Table Of Contents

Two-Rate Policer

Contents

Feature Overview

Benefits

Restrictions

Prerequisites

Configuration Tasks

Configuring the Two-Rate Policer

Verifying the Two-Rate Policer Configuration

Troubleshooting Tips

Monitoring and Maintaining the Two-Rate Policer

Configuration Examples

Limiting the Traffic Using a Policer Class: Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Command Reference

Two-Rate Policer

---

First Published: October 15, 2001

Last Updated: May 5, 2008

This document describes the Two-Rate Policer feature and explains how to configure the feature.

History for the Two-Rate Policer Feature

Release	Modification
12.2(4)T	This feature was introduced.
12.2(4)T3	Support for the Cisco 7500 series routers was added.
12.0(26)S	This feature was integrated into Cisco IOS Release 12.0(26)S for the Cisco 7200 and 7500 series routers.
12.2(28)SB	This feature was integrated into Cisco IOS Release 12.2(28)SB.
12.2(33)SRA	This feature was integrated into Cisco IOS Release 12.2(33)SRA.
12.2(33)SXH	This feature was integrated into Cisco IOS Release 12.2(33)SXH.

Finding Support Information for Platforms and Cisco IOS and Catalyst OS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Feature Overview

•Prerequisites

•Configuration Tasks

•Monitoring and Maintaining the Two-Rate Policer

•Configuration Examples

•Additional References

•Command Reference

Feature Overview

Networks police traffic by limiting the input or output transmission rate of a class of traffic based on user-defined criteria. Policing traffic allows you to control the maximum rate of traffic sent or received on an interface and to partition a network into multiple priority levels or class of service (CoS).

The Two-Rate Policer performs the following functions:

•Limits the input or output transmission rate of a class of traffic based on user-defined criteria.

•Marks packets by setting the IP precedence value, IP differentiated services code point (DSCP) value, Multiprotocol Label Switching (MPLS) experimental value, Quality of Service (QoS) group, ATM Cell Loss Priority (CLP) bit, and the Frame Relay Discard Eligibility (DE) bit.

With the Two-Rate Policer, you can enforce traffic policing according to two separate rates—committed information rate (CIR) and peak information rate (PIR). You can specify the use of these two rates, along with their corresponding values, by using two keywords, cir and pir, of the police command.

The Two-Rate Policer manages the maximum rate of traffic through a token bucket algorithm. The token bucket algorithm can use the user-configured values to determine the maximum rate of traffic allowed on an interface at a given moment in time. The token bucket algorithm is affected by all traffic entering or leaving the interface (depending on the location of the interface on which the Two-Rate Policer is configured) and is useful in managing network bandwidth in cases where several large packets are sent in the same traffic stream.

The token bucket algorithm provides users with three actions for each packet: a conform action, an exceed action, and an optional violate action. Traffic entering the interface with Two-Rate Policer configured is placed in to one of these categories. Within these three categories, users can decide packet treatments. For instance, packets that conform can be configured to be sent, packets that exceed can be configured to be sent with a decreased priority, and packets that violate can be configured to be dropped.

The Two-Rate Policer is often configured on interfaces at the edge of a network to limit the rate of traffic entering or leaving the network. In the most common configurations, traffic that conforms is sent and traffic that exceeds is sent with a decreased priority or is dropped. Users can change these configuration options to suit their network needs.

---

Note Additionally, the Two-Rate Policer enables you to implement Differentiated Services (DiffServ) Assured Forwarding (AF) Per-Hop Behavior (PHB) traffic conditioning. For more information about DiffServ, see the "Implementing DiffServ for End-to-End Quality of Service Overview" module.

---

---

Note Starting with Cisco IOS Release 12.1(5)T, you can police traffic by using the Traffic Policing feature (sometimes referred to as the single-rate policer). The Two-Rate Policer (available with Cisco IOS Release 12.2(4)T) is in addition to the Traffic Policing feature, and it provides additional functionality. For more information about the Traffic Policing feature, see the "Traffic Policing" module

---

Benefits

Bandwidth Management Through Rate Limiting

This feature provides improved bandwidth management through rate limiting. Before this feature was available, you could police traffic with the single-rate Traffic Policing feature. The Traffic Policing feature provided a certain amount of bandwidth management by allowing you to set the peak burst size (be). The Two-Rate Policer supports a higher level of bandwidth management and supports a sustained excess rate. With the Two-Rate Policer, you can enforce traffic policing according to two separate rates—CIR and PIR—specified in bits per second (bps).

Packet Marking Through IP Precedence, DSCP Value, MPLS Experimental Value, and the QoS Group Setting

In addition to rate-limiting, the Two-Rate Policer allows you to independently mark the packet according to whether the packet conforms, exceeds, or violates a specified rate. Packet marking also allows you to partition your network into multiple priority levels or classes of service (CoS).

•Use the Two-Rate Policer to set the IP precedence value, the IP  DSCP value, or the MPLS experimental value for packets that enter the network. Then networking devices within your network can use the this setting to determine how the traffic should be treated. For example, the Weighted Random Early Detection (WRED) feature uses the IP precedence value to determine the probability that a packet will be dropped.

•Use the Two-Rate Policer to assign packets to a QoS group. The router uses the QoS group to determine how to prioritize packets within the router.

If you want to mark traffic but do not want to use the Two-Rate Policer, see the "Marking Network Traffic" module.

Packet Marking for Frame Relay Frames

The Two-Rate Policer allows users to mark the Frame Relay DE bit of the Frame Relay frame. The Frame Relay DE bit is one bit and, therefore, can be set to either 0 or 1. In congested environments, frames that have the DE bit set to 1 are discarded before frames that have the DE bit set to 0.

Packet Marking for ATM Cells

The Two-Rate Policer allows users to mark the ATM CLP bit in ATM cells. The ATM CLP bit is used to prioritize packets in ATM networks. The ATM CLP bit is one bit and, therefore, can be set to either 0 or 1. In congested environments, cells that have the ATM CLP bit set to 1 are discarded before cells that have the ATM CLP bit set to 0.

Restrictions

The following restrictions apply to the Two-Rate Policer:

•On a Cisco 7500 series router, traffic policing can monitor Cisco Express Forwarding (CEF) or Distributed CEF (dCEF) switching paths only. To use the Two-Rate Policer, CEF or dCEF must be configured on both the interface receiving the packet and the interface sending the packet.

•On a Cisco 7500 series router, traffic policing cannot be applied to packets that originated from or are destined to a router.

•Two-rate policing can be configured on an interface, a subinterface, a Frame Relay data-link connection identifier (DLCI), and an ATM permanent virtual circuit (PVC).

•Two-rate policing is not supported on the following interfaces:

–Fast EtherChannel

–PRI

–Any interface on a Cisco 7500 series router that does not support CEF or dCEF

Prerequisites

Supported Platforms

•Cisco 2600 series

•Cisco 3620

•Cisco 3640

•Cisco 7100 series

•Cisco 7200 series

•Cisco 7500 series (VIP-based platform only)

---

Note To use the set-clp-transmit action available with this feature, the Enhanced ATM Port Adapter (PA-A3) is required. Therefore, the set-clp-transmit action is not supported on any platform that does not support the PA-A3 adapter (such as the Cisco 2600 series router, the Cisco 3620 router, and the 3640 router). For more information, see the documentation for your specific router.

---

•On a Cisco 7500 series router, CEF or dCEF must be configured on the interface before you can use the Two-Rate Policer. For additional information on CEF or dCEF, see the "Cisco Express Forwarding Features Roadmap" module.

•To configure the Two-Rate Policer, a traffic class and a service policy must be created, and the service policy must be attached to a specified interface. These tasks are performed using the Modular Quality of Service (QoS) Command-Line Interface (CLI) (MQC). For information on the MQC, see the "Applying QoS Features Using the MQC" module.

Configuration Tasks

See the following sections for configuration tasks for the Two-Rate Policer feature. Each task in the list is identified as either required or optional.

•Configuring the Two-Rate Policer (required)

•Verifying the Two-Rate Policer Configuration (optional)

Configuring the Two-Rate Policer

The Two-Rate Policer is configured in the service policy. To configure the Two-Rate Policer, use the following command in policy-map class configuration mode.

Command	Purpose
Router(config-pmap-c)# police cir cir [bc conform-burst] pir pir [be peak-burst]	Specifies that both the CIR and the PIR are to be used for two-rate traffic policing. The bc and be keywords and their associated arguments (conform-burst and peak-burst, respectively) are optional.

Although not required for configuring the Two-Rate Policer, the command syntax of the police command also allows you to specify the action to be taken on a packet when you enable an optional action argument. The resulting action corresponding to the keyword choices are listed in Table 1.

Table 1 police Command Action Keywords 

Keyword	Resulting Action
drop	Drops the packet.
set-clp-transmit	Sets the ATM CLP bit from 0 to 1 on the ATM cell and sends the packet with the ATM CLP bit set to 1.
set-dscp-transmit new-dscp	Sets the IP DSCP value and sends the packet with the new IP DSCP value setting.
set-frde-transmit	Sets the Frame Relay DE bit from 0 to 1 on the Frame Relay frame and sends the packet with the DE bit set to 1.
set-mpls-exp-transmit	Sets the MPLS experimental bits from 0 to 7 and sends the packet with the new MPLS experimental bit value setting.
set-prec-transmit new-prec	Sets the IP precedence and sends the packet with the new IP precedence value setting.
set-qos-transmit new-qos	Sets the QoS group value and sends the packet with the new QoS group value setting.
transmit	Sends the packet with no alteration.

The Two-Rate Policer works by using a token bucket mechanism. There are currently two types of token bucket algorithms: a single token bucket algorithm (available through the Traffic Policing feature) and a two token bucket algorithm (available through the Two-Rate Policer).

For more information about token bucket mechanisms, see the "Policing and Shaping Overview" module.

Verifying the Two-Rate Policer Configuration

To verify that the Two-Rate Policer is configured on your interface, use the following command in user EXEC or privileged EXEC mode:

Command	Purpose
Router# show policy-map interface	Displays statistics and configurations of all input and output policies attached to an interface.

Troubleshooting Tips

•Check the interface type. Verify that your interface is not listed as a nonsupported interface in the Restrictions section of this module.

•For input traffic policing on a Cisco 7500 series router, verify that CEF or dCEF is configured on the interface on which traffic policing is configured.

•For output traffic policing on a Cisco 7500 series router, ensure that the incoming traffic is CEF-switched or dCEF-switched. Traffic policing cannot be used on the switching path unless CEF or dCEF switching is enabled.

Monitoring and Maintaining the Two-Rate Policer

To monitor and maintain the Two-Rate Policer, use the following user EXEC or privileged EXEC mode commands.

Command	Purpose
Router# show policy-map	Displays all configured policy maps.
Router# show policy-map policy-map-name	Displays the user-specified policy map.
Router# show policy-map interface	Displays statistics and configurations of all input and output policies that are attached to an interface.

Configuration Examples

This section provides the following configuration example:

•Limiting the Traffic Using a Policer Class: Example

Limiting the Traffic Using a Policer Class: Example

In this example, the Two-Rate Policer is configured on a class to limit traffic to an average committed rate of 500 kbps and a peak rate of 1 Mbps.

Router(config)# class-map police

Router(config-cmap)# match access-group 101

Router(config-cmap)# policy-map policy1

Router(config-pmap)# class police

Router(config-pmap-c)# police cir 500000 bc 10000 pir 1000000 be 10000 conform-action 
transmit exceed-action set-prec-transmit 2 violate-action drop

Router(config)# interface serial3/0

Router(config-if)# service-policy output policy1

Router(config-if)# end

Router# show policy-map policy1

 Policy Map policy1

  Class police

   police cir 500000 conform-burst 10000 pir 1000000 peak-burst 10000 conform-action 
transmit exceed-action set-prec-transmit 2 violate-action drop

Traffic marked as conforming to the average committed rate (500 kbps) will be sent as is. Traffic marked as exceeding 500 kbps, but not exceeding 1 Mbps, will be marked with IP Precedence 2 and then sent. All traffic exceeding 1 Mbps will be dropped. The burst parameters are set to 10000 bytes.

In the following example, 1.25 Mbps of traffic is sent ("offered") to a policer class.

Router# show policy-map interface serial3/0

 Serial3/0

  Service-policy output: policy1

   Class-map: police (match all)

    148803 packets, 36605538 bytes

    30 second offered rate 1249000 bps, drop rate 249000 bps

    Match: access-group 101

    police:

     cir 500000 bps, conform-burst 10000, pir 1000000, peak-burst 100000

     conformed 59538 packets, 14646348 bytes; action: transmit

     exceeded 59538 packets, 14646348 bytes; action: set-prec-transmit 2

     violated 29731 packets, 7313826 bytes; action: drop

     conformed 499000 bps, exceed 500000 bps violate 249000 bps

   Class-map: class-default (match-any)

    19 packets, 1990 bytes

    30 seconds offered rate 0 bps, drop rate 0 bps

    Match: any

The Two-Rate Policer marks 500 kbps of traffic as conforming, 500 kbps of traffic as exceeding, and 250 kbps of traffic as violating the specified rate. Packets marked as conforming will be sent as is, and packets marked as exceeding will be marked with IP Precedence 2 and then sent. Packets marked as violating the specified rate are dropped.

Additional References

The following sections provide references related to the Two-Rate Policer feature.

Related Documents

Related Topic	Document Title
MQC	•"Applying QoS Features Using the MQC" module
QoS features such as class-based weighted fair queueing (CBWFQ), traffic marking, and traffic policing	•"Configuring Weighted Fair Queueing" module •"Marking Network Traffic" module •"Traffic Policing" module

Standards

Standard	Title
None	—

MIBs

MIB	MIBs Link
•CISCO-CLASS-BASED-QOS-MIB •CISCO-CLASS-BASED-QOS-CAPABILITY-MIB	To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs

RFCs

RFC	Title
RFC 2698	A Two Rate Three Color Marker

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport

Command Reference

This feature uses no new or modified commands.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0809R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2007 Cisco Systems, Inc. All rights reserved.