Document ID: 22977
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Configure
Network Diagram
Configurations
MGX 8220 IMATM-8T1/B - Local Feeder (fdr8220)
MGX 8220 FRSM - Local Feeder (fdr8220)
MGX 8220 ASC - Local Feeder (fdr8220)
MGX 8220 IMATM-8T1/B - Remote Feeder (remfdr)
MGX 8220 FRSM - Remote Feeder (remfdr)
MGX 8220 ASC - Remote Feeder (remfdr)
BPX 8600
MC 3810 Routers
show Commands
MGX 8220 IMATM-8T1/B (fdr8220)
MGX 8220 FRSM-8T1 (fdr8220)
MGX 8220 ASC (fdr8220)
MC 3810 Router (r3810a)
MGX 8220 IMATM-8T1/B (remfdr)
MGX 8220 FRSM-8T1 (remfdr)
MGX 8220 ASC - Remote Feeder (remfdr)
MC 3810 Router (r3810b)
BPX 8600
Troubleshoot
NetPro Discussion Forums - Featured Conversations
Related Information
Introduction
This document provides configuration information for a remote feeder shelf application that uses inverse multiplexing for ATM (IMATM) to support two Frame Relay devices.
This configuration allows the use of narrowband connectivity between a Cisco MGX 8220 Edge Concentrator and a Cisco BPX 8600 Switch. The remote MGX 8220 is connected to the BPX 8600 through a four T1 IMA group on a local MGX 8220. The BPX 8600 provides switching service between two Cisco MC 3810 routers that use a network interworking (NIW) connection.
This document can help you configure Cisco equipment. It is not a substitute for proper network design and planning. See your Cisco sales engineer, systems engineer, or account manager for help with your network plan and design.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The versions used in this document are based on available releases. They are not intended to be strict requirements. You can read the release notes to verify that the required interfaces and the configurations are supported on each of the platforms.
-
MC 3810
Software—Cisco IOS® Software Release 12.0(3) and 12.0(4)T.
Hardware—Cisco MC 3810 with T1 multiflex trunk (MFT) interface.
-
MGX 8220
Both Cisco MGX 8220 edge concentrators use the same Cisco firmware release and hardware configuration.
Firmware—Cisco MGX 8220 Version 5.0.14 Firmware Release and the appropriate versions of service module hardware and firmware on both the MGX 8220.
Hardware—The Cisco inverse multiplexing for ATM (IMATM) model B service module is used for ATM Forum compliant IMA. Four T1 trunks are used to make the connection between the two 8-port IMATM/B service modules on each of the MGX 8220 edge concentrators. The IMATM/B service modules use RJ48 connectors.
On the remote MGX 8220 edge concentrator, the T3 port on the IMATM/B service module is connected to the T3 port on the Broadband Network Module (BNM)-T3 service module. The IMATM/B and the BNM-T3 service modules each use coaxial T3 connectors.
The FRSM-8T1 service module uses RJ48 connectors.
-
BPX 8600
Software—Cisco WAN Switching System Software Release 9.2.34 and the appropriate versions of card hardware and firmware as specified in the Release Notes.
Hardware—The BPX 8600 is connected to the local MGX 8220 feeder shelf with a BNI-T3 card set. The BPX 8600 is connected to the remote MGX 8220 feeder shelf with a BXM-T3 card set. The BXM-T3 card set is connected to a local MGX 8220 IMATM/B service module T3 connector.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, refer to Cisco Technical Tips Conventions.
Configure
Note: To find additional information on the commands used in this document, use the Command Lookup Tool ( registered customers only) .
Network Diagram
This document uses this network setup:
Configurations
Make all physical connections before you create configurations.
Note: To find additional information on the commands used in this document, use the Command Lookup Tool ( registered customers only) .
MGX 8220 IMATM-8T1/B - Local Feeder (fdr8220)
Add these lines to the IMATM-8T1/B card that will be included in the IMATM group:
fdr8220.1.7.IMATMB.a > addln 1 fdr8220.1.7.IMATMB.a > addln 2 fdr8220.1.7.IMATMB.a > addln 3 fdr8220.1.7.IMATMB.a > addln 4
Check all lines and clear alarms before you create an IMA group. Cisco advices you to use contiguous lines in an IMA group, however it is not required. An IMA group can consist of lines 1, 3, 4, and 5.
Note: Line framing and line coding for T1s between the two IMATM-8T1/B service modules must match.
fdr8220.1.7.IMATMB.a > dsplns
Line Conn Type Status/Coding Length XmtClock Alarm Stats
Type Source Alarm
---- ----- --------- -------------- --------- -------- ----- -----
7.1 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.2 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.3 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.4 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.5 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
7.6 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
7.7 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
7.8 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
LineNumOfValidEntries: 8
fdr8220.1.7.IMATMB.a > dspalms -ds1
Line AlarmState StatisticalAlarmState
---- ----------- ---------------------
7.1 No Alarms No Statistical Alarms
7.2 No Alarms No Statistical Alarms
7.3 No Alarms No Statistical Alarms
7.4 No Alarms No Statistical Alarms
Add the IMA group and the above lines into the group
fdr8220.1.7.IMATMB.a > addimagrp 1 1 1.2.3.4 2
where:
1 |
IMA group number -- value ranging from 1 to 8 |
1 |
Port Type -- 1- UNI, 2- NNI, 3- STI, 4- Virtual trunks UNI(STI in UNI) |
1.2.3.4 |
List of links -- list of links separated by dots |
2 |
minimum no of links -- minimum number of links for the group formation :value ranging from 1 to 8. This number must be the same at each end of the IMA group. |
If the IMA group does not clear alarm after it is added at each end of the network, add a one-trunk IMA group and successive trunks one-by-one. Issue the addchrte command to add a channel route for the IMA group. This command creates a virtual path identifier (VPI) map listing on the IMATM-8T1/B and defines which cells are routed to a particular IMA group. If a channel route is not added for an IMA group, all cells are discarded as unknown vpi_vci cells. If a single IMA group is defined, and the VPI range that is sent from the attached equipment is not known, then specify the entire VPI range.
fdr8220.1.7.IMATMB.a > addchrte 1 1 0 255
where:
1 |
Range number -- value ranging from 1 to 128 |
1 |
IMA trunk number -- value ranging from 1 to 8 |
0 |
Min. VPI value -- 0-255 (UNI/VpTrkUNI), 0-1023(STI), 0-4095(NNI) |
255 |
Max. VPI value -- 0-255 (UNI/VpTrkUNI), 0-1023(STI), 0-4095(NNI) In this case, the port type is UNI so the max. value of 255 is used. |
Verify the cell framing and payload scrambling settings on the T3 line. The payload scrambling setting must match the BPX 8600 BXM-T3. Payload scrambling ensures that the ATM cell payload does not resemble the cell header. It is only significant locally. Specifically, each side of an ATM interface must have the same payload scrambling value, but all ATM interfaces in the network do not require the same configuration.
fdr8220.1.7.IMATMB.a > dspplcpln 1 PLCP CellFraming PayloadScramble PlcpLoopback ---- ----------- --------------- ------------ 7.1 PLCP Disabled None PLCPNumOfValidEntries: 1
Configure the clock sources on the MGX 8220 IMATM-8T1/B. The primary clock source is set to the DS3 line from the BPX 8600. The secondary source is set to the back plane clock. For more information, refer to Configuring the Clock Source.
fdr8220.1.7.IMATMB.a > cnfclksrc -pri 9 -sec 10 -cur 1
where:
-pri 9 |
–pri PrimaryClockSource = 1 - 10 1-8: DS1 Line1 thru Line8, 9: DS3 Line, 10: Back Plane Clock |
-sec 10 |
-sec SecondaryClockSource = 1 - 11 1-8: DS1 Line1 thru Line8, 9: DS3 Line, 10: Back Plane Clock, 11: Not Configured |
-cur 1 |
-cur CurrentClockSource = 1 - 3 1: Primary 2: Secondary 3: Hold |
Note: This sample configuration was tested in a lab with this specific clock setting. The default setting or other clock settings also may be used, depending upon the design of the network. For more information on network synchronization, refer to WAN Switching Network Synchronization Fundamentals.
MGX 8220 FRSM - Local Feeder (fdr8220)
Verify existing lines.
fdr8220.1.9.FRSM.a > dsplns
Line Conn Type Status/Coding Length XmtClock Alarm Stats
Type Source Alarm
---- ----- --------- ------ ------ -------- -------- ----- -----
9.1 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.2 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.3 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.4 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.5 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.6 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.7 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.8 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
LineNumOfValidEntries: 8
Enable the line connected to the Cisco MC 3810 router.
Note: Line framing and line coding for the T1 between the FRSM and MC 3810 must match.
fdr8220.1.9.FRSM.a > addln 1
Enable the logical port and configure it for Frame Relay service.
fdr8220.1.9.FRSM.a > addport 1 1 2 1 24 1
where:
1 |
port number -- values ranging from 1-192 are accepted for T1 and 1-2481 |
1 |
line number -- value ranging from 1 to 8 |
2 |
DS0 speed -- 1 for 56K, 2 for 64K |
1 |
beginning slot -- beginning time slot in 1 base |
24 |
number of slot -- number of DS0 time slots assigned to |
1 |
port type -- values 1-3, 1=frame relay, 2=FUNI mode-1a, 3=frForward |
Configure the logical port to use local management interface (LMI) signaling. This example uses StrataLMI with asynchronous updates enabled and enhanced LMI disabled:
fdr8220.1.9.FRSM.a > cnfport 1 S y n
where:
1 |
port number -- values ranging from 1-192 are accepted for T1 and 1-2481 |
S |
LMI signaling -- (N)one (S)trataLMI au-AnnexAUNI du-AnnexDUNI an-AnnexANNI dn-AnnexDNNI.Must match LMI on MC3810 |
y |
asyn UPD/UFS -- (UPD = Update Status, UFS = Unsolicited Full Status) (n or 1) = both dis, (y or 2) = UPD en, 3 = UFS en, 4 = both en |
n |
Enhanced LMI -- (N or n) disable (Y or y) enable |
Display and verify the configuration of the logical port.
fdr8220.1.9.FRSM.a > dspports
Port Ena/Speed EQServ SignalType T391 T392 N391 N392 N393 Type I
Ratio
------ --- ----- ------ ------------ ---- ---- ---- ---- ---- ---------
9.1.1 Mod/1536 Kbps 1 StrataLMI 10 15 6 3 4 frameRel
Number of ports: 1
PortDs0UsedLine1: 0x00ffffff
PortDs0UsedLine2: 0x00000000
PortDs0UsedLine3: 0x00000000
PortDs0UsedLine4: 0x00000000
PortNumNextAvailable: 7
Now add the connection and enable network internetworking function.
Note: Connection values are not optimized and are used as an example only.
fdr8220.1.9.FRSM.a > addchan 300 1 300 1536000 1
where:
300 |
channel number -- value ranging from 16 to 1015 |
1 |
port number -- values ranging from 1-192 are accepted for T1 and 1-2481 |
300 |
DLCI number -- value ranging from 0 to 1023. Must match DLCI on MC3810. |
1536000 |
committed rate -- 0-1536000 bps for T1; 0-2048000 BPS for E1 |
1 |
chan type -- values 1-5, 1=NIW 2=SIW-transparent 3=SIW-xlation 4=FUNI 5=frForward |
MGX 8220 ASC - Local Feeder (fdr8220)
Verify the interface format for the BNM-T3 trunk card. This example uses the default format of bnmSti because the local feeder connects to the BPX 8600 BNI-T3 card set. The BPX 8600 BNI-T3 card set only supports the Stratacom Trunk Interface (STI) format.
fdr8220.1.4.ASC.a > dspbnmif bnmLineInterfaceFormat: bnmSti
Verify the clock sources on the ASC. The primary clock source should be set to the BNM-T3, which is shown as Inband from BNM.
fdr8220.1.4.ASC.a > dspclksrc PrimaryClockSource: Inband from BNM SecondaryClockSource: Internal Oscillator CurrentClockSource: Inband from BNM ClockSwitchState: SrcChanged ExtClkPresent: Not Present ExtClkSrcImpedance: 75 ohms ExtClkConnectorType: BNC
Verify the cell framing and payload scrambling settings on the T3 line. The payload scrambling setting must match that of the BPX 8600 BNI-T3. Payload scrambling was developed to ensure that ATM cell payload does not resemble a cell header. Payload scrambling is only significant locally. Specifically, each side of an ATM interface must have the same payload scrambling value, but all ATM interfaces in the network do not require the same configuration.
fdr8220.1.4.ASC.a > xdspln -plcp 1 PLCP CellFraming PayloadScramble ---- ----------- --------------- 2.1 PLCP Disabled PLCPNumOfValidEntries: 1
MGX 8220 IMATM-8T1/B - Remote Feeder (remfdr)
The configuration for the remote feeder is similar to the local feeder IMATM-8T1/B configuration. The configuration settings that are different than those of the local feeder are provided here.
Verify cell framing and payload scrambling parameters on the DS3. The settings must match those on the remote BNM-T3, which resides on the same MGX 8220.
remfdr.1.8.IMATMB.a > dspplcpln 1 PLCP CellFraming PayloadScramble PlcpLoopback ---- ----------- --------------- ------------ 8.1 PLCP Disabled None PLCPNumOfValidEntries: 1
Configure the clock source on the IMATM-8T1/B. The primary clock source is configured for the DS1. The secondary source is configured for the back plane clock. Configure all DS1 lines in the IMA group for Loop Clock to recover clock from the T1 receive.
The clock configuration for a DS1 line can only be changed before the DS1 line is added to the IMA group. In order to change the clock configuration for DS1 lines that are part of an active IMA group, the entire IMA group needs to be deleted.
remfdr.1.8.IMATMB.a > cnfln 1 2 10 1
where:
1 |
line number -- values ranging from 1-8 |
2 |
line code -- 2 for B8ZS (T1),3 for HDB3 (E1),4 for AMI (T1/E1) |
10 |
line length -- 10-15 for T1, 8 for E1 with SMB module,9 for E1 with RJ48 line module |
1 |
clock source -- clock source : 1 for loop clock, 2 for local clock |
remfdr.1.8.IMATMB.a > cnfln 2 2 10 1 remfdr.1.8.IMATMB.a > cnfln 3 2 10 1 remfdr.1.8.IMATMB.a > cnfln 4 2 10 1
Now configure the clock source for the IMATM-8T1/B.
remfdr.1.8.IMATMB.a > cnfclksrc -pri 1 -sec 10 -cur 1
where:
-pri 1 |
-pri PrimaryClockSource = 1 - 10 1-8: DS1 Line1 thru Line8, 9: DS3 Line, 10: Back Plane Clock |
sec 10 |
-sec SecondaryClockSource = 1 - 11 1-8: DS1 Line1 thru Line8, 9: DS3 Line, 10: Back Plane Clock, 11: Not Configured |
-cur 1 |
-cur CurrentClockSource = 1 - 3 1: Primary 2: Secondary 3: Hold |
Note: This sample configuration was tested in a lab with this specific clock setting. You can use the default setting or other clock settings, depending upon the network design. For more information on network synchronization, refer to WAN Switching Network Synchronization Fundamentals.
MGX 8220 FRSM - Remote Feeder (remfdr)
All configuration steps for the remote feeder FRSM are identical to the local feeder FRSM. For more details, see the MGX 8220 FRSM - Local Feeder (fdr8220) section of this document.
MGX 8220 ASC - Remote Feeder (remfdr)
Verify the interface format for the BNM-T3 trunk card. This example requires a format change to the user-network interface (UNI) because the distant end connects with the IMATM-8T1/B and the BXM-T3. The BXM-T3 does not support the STI format.
Note: You cannot configure the BNM interface if connections exist on the MGX 8220 shelf. After you configure the BNM interface, the MGX 8220 shelf resets.
remfdr.1.3.ASC.a > dspbnmif bnmLineInterfaceFormat: bnmSti remfdr.1.3.ASC.a > cnfbnmif -if 2
where:
2 |
interfaceFormat = 1-3, 1: STI, 2: UNI, 3: NNI |
Verify the cell framing and payload scrambling settings on the T3 line. The payload scrambling setting must match that of the BPX 8600 BXM-T3.
remfdr.1.3.ASC.a > xdspln -plcp 1 PLCP CellFraming PayloadScramble ---- ----------- --------------- 1.1 PLCP Disabled PLCPNumOfValidEntries: 1
BPX 8600
Add the local MGX 8220 as a feeder shelf to the BPX 8600 switch. Issue the uptrk command in order to activate the T3 trunk.
bpx8600 TRM SuperUser BPX 8620 9.2.34 Oct. 31 2000 23:45 PST TRK Type Current Line Alarm Status Other End 2.1 T3 Clear - OK - Last Command: uptrk 2.1 Next Command: |
Check the trunk and clear alarms. Once the trunk is clear of alarms, issue the addshelf command.
bpx8600 TRM SuperUser BPX 8620 9.2.34 Oct. 31 2000 23:48 PST
BPX 8620 Interface Shelf Information
Trunk Name Type Part Id Ctrl Id Control_VC Alarm
VPI VCIRange
2.1 a3 AXIS - - - - MIN
Last Command: addshelf 2.1 A
Shelf has been added
Next Command:
|
Add the remote MGX 8220 as a feeder shelf to the BPX 8600 switch. Issue the uptrk command in order to activate the T3 trunk.
bpx8600 TRM SuperUser BPX 8620 9.2.34 Oct. 31 2000 23:50 PST TRK Type Current Line Alarm Status Other End 2.1 T3 Clear - OK fdr8220(AXIS) 13.1 T3 Clear - OK - Last Command: uptrk 13.1 Next Command: |
Check the trunk and clear alarms. Once the trunk is clear of alarms, issue the addshelf command.
bpx8600 TRM SuperUser BPX 8620 9.2.34 Oct. 31 2000 23:50 PST
BPX 8620 Interface Shelf Information
Trunk Name Type Part Id Ctrl Id Control_VC Alarm
VPI VCIRange
2.1 fdr8220 AXIS - - - - MIN
13.1 remfdr AXIS - - - - MIN
Last Command: addshelf 13.1 A
Shelf has been added
Next Command:
|
Add the connection on the BPX 8600 switch with the addcon command. The connection values are not optimized and are used for this example only.
This command: addcon 2.1.9.300 bpx8600 13.1.11.100 atfr 3000 * * * * * * * *
where:
|
User Input |
Definition |
|---|---|
|
addcon |
Add a connection |
|
2.1.9.300 |
connection number -- <feeder_trunk_slot.feeder_trunk_port.FRSM_slot.FRSM_channel> |
|
bpx8600 |
remote node name -- repeat the name for locally switched connections. |
|
13.1.11.100 |
connection number -- <remote_feeder_trunk_slot.remote_feeder_trunk_port.FRSM_slot.FRSM_channel> |
|
atfr |
connection type -- ATM (at) to Frame Relay (fr) |
|
3000/3000 |
PCR (0 + 1) [50/50] -- Peak Cell Rate. Equivalent to Frame Relay peak information rate (PIR) for cell loss priority (CLP) 0 and CLP=1 traffic. Default value is 50 in both transmit and receive directions. |
|
100/100 |
% Util [100/100] -- Percent utilization. Default value is 100 in both transmit and receive directions. |
|
25000/25000 |
CDVT (0 + 1) [250000/250000] -- Cell Delay Variation Tolerance. Default value is 250000 in both transmit and receive directions. |
|
3000/3000 |
SCR [50/50] -- Sustainable Cell Rate. Equivalent to Frame Relay committed information rate (CIR). Default value is 50 in both transmit and receive directions. |
|
1000/1000 |
MBS [1000/1000] -- Maximum Burst Size. Equivalent to Frame Relay excess burst size (Be). Default value is 1000 in both transmit and receive directions. |
|
3 |
Policing [3] -- The algorithm used to determine conformance to traffic contract. Default value is 3 for ATM Forum Traffic Management Specification Version 4.0 VBR.3. |
|
1280/1280 |
VC Qdepth [1280/1280] -- Virtual Connection Queue Depth. Default value is 1280 in both transmit and receive directions. |
|
35/35 |
EFCI [35/35] -- Explicit Forward Congestion Indication. Equivalent to Frame Relay forward explicit congestion notification (FECN). Configured per port queue for the BXM. Default value is 35 in both transmit and receive directions. |
|
1/1 |
IBS [1/1] -- Initial Burst Size. Equivalent to Frame Relay Cmax. Default value is 1 in both transmit and receive directions. |
MC 3810 Routers
Both Cisco MC 3810 routers have identical configurations except for the data link connection identifier (DLCI). The DLCI for the local MC 3810 is 300. The DLCI for the remote MC 3810 is 100.
Configure the Frame Relay interface and assign an IP address. All output from the show command is in the show Command section of this document.
r3810b#conf t r3810b(config)#cont t1 0 r3810b(config-controller)#framing esf r3810b(config-controller)#linecode b8zs r3810b(config-controller)#channel-group 1 timeslots 1-24 speed 64 r3810b(config-controller)#no shut r3810b(config-controller)#int s0:1 r3810b(config-if)#ip address 1.1.1.1 255.255.255.0 r3810b(config-if)#encapsulation frame-relay r3810b(config-if)#frame-relay map ip 1.1.1.3 300 broadcast !--- Associate the DLCI to the IP address. r3810b(config-if)#no shut
show Commands
MGX 8220 IMATM-8T1/B (fdr8220)
Command summary:
Certain show commands are supported by the Output Interpreter Tool ( registered customers only) , which allows you to view an analysis of show command output.
-
version
-
dsplns
-
dspdsx3lns
-
dspln
-
dspports
-
dspimagrp
-
dspimainfo
-
dspplpp
-
dspimalncnt
-
dspimaln
-
dspimagrpcnt
-
dspclksrc
fdr8220.1.7.IMATMB.a > version
***** Cisco Systems, Inc. AXIS IMATM Card *****
Firmware Version = 5.0.12
Backup Boot version = IMA_BT_1.0.02
IMATM Xilinx file = imatm_b_xilinx.h
VxWorks (for Cisco Systems, Inc.) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Thu Jun 22 11:22:38 PDT 2000.
Boot line:
fdr8220.1.7.IMATMB.a > dsplns
Line Conn Type Status/Coding Length XmtClock Alarm Stats
Type Source Alarm
---- ----- ------------ ------ -------- ------------- -------- ----- -----
7.1 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.2 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.3 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.4 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
7.5 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
7.6 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
7.7 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
7.8 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
LineNumOfValidEntries: 8
fdr8220.1.7.IMATMB.a > dspdsx3lns Line Type Coding Length Criteria AIScBitsCheck ---- -------------- -------- ------------- ----------- ------------- 7.1 dsx3CbitParity dsx3B3ZS LessThan225ft 3 out of 8 Ignore C-bits LineNumOfValidEntries: 1
fdr8220.1.7.IMATMB.a > dspln 1 LineNum: 1 LineConnectorType: RJ-48 LineType: dsx1ESF LineEnable: Enabled LineCoding: dsx1B8ZS LineLength: 0-131 ft LineXmtClockSource: LocalTiming LineLoopbackCommand: NoLoop LineSendCode: NoCode LineUsedTimeslotsBitMap: 0xffffffff LineLoopbackCodeDetection: codeDetectDisabled LineBERTEnable: Disable LineNumOfValidEntries: 8
fdr8220.1.7.IMATMB.a > dspports
No ATM T1/E1 UNI ports currently active
List of IMA groups:
===================
ImaGrp PortType Conf Avail Lines configured Lines present Tol Diff Port e
rate rate Delay(ms)
------ -------- ----- ------ --------------- --------------- --------- ------
7.1 UNI 14364 14364 1.2.3.4 1.2.3.4 275 Active
NextPortNumAvailable: 8
fdr8220.1.7.IMATMB.a > dspimagrp 1 IMA Group number : 1 Port type : UNI Lines configured : 1.2.3.4 Enable : Enabled IMA Port state : Active IMA Group Ne state : operational PortSpeed (cells/sec) : 14364 GroupTxAvailCellRate (cells/sec) : 14364 ImaGroupTxFrameLength(cells) : 128 LcpDelayTolerance (IMA frames) : 1 ReadPtrWrPtrDiff (cells) : 4 Minimum number of links : 1 MaxTolerableDiffDelay (msec) : 275 Lines Present : 1.2.3.4 Observed Diff delay (msec) : 0 Clock Mode : CTC GroupAlpha : 2 GroupBeta : 2 GroupGamma : 1 GroupConfiguration : 1 IMAGrp Failure status : No Failure Timing reference link : 1 ImaGroupTxImaId : 0x0 ExpectedGroupRxImaId : 0x0
fdr8220.1.7.IMATMB.a > dspimainfo
Link Group NeTx NeRx FeTx FeRx TxLID RxID
State State State State
------------------------------------------------------------------
1 1 Active Active Active Active 0 0
2 1 Active Active Active Active 1 1
3 1 Active Active Active Active 2 2
4 1 Active Active Active Active 3 3
fdr8220.1.7.IMATMB.a > dspplpp 1
PhysicalPortNumber: 1
CellFraming: ATM
CellScramble: No Scramble
Plpp Loopback: No Loopback
Single-bit error correction: Disabled
fdr8220.1.7.IMATMB.a > dspimagrpcnt 1
IMA Group number: 1
Ne Number of failures : 0
fdr8220.1.7.IMATMB.a > dspimalncnt 1 1 IMA group number : 1 Line number : 1 Icp Cells Received : 6735926 Icp Errored Cells Recvd : 0 Ima Violations Count : 0 Ima OIF anomalies : 0 Ima Ne Severely Errored Seconds : 0 Ima Fe Severely Errored Seconds : 1 Ima Ne Unavailable Seconds : 0 Ima Fe Unavailable Seconds : 0 Ima NeTx Unusable Seconds : 1 Ima NeRx Unusable Seconds : 1 Ima FeTx Unusable Seconds : 1 Ima FeRx Unusable Seconds : 1 Ima FeTx Num. Failues : 0 Ima FeRx Num. Failures : 0 # HEC errored cells : 0 # HEC errored seconds : 0 # Severely HEC errored seconds : 0
fdr8220.1.7.IMATMB.a > dspimaln 1 1 IMA Group number : 1 Link number : 1 ImaLink TxLId : 0x0 ImaLink RxLId : 0x0 LinkNeRxState : Active LinkNeTxState : Active LinkNeRxFailureStatus : No Failure LinkFeRxState : Active LinkFeTxState : Active LinkFeRxFailureStatus : No Failure LinkRelDelay : 0 LinkRxTestPattern : 255 Ne Link Tx Num Failures : 0 Ne Link Rx Num Failures : 0
fdr8220.1.7.IMATMB.a > dspimagrpcnt 1 IMA Group number: 1 Ne Number of failures : 0
fdr8220.1.7.IMATMB.a > dspclksrc PrimaryClockSource: DS3_LINE SecondaryClockSource: BP_8KHZ CurrentClockSource: PRIMARY
MGX 8220 FRSM-8T1 (fdr8220)
Command summary:
-
version
-
dsplns
-
dspports
-
dspchans
fdr8220.1.9.FRSM.a > version
***** Cisco Systems, Inc. AXIS FRSM-8P Card *****
Firmware Version = 5.0.13
Backup Boot version = FR8_BT_1.0.02
ASCFRSM Xilinx file = cbslave.h
VxWorks (for Cisco Systems, Inc.) version 5.2 Rev B.
Kernel: WIND version 2.4.
Made on Wed Jun 21 16:15:40 PDT 2000.
Boot line:
fdr8220.1.9.FRSM.a > dsplns
Line Conn Type Status/Coding Length XmtClock Alarm Stats
Type Source Alarm
---- ----- ------------ ------ -------- ------------- -------- ----- -----
9.1 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
9.2 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.3 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.4 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.5 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.6 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.7 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
9.8 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
LineNumOfValidEntries: 8
fdr8220.1.9.FRSM.a > dspports
Port Ena/Speed EQServ SignalType T391 T392 N391 N392 N393 Type AlarI
Ratio
-------- --- ----- ------ ------------ ---- ---- ---- ---- ---- -------- -----
9.1.1 Mod/1536k 1 StrataLMI 10 15 6 3 4 frameRel No f
Number of ports: 1
PortDs0UsedLine1: 0x00ffffff
PortDs0UsedLine2: 0x00000000
PortDs0UsedLine3: 0x00000000
PortDs0UsedLine4: 0x00000000
PortDs0UsedLine5: 0x00000000
PortDs0UsedLine6: 0x00000000
PortDs0UsedLine7: 0x00000000
PortDs0UsedLine8: 0x00000000
PortNumNextAvailable: 110
fdr8220.1.9.FRSM.a > dspchans
DLCI Chan EQ I/EQDepth I/EQDEThre I/EECNThre Fst/ DE Type Alarm
------------- ---- -- ----- ----- ----- ----- ----- ----- --- --- ----- -----
9.1.1.300 300 2 65535/65535 32767/32767 6553/6553 Dis/Dis NIW No
Number of channels: 1
ChanNumNextAvailable: 34
MGX 8220 ASC (fdr8220)
Command summary:
-
version
-
dsplns
-
dspcds
-
xdspln -plcp 1
-
dspbnmif
-
dspclksrc
fdr8220.1.4.ASC.a > version
***** Cisco Systems, Inc. AXIS ASC Card *****2
Firmware Version = 5.0.14
Backup Boot version = ASC_BT_1.0.03
ASCFRSM Xilinx file = asc025.h
ASC2 Xilinx file = ASC2_Xilinx.h
ASCBNM Xilinx file = A:bnm_a E:bnm_e
ASCBNM Altera file = bnm155_2
SRM-T1E1 Xilinx file = A:srm038.h, E:srmE038.h
SRM-3T3 Xilinx file = srm038.h
SRM-3T3 Encoder file = encoder42_004.ttf
SRM-3T3 Encoder-2 file = encoder80_001.ttf
SRM-3T3 Decoder file = decoder42_004.ttf
SRM-3T3 Clock file = clkctrl_40.ttf
SRM-3T3 I-Cube file = ic320.h
VxWorks (for Cisco Systems, Inc.) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Wed Jun 21 15:53:33 PDT 2000.
Boot line:
ln(0,0)
fdr8220.1.4.ASC.a > dsplns
Line Type Coding Length Criteria AIScBitsCheck
---- -------------- -------- ------------- ----------- -------------
2.1 dsx3CbitParity dsx3B3ZS LessThan225ft 3 out of 8 Check C-bits
LineNumOfValidEntries: 1
fdr8220.1.4.ASC.a > dspcds
Slot CardState CardType CardAlarm Redundancy
---- ----------- ------------ --------- ------------------
1.1 Empty
1.2 Active BNM-T3 Minor
1.3 Empty
1.4 Active ASC Minor
1.5 Active FRSM-4T1
1.6 Active FRSM-4T1
1.7 Active IMA-8T1/B
1.8 Active AUSM-4T1
1.9 Active FRSM-8T1
1.10 Empty
1.11 Active CESM-8T1
1.12 Empty
1.13 Empty
1.14 Empty
1.15 Empty
1.16 Active SRM-3T3
NumOfValidEntries: 16
NodeName: fdr8220
Date: 11/01/2000
Time: 11:55:28
TimeZone: PST
TimeZoneGMTOff: -8
StatsMasterIpAddress: 0.0.0.0
shelfIntegratedAlarm: Major
BkplnSerialNum:
BkplnType: 1
BkplnFabNumber:
BkplnHwRev: bb
fdr8220.1.4.ASC.a > xdspln -plcp 1 PLCP CellFraming PayloadScramble ---- ----------- --------------- 2.1 PLCP Disabled PLCPNumOfValidEntries: 1 fdr8220.1.4.ASC.a > dspbnmif bnmLineInterfaceFormat: bnmSti fdr8220.1.4.ASC.a > dspclksrc PrimaryClockSource: Inband from BNM SecondaryClockSource: Internal Oscillator CurrentClockSource: Primary ClockSwitchState: NoChange ExtClkPresent: Not Present ExtClkSrcImpedance: 75 ohms ExtClkConnectorType: BNC
fdr8220.1.4.ASC.a > dspbnmif bnmLineInterfaceFormat: bnmSti
fdr8220.1.4.ASC.a > dspclksrc PrimaryClockSource: Inband from BNM SecondaryClockSource: Internal Oscillator CurrentClockSource: Primary ClockSwitchState: NoChange ExtClkPresent: Not Present ExtClkSrcImpedance: 75 ohms ExtClkConnectorType: BNC
MC 3810 Router (r3810a)
Command summary:
-
show ver
-
show run
-
show frame pvc
-
show frame map
-
show int se0:1
-
show cont t1 0
-
show cdp nei det
r3810a# ping 1.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 12/17/32 ms r3810a# show ver Cisco Internetwork Operating System Software IOS (tm) MC3810 Software (MC3810-JS-M), Version 12.0(4)T, RELEASE SOFTWARE (fc) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Wed 28-Apr-99 21:19 by kpma Image text-base: 0x00023000, data-base: 0x00AF1324 ROM: System Bootstrap, Version 11.3(1)MA1, MAINTENANCE INTERIM SOFTWARE ROM: MC3810 Software (MC3810-WBOOT-M), Version 11.3(1)MA1, MAINTENANCE INTERIM r3810a uptime is 2 days, 23 hours, 29 minutes System restarted by reload System image file is "flash:mc3810-js-mz.120-4.T.bin" Cisco MC3810 (MPC860) processor (revision 06.07) with 27648K/5120K bytes of mem. Processor board ID 09550018 PPC860 PowerQUICC, partnum 0x0000, version A03(0x0013) Channelized E1, Version 1.0. Bridging software. X.25 software, Version 3.0.0. SuperLAT software copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. Primary Rate ISDN software, Version 1.1. MC3810 SCB board (v05.A0) 1 Multiflex T1(slot 3) RJ45 interface(v01.K0) 1 Six-Slot Analog Voice Module (v03.K0) 1 Analog FXS voice interface (v03.K0) port 1/1 1 3-DSP(slot2) Voice Compression Module(v01.--) 1 Ethernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 2 Serial(sync/async) network interface(s) 1 Channelized E1/PRI port(s) 1 Channelized T1/PRI port(s) 256K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (INTEL28F016) Configuration register is 0x2102
r3810a# show run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname r3810a ! network-clock base-rate 56k ip subnet-zero ! ! ! controller T1 0 framing esf linecode b8zs channel-group 1 timeslots 1-24 speed 64 ! ! ! interface Ethernet0 no ip address no ip directed-broadcast shutdown ! interface Serial0 no ip address no ip directed-broadcast no ip mroute-cache shutdown no fair-queue ! interface Serial1 no ip address no ip directed-broadcast shutdown ! interface Serial0:1 ip address 1.1.1.3 255.255.255.0 no ip directed-broadcast encapsulation frame-relay ip mroute-cache no fair-queue cdp enable frame-relay map ip 1.1.1.1 300 broadcast ! interface Switch0 no ip address no ip directed-broadcast encapsulation frame-relay no fair-queue ! ip classless no ip http server ! ! ! line con 0 transport input none line aux 0 line 2 3 line vty 0 4 login ! ! voice-port 1/1 timeouts call-disconnect 0 ! ! end
r3810a# show frame pvc
PVC Statistics for interface Serial0:1 (Frame Relay DTE)
Active Inactive Deleted Static
Local 1 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0
DLCI = 300, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0:1
input pkts 1538 output pkts 1568 in bytes 1338910
out bytes 1342465 dropped pkts 0 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 14 out bcast bytes 3722
pvc create time 1d01h, last time pvc status changed 00:29:30
PVC Statistics for interface Switch0 (Frame Relay DTE)
r3810a# show frame map Serial0:1 (up): ip 1.1.1.1 dlci 300(0x12C,0x48C0), static, broadcast, CISCO, BW = 153600, status defined, active
r3810a# show int se0:1
Serial0:1 is up, line protocol is up
Hardware is PQUICC Serial
Internet address is 1.1.1.3/24
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY, crc 16, loopback not set
Keepalive set (10 sec)
Scramble enabled
LMI enq sent 9137, LMI stat recvd 9138, LMI upd recvd 8, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 1023 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 14/0, interface broadcasts 0
Last input 00:00:09, output 00:00:09, output hang never
Last clearing of "show interface" counters 1d01h
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
10678 packets input, 1469187 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
10703 packets output, 1460766 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
r3810a# show cont t1 0
T1 0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
Slot 3 CSU Serial #08625843 Model TEB HWVersion 4.70 RX level = -0DB
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
Data in current interval (564 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 2:
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
...................output truncated...............
r3810a# show cdp nei det Device ID: r3810b Entry address(es): IP address: 1.1.1.1 Platform: Cisco MC3810, Capabilities: Router Interface: Serial0:1, Port ID (outgoing port): Serial0:1 Holdtime : 131 sec Version : Cisco Internetwork Operating System Software IOS (tm) MC3810 Software (MC3810-A2BINR3V2-M), Version 12.0(3), RELEASE SOFTWAR) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 08-Feb-99 23:25 by phanguye advertisement version: 1
MGX 8220 IMATM-8T1/B (remfdr)
Command summary:
-
version
-
dsplns
-
dspdsx3lns
-
dspln
-
dspports
-
dspimagrp
-
dspimainfo
-
dspplpp
-
dspimagrpcnt
-
dspimalncnt
-
dspimaln
-
dspclksrc
remfdr.1.8.IMATMB.a > version
***** Cisco Systems, Inc. AXIS IMATM Card *****
Firmware Version = 5.0.12
Backup Boot version = IMA_BT_1.0.02
IMATM Xilinx file = imatm_b_xilinx.h
VxWorks (for Cisco Systems, Inc.) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Thu Jun 22 11:22:38 PDT 2000.
Boot line:
remfdr.1.8.IMATMB.a > dsplns
Line Conn Type Status/Coding Length XmtClock Alarm Stats
Type Source Alarm
---- ----- ------------ ------ -------- ------------- -------- ----- -----
8.1 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LoopTimi No No
8.2 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LoopTimi No No
8.3 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LoopTimi No No
8.4 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LoopTimi No No
8.5 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
8.6 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
8.7 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
8.8 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
LineNumOfValidEntries: 8
remfdr.1.8.IMATMB.a > dspdsx3lns
Line Type Coding Length Criteria AIScBitsCheck
---- -------------- -------- ------------- ----------- -------------
8.1 dsx3CbitParity dsx3B3ZS LessThan225ft 3 out of 8 Ignore C-bits
LineNumOfValidEntries: 1
remfdr.1.8.IMATMB.a > dspln 1
LineNum: 1
LineConnectorType: RJ-48
LineType: dsx1ESF
LineEnable: Enabled
LineCoding: dsx1B8ZS
LineLength: 0-131 ft
LineXmtClockSource: LoopTiming
LineLoopbackCommand: NoLoop
LineSendCode: NoCode
LineUsedTimeslotsBitMap: 0xffffffff
LineLoopbackCodeDetection: codeDetectDisabled
LineBERTEnable: Disable
LineNumOfValidEntries: 8
remfdr.1.8.IMATMB.a > dspports
No ATM T1/E1 UNI ports currently active
List of IMA groups:
===================
ImaGrp PortType Conf Avail Lines configured Lines present Tol Diff Port e
rate rate Delay(ms)
------ -------- ----- ------ --------------- --------------- --------- ------
8.1 UNI 14364 14364 1.2.3.4 1.2.3.4 275 Active
NextPortNumAvailable: 6
remfdr.1.8.IMATMB.a > dspimagrp 1
IMA Group number : 1
Port type : UNI
Lines configured : 1.2.3.4
Enable : Enabled
IMA Port state : Active
IMA Group Ne state : operational
PortSpeed (cells/sec) : 14364
GroupTxAvailCellRate (cells/sec) : 14364
ImaGroupTxFrameLength(cells) : 128
LcpDelayTolerance (IMA frames) : 1
ReadPtrWrPtrDiff (cells) : 4
Minimum number of links : 1
MaxTolerableDiffDelay (msec) : 275
Lines Present : 1.2.3.4
Observed Diff delay (msec) : 0
Clock Mode : CTC
GroupAlpha : 2
GroupBeta : 2
GroupGamma : 1
GroupConfiguration : 1
IMAGrp Failure status : No Failure
Timing reference link : 1
ImaGroupTxImaId : 0x0
ExpectedGroupRxImaId : 0x0
remfdr.1.8.IMATMB.a > dspimainfo
Link Group NeTx NeRx FeTx FeRx TxLID RxID
State State State State
------------------------------------------------------------------
1 1 Active Active Active Active 0 0
2 1 Active Active Active Active 1 1
3 1 Active Active Active Active 2 2
4 1 Active Active Active Active 3 3
remfdr.1.8.IMATMB.a > dspplpp 1
PhysicalPortNumber: 1
CellFraming: ATM
CellScramble: No Scramble
Plpp Loopback: No Loopback
Single-bit error correction: Disabled
remfdr.1.8.IMATMB.a > dspimagrpcnt 1
IMA Group number: 1
Ne Number of failures : 0
remfdr.1.8.IMATMB.a >dspimalncnt 1 1
IMA group number : 1
Line number : 1
Icp Cells Received : 29994
Icp Errored Cells Recvd : 0
Ima Violations Count : 0
Ima OIF anomalies : 0
Ima Ne Severely Errored Seconds : 1
Ima Fe Severely Errored Seconds : 1
Ima Ne Unavailable Seconds : 0
Ima Fe Unavailable Seconds : 0
Ima NeTx Unusable Seconds : 1
Ima NeRx Unusable Seconds : 1
Ima FeTx Unusable Seconds : 0
Ima FeRx Unusable Seconds : 1
Ima FeTx Num. Failues : 0
Ima FeRx Num. Failures : 0
# HEC errored cells : 0
# HEC errored seconds : 0
# Severely HEC errored seconds : 0
remfdr.1.8.IMATMB.a > dspimaln 1 1
IMA Group number : 1
Link number : 1
ImaLink TxLId : 0x0
ImaLink RxLId : 0x0
LinkNeRxState : Active
LinkNeTxState : Active
LinkNeRxFailureStatus : No Failure
LinkFeRxState : Active
LinkFeTxState : Active
LinkFeRxFailureStatus : No Failure
LinkRelDelay : 0
LinkRxTestPattern : 255
Ne Link Tx Num Failures : 0
Ne Link Rx Num Failures : 0
remfdr.1.8.IMATMB.a > dspclksrc
PrimaryClockSource: DS1_LINE1
SecondaryClockSource: BP_8KHZ
CurrentClockSource: PRIMARY
MGX 8220 FRSM-8T1 (remfdr)
Command summary:
-
version
-
dsplns
-
dspln
-
dspports
-
dspchans
-
dspchan
-
tstcon
-
dspchancnt
-
dspportcnt
remfdr.1.11.FRSM.a > version
***** Cisco Systems, Inc. AXIS FRSM-8P Card *****
Firmware Version = 5.0.13
Backup Boot version = FR8_BT_1.0.02
ASCFRSM Xilinx file = cbslave.h
VxWorks (for Cisco Systems, Inc.) version 5.2 Rev B.
Kernel: WIND version 2.4.
Made on Wed Jun 21 16:15:40 PDT 2000.
Boot line:
remfdr.1.11.FRSM.a > dsplns
Line Conn Type Status/Coding Length XmtClock Alarm Stats
Type Source Alarm
---- ----- -------- ------ ------ --------- -------- ----- -----
11.1 RJ-48 dsx1ESF Ena/dsx1B8ZS 0-131 ft LocalTim No No
11.2 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
11.3 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
11.4 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
11.5 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
11.6 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
11.7 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
11.8 RJ-48 dsx1ESF Dis/dsx1B8ZS 0-131 ft LocalTim
LineNumOfValidEntries: 8
remfdr.1.11.FRSM.a > dspln 1
LineNum: 1
LineConnectorType: RJ-48
LineType: dsx1ESF
LineEnable: Enabled
LineCoding: dsx1B8ZS
LineLength: 0-131 ft
LineXmtClockSource: LocalTiming
LineLoopbackCommand: NoLoop
LineSendCode: NoCode
LineUsedTimeslotsBitMap: 0xffffff
LineLoopbackCodeDetection: codeDetectDisabled
LineBertEnable: Disable
LineNumOfValidEntries: 8
remfdr.1.11.FRSM.a > dspports
Port Ena/Speed EQServ SignalType T391 T392 N391 N392 N393 Type AlarI
Ratio
-------- --- ----- ------ ------------ ---- ---- ---- ---- ---- ----- -----
11.1.1 Mod/1536k 1 StrataLMI 10 15 6 3 4 frameRel No f
Number of ports: 1
PortDs0UsedLine1: 0x00ffffff
PortDs0UsedLine2: 0x00000000
PortDs0UsedLine3: 0x00000000
PortDs0UsedLine4: 0x00000000
PortDs0UsedLine5: 0x00000000
PortDs0UsedLine6: 0x00000000
PortDs0UsedLine7: 0x00000000
PortDs0UsedLine8: 0x00000000
PortNumNextAvailable: 100
remfdr.1.11.FRSM.a > dspchans
DLCI Chan EQ I/EQDepth I/EQDEThre I/EECNThre Fst/ DE Type Alarm
------------- ---- -- ----- ----- ----- ----- ----- ----- --- --- ----- -----
11.1.1.100 100 2 65535/65535 32767/32767 6553/6553 Dis/Dis NIW No
Number of channels: 1
ChanNumNextAvailable: 37
remfdr.1.11.FRSM.a > dspchan 100
ChanNum: 100
ChanRowStatus: Mod
ChanPortNum: 1
ChanDLCI: 100
EgressQSelect: 2
IngressQDepth: 65535
IngressQDEThresh: 32767
IngressQECNThresh: 6553
EgressQDepth: 65535
EgressQDEThresh: 32767
EgressQECNThresh: 6553
DETaggingEnable: Disabled
CIR: 1536000
Bc: 5100
Be: 5100
IBS: 100
ForeSightEnable: Disabled
QIR: 4000
MIR: 4000
PIR: 4000
ChanLocalRemoteLpbkState: Disabled
ChanTestType: TestOff
ChanTestState: Passed
ChanRTDresult: 4 ms
ChanType: NIW
ChanFECNmap: setEFCIzero
ChanDEtoCLPmap: mapCLP
ChanCLPtoDEmap: mapDE
ChanFrConnType: PVC
ChanIngrPercentUtil: 100
ChanEgrPercentUtil: 100
ChanEgrSrvRate: 1536000
ChanOvrSubOvrRide: Enabled
ChanNumNextAvailable: 38
remfdr.1.11.FRSM.a > tstcon 100 TestCon in progress. TestCon Passed.
remfdr.1.11.FRSM.a > dspchancnt 100
ChanNum: 100
ChanState: okay
ChanUpTime: 89556
Tx Rx
--------------- ---------------
AbitState: Sending A=1 Off
ATMState: Not sending any state Not receiving any state
Total Frames: 1550 1524
Total Bytes: 1341353 1338801
Frames DE: 173 0
Bytes DE: 174038 0
Frames Discarded: 0 0
Bytes Discarded: 0 0
FramesDiscXceedQDepth: 0 0
BytesDiscXceedQDepth: 0 0
FramesDiscXceedDEThresh: 0 0
Frames FECN: 0 0
Frames BECN: 0 0
FramesTagged FECN: 0 0
FramesTagged BECN: 0 0
KbpsAIR: 0 0
FramesTaggedDE: 173 0
BytesTaggedDE: 174038 0
RcvFramesDiscShelfAlarm: 0
XmtFramesDiscPhyLayerFail: 0
XmtFramesDiscCRCError: 0
XmtFramesDiscReAssmFail: 0
XmtFramesDiscSrcAbort: 0
XmtFramesDuringLMIAlarm: 0
XmtBytesDuringLMIAlarm: 0
RcvFramesDiscUPC: 0
XmtFramesInvalidCPIs: 0
XmtFramesLengthViolations: 0
XmtFramesOversizedSDUs: 0
XmtFramesUnknownProtocols: 0
RcvFramesUnknownProtocols: 0
remfdr.1.11.FRSM.a > dspportcnt 1
PortNum: 1
Tx Rx
--------------- ---------------
Total Frames: 10977 11009
Total Bytes: 1495326 1484340
Frames FECN: 0 0
Frames BECN: 0 0
Frames Abort: 0 1
Buf Not Available: 0 0
KbpsAIR: 0 0
XmtFramesDiscXceedQDepth: 0
XmtBytesDiscXceedQDepth: 0
XmtFramesDuringLMIAlarm: 3
XmtByteDuringLMIAlarm: 45
XmtFramesUnderrun: 0
RcvFramesDE: 0
RcvFramesDiscCRCError: 2
RcvFramesDiscIllegalHeader: 26
RcvFramesDiscAlignmentError: 1
RcvFramesDiscIllegalLen: 0
Tx Rx
--------------- ------
RcvFramesDiscXceedDEThresh: 0
RcvFramesDiscNoChan: 0
RcvFramesUnknownDLCI: 0
RcvLastUnknownDLCI: 0
RcvFramesTaggedFECN: 0
RcvFramesTaggedBECN: 0
RcvFramesTaggedDE: 0
Status: 9427 0
StatusInquiry: 0 9427
AsynchUpdate: 0 0
RcvInvalidRequest: 0
RcvUNISeqMismatch: 1
RcvNNISeqMismatch: 0
UNISignallingTimeout: 17
NNISignallingTimeout: 0
FramesCLLM: 0 0
BytesCLLM: 0 0
CLLMFailures: 0
MGX 8220 ASC - Remote Feeder (remfdr)
Command summary:
-
version
-
dsplns
-
dspcds
-
xdspln
-
dspbnmif
-
dspclksrc
remfdr.1.3.ASC.a > version
version
***** Cisco Systems, Inc. AXIS ASC Card *****2
Firmware Version = 5.0.14
Backup Boot version = ASC_BT_1.0.03
ASCFRSM Xilinx file = asc025.h
ASC2 Xilinx file = ASC2_Xilinx.h
ASCBNM Xilinx file = A:bnm_a E:bnm_e
ASCBNM Altera file = bnm155_2
SRM-T1E1 Xilinx file = A:srm038.h, E:srmE038.h
SRM-3T3 Xilinx file = srm038.h
SRM-3T3 Encoder file = encoder42_004.ttf
SRM-3T3 Encoder-2 file = encoder80_001.ttf
SRM-3T3 Decoder file = decoder42_004.ttf
SRM-3T3 Clock file = clkctrl_40.ttf
SRM-3T3 I-Cube file = ic320.h
VxWorks (for Cisco Systems, Inc.) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Wed Jun 21 15:53:33 PDT 2000.
Boot line:
ln(0,0)
remfdr.1.3.ASC.a > dsplns Line Type Coding Length Criteria AIScBitsCheck ---- -------------- -------- ------------- ----------- ------------- 1.1 dsx3CbitParity dsx3B3ZS LessThan225ft 3 out of 8 Check C-bits LineNumOfValidEntries: 1
remfdr.1.3.ASC.a > dspcds
Slot CardState CardType CardAlarm Redundancy
---- ----------- ------------ --------- ------------------
1.1 Active BNM-T3 Minor
1.2 Unknown
1.3 Active ASC
1.4 Empty
1.5 Active CESM-4T1
1.6 Empty
1.7 Active FRSM-4T1
1.8 Active IMA-8T1/B
1.9 Active FRSM-8T1
1.10 Active CESM-4T1
1.11 Active FRSM-8T1
1.12 Empty
1.13 Empty
1.14 Empty
1.15 Active SRM-3T3
1.16 Empty
NumOfValidEntries: 16
NodeName: remfdr
Date: 11/01/2000
Time: 14:20:07
TimeZone: PST
TimeZoneGMTOff: -8
StatsMasterIpAddress: 0.0.0.0
shelfIntegratedAlarm: Minor
BkplnSerialNum: 142586
BkplnType: 1
BkplnFabNumber: 218412-00
BkplnHwRev: bb
remfdr.1.3.ASC.a > xdspln -plcp 1 PLCP CellFraming PayloadScramble ---- ----------- --------------- 1.1 PLCP Disabled PLCPNumOfValidEntries: 1
remfdr.1.3.ASC.a > dspbnmif bnmLineInterfaceFormat: bnmUni
remfdr.1.3.ASC.a > dspclksrc
PrimaryClockSource: Inband from BNM
SecondaryClockSource: Inband from BNM
CurrentClockSource: Inband from BNM
ClockSwitchState: SrcChanged
ExtClkPresent: Not Present
ExtClkSrcImpedance: 75 ohms
ExtClkConnectorType: BNC
MC 3810 Router (r3810b)
Command summary:
-
show ver —
-
show run
-
show frame pvc
-
show frame map
-
show int s0:1
-
show cont t1 0
-
show cdp nei det
-
debug frame-relay lmi
r3810b# ping 1.1.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 12/20/40 ms r3810b# show ver Cisco Internetwork Operating System Software IOS (tm) MC3810 Software (MC3810-A2BINR3V2-M), Version 12.0(3), RELEASE SOFTWAR) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 08-Feb-99 23:25 by phanguye Image text-base: 0x00023000, data-base: 0x00761120 ROM: System Bootstrap, Version 11.3(1)MA1, MAINTENANCE INTERIM SOFTWARE ROM: MC3810 Software (MC3810-WBOOT-M), Version 11.3(1)MA1, MAINTENANCE INTERIM r3810b uptime is 6 days, 22 hours, 51 minutes System restarted by power-on System image file is "flash:mc3810-a2binr3v2-mz.120-3" Cisco MC3810 (MPC860) processor (revision 06.07) with 27648K/5120K bytes of mem. Processor board ID 13001719 PPC860 PowerQUICC, partnum 0x0000, version A03(0x0013) Bridging software. MC3810 SCB board (v05.A1) 1 Multiflex T1(slot 3) RJ45 interface(v02.C0) 1 Multiflex T1(slot 4) RJ45 interface(v02.C0) 1 6-DSP(slot2) Voice Compression Module(v02.A0) 1 6-DSP(slot5) Voice Compression Module(v02.A0) 1 Ethernet/IEEE 802.3 interface(s) 4 Serial network interface(s) 2 Channelized T1/PRI port(s) 256K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (AMD29F016) Configuration register is 0x2102
r3810b# show run Current configuration: ! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname r3810b ! ip subnet-zero ! ! controller T1 0 framing esf linecode b8zs channel-group 1 timeslots 1-24 speed 64 ! controller T1 1 ! ! interface Ethernet0 no ip address no ip directed-broadcast shutdown ! interface Serial0 no ip address no ip directed-broadcast shutdown ! interface Serial1 no ip address no ip directed-broadcast shutdown ! interface Serial0:1 ip address 1.1.1.1 255.255.255.0 no ip directed-broadcast encapsulation frame-relay ip mroute-cache no fair-queue frame-relay map ip 1.1.1.3 100 broadcast ! interface FR-ATM20 no ip address no ip directed-broadcast shutdown ! ip classless ! ! line con 0 transport input none line aux 0 line vty 0 4 exec-timeout 0 0 login ! ! end
r3810b# show fr pvc PVC Statistics for interface Serial0:1 (Frame Relay DTE) DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0:1 input pkts 1544 output pkts 1519 in bytes 1336729 out bytes 1335307 dropped pkts 10 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 173 out DE pkts 0 out bcast pkts 0 out bcast bytes 0 pvc create time 1d01h, last time pvc status changed 00:17:24
r3810b# show fr map Serial0:1 (up): ip 1.1.1.3 dlci 100(0x64,0x1840), static,broadcast, CISCO, BW = 1536000, status defined, active
r3810b# show int s0:1
Serial0:1 is up, line protocol is up
Hardware is PQUICC Serial
Internet address is 1.1.1.1/24
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation FRAME-RELAY, crc 16, loopback not set, keepalive set (10 sec)
LMI enq sent 9088, LMI stat recvd 9088, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 1023 LMI type is CISCO frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0
Last input 00:00:08, output 00:00:09, output hang never
Last clearing of "show interface" counters 1d02h
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
11056 packets input, 1473959 bytes, 0 no buffer
Received 9502 broadcasts, 0 runts, 0 giants, 0 throttles
2 input errors, 1 CRC, 1 frame, 0 overrun, 0 ignored, 0 abort
11093 packets output, 1464429 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
r3810b# show contr t1 0
T1 0 is up.
No alarms detected.
Slot 3 CSU Serial #14768626 Model TEB HWVersion 6.00
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
Data in current interval (732 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
177 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
177 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
0 Line Code Violations, 0 Path Code Violations
211 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
211 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 2:
0 Line Code Violations, 0 Path Code Violations
192 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
192 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 3:
0 Line Code Violations, 0 Path Code Violations
187 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
187 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 4:
0 Line Code Violations, 0 Path Code Violations
186 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
186 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 5:
0 Line Code Violations, 0 Path Code Violations
187 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
............................output truncated.............................
r3810b# show cdp nei deta
Device ID: r3810a
Entry address(es):
IP address: 1.1.1.3
Platform: Cisco MC3810, Capabilities: Router
Interface: Serial0:1, Port ID (outgoing port): Serial0:1
Holdtime : 156 sec
Version :
Cisco Internetwork Operating System Software
IOS (tm) MC3810 Software (MC3810-JS-M), Version 12.0(4)T, RELEASE SOFTWARE (fc)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Wed 28-Apr-99 21:19 by kpma
Note: Because the debug commands generate a significant amount of output, use them only when traffic on the IP network is low, so other activity on the system is not adversely affected.Before attempting any debug commands, see Important Information on Debug Commands.
r3810b# debug frame-relay lmi Frame Relay LMI debugging is on Displaying all Frame Relay LMI data r3810# 6d22h: Serial0:1(out): StEnq, myseq 167, yourseen 177, DTE up 6d22h: datagramstart = 0x1BC2EF8, datagramsize = 13 6d22h: FR encap = 0xFCF10309 6d22h: 00 75 01 01 01 03 02 A7 B1 6d22h: 6d22h: Serial0:1(in): Status, myseq 167 6d22h: RT IE 1, length 1, type 1 6d22h: KA IE 3, length 2, yourseq 178, myseq 167 6d22h: Serial0:1(out): StEnq, myseq 168, yourseen 178, DTE up 6d22h: datagramstart = 0x1BC2EF8, datagramsize = 13 6d22h: FR encap = 0xFCF10309 6d22h: 00 75 01 01 01 03 02 A8 B2 6d22h: 6d22h: Serial0:1(in): Status, myseq 168 6d22h: RT IE 1, length 1, type 1 6d22h: KA IE 3, length 2, yourseq 179, myseq 168
r3810b#und all All possible debugging has been turned off
BPX 8600
Command summary:
-
dspcds
-
dspnode
-
dsptrks
-
dsptrkcnf
-
dspcons
-
dspcon
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:46 PST FrontCard BackCard FrontCard BackCard Type Rev Type Rev Status Type Rev Type Rev Status 1 Empty 9 BXM-155 CDB MM-4 BA Standby 2 BNI-T3 CJM T3-3 BE Active 10 BXM-155 EJB MM-4 BA Standby 3 BNI155E DJR Empty Standby 11 BNI155E DJR MMF-2 AC Standby 4 Empty 12 BXM-E3 BDY MMF-2 AC Mismatch 5 Empty 13 BXM-T3 BDY TE3-12BA Active 6 ASI-T3 CDF T3-2 BE Standby-T 14 Empty 7 BCC-3 CLM LM-2 AC Standby 15 ASM ACC LMASM AC Active 8 BCC-3 CLM LM-2 AC Active Last Command: dspcds |
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:48 PST
BPX 8620 Interface Shelf Information
Trunk Name Type Part Id Ctrl Id Control_VC Alarm
VPI VCIRange
2.1 fdr8220 AXIS - - - - MIN
13.1 remfdr AXIS - - - - MIN
Last Command: dspnode
|
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:42 PST
TRK Type Current Line Alarm Status Other End
2.1 T3 Clear - OK fdr8220(AXIS)
13.1 T3 Clear - OK remfdr(AXIS)
Last Command: dsptrks
|
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:43 PST
TRK 2.1 Config T3 [96000 cps] BNI-T3 slot: 2
Transmit Rate: 96000 VPC Conns disabled: --
Protocol By The Card: -- Line framing: PLCP
VC Shaping: -- coding: --
Hdr Type NNI: -- recv impedance: --
Statistical Reserve: 1000 cps cable type:
Idle code: 7F hex length: 0-225 ft.
Connection Channels: 2027 Pass sync: No
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR Loop clock: No
SVC Vpi Min: -- HCS Masking: Yes
SVC Channels: -- Payload Scramble: No
SVC Bandwidth: -- cps Frame Scramble: --
Restrict CC traffic: No Virtual Trunk Type: --
Link type: Terrestrial Virtual Trunk VPI: --
Routing Cost: 10 Deroute delay time: 0 seconds
Last Command: dsptrkcnf 2.1
|
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:39 PST Local Remote Remote Route Channel NodeName Channel State Type Avoid COS O 2.1.9.300 bpx8600 13.1.11.100 Ok atfr 13.1.11.100 bpx8600 2.1.9.300 Ok atfr Last Command: dspcons |
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:41 PST
Conn: 2.1.9.300 bpx8600 13.1.11.100 atfr Status:OK
PCR(0+1) % Util CDVT(0+1) FBTC SCR MBS PLC
3000/3000 100/100 25000/25000 y 3000/3000 1000/1000 3
Path: Route information not applicable for local connections
bpx8600 BNI-T3 : OK bpx8600 BXM : OK
Line 2.1 : OK Line 13.1 : OK
OAM Cell RX: Clear NNI : OK
NNI : OK
bpx8600 TRM StrataCom BPX 8620 9.2.34 Oct. 31 2000 23:41 PST
Conn: 2.1.9.300 bpx8600 13.1.11.100 atfr Status:OK
PCR(0+1) % Util CDVT(0+1) SCR MBS
3000/3000 100/100 25000/25000 3000/3000 1000/1000
Policing VC Qdepth EFCI IBS
3 1280/1280 35/35 1/1
Last Command: dspcon 2.1.9.300
|
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
NetPro Discussion Forums - Featured Conversations
| NetPro Discussion Forums - Featured Conversations for WAN Switching |
| Network Infrastructure: WAN Routing and Switching |
Related Information
- Connecting an MGX 8220 AUSM-8T1/B to a 3620 Using IMA Trunks Sample Configuration
- AUSM/B IMA Troubleshooting Guide
- MGX 8220 Release 5.0 Documentation
- Cisco WAN Switching Solutions - Cisco Documentation
- Guide to New Names and Colors for WAN Switching Products
- Downloads - WAN Switching Software ( registered customers only)
- Technical Support - Cisco Systems
| Updated: Apr 30, 2009 | Document ID: 22977 |