Configuring NTP
This chapter describes how to configure the Network Time Protocol (NTP) and includes the following topics:
•
Information about NTP
•
Prerequisites for NTP
•
Configuration Guidelines and Limitations
•
Default Settings
•
Configuring an NTP Server and Peer
•
Verifying the NTP Configuration
•
NTP Example Configuration
•
Additional References
•
Feature History for NTP
Information about NTP
The Network Time Protocol (NTP) synchronizes timekeeping among a set of distributed time servers and clients. This synchronization allows you to correlate events when you receive system logs and other time-specific events from multiple network devices.
NTP uses the User Datagram Protocol (UDP) as its transport protocol. All NTP communication uses the Universal Time Coordinated (UTC) standard. An NTP server usually receives its time from an authoritative time source, such as a radio clock or an atomic clock attached to a time server. NTP distributes this time across the network. NTP is extremely efficient; no more than one packet per minute is necessary to synchronize two machines to within a millisecond of each other.
NTP uses a stratum to describe how many NTP hops away that a network device is from an authoritative time source. A stratum 1 time server has an authoritative time source (such as an atomic clock) directly attached to the server. A stratum 2 NTP server receives its time through NTP from a stratum 1 NTP server, which in turn connects to the authoritative time source.
NTP avoids synchronizing to a network device that may keep accurate time. NTP never synchronizes to a system that is not in turn synchronized itself. NTP compares the time reported by several network devices and does not synchronize to a network device that has a time that is significantly different than the others, even if its stratum is lower.
Cisco NX-OS cannot act as a stratum 1 server. You cannot connect to a radio or atomic clock. We recommend that the time service that you use for your network is derived from the public NTP servers available on the Internet.
If the network is isolated from the Internet, Cisco NX-OS allows you to configure a network device so that the device acts as though it is synchronized through NTP, when in fact it has determined the time using other means. Other network devices can then synchronize to that network device through NTP.
NTP Peers
NTP allows you to create a peer relationship between two networking devices. A peer can provide time on its own or connect to an NTP server. If both the local device and the remote peer point to different NTP servers, your NTP service is more reliable. The local device maintains the right time even if its NTP server fails by using the time from the peer.
Figure 8-1 displays a network with two NTP stratum 2 servers and two switches.
Figure 8-1 NTP Peer and Server Association
In this configuration, switch 1 and switch 2 are NTP peers. switch 1 uses stratum-2 server 1, while switch 2 uses stratum-2 server 2. If stratum-2 server-1 fails, switch 1 maintains the correct time through its peer association with switch 2.
High Availability
Stateless restarts are supported for NTP. After a reboot or a supervisor switchover, the running configuration is applied.
You can configure NTP peers to provide redundancy in case an NTP server fails.
Prerequisites for NTP
If you configure NTP, you must have connectivity to at least one server that is running NTP.
Configuration Guidelines and Limitations
NTP has the following configuration guidelines and limitations:
•
You should have a peer association with another device only when you are sure that your clock is reliable (which means that you are a client of a reliable NTP server).
•
A peer configured alone takes on the role of a server and should be used as backup. If you have two servers, you can configure several devices to point to one server and the remaining devices point to the other server. You can then configure peer association between these two servers to create a more reliable NTP configuration.
•
If you only have one server, you should configure all the devices as clients to that server.
•
You can configure up to 64 NTP entities (servers and peers).
Default Settings
The following table lists the default settings for CDP and NTP parameters.
Configuring an NTP Server and Peer
Use this procedure to configure an NTP server and peer.
BEFORE YOU BEGIN
•
You can configure NTP using IPv4 addresses or domain name server (DNS) names.
SUMMARY STEPS
1.
config t
2.
ntp server {ip-address | dns-name}
3.
ntp peer {ip-address | dns-name}
4.
show ntp peers
5.
copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
config t Example: n1000v# config t n1000v(config)# |
Places you into the CLI Global Configuration mode. |
Step 2 |
ntp server {ip-address | dns-name} Example: n1000v(config)# ntp server 192.0.2.10 |
Forms an association with a server. |
Step 3 |
ntp peer {ip-address | dns-name} n1000v(config)# ntp peer 2001:0db8::4101 |
Forms an association with a peer. You can specify multiple peer associations. |
Step 4 |
show ntp peers Example: n1000v(config)# show ntp peers |
(Optional) Displays the configured server and peers. Note A domain name is resolved only when you have a DNS server configured. |
Step 5 |
copy running-config startup-config Example: n1000v(config-if)# copy running-config startup-config |
(Optional) Saves the running configuration persistently through reboots and restarts by copying it to the startup configuration. |
The following is an example configures an NTP server and peer:
n1000v# config t
n1000v(config)# ntp server 192.0.2.10
n1000v(config# ntp peer 2001:0db8::4101
Clearing NTP Statistics or Sessions
Use the following commands to clear NTP statistics or sessions.
|
|
clear ntp statistics |
Clears the NTP statistics. |
clear ntp session |
Clears the NTP sessions. |
Verifying the NTP Configuration
To display NTP configuration information, use one of the following commands:
|
|
show ntp peer-status |
Displays the status for all NTP servers and peers. |
show ntp peers |
Displays all the NTP peers. |
show ntp statistics {io | local | memory | peer {ip-address | dns-name} |
Displays the NTP statistics |
NTP Example Configuration
This example configures an NTP server:
config t
ntp server 192.0.2.10
Additional References
For additional information related to NTP, see the following sections:
•
Related Documents
•
Standards
Related Documents
|
|
Interface |
Cisco Nexus 1000V Interface Configuration Guide, Release 4.2(1)SV1(4) |
Complete command syntax, command modes, command history, defaults, usage guidelines, and examples |
Cisco Nexus 1000V Command Reference, Release 4.2(1)SV1(4) |
Standards
|
|
No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature. |
— |
Feature History for NTP
This section shows the NTP feature release history.
|
|
|
NTP |
4.0(4)SV1(1) |
This feature was introduced. |