Analytics - Received an unknown type code [dec] IPC message

QFP ET-Analytics feature received an unknown message from another layer of ET-Analytics feature's software stack.

TVI_COMP_NAME

LOG_STD_RECUR_ACTION

TVI_PROXY-3-TVI_MSG_PROXY_INVALID_MSGLEN

3-Error

ET-Analytics - Received an invalid length IPC message

QFP ET-Analytics feature received an incorrect length of IPC message from anoter layer of ET-Analytics feature's software stack m_enum [dec] m_subtype [dec] m_len [dec] m_flags 0x[hec] m_source [dec].

TVI_COMP_NAME

LOG_STD_ACTION

TVI_PROXY-3-TVI_MSG_PROXY_ALLOC_FAILURE

3-Error

ET-Analytics - Failed to get [dec] bytes space for IPC reply message

QFP ET-Anallytics feature detected buffer allocation failure while sending reply to a message from another layer of ET-Analytics feature's software stack.

TVI_COMP_NAME

LOG_STD_ACTION

TVI_PROXY-3-TVI_MSG_PROXY_OPENREPLY_FAIL

3-Error

ET-Analytics - Failed to open reply message part of IPC packet

QFP ET-Analytics feature failed to open message part of IPC packet while sending a reply to another layer of ET-Analytics feature's software stack.

TVI_COMP_NAME

LOG_STD_ACTION

TVI_PROXY-3-TVI_MSG_PROXY_IPCSEND_FAIL

3-Error

ET-Analytics - Failed to send IPC message result code [dec]

QFP ET-Analytics feature failed to send IPC message to another layer of ET-Analytics feature's software stack.

TVI_COMP_NAME

LOG_STD_ACTION

TVI_PROXY-3-TVI_MSG_PROXY_DEBUG_REG_FAILED

3-Error

-

ET-Analytics Conditional Debugging Registration failed.

TVI_COMP_NAME

LOG_STD_ACTION

TVI_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid ET-Analytics IPC message length.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_CREATE_FAILED

3-Error

-

HSL creation failed.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_ADD_DEST_FAILED

3-Error

-

HSL add destination failed.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-4-PROXY_HSL_ALREADY_INIT

4-Warning

-

HSL logger already initialized

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_MODIFY_DEST_FAILED

3-Error

-

HSL modify destination failed.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_BIND_FAILED

3-Error

-

HSL bind failed.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_ENABLE_FAILED

3-Error

-

HSL enable failed.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-4-PROXY_HSL_NOT_INIT

4-Warning

[dec]

HSL logger not initialized

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_MODIFY_FAILED

3-Error

-

HSL modification failed.

cpp-ucode

LOG_STD_ACTION

TVI_PROXY-3-PROXY_HSL_BIND_TEMPLATE_FAILED

3-Error

[dec]

HSL bind tempalte failed at given index.

cpp-ucode

LOG_STD_ACTION

SSLVPN_PROXY-2-PROXY_IPC_INIT_FAILED

2-Critical

QFP SSLVPN Proxy IPC interface initialization failure result: [dec].

Cisco internal software error. QFP SSLVPN Proxy initialization detected that the IPC interface initialization failed. QFP SSLVPN proxy will not be functional while this condition exists.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-3-PROXY_BAD_MSG

3-Error

QFP SSLVPN Proxy received bad length message type [dec]

Cisco internal software error. QFP SSLVPN Proxy received a corrupted message from control plane. This message will be ignored.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-3-PROXY_INV_MSG

3-Error

QFP SSLVPN Proxy received invalid message type [dec]

Cisco internal software error. QFP SSLVPN Proxy received an invalid message from control plane. This message will be ignored.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-3-PROXY_IPC_ALLOC_FAILED

3-Error

QFP SSLVPN Proxy [chars] message lost due to message buffer allocation failure.

Cisco internal software error. QFP SSLVPN Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-3-PROXY_IPC_SEND_FAILED

3-Error

QFP SSLVPN Proxy [chars] message lost due to message sent failure result: [dec].

Cisco internal software error. QFP SSLVPN Proxy message processing detected a message sent failure. The message is lost as the result of this condition.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-4-PROXY_CRYPTO_CTX_REQ_FAIL

4-Warning

QFP SSLVPN Proxy failed to replenish hardware context handles.

Cisco internal software error. QFP SSLVPN Proxy message processing detected out-of-resource condition and cannot replenish hardware context handles. QFP SSLVPN will not be functional properly while this conidtion exist.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-3-PROXY_SSL_CTX_MEM_REQ_FAIL

3-Error

QFP SSLVPN Proxy failed to repleneish SSL context memory.

Cisco internal software error. QFP SSLVPN Proxy message processing detected leaking of SSL context memory condition. QFP SSLVPN will not be functional properly while this condition exist.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

SSLVPN_PROXY-3-PROXY_CRYPTO_CTX_MEM_REQ_FAIL

3-Error

QFP SSLVPN Proxy failed to repleneish crypto context memory.

Cisco internal software error. QFP SSLVPN Proxy message processing detected leaking of crypto context memory condition. QFP SSLVPN will not be functional properly while this condition exist.

qfp-ssl keyword:sslvpn

LOG_STD_ACTION

THREAT_DEFENSE_PROXY-3-PROXY_MEM_EXTEND_FAILED

3-Error

-

Extending memory failed.

cpp-ucode

LOG_STD_ACTION

THREAT_DEFENSE_PROXY-4-PROXY_IPC_INVALID_MSG_LEN

4-Warning

[dec]:[dec] len [dec] flags 0x[hec] source [dec]

Invalid IPC message length.

cpp-ucode

LOG_STD_ACTION

THREAT_DEFENSE_PROXY-4-PROXY_IPC_INVALID_MSG

4-Warning

[dec]

Invalid IPC message

cpp-ucode

LOG_STD_ACTION

THREAT_DEFENSE_PROXY-3-PROXY_IPC_INIT_FAILED

3-Error

[dec]

IPC handler initialization failed.

cpp-ucode

LOG_STD_ACTION

CPPDRV-6-INTR

6-Information

[chars][dec] Interrupt : [chars]

A CPP hardware interrupt has occurred.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-2-HALT

2-Critical

[chars][dec] Interrupt : [chars] Seq:%03d Halt bit set.

A Serious CPP hardware error has occurred.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-HOT

3-Error

[chars][dec] Interrupt : [chars] Seq:%03d repeating interrupt has been disabled.

A repeating hardware interrupt has been disabled.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-TCAM_PERR

3-Error

[chars][dec] TCAM Parity error TCAM device #[dec] at offset 0x%08X.

A Parity error has occurred in a TCAM device.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-TCAM_PERR_FAILURE

3-Error

[chars][dec] Failed to correct TCAM Parity error. Parity error detection disabled.

Failed to correct a TCAM Parity error and further detection has been disabled.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-SRT_PERR_FAILURE

3-Error

[chars][dec] Failed to correct BQS SRT Parity error.

Failed to correct a BQS SRT Parity error.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-LOCKDOWN

3-Error

QFP[dec].[dec] CPP Driver LOCKDOWN encountered due to previous fatal error [chars]: [chars].

A fatal error has caused the driver to LOCKDOWN.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-LOCKDOWN_INITIATED

3-Error

QFP[dec].[dec] CPP Driver LOCKDOWN being triggered due to fatal error.

A fatal error has caused the process to initiate LOCKDOWN.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-INIT_NOTF_ID

3-Error

CPP[dec]: Failed to initialize: [chars]

A function failed to initialize.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-INIT_NOTF

3-Error

Failed to initialize: [chars]

A function failed to initialize.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-DESTROY_NOTF

3-Error

Failed to destroy connection :[chars]

A function failed to destroy a connection.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-CLEANUP_NOTF

3-Error

Failed to Cleanup: [chars]

A function failed to cleanup data.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-ALLOC_NOTF

3-Error

CPP[dec]: Failed to Allocate: [chars]

A function failed to allocate data.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_PLAT_DB

3-Error

CPP[dec]: 0x[hec] Platform failure accessing [chars]

Platform DB query failed

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INTERRUPT_CLEAR

3-Error

CPP[dec]: 0x[hec] Failed to clear [chars] interrupt

Failed to clear an interrupt node

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INTERRUPT_OPEN

3-Error

CPP[dec]: 0x[hec] Failed to access [chars] interrupt node - [chars]

Failed to open an interrupt

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INTERRUPT_HANDLER

3-Error

CPP[dec]: 0x[hec] Failed to register [chars] interrupt handler - [chars]

Failed to register interrupt handler

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INTERRUPT_INIT

3-Error

CPP[dec]: 0x[hec] Failed to initialize [chars] interrupt - [chars]

Failed to initialize an interrupt

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_ATTACH

3-Error

CPP[dec]: 0x[hec] FAILED: to attach [chars]

Device Failed to attach

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_UNSUPPORT

3-Error

CPP[dec]: 0x[hec] - unsupported CPP TYPE. CPP TYPE:[dec]

Unsupported CPP TYPE

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INIT

3-Error

0x[hec] Failed to initialize [chars] - [chars]

Failed to init device

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INIT_ID

3-Error

CPP[dec]: 0x[hec] Failed to initialize [chars] - [chars]

Failed to init device

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_CREATE

3-Error

0x[hec] Failed to create [chars] - [chars]

Failed to create device

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_CREATE_ID

3-Error

CPP[dec]: 0x[hec] Failed to create [chars] - [chars]

Failed to create device

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_GET_DETAILS

3-Error

CPP[dec]: 0x[hec] Failed to get [chars] details - [chars]

Failed to get device details

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_ALLOCATE

3-Error

CPP[dec]: 0x[hec] Failed to allocate [chars] - [chars]

Failed to allocate data

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_INTERNAL

3-Error

CPP[dec]: 0x[hec] Internal Error [chars]

Internal coding error.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_CPP_SUBDEV_ACCESS

3-Error

CPP[dec].[dec]: An access error has been reported. Error count [dec].

The system has reported an error while accessing a CPP subdevice

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_MEM_CLEAR

3-Error

CPP[dec]: 0x[hec] Failed to clear memory [chars]

SW failed to clear memory location

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_MEM_WRITE

3-Error

CPP[dec]: 0x[hec] Failed to write to memory [chars]

SW failed to write to a memory location

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_ACQUIRE_LOCK

3-Error

CPP[dec]: 0x[hec] Failed to acquire memory lock [chars]

SW failed to acquire shared memory lock

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_RELEASE_LOCK

3-Error

CPP[dec]: 0x[hec] Failed to release memory lock [chars]

SW failed to release shared memory lock

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-4-HW_REV_OLD

4-Warning

Found HW revision [chars] using [chars] based on [chars]. No customer deployment.

The specified board or chip showed an incorrect invalid or too old hardware revision. That hardware revision was possibly overridden

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_MEM_SIZE

3-Error

CPP[dec]: 0x[hec] Failed to acquire memory size [chars]

SW failed to acquire the size of a block of memory

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-4-ADRSPC_LIMIT

4-Warning

Address space limit [dec] KB reached mapping block [chars] size [dec] dynamically over limit space: [dec] KB

The process indicated tried to map more of the Forwarding Engine's address space than was allocated for it. A slower access method will be used instead. This will lower the performance of some operations which require accesses to the Forwarding Engine

cpp-sw

LOG_STD_SH_TECH_ACTION

CPPDRV-6-ACCTRC8B

6-Information

Access CPP [dec] address 0x%08llX Blk/Off:[chars]/0x%08llX [chars] %3d bytes

A CPP access was traced

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-6-ACCTRC16B

6-Information

Access CPP [dec] address 0x%08llX Blk/Off:[chars]/0x%08llX [chars] %3d bytes

A CPP access was traced

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-4-CORE_TABLE

4-Warning

CPP[dec] specific core dump table '[chars]' not found using minimal fallback table '[chars]' instead

The QFP configuration found on this board did not match any of the tables which define which data has to be collected if a fatal error is detected. Instead a minimal table is used which covers most of the QFP registers. The QFP is fully operational.

cpp-sw

LOG_STD_SH_TECH_ACTION

CPPDRV-3-FATAL_MIN_CPU

3-Error

CPP[dec]: Insufficent number of CPUs detected = [dec] required = [dec]

The current system lacks a sufficent number of CPUs or cores

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-4-CPU_FEATURE

4-Warning

CPP[dec]: CPU lacks feature [chars]. Performance may be sub-optimal.

The currently installed CPU lacks a certain feature that improve performance of the forwarding engine. The QFP is fully operational but may operate at a reduced capacity.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-GUEST_CPU_FEATURE

3-Error

CPP[dec]: Guest CPU lacks feature [chars].

The currently installed Guest CPU lacks a certain feature that is required by the forwarding engine but that feature is supported by the Host CPU. The QFP is operating with normal functionality using the host CPU feature but live migration to a host which lacks this feature will result in a crash.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-3-FATAL_CPU_FEATURE

3-Error

CPP[dec]: CPU lacks feature [chars]. Packet forwarding disabled.

The currently installed CPU lacks a certain feature that is required by the forwarding engine. The QFP is operating with reduced functionality with packet forwarding disabled.

cpp-sw

LOG_STD_NO_ACTION

CPPDRV-4-FUTURE_FATAL_CPU_FEATURE

4-Warning

CPP[dec]: CPU lacks feature [chars] required in a future release.

The currently installed CPU lacks a certain feature that will be required by the forwarding engine in a future release. Caution is advised before upgrading to a newer release to ensure the CPU has the minimum set of CPU features necessary to operate.

cpp-sw

LOG_STD_NO_ACTION

QFP_PLAT-3-PLATFORM_THPUT_MISSING

3-Error

Throughput setting [chars]/[chars] is missing

The throughput property is missing. The forwarding engine cannot operate without a valid throughput.

qfp-driver

LOG_STD_DDTS_TAC_DETAILS

QFP_PLAT-3-PLATFORM_THPUT_INVALID

3-Error

Throughput setting [chars]/[chars] %PRIu64 is invalid

The throughput property is invalid. The forwarding engine cannot operate without a valid throughput.

qfp-driver

LOG_STD_DDTS_TAC_DETAILS

QFP_PLAT-3-PLATFORM_THPUT_MISSING

3-Error

Throughput setting [chars]/[chars] is missing

The throughput property is missing. The forwarding engine cannot operate without a valid throughput.

qfp-driver

LOG_STD_DDTS_TAC_DETAILS

QFP_PLAT-3-PLATFORM_THPUT_INVALID

3-Error

Throughput setting [chars]/[chars] %PRIu64 is invalid

The throughput property is invalid. The forwarding engine cannot operate without a valid throughput.

qfp-driver

LOG_STD_DDTS_TAC_DETAILS

QFP_PLAT-3-PLATFORM_THPUT_MISSING

3-Error

Throughput setting [chars]/[chars] is missing

The throughput property is missing. The forwarding engine cannot operate without a valid throughput.

qfp-driver

LOG_STD_DDTS_TAC_DETAILS

QFP_PLAT-3-PLATFORM_THPUT_INVALID

3-Error

Throughput setting [chars]/[chars] %PRIu64 is invalid

The throughput property is invalid. The forwarding engine cannot operate without a valid throughput.

qfp-driver

LOG_STD_DDTS_TAC_DETAILS

CPPOSLIB-3-INIT_NOTIFY

3-Error

Failed to initialize: [chars]

A function failed to initialize.

cpp-sw

LOG_STD_NO_ACTION

CPPOSLIB-3-ERROR_NOTIFY

3-Error

[chars] encountered an error

Print error message to console

cpp-sw

LOG_STD_NO_ACTION

CPPOSLIB-3-REGISTER_NOTIFY

3-Error

Failed to register: [chars]

A function failed to register.

cpp-sw

LOG_STD_NO_ACTION

CPPOSLIB-3-GET_NOTIFY

3-Error

Failed to get data: [chars]

A function failed to get data.

cpp-sw

LOG_STD_NO_ACTION

CPPOSLIB-3-CLEAN_NOTIFY

3-Error

Failed to cleanup: [chars]

A function failed to cleanup data.

cpp-sw

LOG_STD_NO_ACTION

QFP_XCONNECT-3-XCONNECT_CONFIG_ERR

3-Error

Cannot configure xconnect port-forwarding on [chars] if there are subinterfaces present with VLAN encaps. Remove all subinterface configurations before configuring xconnect port-forwarding.

A main interface cannot be configured for xconnect port-forwarding if subinterfaces with VLAN encaps are present.

-

LOG_STD_NO_ACTION

APPNAV_CLIENT-3-CFT_INIT_FAILED

3-Error

AppNav failed initialize flow table - [dec].

Flow table is a critical component of AppNav. The failure is likely due to lack of memory DRAM on the ESP. The

service-controller

LOG_STD_REDUCE_ACTION

CPP_CONF_SW-4-CPP_CONF_SW_NULL_EXMEM

4-Warning

Unexpected NULL shared-local EXMEM handle - ref_count [dec]

The error will be corrected and pinhole programming will continue.

asr1k-conf-sw

LOG_STD_NO_ACTION

CPPFW-4-NO_MEM_ZP_CG_ARY_CG

4-Warning

[chars]: [chars]: Could not allocate [chars] [dec] bytes x [dec] entries for [dec] bytes of memory zone pair: [dec]:[chars] policy: [dec]:[chars]

Could not allocate an array of memory of the given size and entries. Configuation Failed

iosxe-zbfw

"Configureation is too large for platform." " Attempt to reduce" " size of firewall policy stats etc. " " or disable other features"

CPPFW-4-NO_CLASS_CG

4-Warning

[chars]: Could not locate class [chars] zone_pair id [dec]:[chars] policy: [dec]:[chars] class id: [dec]

Could not Locate class inforamtion. Configuration Failed

iosxe-zbfw

LOG_STD_NO_ACTION

CPPFW-4-NO_CG

4-Warning

[chars] Could not locate class group [chars] zone_pair id [dec]:[chars] cg id: [dec]

Could not class group policy inforamtion. Configuration Failed

iosxe-zbfw

LOG_STD_NO_ACTION

CPPFW-4-NO_FM_STAT_MAP_CG

4-Warning

[chars]: Could not locate fm stat map table: [chars]. zone_pair id: [dec]:[chars] cg: [dec]:[chars]

Could not Locate CPP FM_STAT mapping table. Configuration Failed

iosxe-zbfw

LOG_STD_NO_ACTION

CPPFW-4-WRITE_HW_MEM_FAIL_CG

4-Warning

[chars]: [chars]: [chars]: zone_pair id: [dec]:[chars] policy: [dec]:[chars] class: [chars]

Could not write data to data plane. Configuration Failed

iosxe-zbfw

LOG_STD_NO_ACTION

STILE_CLIENT-4-MAX_LINK_TOUCH_WARN

4-Warning

NBAR number of [chars] threshold is reached can't allocate more memory for [chars].

Because of non-availability of flow links new traffic flows may not be classified properly

qfp-nbar

LOG_STD_NO_ACTION

STILE_CLIENT-4-MAX_LINK_TOUCH_CLEAR

4-Warning

NBAR number of [chars] has declined below its threshold links are available for [chars].

After NBAR was in links shortage the number of links has declined below its threshold. New traffic flows will be classified properly

qfp-nbar

LOG_STD_NO_ACTION

STILE_CLIENT-4-NBAR_MEMORY_BOUNDARY_TOUCH_WARN

4-Warning

NBAR reached maximum configured memory utilization. Can't allocate more memory for [chars].

Because of NBAR memory shortage new flows may not be classified properly

qfp-nbar

LOG_STD_ACTION

STILE_CLIENT-4-NBAR_MEMORY_BOUNDARY_TOUCH_CLEAR

4-Warning

NBAR memory utilization has declined below its threshold memory is available for [chars].

After NBAR was in memory shortage memory utilization has declined below its threshold New traffic flows will be classified properly

qfp-nbar

LOG_STD_ACTION

STILE_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_WARN

4-Warning

System free memory has reached its lower watermark. Can't allocate more memory for [chars].

Because of system memory shortage new flows may not be classified properly

qfp-nbar

LOG_STD_ACTION

STILE_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_CLEAR

4-Warning

System free memory has increased above its lower watermark memory is available for [chars].

After system memory was in shortage free memory has increased above its lower watermark New traffic flows will be classified properly

qfp-nbar

LOG_STD_ACTION

STILE_CLIENT-4-NBAR_NOT_ENOUGH_STATIC_MEMORY

4-Warning

NBAR does not have enough memory to be activated.

System does not have enough free memory to allow activation of NBAR

qfp-nbar

LOG_STD_NO_ACTION

STILE_CLIENT-4-NBAR_ACTIVATION_FAILED

4-Warning

NBAR activation process has failed with errcode [dec].

Activation of NBAR has failed. the cause is provided through the error code from cerrno.h

qfp-nbar

LOG_STD_NO_ACTION

STILE_CLIENT-4-NBAR_GENERAL_FAILED

4-Warning

An error occured with errcode [dec].

An error occured will not handle the messages wait for deactivate the cause is provided through the error code from cerrno.h

qfp-nbar

LOG_STD_NO_ACTION

QFP_FNF-4-FNF_MEM_UPLIMIT_WARN

4-Warning

Netflow and Flexible Netflow configuration is using %PRIu64 bytes

Configured Netflow and Flexible Netflow records are using more than the recomended maximum of total DRAM.

-

LOG_STD_NO_ACTION

QFP_FNF-4-FNF_MEM_UPLIMIT_CLEAR

4-Warning

Netflow and Flexible Netflow configuration is using %PRIu64 bytes

Configured Netflow and Flexible Netflow records are now using less than the recomended maximum of total DRAM.

-

LOG_STD_NO_ACTION

QFP_TUN-3-TUN_MODE_CONFIG_ERR

3-Error

Detected unsupported tunnel mode [chars] configuration.

An unsupported tunnel mode has been configured.

-

LOG_STD_NO_ACTION

CPP_SBC-4-CPP_SBC_NULL_EXMEM

4-Warning

Unexpected NULL shared-local EXMEM handle - ref_count [dec]

The error will be corrected and pinhole programming will continue.

asr1k-sbc

LOG_STD_NO_ACTION

CPP_FM-4-CPP_FM_FIELD_IGNORED

4-Warning

Matching on field type [dec] [chars] value [dec] 0x[hec]

User is trying to use a classification criterion not supported by the feature. For example user is trying to apply a with a class matching matched on an IPv6 ACL that contains a match on flow-label. The entire rule e.g. ACE containing the unsupported criterion

cpp-sw

LOG_STD_NO_ACTION

CPP_FM-3-CPP_FM_TCAM_WARNING

3-Error

TCAM limit exceeded: [chars]

-

-

-

CPP_FM-3-CPP_FM_CLIENT_WARNING

3-Error

Client Is Invalid: [chars]

-

-

-

CPP_FM-4-CPP_FM_TCAM_MORE_INFO_WARNING

4-Warning

TCAM limit exceeded: [chars]

-

-

-

CPP_FM-3-CPP_FM_FIPS_BYPASS_TEST

3-Error

NIST bypass test failed for CPP_FM object [chars].

Classification Feature Manager Security Client database detected a discrepancy in a security sensitive object. This could be due to a hardware or software resouce limitation or a software defect.

qfp-class-internal

"Check the logs for information on the relevant " "object download states. Remove the object or a " "parent object in question. If the problem persists " "reboot the forwarding processor ESP."

QFPPALCI-4-UNEXP_CHIP_REV

4-Warning

QFP[dec].[dec] chip [chars] reported unexpected revision 0x%X using [dec].[dec] instead

The named chip making up part of the QFP engine reported an unexpected chip revision. The system continued running assuming a default revision.

qfp-driver

"Monitor the QFP forwarding engine for stability and performance issues." "If you notice anything unusual copy the error message " "exactly as it appears on the console or in the system log. " "Research and attempt to resolve the error using the Output " "Interpreter " OUTPUT_INTERPRETER ". Also perform a search of the Bug " "Toolkit " BUG_TOOLKIT ". If you still require assistance open a case with" " the Technical Assistance Center via the Internet " TAC_CASE_OPEN " or " "contact your Cisco technical support representative and provide the " "representative with the gathered information."

PALCI-4-FLOWDB_INSUFFICIENT_MEMORY

4-Warning

Allocation of flow database failed due to insufficient memory - [dec] MB. Please increase the memory otherwise the stateful features will not work correctly.

The allocation of flow database failed as there is not enough memory allocated to the system. The memory needs to be increased for stateful features to work correctly

isr9k-dp

"Increase the system memory."

QFP_ETH-3-VLAN_BIND_XCONN_CONFIG_ERR

3-Error

Cannot apply VLAN encap configuration if main interface is configured for xconnect port-forwarding. Check configuration of [chars] remove any xconnect port-forwarding configuration and reapply VLAN encap configuration.

A main interface set in xconnect port-forwarding mode will reject VLAN encap configurations.

-

LOG_STD_NO_ACTION

CFT_CLIENT-4-MAX_FCS_TOUCH_WARN

4-Warning

CFT number of [chars] threshold is reached can't allocate more memory for [chars].

Because of non-availability of flow contexts new traffic flows may not be opened

qfp-cft

LOG_STD_NO_ACTION

CFT_CLIENT-4-MAX_FCS_TOUCH_CLEAR

4-Warning

CFT number of [chars] has declined below its threshold flow contexts are available for [chars].

After CFT was in flow contexts shortage the number of flow contexts has declined below its threshold. New traffic flows will be opened properly

qfp-cft

LOG_STD_NO_ACTION

CFT_CLIENT-4-CFT_MEMORY_BOUNDARY_TOUCH_WARN

4-Warning

CFT reached maximum configured memory utilization. Can't allocate more memory for [chars].

Because of CFT memory shortage new flows may not be opened properly

qfp-cft

LOG_STD_ACTION

CFT_CLIENT-4-CFT_MEMORY_BOUNDARY_TOUCH_CLEAR

4-Warning

CFT memory utilization has declined below its threshold memory is available for [chars].

After CFT was in memory shortage memory utilization has declined below its threshold New traffic flows will be opened properly

qfp-cft

LOG_STD_ACTION

CFT_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_WARN

4-Warning

System free memory has reached its lower watermark. Can't allocate more memory for [chars].

Because of system memory shortage new flows may not be opened properly

qfp-cft

LOG_STD_ACTION

CFT_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_CLEAR

4-Warning

System free memory has increased above its lower watermark memory is available for [chars].

After system memory was in shortage free memory has increased above its lower watermark New traffic flows will be opened properly

qfp-cft

LOG_STD_ACTION

PUNT_INJECT-4-PUNT_ALERT

4-Warning

Punted packets from the dataplane to the control-plane of type [chars] cause# [dec] [chars] - are being dropped

-

-

-

PUNT_INJECT-4-PUNT_ABATE

4-Warning

Punted packets from the dataplane to the control-plane of type [chars] cause# [dec] [chars] - are no longer being dropped

-

-

-

CPPUI-3-ERROR_NOTIFY

3-Error

[chars]

An UI fault has occurred.

-

LOG_STD_ACTION

CPPCDM-3-ERROR_NOTIFY

3-Error

QFP [dec] thread [dec] encountered an error -Traceback= [chars] [chars]

A QFP fault has occurred.

cpp-ucode

LOG_STD_NO_ACTION

CVLA_CLIENT-4-CVLA_MEMORY_BOUNDARY_TOUCH_WARN

4-Warning

CVLA reached maximum configured memory utilization. Can't allocate more memory for [chars].

Because of CVLA memory shortage new flows may not be opened properly

qfp-cvla

LOG_STD_ACTION

CVLA_CLIENT-4-CVLA_MEMORY_BOUNDARY_TOUCH_CLEAR

4-Warning

CVLA memory utilization has declined below its threshold memory is available for [chars].

After CVLA was in memory shortage memory utilization has declined below its threshold New traffic flows will be opened properly

qfp-cvla

LOG_STD_ACTION

CVLA_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_WARN

4-Warning

System free memory has reached its lower watermark. Can't allocate more memory for [chars].

Because of system memory shortage new flows may not be opened properly

qfp-cvla

LOG_STD_ACTION

CVLA_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_CLEAR

4-Warning

System free memory has increased above its lower watermark memory is available for [chars].

After system memory was in shortage free memory has increased above its lower watermark New traffic flows will be opened properly

qfp-cvla

LOG_STD_ACTION

CPPBQS-4-QLIMITEXCEEDED

4-Warning

QFP [dec].[dec] QoS Queue limit [dec] exceeded at [dec].

Max number of QoS queues supported on QFP has been exceeded. Configuration failure is possible causing unpredictable results.

-

"Reduce the size of the QoS configuration"

CPPBQS-4-MAXRATEPROFILELIMITEXCEEDED

4-Warning

QFP [dec].[dec] Max Rate Profile limit [dec] exceeded at [dec].

Max number of Max Rate Profiles supported on QFP has been exceeded. Configuration failure is possible causing unpredictable results.

-

"Reduce the number of unique shape rates in the configuration"

CPPBQS-4-MINRATEPROFILELIMITEXCEEDED

4-Warning

QFP [dec].[dec] Min Rate Profile limit [dec] exceeded at [dec].

Max number of Min Rate Profiles supported on QFP has been exceeded. Configuration failure is possible causing unpredictable results.

-

"Reduce the number of unique bandwidth rates in the configuration"

CPPBQS-6-QLIMITOK

6-Information

QFP [dec].[dec] QoS Queue limit [dec] was exceeded and is now within platform specifications at [dec].

Max number of QoS queues supported on QFP was exceeded. It is now within platform specifications

-

-

CPPBQS-3-QMOVEFAIL

3-Error

CPP [dec] schedule [chars] queue move failed [hex] - SEID=[hex] SID=%#X

A QFP BQS schedule queue move operation failed.

qfp-bqs-internal

LOG_STD_SH_TECH_ACTION

CPPBQS-3-REPARENTFAIL

3-Error

QFP [dec] schedule [chars] reparent failed [hex] - SEID=%#X SID=[hex]

A QFP BQS schedule reparent operation failed.

qfp-bqs-internal

LOG_STD_SH_TECH_ACTION

CPPBQS-4-QMOVEPROC

4-Warning

QFP [dec] schedule [chars] queue move in progress seq [dec]

A QFP BQS schedule queue move operation is not proceeding or is proceeding at a slow rate which can lead to packet drops. The most likely cause of a queue move operation getting stuck is having a rate based queue that has packets enqueued on it that are not being serviced very frequently or being starved due to higher priority queues causing an oversubscription of the physical output interface.

qfp-bqs-internal

"No action is required if QMVOEDONE message" " is also displayed following QMOVEPROC." " If QMOVEDONE message is not displayed or" " you continue to see QMOVEPROC messages" " displayed then collect the data from" " the following show commands:" " show platform" " show platform hardware qfp <active|standby> bqs status" " show platform hardware qfp <active|standby> bqs qmove info" " show platform hardware qfp <active|standby> bqs qmove child" " show platform hardware qfp <active|standby> bqs qmove flush" "Report the problem to the Cisco TAC providing" " the data from the above show commands."

CPPBQS-3-QMOVESTUCK

3-Error

QFP [dec] schedule [chars] queue move operation is not progressing as expected - seq [dec]

A QFP schedule queue move operation is not proceeding as expected and can lead to packet drops. The most likely cause of a queue move operation getting stuck is having a rate based queue that has packets enqueued on it that are not being serviced very frequently or being starved due to higher priority queues causing an oversubscription of the physical output interface.

qfp-bqs-internal

"No action is required if QMVOEDONE message" " is also displayed following QMOVESTUCK." " If a QMOVEDONE or QMOVEPROC message is not" " displayed following QMOVESTUCK then" " collect the data from the following show" " commands:" " show platform" " show platform hardware qfp <active|standby> bqs status" " show platform hardware qfp <active|standby> bqs qmove info" " show platform hardware qfp <active|standby> bqs qmove child" " show platform hardware qfp <active|standby> bqs qmove flush" "Report the problem to the Cisco TAC providing" " the data from the above show commands."

CPPBQS-4-QMOVEDONE

4-Warning

QFP [dec] schedule [chars] queue move done

A QFP BQS schedule queue move operation was not proceeding in a timely manner and flagged as being stuck but has since completed.

cpp-sw

LOG_STD_SH_TECH_ACTION

CPPBQS-4-SRTMEMLOW

4-Warning

QFP [dec] HW [chars]:[chars] schedule resources depleted - [dec]%% available

QFP BQS HW schedule resources have dropped below critical threshold.

qfp-bqs-internal

LOG_STD_REDUCE_ACTION

CPPBQS-3-QMOVEQOSDIS

3-Error

QFP [dec] schedule [chars] queue move to [chars] unsupported QoS disabled

QFP BQS schedule move to new output interface on different subdevice is unsupported. QoS for this schedule is disabled

qfp-bqs-internal

"Restore failed link or route so that schedule " "is moved back and QoS is restored. Or force the " "schedule to fail back to a link that is on " "the same subdevice the this schedule was " "originally on."

CPPBQS-6-QMOVEQOSENA

6-Information

QFP [dec] schedule [chars] queue move to [chars] QoS enabled

QFP BQS schedule that was disabled due to having been moved to an output interface on different subdevice has now moved back to the original subdevice and QoS is now enabled again.

-

-

CPPBQS-4-YODASRTMEMLOW

4-Warning

QFP [dec].[dec] HW [chars]:[chars]:[chars] schedule resources depleted - [dec]%% available

QFP BQS HW schedule resources have dropped below critical threshold.

qfp-bqs-internal

LOG_STD_REDUCE_ACTION

CPPBQS-3-SRT_PERR_RESORT_FAIL

3-Error

QFP [dec] unable to resort to correct parity error at SEID=%#X

A QFP BQS SRT parity error occurred that was uncorrectable

qfp-bqs-internal

LOG_STD_NO_ACTION

CPPBQS-3-MULTICOMMITS

3-Error

Multiple outstanding [chars] commit events detected [dec]

-

-

-

CPPBQS-3-RATE_RATIO_OPTIMIZATION

3-Error

QFP BQS detected invalid rate optimization nodes for [chars]

QFP unable to optimize the rates due to missing optimization nodes

qfp-bqs-internal

"Enable 'platform qos optimize-rate-ratio' command " "before applying QOS."

CPPBQS-6-QMRTDUMP

6-Information

QFP Queue Manager Real-Time trace dump - [chars]

The QFP Queue Manager Real-Time trace data dumping to disk has either started or completed.

-

-

CPPBQS-6-QMRTREPLAY

6-Information

QFP Queue Manager Real-Time event replay [chars] - [chars]

The QFP Queue Manager Real-Time event data replay from disk file status display

-

-

CPPEXMEM-4-LOWMEM

4-Warning

CPP [dec] [chars] memory low - [dec] percent depleted

A CPP memory resource has dropped below a critical level.

-

LOG_STD_NO_ACTION

CPPEXMEM-5-MEM

5-Notice

CPP [dec] [chars] memory recovered - [dec] percent depleted

A CPP memory resource has recovered above the low threshold level.

-

LOG_STD_NO_ACTION

CPPEXMEM-3-NOMEM

3-Error

QFP: [dec] [chars] memory allocation of [dec] bytes by [chars] failed

A request for QFP memory resource allocation has failed due to running out of memory. QFP memory is used by the datapath for packet forwarding.

-

"Display the memory allocation usage" " per feature to determine where most" " of the memory is being used. This can" " help identify where to adjust feature" " scaling. The following CLI will display" " the memory utilization: show platform" " hardware qfp act infrastructure exmem" " statistics user. If the system crashed" " prior to issuing this command you can" " retrieve the information from the binary" " trace log file for the process that " " generated this error message."

CPPEXMEM-3-TOPUSER

3-Error

QFP: [dec] Top User: [chars] [chars]: [dec] Type: [chars]

A request for QFP memory resource allocation has failed due to running out of memory. The top consumer of exmem is provided with this message to possibly identify the source for running out of memory. QFP memory is used by the datapath for packet forwarding.

-

LOG_STD_NO_ACTION

QFPOOR-4-LOWRSRC_PERCENT_WARN

4-Warning

QFP [dec] [chars] at [dec] percent exceeds warning level [dec]

A QFP resource has dropped below a critical level.

-

LOG_STD_NO_ACTION

QFPOOR-2-LOWRSRC_PERCENT_CRIT

2-Critical

QFP [dec] [chars] at [dec] percent exceeds critical level [dec]

A QFP resource has dropped below a critical level.

-

LOG_STD_NO_ACTION

QFPOOR-5-RSRC_PERCENT

5-Notice

QFP [dec] [chars] resource recovered - [dec] percent depleted

A QFP resource has recovered from the critical level.

-

LOG_STD_NO_ACTION

QFPOOR-4-LOWRSRC

4-Warning

QFP [dec] [chars] resource low - [dec] depleted

A QFP resource has dropped below a critical level.

-

LOG_STD_NO_ACTION

QFPOOR-5-RSRC

5-Notice

QFP [dec] [chars] resource recovered - [dec] depleted

A QFP resource has recovered from the critical level.

-

LOG_STD_NO_ACTION

BW_LICENSE-5-THROUGHPUT_THRESHOLD_LEVEL

5-Notice

Average throughput rate exceeded [dec] percent of licensed bandwidth of [chars] during [dec] sampling periods in the last 24 hours sampling period is [dec] seconds

-

-

-

BW_LICENSE-4-THROUGHPUT_MAX_LEVEL

4-Warning

Average throughput rate approached the licensed bandwidth of [chars] during [dec] sampling periods in the last 24 hours sampling period is [dec] seconds

-

-

-

QFPOOR-4-TOP_EXMEM_USER

4-Warning

EXMEM_USER: [chars] Allocations: [dec] Bytes-Alloc: [dec] Bytes-Total: [dec]

TOP QFP Exmem user when resource has dropped below a critical level.

-

LOG_STD_NO_ACTION

CPPHA-7-READY

7-Debug

CPP [dec] loading and initialization complete

A CPP has been successfully loaded and initialized\n\ ready to be configured for forwarding packets.

-

LOG_STD_NO_ACTION

CPPHA-7-START

7-Debug

CPP [dec] [chars]

A CPP is being started.

-

LOG_STD_NO_ACTION

CPPHA-7-SYSREADY

7-Debug

CPP client process [chars] [dec] of [dec] ready.

A CPP Client process has started and registered with\n\ CPP HA Server.

-

LOG_STD_NO_ACTION

CPPHA-6-SYSINIT

6-Information

CPP HA system [chars].

CPP system initialization state.

-

LOG_STD_NO_ACTION

CPPHA-3-INITFAIL

3-Error

CPP [dec] initialization failed - [chars] [hex]

A CPP initialization failed.

cpp-sw

LOG_STD_SH_TECH_ACTION

CPPHA-3-FAILURE

3-Error

CPP [dec] failure [chars] detected

A CPP failure has been detected.

cpp-ucode

LOG_STD_SH_TECH_ACTION

CPPHA-3-FAULTCRASH

3-Error

CPP [dec].[dec] unresolved fault detected initiating crash dump.

A unresolved fault detected initiating crash dump.

-

LOG_STD_SH_TECH_ACTION

CPPHA-3-FAULT

3-Error

CPP:[dec].[dec] desc:[chars] det:[chars] class:[chars] sev:[chars] id:[dec] cppstate:[chars] res:[chars] flags:0x[hec] cdmflags:0x[hec]

A CPP fault has occurred.

cpp-ucode

LOG_STD_NO_ACTION

CPPHA-3-FAULTRATE

3-Error

CPP:[dec].[dec] desc:[chars] det:[chars] class:[chars] sev:[chars] id:[dec] cppstate:[chars] res:[chars] flags:0x[hec] cdmflags:0x[hec]

A CPP fault has occurred.

cpp-ucode

LOG_STD_NO_ACTION

CPPHA-3-CDMDONE

3-Error

CPP [dec] microcode crashdump creation completed.

The CDM has completed generating microcode crashdump.

-

LOG_STD_SH_TECH_ACTION

CPPHA-3-NOCDM

3-Error

CPP [dec] CDM not running.

The CDM process is not running.

-

LOG_STD_SH_TECH_ACTION

CPPHA-3-BULKSYNC

3-Error

bulk sync processing failed to complete

-

-

-

CPPHA-3-EXMEMBIND

3-Error

bind to exmem failed to complete

-

-

-

CPPHA-3-EXMEMALLOC

3-Error

exmem allocation failed

-

-

-

CPPHA-3-FDBQUERY

3-Error

[chars] FDB query failed [dec] [chars]

-

-

-

CPPHA-3-CHUNKCREATE

3-Error

Chunk Create failed [dec]

-

-

-

CPPHA-3-CHUNKALLOC

3-Error

Chunk allocation failed [dec]

-

-

-

CPPHA-3-CHUNKFREE

3-Error

Chunk free failed [dec]

The CPP bulk synchronization processing failed on the standby.

-

LOG_STD_SH_TECH_ACTION

TRACEKEY_TEST-3-TRACEKEY

3-Error

This is a simulated message for errmsg: test_errno=[dec] [chars]:

-

-

-

TRACEKEY_TEST-3-TRACEKEY

3-Error

This is a simulated message for errmsg: test_errno=[dec] [chars]:

-

-

-

EXIT_HANDLER-1-CRASHINFO

1-Alert

signo=[dec]

-

-

-

BCM3142-3-LATE_MAP_FLUSH_INT

3-Error

Mg[dec] Rcvr [dec] lch [dec]: LATE_MAP_FLUSH interrupt received from BCM3142 reg_mask_lo [hec] reg_mask_hi [hec] reg_count [dec] resend_mask_lo [hec] resend_mask_hi [hec] resend_count [dec]

A receiver LATE_MAP_FLUSH interrupt was received from the BCM3142.

cmts-infra

"Shut and not shut the upstream"

DC-4-FILE_OPEN_WARNING

4-Warning

Not able to open [chars]

The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles.

dc

" Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. "

DC-3-PATTERN_NOT_FOUND

3-Error

[chars]

The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reload the Device Pr/scratch/stevenl/polaris/wab_amur_eedge_polaris/novaofiles file to the flash and re-enable the device classifier"

DC-3-INCOMPATIBLE_PROFILE_VERSION

3-Error

Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec]

An incompatible profile version is detected. The device classifier feature will be operationally down.

dc

"Reload the expected version of device profiles file to the " "system and re-enable the device classifier "

DC-3-BUILTIN_INIT_FAIL

3-Error

[chars]

Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-6-DEFAULT_INIT_INFO

6-Information

[chars]

The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles.

dc

LOG_STD_ACTION

DC-3-SM_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Registraton of Device classifier with SM failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-OUI_INIT_FAIL

3-Error

OUI Table initialization failed for [chars]

Loading of the OUI databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-CHECK_INIT_FAIL

3-Error

[chars]

Loading of the Checks databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-DB_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Initilization of Device classifier Internal database failed So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-MAX_RULES_EXCEEDED

3-Error

[chars].

The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_PROFILES_EXCEEDED

3-Error

total profiles [dec] exceeds the max supported [dec]

The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_OUI_EXCEEDED

3-Error

[chars].

The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-NO_MEM

3-Error

[chars].

There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Increase the memory size in the system and " "re-enable the device classifier"

DC-3-DC_DISABLED

3-Error

[chars].

The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles

dc

"The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier"

DC-3-SM_UPDATE

3-Error

Failed to update [chars].

Internal error occured during device classification . This may cause the device to be unknown.

dc

-

DC-3-SM_API

3-Error

[chars] return [chars].

Internal error returned by Session Manager api.

dc

-

DC-3-FILE_READ_ERROR

3-Error

Error [chars] the profile file: [chars]

There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-FILE_CHECKSUM

3-Error

Checksum [chars] failed for the profile file: [chars]

Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-SM_GET

3-Error

Failed to get [chars].

Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results.

dc

-

DC-3-DISABLE_FAIL

3-Error

Failed to disable DC.

Internal error occured trying to disable Device Classifier.

dc

"Please run the command: show macro auto monitor clients and try disabling" "the clients"

DC-3-ENABLE_FAIL

3-Error

Failed to enable DC.

Internal error occured trying to enable Device Classifier.

dc

"Please check the previous DC error messages and take the relevant action"

DC-3-HRPC_SYNC

3-Error

Error on member switch [dec] error_code = [dec]

Internal error occured while trying to sync Device Classifier.state

dc

"Please check the state of the stack members"

DC-3-DC_ADD_USR_CHK

3-Error

Addition of custom checks failed : [chars].

Internal error returned during addition of custom checks.

dc

-

DC-3-DC_ADD_USR_RULE

3-Error

Addition of custom rules failed : [chars].

Internal error returned during addition of custom rules.

dc

-

DC-3-DC_ADD_USR_PROFILE

3-Error

Addition of custom profiles failed : [chars].

Internal error returned during addition of custom profiles.

dc

-

KEYSTORE_AE46C1-6-SELF_TEST_PASS

6-Information

Keystore pass power on self test

keystore pass power on self test for both SHA1 and HMAC-SHA1

-

-

KEYSTORE_AE46C1-3-SELF_TEST_FAILURE

3-Error

Keystore power on self test failure. [chars]

keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state.

-

"Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced."

KEYSTORE_AE46C1-6-RANDOM

6-Information

A pseudo-random number was generated twice in succession[dec].

A pseudo-random number generator produced the same number twice\n\ in succession.

-

"Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative."

KEYSTORE-3-IFS_OPEN_W

3-Error

Failed to open file \[chars]\ for writing software keystore. [chars]

An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_WRITE

3-Error

An error occurred while writing to the software keystore file.

CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_OPEN_R

3-Error

Failed to open file \[chars]\ for reading software keystore. [chars]

An error occurred while opening the keystore file for reading. CTS keys could not be retrieved.

-

-

KEYSTORE-3-IFS_READ

3-Error

An error [chars] occurred while reading from the software

CTS keys could not be retrieved from persistent storage.

-

-

KEYSTORE-3-BAD_MAGIC

3-Error

Bad magic number 0x%08x in software keystore file \[chars]\.

Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-UNEXPECTED_EOF

3-Error

Unexpected end of file while reading software keystore \[chars]\.

Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-IPCPORT

3-Error

Failed to create IPC port [chars] for keystore redundancy. [chars].

An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCOPEN

3-Error

Failed to open IPC port to peer for keystore redundancy: [chars]

An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCNOCONN

3-Error

No IPC communication path to peer available for keystore [chars].

No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCSEND

3-Error

IPC send error [chars] while sending [chars].

An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-ISSU_INCOMPAT

3-Error

Standby incompatible for SSO.

The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode.

-

-

KEYSTORE-3-IPC_NO_PROC

3-Error

Could not create a process to receive keystore redundancy messages.

An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-NO_KEYSTORE

3-Error

CTS hardware keystore is not responsive and software emulation is not enabled.

The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore.

-

-

KEYSTORE-3-IFS_OPEN_W

3-Error

Failed to open file \[chars]\ for writing software keystore. [chars]

An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_WRITE

3-Error

An error occurred while writing to the software keystore file.

CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_OPEN_R

3-Error

Failed to open file \[chars]\ for reading software keystore. [chars]

An error occurred while opening the keystore file for reading. CTS keys could not be retrieved.

-

-

KEYSTORE-3-IFS_READ

3-Error

An error [chars] occurred while reading from the software

CTS keys could not be retrieved from persistent storage.

-

-

KEYSTORE-3-BAD_MAGIC

3-Error

Bad magic number 0x%08x in software keystore file \[chars]\.

Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-UNEXPECTED_EOF

3-Error

Unexpected end of file while reading software keystore \[chars]\.

Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-IPCPORT

3-Error

Failed to create IPC port [chars] for keystore redundancy. [chars].

An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCOPEN

3-Error

Failed to open IPC port to peer for keystore redundancy: [chars]

An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCNOCONN

3-Error

No IPC communication path to peer available for keystore [chars].

No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCSEND

3-Error

IPC send error [chars] while sending [chars].

An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-ISSU_INCOMPAT

3-Error

Standby incompatible for SSO.

The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode.

-

-

KEYSTORE-3-IPC_NO_PROC

3-Error

Could not create a process to receive keystore redundancy messages.

An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-NO_KEYSTORE

3-Error

CTS hardware keystore is not responsive and software emulation is not enabled.

The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore.

-

-

EPM-6-POLICY_REQ

6-Information

IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars]

This message indicates that a policy application/remove request has been\n\ received by the EPM

pem

"No action required"

EPM-6-POLICY_APP_SUCCESS

6-Information

Policy Application succeded for Client [[chars]] MAC [[enet]] AuditSession ID [[chars]] for POLICY_TYPE [[chars]] POLICY_NAME [[chars]]

This message indicates that the displayed policy for the client has been\n\ applied successfully by the EPM

pem

"No action required"

EPM-4-POLICY_APP_FAILURE

4-Warning

Policy Application Failed for Client [[chars]] MAC [[enet]] AuditSessionID [[chars]] for POLICY_TYPE [chars] POLICY_NAME [chars] REASON [chars]

This message indicates that the displayed policy for the client\n\ could not be applied by the EPM

pem

"Policy application failure could happen due to multiple reasons.The \n\ reason for the failure is notified to the client and the client has to\n\ take appropriate action based on it"

EPM-6-AAA

6-Information

POLICY [chars]| EVENT [chars]

This message indicates a download request has been sent/downloaded\n\ successfully for the specified dACL

pem

"No action required"

EPM-6-ACL_CONFIG_ERROR

6-Information

ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]'

This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration

pem

"Change ACE configuration for the specifed ACL"

EPM-6-IPEVENT

6-Information

IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars]

This message indicates the IP event Wait/Release/Assignment that\n\ has occured with respect to the specified host

pem

"No action required"

EPM-6-AUTH_ACL

6-Information

POLICY [chars]| EVENT [chars]

This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed

pem

"No action required"

AAAA-3-BADSTR

3-Error

Bad accounting data: [chars]

During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-ACCTDUMP

3-Error

dump of accounting data:

The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-ACCTATTR

3-Error

last accounting attribute:

The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged.

AAA

LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting"

AAAA-3-BADAUTHENSTR

3-Error

Bad authentication data: [chars]

The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size.

AAA

LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication"

AAAA-3-NULUSR

3-Error

accounting for null user

This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-NULPORT

3-Error

Could not establish port information

This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-RELOGIN

3-Error

sanity check in re-login [chars] to [chars]

A software or hardware error occurred.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-DROPACCTSNDFAIL

3-Error

Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars]

An attempt to send an accounting record to a server failed.

aaa

"Check that the server TACACS+ or RADIUS is operational. Next "

AAAA-3-DROPACCTLOWMEM

3-Error

Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars]

An accounting record dropped due to low memory.

aaa

"Disable periodic accounting if it is on. Try to reduce the load " "on the router."

AAAA-3-DROPACCTFULLQ

3-Error

Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]

An accounting record was dropped because there are too many accounting packets enqueued.

aaa

"Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high."

AAAA-3-DROPACCTQUEUEEXCEEDED

3-Error

accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\

An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.

aaa

"Disable periodic accounting if it is on. " "<CmdBold>[no] aaa accounting update newinfo " "periodic <interval><NoCmdBold>"

AAAA-3-MKTIMERFAIL

3-Error

Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records.

Failed to malloc a timer struct for periodic accounting.

aaa

"Free up some memory and have user re-authenticate."

AAAA-3-MKTIMERINVALID

3-Error

Invalid request to create periodic accounting timer for user [chars]. Timer already exists.

Invalid client usuage of timer struct for periodic accounting.

aaa

"Copy the error message exactly as it appears and report it to your " "technical support representative."

AAAA-3-PERIODICFORKFAIL

3-Error

Failed to start periodic accounting process. Periodic accounting records may not be sent.

Failed to create the periodic accounting process.

aaa

"Free up some memory."

AAAA-3-ACCTFORKFAIL

3-Error

Failed to start accounting process. Accounting records may not be sent.

Failed to create the accounting process.

aaa

"Free up some memory."

AAAA-3-AAAFORKFAIL

3-Error

Failed to start AAA process. AAA requests may not be processed.

Failed to create the AAA process.

aaa

"Free up some memory."

AAAA-4-BADMETHNAME

4-Warning

Bad [chars] method-list name \[chars]\ please choose another name

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-ILLEGALNAME

3-Error

Illegal [chars] [chars] name \[chars]\ rejected

A method-list name should not be the same as a method name. Please choose a different name for the method list.

aaa

"Pick a different method-list name that is not also a method-name."

AAAA-3-BADLIST

3-Error

%% AAA: bad [chars] list [chars]

One of the AAA methods does not seem to have a list associated with it.

aaa

LOG_STD_ACTION

AAAA-4-UNSUPWAITSTART

4-Warning

%% AAA: Unsupported option wait-start mapped to start-stop.

wait-start accounting is not supported. It is being mapped to start-stop

aaa

"wait-start accounting is not supported. It is being mapped to start-stop"

AAAA-3-INVALIDLIST

3-Error

%% AAA: invalid [chars] list [dec].

One of the AAA methods lists has inconsistent settings

aaa

LOG_STD_ACTION

AAAA-3-BADARG

3-Error

%% AAA: bad argument %0#4x

We tried to NVGEN a non-existent AAA command.

aaa

LOG_STD_ACTION

AAAA-3-BADSTATE

3-Error

\n%% AAA: Bad state for [chars] list name [dec]

A AAA method list is neither default nor named. This is bad.

aaa

LOG_STD_ACTION

AAAA-3-NOFREELISTS

3-Error

%% AAA: No free [chars] lists for \[chars]\

You have reached the maximum number of possible authentication lists for this method.

aaa

LOG_STD_RECUR_ACTION

AAAA-3-TIMERNOPER

3-Error

AAA/ACCT/TIMER: No periodic update but timer set.

We are trying to free a timer but the update method is not PERIODIC and so no timer should exist.

aaa

LOG_STD_ACTION

AAAA-3-PERNOTIMER

3-Error

AAA/ACCT/TIMER: Periodic update but no timer.

We are trying to free a timer and the method is PERIODIC but no timer seems to exist.

aaa

LOG_STD_ACTION

AAAA-3-OVERWRITE

3-Error

Overwrote internal buffer space [chars]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-DLRFORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

LOG_STD_ACTION

AAAA-3-STRCREATE

3-Error

str_create overwrote its internal buffer.

An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory.

aaa

LOG_STD_ACTION

AAAA-6-ACCTSTART

6-Information

[chars]

A AAA accounting start message.

aaa

"This information is for information only."

AAAA-6-ACCTSTOP

6-Information

[chars]

A AAA accounting stop message.

aaa

"This information is for information only."

AAAA-6-ACCTWATCH

6-Information

[chars]

A AAA accounting watchdog/update message.

aaa

"This information is for information only."

AAAA-3-SUBTYPE

3-Error

Bad Subtype [dec] for \[chars]\ [dec]

An internal software error.

aaa

"Report to tac@cisco.com."

AAAA-3-NOLIST

3-Error

[chars]: no method list-name.

An internal software error.

aaa

LOG_STD_ACTION

AAAA-3-INVSTATE

3-Error

[chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec]

One of the two mentioned data-structures is not set but is needed here. This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-LISTCREATE

3-Error

The list [dec] for [chars] is NULL. This should never be.

One of the method-lists created at startup wasn't created. This may cause a reload

aaa

LOG_STD_ACTION

AAAA-3-NOSERV

3-Error

No name for servergroup in method [chars]

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-4-SERVUNDEF

4-Warning

The server-group \[chars]\ is not defined. Please define it.

A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use.

aaa

"Define the server-group before using it."

AAAA-4-SERVNOTACPLUS

4-Warning

The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a tacacs+ server-group."

AAAA-4-SERVNORADIUS

4-Warning

The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group.

The protocol used by the server-group doesn't support the configured aaa action.

aaa

"Use a radius server-group."

AAAA-4-DNISGPUNDEF

4-Warning

Warning: DNIS group [chars] is not defined.

The DNIS group was used without defining it first. It should be defined before use.

aaa

"Define the DNIS group before using it."

AAAA-3-NOREG

3-Error

[chars] method [dec] has no registry!

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADREG

3-Error

Illegal registry call.

An internal software error has occurred

aaa

LOG_STD_ACTION

AAAA-3-BADCOMM

3-Error

Trying config command but should not be.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-3-NOSG

3-Error

No server-group passed through parser.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-6-SERVERMSG

6-Information

[chars] [chars]: [chars]

This message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-6-ADMINMSG

6-Information

[chars] [chars]: [chars]

This administrative message was passed to the NAS from the AAA server

aaa

"No action need be taken but the message may " "contain usefull information regarding some event " "on the server"

AAAA-3-ILLSGNAME

3-Error

Illegal server-group name [chars] type [chars].

The given server-group name is a name that could conflict with internally chosen lists.

aaa

"Please pick a different server-group name."

AAAA-4-NOSERVER

4-Warning

Warning: Server [chars] is not defined.

The given server is not on the master-list and should be defined or unexpected things might happen.

aaa

"Please define the server on the appropriate " "master-list as soon as possible."

AAAA-4-BADSGNAME

4-Warning

Bad server-group name [chars] type [chars].

The given server-group name either doesn't exist or the given type does not match the defined server-group.

aaa

"Verify that the group exists and has the same " "type."

AAAA-4-BADSGTYPE

4-Warning

Server-group [chars] is not of type [chars].

The given server-group name does not match the specified type

aaa

"Verify that the group exists and has " "the same type."

AAAA-4-SERVNOGRP

4-Warning

Warning: Server [inet]:[dec][dec] is not part of server group [chars].

The server does not belong to the specified server group

aaa

"Please check that the specified server belongs " "to the server group"

AAAA-3-NOADMINPROC

3-Error

[chars]

Administrative process has been enabled but somehow could not run

-

-

AAAA-3-INTERNAL_ERROR

3-Error

[chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-3-SGDUPFREE

3-Error

Duplicate free of server group 0x[hec]

This is an internal software error.

aaa

LOG_STD_ACTION

AAAA-4-NOCACHEPROC

4-Warning

The aaa cache process is not created. Please configure aaa cache profile first

Cache was listed in a method-list without defining it first. Cache profile should be defined before use.

aaa

"Define the cache profile before using it."

AAAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAAA-4-CLI_DEPRECATED

4-Warning

[chars]

CLI deprecated. New CLI to be used

aaa

LOG_STD_ACTION

AAA-3-BADMETHOD

3-Error

Cannot process [chars] method [dec]

A method list function encountered a method list that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADMETHODERROR

3-Error

Cannot process [chars] method [chars]

A method list function encountered a method type that was unknown or could not be handled.

aaa

LOG_STD_ACTION

AAA-3-BADSERVERTYPEERROR

3-Error

Cannot process [chars] server type [chars]

A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration.

aaa

"Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION

AAA-2-FORKFAIL

2-Critical

Cannot fork process [chars]

Attempted to fork a process and failed. The reason could be either hardware or software.

aaa

LOG_STD_ACTION

AAA-2-AAAMULTILINKERROR

2-Critical

[chars]%08X: Acct db for Id %08X absent

AAA internal error

aaa

LOG_STD_ACTION

AAA-3-SORTFAIL

3-Error

[chars] :Peruser Could not sort the [chars] attributes

Sorting of the attributes received from AAA server failed.

aaa

LOG_STD_ACTION

AAA-3-INVALIDATTRLIST

3-Error

aaa attribute list CLI is not valid when configuring in sub-mode.

An internal error has occurred

aaa

LOG_STD_ACTION

AAA-3-ISDNINTF

3-Error

[chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\

Configuration can not be applied to individual ISDN channels.

aaa

"You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide."

AAA-3-AUTHORMLISTUNDEF

3-Error

Authorization method list '[chars]' is not defined. Please define it.

A given method list was listed in a command without defining it first. The method list should be defined before use.

aaa

"Define the method list before using it."

AAA-3-PARSEERR

3-Error

Error[dec] parser is unable to parse [chars] per-user command

All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error.

parser and aaa

"The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative."

AAA-6-ACCTSESSIDWRAP

6-Information

Accounting-Session-ID [dec] exceeded max value allowed

Accounting-Session-ID value exceeded max value allowed. Now it is wrapping.

aaa

"This is informational only not an error."

AAA-3-PASSWDRESTRICTERR

3-Error

AAA password restriction failed.- [chars]\n

The password/secret/key entered is not meeting the password restrictions configured

aaa

LOG_STD_ACTION

AAA-3-BADCURSOR

3-Error

invalid cursor index [dec] max [dec] service [chars] protocol [chars]

A AAA client has provided an invalid attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-MLIST_TOO_MANY_METHODS

3-Error

method list '[chars]'

This is an internal software error. An AAA client attempted to add too many methods to a method list.

aaa

"This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative."

AAA-3-SG_INTERNAL_ERROR

3-Error

server group '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter <CmdBold>Show tech-support" "<NoCmdBold> command collect all the information " "and error message report it to your technical " "support representative."

AAA-3-SG_DEADTIME_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter <CmdBold>Show tech-support<NoCmdBold> " "command collect all the information and error " "message and report it to your technical support " "representative."

AAA-3-SG_TESTPROC_FORKFAIL

3-Error

Failed to fork process for [chars].

Quite likely we ran out of memory. Other explanations are possible.

aaa

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-MLIST_INTERNAL_ERROR

3-Error

method list '[chars]': [chars]

This is an internal software error.

aaa

LOG_STD_ACTION

AAA-3-SERVER_INTERNAL_ERROR

3-Error

Server '[chars]': [chars]

This is an internal software error in the AAA server group subsystem.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-ATTRFORMATERR

3-Error

Attribute with unknown format [dec]

An attribute was found with an invalid format.

aaa

"Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-NULLCURSOR

3-Error

Null cursor

A AAA client has provided a nonexistent attribute cursor to AAA.

aaa

LOG_STD_ACTION

AAA-3-NOTABLE

3-Error

AAA ID [dec]

Resource failure.

aaa

LOG_STD_ACTION

AAA-3-BADLIST

3-Error

invalid list AAA ID [dec]

A AAA client has provided an invalid attribute list to AAA.

aaa

LOG_STD_ACTION

AAA-6-BADHDL

6-Information

invalid hdl AAA ID [dec] hdl [hec] [chars]

A AAA client has provided an invalid attribute list handle to AAA.

aaa

LOG_STD_ACTION

AAA-3-IPILLEGALMSG

3-Error

Invalid use of ip_pid[dec]

This error means a process sent an illegal message.

-

"If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-INVALIDPARM

3-Error

invalid parameter was used when accessing AAA function

A AAA client tried to use a AAA function with an invalid parameter.

aaa

LOG_STD_ACTION

AAA-3-BADMAGIC

3-Error

Data structure failed magic number sanity check

A corrupted data structure has been found which was stored internally.

aaa

LOG_STD_ACTION

AAA-3-BUFFER_OVERFLOW

3-Error

Radius I/O buffer has overflowed

An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.

aaa

"This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter <CmdBold>Show tech-support<NoCmdBold> command " "Collect all the information and error message and report " "it to your technical support representative."

AAA-3-DROPACCTFAIL

3-Error

Accounting record dropped send to server failed: [chars]

An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly.

aaa

"Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter <CmdBold>show running-" "config<NoCmdBold> command contact your cisco technical " "support representative and provide all the information " "gathered to the representative."

AAA-3-AUTH_LOW_IOMEM

3-Error

RADIUS process is unable to handle the requests due to insufficient I/O memory

RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure.

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_PROC_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_IO_MEM_TRASH

3-Error

AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records

Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_UNKNOWN_REASON_TRASH

3-Error

AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records

Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed

aaa

LOG_STD_ACTION

AAA-3-ACCT_LOW_MEM_UID_FAIL

3-Error

AAA unable to create UID for incoming calls due to insufficient processor memory

Stop creating the AAA UID due to LOW processor memory

aaa

LOG_STD_ACTION

AAA-3-LOW_MEM

3-Error

[chars] process is unable to handle the incoming packet due to low memory

Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory.

aaa

LOG_STD_ACTION

AAA-3-ACCT_IOMEM_LOW

3-Error

AAA ACCT process suspended : low I/O memory

AAA ACCT process has been suspended due to insufficient IO memory.

aaa

LOG_STD_ACTION

AAA-5-USER_LOCKED

5-Notice

User [chars] locked out on authentication failure

User locked out since the number of authentication failures exceeded the configured threshold.

aaa

LOG_STD_ACTION

AAA-5-USER_UNLOCKED

5-Notice

User [chars] unlocked by [chars]

User unlocked by the system administrator. User is enabled to login to the system.

aaa

LOG_STD_ACTION

AAA-5-USER_RESET

5-Notice

User [chars] failed attempts reset by [chars]

User's number of failed authentication attempts so far has been reset to zero

aaa

LOG_STD_ACTION

AAA-3-NULLVRF

3-Error

Null vrf entry

A NULL VRF entry found while comparing the AAA VRF attributes.

aaa

LOG_STD_ACTION

AAA-6-INVALIDROUTE

6-Information

Syntax error in route statement: [chars]

Currently downloading route contains syntax error.

aaa

LOG_STD_ACTION

AAA-3-HA_INIT_FAILURE

3-Error

High availability initialization failure: [chars]

The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-3-HA_INTERNAL_ERROR

3-Error

High availability internal error for unique id 0x%8x: [chars]

The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate.

aaa

LOG_STD_ACTION

AAA-6-USER_BLOCKED

6-Information

Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication

\nNone method authentication is not allowed in CLI

aaa

LOG_STD_ACTION

AAA-6-USER_FAIL_VIEW_AAA

6-Information

User [chars] failed to enter view '[chars]'.

You have provided wrong User ID or Password for the requested view

aaa

"This message is for information only. No action" " is required."

AAA-6-SKIP_MOH_ATTRIBUTE

6-Information

Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization.

\nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes.

aaa

LOG_STD_ACTION

SM-4-STOPPED

4-Warning

Event '[chars]' ignored because the state machine is stopped: [chars] [chars]

An attempted was made to post an event to a state machine that has \ already been stopped.

sm

LOG_STD_SH_TECH_ACTION

SM-4-BADEVENT

4-Warning

Event '[chars]' is invalid for the current state '[chars]': [chars] [chars]

An attempt was made to post an event to a state machine that is invalid \ for the current state.

sm

LOG_STD_SH_TECH_ACTION

SM-4-PERSIST

4-Warning

Persistent event '[chars]' did not leave the current state '[chars]': [chars] [chars]

An attempt was made to post a persistent event to a state machine that \ would cause an infinite loop in the current state.

sm

LOG_STD_SH_TECH_ACTION

SM-4-INIT

4-Warning

Internal error while initializing state machine '[chars]' state '[chars]': [chars]

An attempt was made to initialize an invalid state machine.

sm

LOG_STD_SH_TECH_ACTION

SM-4-INIT

4-Warning

-

-

-

-

DEAD-4-SCARLET

4-Warning

* Interface [chars]: I knew without asking she was into the blues

-

-

-

DEAD-4-SCARLET

4-Warning

-

-

-

-

-

4-Warning

fmt \static message_stats_ptr fac ## _ ## name ## _stat_redir_ptr __crb_sysrgn

-

-

-

-

4-Warning

fmt

-

-

-

-

4-Warning

fmt

-

-

-

LOGGER-3-TEST1

3-Error

Non rate limited message test

-

-

-

LOGGER-3-TEST2

3-Error

Rate limited message test

-

-

-

LOGGER-3-TEST1

3-Error

Non rate limited message test

-

-

-

LOGGER-3-TEST2

3-Error

Rate limited message test

-

-

-

CGM-3-CGM_FIPS_BYPASS_TEST

3-Error

NIST bypass test failed for CGM object [chars].

Class-Group Manager Security Client database detected a discrepancy in a security sensitive object. This could be due to a hardware or software resource limitation or a software defect.

qfp-class-internal

"Check the logs for information on the relevant " "object download states. Remove the object or a " "parent object in question. If the problem persists " "reboot the forwarding processor ESP."

CGM-3-CGM_FIPS_BYPASS_TEST

3-Error

-

-

-

-

DIGISIGN-4-SIGNATURE_NOT_PRESENT

4-Warning

%%WARNING: Digital signature is not found in file [chars]\n

The specified image file does not have a digital signature. Only Cisco IOS Software Images are digitally signed. If you enter <CmdBold>verify<NoCmdBold> <CmdBold>copy<NoCmdBold> or <CmdBold>reload<NoCmdBold> command and the specified file is not a digitally signed Cisco IOS Software Image the system displays this warning message because the file does not have a signature. A valid digital signature ensures the integrity of the image.

digi-sign-infra

"If the specified file is an unsigned Cisco IOS Software image " "be cautious when deciding " "whether or not to use this file. The system will not boot using " "this image."

DIGISIGN-3-VERIFICATION_FAILED

3-Error

%%ERROR: Digital signature verification failed for file [chars]: [chars]\n

Validation failure while verifying the digital signature.

digi-sign-infra

"Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered."

DIGISIGN-3-KEY_NOT_FOUND

3-Error

%%ERROR: No keys found for verifying the digital signature in file [chars]

No keys found in the device key storage for validating the digital signature. A valid key is needed to validate the digital signature in the image.

digi-sign-infra

"The device does not have a vlaid key to verify the digital" "signature. Open a case with the Technical Assistance Center" "via the internet at" "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered."

DIGISIGN-3-INVALID_SIGNATURE

3-Error

%%ERROR: Digital signature is not valid for file [chars]: [chars]\n

The specified Cisco IOS Software image has an invalid digital signature. A valid digital signature ensures the integrity of the image.

digi-sign-infra

"Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered."

DIGISIGN-4-INVALID_KEY

4-Warning

%%WARNING: Digital signature verification failed for file [chars]: [chars]\n

Validation failure due to invalid key while verifying the digital signature.

digi-sign-infra

"Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "device information you have gathered."

DIGISIGN-2-MISMATCH_KEYS

2-Critical

%%CRITICAL: System identified a mismatch between the show version output and the key type used in signing. [chars] is a signed [chars] software\n

System identified a mismatch in software type. This might be a modified software.

digi-sign-infra

"Do not use this file. The file might be corrupted or modified." "Open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "image and version information you have gathered."

DIGISIGN-3-DEVIMAGE_NOSUPPORT

3-Error

Cannot verify [chars] as it is signed with special key\n

The software image cannot be verified because it is signed with a special key.

digi-sign-infra

"To allow booting a specially-signed image use the" "software authenticity special command"

DIGISIGN-4-DEVIMAGE_CFG_NOSUPPORT

4-Warning

[chars] signed with special key will not be booted\n

With this configuration enabled the system will be unable to boot software that is signed with a special key.

digi-sign-infra

"Use the [no] form of this configuration no software authenticity special"

DIGISIGN-6-KEY_UPGRADE

6-Information

[chars]\n

System identified a key version mismatch between the key which was used to sign the image and the keys stored on the device

digi-sign-infra

"If the image is signed with a key version newer than the device" "keys then follow the procedure for key revocation which is" "which is documented at cisco.com. If the image is signed with a" "key version that is now obsolete please obtain the latest signed" "copy of this image from cisco.com"

DIGISIGN-3-INVALID_ENVELOPE

3-Error

%%ERROR: Failure in processing signature envelope for system image: [chars]\n

The loaded Cisco IOS software image has an invalid digital signature envelope. A valid digital signature envelope ensures the integrity of the image. The loaded Cisco IOS software image might be corrupted or modified. The failure type is one of the following: 1 Signature envelope version is not supported

digi-sign-infra

"Do not use this file. The file might be corrupted or modified." "Please attempt to copy the file again or download the file again " "from the http://www.cisco.com page before copying it." "If you continue to get this error message open a case with" "the Technical Assistance Center via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl and " "contact your Cisco technical support representative with the " "image and version information you have gathered."

DIGISIGN-4-FUR_BOOT

4-Warning

Field upgradable rommon used for key revocation\n

System identified that the field upgradable rommon was used to boot the image. It is recommended that the readonly rommon be used for the key revocation process.

digi-sign-infra

"Recommended action is to boot the image used for key revocation process " "with readonly rommon. This is a warning message." "Command/process will still go through in the current state."

DIGISIGN-3-OBSOLETE_SW

3-Error

[chars] software signed using obsolete key [chars]\n

System identified that a software was signed using an obsolete key. Key revocation cannot be possible when the system is still using a software signed using an obsolete key.

digi-sign-infra

"Please obtain the latest signed copy of this " "software from cisco.com and upgrade the system module."

DIGISIGN-3-NET_BOOT

3-Error

Netbooted software used for key revocation\n

System was netbooted using a software in a remote device. It is recommended to boot the system using a software in the local device for the key revocation process.

digi-sign-infra

"Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation."

DIGISIGN-3-WPG_BOOT

3-Error

Key revocation not allowed while running warm upgraded software\n

System was booted using warm upgrade. Key revocation process is not supported when the system is booted using warm upgrade. It is recommended to cold boot the system using a software in the local device for the key revocation process.

digi-sign-infra

"Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation."

DIGISIGN-4-DEV_IMAGE

4-Warning

[chars] software signed using special key version [chars]\n

System identified that a software was signed using special key. If this is unintentional please obtain the latest signed copy of the production software from cisco.com and upgrade the system module.

digi-sign-infra

"Get the latest signed copy of production image from cisco.com and upgrade " "the respective module"

DPP_SYSLOG-3-EVENT_ERR

3-Error

Pipeline event - [chars] [chars]

Output to syslog from pipeline

-

""

DPP_SYSLOG-4-EVENT_WARNING

4-Warning

Pipeline event - [chars] [chars]

Output to syslog from pipeline

-

""

DPP_SYSLOG-6-EVENT_INFO

6-Information

Pipeline event - [chars] [chars]

Output to syslog from pipeline

-

""

IOMD-2-INITFAIL

2-Critical

IOMD initialization error: [chars] Slot [dec] Subslot [dec]

A failure occurred during initialization of IOMD. The line card that generated the message is not functional.

iomd

IOMD_AUTO_RECOVERY_ACTION

IOMD-2-POE_INIT_FAIL

2-Critical

[chars] on Slot [dec] Subslot [dec]. POE functionality will not work on this LC

A failure occurred during initialization of LC for POE. POE is not functional on the line card that generated the message.

iomd

IOMD_STD_ACTION

IOMD-2-POE_RW_FAIL

2-Critical

[chars] on Slot [dec] Subslot [dec]. POE functionality will not continue to work on this LC

A failure occurred during read/write of POE registers from HW. POE is not functional on the line card that generated the message.

iomd

IOMD_STD_ACTION

IOMD-2-POE_FW_MISMATCH

2-Critical

[chars] on Slot [dec] Subslot [dec]. POE is not functional on this line card\n To recover from issue power-cycle the linecard using the CLI: hw-module subslot <Slot>/<Subslot> oir power-cycle

The Firmware version on this Linecard is not supported by the Software. POE is not functional on this line card The linecard should be power-cycled to recover from this issue.

iomd

IOMD_POE_FW_MISMATCH_ACTION

IOMD-3-NRU_OIR_DRAIN_FAIL

3-Error

NRU OIR EPF Fifo drain failed for mac [dec] on slot [dec]

A failure occurred during NRU OIR EPF Fifo drain. NRU datapath may not functional.

iomd

IOMD_STD_ACTION

IOMD-2-PCIE_ACCESS_FAIL

2-Critical

[chars] on Slot [dec] Subslot [dec]. PCIe access failed HW faulty shutting down this slot.

A failure occurred during read/write of PCIe registers from HW. This board is not usable in current state.

iomd

IOMD_STD_ACTION

IOMD-2-M3_FAKE_SWOVER

2-Critical

Asic [dec] on slot [dec] detected a spurious switchover

ASIC on the linecard detected a fake switchover event. Check if it is a prototype board

iomd

IOMD_STD_ACTION

IOMD-2-INITFAIL

2-Critical

IOMD initialization error: [chars] Slot [dec] Subslot [dec]

A failure occurred during initialization of IOMD. The line card that generated the message is not functional.

iomd

IOMD_AUTO_RECOVERY_ACTION

IOMD-2-TIMERFAIL_CXT

2-Critical

IOMD timer context error

A failure occurred during context retrieval for a timer

iomd

IOMD_AUTO_RECOVERY_ACTION

IOMD-2-IPC_ERR

2-Critical

IOMD IPC error: [chars] Slot [dec] Subslot [dec]

A failure in communication occurred to another process

iomd

IOMD_AUTO_RECOVERY_ACTION

IOMD-3-RFROLE_FAIL

3-Error

Failed to update IM role for reason: [chars]

Failure to handle role update.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-HARFROLE_FAIL

3-Error

Failed to [chars].

Failure to establish start client or server.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-QUEUE_FAIL

3-Error

Failed to dequeue because [chars].

Failure to handle events in queue.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-TIMER_FAIL

3-Error

Failed to [chars].

Failure in timer processing.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-MARSHAL_ERR

3-Error

Failed to marshal [chars].

Failure to marshal tdl message

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-HAIPC_FAIL

3-Error

Failed to [chars] reason: [chars].

Failure in handling IOMD HA IPC.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-CREATE_TDLH_FAILURE

3-Error

Failed to create SPA [dec]/[dec] handle

Failed to create message handle for SPA communication.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-DOMAIN_TDLH_FAILURE

3-Error

[chars] rc = [dec]

Failed to bind message handle for SPA communication.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-SETUP_TDLH_FAILURE

3-Error

Failed to set the alloc/free handler for SPA [dec]/[dec] handle

Failed to set the alloc/free handler for SPA communication.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-DISPATCH_INIT_TDLH_FAILURE

3-Error

Failed to initialize dispatch path for SPA [dec]/[dec] handle

Failed to initialize dispatch path handle for SPA communication.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-INVALID_TDL_CCAPI_USAGE

3-Error

-

Incorrect usage of an internal API that should only be used on CC.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-6-TDLMSG_INCOMPATIBLE

6-Information

Failed to copy message [chars] to buffer not allowed for current domain.

Failure to marshal a message indicates an incompatibility with the intended recipient.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-CREATE_TDLMSG_FAILURE

3-Error

Failed to create [chars] message for [chars].

Failed to create/allocate necessary TDL message for SPA communication.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-INVALID_HANDLE

3-Error

Failed to get a valid IPC handle for type [dec] slot [dec] subslot [dec].

The client handle was found to be NULL for the given type/slot/subslot.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-INVALID_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid slot number is specified in one of the internal APIs.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-INVALID_SUBSLOT_NUM

3-Error

subslot= [dec] max subslot = [dec]

An invalid subslot number is specified in one of the internal APIs.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The SPA failed to allocate a buffer for communication with\n\ the Route Processor ASR1000-RP.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

IOMD-3-ISR_RC_ERROR

3-Error

ISR return code out of range. rc=[dec]

The ISR error return code is out of range.

asr900-im

LOG_STD_SH_TECH_ACTION

IOMD-3-MESSAGE_ERROR

3-Error

Bay [dec]: [chars]

An unexpected error has occurred.

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

IOMD-3-MODULE_MESSAGE

3-Error

[chars]

An error is detected by the firmware running on the module in the slot and subslot specified in the message

esg-io-infra

LOG_STD_SH_TECH_ACTION

IOMD-3-UNSUPPORTED_MODULE

3-Error

The module [chars] in slot [dec] bay [dec] is not supported on this platform

The module inserted is not supported on this platform and will not be powered on

esg-io-infra

LOG_STD_SH_TECH_ACTION

IOMD-3-UNSUPPORTED_MODULE_IN_NEBS

3-Error

The module [chars] in slot [dec] bay [dec] is not supported in NEBS mode

The module inserted is not supported in NEBS mode and will not be powered on

esg-io-infra

LOG_STD_SH_TECH_ACTION

IOMD-3-NEBS_ACCESS_PID_FAIL

3-Error

Failed to acess NGIO PID list for [chars] on slot/bay [dec]/[dec] in NEBS mode

The access to NGIO PID list failed in NEBS mode and module will not be powered on

esg-io-infra

LOG_STD_SH_TECH_ACTION

IOMD-3-UNSUPPORTED_NGSWITCH

3-Error

The next-gen switch module [chars] in slot [dec] bay [dec] needs a system reload to take effect because current system is in legacy switching mode

Legacy and next-gen switch modules have different feature set and cli behaviors which require system to determine corresponding switching mode at system boot time. Current selection algorithm is to check whether next-gen switch module locates within chassis at boot time if yes system come up in ngswitch mode otherwise in legacy mode. Users need to reload system to change system switching mode.

esg-io-infra

LOG_STD_SH_TECH_ACTION

IOMD-3-UNSUPPORTED_LEGACY_SWITCH

3-Error

The previous generation switch module [chars] in slot [dec] bay [dec] is not compatible with current next-gen switching mode

Legacy and next-gen switch modules have different feature set and cli behaviors which require system to determine corresponding switching mode at system boot time. Current mode selection is to check whether next-gen switch module locates in the chassis at boot time if yes system will come up in ngswitch mode otherwise in legacy mode. Users need to reload system to change system switching mode if it is neccessary

esg-io-infra

LOG_STD_SH_TECH_ACTION

IOMD-3-SIGBUS_ERROR

3-Error

SIGBUS received for IM in slot: [dec]

SIGBUS error encountered for IM

asr900-im

LOG_STD_SH_TECH_ACTION

UEA_UPPER_APP-3-MEM_FAILURE

3-Error

Not enought memory for [chars]

Failed to create a UEA object.

uea-im-tdm

LOG_STD_SH_TECH_ACTION

UEA_UPPER_APP-3-NULL_PTR

3-Error

-

Pointer to a UEA object is NULL.

uea-im-tdm

LOG_STD_SH_TECH_ACTION

UEA_UPPER_APP-3-WINIPC_FAILURE

3-Error

WinIPC failed : command [chars]

WinIPC Failed

uea-im-tdm

LOG_STD_SH_TECH_ACTION

UEA_UPPER_APP-3-TDM_ENCAP

3-Error

Unsupported Encap : [dec]

TDM Configuration failed

uea-im-tdm

LOG_STD_SH_TECH_ACTION

SERIAL_IM-3-CREATION_FAILURE

3-Error

Failed to create object for slot [dec]/[dec] spa_type [dec].

Failed to create an Interface Module object.

wolfeisland-sw

LOG_STD_SH_TECH_ACTION

SERIAL_IM-3-ANALYZE_FAILURE

3-Error

Failed to analyze object for slot [dec]/[dec] spa_type [dec]. [chars].

Failed to analyze an Interface Module object.

wolfeisland-sw

LOG_STD_SH_TECH_ACTION

SERIAL_IM-3-PLUGIN_START

3-Error

Plugin start failed for slot [dec]/[dec]. Action: [chars]

Pointer to a UEA object is NULL.

wolfeisland-sw

LOG_STD_SH_TECH_ACTION

SERIAL_IM-3-PLUGIN_INIT

3-Error

Plugin init failed for slot [dec]/[dec]. Action: [chars].

Plugin init failed UEA

wolfeisland-sw

LOG_STD_SH_TECH_ACTION

UEA_IOMD_SPA-3-HWIDB_FAILURE

3-Error

Creation: port [dec] vc [dec]

Failed to create a hwidb.

asr900-im

LOG_STD_SH_TECH_ACTION

UEA_IOMD_SPA-3-DEVICE_ERROR

3-Error

subSlot [dec] spatype 0x[hec]. Device error: [chars]

An error related to a device on the SPA is detected.

asr900-im

LOG_STD_SH_TECH_ACTION

UEA_IOMD_SPA-3-ISR_RC_ERROR

3-Error

ISR return code out of range. rc=[dec]

The ISR error return code is out of range.

asr900-im

LOG_STD_SH_TECH_ACTION

UEA_IOMD_SPA-3-SPA_INTF_ID_CC_ALLOC_FAILED

3-Error

Failed to allocate interface identifiers for SPA [chars]

Failed to get CC buffer and flow control identifiers for the SPA in the specified subslot Traffic cannot flow through the SPA under this failure condition. This can happen if the system runs out of available identifiers.

asr900-im

"Try to reduce the number of interfaces" "configured in the system either by physically removing the SPAs" "or by changing the system configuration"

UEA_IOMD_SPA-4-SPABUS

4-Warning

Subslot [dec] [chars] SPA BUS access failed. timeout=[dec] err=[dec] par=[dec] err_c=0x[hec] addr=0x%08x data =0x[hec]

SPABUS has reported an error.

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-4-SPABUS2

4-Warning

Subslot [dec] SPA BUS access failed. No SPA present error

SPABUS has reported an error.

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-6-OIR

6-Information

Bay [dec] [chars] changed to [chars]

SPA OIR Sequence

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-4-MAX_BANDWIDTH

4-Warning

Total SPA bandwidth exceeds line card capacity of %lu Mbps

The total bandwidth of SPAs exceeds the rated capacity of this line card.

asr900-im

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

UEA_IOMD_SPA-4-MAX_BANDWIDTH_NS

4-Warning

Total SPA bandwidth exceeds line card capacity full utilization of installed SPA interfaces is not supported

The total bandwidth of SPAs exceeds the rated capacity of this line card.

asr900-im

"Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card"

UEA_IOMD_SPA-3-POWER

3-Error

Bay [dec] 12V power is [chars]

SPA 12V power fault indicator

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-SPI4_INIT_FAILURE

3-Error

Bay [dec] initialization failure

Failed to create SPI4 subblock

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UEA_IOMD_SPA-3-MESSAGE_ERROR

3-Error

Bay [dec]: [chars]

An unexpected error has occurred.

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UEA_IOMD_SPA-3-SPI4_CONFIG_FAILURE

3-Error

Bay [dec] spi4 configuration failure error [dec]

Failed to configure SPI4 interface

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UEA_IOMD_SPA-3-SPI4_NOTSYNC

3-Error

[chars]: Can not synchronize SPI4 bus host: src [chars]in sync sink [chars]in sync spa: src [chars]in sync sink [chars]in sync.

SPI4 bus between modular services card and SPA is not synchronized. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image.

-

"Ensure that the SPA is properly seated " "in its subslot and reseat it if required."

UEA_IOMD_SPA-3-SPA_CTRL_INIT_FAILURE

3-Error

Subslot [dec] spa controller initialisation failure error [dec]

Failed to initialise SPA controller

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UEA_IOMD_SPA-3-SPA_CTRL_EFC_CONFIG_FAILURE

3-Error

Subslot spa controller EFC configuration failure error [dec]

Failed to configure SPA controller EFC

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UEA_IOMD_SPA-3-FCI_NOT_SET

3-Error

Bay [dec] - FCI type not set

An FCI type of zero was detected

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-EFC_CHAN_ERR

3-Error

EFC error - interface [chars] vc [dec] anyphy [dec] err_code [dec] : [chars]

Failed to configure efc channel/parameters

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION

UEA_IOMD_SPA-3-INVALID_ANYPHY

3-Error

Bay [dec] - Invalid anyphy number [dec] for vc [dec]

Interface has invalid anyphy mumber

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

UEA_IOMD_SPA-3-LINKREC_ERROR

3-Error

Link record error - Bay [dec] vc [dec] error code [dec]

Error processing link record structure

asr900-im

"Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt."

UEA_IOMD_SPA-3-SONET_CLOCK_FAILED

3-Error

SPA Sonet clock has failed status = 0x%08x

The SPA SONET clock has failed. SPAs that rely on the SPA SONET clock for proper operation such as POS and ATM will be affected.

asr900-im

"If the SPA Sonet clock does not recover perform an " "OIR. "LOG_STD_RECUR_ACTION

UEA_IOMD_SPA-3-SONET_CLOCK_RECOVERED

3-Error

SPA Sonet clock has recovered status = 0x%08x

SPA Sonet clock has recovered

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-3-INVALID_IF

3-Error

Attempted to access HWIDB for port [dec] on slot [dec] subSlot [dec]

The UEA attempted to access the HWIDB associated with\n\ a non-existent port.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-UEAIPCALLOCFAIL

3-Error

Failed to allocate Common IPC buffer [chars]

The Carrier Card failed to allocate a buffer for\n\ communication with the Route Processor.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-CMDNOINT

3-Error

HWIDB Null for command [dec] port [hex]

The Route Processor passed down a port number that is unknown on the\n\ carrier card.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-EFC_FC_MAP_FAIL

3-Error

Failed to update EFC flow control identifier for interface [chars] status = [dec]

The SPA driver is not able to update the datapath EFC flow control identifier for the interface specified in the message. This indicates a hardware error.

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-3-EFC_PROV_FAIL

3-Error

Failed to provision EFC for interface [chars] status = [dec]

The SPA driver is not able to provision EFC for the interface specified in the message. This indicates a hardware error.

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-3-EFC_UNPROV_FAIL

3-Error

Failed to unprovision EFC for VC [chars] status = [dec]

The SPA driver is not able to unprovision EFC for the interface specified in the message. This indicates a hardware error.

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-3-C2W_MAIN_INIT_FAIL

3-Error

Failed to initialize SPA main c2w bus for subslot [dec] status = [dec]

The SPA driver is not able to initialize SPA main c2w. This indicates a hardware error.

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-3-NETCLK_FAIL

3-Error

Failed to [chars] SPA reference clock on [chars]

The SPA driver is not able to correctly configure the SPA reference clock on the specified interface. This indicates a hardware error.

asr900-im

LOG_STD_NO_ACTION

UEA_IOMD_SPA-3-LVLTRTOOBIG

3-Error

Loveletter length exceeds max [dec] bytes

The UEA IOMD attempted to send a large message to the\n\ Route Processor UEA-RP.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-NODISPATCH

3-Error

Dispatch vector Null cmd=[dec] dintf=[dec]

No command dispatch vector was found for the specified interface.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-BADMALUCMD2

3-Error

Unsupported MALU cmd/arg0=0x%04x%04x arg1arg2=0x%04x%04x hwidb=[chars]

-

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-BADMALUCMD

3-Error

Unsupported MALU command [dec] arg=[hex] pascb=[hex]

-

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-BAD_IFCOMTYPE

3-Error

Bad ifcom message type=[dec]

-

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-IPCSENDFAIL

3-Error

Failed to send IPC message [chars]

The Linecard failed to send a message to the\n\ Route Processor UEA-RP.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-IPCALLOCFAIL

3-Error

Failed to allocate IPC buffer [chars]

The SPA failed to allocate a buffer for communication with\n\ the Route Processor UEA-RP.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-IPCPORTFAIL

3-Error

Failed to open IPC port '[chars]' [chars] with error [chars]

The RP failed to open a port for communication with a SPA\n\ module.

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-IPCPORT

3-Error

Failed to [chars] IPC port '[chars]' error [chars]

The Linecard failed to create a port for\n\ communication with the Route Processor UEA-RP.

asr900-im

"Copy the error message exactly as it appears and report it to your\n\ technical support representative."

UEA_IOMD_SPA-3-FAST_NOTIFY_ERROR

3-Error

Failed to send fast notification to [chars] for [chars] [chars].

The SPA driver failed to deliver a fast notification.

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-6-LOGGERMSGTOOBIG

6-Information

Logger message length [dec] bytes exceeds the maximum allowed size

The carrier card attempted to send a large message to the Route Processor

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-FRR_CFG_FAIL

3-Error

Failed to configure fast reroute on [chars]: [chars].

The SPA driver failed to configure fast rerouting on an interface.

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-APS_CFG_FAIL

3-Error

Failed to configure APS on [chars]: [chars].

The SPA driver failed to configure APS on an interface.

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-APS_PGP_FAIL

3-Error

APS PGP Message send failed toslot/tobay [dec]: [dec].

APS PGP between working and protect has failed

asr900-im

LOG_STD_ACTION

UEA_IOMD_SPA-3-BADSWITCHOVER

3-Error

[chars]: Invalid HA event detected: [chars]

HA switch over event comes before finishing inialization.

-

LOG_STD_SH_TECH_ACTION

UEA_IOMD_SPA-4-BADPOINTER

4-Warning

Function [chars] detected an invalid [chars] pointer of %08lX ignoring

A software error has occurred this message is displayed when \n\ an invalid pointer is detected.

-

"LOG_STD_SH_TECH_ACTION"

UEA_IOMD_SPA-3-INITFAIL

3-Error

Initialization error

A failure occurred during the initialization.

Obtain from traceback.

LOG_STD_REDUCE_ACTION

UEA_IOMD_SPA-1-AUTHENTICATION_FAIL

1-Alert

IM authentication failed for slot/bay [dec]/[dec]

This Module may not have been manufactured by Cisco or with Cisco's authorization. This product may contain software that was copied in violation of Cisco's license terms. If your use of this product is the cause of a support issue Cisco may deny operation of the product support under your warranty or under a Cisco technical support program such as Smartnet. Please contact Cisco's Technical Assistance Center for more information.

iomd-infra

LOG_STD_ACTION

UEA_IM-3-CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

Failed to create a SPA object.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-SPA_CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec].

Failed to create a SPA object.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-NULL_VFT

3-Error

[chars] virtual function table is not initialized. spaType=0x[hec]

A required function table is not initialized

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-NULL_VFUNC

3-Error

[chars] vector is not initialized. spaType=0x[hec]

A required function vector is not initialized

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-MEM_ALLOC_ERROR

3-Error

[chars]

Memory allocation error.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid slot number is specified in one of the internal APIs.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_SUBSLOT_NUM

3-Error

subslot= [dec] max subslot = [dec]

An invalid subslot number is specified in one of the internal APIs.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_RP_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid RP slot number is specified in one of the internal APIs.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_CPU_NUM

3-Error

cpu= [dec] max cpu = [dec]

An invalid CPU number is specified in one of the internal APIs.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_SLOTUNIT_NUM

3-Error

cardwide-port = [dec] max cardwide-port = [dec]

An invalid cardwide-port number is specified in one of the internal APIs.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_INDX_RANGE

3-Error

index1= [dec] index2= [dec] maxIndex= [dec]

An invalid index range is specified in one of the internal APIs.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_IF_INDEX

3-Error

index= [dec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec]

Index for the interface is not valid.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

ETHER_MODULE-3-INVALID_DATA_INSTANCE

3-Error

interface type [chars] slot [dec] port [dec] vc [dec] : [chars]

Data required to support the interface is not available.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-POWER_CYCLE

3-Error

[chars] occurred on Shared Port Adapter [dec]/[dec]

An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-DIAG_CONFIG

3-Error

[chars] did not complete [dec]/[dec]

An error has occured during diagnostic test.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

ETHER_MODULE-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-IPC_FAILURE

3-Error

IPC failure while [chars]

An error has occurred while prepareing or sending an IPC message.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-SENDCFGFAIL

3-Error

Failed to send configuration for [chars] to carrier-card for subslot=[dec]/[dec]

Sending configuration failed.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-CREATE_TDLH_FAILURE

3-Error

Failed to create SPA [dec]/[dec] handle

Failed to create message handle for SPA communication.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-DOMAIN_TDLH_FAILURE

3-Error

[chars] rc = [dec]

Failed to bind message handle for SPA communication.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-SETUP_TDLH_FAILURE

3-Error

Failed to set the alloc/free handler for SPA [dec]/[dec] handle

Failed to set the alloc/free handler for SPA communication.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-DISPATCH_INIT_TDLH_FAILURE

3-Error

Failed to initialize dispatch path for SPA [dec]/[dec] handle

Failed to initialize dispatch path handle for SPA communication.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-INVALID_SPA_TDL_CCAPI_USAGE

3-Error

-

Incorrect usage of an internal API that should only be used on CC.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-6-TDLMSG_INCOMPATIBLE

6-Information

Failed to copy message [chars] to buffer not allowed for current domain.

Failure to marshal a message indicates an incompatibility with the intended recipient.

asr1k-spa-infra

LOG_STD_SH_TECH_ACTION

UEA_IM-3-CREATE_TDLMSG_FAILURE

3-Error

Failed to create [chars] message for [chars].

Failed to create/allocate necessary TDL message for SPA communication.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

UEA_IM-3-GET_ATTR_FAILURE

3-Error

Failed to get attribute pointer

Failed to get SPA attribute information.

asr1k-io-internal

LOG_STD_SH_TECH_ACTION

LINK-6-DOWNSHIFT

6-Information

Experienced Channel Quality Impairment on interface [chars] Downshifting Speed to [chars]

Speed Downshift Detected.

firmware

"No action is required."

UEA_TDM_IM-3-UEA_CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type = [dec] PID=[chars]

Failed to create a UEA object.

uea-im-tdm

LOG_STD_SH_TECH_ACTION

UEA_TDM_IM-3-NULL_UEA_PTR

3-Error

-

Pointer to a UEA object is NULL.

uea-im-tdm

LOG_STD_SH_TECH_ACTION

UEA_TDM_IM-3-PLUGIN_INIT

3-Error

Plugin init failed. UEA object [chars] Action [chars].

Plugin init failed UEA

uea-im-tdm

LOG_STD_SH_TECH_ACTION

UEA_TDM_IM-6-EEPROM_PROG_PASSED

6-Information

EEPROM programming passed for IM

IM EEPROM was programmed successfully attempting IM reset

-

LOG_STD_NO_ACTION

UEA_TDM_IM-6-EEPROM_PROG_FAILED

6-Information

EEPROM programming FAILED for IM

IM EEPROM programming was unsuccessful allowing module to boot

-

LOG_STD_NO_ACTION

UEA_SPA-3-CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec].

Failed to create a SPA object.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-SPA_CREATION_FAILURE

3-Error

slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec].

Failed to create a SPA object.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-NULL_VFT

3-Error

[chars] virtual function table is not initialized. spaType=0x[hec]

A required function table is not initialized

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-NULL_VFUNC

3-Error

[chars] vector is not initialized. spaType=0x[hec]

A required function vector is not initialized

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-MEM_ALLOC_ERROR

3-Error

[chars]

Memory allocation error.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid slot number is specified in one of the internal APIs.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_SUBSLOT_NUM

3-Error

subslot= [dec] max subslot = [dec]

An invalid subslot number is specified in one of the internal APIs.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_RP_SLOT_NUM

3-Error

slot= [dec] max slot = [dec]

An invalid RP slot number is specified in one of the internal APIs.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_CPU_NUM

3-Error

cpu= [dec] max cpu = [dec]

An invalid CPU number is specified in one of the internal APIs.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_SLOTUNIT_NUM

3-Error

cardwide-port = [dec] max cardwide-port = [dec]

An invalid cardwide-port number is specified in one of the internal APIs.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_INDX_RANGE

3-Error

index1= [dec] index2= [dec] maxIndex= [dec]

An invalid index range is specified in one of the internal APIs.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_IF_INDEX

3-Error

index= [dec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec]

Index for the interface is not valid.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_DATA_INSTANCE

3-Error

interface type [chars] slot [dec] port [dec] vc [dec] : [chars]

Data required to support the interface is not available.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-POWER_CYCLE

3-Error

[chars] occurred on Shared Port Adapter [dec]/[dec]

An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-DIAG_CONFIG

3-Error

[chars] did not complete [dec]/[dec]

An error has occured during diagnostic test.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-IPC_FAILURE

3-Error

IPC failure while [chars]

An error has occurred while prepareing or sending an IPC message.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-SENDCFGFAIL

3-Error

Failed to send configuration for [chars] to carrier-card for subslot=[dec]/[dec]

Sending configuration failed.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-CREATE_TDLH_FAILURE

3-Error

Failed to create SPA [dec]/[dec] handle

Failed to create message handle for SPA communication.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-DOMAIN_TDLH_FAILURE

3-Error

[chars] rc = [dec]

Failed to bind message handle for SPA communication.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-SETUP_TDLH_FAILURE

3-Error

Failed to set the alloc/free handler for SPA [dec]/[dec] handle

Failed to set the alloc/free handler for SPA communication.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-DISPATCH_INIT_TDLH_FAILURE

3-Error

Failed to initialize dispatch path for SPA [dec]/[dec] handle

Failed to initialize dispatch path handle for SPA communication.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_SPA_TDL_CCAPI_USAGE

3-Error

-

Incorrect usage of an internal API that should only be used on CC.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-6-TDLMSG_INCOMPATIBLE

6-Information

Failed to copy message [chars] to buffer not allowed for current domain.

Failure to marshal a message indicates an incompatibility with the intended recipient.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-CREATE_TDLMSG_FAILURE

3-Error

Failed to create [chars] message for [chars].

Failed to create/allocate necessary TDL message for SPA communication.

-

LOG_STD_SH_TECH_ACTION

UEA_SPA-3-INVALID_HANDLE

3-Error

Failed to get a valid IPC handle for type [dec] slot [dec] subslot [dec].

The client handle was found to be NULL for the given type/slot/subslot.

-

LOG_STD_SH_TECH_ACTION

FPD_MGMT-6-BUNDLE_DOWNLOAD

6-Information

Downloading FPD image bundle for [chars] card in [chars] ...

The system is downloading the field programmable device image bundle to the system main memory.

-

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_TIME

6-Information

Estimated total FPD image upgrade time for [chars] card in [chars] = %TS.

The estimated total time for all FPD images to be upgraded is displayed for the indicated card.

-

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_START

6-Information

[chars] FPD ID=[dec] image upgrade in progress for [chars] card in [chars].

The FPD image upgrade process has started. Do not interrupt the upgrade operation as any interruption could render the target card unusable. Avoid actions like removing the target card from the system powering off the system or using commands that can power-cycle the target card during the upgrade process.

-

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_PASSED

6-Information

[chars] FPD ID=[dec] image in the [chars] card in [chars] has been successfully

The FPD image upgrade process has completed successfully for the indicated device.

-

LOG_STD_NO_ACTION

FPD_MGMT-6-OVERALL_UPGRADE

6-Information

All the attempts to upgrade the required FPD images have been completed for [chars] card in [chars]. Number of successful/failure upgrades:

All the FPD image upgrades have completed for the indicated card.

-

LOG_STD_NO_ACTION

FPD_MGMT-6-UPGRADE_RETRY

6-Information

Attempting to recover from the failed upgrades ...

Because of an image upgrade failure the system will attempt again the upgrade operation for the same FPD image.

-

LOG_STD_NO_ACTION

FPD_MGMT-6-PENDING_UPGRADE

6-Information

[dec] more FPD image upgrade operation will be required on [chars] in [chars] after additional power-cycle operation on the target card.

All upgrade operations have not completed and additional power-cycle operations are required before the upgraded or new FPD image will be applied to the system configuration. The message text indicates the number of pending upgrade operations that will be performed. More than one power-cycle operation might be required to complete the overall upgrade process.

-

LOG_STD_NO_ACTION

FPD_MGMT-5-UPGRADE_ATTEMPT

5-Notice

Attempting to automatically upgrade the FPD images for [chars] card

The automatic FPD image upgrade feature is enabled with the <CmdBold> upgrade fpd auto<NoCmdBold> global configuration command. The system is currently upgrading an incompatible image version automatically.

-

"No action is required. The upgrade process can take a long time.The " "FPD_MGMT-6-UPGRADE_TIME message gives an estimate of the total " "upgrade time"

FPD_MGMT-5-CARD_POWER_CYCLE

5-Notice

[chars] card in [chars] is being power cycled for the FPD image upgrade to take effect.

The indicated card is being power cycled after the FPD image upgrade. This action allows the target card to be operational with the new upgraded FPD image or images.

-

LOG_STD_NO_ACTION

FPD_MGMT-5-POST_UPGRADE_REMINDER

5-Notice

[chars] card in [chars] will require a [chars] for the FPD image upgrade to take effect.

The indicated card will require manual intervention after the FPD image upgrade. The specified operation is required for the upgraded FPD image to take effect.

-

LOG_STD_NO_ACTION

FPD_MGMT-4-BYPASS_AUTO_UPGRADE

4-Warning

The automatic FPD image upgrade feature is not enabled bypassing the image upgrade for [chars] card in [chars].

The automatic FPD image upgrade feature is not enabled. The incompatible image will not be automatically upgraded. The card will be disabled until the image is upgraded to a compatible version.

-

"Enable the automatic FPD image upgrade with the <CmdBold>upgrade fpd " "auto<NoCmdBold> global configuration command or use the <CmdBold>upgrade " "hw-module<NoCmdBold> privileged EXEC command for a manual upgrade " "operation. For more information about these commands refer to the " FPD_DOCUMENT_NAME "."

FPD_MGMT-4-UPGRADE_EXIT

4-Warning

Unexpected exit of FPD image upgrade operation for [chars] card in [chars].

The FPD image upgrade operation was interrupted by the physical removal of the card from the system or by the use of other commands that have interrupted the normal operation of the target card. The partial upgrade operation might have left the card unusable because of corrupted FPD images.

-

"If the card does not come up after reinserting into the system then " "perform the recovery upgrade operation by using the <CmdBold>upgrade " "hw-module<NoCmdBold> privileged EXEC command. With this command the " "system will attempt the reprogramming of the image to recover from the " "previous partial upgrade operation. For more information about " "performing a recovery upgrade operation refer to the " FPD_DOCUMENT_NAME "."

FPD_MGMT-4-VERSION_CHECK_ABORTED

4-Warning

FPD image version check operation has been aborted for [chars] card in [chars] because manual upgrade has already being started.

The FPD image version check operation required for the automatic upgrade feature is not being performed for the indicated card because the <CmdBold>upgrade hw-module<NoCmdBold> privileged EXEC command has already being executed. These two operations cannot be performed at the same time.

-

"If an automatic upgrade operation is required do not enter the " "<CmdBold>upgrade hw-module<NoCmdBold> privileged EXEC command for the " "manual upgrade while the target card is initializing. Enter the " "<CmdBold>show hw-module subslot fpd<NoCmdBold> command and ensure that " "the target card is displayed in the command output before proceeding " "with the manual upgrade."

FPD_MGMT-4-CFG_NOT_SYNCED

4-Warning

Failed to sync \[chars]\ command to standby: [chars]

A FPD configuration command failed to get synced to standby RP due to the indicated error condition. Usually this can happen if the standby RP hardware doesn't support the type of filesystem supported on the active one.

-

"Configure again the command with a filesystem that is supported on " "both standby and active RP. To find out if a specific filesystem is " "also supported on standby RP the <CmdBold>dir ?<NoCmdBold> command " "can be used to display a list of filesytem supported on both standby " "and active RP."

FPD_MGMT-3-INVALID_IMG_VER

3-Error

Invalid [chars] FPD ID=[dec] image version detected for [chars] card in [chars].

The indicated field programmable device contains an invalid version for the FPD image because the system was not able to extract this information from the indicated card. A failed upgrade attempt might have corrupted the FPD image identification on the device.

-

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-IMG_VER_NOT_FOUND

3-Error

FPD image version information is not available for [chars] card in [chars]. All the FPD images will be upgraded to recover from this error.

The FPD image version information for the indicated card is not available because the system was not able to extract this information for all the FPDs in the card. This could be the result of a corrupted FPD image from a power failure.

-

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-INCOMP_IMG_VER

3-Error

Incompatible [chars] FPD ID=[dec] image version detected for [chars] card

An incompatible FPD image version has been detected. The FPD image needs to be upgraded either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled.

-

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-MAJOR_VER_MISMATCH

3-Error

Major image version mismatch detected with [chars] FPD ID=[dec] for [chars] card

A major image version mismatch has been detected. This incompatibility will need to be resolved by doing an upgrade or downgrade operation either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled.

-

FPD_VERSION_ERROR_STD_ACTION

FPD_MGMT-3-OPEN_FAILED

3-Error

Failed to open [chars] [chars]. Please make sure that the required file

The system cannot access the required file from the indicated URL.

-

"Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed."

FPD_MGMT-3-OUT_OF_MEMORY

3-Error

Could not allocate the required [dec] bytes of memory.

The system does not have enough free main memory to download the bundle file.

-

FPD_NO_FREE_MEMORY_STD_ACTION

FPD_MGMT-3-READ_ERROR

3-Error

Could not read the [chars] file.

The system cannot read the required file from the indicated URL.

-

"Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed."

FPD_MGMT-3-BNDL_WRONG_MAGIC_NUM

3-Error

The [chars] file contains a wrong magic number for the image bundle: [hex] expected [hex]. Please make sure that this is a valid FPD image [chars]

The indicated file might not be a valid FPD image bundle or package file for the target card or the file could be corrupted.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_WRONG_HDR_LEN

3-Error

The [chars] file contains wrong header length for the image bundle: [dec] bytes expected [dec] bytes. Please make sure that this is a valid

The indicated file might not be a valid FPD image bundle or package file for the target card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_WRONG_SIZE

3-Error

The [chars] file contains incorrect image bundle size: [dec] bytes expected [dec] bytes. Please make sure that this is a valid FPD image [chars] file

The indicated file might not be a valid FPD image bundle or package file for the target card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_CRC_CHECK_FAIL

3-Error

The [chars] file contains a corrupted image bundle - CRC mismatch: current value [hex] expected value [hex]. Please make sure that this is a valid FPD image [chars] file for card in [chars].

The file failed the CRC checking process. This failure indicates a corrupt FPD image bundle or package file.

-

"Try to download again the required package from the Cisco " "Software Center website as the indicated one might be corrupted. " "If the problem persists copy the error message exactly as it appears " "and gather the output of the <CmdBold>show hw-module subslot fpd" "<NoCmdBold> <CmdBold>show upgrade fpd table<NoCmdBold> and <CmdBold>" "show upgrade fpd file<NoCmdBold> <CmdArg>fpd-pkg-url<NoCmdArg> commands " "then contact your technical support representative with the gathered " "information."

FPD_MGMT-3-BNDL_CARD_TYPE_MISMATCH

3-Error

The [chars] file does not contain the card type [hex] in the image bundle

The image bundle in the indicated file does not contain a correct card type value for the target card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BNDL_NAME_PREFIX_MISMATCH

3-Error

The [chars] file contains a bundle name prefix [chars] that does not match

The content of the selected FPD image bundle does not match its filename.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INCOMP_BNDL_VER

3-Error

The selected [chars] file contain an image bundle that has a version number that is incompatible for this IOS release - [chars]. Selected version = [dec].[dec] minimum compatible version = [dec].[dec]. Please make sure that this is a valid FPD image [chars] file for card in [chars].

The version of the selected FPD image bundle does not contain a valid version number that is compatible for the IOS release. The major version number should be the same and the minor version number should be at least equal to the minimal required version.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-MISSING_IMAGE

3-Error

Could not find the required [chars] image FPD ID=[dec] and FPD version=[dec].[dec] compatible with HW version=[dec].[dec] from the [chars]-fpd.bndl bundle in [chars]

The indicated FPD image bundle or package file might not be the correct one. IF this is a FPD image package file then an incompatible package file might have been renamed with a filename that matched with the one that the system is expecting for this Cisco IOS software release. You should never rename an FPD image package file name.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_MAJOR_VER

3-Error

The selected FPD image for upgrade contains wrong FPD image major version number = '[dec]' expected number = '[dec]' for [chars] FPD ID [dec].

The file used for upgrade might not be a valid FPD image bundle or package file for the card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_MAGIC_NUM

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong magic

The indicated file might not be a valid FPD image bundle or package file for the card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_HDR_LEN

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong header

The indicated file might not be a valid FPD image bundle or package file for the card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-WRONG_IMG_DATA_LEN

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong data

The indicated file might not be a valid FPD image bundle or package file for the card.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-IMG_CRC_CHECK_FAILED

3-Error

The FPD image for [chars] FPD ID [dec] in [chars] file is corrupted - CRC

The image failed the CRC checking process this indicates a corrupt FPD image bundle or package file.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-FPD_UPGRADE_FAILED

3-Error

[chars] FPD ID=[dec] image upgrade for [chars] card in [chars] has FAILED.

The FPD image upgrade process has failed for the indicated device.

-

"Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "<CmdBold>show hw-module subslot fpd<NoCmdBold> and contact your " "technical support representative with the gathered information."

FPD_MGMT-3-FPD_UPGRADE_CANCELED

3-Error

Rest of the FPD upgrade sequence for [chars] card in [chars] has been canceled due to upgrade failure with [chars] FPD ID=[dec] image.

The FPD image upgrade process for additional FPD images has been canceled due to upgrade error in the indicated device.

-

"Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "<CmdBold>show hw-module subslot fpd<NoCmdBold> and contact your " "technical support representative with the gathered information."

FPD_MGMT-3-SEND_IMG_FAILED

3-Error

[chars] FPD ID=[dec] image for [chars] card in [chars] has failed to be sent

The FPD image was not able to be sent for the upgrade operation. The system might be too busy to handle this operation. The affected card will be disabled by this failure.

-

"Wait until the system load is lower to try again with the manual upgrade " "procedure by using the <CmdBold>upgrade hw-module<NoCmdBold> privileged " "EXEC command. If the symptom persists copy the error message " "exactly as it appears and gather the output of the <CmdBold>show " "tech-support<NoCmdBold> command and contact your technical support " "representative with the gathered information."

FPD_MGMT-3-IMG_DATA_UNCOMPRESS_ERROR

3-Error

Could not uncompress [chars] FPD image for [chars] in [chars].

An error has been detected during the uncompress operation of the compressed FPD image data.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-BUNDLE_EXTRACT_ERROR

3-Error

Cannot extract the [chars] bundle from [chars] - [chars]

Bundle file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-PKG_VER_FILE_EXTRACT_ERROR

3-Error

Cannot extract the [chars] version file from [chars] - [chars]

Package version file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INVALID_PKG_FILE

3-Error

The indicated file [chars] is not a valid FPD image package file - [chars]

The file format does not appear to be a valid FPD image package.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INVALID_PKG_FILE_SIZE

3-Error

The indicated file [chars] does not have a valid FPD image package

The file size of the indicated FPD image package does not meet the required minimum size. The file is too small to be a valid FPD image package file.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-READ_BNDL_HDR_ERROR

3-Error

Failed to read the FPD bundle header from [chars] file.

The indicated file might not be a valid FPD image bundle or package file.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-INVALID_IMAGE_SIZE

3-Error

The [chars] FPD image from [chars] file does not have a valid image size: expected size = [dec] bytes actual size = [dec] bytes.

The size of the indicated FPD image does not have the expected size. The FPD image bundle or package might not be a valid file.

-

FPD_WRONG_PKG_STD_ACTION

FPD_MGMT-3-MISSING_DEV_INFO

3-Error

Could not find [chars] FPD ID=[dec] in the list of FPD IDs populated

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-MISSING_BUNDLE_ENTRY

3-Error

Failed to find a matching entry in the programmable device bundle information table for [chars] in [chars]. Card type or HW version [dec].[dec]

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-CLOSE_FAILED

3-Error

Failed to close [chars] file.

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-UNKNOWN_BNDL_HDR_FORMAT

3-Error

Unknown header format version: [hex]

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-INVALID_UPGRADE_RESULT

3-Error

Invalid upgrade result '[dec]' received for the FPD image upgrade of [chars] FPD ID=[dec] for [chars] card in [chars].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-TOO_MANY_FPD_ENTRIES

3-Error

Too many FPD entries for the FPD Bundle Info Table. Required number of entries = [dec] maximum number of entries allowed = [dec].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-DUPLICATE_UPGRADE_RESULT

3-Error

Upgrade result already received for the FPD image upgrade of FPD ID [dec] for [chars] card in [chars].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-UPGRADE_LIST_FULL

3-Error

Could not add a new entry in the FPD Management Upgrade List. No upgrade will be performed for the [chars] card in [chars].

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-SW_ERROR

3-Error

NULL

FPD_INTERNAL_SW_ERR_STD_EXPLANATION

-

LOG_STD_ACTION

FPD_MGMT-3-IPC_FAILED

3-Error

Failed to send IPC message to [chars] in [chars] - [chars]

The system failed to send a message via IPC to the indicated card. The cause of the specific IPC failure is inicated in the message.

-

LOG_STD_ACTION

FPD_MGMT-3-PKG_FILE_SEARCH_FAILED

3-Error

FPD image package [chars] cannot be found in system's flash card or

By default if the <CmdBold>upgrade fpd path<NoCmdBold> <CmdArg>fpd-pkg-url<NoCmdArg> global configuration command is not configured then the system will try to locate the required FPD image package file from removable flash cards or disks that are accessible by the system for FPD upgrade. This message indicates that the system could not find the package file.

-

"Make sure that the indicated FPD image package file is copied into a " "flash card or disk that is accessible by the system then restart the " "FPD upgrade by reinsertion of the target card to the system or use of " "a system command to reload or power-cycle the target card."

FPD_MGMT-3-CARD_DISABLED

3-Error

[chars] card in [chars] is being disabled because of an incompatible FPD image version. Note that the [chars] package will be required if you want to perform the upgrade operation.

The indicated card contains an incompatible FPD image version and is being disabled to avoid operational problems with the existing Cisco IOS software. This can happen if the automatic upgrade feature has not been enabled with the <CmdBold>upgrade fpd auto<NoCmdBold> global configuration command or if the automatic upgrade operation failed to perform the required upgrade or because it could not find the necessary FPD image package file. The incompatible image will need to be upgraded in order for the system to enable the card.

-

"The FPD image upgrade can be performed automatically by making sure that " "the automatic upgrade feature is enabled with the <CmdBold>upgrade fpd " "auto<NoCmdBold> global configuration command and the necessary FPD image " "package file is located in the system's default filesystem e.g. disk0: "

FPD_MGMT-3-PKG_VER_MISMATCH_NOTE

3-Error

The FPD image package being used [chars] is not the right version for

The indicated FPD image package that is being used in FPD automatic upgrade does not contain the correct version information for the IOS version that is running in the system. This condition can occur if a different version of the FPD image package was renamed to match the filename that the IOS image is expecting to use. The upgrade operation will still be performed by trying to find the required FPD image from the renamed package file.

-

"If the upgrade operation fails because the required FPD image cannot be " "found with the renamed FPD image package replace the wrong package " "file with a valid one and perform the upgrade operation again."

FPD_MGMT-3-INVALID_IMG_FORMAT

3-Error

Invalid image format '[chars]' detected for FPD ID=[dec].

The selected FPD image to upgrade the indicated field programmable device does not have the right image format that can be used by the system to perform the upgrade operation.

-

"Please check if the FPD image package used in the upgrade is for the " "correct platform. This can be checked by using the <CmdBold>show upgrade " "fpd package default<NoCmdBold> privileged EXEC command."

FPD_MGMT-2-CREATE_FAIL

2-Critical

Couldn't create [chars].

The system does not have enough free main memory to create the specified resource.

-

FPD_NO_FREE_MEMORY_STD_ACTION

TRANSCEIVER-6-REMOVED

6-Information

Transceiver module removed from [chars]

The online insertion and removal OIR facility detected the

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-6-INSERTED

6-Information

transceiver module inserted in [chars]

The online insertion and removal OIR facility detected a

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-6-REMOVED_QSA_SFP

6-Information

Transceiver module removed from QSA [chars]

The online insertion and removal OIR facility detected the

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-6-UNSUPPORTED_MODE

6-Information

Transceiver module [chars] going in err-disabled state

The online insertion and removal OIR facility detected the

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-6-INSERTED_QSA_SFP

6-Information

transceiver module inserted in QSA [chars]

The online insertion and removal OIR facility detected a

spa-infra

LOG_STD_NO_ACTION

TRANSCEIVER-3-CHECKSUM_ERROR

3-Error

Detected in the transceiver module in [chars] module disabled

A checksum error was detected when reading the ID PROM of a transceiver module for the interface specified in the error message. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. If the problem persists LOG_STD_ACTION."

TRANSCEIVER-3-INIT_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

An initialization failure occurred for the transceiver module for the interface specified in the error message. This condition could be caused by software firmware or hardware problem. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-NOT_COMPATIBLE

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is not compatible with the interface. As a result of the error the module is disabled.

spa-infra

"Replace the module with a compatible transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_IDENTIFIED

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message could not be identified and may not be compatible with the interface. As a result of the error the module is disabled.

spa-infra

"Replace the module with a compatible transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_SUPPORTED

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is not a cisco supported module. As a result of the error the module is disabled.

spa-infra

"Replace the module with a cisco supported transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-NOT_ALLOWED_ONLINE

3-Error

Detected for transceiver module in [chars] module disabled

The transceiver module for the interface specified in the error message is a restricted transceiver type and is not allowed online in the current configuration for that module. As a result of the error the module is disabled.

spa-infra

"Replace the module with a supported transceiver or modify the " "configuration to allow the current transceiver. If the problem " "persists LOG_STD_ACTION."

TRANSCEIVER-3-ATTACH_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

A software device driver attach failed. This condition could be caused by software firmware or hardware problem but a software or firmware problem is more likely. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-SM_CREATION_FAILURE

3-Error

Transceiver OIR State Machine creation failed for [chars] module disabled.

A state machine could not be created for the transceiver OIR operation. If a %SYS-2-MALLOCFAIL message was also received with this message this condition indicates insufficient system memory. Other possible causes include invalid subblock pointer.

spa-infra

"If it is insufficient system memory " LOG_STD_REDUCE_ACTION "If this message recurs " LOG_STD_ACTION

TRANSCEIVER-3-OPER_ENABLE_FAILURE

3-Error

Detected for transceiver module in [chars] module disabled

Failed to enable the transceiver module for the interface specified in the error message. This condition could be caused by software firmware or hardware problem. As a result of the error the module is disabled.

spa-infra

"Try reseating the module. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco technical support representative. "

TRANSCEIVER-3-RPC_PROCESSING_ERROR

3-Error

Transceiver RPC error: [chars]

Non Fatal error occured in processing an RPC messsage.

spa-infra

show version

TRANSCEIVER-3-RPC_INIT_FAIL

3-Error

Transceiver RPC init failure

The system failed to create the resources required to process user\n\ interface commands for transceivers. The error is not fatal but some \n\ \show\ commands could fail.

spa-infra

show version

TRANSCEIVER-3-RPC_FAILED

3-Error

Application error rc = [dec]:

The system failed to retrieve the information required to execute\n\ the comand

-

show version

TRANSCEIVER-3-UNSUPPORTED_XCVR

3-Error

Transceiver type GLC-GE-100FX is not supported on SPA-8xGE-V2

Transceiver type GLC-GE-100FX is not supported on SPA-8xGE-V2

-

"Consult the documentation and ensure supported " "transceivers are plugged into the SPA"

TRANSCEIVER-3-DRLX_100M_UP

3-Error

[chars] Dual rate transceiver may have come up wrongly with 100M speed

Dual rate transceiver which supports both 1G/100M may have wrongly detected 100M as the operational speed

-

"Please try \"shut\" and \"no shut\" on the interface once"

TRANSCEIVER-3-UNSUPPORTED_XCVR_TYPE

3-Error

Transceiver type [chars] is not supported on [chars]

The transceiver module for the interface specified in the error message is not compatible with the interface.

spa-infra

"Consult the documentation and ensure supported " "transceivers are plugged into the SPA"

SPA_EEPROM-4-DATA_TRUNCATED

4-Warning

[chars]: Data will be truncated for field type 0x[hec] - size [dec] bytes too

The provided data to be written into the indicated field type of SPA EEPROM is too big and the data will be truncated in order to fit into the allowed space.

spa-infra

"Retry the operation again with a data size that will fit into the " "indicated size for the field type."

SPA_EEPROM-4-CANNOT_UPDATE

4-Warning

[chars]: EEPROM data cannot be updated at this moment because the SPA is not in service.

The EEPROM update operation cannot be performed because the indicated SPA could have been in \out of service\ state \admin down\ state or is trying to get initialized.

spa-infra

"Retry the operation when the SPA is in service. The operational status " "of the SPA can be checked with the <CmdBold>show hw-module subslot" "<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg> <CmdBold>oir<NoCmdBold> " "command. If the SPA is shown in \"out of service\" state correct the " "indicated problem before the retry to update EEPROM. If the state shown " "is in \"admin down\" re-enable the SPA with <CmdBold>no hw-module " "subslot<NoCmdBold> <CmdArg>slot/subslot<NoCmdArg> <CmdBold>shutdown" "<NoCmdBold> command."

SPA_EEPROM-3-RPC_FAILED

3-Error

Failed to send RPC message to [chars] EEPROM of [chars] in [chars] - [chars]

System failed to send a RPC message to read/write the EEPROM of the indicated SPA. The cause of the error condition is shown in the error message.

-

SPA_EEPROM_STD_RESOURCE_ACTION

SPA_EEPROM-3-READ_FAILED

3-Error

Failed to read the EEPROM content of [chars] in [chars] offset=0x[hec] num_byte=[dec]

System failed to read the EEPROM content of the indicated SPA with the specified offset value and number of bytes to read.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-WRITE_FAILED

3-Error

Failed to write the EEPROM content for [chars] in [chars] offset=0x[hec] num_byte=[dec]

System failed to write data into the EEPROM of the indicated SPA with the specified offset value and number of bytes to write.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-SET_WR_PROTECT_FAILED

3-Error

[chars]: Failed to [chars] the EEPROM write protect mode on [chars].

System failed to enable/disable the write protect mode for SPA EEPROM on the indicated device. This might happen if the device were busy performing other tasks.

-

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-FIELD_NOT_FOUND

3-Error

[chars]: Failed to find content of field type 0x[hec] with data size = [dec] bytes. The EEPROM might require an update.

System failed to find the content of the indicated field type from the SPA EEPROM. The format of the EEPROM of the indicated SPA might not be up to date.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-FORMAT_ERROR

3-Error

[chars]: [chars]. The EEPROM might require an update.

A format error has been detected in the EEPROM of the indicated SPA. The type of error is indicated in the error message.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA_EEPROM-3-SW_ERROR

3-Error

NULL

-

spa-infra

LOG_STD_ACTION

SPA_OIR-3-MESSAGE_ERROR

3-Error

[chars]: SPA OIR event message error - [chars][dec]

An error was detected in a SPA OIR event message for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-UNEXPECTED_EVENT

3-Error

[chars]: SPA OIR unexpected event[dec]

An unexpected SPA OIR event was detected for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-EVENT_DATA_ERROR

3-Error

SPA OIR event data error - [chars][dec]

Invalid data was detected within a SPA OIR event. The SPA OIR state machines may not reflect the state of the hardware. The problem only affects one SPA but the SPA cannot be determined from the context where the error was detected. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR messages are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

spa-infra

"Check the system log for other messages that may help determine " "which SPA is affected. " SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-POST_EVENT_ERROR

3-Error

[chars]: event [dec]

A SPA OIR event message was not enqueued for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware for this SPA. This condition is most likely due to a software problem.

spa-infra

SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-UNEXPECTED_RECOVERY_ACTION

3-Error

[chars]: SPA [chars] unexpected recovery action[dec] for fail code 0x[hec]

An error occured while processing a failure message for the SPA in the slot or subslot number specified in the error message. The recovery action to be taken after a SPA failure is determined by calling a SPA driver function. This message indicates that the SPA driver function returned an invalid recovery action. After this message was issued the SPA was reloaded in an attempt to recover. The SPA driver most likely returned an invalid recovery action because of a software problem.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-EVENT_HANDLING

3-Error

[chars]: [chars]0x[hec]

A data structure error was detected when handling a SPA OIR event for the SPA in the slot or subslot specified in the error message. The SPA OIR state machines may not reflect the state of the hardware. This condition is most likely due to a software problem.

spa-infra

SPA_OIR_STD_ACTION

SPA_OIR-3-CMD_ATTR

3-Error

[chars]: Unexpected command identifier [dec]

An unexpected command identifier was detected when processing command related to a SPA OIR. The command was not processed. This is most likely due to a software problem.

spa-infra

SPA_OIR_STD_ACTION

SPA_OIR-2-INITFAIL

2-Critical

SPA OIR initialization error

A failure occurred during the SPA OIR subsystem startup. SPA OIR is not functional for the RP or line card that generated the message.

-

LOG_STD_REDUCE_ACTION

SPA_OIR-2-SUBSLOTINITFAIL

2-Critical

SPA OIR initialization error for [chars]

A failure occurred during the SPA OIR subsystem startup. SPA OIR is not functional for the slot or subslot specified in the error message

-

LOG_STD_REDUCE_ACTION

SPA_OIR-3-EVENT_TIMEOUT

3-Error

[chars]: Timeout waiting for SPA OIR event

A timeout occurred for the subslot specified in the error message while waiting for a SPA OIR event. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by software or hardware problem but a software problem is more likely. For distributed platforms SPA OIR event are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-SW_INIT_TIMEOUT

3-Error

[chars]: SPA initialization not completed

A timeout occurred for the subslot specified in the error message while waiting for SPA software driver to initialize the SPA. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by software firmware or hardware problem but a software or firmware problem is more likely.

-

"Check for other messages reported for futher insight. " "Hardware replacement should not occur first occurrence. " "Before requesting hardware replacement review troubleshooting logs " "with a Cisco techinical support representative. " SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-HW_INIT_TIMEOUT

3-Error

[chars]

A timeout occurred for the subslot specified in the error message while waiting for SPA hardware to initialize. The SPA did not complete initialization. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by a software firmware or hardware problem but a firmware or hardware problem is more likely.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-OUT_OF_SYNC

3-Error

[chars]: failure code 0x[hec]

The software SPA OIR state did not match the hardware state for the subslot in the error message. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition is expected if a SPA is reloading when an RP switchover occurs. Otherwise this condition could be caused by a software firmware or hardware problem but a firmware or software problem is more likely. This condition could also be caused by a rare interaction between SPA and its SIP.

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-HW_SIGNAL_DEASSERTED

3-Error

[chars]

The SPA was not brought up because the SPA bay is in an admin down state. The SPA bay will appear as <CmdBold>hw-module<NoCmdBold> <target spa> <CmdBold>shutdown<NoCmdBold> in the running configuration.

-

"Use the <CmdBold>no hw-module<NoCmdBold> <target spa> " "<CmdBold>shutdown<NoCmdBold> command to administratively enable " "the SPA bay."

SPA_OIR-6-PRECONFIG_MISMATCH

6-Information

[chars]: Inserted SPA type does not match preconfigured SPA type. Configuration updated

This message reports a mismatch between the inserted SPA type and the preconfigured SPA type on platforms that support pre-configuration. The inserted SPA replaces the preconfigured SPA.

-

"Check the configuration with the <CmdBold>show run<NoCmdBold> command. " "If you would like to revert to the preconfigured type remove the SPA " "and then update the configuration from a backup"

SPA_OIR-3-SPA_POWERED_OFF

3-Error

[chars]: SPA [chars] powered off after [dec] failures within [dec] seconds

The SPA was powered off because it failed too often. This condition may be caused by a software firmware or hardware error.

-

"Look for other error messages related to this SPA subslot to " "determine root cause of the failure. " SPA_OIR_EVENT_RECOVERY_ACTION

SPA_OIR-3-CORRUPT_EVENT

3-Error

[chars]

Corruption was detected within a SPA OIR event for the subslot specified in the error message. When this error occurs the system attempts automatic recovery by reloading the SPA. This condition could be caused by a software firmware or hardware problem but a firmware or software problem is more likely. For distributed platforms SPA OIR events are transported over different media depending on the platform for example c12000 uses the MBUS. An unlikely cause of this error is that an event message

-

SPA_OIR_AUTO_RECOVERY_ACTION

SPA_OIR-3-UNRECOGNIZED

3-Error

The SPA of type 0x%X in [chars] is not recognized

The type of the SPA in the specified subslot is not recognized by the operating system. The operating system might not support this SPA type on this platform or the SPA type identification stored on the SPA is invalid.

-

"Ensure that the system is running a version of the operating " "system that supports the SPA type specified in the error " "message on this platform. If the correct operating system " "version is in use copy the error message exactly as it " "appears on the console or in the system log contact your " "Cisco technical support representative and provide the " "representative with the gathered information. Include the " "information about the SPA type found on the front of the " "SPA."

SPA_OIR-3-UNSUPPORTED

3-Error

The [chars] in [chars] is not supported by the [chars] module

The SPA in the subslot specified in the error message is not supported in the specified SIP by the version of the operating system currently running on the system. The SPA type may be supported by another SIP or by a later operating system release.

-

"Ensure that the SIP specified in the error " "message supports the specified SPA type. Ensure that the " "operating system release supports the SPA type in the SIP. " "It may be necessary to upgrade your system to " "the latest operating system release in your release train or " "it may be necessary to use a different SIP type. If " "the SPA type specified in the error message does not match the " "interface types or numbers shown on the front of the SPA copy " "the error message exactly as it appears on the console or in " "the system log contact your Cisco technical support " "representative and provide the representative with the " "gathered information. Include information regarding the SPA " "type found on the front of the SPA."

SPA_OIR-3-RECOVERY_RELOAD

3-Error

[chars]: Attempting recovery by reloading SPA

The OIR facility attempted automatic recovery by reloading the SPA in the subslot specified in the error message. Look for other error messages related to this SPA subslot to determine the failure that triggered the automatic recovery.

-

LOG_STD_NO_ACTION

SPA_OIR-6-REMCARD

6-Information

Card removed from [chars] interfaces disabled

The OIR facility detected the removal of a SPA from the slot or subslot number specified in the error message. The interfaces on that SPA will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces.

-

LOG_STD_NO_ACTION

SPA_OIR-6-INSCARD

6-Information

Card inserted in [chars]

The OIR facility detected a newly inserted SPA. The interfaces associated with that SPA are operational but will be shut down until they are configured by the user. If any interfaces of that type were previously configured they will be restored to their previous state.

-

LOG_STD_NO_ACTION

SPA_OIR-6-ONLINECARD

6-Information

SPA [chars] online in [chars]

The OIR facility detected the state change to online for the SPA in the slot or subslot number specified in the message.

-

LOG_STD_NO_ACTION

SPA_OIR-6-OFFLINECARD

6-Information

SPA [chars] offline in [chars]

The OIR facility detected the state change to offline for the SPA in the slot or subslot number specified in the message.

-

LOG_STD_NO_ACTION

SPA-3-BAD_FCITYPE

3-Error

[chars]: Illegal FCI type [dec].

An invalid FCI type is passed to SPA. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SPA-3-INITFAIL

3-Error

Initialization error

A failure occurred during the initialization.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-ENTITY_INITFAIL

3-Error

SPA entity initialization error

A failure occurred during the SPA entity management subsystem startup. Entity management is not enabled.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-SW_ERROR

3-Error

NULL

-

spa-infra

LOG_STD_ACTION

SPA-3-ENVMON_INITFAIL

3-Error

SPA environmental monitoring initialization error

A failure occurred during the SPA environmental monitoring subsystem startup. Environmental monitoring is not enabled.

spa-infra

LOG_STD_REDUCE_ACTION

SPA-3-ENVMON_NOT_MONITORED

3-Error

Environmental monitoring is not enabled for [chars]

The indicated SPA has not registered any sensors with the environmental monitoring system.

-

LOG_STD_SH_TECH_ACTION

SPA-4-TEMP_WARNING

4-Warning

[chars] slot/bay [dec]/[dec] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-2-TEMP_CRITICAL

2-Critical

[chars] slot/bay [dec]/[dec] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP Please correct immediately.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-0-TEMP_SHUTDOWN_OVR

0-Emergency

[chars] slot/bay [dec]/[dec] temperature too high on sensor [dec] [dec]C

MSG_SPA_TEMP_HIGH_EXP SPA shutdown has been overridden by configuration

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-3-TEMP_SHUTDOWN

3-Error

[chars] slot/bay [dec]/[dec] temperature too high on sensor [dec] [dec]C.

MSG_SPA_TEMP_HIGH_EXP The SPA has been shut down.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-4-TEMP_SHUTDOWN_NONFATAL

4-Warning

[chars] temperature too high on sensor [dec] [dec]C. SPA has been shut down.

MSG_SPA_TEMP_HIGH_EXP The SPA has been shut down.

-

MSG_SPA_TEMP_HIGH_ACTION

SPA-4-TEMP_WARNLOW

4-Warning

[chars] temperature too low on sensor [dec] [dec]C.

SPA temperature too low. Component reliability and data integrity may be compromised.

-

"Raise the ambient temperature if it is too low. If there is no " "issue with the ambient temperature then the SPA temperature sensor has " "likely failed. If there are no data errors this warning can be " "ignored."

SPA-4-POWER_WARNING

4-Warning

[chars] power consumption [dec] Watts is higher than typical max value of [dec] Watts.

SPA power consumption is higher than the typical max value. Component reliability and data integrity may be compromised.

-

"Check for the total power available for the system. If " "there is sufficient power availabe this condition may not have " "any adverse affects."

SPA-2-VOLT_CRITICAL

2-Critical

[chars] voltage outside of nominal range. Nominal [dec]mV value[dec]mV

MSG_SPA_VOLT_EXP_COMMON

-

MSG_SPA_VOLT_ACTION_SCHED_REPLACE

SPA-2-VOLT_SHUTDOWN_OVR

2-Critical

[chars] voltage outside of operating range. Nominal [dec]mV value[dec]mV.

MSG_SPA_VOLT_EXP_COMMON

-

MSG_SPA_VOLT_SCHED_REPLACE

SPA-0-VOLT_SHUTDOWN

0-Emergency

[chars] voltage out of operating range. Nominal [dec]mV value [dec]mV.

MSG_SPA_VOLT_EXP_COMMON The SPA has been shut down to prevent component damage.

-

"Replace the SPA immediately. " "Record the associated messages and return the SPA for service."

SPA-4-VOLT_SHUTDOWN_NONFATAL

4-Warning

[chars] voltage out of operating range. Nominal [dec]mV value [dec]mV.

MSG_SPA_VOLT_EXP_COMMON The SPA has been shut down to prevent component damage.

-

"Replace the SPA immediately. " "Record the associated messages and return the SPA for service."

IM-3-UNSUPPORTED_DATA

3-Error

Data conversion error [chars] 0x%X

An internal software error has occured when converting the data specified in the message from one representation to another.

asr900-im

LOG_STD_SH_TECH_ACTION

IM_EEPROM-3-FORMAT_ERROR

3-Error

[chars]: [chars]. The EEPROM might require an update.

A format error has been detected in the EEPROM of the indicated IM. The type of error is indicated in the error message.

asr900-im

SPA_EEPROM_STD_BUG_ACTION

IM_EEPROM-3-FIELD_NOT_FOUND

3-Error

[chars]: Failed to find content of field type 0x[hec] with data size = [dec] bytes. The EEPROM might require an update.

System failed to find the content of the indicated field type from the IM EEPROM. The format of the EEPROM of the indicated IM might not be up to date.

spa-infra

SPA_EEPROM_STD_BUG_ACTION

SPA-1-AUTHENTICATION_FAIL

1-Alert

IM authentication failed for slot/bay [dec]/[dec]

This Module may not have been manufactured by Cisco or with Cisco's authorization. This product may contain software that was copied in violation of Cisco's license terms. If your use of this product is the cause of a support issue Cisco may deny operation of the product support under your warranty or under a Cisco technical support program such as Smartnet. Please contact Cisco's Technical Assistance Center for more information.

iomd-infra

LOG_STD_ACTION

SPA-5-IOFPGA_SBE_MEMORY_FAIL

5-Notice

IOFPGA Single Bit Error in RAM memory for slot/bay [dec]/[dec] Auto Recovering the failure.

Soft errors are unintended changes to the values stored in SRAM’s configuration memory of FPGA caused by ionizing radiation. Please refer ‘Soft Error Mitigation Controller’ product guide PG036 for more information. Please contact Cisco's Technical Assistance Center for more information.

spa-infra

LOG_STD_ACTION

SPA-2-IOFPGA_MBE_MEMORY_FAIL

2-Critical

IOFPGA Multi Bit Error in RAM memory for slot/bay [dec]/[dec] Fatal failure. Reloading the IM

Soft errors are unintended changes to the values stored in SRAM’s configuration memory of FPGA caused by ionizing radiation. Please refer ‘Soft Error Mitigation Controller’ product guide PG036 for more information. Please contact Cisco's Technical Assistance Center for more information.

spa-infra

LOG_STD_ACTION

SPA-5-CEMFPGA_SBE_MEMORY_FAIL

5-Notice

CEMFPGA Single Bit Error in RAM memory for slot/bay [dec]/[dec] Auto Recovering the failure.

Soft errors are unintended changes to the values stored in SRAM’s configuration memory of FPGA caused by ionizing radiation. Please refer ‘Soft Error Mitigation Controller’ product guide PG036 for more information. Please contact Cisco's Technical Assistance Center for more information.

spa-infra

LOG_STD_ACTION

SPA-2-CEMFPGA_MBE_MEMORY_FAIL

2-Critical

CEMFPGA Multi Bit Error in RAM memory for slot/bay [dec]/[dec] Fatal failure. Reloading the IM

Soft errors are unintended changes to the values stored in SRAM’s configuration memory of FPGA caused by ionizing radiation. Please refer ‘Soft Error Mitigation Controller’ product guide PG036 for more information. Please contact Cisco's Technical Assistance Center for more information.

spa-infra

LOG_STD_ACTION

SPA-1-DB_AUTHENTICATION_FAIL

1-Alert

Module daughter board authentication failed for slot/bay/board [dec]/[dec]/[dec]

This daughter board may not have been manufactured by Cisco or with Cisco's authorization. This product may contain software that was copied in violation of Cisco's license terms. If your use of this product is the cause of a support issue Cisco may deny operation of the product support under your warranty or under a Cisco technical support program such as Smartnet. Please contact Cisco's Technical Assistance Center for more information.

esg-io-infra

LOG_STD_ACTION

SPA-3-MSG_PARSE_FAILURE

3-Error

Failed to parse incoming message from [chars]

An incoming control message from an IO module failed to get parsed and as a result failed to get handled by the control process running on the host platform. This error message could occur when the software running on the module is incompatible with the host. A solution is to update the module software with a version that is the same or compatible with

see tac details

LOG_STD_ACTION

SPA-5-CELBRN_FPGA_SBE_MEMORY_FAIL

5-Notice

CELBRNFPGA Single Bit Error in RAM memory for slot/bay [dec]/[dec] Auto Recovering the failure.

Soft errors are unintended changes to the values stored in SRAM’s configuration memory of FPGA caused by ionizing radiation. Please refer ‘Soft Error Mitigation Controller’ product guide PG036 for more information. Please contact Cisco's Technical Assistance Center for more information.

spa-infra

LOG_STD_ACTION

SPA-2-CELBRN_FPGA_MBE_MEMORY_FAIL

2-Critical

CELBRNFPGA Multi Bit Error in RAM memory for slot/bay [dec]/[dec] Fatal failure. Reloading the IM

Soft errors are unintended changes to the values stored in SRAM’s configuration memory of FPGA caused by ionizing radiation. Please refer ‘Soft Error Mitigation Controller’ product guide PG036 for more information. Please contact Cisco's Technical Assistance Center for more information.

spa-infra

LOG_STD_ACTION

SPA_FPD-6-IMG_CORRUPTION

6-Information

[chars]: FPD image corruption detected for \[chars]\ ID=[dec] forcing upgrade

The software detected corruption on a FPD image and it is triggering the FPD automatic upgrade mechanism to correct the problem.

spa-infra-fpd

"No Action is required."

SPA_FPD-4-UPGRADE_ABORTED

4-Warning

[chars]: Upgrade aborted for \[chars]\ ID=[dec] - [chars]

The upgrade operation for the FPD image was aborted because the provided image cannot be used by the driver to perform the image programming operation.

spa-infra-fpd

"Make sure that the provide FPD image package for " "the FPD upgrade operation is a valid one for the Cisco IOS release in " "use. This can be verified with the <CmdBold>show upgrade fpd package " "default<NoCmdBold> command to display the required FPD image package " "version for the IOS image."

SPA_FPD-3-GETVER_FAILED

3-Error

[chars]: Failed to get FPD version for \[chars]\ ID=[dec]: [chars].

Failed to get FPD version due to either IPC problem or operation error. The card will be disabled.

spa-infra-fpd

"Check SPA seating and SPA status. " "Ensure compatibility among FPD IOS and possible SPA " "firmware by comparing output of command " "<CmdBold>show hw-module subslot fpd<NoCmdBold> with IOS " "Release Notes. Obtain IOS version by command " "<CmdBold>show version<NoCmdBold>."

SPA_FPD-3-UPGRADE_FAILED

3-Error

[chars]: Failed to upgrade FPD [chars].

The FPD image upgrade operation failed. This error is specific to the SPA. The cause could be a wrong image file error in accessing fpga storage physical interrupt such as power failure or card removal. Depending on SPA type and error cause the card could be in an unusable status. Normally the system automatically reattempts the upgrade and shuts the card after repeated failures.

spa-infra-fpd

"Do not interrupt the system while an FPD " "upgrade is in progress. Obtain the matching FPD package. Refer " "to IOS Release Notes for more information on obtaining the correct " "FPD package for the SPA. Review the output of the RP FPD logs."

SPA_FPD-3-JTAG_ERR

3-Error

[chars]: Failed to program a [chars] FPD image file. Error code 0x%02x.

While attempting to program a SPA FPGA via JTAG bus an error occurs. It could be caused by an outdated carrier card FPGA or SPA connection. It may also flag an internal software error.

spa-infra-fpd

"Retry the upgrade after reseating SPA. " "Verify carrier card FPGA is current. Copy exact the error " "message and report to TAC."

SPA_FPD-3-SW_ERROR

3-Error

NULL

-

spa-infra-fpd

LOG_STD_ACTION

SPA_FPD-3-PWR_OFF_FAILED

3-Error

Failed to power-off [chars] in [chars] for FPD offline upgrade within [dec] seconds.

The power-off operation of the indicated SPA failed within the number of specified seconds. This might indicate that the time used to wait for SPA to power-off is not long enough which can happen if the SPA has a lot of interfaces configured.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the upgrade operation."

SPA_FPD-3-SMM665_CONF_WRITE_ERROR

3-Error

[chars]: Failed to write new configuration into SMM665 device.

The write operation to SMM665 is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the upgrade operation."

SPA_FPD-3-ADM106X_READ_VER_ERROR

3-Error

[chars]: Failed to read version info from ADM106x device - [chars]

The read operation to ADM106x is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Try to reload the SPA with <CmdBold>hw-module subslot<NoCmdBold> " "<CmdArg>slot#/subslot#<NoCmdArg> <CmdBold>reload<NoCmdBold> command " "to correct the failure. If problem persists move the SPA to another " "bay of the carrier card."

SPA_FPD-3-IHEX_PARSE_ERROR

3-Error

NULL

-

spa-infra-fpd

LOG_STD_ACTION

SPA_FPD-3-ADM106X_EEPROM_READ_ERROR

3-Error

[chars]: Failed to read the content of ADM106x [chars] EEPROM section - [chars]

The read operation to ADM106x is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Retry the same operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the operation."

SPA_FPD-3-ADM106X_EEPROM_WRITE_ERROR

3-Error

[chars]: Failed to write new configuration into ADM106x [chars] EEPROM section - [chars]

The write operation to ADM106x is performed through C2W serial interface from SPA carrier card the indicated failure might be caused by busy C2W serial interface.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists remove the configuration of the SPA before trying " "again the upgrade operation."

SPA_FPD-3-ADM106X_EEPROM_VERIFY_ERROR

3-Error

[chars]: Verification of write operation failed in ADM106x [chars] EEPROM section for address 0x[hec] - read value '0x[hec]' expected value '0x[hec]'.

The verification of the write operation has found a mismatch on the EEPROM data. The problem might be an indication of aging effect on the device that cannot longer hold written data.

spa-infra-fpd

"Retry the upgrade operation again later. If the " "problem persists replace the SPA."

SPA_FPD-2-PWR_NO_OK

2-Critical

SPA POWER OK signal is not asserted for [chars] in [chars] for FPD upgrade.

The check for SPA POWER OK signal assertion failed. This might indicate a HW problem with the SPA.

spa-infra-fpd

"Contact your Cisco technical support " "representative to have the SPA replaced."

CBR_SPA-3-NULL_SPA_PTR

3-Error

-

Pointer to a SPA object is NULL.

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_INIT_ERROR

3-Error

[chars] Raptor err [dec]

Raptor driver initialization error

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_ENTRY_FULL

3-Error

[chars] Raptor [chars] mac-filter entry full drop addr %02X.%02X.%02X.%02X.%02X.%02X

Raptor mac filter entry full

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_MAC_ENTRY_FULL

3-Error

[chars] Falcon [chars] mac-filter entry full drop addr %02X.%02X.%02X.%02X.%02X.%02X

Falcon mac filter entry full

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_READY_REG_READ_ERROR

3-Error

[chars] unable to read Raptor ESI READY REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_CLOCK_NOT_READY_ERROR

3-Error

[chars] Raptor ESI Clocks reg:0x%08x

Raptor-ESI clocks are NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_SUP_CTRL_REG_WRITE_ERROR

3-Error

[chars] unable to write to Raptor ESI CONTROL REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_SUP_CHASSIS_SLOT_REG_WRITE_ERROR

3-Error

[chars] unable to write to Raptor ESI CHASSIS SLOT ID REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PLL_CTRL_REG_READ_ERROR

3-Error

[chars] unable to read from Raptor ESI PLL CONTROL REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PLL_CTRL_REG_WRITE_ERROR

3-Error

[chars] unable to write to Raptor ESI PLL CONTROL REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PLL_CTRL_LOCK_ERROR

3-Error

[chars] unable to lock Raptor ESI PLL

Raptor-ESI PLL not locked

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PIC_STATUS_REG_READ_ERROR

3-Error

[chars] unable to read from Raptor ESI PIC STATUS REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_DNLD_FAILED

3-Error

[chars] Raptor-MAC error

Unable to download Raptor-MAC firmware

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PIC_PWR_NOT_GOOD_ERROR

3-Error

[chars] Raptor SUP PIC Power not good

Raptor-ESI PLL not locked

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_READY_REG_READ_ERROR

3-Error

[chars] unable to read Raptor MAC READY REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_CLOCK_NOT_READY_ERROR

3-Error

[chars] Raptor MAC Clocks reg:0x%08x

Raptor-MAC clocks are NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_NOT_READY_ERROR

3-Error

[chars] Raptor ESI Global Ready reg:0x%08x

Raptor-ESI NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_NOT_READY_ERROR

3-Error

[chars] Raptor MAC Global reg:0x%08x

Raptor-MAC Contrpl Plane NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_PIC_CTRL_REG_WRITE_ERROR

3-Error

[chars] unable to write to Raptor MAC PIC CONTROL REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_CFG_REG_WRITE_ERROR

3-Error

[chars] unable to write to Raptor MAC RX/TX CFG REG err [dec]

Unable to communicate with Raptor Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_PIC_CPLD_NOT_READY_ERROR

3-Error

[chars] Raptor MAC PIC CPLD error

Raptor-MAC PIC CPLD NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SFP_SUB_INIT_ERROR

3-Error

[chars] SFP Subblock create error

Unable to create SFP sub-block

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-CORTINA_PHY_DEV_CREATE_ERROR

3-Error

[chars] Cortina PHY device create error port [dec]/[dec]/[dec]

Unable to create Cortina PHY device object

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-CORTINA_PHY_DEV_ATTACH_ERROR

3-Error

[chars] Cortina PHY device attach error port [dec]/[dec]/[dec]

Unable to attach Cortina PHY device object

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-CORTINA_PHY_DEV_INIT_ERROR

3-Error

[chars] Cortina PHY device init error port [dec]/[dec]/[dec]

Unable to downaload firmware to Cortina PHY device

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-XCVR_MISSING_HWIDB_ERROR

3-Error

[chars] XCVR Missing interface object port [dec]/[dec]/[dec]

Unable to downaload firmware to Cortina PHY device

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-XCVR_POP_DEF_PARAMS_ERROR

3-Error

[chars] XCVR Unable to poulate default parameters port [dec]/[dec]/[dec]

Unable to poulate default XCVR SM parameters

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-XCVR_SM_LAUNCH_ERROR

3-Error

[chars] XCVR Unable to launch SM port [dec]/[dec]/[dec]

Unable to launch XCVR SM

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-DTI_CLIENT_DNLD_ERROR

3-Error

[chars] DTI Client error

Unable to download DTI client firmware

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_UNKN_INIT_ERROR

3-Error

[chars] Unknown SPA Init phase error

Unknown SPA Init phase

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_PLUGIN_INIT_ABORT_ERROR

3-Error

[chars] SPA Plugin Init Abort error

Unknown SPA Init phase

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-RAPTOR_ESI_PCIE_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from PCIE Wrapper\n\ Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_PROCBUS_MASTER_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from ProcBus Master\n\ Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_SERDES_PKTBUS_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Serdes PacketBus\n\ Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_INGRESS_SCH_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Ingress\n\ Scheduler Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_EGRESS_SCH_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Egress\n\ Scheduler Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_EGRESS_HDR_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Egress\n\ Header Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_FC_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Flow\n\ Control Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_ESI_PRST_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received Partial reset\n\ Module in Raptor-ESI FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_PRST_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received Partial reset\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_PROCBUS_SLAVE_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Proc Bus\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_10G_MAC_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from 10GE MAC\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_SERDES_PKTBUS_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Serdes Packet Bus\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_SEM_LO_INTERRUPT

7-Debug

[chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec]

Low Priority Interrupt received from SEM\n

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_RLDRAM_IF_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from RLDRAM Interface\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_FIFO_CTL_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from FIFO Control\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_INGRESS_QOS_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from Ingress QoS\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_FIFO_CTRL_MUX_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from FIFO Control MUX\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_MAC_MAC_SCH_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from MAC Scheduler\n\ Module in Raptor-MAC FPGA

-

LOG_STD_DBG_ACTION

CBR_SPA-3-RAPTOR_ESI_PRST_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received Partial reset\n\ Module in Raptor-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_PRST_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received Partial reset\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_ESI_PCIE_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from PCIE Wrapper\n\ Module in Raptor-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_ESI_CLOCK_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from Clock\n\ Module in Raptor-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_ESI_PROCBUS_MASTER_HI_INTERRUPT

3-Error

[chars] [chars]

HIGH Priority Interrupt received from ProcBus Master\n\ Module in Raptor-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_ESI_SERDES_PKTBUS_HI_INTERRUPT

3-Error

[chars] [chars]

Hign Priority Interrupt received from Serdes PktBus\n\ Module in Raptor-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_ESI_INGRESS_SCH_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from Ingress Scheduler\n\ Module in Raptor-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_PROCBUS_SLAVE_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from ProcBus Slave\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_CLOCK_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from Clock\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_MDIO_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from MDIO\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_XFI_IF_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from XFI\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_SERDES_PKTBUS_HI_INTERRUPT

3-Error

[chars] [chars]

HIGH Priority Interrupt received from Serdes PktBus\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_RLDRAM_HI_INTERRUPT

3-Error

[chars] [chars]

HIGH Priority Interrupt received from RLDRAM\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_SEM_HI_INTERRUPT

3-Error

[chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec]

HIGH Priority Interrupt received from SEM\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RAPTOR_MAC_FIFO_CTL_HI_INTERRUPT

3-Error

[chars] [chars]

HIGH Priority Interrupt received from FIFO Control\n\ Module in Raptor-MAC FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_RFSW_POWER_ERROR

3-Error

Power circuit error on [dec]/[dec] voltages:[chars]

A power circuit error received from RFSW PIC\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-4-SPA_RFSW_WATCH_DOG_TIMEOUT

4-Warning

Watch Dog Timeout on [dec]/[dec]

A Watch Dog Timeout error received from RFSW PIC\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_RFSW_TEMPERATURE_ERROR

3-Error

Temperature Error on [dec]/[dec] temperature:[chars]

A Temperature error received from RFSW PIC\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_RFSW_RELAY_FAILURE

3-Error

Relay failure on [dec]/[dec] relay status:[chars]

A Relay failure error received from RFSW PIC\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_RFSW_I2C_FAILURE

3-Error

I2C failure on [dec]/[dec] I2C status:[chars]

An I2C failure error received from RFSW PIC\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-RAPTOR_INTERRUPT_DISABLE

7-Debug

Interrupt throttled for: [chars] [chars]

Interrupt throttled\n

-

LOG_STD_DBG_ACTION

CBR_SPA-7-RAPTOR_INTERRUPT_ENABLE

7-Debug

Interrupt enabled for: [chars] [chars]

Interrupt unthrottled\n

-

LOG_STD_DBG_ACTION

CBR_SPA-3-RAPTOR_PLL_LOS

3-Error

[chars]

Raptor PLL LOS

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-4-RAPTOR_PLL_MIS

4-Warning

[chars]

Raptor PLL clock soure not come from active RP\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_RFSW_UPGRADE_UNSUPPORTED

3-Error

unsupported firmware upgrade on [dec]/[dec] firmware version :[hec]\n

RFSW PIC firmware can not be upgraded\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-6-SPA_DPIC_UPGRADE_UNSUPPORTED

6-Information

unsupported firmware upgrade on [dec]/[dec]\n

DIGI PIC firmware can not be upgraded\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-SPA_DPIC_UPGRADE_NOSPACE

3-Error

no enough space in harddisk to store digital pic image \[dec]MB free [dec]MB needed\n

DIGI PIC firmware can not be upgraded\n\ due to harddisk is full\n

-

"Free up some space in harddisk to \store digital pic image."

CBR_SPA-3-RAPTOR_LED_ERROR

3-Error

SUP-PIC [dec]/[dec] LED err

SUP-PIC LED initialization error

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-DPIC_BOOT_REASON

3-Error

DPIC [dec]/[dec]: [chars]

DPIC Boot Error Reason

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-0-DPIC_EMERG

0-Emergency

[chars]-[chars]

Receive some EMERG message from DPIC

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-1-DPIC_ALERT

1-Alert

[chars]-[chars]

Receive some ALERT message from DPIC

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-2-DPIC_CRIT

2-Critical

[chars]-[chars]

Receive some CRITICAL message from DPIC

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-DPIC_ERR

3-Error

[chars]-[chars]

Receive some ERR message from DPIC

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-4-DPIC_WARNING

4-Warning

[chars]-[chars]

Receive some WARNING message from DPIC

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-5-DPIC_NOTICE

5-Notice

[chars]-[chars]

Receive some NOTICE message from DPIC

-

LOG_STD_NO_ACTION

CBR_SPA-6-DPIC_INFO

6-Information

[chars]-[chars]

Receive some INFO message from DPIC

-

LOG_STD_NO_ACTION

CBR_SPA-7-DPIC_DEBUG

7-Debug

[chars]-[chars]

Receive some DEBUG message from DPIC

-

LOG_STD_DBG_ACTION

CBR_SPA-3-DPIC_NGIO_ERROR

3-Error

NGIO connection between IOMd and DPIC [dec]/[dec] is down!

NGIO is down between IOMd and DPIC

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-DPIC_NGIO_KEEPALIVE

3-Error

NGIO keepalive between IOMd and DPIC [dec]/[dec] timeout! \%lu NGIO rx %lu ping successes %lu ping failures

NGIO keepalive is timeout.

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-5-DPIC_RESET

5-Notice

DPIC [dec]/[dec] will be recovered from unexpected state

DPIC can not be online in 5 min

-

LOG_STD_NO_ACTION

CBR_SPA-7-FALCON_INTERRUPT_DISABLE

7-Debug

Interrupt throttled for: [chars] [chars]

Interrupt throttled\n

-

LOG_STD_DBG_ACTION

CBR_SPA-7-FALCON_INTERRUPT_ENABLE

7-Debug

Interrupt enabled for: [chars] [chars]

Interrupt unthrottled\n

-

LOG_STD_DBG_ACTION

CBR_SPA-3-FALCON_PLL_LOS

3-Error

[chars]

Falcon PLL LOS

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-4-FALCON_PLL_MIS

4-Warning

[chars]

Falcon PLL clock soure not come from active RP\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RETIMER_PHY_DEV_CREATE_ERROR

3-Error

[chars] Retimer PHY device create error quad [dec]/[dec]/[dec]

Unable to create Retimer PHY device object

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RETIMER_PHY_DEV_ATTACH_ERROR

3-Error

[chars] Retimer PHY device attach error quad [dec]/[dec]/[dec]

Unable to attach Retimer PHY device object

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-RETIMER_PHY_DEV_INIT_ERROR

3-Error

[chars] Retimer PHY device init error quad [dec]/[dec]/[dec]

Unable to init Retimer PHY device

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_INIT_ERROR

3-Error

[chars] Falcon err [dec]

Falcon driver initialization error

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_RDY_REG_READ_ERR

3-Error

[chars] unable to read Falcon ESI READY REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_CLK_NOT_RDY_ERR

3-Error

[chars] Falcon ESI Clocks reg:0x%08x

Falcon-ESI clocks are NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_SUP_CTRL_REG_WR_ERR

3-Error

[chars] unable to write to Falcon ESI CONTROL REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_SUP_CHASSIS_SLOT_REG_WR_ERR

3-Error

[chars] unable to write to Falcon ESI CHASSIS SLOT ID REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PLL_CTRL_REG_READ_ERR

3-Error

[chars] unable to read from Falcon ESI PLL CONTROL REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PLL_CTRL_REG_WR_ERR

3-Error

[chars] unable to write to Falcon ESI PLL CONTROL REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PLL_CTRL_LOCK_ERR

3-Error

[chars] unable to lock Falcon ESI PLL

Falcon-ESI PLL not locked

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PIC_STATUS_REG_READ_ERR

3-Error

[chars] unable to read from Falcon ESI PIC STATUS REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-ESI_PIC_PWR_NOT_GOOD_ERR

3-Error

[chars] Falcon SUP PIC Power not good

Falcon-ESI PLL not locked

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_READY_REG_READ_ERR

3-Error

[chars] unable to read Falcon MAC READY REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_CLK_NOT_RDY_ERR

3-Error

[chars] Falcon MAC Clocks reg:0x%08x

Falcon-MAC clocks are NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_NOT_RDY_ERR

3-Error

[chars] Falcon MAC Global reg:0x%08x

Falcon-MAC Contrpl Plane NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_PIC_CTRL_REG_WR_ERR

3-Error

[chars] unable to write to Falcon MAC PIC CONTROL REG err [dec]

Unable to communicate with Falcon Device driver

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-MAC_PIC_CPLD_NOT_RDY_ERR

3-Error

[chars] Falcon MAC PIC CPLD error

Falcon-MAC PIC CPLD NOT Ready

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_ESI_PCIE_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from PCIE Wrapper\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_ESI_QPLL_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from PCIE Wrapper\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_SEM_LO_INTERRUPT

7-Debug

[chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec]

Low Priority Interrupt received from SEM\n

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_PWM_DIST_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from PWM DIST\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_FP_10G_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from FP 10G\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_FP_INGR_PAR_TOP_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from FP INGRESS PARSER TOP\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_FP_EGR_SCH_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from FP EGRESS SCHEDULER\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_ESI_FC_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from ESI FC\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_INGR_SCH_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from INGRESS SCHEDULER\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_EGR_DISPATCH_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from EGRESS DISPATCHER\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_MAC_LOCAL_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from LOCAL MAC\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_MAC_PEER_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from REMOTE MAC\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_INGR_BUF_LOCAL_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from INGRESS LOCAL BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_INGR_BUF_PEER_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from INGRESS REMOTE BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_EGR_BUF_LOCAL_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from EGRESS LOCAL BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_EGR_BUF_PEER_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from EGRESS REMOTE BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_INGR_PARSER_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from INGRESS PARSER\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_PAR_RST_LO_INTERRUPT

7-Debug

[chars] [chars]

Low Priority Interrupt received from PAR RST\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_ESI_PCIE_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from PCIE Wrapper\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_ESI_CLOCK_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from CLOCK\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_SEM_HI_INTERRUPT

3-Error

[chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec]

HIGH Priority Interrupt received from SEM\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-7-FALCON_GB_MDIO_IF_HI_INTERRUPT

7-Debug

[chars] [chars]

High Priority Interrupt received from GB MDIO\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_FP_INGR_PAR_TOP_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from FP\n\ INGRESS PARSER TOP Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_FP_EGR_SCH_TOP_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from FP\n\ EGRESS SCHDULER TOP Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_INGR_SCH_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from INGRESS SCHDULER\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_EGR_DISPATCH_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from EGRESS DISPATCH\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_MAC_LOCAL_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from LCOAL MAC\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_MAC_PEER_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from PEER MAC\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_INGR_BUF_LOCAL_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from INGRESS LOCAL BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_INGR_BUF_PEER_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from INGRESS REMOTE BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_EGR_BUF_LOCAL_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from EGRESS LOCAL BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_EGR_BUF_PEER_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from EGRESS REMOTE BUF\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_INGR_PARSER_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from INGRESS PARSER\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_PMBIST_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from PM BIST\n\ Module in Falcon FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_PAR_RST_HI_INTERRUPT

3-Error

[chars] [chars]

High Priority Interrupt received from PAR RST\n\ Module in Falcon-ESI FPGA

-

LOG_STD_SH_TECH_ACTION

CBR_SPA-3-FALCON_MODE_XCVR_MATCH_ERR

3-Error

SUP-PIC [dec]/1 port [dec] interface mode mismatched: QSFP type is [chars] interface mode is [chars]

SUP250 backhaul interface support two kinds of transceiver: QSFP28 and QSFP+. If the backhaul mode is configured as 100GE mode with commad 'cable sup250-ifmod 100GE' but insert a QSFP+ transceiver. Or the backhaul mode is configured as 10GE mode with comand 'cable sup250-ifmod 10GE' but insert a QSFP28 transceiver. This error message will be reported.

-

"Change configration to another backhaul mode or replace other type of transceiver."

CBR_SPA-3-RAPTOR_PRST_HIT_CONSTANT_CRC

3-Error

Detected continual CRC errors on SUP-PIC [dec]/1 port [dec] or port [dec]!

SUP160 backhaul interface's recover service was blocked because there are continual CRC errors on corresponding interface.

-

"Check related link including fiber line SFP module etc..."

UEA_CHOC_DSX-3-NULL_SPA_PTR

3-Error

-

The pointer to a SPA value is of a null value.

uea-im-tdm

LOG_STD_SH_TECH_ACTION

RMGR-3-OUT_OF_TCAM_IPV4_ROUTE

3-Error

Out of tcam resources to execute command

Number of IPv4 routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 routes configured " "to supported scale"

MCASTV4-3-OUT_OF_TCAM_IPV4_MCAST

3-Error

Out of tcam space

Number of IPv4 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 mcast routes " "configured to supported scale"

MCASTV6-3-OUT_OF_TCAM_IPV6_MCAST

3-Error

Out of tcam space

Number of IPv6 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv6 mcast routes " "configured to supported scale"

MPLS-3-OUT_OF_LABEL3_SPACE

3-Error

Out of resource to create labels

Number of empls 3d labels exceeded supported scale

asr903-mpls

"Please reduce the number of empls 3d labels to " "supported scale"

MPLS-3-INCORRECT_LENTRY_ENCAP

3-Error

[chars]: mplsd swap 1 encap [dec]

Lentry has incorrect encap

asr903-mpls

"Please collect this error message tracebacks " "and nile mgr logs"

MPLS-3-OUT_OF_LABEL_SPACE

3-Error

Out of resource to create labels

Number of empls intd labels exceeded supported scale

asr903-mpls

"Please reduce the number of empls intd labels to " "supported scale"

MPLS-3-MAX_PW_EXCEEDED

3-Error

Number of PW's exceeded supported limit [dec]

Number of empls intd labels exceeded supported scale

asr903-mpls

"Please reduce the number of PW's to supported scale"

MPLS-3-MPLS_MTU_ALLOC_FAIL

3-Error

Out of resource to allocate mpls mtu

mpls mtu exceeded supported scale

asr903-mpls

"Please reduce the number of mpls mtu configured values" "to supported scale"

MPLS-3-FRR_BDI_UNSUPPORTED

3-Error

FRR not enabled on [chars]. Unsupported EFP and trunk EFP count [dec]. Supported 1

LFA FRR support on ASR903 for BDI interface is available with just one EFP or trunk EFP

asr903-mpls

"shutdown the BDI interface. Remove all the " " EFPs/TEFPs under the BDI. Create just one EFP or TEFP." " no shutdown the BDI interface"

MPLS-4-PIC_BDI_UNSUPPORTED

4-Warning

BGP PIC not enabled on [chars]: [chars]

Hardware could not be programmed for BGP PIC support on BDI interface

asr903-mpls

"Collect the logs and contect Cisco TAC"

MPLS-3-MPLS_STALE_LABEL

3-Error

Stale Label : [dec] Neither Allocated nor Deallocated

Stale Label Neither Allocated nor Deallocated

asr903-mpls

"Don't collect the stats for this instance"

CEF-3-NILE_CEF_MAX_VRF_EXCEEDED

3-Error

Number of VRF instances already exceeded allowed limit [dec]

Number of vrf instances exceeded supported platform scale

firmware

"Please reduce the number of vrf instances" "to scale to platform supported scale"

QOSMGR-3-ASIC_PROGRAMMING_FAIL

3-Error

Fails to program the ASIC for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_PROGRAMMING_FAIL

3-Error

Fails to program TCAM for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_EXHAUSTION

3-Error

Internal Error in resource allocation

The system is running out of TCAM entries to support the number of traffic classes in the policy-map. The maximum number of TCAM entries is platform dependent.

firmware

"Reduce the number of classes in attached policy-maps"

QOSMGR-3-LABEL_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of QoS label to support the number of traffic classes in all attached policy-maps.

firmware

"Reduce the number of distinctive class-maps matches " "or 'set' actions in attached policy-maps"

QOSMGR-4-STATISTICS_FAIL

4-Warning

Internal Error in reading statistics

Can not access to HW to read statistics successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TDM_OC_HIERARCHY_UNSUPPORTED

3-Error

Only two-level hierarchy is supported on TDM/OC3/OC12 interfaces

Unsupported QoS hierarchy on TDM/OC3/OC12 interfaces

firmware

"Change config to reduce to two-level policy"

QOSMGR-3-POLICER_PROGRAMMING_FAIL

3-Error

Fails to program HW policer

Can not access to HW successfully.

firmware

""

QOSMGR-4-POLICER_EXCEEDING_HW

4-Warning

Policer configuration has exceeded hardware limitation for policymap [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-3-L4OP_ACL_PORT_CONFLICT

3-Error

Port ranger is already allocated to ACL on this interface.\n QoS policy configruation failed. Remove QoS command from interface[chars]

ACL configured on this interface uses Port ranger. Remove ACL configuration apply QoS first and then configure ACL

firmware

"Remove ACL configured on interface."

QOSMGR-3-L4OP_QOS_PORT_CONFLICT

3-Error

Port ranger is allocated to QOS on this interface port expansion used for configured ACL [chars]

IPv6 QOS configured on this interface uses Port ranger

firmware

"Remove IPv6 QOS configured on interface."

QOSMGR-3-L4OP_PORT_RANGE_VCU_PER_PORT_EXCEEDED

3-Error

Port range entry on this interface has exceeded maximum permitted 8 operations further l4 match ACE will be ignored[chars]

Interface already has maximum permitted 8 l4 operations

firmware

"Configure only 8 l4 match ACE per interface"

QOSMGR-3-L4OP_ACL_RESERVATION_EXHAUSTED

3-Error

Port ranger resource reserved for ACL exhausted port expansion used [chars]

Port ranger is shared between ACL and v6 QOS ACL. ACL reservation exhausted

firmware

"Remove ACL configuration or increase reservation through ROMMON variable" " QOS_PORTRANGE_RESOURCE"

QOSMGR-3-L4OP_QOS_RESERVATION_EXHAUSTED

3-Error

Port ranger resource reserved for QOS exhausted. policy configuration failed \nRemove other IPv6 QOS configuration or increase reservation through ROMMON [chars]

Port ranger is shared between ACL and v6 QOS ACL. QOS reservation exhausted

firmware

"Remove other IPv6 QOS ACL configuration or increase reservation through ROMMON" " QOS_PORTRANGE_RESOURCE"

QOSMGR-3-INGRESS_QOS_HANDLE_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-handle to support specified policy-map.

firmware

""

QOSMGR-3-INGRESS_QOS_PROFILED_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-profiled to support the specified policy-map.

firmware

""

QOSMGR-3-SCHEDULER_PROGRAMMING_FAIL

3-Error

Fails to program HW scheduler

Can not access to HW successfully.

firmware

""

QOSMGR-4-QUEUE_EXCEEDING_HW

4-Warning

Queue configuration has exceeded hardware limitation for policymap [chars]

The system is running out of output queues to support the specified policy-map.

firmware

"Reduce the number of the traffic classes in attached output policy-maps."

QOSMGR-4-INVALID_POLICYMAP_DUE_NON_QOS_EVENT

4-Warning

The policy-map [chars] is detached due to the event [chars].

The attached policy-map becomes invalid due to the change of the port speed.

firmware

"Change the shaping/bandwidth of the output policy-map and re-attach to the interface ."

QOSMGR-3-OUT_OF_TCAM_RESOURCES

3-Error

Out of tcam resources to execute command

Lack of tcam resources due to higher tcam resource requirements

firmware

"Change config to reduce tcam entry usage"

QOSMGR-3-PROFILES_EXHAUSTED

3-Error

Out of rm profiles to execute command

No free RM profile to accommodate the request

firmware

"Change config to reduce or reuse RM profiles"

QOSMGR-3-QUEUE_FLUSH_FAILED

3-Error

Queue-Flush not successful

Scheduler unable to flush the queue

firmware

"Remove any shape configuration for the queue"

QOSMGR-3-MAX_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum queue-limit commands per class

Trying to exceed the maximum queue-limit commands allowed per class

firmware

"Try reducing queue-limit commands under the class"

QOSMGR-3-MAX_QUALIFIED_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum qualified queue-limit commands per class

Trying to exceed the maximum qualified queue-limit commands allowed per class

firmware

"Try reducing qualified queue-limit commands " "under the class"

QOSMGR-3-UNSUPPORTED_QLIMIT_UNITS

3-Error

Qlimit unit other than usec & byte is not supported

Trying to configure a qlimit unit other than bytes or usec

firmware

"Configure qlimit in terms of bytes or usec"

QOSMGR-3-QLIMIT_VALUE_OUT_OF_RANGE

3-Error

Qlimit value is out of range

Trying to configure a qlimit value outside the supported range

firmware

"Configure qlimit value within supported range"

QOSMGR-3-QLIMIT_LEVEL_ERROR

3-Error

Qlimit command not supported in non-leaf classes

Trying to configure qlimit in a non leaf class

firmware

"Configure qlimit only in leaf classes"

QOSMGR-3-MANUAL_SHAPE_EXCEEDS_SPEED

3-Error

Invalid policy-map detected during interface speed change

Shape value in policy exceeds port speed

firmware

"Configure lesser shape value which will not " "exceed interface speed"

QOSMGR-3-BANDWIDTH_OVERSUBSCRIBED

3-Error

Bandwidth oversubscribed in the interface

Sum of committed bandwidth at a particular level exceeds the sum total of interface's max bandwidth

firmware

"Reduce the committed bandwidth to be less that " "interface's max bandwidth"

QOSMGR-3-SHAPE_UNDERFLOW

3-Error

New shape/speed value is less than the total bandwidth configured in the interface

Shape/speed configured is less than the total bandwidth configured in the interface

firmware

"Increase the shape/speed value or reduce " "the bandwidth configured in the child classes"

QOSMGR-3-BANDWIDTH_LEVEL_ERROR

3-Error

Bandwidth command not acceptable at interface level

Hardware does not support bandwidth at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-PRIORITY_LEVEL_ERROR

3-Error

Priority command not acceptable at interface level

Hardware does not support priority at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-BANDWIDTH_SHAPE_ERROR

3-Error

Bandwidth configured is greater than shapePIR of the class

Bandwidth should not be greater than shape value

firmware

"Reduce the bandwidth value to less than" " class's shapePIR value"

QOSMGR-3-BANDWIDTH_PARENT_SHAPE_ERROR

3-Error

Sum of bandwidths is greater than parent class's shapePIR

Total bandwidth of the classes at the same level exceeds the parent class's shapePIR value

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_PARENT_ERROR

3-Error

Sum of bandwidths is greater than parent class's bandwidth

Total bandwidth of the classes at the same level exceeds the parent class's bandwidth

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_CHILD_ERROR

3-Error

Bandwidth in one of the children class is greater than input bandwidth

Children class's bandwidth should not be greater

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-PROFILE_EXHAUST

3-Error

No free scheduler profiles available in hardware

With the new configuration there is no free profile available in the HW this could be because of dissimilar profiles configured at the same hierarchy level

firmware

"Change the config value to closest existing config"

QOSMGR-3-EFP_SHAPE_RESTRICTION

3-Error

EFP policies cannot have shape command at physical level and more than one logical level classes

Since the HW does not support four level hierarchy EFP policies sit in pseudo level between Physical and Logical level

firmware

"Either remove vlan hierarchy in the EFP policy or" " do not configure shape command at physical level"

QOSMGR-3-SHAPE_PARENT_ERROR

3-Error

Shape value is greater than parent class's shape or interface's speed

Parent class's shape value cannot be smaller than current

firmware

"Configure shape value lesser than parent class's" " shape or interface's speed"

QOSMGR-3-SHAPE_CHILD_ERROR

3-Error

One of children class's shape config is higher

Children class's shape should not be higher than current

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_CHILD_BANDWIDTH_ERROR

3-Error

Bandwidth in one of the children class is greater than input shape value

Children class's bandwidth should not be higher than input

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_BANDWIDTH_PERCENT_ERROR

3-Error

Shape - Bandwidth-percent values inconsistent in the hierarchy calculated bandwidth will exceed shape

Because of this new shape command Bandwidth percent configured in one of children class will get more value than its manually configured shape. Please note that bandwidth percent is calculated from parent's shapePIR

firmware

"Either configure higher shape value or " " reduce violating bandwidth-percent value"

QOSMGR-3-LOGICAL_RESOURCE_EXHAUSTED

3-Error

Logical level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused logical level classes"

QOSMGR-3-QUEUE_EXHAUSTED

3-Error

Class level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused class level classes"

QOSMGR-3-EQOS_CXT_EXCEEDED

3-Error

Maximum Egress QosContexts consumed in the Bridge-Domain

Number of Egress QoS vlan matches exceeds the maximum allowed in the Bridge-Domain

firmware

"Reduce the number of Egress QoS vlan" " matches in the Bridge-Domain and try again"

QOSMGR-3-PROTOCOL_NOT_SUPPORTED_FOR_POLICY

3-Error

The configured protocol is not supported in QoS policy

Configured protocol is not supported for QoS Policy. Traffic will be matched with alternative clas-maps/class-default

firmware

" Unconfigure the ACE with unsupported protocol" " detach and re-attach the policy"

QOSMGR-3-L4OP_ACL_NEQ_CONFLICT

3-Error

NEQ L4 operation not supported

Trying to configure NEQ operation.

firmware

"Remove QOS ACL configured on interface."

-

3-Error

fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr

-

-

-

-

3-Error

fmt \extern const struct message_ msg_ ## fac ## _ ## name

-

-

-

IPC-2-NOMEM

2-Critical

No memory available for [chars]

The IPC protocol subsystem could not obtain the memory it needed.

ipc

"If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt. To display IPC " "usage enter <CmdBold>show ipc queue<noCmdBold> at the prompt"

IPC-2-TEST

2-Critical

IPC test: [chars]

The IPC test routines.

ipc

"IPC test only - no action required."

IPC-2-INVALIDZONE

2-Critical

Invalid IPC Zone 0x[hec].

Some operation is attempted on a zone ID not known to IPC

ipc

"show tech-support ipc"

IPC-4-GET_PAK_MSG

4-Warning

Failed for message size [dec]

System unable to allocate IPC message of required size.

ipc

"If this error message recurs copy the error message exactly" " as it appears on the console or in the system log contact" " your Cisco technical support representative with the" " gathered information." "\n\nTo display total memory usage for a router enter " "<CmdBold>show memory summary<noCmdBold> at the privileged " "command line prompt. To display buffer usage enter " "<CmdBold>show buffers<noCmdBold> at the prompt. To display IPC " "usage enter <CmdBold>show ipc queue<noCmdBold> at the prompt"

IPC-4-CONSISTENCY

4-Warning

Consistency check failed for [chars] 0x[hec]

Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures.

ipc

"show tech-support ipc"

IPC-4-MESSAGE_ERR

4-Warning

Consistency check failed for IPC Message. IPC message 0x[hec] and port information 0x[hec] differ

Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures.

ipc

"show ipc ports"

IPC-5-SLAVELOG

5-Notice

VIP-[chars]

The Cisco IOS software running on a Versatile Interface Processor VIP card generated this message. The error message has been

high-vip

"This is actually a Cisco IOS error message from a VIP. Handle " "it as indicated by the text after the 'VIP-' string in the " "error message."

IPC-5-NODELFUNC

5-Notice

Failed to intialize IPC client

An IPC application cannot be initialized because its initialization\n function does not appear in the IPC initialization list.

ipc

"show tech-support ipc"

IPC-5-NULLDELFUNC

5-Notice

Invalid registration

An IPC application has attempted to register NULL function in the IPC initialization list.

ipc

"show tech-support ipc"

IPC-5-NULL

5-Notice

[chars] [chars]=0x[hec] [chars] 0x[hec]

IPC module could not find an IPC entity that is expected to be existing always

ipc

"show tech-support ipc"

IPC-4-NOPORT

4-Warning

Port Not Found. [hec] --> [hec] Index:[hec] Seq: [dec] flags: [hec] size: [dec]

IPC Received a message which is destined for a port that cannot be found by IPC

ipc

"Capture 'sh ipc status' 'sh ipc ports' and" " 'deb ipc errors' outputs and contact TAC"

IPC-5-MSG_NULL

5-Notice

[chars]

IPC message returned is Null

ipc

"show tech-support ipc"

IPC-5-INVALID

5-Notice

[chars] Dest Port 0x[hec] Session 0x[hec] Source 0x[hec]

While processing an incoming message IPC encountered invalid data in its internal data structures.

ipc

"show tech-support ipc"

IPC-5-QFULL

5-Notice

Q=0x[hec] [chars] [dec]

IPC queue is full.

os-ipc

LOG_STD_SH_TECH_ACTION

IPC-2-UNLOCK

2-Critical

Unlock done on already unlocked element 0x[hec]

An internal inconsistency was found in some IPC data structures.

ipc

"show tech-support ipc"

IPC-2-LOCK

2-Critical

Lock done a deleted element 0x[hec]

An internal inconsistency was found in some IPC data structures.

ipc

"show tech-support ipc"

IPC-2-CANT_SEND

2-Critical

[chars]: Cannot send IPC message from 0x[hec] to 0x[hec]: info 0x[hec]

An error occurred when sending IPC message

ipc

"show tech-support ipc"

IPC-2-NO_ACK_HANDLER

2-Critical

No handler for ACK with data for port [hec].

The IPC receiver appended data to an ACK. But at the sender there is no corresponding ACK handler.

ipc

"show tech-support ipc"

IPC-2-NODISPATCH

2-Critical

Message for [hec].[hec] has no receive queue or dispatch routine

The IPC user failed to provide any means of handling the received message.

ipc

show ipc ports

IPC-3-DELETED

3-Error

Attempt to delete an IPC message 0x[hec] a second time

-

-

-

IPC-2-ONINT

2-Critical

Invalid operation at interrupt level: [chars] [hec]

Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at the interrupt level.

ipc

show ipc ports

IPC-3-NOBUFF

3-Error

The [chars] IPC message header cache is empty

The specified IPC message header cache is empty and an incoming IPC message may be dropped as a result.

ipc

"show tech-support ipc"

IPC-3-GIANT

3-Error

Request for giant IPC packet denied. Request size = [dec]

Someone requested a message that was too large for the IPC system

ipc

"show tech-support ipc"

IPC-3-LOWBUFF

3-Error

The main IPC message header cache below application reserve count [dec].

-

-

-

IPC-2-PRECLOSE

2-Critical

IPC port pre-closure overflow : 0x[hec] : 0x[hec]

An application attempts to close an ipc port when there are messages pending in retransmit queue and ipc defer table overflows.

ipc

"show ipc ports open"

IPC-2-BADSHARE

2-Critical

Bad refcount in [chars] ptr=[hec] count=[dec]

A reference count is used to track the usage of IPC messages. A function increments the count when it begins to use a message and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be zero or negative.

ipc

"show tech-support ipc"

IPC-5-INVALIDINPUT

5-Notice

[chars]

IPC API is called with invalid argument.

os-ipc

LOG_STD_RECUR_ACTION

IPC-5-RPCFULL

5-Notice

Cannot hold RPC message port: [hex] index: [dec] type: [hex]

An RPC request for an application could not be added to the RPC request table because pending requests have filled the RPC request table.

ipc

"show tech-support ipc"

IPC-5-REGPORTFAIL

5-Notice

[chars] [chars]=0x[hec] [chars]=0x[hec]

IPC failed to register the control port

ipc

LOG_STD_RECUR_ACTION

IPC-5-WATERMARK

5-Notice

[dec] messages pending in [chars] for the port [chars][hec].[hec] from source seat [hec]

-

-

-

IPC-2-NOBOOL

2-Critical

Boolean NULL in IPC message: [hec].

A watched boolean that was allocated while sending the message is found to be NULL when an ACK arrived.

ipc

show ipc status

IPC-5-NOCALLBACK

5-Notice

[chars]: Flow control callback function is not provided by IPC Client [chars]

An IPC application cannot be controlled if flow need to be slowed down. This might result in drop of IPC packets

ipc

"show ipc ports"

IPC-3-APP_IPC_FAIL

3-Error

[chars] failed. IPC Error: [chars] [dec]

IPC Application Process failed to do some operation with the IPC Layer. The message includes the error code from ipc layer

ipc

show ipc status

IPC-3-ISSU_ERROR

3-Error

[chars] failed with error code [dec] for seat [hec]

ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library

os-ipc

show issu fsm

IPC-3-ISSU_API_ERR

3-Error

[chars] failed with error code [dec]

ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library

os-ipc

show issu client

IPC-5-NULLBPHANDLER

5-Notice

Passed Null backpressure handler

The maximum message timeout for an IPC message exceeds 2 minutes

ipc

"Capture 'sh version' and contact TAC"

IPC-5-SEND_APP_MSG_FAILED

5-Notice

Send message to peer for [chars] failed. Reason: [chars]

Client using IPC App Port has not been able to send message

ipc

"If the reason is 'no such port' then this may be caused because" " of the difference in the versions of IOS running on Active" " and the standby. Any other reason please collect 'sh ipc stat'" " 'sh ipc rpc' 'sh ipc port' on active and standby RPs and " " contact tac"

IPC-6-STATEFUL

6-Information

[chars]

A Stateful IPC Event occurred

ipc

""

IPC-2-INITFAILED

2-Critical

[chars]

IPC Resource Management Initialization failed

ipc

"This is a critical failure for IPC functionality." "Capture 'sh version' and contact TAC"

IPC-6-MAXRPCTIMEOUT

6-Information

Maximum RPC timeout value [dec] seconds set for port 0x[hec]

The maximum RPC timeout for an IPC message exceeds the maximum expected value of 10 minutes. If you are using MOS IPC it may report some fake RPC timeouts at the receiver

ipc

"Capture 'show techsupport ipc' and contact TAC"

SISF-3-INTERNAL

3-Error

Internal error [chars]

An internal software error occurred.

sisf

LOG_STD_ACTION

SISF-6-ENTRY_CREATED

6-Information

Entry created [chars]

An entry was created in the binding table

sisf

"This is an informationnal message"

SISF-6-ENTRY_DELETED

6-Information

Entry deleted [chars]

An entry was created in the binding table

sisf

"This is an informationnal message"

SISF-6-ENTRY_CHANGED

6-Information

Entry changed [chars]

An entry was changed in the binding table

sisf

"This is an informationnal message"

SISF-6-ENTRY_MAX_ORANGE

6-Information

Reaching 80%% of max adr allowed per [chars]

Reached 80% of maximum # addresses for the target

sisf

"A client is approaching red zone and might soon \n\ be blocked. The maximum value configured may be too low \n\ and you should consider increasing it. \n\ Or some of this client addresses are \n\ stale and you could clear them"

SISF-4-ENTRY_BLOCKED

4-Warning

Entry blocked [chars]

An attempt to install an entry in the IPv6 binding table was blocked. This can be due to a conflicting entry or maximum number of entries reached

sisf

"If the maximum table size is reached consider increasing it.\n\ If a conflicting entry already exist this maybe an attempt \n\ to steal address ownership. You should investigate which host\n\ is connected on the interface and wether it should be disconnected"

SISF-4-IP_THEFT

4-Warning

IP Theft [chars]

A duplicate IP address has been detected IP theft and blocked

sisf

"If the existing entry is REACHABLE in the binding table \n\ and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration \n\ issue that must be resolved"

SISF-4-MAC_THEFT

4-Warning

MAC Theft [chars]

A duplicate MAC address has been detected MAC theft and blocked

sisf

"If the existing entry is REACHABLE in the binding table \n\ and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration \n\ issue that must be resolved"

SISF-4-BT_TIMER

4-Warning

BT Timer [chars]

Configured timer value is out of range defined for \n Wireless SISF

sisf

"Configure BT stale lifetimer between 300 and 86400 seconds \n\ and for other timers between 1 - 86400 seconds"

SISF-4-MAC_AND_IP_THEFT

4-Warning

MAC_AND_IP Theft [chars]

A duplicate MAC and IP address has been detected MAC_AND_IP theft and blocked

sisf

"If the existing entry is REACHABLE in the binding table \n\ and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration \n\ issue that must be resolved"

SISF-4-PAK_DROP

4-Warning

Message dropped [chars]

A message was dropped because one of the IPv6 first-hop \n\ security features said so

sisf

"Look at the reason. It can either be a valid drop and that \n\ could go up to disconnect the host attached to the interface \n\ or the policy configured on this interface is too severed \n\ and should be amended"

SISF-4-DATA_GLEAN_NOTIF_RECEIVED

4-Warning

No binding for [chars]

A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table.

sisf

-

SISF-4-RESOLUTION_VETO

4-Warning

Resolution vetoed [chars]

-

ipv6

"A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests"

DC-4-FILE_OPEN_WARNING

4-Warning

Not able to open [chars]

The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles.

dc

" Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. "

DC-3-PATTERN_NOT_FOUND

3-Error

[chars]

The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reload the Device Pr/scratch/stevenl/polaris/wab_amur_eedge_polaris/novaofiles file to the flash and re-enable the device classifier"

DC-3-INCOMPATIBLE_PROFILE_VERSION

3-Error

Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec]

An incompatible profile version is detected. The device classifier feature will be operationally down.

dc

"Reload the expected version of device profiles file to the " "system and re-enable the device classifier "

DC-3-BUILTIN_INIT_FAIL

3-Error

[chars]

Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-6-DEFAULT_INIT_INFO

6-Information

[chars]

The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles.

dc

LOG_STD_ACTION

DC-3-SM_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Registraton of Device classifier with SM failed. So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-OUI_INIT_FAIL

3-Error

OUI Table initialization failed for [chars]

Loading of the OUI databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-CHECK_INIT_FAIL

3-Error

[chars]

Loading of the Checks databae in Device classifier failed.

dc

LOG_STD_ACTION

DC-3-DB_INIT_FAIL

3-Error

Device Classifier disabled. [chars] initialization failed

Initilization of Device classifier Internal database failed So the device classifier will be operationally down.

dc

LOG_STD_ACTION

DC-3-MAX_RULES_EXCEEDED

3-Error

[chars].

The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_PROFILES_EXCEEDED

3-Error

[chars].

The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-MAX_OUI_EXCEEDED

3-Error

[chars].

The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier"

DC-3-NO_MEM

3-Error

[chars].

There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles.

dc

"Increase the memory size in the system and " "re-enable the device classifier"

DC-3-DC_DISABLED

3-Error

[chars].

The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles

dc

"The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier"

DC-3-SM_UPDATE

3-Error

Failed to update [chars].

Internal error occured during device classification . This may cause the device to be unknown.

dc

-

DC-3-SM_API

3-Error

[chars] return [chars].

Internal error returned by Session Manager api.

dc

-

DC-3-FILE_READ_ERROR

3-Error

Error [chars] the profile file: [chars]

There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-FILE_CHECKSUM

3-Error

Checksum [chars] failed for the profile file: [chars]

Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier.

dc

-

DC-3-SM_GET

3-Error

Failed to get [chars].

Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results.

dc

-

DC-3-DISABLE_FAIL

3-Error

Failed to disable DC.

Internal error occured trying to disable Device Classifier.

dc

"Please run the command: show macro auto monitor clients and try disabling" "the clients"

DC-3-ENABLE_FAIL

3-Error

Failed to enable DC.

Internal error occured trying to enable Device Classifier.

dc

"Please check the previous DC error messages and take the relevant action"

DC-3-HRPC_SYNC

3-Error

Error on member switch [dec] error_code = [dec]

Internal error occured while trying to sync Device Classifier.state

dc

"Please check the state of the stack members"

KEYSTORE_AE46C1-6-SELF_TEST_PASS

6-Information

Keystore pass power on self test

keystore pass power on self test for both SHA1 and HMAC-SHA1

-

-

KEYSTORE_AE46C1-3-SELF_TEST_FAILURE

3-Error

Keystore power on self test failure. [chars]

keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state.

-

"Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced."

KEYSTORE_AE46C1-6-RANDOM

6-Information

A pseudo-random number was generated twice in succession[dec].

A pseudo-random number generator produced the same number twice\n\ in succession.

-

"Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative."

KEYSTORE-3-IFS_OPEN_W

3-Error

Failed to open file \[chars]\ for writing software keystore. [chars]

An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_WRITE

3-Error

An error occurred while writing to the software keystore file.

CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_OPEN_R

3-Error

Failed to open file \[chars]\ for reading software keystore. [chars]

An error occurred while opening the keystore file for reading. CTS keys could not be retrieved.

-

-

KEYSTORE-3-IFS_READ

3-Error

An error [chars] occurred while reading from the software

CTS keys could not be retrieved from persistent storage.

-

-

KEYSTORE-3-BAD_MAGIC

3-Error

Bad magic number 0x%08x in software keystore file \[chars]\.

Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-UNEXPECTED_EOF

3-Error

Unexpected end of file while reading software keystore \[chars]\.

Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-IPCPORT

3-Error

Failed to create IPC port [chars] for keystore redundancy. [chars].

An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCOPEN

3-Error

Failed to open IPC port to peer for keystore redundancy: [chars]

An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCNOCONN

3-Error

No IPC communication path to peer available for keystore [chars].

No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCSEND

3-Error

IPC send error [chars] while sending [chars].

An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-ISSU_INCOMPAT

3-Error

Standby incompatible for SSO.

The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode.

-

-

KEYSTORE-3-IPC_NO_PROC

3-Error

Could not create a process to receive keystore redundancy messages.

An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-NO_KEYSTORE

3-Error

CTS hardware keystore is not responsive and software emulation is not enabled.

The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore.

-

-

KEYSTORE-3-IFS_OPEN_W

3-Error

Failed to open file \[chars]\ for writing software keystore. [chars]

An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_WRITE

3-Error

An error occurred while writing to the software keystore file.

CTS keys could not be saved to persistent storage.

-

-

KEYSTORE-3-IFS_OPEN_R

3-Error

Failed to open file \[chars]\ for reading software keystore. [chars]

An error occurred while opening the keystore file for reading. CTS keys could not be retrieved.

-

-

KEYSTORE-3-IFS_READ

3-Error

An error [chars] occurred while reading from the software

CTS keys could not be retrieved from persistent storage.

-

-

KEYSTORE-3-BAD_MAGIC

3-Error

Bad magic number 0x%08x in software keystore file \[chars]\.

Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-UNEXPECTED_EOF

3-Error

Unexpected end of file while reading software keystore \[chars]\.

Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory.

-

-

KEYSTORE-3-IPCPORT

3-Error

Failed to create IPC port [chars] for keystore redundancy. [chars].

An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCOPEN

3-Error

Failed to open IPC port to peer for keystore redundancy: [chars]

An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCNOCONN

3-Error

No IPC communication path to peer available for keystore [chars].

No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-IPCSEND

3-Error

IPC send error [chars] while sending [chars].

An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-ISSU_INCOMPAT

3-Error

Standby incompatible for SSO.

The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode.

-

-

KEYSTORE-3-IPC_NO_PROC

3-Error

Could not create a process to receive keystore redundancy messages.

An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore.

-

-

KEYSTORE-3-NO_KEYSTORE

3-Error

CTS hardware keystore is not responsive and software emulation is not enabled.

The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore.

-

-

CTS-0-AUTHZ_OUT_OF_MEM

0-Emergency

[chars] failed to create [chars] due to insufficient memory

The system is experiencing insufficent memory.

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_CREATE_FAILED

3-Error

[chars] failed to create [chars]

An error occurred while CTS Authz attempts to create an internal data structure.

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_EXCEEDS_LIMIT

3-Error

[chars] encountered [chars][dec] exceeds max[dec]

Data exceeds maximum limits allowed.

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_UNINIT

3-Error

[chars] appears uninitialized

CTS Authz unexpectedly encountered an unitialized data

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_NULL

3-Error

[chars] encounters NULL [chars]

An unexpected NULL pointer/data is encountered.

-

LOG_STD_ACTION

CTS-3-AUTHZ_SYNC_FAILED

3-Error

Failed to send [chars] sync msg[chars] to Standby

An error occcured while CTS Authz is performing a sync to the Standby.

-

LOG_STD_ACTION

CTS-3-AUTHZ_FAILED_SYNC_RCV

3-Error

Standby failed receive sync msg[chars]

An error occcured while the Standby is receiving sync data from the Active.

-

LOG_STD_ACTION

CTS-3-AUTHZ_NOT_SUPPORTED

3-Error

[chars] encountered [chars] not unsupported

CTS encountered an unsupported data type or feature. This could be due to incompatibility

-

LOG_STD_ACTION

CTS-3-AUTHZ_DATA_FAILED

3-Error

[chars] failed to obtain [chars]

An error occurred while CTS Authz attempted to get/create a data structure

-

LOG_STD_ACTION

CTS-3-AUTHZ_INVALID_DATA

3-Error

[chars] encountered invalid [chars]

CTS Authz encountered an unexpected invalid data type.

-

LOG_STD_ACTION

CTS-3-AUTHZ_ADD_DATA_FAILED

3-Error

[chars] failed to add [chars] to [chars]

An error occurred while CTS Authz attempted to build its database.

-

LOG_STD_ACTION

CTS-3-AUTHZ_GENERIC_FAILURE

3-Error

[chars] [chars]

CTS Authz encountered internal error.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_WILDCARD_FAILED

3-Error

Failed to download default/unknown policy

An error occurred while CTS attempted to acquire wildcard policy from the ACS.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_PEER_DOWNLOAD_FAILED

3-Error

Failed to download peer policy for [chars]

An error occurred while CTS attempted to acquire peer policy from the policy server

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_SGACL_FAILED

3-Error

Failed to [chars][chars] SGACL [chars] for SGT=[chars]

An error occurred while CTS attempted to acquire SGACL policy from the policy server.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_SGACL_ACE_FAILED

3-Error

Failed to [chars][chars] SGACL '[chars]' for SGT=[chars] due to ACE '[chars]' error

An error occurred in the ACE while CTS attempted to acquire SGACL policy from the policy server.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_INGRESS_FAILED

3-Error

Failed to [chars] Ingress policy for [chars]

An error occurred while CTS attempted to acquire or install an Ingress policy from the ACS.

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_INTERNAL_FAILED

3-Error

Failed to acquire/install policy for [chars] due to internal error

An error occurred while CTS attempted to acquire/install a policy which may be caused by internal software error

-

LOG_STD_ACTION

CTS-3-AUTHZ_POLICY_FAIL_TO_REMOVE

3-Error

Failed to remove [chars] policy from the authorization dbase

An error occured while CTS attempted to remove the specified policy from its database. This could result in an action not being accomplished.

-

LOG_STD_ACTION

CTS-3-POLICY_COA_SGT_FAILED

3-Error

Failed to complete CoA request for update-sgt[chars]

An error occurred while CTS attempted to service a Change of Authorization request for the update-sgt command

-

LOG_STD_ACTION

CTS-3-POLICY_COA_RBACL_FAILED

3-Error

Failed to complete request for update-rbacl[chars]-[chars]

An error occurred while CTS attempted to service a Change of Authorization request for the update-rbacl command

-

LOG_STD_ACTION

CTS-6-POLICY_COA_SGT_REQUEST

6-Information

Command [chars]=[chars]

A Change of Authorization request command is received for update-sgt

-

LOG_STD_ACTION

CTS-6-POLICY_COA_RBACL_REQUEST

6-Information

Command [chars]=[chars]-[chars]

A Change of Authorization request command is received for update-rbacl

-

LOG_STD_ACTION

CTS-6-POLICY_COA_DONE

6-Information

Command [chars]=[chars] completed

A Change of Authorization request has been serviced

-

LOG_STD_ACTION

CTS-6-POLICY_COA_NO_ACTION

6-Information

Command [chars]=[chars] has no change

A Change of Authorization request has been received but no action was taken due to the system is already in possession of the requested data

-

LOG_STD_ACTION

CTS-6-POLICY_COA_NO_SESSION

6-Information

Command [chars]=[chars] has no session associated

A Change of Authorization request has been received for infomration that the system is not in possession of

-

LOG_STD_ACTION

CTS-6-POLICY_RBACL_MONITOR_ALL

6-Information

Failed to set monitor all for dynamic policies

An error occurred while CTS attempted to set monitor flag for all dynamic installed policies.

-

LOG_STD_ACTION

CTS-3-POLICY_HA_PROC_FAIL

3-Error

Error starting up HA switchover Policy refresh process.

A failure has occurred in switchover which has prevented the policy refresh process to be lauched. User should manually refresh policies via the \cts refresh policy\ commad

-

"Issue command \"cts refresh policy\" and verify policy timers" " are active If timers do not start "LOG_STD_ACTION

CTS-6-REAUTH_TIMER_EXPIRED

6-Information

Timer expired on int[chars]

REAUTH Timer expired

-

LOG_STD_NO_ACTION

CTS-6-AUTHZ_REFRESH_EXPIRY

6-Information

Policy refresh timer[dec] secs has expired for peer[chars]

-

-

-

CTS-3-AUTHZ_CACHE_OPEN_FAIL

3-Error

[chars] failed to open cache file[chars] for read

CTS Cache read: Failed to open cache file for read

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_READ_FAIL

3-Error

[chars] failed to read from cache file[chars]

CTS Cache: Failed to read from cache file

-

LOG_STD_ACTION

CTS-6-AUTHZ_CACHE_READ_RESULT

6-Information

[chars] cache read from file[chars] [chars]

CTS Cache read from cache file done

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHED_DATA_READ_FAIL

3-Error

[chars] failed to read cached data

CTS Cache: Failed to read cached data

-

LOG_STD_ACTION

CTS-6-AUTHZ_CACHED_DATA_EXPIRED

6-Information

[chars] cached data expired

CTS Cache: Cached data expired

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_OPEN_WRITE_FAIL

3-Error

[chars] failed to open cache file[chars] for write

CTS Cache: Failed to open cache file for write

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_SRV_WRITE_FAIL

3-Error

[chars] failed to write server list to cache file[chars]

CTS Cache: Failed to write server list to cache file

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_MSGT_WRITE_FAIL

3-Error

[chars] failed to write Multicast SGT Table to cache file[chars]

CTS Cache: Failed to write Multicast SGT Table to cache file

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_SGT_WRITE_FAIL

3-Error

[chars] failed to write SGT SG Name Table to cache file[chars]

CTS Cache: Failed to write SGT SG Name Table to cache file

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_PEER_POL_WRITE_FAIL

3-Error

Failed to write peer policy to cache

CTS Authz Cache: Failed to write peer policy to cache

-

LOG_STD_ACTION

CTS-3-AUTHZ_CACHE_SGT_POL_WRITE_FAIL

3-Error

Failed to write SGT policy to cache

CTS Authz Cache: Failed to write SGT policy to cache

-

LOG_STD_ACTION

CTS-3-AAA_NO_CONTEXT

3-Error

Failed to retrieve AAA context to construct AAA attribute for RADIUS request

CTS AAA Request Add : Failed to retrieve AAA context to construct AAA attribute for RADIUS request

-

LOG_STD_ACTION

CTS-3-AAA_NO_RADIUS_SERVER

3-Error

No RADIUS servers available for CTS AAA request for [chars]

CTS AAA Request Setup : No RADIUS servers available for CTS AAA

-

LOG_STD_ACTION

CTS-3-AUTHZ_SM_FAILED

3-Error

Failed to start the authorization entry state machine to start policy acquisition for peer[chars]

-

-

-

CTS-3-AUTHZ_TREE_MAP_INSERT_FAILED

3-Error

Failed to insert the authz entry info into tree map for peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_UPDATED

6-Information

Policy update received for old SGT [chars] new SGT[chars]

-

-

-

CTS-6-AUTHZ_ENTRY_ACCESS_POLICY_STATE

6-Information

Policy Acquisition in ACCESS state for peer[chars] sgt[chars]

-

-

-

CTS-6-AUTHZ_ENTRY_COMPLETE_STATE

6-Information

Policy Acquisition in COMPLETE state for peer[chars] sgt[chars]

-

-

-

CTS-5-POLICY_ACQUISITION_SUCCESS

5-Notice

Policy Acquisition success for peer[chars] sgt[chars]

-

-

-

CTS-7-AUTHZ_ENTRY_HDL_SENDL_FAILED

7-Debug

Error retrieving the authorization entry handle

Error retrieving the authorization entry handle

-

LOG_STD_ACTION

CTS-7-AUTHZ_ENTRY_PENDING_REQUEST

7-Debug

RADIUS request to acquire policy for peer[chars] sgt[chars] was not

RADIUS request to acquire policy for peer was not sent due to pending request in progress

-

LOG_STD_ACTION

CTS-7-AUTHZ_ENTRY_WAIT_FOR_ACE

7-Debug

Policy Acquisition for peer[chars] sgt[chars] is waiting for the

Policy acquisition for peer is waiting for the ACE download complete

-

LOG_STD_ACTION

CTS-3-AUTHZ_ENTRY_RADIUS_FAILED

3-Error

Policy Acquisition failed to transmit RADIUS request for peer[chars] sgt[chars]

-

-

-

CTS-7-AUTHZ_PEER_POL_DEL

7-Debug

Deleting peer policy for peer[chars] sgt[chars]

-

-

-

CTS-7-AUTHZ_PEER_POL_DEL_PENDING

7-Debug

Pending peer policy delete for peer[chars] sgt[chars] due to

Pending peer policy delete for peer due to outstanding SGACL install/uninstall

-

LOG_STD_ACTION

CTS-3-AUTHZ_UNINST_SESSION_FR_NAMELIST_FAILED

3-Error

Failed to locate named list to uninstall session

Failed to locate named list to uninstall session

-

LOG_STD_ACTION

CTS-3-AUTHZ_SESSION_UNINST_SGACL_FAILED

3-Error

Failed to detach session handle from SGACL list for sgt[chars]

-

-

-

CTS-3-AUTHZ_SESSION_SM_START_FAILED

3-Error

Failed to initialize the environment-data module

Failed to initialize the environment-data module

-

LOG_STD_ACTION

CTS-3-ENV_DATA_INIT_FAILED

3-Error

Failed to initialize and start the authorization state machine

Failed to initialize and start the authorization state machine

-

LOG_STD_ACTION

CTS-6-AUTHZ_POLICY_SGACL_ATTACH_SUCCESS

6-Information

Successfully attached RBM SGACL to RBM policy for sgt[chars]:[chars]

-

-

-

CTS-6-AUTHZ_POLICY_SGACL_SUCCESS

6-Information

Successfully [chars] SGACL for sgt[chars]

-

-

-

CTS-6-AUTHZ_POLICY_SGACL_UPDATE

6-Information

SGACL[chars]gen-id[chars] updated to SGACL[chars]gen-id[chars]

-

-

-

CTS-6-AUTHZ_POLICY_SGACL_NO_CHANGE

6-Information

Policy refresh for sgt[chars] indicates no change

-

-

-

CTS-6-AUTHZ_WAIT_POLICY_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_INSTALL_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_WAIT_FOR_RBM_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_INSTALL_SUCCESS

6-Information

Policy Installation success for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_NO_OP

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_POLICY_UNINSTALL_SUCCESS_STATE

6-Information

Policy Installation in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_RETRY_INSTALL

6-Information

Policy Installation retry install for int[chars] peer[chars] flag[hec]

-

-

-

CTS-6-AUTHZ_SM_INIT

6-Information

Policy Installation state machine initializing in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_DESTROY

6-Information

Policy Installation state machine destroyed in [chars] state for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_STOP

6-Information

Policy Installation state machine stopped for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_RUN

6-Information

Policy Installation state machine running for int[chars] peer[chars]

-

-

-

CTS-6-AUTHZ_SM_REINIT

6-Information

Policy Installation state machine reinitialization for int[chars] peer[chars]

-

-

-

CTS-6-ENV_DATA_REFRESH_TIMER

6-Information

Time to refresh environment data

ENV data refresh timer

-

LOG_STD_NO_ACTION

CTS-3-ENV_DATA_ERROR

3-Error

Environment data error in [chars] state

ENV data error

-

LOG_STD_NO_ACTION

CTS-4-SLIST_HANDLER_FAILED

4-Warning

[chars]:tag[chars] - failed to locate server list handle.

-

-

-

CTS-4-SLIST_ADD_TO_PREFERRED_LIST_FAILED

4-Warning

[chars]:tag[chars] - failed to add server[inet]:[dec] to preferred list.

-

-

-

CTS-4-SLIST_ADD_TO_NAMED_LIST_FAILED

4-Warning

[chars]:tag[chars] - failed to add server[inet]:[dec] to named list.

-

-

-

CTS-4-SLIST_INVALID_LIST_TYPE

4-Warning

[chars]:tag[chars] - invalid server list type[dec].

-

-

-

CTS-4-CREATE_SLIST_FAILED

4-Warning

[chars]: Failed to create server list.

CTS HA failed to create server list while processing server named list sync message.

CTS_DDTS_COMPONENT

LOG_STD_ACTION

CTS-6-ENV_DATA_START_STATE

6-Information

Environment Data Download in start state

Environment data download in start state

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-ENV_DATA_WAIT_RESP_STATE

6-Information

Environment Data Download in wait response state

Environment data download in wait response state

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-6-ENV_DATA_ASSESS_STATE

6-Information

Environment Data Download in assess state

Environment data download in assess state

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-ENV_DATA_ACQUISITION_SUCCESS

5-Notice

Environment data download success

Environment data download completed

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-5-ENV_DATA_INSTALL_SUCCESS

5-Notice

Environment data installation success

Environment data installation completed

CTS_DDTS_COMPONENT

LOG_STD_NO_ACTION

CTS-3-ROOT_CA_STORE_FAIL

3-Error

Could not install the CTS trusted-root certificate.

An error occcured while installing the CTS trusted-root certificate. This means that CTS cannot validate AAA servers' certifcates received during EAP-FAST exchanges.

-

-

CTS-5-ROOT_CA_STORE_DONE

5-Notice

A trusted-root certificate to be used for CTS has been installed.

A CTS trusted-root certificate was received from a AAA server during an EAP-FAST enrollment. This certificate will be used for validating all AAA servers' certificates received from here on.

-

-

CTS-3-LSC_STORE_FAIL

3-Error

Failed to install newly-provisioned locally-significant certificate.

An error occurred while installing our locally significant certificate to be used for CTS. This means that we cannot be authenticated using a certificate. If a CTS password is available we will continue to authenticate using the password.

-

-

CTS-3-LSC_CA_STORE_FAIL

3-Error

Failed to install certificate of CA that issued our locally-significant certificate

An error occurred while installing the certificate of our issuing CA. When this error occurs the locally-significant certificate will be discarded and CTS will continue to use its password credentials for authentication.

-

-

CTS-3-LSC_ENROLL_FAIL

3-Error

Failed to set re-enrollment attributes for CTS locally-significant certificate.

An error occurred while setting the re-enrollment attributes for the new CTS certificate. When this error occurs the new certificate will be discarded and CTS will continue to use its password credentials for authentication.

-

-

CTS-5-PASSWORD_CHANGE_ONE

5-Notice

CTS password in the keystore has been renamed \[chars]\.

An MSCHAPv2 change-password sequence has been successfully executed and the old password is being renamed for fallback use. This is the first of a 2-part operation. Next the new password will be renamed to become the active password.

-

-

CTS-5-PASSWORD_CHANGE_TWO

5-Notice

A new CTS password has been installed as \[chars]\ in the keystore.

A new CTS password has been installed in the keystore following a successful MSCHAPv2 change-password sequence. The old password has been saved for fallback use.

-

-

CTS-4-NO_PROV_SECRET

4-Warning

No shared secret available for provisioning PAC from server [inet].

We are unable to provision or reprovision a CTS PAC because we do not have a configured RADIUS shared secret for the server and there are no valid unexpired PACs that can be used to secure the re-provisioning exchange.

-

-

CTS-1-CTS_CRED_ACTION_NEEDED

1-Alert

CTS credentials are missing or inconsistent in the redundant keystore.\n Please re-configure cts credentials or execute cts change-password.

A redundant keystore was detected as either not containing any CTS credentials or having a different set of credentials as contained in the active keystore. This means that CTS authentication will fail upon switchover unless remedial action is taken before then. Either use the \cts credentials ...\ CLI to re-configure the CTS device-id and password or use the \cts change-password ...\ CLI to initiate a password change with the AAA server. Either of these actions will cause the device-id and password to be inserted in both the active and redundant keystores.

-

-

CTS-6-PAC_PROVI_SUCCESS

6-Information

PAC Provisioning succeeded for [inet] A-ID=[chars]

PAC Provisioning succeeded

-

LOG_STD_NO_ACTION

CTS-3-PAC_PROVI_FAIL

3-Error

PAC Provisioning failed for [inet]

PAC Provisioning failed

-

LOG_STD_ACTION

CGC-0-CGC_EMERG

0-Emergency

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-1-CGC_ALERT

1-Alert

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-2-CGC_CRIT

2-Critical

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-3-CGC_ERR

3-Error

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-4-CGC_WARNING

4-Warning

[chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-5-CGC_NOTICE

5-Notice

[chars]

Normal but significant conditions

CGC_DDTS_COMPONENT

LOG_STD_ACTION

CGC-6-CGC_INFO

6-Information

[chars]

Informational messages

CGC_DDTS_COMPONENT

LOG_STD_NO_ACTION

CGC-7-CGC_ASSERT

7-Debug

Assertion Failure [chars] @[chars]:[dec] : [chars]

CGC_INTERNAL_ERROR

CGC_DDTS_COMPONENT

LOG_STD_ACTION

EPM-6-POLICY_REQ

6-Information

IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars]

This message indicates that a policy application/remove request has been\n\ received by the EPM

pem

"No action required"

EPM-6-POLICY_APP_SUCCESS

6-Information

Policy Application succeded for Client [[chars]] MAC [[enet]] AuditSession ID [[chars]] for POLICY_TYPE [[chars]] POLICY_NAME [[chars]]

This message indicates that the displayed policy for the client has been\n\ applied successfully by the EPM

pem

"No action required"

EPM-4-POLICY_APP_FAILURE

4-Warning

Policy Application Failed for Client [[chars]] MAC [[enet]] AuditSessionID [[chars]] for POLICY_TYPE [chars] POLICY_NAME [chars] REASON [chars]

This message indicates that the displayed policy for the client\n\ could not be applied by the EPM

pem

"Policy application failure could happen due to multiple reasons.The \n\ reason for the failure is notified to the client and the client has to\n\ take appropriate action based on it"

EPM-6-AAA

6-Information

POLICY [chars]| EVENT [chars]

This message indicates a download request has been sent/downloaded\n\ successfully for the specified dACL

pem

"No action required"

EPM-6-ACL_CONFIG_ERROR

6-Information

ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]'

This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration

pem

"Change ACE configuration for the specifed ACL"

EPM-6-IPEVENT

6-Information

IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars]

This message indicates the IP event Wait/Release/Assignment that\n\ has occured with respect to the specified host

pem

"No action required"

EPM-6-AUTH_ACL

6-Information

POLICY [chars]| EVENT [chars]

This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed

pem

"No action required"

SSFPD-6-UPGRADE_COMPLETE

6-Information

Upgrade for Smart SFP in bay [dec] port [dec] complete

Smart SFP upgrade complete notification. This is not a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-6-UPGRADE_STARTED

6-Information

Upgrade started for Smart SFP in bay [dec] port [dec]

Smart SFP upgrade start notification. This is not a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-3-UPGRADE_FAILED

3-Error

Upgrade failed for Smart SFP in bay [dec] port [dec]

Smart SFP upgrade fail notification. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-3-CN_NOT_MANAGEABLE

3-Error

Upgrade failed for Smart SFP in bay [dec] port [dec] CN not manageable

Smart SFP upgrade fail notification. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-3-BACKWARD_INCOMPATIBLE

3-Error

Upgrade failed for Smart SFP in bay [dec] port [dec] PP backward incompatible with Titan

Smart SFP upgrade fail notification. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-6-NO_CONTENT_CHANGE

6-Information

Skipping upgrade for for Smart SFP in bay [dec] port [dec] Smart SFP already running same version

Smart SFP upgrade fail notification. This is a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-6-NOT_DISCOVERED

6-Information

Skipping upgrade for Smart SFP in bay [dec] port [dec] discovery incomplete

Smart SFP upgrade fail notification. This could be a software/Hardware error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-6-UPGRADE_REQUIRED

6-Information

PP version Upgrade required for Smart SFP in bay [dec] port [dec]. Use 'upgrade hw-programmable ssfp slot <logical-slot> bay <bay-number> port <port-number>' cli for upgrade

Smart SFP upgrade fail notification. This is not a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-6-UPGRADE_IN_PROGRESS

6-Information

Skipping upgrade for for Smart SFP in bay [dec] port [dec] Smart SFP upgrade already in progress

Smart SFP upgrade fail notification. This is not a software error.

-

LOG_STD_SH_TECH_ACTION

SSFPD-6-SKIP_VCOP_SW_VER_CMD

6-Information

Skipping CLI command as smart SFP upgrade already in progress Retry once upgrade completed

Skipping SFP software version command during upradation. This is not a software error.

-

LOG_STD_SH_TECH_ACTION

BCM_INIT-3-BCM_KBP_INIT_APPL_FAIL

3-Error

KBP Application INIT Failure on asic [dec]

KBP appl initialation failed during the BCM init

rsp3-infra

"Please collect nile mgr and uea mgr pman logs" "from shell"

BCM_INIT-3-BCM_KBP_INIT_ILKN_FAIL

3-Error

KBP ILKN INIT Failure on asic [dec]

KBP ilkn initialation failed during the BCM init

rsp3-infra

"Please collect nile mgr and uea mgr pman logs" "from shell"

UEA_IDMGR-3-RESERVE_FAIL

3-Error

IDMGR ID [chars] Failure func [chars] line [dec] Feat [dec] ID [dec]

IDMGR API failed

rsp3-infra

"Please fix it"

CEF-3-KBP_PREFIX_IP_MPLS_LIMIT_EXCEEDED

3-Error

Number of ip mpls Prefixes exceeded allowed limit [dec] on asic [dec]

Number of ip mpls Prefixes exceeded supported scale

rsp3-infra

"Please reduce the number of ip mpls Prefixes" "to scale to platform supported scale"

CEF-3-KBP_PREFIX_IPV6_LIMIT_EXCEEDED

3-Error

Number of ipv6 Prefixes exceeded allowed limit [dec] on asic [dec]

Number of ipv6 Prefixes exceeded supported scale

rsp3-infra

"Please reduce the number of ipv6 Prefixes" "to scale to platform supported scale"

MPLS-3-VPLS_PORT_LEARNING_ENABLE

3-Error

Port Learning enable issue on port [chars]

Learning set/unset in port and default lif

rsp3-mpls

"Please enable/disable mpls ip on port"

MPLS-3-VPLS_PORT_DEFAULT_LIF_LEARNING_ENABLE

3-Error

Default lif learning enable issue on lif 0x[hec] intf [chars]

Learning set/unset in port and default lif

rsp3-mpls

"Please enable/disable mpls ip "

ENVIRONMENTAL-3-ALERT

3-Error

Critical limit reached for PVT temperature sensor on Asic: [dec] Reading: [dec] Celsius

Informational message for relating to Asic PVT sensor value

asr900-system-rsp3

"No action required"

BCM_INIT-3-BCM_KBP_INIT_APPL_FAIL

3-Error

KBP Application INIT Failure on asic [dec]

KBP appl initialation failed during the BCM init

dominica-infra

"Please collect uea mgr pman logs from shell"

BCM_INIT-3-BCM_KBP_INIT_ILKN_FAIL

3-Error

KBP ILKN INIT Failure on asic [dec]

KBP ilkn initialation failed during the BCM init

dominica-infra

"Please collect uea mgr pman logs from shell"

UEA_IDMGR-3-RESERVE_FAIL

3-Error

IDMGR ID [chars] Failure func [chars] line [dec] Feat [dec] ID [dec]

IDMGR API failed

dominica-infra

"Please fix it"

CEF-3-KBP_PREFIX_IP_MPLS_LIMIT_EXCEEDED

3-Error

Number of ip mpls Prefixes exceeded allowed limit [dec] on asic [dec]

Number of ip mpls Prefixes exceeded supported scale

dominica-infra

"Please reduce the number of ip mpls Prefixes" "to scale to platform supported scale"

CEF-3-KBP_PREFIX_IPV6_LIMIT_EXCEEDED

3-Error

Number of ipv6 Prefixes exceeded allowed limit [dec] on asic [dec]

Number of ipv6 Prefixes exceeded supported scale

dominica-infra

"Please reduce the number of ipv6 Prefixes" "to scale to platform supported scale"

MPLS-3-VPLS_PORT_LEARNING_ENABLE

3-Error

Port Learning enable issue on port [chars]

Learning set/unset in port and default lif

dominica-mpls

"Please enable/disable mpls ip on port"

MPLS-3-VPLS_PORT_DEFAULT_LIF_LEARNING_ENABLE

3-Error

Default lif learning enable issue on lif 0x[hec] intf [chars]

Learning set/unset in port and default lif

dominica-mpls

"Please enable/disable mpls ip "

BCM_BFD-3-BCM_BFD_CREATE_FAIL

3-Error

BFD endpoint create failed for ld [dec] on asic [dec]

BCM BFD endpoint create failed

rsp3-bfd

"Please collect nile mgr and uea mgr pman logs" "from shell"

BCM_BFD-3-BCM_BFD_DELETE_FAIL

3-Error

BFD endpoint create failed for ld [dec] on asic [dec]

BCM BFD endpoint delete failed

rsp3-bfd

"Please collect nile mgr and uea mgr pman logs" "from shell"

BCM_TRAPS-2-BCM_SNOOP_CREATE_FAIL

2-Critical

Snoop command create failed for cpuq [dec]

BCM Snoop command create failed

rsp3-traps

"Please collect nile mgr and uea mgr pman logs" "from shell"

BCM_BFD-3-BCM_BFD_CREATE_FAIL

3-Error

BFD endpoint create failed for ld [dec] on asic [dec]

BCM BFD endpoint create failed

rsp3-bfd

"Please collect nile mgr and uea mgr pman logs" "from shell"

BCM_BFD-3-BCM_BFD_DELETE_FAIL

3-Error

BFD endpoint create failed for ld [dec] on asic [dec]

BCM BFD endpoint delete failed

rsp3-bfd

"Please collect nile mgr and uea mgr pman logs" "from shell"

BCM_TRAPS-2-BCM_SNOOP_CREATE_FAIL

2-Critical

Snoop command create failed for cpuq [dec]

BCM Snoop command create failed

rsp3-traps

"Please collect nile mgr and uea mgr pman logs" "from shell"

RMGR-3-OUT_OF_TCAM_IPV4_ROUTE

3-Error

Out of tcam resources to execute command

Number of IPv4 routes installed exceeded supported scale

asr903-cfc

"Please reduce the number of IPv4 routes configured " "to supported scale. Clear the table to successfully" " reinstall all entries"

RMGR-3-OUT_OF_TCAM_IPV6_ROUTE

3-Error

Out of tcam resources to execute command

Number of IPv6 routes installed exceeded supported scale

asr903-cfc

"Please reduce the number of IPv6 routes configured " "to supported scale. Clear the table to successfully" " reinstall all entries"

MCASTV4-3-OUT_OF_TCAM_IPV4_MCAST

3-Error

Out of tcam space

Number of IPv4 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 mcast routes " "configured to supported scale"

MCASTV6-3-OUT_OF_TCAM_IPV6_MCAST

3-Error

Out of tcam space

Number of IPv6 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv6 mcast routes " "configured to supported scale"

MPLS-3-OUT_OF_LABEL3_SPACE

3-Error

Out of resource to create labels

Number of empls 3d labels exceeded supported scale

rsp2-mpls

"Please reduce the number of empls 3d labels to " "supported scale"

MPLS-3-OUT_OF_LABEL_SPACE

3-Error

Out of resource to create labels

Number of empls intd labels exceeded supported scale

rsp2-mpls

"Please reduce the number of empls intd labels to " "supported scale"

MPLS-3-MAX_PW_EXCEEDED

3-Error

Number of PW's exceeded supported limit [dec]

Number of PW's exceeded supported scale

rsp2-mpls

"Please reduce the number of PW's to supported scale"

MPLS-3-MAX_ROUTED_PW_EXCEEDED

3-Error

Number of Routed PW's exceeded supported limit [dec]

Number of Routed PW's exceeded supported scale

rsp2-mpls

"Please reduce the number of " "Routed PW's to supported scale"

MPLS-3-MPLS_MTU_ALLOC_FAIL

3-Error

Out of resource to allocate mpls mtu

mpls mtu exceeded supported scale

asr903-mpls

"Please reduce the number of mpls mtu configured values" "to supported scale"

MPLS-3-FRR_BDI_UNSUPPORTED

3-Error

FRR not enabled on [chars]. Unsupported EFP and trunk EFP count [dec]. Supported 1

LFA FRR support on ASR903 for BDI interface is available with just one EFP or trunk EFP

asr903-mpls

"shutdown the BDI interface. Remove all the " " EFPs/TEFPs under the BDI. Create just one EFP or TEFP." " no shutdown the BDI interface"

MPLS-3-MPLS_STALE_LABEL

3-Error

Stale Label : [dec] Neither Allocated nor Deallocated

Stale Label Neither Allocated nor Deallocated

rsp2-mpls

"Don't collect the stats for this instance"

CEF-3-CYLON_CEF_MAX_VRF_EXCEEDED

3-Error

Number of VRF instances already exceeded allowed limit [dec]

Number of vrf instances exceeded supported platform scale

firmware

"Please reduce the number of vrf instances" "to scale to platform supported scale"

QOSMGR-3-ASIC_PROGRAMMING_FAIL

3-Error

Fails to program the ASIC for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_PROGRAMMING_FAIL

3-Error

Fails to program TCAM for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_EXHAUSTION

3-Error

Internal Error in resource allocation

The system is running out of TCAM entries to support the number of traffic classes in the policy-map. The maximum number of TCAM entries is platform dependent.

firmware

"Reduce the number of classes in attached policy-maps"

QOSMGR-3-LABEL_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of QoS label to support the number of traffic classes in all attached policy-maps.

firmware

"Reduce the number of distinctive class-maps matches " "or 'set' actions in attached policy-maps"

QOSMGR-3-TABLEMAP_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of table-map resources

-

"Reduce the number of distinctive class-map " "matches in attached policy-maps"

QOSMGR-4-STATISTICS_FAIL

4-Warning

Internal Error in reading statistics

Can not access to HW to read statistics successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TDM_OC_HIERARCHY_UNSUPPORTED

3-Error

Only two-level hierarchy is supported on TDM/OC3/OC12 interfaces

Unsupported QoS hierarchy on TDM/OC3/OC12 interfaces

firmware

"Change config to reduce to two-level policy"

QOSMGR-3-POLICER_PROGRAMMING_FAIL

3-Error

Fails to program HW policer

Can not access to HW successfully.

firmware

""

QOSMGR-4-POLICER_EXCEEDING_HW

4-Warning

Policer configuration has exceeded hardware limitation for policymap [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-3-L4OP_ACL_PORT_CONFLICT

3-Error

Port ranger is already allocated to ACL on this interface.\n QoS policy configruation failed. Remove QoS command from interface[chars]

ACL configured on this interface uses Port ranger. Remove ACL configuration apply QoS first and then configure ACL

firmware

"Remove ACL configured on interface."

QOSMGR-3-L4OP_QOS_PORT_CONFLICT

3-Error

Port ranger is allocated to QOS on this interface port expansion used for configured ACL [chars]

IPv6 QOS configured on this interface uses Port ranger

firmware

"Remove IPv6 QOS configured on interface."

QOSMGR-3-L4OP_PORT_RANGE_VCU_PER_PORT_EXCEEDED

3-Error

Port range entry on this interface has exceeded maximum permitted 8 operations further l4 match ACE will be ignored[chars]

Interface already has maximum permitted 8 l4 operations

firmware

"Configure only 8 l4 match ACE per interface"

QOSMGR-3-L4OP_ACL_RESERVATION_EXHAUSTED

3-Error

Port ranger resource reserved for ACL exhausted port expansion used [chars]

Port ranger is shared between ACL and v6 QOS ACL. ACL reservation exhausted

firmware

"Remove ACL configuration or increase reservation through ROMMON variable" " QOS_PORTRANGE_RESOURCE"

QOSMGR-3-L4OP_QOS_RESERVATION_EXHAUSTED

3-Error

Port ranger resource reserved for QOS exhausted. policy configuration failed \nRemove other IPv6 QOS configuration or increase reservation through ROMMON [chars]

Port ranger is shared between ACL and v6 QOS ACL. QOS reservation exhausted

firmware

"Remove other IPv6 QOS ACL configuration or increase reservation through ROMMON" " QOS_PORTRANGE_RESOURCE"

QOSMGR-4-EGG_AGG_POLICER_EXCEEDING_HW

4-Warning

Output Parent policer block size can't be allocated configuration has exceeded hardware limitation for policymap [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-4-EGG_AGG_POL_BLOCK_EXCEEDING_HW

4-Warning

Number of output child policer's are more than the block size. Configure the block size accordingly [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-3-INGRESS_QOS_HANDLE_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-handle to support specified policy-map.

firmware

""

QOSMGR-3-INGRESS_QOS_PROFILED_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-profiled to support the specified policy-map.

firmware

""

QOSMGR-3-SCHEDULER_PROGRAMMING_FAIL

3-Error

Fails to program HW scheduler

Can not access to HW successfully.

firmware

""

QOSMGR-4-QUEUE_EXCEEDING_HW

4-Warning

Queue configuration has exceeded hardware limitation for policymap [chars]

The system is running out of output queues to support the specified policy-map.

firmware

"Reduce the number of the traffic classes in attached output policy-maps."

QOSMGR-4-INVALID_POLICYMAP_DUE_NON_QOS_EVENT

4-Warning

The policy-map [chars] is detached due to the event [chars].

The attached policy-map becomes invalid due to the change of the port speed.

firmware

"Change the shaping/bandwidth of the output policy-map and re-attach to the interface ."

QOSMGR-3-OUT_OF_TCAM_RESOURCES

3-Error

Out of tcam resources to execute command

Lack of tcam resources due to higher tcam resource requirements

firmware

"Change config to reduce tcam entry usage"

QOSMGR-3-PROFILES_EXHAUSTED

3-Error

Out of rm profiles to execute command

No free RM profile to accommodate the request

firmware

"Change config to reduce or reuse RM profiles"

QOSMGR-3-QUEUE_FLUSH_FAILED

3-Error

Queue-Flush not successful

Scheduler unable to flush the queue

firmware

"Remove any shape configuration for the queue"

QOSMGR-3-MAX_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum queue-limit commands per class

Trying to exceed the maximum queue-limit commands allowed per class

firmware

"Try reducing queue-limit commands under the class"

QOSMGR-3-MAX_QUALIFIED_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum qualified queue-limit commands per class

Trying to exceed the maximum qualified queue-limit commands allowed per class

firmware

"Try reducing qualified queue-limit commands " "under the class"

QOSMGR-3-UNSUPPORTED_QLIMIT_UNITS

3-Error

Qlimit unit other than usec & byte is not supported

Trying to configure a qlimit unit other than bytes or usec

firmware

"Configure qlimit in terms of bytes or usec"

QOSMGR-3-QLIMIT_VALUE_OUT_OF_RANGE

3-Error

Qlimit value is out of range

Trying to configure a qlimit value outside the supported range

firmware

"Configure qlimit value within supported range"

QOSMGR-3-QLIMIT_LEVEL_ERROR

3-Error

Qlimit command not supported in non-leaf classes

Trying to configure qlimit in a non leaf class

firmware

"Configure qlimit only in leaf classes"

QOSMGR-3-MANUAL_SHAPE_EXCEEDS_SPEED

3-Error

Invalid policy-map detected during interface speed change

Shape value in policy exceeds port speed

firmware

"Configure lesser shape value which will not " "exceed interface speed"

QOSMGR-3-BANDWIDTH_OVERSUBSCRIBED

3-Error

Bandwidth oversubscribed in the interface

Sum of committed bandwidth at a particular level exceeds the sum total of interface's max bandwidth

firmware

"Reduce the committed bandwidth to be less that " "interface's max bandwidth"

QOSMGR-3-SHAPE_UNDERFLOW

3-Error

New shape/speed value is less than the total bandwidth configured in the interface

Shape/speed configured is less than the total bandwidth configured in the interface

firmware

"Increase the shape/speed value or reduce " "the bandwidth configured in the child classes"

QOSMGR-3-BANDWIDTH_LEVEL_ERROR

3-Error

Bandwidth command not acceptable at interface level

Hardware does not support bandwidth at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-PRIORITY_LEVEL_ERROR

3-Error

Priority command not acceptable at interface level

Hardware does not support priority at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-BANDWIDTH_SHAPE_ERROR

3-Error

Bandwidth configured is greater than shapePIR of the class

Bandwidth should not be greater than shape value

firmware

"Reduce the bandwidth value to less than" " class's shapePIR value"

QOSMGR-3-BANDWIDTH_PARENT_SHAPE_ERROR

3-Error

Sum of bandwidths is greater than parent class's shapePIR

Total bandwidth of the classes at the same level exceeds the parent class's shapePIR value

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_PARENT_ERROR

3-Error

Sum of bandwidths is greater than parent class's bandwidth

Total bandwidth of the classes at the same level exceeds the parent class's bandwidth

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_CHILD_ERROR

3-Error

Bandwidth in one of the children class is greater than input bandwidth

Children class's bandwidth should not be greater

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-PROFILE_EXHAUST

3-Error

No free scheduler profiles available in hardware

With the new configuration there is no free profile available in the HW this could be because of dissimilar profiles configured at the same hierarchy level

firmware

"Change the config value to closest existing config"

QOSMGR-3-EFP_SHAPE_RESTRICTION

3-Error

EFP policies cannot have shape command at physical level and more than one logical level classes

Since the HW does not support four level hierarchy EFP policies sit in pseudo level between Physical and Logical level

firmware

"Either remove vlan hierarchy in the EFP policy or" " do not configure shape command at physical level"

QOSMGR-3-SHAPE_PARENT_ERROR

3-Error

Shape value is greater than parent class's shape or interface's speed

Parent class's shape value cannot be smaller than current

firmware

"Configure shape value lesser than parent class's" " shape or interface's speed"

QOSMGR-3-SHAPE_CHILD_ERROR

3-Error

One of children class's shape config is higher

Children class's shape should not be higher than current

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_CHILD_BANDWIDTH_ERROR

3-Error

Bandwidth in one of the children class is greater than input shape value

Children class's bandwidth should not be higher than input

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_BANDWIDTH_PERCENT_ERROR

3-Error

Shape - Bandwidth-percent values inconsistent in the hierarchy calculated bandwidth will exceed shape

Because of this new shape command Bandwidth percent configured in one of children class will get more value than its manually configured shape. Please note that bandwidth percent is calculated from parent's shapePIR

firmware

"Either configure higher shape value or " " reduce violating bandwidth-percent value"

QOSMGR-3-LOGICAL_RESOURCE_EXHAUSTED

3-Error

Logical level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused logical level classes"

QOSMGR-3-QUEUE_EXHAUSTED

3-Error

Class level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused class level classes"

QOSMGR-3-EQOS_CXT_EXCEEDED

3-Error

Maximum Egress QosContexts consumed in the Bridge-Domain

Number of Egress QoS vlan matches exceeds the maximum allowed in the Bridge-Domain

firmware

"Reduce the number of Egress QoS vlan" " matches in the Bridge-Domain and try again"

QOSMGR-3-PROTOCOL_NOT_SUPPORTED_FOR_POLICY

3-Error

The configured protocol is not supported in QoS policy

Configured protocol is not supported for QoS Policy. Traffic will be matched with alternative clas-maps/class-default

firmware

" Unconfigure the ACE with unsupported protocol" " detach and re-attach the policy"

QOSMGR-3-L4OP_ACL_NEQ_CONFLICT

3-Error

NEQ L4 operation not supported

Trying to configure NEQ operation.

firmware

"Remove QOS ACL configured on interface."

RMGR-3-OUT_OF_TCAM_IPV4_ROUTE

3-Error

Out of tcam resources to execute command

Number of IPv4 routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 routes configured " "to supported scale"

MCASTV4-3-OUT_OF_TCAM_IPV4_MCAST

3-Error

[chars] : Out of tcam space. Current Tcam Count is [dec]

Number of IPv4 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 mcast routes " "configured to supported scale"

MCASTV6-3-OUT_OF_TCAM_IPV6_MCAST

3-Error

[chars]: Out of tcam space. Current v6MC Count: [dec]

Number of IPv6 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv6 mcast routes " "configured to supported scale"

MPLS-3-OUT_OF_LABEL3_SPACE

3-Error

Out of resource to create labels

Number of empls 3d labels exceeded supported scale

firmware

"Please reduce the number of empls 3d labels to " "supported scale"

MPLS-3-OUT_OF_LABEL_SPACE

3-Error

Out of resource to create labels

Number of empls intd labels exceeded supported scale

firmware

"Please reduce the number of empls intd labels to " "supported scale"

MPLS-3-MAX_PW_EXCEEDED

3-Error

Number of PW's exceeded supported limit [dec]

Number of empls intd labels exceeded supported scale

firmware

"Please reduce the number of PW's to supported scale"

MPLS-3-MPLS_MTU_ALLOC_FAIL

3-Error

Out of resource to allocate mpls mtu

mpls mtu exceeded supported scale

asr903-mpls

"Please reduce the number of mpls mtu configured values" "to supported scale"

MPLS-3-FRR_BDI_UNSUPPORTED

3-Error

FRR not enabled on [chars]. Unsupported EFP and trunk EFP count [dec]. Supported 1

LFA FRR support on ASR903 for BDI interface is available with just one EFP or trunk EFP

asr903-mpls

"shutdown the BDI interface. Remove all the " " EFPs/TEFPs under the BDI. Create just one EFP or TEFP." " no shutdown the BDI interface"

MPLS-4-PIC_BDI_UNSUPPORTED

4-Warning

BGP PIC not enabled on [chars]: [chars]

Hardware could not be programmed for BGP PIC support on BDI interface

asr903-mpls

"Collect the logs and contect Cisco TAC"

CEF-3-NILE_CEF_MAX_VRF_EXCEEDED

3-Error

Number of VRF instances exceeded allowed limit [dec]

Number of vrf instances exceeded supported platform scale

firmware

"Please reduce the number of vrf instances" "to scale to platform supported scale"

BACKWALK-2-TOO_MANY_DEPENDENTS

2-Critical

UEA OCE backwalk aborted - too many dependents

Too many dependent objects > 200k were encountered during backwalk from an OCE chain object

rsp3-layer3

"Please reduce the number of IGP routes below " "200k."

QOSMGR-3-ASIC_PROGRAMMING_FAIL

3-Error

Fails to program the ASIC for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_PROGRAMMING_FAIL

3-Error

Fails to program TCAM for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_EXHAUSTION

3-Error

Internal Error in resource allocation

The system is running out of TCAM entries to support the number of traffic classes in the policy-map. The maximum number of TCAM entries is platform dependent.

firmware

"Reduce the number of classes in attached policy-maps"

QOSMGR-3-LABEL_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of QoS label to support the number of traffic classes in all attached policy-maps.

firmware

"Reduce the number of distinctive class-maps matches " "or 'set' actions in attached policy-maps"

QOSMGR-4-STATISTICS_FAIL

4-Warning

Internal Error in reading statistics

Can not access to HW to read statistics successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TDM_OC_HIERARCHY_UNSUPPORTED

3-Error

Only two-level hierarchy is supported on TDM/OC3/OC12 interfaces

Unsupported QoS hierarchy on TDM/OC3/OC12 interfaces

firmware

"Change config to reduce to two-level policy"

QOSMGR-3-POLICER_PROGRAMMING_FAIL

3-Error

Fails to program HW policer

Can not access to HW successfully.

firmware

""

QOSMGR-4-POLICER_EXCEEDING_HW

4-Warning

Policer configuration has exceeded hardware limitation for policymap [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-4-POLICER_PROFILE_EXCEEDED

4-Warning

Policer profiles have exceeded the maximum number [dec]

Max number for Qos policer profiles has reached

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-4-IDMGR_RESOURCE_EXCEEDED

4-Warning

[chars] has exceeded its maximum number : [dec]

Max number of FLOW ID allocation has reached

firmware

"reduce the number of flow id allocation for the interface"

QOSMGR-3-INGRESS_QOS_HANDLE_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-handle to support specified policy-map.

firmware

""

QOSMGR-3-INGRESS_QOS_PROFILED_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-profiled to support the specified policy-map.

firmware

""

QOSMGR-3-SCHEDULER_PROGRAMMING_FAIL

3-Error

Fails to program HW scheduler

Can not access to HW successfully.

firmware

""

QOSMGR-4-QUEUE_EXCEEDING_HW

4-Warning

Number of queues has exceeded the hardware limitation for VOQs

The system is running out of output queues to support the specified policy-map.

firmware

"Remove the EFPs from the interfaces"

QOSMGR-4-VOQ_CONNECTOR_EXCEEDING_HW

4-Warning

Number of VOQ connectors has exceeded the hardware limitation for [chars] in asic id : [dec]

The system is running out of output queues to support the specified policy-map.

firmware

"Remove the EFPs from the interfaces"

QOSMGR-4-GPORT_SCHEDULER_EXCEEDING_HW

4-Warning

[chars] has exceeded the hardware limitation

The system is running out of output queues to support the specified policy-map.

firmware

"Remove the EFPs from the interfaces"

QOSMGR-4-INVALID_POLICYMAP_DUE_NON_QOS_EVENT

4-Warning

The policy-map [chars] is detached due to the event [chars].

The attached policy-map becomes invalid due to the change of the port speed.

firmware

"Change the shaping/bandwidth of the output policy-map and re-attach to the interface ."

QOSMGR-3-OUT_OF_TCAM_RESOURCES

3-Error

Out of tcam resources to execute command

Lack of tcam resources due to higher tcam resource requirements

firmware

"Change config to reduce tcam entry usage"

QOSMGR-3-PROFILES_EXHAUSTED

3-Error

Out of rm profiles to execute command

No free RM profile to accommodate the request

firmware

"Change config to reduce or reuse RM profiles"

QOSMGR-3-QUEUE_FLUSH_FAILED

3-Error

Queue-Flush not successful

Scheduler unable to flush the queue

firmware

"Remove any shape configuration for the queue"

QOSMGR-3-MAX_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum queue-limit commands per class

Trying to exceed the maximum queue-limit commands allowed per class

firmware

"Try reducing queue-limit commands under the class"

QOSMGR-3-MAX_QUALIFIED_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum qualified queue-limit commands per class

Trying to exceed the maximum qualified queue-limit commands allowed per class

firmware

"Try reducing qualified queue-limit commands " "under the class"

QOSMGR-3-UNSUPPORTED_QLIMIT_UNITS

3-Error

Qlimit unit other than usec & byte is not supported

Trying to configure a qlimit unit other than bytes or usec

firmware

"Configure qlimit in terms of bytes or usec"

QOSMGR-3-QLIMIT_VALUE_OUT_OF_RANGE

3-Error

Qlimit value is out of range

Trying to configure a qlimit value outside the supported range

firmware

"Configure qlimit value within supported range"

QOSMGR-3-QLIMIT_LEVEL_ERROR

3-Error

Qlimit command not supported in non-leaf classes

Trying to configure qlimit in a non leaf class

firmware

"Configure qlimit only in leaf classes"

QOSMGR-3-MANUAL_SHAPE_EXCEEDS_SPEED

3-Error

Invalid policy-map detected during interface speed change

Shape value in policy exceeds port speed

firmware

"Configure lesser shape value which will not " "exceed interface speed"

QOSMGR-3-BANDWIDTH_OVERSUBSCRIBED

3-Error

Bandwidth oversubscribed in the interface

Sum of committed bandwidth at a particular level exceeds the sum total of interface's max bandwidth

firmware

"Reduce the committed bandwidth to be less that " "interface's max bandwidth"

QOSMGR-3-SHAPE_UNDERFLOW

3-Error

New shape/speed value is less than the total bandwidth configured in the interface

Shape/speed configured is less than the total bandwidth configured in the interface

firmware

"Increase the shape/speed value or reduce " "the bandwidth configured in the child classes"

QOSMGR-3-BANDWIDTH_LEVEL_ERROR

3-Error

Bandwidth command not acceptable at interface level

Hardware does not support bandwidth at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-PRIORITY_LEVEL_ERROR

3-Error

Priority command not acceptable at interface level

Hardware does not support priority at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-BANDWIDTH_SHAPE_ERROR

3-Error

Bandwidth configured is greater than shapePIR of the class

Bandwidth should not be greater than shape value

firmware

"Reduce the bandwidth value to less than" " class's shapePIR value"

QOSMGR-3-BANDWIDTH_PARENT_SHAPE_ERROR

3-Error

Sum of bandwidths is greater than parent class's shapePIR

Total bandwidth of the classes at the same level exceeds the parent class's shapePIR value

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_PARENT_ERROR

3-Error

Sum of bandwidths is greater than parent class's bandwidth

Total bandwidth of the classes at the same level exceeds the parent class's bandwidth

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_CHILD_ERROR

3-Error

Bandwidth in one of the children class is greater than input bandwidth

Children class's bandwidth should not be greater

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-PROFILE_EXHAUST

3-Error

No free scheduler profiles available in hardware

With the new configuration there is no free profile available in the HW this could be because of dissimilar profiles configured at the same hierarchy level

firmware

"Change the config value to closest existing config"

QOSMGR-3-EFP_SHAPE_RESTRICTION

3-Error

EFP policies cannot have shape command at physical level and more than one logical level classes

Since the HW does not support four level hierarchy EFP policies sit in pseudo level between Physical and Logical level

firmware

"Either remove vlan hierarchy in the EFP policy or" " do not configure shape command at physical level"

QOSMGR-3-SHAPE_PARENT_ERROR

3-Error

Shape value is greater than parent class's shape or interface's speed

Parent class's shape value cannot be smaller than current

firmware

"Configure shape value lesser than parent class's" " shape or interface's speed"

QOSMGR-3-SHAPE_CHILD_ERROR

3-Error

One of children class's shape config is higher

Children class's shape should not be higher than current

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_CHILD_BANDWIDTH_ERROR

3-Error

Bandwidth in one of the children class is greater than input shape value

Children class's bandwidth should not be higher than input

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_BANDWIDTH_PERCENT_ERROR

3-Error

Shape - Bandwidth-percent values inconsistent in the hierarchy calculated bandwidth will exceed shape

Because of this new shape command Bandwidth percent configured in one of children class will get more value than its manually configured shape. Please note that bandwidth percent is calculated from parent's shapePIR

firmware

"Either configure higher shape value or " " reduce violating bandwidth-percent value"

QOSMGR-3-LOGICAL_RESOURCE_EXHAUSTED

3-Error

Logical level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused logical level classes"

QOSMGR-3-QUEUE_EXHAUSTED

3-Error

Class level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused class level classes"

QOSMGR-3-EQOS_CXT_EXCEEDED

3-Error

Maximum Egress QosContexts consumed in the Bridge-Domain

Number of Egress QoS vlan matches exceeds the maximum allowed in the Bridge-Domain

firmware

"Reduce the number of Egress QoS vlan" " matches in the Bridge-Domain and try again"

QOSMGR-3-PROTOCOL_NOT_SUPPORTED_FOR_POLICY

3-Error

The configured protocol is not supported in QoS policy

Configured protocol is not supported for QoS Policy. Traffic will be matched with alternative clas-maps/class-default

firmware

" Unconfigure the ACE with unsupported protocol" " detach and re-attach the policy"

QOSMGR-3-MARKING_PROFILES_EXHAUSTED

3-Error

Out of marking profiles to execute command

No free marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-INGRESS_MARKING_PROFILES_EXHAUSTED

3-Error

Ingress marking profiles have exceeded the maxinum number [dec]

No free ingress cos marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-EGRESS_MARKING_PROFILES_EXHAUSTED

3-Error

Egress marking profiles have exceeded the maxinum number [dec]

No free egress cos marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-INGRESS_QOSGROUP_MARKING_PROFILES_EXHAUSTED

3-Error

Ingress Exp and qos-group marking profiles have exceeded the maxinum number [dec]

No free ingress qos-group marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-QOSMGR_POLICYMAP_ERROR

3-Error

policy-map applied on [chars] is in error condition

The policy-map applied on the printed target may not work or the stats for that target will not work.

rsp3-qos

"Collect the uea_mgr logs"

RMGR-3-OUT_OF_TCAM_IPV4_ROUTE

3-Error

Out of tcam resources to execute command

Number of IPv4 routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 routes configured " "to supported scale"

MCASTV4-3-OUT_OF_TCAM_IPV4_MCAST

3-Error

[chars] : Out of tcam space. Current Tcam Count is [dec]

Number of IPv4 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv4 mcast routes " "configured to supported scale"

MCASTV6-3-OUT_OF_TCAM_IPV6_MCAST

3-Error

[chars]: Out of tcam space. Current v6MC Count: [dec]

Number of IPv6 mcast routes installed exceeded supported scale

firmware

"Please reduce the number of IPv6 mcast routes " "configured to supported scale"

MPLS-3-OUT_OF_LABEL3_SPACE

3-Error

Out of resource to create labels

Number of empls 3d labels exceeded supported scale

firmware

"Please reduce the number of empls 3d labels to " "supported scale"

MPLS-3-OUT_OF_LABEL_SPACE

3-Error

Out of resource to create labels

Number of empls intd labels exceeded supported scale

firmware

"Please reduce the number of empls intd labels to " "supported scale"

MPLS-3-MAX_PW_EXCEEDED

3-Error

Number of PW's exceeded supported limit [dec]

Number of empls intd labels exceeded supported scale

firmware

"Please reduce the number of PW's to supported scale"

MPLS-3-MAX_RPW_EXCEEDED

3-Error

Number of Routed PW's exceeded supported limit [dec]

Number of Routed PW exceeded supported scale

firmware

"Please reduce the number of Routed PW's to " "supported scale"

MPLS-3-MPLS_MTU_ALLOC_FAIL

3-Error

Out of resource to allocate mpls mtu

mpls mtu exceeded supported scale

asr903-mpls

"Please reduce the number of mpls mtu configured values" "to supported scale"

MPLS-3-FRR_BDI_UNSUPPORTED

3-Error

FRR not enabled on [chars]. Unsupported EFP and trunk EFP count [dec]. Supported 1

LFA FRR support on ASR903 for BDI interface is available with just one EFP or trunk EFP

asr903-mpls

"shutdown the BDI interface. Remove all the " " EFPs/TEFPs under the BDI. Create just one EFP or TEFP." " no shutdown the BDI interface"

MPLS-4-PIC_BDI_UNSUPPORTED

4-Warning

BGP PIC not enabled on [chars]: [chars]

Hardware could not be programmed for BGP PIC support on BDI interface

asr903-mpls

"Collect the logs and contect Cisco TAC"

CEF-3-NILE_CEF_MAX_VRF_EXCEEDED

3-Error

Number of VRF instances exceeded allowed limit [dec]

Number of vrf instances exceeded supported platform scale

firmware

"Please reduce the number of vrf instances" "to scale to platform supported scale"

BACKWALK-2-TOO_MANY_DEPENDENTS

2-Critical

UEA OCE backwalk aborted - too many dependents

Too many dependent objects > 200k were encountered during backwalk from an OCE chain object

rsp3-layer3

"Please reduce the number of IGP routes below " "200k."

QOSMGR-3-ASIC_PROGRAMMING_FAIL

3-Error

Fails to program the ASIC for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_PROGRAMMING_FAIL

3-Error

Fails to program TCAM for policymap [chars]

Can not access to HW successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TCAM_EXHAUSTION

3-Error

Internal Error in resource allocation

The system is running out of TCAM entries to support the number of traffic classes in the policy-map. The maximum number of TCAM entries is platform dependent.

firmware

"Reduce the number of classes in attached policy-maps"

QOSMGR-3-LABEL_EXHAUST

3-Error

Internal Error in resource allocation

The system is running out of QoS label to support the number of traffic classes in all attached policy-maps.

firmware

"Reduce the number of distinctive class-maps matches " "or 'set' actions in attached policy-maps"

QOSMGR-4-STATISTICS_FAIL

4-Warning

Internal Error in reading statistics

Can not access to HW to read statistics successfully.

firmware

LOG_STD_ACTION

QOSMGR-3-TDM_OC_HIERARCHY_UNSUPPORTED

3-Error

Only two-level hierarchy is supported on TDM/OC3/OC12 interfaces

Unsupported QoS hierarchy on TDM/OC3/OC12 interfaces

firmware

"Change config to reduce to two-level policy"

QOSMGR-3-POLICER_PROGRAMMING_FAIL

3-Error

Fails to program HW policer

Can not access to HW successfully.

firmware

""

QOSMGR-4-POLICER_EXCEEDING_HW

4-Warning

Policer configuration has exceeded hardware limitation for policymap [chars]

The system is running out of policers to support the specified policy-maps.

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-4-POLICER_PROFILE_EXCEEDED

4-Warning

Policer profiles have exceeded the maximum number [dec]

Max number for Qos policer profiles has reached

firmware

"Reduce the number of policer usage in attached input policy-maps. "

QOSMGR-4-IDMGR_RESOURCE_EXCEEDED

4-Warning

[chars] has exceeded its maximum number : [dec]

Max number of FLOW ID allocation has reached

firmware

"reduce the number of flow id allocation for the interface"

QOSMGR-3-INGRESS_QOS_HANDLE_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-handle to support specified policy-map.

firmware

""

QOSMGR-3-INGRESS_QOS_PROFILED_EXCEEDED

3-Error

Internal Error in resource allocation

The system is running out of qos-profiled to support the specified policy-map.

firmware

""

QOSMGR-3-SCHEDULER_PROGRAMMING_FAIL

3-Error

Fails to program HW scheduler

Can not access to HW successfully.

firmware

""

QOSMGR-4-QUEUE_EXCEEDING_HW

4-Warning

Number of queues has exceeded the hardware limitation for VOQs

The system is running out of output queues to support the specified policy-map.

firmware

"Remove the EFPs from the interfaces"

QOSMGR-4-VOQ_CONNECTOR_EXCEEDING_HW

4-Warning

Number of VOQ connectors has exceeded the hardware limitation for [chars] in asic id : [dec]

The system is running out of output queues to support the specified policy-map.

firmware

"Remove the EFPs from the interfaces"

QOSMGR-4-GPORT_SCHEDULER_EXCEEDING_HW

4-Warning

[chars] has exceeded the hardware limitation

The system is running out of output queues to support the specified policy-map.

firmware

"Remove the EFPs from the interfaces"

QOSMGR-4-INVALID_POLICYMAP_DUE_NON_QOS_EVENT

4-Warning

The policy-map [chars] is detached due to the event [chars].

The attached policy-map becomes invalid due to the change of the port speed.

firmware

"Change the shaping/bandwidth of the output policy-map and re-attach to the interface ."

QOSMGR-3-OUT_OF_RESOURCES

3-Error

Out of TCAM/LPM resources to execute command

Lack of TCAM/LPM resources due to higher resource requirements

firmware

"Change config to reduce tcam entry usage"

QOSMGR-3-UNSUPPORTED_FILTERS

3-Error

Installed Policy-map has filters which are not supported.Detach re-configure and attach the policy

Policy-map has filters which are not supported

firmware

"Change config to use only supported filters" " detach and re-attach the policy"

QOSMGR-3-PROFILES_EXHAUSTED

3-Error

Out of rm profiles to execute command

No free RM profile to accommodate the request

firmware

"Change config to reduce or reuse RM profiles"

QOSMGR-3-QUEUE_FLUSH_FAILED

3-Error

Queue-Flush not successful

Scheduler unable to flush the queue

firmware

"Remove any shape configuration for the queue"

QOSMGR-3-MAX_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum queue-limit commands per class

Trying to exceed the maximum queue-limit commands allowed per class

firmware

"Try reducing queue-limit commands under the class"

QOSMGR-3-MAX_QUALIFIED_QLIMIT_COMMANDS_EXCEEDED

3-Error

Exceeding the maximum qualified queue-limit commands per class

Trying to exceed the maximum qualified queue-limit commands allowed per class

firmware

"Try reducing qualified queue-limit commands " "under the class"

QOSMGR-3-UNSUPPORTED_QLIMIT_UNITS

3-Error

Qlimit unit other than usec & byte is not supported

Trying to configure a qlimit unit other than bytes or usec

firmware

"Configure qlimit in terms of bytes or usec"

QOSMGR-3-QLIMIT_VALUE_OUT_OF_RANGE

3-Error

Qlimit value is out of range

Trying to configure a qlimit value outside the supported range

firmware

"Configure qlimit value within supported range"

QOSMGR-3-QLIMIT_LEVEL_ERROR

3-Error

Qlimit command not supported in non-leaf classes

Trying to configure qlimit in a non leaf class

firmware

"Configure qlimit only in leaf classes"

QOSMGR-3-MANUAL_SHAPE_EXCEEDS_SPEED

3-Error

Invalid policy-map detected during interface speed change

Shape value in policy exceeds port speed

firmware

"Configure lesser shape value which will not " "exceed interface speed"

QOSMGR-3-BANDWIDTH_OVERSUBSCRIBED

3-Error

Bandwidth oversubscribed in the interface

Sum of committed bandwidth at a particular level exceeds the sum total of interface's max bandwidth

firmware

"Reduce the committed bandwidth to be less that " "interface's max bandwidth"

QOSMGR-3-SHAPE_UNDERFLOW

3-Error

New shape/speed value is less than the total bandwidth configured in the interface

Shape/speed configured is less than the total bandwidth configured in the interface

firmware

"Increase the shape/speed value or reduce " "the bandwidth configured in the child classes"

QOSMGR-3-BANDWIDTH_LEVEL_ERROR

3-Error

Bandwidth command not acceptable at interface level

Hardware does not support bandwidth at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-PRIORITY_LEVEL_ERROR

3-Error

Priority command not acceptable at interface level

Hardware does not support priority at physical level

firmware

"Do not apply bandwidth command at interface " "level policy"

QOSMGR-3-BANDWIDTH_SHAPE_ERROR

3-Error

Bandwidth configured is greater than shapePIR of the class

Bandwidth should not be greater than shape value

firmware

"Reduce the bandwidth value to less than" " class's shapePIR value"

QOSMGR-3-BANDWIDTH_PARENT_SHAPE_ERROR

3-Error

Sum of bandwidths is greater than parent class's shapePIR

Total bandwidth of the classes at the same level exceeds the parent class's shapePIR value

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_PARENT_ERROR

3-Error

Sum of bandwidths is greater than parent class's bandwidth

Total bandwidth of the classes at the same level exceeds the parent class's bandwidth

firmware

"Reduce the bandwidth value"

QOSMGR-3-BANDWIDTH_CHILD_ERROR

3-Error

Bandwidth in one of the children class is greater than input bandwidth

Children class's bandwidth should not be greater

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-PROFILE_EXHAUST

3-Error

No free scheduler profiles available in hardware

With the new configuration there is no free profile available in the HW this could be because of dissimilar profiles configured at the same hierarchy level

firmware

"Change the config value to closest existing config"

QOSMGR-3-EFP_SHAPE_RESTRICTION

3-Error

EFP policies cannot have shape command at physical level and more than one logical level classes

Since the HW does not support four level hierarchy EFP policies sit in pseudo level between Physical and Logical level

firmware

"Either remove vlan hierarchy in the EFP policy or" " do not configure shape command at physical level"

QOSMGR-3-SHAPE_PARENT_ERROR

3-Error

Shape value is greater than parent class's shape or interface's speed

Parent class's shape value cannot be smaller than current

firmware

"Configure shape value lesser than parent class's" " shape or interface's speed"

QOSMGR-3-SHAPE_CHILD_ERROR

3-Error

One of children class's shape config is higher

Children class's shape should not be higher than current

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_CHILD_BANDWIDTH_ERROR

3-Error

Bandwidth in one of the children class is greater than input shape value

Children class's bandwidth should not be higher than input

firmware

"Either increase input value or decrese erring one"

QOSMGR-3-SHAPE_BANDWIDTH_PERCENT_ERROR

3-Error

Shape - Bandwidth-percent values inconsistent in the hierarchy calculated bandwidth will exceed shape

Because of this new shape command Bandwidth percent configured in one of children class will get more value than its manually configured shape. Please note that bandwidth percent is calculated from parent's shapePIR

firmware

"Either configure higher shape value or " " reduce violating bandwidth-percent value"

QOSMGR-3-LOGICAL_RESOURCE_EXHAUSTED

3-Error

Logical level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused logical level classes"

QOSMGR-3-QUEUE_EXHAUSTED

3-Error

Class level queuing resource exhausted [chars]

Maximum resources used

firmware

"Free up unused class level classes"

QOSMGR-3-EQOS_CXT_EXCEEDED

3-Error

Maximum Egress QosContexts consumed in the Bridge-Domain

Number of Egress QoS vlan matches exceeds the maximum allowed in the Bridge-Domain

firmware

"Reduce the number of Egress QoS vlan" " matches in the Bridge-Domain and try again"

QOSMGR-3-PROTOCOL_NOT_SUPPORTED_FOR_POLICY

3-Error

The configured protocol is not supported in QoS policy

Configured protocol is not supported for QoS Policy. Traffic will be matched with alternative clas-maps/class-default

firmware

" Unconfigure the ACE with unsupported protocol" " detach and re-attach the policy"

QOSMGR-3-MARKING_PROFILES_EXHAUSTED

3-Error

Out of marking profiles to execute command

No free marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-INGRESS_MARKING_PROFILES_EXHAUSTED

3-Error

Ingress marking profiles have exceeded the maxinum number [dec]

No free ingress cos marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-EGRESS_MARKING_PROFILES_EXHAUSTED

3-Error

Egress marking profiles have exceeded the maxinum number [dec]

No free egress cos marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-INGRESS_QOSGROUP_MARKING_PROFILES_EXHAUSTED

3-Error

Ingress Exp and qos-group marking profiles have exceeded the maxinum number [dec]

No free ingress qos-group marking profile to accommodate the request

firmware

"Change config to reuse the existing profiles"

QOSMGR-3-QOSMGR_POLICYMAP_ERROR

3-Error

policy-map applied on [chars] is in error condition

The policy-map applied on the printed target may not work or the stats for that target will not work.

rsp3-qos

"Collect the uea_mgr logs"

Additional References

Technical Assistance

When the recommended action of an error message advises that you contact Cisco technical support, open a case with the Cisco Technical Assistance Center (TAC).

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

https://www.cisco.com/c/en/us/support/index.html