Table Of Contents
Device Manager System Requirements
Finding the Software Version and Feature Set
Upgrading a Switch by Using the Device Manager
Upgrading a Switch by Using the CLI
Recovering from a Software Failure
Resolved Caveats in Cisco IOS Release 12.2(25)SE3
Resolved Caveats in Cisco IOS Release 12.2(25)SE2
Cisco Product Security Overview
Reporting Security Problems in Cisco Products
Product Alerts and Field Notices
Obtaining Technical Assistance
Cisco Technical Support & Documentation Website
Definitions of Service Request Severity
Obtaining Additional Publications and Information
Release Notes for the Cisco Catalyst Blade Switch 3040 for FSC, Cisco IOS Release 12.2(25)SEF2 and Later
Revised June 10, 2008
Cisco IOS Release 12.2(25)SEF2 and later run on the Cisco Catalyst Blade Switch 3040 for FSC, referred to as the switch. The switch is installed in the Fujitsu Siemens Computers (FSC) PRIMERGY BX600 system, referred to as the BX600 system.
Note
Before you install the switch in the BX600 system, upgrade the BX600 system management software to version 1.67 or later for the switch to operate properly.
Caution
Do not click enable in the Switch Blade Period Polling field, and do not enter a password in the Set Password for Polling Account field on the Blade Info window. Do not use the console menus to set polling or to set a password for a polling account.
Do not configure the switch management VLAN settings by using these fields on the Blade Info window: VLAN IP Address, Subnet Mask, or Gateway Address. Do not use the console menus to specify the management VLAN settings.
Do not use the Backup/Restore field on the Switch Blade window to back up and restore the switch configuration file, and always set Auto Restore to disable. Do not use the console menus to set
Backup/restore Control for the switch configuration file and always set Auto Restore Enable to disable.
Always use the Cisco IOS command-line interface (CLI) for these settings by logging onto the switch. See the switch command reference and software configuration guide on Cisco.com for more information.
Check for updates to this document at this URL for information about compatibility with the BX600 system software:
http://www.cisco.com/en/US/products/ps8743/prod_release_notes_list.html
These release notes include important information about Cisco IOS Release 12.2(25)SEF2 and any limitations, restrictions, and caveats that apply to them. Verify that these release notes are correct for your switch:
•
•
•
For the complete list of Cisco Catalyst Blade Switch 3040 for FSC documentation, see the "Related Documentation" section.
You can download the switch software from this site (registered Cisco.com users with a login password):
http://www.cisco.com/public/sw-center/sw-lan.shtml
This software release is part of a special release of Cisco IOS software that is not released on the same 8-week maintenance cycle that is used for other platforms. As maintenance releases and future software releases become available, they will be posted to Cisco.com in the Cisco IOS software area.
Cisco IOS Release 12.2(25)SEF2 is based on Cisco IOS Release 12.2(25)S. Open caveats in Cisco IOS Release 12.2(25)S also affect Cisco IOS Release 12.2(25)SEF2, unless they are listed in the Cisco IOS Release 12.2(25)SEF2 resolved caveats list. The list of open caveats in Cisco IOS Release 12.2(25)S is available at this URL:
/en/US/docs/ios/12_2s/release/notes/122Srn.html#wp2367913
Contents
This information is in the release notes:
•
•
•
•
•
•
•
•
•
System Requirements
The system requirements are described in these sections:
•
Hardware Supported
The hardware supported on this release is the Cisco Catalyst Blade Switch 3040 for FSC.
Device Manager System Requirements
These sections describes the hardware and software requirements for using the device manager:
•
•
Hardware Requirements
Table 1 lists the minimum hardware requirements for running the device manager.
Table 1 Minimum Hardware Requirements
Intel Pentium II1
64 MB2
256
1024 x 768
Small
1 We recommend Intel Pentium 4.
2 We recommend 256-MB DRAM.
Software Requirements
Table 2 lists the supported operating systems and browsers for using the device manager, which does not require a plug-in. The device manager verifies the browser version when starting a session to ensure that the browser is supported.
Note
Table 2 Supported Operating Systems and Browsers
Windows 2000
None
5.5 or 6.0
7.1
Windows XP
None
5.5 or 6.0
7.1
1 Service Pack 1 or higher is required for Internet Explorer 5.5.
Upgrading the Switch Software
These are the procedures for downloading software. Before downloading software, read this section for important information:
•
•
•
•
•
Finding the Software Version and Feature Set
The Cisco IOS image is stored as a bin file in a directory that is named with the Cisco IOS release. A subdirectory contains the files needed for web management. The image is stored on the system board flash device (flash:).
You can use the show version privileged EXEC command to see the software version that is running on your switch. The second line of the display shows the version.
You can also use the dir filesystem: privileged EXEC command to see the directory names of other software images that you might have stored in flash memory.
Deciding Which Files to Use
The upgrade procedures in these release notes describe how to perform the upgrade by using a combined tar file. This file contains the Cisco IOS image file and the files needed for the embedded device manager. You must use the combined tar file to upgrade the switch through the device manager. To upgrade the switch through the CLI, use the tar file and the archive download-sw privileged EXEC command.
Table 3 lists the filenames for this software release.
Archiving Software Images
Before upgrading your switch software, make sure that you have archived copies of the current Cisco IOS release and the Cisco IOS release to which you are upgrading. You should keep these archived images until you have upgraded all devices in the network to the new Cisco IOS image and until you have verified that the new Cisco IOS image works properly in your network.
Cisco routinely removes old Cisco IOS versions from Cisco.com. See Product Bulletin 2863 for more information:
http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/prod_bulletin0900aecd80281c0e.html
You can copy the bin software image file on the flash memory to the appropriate TFTP directory on a host by using the copy flash: tftp: privileged EXEC command.
Note
You can also configure the switch as a TFTP server to copy files from one switch to another without using an external TFTP server by using the tftp-server global configuration command. For more information about the tftp-server command, see the "Basic File Transfer Services Commands" section of the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2 at this URL:
/en/US/docs/ios/12_2/configfun/command/reference/frf011.html#wp1018426
Upgrading a Switch by Using the Device Manager
You can upgrade switch software by using the device manager. For detailed instructions, click Help.
Note
Upgrading a Switch by Using the CLI
This procedure is for copying the combined tar file to the switch. You copy the file to the switch from a TFTP server and extract the files. You can download an image file and replace or keep the current image.
To download software, follow these steps:
Step 1
Step 2
http://www.cisco.com/public/sw-center/sw-lan.shtml
Step 3
For more information, see Appendix B in the software configuration guide for this release.
Step 4
Step 5
Switch# ping tftp-server-addressFor more information about assigning an IP address and default gateway to the switch, see the software configuration guide for this release.
Step 6
Switch# archive download-sw /overwrite /reload tftp:[[//location]/directory]/image-name.tarThe /overwrite option overwrites the software image in flash memory with the downloaded one.
The /reload option reloads the system after downloading the image unless the configuration has been changed and not saved.
For //location, specify the IP address of the TFTP server.
For /directory/image-name.tar, specify the directory (optional) and the image to download. Directory and image names are case sensitive.
This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite the image on the switch:
Switch# archive download-sw /overwrite tftp://198.30.20.19/c3750-ipservices-tar.122-25.SED.tarYou can also download the image file from the TFTP server to the switch and keep the current image by replacing the /overwrite option with the /leave-old-sw option.
Recovering from a Software Failure
For additional recovery procedures, see the "Troubleshooting" chapter in the software configuration guide for this release.
Installation Notes
You can assign IP information to your switch by using these methods:
•
•
•
•
Limitations and Restrictions
You should review this section before you begin working with the switch. These are known limitations that will not be fixed, and there is not always a workaround. Some features might not work as documented, and some features could be affected by recent changes to the switch hardware or software.
This section contains these limitations:
•
•
Cisco IOS Limitations
These limitations apply to the switch:
•
•
Configuration
These are the configuration limitations:
•
This problem occurs under these conditions:
–
–
–
The workaround is to reconfigure the static IP address. (CSCea71176 and CSCdz11708)
•
The workaround is to configure the port for 10 Mbps and half duplex or to connect a hub or a nonaffected device to the switch. (CSCed39091)
•
The workaround is to enter the no switchport block unicast interface configuration command on that specific interface. (CSCee93822)
•
There is no workaround. This is a cosmetic error and does not affect the functionality of the switch. (CSCef59331)
Ethernet
This is the Ethernet limitation:
•
If this happens, traffic distribution is uneven on EtherChannel ports.
Changing the load balance distribution method or changing the number of ports in the EtherChannel can resolve this problem. Use any of these workarounds to improve EtherChannel load balancing:
–
–
–
–
For example, with load balance configured as dst-ip with 150 distinct incrementing destination IP addresses, and the number of ports in the EtherChannel set to either 2, 4, or 8, load distribution is optimal. (CSCeh81991)
IP
This is the IP limitation:
When the rate of received DHCP requests exceeds 2,000 packets per minute for a long time, the response time might be slow when you are using the console. The workaround is to use rate limiting on DHCP traffic to prevent a denial of service attack from occurring. (CSCeb59166)
IP Telephony
This is the IP telephony limitation:
After you change the access VLAN on a port that has IEEE 802.1x enabled, the IP phone address is removed. Because learning is restricted on IEEE 802.1x-capable ports, it takes approximately 30 seconds before the address is relearned. No workaround is necessary. This limitation is unlikely to affect the Cisco Catalyst Blade Switch 3040 for FSC because IP phones are not usually connected to the switch uplink ports. (CSCea85312)
MAC Addressing Multicasting
These are the multicasting limitations:
•
•
•
–
–
There is no workaround. (CSCec20128)
•
The switchport block multicast interface configuration command is only applicable to non-IP multicast traffic.
There is no workaround. (CSCee16865)
•
–
–
The workaround is to enter the clear ip mroute privileged EXEC command on the interface. (CSCef42436)
After you configure a switch to join a multicast group by entering the ip igmp join-group group-address interface configuration command, the switch does not receive join packets from the client, and the switch port connected to the client is removed from the IGMP snooping forwarding table.
Use one of these workarounds:
–
–
QoS
These are the quality of service (QoS) limitations:
•
•
SPAN and RSPAN
These are the SPAN and Remote SPAN (RSPAN) limitations.
•
•
•
Trunking
These are the trunking limitations:
•
•
•
VLAN
This is the VLAN limitation:
•
The workaround is to reduce the number of VLANs or trunks. (CSCeb31087)
Device Manager Limitations
These are the device manager limitations for this release:
•
The workaround is to click Yes when you are prompted to accept the certificate. (CSCef45718)
Important Notes
These sections describe the important notes related to this software release:
•
Cisco IOS Notes
These notes apply to Cisco IOS software:
•
•
•
00:02:57: %RADIUS-4-RADIUS_DEAD: RADIUS server 172.20.246.206:1645,1646 is not responding.If this message appears, make sure that there is network connectivity between the switch and the ACS. You should also make sure that the switch has been properly configured as an AAA client on the ACS.
Device Manager Notes
These notes apply to the device manager:
•
From Microsoft Internet Explorer:
1.
2.
3.
4.
5.
•
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
•
If you change the HTTP port, you must include the new port number when you enter the IP address in the browser Location or Address field (for example, http://10.1.126.45:184 where 184 is the new HTTP port number). You should write down the port number through which you are connected. Use care when changing the switch IP information.
If you are not using the default method of authentication (the enable password), you need to configure the HTTP server interface with the method of authentication used on the switch.
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
•
Open Caveats
This section describes the open severity 3 caveats for this software release.
Open Cisco IOS Caveats
This section describes the open severity 3 Cisco IOS configuration caveats with possible unexpected activity in this software release:
•
When an IEEE 802.1x restricted VLAN is configured on a port, and a hub with multiple devices is connected to that port, no syslog messages are generated.
This is not a supported configuration. Only one host should be connected to an IEEE 802.1x restricted VLAN port.
•
When the Control Plane Policing (CoPP) policy is configured to drop packets with IP options, packets with incorrectly created IP options are ignored.
The workaround is to configure CoPP to filter IP packets by source or destination address and not use the IP option for ACL filtering with CoPP.
•
There is an extra index in the port table of the ciscoStpExtensions MIB that does not exist in the portCrossIndex MIB. For example, extra indexes like 1000-16/40 are seen in stpxRootGuardConfigEnabled displays that do not exist in portCrossIndex, and they appear during an SNMP walk operation.
There is no workaround.
•
When a Cisco device configured for Network Admission Control and the EAP over UDP port number is changed from its default value and then changed back with the eou default switch configuration command, the port change does not take effect, and EAP over UDP sessions can remain in a hold state.
The workaround is to reset the EAP over UDP port number to its default value (0x5566) by using the eou port 21862 switch configuration command.
•
When you configure a Cisco IP Phone to use Network Admission Control, the CDP packet is delayed, and the phone is identified as an agentless host without an identity profile.
The workaround is to enter the eou initialize ip address switch configuration command to revalidate the host that CDP has learned.
•
MAC address notification traps do not work when port security is enabled on the interface.
The workaround is to disable port security on the interface.
•
When a source port for a SPAN session has IEEE 802.1x enabled, Extensible Authentication Protocol over LAN (EAPOL) packets are not visible to the packet sniffing tool.
The workaround is to enable a voice VLAN on the SPAN source port.
•
When you filter a MAC address by entering the mac-address-table static vlan drop global configuration command, IEEE 802.1X still authenticates that address.
There is no workaround.
•
The switch might fail or display illegal memory access messages during the SNMP timer process, when using the CiscoConfigCopyMIB to copy a configuration to the running configuration file.
This might happen when rmon alarm global configuration commands are present in the running configuration before downloading the copy.
The workaround is to disable all rmon alarm global configuration commands by using the no rmon alarm global configuration command before copying the configuration.
•
Removing the bridge topology change trap with the no snmp-server enable traps bridge topology change configuration command also disables the stpx root-inconsistency trap.
The workaround is to re-enable the stpx root-inconsistency trap by using the snmp-server enable traps stpx configuration command.
•
This error message appears during authentication when a method list is used and one of the methods in the method list is removed:
AAA-3-BADMETHODERROR:Cannot process authentication method 218959117There is no workaround. However, this is only an informational message and does not affect switch functionality.
•
A QoS service policy with a policy map containing more than 62 policers cannot be added to an interface by using the service-policy interface configuration command.
The workaround is to use policy maps with 62 or fewer policers.
•
The switch might display tracebacks similar to these examples when a large number of IEEE 802.1x supplicants try to repeatedly log in and log out.
Examples:
Jan 3 17:54:32 L3A3 307: Jan 3 18:04:13.459: %SM-4-BADEVENT: Event 'eapReq' is invalid for the current state 'auth_bend_idle': dot1x_auth_bend Fa9
Jan 3 17:54:32 L3A3 308: -Traceback= B37A84 18DAB0 2FF6C0 2FF260 8F2B64 8E912C Jan 3 19:06:13 L3A3 309: Jan 3 19:15:54.720: %SM-4-BADEVENT: Event 'eapReq_no_reAuthMax' is invalid for the current ate 'auth_restart': dot1x_auth Fa4
Jan 3 19:06:13 L3A3 310: -Traceback= B37A84 18DAB0 3046F4 302C80 303228 8F2B64 8E912C Jan 3 20:41:44 L3A3 315: .Jan 3 20:51:26.249: %SM-4-BADEVENT: Event 'eapSuccess' is invalid for the current state 'auth_restart': dot1x_auth Fa9
Jan 3 20:41:44 L3A3 316: -Traceback= B37A84 18DAB0 304648 302C80 303228 8F2B64 8E912C
There is no workaround.
•
When IEEE 802.1x is globally disabled on the switch by using the no dot1x system-auth-control global configuration command, some interface level configuration commands, including the dot1x timeout and dot1x mac-auth-bypass commands, become unavailable.
The workaround is to enable the dot1x system-auth-control global configuration command before attempting to configure interface level IEEE 802.1x parameters.
•
When you remove a voice VLAN from a secure port, this message appears:
PORT_SECURITY-6-VLAN_REMOVED: VLAN xxx is no longer allowed on port ppp. Its port security configuration has been removed.
There is no workaround.This is only a notification; no action is required.
Resolved Caveats
These sections describe the resolved caveats in these releases:
Resolved Caveats in Cisco IOS Release 12.2(25)SE3
Resolved Caveats in Cisco IOS Release 12.2(25)SE2
Resolved Caveats in Cisco IOS Release 12.2(25)SE3
This caveat was resolved in release Cisco IOS Release 12.2(25)SEF3:
CSCsg70355
Date changes in Daylight Savings Time in 2007 might no longer cause Cisco IOS to generate timestamps, such as in syslog messages, that are inaccurate by 1 hour.
Resolved Caveats in Cisco IOS Release 12.2(25)SE2
This caveat was resolved in release Cisco IOS Release 12.2(25)SEF2:
•
Multiple Cisco products contain either of two authentication vulnerabilities in the Simple Network Management Protocol version 3 (SNMPv3) feature. These vulnerabilities can be exploited when processing a malformed SNMPv3 message. These vulnerabilities could allow the disclosure of network information or may enable an attacker to perform configuration changes to vulnerable devices. The SNMP server is an optional service that is disabled by default. Only SNMPv3 is impacted by these vulnerabilities. Workarounds are available for mitigating the impact of the vulnerabilities described in this document.
The United States Computer Emergency Response Team (US-CERT) has assigned Vulnerability Note VU#878044 to these vulnerabilities.
Common Vulnerabilities and Exposures (CVE) identifier CVE-2008-0960 has been assigned to these vulnerabilities.
This advisory will be posted at http://www.cisco.com/warp/public/707/cisco-sa-20080610-snmpv3.shtml
Related Documentation
These documents provide complete information about the Cisco Catalyst Blade Switch 3040 for FSC and are available at Cisco.com:
http://www.cisco.com/en/US/products/ps8743/tsd_products_support_series_home.html
You can order printed copies of documents with a DOC-xxxxxx= number from the Cisco.com sites and from the telephone numbers listed in the "Obtaining Documentation" section.
These documents provide complete information about the Cisco Catalyst Blade Switch 3040 for FSC:
•
•
•
•
•
•
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. This section explains the product documentation resources that Cisco offers.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/techsupport
You can access the Cisco website at this URL:
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Product Documentation DVD
The Product Documentation DVD is a library of technical product documentation on a portable medium. The DVD enables you to access installation, configuration, and command guides for Cisco hardware and software products. With the DVD, you have access to the HTML documentation and some of the PDF files found on the Cisco website at this URL:
http://www.cisco.com/univercd/home/home.htm
The Product Documentation DVD is created and released regularly. DVDs are available singly or by subscription. Registered Cisco.com users can order a Product Documentation DVD (product number DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at the Product Documentation Store at this URL:
http://www.cisco.com/go/marketplace/docstore
Ordering Documentation
You must be a registered Cisco.com user to access Cisco Marketplace. Registered users may order Cisco documentation at the Product Documentation Store at this URL:
http://www.cisco.com/go/marketplace/docstore
If you do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Documentation Feedback
You can provide feedback about Cisco technical documentation on the Cisco Technical Support & Documentation site area by entering your comments in the feedback form available in every online document.
Cisco Product Security Overview
Cisco provides a free online Security Vulnerability Policy portal at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you will find information about how to do the following:
•
•
•
A current list of security advisories, security notices, and security responses for Cisco products is available at this URL:
To see security advisories, security notices, and security responses as they are updated in real time, you can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT:
•
An emergency is either a condition in which a system is under active attack or a condition for which a severe and urgent security vulnerability should be reported. All other conditions are considered nonemergencies.
•
In an emergency, you can also reach PSIRT by telephone:
•
•
Tip
Never use a revoked encryption key or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
The link on this page has the current PGP key ID in use.
If you do not have or use PGP, contact PSIRT to find other means of encrypting the data before sending any sensitive material.
Product Alerts and Field Notices
Modifications to or updates about Cisco products are announced in Cisco Product Alerts and Cisco Field Notices. You can receive Cisco Product Alerts and Cisco Field Notices by using the Product Alert Tool on Cisco.com. This tool enables you to create a profile and choose those products for which you want to receive information.
To access the Product Alert Tool, you must be a registered Cisco.com user. (To register as a Cisco.com user, go to this URL: http://tools.cisco.com/RPF/register/register.do) Registered users can access the tool at this URL: http://tools.cisco.com/Support/PAT/do/ViewMyProfiles.do?local=en
Obtaining Technical Assistance
Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.com features extensive online support resources. In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not have a valid Cisco service contract, contact your reseller.
Cisco Technical Support & Documentation Website
The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Note
Tip
If you suspect that the browser is not refreshing a web page, force the browser to update the web page by holding down the Ctrl key while pressing F5.
To find technical information, narrow your search to look in technical documentation, not the entire Cisco.com website. On the Cisco.com home page, click the Advanced Search link under the Search box and then click the Technical Support & Documentation radio button.
To provide feedback about the Cisco.com website or a particular technical document, click Contacts & Feedback at the top of any Cisco.com web page.
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411
Australia: 1 800 805 227
EMEA: +32 2 704 55 55
USA: 1 800 553 2447For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.
Severity 1 (S1)—An existing network is "down" or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of the network is impaired while most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online and printed sources.
•
http://www.cisco.com/offer/subscribe
•
•
http://www.cisco.com/go/marketplace/
•
•
•
http://www.cisco.com/en/US/products/index.html
•
http://www.cisco.com/discuss/networking
•
http://www.cisco.com/univercd/cc/td/doc/abtunicd/136957.htm
•
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2006-2008 Cisco Systems, Inc. All rights reserved.
Guest
