Cisco IOS Security Configuration Guide: Securing the Data Plane, Release 12.4

Inspection of Router-Generated Traffic

The Inspection of Router-Generated Traffic feature allows Context-Based Access Control (CBAC) to inspect traffic that is originated by or destined to the router on which CBAC is configured. Previously, inspection of TCP, UDP, and H.323 connections initiated by or destined to the router were allowed.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Inspection of Router-Generated Traffic" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for Inspection of Router-Generated Traffic

•Restrictions for Inspection of Router-Generated Traffic

•Information About Inspection of Router-Generated Traffic

•How to Configure Inspection of Router-Generated Traffic

•Configuration Examples for Inspection of Router-Generated Traffic

•Additional References

•Feature Information for Inspection of Router-Generated Traffic

Prerequisites for Inspection of Router-Generated Traffic

•Configure CBAC.

•Configure Cisco Call Manager Express (CCME) or H.323 Gateway to configure the inspection of H.323 connections to and from the router.

Restrictions for Inspection of Router-Generated Traffic

•Inspection of router-generated traffic is supported only on the following protocols: H.323, TCP, and UDP.

•The Cisco IOS Firewall supports only Version 2 of the H.323 protocol. If CCME or the H.323 Gateway has inspection of H.323 router traffic enabled, enter the following commands so that it is configured to support only Version 2 features:

voice service voip

h323

session transport tcp calls-per-connection 1

h245 tunnel disable

h245 caps mode restricted

h225 timeout tcp call-idle value 0

Information About Inspection of Router-Generated Traffic

•CBAC

•Inspection of Router-Generated Traffic Overview

CBAC

CBAC is a Cisco IOS Firewall set feature that provides network protection by using the following functions:

•Traffic Filtering

•Traffic Inspection

•Alerts and Audit Trails

•Intrusion Detection

Traffic Filtering

CBAC filters TCP and UDP packets based on application-layer protocol session information. You can configure CBAC to permit specified TCP and UDP traffic through a firewall only when the connection is initiated from within the network you want to protect. CBAC can inspect traffic for sessions that originate from either side of the firewall, and CBAC can be used for intranet, extranet, and Internet perimeters of your network.

Traffic Inspection

CBAC inspects traffic that travels through the firewall to discover and manage state information for TCP and UDP sessions. This state information is used to create temporary openings in the firewall's access lists to allow return traffic and additional data connections for permissible sessions.

Alerts and Audit Trails

CBAC generates real-time alerts and audit trails. Enhanced audit trail features use SYSLOG to track all network transactions; it records time stamps, the source host, the destination host, the ports used, and the total number of transmitted bytes, for advanced, session-based reporting. Real-time alerts send SYSLOG error messages to central management consoles upon detecting suspicious activity.

Using CBAC inspection rules, you can configure alerts and audit trail information on a per-application protocol basis. For example, if you want to generate audit trail information for HTTP traffic, you can specify that in the CBAC rule covering HTTP inspection.

Intrusion Detection

CBAC provides a limited amount of intrusion detection to protect against specific Simple Mail Transfer Protocol (SMTP) attacks. With intrusion detection, SYSLOG messages are reviewed and monitored for specific "attack signatures." Certain types of network attacks have specific characteristics, or signatures. When CBAC detects an attack, it resets the offending connections and sends SYSLOG information to the SYSLOG server.

Inspection of Router-Generated Traffic Overview

Inspection of Router-Generated Traffic enhances CBAC's functionality to inspect TCP, UDP, and H.323 connections that have a router or firewall as one of the connection endpoints. This enables CBAC to open pinholes for TCP, UDP, and H.323 control channel connections to and from the router, and to open pinholes for data and media channels negotiated over the H.323 control channels.

Inspection of TCP and UDP channels initiated from the router enables dynamic opening of pinholes on the interface access control list (ACL) to allow return traffic. You do not have to modify the ACL when a TCP connection such as Telnet is made from the router.

Inspection of local H.323 connections enables the deployment of CCME, H.323 gateway, and the Cisco IOS Firewall on the same router. This also simplifies ACL configuration on CCME's interface through which H.323 connections are made. Before this feature, in addition to configuring ACLs to allow H.323 connections on a standard port (for example, port 1720), you had to configure ACLs to allow all dynamically negotiated data and media channels. With this feature you just configure the ACLs to allow H.323 control channels on port 1720. The Cisco IOS Firewall inspects all the traffic on the control channel and opens pinholes to allow dynamically negotiated data and media channels.

To enable Inspection of Router-Generated Traffic, specify the router-traffic keyword in the ip inspect name command of the appropriate protocol. This allows inspection of traffic to the router and the traffic passing through the router..

How to Configure Inspection of Router-Generated Traffic

•Configuring H.323 Inspection (required)

•Configuring CBAC (required)

•Verifying the CBAC Configuration (optional)

Configuring H.323 Inspection

To configure the H.323 protocol, perform the following task.

SUMMARY STEPS

1. enable

2. configure terminal

3. ip inspect name inspection-name {TCP | UDP | H323} [alert {on | off}] [audit-trail {on | off}][router-traffic][timeout seconds]

4. interface type slot/port

5. exit

DETAILED STEPS

Configuring CBAC

To configure CBAC, perform the following task.

SUMMARY STEPS

1. enable

2. configure terminal

3. access-list access-list-number {deny | permit} source [source-wildcard] [log]

4. ip inspect name inspection-name {TCP | UDP | H323} [alert {on | off}] [audit-trail {on | off}][router-traffic][timeout seconds]

5. interface type slot/port

6. ip inspect inspection-name {in | out}

7. exit

DETAILED STEPS

Verifying the CBAC Configuration

To verify the CBAC configuration, perform the following task.

SUMMARY STEPS

1. show ip inspect name inspection-name

2. show ip inspect config

3. show ip inspect interfaces

4. show ip inspect session [detail]

5. show ip inspect all

DETAILED STEPS

Step 1 show ip inspect name inspection-name

Use this command to show a particular configured inspection rule. The following example configures the inspection rule myinspectionrule. The output shows the protocols that should be inspected by CBAC and the corresponding idle timeouts for each protocol.

Router# show ip inspect name myinspectionrule

Inspection Rule Configuration

 Inspection name myinspectionrule

  tcp timeout 3600

  udp timeout 30

  ftp timeout 3600

Step 2 show ip inspect config

Use this command to show the CBAC configuration, including global timeouts, thresholds, and inspection rules.

Router# show ip inspect config 

Session audit trail is disabled

one-minute (sampling period) thresholds are [400:500] connections

max-incomplete sessions thresholds are [400:500]

max-incomplete tcp connections per host is 50. Block-time 0 minute.

tcp synwait-time is 30 sec -- tcp finwait-time is 5 sec

tcp idle-time is 3600 sec -- udp idle-time is 30 sec

dns-timeout is 5 sec

 Inspection Rule Configuration

  inspection name myinspectionrule

  tcp timeout 3600

  udp timeout 30

  ftp timeout 3600

Step 3 show ip inspect interfaces

Use this command to show the interface configuration with respect to applied inspection rules and access lists.

Router# show ip inspect interfaces 

Interface Configuration

 Interface Ethernet0

  Inbound inspection rule is myinspectionrule

    tcp timeout 3600

    udp timeout 30

    ftp timeout 3600

  Outgoing inspection rule is not set

  Inbound access list is not set

  Outgoing access list is not set

Step 4 show ip inspect session detail

Use this command to display existing sessions that CBAC is currently tracking and inspecting. The following sample output shows that an outgoing ACL and an inbound ACL (dynamic ACLs) have been created to allow return traffic.

Router# show ip inspect session detail 

Established Sessions

 Session 80E87274 (192.168.1.116:32956)=>(192.168.101.115:23) tcp SIS_OPEN

   Created 00:00:08, Last heard 00:00:04

   Bytes sent (initiator:responder) [140:298] acl created 2

   Outgoing access-list 102 applied to interface FastEthernet0/0

   Inbound access-list 101 applied to interface FastEthernet0/1

Step 5 show ip inspect all

Use this command to show all CBAC configuration and all existing sessions that are currently being tracked and inspected by CBAC.

Router# show ip inspect all 

Session audit trail is disabled

one-minute (sampling period) thresholds are [400:500] connections

max-incomplete sessions thresholds are [400:500]

max-incomplete tcp connections per host is 50. Block-time 0 minute.

tcp synwait-time is 30 sec -- tcp finwait-time is 5 sec

tcp idle-time is 3600 sec -- udp idle-time is 30 sec

dns-timeout is 5 sec

Inspection Rule Configuration

 Inspection name all

    tcp timeout 3600

    udp timeout 30

    ftp timeout 3600

Interface Configuration

 Interface Ethernet0

  Inbound inspection rule is all

    tcp timeout 3600

    udp timeout 30

    ftp timeout 3600

  Outgoing inspection rule is not set

  Inbound access list is not set

  Outgoing access list is not set

 Established Sessions

 Session 25A6E1C (30.0.0.1:46065)=>(40.0.0.1:21) ftp SIS_OPEN

 Session 25A34A0 (40.0.0.1:20)=>(30.0.0.1:46072) ftp-data SIS_OPEN

Configuration Examples for Inspection of Router-Generated Traffic

•Example: Configuring CBAC with Inspection of H.323 Traffic

Example: Configuring CBAC with Inspection of H.323 Traffic

These commands create the ACL. In this example, TCP traffic from subnet 100.168.11.1, 192.168.11.50, and 192.168.100.1 is permitted.

access-list 120 permit tcp host 100.168.11.1 any eq 1720

access-list 121 permit tcp host 192.168.11.50 host 100.168.11.1 eq 1720

access-list 121 permit tcp host 192.168.100.1 host 100.168.11.1 eq 1720

These commands create the CBAC inspection rule LOCAL-H323, allowing inspection of the protocol traffic specified by the rule. This inspection rule sets the timeout value to 180 seconds for each protocol (except for RPC). The timeout value defines the maximum time that a connection for a given protocol can remain active without any traffic passing through the router. When these timeouts are reached, the dynamic ACLs that are inserted to permit the returning traffic are removed, and subsequent packets (possibly even valid ones) are not permitted.

ip inspect name LOCAL-H323 tftp timeout 180

ip inspect name LOCAL-H323 h323 router-traffic timeout 180

These commands apply the inspection rule and ACL. In this example, the inspection rule LOCAL-H323 is applied to traffic at interface Serial0/3/0.

interface Serial0/3/0

 ip address 11.168.11.2 255.255.255.0

 ip access-group 121 in

 ip access-group 120 out

 ip inspect LOCAL-H323 in

 ip inspect LOCAL-H323 out

 encapsulation frame-relay

frame-relay map ip 11.168.11.1 168 broadcast

 no frame-relay inverse-arp

 frame-relay intf-type dce

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for Inspection of Router-Generated Traffic

Table 1 lists the features in this module and provides links to specific configuration information.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2009—2010 Cisco Systems, Inc. All rights reserved.