PDF(68.6 KB) View with Adobe Reader on a variety of devices
Updated:March 13, 2015
Document ID:1458169321709402
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
EOL6193
Cisco
® announces the end-of-sale and end-of life dates for the Cisco 7206VXR Router NPE-400 Bundles (Non-Security). The last day to order the affected bundle(s) is February 29, 2008. Customers with active service contracts will continue to receive support from the Cisco Technical Assistance Center (TAC) as shown in Table 1 of the EoL bulletin. Table 1 describes the end-of-life milestones, definitions, and dates for the affected product(s). Table 2 lists the product part numbers affected by this announcement. For customers with active and paid service and support contracts, support will be available until the termination date of the contract, even if this date exceeds the Last Date of Support shown in Table 1.
Table 1. End-of-Life Milestones and Dates for the Cisco 7206VXR Router NPE-400 Bundles (Non-Security)
Milestone
Definition
Date
End-of-Life Announcement Date
The date the document that announces the end of sale and end of life of a product is distributed to the general public.
August 31, 2007
End-of-Sale Date
The last date to order the product through Cisco point-of-sale mechanisms. The product is no longer for sale after this date.
February 29, 2008
Last Ship Date: HW
The last-possible ship date that can be requested of Cisco and/or its contract manufacturers. Actual ship date is dependent on lead time.
May 29, 2008
End of Routine Failure Analysis Date: HW
The last-possible date a routine failure analysis may be performed to determine the cause of product failure or defect.
February 28, 2009
End of New Service Attachment Date: HW
For equipment and software that is not covered by a service-and-support contract, this is the last date to order a new service-and-support contract or add the equipment and/or software to an existing service-and-support contract.
February 28, 2009
End of Service Contract Renewal Date: HW
The last date to extend or renew a service contract for the product.
May 26, 2012
Last Date of Support: HW
The last date to receive service and support for the product. After this date, all support services for the product are unavailable, and the product becomes obsolete.
February 27, 2013
HW = Hardware
OS SW = Operating System Software
App. SW = Application Software
Table 2. Product Part Numbers Affected by This Announcement
End-of-Sale Product Part Number
Product Description
Replacement Product Part Number
Replacement Product Description
C7206VXR/400/2FE
7206VXR with NPE-400 and I/O Controller with 2 FE/E Ports
7204VXR/400
7204VXR with NPE-400 and I/O Controller with 2FE/E Ports
C7206VXR/400/2FE
7206VXR with NPE-400 and I/O Controller with 2 FE/E Ports
7206VXR/NPE-G1
7206VXR with NPE-G1 includes 3GigE/FE/E Ports and IP SW
C7206VXR/400/2FE
7206VXR with NPE-400 and I/O Controller with 2 FE/E Ports
7206VXR/NPE-G2
7206VXR with NPE-G2 includes 3GigE/FE/E Ports and IP SW
C7206VXR/400/2FE
7206VXR with NPE-400 and I/O Controller with 2 FE/E Ports
7206-IPV6/ADSVC/K9
Cisco 7206VXR IPv6/Adv.Ent. Services bundle with NPE-G2
C7206VXR/400/GE
7206VXR with NPE-400 and GE+E I/O controller
7204VXR/400
7204VXR with NPE-400 and I/O Controller with 2FE/E Ports
C7206VXR/400/GE
7206VXR with NPE-400 and GE+E I/O controller
7206VXR/NPE-G1
7206VXR with NPE-G1 includes 3GigE/FE/E Ports and IP SW
C7206VXR/400/GE
7206VXR with NPE-400 and GE+E I/O controller
7206VXR/NPE-G2
7206VXR with NPE-G2 includes 3GigE/FE/E Ports and IP SW
C7206VXR/400/GE
7206VXR with NPE-400 and GE+E I/O controller
7206-IPV6/ADSVC/K9
Cisco 7206VXR IPv6/Adv.Ent. Services bundle with NPE-G2
C7206VXR/VOICE/400
7206VXR w/ NPE-400, Voice PA PA-VXC-2TE1+, I/O contlr w/ 2FE
7204VXR/400
7204VXR with NPE-400 and I/O Controller with 2FE/E Ports-to configure with PA-VXC-2TE1+ if required
C7206VXR/VOICE/400
7206VXR w/ NPE-400, Voice PA PA-VXC-2TE1+, I/O contlr w/ 2FE
7206VXR/NPE-G1
7206VXR with NPE-G1 includes 3GigE/FE/E Ports and IP SW-to configure with PA-VXC-2TE1+ if required
C7206VXR/VOICE/400
7206VXR w/ NPE-400, Voice PA PA-VXC-2TE1+, I/O contlr w/ 2FE
7206VXR/NPE-G2
7206VXR with NPE-G2 includes 3GigE/FE/E Ports and IP SW-to configure with PA-VXC-2TE1+ if required
C7206VXR/VOICE/400
7206VXR w/ NPE-400, Voice PA PA-VXC-2TE1+, I/O contlr w/ 2FE
7206-IPV6/ADSVC/K9
Cisco 7206VXR IPv6/Adv.Ent. Services bundle with NPE-G2-to configure with PA-VXC-2TE1+ if required
Product Migration Options
Customers are encouraged to migrate from the Cisco 7206VXR Router NPE-400 end-of-sale bundles (the C7206VXR/400/GE, C7206VXR/400/2FE, and C7206VXR/VOICE/400) to the higher-performing Cisco 7200VXR solutions with either the NPE-G2 or NPE-G1 Network Processing Engine. The Cisco 7200VXR solutions with NPE-G2 and NPE-G1 also offer more flexibility through support of the port adapter jacket card that makes use of the I/O controller card slot on the 7200VXR chassis and supports high-bandwidth point port adapters including the high-performing encryption module C7200-VSA (with NPE-G2).
The new Cisco 7200 NPE-400 bundle based on the Cisco 7204VXR 4-slot chassis (part number 7204VXR/400) is priced at the same level but offers a higher-performing engine than the end-of-sale NPE-225 bundle (part number 7204VXR/CPE). At this attractive pricing, the 7204VXR/400 bundle is the new entry-level solution in Cisco's midrange routing portfolio.
Customers can use the Cisco Technology Migration Plan (TMP) to trade in products and receive credit toward the purchase of new Cisco equipment. For more information about Cisco TMP, go to
http://www.cisco.com/go/tradein/. The Cisco TMP application requires all users to have a Cisco.com user ID.
Customers may be able to continue to purchase the end-of-sale product through the Cisco Certified Refurbished Equipment program. Refurbished units of the end-of-sale product are available in limited supply for sale in certain countries on a first-come, first-served basis. For information about the refurbished equipment program, go to
http://cisco.com/go/remarketing