setup

(Optional) Interactive setup tool for configuring Cisco Unified IP Phone 7910s, 7940s, and 7960s in Cisco Unified CME.

12.1(5)YD

Cisco ITS 1.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

12.2(15)ZJ

Cisco CME 3.0

The setup keyword was added.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

Do you want to setup DHCP service for your IP phones? [yes/no]:

If you respond yes, you see the following prompts:

IP network for telephony-service DHCP  Pool:
Subnet mask for DHCP network : 
TFTP Server IP address (Option 150) :
Default Router for DHCP Pool :

• Yes—Configures the Cisco Unified CME router to act as a Dynamic Host Configuration Protocol (DHCP) server, automatically providing IP addresses to your IP phones and provisioning the default gateway and TFTP IP addresses to be used by the phones. This method creates a single pool of IP addresses. If you need a pool for non-IP phones or if the Cisco router cannot act as the DHCP router, answer no and manually define the DHCP server.
• No—Indicates that you have already configured DHCP or static IP addresses for the IP phones.

Do you want to start telephony-service setup? [yes/no]:

• Yes—Starts the interactive setup tool for configuring Cisco Unified IP Phone 7910s, 7940s, and 7960s.
• No—Terminates the Cisco CME setup tool.

Enter the IP source address for Cisco CallManager Express:
Enter the Skinny Port for Cisco CallManager Express:  [2000]:

IP address on which the router provides Cisco Unified CME services, usually the default gateway for the IP subnet that you are using for the IP phones, and the port for Skinny Client Control Protocol (SCCP) messages.

How many IP phones do you want to configure : [0]:

Enter the maximum number of IP phones that this Cisco Unified CME system will support. This number can be increased later, to the maximum allowed for this version and your router.

Do you want dual-line extensions assigned to phones? [yes for dual-line / no for single-line]:

• Yes—Each newly registering IP phones is assigned a single number that is associated with a single phone button. The system generates a dual-line ephone-dn entry for each ephone-dn.
• No—IP phones are linked directly to one or more PSTN trunk lines. Using keyswitch mode requires manual configuration in addition to using the Cisco CME setup tool. The system generates two ephone-dn entries for each ephone-dn, and they are both assigned to a single phone.

What language do you want on IP phones?
      0  English
      1  French
      2  German
      3  Russian
      4  Spanish
      5  Italian
      6  Dutch
      7  Norwegian
      8  Portuguese
      9  Danish
      10  Swedish
 [0]:

Language for IP phone displays, selected from the list.

• Default is 0, English.

Which Call Progress tone set do you want on IP phones :     
      0  United States
      1  France
      2  Germany
      3  Russia
      4  Spain
      5  Italy
      6  Netherlands
      7  Norway
      8  Portugal
      9  UK
    10  Denmark
    11  Switzerland
    12  Sweden
    13  Austria
    14  Canada
[0]:

Locale for the tone set used to indicate call status or progress, selected from the list.

• Default is 0, United States.

What is the first extension number you want to configure :[0]:

First number in pool of extension numbers to be created for IP phones connected to the Cisco router to be configured.

• Starting with this number, remaining extension numbers are automatically configured in a contiguous manner.
• This number must be compatible with your telephone number plan and if you use Direct Inward Dialing (DID) service, with public switched telephone network (PSTN) numbering requirements.

Do you have Direct-Inward-Dial service for all your phones? [yes/no]:

• Yes—If you have trunk access to public telephone service by ISDN or VoIP for all extension numbers. The system creates an appropriate dial plan.
• No—If you have simple analog phone lines only (for example, foreign exchange office [FXO] interfaces) or if you have trunk access for some lines but not all lines.

If you answer yes to the previous question, you see the following prompt:

Enter the full E.164 number for the first phone:

Complete ten-digit telephone number, including area code, that corresponds to the first extension number.

Do you want to forward calls to a voice message service? [yes/no]:

• Yes—To forward calls to a single voice message service number when an IP phone is busy or does not answer. All phone extensions forward their calls to the same voice message service pilot number.
• No—Not to forward calls to a single voice message service number. Answer no if you do not have a voice message system or if you want to customize call-forwarding behavior for each extension.

If you answer yes to the previous question, you see the following prompt:

Enter the extension or pilot number of the voice message service:

Voice message service pilot number.

• This step can be ignored during the setup dialog and manually configured later.

Call forward No Answer Timeout: [18]:

Timeout, in seconds, after which to forward calls to voice mail if they are not answered.

• Default is 18.

Do you wish to change any of the above information? [yes/no]:

• Yes—Starts the dialog over again without implementing any of the answers that you previously gave.
• No—Uses specified values to automatically build basic configuration for Cisco Unified IP Phone 7910s, 7940s, and 7960s in Cisco Unified CME.

Adds a new Cisco Unified SIP IP phone to Cisco Unified CME.

template tag

Creates a basic configuration template that supports all the configurations available on the voice register template. Range: 1 to 10.

15.6(3)M

16.3.1

Cisco Unified CME 11.5

This command was introduced.

service-enable (auto-register)

Temporarily disables the auto registration process, but retains the password and DN range configurations. Once auto-register command is entered, the service is enabled by default.

password (auto-register)

Configures the mandatory password that administrator sets for auto registration of SIP phones on Unified CME.

auto-assign (auto-register)

Configures the mandatory range of directory numbers for phones auto registering on Unified CME.

auto-register

Enables automatic registration of SIP phones with the Cisco Unified CME system.

auto-reg-ephone

Enables automatic registration of ephones with the Cisco Unified CME system.

template-tag

The template tag that was created with the voice register template command in voice register global configuration mode. Range is 1 to 5.

12.4(4)T

Cisco CME 3.4

This command was introduced.

voice register template

Enters voice register template configuration mode and defines a template of common parameters for SIP phones.

flash:

Router flash memory.

slot0:

Router slot 0 memory.

tftp://

External TFTP server.

url

URL for external TFTP server.

12.4(4)T

Cisco CME 3.4

This command was introduced.

create profile (voice register global)

Generates the configuration profiles required for SIP phones.

reset (voice register global)

Performs a “hard” reboot similar to a power-off-power-on sequence for all SIP phones in Cisco Unified CME, including contacting the Dynamic Host Configuration Protocol (DHCP) server and the TFTP server for updated information.

label

Name of a configured PKI trustpoint with a valid certificate.

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

12

Selects a 12-hour clock. This is the default.

24

Selects a 24-hour clock.

12.2(2)XT

Cisco ITS 2.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

date-format

Selects a format to display the date on Cisco IP phones.

12

Sets time in a 12-hour (AM/PM) clock.

24

Sets time in a 24-hour clock.

12.4(4)T

Cisco CME 3.4

This command was introduced.

voice register global

Enters voice register global configuration mode in order to set global parameters for all supported Cisco SIP phones in a Cisco CME or Cisco SIP SRST environment.

seconds

Number of seconds. Range: 3 to 60000. You can enter a different value for each hop between ephone-dns in a hunt group. If you enter a single value, the value is applied to each hop between ephone-dns in a hunt group.

12.2(15)ZJ

Cisco CME 3.0

This command was introduced.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

12.4(4)XC

Cisco Unified CME 4.0

This command was modified to accept multiple arguments that correspond to the number of ephone-dns configured in the hunt group.

12.4(9)T

Cisco Unified CME 4.0

This command with modifications up was integrated into Cisco IOS Release 12.4(9)T.

final

Defines the last ephone-dn in an ephone hunt group.

hops

Defines the number of times that a call is redirected to the next ephone-dn in a peer ephone-hunt-group list before proceeding to the final ephone-dn.

list

Defines the ephone-dns that participate in an ephone hunt group.

max-redirect

Changes the current number of allowable redirects in a Cisco Unified CME system.

max-timeout

Sets the maximum combined timeout for the no-answer periods for all ephone-dns in an ephone-hunt list,

no-reg (ephone-hunt)

Specifies that the pilot number of an ephone hunt group should not register with the H.323 gatekeeper.

pilot

Defines the ephone-dn that callers dial to reach an ephone hunt group.

preference (ephone-hunt)

Sets preference order for the ephone-dn associated with an ephone-hunt-group pilot number.

seconds

Number of seconds. Range is 3 to 60000. Default is 180.

12.4(4)T

Cisco CME 3.4

This command was introduced.

call-forward noan

Enables call forwarding so that incoming calls to an extension (ephone-dn) that does not answer are forwarded to another number.

final (voice hunt-group)

Defines the last extension in a voice hunt group.

hops (voice hunt-group)

Defines the number of times that a call is redirected to the next directory number in a peer voice hunt-group list before proceeding to the final directory number.

list (voice hunt-group)

Defines the directory numbers that participate in a hunt group.

seconds

Number of seconds after connection before a call is disconnected from a busy signal. Range is from 0 to 30 seconds. Default is 10.

12.2(8)T

Cisco ITS 2.0

This command was introduced.

telephony-service

Enters telephony-service configuration mode.

seconds

Interdigit timeout duration for Cisco IP phones, in seconds. Range is from 2 to 120. Default is 10.

12.2(2)XB

Cisco ITS 1.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

timeouts interdigit (voice-port)

Configures the interdigit timeout value for a specified voice port.

seconds

Interdigit timeout duration for Cisco SIP phones, in seconds. Range is from 2 to 120. Default is 10.

Cisco IOS XE Everest 16.4.1

Cisco Unified CME 11.6

This command was introduced.

timeouts interdigit (telephoy-service)

Configures the interdigit timeout value for a SCCP phone in Cisco Unified CME system.

seconds

Duration, in seconds, between night-service notification bells. Range: 4 to 30. Default: 12.

12.4(11)XW5

Cisco Unified CME 4.2

This command was introduced.

night-service bell (ephone)

Marks an IP phone to receive night-service bell notification when incoming calls are received during night-service time periods on ephone-dns that are marked for night service.

night-service bell (ephone-dn)

Marks an ephone-dn to send night-service bell notification to designated IP phones during night-service time periods.

seconds

Duration, in seconds, for which the Cisco CME system allows ringing to continue if a call is not answered. Range is from 5 to 60000. Default is 180.

12.2(15)ZJ

Cisco CME 3.0

This command was introduced.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

telephony-service

Enters telephony-service configuration mode.

seconds

Duration, in seconds, to wait before recalling a transferred call. Range: 1 to 1800. Default: 0 (disabled).

12.4(15)XZ

Cisco Unified CME 4.3

This command was introduced.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

call-forward busy

Enables call forwarding so that incoming calls to a busy extension (ephone-dn) are forwarded to another extension.

call-forward noan

Enables call forwarding so that incoming calls to an extension (ephone-dn) that does not answer are forwarded to another number.

transfer-mode

Specifies the call transfer method for an individual directory number.

transfer-system

Specifies the call transfer method globally for all directory numbers.

trunk

Associates an ephone-dn with a foreign exchange office (FXO) port.

seconds

Duration, in seconds, to wait before recalling a transferred call. Range: 1 to 1800. Default: 0 (disabled).

Cisco IOS XE Everest 16.4.1

Cisco Unified CME 11.6

This command was introduced.

timeouts transfer-recall(Ephone-dn (config-ephone-dn) and Telephony-service configuration (config-telephony)

Enables Cisco Unified CME to recall a transferred call if the transfer-to party does not answer or is busy.

seconds

Duration, in seconds, to wait before recalling a transferred call. Range: 1 to 1800. Default: 0 (disabled).

Cisco IOS XE Everest 16.4.1

Cisco Unified CME 11.6

This command was introduced.

timeouts transfer-recall(Ephone-dn (config-ephone-dn) and Telephony-service configuration (config-telephony)

Enables Cisco Unified CME to recall a transferred call if the transfer-to party does not answer or is busy.

12.2(2)XT

Cisco ITS 2.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

dn-webedit

Enables adding of directory numbers through a web interface.

telephony-service

Enters telephony-service configuration mode.

number

Numeric code for a named time zone. The following are the selections. The numbers in parentheses indicate the offset from Coordinated Universal Time (UTC) in minutes.

• 1—Dateline Standard Time (-720)
• 2—Samoa Standard Time (-660)
• 3—Hawaiian Standard Time (-600)
• 4—Alaskan Standard/Daylight Time (-540)
• 5—Pacific Standard/Daylight Time (-480)
• 6—Mountain Standard/Daylight Time (-420)
• 7—United States (US) Mountain Standard Time (-420)
• 8—Central Standard/Daylight Time (-360)
• 9—Mexico Standard/Daylight Time (-360)
• 10—Canada Central Standard Time (-360)
• 11—SA Pacific Standard Time (-300)
• 12—Eastern Standard/Daylight Time (-300)
• 13—US Eastern Standard Time (-300)
• 14—Atlantic Standard/Daylight Time (-240)
• 15—South America (SA) Western Standard Time (-240)
• 16—Newfoundland Standard/Daylight Time (-210)
• 17—SA Standard/Daylight Time (-180)
• 18—SA Eastern Standard Time (-180)
• 19—Mid-Atlantic Standard/Daylight Time (-120)
• 20—Azores Standard/Daylight Time (-60)
• 21—UTC Standard/Daylight Time (+0)
• 22—Greenwich Standard Time (+0)
• 23—Western Europe Standard/Daylight Time (+60)
• 24—GTB (Athens, Istanbul, Minsk) Standard/Daylight Time (+60)
• 25—Egypt Standard/Daylight Time (+60)
• 26—Eastern Europe Standard/Daylight Time (+60)

number continued

• 27—Romance Standard/Daylight Time (+120)
• 28—Central Europe Standard/Daylight Time (+120)
• 29—South Africa Standard Time (+120)
• 30—Jerusalem Standard/Daylight Time (+120)
• 31—Saudi Arabia Standard Time (+180)
• 32—Russian Standard/Daylight Time (+180)
• 33—Iran Standard/Daylight Time (+210)
• 34—Caucasus Standard/Daylight Time (+240)
• 35—Arabian Standard Time (+240)
• 36—Afghanistan Standard Time (+270)
• 37—West Asia Standard Time (+300)
• 38—Ekaterinburg Standard Time (+300)
• 39—India Standard Time (+330)
• 40—Central Asia Standard Time (+360)
• 41—Southeast Asia Standard Time (+420)
• 42—China Standard/Daylight Time (+480)
• 43—Taipei Standard Time (+480)
• 44—Tokyo Standard Time (+540)
• 45—Central Australia Standard/Daylight Time (+570)
• 46—Australia Central Standard Time (+570)
• 47—East Australia Standard Time (+600)
• 48—Australia Eastern Standard/Daylight Time (+600)
• 49—West Pacific Standard Time (+600)
• 50—Tasmania Standard/Daylight Time (+600)
• 51—Central Pacific Standard Time (+660)
• 52—Fiji Standard Time (+720)
• 53—New Zealand Standard/Daylight Time (+720)
• 54—Venezuela Standard Time (-270)
• 55—Pacific SA Daylight Time (-180)
• 56—Pacific SA Standard Time (-240)

12.3(11)XL

Cisco CME 3.2.1

This command was introduced.

12.3(14)T

Cisco CME 3.3

This command was integrated into Cisco IOS Release 12.3(14)T.

create cnf-files

Sets display and phone functionality for the Cisco IP Phone 7970 units using the vendorConfig parameters of the downloaded firmware’s Sep*.cnf.xml configuration file.

reset (telephony-service)

Performs a complete reboot of one or all phones associated with a Cisco Unified CME router.

number

Range is 1 to 53. Default is 5, Pacific Standard/Daylight Time

12.4(4)T

Cisco CME 3.4

This command was introduced.

1

Dateline Standard Time

-720

2

Samoa Standard Time

-660

3

Hawaiian Standard Time

-600

4

Alaskan Standard/Daylight Time

-540

5

Pacific Standard/Daylight Time

-480

6

Mountain Standard/Daylight Time

-420

7

US Mountain Standard Time

-420

8

Central Standard/Daylight Time

-360

9

Mexico Standard/Daylight Time

-360

10

Canada Central Standard Time

-360

11

SA Pacific Standard Time

-300

12

Eastern Standard/Daylight Time

-300

13

US Eastern Standard Time

-300

14

Atlantic Standard/Daylight Time

-240

15

SA Western Standard Time

-240

16

Newfoundland Standard/Daylight Time

-210

17

South America Standard/Daylight Time

-180

18

SA Eastern Standard Time

-180

19

Mid-Atlantic Standard/Daylight Time

-120

20

Azores Standard/Daylight Time

-60

21

GMT Standard/Daylight Time

+0

22

Greenwich Standard Time

+0

23

W. Europe Standard/Daylight Time

+60

24

GTB Standard/Daylight Time

+60

25

Egypt Standard/Daylight Time

+60

26

E. Europe Standard/Daylight Time

+60

27

Romance Standard/Daylight Time

+120

28

Central Europe Standard/Daylight Time

+120

29

South Africa Standard Time

+120

30

Jerusalem Standard/Daylight Time

+120

31

Saudi Arabia Standard Time

+180

32

Russian Standard/Daylight Time

+180

33

Iran Standard/Daylight Time

+210

34

Caucasus Standard/Daylight Time

+240

35

Arabian Standard Time

+240

36

Afghanistan Standard Time

+270

37

West Asia Standard Time

+300

38

Ekaterinburg Standard Time

+300

39

India Standard Time

+330

40

Central Asia Standard Time

+360

41

SE Asia Standard Time

+420

42

China Standard/Daylight Time

+480

43

Taipei Standard Time

+480

44

Tokyo Standard Time

+540

45

Cen. Australia Standard/Daylight Time

+570

46

AUS Central Standard Time

+570

47

E. Australia Standard Time

+600

48

AUS Eastern Standard/Daylight Time

+600

49

West Pacific Standard Time

+600

50

Tasmania Standard/Daylight Time

+600

51

Central Pacific Standard Time

+660

52

Fiji Standard Time

+720

53

New Zealand Standard/Daylight Time

+720

54

Venezuela Standard Time

-270

55

Pacific SA Daylight Time

-180

56

Pacific SA Standard Time

-240

dst (voice register global)

Sets the time period for daylight saving time on SIP phones.

dst auto-adjust (voice register global)

Enables automatic adjustment of daylight saving time on SIP phones.

time-format (voice register global)

Selects a 12-hour clock or a 24-hour clock for the time display format on SIP phones in a Cisco CME system

max-length

Maximum length of the transfer number. Range is 3 to 16.

15.3(2)T

This command was introduced.

12.4(4)T

Cisco CME 3.4

This command was introduced.

conference (voice register template)

Enables the soft key for conference in a SIP phone template.

template

Applies a template to a SIP phone.

transfer-blind (voice register template)

Enables a soft key for blind transfer in a SIP phone template.

12.4(4)T

Cisco CME 3.4

This command was introduced.

conference (voice register template)

Enables the soft key for conference in a SIP phone template.

template

Applies a template to a SIP phone.

transfer-attended (voice register template)

Enables the soft key for attended transfer on SIP phones.

new-call

Dialed digits are collected from new call leg. Default value.

orig-call

Dialed digits are collected from original call leg.

12.4(15)XZ

Cisco Unified CME 4.3 Cisco Unified SRST 4.3

This command was introduced.

12.4(20)T

Cisco Unified CME 7.0 Cisco Unified SRST 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

transfer-mode

Specifies the type of call transfer for an individual directory number that uses the ITU-T H.450.2 standard.

transfer-pattern (telephony-service)

Allows the transfer of calls to phones outside the local Cisco Unified CME network.

transfer-system

Specifies the call transfer method for all IP phones on a Cisco Unified CME router using the ITU-T H.450.2 standard.

blind

Transfers calls without consultation using a single phone line.

consult

Transfers calls with consultation using a second phone line, if available.

12.2(11)YT

2.1

This command was introduced.

12.2(15)T

2.1

This command was integrated into Cisco IOS Release 12.2(15)T.

ephone-dn

Enters ephone-dn configuration mode to set directory numbers and parameters for individual Cisco IP phone lines.

transfer-system

Specifies the call transfer method for all IP phones on a Cisco ITS router using the ITU-T H.450.2 standard.

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

transfer-pattern

String of digits for permitted call transfers. Wildcards are allowed. A maximum of 32 transfer patterns can be entered, using a separate command for each one.

blind

(Optional) When H.450.2 consultative call transfer is used, this keyword forces transfers that match the pattern to be executed as blind transfers. Overrides settings made using the transfer-system and transfer-mode commands.

12.1(5)YD

Cisco ITS 1.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

12.2(15)T

Cisco ITS 2.1

The blind keyword was added.

transfer-mode

Specifies the type of call transfer for an individual IP phone extension number that uses the ITU-T H.450.2 standard.

transfer-system

Specifies the call transfer method for all Cisco CME extensions that use the ITU-T H.450.2 standard.

15.3(2)T

This command was introduced.

voice register pool

Enters voice register pool configuration mode and creates a pool configuration for a Cisco Unified SIP IP phone in Cisco Unified CME or for a set of Cisco Unified SIP IP phones in Cisco Unified SIP SRST.

voice register template

Enters voice register template configuration mode and defines a template of common parameters for Cisco Unified SIP IP phones.

blind

Transfers calls without consultation using a single phone line and the Cisco proprietary method. This is the default for Cisco CME 3.4 and earlier versions.

full-blind

Transfers calls without consultation using H.450.2 standard methods.

full-consult

Transfers calls using H.450.2 with consultation using a second phone line, if available. The calls fall back to full-blind if a second line is not available. This is the default for Cisco Unified CME 4.0 and later versions.

dss

Transfers calls with consultation to idle monitor lines. All other call-transfer behavior is identical to full-consult.

local-consult

Transfers calls with local consultation using a second phone line, if available, or the calls fall back to blind if the target for consultation or transfer is not local. This mode is intended for use primarily in Voice over Frame Relay (VoFR) networks, because the Cisco VoFR call transfer protocol does not support an end-to-end transfer-with-consultation mechanism. Not supported if transfer-to destination is on the Cisco ATA, Cisco VG224, or a SCCP-controlled FXS port.

12.2(11)YT

Cisco ITS 2.1

This command was introduced.

12.2(15)T

Cisco ITS 2.1

This command was integrated into Cisco IOS Release 12.2(15)T.

12.3(11)T

Cisco CME 3.2

The dss keyword was introduced.

12.4(4)XC

Cisco Unified CME 4.0

The command default was changed from blind to full-consult.

12.4(9)T

Cisco Unified CME 4.0

This command with the default of full-consult was integrated into Cisco IOS Release 12.4(9)T.

Cisco Unified CME 4.0 and later versions

full-consult

full-consult orfull-blind

Use H.450.2 for call transfer. Because this is the default for this version, you do not need to use the transfer-system command unless you want to use the full-blind or dss keyword.

Optionally, you can use the proprietary Cisco method by using the transfer-system command with the blind or local-consult keyword.

Cisco CME 3.0 to 3.3

blind

full-consult orfull-blind

Use H.450.2 for call transfer. You must explicitly configure the transfer-system command with the full-consult or full-blind keyword because H.450.2 is not the default for this version.

Optionally, you can use the proprietary Cisco method by using the transfer-system command with the blind or local-consult keyword.

Cisco ITS 2.1 to 3.0

blind

blind orlocal-consult

Use the Cisco proprietary method. Because this is the default for this version, you do not need to use the transfer-system command unless you want to use the local-consult keyword.

Optionally, you can use the H.450.2 standard for call transfer by using transfer-system command with the full-consult or full-blind keyword. You must also configure the router with a Tcl script that is contained in the file called app-h450-transfer.x.x.x.x.zip. This file is posted on the Cisco Unified CME software download website at http:/​/​www.cisco.com/​cgi-bin/​tablebuild.pl/​ip-iostsp .

transfer-mode

Specifies the type of call transfer for an individual IP phone extension that uses the H.450.2 standard.

called

Translate the called number.

calling

Translate the calling number.

translation-rule-tag

Unique sequence number by which the rule set is referenced. This number is arbitrarily chosen. Range is from 1 to 2147483647. There is no default value.

12.2(2)XT

Cisco ITS 2.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

12.4(4)XC

Cisco Unified CME 4.0

This command was made available in ephone-dn-template configuration mode.

12.4(9)T

Cisco Unified CME 4.0

This command in ephone-dn-template configuration mode was integrated into Cisco IOS Release 12.4(9)T.

rule

Defines a translation rule.

translation-rule

Creates a translation identifier and enters translation-rule configuration mode.

incoming

Specifies that this translation profile handles incoming calls.

outgoing

Specifies that this translation profile handles outgoing calls.

name

Name of the translation profile.

15.1(3)T

Cisco Unified CME 8.5

This command was introduced.

show voice translation-profile

Displays the configuration of a translation profile.

translate (call-manager- fallback)

Applies a translation rule to modify the phone number dialed or received by any Cisco IP phone user during CallManager fallback.

translation-rule

Creates a translation name and enters translation-rule configuration mode to apply rules to the translation name.

voice translation-profile

Defines a translation profile for voice calls.

called

Called party requires translation.

calling

Calling party requires translation.

rule-tag

The rule-tag is an arbitrarily chosen number by which the rule set is

referenced. The range is from 1 to 2147483.

12.2(15)ZJ

Cisco SIP SRST 3.0

This command was introduced.

12.3(4)T

Cisco SIP SRST 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

12.4(4)T

Cisco CME 3.4 Cisco SIP SRST 3.4

This command was added to Cisco CME.

alias (voice register pool)

Allows Cisco SIP IP phones to handle inbound PSTN calls to telephone numbers that are unavailable when the main proxy is not available.

id (voice register pool)

Explicitly identifies a locally available individual Cisco SIP IP phone, or when running Cisco Unified SIP SRST, set of Cisco SIP IP phones.

translate-outgoing (dial-peer)

Applies a translation rule to manipulate dialed digits on an outbound POTS or VoIP call leg.

voice register pool

Enters voice register pool configuration mode for SIP phones.

incoming

Specifies that this translation profile handles incoming calls.

outgoing

Specifies that this translation profile handles outgoing calls.

name

Name of the translation profile.

12.3(11)T

Cisco CME 3.2

This command was introduced.

12.4(4)XC

Cisco Unified CME 4.0

This command was made available in ephone-dn-template configuration mode.

12.4(9)T

Cisco Unified CME 4.0

This command in ephone-dn-template configuration mode was integrated into Cisco IOS Release 12.4(9)T.

show voice translation-profile

Displays the configuration of a translation profile.

translate

Applies a translation rule to modify the phone number dialed or received by any Cisco Unified IP phone user.

translation-rule

Creates a translation name and enters translation-rule configuration mode.

voice translation-profile

Defines a translation profile for voice calls.

voice translation-rule

Defines a translation rule for voice calls.

name

Name of the translation profile to apply to incoming calls to this directory number. This is the name argument that was created for the profile with the voice translation-profile command.

12.4(11)XJ

Cisco Unified CME 4.1

This command was introduced.

12.4(15)T

Cisco Unified CME 4.1

This command was integrated into Cisco IOS Release 12.4(15)T.

show voice translation-profile

Displays the configuration of a translation profile.

translate (translation profiles)

Associates a translation rule with a voice translation profile.

voice translation-profile

Defines a translation profile for voice calls.

voice translation-rule

Defines a translation rule for voice calls.

Adds a new Cisco Unified SIP IP phone to Cisco Unified CME.

digit-string

The number of the trunk line.

timeout seconds

(Optional) Interdigit timeout between dialed digits, in seconds. Range is 3 to 30. Default is 3.

transfer-timeout seconds

(Optional) Number of seconds that Cisco Unified CME waits for the transfer-to party to answer a call after which the call is recalled to the phone that initiated the transfer. This keyword is supported for dual-line ephone-dns only. Range is 5 to 60000. Default is disabled.

monitor-port port

(Optional) Enables a button lamp or icon that shows that the specified port is in use. Port argument is platform-dependent; type ? to display syntax.

12.3(11)T

Cisco CME 3.2

This command was introduced.

12.4(4)XC

Cisco Unified CME 4.0

The monitor-port and transfer-timeout keywords were added and support for dual-line ephone-dns was added.

12.4(9)T

Cisco Unified CME 4.0

This command with modifications was integrated into Cisco IOS Release 12.4(9)T.

destination-number

Specifies a connection mode for a voice port.

trustpoint-name

Name of the trustpoint to be associated with the Cisco Unified CME CTL provider certificate or the Cisco Unified SRST device certificate.

12.3(14)T

Cisco SRST 3.3

This command was introduced for Cisco SRST.

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced for Cisco Unified CME.

12.4(9)T

Cisco Unified CME 4.0

This command for Cisco Unified CME was integrated into Cisco IOS Release 12.4(9)T.

ctl-service admin

Specifies a user name and password to authenticate the CTL client during the CTL protocol.

debug credentials

Sets debugging on the credentials service.

ip source-address (credentials)

Enables the router to receive messages through the specified IP address and port.

show credentials

Displays the credentials settings.

label

Trustpoint name for the CAPF server.

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

phone-type

Type of phone. The following phone types are predefined in the system:

• 12SP—12SP+ and 30VIP phones.
• 6901—Cisco Unified IP Phone 6901.
• 6911—Cisco Unified IP Phone 6911.
• 6921— Cisco Unified IP Phone 6921.
• 6941—Cisco Unified IP Phone 6941.
• 6945—Cisco Unified IP Phone 6945.
• 6961—Cisco Unified IP Phone 6961.
• 7902—Cisco Unified IP Phone 7902G.
• 7905—Cisco Unified IP Phone 7905G.
• 7906—Cisco Unified IP Phone 7906.
• 7910—Cisco Unified IP Phones 7910 and 7910G.
• 7911—Cisco Unified IP Phone 7911G.
• 7912—Cisco Unified IP Phone 7912G.
• 7920—Cisco Unified IP Phone 7920.
• 7921—Cisco Unified Wireless IP Phone 7921.
• 7925—Cisco Unified Wireless IP Phone 7925.
• 7931—Cisco Unified IP Phone 7931G.
• 7935—Cisco Unified IP Conference Station 7935.
• 7936—Cisco Unified IP Conference Station 7936.
• 7937—Cisco Unified IP Conference Station 7937.
• 7940—Cisco Unified IP Phone 7940G.
• 7941—Cisco Unified IP Phone 7941G.
• 7941GE—Cisco Unified IP Phone 7941G-GE.

• 7942—Cisco Unified IP Phone 7942.
• 7945—Cisco Unified IP Phone 7945
• 7960—Cisco Unified IP Phone 7960G.
• 7961—Cisco Unified IP Phone 7961G.
• 7961GE—Cisco Unified IP Phone 7961G-GE.
• 7962—Cisco Unified IP Phone 7962.
• 7965—Cisco Unified IP Phone 7965.
• 7970—Cisco Unified IP Phone 7970G.
• 7971—Cisco Unified IP Phone 7971G-GE.
• 7975—Cisco Unified IP Phone 7975.
• 7985—Cisco Unified IP Phone 7985.
• 8941—Cisco Unified IP Phone 8941.
• 8945—Cisco Unified IP Phone 8945.
• 8961—Cisco Unified IP Phone 8961.
• 9951—Cisco Unified IP Phone 9951.
• 9971—Cisco Unified IP Phone 9971.
• anl—Analog.
• ata—Cisco ATA-186 or Cisco ATA-188.
• bri —SCCP Gateway (BR).
• vgc-phone —VG248 phone emulation for analog phone.

addon 1 module-type

(Optional) Tells the router that an expansion module is being added to this Cisco Unified IP Phone and the type of module. Valid entries for module-type are:

• 7914—Cisco Unified IP Phone 7914 Expansion Module.
• 7915-12—Cisco Unified IP Phone 7915 12-Button Expansion Module.
• 7915-24—Cisco Unified IP Phone 7915 24-Button Expansion Module.
• 7916-12—Cisco Unified IP Phone 7916 12-Button Expansion Module.
• 7916-24—Cisco Unified IP Phone 7916 24-Button Expansion Module.

2 module-type

(Optional) Tells the router that a second expansion module is being added to this Cisco Unified IP Phone and the type of module. Valid entries for module-type are:

• 7914—Cisco Unified IP Phone 7914 Expansion Module.
• 7915-12—Cisco Unified IP Phone 7915 12-Button Expansion Module.
• 7915-24—Cisco Unified IP Phone 7915 24-Button Expansion Module.
• 7916-12—Cisco Unified IP Phone 7916 12-Button Expansion Module.
• 7916-24—Cisco Unified IP Phone 7916 24-Button Expansion Module.

12.2(11)YT

Cisco ITS 2.1

This command was introduced.

12.2(15)T

Cisco ITS 2.1

This command was integrated into Cisco IOS Release 12.2(15)T.

12.2(15)ZJ

Cisco CME 3.0

The following keywords were added to this command: 7902, 7905, and 7912.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

12.3(7)T

Cisco CME 3.1

The 7920 and 7936 keywords were added.

12.3(11)XL

Cisco CME 3.2(1)

The 7970 keyword was added.

12.3(14)T

Cisco CME 3.3

The 7971 keyword was added, and this command was integrated into Cisco IOS Release 12.3(14)T.

12.4(4)XC

Cisco Unified CME 4.0

The 7911, 7941, 7941GE, 7961, and 7961GE keywords were added. This command was made available in ephone-template configuration mode.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

12.4(6)XE

Cisco Unified CME 4.0(2)

The 7931 keyword was added.

12.4(4)XC4

Cisco Unified CME 4.0(3)

The 7931 keyword was added.

12.4(11)T

Cisco Unified CME 4.0(3)

This command was integrated into Cisco IOS Release 12.4(11)T.

12.4(11)XJ2

Cisco Unified CME 4.1

The 7921 and 7985 keywords were introduced.

12.4(15)T

Cisco Unified CME 4.1

This command was integrated into Cisco IOS Release 12.4(15)T.

12.4(15)T1

Cisco Unified CME 4.1(1)

The 7942, 7945, 7962, 7965, and 7975 keywords were introduced.

12.4(15)XZ

Cisco Unified CME 4.3

Support for user-defined phone types created with the ephone-type command was added.

12.4(15)XZ1

Cisco Unified CME 4.3

The 7915-12, 7915-24, 7916-12, 7916-24, and 7937 keywords were added.

12.4(20)T

Cisco Unified CME 7.0

The 7915-12, 7915-24, 7916-12, 7916-24, and 7937 keywords were added and this command was integrated into Cisco IOS Release 12.4(20)T.

12.4(20)T1

Cisco Unified CME 7.0

The 7925 keyword was added.

15.0(1)XA

Cisco Unified CME 8.0

This command was modified. The 6921, 6941, 6961, and IP-STE keywords were added.

15.1(1)T

Cisco Unified CME 8.0

This command was integrated into Cisco IOS Release 15.1(1)T.

15.1(2)T

Cisco Unified CME 8.1

This command was modified. The 6901 and 6911 keywords were added.

15.2(1)T

Cisco Unified CME 8.8

This command was modified. The 6945, 8941, and 8945 keywords were added.

15.3(3)M

Cisco Unified CME 10.0

This command was modified. The 7906, 8961, 9951, and 9971 keywords were added.

ephone-type

Adds a Cisco Unified IP phone type by defining a phone-type template.

reset (ephone)

Performs a complete reboot of one phone associated with a Cisco Unified CME router.

reset (telephony-service)

Performs a complete reboot of one or all phones associated with a Cisco Unified CME router.

phone-type

Type of SIP phone for which the dial plan is used. Values are:

• 7905-7912—Cisco Unified IP Phone 7905, 7905G, 7912, or 7912G.
• 7940-7960-others—Cisco Unified IP Phone 7911, 7940, 7940G, 7941, 7942, 7941GE, 7945, 7960, 7960G, 7961, 7961GE, 7962, 7965, 7970, 7971, or 7975.

12.4(11)XJ

Cisco Unified CME 4.1

This command was introduced.

12.4(15)T

Cisco Unified CME 4.1

This command was integrated into Cisco IOS Release 12.4(15)T.

12.4(15)XZ

Cisco Unified CME 4.3

Support for Cisco Unified IP Phone 7942, 7945, 7962, 7965, and 7975 was added.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

dialplan

Assigns a dial plan to a SIP phone.

filename

Specifies a custom XML file that contains the dial patterns to use for the SIP dial plan.

pattern (voice register dialplan)

Defines a dial pattern for a SIP dial plan.

show voice register dialplan

Displays configuration information for a specific SIP dial plan.

type (voice register pool)

Defines a phone type for a SIP phone.

phone-type

Type of SIP phone that is being defined. Valid entries are as follows:

• 3905—Cisco Unified IP Phone 3905.
• 3951—Cisco Unified IP Phones 3911 and 3951.
• 6901—Cisco Unified IP Phone 6901.
• 6911—Cisco Unified IP Phone 6911.
• 6921—Cisco Unified IP Phone 6921.
• 6922—Cisco Unified IP Phone 6922.
• 6941—Cisco Unified IP Phone 6941.
• 6945—Cisco Unified IP Phone 6945.
• 6961—Cisco Unified IP Phone 6961.
• 7821—Cisco Unified IP Phones 7821.
• 7841—Cisco Unified IP Phones 7841.
• 7861—Cisco Unified IP Phones 7861.
• 7905—Cisco Unified IP Phones 7905 and 7905G.
• 7906—Cisco Unified IP Phone 7906G.
• 7911—Cisco Unified IP Phone 7911G.
• 7912—Cisco IP Phones 7912 and 7912G.
• 7940—Cisco IP Phones 7940 and 7940G.
• 7941—Cisco IP Phone 7941G.
• 7941GE—Cisco IP Phone 7941GE.
• 7942—Cisco Unified IP Phone 7942.
• 7945—Cisco Unified IP Phone 7945.
• 7960—Cisco IP Phones 7960 and 7960G.
• 7961—Cisco IP Phone 7961G.
• 7961GE—Cisco IP Phone 7961GE.
• 7962—Cisco Unified IP Phone 7962.
• 7965—Cisco Unified IP Phone 7965.
• 7970—Cisco IP Phone 7970G.
• 7971—Cisco IP Phone 7971GE.
• 7975—Cisco Unified IP Phone 7975.
• 8961—Cisco Unified IP Phone 8961.
• 9900—Cisco Unified IP Phone 9900.
• 9951—Cisco Unified IP Phone 9951.
• 9971—Cisco Unified IP Phone 9971.
• ATA—Cisco ATA-186 or Cisco ATA-188.
• ATA-187—Cisco ATA-187.
• DX650—Cisco DX650.
• Jabber-Android—Cisco Jabber App on Android.
• P100—PingTel Xpressa 100.
• P600—Polycom SoundPoint 600.
• Jabber-CSF-Client—Cisco Jabber CSF Client.

addon 1 CKEM

(Optional) Tells the router that a Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

2 CKEM

(Optional) Tells the router that a second Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

3 CKEM

(Optional) Tells the router that a third Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

12.4(4)T

Cisco CME 3.4

This command was introduced.

12.4(11)XJ

Cisco Unified CME 4.1

This command was modified to add the 3951, 7911, 7941, 7941GE, 7961, 7961GE, 7970, and 7971 keywords.

12.4(15)T

Cisco Unified CME 4.1

The 3951, 7911, 7941, 7941GE, 7961, 7961GE, 7970, and 7971 keywords were integrated into Cisco IOS Release 12.4(15)T.

12.4(15)XZ

Cisco Unified CME 4.3

This command was modified to add the 7942, 7945, 7962, 7965, and 7975 keywords.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

15.1(3)T

Cisco Unified CME8.5

This command was modified to add the 8961, 9951,and 9971 keywords.

15.2(1)T

Cisco Unified CME 8.8

This command was modified to add the 3905 keyword.

15.2(2)T

Cisco Unified CME 9.0

This command was modified to add the 6901, 6911, 6921, 6941, 6945, 6961, ATA-187, and Jabber-Android keywords.

15.2(4)M

Cisco Unified CME 9.1

This command was modified to include the addon 1 CKEM, 2 CKEM, and 3 CKEM keywords.

15.3(3)M

Cisco Unified CME 10.0

This command was modified to add the 6922 and 9900 keywords.

15.4(3)M

Cisco Unified CME 10.5

This command was modified. The 78XX, DX650 and Jabber-CSF-Clientkeywords were added.

busy-trigger-per-button (voice register pool)

Sets the maximum number of calls allowed on a SIP directory number before activating Call Forward Busy or a busy tone.

load (voice register global)

Associates a type of Cisco Unified SIP IP phone with a phone firmware file.

reset (voice register global)

Performs a complete reboot of all SIP phones associated with a Cisco Unified CME router.

reset (voice register pool)

Performs a complete reboot of one SIP phone associated with a Cisco Unified CME router.

restart (voice register)

Performs a fast reset of one or all SIP phones associated with a Cisco Unified CME router.

voice register pool

Enters voice register pool configuration mode for SIP phones.

vg202

Cisco VG202 Voice Gateway with 2 FXS ports.

vg204

Cisco VG204 Voice Gateway with 4 FXS ports.

vg224

Cisco VG224 Voice Gateway with 24 FXS ports.

12.4(22)YB

Cisco Unified CME 7.1

This command was introduced.

12.4(24)T

Cisco Unified CME 7.1

This command was integrated into Cisco IOS Release 12.4(24)T.

create cnf-files (voice-gateway)

Generates the XML configuration files that are required to autoconfigure the Cisco voice gateway.

mac-address (voice-gateway)

Defines the MAC address of the voice gateway to autoconfigure.

voice-port (voice-gateway)

Identifies the ports on the voice gateway that register to Cisco Unified CME.