Document ID: 12863 |
Introduction
This document lists questions and answers about errors that can occur when you log in or Telnet to a Cisco 675 Customer Premises Equipment (CPE).
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Q. I cannot Telnet or log in to the Cisco 675 from the network (WAN) side. Why?
A. Verify that the interface is trained, open, and that there are no hardware problems on the Cisco 675, digital subscriber line access multiplexer (DSLAM), or the network that connects them.
Make sure the Cisco 675 Wan0-0 interface is trained.
cbos#show int IP Address Mask eth0 10.10.33.2 255.255.255.0 vip0 0.0.0.0 255.255.255.0 vip1 0.0.0.0 255.255.255.0 vip2 0.0.0.0 255.255.255.0 wan0 Physical Port: Not Trained Dest IP Address Mask wan0-0 10.1.1.1 255.255.255.255 cbos#Make sure the Cisco 675 Wan0-0 interface is not in a closed state.
cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 1, VCI 1) is configured. ScalaRate set at 1088 Kbps AAL 5 UBR Traffic RFC1483 State: CLOSED !--- The virtual circuit is closed. Local MRU: 2048 RFC1483 Tx: 2563 RFC1483 Rx: 1603807 CDP Packets: 0 Number of Spantree Packets: 0 Number of Unknown Packets: 0 IP Port EnabledIf the interface is closed, open it then verify that the state changed.
cbos#set int wan0-0 open Opening connection wan0-0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 1, VCI 1) is open. ScalaRate set at 1088 Kbps AAL 5 UBR Traffic RFC1483 State: OPENED Local MRU: 2048 RFC1483 Tx: 66 RFC1483 Rx: 215 CDP Packets: 0 Number of Spantree Packets: 0 Number of Unknown Packets: 0 IP Port EnabledIf the interface fails to open and trainup, then issue write and reboot commands.
Q. Why do I get this error when I Telnet from the network (WAN) side of the Cisco 675? Access-6400-NRP1#telnet 10.10.33.2 Trying 10.10.33.2 ... Open Connection refused, password not set. configure password via serial port to proceed. [Connection to 10.10.33.2 closed by foreign host] Access-6400-NRP1#
A. You need a password to use Telnet, TFTP, HTTP or Syslog on the Cisco 675. Assign an EXEC password to the Cisco 675. Complete these steps:
- Issue the show run command.
cbos#show run [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, username PPP Port User Password = 00, password PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable,IP,0.0.0.0 [[ IP Routing = Section Start ]] IP Port Remote Address = 01, 10.1.1.1 IP NAT = enabled IP Port Address = 00, 10.10.33.2 [[ Spanning Tree = Section Start ]] MAC Bridge Management = enabled MAC Bridge = enabled, rfc1483 [[ CBOS = Section Start ]] NSOS 1483 Routing = enabled [[ DHCP = Section Start ]] DHCP Relay = disabled [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 1, 1, 0- Set the EXEC password.
cbos#set password exec <password> Exec Password Change Successful!- Issue the show run command again to verify that the EXEC password was assigned.
cbos#show run [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, username PPP Port User Password = 00, password PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable,IP,0.0.0.0 [[ IP Routing = Section Start ]] IP Port Remote Address = 01, 10.1.1.1 IP NAT = enabled IP Port Address = 00, 10.10.33.2 [[ Spanning Tree = Section Start ]] MAC Bridge Management = enabled MAC Bridge = enabled, rfc1483 [[ CBOS = Section Start ]] NSOS 1483 Routing = enabled NSOS Root Password = n_qqumpb !--- Note the password assignment. [[ DHCP = Section Start ]] DHCP Relay = disabled [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 1, 1, 0Note: If you set an EXEC password, you should also set an enable password. Otherwise, you will be at a security risk. This is also true for the Cisco 675 console port.
- Set the enable password.
cbos#set password enable <password> Enable Password Change Successful!- Issue the show run command again to verify that the enable password was assigned.
cbos#show run [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, username PPP Port User Password = 00, password PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable,IP,0.0.0.0 [[ IP Routing = Section Start ]] IP Port Remote Address = 01, 10.1.1.1 IP NAT = enabled IP Port Address = 00, 10.10.33.2 [[ Spanning Tree = Section Start ]] MAC Bridge Management = enabled MAC Bridge = enabled, rfc1483 [[ CBOS = Section Start ]] NSOS 1483 Routing = enabled NSOS Root Password = n_qqumpb NSOS Enable Password = n_qqumpb !--- Note the enable password assignment. [[ DHCP = Section Start ]] DHCP Relay = disabled [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 1, 1, 0
Q. How do I remove the EXEC and enable passwords?
A. Issue the set password clear enable and set password clear enable commands, and then issue a show run command to verify that the passwords were cleared.
cbos#set password clear enable Enable Password Cleared cbos#set password clear exec Exec Password Cleared cbos#show run [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, username PPP Port User Password = 00, password PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable,IP,0.0.0.0 [[ IP Routing = Section Start ]] IP Port Remote Address = 01, 10.1.1.1 IP NAT = enabled IP Port Address = 00, 10.10.33.2 [[ Spanning Tree = Section Start ]] MAC Bridge Management = enabled MAC Bridge = enabled, rfc1483 [[ CBOS = Section Start ]] NSOS 1483 Routing = enabled NSOS Enable Password = NSOS Root Password = !--- Note that the passwords are cleared. [[ DHCP = Section Start ]] DHCP Relay = disabled [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 1, 1, 0
Q. What should I do when I Telnet and I see this display? Access-6400-NRP1#telnet 10.10.33.2 Trying 10.10.33.2 ...
A. If the Cisco 675 is in bridging mode, you must turn on bridging management.
cbos#set bridging managment enabled You must use "write" then reboot for changes to take effect. cbos#write NVRAM written. cbos#reboot Hello! Expanding CBOS image... CBOS v2.2.0.000 User Access Verification Password:In order to turn off bridging management:
cbos#set bridging managment disabled You must use "write" then reboot for changes to take effect. cbos#write NVRAM written. cbos#reboot Hello! Expanding CBOS image... CBOS v2.2.0.000 User Access Verification Password:
Cisco Support Community - Featured Conversations
Related Information
- Asymmetric Digital Subscriber Line (ADSL) Support Pages
- Technical Support & Documentation - Cisco Systems
| Updated: Jun 01, 2005 | Document ID: 12863 |