Table Of Contents
SIP—INFO Method for DTMF Tone Generation
Prerequisites for SIP—INFO Method for DTMF Tone Generation
Information About SIP—INFO Method for DTMF Tone Generation
How to Review SIP INFO Messages
Configuring for SIP—INFO Method for DTMF Tone Generation
SIP—INFO Method for DTMF Tone Generation
The SIP—INFO Method for DTMF Tone Generation feature uses the Session Initiation Protocol (SIP) INFO method to generate dual tone multifrequency (DTMF) tones on the telephony call leg. SIP info methods, or request message types, request a specific action be taken by another user agent (UA) or proxy server. The SIP INFO message is sent along the signaling path of the call. Upon receipt of a SIP INFO message with DTMF relay content, the gateway generates the specified DTMF tone on the telephony end of the call.
Prerequisites for SIP—INFO Method for DTMF Tone Generation
Cisco Unified Border Element
•
Cisco IOS Release 12.2(11)T or a later release must be installed and running on your Cisco Unified Border Element.
Cisco Unified Border Element (Enterprise)
•
Cisco IOS XE Release 2.5 or a later release must be installed and running on your Cisco ASR 1000 Series Router.
Information About SIP—INFO Method for DTMF Tone Generation
The SIP—INFO Method for DTMF Tone Generation feature is always enabled, and is invoked when a SIP INFO message is received with DTMF relay content. This feature is related to the DTMF Events Through SIP Signaling feature, which allows an application to be notified about DTMF events using SIP NOTIFY messages. Together, the two features provide a mechanism to both send and receive DTMF digits along the signaling path. For more information on sending DTMF event notification using SIP NOTIFY messages, refer to the DTMF Events Through SIP Signaling feature.
How to Review SIP INFO Messages
The SIP INFO method is used by a UA to send call signaling information to another UA with which it has an established media session. The following example shows a SIP INFO message with DTMF content:
INFO sip:2143302100@172.17.2.33 SIP/2.0Via: SIP/2.0/UDP 172.80.2.100:5060From: <sip:9724401003@172.80.2.100>;tag=43To: <sip:2143302100@172.17.2.33>;tag=9753.0207Call-ID: 984072_15401962@172.80.2.100CSeq: 25634 INFOSupported: 100relSupported: timerContent-Length: 26Content-Type: application/dtmf-relaySignal= 1Duration= 160This sample message shows a SIP INFO message received by the gateway with specifics about the DTMF tone to be generated. The combination of the "From", "To", and "Call-ID" headers identifies the call leg. The signal and duration headers specify the digit, in this case 1, and duration, 160 milliseconds in the example, for DTMF tone play.
Prerequisites
The following are general prerequisites for SIP functionality:
•
Ensure that the gateway has voice functionality that is configured for SIP.
•
Establish a working IP network.
•
Configure VoIP.
Restrictions
The SIP—INFO Method for DTMF Tone Generation feature includes the following signal duration parameters:
•
Minimum signal duration is 100 milliseconds (ms). If a request is received with a duration less than 100 ms, the minimum duration of 100 ms is used by default.
•
Maximum signal duration is 5000 ms. If a request is received with a duration longer than 5000 ms, the maximum duration of 5000 ms is used by default.
•
If no duration parameter is included in a request, the gateway defaults to a signal duration of 250 ms.
Configuring for SIP—INFO Method for DTMF Tone Generation
You cannot configure, enable, or disable this feature. No configuration tasks are required to configure the SIP - INFO Method for DTMF Tone Generation feature. The feature is enabled by default.
Troubleshooting Tips
You can display SIP statistics, including SIP INFO method statistics, by using the show sip-ua statistics and show sip-ua status commands in privileged EXEC mode. See the following fields for SIP INFO method statistics:
•
OkInfo 0/0, under SIP Response Statistics, Success, displays the number of successful responses to an INFO request.
•
Info 0/0, under SIP Total Traffic Statistics, displays the number of INFO messages received and sent by the gateway.
The following is sample output from the show sip-ua statistics command:
Router# show sip-ua statistics
SIP Response Statistics (Inbound/Outbound)Informational:Trying 1/1, Ringing 0/0,Forwarded 0/0, Queued 0/0,SessionProgress 0/1Success:OkInvite 0/1, OkBye 1/0,OkCancel 0/0, OkOptions 0/0,OkPrack 0/0, OkPreconditionMet 0/0OkSubscibe 0/0, OkNotify 0/0,
OkInfo 0/0, 202Accepted 0/0Redirection (Inbound only):MultipleChoice 0, MovedPermanently 0,MovedTemporarily 0, SeeOther 0,UseProxy 0, AlternateService 0Client Error:BadRequest 0/0, Unauthorized 0/0,PaymentRequired 0/0, Forbidden 0/0,NotFound 0/0, MethodNotAllowed 0/0,NotAcceptable 0/0, ProxyAuthReqd 0/0,ReqTimeout 0/0, Conflict 0/0, Gone 0/0,LengthRequired 0/0, ReqEntityTooLarge 0/0,ReqURITooLarge 0/0, UnsupportedMediaType 0/0,BadExtension 0/0, TempNotAvailable 0/0,CallLegNonExistent 0/0, LoopDetected 0/0,TooManyHops 0/0, AddrIncomplete 0/0,Ambiguous 0/0, BusyHere 0/0,BadEvent 0/0Server Error:InternalError 0/0, NotImplemented 0/0,BadGateway 0/0, ServiceUnavail 0/0,GatewayTimeout 0/0, BadSipVer 0/0Global Failure:BusyEverywhere 0/0, Decline 0/0,NotExistAnywhere 0/0, NotAcceptable 0/0SIP Total Traffic Statistics (Inbound/Outbound)Invite 0/0, Ack 0/0, Bye 0/0,Cancel 0/0, Options 0/0,Prack 0/0, Comet 0/0,Subscribe 0/0, Notify 0/0,Refer 0/0, Info 0/0Retry StatisticsInvite 0, Bye 0, Cancel 0, Response 0, Notify 0The following is sample output from the show sip-ua status command:
Router# show sip-ua status
SIP User Agent StatusSIP User Agent for UDP : ENABLEDSIP User Agent for TCP : ENABLEDSIP User Agent bind status(signaling): DISABLEDSIP User Agent bind status(media): DISABLEDSIP max-forwards : 6SIP DNS SRV version: 2 (rfc 2782)SDP application configuration:Version line (v=) requiredOwner line (o=) requiredSession name line (s=) requiredTimespec line (t=) requiredMedia supported: audio imageNetwork types supported: INAddress types supported: IP4Transport types supported: RTP/AVP udptl