Installation Guidelines

Observe these guidelines when removing or installing a power-supply module:

A power-supply module that is only partially connected to the switch disrupts the system operation.

Warning: Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Note: You can order the blank cover (part number RPS-CG-COVER=).

Warning: Do not reach into a vacant slot while installing or removing a module. Exposed circuitry is an energy hazard. Statement 206

Warning: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning: Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning. Statement 1088

Installing a Power-Supply Module

This procedure is for installing a power-supply module in the PSU1 or PSU2 slot.

Warning: The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077

Warning: This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

Caution: Equipment installation must comply with local and national electrical codes.

Equipment That You Need

■Ratcheting torque flathead screwdriver that exerts up to 15-inch pound (in-lb) of torque

■Ring, spade, or flanged spade terminal (terminals should be insulated)

–Ring terminal (such as Tyco part number 2-34158-1 for 16 – 14 AWG or 2-34852-1 for 12 – 10 AWG wire)

–Spade terminal (such as Tyco part number 54367-2 for 16 – 14 AWG wire)

–Flanged spade terminal (such as Tyco part number 2-324165-1 for 16 – 14 AWG wire or 1-324581-1 for 12 – 10 AWG wire)

For IP-30 compliance:

■Use the 16-14 AWG wire and appropriate terminals for the AC or high-voltage DC power supply

■Use the12-10 AWG wire and appropriate terminals for the low-voltage DC power supply

■Crimping tool (such as Thomas & Bett part number WT2000, ERG-2001)

■6-gauge copper ground wire (such as Belden part number 9906)

■12-AWG wire (minimum) for the low-voltage power-supply module and 16-AWG (minimum) wire for the high-voltage power-supply module

■For power source connections, use wires rated for at least 194°F (90°C).

■UL- and CSA-rated style 1007 or 1569 twisted-pair copper wire (such as Belden part number 9318)

■Wire-stripping tools for stripping 6-, 10-, 12-, 14-, and 16-gauge wires.

■Number-2 Phillips screwdriver

■Flat-blade screwdriver

Grounding the Switch

Follow the grounding procedures at your site and observe these warnings:

Warning: This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning: When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Caution: Follow the grounding procedure instructions, and use a UL-listed lug (included with the switch) for number-6 AWG wire and 10-32 ground-lug screws.

Note: You can use the grounding lug to attach a wrist strap for ESD protection during servicing.

Follow these steps to install a dual-hole lug on the switch. Be sure to follow any grounding requirements at your site.

1. Use a Phillips screwdriver or a ratcheting torque screwdriver with a Phillips head to remove the ground screw from the cable side of the switch. You need the screw in Step 4.

2. Strip the 6-gauge ground wire to 0.5 inch (12.7 mm) ± 0.02 inch (0.5 mm). See Figure 38. Stripping more than the recommended amount of wire can leave exposed wire from the connector.

Figure 38 Stripping the Ground Wire

3. Insert the ground wire into the terminal lug, and crimp the terminal to the wire. (see Figure 39).

Figure 39 Crimping the Terminal Lug

4. Slide the ground screw from Step 1 through the terminal lug. Insert the ground screws into the opening on the cable side.

Figure 40 Attaching the Terminal Lug

5. Use a ratcheting torque screwdriver to tighten the ground screws to 30 in-lb (± 2 in-lb).

6. Attach the other end of the ground wire to a grounded bare metal surface, such as a ground bus or a grounded bare rack.

Installing the Power-Supply Module in the Switch

1. Ensure that the power is off at the AC or DC circuits.

Locate the circuit breakers, turn them OFF, and tape them in the OFF position.

Warning: If the power is not off at the AC or DC circuit breaker, do not touch the power-input terminal.

2. Use a Phillips screwdriver to loosen the two captive screws of the blank power-supply module and gently pull it out. See Figure 41 and Figure 42.

Figure 41 Loosen the Screws on the Power Supply Blank

Figure 42 Remove the Power Supply Blank

3. Insert the power-supply module into the slot, and gently push it in. See Figure 43.

Note: Ensure that the power supply module is flush with the switch.

Figure 43 Insert the Power-Supply Module

4. Use a ratcheting torque screwdriver to torque each screw to 8–10 in-lb.

Wiring the Power Source

Before you wire the power source, review these warnings:

Warning: This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

■ AC: 5 A, DC: 15 A Statement 1005

Warning: A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.
Statement 1022

Warning: Only trained and qualified personnel should be allowed to install or replace this equipment.
Statement 1030

Warning: Hazardous voltage or energy may be present on power terminals. Always replace cover when terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement 1086

1. Ensure that the power is off at the AC or DC circuits.

Locate the circuit breakers, turn them OFF, and tape them in the OFF position.

Warning: If the power is not off at the AC or DC circuit breaker, do not touch the power-input terminal.

Note: Do not connect the switch to a power source that has an ON/OFF switch.

2. Use a Phillips screwdriver to loosen the captive screw on the power-input terminal, and open the cover.

Figure 44 Opening the Power-Input Terminal Cover

The terminal screws labels are on the power-input terminal cover. See Figure 45.

Figure 45 Power-Input Terminal

Note: The power-supply module 1 connection is labeled PSU1, and the power-supply module 2 connection is labeled PSU2. Make sure that you connect the wires to the correct terminal screws.

3. Use twisted-pair copper wire (14- to 18-AWG) to connect from the power-input terminal to the power source.

Note: Use 12-AWG (minimum) for the low-voltage DC power supply module. Use 16-AWG (minimum) for the high-voltage AC or DC power supply module.

4. Strip each of the two wires to 0.25 inch (6.3 mm) ± 0.02 inch (0.5 mm).

Note: Do not strip more than 0.27 inch (6.8 mm) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the connector after installation.

Figure 46 Stripping the Input Power Source Wire

5. Insert the wire into a spade terminal, and crimp it to the wire.

You can also use a ring or flanged spade terminal as listed in the Equipment That You Need.

Figure 47 Crimping the Spade Terminal Lug

6. Loosen the terminal screw, and slide the terminal under the screw and washer. See Figure 49.

Note: Use the appropriate terminal screws based on power supply type: high-voltage (AC or DC) or low-voltage (DC).

7. Make the power connection:

AC Power Connection

■Connect the line wire into the terminal screw labeled L and the neutral wire into the terminal screw labeled N to complete the AC connection.

Figure 48 Connecting the Wires to the High-Voltage AC Power (PSU1)

DC Power Connection

■Connect the positive wire into the terminal screw labeled “ +”, and the negative wire into the terminal screw labeled “ – ”.

Low-voltage DC Power-Supply Module

■Connect the wires to the terminals labeled Lo.

High-voltage DC Power-Supply Module

■Connect the wires to the terminals labeled Hi.

Note: Ensure that you cannot see any wire lead. Only wire with insulation should extend from the terminal screw.

Figure 49 Connecting the Wires to the Low-Voltage DC Power (PSU2)

8. Torque the captive screws (above the wires) to 8.5 in-lb (± 0.5 in-lb).

9. Complete the power connection:

AC Power Connection

■Connect the other end of the line wire (the one connected to L) to the line terminal on the AC-power source, and connect the other end of the neutral wire (the one connected to N) to the neutral terminal on the AC power source.

DC Power Connection

■Connect the other end of the positive wire (the one connected to “ +”) to the positive terminal on the DC-power source, and connect the other end of the negative wire (the one connected to “ –”) to the negative terminal on the DC power source.

Note: Ensure that you cannot see any wire lead. Only wire with insulation should extend from the terminal screw.

If you have two power supplies, repeat steps 1 through 10.

10. Close the power-input terminal cover.

11. Use a ratcheting torque screwdriver to torque the screw to 6–8 in-lb.

12. Turn on the power at the AC or DC circuit.

13. Verify that the PSU1 or PSU2 LED on the switch and PSU OK LED on the power-supply module are green.

See the switch software guide for information on how to configure the power supply settings.