Configuring DHCP Features and IP Source Guard Features

This chapter describes how to configure DHCP snooping and option-82 data insertion, and the DHCP server port-based address allocation features on the Catalyst 3750 switch. It also describes how to configure the IP source guard feature. Unless otherwise noted, the term switch refers to a standalone switch and to a switch stack.

Note For complete syntax and usage information for the commands used in this chapter, see the command reference for this release, and see the "DHCP Commands" section in the Cisco IOS IP Command Reference, Volume 1 of 3: Addressing and Services, Release 12.2 from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Command References.

This chapter consists of these sections:

•Understanding DHCP Snooping

•Configuring DHCP Snooping

•Displaying DHCP Snooping Information

•Understanding IP Source Guard

•Configuring IP Source Guard

•Displaying IP Source Guard Information

•Understanding DHCP Server Port-Based Address Allocation

•Configuring DHCP Server Port-Based Address Allocation

•Displaying DHCP Server Port-Based Address Allocation

Understanding DHCP Snooping

DHCP is widely used in LAN environments to dynamically assign host IP addresses from a centralized server, which significantly reduces the overhead of administration of IP addresses. DHCP also helps conserve the limited IP address space because IP addresses no longer need to be permanently assigned to hosts; only those hosts that are connected to the network consume IP addresses.

These sections contain this information:

•DHCP Server

•DHCP Relay Agent

•DHCP Snooping

•Option-82 Data Insertion

•Cisco IOS DHCP Server Database

•DHCP Snooping Binding Database

•DHCP Snooping and Switch Stacks

For information about the DHCP client, see the "Configuring DHCP" section of the "IP Addressing and Services" section of the Cisco IOS IP Configuration Guide, Release 12.2 from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Configuration Guides.

DHCP Server

The DHCP server assigns IP addresses from specified address pools on a switch or router to DHCP clients and manages them. If the DHCP server cannot give the DHCP client the requested configuration parameters from its database, it forwards the request to one or more secondary DHCP servers defined by the network administrator.

DHCP Relay Agent

A DHCP relay agent is a Layer 3 device that forwards DHCP packets between clients and servers. Relay agents forward requests and replies between clients and servers when they are not on the same physical subnet. Relay agent forwarding is different from the normal Layer 2 forwarding, in which IP datagrams are switched transparently between networks. Relay agents receive DHCP messages and generate new DHCP messages to send on output interfaces.

DHCP Snooping

DHCP snooping is a DHCP security feature that provides network security by filtering untrusted DHCP messages and by building and maintaining a DHCP snooping binding database, also referred to as a DHCP snooping binding table.

DHCP snooping acts like a firewall between untrusted hosts and DHCP servers. You use DHCP snooping to differentiate between untrusted interfaces connected to the end user and trusted interfaces connected to the DHCP server or another switch.

Note For DHCP snooping to function properly, all DHCP servers must be connected to the switch through trusted interfaces.

An untrusted DHCP message is a message that is received from outside the network or firewall. When you use DHCP snooping in a service-provider environment, an untrusted message is sent from a device that is not in the service-provider network, such as a customer's switch. Messages from unknown devices are untrusted because they can be sources of traffic attacks.

The DHCP snooping binding database has the MAC address, the IP address, the lease time, the binding type, the VLAN number, and the interface information that corresponds to the local untrusted interfaces of a switch. It does not have information regarding hosts interconnected with a trusted interface.

In a service-provider network, a trusted interface is connected to a port on a device in the same network. An untrusted interface is connected to an untrusted interface in the network or to an interface on a device that is not in the network.

When a switch receives a packet on an untrusted interface and the interface belongs to a VLAN in which DHCP snooping is enabled, the switch compares the source MAC address and the DHCP client hardware address. If the addresses match (the default), the switch forwards the packet. If the addresses do not match, the switch drops the packet.

The switch drops a DHCP packet when one of these situations occurs:

•A packet from a DHCP server, such as a DHCPOFFER, DHCPACK, DHCPNAK, or DHCPLEASEQUERY packet, is received from outside the network or firewall.

•A packet is received on an untrusted interface, and the source MAC address and the DHCP client hardware address do not match.

•The switch receives a DHCPRELEASE or DHCPDECLINE broadcast message that has a MAC address in the DHCP snooping binding database, but the interface information in the binding database does not match the interface on which the message was received.

•A DHCP relay agent forwards a DHCP packet that includes a relay-agent IP address that is not 0.0.0.0, or the relay agent forwards a packet that includes option-82 information to an untrusted port.

If the switch is an aggregation switch supporting DHCP snooping and is connected to an edge switch that is inserting DHCP option-82 information, the switch drops packets with option-82 information when packets are received on an untrusted interface. If DHCP snooping is enabled and packets are received on a trusted port, the aggregation switch does not learn the DHCP snooping bindings for connected devices and cannot build a complete DHCP snooping binding database.

When option-82 information is inserted by an edge switch in software releases earlier than Cisco IOS Release 12.2(25)SEA, you cannot configure DHCP snooping on an aggregation switch because the DHCP snooping bindings database is not properly populated. You also cannot configure IP source guard and dynamic Address Resolution Protocol (ARP) inspection on the switch unless you use static bindings or ARP access control lists (ACLs).

When an aggregation switch can be connected to an edge switch through an untrusted interface and you enter the ip dhcp snooping information option allow-untrusted global configuration command, the aggregation switch accepts packets with option-82 information from the edge switch. The aggregation switch learns the bindings for hosts connected through an untrusted switch interface. The DHCP security features, such as dynamic ARP inspection or IP source guard, can still be enabled on the aggregation switch while the switch receives packets with option-82 information on untrusted input interfaces to which hosts are connected. The port on the edge switch that connects to the aggregation switch must be configured as a trusted interface.

Option-82 Data Insertion

In residential, metropolitan Ethernet-access environments, DHCP can centrally manage the IP address assignments for a large number of subscribers. When the DHCP option-82 feature is enabled on the switch, a subscriber device is identified by the switch port through which it connects to the network (in addition to its MAC address). Multiple hosts on the subscriber LAN can be connected to the same port on the access switch and are uniquely identified.

Note The DHCP option-82 feature is supported only when DHCP snooping is globally enabled and on the VLANs to which subscriber devices using this feature are assigned.

Figure 23-1 is an example of a metropolitan Ethernet network in which a centralized DHCP server assigns IP addresses to subscribers connected to the switch at the access layer. Because the DHCP clients and their associated DHCP server do not reside on the same IP network or subnet, a DHCP relay agent (the Catalyst switch) is configured with a helper address to enable broadcast forwarding and to transfer DHCP messages between the clients and the server.

Figure 23-1 DHCP Relay Agent in a Metropolitan Ethernet Network

When you enable the DHCP snooping information option 82 on the switch, this sequence of events occurs:

•The host (DHCP client) generates a DHCP request and broadcasts it on the network.

•When the switch receives the DHCP request, it adds the option-82 information in the packet. By default, the remote-ID suboption is the switch MAC address, and the circuit-ID suboption is the port identifier, vlan-mod-port, from which the packet is received.

•If the IP address of the relay agent is configured, the switch adds this IP address in the DHCP packet.

•The switch forwards the DHCP request that includes the option-82 field to the DHCP server.

•The DHCP server receives the packet. If the server is option-82-capable, it can use the remote ID, the circuit ID, or both to assign IP addresses and implement policies, such as restricting the number of IP addresses that can be assigned to a single remote ID or circuit ID. Then the DHCP server echoes the option-82 field in the DHCP reply.

•The DHCP server unicasts the reply to the switch if the request was relayed to the server by the switch. The switch verifies that it originally inserted the option-82 data by inspecting the remote ID and possibly the circuit ID fields. The switch removes the option-82 field and forwards the packet to the switch port that connects to the DHCP client that sent the DHCP request.

In the default suboption configuration, when the described sequence of events occurs, the values in these fields in Figure 23-2 do not change:

•Circuit-ID suboption fields

–Suboption type

–Length of the suboption type

–Circuit-ID type

–Length of the circuit-ID type

•Remote-ID suboption fields

–Suboption type

–Length of the suboption type

–Remote-ID type

–Length of the remote-ID type

In the port field of the circuit-ID suboption, the port numbers start at 3. For example, on a switch with 24 10/100 ports and small form-factor pluggable (SFP) module slots, port 3 is the Fast Ethernet x/0/1 port, port 4 is the Fast Ethernet x/0/2 port, and so forth, where x is the stack member number. Port 27 is the SFP module slot x/0/1, and so forth.

Figure 23-2 shows the packet formats for the remote-ID suboption and the circuit-ID suboption when the default suboption configuration is used. For the circuit-ID suboption, the module number corresponds to the switch number in the stack. The switch uses the packet formats when you globally enable DHCP snooping and enter the ip dhcp snooping information option global configuration command.

Figure 23-2 Suboption Packet Formats

Figure 23-3 shows the packet formats for user-configured remote-ID and circuit-ID suboptions The switch uses these packet formats when DHCP snooping is globally enabled and when the ip dhcp snooping information option format remote-id global configuration command and the ip dhcp snooping vlan information option format-type circuit-id string interface configuration command are entered.

The values for these fields in the packets change from the default values when you configure the remote-ID and circuit-ID suboptions:

•Circuit-ID suboption fields

–The circuit-ID type is 1.

–The length values are variable, depending on the length of the string that you configure.

•Remote-ID suboption fields

–The remote-ID type is 1.

–The length values are variable, depending on the length of the string that you configure.

Figure 23-3 User-Configured Suboption Packet Formats

Cisco IOS DHCP Server Database

During the DHCP-based autoconfiguration process, the designated DHCP server uses the Cisco IOS DHCP server database. It has IP addresses, address bindings, and configuration parameters, such as the boot file.

An address binding is a mapping between an IP address and a MAC address of a host in the Cisco IOS DHCP server database. You can manually assign the client IP address, or the DHCP server can allocate an IP address from a DHCP address pool. For more information about manual and automatic address bindings, see the "Configuring DHCP" chapter of the Cisco IOS IP Configuration Guide,
Release 12.2 from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Configuration Guides.

DHCP Snooping Binding Database

When DHCP snooping is enabled, the switch uses the DHCP snooping binding database to store information about untrusted interfaces. The database can have up to 8192 bindings.

Each database entry (binding) has an IP address, an associated MAC address, the lease time (in hexadecimal format), the interface to which the binding applies, and the VLAN to which the interface belongs. The database agent stores the bindings in a file at a configured location. At the end of each entry is a checksum that accounts for all the bytes from the start of the file through all the bytes associated with the entry. Each entry is 72 bytes, followed by a space and then the checksum value.

To keep the bindings when the switch reloads, you must use the DHCP snooping database agent. If the agent is disabled, dynamic ARP inspection or IP source guard is enabled, and the DHCP snooping binding database has dynamic bindings, the switch loses its connectivity. If the agent is disabled and only DHCP snooping is enabled, the switch does not lose its connectivity, but DHCP snooping might not prevent DHCP spoofing attacks.

When reloading, the switch reads the binding file to build the DHCP snooping binding database. The switch updates the file when the database changes.

When a switch learns of new bindings or when it loses bindings, the switch immediately updates the entries in the database. The switch also updates the entries in the binding file. The frequency at which the file is updated is based on a configurable delay, and the updates are batched. If the file is not updated in a specified time (set by the write-delay and abort-timeout values), the update stops.

This is the format of the file with bindings: 

<initial-checksum> 

TYPE DHCP-SNOOPING 

VERSION 1 

BEGIN 

<entry-1> <checksum-1> 

<entry-2> <checksum-1-2> 

... 

... 

<entry-n> <checksum-1-2-..-n> 

END

Each entry in the file is tagged with a checksum value that the switch uses to verify the entries when it reads the file. The initial-checksum entry on the first line distinguishes entries associated with the latest file update from entries associated with a previous file update.

This is an example of a binding file: 

2bb4c2a1

TYPE DHCP-SNOOPING

VERSION 1

BEGIN

192.1.168.1 3 0003.47d8.c91f 2BB6488E interface-id 21ae5fbb

192.1.168.3 3 0003.44d6.c52f 2BB648EB interface-id 1bdb223f

192.1.168.2 3 0003.47d9.c8f1 2BB648AB interface-id 584a38f0

END

When the switch starts and the calculated checksum value equals the stored checksum value, the switch reads entries from the binding file and adds the bindings to its DHCP snooping binding database. The switch ignores an entry when one of these situations occurs:

•The switch reads the entry and the calculated checksum value does not equal the stored checksum value. The entry and the ones following it are ignored.

•An entry has an expired lease time (the switch might not remove a binding entry when the lease time expires).

•The interface in the entry no longer exists on the system.

•The interface is a routed interface or a DHCP snooping-trusted interface.

DHCP Snooping and Switch Stacks

DHCP snooping is managed on the stack master. When a new switch joins the stack, the switch receives the DHCP snooping configuration from the stack master. When a member leaves the stack, all DHCP snooping address bindings associated with the switch age out.

All snooping statistics are generated on the stack master. If a new stack master is elected, the statistics counters reset.

When a stack merge occurs, all DHCP snooping bindings in the stack master are lost if it is no longer the stack master. With a stack partition, the existing stack master is unchanged, and the bindings belonging to the partitioned switches age out. The new master of the partitioned stack begins processing the new incoming DHCP packets. For more information about switch stacks, see Chapter 5, "Managing Switch Stacks."

Configuring DHCP Snooping

These sections contain this configuration information:

•Default DHCP Snooping Configuration

•DHCP Snooping Configuration Guidelines

•Configuring the DHCP Relay Agent

•Specifying the Packet Forwarding Address

•Configuring the DHCP Relay Agent

•Specifying the Packet Forwarding Address

•Enabling DHCP Snooping and Option 82

•Enabling DHCP Snooping on Private VLANs

•Enabling the Cisco IOS DHCP Server Database

•Enabling the DHCP Snooping Binding Database Agent

Default DHCP Snooping Configuration

Table 23-1 shows the default DHCP snooping configuration.

Table 23-1 Default DHCP Snooping Configuration 

Feature
Default Setting

DHCP server

Enabled in Cisco IOS software, requires configuration1

DHCP relay agent

Enabled2

DHCP packet forwarding address

None configured

Checking the relay agent information

Enabled (invalid messages are dropped)2

DHCP relay agent forwarding policy

Replace the existing relay agent information2

DHCP snooping enabled globally

Disabled

DHCP snooping information option

Enabled

DHCP snooping option to accept packets on untrusted input interfaces3

Disabled

DHCP snooping limit rate

None configured

DHCP snooping trust

Untrusted

DHCP snooping VLAN

Disabled

DHCP snooping MAC address verification

Enabled

Cisco IOS DHCP server binding database

Enabled in Cisco IOS software, requires configuration.

Note The switch gets network addresses and configuration parameters only from a device configured as a DHCP server.

DHCP snooping binding database agent

Enabled in Cisco IOS software, requires configuration. This feature is operational only when a destination is configured.

1 The switch responds to DHCP requests only if it is configured as a DHCP server.

2 The switch relays DHCP packets only if the IP address of the DHCP server is configured on the SVI of the DHCP client.

3 Use this feature when the switch is an aggregation switch that receives packets with option-82 information from an edge switch.


DHCP Snooping Configuration Guidelines

These are the configuration guidelines for DHCP snooping.

•You must globally enable DHCP snooping on the switch.

•DHCP snooping is not active until DHCP snooping is enabled on a VLAN.

•Before globally enabling DHCP snooping on the switch, make sure that the devices acting as the DHCP server and the DHCP relay agent are configured and enabled.

•When you globally enable DHCP snooping on the switch, these Cisco IOS commands are not available until snooping is disabled. If you enter these commands, the switch returns an error message, and the configuration is not applied.

–ip dhcp relay information check global configuration command

–ip dhcp relay information policy global configuration command

–ip dhcp relay information trust-all global configuration command

–ip dhcp relay information trusted interface configuration command

•Before configuring the DHCP snooping information option on your switch, be sure to configure the device that is acting as the DHCP server. For example, you must specify the IP addresses that the DHCP server can assign or exclude, or you must configure DHCP options for these devices.

•When configuring a large number of circuit IDs on a switch, consider the impact of lengthy character strings on the NVRAM or the flash memory. If the circuit-ID configurations, combined with other data, exceed the capacity of the NVRAM or the flash memory, an error message appears.

•Before configuring the DHCP relay agent on your switch, make sure to configure the device that is acting as the DHCP server. For example, you must specify the IP addresses that the DHCP server can assign or exclude, configure DHCP options for devices, or set up the DHCP database agent.

•If the DHCP relay agent is enabled but DHCP snooping is disabled, the DHCP option-82 data insertion feature is not supported.

•If a switch port is connected to a DHCP server, configure a port as trusted by entering the ip dhcp snooping trust interface configuration command.

•If a switch port is connected to a DHCP client, configure a port as untrusted by entering the no ip dhcp snooping trust interface configuration command.

•Follow these guidelines when configuring the DHCP snooping binding database:

–Because both NVRAM and the flash memory have limited storage capacity, we recommend that you store the binding file on a TFTP server.

–For network-based URLs (such as TFTP and FTP), you must create an empty file at the configured URL before the switch can write bindings to the binding file at that URL. See the documentation for your TFTP server to determine whether you must first create an empty file on the server; some TFTP servers cannot be configured this way.

–To ensure that the lease time in the database is accurate, we recommend that you enable and configure NTP. For more information, see the "Configuring NTP" section on page 7-3.

–If NTP is configured, the switch writes binding changes to the binding file only when the switch system clock is synchronized with NTP.

•Do not enter the ip dhcp snooping information option allow-untrusted command on an aggregation switch to which an untrusted device is connected. If you enter this command, an untrusted device might spoof the option-82 information.

•You can display DHCP snooping statistics by entering the show ip dhcp snooping statistics user EXEC command, and you can clear the snooping statistics counters by entering the clear ip dhcp snooping statistics privileged EXEC command.

Note Do not enable Dynamic Host Configuration Protocol (DHCP) snooping on RSPAN VLANs. If DHCP snooping is enabled on RSPAN VLANs, DHCP packets might not reach the RSPAN destination port.

Configuring the DHCP Relay Agent

Beginning in privileged EXEC mode, follow these steps to enable the DHCP relay agent on the switch:

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

service dhcp

Enable the DHCP server and relay agent on your switch. By default, this feature is enabled.

Step 3 

end

Return to privileged EXEC mode.

Step 4 

show running-config

Verify your entries.

Step 5 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To disable the DHCP server and relay agent, use the no service dhcp global configuration command.

See the "Configuring DHCP" section of the "IP Addressing and Services" section of the Cisco IOS IP Configuration Guide, Release 12.2 from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Configuration Guides for these procedures:

•Checking (validating) the relay agent information

•Configuring the relay agent forwarding policy

Specifying the Packet Forwarding Address

If the DHCP server and the DHCP clients are on different networks or subnets, you must configure the switch with the ip helper-address address interface configuration command. The general rule is to configure the command on the Layer 3 interface closest to the client. The address used in the ip helper-address command can be a specific DHCP server IP address, or it can be the network address if other DHCP servers are on the destination network segment. Using the network address enables any DHCP server to respond to requests.

Beginning in privileged EXEC mode, follow these steps to specify the packet forwarding address:

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

interface vlan vlan-id

Create a switch virtual interface by entering a VLAN ID, and enter interface configuration mode.

Step 3 

ip address ip-address subnet-mask

Configure the interface with an IP address and an IP subnet.

Step 4 

ip helper-address address

Specify the DHCP packet forwarding address.

The helper address can be a specific DHCP server address, or it can be the network address if other DHCP servers are on the destination network segment. Using the network address enables other servers to respond to DHCP requests.

If you have multiple servers, you can configure one helper address for each server.

Step 5 

exit

Return to global configuration mode.

Step 6 

interface range port-range

or

interface interface-id

Configure multiple physical ports that are connected to the DHCP clients, and enter interface range configuration mode.

or

Configure a single physical port that is connected to the DHCP client, and enter interface configuration mode.

Step 7 

switchport mode access

Define the VLAN membership mode for the port.

Step 8 

switchport access vlan vlan-id

Assign the ports to the same VLAN as configured in Step 2.

Step 9 

end

Return to privileged EXEC mode.

Step 10 

show running-config

Verify your entries.

Step 11 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To remove the DHCP packet forwarding address, use the no ip helper-address address interface configuration command.

Enabling DHCP Snooping and Option 82

Beginning in privileged EXEC mode, follow these steps to enable DHCP snooping on the switch:

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

ip dhcp snooping

Enable DHCP snooping globally.

Step 3 

ip dhcp snooping vlan vlan-range

Enable DHCP snooping on a VLAN or range of VLANs. The range is 1 to 4094.

You can enter a single VLAN ID identified by VLAN ID number, a series of VLAN IDs separated by commas, a range of VLAN IDs separated by hyphens, or a range of VLAN IDs separated by entering the starting and ending VLAN IDs separated by a space.

Step 4 

ip dhcp snooping information option

Enable the switch to insert and to remove DHCP relay information (option-82 field) in forwarded DHCP request messages to the DHCP server. This is the default setting.

Step 5 

ip dhcp snooping information option format remote-id [string ASCII-string | hostname]

(Optional) Configure the remote-ID suboption.

You can configure the remote ID as

•String of up to 63 ASCII characters (no spaces)

•Configured hostname for the switch

Note If the hostname is longer than 63 characters, it is truncated to 63 characters in the remote-ID configuration.

The default remote ID is the switch MAC address.

Step 6 

ip dhcp snooping information option allow-untrusted

(Optional) If the switch is an aggregation switch connected to an edge switch, enable the switch to accept incoming DHCP snooping packets with option-82 information from the edge switch.

The default setting is disabled.

Note Enter this command only on aggregation switches that are connected to trusted devices.

Step 7 

interface interface-id

Specify the interface to be configured, and enter interface configuration mode.

Step 8 

ip dhcp snooping vlan vlan information option format-type circuit-id [override] string ASCII-string

(Optional) Configure the circuit-ID suboption for the specified interface.

Specify the VLAN and port identifier, using a VLAN ID in the range of 1 to 4094. The default circuit ID is the port identifier in the format vlan-mod-port.

You can configure the circuit ID to be a string of 3 to 63 ASCII characters (no spaces).

(Optional) Use the override keyword when you do not want the circuit-ID suboption inserted in TLV format to define subscriber information.

Step 9 

ip dhcp snooping trust

(Optional) Configure the interface as trusted or as untrusted. Use the no keyword to configure an interface to receive messages from an untrusted client. The default setting is untrusted.

Step 10 

ip dhcp snooping limit rate rate

(Optional) Configure the number of DHCP packets per second that an interface can receive. The range is 1 to 2048. By default, no rate limit is configured.

Note We recommend an untrusted rate limit of not more than 100 packets per second. If you configure rate limiting for trusted interfaces, you might need to increase the rate limit if the port is a trunk port assigned to more than one VLAN with DHCP snooping.

Step 11 

exit

Return to global configuration mode.

Step 12 

ip dhcp snooping verify mac-address

(Optional) Configure the switch to verify that the source MAC address in a DHCP packet received on untrusted ports matches the client hardware address in the packet. The default is to verify that the source MAC address matches the client hardware address in the packet.

Step 13 

end

Return to privileged EXEC mode.

Step 14 

show running-config

Verify your entries.

Step 15 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To disable DHCP snooping, use the no ip dhcp snooping global configuration command. To disable DHCP snooping on a VLAN or range of VLANs, use the no ip dhcp snooping vlan vlan-range global configuration command. To disable the insertion and the removal of the option-82 field, use the no ip dhcp snooping information option global configuration command. To configure an aggregation switch to drop incoming DHCP snooping packets with option-82 information from an edge switch, use the no ip dhcp snooping information option allow-untrusted global configuration command.

This example shows how to enable DHCP snooping globally and on VLAN 10 and to configure a rate limit of 100 packets per second on a port: 

Switch(config)# ip dhcp snooping

Switch(config)# ip dhcp snooping vlan 10

Switch(config)# ip dhcp snooping information option

Switch(config)# interface gigabitethernet2/0/1

Switch(config-if)# ip dhcp snooping limit rate 100

Enabling DHCP Snooping on Private VLANs

You can enable DHCP snooping on private VLANs. If DHCP snooping is enabled, the configuration is propagated to both a primary VLAN and its associated secondary VLANs. If DHCP snooping is enabled on the primary VLAN, it is also configured on the secondary VLANs.

If DHCP snooping is already configured on the primary VLAN and you configure DHCP snooping with different settings on a secondary VLAN, the configuration for the secondary VLAN does not take effect. You must configure DHCP snooping on the primary VLAN. If DHCP snooping is not configured on the primary VLAN, this message appears when you are configuring DHCP snooping on the secondary VLAN, such as VLAN 200: 

2w5d:%DHCP_SNOOPING-4-DHCP_SNOOPING_PVLAN_WARNING:DHCP Snooping configuration may not take 
effect on secondary vlan 200. DHCP Snooping configuration on secondary vlan is derived 
from its primary vlan.

The show ip dhcp snooping privileged EXEC command output shows all VLANs, including primary and secondary private VLANs, on which DHCP snooping is enabled.

Enabling the Cisco IOS DHCP Server Database

For procedures to enable and configure the Cisco IOS DHCP server database, see the "DHCP Configuration Task List" section in the "Configuring DHCP" chapter of the Cisco IOS IP Configuration Guide, Release 12.2 from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Configuration Guides.

Enabling the DHCP Snooping Binding Database Agent

Beginning in privileged EXEC mode, follow these steps to enable and configure the DHCP snooping binding database agent on the switch:

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

ip dhcp snooping database {flash[number]:/filename | ftp://user:password@host/filename | http://[[username:password]@]{hostname | host-ip}[/directory]
/image-name.tar | rcp://user@host/filename}| tftp://host/filename

Specify the URL for the database agent or the binding file by using one of these forms:

•flash[number]:/filename

(Optional) Use the number parameter to specify the stack member number of the stack master. The range for number is 1 to 9.

•ftp://user:password@host/filename

•http://[[username:password]@]{hostname | host-ip}[/directory]
/image-name.tar

•rcp://user@host/filename

•tftp://host/filename

Step 3 

ip dhcp snooping database timeout seconds

Specify (in seconds) how long to wait for the database transfer process to finish before stopping the process.

The default is 300 seconds. The range is 0 to 86400. Use 0 to define an infinite duration, which means to continue trying the transfer indefinitely.

Step 4 

ip dhcp snooping database write-delay seconds

Specify the duration for which the transfer should be delayed after the binding database changes. The range is from 15 to 86400 seconds. The default is 300 seconds (5 minutes).

Step 5 

end

Return to privileged EXEC mode.

Step 6 

ip dhcp snooping binding mac-address vlan vlan-id ip-address interface interface-id expiry seconds

(Optional) Add binding entries to the DHCP snooping binding database. The vlan-id range is from 1 to 4904. The seconds range is from 1 to 4294967295.

Enter this command for each entry that you add.

Note Use this command when you are testing or debugging the switch.

Step 7 

show ip dhcp snooping database [detail]

Display the status and statistics of the DHCP snooping binding database agent.

Step 8 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To stop using the database agent and binding files, use the no ip dhcp snooping database global configuration command. To reset the timeout or delay values, use the ip dhcp snooping database timeout seconds or the ip dhcp snooping database write-delay seconds global configuration command.

To clear the statistics of the DHCP snooping binding database agent, use the clear ip dhcp snooping database statistics privileged EXEC command. To renew the database, use the renew ip dhcp snooping database privileged EXEC command.

To delete binding entries from the DHCP snooping binding database, use the no ip dhcp snooping binding mac-address vlan vlan-id ip-address interface interface-id privileged EXEC command. Enter this command for each entry that you want to delete.

Displaying DHCP Snooping Information

To display the DHCP snooping information, use the privileged EXEC commands in Table 23-2:

Table 23-2 Commands for Displaying DHCP Information

Command
Purpose

show ip dhcp snooping

Displays the DHCP snooping configuration for a switch

show ip dhcp snooping binding

Displays only the dynamically configured bindings in the DHCP snooping binding database, also referred to as a binding table.

show ip dhcp snooping database

Displays the DHCP snooping binding database status and statistics.

show ip dhcp snooping statistics

Displays the DHCP snooping statistics in summary or detail form.

show ip source binding

Display the dynamically and statically configured bindings.


Note If DHCP snooping is enabled and an interface changes to the down state, the switch does not delete the statically configured bindings.

Understanding IP Source Guard

IPSG is a security feature that restricts IP traffic on nonrouted, Layer 2 interfaces by filtering traffic based on the DHCP snooping binding database and on manually configured IP source bindings. You can use IP source guard to prevent traffic attacks if a host tries to use the IP address of its neighbor.

You can enable IP source guard when DHCP snooping is enabled on an untrusted interface. After IPSG is enabled on an interface, the switch blocks all IP traffic received on the interface except for DHCP packets allowed by DHCP snooping. A port access control list (ACL) is applied to the interface. The port ACL allows only IP traffic with a source IP address in the IP source binding table and denies all other traffic.

Note The port ACL takes precedence over any router ACLs or VLAN maps that affect the same interface.

The IP source binding table bindings are learned by DHCP snooping or are manually configured (static IP source bindings). An entry in this table has an IP address with its associated MAC address and VLAN number. The switch uses the IP source binding table only when IP source guard is enabled.

IPSG is supported only on Layer 2 ports, including access and trunk ports.You can configure IPSG with source IP address filtering or with source IP and MAC address filtering.

•Source IP Address Filtering

•Source IP and MAC Address Filtering

•IP Source Guard for Static Hosts

Source IP Address Filtering

When IPSG is enabled with this option, IP traffic is filtered based on the source IP address. The switch forwards IP traffic when the source IP address matches an entry in the DHCP snooping binding database or a binding in the IP source binding table.

When a DHCP snooping binding or static IP source binding is added, changed, or deleted on an interface, the switch modifies the port ACL by using the IP source binding changes and re-applies the port ACL to the interface.

If you enable IPSG on an interface on which IP source bindings (dynamically learned by DHCP snooping or manually configured) are not configured, the switch creates and applies a port ACL that denies all IP traffic on the interface. If you disable IP source guard, the switch removes the port ACL from the interface.

Source IP and MAC Address Filtering

IP traffic is filtered based on the source IP and MAC addresses. The switch forwards traffic only when the source IP and MAC addresses match an entry in the IP source binding table.

When address filtering is enabled, the switch filters IP and non-IP traffic. If the source MAC address of an IP or non-IP packet matches a valid IP source binding, the switch forwards the packet. The switch drops all other types of packets except DHCP packets.

The switch uses port security to filter source MAC addresses. The interface can shut down when a port-security violation occurs.

IP Source Guard for Static Hosts

Note Do not use IPSG (IP source guard) for static hosts on uplink ports or trunk ports.

IPSG for static hosts extends the IPSG capability to non-DHCP and static environments. The previous IPSG used the entries created by DHCP snooping to validate the hosts connected to a switch. Any traffic received from a host without a valid DHCP binding entry is dropped. This security feature restricts IP traffic on nonrouted Layer 2 interfaces. It filters traffic based on the DHCP snooping binding database and on manually configured IP source bindings. The previous version of IPSG required a DHCP environment for IPSG to work.

IPSG for static hosts allows IPSG to work without DHCP. IPSG for static hosts relies on IP device tracking-table entries to install port ACLs. The switch creates static entries based on ARP requests or other IP packets to maintain the list of valid hosts for a given port. You can also specify the number of hosts allowed to send traffic to a given port. This is equivalent to port security at Layer 3.

IPSG for static hosts also supports dynamic hosts. If a dynamic host receives a DHCP-assigned IP address that is available in the IP DHCP snooping table, the same entry is learned by the IP device tracking table. In a stacked environment, when the master failover occurs, the IP source guard entries for static hosts attached to member ports are retained. When you enter the show ip device tracking all EXEC command, the IP device tracking table displays the entries as ACTIVE.

Note Some IP hosts with multiple network interfaces can inject some invalid packets into a network interface. The invalid packets contain the IP or MAC address for another network interface of the host as the source address. The invalid packets can cause IPSG for static hosts to connect to the host, to learn the invalid IP or MAC address bindings, and to reject the valid bindings. Consult the vender of the corresponding operating system and the network interface to prevent the host from injecting invalid packets.

IPSG for static hosts initially learns IP or MAC bindings dynamically through an ACL-based snooping mechanism. IP or MAC bindings are learned from static hosts by ARP and IP packets. They are stored in the device tracking database. When the number of IP addresses that have been dynamically learned or statically configured on a given port reaches a maximum, the hardware drops any packet with a new IP address. To resolve hosts that have moved or gone away for any reason, IPSG for static hosts leverages IP device tracking to age out dynamically learned IP address bindings. This feature can be used with DHCP snooping. Multiple bindings are established on a port that is connected to both DHCP and static hosts. For example, bindings are stored in both the device tracking database as well as in the DHCP snooping binding database.

Configuring IP Source Guard

•Default IP Source Guard Configuration

•IP Source Guard Configuration Guidelines

•Enabling IP Source Guard

•Configuring IP Source Guard for Static Hosts

Default IP Source Guard Configuration

By default, IP source guard is disabled.

IP Source Guard Configuration Guidelines

•You can configure static IP bindings only on nonrouted ports. If you enter the ip source binding mac-address vlan vlan-id ip-address interface interface-id global configuration command on a routed interface, this error message appears: 

Static IP source binding can only be configured on switch port.

•When IP source guard with source IP filtering is enabled on an interface, DHCP snooping must be enabled on the access VLAN for that interface.

•If you are enabling IP source guard on a trunk interface with multiple VLANs and DHCP snooping is enabled on all the VLANs, the source IP address filter is applied on all the VLANs.

Note If IP source guard is enabled and you enable or disable DHCP snooping on a VLAN on the trunk interface, the switch might not properly filter traffic.

•If you enable IP source guard with source IP and MAC address filtering, DHCP snooping and port security must be enabled on the interface. You must also enter the ip dhcp snooping information option global configuration command and ensure that the DHCP server supports option 82. When IP source guard is enabled with MAC address filtering, the DHCP host MAC address is not learned until the host is granted a lease. When forwarding packets from the server to the host, DHCP snooping uses option-82 data to identify the host port.

•When configuring IP source guard on interfaces on which a private VLAN is configured, port security is not supported.

•IP source guard is not supported on EtherChannels.

•You can enable this feature when 802.1x port-based authentication is enabled.

•If the number of ternary content addressable memory (TCAM) entries exceeds the maximum, the CPU usage increases.

•In a switch stack, if IP source guard is configured on a stack member interface and you remove the switch configuration by entering the no switch stack-member-number provision global configuration command, the interface static bindings are removed from the binding table. They are not removed from the running configuration. If you again provision the switch by entering the switch stack-member-number provision command, the binding is restored. To remove the binding from the running configuration, you must disable IP source guard before entering the no switch provision global configuration command. The configuration is also removed if the switch reloads while the interface is removed from the binding table. For more information about provisioned switches, see the "Stack Offline Configuration" section on page 5-6.

Enabling IP Source Guard

Begin in privileged EXEC mode.

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

interface interface-id

Specify the interface to be configured, and enter interface configuration mode.

Step 3 

ip verify source

or

ip verify source port-security

Enable IP source guard with source IP address filtering.

Enable IP source guard with source IP and MAC address filtering.

Note When you enable both IP source guard and Port Security by using the ip verify source port-security interface configuration command, there are two caveats:

•The DHCP server must support option 82, or the client is not assigned an IP address.

•The MAC address in the DHCP packet is not learned as a secure address. The MAC address of the DHCP client is learned as a secure address only when the switch receives non-DHCP data traffic.

Step 4 

exit

Return to global configuration mode.

Step 5 

ip source binding mac-address vlan vlan-id ip-address inteface interface-id

Add a static IP source binding.

Enter this command for each static binding.

Step 6 

end

Return to privileged EXEC mode.

Step 7 

show ip verify source [interface interface-id]

Verify the IP source guard configuration.

Step 8 

show ip source binding [ip-address] [mac-address] [dhcp-snooping | static] [inteface interface-id] [vlan vlan-id]

Display the IP source bindings on the switch, on a specific VLAN, or on a specific interface.

Step 9 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To disable IP source guard with source IP address filtering, use the no ip verify source interface configuration command.

To delete a static IP source binding entry, use the no ip source global configuration command.

This example shows how to enable IP source guard with source IP and MAC filtering on VLANs 10
and 11: 

Switch# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface gigabitethernet1/0/1

Switch(config-if)# ip verify source port-security

Switch(config-if)# exit

Switch(config)# ip source binding 0100.0022.0010 vlan 10 10.0.0.2 interface 
gigabitethernet1/0/1

Switch(config)# ip source binding 0100.0230.0002 vlan 11 10.0.0.4 interface 
gigabitethernet1/0/1

Switch(config)# end

Configuring IP Source Guard for Static Hosts

•Configuring IP Source Guard for Static Hosts on a Layer 2 Access Port

•Configuring IP Source Guard for Static Hosts on a Private VLAN Host Port

Configuring IP Source Guard for Static Hosts on a Layer 2 Access Port

Note You must configure the ip device tracking maximum limit-number interface configuration command globally for IPSG for static hosts to work. If you only configure this command on a port without enabling IP device tracking globally or by setting an IP device tracking maximum on that interface, IPSG with static hosts rejects all the IP traffic from that interface. This requirement also applies to IPSG with static hosts on a private VLAN host port.

Beginning in privileged EXEC mode:

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

ip device tracking

Turn on the IP host table, and globally enable IP device tracking.

Step 3 

interface interface-id

Enter interface configuration mode.

Step 4 

switchport mode access

Configure a port as access.

Step 5 

switchport access vlan vlan-id

Configure the VLAN for this port.

Step 6 

ip verify source tracking port-security

Enable IPSG for static hosts with MAC address filtering.

Note When you enable both IP source guard and port security by using the ip verify source port-security interface configuration command:

•The DHCP server must support option 82, or the client is not assigned an IP address.

•The MAC address in the DHCP packet is not learned as a secure address. The MAC address of the DHCP client is learned as a secure address only when the switch receives non-DHCP data traffic.

Step 7 

ip device tracking maximum number

Establish a maximum limit for the number of static IPs that the IP device tracking table allows on the port. The range is 1to 10. The maximum number is 10.

Note You must configure the ip device tracking maximum limit-number interface configuration command.

Step 8 

switchport port-security

(Optional) Activate port security for this port.

Step 9 

switchport port-security maximum value

(Optional) Establish a maximum of MAC addresses for this port.

Step 10 

end

Return to privileged EXEC mode.

Step 11 

show ip verify source interface interface-id

Verify the configuration and display IPSG permit ACLs for static hosts.

Step 12 

show ip device track all
[active | inactive] count

Verify the configuration by displaying the IP-to-MAC binding for a given host on the switch interface.

•all active—display only the active IP or MAC binding entries

•all inactive—display only the inactive IP or MAC binding entries

•all—display the active and inactive IP or MAC binding entries

This example shows how to stop IPSG with static hosts on an interface. 

Switch(config-if)# no ip verify source

Switch(config-if)# no ip device tracking max

This example shows how to enable IPSG with static hosts on a port. 

Switch(config)# ip device tracking

Switch(config)# ip device tracking max 10

Switch(config-if)# ip verify source tracking port-security

This example shows how to enable IPSG for static hosts with IP filters on a Layer 2 access port and to verify the valid IP bindings on the interface Gi0/3: 

Switch# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# ip device tracking

Switch(config)# interface gigabitethernet 0/3

Switch(config-if)# switchport mode access 

Switch(config-if)# switchport access vlan 10

Switch(config-if)# ip device tracking maximum 5

Switch(config-if)# ip verify source tracking

Switch(config-if)# end


Switch# show ip verify source

Interface  Filter-type  Filter-mode  IP-address       Mac-address        Vlan

---------  -----------  -----------  ---------------  -----------------  ----

Gi0/3      ip trk       active       40.1.1.24                           10   

Gi0/3      ip trk       active       40.1.1.20                           10  

Gi0/3      ip trk       active       40.1.1.21                           10

This example shows how to enable IPSG for static hosts with IP-MAC filters on a Layer 2 access port, to verify the valid IP-MAC bindings on the interface Gi0/3, and to verify that the number of bindings on this interface has reached the maximum: 

Switch# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# ip device tracking

Switch(config)# interface gigabitethernet 0/3

Switch(config-if)# switchport mode access 

Switch(config-if)# switchport access vlan 1

Switch(config-if)# ip device tracking maximum 5

Switch(config-if)# switchport port-security 

Switch(config-if)# switchport port-security maximum 5

Switch(config-if)# ip verify source tracking port-security 

Switch(config-if)# end


Switch# show ip verify source

Interface  Filter-type  Filter-mode  IP-address       Mac-address        Vlan

---------  -----------  -----------  ---------------  -----------------  ----

Gi0/3      ip-mac trk   active       40.1.1.24        00:00:00:00:03:04  1   

Gi0/3      ip-mac trk   active       40.1.1.20        00:00:00:00:03:05  1   

Gi0/3      ip-mac trk   active       40.1.1.21        00:00:00:00:03:06  1   

Gi0/3      ip-mac trk   active       40.1.1.22        00:00:00:00:03:07  1   

Gi0/3      ip-mac trk   active       40.1.1.23        00:00:00:00:03:08  1

This example displays all IP or MAC binding entries for all interfaces. The CLI displays all active as well as inactive entries. When a host is learned on a interface, the new entry is marked as active. When the same host is disconnected from that interface and connected to a different interface, a new IP or MAC binding entry displays as active as soon as the host is detected. The old entry for this host on the previous interface is marked as INACTIVE. 

Switch# show ip device tracking all 

IP Device Tracking = Enabled

IP Device Tracking Probe Count = 3

IP Device Tracking Probe Interval = 30

---------------------------------------------------------------------

  IP Address     MAC Address   Vlan  Interface              STATE    

---------------------------------------------------------------------

200.1.1.8       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.9       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.10      0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.1       0001.0600.0000  9    GigabitEthernet0/2     ACTIVE

200.1.1.1       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.2       0001.0600.0000  9    GigabitEthernet0/2     ACTIVE

200.1.1.2       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.3       0001.0600.0000  9    GigabitEthernet0/2     ACTIVE

200.1.1.3       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.4       0001.0600.0000  9    GigabitEthernet0/2     ACTIVE

200.1.1.4       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.5       0001.0600.0000  9    GigabitEthernet0/2     ACTIVE

200.1.1.5       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.6       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.7       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

This example displays all active IP or MAC binding entries for all interfaces: 

Switch# show ip device tracking all active

IP Device Tracking = Enabled

IP Device Tracking Probe Count = 3

IP Device Tracking Probe Interval = 30

---------------------------------------------------------------------

  IP Address     MAC Address   Vlan  Interface              STATE    

---------------------------------------------------------------------

200.1.1.1       0001.0600.0000  9    GigabitEthernet0/1     ACTIVE

200.1.1.2       0001.0600.0000  9    GigabitEthernet0/1     ACTIVE

200.1.1.3       0001.0600.0000  9    GigabitEthernet0/1     ACTIVE

200.1.1.4       0001.0600.0000  9    GigabitEthernet0/1     ACTIVE

200.1.1.5       0001.0600.0000  9    GigabitEthernet0/1     ACTIVE

This example displays all inactive IP or MAC binding entries for all interfaces. The host was first learned on GigabitEthernet 0/1 and then moved to GigabitEthernet 0/2. the IP or MAC binding entries learned on GigabitEthernet 0/1 are marked as inactive. 

Switch# show ip device tracking all inactive

IP Device Tracking = Enabled

IP Device Tracking Probe Count = 3

IP Device Tracking Probe Interval = 30

---------------------------------------------------------------------

  IP Address     MAC Address   Vlan  Interface              STATE    

---------------------------------------------------------------------

200.1.1.8       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.9       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.10      0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.1       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.2       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.3       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.4       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.5       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.6       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

200.1.1.7       0001.0600.0000  8    GigabitEthernet0/1     INACTIVE

This example displays the count of all IP device tracking host entries for all interfaces: 

Switch# show ip device tracking all count

Total IP Device Tracking Host entries: 5

---------------------------------------------------------------------

  Interface           Maximum Limit           Number of Entries      

---------------------------------------------------------------------

Gi0/3                  5

Configuring IP Source Guard for Static Hosts on a Private VLAN Host Port

Note You must globally configure the ip device tracking maximum limit-number interface configuration command globally for IPSG for static hosts to work. If you only configure this command on a port without enabling IP device tracking globally or setting an IP device tracking maximum on that interface, IPSG with static hosts will reject all the IP traffic from that interface. This requirement also applies to IPSG with static hosts on a Layer 2 access port.

Beginning in privileged EXEC mode, follow these steps to configure IPSG for static hosts with IP filters on a Layer 2 access port:

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

vlan vlan-id1

Enter VLAN configuration mode.

Step 3 

private-vlan primary

Establish a primary VLAN on a private VLAN port.

Step 4 

exit

Exit VLAN configuration mode.

Step 5 

vlan vlan-id2

Enter configuration VLAN mode for another VLAN.

Step 6 

private-vlan isolated

Establish an isolated VLAN on a private VLAN port.

Step 7 

exit

Exit VLAN configuration mode.

Step 8 

vlan vlan-id1

Enter configuration VLAN mode.

Step 9 

private-vlan association 201

Associate the VLAN on an isolated private VLAN port.

Step 10 

exit

Exit VLAN configuration mode.

Step 11 

interface fastEthernet interface-id

Enter interface configuration mode.

Step 12 

switchport mode private-vlan host

(Optional) Establish a port as a private VLAN host.

Step 13 

switchport private-vlan host-association vlan-id1 vlan-id2

(Optional) Associate this port with the corresponding private VLAN.

Step 14 

ip device tracking maximum number

Establish a maximum for the number of static IPs that the IP device tracking table allows on the port.

The maximum is 10.

Note You must globally configure the ip device tracking maximum number interface command for IPSG for static hosts to work.

Step 15 

ip verify source tracking [port-security]

Activate IPSG for static hosts with MAC address filtering on this port.

Step 16 

end

Exit configuration interface mode.

Step 17 

show ip device tracking all

Verify the configuration.

Step 18 

show ip verify source interface interface-id

Verify the IP source guard configuration. Display IPSG permit ACLs for static hosts.

This example shows how to enable IPSG for static hosts with IP filters on a private VLAN host port: 

Switch(config)# vlan 200

Switch(config-vlan)# private-vlan primary

Switch(config-vlan)# exit

Switch(config)# vlan 201

Switch(config-vlan)# private-vlan isolated 

Switch(config-vlan)# exit

Switch(config)# vlan 200

Switch(config-vlan)# private-vlan association 201

Switch(config-vlan)# exit

Switch(config)# int fastEthernet 4/3

Switch(config-if)# switchport mode private-vlan host 

Switch(config-if)# switchport private-vlan host-association 200 201

Switch(config-if)# ip device tracking maximum 8

Switch(config-if)# ip verify source tracking


Switch# show ip device tracking all

IP Device Tracking = Enabled

IP Device Tracking Probe Count = 3

IP Device Tracking Probe Interval = 30

---------------------------------------------------------------------

  IP Address     MAC Address   Vlan  Interface              STATE    

---------------------------------------------------------------------

40.1.1.24       0000.0000.0304  200  FastEthernet0/3        ACTIVE

40.1.1.20       0000.0000.0305  200  FastEthernet0/3        ACTIVE

40.1.1.21       0000.0000.0306  200  FastEthernet0/3        ACTIVE

40.1.1.22       0000.0000.0307  200  FastEthernet0/3        ACTIVE

40.1.1.23       0000.0000.0308  200  FastEthernet0/3        ACTIVE

The output shows the five valid IP-MAC bindings that have been learned on the interface Fa0/3. For the private VLAN cases, the bindings are associated with primary VLAN ID. So, in this example, the primary VLAN ID, 200, is shown in the table. 

Switch# show ip verify source

Interface  Filter-type  Filter-mode  IP-address       Mac-address        Vlan

---------  -----------  -----------  ---------------  -----------------  ----

Fa0/3      ip trk       active       40.1.1.23                           200 

Fa0/3      ip trk       active       40.1.1.24                           200 

Fa0/3      ip trk       active       40.1.1.20                           200 

Fa0/3      ip trk       active       40.1.1.21                           200 

Fa0/3      ip trk       active       40.1.1.22                           200 

Fa0/3      ip trk       active       40.1.1.23                           201 

Fa0/3      ip trk       active       40.1.1.24                           201 

Fa0/3      ip trk       active       40.1.1.20                           201 

Fa0/3      ip trk       active       40.1.1.21                           201 

Fa0/30/3      ip trk       active       40.1.1.22                           201

The output shows that the five valid IP-MAC bindings are on both the primary and secondary VLAN.

Displaying IP Source Guard Information

To display the IP source guard information, use one or more of the privileged EXEC commands in Table 23-3:

Table 23-3 Commands for Displaying IP Source Guard Information

Command
Purpose

show ip device tracking

Display the active IP or MAC binding entries for all interfaces.

show ip source binding

Display the IP source bindings on a switch.

show ip verify source

Display the IP source guard configuration on the switch.


Understanding DHCP Server Port-Based Address Allocation

DHCP server port-based address allocation is a feature that enables DHCP to maintain the same IP address on an Ethernet switch port regardless of the attached device client identifier or client hardware address.

When Ethernet switches are deployed in the network, they offer connectivity to the directly connected devices. In some environments, such as on a factory floor, if a device fails, the replacement device must be working immediately in the existing network. With the current DHCP implementation, there is no guarantee that DHCP would offer the same IP address to the replacement device. Control, monitoring, and other software expect a stable IP address associated with each device. If a device is replaced, the address assignment should remain stable even though the DHCP client has changed.

When configured, the DHCP server port-based address allocation feature ensures that the same IP address is always offered to the same connected port even as the client identifier or client hardware address changes in the DHCP messages received on that port. The DHCP protocol recognizes DHCP clients by the client identifier option in the DHCP packet. Clients that do not include the client identifier option are identified by the client hardware address. When you configure this feature, the port name of the interface overrides the client identifier or hardware address and the actual point of connection, the switch port, becomes the client identifier.

In all cases, by connecting the Ethernet cable to the same port, the same IP address is allocated through DHCP to the attached device.

The DHCP server port-based address allocation feature is only supported on a Cisco IOS DHCP server and not a third-party server.

Configuring DHCP Server Port-Based Address Allocation

This section contains this configuration information:

•Default Port-Based Address Allocation Configuration

•Port-Based Address Allocation Configuration Guidelines

•Enabling DHCP Server Port-Based Address Allocation

Default Port-Based Address Allocation Configuration

By default, DHCP server port-based address allocation is disabled.

Port-Based Address Allocation Configuration Guidelines

These are the configuration guidelines for DHCP port-based address allocation:

•Only one IP address can be assigned per port.

•Reserved addresses (preassigned) cannot be cleared by using the clear ip dhcp binding global configuration command.

•Preassigned addresses are automatically excluded from normal dynamic IP address assignment. Preassigned addresses cannot be used in host pools, but there can be multiple preassigned addresses per DHCP address pool.

•To restrict assignments from the DHCP pool to preconfigured reservations (unreserved addresses are not offered to the client and other clients are not served by the pool), you can enter the reserved-only DHCP pool configuration command.

Enabling DHCP Server Port-Based Address Allocation

Beginning in privileged EXEC mode, follow these steps to globally enable port-based address allocation and to automatically generate a subscriber identifier on an interface.

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

ip dhcp use subscriber-id client-id

Configure the DHCP server to globally use the subscriber identifier as the client identifier on all incoming DHCP messages.

Step 3 

ip dhcp subscriber-id interface-name

Automatically generate a subscriber identifier based on the short name of the interface.

A subscriber identifier configured on a specific interface takes precedence over this command.

Step 4 

interface interface-id

Specify the interface to be configured, and enter interface configuration mode.

Step 5 

ip dhcp server use subscriber-id client-id

Configure the DHCP server to use the subscriber identifier as the client identifier on all incoming DHCP messages on the interface.

Step 6 

end

Return to privileged EXEC mode.

Step 7 

show running config

Verify your entries.

Step 8 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

After enabling DHCP port-based address allocation on the switch, use the ip dhcp pool global configuration command to preassign IP addresses and to associate them to clients. To restrict assignments from the DHCP pool to preconfigured reservations, you can enter the reserved-only DHCP pool configuration command. Unreserved addresses that are part of the network or on pool ranges are not offered to the client, and other clients are not served by the pool. By entering this command, users can configure a group of switches with DHCP pools that share a common IP subnet and that ignore requests from clients of other switches.

Beginning in privileged EXEC mode follow these steps to preassign an IP address and to associate it to a client identified by the interface name.

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

ip dhcp pool poolname

Enter DHCP pool configuration mode, and define the name for the DHCP pool. The pool name can be a symbolic string (such as Engineering) or an integer (such as 0).

Step 3 

network network-number [mask | /prefix-length]

Specify the subnet network number and mask of the DHCP address pool.

Step 4 

address ip-address client-id string [ascii]

Reserve an IP address for a DHCP client identified by the interface name.

string—can be an ASCII value or a hexadecimal value.

Step 5 

reserved-only

(Optional) Use only reserved addresses in the DHCP address pool. The default is to not restrict pool addresses.

Step 6 

end

Return to privileged EXEC mode.

Step 7 

show ip dhcp pool

Verify DHCP pool configuration.

Step 8 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To disable DHCP port-based address allocation, use the no ip dhcp use subscriber-id client-id global configuration command. To disable the automatic generation of a subscriber identifier, use the no ip dhcp subscriber-id interface-name global configuration command. To disable the subscriber identifier on an interface, use the no ip dhcp server use subscriber-id client-id interface configuration command.

To remove an IP address reservation from a DHCP pool, use the no address ip-address client-id string DHCP pool configuration command. To change the address pool to nonrestricted, enter the no reserved-only DHCP pool configuration command.

In this example, a subscriber identifier is automatically generated, and the DHCP server ignores any client identifier fields in the DHCP messages and uses the subscriber identifier instead. The subscriber identifier is based on the short name of the interface and the client preassigned IP address 10.1.1.7. 

switch# show running config

Building configuration...

Current configuration : 4899 bytes

!

version 12.2

!

hostname switch

!

no aaa new-model

clock timezone EST 0

ip subnet-zero

ip dhcp relay information policy removal pad

no ip dhcp use vrf connected

ip dhcp use subscriber-id client-id

ip dhcp subscriber-id interface-name

ip dhcp excluded-address 10.1.1.1 10.1.1.3

!         

ip dhcp pool dhcppool

 network 10.1.1.0 255.255.255.0

 address 10.1.1.7 client-id "Et1/0" ascii

<output truncated>

This example shows that the preassigned address was correctly reserved in the DHCP pool: 

switch# show ip dhcp pool dhcppool

Pool dhcp pool:

 Utilization mark (high/low) : 100 / 0

 Subnet size (first/next) : 0 / 0 

 Total addresses : 254

 Leased addresses : 0

 Excluded addresses : 4

 Pending event : none

 1 subnet is currently in the pool:

 Current index   IP address range         Leased/Excluded/Total

 10.1.1.1        10.1.1.1 - 10.1.1.254     0     / 4 / 254 

 1 reserved address is currently in the pool

 Address         Client

 10.1.1.7 Et1/0

For more information about configuring the DHCP server port-based address allocation feature, go to Cisco.com, and enter Cisco IOS IP Addressing Services in the Search field to access the Cisco IOS software documentation. You can also access the documentation at this URL:

http://www.cisco.com/en/US/docs/ios/ipaddr/command/reference/iad_book.html

Displaying DHCP Server Port-Based Address Allocation

To display the DHCP server port-based address allocation information, use one or more of the privileged EXEC commands in Table 23-4:

Table 23-4 Commands for Displaying DHCP Port-Based Address Allocation Information

Command
Purpose

show interface interface id

Display the status and configuration of a specific interface.

show ip dhcp pool

Display the DHCP address pools.

show ip dhcp binding

Display address bindings on the Cisco IOS DHCP server.