- Preface
- New and Changed Information
- Layer 3 Interfaces Commands
- H Commands
- I Commands
- N Commands
- IGMP Commands
- C Commands
- I Commands
- Show Commands
- IGMP Snooping Commands
- C Commands
- H Commands
- I Commands
- Show Commands
- MSDP Commands
- C Commands
- F Commands
- I Commands
- R Commands
- Show Commands
- PIM Commands
- C Commands
- F Commands
- I Commands
- R Commands
- Show Commands
C Commands
This chapter describes the Cisco NX-OS PIM commands that begin with C.
clear ip mroute
To clear the multicast routing table, use the clear ip mroute command.
clear ip mroute { * | group [ source ] | group-prefix } [ vrf { vrf-name | all | default | management }]
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
The clear routing multicast command is an alternative form of this command.
The clear ip mroute command is used for debugging purposes. However, this command is not supported for group-prefix option, i.e., subnet routes.
Examples
This example shows how to clear the multicast routing table:
switch(
config)#
clear ip mroute *
switch(
config)#
Related Commands
|
|
---|---|
clear ip pim event-history
To clear information in the IPv4 Protocol Independent Multicast (PIM) event history buffers, use the clear ip pim event-history command.
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
Examples
This example shows how to clear information in the PIM event history buffers:
switch(config)#
clear ip pim event-history
Related Commands
|
|
---|---|
clear ip pim interface statistics
To clear Protocol Independent Multicast (PIM) counters for a specified interface, use the clear ip pim interface statistics command.
clear ip pim interface statistics [ ethernet slot / port | port-channel channel-number [. sub_if-number ] | vlan vlan-id ]
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
Examples
This example shows how to clear the PIM counters for a specified interface:
switch#
clear ip pim interface statistics ethernet 2/1
switch#
Related Commands
|
|
---|---|
clear ip pim policy statistics
To clear Protocol Independent Multicast (PIM) policy counters, use the clear ip pim policy statistics command.
clear ip pim policy statistics { jp-policy | neighbor-policy } { ethernet slot / port | port-channel channel-number [. sub_if-number ] | vlan vlan-id }
clear ip pim policy statistics register-policy [ vrf { vrf-name | all | default | management }]
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
Examples
This example shows how to clear PIM register policy counters:
switch#
clear ip pim policy statistics register-policy
switch#
Related Commands
|
|
---|---|
clear ip pim route
To clear routes specific to Protocol Independent Multicast (PIM) for IPv4, use the clear ip pim route command.
clear ip pim route { * | group [ source ] | group-prefix } [ vrf { vrf-name | all | default | management }]
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
Examples
This example shows how to clear the all the routes specific to PIM:
switch(
config)#
clear ip pim route *
switch(
config)#
Related Commands
|
|
---|---|
clear ip pim statistics
To clear Protocol Independent Multicast (PIM) statistics counters, use the clear ip pim statistics command.
clear ip pim statistics [ vrf { vrf-name | all | default | management }]
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
Examples
This example shows how to clear PIM statistics counters:
switch#
clear ip pim statistics
switch#
Related Commands
|
|
---|---|
clear ip routing multicast event-history
To clear information in the IPv4 Multicast Routing Information Base (MRIB) event history buffers, use the clear ip routing multicast event-history command.
clear ip routing multicast event-history { cli | mfdm-debugs | mfdm-events | mfdm-stats | rib | vrf }
Syntax Description
Clears the multicast FIB distribution (MFDM) debug history buffer. |
|
Clears the virtual routing and forwarding (VRF) event history buffer. |
Command Default
Command Modes
Command History
|
|
Usage Guidelines
Examples
This example shows how to clear information in the MRIB RIB event history buffer:
Related Commands
|
|
---|---|
Displays information in the IPv4 MRIB event history buffers. |
clear routing multicast
To clear the IPv4 multicast routing table, use the clear routing multicast command.
clear routing [ ip | ipv4 ] multicast { * | group [ source ] | group-prefix } [ vrf { vrf-name | all | default | management }]
Syntax Description
Command Default
Command Modes
Command History
|
|
Usage Guidelines
The clear ip mroute command is an alternative form of this command.
Examples
This example shows how to clear the IPv4 multicast routing table:
switch(
config)#
clear routing multicast *
switch(
config)#
Related Commands
|
|
---|---|