Installation and Configuration, Release 5 - Specifications

T3 line interface connector:	BNC connector per ANSI T1.404
T3 cable recommended:	Coax, 75 ohm, 728A or equivalent
T3 line signal:	DSX-3 Specification per ANSI T1.102 and ATT PUB 54014
T3 line rate:	44.736 Mbps ± 895 bps
T3 framing:	Asynch. C-bit Parity per ANSI T1.107a
Input jitter tolerance:	Per ATT TR 54014, Category II Equipment
Output jitter generation:	Per ATT TR 54014, Table B1, "Equipment with DS3 Oscillator" Category
PMD layer alarms:	LOS, OOF, AIS, RAI
PMD layer performance statistics:	LCV, LES, % EFS, LSES, SEFS, PCV, PES, PSES, SEFS, UAS
Trans. convergence protocol:	PLCP per TR-TSV-000773
TC layer alarms:	OOF, RAI
TC layer performance statistics:	BIP8-CV, BIP8-ES, BIP8-SES, SEFS, UAS
ATM layer protocol:	Header check sum is XORed with the COSET function (0 x 55) per CCITT I.361
ATM layer counters:	Number of cells received good Number of cells received and discarded due to bad HEC Number of cells transmitted good Number of cells received from cell bus Number of cells transmitted to cell bus
Diagnostics:	Header of first cell received with invalid egress translation entries Number of cells dropped due to invalid egress translation entries

Card General

Synchronization:	Derives 8-kHz shelf synchronization clock from a variety of sources: Internal 8-kHz clock (10 ppm) BNM-T3 PLCP External T1/E1 clock port with a clock rate of 1.544 Mbps ± 50 bps (T1) or 2.048 Mbps ± 100 bps (E1)
External Office clock interface:	DB-15 connector using LM-T3/E3-D (T1/E1 clock) BNC connector using LM-T3/E3-B (E1 clock) Alarm interface: CO compatible alarm indicator and control DB-15 connector
Indicators:	Per card: active (green), failed (red), standby (yellow) T3 Interface: active and okay (green) Active and local alarm (red) Active and remote alarm (yellow) Minor DS-3 statistical alarm
Maintenance/Serviceability Features:	Internal isolation loopbacks External remote loopback Hot-pluggable
Reliability:	> 65000 hours MTBF
Card Size:	BNM-T3: 7.25 in. x 16.25 in. LM-T3E3-D: 7.25 in. x 4.5 in. LM-T3E3-B: 7.25 in. x 4.5 in.
Power:	-48V DC, 25W

BNM-E3 Specification

Intershelf Link

E3 Line Interface Connector:	BNC connector per ANSI T1.404
E3 Cable Recommended:	Coax, 75 ohm, 728A or equivalent
E3 Line Signal:	Per G.703
E3 Line Rate:	34.368 Mbps ± 20 PPM
E3 Framing:	G.832 and G.804
Input Jitter Tolerance:	Per G.703
Output Jitter Generation:	Per G.703
PMD Layer Alarms:	LOS, OOF, AIS, RAI
PMD Layer Performance Statistics:	LCV, LES, %EFS, LSES, SEFS, PCV, PES, PSES, SEFS, UAS
Trans. Convergence Protocol:	PLCP per TR-TSV-000773
TC Layer Alarms:	OOF, RAI
TC Layer Performance Statistics:	BIP8-CV, BIP8-ES, BIP8-SES, SEFS, UAS
ATM Layer Protocol:	Header check sum is XORed with the COSET function (0x55) per CCITT I.361
ATM Layer Counters:	Number of cells received good Number of cells received and discarded due to bad HEC Number of cells transmitted good Number of cells received from cell bus Number of cells transmitted to cell bus
Diagnostics:	Header of first cell received with invalid egress translation entries Number of cells dropped due to invalid egress translation entries Number of unacknowledged cells transmitted to cell bus

Card General

Synchronization:	Derives 8-kHz shelf synchronization clock from a variety of sources: E3 physical interface External T1/E1 clock port with a clock rate of 1.544 Mbps ± 50 bps (T1) or 2.048 Mbps ± 100 bps (E1)
External Office clock interface:	DB15 connector using LM-T3/E3-D (T1/E1 clock) BNC connector using LM-T3/E3-B (E1 clock)
Alarm interface:	CO compatible alarm indicator and controls DB-15 connector
Indicators:
Per Card:	Active (green), failed (red), standby (yellow)
E3 Interface:	Active and okay (green) Active and local alarm (red) Active and remote alarm (yellow) Minor DS-3 statistical alarm
Shelf Voltage:	Voltage okay (green) B voltage okay (green)
Alarms:	Major (red), minor (yellow) ACO (yellow), history (green)
Maintenance/Serviceability Features:	Internal isolation loopbacks External remote loopback Hot-pluggable
Card Size:	BNM-T3: 7.25 in. x 16.25 in. LM-T3E3-D: 7.25 in. x 4.5 in. LM-T3E3-B: 7.25 in. x 4.5 in.
Power:	-48V DC, 25W

BNM-155 Specifications

Intershelf Link Specifications

Common Specifications

Framing:	SONET STS-3c per ANSI T1.105
PMD Layer Alarms:	Loss of signal (LOS) Severely errored framing (SEF) Loss of frame (LOF) Line alarm indication signal (AIS-L) STS path alarm indication signal (AIS-P) Line remote defect indication (RDI-L) Loss of pointer (LOP) STS path remote defect indication (RDI-P)
Transmission Convergence Protocol:	Per GR-253-CORE and ANSI T1.105
TC Layer Alarm:	Loss of cell delineation (LCD)
ATM Layer Protocol:	Header check sum is XORed with the COSET function (0 x 55) per CCITT I.361
ATM Layer Counters:	Number of cells received good Number of cells received and discarded due to bad HEC Number of cells transmitted good
Diagnostics:	Number of cells received from cell bus Number of cells transmitted to cell bus Number of unacknowledged cells transmitted to cell bus Header of first cell received with invalid egress translation errors Number of cells dropped due to invalid ingress translation errors Number of cells dropped due to invalid egress translation entries

SMF Specific Specifications

SMF Line Interface Connector:	SC connectors
Fiber Recommendation:	Single-mode
Maximum Fiber Length:	20 km
SMF Line Signal:	Optical, SONET OC-3c per ANSI T1.105 and GR-253-CORE
SMF Line Rate:	155.52 Mbps
Input Jitter Tolerance:	Per Gr-253-CORE
Output Jitter Generation:	Per Gr-253-CORE

General Card Specifications

Synchronization:	Derives 8 kHz shelf synchronization clock from a variety of sources: Internal 8 kHz (±10 ppm) BNM-155 PLCP External T1/E1 clock port with a clock rate of 1.544 MHz ±50 ppm (T1) or 2.048 MHz ± 100 bps (E1)
External Clock Interface:	DB-15 connector or BNC connector (both are available)
Alarm Interface:	CO compatible alarm indicator and controls via DB-15 connector
Indicators:	Ten LEDs
Per Card	Active (green) Failed (red) Standby (amber)
OC-3 Interface	Single multihue LED Active and okay (green) Active and local alarm (red) Active and remote alarm (amber)
Shelf Voltage	A voltage okay (green) B voltage okay (green)
Alarms	Major (red) Minor (amber) ACO (amber) History (green)
Maintenance Serviceablity Features:	Internal isolation loopbacks External remote loopbacks Hot-pluggable
Reliability	> 65000 hours MTBF
Card Size	BNM-155: 7.25 in. x 16.25 in. SMF-155-LM: 7.25 in. x 4.5 in. UTP-155-LM: 7.25 in. x 4.5 in.
Power	-48V DC, 25W

ASC Specification

802.3 LAN Interface Connector:	AUI interface using DB-15 connector control port: DB-25 RS232 connector; Asynch interface, 99200 baud, 1 start, 1 stop, no parity
Troubleshooting Interface:	Maintenance port: DB-25 RS232 connector; Asynch interface, 9600 baud, 1 start, 1 stop, no parity
Indicators:	Per card: active (green), failed (red), standby (yellow) LAN activity/flashing green
Maintenance/ Serviceability Features:	RS232 maintenance/debug port Internal isolation loopbacks Hot-pluggable
Reliability:	> 65000 hours MTBF
Card Size:	ASC: 7.25 in. x 16.25 in. LM_ASC: 7.0 in. x 4.5 in.
Power:	-48V DC, 25W

SRM-T1/E1 Specification

T1/E1 Line Interface Connector:	BNC-3T# Standby SM requires a special line module: R-DB15-4T1 if active cards use DB15-4T1 R-DB15-4E1 if active cards use DB15-4E1 R-BNC-4E1 if active cards use BNC R-RJ48-8T1 if active cards use RJ-48-8T1 R-RJ48-8E1 if active cards use RJ-48-8E1 R-SNB-4E1 if active cards use SMB-8E1
Line Rate:	T1: 1.544 Mbps ±75 bps (50 ppm) E1: 2.048 Mbps ± 100 bps (50 ppm)
Transmit Clocking:	Normal or looped timed
Input Jitter Tolerance:	Per AT&T Accunet T1.5 Service 1990 - T1 Per G.703 - E1
Physical Layer Alarms:	Indicated in service modules
Physical Layer Performance Statistics:	N/A
Indicators:
Per Card:	Active (green), failed (red), standby (yellow)
BERT:	Active (green), errors (yellow)
1 to N Redundancy:	Active (green)
Indicator for each T3:	Active (green)
Maintenance/Serviceability Features:	DS1 Loopback toward service modules Hot pluggable
Reliability:	>85000 hous MTBF
Card Size:	Front card: 7.25 in. x 16.25 in. Back card: 7 in. x 4.5 in.
Power:	48V DC, 50 W
Loopback codes:	Fractional T1 in-band loopback - ANSI T1/E1-2/92-003 R3 DS0 loopback - TA-TSY-000055 TA-TSY-000057 TA-TSY-0000476
Monitoring trouble codes:	TA-TSY-000077 TA-TSY-0000280 ATT TR-62310

FRSM-4T1 Specification

Service Interface

Line Interface connector:	DB-15—when used with LM-DB15-4T1 line module
Line Rate:	1.544 Mbps ± 50 bps
Line Framing:	ESF per ATT TR 54016
Synchronization:	Transmitter can be either loop-timed to receiver or synchronized to shelf (called normal mode)
Input Jitter Tolerance:	Per ATT TR 62411
Output Jitter Generation:	Per ATT TR 62411 using normal mode synchronization
Physical Layer Alarms:	LOS, OOF, AIS, RAI
Number of Frame Relay Ports:	1-Single Frame Relay stream occupying n consecutive time slots
Frame Relay Interface Rates:	Either 56 kbps or n* 64 kbps; n as defined previously
Frame Relay Interface:	Per ANSI T1.618, 2-octet header
Frame Relay Performance Counters (per port; n x DS0):	Receive frames discarded due to Aborts Receive frames discarded due to illegal header (EA bits)(S) Receive frames discarded due to CRC errors (S) Receive frames discarded due to alignment errors (S) Receive frames discarded due to unknown DLCI (S) Receive frames discarded due to illegal frame length (S) Receive frames discarded due to DE threshold exceeded Receive frames with DE already set Receive frames with FECN already set Receive frames with BECN already set Receive frames tagged FECN Receive frames (S) Receive bytes (S) Transmit frames discarded due to underrun Transmit frames discarded due to Abort Transmit frames discarded due to egress Q-depth exceeded (S) Transmit bytes discarded due to egress Q-depth exceeded (S) Transmit frames discarded due to egress DE threshold exceeded Transmit frames (S)
	Transmit bytes (S) Transmit Frames with FECN set (S) Transmit Frames with BECN set (S)
	LMI receive status inquiry request count (S) LMI transmit status inquiry request count LMI invalid receive status count (S) LMI signaling protocol (keep alive time-out count) (S) LMI sequence number error count (S) LMI receive status transmit count (in response to request) LMI transmit status transmit count (in response to request) Transmit frames during LMI alarm (S) Transmit bytes during LMI alarm (S) LMI update status transmit count (in response to configuration changes)
Diagnostics (per port):	Last unknown DLCI received

System Interface

ATM Layer:	Per CCITT I.361 and ATM UNI v3.1
AAL Layer:	AAL5 per Draft CCITT I.363
FR-Cell Interworking:	Per Draft CCITT I.555 and I.36x.1, as summarized in Frame Relay Forum, FR/ATM PVC Interworking Implementation Agreement FRF.5

Virtual Circuits

Channels (Endpoints):	256 per card—can be allocated across any of the Frame Relay interfaces
Counters:
Service Counters:	Number of frames received (S) Number of bytes received (S) Number of frames received with DE already set (S) Number of bytes received with DE already set (S) Number of frames received with unknown DLCI Number of frames received but discarded (S) Number of received bytes discarded (S) Number of received bytes discarded due to exceeded Q-depth (S) Number of frames received and discarded due to intershelf alarm exceeded DE threshold exceeded Q depth Number of frames received with FECN set Number of frames received with BECN set Number of frames received tagged FECN Number of frames received tagged BECN
	Number of frames transmitted (S) Number of bytes transmitted (S)
	Number of frames transmitted with DE set Number of frames discarded due to reassembly error (S) Number of frames transmitted during LMI logical port alarm Number of frames transmitted with FECN set Number of frames transmitted with BECN set Number of transmit frames discarded Number of transmit bytes discarded Number of transmit frames discarded due to: CRC error (S) egress Q depth exceeded egress DE threshold exceeded source abort physical link failure (T1) ATM cells—Number of cells transmitted to BNM Number of cells transmitted with CLP bit set Number of OAM AIS cells transmitted Number of OAM FERF cells transmitted Number of BCM cells transmitted Number of OAM end-end loopback cells transmitted Number of OAM segment loopback cells transmitted Number of cells received from BNM Number of cells received with CLP bit set Number of OAM AIS cells received Number of OAM FERF cells received Number of BCM cells received Number of OAM end-end loopback cells received Number of OAM segment loopback cells received Number of OAM cells discarded due to CRC-10 error (S)
Statistics:	All previous counters followed by an (S) can be configured as statistics
Diagnostics:	Last unknown LCN received cells with unknown LCN count

Card General

Indicators:
Per Card:	Active (green), standby (yellow), fail (red)
Lines (one per):	Active and okay (green) Active and local alarm (red) Active and remote alarm (yellow)
Maintenance/Serviceability Features:	Internal problem isolation loopbacks hot-pluggable
Reliability:	> 65000 hours MTBF
Card Size:	FRSM-4T1: 7.25 in. x 16.25in. LM-DB15-4T1: 7.0 in. x 4.5 in. Power: -48V DC, 30W (4 T1s)

FRSM-4E1 Specification

Service Interface

Line Interface connector:	DB-15 when used with LM-DB15-4E1 line module BNC when used with LM-BNC-4E1 line module
Line Rate:	2.048 Mbps ± 100 bps
Synchronization:	Transmitter can be either loop-timed to receiver or synchronized to shelf (called normal mode)
Input Jitter Tolerance:	Per G.703
Output Jitter Generation:	Per G.703
Physical Layer Alarms:	LOS, OOF, AIS, RAI
Number of Frame Interfaces:	I to 31 occupying n where 1 < n < 31. Sum of all < 31 for CCS. 1-30 for CAS
Frame Relay Interface Rates:	Either 56 kbps or n* 64 kbps; n as defined previously
Frame Relay Interface:	Per ANSI T1.618, 2-octet header
Frame Relay Performance Counters (per port; n x DS0):	Receive frames discarded due to aborts Receive frames discarded due to illegal header (EA bit)(S) Receive frames discarded due to CRC errors (S) Receive frames discarded due to alignment errors (S) Receive frames discarded due to unknown DLCI (S) Receive frames discarded due to illegal frame length (S) Receive frames discarded due to DE threshold exceeded Receive frames with DE already set Receive frames with FECN already set Receive frames with BECN already set Receive frames tagged FECN Receive frames (S) Receive bytes (S)
	Transmit frames discarded due to underrun Transmit frames discarded due to Abort Transmit frames discarded due to egress Q-depth exceeded (S) Transmit bytes discarded due to egress Q-depth exceeded (S) Transmit frames discarded due to egress DE threshold exceeded Transmit frames (S) Transmit bytes(S) Transmit Frames with FECN set (S) Transmit Frames with BECN set (S) LMI receive status inquiry request count (S) LMI transmit status inquiry request count LMI invalid receive status count (S) LMI signaling protocol (keep alive time-out count) (S) LMI sequence number error count (S) LMI receive status transmit count (in response to request) LMI transmit status transmit count (in response to request) Transmit frames during LMI alarm (S) Transmit bytes during LMI alarm (S) LMI update status transmit count (in response to configuration changes)
Diagnostics (per port):	Last unknown DLCI received

System Interface

ATM Layer:	Per CCITT I.361 and ATM UNI v3.1
AAL Layer:	AAL5 per Draft CCITT I.363
FR-Cell Interworking:	Per Draft CCITT I.555 and I.36x.1, as summarized in Frame Relay Forum, FR/ATM PVC Interworking Implementation Agreement FERF.5

Virtual Circuits

Channels (Endpoints):	256 per card—can be allocated across any of the Frame Relay interfaces
Counters:	Service counters: Number of frames received (S) Number of bytes received (S) Number of frames received with DE already set (S) Number of bytes received with DE already set (S) Number of frames received with unknown DLCI Number of frames received but discarded (S) Number of received bytes discarded (S) Number of received bytes discarded due to exceeded Q-Depth (S) Number of frames received and discarded due to intershelf alarm exceeded DE threshold (S) exceeded Q depth (S) Number of frames received with FECN set Number of frames received with BECN set
	Number of frames received tagged FECN Number of frames received tagged BECN Number of frames transmitted (S) Number of bytes transmitted (S) Number of frames transmitted with DE set (S) Number of frames discarded due to reassembly errors (S) Number of frames transmitted during LMI logical port alarm (S) Number of frames transmitted with FECN set (S) Number of frames transmitted with BECN set (S) Number of transmit frames discarded (S) Number of transmit bytes discarded Number of transmit frames discarded due to: CRC error (S) egress Q depth exceeded (S) egress DE threshold exceeded source abort physical link failure (T1)
	ATM cells: Number of cells transmitted to BNM Number of cells transmitted with CLP bit set Number of OAM AIS cells transmitted (S) Number of OAM FERF cells transmitted (S) Number of BCM cells transmitted Number of OAM end-end loopback cells transmitted (S) Number of OAM segment loopback cells transmitted Number of cells received from BNM Number of cells received with CLP bit set Number of OAM AIS cells received (S) Number of OAM FERF cells received (S) Number of BCM cells received Number of OAM end-end loopback cells received (S) Number of OAM segment loopback cells received Number of OAM cells discarded due to CRC-10 error (S)
Statistics:	All previous counters followed by an (S) can be configured as statistics.
Diagnostics:	8 Last unknown LCN received Cells with unknown LCN count Card general
Indicators:	Per card: Active (green), standby (yellow), fail (red) Lines (one per): Active and okay (green) Active and local alarm (red), Active and remote alarm (yellow)
Maintenance/Serviceability Features:	Internal problem isolation loopbacks Hot-pluggable
Card Size:	FRSM-4E1: 7.25 in. x 16.25 in. LM-DB15-4E1: 7.0 in. x 4.5 in. LM-BNC-4E1: 7.0 in x 4.5 in.
Power:	-48V DC, 30W (4 E1s)
Ingress:	8000 cell buffer shared between virtual channels/paths Standard usage parameter control (UPC) Selective cell discard Virtual circuit queuing EFCI setting per VC
Egress:	8000 cell storage capacity shared between four ports Up to 12-user-selectable egress queues per port Selective cell discard EFCI setting per queue

FRSM-8T1 Specification

Service Interface

Line Interface connector:	RJ-48 when used with LM-RJ-48-8T1 line module
Line Rate:	1.544 Mbps ± 50 bps
Line Framing:	ESF per ATT TR 54016
Synchronization:	Transmitter can be either loop-timed to receiver or synchronized to shelf (called normal mode)
Input Jitter Tolerance:	Per ATT TR 62411
Output Jitter Generation:	Per ATT TR 62411 using normal mode synchronization
Physical Layer Alarms:	LOS, OOF, AIS, RAI
Number of Frame Relay Ports:	1-Single Frame Relay stream occupying n consecutive time slots
Frame Relay Interface Rates:	Either 56 kbps or n * 64 kbps; n as defined previously
Frame Relay Interface:	Per ANSI T1.618, 2-octet header
Frame Relay Performance Counters (per port; n x DS0):	Receive frames discarded due to aborts Receive frames discarded due to illegal header (EA bit) (S) Receive frames discarded due to CRC errors (S) Receive frames discarded due to alignment errors (S) Receive frames discarded due to unknown DLCI (S) Receive frames discarded due to illegal frame length (S) Receive frames discarded due to DE threshold exceeded Receive frames with DE already set Receive frames with FECN already set Receive frames with BECN already set Receive frames tagged FECN Receive frames (S) Receive bytes (S) Transmit frames discarded due to underrun Transmit frames discarded due to abort Transmit frames discarded due to egress Q-depth exceeded (S) Transmit bytes discarded due to egress Q-depth exceeded (S) Transmit frames discarded due to egress DE threshold exceeded transmit frames (S)
	Transmit bytes (S) Transmit frames with FECN set (S) Transmit frames with BECN set (S)
	LMI receive status inquiry request count (S) LMI transmit status inquiry request count LMI invalid receive status count (S) LMI signaling protocol (keep alive time-out count) (S) LMI sequence number error count (S) LMI receive status transmit count (in response to request) LMI transmit status transmit count (in response to request) Transmit frames during LMI alarm (S) Transmit bytes during LMI alarm (S) LMI update status transmit count (in response to configuration changes)
Diagnostics (per port):	Last unknown DLCI received

System Interface

ATM Layer:	Per CCITT I.361 and ATM UNI v3.1
AAL Layer:	AAL5 per draft CCITT I.363
FR-Cell Interworking:	Per draft CCITT I.555 and I.36x.1, as summarized in Frame Relay Forum, FR/ATM PVC Interworking Implementation Agreement FRF.5

Virtual Circuits

Channels (Endpoints):	256 per card—can be allocated across any of the Frame Relay interfaces
Counters:
Service Counters:	Number of frames received (S) Number of bytes received (S) Number of frames received with DE already set (S) Number of bytes received with DE already set (S) Number of frames received with unknown DLCI Number of frames received but discarded (S) Number of received bytes discarded (S) Number of received bytes discarded due to exceeded Q-depth (S) Number of frames received and discarded due to intershelf alarm exceeded DE threshold (S) exceeded Q depth (S) Number of frames received with FECN set Number of frames received with BECN set Number of frames received tagged FECN Number of frames received tagged BECN
	Number of frames transmitted (S) Number of bytes transmitted (S)
	Number of frames transmitted with DE set (S) Number of frames discarded due to reassembly errors (S) Number of frames transmitted during LMI logical port alarm (S) Number of frames transmitted with FECN set (S) Number of frames transmitted with BECN set (S) Number of transmit frames discarded (S) Number of transmit bytes discarded Number of transmit frames discarded due to: CRC error (S) egress Q depth exceeded (S) egress DE threshold exceeded source abort physical link failure (T1) ATM cells—Number of cells transmitted to BNM Number of cells transmitted with CLP bit set Number of OAM AIS cells transmitted (S) Number of OAM FERF cells transmitted (S) Number of BCM cells transmitted Number of OAM end-end loopback cells transmitted (S) Number of OAM segment loopback cells transmitted Number of cells received from BNM Number of cells received with CLP bit set Number of OAM AIS cells received (S) Number of OAM FERF cells received (S) Number of BCM cells received Number of OAM end-end loopback cells received (S) Number of OAM segment loopback cells received Number of OAM cells discarded due to CRC-10 error (S)
Statistics:	All previous counters followed by an (S) can be configured as statistics
Diagnostics:	Last unknown LCN received cells with unknown LCN count

Card General

Indicators:
Per Card:	Active (green), standby (yellow), fail (red)
Lines (one per):	Active and okay (green) Active and local alarm (red) Active and remote alarm (yellow)
Maintenance/Serviceability Features:	Internal problem isolation loopbacks hot-pluggable
Reliability:	> 65000 hours MTBF
Card Size:	FRSM-8T1: 7.25 in. x 16.25 in. LM-DB15-4T1: 7.0 in. x 4.5 in. Power: -48V DC, 30W (8 T1s)

FRSM-8E1 Specification

Service Interface

Line Interface connector:	RJ-48 when used with LM-RJ-48-8E1 line module SMB when used with LM-SMB-8E1 line module
Line Rate:	2.048 Mbps ± 100 bps
Synchronization:	Transmitter can be either loop-timed to receiver or synchronized to shelf (called normal mode)
Input Jitter Tolerance:	Per G.703
Output Jitter Generation:	Per G.703
Physical Layer Alarms:	LOS, OOF, AIS, RAI
Number of Frame Interfaces:	1 to 31 occupying n where 1 < n < 31. Sum of all < 31 for CCS 1-30 for CAS
Frame Relay Interface Rates:	Either 56 Kbps or n * 64 kbps; n as defined previously
Frame Relay Interface:	Per ANSI T1.618, 2-octet header
Frame Relay Performance Counters (per port; n x DS0):	Receive frames discarded due to aborts Receive frames discarded due to illegal header (EA bit) (S) Receive frames discarded due to CRC errors (S) Receive frames discarded due to alignment errors (S) Receive frames discarded due to unknown DLCI (S) Receive frames discarded due to illegal frame length (S) Receive frames discarded due to DE threshold exceeded Receive frames with DE already set Receive frames with FECN already set Receive frames with BECN already set Receive frames tagged FECN Receive frames (S) Receive bytes (S)
	Transmit frames discarded due to underrun Transmit frames discarded due to abort Transmit frames discarded due to egress Q-depth exceeded (S) Transmit bytes discarded due to egress Q-depth exceeded (S) Transmit frames discarded due to egress DE threshold exceeded Transmit frames (S) Transmit bytes (S) Transmit frames with FECN set (S) Transmit frames with BECN set (S) LMI receive status inquiry request count (S) LMI transmit status inquiry request count LMI invalid receive status count (S) LMI signaling protocol (keep alive time-out count) (S) LMI sequence number error count (S) LMI receive status transmit count (in response to request) LMI transmit status transmit count (in response to request) Transmit frames during LMI alarm (S) Transmit bytes during LMI alarm (S) LMI update status transmit count (in response to configuration changes)
Diagnostics (per port):	Last unknown DLCI received

System Interface

ATM Layer:	Per CCITT I.361 and ATM UNI v3.1
AAL Layer:	AAL5 per draft CCITT I.363
FR-Cell Interworking:	Per draft CCITT I.555 and I.36x.1, as summarized in Frame Relay Forum, FR/ATM PVC Interworking Implementation Agreement FERF.5

Virtual Circuits

Channels (Endpoints):	256 per card—can be allocated across any of the Frame Relay interfaces
Counters:
Service Counters:	Number of frames received (S) Number of bytes received (S) Number of frames received with DE already set (S) Number of bytes received with DE already set (S) Number of frames received with unknown DLCI Number of frames received but discarded (S) Number of received bytes discarded (S) Number of received bytes discarded due to exceeded Q-Depth (S) Number of frames received and discarded due to intershelf alarm exceeded DE threshold (S) exceeded Q depth (S) Number of frames received with FECN set Number of frames received with BECN set
	Number of frames received tagged FECN Number of frames received tagged BECN Number of frames transmitted (S) Number of bytes transmitted (S) Number of frames transmitted with DE set (S) Number of frames discarded due to reassembly errors (S) Number of frames transmitted during LMI logical port alarm (S) Number of frames transmitted with FECN set (S) Number of frames transmitted with BECN set (S) Number of transmit frames discarded (S) Number of transmit bytes discarded Number of transmit frames discarded due to: CRC error (S) egress Q depth exceeded (S) egress DE threshold exceeded source abort physical link failure (T1)
	ATM cells: Number of cells transmitted to BNM Number of cells transmitted with CLP bit set Number of OAM AIS cells transmitted (S) Number of OAM FERF cells transmitted (S) Number of BCM cells transmitted Number of OAM end-end loopback cells transmitted (S) Number of OAM segment loopback cells transmitted Number of cells received from BNM Number of cells received with CLP bit set Number of OAM AIS cells received (S) Number of OAM FERF cells received (S) Number of BCM cells received Number of OAM end-end loopback cells received (S) Number of OAM segment loopback cells received Number of OAM cells discarded due to CRC-10 error (S)
Statistics:	All previous counters followed by an (S) can be configured as statistics.
Diagnostics:	8 Last unknown LCN received Cells with unknown LCN count Card general
Indicators:	Per card: Active (green), standby (yellow), fail (red) Lines (one per): Active and okay (green) Active and local alarm (red), Active and remote alarm (yellow)
Maintenance/Serviceability Features:	Internal problem isolation loopbacks Hot-pluggable
Card Size:	FRSM-8E1: 7.25 in. x 16.25 in. RJ48-8E1: 7.0 in. x 4.5 in. SMB-8E1: 7.0 in. x 4.5 in.
Power:	-48V DC, 30W (8 E1s)
Ingress:	8000 cell buffer shared between virtual channels/paths Standard usage parameter control (UPC) Selective cell discard Virtual circuit queuing EFCI setting per VC
Egress:	8000 cell storage capacity shared between four ports Up to 12 user selectable egress queues per port Selective cell discard EFCI setting per queue

FRSM-HS2 Specification

Errors and Alarm Handling

Line Alarms

Control lead inactive
Recovered clock does not match configured line rate

External Interface Specification

General

Frame Relay Interface: Per ANSI T1.618, 2-octet header
ATM layer: Per CCITT I.361 and ATM UNI v3.1
AAL layer: AAL5 per Draft CCITT I.363.
FR-cell interworking: Per Draft CCITT I.555 and I.36x.1, as summarized in ATM-to-Frame Relay Interoperability Implementation Agreement v 1.0

Physical Interface Specification

FRSM-VHS Front Card

Card status indicator LEDs
- Active (green)
- Failed (red)
- Standby (yellow)
Line status indicator LEDs
- Active and okay (green)
- Active and local alarm (red)
- Active and remote alarm (yellow)
Reliability 85000 hours MTBF (target)
Card size 7.25 in. x 16.5 in.
Power 48V DC, 50W (estimate)

FRSM-HS2 Back Card

Power: 5W @ 5V; 6W C @ -5V

FRSM-HS2 Line

Number of HSSI lines 2
Line interface connector SCSI-2
Line framing not applicable
Synchronization: Transmitter can be either loop-timed to receiver (DTE mode), or synchronized to shelf, (DCE mode)
Input jitter tolerance
Output jitter

Statistics and Counters Specifications

FRSM-HS2

Counters (per line)	Receive frames lost due to aborts Receive frames lost due to illegal header (EA bit) Receive frames lost due to CRC errors Receive frames with bit alignment errors Receive frames with unknown DLCI Receive frames with illegal frame length Receive good frame
	Transmit frames lost due to under-run/Abort count Transmit good frame
	LMI status inquiry request count LMI signaling protocol (keep alive time-out count) LMI sequence number error count LMI status transmit count (in response to request) LMI update status transmit count (in response to configuration changes
	Frames FECN set count Frames BECN set count DE frames discarded count
	Number of frames reassembled but discarded due to service interface physical layer alarm
Trouble shooting statistics:	ECN current queue depth (per channel)

Statistics

Service: Number of frames received

Number of bytes received

Number of frames received with DE = 1

Number of frames received but discarded

Number of received bytes discarded

Number of frames received but discarded due to:

- CRC error

- Illegal frame length

- Alignment error

- Abort

Number of frames reassembled and transmitted

Number of frames reassembled and transmitted with DE=1

Number of frames discarded due to reassembly errors

Number of frames transmitted

Number of bytes transmitted

Number of frames transmitted with DE set

Number of frames transmitted during LMI logical port alarm

Frames FECN set count

Frames BECN set count

Number of transmit frames discarded

Number of transmit bytes discarded

Number of transmit frames discarded due to:

- CRC error

- Illegal frame length

- Alignment error

- Abort

- Exceeding DE egress queue threshold

- Physical link failure

ATM cells: Number of cells transmitted to BNM

Number of cells discarded due to intershelf link alarm

Number of cells transmitted with CLP bit set

Number of AIS cells transmitted

Number of FERF cells transmitted

Number of BCM cells transmitted

Number of end-end loop-back cells transmitted

Number of segment loop-back cells transmitted

Number of cells received from BNM

Number of cells received with CLP bit set

Number of AIS cells received

Number of FERF cells received

Number of BCM cells received

Number of end-end loop-back cells received

Number of segment loop-back cells received

Number of OAM cells discarded due to CRC-10 error

Diagnostics: Header of last cell with unknown LCN

Header of last received frame with unknown DLCI

ECN current queue depth

AUSM Specification (4 Port)

Service Interface (T1)

Line Interface Connector:	Miniature 15 pin female DB-15 (100 W)—(Use LM-DB15-4T1)
Line Rate:	1.544 Mbps ± 50 bps (T1)
Synchronization:	Transmitter can be either loop-timed or receiver, or synchronized to shelf (called normal mode)
Line Code:	Bipolar 8 zero substitution (B8ZS) as specified in ANSI T1.408 (T1)
Line Framing:	Extended superframe format (ESF 24 frame multiframe) as ANSI T1.408
ESF Maintenance Functions:	Bit-oriented alarm and loopback messages of ESF Data Link as per ANSI T1.408
Input Jitter Tolerance:	Per ATT TR 62411
Output Jitter Generation:	Per ATT TR 62411 using normal mode synchronization
Physical Layer Alarms:	LOS, OOF, AIS, RAI
Physical Layer Performance Stats:	LCV, LES, LSES, CV, ES, SES, SEFS, AISS, UAS

Service Interface (E1)

Line Interface Connector:	Miniature 15 pin female DB-15 (120 W)—(Use LM-DB15-4E1), BNC (75 W)—(Use LM-BNC-4E1)
Line Rate:	2.048 Mbps ± 100 bps (E1)
Synchronization:	Transmitter can be either loop-timed or receiver, or synchronized to shelf (called normal mode)
Line Code:	HDB3 (E1)
Line Framing:	16 frame Multiframe as in G.704
Input Jitter Tolerance:	As specified in ITU G.823 for 2.048 mbps
Output Jitter Generation:	As specified in ITU G.823 for 2.048 mbps
Physical Layer Alarms:	LOS, OOF, AIS, RAI
Physical Layer Performance Stats:	LCV, LES, LSES, CV, ES, SES, SEFS, AISS, UAS

ATM Interface

	ATM UNI v3.1, ITU-T G.804, per CCITT I.361
Channel Configuration:	256 per card. Can be allocated across any of the T1 (E1) ports
VPI/VCI:	VPI: 0-255 VCI: 0-4096
Traffic Classes:	CBR, VBR, VBR+
UPC Parameters:	PCR, SCR (VBR), CCDV (CBR)
Congestion Control Support:	ForeSight (toward Network for VBR+)
ForeSight Parameters:	MIR, PIR, Rate Up, Rate Down, QIR, QIR Timeout, IBS

Virtual Circuits

Counters:
Per Port:	Number of cells received from the interface Number of cells received with unknown VPI/VCI Last known VPI/VCI received from the port Number of cells discarded due to error in cell header Number of cells received with nonzero GRC field Number of cells transmitted to the interface Number of cells transmitted for which EFCI was set Number of egress cells discarded due to service interface physical alarm
Endpoint (channel):
Ingress:	Number of cells received from port Number of cells received from the port with CLP = 1 Number of cells received from the port with EFCI = 1 Number of cells from the port discarded due to queue exceeded QDepth Number of cells (with CLP) set) discarded due to queue exceeded CLP threshold Number of cells from the port for which CLP was set due to UPC violations
ATMizer channel counters:
Ingress:	Number of cells transmitted to cell bus Number of cells to cell bus for which EFCI was set Number of cells to cell bus discarded due to shelf alarm
Egress:	Number of cells received from the cell bus Number of cells discarded due to queue exceeded QDepth (per egress Q) Number of cells discarded due to queue exceeded CLP threshold (per egress Q) Number of cells received with CLP = 1
Other Counters:	.
Ingress:	Number of OAM cells discarded Number of AIS cells received from the port Number of RDI (FERF) cells received from the port Number SegmentLpBk cells received from the port Number of SegmentLpBk cells transmitted to cell bus
Egress:	Number of OAM cells discarded Number of AIS cells transmitted to the port Number of SegmentLpBk cells transmitted to the port Number of SegmentLpBk cells received from the port
Diagnostic Stats:	Peak Queue Depth (Ingress: per channel)

Card General

Indicators:
Per Card:	Active (green), standby (yellow), fail (red)
Per Line:	One per line: Active and okay (green) Active and local alarm (red) Active and remote alarm (yellow)
Maintenance/Servicability:	Facility loopback using loop up/down per ANSI T1.408 and ATT TR 62411 (T1), CCITT G.7xx (E1) Facility loopback using management console Internal problem isolation loopbacks Hot pluggable
Card Size:	7.25 in. x 15 in.
Power:	-48V DC, 30W
Safety:	EN 60950 2nd edition (including EN 41003) UL 1950 2nd edition
Compliance:	T1: Accunet 62411 E1: G.703, G.823
ESD:	IEC 1000-4-2

CESM-4T1/E1 Specification

Note The CESM-4T1/E1 specification is the same as the FRSM-4T1/4E1 specification except as shown in the following sections.

Service Interface (T1/E1)

Synchronization:	Transmitter is synchronized to the shelf (Stratum traceable)
Line Framing:	None
Channel Configuration:
Number of CBR Interfaces:	4
Cell Delay Variation (CDV):	Configurable by setting reassembly buffer depth to a maximum of 250 msec. CDV = 1/2 buffer depth

Virtual Circuits

Channels (Endpoints):		One per physical port
Counters:		MIB Name
AAL1:
	Number of lost SAR-PDUs Number of buffer overflow events Number of buffer underflow events Number of SAR-PDU's with header error Number of SAR-PDU's received out of sequence Number of cells played out to T1/E1 port Number of cell generated from T1/E1 port Number of bytes discarded due to shelf alarm from port Number of all 1's cells inserted during buffer underflow Number of bytes discarded due to egress overflow	cesLostCells cesBufOverflows cesBufUnderflows cesHdrErrs cesCellSeqMismatchCnt cesReassCells cesGenCells cesIngrDiscardedBytes cesUflowInsCells cesOflowDropBytes
Diagnostic:	Egress buffer depth (per port)
Alarms:		MIB Name
T1/E1 Port:	Red, loss of signal (LOS) Blue, alarm indication signal (AIS)	LineAlarmState—bit 5 set LineAlarmState—bit 2 set and cesChanState = 3
	Line code violation (LVC)	LineStatisticalAlarmState
SAR Port:
Transmit State:	SendingAIS Sending FERF	cesXmtATMState = 3 cesXmtATMState = 4
Receiving State:
	Receiving AIS Receiving FERF Cell loss	cesRcvATMstate = 3 cesRcvATMstate = 4 cesCellLossStatus = 2

Note All service specific alarms, except red, are passed through transparently.

Loss of signal (red) at CBR interface results in all 1's cells being transmitted.

Brief periods of cell loss "Starvation" results in insertion of 47 octects of 1's.

Extended periods of cell loss results in all 1's (unframed AIS) being generated.

During periods of cell bus configuration SAR-PDUs are discarded.

MATM Specification

Physical Interface (T3.T1) RJ48-T3T1-LM
T1 Line Interface Connector:	Miniature RJ-48C, 100 ohms balanced
T3 Line Interface Connector:	BNC, 75 ohms unbalanced
Physical Interface (E3.E1) RJ48-E3E1-LM:
E1 Line Interface Connector:	Miniature RJ-48C, 100 ohms balanced
E3 Line Interface connector:	BNC, 75 ohms unbalanced
Physical Interface (E3.E1B) SMB-E3E1-LM:
E1 Line Interface Connector:	Miniature SMB, 75 ohms unbalanced
E3 Line Interface Connector:	Miniature SMB, 75 ohms unbalanced

Physical Layer Interface T1:

Line Rate:	1.544 Mbps ± 50 bps
IMATM Synchronization:	Digital PLL to synchronize all transmitters to one of the following: the T3 line, any of the T1 lines, or the MGX 8220 shelf 8 kHz clock
Line Code:	Bipolar 8 zero substitution (B8ZS) as specified in ANSI T1.408
Line Framing:	Extended Superframe Format (ESF 24 frame multiframe) as in ANSI T1.408
Input Jitter Tolerance:	Per ATT TR 62411
Output Jitter Generation:	Using normal mode synchronization per ATT TR 62411
Physical Layer Alarms:	LOS, OOF, AIS, RDI
Physical Layer Performance Parms:	LCV, LES, LSES, CV, ES, SES, SEFS, AISS, UAS

Physical Layer Interface E1

Line Rate:	2.048Mbps ± 100 bps
IMATM Synchronization:	Digital PLL to synchronize all transmitters to one of the following: the E3 line, any of the E1 lines, or the MGX 8220 shelf 8 kHz clock
Line Code:	HDB3 (E1)
Line Framing:	16 frame multiframe as in G.704
ESF Maintenance Functions:	None
Input Jitter Tolerance:	As specified in ITU G.823 for 2.048 mbps
Output Jitter Generation:	As specified in ITU G.823 for 2.048 mbps
Physical Layer Alarms:	LOS, OOF, AIS, RDI
Physical Layer Performance Parms:	LCV, LES, LSES, CV, ES, SES, SEFS, AISS, UAS

Physical Layer Interface T3

Line Rate:	44.736 Mbps ± 20 ppm (T3)
Line Code:	B3ZS for DS3
Framing:	Physical layer conversion procedure for DS3 to ANSI TA-TSY-000772 and TA-TSY-000773
Input Compliance:	Per ATT 54014 and CCITT G.703

Physical Layer Interface E3

Line Rate:	34.368 Mbps ±20 ppm (T3)
Line Code:	HDB3 for E3
Framing:	Per ITU-T Recommendation G.804 and G.832
Input Jitter Tolerance:	Per ATT TR 62411
ATM Interface:
Cell support (type)	STI cells
Congestion Control:	EFCI/FFCI setting on egress (AIM)
EFCI setup:	Using programmable EFCI threshold
IMATM Alarms:	Complies with DS3 and G.832 physical layer protocols and supports FERF, LOS, LOF, OOF, AIS, yellow and red alarms

AIM Groups and Links

Counters:
High Speed Port:	DS3/E3 physical layer line alarm indication and insertion DS3/E3 SUNI-PDh number of cells: Tx and Rx PLL clock recovery status
AIM Group:	Number of cells received from AIM interface Number of cell discarded due to error in cell header Number of cells from AIM interface discarded due to queue Full on both Ingress and egress directions Number of ACP cells received Number of ACP cells received with errors Number of LCP cells received Number of LCP cells received with errors
	Number of cells served from Egress queue to AIM interface Number of cell transmitted by trunk interface, two types: Date and Filler + Data Number of times a link went off the IMAIM group
ATMizer (cellbus) counters:
Ingress:	Numberof cells transmitted Number of cells discarded due to shelf alarm
Egress:	Number of cells received Numberof cells discarded due to queue depth exceeded Q-Depth

Card General

Indicators:
Per Card:	Active (green), standby (yellow), fail (red)
Lines (one per):	Active and okay (green) Active and local alarm (red) Active and remote alarm (yellow)
Maintenance/Serviceability Features:	Internal problem isolation loopbacks Hot-pluggable
Card Size:	IMATM front card: 7.25 in. x 16.25 in. RJ48-T3T1-LM: 7.0 in. x 4.5 in. RJ48-E3E1-LM: 7.0 in. x 4.5 in. SMB-E3E1-LM: 7.0 in. x 4.5 in.
Power:	-48V DC

Table of Contents

Specifications

BNM-T3 Specification

Intershelf Link

Card General

BNM-E3 Specification

Intershelf Link

Card General

BNM-155 Specifications

Intershelf Link Specifications

Common Specifications

SMF Specific Specifications

General Card Specifications

ASC Specification

SRM-T1/E1 Specification

FRSM-4T1 Specification

Service Interface

System Interface

Virtual Circuits

Card General

FRSM-4E1 Specification

Service Interface

System Interface

Virtual Circuits

FRSM-8T1 Specification

Service Interface

System Interface

Virtual Circuits

Card General

FRSM-8E1 Specification

Service Interface

System Interface

Virtual Circuits

FRSM-HS2 Specification

Errors and Alarm Handling

Line Alarms

External Interface Specification

General

Physical Interface Specification

FRSM-VHS Front Card

FRSM-HS2 Back Card

FRSM-HS2 Line

Statistics and Counters Specifications

FRSM-HS2

Counters (per line)

AUSM Specification (4 Port)

Service Interface (T1)

Service Interface (E1)

ATM Interface

Virtual Circuits

Card General

CESM-4T1/E1 Specification

Service Interface (T1/E1)

Virtual Circuits

MATM Specification

Physical Layer Interface T1:

Physical Layer Interface E1

Physical Layer Interface T3

Physical Layer Interface E3

AIM Groups and Links

Card General