Table Of Contents
Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card with Universal Cable Holder—UCH1
Obtaining Documentation and Submitting a Service Request
Quick Start Guide
Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card with Universal Cable Holder—UCH1
First Published: November 22, 2002Last Updated: April 08, 2011OL-24891-01Contents
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Caution Use an ESD-preventive wrist or ankle strap during the line card installation.
Feature Description
The Cisco uBR10-MC5X20S, U, and H cable interface line cards use 75-ohm precision video coax cables and 75-ohm MCX connectors to connect to the CMTS.
This document describes how to install and remove cables and the first generation universal cable holder (UCH1).
Figure 1 shows the cards in a Cisco uBR10012 router.
Figure 1 Cisco uBR10-MC5X20S/U/H Cards
The cables come in kits that consist of cable sets and spare F connectors.
The MC5X20 dual-shielded cable kit includes:
•Two 10-bundle MCX to "F" conn., 3-m cables
•One 5-bundle MCX to "F" conn., 3-m cables
•5 spare F connectors
The MC5X20 quad-shielded cable kit includes:
•Five 5-bundle MCX to "F" conn., 3-m cables
•Five spare F connectors
The cable kits do not contain the universal cable holders; however, the UCH is available with line card accessory kits and spare cards. Or, the UCH2 is available as a spare.
Note In European markets only, you must use the quad-shielded cable kit with the Cisco uBR10-MC5X20H.
Tools required for cable installation include:
•1/4-in. slotted screwdriver and T-10 TORX driver
•Cable extractor tool
Also see "Tool Manufacturers and Part Numbers."
Installing the Cables
The UCH must be used for all Cisco uBR10-
MC5X20S/U/H line card cable connections. Failure to use the UCH may cause permanent damage to the line card connectors and result in low or no RF output.
Caution Do not attempt to remove or install cables in the UCH1 if the UCH1 is attached to the faceplate.
Step 1 Remove the cable clamp bar from the UCH1. See Figure 2.
Figure 2 Removing the Cable Clamp Bar
Step 2 Remove the ESD cap from a cable, and insert it into the UCH. See Figure 3. We recommend that the cables be installed in the UCH as shown in Table 1.
Caution If using quad-shielded cables, make sure there is no heat-shrink wrap on the ends by the MCX connectors.
Table 1 Port—Dual/Quad-Shielded Cable Colors
Table 2 Port—Legacy 5-Color Quad-Shielded Cable Colors
Step 3 Wiggle the cable until you feel the connector click into place in the UCH.
Caution Be sure to not kink the cables.
Figure 3 Inserting a Cable in the UCH1
Step 4 Repeat this procedure for all of the cables.
Step 5 Align the cables with the slots in the UCH1 and clamp bar, and then replace the clamp bar.
Step 6 Using the T-10 TORX driver tool, tighten the screws on the clamp bar (maximum torque—10 in-lbs). See Figure 2.
Installing the UCH
After the cables are installed in the UCH, follow these steps to prevent ESD damage to the line card.
Note Before proceeding, remove the protective sticker covering the line card DS ports.
Step 1 Make sure that you are grounded using an ESD-preventive wrist or ankle strap.
Step 2 Attach a jumper cable to the ground point on the chassis.
Step 3 Briefly touch each cable's center connector with the jumper cable to remove any built-up ESD potential.
Step 4 Align the red line on the UCH with the red triangle on the faceplate.
Figure 4 Installing the UCH
Step 5 Align the end pins with the pin holes in the faceplate, and guide the UCH onto the faceplate.
Step 6 Hold the cables and UCH in place while finger tightening the leadscrew. Do not bend the cables at right angles.
Step 7 Use the flathead screwdriver to tighten the leadscrew 10 in-lbs, (maximum torque 15 in-lbs).
Caution Torquing the leadscrew to more than 20 in.-lbs can cause the leadscrew to fail.
The UCH1 is fully engaged when the retractable shroud is aligned with the black lines. See Figure 5.
Removing the UCH
Step 1 Make sure that you are grounded using an ESD-preventive wrist or ankle strap.
Step 2 Loosen the lead screw (counterclockwise) until it disengages from the faceplate.
Step 3 Gently pull the UCH straight away from the faceplate.
Note If the UCH does not easily pull away from the card, loosen the lead screw until it completely disengages from the faceplate.
Figure 5 Removing the UCH
Removing the Cables
Step 1 Use the T-10 TORX driver tool to remove the cable clamp bar.
Caution Be careful not to bend the cables.
Step 2 Hold the UCH1 in your hand and place the extraction tool over the connector that you are removing. See Figure 6.
Step 3 Carefully push down on the extraction tool, turning slightly to disengage the spring.
Step 4 Push the cable out of the hole. There is a click when it disengages from the UCH1.
Figure 6 Using the Cable Extraction Tool
Troubleshooting
Check the following:
1. Verify that the lead screw is tight.
2. Verify that the shroud fits snugly against the faceplate (the cutouts are closed).
3. Verify that the cables are properly seated and secure in the UCH.
If downstream RF power measurements are made, use these ESD precautions to prevent damage to the product:
1. Check for a proper ground on the equipment and chassis before connecting any cables.
2. Ensure that there is a common ground between all the test equipment that you are using and the unit under test.
3. Keep test cables as short as possible to limit static buildup.
4. Before attaching any test cables to the unit under test, momentarily ground the center pin of the test cable to remove any ESD potential that may be present.
Contact Cisco TAC for further information:
Tool Manufacturers and Part Numbers
Related Documentation
•Installing Cisco uBR10-MC5X20S/U/H Cable Interface Line Cards - Quick Start Guide
•Cisco uBR10012 Universal Broadband Router Hardware Installation Guide
http://www.cisco.com/en/US/docs/cable/cmts/ubr10012/installation/guide/hig.html
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Copyright © 2002-2011 Cisco Systems, Inc. All rights reserved.