Table Of Contents
Checking Basic Configuration Settings
Resetting the Access Point/Bridge to the Default Configuration
Using the Web-Browser Interface
Corrupt IOS Configuration or Lost Password Procedure
Reloading the Access Point/Bridge Image
Obtaining the Access Point/Bridge Image File
Obtaining the TFTP Server Software
Troubleshooting
This chapter provides troubleshooting procedures for basic problems with the access point/bridge. For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at the following URL (select Hardware Support > Wireless Devices):
http://www.cisco.com/cisco/web/support/index.html
Sections in this chapter include:
•Checking Basic Configuration Settings
•Resetting the Access Point/Bridge to the Default Configuration
•Reloading the Access Point/Bridge Image
Checking the LEDs
If your access point/bridge is not associating with a remote bridge or access point, check the four LEDs on the back panel. You can use them to quickly assess the unit's status. For information on using the LEDs during the installation and alignment of the access point/bridge antenna, refer to the Cisco Aironet 1300 Series Outdoor Access Point/Bridge Mounting Instructions that shipped with your access point/bridge.
Figure 21-1 shows the access point/bridge LEDs.
Figure 21-1 LEDs
Normal Mode LED Indications
During access point/bridge operation the LEDs provide status information as shown in Table 21-1.
Table 21-1 LED Indications
Ethernet
LED Status
LED Radio
LED Install
LED Meaning
Off
—
—
—
Ethernet link is down or disabled.
Blinking green
—
—
—
Transmitting and receiving Ethernet packets.
Blinking amber
—
—
—
Transmitting and receiving Ethernet errors.
amber
—
—
—
Firmware error—disconnect and reconnect the power injector power jack. If the problem continues, contact technical support for assistance.
—
Blinking green
—
—
Root bridge mode—no remote bridges are associated.
Non-root bridge mode—not associated to the root bridge.
If all bridges are powered up, this could be caused by incorrect SSID and security settings or improper antenna alignment. You should check the SSID and security settings of all bridges and verify antenna alignment.If the problem continues, contact technical support for assistance.
—
Green
—
—
Root mode—associated to at least one remote bridge.
Non-root mode—associated to the root bridge.
This is normal operation.—
Blinking amber
—
—
General warning—disconnect and reconnect the power injector power jack. If the problem continues, contact technical support for assistance.
—
Amber
—
—
Loading firmware.
Red
Amber
Red
—
Loading Firmware error—disconnect and reconnect the power injector power. If the problem continues, contact technical support for assistance.
—
—
Off
—
Normal operation.
—
—
Blinking green
—
Transmitting and receiving radio packets—normal operation.
—
—
Blinking amber
—
Maximum retries or buffer full occurred on the radio interface—disconnect and reconnect the power injector power jack. If the problem continues, contact technical support for assistance.
—
—
Amber
—
Radio firmware error—disconnect and reconnect power injector power.If the problem continues, contact technical support for assistance.
—
—
—
Amber blinking
Not associated (non-root mode). The access point/bridge attempts to associate with a root bridge for 60 seconds1 .
—
—
—
Amber
Associated (non-root mode).
—
—
—
Green blinking
Not associated (root mode). The access point/bridge attempts to associate with a non-root bridge indefinitely.
—
—
—
Green
Associated (root mode).
—
—
—
Red
Overcurrent or overvoltage error—disconnect power to the power injector, check all coax cable connections, wait approximately 1 minute, and reconnect power. If error continues, contact technical support.
1 Preconfigured bridges search indefinitely.
The access point/bridge uses a blinking code to identify various error conditions. The code sequence uses a two-digit diagnostic code that starts with a long pause to delimit the code, followed by the LED flashing red to count out the first digit, then a short pause, followed by the LED flashing red to count out the second digit.
The LED blinking error codes are described in Table 21-2.
Power Injector
When the power injector is powered up, it applies 48-VDC to the dual-coax cables to the access point/bridge.
When power is applied to the access point/bridge, the unit activates the bootloader and begins the POST operations. The access point/bridge begins to load the IOS image when the Post operations are successfully completed. Upon successfully loading the IOS image, the unit initializes and tests the radio.
The power injector LED is shown in Figure 21-2.
Figure 21-2 Power Injector
1Dual-coax Ethernet ports (F-Type connectors)
4Ethernet LAN port (RJ-45 connector)
2Power LED
5Console serial port (RJ-45 connector)
3Power jack
The power injector is available in two models:
•Cisco Aironet Power Injector LR2—standard version (included with the bridge)
–48-VDC input power
–Uses the 48-VDC power module (included with the bridge)
•Cisco Aironet Power Injector LR2T—optional transportation version
–12- to 40-VDC input power
–Uses 12 to 40 VDC from a vehicle battery
Checking Power
You can verify the availability of power to the access point/bridge by checking the power injector LED (see Figure 21-2):
•Power LED
–Green color indicates input power is being supplied to the bridge.
–Red color indicates an overcurrent or overvoltage error condition—disconnect input power from the power injector, check all coax cable connections for a possible short, wait approximately 1 minute, and reconnect input power to the power injector. If the LED turns red again, contact technical support for assistance.
Note The power injector requires approximately 50 seconds to recover from an overcurrent or overvoltage condition.
–Off indicates input power is not available—verify that the power module is connected to the power injector and that AC power is available or that 12- to 40-VDC input power is connected to the power injector.
Checking Basic Configuration Settings
Mismatched basic settings are the most common causes of lost wireless connectivity. If the access point/bridge does not associate with a remote bridge, access point, or client device, check the following areas.
SSID
To associate, all bridges, access points, workgroup bridges, or client devices must use the same SSID. The bridge installation mode SSID is autoinstall and the normal mode default SSID is tsunami. You should verify that the SSID value shown on the Express Setup page is the same for all bridges, access points, workgroup bridges, or client devices. You should also verify that the bridges or access points are configured for the proper network role; only one bridge can be configured as the root bridge and only one access point can be configured as a root access point.
Note Access points and bridges are not designed to associate together. However, a workgroup bridge can associate to either a Cisco Aironet access point or a Cisco Aironet bridge.
Security Settings
Remote Cisco Aironet bridges or client devices attempting to authenticate to your access point/bridge must support the same security options configured in the access point/bridge, such as WEP, EAP or LEAP, MAC address authentication, Message Integrity Check (MIC), WEP key hashing, and 802.1X protocol versions.
If a Cisco Aironet non-root bridge or a non-root access point is unable to authenticate to your root bridge or root access point, verify that the security settings are the same as your access point/bridge settings. For additional information, refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points.
Antenna Alignment
If your non-root bridges or non-root access points are unable to associate to your root bridge or root access point, you should verify the basic configuration settings on all bridges or access points before attempting to verify antenna alignment (Chapter 2, "Configuring the Access Point/Bridge for the First Time." If your basic configuration settings are correct, you can verify antenna alignment by using the Install mode RSSI LED indications. For additional information, refer to the Cisco Aironet 1300 Series Outdoor Access Point/Bridge Mounting Instructions that shipped with your access point/bridge.
Note To meet regulatory restrictions, the external antenna access point/bridge unit and the external antenna must be professionally installed. The network administration or other IT professional responsible for installing and configuring the unit is a suitable professional installer. Following installation, access to the unit should be password protected by the network administrator to maintain regulatory compliance.
Resetting the Access Point/Bridge to the Default Configuration
You can use the web-browser interface or the CLI to reset the access point/bridge to a factory default configuration.
Note The following steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID. The default username and password are both Cisco, which is case-sensitive.
Using the Web-Browser Interface
Follow the steps below to delete the current configuration and return all access point/bridge settings to the factory defaults using the Web-browser interface.
Step 1 Open your Internet browser.
Step 2 Enter the bridge's IP address in the browser address or location line and press Enter. An Enter Network Password screen appears.
Step 3 Enter your username (default Cisco) in the User Name field.
Step 4 Enter the access point/bridge password (default Cisco) in the Password field and press Enter. The Summary Status page appears.
Step 5 Click System Software and the System Software screen appears.
Step 6 Click System Configuration and the System Configuration screen appears.
Step 7 Click Default.
Note If the access point/bridge is configured with a static IP address, the IP address does not change.
Step 8 After the access point/bridge reboots, you can reconfigure the access point/bridge by using the Web-browser interface or the CLI (refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points).
Using the CLI
From the privileged EXEC mode, you can reset the access point/bridge configuration to factory default values using the CLI by following these steps:
Step 1 Enter erase nvram: to erase all NVRAM files including the startup configuration.
Step 2 Enter Y when the following CLI message displays: Erasing the nvram filesystem will remove all configuration files! Continue? [confirm].
Step 3 Enter reload when the following CLI message displays: Erase of nvram: complete. This command reloads the operating system.
Step 4 Enter Y when the following CLI message displays: Proceed with reload? [confirm].
Caution Do not interrupt the boot process to avoid damaging the configuration file. Wait until the access point/bridge Install Mode LED begins to blink green before continuing with CLI configuration changes. You can also see the following CLI message when the load process has finished: Line protocol on Interface Dot11Radio0, changed state to up.
Step 5 After the access point/bridge reboots, you can reconfigure the access point/bridge by using the Web-browser interface or the CLI (refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points).
The access point/bridge is configured with the factory default values including the IP address (set to receive an IP address using DHCP). To obtain the unit's new IP address, you can use the show interface bvi1 CLI command. If the unit does not receive an IP address from a DHCP server, the access point/bridge IP address is 10.0.0.1.
Corrupt IOS Configuration or Lost Password Procedure
This section describes the procedure for resetting the access point/bridge to its default settings in the unlikely event that the operating system is corrupt or if you have misplaced the configuration login and password. Because the access point/bridge does not have a mode switch, you must use the console port to perform this operation. Follow these steps to reset the unit to its default settings:
Step 1 Open the CLI using a Telnet session or a connection to the access point/bridge's console port.
Step 2 Reboot the access point/bridge by removing power and reapplying power.
Step 3 Let the access point/bridge boot until the command prompt appears and the access point/bridge begins to inflate the image. When you see these lines on the CLI, press Esc:
Note Depending on the terminal emulation software you are using, you may have to press Esc twice to access the boot loader.
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"...####################################################################################################################################################################################################################################################Messages similar to those below appear:
Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"Interrupt within 5 seconds to abort boot process.Boot process terminated.The system is unable to boot automatically. The BOOT environment variable needs to be set to a bootable image.C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]bridge:Step 4 At the prompt, enter the following command to show a directory of the flash file system similar to the directory shown below:
bridge: dir flash:Directory of flash:/2 -rwx 0 <date> env_vars5 drwx 384 <date> C1310-k9w7-mx.v133_15_JA.200403143 -rwx 1128 <date> config.txt4 -rwx 5 <date> private-config3693568 bytes available (4047872 bytes used)bridge:Step 5 Delete or rename the files config.txt and env_vars and reboot the bridge. Don't forget the / character before the filenames:
bridge: delete flash:config.txtAre you sure you want to delete flash:/config.txt (y/n)?yFile "flash:/config.txt" deletedbridge: delete flash:/env_varsAre you sure you want to delete "flash:/env_vars" (y/n)?yFile "flash:/env_vars" deletedbridge: boot
Note The access point/bridge is configured with factory default values, including the IP address (set to receive an IP address using DHCP) and the default case-sensitive user name and password (Cisco).
Step 6 When IOS software is loaded and you chose to rename the env_vars and config.txt files, you can use the del privileged EXEC command to delete them from Flash.
bridge# del flash:env_varsoldDelete filename [env_varsold]Delete flash:env_varsold [confirm]br#bridge# del flash:config.oldDelete filename [config.old]Delete flash:config.old [confirm]bridge#
Reloading the Access Point/Bridge Image
If your access point/bridge has a firmware failure, you must reload the complete image file using the Web-browser interface or by using the console serial port. You can use the browser interface if the access point/bridge firmware is operational. However, you can use the console serial port when the access point/bridge has a corrupt image.
Web-Browser Interface
You can also use the Web-browser interface to reload the access point/bridge image file. The Web-browser interface supports loading the image file using HTTP or TFTP interfaces.
Note Your access point/bridge configuration is not changed when using the browser to reload the image file.
Browser HTTP Interface
The HTTP interface enables you to browse to the access point/bridge image file on your PC and download the image to the unit. Follow the instructions below to use the HTTP interface:
Step 1 Open your Internet browser.
Step 2 Enter the access point/bridge's IP address in the browser address or location line and press Enter. An Enter Network Password screen appears.
Step 3 Enter your username in the User Name field.
Step 4 Enter the access point/bridge password in the Password field and press Enter. The Summary Status page appears.
Step 5 Click the System Software tab and then click Software Upgrade. The HTTP Upgrade screen appears.
Step 6 Click Browse to locate the image file on your PC.
Step 7 Click Upload.
Step 8 After the access point/bridge reboots, you can reconfigure the unit by using the Web-browser interface or the CLI (refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points).
For additional information, click the Help icon on the Software Upgrade screen.
Browser TFTP Interface
The TFTP interface enables you to use a TFTP server on a network device to load the access point/bridge image file. Follow the instructions below to use a TFTP server:
Step 1 Open your Internet browser.
Step 2 Enter the access point/bridge's IP address in the browser address or location line and press Enter. An Enter Network Password screen appears.
Step 3 Enter your username in the User Name field.
Step 4 Enter the access point/bridge password in the Password field and press Enter. The Summary Status page appears.
Step 5 Click System Software and then click Software Upgrade. The HTTP Upgrade screen appears.
Step 6 Click TFTP Upgrade.
Step 7 Enter the IP address for the TFTP server in the TFTP Server field.
Step 8 Enter the filename for the access point/bridge image file (c1310-k9w7-tar.122-15.JA.tar) in the Upload New System Image Tar File field. If the file is located in a subdirectory of the TFTP server root directory, include the relative path of the TFTP server root directory with the filename. If the file is in the TFTP root directory, enter only the filename.
Step 9 Click Upload.
Step 10 After the access point/bridge reboots, you can reconfigure the access point/bridge by using the Web-browser interface or the CLI (refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Bridges or to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points).
For additional information click the Help icon on the Software Upgrade screen.
Using the CLI
Follow the steps below to reload the access point image using the CLI. When the access point begins to boot, you interrupt the boot process and use boot loader commands to load an image from a TFTP server to replace the image in the access point.
Note Your access point configuration is not changed when using the CLI to reload the image file.
Step 1 Open the CLI using a Telnet session or a connection to the access point console port.
Step 2 Reboot the access point by removing power and reapplying power.
Step 3 Let the access point boot until it begins to inflate the image. When you see these lines on the CLI, press Esc:
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"...########################################################################### ################################################################################ ################################################################################ ####################
Note Depending on the terminal emulation software you are using, you may have to press Esc twice to access the boot loader.
Step 4 When the bridge: command prompt appears, enter the set command to assign an IP address, subnet mask, and default gateway to the access point.
Note You must use upper-case characters when you enter the IP-ADDR, NETMASK, and DEFAULT_ROUTER options with the set command.
Your entries might look like this example:
bridge: set IP_ADDR 192.168.133.160
bridge: set NETMASK 255.255.255.0
bridge: set DEFAULT_ROUTER 192.168.133.1
Step 5 Enter the tftp_init command to prepare the access point for TFTP.
bridge: tftp_init
Step 6 Enter the tar command to load and inflate the new image from your TFTP server. The command must include this information:
•the -xtract option, which inflates the image when it is loaded
•the IP address of your TFTP server
•the directory on the TFTP server that contains the image
•the name of the image
•the destination for the image (the access point Flash)
Your entry might look like this example:
bridge: tar -xtract tftp://192.168.130.222/images/c1310-k9w7-tar.122_15.JA1 flash:Step 7 When the display becomes full the CLI pauses and displays
--MORE--
. Press the spacebar to continue.extracting info (229 bytes)c1310-k9w7-mx.122-15.JA1/ (directory) 0 (bytes)c1310-k9w7-mx.122-15.JA1/html/ (directory) 0 (bytes)c1310-k9w7-mx.122-15.JA1/html/level1/ (directory) 0 (bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/appsui.js (558 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/back.htm (205 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/cookies.js (5027 bytes).extracting c1310-k9w7-mx.122-15.JA1/html/level1/forms.js (15704 bytes)...extracting c1310-k9w7-mx.122-15.JA1/html/level1/sitewide.js (14621 bytes)...extracting c1310-k9w7-mx.122-15.JA1/html/level1/config.js (2554 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/stylesheet.css (3215 bytes)c1310-k9w7-mx.122-15.JA1/html/level1/images/ (directory) 0 (bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/ap_title_appname.gif (1422 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_1st.gif (1171 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_cbottom.gif (318 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_current.gif (348 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_last.gif (386 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_last_filler.gif (327 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_last_flat.gif (318 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_button_nth.gif (1177 bytes)extracting c1310-k9w7-mx.122-15.JA1/html/level1/images/apps_leftnav_dkgreen.gif (869 bytes)-- MORE --If you do not press the spacebar to continue, the process eventually times out and the access point stops inflating the image.
Step 8 Enter the set BOOT command to designate the new image as the image that the access point uses when it reboots. The access point creates a directory for the image that has the same name as the image, and you must include the directory in the command. Your entry might look like this example:
bridge: set BOOT flash:/c1310-k9w7-mx.122-15.JA1/c1310-k9w7-mx.122-15.JA1
Step 9 Enter the set command to check your bootloader entries.
bridge: set
BOOT=flash:/c1310-k9w7-mx.122-15.JA1/c1310-k9w7-mx.122-15.JA1DEFAULT_ROUTER=192.168.133.1IP_ADDR=192.168.133.160NETMASK=255.255.255.0Step 10 Enter the boot command to reboot the access point. When the access point reboots, it loads the new image.
bridge: boot
Obtaining the Access Point/Bridge Image File
You can obtain the access point/bridge image file from the Cisco.com software center by following these steps:
Step 1 Use your Web-browser to go to the Cisco Software Center at the following URL:
http://www.cisco.com/cisco/software/navigator.html
Step 2 Select Option #1: Aironet Wireless Software Selector.
Step 3 For the Product Type, select Wireless Bridge and click Submit.
Step 4 Select 1300 Series for the model number and click Submit.
Step 5 Select Current Release (Recommended) and click Submit.
Step 6 Select c1310-k9w7-tar.122-15.JA.tar, which is the access point/bridge image file.
Step 7 On the Encryption Authorization Form, enter the requested information, read the encryption information, and check the boxes that apply. Click Submit.
Step 8 Read and accept the terms and conditions of the Software License Agreement.
Step 9 Select the access point/bridge image file again to download it.
Step 10 Save the file to a directory on your hard drive and then exit the Internet browser.
Obtaining the TFTP Server Software
You can download TFTP server software from several web sites. Cisco recommends the shareware TFTP utility available at this URL:
Follow the instructions on the website for installing and using the utility.