Table Of Contents

Configuration Examples

Cisco 2600 Series Router Configuration Example

Cisco 3631 Router Configuration Example

Cisco 3725 Router Configuration Example

1-Port ADSL WAN Interface Card Configuration Examples

VoATM over AAL2 on the ATM Interface Configuration Example

VoATM over AAL5 on the ATM Interface Configuration Example

NM-AIC-64, Contact Closure NetworkConfiguration Examples

AIC IP Address Configuration Example

IP Route to the AIC Configuration Examples

With an Unnumbered IP Address

Without an Unnumbered IP Address

AIC CLI Configuration for Alarms

Discrete Alarm

Analog Alarm Monitoring Current

Analog Alarm Monitoring Current Configured as a Discrete

Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

Configuration in CPE Mode Example

Configuration in CO Mode Example

Configuration Examples

---

This appendix shows some examples of the configuration in the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers.

---

Note The MTU size for the NM-1GE module cannot be set to support jumbo frames on the Cisco 2691, Cisco 3725, or Cisco 3725 routers.

---

Cisco 2600 Series Router Configuration Example

Following is an example of a configuration on a Cisco 2600 series router.

The following configuration command script was created:

hostname 2600

enable secret 5 $1$zxxT$YZMzUP1/wQvyLn5cWeyPu.

enable password guessme

line vty 0 4

password guessagain

snmp-server community public

!

no appletalk routing

no decnet routing

ip routing

no clns routing

no ipx routing

no vines routing

no xns routing

no apollo routing

no bridge 1

!

line 1 64

speed 115200

flowcontrol hardware

login local

autoselect during-login

autoselect ppp

modem dialin

ip local pool setup_pool 172.20.30.40 172.20.30.88

!

username user password passwd

line 1 64

modem output

transport input all

!

interface Ethernet0/0

no shutdown

ip address 255.255.255.0 255.255.0.0

lat enabled

no mop enabled

!

interface Serial0/0

encapsulation hdlc

clock rate 2000000

ip address 1.0.0.1 255.0.0.0

lat enabled

appletalk cable-range 3-3 3.3

appletalk zone myzone

ipx network 8

no vines metric

mop enabled

!

interface Ethernet0/1

ip address 255.255.255.1 255.255.0.0

lat enabled

no vines metric

mop enabled

!

interface Serial0/1

physical-layer sync

encapsulation ppp

ip address 2.0.0.1 255.0.0.0

lat enabled

appletalk cable-range 6-6 6.6

appletalk zone myzone

ipx network 6

no vines metric

xns network 7

mop enabled

!

interface Serial0/2

physical-layer async

ip address 3.0.0.1 255.0.0.0

lat enabled

appletalk cable-range 8-8 8.8

appletalk zone myzone

ipx network 8

no vines metric

mop enabled

!

interface Serial1/0

physical-layer sync

encapsulation frame-relay

frame-relay lmi-type cisco

clock rate 115200

ip address 4.0.0.1 255.0.0.0

no lat enabled

no vines metric

no mop enabled

!

interface Serial1/1

physical-layer async

ip address 5.0.0.1 255.0.0.0

no lat enabled

no vines metric

no mop enabled

!

interface Serial1/2

physical-layer sync

encapsulation x25 dte

x25 address 1234

x25 map ip 1.0.0.1 4321

x25 map ipx 6.0.0.1 -2132065964

x25 ltc 1

x25 htc 64

x25 win 7

x25 wout 7

x25 threshold 2

x25 ips 128

x25 ops 128

clock rate 115200

ip address 6.0.0.1 255.0.0.0

no lat enabled

no vines metric

no mop enabled

!

interface Serial1/3

physical-layer sync

encapsulation smds

smds address c141.5556.1415

no keepalive

smds static-map ip 2.0.0.1 c141.5556.1414

smds static-map ipx 2.0.0.1 c141.5556.1414

clock rate 115200

ip address 172.22.50.10 255.255.0.0

no lat enabled

no vines metric

no mop enabled

dialer-list 1 protocol ip permit

dialer-list 1 protocol ipx permit

!

router igrp 1

redistribute connected

network 172.21.0.0

!

end

Following is an example of a configuration on the Cisco 2691 router.

C2691#show running-config

Building configuration...

Current configuration : 1143 bytes

!

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname C2691

!

enable password lab

!

voice-card 1

!

ip subnet-zero

!

!

no ip domain-lookup

ip host rtplab-dev 172.18.207.10

!         

!         

!         

!         

fax interface-type fax-mail

mta receive maximum-recipients 0

!         

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 1 timeslots 1-24 type e&m-wink-start

!         

controller T1 1/1

 framing sf

 linecode ami

!         

!         

!         

!         

interface FastEthernet0/0

 ip address 172.18.193.171 255.255.255.0

 speed 100

 full-duplex

!         

interface FastEthernet0/1

 ip address 50.0.0.4 255.0.0.0

 speed 100

 full-duplex

!         

ip classless

ip route 172.18.207.0 255.255.255.0 172.18.193.1

ip http server

ip pim bidir-enable

!         

!         

!         

call rsvp-sync

!         

voice-port 1/0:1

 output attenuation 3

!         

!         

mgcp profile default

!         

dial-peer cor custom

!         

!         

!         

dial-peer voice 919 pots

 destination-pattern 919

 port 1/0:1

 prefix 919

!         

dial-peer voice 408 voip

 destination-pattern 408

 session target ipv4:50.0.0.3

 dtmf-relay h245-alphanumeric

 codec g711alaw

!         

!         

line con 0

 exec-timeout 0 0

line aux 0

line vty 0 4

 password lab

 login    

!         

end       

Following is an example of a configuration on the Cisco 2620XM router:

Building configuration...

Current configuration : 588 bytes

!

version 12.2

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname c2620xm

!

!

ip subnet-zero

!

!

!

!

!

!

!

!

!

!

fax interface-type fax-mail

mta receive maximum-recipients 0

!         

!         

!         

!         

interface FastEthernet0/0

 ip address 111.0.0.29 255.255.255.0

 duplex auto

 speed auto

 no cdp enable

!         

ip classless

ip route 0.0.0.0 0.0.0.0 FastEthernet0/0

no ip http server

ip pim bidir-enable

!         

!         

no cdp run

!         

!         

call rsvp-sync

!         

!         

mgcp profile default

!         

dial-peer cor custom

!         

!         

!         

!         

line con 0

line aux 0

line vty 0 4

 login    

!         

!         

end 

Cisco 3631 Router Configuration Example

Following is an example of the configuration on the Cisco 3631 router equipped with the following modules:

•IMA-8T1 in

•NM-4A/S

•WIC-2A/S

•WIC-1DSU-56k4

Building configuration...

00:45:06: %SYS-5-CONFIG_I: Configured from console by console 

Current configuration : 3095 bytes 

! 

! Last configuration change at 12:12:59 PDT Tue Dec 4 2001 

! NVRAM config last updated at 12:12:26 PDT Tue Dec 4 2001 

! 

version 12.2

service timestamps debug uptime 

service timestamps log uptime 

service password-encryption 

! 

hostname cisco3631 

! 

enable secret 5 $1$6UL.$w0aJJ5oZmIv1zRDl1RMvo/ 

! 

username USER password 7 01030717481C091D25 

memory-size iomem 10 

clock timezone PDT -8 

ip subnet-zero 

no ip domain-lookup 

! 

x29 profile linemode 2:1 3:2 15:1 

x25 routing 

! 

chat-script test "" "ATDT\T" TIMEOUT 120 CONNECT \c 

! 

! 

! 

! 

! 

! 

! 

! 

! 

! 

! 

interface FastEthernet0/0 

description FAST ETHERNET INTERFACE 

ip address x.x.x.x x.x.x.x 

duplex auto 

speed auto 

! 

interface Serial0/0 

description WIC-1DSU-56k4 

ip address x.x.x.x x.x.x.x 

encapsulation ppp

! 

interface Serial0/1 

description WIC-2A/S 

physical-layer async 

no ip address 

encapsulation ppp 

dialer in-band 

dialer rotary-group 3 

dialer-group 1 

async mode dedicated 

no fair-queue 

! 

interface Serial0/2 

description WIC-2A/S 

physical-layer async 

no ip address 

encapsulation ppp 

no ip route-cache 

no ip mroute-cache 

dialer in-band 

dialer rotary-group 3 

dialer-group 1 

async default routing 

async mode dedicated 

no fair-queue 

! 

interface Serial1/0 

description NM-4A/S 

no ip address 

encapsulation x25 

x25 htc 8 

! 

interface Serial1/1 

description NM-4A/S 

no ip address 

encapsulation x25 dce 

x25 ips 256 

x25 ops 256 

clockrate 9600 

! 

interface Serial1/2 

no ip address 

shutdown 

! 

interface Serial1/3 

no ip address 

shutdown 

! 

interface ATM2/0 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/1 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/2 

description ATM T1 

ip address x.x.x.x x.x.x.x 

no ip route-cache 

no ip mroute-cache 

no atm ilmi-keepalive 

pvc atm71 0/71 

protocol clns 47.0004.004d.0056.0000.0c00.0003.00 broadcast 

protocol ip 12.0.0.2 broadcast 

encapsulation aal5snap 

! 

scrambling-payload 

impedance 120-ohm

! 

interface ATM2/3 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/4 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/5 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/6 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/7 

no ip address 

shutdown 

no atm ilmi-keepalive 

no scrambling-payload 

! 

interface ATM2/IMA0 

description ATM-IMA GROUP 

ip address x.x.x.x x.x.x.x 

no ip route-cache 

no ip mroute-cache 

no atm ilmi-keepalive 

pvc atm71 0/71 

protocol clns 47.0004.004d.0056.0000.0c00.0002.00 broadcast 

protocol ip 12.0.0.1 broadcast 

encapsulation aal5snap 

! 

interface Dialer3 

ip address x.x.x.9 x.x.x.x 

encapsulation ppp 

no ip route-cache 

no ip mroute-cache 

dialer in-band 

dialer idle-timeout 500 

dialer map ip x.x.x.10 name USER modem-script test broadcast 

9,5551122 

dialer map ip x.x.x.10 name USER modem-script test broadcast 

9,5551123 

dialer hold-queue 15 

dialer load-threshold 5 either 

dialer-group 1 

no fair-queue 

no cdp enable 

ppp authentication chap 

ppp multilink 

group-range 4 5 

! 

router ospf 1 

redistribute connected subnets 

network X.X.X.X 0.0.0.X area 3 

! 

! 

ip classless 

no ip http server 

ip pim bidir-enable 

! 

! 

! 

! 

! 

! 

! 

! 

! 

! 

! 

! 

snmp-server view cutdown internet included 

snmp-server view cutdown at excluded 

snmp-server community public view cutdown RO 

snmp-server community private view cutdown RW 

! 

call rsvp-sync 

! 

! 

mgcp profile default 

! 

dial-peer cor custom 

! 

! 

! 

! 

line con 0 

line 3 

modem InOut 

transport input all 

autohangup 

stopbits 1 

rxspeed 115200 

txspeed 115200 

flowcontrol hardware 

line 5 

modem InOut 

transport input all 

autohangup 

stopbits 1 

rxspeed 115200 

txspeed 115200 

flowcontrol hardware 

line 6 

line aux 0 

password 7 08314D5D1A0E0A0516 

login 

modem InOut 

transport input all 

line vty 0 4 

password 7 00141215174C04140B 

login 

! 

end

Cisco 3725 Router Configuration Example

Following example shows the configurationon the Cisco 3725 router.

version 12.1 

no service single-slot-reload-enable 

service timestamps debug uptime 

service timestamps log uptime 

no service password-encryption 

! 

hostname pipertdm 

! 

no logging buffered 

logging rate-limit console 10 except errors 

no logging console 

! 

! 

! 

ip subnet-zero 

! 

! 

no ip finger 

ip host rtplab-tftp2 172.18.207.16 

ip host rtplab-dev 172.18.207.10 

! 

no ip dhcp-client network-discovery 

no mgcp timer receive-rtcp 

call rsvp-sync 

! 

! 

! 

! 

! 

fax interface-type modem 

mta receive maximum-recipients 0 

! 

! 

! 

! 

interface FastEthernet0/0 

ip address 172.18.197.74 255.255.255.252 

no keepalive 

duplex auto 

speed auto 

no cdp enable 

! 

interface FastEthernet0/1 

ip address 2.2.2.2 255.0.0.0 

no keepalive 

duplex auto 

speed auto 

no cdp enable 

! 

interface BRI1/0 

no ip address 

shutdown 

! 

interface FastEthernet1/0 

ip address 1.1.1.1 255.0.0.0 

no keepalive 

duplex auto 

speed auto 

no cdp enable 

! 

interface Serial1/0 

no ip address 

shutdown 

no fair-queue 

clockrate 125000 

! 

interface FastEthernet1/1 

ip address 3.3.3.3 255.0.0.0 

no keepalive 

shutdown 

duplex auto 

speed auto 

no cdp enable 

! 

interface Serial1/1 

no ip address 

shutdown 

clockrate 125000 

! 

ip kerberos source-interface any 

ip classless 

ip route 172.18.0.0 255.255.0.0 FastEthernet0/0 

ip http server 

! 

! 

! 

! 

snmp-server packetsize 4096 

snmp-server chassis-id 

snmp-server manager 

! 

! 

dial-peer cor custom 

! 

! 

! 

! 

line con 0 

exec-timeout 0 0 

transport input none 

line 1 32 

line 35 96 

line aux 0 

line vty 0 4 

! 

end

1-Port ADSL WAN Interface Card Configuration Examples

Following configuration examples are shown below:

•VoATM over AAL2 on the ATM Interface Configuration Example

•VoATM over AAL5 on the ATM Interface Configuration Example

VoATM over AAL2 on the ATM Interface Configuration Example

The following example shows VoATM over AAL2 on the ATM interface with an ADSL card:

Router# 

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname host1

!

memory-size iomem 10

voice-card 1

!

ip subnet-zero

ip host host2 225.255.255.224

!

no mgcp timer receive-rtcp

call rsvp-sync

!

!

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 0 timeslots 1 type e&m-wink-start

 ds0-group 1 timeslots 2 type e&m-wink-start

.

.

.

ds0-group 23 timeslots 24 type e&m-wink-start

!

controller T1 1/1

 framing esf

 linecode b8zs

!

interface Ethernet0/0

 ip address 1.6.46.119 255.255.255.224

 half-duplex

 no cdp enable

!

interface Serial0/0

 no ip address

 shutdown

!

interface ATM0/1

 ip address 10.1.1.1 255.0.0.0

 load-interval 30

 atm vc-per-vp 256

 no atm ilmi-keepalive

 pvc 10/100 

  vbr-rt 672 672 512

  encapsulation aal2

 !

 pvc 10/200 

  protocol ip 10.1.1.2 broadcast

  encapsulation aal5snap

 !

 dsl operating-mode ansi-dmt

 no fair-queue

!

interface Ethernet0/1

 no ip address

 shutdown

!

ip classless

ip route 223.255.254.254 255.255.255.224 Ethernet0/0

no ip http server

!

!

snmp-server engineID local 000000090200003080477F20

snmp-server manager

!

voice-port 1/0:0

 local-alerting

 timeouts wait-release 3

 connection trunk 3001 

!

voice-port 1/0:1

 local-alerting

 timeouts wait-release 3

 connection trunk 3002 

.

.

.

voice-port 1/0:23

 local-alerting

 timeouts wait-release 3

 connection trunk 3024 

 shutdown

!

dial-peer cor custom

!

dial-peer voice 3001 voatm

 destination-pattern 3001

 called-number 4001

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 31

 codec aal2-profile ITUT 1 g711ulaw

 no vad

!

dial-peer voice 3002 voatm

 destination-pattern 3002

 called-number 4002

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 32

 codec aal2-profile custom 100 g726r32

 no vad

!

dial-peer voice 3003 voatm

 destination-pattern 3003

 called-number 4003

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 33

 codec aal2-profile ITUT 7 g729abr8

 no vad

.

.

.

dial-peer voice 3024 voatm

 destination-pattern 3024

 called-number 3024

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 54

 codec aal2-profile ITUT 7 g729abr8

 no vad

!

dial-peer voice 1 pots

 destination-pattern 4001

 port 1/0:0

!

dial-peer voice 2 pots

 destination-pattern 4002

 port 1/0:1

.

.

.

dial-peer voice 24 pots

 destination-pattern 4024

 port 1/0:23

!

line con 0

 exec-timeout 0 0

 transport input none

line aux 0

line vty 0 4

 login

!

no scheduler allocate

end

VoATM over AAL5 on the ATM Interface Configuration Example

The following example shows a Cisco 2600 series router configured for VoATM over AAL5 on the ATM interface with an ADSL card.

Router#

version 12.2

no service single-slot-reload-enable

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname u2621

!

no logging buffered

no logging buffered

logging rate-limit console 10 except errors

!

memory-size iomem 15

voice-card 1

!

ip subnet-zero

!

no ip finger

no ip domain-lookup

!

no mgcp timer receive-rtcp

call rsvp-sync

!

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 0 timeslots 1-24 type e&m-wink-start

!

controller T1 1/1

!

!

interface ATM0/0

 ip address 12.0.0.1 255.255.255.224

 load-interval 30

 atm vc-per-vp 256

 no atm ilmi-keepalive

 dsl operating-mode auto

 no fair-queue

!

!

interface FastEthernet0/0

 ip address 1.7.73.1 255.255.255.224

 duplex auto

 speed auto

!

!

interface FastEthernet0/1

 ip address 192.168.2.1 255.255.255.224

 load-interval 30

 duplex auto

 speed auto

!

ip classless

ip route 223.255.254.0 255.255.255.224 FastEthernet0/0

no ip http server

!

!

snmp-server engineID local 0000000902000002163DB260

snmp-server packetsize 4096

snmp-server manager

!

voice-port 1/0:0

!

dial-peer cor custom

!

!

dial-peer voice 5 pots

 destination-pattern 777...

 port 1/0:0

 prefix 777

! 

! 

dial-peer voice 100 voatm

 destination-pattern 888....

 session target atm0/0 pvc 0/72

!

!

line con 0

 exec-timeout 0 0

 transport input none

line aux 0

line vty 0 4

 login

!

end

NM-AIC-64, Contact Closure NetworkConfiguration Examples

The following examples are documented below:

•AIC IP Address Configuration Example

•IP Route to the AIC Configuration Examples

–With an Unnumbered IP Address

–Without an Unnumbered IP Address

AIC CLI Configuration for Alarms

AIC IP Address Configuration Example

The following example shows a Cisco 3600 router configured for AIC IP address:

version 12.2

no service single-slot-reload-enable

service tcp-keepalives-in

service tcp-keepalives-out

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname 3600-top

!

logging rate-limit console 10 except errors

!

memory-size iomem 15

ip subnet-zero

!

!

no ip finger

no ip domain-lookup

ip host moe 172.31.10.2

ip host mickey 10.1.1.2

!

no ip dhcp-client network-discovery

frame-relay switching

x25 routing

!

!

call-history-mib max-size 50

!

interface Ethernet0/0

 ip address 10.5.37.13 255.255.0.0

 ip helper-address 223.255.254.254

 no keepalive

 half-duplex

!

interface Serial0/0

 ip address 10.5.5.1 255.255.255.0

 encapsulation frame-relay

 no ip mroute-cache

 clockrate 500000

 frame-relay class voice-vc

 frame-relay traffic-shaping

 frame-relay map ip 10.5.5.2 990 broadcast

 frame-relay interface-dlci 990

 frame-relay intf-type dce

!

interface Ethernet0/1

 no ip address

 half-duplex

 no cdp enable

!

interface Serial0/1

 ip address 10.11.11.1 255.255.255.0

 encapsulation frame-relay

 no ip mroute-cache

 clockrate 256000

 frame-relay class voice-vc

 frame-relay traffic-shaping

 frame-relay interface-dlci 991

 frame-relay intf-type dce

!

interface Serial1/0

 ip address negotiated

!

router mobile

!

ip kerberos source-interface any

ip classless

ip route 223.255.254.254 255.255.255.255 10.5.0.1

ip route 223.255.254.254 255.255.255.255 Ethernet0/0

no ip http server

!

!

map-class frame-relay voice-vc

 frame-relay cir 800000

 frame-relay bc 512000

 no frame-relay adaptive-shaping

 frame-relay fair-queue

 frame-relay voice bandwidth 500000

 frame-relay fragment 100

 frame-relay ip rtp priority 16384 16383 512

!         

map-class frame-relay fr1

 frame-relay cir 1000000

 frame-relay bc 1000

 no frame-relay adaptive-shaping

 frame-relay fair-queue

 frame-relay voice bandwidth 1000000

 frame-relay fragment 100

!

map-class frame-relay voice-vc2

 frame-relay cir 800000

 frame-relay bc 512000

 no frame-relay adaptive-shaping

 frame-relay voice bandwidth 800000

!

map-class frame-relay voice-data

access-list 1 deny   192.200.1.20

access-list 2 deny   10.10.1.10

dialer-list 1 protocol ip permit

dialer-list 1 protocol ipx permit

!

snmp-server packetsize 4096

snmp-server manager

!

alarm-interface 1

 ip address 10.4.3.2

call rsvp-sync

!

mgcp modem passthrough voip mode ca

no mgcp timer receive-rtcp

!

mgcp profile default

!

dial-peer cor custom

!

dial-peer voice 1 pots

 destination-pattern 3

 direct-inward-dial

 forward-digits all

!

dial-peer voice 100 voip

 shutdown

 destination-pattern 3

 session target ipv4:10.2.81.1

 playout-delay maximum 300

!

dial-peer voice 2 pots

 shutdown

 destination-pattern 3002

!

dial-peer voice 3 pots

 shutdown

 destination-pattern 3003

!

dial-peer voice 4 pots

 shutdown

 destination-pattern 3004

!

dial-peer voice 2000 voip

 shutdown

 destination-pattern 2...

 session target ipv4:5.5.5.2

 playout-delay maximum 300

!

dial-peer voice 110 voip

 shutdown 

 destination-pattern 1...

 session target ipv4:10.2.83.30

 playout-delay maximum 300

!

dial-peer voice 922 pots

 shutdown

 destination-pattern 9..

!

dial-peer voice 22 pots

 shutdown

 destination-pattern 22

!

dial-peer voice 6001 pots

 shutdown

 destination-pattern 6001

!

dial-peer voice 333 voip

 shutdown

 destination-pattern 1

 session target ipv4:10.2.79.55

 playout-delay maximum 300

!

dial-peer voice 200 vofr

 shutdown

 destination-pattern 1

!

dial-peer voice 7001 pots

 shutdown

 destination-pattern 7001

!

dial-peer voice 5000 voip

 shutdown

 destination-pattern 5...

 session target ipv4:10.11.11.2

 playout-delay maximum 300

!

dial-peer voice 20 voip

 shutdown

 destination-pattern 1

 session target ipv4:10.11.11.2

 playout-delay maximum 300

!

dial-peer voice 2001 voip

 preference 2

 shutdown

 destination-pattern 2...

 session target ipv4:10.2.79.7

 playout-delay maximum 300

!

dial-peer voice 1000 voip

 destination-pattern 1...

 session target ipv4:10.2.81.6

 playout-delay maximum 300

 no vad

!

dial-peer voice 1001 voatm

 shutdown

 destination-pattern 1...

!

dial-peer voice 1100 vofr

 shutdown

 destination-pattern 1...

 session target Serial0/0 990

 no vad

!

gateway 

!

gateway 

!

gatekeeper

 shutdown

!

!

line con 0

 exec-timeout 0 0

 transport input none

line 33

 no exec

 transport preferred none

 transport input telnet

 transport output none

 stopbits 1

line aux 0

line vty 0 4

 login

!

end

IP Route to the AIC Configuration Examples

Following examples show the configuration of an IP route to the AIC with an unnumbered and numbered IP address.

With an Unnumbered IP Address

The following example shows a Cisco 3660 router, with an IP route to an AIC, is configured with an unnumbered IP address:

version 12.1

no service single-slot-reload-enable

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname uut2-3660

!

logging rate-limit console 10 except errors

no logging console

!

ip subnet-zero

!

!

no ip finger

no ip domain-lookup

!

call rsvp-sync

cns event-service server

!

interface FastEthernet0/0

 ip address 10.2.130.2 255.255.0.0

 duplex auto

 speed auto

no cdp enable

!

interface Serial5/0

 ip unnumbered FastEthernet0/0

!

ip kerberos source-interface any

ip classless

ip route 0.0.0.0 0.0.0.0 10.2.0.1

ip route 10.2.130.102 255.255.255.255 Serial5/0

ip http server

!

no cdp run

!

alarm-interface 5

 ip address 10.2.130.102

!

dial-peer cor custom

!

!

!

line con 0

 exec-timeout 0 0

 transport input none

line 161

 no exec

 transport preferred none

 transport input telnet

 transport output none

 stopbits 1

line aux 0

line vty 0 4

 password lab

 login

!

end

Without an Unnumbered IP Address

The following example shows a Cisco 2621 router configured without an unnumbered IP address:

uut5-2621#s run

Building configuration...

Current configuration :1318 bytes

!

version 12.2

no service single-slot-reload-enable

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname uut5-2621

!

logging rate-limit console 10 except errors

no logging console

!

ip subnet-zero

!

no ip finger

no ip domain-lookup

!         

no ip dhcp-client network-discovery

!

interface FastEthernet0/0

 ip address 10.2.130.5 255.255.0.0

 duplex auto

 speed auto

 no cdp enable

!

interface Serial1/0

 ip address 172.128.12.1 255.255.255.252

!

router rip

 network 10.0.0.0

!

ip kerberos source-interface any

ip classless

ip route 0.0.0.0 0.0.0.0 10.2.0.1

no ip http server

!

no cdp run

!

snmp-server packetsize 4096

snmp-server manager

!

!

alarm-interface 1

 ip address 172.128.12.2

call rsvp-sync

!

dial-peer cor custom

!

line con 0

 exec-timeout 0 0

 transport input none

line 33

 no exec

 transport preferred none

 transport input telnet

 transport output none

 stopbits 1

line aux 0

line vty 0 4

 password lab

 login

!

no scheduler allocate

!

end

AIC CLI Configuration for Alarms

These examples are output from the show alarm config # command.

Discrete Alarm

description:west door

normally closed

normal state description:door closed

alarm state description:door open

SNMP trap:enabled

Analog Alarm Monitoring Current

description:thermostat

high-high state description:very hot

high state description:hot

normal state description:just right

low state description:cold

low-low state description:very cold

current-loop -5.2 5.4 15.0 25.0 35.1 45.6

SNMP trap:enabled

Analog Alarm Monitoring Current Configured as a Discrete

description:east door

configured as discrete

normal state description:door closed

alarm description:door open

current-loop 0.0 3.2 5.9

SNMP trap:enabled

Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

The following configuration allows remote LANs and standalone remote users with modems to dial in to a central site.

The following configuration example shows a Cisco 3640 router with the following hardware configuration:

• One 2-port ISDN-PRI network module installed in slot 1

• One digital modem network module installed in slot 2 and slot 3

• One 1-port Ethernet network module installed in slot 0

---

Note Each MICA digital modem card has its own group async configuration. Additionally, a single range of async lines is used for each modem card. For additional interface numbering information, refer to the Digital Modem Network Module Configuration Note.

---

!

version 11.2

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

no service udp-small-servers

no service tcp-small-servers

!

hostname NAS

!

aaa new-model

aaa authentication login default local

aaa authentication login console enable

aaa authentication login vty local

aaa authentication login dialin local

aaa authentication ppp default local

aaa authentication ppp dialin if-needed local

enable secret cisco

!

username admin password cisco

username remotelan1 password dialpass1

username remotelan2 password dialpass2

username PCuser1 password dialpass3

username PCuser2 password dialpass4

async-bootp dns-server 10.1.3.1 10.1.3.2

isdn switch-type primary-5ess

!

controller T1 1/0

 framing esf

 clock source line 

 linecode b8zs

 pri-group timeslots 1-24

!

controller T1 1/1

 framing esf

 clock source line 

 linecode b8zs

 pri-group timeslots 1-24

!

interface Loopback0

 ip address 10.1.2.254 255.255.255.0

!

interface Ethernet0/0

 ip address 10.1.1.10 255.255.255.0

 ip summary address eigrp 10 10.1.2.0 255.255.255.0

!

interface Serial 1/0:23

 no ip address

 encapsulation ppp

 no keepalive

 isdn incoming-voice modem

 dialer rotary-group 0

 dialer-group 1

 no fair-queue

 no cdp enable

!

interface Serial 1/1:23

 no ip address

 encapsulation ppp

 no keepalive

 isdn incoming-voice modem

 dialer rotary-group 0

 dialer-group 1

 no fair-queue

 no cdp enable

!

interface Group-Async1

 ip unnumbered Loopback0

 encapsulation ppp

 async mode interactive

 peer default ip address pool dialin_pool

 no cdp enable

 ppp authentication chap pap dialin

 group-range 65 88

!

interface Group-Async2

 ip unnumbered Loopback0

 encapsulation ppp

 async mode interactive

 peer default ip address pool dialin_pool

 no cdp enable

 ppp authentication chap pap dialin

 group-range 97 120

!

interface Dialer0

 ip unnumbered Loopback0

 no ip mroute-cache

 encapsulation ppp

 peer default ip address pool dialin_pool

 dialer in-band

 dialer-group 1

 no fair-queue

 no cdp enable

 ppp authentication chap pap dialin

 ppp multilink

!

router eigrp 10

 network 10.0.0.0

 passive-interface Dialer0

 no auto-summary

!

ip local pool dialin_pool 10.1.2.1 10.1.2.50

ip default-gateway 10.1.1.1

ip classless

!

dialer-list 1 protocol ip permit

!

line con 0

 login authentication console

line 65 88

 autoselect ppp

 autoselect during-login

 login authentication dialin

 modem DialIn

line 97 120

 autoselect ppp

 autoselect during-login

 login authentication dialin

 modem DialIn

line aux 0

 login authentication console

line vty 0 4

 login authentication vty

 transport input telnet rlogin

!

end

Configuration in CPE Mode Example

The following example shows a G.SHDSL configuration of VoATM over AAL2, operating in customer premises equipment (CPE) mode, on a Cisco 2600 series router. This router in CPE mode can be linked to either a DSLAM or to another router that is configured to operate in central office (CO) mode.

Router#

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname host1

!

memory-size iomem 10

voice-card 1

!

ip subnet-zero

ip host host2 225.255.255.224

!

no mgcp timer receive-rtcp

call rsvp-sync

!

!

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 0 timeslots 1 type e&m-wink-start

 ds0-group 1 timeslots 2 type e&m-wink-start

.

.

.

ds0-group 23 timeslots 24 type e&m-wink-start

!

controller T1 1/1

 framing esf

 linecode b8zs

!

interface Ethernet0/0

 ip address 209.165.202.128 255.255.255.224

 half-duplex

 no cdp enable

!

interface Serial0/0

 no ip address

 shutdown

!

interface ATM0/1

 ip address 209.165.201.1 255.255.255.224

 dsl operating-mode gshdsl symmetric annex A

 dsl equipment-type cpe

 dsl linerate auto

 load-interval 30

 atm vc-per-vp 256

 no atm ilmi-keepalive

 pvc 10/100 

  vbr-rt 672 672 512

  encapsulation aal2

 !

 pvc 10/200 

  protocol ip 209.165.202.159 broadcast

  encapsulation aal5snap

 !

 no fair-queue

!

interface Ethernet0/1

 no ip address

 shutdown

!

ip classless

ip route 209.165.202.128 255.255.255.224 Ethernet0/0

no ip http server

!

!

snmp-server engineID local 000000090200003080477F20

snmp-server manager

!

voice-port 1/0:0

 local-alerting

 timeouts wait-release 3

 connection trunk 3001 

!

voice-port 1/0:1

 local-alerting

 timeouts wait-release 3

 connection trunk 3002 

.

.

.

voice-port 1/0:23

 local-alerting

 timeouts wait-release 3

 connection trunk 3024 

 shutdown

!

dial-peer cor custom

!

dial-peer voice 3001 voatm

 destination-pattern 3001

 called-number 4001

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 31

 codec aal2-profile ITUT 1 g711ulaw

 no vad

!

dial-peer voice 3002 voatm

 destination-pattern 3002

 called-number 4002

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 32

 codec aal2-profile custom 100 g726r32

 no vad

!

dial-peer voice 3003 voatm

 destination-pattern 3003

 called-number 4003

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 33

 codec aal2-profile ITUT 7 g729abr8

 no vad

.

.

.

dial-peer voice 3024 voatm

 destination-pattern 3024

 called-number 3024

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 54

 codec aal2-profile ITUT 7 g729abr8

 no vad

!

dial-peer voice 1 pots

 destination-pattern 4001

 port 1/0:0

!

dial-peer voice 2 pots

 destination-pattern 4002

 port 1/0:1

.

.

.

dial-peer voice 24 pots

 destination-pattern 4024

 port 1/0:23

!

!

line con 0

 exec-timeout 0 0

 transport input none

line aux 0

line vty 0 4

 login

!

no scheduler allocate

end

Configuration in CO Mode Example

The following example shows a G.SHDSL configuration of VoATM over AAL2, operating in central office (CO) mode, on a Cisco 2600 series router. This router in CO mode can be linked to another router that is configured to operate in CPE mode.

Router#

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname host2

!

memory-size iomem 10

voice-card 1

!

ip subnet-zero

ip host host2 225.255.255.224

!

no mgcp timer receive-rtcp

call rsvp-sync

!

!

controller T1 1/0

 framing esf

 linecode b8zs

 ds0-group 0 timeslots 1 type e&m-wink-start

 ds0-group 1 timeslots 2 type e&m-wink-start

.

.

.

ds0-group 23 timeslots 24 type e&m-wink-start

!

controller T1 1/1

 framing esf

 linecode b8zs

!

interface Ethernet0/0

 ip address 209.165.202.128 255.255.255.224

 half-duplex

 no cdp enable

!

interface Serial0/0

 no ip address

 shutdown

!

interface ATM0/1

 ip address 209.165.201.1 255.255.255.224

 dsl operating-mode gshdsl symmetric annex A

 dsl equipment-type co

 dsl linerate auto

 load-interval 30

 atm vc-per-vp 256

 no atm ilmi-keepalive

 pvc 10/100 

  vbr-rt 672 672 512

  encapsulation aal2

 !

 pvc 10/200 

  protocol ip 209.165.202.159 broadcast

  encapsulation aal5snap

 !

 no fair-queue

!

interface Ethernet0/1

 no ip address

 shutdown

!

ip classless

ip route 209.165.202.128 255.255.255.224 Ethernet0/0

no ip http server

!

!

snmp-server engineID local 000000090200003080477F20

snmp-server manager

!

voice-port 1/0:0

 local-alerting

 timeouts wait-release 3

 connection trunk 3001 

!

voice-port 1/0:1

 local-alerting

 timeouts wait-release 3

 connection trunk 3002 

.

.

.

voice-port 1/0:23

 local-alerting

 timeouts wait-release 3

 connection trunk 3024 

 shutdown

!

dial-peer cor custom

!

dial-peer voice 3001 voatm

 destination-pattern 3001

 called-number 4001

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 31

 codec aal2-profile ITUT 1 g711ulaw

 no vad

!

dial-peer voice 3002 voatm

 destination-pattern 3002

 called-number 4002

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 32

 codec aal2-profile custom 100 g726r32

 no vad

!

dial-peer voice 3003 voatm

 destination-pattern 3003

 called-number 4003

 session protocol aal2-trunk

 session target ATM0/1 pvc 10/100 33

 codec aal2-profile ITUT 7 g729abr8

 no vad

.

.

.

dial-peer voice 3024 voatm

 destination-pattern 3024

 called-number 3024

 session protocol aal2-trunk

session target ATM0/1 pvc 10/100 54

 codec aal2-profile ITUT 7 g729abr8

 no vad

!

dial-peer voice 1 pots

 destination-pattern 4001

 port 1/0:0

!

dial-peer voice 2 pots

 destination-pattern 4002

 port 1/0:1

.

.

.

dial-peer voice 24 pots

 destination-pattern 4024

 port 1/0:23

!

!

line con 0

 exec-timeout 0 0

 transport input none

line aux 0

line vty 0 4

 login

!

no scheduler allocate

end