Cisco Unified CallManager Device Package 4.1(78.0)
Release Notes
These
Device Package release notes contain important information about installation
procedures and resolved caveats for Cisco Unified CallManager Device Package
release 4.1(78.0).
Note: Before you install this Cisco Unified CallManager
Device Package, Cisco recommends that you review the “Important Notes” section for
information about issues that may affect your system.
Determining
the Software Version
Compatibility
Matrix and Supported Upgrades
Important
Notes & Recommendations
Resolved
Caveats for Cisco Unified CallManager Device Package
Locale
Installer for Cisco Unified CallManager
Cisco
Product Security Overview
Reporting
Security Problems in Cisco Products
Obtaining
Technical Assistance
Cisco
Technical Support Website
Definitions
of Service Request Severity
Obtaining
Additional Publications and Information
This
document provides installation instructions for this Cisco Unified CallManager
Device Package and endpoint related changes.
Note: Failure to follow installation instructions as described
may result in inconsistent Cisco Unified CallManager behavior.
Make sure
that you install and configure this release of Cisco Unified CallManager on
approved Cisco hardware. You can access the correct Cisco-approved server
configuration at the following URL: http://www.cisco.com/en/US/products/hw/voiceapp/ps378/prod_brochure_list.html.
You can
determine the version of Cisco Unified CallManager software that is running on
your server by accessing Cisco Unified CallManager Administration and then
clicking Details.
This Cisco
Unified CallManager Device Package release is compatible with the following
Cisco Unified CallManager versions.
|
4.1(3) |
Note: Review
the history file in your Cisco Unified CallManager in order to determine what
Device Package you currently have installed. If you are preparing to install an
older Device Package than is currently on your Cisco Unified CallManager, you
will receive the following error “This Device Package is older than the Device
Package already Deployed. It is recommended that you should exit
now. EXIT now?”
NOTE: Be aware
that the release of Cisco IP telephony endpoints does not always coincide with
Cisco Unified CallManager releases. It is recommended that you upgrade to the
latest firmware. For the most current compatibility combinations and defects,
refer to the following locations:
Endpoint
firmware: http://www.cisco.com/cgi-bin/tablebuild.pl/ip-7900ser Endpoint documentation, including release
notes: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/english/
Cisco Unified CallManager Device Package 4.1(78.0) includes the following
firmware versions:
|
Firmware |
4.1(3) Devpack 78 |
|
7914 14-Button Line Expansion Module |
S00105000300 |
|
Analog Access WS-X6624 |
A00204000013 / A0034322 |
|
Digital Access WS-X6608 |
D00404000032 / D0054322 |
|
Conference Bridge WS-X6608 |
C00104000001 / C002E031 |
|
Media Termination Point WS-X6608 |
M00104000006 / M002E031 |
|
IP Phone 7902g |
CP7902080002SCCP060817A |
|
IP Phone 7905g |
CP7905080003SCCP070409A |
|
IP Phone 7906 |
SCCP11.8-3-5S |
|
IP Phone 7910 |
P00405000700 |
|
IP Phone 7911 |
SCCP11.8-3-5S |
|
IP Phone 7912g |
CP7912080003SCCP070409A |
|
IP Phone 7920 |
cmterm_7920.4.0-03-02 |
|
IP Phone 7921 |
D00404000031 |
|
IP Phone 7921G |
CP7921G-1.1.1 |
|
IP Phone 7935 |
P00503021900 |
|
IP Phone 7936 |
cmterm_7936.3-3-16-0 |
|
IP Phone 7937 |
apps37sccp.1-2-1-0 |
|
IP Phone 7940/7960 |
P00308000900 |
|
IP Phone 7941/7961 |
SCCP41.8-3-5S |
|
IP Phone 7942/7962 |
SCCP42.8-3-5S |
|
IP Phone 7945/7965 |
SCCP45.8-3-5S |
|
IP Phone 7970/7971 |
SCCP70.8-3-5S |
|
IP Phone 7975 |
SCCP75.8-3-5S |
|
IP Phone 7985 |
cmterm_7985.4-1-6-0 |
|
Media Termination Point WS-X6608 |
M00104000006 |
Note: It is very important to disable platform agents and
services, such as NetIQ and Prognosis performance monitoring, Cisco-verified
antivirus services and intrusion detection software, remote management services,
and any other monitoring applications that automatically restart services; this
action ensures that your system does not encounter issues that are associated
with these services.
Cisco provides the following
guidance to help you successfully install and/or upgrade Cisco CallManager
software:
To minimize call-processing interruptions during the upgrade process,
make sure that all servers are running the same version of Cisco Unified CallManager
software before beginning this upgrade.
Make sure that the servers are online before you begin this Device Package installation; otherwise, pre-upgrade checks may fail or return faulty information.
For optimum performance, apply the most current OS upgrade and SR before you install the Cisco Unified CallManager Device Package. For more information, refer to Cisco IP Telephony Operating System, SQL Server, Security Updates at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/osbios.htm.
If you are using Cisco Unified CallManager Security Agent, you must DISABLE this software and then restart your system before you proceed with this installation.
All nodes in
the cluster run through a database replication check during the upgrade process
as an extra measure, even though the publisher's database replication check
should catch any replication errors clusterwide.
If you encounter a
warning message on any node during this check, make sure that you stop the
installation process and check the log files. Follow the recommendations listed
below if the log file displays any of the following messages:
“All
agent-implementing jobs are waiting to start”
“At least one
agent-implementing job is attempting to execute after a previous failure“
“At least one agent-implementing job has failed to execute successfully“
Be sure to DISABLE any antivirus and intrusion detection software, along with any other security services; then, restart your server before you run the upgrade process. You must manually re-enable these services after the installation is complete.
Make
sure that you disable the following Cisco-verified platform agents and
applications; these products may interfere with the Cisco Unified CallManager
installation:
Server
management agents
VOIP
monitoring/performance monitoring
Remote
access/remote management agents
Note: It is very important to disable platform agents and
services, such as NetIQ and Prognosis performance monitoring, Cisco-verified
antivirus services and intrusion detection software, remote management
services, and any other monitoring applications that automatically restart
services; this action ensures that your system does not encounter issues that
are associated with these services.
Note: To verify that the installation completed
successfully, follow the instructions in Step 5 in the Installation
Instructions section.
Note: Cisco recommends that you apply this Device Package
during a maintenance window.
Procedure
NOTE: Apply this patch to all of your Cisco CallManager
servers, beginning with the publisher server and TFTP server.
When
applying this Device Package to enable new device support, a
cluster-wide reboot is required for those devices to
register successfully. A clusterwide reboot IS NOT required when running to update existing firmware/support.
If installing on a Cisco Unified CallManager
version earlier than 4.1(3)sr2, the following message will be displayed:
“Install on all nodes is required. All nodes will be rebooted as
part of the installation.”
If installing on Cisco Unified
CallManager 4.1(3)sr2 (recommended), the following message will be
displayed: "Install on Publisher and TFTP server is required.
Installation on all nodes is highly recommended." A clusterwide
install/reboot is required.
Perform the
following procedure to install Cisco Unified CallManager Device Package X.X.exe:
1. Download the ciscocm-4-1-DevPack-X.X.exe file to your hard
drive. Make a note of the location where you saved the file.
2. Double-click on the downloaded file to begin the
installation.
3. Click Yes when the installation process
displays a message that asks if you want to install this Device Package.
4. The remainder of the
installation process continues without any additional user input.
5. Towards the end of the install
it will prompt you "Update ALL devices firmware defaults?",
(IMPORTANT) If you click "yes", it will change the default firmware
load for all devices to the latest load packaged with this device pack, click
"no" if you want to change the loads manually yourself later.
Note: In order to change the loads manually, you do NOT
need to reinstall this Device Package. The new files will be present in the
C:\Program Files\Cisco\TFTPPath folder. Go to CCMAdmin->System->Device
Defaults and manually change the name of the load file (for specific device(s))
to the new load and click UPDATE. Next, reset the affected devices for them to
upgrade to the new load.
The system will ask you if you want to view
the logfile when the installation is complete.
6. Verify that the
installation completed successfully by taking the following actions:
a.
When the system prompts you to view the log file, if the
number of errors listed in the dialog is "0", you can select No.
b. If the number of errors detected was greater than 0, select Yes to view the logfile and scroll down to the end of the log file. The errors section at the bottom of the log file will be updated with a corresponding severity.
c.
Reset affected devices in order for them to
obtain new firmware loads, or reboot the cluster.
Note: If the TFTP server is a separate server from the
Publisher, the Cisco TFTP service needs to be stopped and restarted on the TFTP
server before performing this step, unless the cluster (including the TFTP
server) is being rebooted.
Change
the device defaults for devices you wish to roll back. From the Cisco
Unified CallManager Administration page go to System/Device Defaults and set
the devices that were changed previously back to their previous firmware
setting. Select update, and then reset those devices.
The system may create or edit the following log
files during the installation process:
c:\program files\common files\cisco\logs\CCMPatch\Cisco
Unified CallManager X.X DevPackXX Installation YYYY-MM-DD HH.mm.log
(this file is also accessible by navigating to the Start menu shortcut
"Cisco Install Logs" under the CCMPatch folder)
c:\install\dbinstall\dbinstallXXX.txt
c:\program files\common files\cisco\logs\CCMPatch\sqlX.txt
c:\program files\common files\cisco\logs\history.log
Known Caveats in this DP:
CSCsi68438: The
installshield engine (ikernel.exe) could not be launched
This Device Pack contains the following fixes:
|
4.1-Devpack 78 |
|
|
7937 1.2(1) CUCM vob
check in defect |
|
|
3.3(16) and 3.2(19) CCM
vob commit |
|
4.1-Devpack 77 |
|
|
7925 |
|
|
Add 7925 support files
(CSV, XML, GIF) to CUCM |
|
4.1-Devpack 76 |
|
|
Adding 8.3(5) phone
firmware to CUCM |
|
|
7985 |
|
|
CCMUser page has no user
guide for 7985 |
|
|
7985 phones reply with
ResponseItem Status="OK" instead of "0" |
|
|
Some of the fields on the
phone's XML web pages have wrong information |
|
|
SSH password field is
only 7 characters wide |
|
|
Unable to register 7985
to TFTP server which is not default |
|
|
7985 fails to pickup
parked call/initiate adhoc hardware conference |
|
|
CfwdAll Display message
is not getting refreshed. |
|
|
7985- Changing the CCM
version doesnt change the background image. |
|
|
7985 need to support
non-overlapping preference for video codecs |
|
|
Phone ignores CDP when
using Admin VLAN with PC Voice VLAN Disabled |
|
|
7985 not displaying
status correctly if MeetMe conference creater . |
|
|
Operational impacting
debug commands should not been available by telnet |
|
|
when incoming call from
IPVC, 7985 does not display correct video rate |
|
|
7985 "Download User
Guide" link does not link directly to User Guide |
|
|
7985- Unable to make call
from directory, from 2nd/other lines. |
|
|
7985- If DNS resolution
failed to CCM1, CCM1 doesnt appear in CM list. |
|
|
CCM4.2 - Cisco 7985 No
Red Pickup Light Notification |
|
|
Visual Pickup
Notification sometimes does not overwrite status line |
|
|
Network statistics stop
refreshing when switching screens |
|
|
7985-video-disabled &
background image changed, new image seen other end |
|
|
7985- Phone displays
"Rejected by CM "%S"" when autoreg disabled. . |
|
|
7985- Instance of call on
phone not visible in a scenario. . |
|
|
7985- When all CUCMs
service stopped, 7985 should display Registering. |
|
|
Phone service input
fields don't display pop-up box showing char choices |
|
|
7985- 20ms packetization
and phone still gets stuck intermittently |
|
|
Need to remove RFC2833
Disabled parameter for 7985 phone in CCM Admin |
|
|
7985- Status Not Updated
Until OffHook/OnHook |
|
4.1- Devpack 75 |
|
|
6608/6624 |
|
|
6608Fix help file URL for
CCM 6.0 |
|
4.1-Devpack 74 |
|
|
7940/7960 |
|
|
Pressing Cancel while
Requesting RingList File displays two Ring Type |
|
|
7960 shows 1 packet
RXLost at start of every call |
|
|
Firm 8.0.5 , Delay in
accessing corporate directory on 7940/7960 Phones. |
|
|
Secure ephone configured
with octal Dn for more than 3 button reload |
|
|
7940 Russian Phones show
garbage characters in Calls History |
|
|
7960 is not doing HTTP
redirects properly when connected to Phone Proxy |
|
|
7960/40 EAPOL-Logoff
functionality |
|
|
SCCP phone being told to
play DTMF * but playing DTMF C |
|
|
After a callback warning
pressing dial plays dial tone and no ring back |
|
4.1-Devpack 73 |
|
|
Locale not displayed
properly after changing from Japanese to English |
|
4.1-Devpack 72 |
|
|
Announcement identified-
53 not found. |
|
4.1-Devpack 71 |
|
|
Adding 8.3(4)SR1 phone
firmware to CUCM |
|
4.1-Devpack 70 |
|
|
7937 1.1(1) CUCM vob check
in defect |
|
4.1-Devpack 69 |
|
|
Link 'View the User Guide
for your phone' not available for 7911/7970 |
|
|
PLKs on 8.3 phones have
"???" labels when talking to pre-6.0 CCM |
|
|
7921 |
|
|
Check-in Cisco 7921
firmware version 1.1(1) to CallManager |
|
|
7940/7960 |
|
|
DNS Response Parsing
Stack Overflow |
|
4.1-Devpack 68 |
|
|
Update 7921 CSV and XML
files for Release 1.1 FCS |
|
|
6608 |
|
|
E1 Port on WS-6608 5.4(2)
not replying to external ping (ICMP) packets. |
|
|
ICMP is disable for 6608
Device |
|
4.1-Devpack 67 |
|
|
Hear clicking when
headset is attached and display is on |
|
|
No audio if source reset
RTP timestamp in the middle of a call |
|
|
GUI process can lock up
when receiving XML messages |
|
|
phone unregisters when
making toll free and long distance calls |
|
|
7921 Reboots with race
condition between HTTP and SCCP |
|
|
7921 queues SCCP reset
when not in main idle screen |
|
|
7921 sends SCCP
Unregister message unexpectedly |
|
|
Corporate Directory
blanket search does not display all results |
|
|
7921 sources RTP from
random port rather than port specified in olc |
|
|
7921G phone cannot access
Corporate Directory |
|
|
7921 roaming improvements |
|
|
7921 does not place the
softkeys in the specified order |
|
|
7921 does not dial * or the
# before the dial strings |
|
|
7921 does not dial out on
available line if shared line 1 is in use |
|
|
Ver 1.0(4) incorrectly
display softkey Login, Flash, Acct used by CME |
|
|
7921 phones will register
max 2 lines when in srst mode |
|
|
7921 uses EAP-FAST vs
LEAP when in AKM mode and set for CCKM only |
|
|
7921G error on activating
SSID with 20+ chars |
|
|
Speaker Phone Activates
when Phone Answered |
|
|
7921 fallback failure
from SRST to CUCM . |
|
|
7921 only roams on max TX
retries with APs not supporting QBSS |
|
|
7921 loses localized
tones after reset |
|
4.1-Devpack 66 |
|
|
Adding 8.3(3)Sr2 to all
CUCM builds . |
|
|
7911 LCD glimmer /
flicker when florescent light is on |
|
4.1-Devpack 65 |
|
|
Adding 8.3(3)Sr2 to all
CUCM builds . |
|
|
Removing eHook feature
from 11/06, 31, 41/61 and 70/71 phone models |
|
|
Ehook- CCM Feature
Description uses "Ehook" term . |
|
|
7985 |
|
|
When registering to TFTP
server the Call Manager Config is incorrect |
|
|
Toggle Alpha Transparency
of Menus using full screen key with 3 states |
|
|
On CME, 7985 took ~7 sec
to close video chann if CUTA press Hold |
|
|
Mobility cell pickup
feature is not supported on 7985 |
|
|
Status line is not
updated when Call Forward All is performed |
|
|
Unable to activate
callback from 1st line to 2nd line which is shared DN |
|
|
7985- Hit redial after
call from 2nd line & CB, call goes out of 1st lin |
|
|
7985- Phone restarts
during active call if nw settings changed & saved. |
|
|
7985- Transfer from Line1
to Line2 on 7985 doesnt work. |
|
|
7985- ringer stops when
callback hit in a scenario. |
|
|
7985 phone doesnt display
meetme number in a meetme conference. |
|
|
Services button not
working when DNS returns wrong address for CM5.x |
|
|
7985- Displays "From
Unknown Number" on shared line, when call placed. |
|
|
7985 - dialled digits are
dropped, dialing from Directory in a scenario |
|
|
7985- Dialling from
directory doesnt initiate newcall in a scenario. |
|
|
7985- nw config locked,
still erase button accessible in a scenario. |
|
|
7985- gap before first
speed dial |
|
|
7985- Wrong softkey
template is retained |
|
|
7985- G729 codec time lag
is too long. |
|
|
7985-No PC port
connectivity when phone is in voice vlan |
|
|
7985 does not acknowledge
reset message |
|
|
7985 does not failback
when secondary CME is not available |
|
|
7985 does not support
video bit rates of less than 64kbps |
|
|
7985 Can not disable
advertisement of g.722 codec |
|
|
7985- should be able to
handle audio only conference (testing only) |
|
|
7985- changes to reflect
Cisco Callmanager product name change |
|
|
Phone uses old Alt tftp ip
instead of existing. |
|
|
7985- **#** to unlock
needs to key-in very fast. |
|
|
7985- Phone reboots on
invoking graphicMenuBoundary test. . |
|
4.1-Devpack 64 |
|
|
Removing eHook feature
from 11/06, 31, 41/61 and 70/71 phone models |
|
|
Update Load_ID.prm for
7937 phone |
|
|
Check in Guinness phone
firmware to CallManager |
|
4.1-Devpack 63 |
|
|
Adding TNP 8.3(3) and
7937 1.0(1) to CUCM |
|
4.1-Devpack 62 |
|
|
Adding TNP 8.3(3) and
7937 1.0(1) to CUCM |
|
4.1-Devpack 61 |
|
|
Adding TNP 8.3(3) and
7937 1.0(1) to CUCM |
|
|
Adding 8.3(3) features |
|
4.1-Devpack 60 |
|
|
7985 Can not disable
advertisement of g.722 codec |
|
4.1-Devpack
59 |
|
|
Extra button templates are displayed for
7937 |
|
|
Update the QED setting for the 7937 phone
guide |
|
|
User Guide added for new IP Phone 7937 |
|
|
7921 |
|
|
High multicast can impact battery life |
|
|
Proxy URL is not supported |
|
|
Can not reset phone when idle url is active |
|
|
7921 cannot resume shared line hold calls
beyond the first |
|
|
7921 doesn't show missed calls when keypad
is locked and LCD went off |
|
|
No audio if source reset RTP timestamp in
the middle of a call |
|
|
7921 enters speakerphone mode after call
park retrieval with CME |
|
|
Current volume can get impacted while
configuring other volumes |
|
|
7921 with CME speed dial can corrupt system
message display |
|
|
headset mic audio may distort if in noisy
environment |
|
|
DnD does not work with CME on 7921 |
|
|
Get a 10 second audio gap after receiving
deauth with static WEP128 |
|
|
Alert tone does not always play when pushed
via Play URI |
|
|
CM-6608 CFB/MTP |
|
|
KeepAlive interval with CM-6608 CFB/MTP
resources |
|
4.1-Devpack
58 |
|
|
Update English locale Files into the CCM
branches for 8.3.3 release |
|
|
Locale Changes |
|
4.1-Devpack
57.1 |
|
|
7940 - 7960 Do not upgrade to P00308000700 |
|
4.1-Devpack
57 |
|
|
7942/7945/7962/ |
|
|
7965/7975 |
|
|
Check in New phones (7975/41/45/61/65) firmware to CallManager |
|
|
|
|
|
6608 |
|
|
6608 T1 resets due to bugtrap |
|
4.1-Devpack
56 |
|
|
re-tag XML file for New phones QED |
|
|
7940/7960 |
|
|
multiple issue after upgrade to 3.3.5sr2b |
|
|
Hold call is disconnected when primary
CallManager gets back |
|
|
7906/7911/7941/ |
|
|
7961/7970/7971 |
|
|
New Default Background Image Required |
|
|
Jake Featurette check-in |
|
|
7970- Malformed UDP packet DOS attack causes
phone to freeze |
|
|
Cloudraker-XML Parser- xml parse error on event
ID of Redirect Softkey |
|
|
Cloudraker-SendDigits URI fails to send
in-band dtmf |
|
|
Wideband Handset available for config on
7931. |
|
|
7945/65/75 bounce link on soft reset for
both PC and network ports |
|
|
disable audio output during bootup |
|
|
Alien crosstalk is degraded after CSCsh75383
is fixed |
|
|
7971 DHCP address from data vlan |
|
|
Hearing Aid Compatibility tests failed on
New phones/Wideworld TNP |
|
|
New Default Background Image Required |
|
|
Cloudraker- Missing support of IconIndex in
Title element |
|
|
Hebrew chars position too high in softkeys |
|
|
New phones- nmap TCP connect scan crashes
7945 and 7975 |
|
|
Turbo/7931 sometimes experienced resets
after power recycle |
|
|
75 phone call numbers over flows the spaces
assigned for it |
|
|
7945/65 becomes inactive after CCM down |
|
|
DSP process dies while running the call
features automation script |
|
|
Recording tone plays abnormally during a
call |
|
|
7961 crashed when running Codenomicon https
suite(Test #9) |
|
|
DC bias introduced by noise reduction |
|
|
Cannot answer call by going off-hook |
|
|
call on sharedline lost on phone - both
users hit endcall on other line |
|
|
Update diagnostics in BN2 for 7931 |
|
|
Include Kernel.core into the sylog files for
debug purpose |
|
|
Ph not register afte XML Parser Excep seen
during config file parsing |
|
|
Cloudraker-phone fails to come up if deleted
and tries to Auto-reg SIP |
|
|
Turbo Bootloader Changes |
|
|
7962 does not come up with load 8-3-1-10 |
|
|
7911 phone crash when switching to Arabic
locale |
|
|
797X- Phone DHCP config data got corrupted
during firmware upgarde |
|
|
Phone Directory gives incorrect details
after upgrade to 8.2.2 |
|
|
TNP Phone Update needed for New Zealand DST
changes in 2007 |
|
|
CIA 1085- lower Voice Mail status line to
below DND state. |
|
|
TNP Phone use Narrowband Vol Table even for
WB |
|
|
wrongly uses tftp server as log server |
|
|
Broadcom phones unable to determine source
port of unicast 802.1x EAPOL |
|
|
Rings shouldn't be configured for intercom
lines |
|
|
CallBubbleSelected.png is one pixel too wide
for beamish |
|
|
Ph in stuck state after capfList config
structure change in SEP MAC file |
|
|
Ph got stuck in Settings screen when
Settings is pressed while dialing |
|
|
7970 RLR is softer |
|
|
Phone API startMedia request, parameter
"receiveVolume" not working. |
|
|
7975G characters look fuzzy/not formed
correctly |
|
|
7962/42 advertises PAUSE capable
via Ethernet AUTO-NEG |
|
|
Pixels sourounding the active UI tab are not
black |
|
|
Callback Message screen mixed up with Placed
call screen |
|
|
7970 plays loud comfortable noise when using
G.729 codec |
|
|
Phone sends different help ID for intercom
line |
|
|
Cloudraker- XML parser- Hardened Soft Key
Files schema rules |
|
|
Speed Dials not working on SIP Phones in a
specific scenario |
|
|
TNP sempahore traverse |
|
|
Resource Image updates for FCS |
|
|
Update New phones BN2 for Memory Bist tests |
|
|
Darker greyscale images cause unreadable
display on 7961/41 |
|
|
New phones handsfree mic signal can clip |
|
|
Cloudraker- XML Parser- No Error when tag is
duplicated |
|
|
Update New phones BN2 files with diags
version 13.2.0.60 |
|
|
New phones do not respond to 802.1x
Re-authentication Requests |
|
|
Missed call history incorrect for forwarded
calls |
|
|
Underworld - XML Parser Code changes |
|
|
Underworld- Phone does not shows "bad
ring list" for erroneous ring file |
|
|
Cloudraker- XSI- xml push onFocusGained to
phone executes 3 times |
|
|
SBB/SBCB & Barge/cBarge call instance
focus incorrect after phone reset |
|
|
Update New phones mfg image to include new
diagnostics ver 13.2.0.49 |
|
|
PS loads fails to switchover to Jap locale |
|
|
Resource Image updates for FCS |
|
|
MIDlets- Config File schema errors and
issues |
|
|
XML Schema hardening prevent encrypted &
non-encrypted config parsing |
|
|
7970 with firmware 8.2.2sr1 speaker not
working correctly |
|
|
7962- packets egressing PC port should have
PC vlan untagged. |
|
|
New generation phone have lower volume then
older phone types |
|
|
Null pointer exception on XML Parsing for
SIP phones |
|
|
3rd phones break 802.1x auth when span to pc
enabled |
|
|
ESW clock not initialized properly by boot
loader |
|
|
7962 barge in no voice |
|
|
XML data can't be rendered to IPphone |
|
|
New phones Handset RLR incorrect |
|
|
AEC suppression can degrade voice quality
scores on New phones |
|
|
New phones- Color models are displaying
visual noise on power cycle/reboot |
|
|
Pixels surrounding the active tab are not
black |
|
|
Cloudraker- CFWDALL and MCID not working on
SIP phones |
|
|
TNP SIP phone can not failover to SRST due
to wrong port |
|
|
Start Media Response does not returns codec
string correctly |
|
|
Guinnes handset - "highs" are
little too high |
|
|
7931 Bootloader Changes |
|
|
New XML parser unable to display another Ph
web page in XML services |
|
|
Audioble MWI (Stutter Tone) is not sounds
correct |
|
|
TNP phone corrupt background image causes
blue image and crash |
|
|
Turbo- Malformed UDP packet DOS attack
causes phone to freeze |
|
|
Broadcast Storm one way audio for 7961 SIP |
|
|
Update diagnostics in BN2 for 7911 / 7906 |
|
|
Volume Control on Group Listen is Broken |
|
|
New phones- Malformed UDP packet DOS attack
causes phone to freeze |
|
|
7945/65/75 Hardware version 6.0+
uses external gamma |
|
|
7970- nmap TCP connect scan crashes 7945 and
7975 |
|
|
Analog codec audio output enabled in early
stage |
|
|
802.1x packets are not forwarded |
|
|
SBB feature does not work |
|
|
Update New phones BN2 mfg image to release
signed |
|
|
Need a smaller font for the call reference
for Makaha and Caffreys. |
|
|
Calls transitioning to OFFHOOK state should
take focus |
|
|
send specific XMLobject code into 7970,
phone cannt request EM service |
|
|
New phones- improve AEC doubletalk
performance |
|
|
TNP SCCP ph unable to come up and register
with sidecar 7914 attached |
|
|
Underworld - XSI Backward Compatibility
Changes |
|
|
SDK version updated to 6.0.2 for
8.3.1.release branch [8.3(2)] |
|
|
when callwaiting tone is invoked, calls stop
getting ringback |
|
|
support new Spansion flash part |
|
|
OS PLL init setting unnecessary |
|
|
Resource Image updates for FCS |
|
|
Bogus load name in Phone load element value
cause TNP phone to hang |
|
|
3rd gen phone may loose personalization
after rereg to another CCM |
|
|
831-Settings button access set to restricted
disables directories/servic |
|
|
Phone will not load from case sensitive TFTP
server |
|
|
Bug in vFillShorts assembly source |
|
4.1-Devpack
55 |
|
|
Enable New Model phones (7975/41/45/61/65)
to appear in CUCM Admin Pages |
|
4.1-Devpack
54 |
|
|
Phone does not display full status message
when registration fails |
|
|
7906/11 display square symbol when the
Caller ID too long. |
|
|
Update Device Support |
|
|
7940/7960 |
|
|
7940 / 7960 reboots when receiving IP
fragmented packet |
|
|
7940/7960 phones fail to upgrade LSC with
CME secure authentication |
|
|
Choppy audio/jitter in incoming RTP to 7960
causes one way audio |
|
|
no audio after high delay or jitter on
network with g.729 |
|
|
hook switch debounce timer too short on 7940
IP phone |
|
|
In speakerphone disabled state, 'Dial'
softkey active in a scenario |
|
|
when callwaiting tone is invoked, calls stop
getting ringback |
|
|
7960(sccp) resets under Codenomicon HTTP
test suite running |
|
|
7960/SCCP resets under two cases of
Codenomicon TCP Test suites |
|
|
7960/40 ignores StartTone Messages when in
connected state |
|
|
Phone struck in a loop inside the personal
address book |
|
|
Migrate to use new load authentication key |
|
4.1-Devpack
53 |
|
|
Adding 8.3(1) Display instances to all released
CCM branches |
|
|
7935,7936 |
|
|
Phonebook doesn't display numeric number by
default in Web interface |
|
|
Second phone in a shared line hangs in a
failback and failover scenario |
|
|
Phones hangs while using restore default
from UI in this scenario |
|
|
Phone UI displays error when Restore Factory
default in a active call |
|
|
Fields in "Add New Phone Book
entry" in 7936 GUI do not get refreshed |
|
|
"Server error-413 N/A" appears
when wrong input given in phone book |
|
|
Phone book entries duplicate |
|
|
No validation for "upload logs"
under Diagnostics in phone menu |
|
|
Ping page in GUI does not get refreshed |
|
|
No. of characetrs as password input
inconsistent in GUI and phone menu |
|
|
Call Park Reversion message not displayed |
|
|
Ping input in GUI gets truncated |
|
|
Network settings dont work when 2 phones are
in a call |
|
|
Phone Book does not accept 24 digits as DN |
|
|
Only 23 digits displayed of a 24 digit DN though
lot of space available |
|
|
Softkey templates working improperly |
|
|
CFwdAll in an active call breaks the voice
path |
|
|
CP-7936 v3.3.11 can continually reboot after
a few weeks on HP switch |
|
|
7936 may not dial the * character when using
Phone Book |
|
|
Softkeys missing(7936) ,when huntpilot call
is answered with callfwdall |
|
|
Phone plays ringback tone if destination
phone has CFA set to unknown. |
|
|
Deleting the DN freezes the phone |
|
|
"Http Server" label in place of
Http client |
|
|
DN does not display completely |
|
|
Reboot does not work |
|
|
Pressing menu-> phone button in active
call phione in a wierd state |
|
|
c in click should be capital on
"Passwords/HTTP Port Change" webpage |
|
|
Help page does not show hostname |
|
|
Changing the ringer during an active call
puts the phone on hold |
|
|
Help page of time and date does not list all
the date options |
|
|
The heading for Password page in GUI should
be different |
|
|
Help Page of Network Setup incomplete |
|
|
Softkey templates incorrect in case of
Shared line |
|
|
7936 phones intermittently fails to upgrade
to new load |
|
|
Icelandic characters not shown on 7936 IP
conference phone |
|
|
Spelling of transfer softkey in case of new
call |
|
|
CFwdAll softkey is absent when initiating a
new call during active call |
|
|
7936 DN display only displays 11 digits of a
12 digit DN |
|
|
7936 - tone49(zipzip) has beep beep then
sounds like long euro ringback |
|
|
CP7936 Experiencing Possible ARP Cache
Corruption |
|
|
7936- conference soft keys becomes inactive
after a few calls |
|
|
Need support for
GetElementManagementFromManagedElementOid |
|
|
7935 & 7936 stops after 8dhcp
discoveries w/no response |
|
|
DHCP changes can cause phone to reset while
on a call |
|
|
7936 resets or one-way audio due to
exceptions caused by DHCP renewal |
|
|
7906G,7911,7941, 7941GE,7961, 7961GE,7970,7971 |
|
|
NullPointer Exception on
AutoCallAgentImpl.inFocusItemChanged() events |
|
|
DSP Configuration Files are not Correct |
|
|
7911 DEV load contains incorrect jar file |
|
|
Third-Gen SCCP Retries Registration 20K+
Times/Day On Phone-Reg-Rej |
|
|
R2D- mapPixelCoordinatesToWindow always
returns NULL. |
|
|
Pressing New Call should let user
"Enter Number" |
|
|
M&R- new M&R tone command should
override playing tone of same type |
|
|
Tone not suppose to send to supervisor when
selected remote only |
|
|
Phone does not show complete information for
show inventory command |
|
|
Change the immDiv softkey name to Redirect -
Update SIP dictionary files |
|
|
Need Automation API to get status of
headset, mute and speaker lights |
|
|
Commit of CSCef34402 broke c6slc, other?
pikespeak images |
|
|
make 'DEBUG' trace anticipated for a 1-way
audio problem as NOTICE trace |
|
|
Phone doesn't calculate SRTP auth tag
correct for certain RTP payload |
|
|
DC bias introduced by noise reduction |
|
|
Play URI doesn't play ring file after first
time push |
|
|
New phones- Continuous unicast traffic
resets the phone |
|
|
C-P-7941 Changes on the Ring Tone go back to
Default after a soft reset |
|
|
Update memory timings for 7931 boot loader |
|
|
SIP phone failed to clear Held call when CCM
restarted |
|
|
TNP- keyboard I/O errors on reset |
|
|
No spkrphone dialtone when Trans/Conf button
hit on TNP SCCP 8.3.0.9S |
|
|
ppid found file system issue with unmount
beneath stdio file access |
|
|
Re-partition MIPS memory allocated for ZSP |
|
|
G.722 K-Factor Table incorrect |
|
|
Call duration timer window on ph display
cycles between multiple calls |
|
|
7971-ringer volume is too high |
|
|
7971 unable to come up while detecting
Supplicant on both switch port |
|
|
New phones- Beamish models should not have
touchscreen enable/disable |
|
|
7942/7962- pressing "Cancel" key
does not discard change to contrast |
|
|
Stutter Tone quality problem when using
speaker / line button |
|
|
797X- Phone DHCP config data got corrupted
during firmware upgarde |
|
|
Phone UI locked up when remaining in fail
over mode |
|
|
minimum send gain not consistent |
|
|
Static analysis on debug shell |
|
|
Broadcom phones unable to determine source
port of unicast 802.1x EAPOL |
|
|
CallBubbleSelected.png is one pixel too wide
for beamish |
|
|
Add wideband PLC to codec G.722 and L16K pcm |
|
|
7931- Pressing Line button does not change
Line focus |
|
|
7975 Gigabit is sensitive to CM signal, and
loose many packets |
|
|
Show wrong time when using the Singapore
date time group selection |
|
|
Change dsp cost table for iLBC |
|
|
Noise reduction causes highband rolloff on
handset |
|
|
7931- Overview not in home position at
initial bootup |
|
|
Speed Dials not working on SIP Phones in a
specific scenario |
|
|
DSP resets when Noise Reduction is enabled
and spike in audio signal |
|
|
keypad tones not played on speakerphone when
transfering a call |
|
|
RTCP socket open error may cause audioserver
to spin |
|
|
Fix Static Analysis warnings from TNP
security code |
|
|
EAP-Request/MD5 to PC supplicant could not
pass thru Gig phone |
|
|
7931- Auto Line Select does not work as
expected |
|
|
IP-phones hang when call arrives while
XML-play in progress |
|
|
Phone hangs if it stays on placed calls when
the peer ends the call |
|
|
Third gen phone may behave wrong under
stress registration test |
|
|
New phones- PC port does not forward egress
packets |
|
|
SIP Phone core dumped after failover |
|
|
Disable Speaker/Handset for TNP SIP doesn't
disable Meet me Softkey. |
|
|
echo on New phones speakerphone |
|
|
7970 with firmware 8.2.2sr1 speaker not
working correctly |
|
|
Unusable G711 calls (loud noise) |
|
|
Automation- Need enhancement to AutoStream
for SRTP or RTP |
|
|
Automation does not work on 7911 |
|
|
need interface getLineButtonPosition() to
AutoCallAgentIf |
|
|
Phone- Dial softkey should not be available
for PRIVATE numbers |
|
|
CallHistory Menu- line key, speaker key, no
longer work |
|
|
Remove tftp command from Mirzam ROMMON |
|
|
7971/7941 re-append parameters with a
redirected authentication |
|
|
CDP can alter statically assigned VLAN |
|
|
R2d code doesn't return null reference for
corrupted PNG file |
|
|
TNP SCCP phone displays "???" for
DND linekey |
|
|
Remove I-Hold changes for Enterprise phones |
|
|
3g-phones -- pick up Sun Java patch to
address 2007 DST changes |
|
|
TNP SIP phone needs to be power reset to
re-register in a scenario |
|
|
slower error propagation causing ph to
become leaf of grand child phone |
|
|
7971 Shows NPE when rebooted during inactive
time |
|
|
Incorrect DSP Configuration File Formats |
|
|
7911/7931/7962- DSP process memory leak |
|
|
Filesystem Privilege Escalation |
|
|
Volume Control on Group Listen is Broken |
|
|
When zrun exec VM, it returns
immediately& unmount takes causing Ph loop |
|
|
ppid display notification icon addition |
|
|
Psylocke code review |
|
|
SCCP70.MU-1-0-19S advertises iLBC and causes
the call drop |
|
|
7931- Softkeys not Updated in Alerting State |
|
|
PPID- sunvm should not be trying to come up
while /dnld is occupied |
|
|
Noise Reduction voice metric has erroneous
value |
|
|
New phones- Update LCD device driver for
7975 (Murphys) model |
|
|
supposed lock issue on CNU rebooting
contention problem with init |
|
|
SA errors for activate() methods |
|
|
AutoStream getRemotePort returns neg value
for ports in 60000 range |
|
|
New phones- Psylocke SOC SA/Cleanup |
|
|
Inconsistent display of DND Feature (in line
button) on SIP & SCCP Phone |
|
|
KA timer still alive on child phone; phone
creating new tranfer process |
|
|
Audible MWI support |
|
|
authentication fail on parent, but child
authenticates OK |
|
|
New phones- keypad device driver for 7945 /
7965 models (Beamish) |
|
|
SA baselining for TNP |
|
|
7931-Resume SK does not resume call after
scrolling to another line |
|
|
Merge from DSP Version 4.2 |
|
|
Phone goes out of memory after
upgrade/downgrade due to OutOfMemoryError |
|
|
Hearing Aid Compatibility tests failed on
New phones/Wideworld TNP |
|
|
Hebrew chars position too high in softkeys |
|
|
Comfort Noise needs to be tuned for Wideband
codecs |
|
|
8.3(1) SCCP Phone resets during video setup
with non-CM6.0 Endpoint |
|
|
Display scr. is dark & won't accept
input while phone upgarde downgarde |
|
|
phone as root and leaf for the same file;
two roots for the same file |
|
|
Phone with network plugged into PC port can
get stuck if link drops |
|
|
Osage- Phone drops incoming unicast EAPOL
when VVLAN is present |
|
|
Customer cannot use Codec of their choice
after 8.2 phone load install |
|
|
Parent not sending KA to leaf; leaf reroot;
end up with TLOAD |
|
|
Phones failover to secondary node with wrong
cause code |
|
|
PAE can't exit due to a file lock during
shutdown, phone hangs |
|
|
Cannot answer call by going off-hook |
|
|
call on sharedline lost on phone - both
users hit endcall on other line |
|
|
TNP phones on CME can't resume call with
Line button |
|
|
Focus does not shift to off-hook line while
another call is incoming |
|
|
PPID FOUND CORNER CASE- init never reimages
in certain instance |
|
|
Include Kernel.core into the sylog files for
debug purpose |
|
|
Focus should remain on oldest ringing call
with mulitple incoming calls |
|
|
set ringtone after preview ringtone can
crash a 3rd gen phone |
|
|
NAK SMT/ORC |
|
|
7975 Network Stats page displays the wrong
NW port info |
|
|
New phones- move interrupt learning code to
a helper function |
|
|
MenuApp Application has wrong icon in title
bar |
|
|
Merge Noise Reduction improvements into
Mainline branch |
|
|
Phone Directory gives incorrect details
after upgrade to 8.2.2 |
|
|
Muster- Phone Errors when pushing URL's with
priority |
|
|
offhook w/ handset for the first time after
reboot, no dialtone is heard |
|
|
Filesystem Denial of Service |
|
|
7962/42 advertises PAUSE capable
via Ethernet AUTO-NEG |
|
|
PPID Unit Test Findings - TCP Communication
Problem on Root Removal |
|
|
SIP phones run out of memory in Java heap
for every call |
|
|
XML Parse error when phone is dialing |
|
|
7911/7972- Add tool to dump DSP data
structures, initially msg buffers |
|
|
Remove redundant model specific dictionary
entries |
|
|
Update boot loader on New phones phones |
|
|
Replace TI assert function by dspfw define
ASSERT |
|
|
No dialtone with handset off-hook or using
the Speaker button |
|
|
Change text on Power Save Config menu of
phone from Display to Backlight |
|
|
New phones- Update Touchscreen device driver
for 7975 (Murphys) model |
|
|
New phones- update LED test app for 7975
model |
|
|
SBB/SBCB & Barge/cBarge call instance
focus incorrect after phone reset |
|
|
OnHook Dialing from Line2 doesn't work if
Line1 and Line2 have same DN |
|
|
Not able to configure Directed Call park BLF
in 7970/71 SIP phones. |
|
|
7931- Add Help for Fixed Feature Keys,
NavPad, and LocalFeature PLKs |
|
|
Graphic Issues |
|
|
New phones audio improvements |
|
|
New phones- use port index to update queue
link speed |
|
|
TNP phones fail to upgrade LSC with CME
secure authentication |
|
|
Enhance kernel memory utilities to report
free blocks in the virtual mem |
|
|
7970/71/41/61- DSPBOOTStart-Sync failure btw
ZSP and MIPS-MBOX1=DEAD |
|
|
Need ability to send hook signal for onhook
transfer feature |
|
|
Phone does not come back up when the PC and
sw cables are reversed and r |
|
|
new threaded PPID algorithm with dual TX
threads wont shutdown |
|
|
"Update" softkey isn't displayed
when focus is on LSC |
|
|
Turbo- Malformed UDP packet DOS attack
causes phone to freeze |
|
|
Phones don't handle fatal Java exception
properly |
|
|
IP phone fails to parse the encrypted config
file |
|
|
SIP Tnp Phones display needs to be changed |
|
|
bug trap 91 on system reboot |
|
|
Don't write cdp.conf file everytime we
recieve packet if not necessary |
|
|
Changes per UI Evaluation |
|
|
clean up syslogs in PPID remote and console
logging |
|
|
differentiate illegalStateException in
getNodeId() |
|
|
No help information avail for NAV Left NAV
Right button in 797X phones |
|
|
IDLE Phone with Open detailview screen cause
inconsistant DTMF behaviour |
|
|
CallHistory Menu- Going offhook dials wrong
number in special case |
|
|
With Setting Access to restricted can access
Network Config |
|
|
Phone gets stuck while resetting |
|
|
SIP 7970 phones showing RemoteHeld state
while it has to be in HELD stat |
|
|
/usr/cache out of space - can't create a new
file |
|
|
7961 phone not show Help info for privacy
button |
|
|
Large increase in PNG graphic processing
time |
|
|
Focus should remain on oldest ringing call
with mulitple incoming calls |
|
|
Wideband Handset available for config on
7931. |
|
|
Handset adaptive gain control needs to match
the 7940/7960 |
|
|
Automation- Need isSelected method in
autoobjinfocus |
|
|
Display Timer on TNP Phones wrong, Meet Me
initiated with Trans Pattern. |
|
|
Shared memory access collision between dspfw
and driver |
|
|
JPN- Cannot Display Kanji via
UserToDeviceData |
|
|
Bug trap 91 if TCP server/client resides in
the phone |
|
|
79x1 phone delay to display system message
after deactivate DND |
|
|
Leave space between display of Internal
caller ID and Line Text Label |
|
|
New phones- create unique queue for reserved
mcast |
|
|
turn on WB handset feature bit in mfgInfo
for New phones phones |
|
|
Background Image list item irregularities |
|
|
Intercom- 7931 phone cannot complete onhook
dialing with incoming interc |
|
|
Takes long time to receive error from phone |
|
|
SIP phone stop registering to CCM w/ 50%
packets loss |
|
|
Unknown name displayed if special characters
are in display name |
|
|
dtmf issue in CME software conference |
|
|
7911 Ph unregister flood console logs with
Supplicant logged off message |
|
|
Top of Softkey Graphics Disappears When
Slider Bar is Shown |
|
|
Add debugging info-- add brodcast TX/RX
count to call trace |
|
|
phones should keep the latest Kfactor value
in the phone stats |
|
|
7914 configured over 15 digit in line number
behaves very strange |
|
|
Guiness 7945s got stuck during ppid upgrade |
|
|
some SCCP phone types does not play call
alert or reminder tone for DND |
|
|
CallInfo page displays wrong status for the
idle lines |
|
|
convert "Can Not" to
"Cannot" in all SCCP english dictionary phrases |
|
|
SIP7911 stuck during automated
upgrade/downgrade |
|
|
New phones- Update BN2 to latest diagnostics
version 13.2.0.33 |
|
|
AutoFeatureIf invokeDirect returns success
when softkey press failed |
|
|
Headset LED in wrong state after power cycle |
|
|
CallHistory Menu- Can't dial with line
key|speaker in special cases |
|
|
New phones- update to latest diags for all
New phones phone models |
|
|
Privileged Shell Commands available to
unprivileged user |
|
|
Handle REG ALL FAILED differently to allow
LSC installation |
|
|
Root phone not offerring new leaf when its
children are gone |
|
|
AutoObjInFocusIf.getLabel returns incorrect
information for a call item |
|
|
7975/45/65- Gig E speed option unavailable
Switch port or PC Port settin |
|
|
New phones bugtrap- SY MSG- Kernel Shu=
0x6666 |
|
|
Call Preservation- sccp to sccp intercom call
clearing issues |
|
|
mislist processing removes critical files on
upgrade [stale file problem |
|
|
Need to be able to get the versionStamp for
the config |
|
|
Intercom- phone does not do talkback if
onhook dialing is in progress |
|
|
ESP debug message add (passau) |
|
|
New phones- Implement Psylocke programming
restrictions |
|
|
on speaker, noise or mute tone heard when
pressing Mute button |
|
|
Factory Reset require for secure phone to
move to another CCM |
|
|
3rd phones break 802.1x auth when span to pc
enabled |
|
|
Bugtrap 0x91 phones (during fsck) |
|
|
phone load need to support new timezones |
|
|
New phones- provide register access for gig
testing |
|
|
2nd iLBC channel can't be opened as
full-duplex to do barge-in |
|
|
Collapse muster into tnp_main branch |
|
|
third gen phones power is initally set high
power at boot w/line powered |
|
|
Phone web page http-//Phone IP Add shows ???
character for parameter nam |
|
|
Update 7975 / 7965 / 7945 bootloader for LED
changes in new HW |
|
|
Pre-dial list shows DN followed by
conference after a conference. |
|
|
flash/buffer comparison failing |
|
|
Repeated Dialing from Call History Menus
causes OutOfMemoryError |
|
|
CallInfo URL missing VisibleFeatureList tag
when application pane open |
|
|
Secure conference need support for getting
icons from confList |
|
|
7975- Add touch panel calibration defaults |
|
|
Phone declared as a child twice by same
parent due to keep alives TO |
|
|
SIP Intercom - enable redial feature |
|
|
Audioble MWI (Stutter Tone) is not sounds
correct |
|
|
Time zone rules do not update correctly on
3rd-gen phones |
|
|
7911 phone advertise 2 iLBC codec on its
capability message |
|
|
dhcp memory leak |
|
|
Change dsp cost table for G.722 |
|
|
7941/61 TNP time displays 1 hour early if
power cycle |
|
|
New phones- Malformed UDP packet DOS attack
causes phone to freeze |
|
|
Internal calls are having one way audio |
|
|
802.1x packets are not forwarded |
|
|
Need a smaller font for the call reference
for Makaha and Caffreys. |
|
|
Private RIU calls show up in the callinfo
list |
|
|
IP Phone SSH Vulnerability |
|
|
Read linenumber from the config file |
|
|
Noise Reduction total energy parameter rests
at 28 instead of 0 |
|
|
7970 phone in low power mode consumes more
power than CDP advertisement |
|
|
SenderJoins & Byes values were different
regardless of call status |
|
|
Bogus load name in Phone load element value
cause TNP phone to hang |
|
|
Phone TFTP request packet for a background
image is Malformed Packet |
|
|
New phones- code cleanup in dsp device
driver |
|
|
New phones- Update diags for Murphys to
13.2.0.23 |
|
|
TNP Phone SSH Vulnerability |
|
|
Update diagnostics / BN2 for New phones
phones |
|
|
XML parsing error on LineInfo to turbo
phones w/ speed dial configured |
|
|
MenuApp Application has wrong icon in title
bar |
|
|
7970- Malformed UDP packet DOS attack causes
phone to freeze |
|
|
SIP shows incorrect info for placed intercom
call in IntercomHistory log |
|
|
SIP phone should disable Callback and DND
for intercom call |
|
|
port "reset on sleep mode" ddts to
New phones code base |
|
|
Modify assembly to address Titan Advisory
R5691 and c55 Advisory CPU_116 |
|
|
Multiple softkeys on the phones are
"bleached" on touchscreen drag |
|
|
Need automation API to get tthe time/date
from the phone |
|
|
Update cpk files for Beamish model 7965
phone |
|
|
Need to Press Right button twice on Nav Pad
to close Line Detail |
|
|
New phones- nmap TCP connect scan crashes
7945 and 7975 |
|
|
Composed IPPM messages display + instead of
space |
|
|
Update power requirements for 7945, 7965,
and 7975 phones |
|
|
New phones- Update BN2 to latest diagnostics
version 13.2.0.31 |
|
|
75 phone call numbers over flows the spaces
assigned for it |
|
|
Recording tone plays abnormally during a
call |
|
|
DSP process dies while running the call
features automation script |
|
|
LCD for New phones 7975 need color register
adjustment |
|
|
SIP 7911 and 7961- Erase config from
Settings menu does not reset phone |
|
|
Font kerning issue on 7970 |
|
|
Missing Pixels on the left side of UI
displays on Turbo phones |
|
|
New phones phones need different EQ based on
Handset Hookswitch |
|
|
Phone does not get registered when
daisy-chained with 7961 phone |
|
|
Customer is experiencing one way audio calls |
|
|
TNP improvements- /bin/sh should always be a
POSIX-compliant shell |
|
|
7971GE- Sleep Mode issue |
|
|
7941 - BLF speed-dial status LED does not
work |
|
|
PNG Broken- Phone fails HTTP GET if earlier
HTTP request is not finished |
|
|
wrongly uses tftp server as log server |
|
|
Rings shouldn't be configured for intercom
lines |
|
|
SIP phone does not answer by lifting handset |
|
|
LCD for New phones 7975 phone displaying
inaccurate color balance |
|
|
Phone sends different help ID for intercom
line |
|
|
TNP sempahore traverse |
|
|
Shared line display & going offhook
while in active call distort display |
|
|
command parse error and command search fail
on 7970 |
|
|
JAL doesn't work as per requirement with
c-Barge Conference |
|
|
Frequency Value for Steady Dial Tone After
Stutter is Wrong |
|
|
PPID Unit Test Findings hash test ugliness |
|
|
Jphone and init.tab and sleep interaction |
|
|
Update diagnostics for New phones phones to
version 13.2.0.36 |
|
|
Phone does not get registered when daisy
chained |
|
|
pressline 2 not working for 2nd line of 7941 |
|
|
SCCP phone does not register back to
publisher after restart. |
|
|
GUI stuck after changing contrast |
|
|
SA for img_main (image daemon) |
|
|
Enhancement- provide an indication of when
flash was last formatted. |
|
|
New phones- Fix the printing of the Chip
Version Register (CVR) values |
|
|
Ph hits max file download timer of 60 min
during firmware upgrade downgr |
|
|
TNP Phone 7941 second line line button will
light up for incoming call. |
|
|
SIP phone init a new call when pressing the
line that already has a call |
|
|
Hung RS-232 port causes phone
upgrade failure |
|
|
Response.Redirect fails |
|
|
When ph is going to safe mode or TLOAD its
background should be cleared |
|
|
Ph stuck in IDLE state after Java Error
without CallManager menu Entry |
|
|
7945/65/75 Hardware version 6.0+
uses external gamma |
|
|
7970- nmap TCP connect scan crashes 7945 and
7975 |
|
|
7975- PC port goes no link after
reconfiguring to 1000F |
|
|
G722 Monitoring call could not be setup for
iLBC primary call |
|
|
Memory Leak on phones with repeated calls
with very short call hold time |
|
|
Calls transitioning to OFFHOOK state should
take focus |
|
|
Event needed for reset |
|
|
Change the CiscoError, CiscoStart and
CiscoReboot png files for new logo |
|
|
Phone core dump while running the call
features automation script |
|
|
7971 SIP/SCCP- PC port can be enabled after
being disabled from CCM page |
|
|
|
|
|
Idle sftkeys displayed on new incoming call
after transferw/rel image |
|
|
Erroneous Behavior when DialLine URI on
Intercom Line that has call |
|
|
Gross timeout for downloading file with
DLOAD & TLOAD should be changed |
|
|
when callwaiting tone is invoked, calls stop
getting ringback |
|
|
Host unicast traffic are not forwarded to
the egress PC port |
|
|
support new Spansion flash part |
|
|
7931- localization work for Muster |
|
|
Phone hangs while downloading PNG files |
|
|
7970- implement ethARLCache functions |
|
|
TLoad- timer_start fail -
doGrossTimeout-serial issue seen on 16s load |
|
|
831-Settings button access set to restricted
disables directories/servic |
|
|
Callback softkey is presented but it doesn't
do anything. |
|
4.1-Devpack
52 |
|
|
Locale file - target-dictionary.utf8.xml
needs to be updated |
|
4.1-Devpack
51 |
|
|
7920 |
|
|
7920 Firmware 3.0.2 Check-in |
|
4.1-Devpack
50 |
|
|
Need a way to control SSH access to phone
from CM |
|
|
Check-in Cisco 7921 firmware version 1.0(3)
to CallManager |
|
|
Special number call is cancelled after 1
ring when keypad is locked |
|
|
Phone on Antiope vibrates if headset
attached when set vibrate alert |
|
|
User can not do factory reset if setting
access is disabled |
|
|
High multicast can degrade unicast RTP voice
quality |
|
|
75% battery icon appears with full battery |
|
|
7921 doesn't work with CME unicast paging |
|
|
Power consumption high after roaming during
a call with tspec enabled. |
|
4.1-Devpack
49 |
|
|
7937-Device Definition Files Need to be
Checked In |
|
4.1-Devpack
48 |
|
|
7937-Device Definition Files Need to be
Checked In |
|
|
7985 |
|
|
7985 Screen Powersave LED indicator can't be
distinguished from MWI |
|
|
7985 sources from random port rather than
from standard specified in olc |
|
|
7985 should use symmetrical UDP port numbers |
|
|
Visual call Pickup notification fails when
line audio alert setting off |
|
|
Visual Pickup Notification sometimes does
not overwrite status line |
|
|
7985 phone not working with Mobile Connect
service. (CMM/SNR) |
|
|
7985 does not send out video packets w/ IPMA
configured |
|
|
Star50 feature is not working on 7985 video
phone |
|
|
7985 phone with no voice vlan configured
fails DHCP/ip address. |
|
|
7985 enters reboot loop on upgrade when
using Alternate TFTP |
|
|
7985- the >> and delete softkeys in
edit dial screen arent working. |
|
|
7985- restart loop if load is different
between DHCP and alternate TFTP |
|
|
7985- Phone crashes when long input is
entered in inputboundary test. |
|
|
7985- Ringer stops riniging when try to
change ringer drg outgoing call |
|
|
Ringer stops when 2 incoming calls on 7985
& 1 call ended. |
|
|
7985- Phone dumps hex value on screen with
imageboundary service test. |
|
|
7985- IPMA - Manager screen goes off after
every change |
|
|
7985- Screensaver leaves chars all over
screen |
|
|
Ping replies from the phone are not recognized
by the originating host |
|
4.1
Devpack 47 |
|
|
7905/7912 |
|
|
CP7912-UK Locale files are downloaded every
time the phone reboots |
|
|
7912 increase number of digits displayed for
external phone number mask |
|
|
DTMF Tx failing 7912G |
|
|
7912G IP PhoneCannot access corporate
directory with French locale |
|
|
CP7905/7912 phoneDN returned Under
DeviceInformationX is Incorrect |
|
|
7912G does not boot up after firmware
upgrade |
|
|
CP7912G-The behavior after the recovery from
the DHCP issue |
|
|
Incorrect chunk size in http encoding for
StreamingStatisticsX |
|
|
HTTP URL requested by 7912 misses variable
name |
|
|
7912-Calling number is missing from received
call history |
|
|
The memory space of version string is smaller
than the macro definition |
|
|
7912 should retry after HTTP refresh failed |
|
|
7912 8.0(2) SCCP - phone resets when
accessing Corp Dir or other XML |
|
4.1-Devpack
46 |
|
|
Check in 7914 loads |
|
|
Add new icons for sidecar to support Muster
release |
|
4.1-Devpack
45 |
|
|
|
New phones - device definition files need to
be checked in |
||
|
4.1-Devpack
44 |
|
|
New phonesdevice definition files need to be
checked in |
|
4.1-Devpack 43 |
|
|
Adding THX and Babylon5 features |
|
|
7940/7960 |
|
|
Animated circle (reset icon) seen
continuously in a scenario |
|
|
Add new icons for sidecar to support Muster
release |
|
|
7960 not allow to select 2nd call of a
conference call on shared line |
|
|
A call picked up is not recorded in
'Received calls'. |
|
|
Upgrade LSC menu strings not flushed on
moving out of tht menu. |
|
|
7960 stops sending CDP packets - causes do1x
error disable switch port |
|
|
Phone remain in Configuring IP state even
with proper DHCP response |
|
|
Option 66 preferred over option 150 based on
appearance in DHCP ack. |
|
|
7960/40 skinny do not detect handset with
failover to SRST |
|
|
Unicode Special Characters blacked out on
7940 and 7960 SCCP phones |
|
|
Several call progress tones need to be
louder |
|
|
Secure Conferencing Icons for Muster |
|
|
7960 phone does not calculate srtp
authentication tag correctly |
|
|
Placed call list shows '*' for FAC enabled
calls |
|
|
Secure SCCP Phone Conference Initiator
Crashed on Hangup |
|
|
7940 ph does not accept new req after
rejecting invalid IP address req |
|
|
7960 SCCP does not play beep tone when DND
incoming alert is configured |
|
|
Phone temporary rejects HTTP connection when
its sockets are available |
|
|
Static, white noise heard w/ 7960 7940
logging into unity with G729 |
|
|
Update Cisco Logo on phone web pages |
|
|
Update the copyright year to 2007 on the
boot display for the mid-range |
|
|
7940/60 not streaming sometimes when using
encryption |
|
|
StreamingStatisticsX reports phone as idle
when call is active |
|
|
IP phone at remote offices stuck in opening.
|
|
4.1-Devpack 42 |
|
|
Checking in latest tone file for third
generation phones. |
|
|
6608 |
|
|
6608 MTP port intermittently unregistered |
|
|
6608 T1 CAS ports are getting marked as OOS |
|
|
6608- Cleanup code to make room for few more
fixes |
|
|
6608- debug enhancements |
|
|
6608 Gateway gets unregistered after
resetting MGCP Backhaul port 2428 |
|
|
7906/11/41 |
|
|
/61/70/71 |
|
|
Phone Directory gives incorrect details
after upgrade to 8.2.2 |
|
|
TNP- keyboard I/O errors on reset |
|
|
7970 phone in low power mode consumes more
power than CDP advertisement |
|
|
Phones failover to secondary node with wrong
cause code |
|
|
Network Locale Version backwards compatibility
|
|
|
Third gen phone may behave wrong under
stress registration test |
|
|
3g-phones -- pick up Sun Java patch to
address 2007 DST changes |
|
|
Hung RS-232 port causes phone
upgrade failure |
|
|
7971/7941 re-append parameters with a
redirected authentication |
|
|
7914 configured over 15 digit in line number
behaves very strange |
|
|
phone UI Locks up when adjust Speaker Volume
during registration w/ BLF |
|
|
third gen phones power is initally set high
power at boot w/line powered |
|
|
3rd gen phones running 8.0(4)SR1 unable to
adjust ringer after a call |
|
|
u7961/41/70 stuck at requesting after phones
inbound web access disabled |
|
|
PNG Broken- Phone fails HTTP GET if earlier
HTTP request is not finished |
|
|
After flash reformat phone gets flash
Programming failure errors |
|
|
Memory Leak on phones with repeated calls
with very short call hold time |
|
|
Pressing New Call should let user Enter
Number |
|
|
Bugtrap 0x91 phones (during fsck) |
|
|
Composed IPPM messages display + instead of
space |
|
|
Unknown name displayed if special characters
are in display name |
|
|
Exit softkey stops UI when in Security
Configuraiton/CTL File submenu |
|
|
TNP phones on CME can't resume call with
Line button |
|
|
make 'DEBUG' trace anticipated for a 1-way
audio problem as NOTICE trace |
|
|
Customer is experiencing one way audio calls
|
|
|
SenderJoins & Byes values were different
regardless of call status |
|
|
GUI stuck after changing contrast |
|
|
Osage- Phone drops incoming unicast EAPOL
when VVLAN is present |
|
|
Call duration timer window on ph display
cycles between multiple calls |
|
|
Idle sftkeys displayed on new incoming call
after transferw/rel image |
|
|
AutoObjInFocusIf.getLabel returns incorrect
information for a call item |
|
|
Response.Redirect fails |
|
|
Need to Press Right button twice on Nav Pad
to close Line Detail |
|
|
IP Phone SSH Vulnerability |
|
|
Filesystem Privilege Escalation |
|
|
Internal calls are having one way audio |
|
|
Filesystem Denial of Service |
|
|
OnHook Dialing from Line2 doesn't work if
Line1 and Line2 have same DN |
|
|
Phone doesn't calculate SRTP auth tag
correct for certain RTP payload |
|
|
Bug trap 91 if TCP server/client resides in
the phone |
|
|
Stutter Tone quality problem when using
speaker / line button |
|
|
Focus does not shift to off-hook line while
another call is incoming |
|
|
Focus should remain on oldest ringing call
with mulitple incoming calls |
|
|
Factory Reset require for secure phone to
move to another CCM |
|
|
IP-phones hang when call arrives while
XML-play in progress |
|
|
Phone displays CM down in a active call
during failback |
|
|
Large increase in PNG graphic processing
time |
|
|
7961 phone not show Help info for privacy
button |
|
|
No dial tone is heard after togglling the
hookswitch in ring out state |
|
|
Read linenumber from the config file |
|
|
Focus should remain on oldest ringing call
with mulitple incoming calls |
|
|
CallHistory Menu- line key, speaker key, no
longer work |
|
|
SIP Phone goes for a reset when proxy
address name starts with _ |
|
|
phone resets after warning out-of-chunks for
memory tracking |
|
|
Caller-id is not updated correctly for
conference calls |
|
|
Retrieving a parked conference call,
disconnects the call |
|
|
Phone crashed running Codenomicon SIP test
4913 |
|
|
unable to do cfwdall if kpml is enabled in
sip-srst mode |
|
|
SIP phone failed to clear Held call when CCM
restarted |
|
|
call tranfer after cfw noan on tnp sip phone
failed |
|
|
Incorrect Date header value in SIP REGISTER
request |
|
|
SIP Phone needs to also detect non-localized
Conference |
|
|
Number stored in missed calls not updated
upon receipt of SIP UPDATE |
|
|
Not able to Set CallFwdAll on tnp sip phone
in particular scenario |
|
|
TNP SIP sometimes sending malformed to or
from header |
|
|
7970 sip sends invalid presence subscription
causing high CPU |
|
|
Failed on multipl forward from SIP phone to
SCCP phones |
|
|
tnpsip phone doesn't light up blflamp when
destination press callfwdall |
|
|
Phone crashes when messages hard button is
hit. |
|
|
Call not forwarded after
CTINewCallAcceptTimeOut on SIP TNP phone |
|
4.1-Devpack
41 |
|
|
7936 Phone Displays Host not found when
accessing corporate directory |
|
4.1-Devpack
40 |
|
|
Check-in Cisco 7921 firmware version 1.0(2)
to CallManager |
|
4.1-Devpack 39 |
|
|
Need to change PTT URL to Application URL |
|
|
Install unconditionally Reinitializes
replication |
|
4.1-Devpack 38.1 |
|
|
Merging local dictionary in CCM |
|
|
Check-in 7921 firmware to CallManager |
|
4.1-Devpack 37 |
|
|
7935/7936 |
|
|
7935/6 reboot using corporate directory
search on 3'rd party LDAP server |
|
|
7936 with CCM 5.0 displays Server Not Found
when access Corporate Dir |
|
|
7936- Can gain access to web interface w/o
admin password |
|
|
7936 does not register G.729a capability
along with G.729 capability |
|
|
Selecting Tone Test and exiting hangs phone |
|
|
Setting up Admin VLAN id brings up the phone
without a DN |
|
|
7936/35- Ignore CDP V1 message for VLAN
configuration purposes |
|
|
7936 phone hangs when pressing hold &
resume |
|
|
7935 does not recover after power/network
loss |
|
|
7936 phone shouldn't release its VLAN until
the TTL(CDP message) expired |
|
|
UI displays Failed to set VLAN Idwhen
changing n/w setup in activecall |
|
|
When we dial the DN through web page
,message flashes for sec & proceeds |
|
|
7935 does not register G.729a capability
along with G.729 capability |
|
4.1-Devpack 36 |
|
|
missing 7906 default load 8.2(1) |
|
|
7985 |
|
|
Packets received on PC port are not
forwarded in some configurations |
|
|
7985 does not display animated icon w/ RTPRx |
|
|
Restart reason sometimes is not correct
under Network status |
|
|
Phone can rarely stop making calls after CCM
failover/failback |
|
|
Confrence List Remove feature does not work
on CCM 5.0 |
|
|
Invalid dialed number when dialed from
directory displays no information |
|
|
Exit softkey sometimes does not work on
Callback window |
|
|
Callback Notification window does not close
after Dial is pressed |
|
|
Phone sometimes does not fallback to the
correct Standby CCM |
|
|
Wrong display of softkey sets and callinfo
on IPMA assistant phone |
|
|
IPMA manager should not exit from IPMA
service w/ 1 assistant |
|
|
Phone did not register with the Call Manager
after a network power loss |
|
|
Phone unexpectedly reset during a long
duration H.263 call |
|
|
Some softkeys not work correctly with
CiscoIPPhoneInput object |
|
|
7985 phone not working with Mobile Connect
service. (CMM/SNR) |
|
|
7985 un-registers from the Call Manager
after the switch speed changed |
|
|
Network status should contain last restart
reason |
|
|
Hoot & Holler service does not display
Handset icon with RTP/Rx RTP/Tx |
|
|
Visual call Pickup notification fails when
line audio alert setting off |
|
|
7985- Ignore CDP V1 message for VLAN
configuration purposes |
|
|
Equation type input can have unexpected
delay when pressing numbers |
|
|
Pressing a number in Ring Tone menu works
differently than other phones |
|
|
There is no Call Status information
available via the web pages |
|
|
7985 appends devicename in HTTP request when
searching directory users |
|
|
Changing volume during the Hoot & Holler
service cause audio to be sent |
|
|
Hoot & Holler icon was not removed after
exiting the service |
|
|
Background image after download is obscured
by the image menu |
|
|
7985 can not handle URL with 255 char. |
|
|
PC Voice VLAN disabled does not work with
Admin VLAN |
|
|
IPPA phone service shows some unexpected
error messages when logging in |
|
4.1-Devpack 35 |
|
|
7911/7941/7961/ 7970/7971 |
|
|
Beep tone max power is only -22dBmO |
|
|
FSCK stuck in deadlock with syslogd |
|
|
DSP Configuration Files are not Correct |
|
|
Enumeration Pattern Code Updates |
|
|
Phone sends corrupted RFC2833 packets when
SRTP enabled for call |
|
|
Dev Studio changes to make building
Communicator easier |
|
|
Secure phone does not retrieve the SEP file |
|
|
7931- Call Plane Detail View is not open
after On-Hook dialing |
|
|
CiscoIPPhoneStatusFile LocationX parm not
used for small image size |
|
|
Commit of CSCef34402 broke c6slc, other?
pikespeak images |
|
|
Titan dsp host could 32-bit read between dsp
firmware two 16-bit writes |
|
|
Osage- Max Input Rxd msg displayed when 32
chars input to Shared Secret |
|
|
Power Save Configuration options missing in
Settings |
|
|
Osage- Status Messages for 802.1X
Authenticatio not as per Osage UI spec |
|
|
softkeys disappear after blind directory
transfer |
|
|
TNP- keyboard I/O errors on reset |
|
|
RTCP- Exiting Hoot & Holler cause phone
to send bogus BYE packet |
|
|
7931- Exception in OverviewModel during
restart |
|
|
Support G.722 56k and 48k in the Audio
Server |
|
|
TNP phone logs "Unable to get
memory" message on console |
|
|
pressing volume key then speaker button can
lock up phone |
|
|
G.722 K-Factor Table incorrect |
|
|
Highlighted Call isn't displayed if 10th
call ended leaving 9 held calls |
|
|
7970/7961- dtmf burst is played with a
double duration |
|
|
Phone does not send un-register message to
SRST on fallback to CCM |
|
|
7931- Pressing Line button does not change
Line focus |
|
|
Onhook dialing produces delay in feedback
sound with last digit |
|
|
IP phone fails to do HTTP authentication |
|
|
7931- Overview not in home position at
initial bootup |
|
|
RTCP socket open error may cause audioserver
to spin |
|
|
under is only 20 chars instead of 64 |
|
|
Dynamic Trace level registration results in
file create/delete operation |
|
|
EAP-Request/MD5 to PC supplicant could not
pass thru Gig phone |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
7961 phones not processing CTI request to
disable softkey |
|
|
TNP- dhcpRcv.c - uninitialized variable |
|
|
7970- Phone lock up when message URL has max
or 255 character |
|
|
IP Phone should re-DHCP immediately after
DHCP NAK |
|
|
7931- scroll up and down, sometimes a
leftover icon appear next to label |
|
|
show inventory command returns no data |
|
|
RTCP- SDES packets are not being padded
correctly |
|
|
Idle Prompt for SRST cannot be set back to
the default value |
|
|
Phone not sending DHCP traffic to pc port |
|
|
Unable to dial from external dir list after
cancel edit dial |
|
|
LCD display does not always show status of 3
consecutive lines |
|
|
7911G experiences loss of registration |
|
|
SIP phone show "Connected" in call
preservation if user in/out line disp |
|
|
7961 with voice vlan resets if IPC is
connected to 3rd vendor switch |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Ringing phone ICON keep showing up on the
phone display without call |
|
|
Skittles- Retain Dialplan from CCM while
failing over to SRST |
|
|
IP phone not direct HTTP request to proxy
server w/ unresolved DNS name |
|
|
Phone does not have "End Option"
field with DHCP Release message |
|
|
Incorrect DSP Configuration File Formats |
|
|
RTP Tx URI request should be rejected when a
call is active |
|
|
7931 won't autoscroll to previous line/call
in multiline scenarios |
|
|
3rd gen phones running 8.0(4)SR1 unable to
adjust ringer after a call |
|
|
When uri is not responded by user, second
uri post just hangs forever |
|
|
Clean up debug options available / messages |
|
|
Line DN label appear to be shifted a pixel
or two to the left on Display |
|
|
Digit tone improperly continues until call
connect |
|
|
JPN hone freeze at Cisco Logo after reset
due to Java OutOfMemory error. |
|
|
7961/70 fail to transfer a call with line 2
from Directory |
|
|
TNP- Remove NULL term from hostname in DHCP
request |
|
|
7971 displays "Ethernet
Disconnected" briefly |
|
|
Phone core dump when terminating mulitple calls |
|
|
phone not fallback to CCM and shows
"Restarting...". |
|
|
Enumeration Pattern Code Update |
|
|
Mute Button is enabled when Phone Speaker
Button throws Error pass Limit |
|
|
On turbo the overview is distorted when a
new call is created and ended. |
|
|
Osage- Transaction Status does not update
unless menu is re-entered |
|
|
TNP SIP phone uses wrong default TLS port
number |
|
|
Handsfree Receive Frequency Response does
not meet the mask |
|
|
debugsh- set LOG_DEBUG trace level for
sunvm.cnuw/ debug SIP/JVM command |
|
|
Phone does not detect Invalid Load Server IP
address for "A.B.C D" |
|
|
Phone Ringsin Continuously,Need to power
off/on to clear the call |
|
|
7911 SLR is 5 dB softer than required, its
ok in GL mode |
|
|
IPPM- Phone displays XML Parse Error when
accessing Contact List |
|
|
7961 - PC cannot see data traffic if PC
Voice VLAN Access is disabled |
|
|
TNP SIP phone can not handle long Unicode
callid/linetext |
|
|
7931- Clean up OverviewModel
ACTIVATE_REQUEST event handler |
|
|
Osage- Phone drops incoming unicast EAPOL
when VVLAN is present |
|
|
7970 Runs out of memory as phone when idle
URL is used |
|
|
7931- Phone looses softkeys when exit from
IDLE URL screen |
|
|
Incorrect values in RX/TX_START_TIME and/or
REPORT_TIME pegs |
|
|
TNP phones on CME can't resume call with
Line button |
|
|
Focus does not shift to off-hook line while another
call is incoming |
|
|
Soft factory reset does not clean files from
/etc/sfr.tab |
|
|
RTCP- With RTCP disabled web StreamingStats
Report Times are invalid |
|
|
Include Kernel.core into the sylog files for
debug purpose |
|
|
Not able to use Dial Sofkey in Corporate
Directory |
|
|
TCP not sending all posted data after socket
close |
|
|
7911/41/61/70/71 - 2 concurrent XML posts
result in Error 0 or Error 6 |
|
|
devoplement build (TNP) script does not work |
|
|
Dial Softkey should be disabled for
corporate directory/PAB/FastDials |
|
|
Turbo- DoS tool icmpsic crahses phone on
Bugtrap 0x93 |
|
|
offhook w/ handset for the first time after
reboot, no dialtone is heard |
|
|
Unmount Error |
|
|
HTTP sessions are not currently aged-out |
|
|
CreateStringMatchProperty does not update
the allowedValues |
|
|
TNP - 7911 phone needs an 802.1X port lookup
mechanism |
|
|
9 lines with call in Hold Reversion, phone
stops ringing |
|
|
provide for next generation static analysis
for TNP |
|
|
RTCP- BYE packet has padding bit mistakenly
set |
|
|
7941/7961/7970/7971 Aliasing in high band
when using wideband headset |
|
|
7931- LineFullDisplay detail is missing from
the title |
|
|
Call History Enhancements for Chumbawamba
Phase 1 |
|
|
7970- reduce msg sizes being used in network
daemon IPC |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
When calls are selected/unselected, sorting
is done immediately |
|
|
TNP - 7971G-GE forwards 802.1X packets twice |
|
|
Exit softkey stops UI when in Security
Configuraiton/CTL File submenu |
|
|
7931- May have a Java Memory leak in
disposeDynamicFeature |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
IP phone stuck at Cisco Logo screen when
reset from CCM w/ sidecar |
|
|
Can not login to phone during automation
testing |
|
|
Network Locale Version backwards
compatibility |
|
|
support persistent status line display on
SIP phone in SRST mode |
|
|
Phone throws exception upon going off-hook |
|
|
Dial URI w/ Active Call doesn't Invoke Call
Options when no app in focus |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
7931 Titles in Line FullDisplay aren't left
aligned at at the same place |
|
|
Phone continues to ring after shared line
picks up a transfered call |
|
|
mipspacker not use CNU versioning for BN2
image |
|
|
7931- Line number overlayed with ellipses
... while in active call |
|
|
7970 SCCP requires Authorization when
hitting **# to unlock the phone |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Phone Service unavailability message
corrupted |
|
|
UDI Time Zone not displaying string from
phone config file |
|
|
7931- Handsfree RLR does not meet the spec |
|
|
Phone not showing "Duplicate IP
Adress" in status line |
|
|
HOST Field Send IP Address Instead of
Defined Hostname |
|
|
7911 Phone speed and duplex settings not
saved |
|
|
CP-7971 does not cache TFTP address if
option 66 set TFTP server name. |
|
|
TNP phone sends
StationSubscriptionStatReqMessage at restart |
|
|
Focus changes to the new ringing call before
10 secs.. |
|
|
Reset on sleep mode phone would not put it
back to sleep mode |
|
|
CiscoIPPhoneDirectory/DirectoryEntry/Name
should be restricted to 32 cha |
|
|
TNP- check return value when writing
dhcp.conf |
|
|
Remote in use calls with no caller ID should
display "To Unknown Number" |
|
|
Sanity- Core produced for rtsp on
restriciting incoming bandwidth/bitrat |
|
|
Fragile file cleanup and performance
enhancements (Jasmine featurette) |
|
|
7931- Tuk Tuk noise heard while using
wideband codec for a call |
|
|
7970 Phones have incorrect active display
during shared line call |
|
|
SIP phone should reattempt download of
softkey&dp on TFTP down/ timeout |
|
|
For Cbarge "CM down,features
disabled" message not displaying on 7970 |
|
|
7931- Headset icon not displayed when
Headset LED is pressed |
|
|
Expand Directory object name field to accept
64 characters |
|
|
7931- Softkeys disappear with 4 sofkey
templates |
|
|
7971 should set Audio Preference to default
values after Erase |
|
|
Muffled voice on receive for some calls |
|
|
cnu recover second look |
|
|
7911- GroupPickUp does not work |
|
|
Unknown name displayed if special characters
are in display name |
|
|
7970-DHCP- Rejects DHCP request with option
15 from CNR |
|
|
Display on shared-lines not-in-call is not
consistent in cBarge scenario |
|
|
7931- Incorrect call appearance on shared
trunk monitor calls. |
|
|
Call Focus shifts to Held call for
consultative conference call leg |
|
|
TNP - Soft factory reset should clear 802.1X
PAE info |
|
|
7931- Enable video support |
|
|
Focus is on wrong call when line view is
opened indirectly |
|
|
Change the 7906 BN2 to use RELEASE keys for
pilot build |
|
|
Turbo should not advertise G.722 |
|
|
Dynamic features like BLF Speed dial and
Privacy are not working |
|
|
Call fails when no dialplan and registered
to SRST |
|
|
Conference on Alerting with 8-0-2-4S load |
|
|
Update 7911 diagnostics to version
10.02.00.06 |
|
|
CNU kernel BugTrap 0x91 with V-E-R-Y
specific conditions |
|
|
TNP phone stuck in blank screen during
upgrade to 8.0(3) load |
|
|
third-gen phone 8.2(1) recover process is
not displayed |
|
|
dsp ingress frame timestamp not following
RTP RFC3550 |
|
|
sleep() system call not POSIX compliant |
|
|
AbbrDial key shouldnot be active when
speakerbutton is disabled |
|
|
Text Item Displays are not right justified
in RTL locales |
|
|
Phone should explicitly turn on display when
reset/lost registration |
|
|
SIP phones should Ignore unknown softkey set
names in softkey xml |
|
|
7931- Add icons to the DetailsFullDisplay |
|
|
CIA-680 Support on 3rd gen phones |
|
|
revertPriority setting not used for 1st call
after changing the setting |
|
|
Third-Gen phones running 8.0(3) do not hear
multicast audio from RTPMRx |
|
|
8.2 phone load causes robotic issue at
customer site |
|
|
Dialplan is not supported when Failover to
SRST |
|
|
Highband noise reduction tuning |
|
|
Bugtrap 0x91 phones (during fsck) |
|
|
unable to disable kpml on TNP phone
registered to CME |
|
|
TNP- send DISCOVERs if no DHCP server can be
found |
|
|
IP phone reset with DOS attack |
|
|
7941/61 LCD controller must be reset at
startup time. |
|
|
Arabic locale missed QRT on dest info |
|
|
Empty Dial list is getting displayed on
phone |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Default router entry removed when dup ip
present |
|
|
Can not press line 36 on 7970 with 2
sidecars |
|
|
7931- Unable to answer call on 2nd line
using phone handset |
|
|
"On " prompt doesn't always work |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
TNP- "show inventory" CLI output
not adhering to the specificication |
|
|
redial sk is not active in onhook state |
|
|
getEndPointInfo reports MWI setting
incorrectly |
|
|
vm -mem broken on Broadcomm platform
(7941/61, 7970/71) 8-2-0-20 |
|
|
LCD display shows status of Lines 22-24
after phone boots up not 1-3 |
|
|
Turbo- DHCP recv socket error on bad address |
|
|
SenderJoins & Byes values were different
regardless of call status |
|
|
Osage- 7961GE stops receiving EAP-Req/ID
during long duration reset test |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
7931- Doesn't show IDLE display on phone
display after restart from CME |
|
|
TNP phone fails to display the switch info
at its webpage |
|
|
7970-PNG image file download crashes the
phone |
|
|
SYN ACK messages from phone not DSCP tagged |
|
|
Jphone- Navigate problem under network
statistics menu when debug mode |
|
|
make property retrieval from RMS store file
effecient |
|
|
Handsfree SLR does not meet the spec |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Add volume control for local and network
tone |
|
|
7931- Speed dial does not display called-id
when another line offhook |
|
|
Selective graying out of AudioPref menu
items incorrect on inline power |
|
|
Need to Press Right button twice on Nav Pad
to close Line Detail |
|
|
Placed calls are not multi-party and should
not show a MP call history |
|
|
Phone Continuously displays
"Requesting...". |
|
|
Softkey wrong after fallback from SRST |
|
|
7961 (and 7941,7970,7971) doesn't display
Call park number after getting |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
7931-UI shows lines 22-24 when line button
pressed with AppMenu Open |
|
|
Settings -> Device Configuration -> UI
Configuration menu is missing |
|
|
Call History Lists inaccessible after having
max entries and deleting 1 |
|
|
7931- Phone restart from CM duration test
leads to Disk full |
|
|
Add SIP related changes to support G722 for
ph0 of wide world |
|
|
Missing Pixels on the left side of UI
displays on Turbo phones |
|
|
phones should not advertise Voice VLAN on PC
port |
|
|
JTest- SIPCCAdapter.java switch statement
missing breaks |
|
|
7931- Factory Reset Walk LED pattern is only
16 |
|
|
7971 phone reverts to old config after
changes saved to netwk config |
|
|
7931- LEDs for lines above 8 do not
illuminate |
|
|
debugsh should support RTCP trace |
|
|
Cfwdall fails to come back on CCM after
fallback from SRST |
|
|
7914 displays old version of remote-in-use
icon |
|
|
Line LED not lighting up or delayed on
incoming calls |
|
|
Phone display not turned on when going into
reverting state |
|
|
TNP SIP Phone resets after auto register due
to default load info missin |
|
|
PNG Broken- Phone fails HTTP GET if earlier
HTTP request is not finished |
|
|
Pushing RTPRx or RTPMRx URI to phone in a
call enables mute |
|
|
Call Statistics menu- Sender size is not a
correct format |
|
|
SIP phone UI Locks up and Keypresses ignored
(still registered w/ CCM) |
|
|
UI locks up & phone cannot register |
|
|
Timer Exception seen in TimeDateRequest |
|
|
Clear softkey does not work in Status
messages screen |
|
|
Outgoing ringing and incoming ringing tones
played at same time |
|
|
apply patch for Diab compiler from WindRiver |
|
|
Add new tone messages to make
traditional/stutter tones selectable |
|
|
Phone accepting duplicate IP |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
7911, 7906,7931 & 7921 have poor voice
quality with G711alaw codec |
|
|
Out of Memory - Connection refused errors
after duration testing |
|
|
Turbo- 1st incoming call can't be answer if
2nd one be connected first |
|
|
RTCP- RR/SR packet is missing some info when
there is 2 report blocks |
|
|
SIP gives different Error message than SCCP
in Locations scenario |
|
|
7931- IDLE URL Refresh timer doesn't work in
66DEV image |
|
|
Shared line display & going offhook
while in active call distort display |
|
|
Write to the TNETV105x PCNTRL "Access
Control Reg" must be 16 bit |
|
|
TNP- libcso.map from build should be saved |
|
|
New Features - Auto Call Select and More Key
Timer |
|
|
7931- Leave 1 pixel space w.r.t. App
Menu/Headset/etc |
|
|
Line reports as unregistered, but it's not,
after failover |
|
|
Re-sync tone table if dsp host re-starts |
|
|
Phone core dump while running the call
features automation script |
|
|
Phone not retrying the re-IP after dup IP |
|
|
7961/41 Speaker LED on even after pushing
End key |
|
|
SETTINGS softkey does not work if no DHCP
server available during bootup |
|
|
mount command exiting with status code 64 |
|
|
KATE Input causes NPE and non-password data
while using XML services |
|
|
u7961/41/70 stuck at requesting after phones
inbound web access disabled |
|
|
SCCP phone does not register back to
publisher after restart. |
|
|
Need an API to assign a local port to TLS
connect |
|
|
LineModel dispose call throwing a
ClassCastException |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Dialer does not close correctly after Cancel
or Idle Timer Expires |
|
|
Need filter coeficients for headset, handset
and speakerphone |
|
|
TNP Phone 7941 second line line button will
light up for incoming call. |
|
|
Static Analysis Codebase Cleaning on Select
Files |
|
|
Multi-Party Call History - Transfer case -
Received call "from" details |
|
|
Audio Server K-Factor table for G.722 |
|
|
CNU Flash Filesystem not recoverable if it
fills up |
|
|
certcnu.bin failure- GETCNU- CNU
image update failure; code = 10 |
|
|
Status of BLF SpeedDial does not get
updated. |
|
|
need feature parity between sip and sccp
phone for speed-dial |
|
|
Endcall softkey doesn't work in Call
Preservation |
|
|
Answer and DnD Softkeys are not always
displayed when a call is rcvd |
|
|
Idle sftkeys displayed on new incoming call
after transferw/rel image |
|
|
softkey disappears on the phone after
several calls are made |
|
|
7970 precedence call waiting tone does not
stop |
|
|
Issue with Pegs when the call is remotely
held and on MOH |
|
|
wrong filepath used after posting a TFTP
file |
|
|
Phone should send the 433 Anonymity
Disallowed for anonymous calls |
|
|
Diagnostic is alway reloaded into the
primary slot |
|
|
Turbo- Speed dial entries not at designated
position |
|
|
Calling/Called Info not correct for SIP TNP
phones |
|
|
Double call sort after ending selected call |
|
4.1-Devpack 34 |
|
|
Adding 8.2(1) features to CCM 3.3, 4.1, 4.2,
5.0 |
|
4.1-Devpack 33 |
|
|
NewCall and EndCall should not be mandatory
softkeys |
|
|
7921 |
|
|
Need update to "devicelistx.asp"
to support new Cisco 7921 wireless phone |
|
4.1-Devpack 32.1 |
|
|
Update 7921 CSV and XML files for FCS |
|
|
7920 |
|
|
7920 3.0.1 FIrmware and XML Schema Check In |
|
4.1-Devpack 31 |
|
|
Unable to insert 7941 phone with Device
Security Mode as Authentication |
|
|
CCM4.1(3)ES. SQL error when inserting a 7961
phone |
|
|
Add support for Security feature in
Communicator |
|
|
3.0.1 English Dictionary Check In |
|
|
Link 'View the User Guide for your phone'
not available for 7961/7941 |
|
|
6608 E1/T1 |
|
|
6608 T1 cas channel rejects outbound call |
|
4.1-Devpack 30.4 |
|
|
CCM4.1(3)ES. SQL error when inserting a 7961
phone |
|
4.1-Devpack 30.3 |
|
|
CCM4.1(3)ES. SQL error when inserting a 7961
phone |
|
|
7902/7905/7912 |
|
|
Phone response status inconsistent between
models |
|
|
7912 phone should not send
StationFeatureStatReq if feature is not confi |
|
|
7905Japanese characters are shown as ?s in
EM screens |
|
|
CP-7912 can not use 255 as last octet of
SRST address. |
|
|
IPICS Channel selection by select key does
not work intermittently |
|
|
DnD fails on 7912s |
|
|
7912 w/alt tftp disabled does not read TFTP
server from DHCP |
|
|
7912 can not resume multiple calls from hold |
|
|
Connection Monitor Duration changes not
applied to 7902 |
|
|
7912 cannot make new call after lisfting
handset |
|
|
Malformed XML Delieverd from 7912GA when
using DeviceInformationX |
|
|
No response to UserToDeviceData for Key: xxx
URI passed from CTI |
|
|
Init: CallHistory URI does not re-set status
line on 7905 |
|
|
call waiting tone doesn't stop when the
second call hangs up. |
|
|
7912 prefixes fastdial with 'undefined' |
|
|
7912 affected by ARP storm |
|
|
7912 authentication problem - password
encoding |
|
|
IP Phone Service problem with 7912 http
redirect v8.0 |
|
|
Able to Change Ring Volume Even when Setting
Access set to Disable |
|
|
7912G-A phone does not obtain address when
voice vlan = access vlan |
|
|
CIA 650: Randomize TimeDateReq's to Call
Manager from 7905/7912 |
|
4.1-Devpack 30.2 |
|
|
No web access cfg option for 7941/61 in CCM
device configuration page |
|
4.1-Devpack 30.1 |
|
|
Unable to insert 7941 phone with Device
Security Mode as Authentication |
|
4.1-Devpack 30.0 |
|
|
Update 7921 CSV file to add Prefer Alternate
Script option |
|
|
7940/7960 |
|
|
Build phone loads |
|
|
JPN-Cancel softkey not available for configuring
7960+7914 |
|
|
phone displays Select Ringer... for Invalid
DistinctiveRing.xml |
|
|
UI screen is grayed out when i-button is
pressed |
|
|
Autodial cancelled is shown for a Phone in
RingIn state |
|
|
Phone displays AutoDial Cancel in transfer
scenario |
|
|
7960 tries fallback to CCM that has CCM
service shut but port 2000 open |
|
|
Phone Softkey should be greyed out for
Disable Speakerphone and Headset. |
|
|
7960 produces garbled audio and repeated
words for PA Help |
|
|
Softkeys within various Settings submenu not
responding if held |
|
|
DN not displayed in a hold scenario after
line button press. |
|
|
Init-CallHistory URI does not re-set status
line on 7960/7905 |
|
|
Phone displays Callmanager parameter as
UNDEFINED to boot up process |
|
|
revertPriority = Even fails when Hold
Reversion call is oldest |
|
|
Integrate DSP rev 4.0(2) |
|
|
parked calls get loud tone when picked up
from 7960/40 on CME 4.0 |
|
|
Callback can not be activated for a busy
extension |
|
|
Abbreviate dialing should not be available
if phone not able to call |
|
|
need to press line button twice to answer an
incoming call |
|
|
Mute light stays on after audio broadcast is
complete |
|
|
ST- 7960 secure phone got TLS error with
SRST after CCM 4.2.2 upgrade |
|
|
one way voice when the timestamp field in
the RTP packets rolls back |
|
|
RTP Tx URI request should be rejected when a
call is active |
|
|
7960 does not differentiate local hold call
and remote hold call |
|
|
40/60 - LA dev size grown above acceptable
size limit |
|
|
7960 with voice vlan resets if IPC is
connected to 3rd vendor switch |
|
|
phone doesn't handle the DHCP next server
field and option 66 correctly |
|
|
7960 displays XML error on hitting
directories button with French locale |
|
|
Phone hangs with HIGH CPU detected- during
EM logout & locales installed |
|
|
6608 |
|
|
6608 PRI Gateway stayed up even when CCM
lost connection |
|
|
6608 shows wrong OID |
|
4.1-Devpack 29.7 |
|
|
6608 PRI Gateway stayed up even when CCM
lost connection |
|
|
Link 'View the User Guide for your phone'
not available for 7961/7941 |
|
|
7935/7936 |
|
|
Phone Button does not work |
|
|
7936 with 4.2SR1 cannot dial digits when in
call state 3 (Ring Out) |
|
|
Scrolling to the end of the line in EditDial
causes 7935/7936 Reboot |
|
|
7936 not passing DTMF while in alerting
state. |
|
|
DTMF tone will not play for consecutive same
digits with 7936 |
|
|
Display is not uniform when dialing an non
existing number |
|
|
Mute dosen't work with Ping when CCM fails
over |
|
|
Phone dosen't ring while viewing the MAC
address details using **6 |
|
|
7935 and 7936 do not support 40, 50, and
60ms frame sizes |
|
|
Phone displays In Use Remotely with out
shared line in SRST mode |
|
|
LED Status changes when the Transfer softkey
is selected in SRST mode |
|
|
7935/36 need to support the priority field
in DisplayPriNotify message |
|
|
Polycom 7936 doesn't refresh after saving
the Alt TFTP address |
|
|
Main/Secondary TFTP Address cannot be
modified when DHCP is disabled |
|
|
Conference not working on 7936 in SRST mode |
|
|
7936 Phone does n't allow/display full
domain name. |
|
|
7936/7935 does not support JOIN feature of
CCM 4.0 |
|
|
Renumber 7935 firmware load name to match
the CCO versioning |
|
4.1-Devpack 29.6 |
|
|
6608 T1/E1 |
|
|
6608 PRI Gateway stayed up even when CCM
lost connection |
|
|
MGCP backual message with length of 12 bytes |
|
|
Router identify a very short DTMF as a valid
DTMF |
|
4.1-Devpack 29.5 |
|
|
Add support for Security feature in
Communicator |
|
4.1-Devpack 29.4 |
|
|
Merging local dictionary in CCM |
|
4.1-Devpack 29.3 |
|
|
Jphone software changes to address Memorex
enhancements in EDCS-505798 |
|
|
Support RTCP featurette |
|
|
New Features - Auto Call Select and More Key
Timer |
|
|
Add nightlight features |
|
4.1-Devpack 29.2 |
|
|
Add 7921 support files (CSV, XML, GIF) to
CCM |
|
4.1-Devpack 29.1 |
|
|
7985 |
|
|
Phone ignores DHCP option 150 when option 66
is present for TFTP server |
|
4.1-Devpack 29 |
|
|
7914 |
|
|
Implement SeaDragon features |
|
|
7940/7960 |
|
|
7960 phone does not clear status line during
reset |
|
|
pressing line button on ipphone doesn't
switch between detail &overview |
|
|
Posting Line34 URI enables Line30 on ip
phone. |
|
|
7960- Does not preserve the state of
mute/spkr button in handset mode |
|
|
7960 drops the incoming call when using the
IPICS services. |
|
|
7960 phone does not handle HTTP code 401 for
push request |
|
|
Phone- Authentication username/password
takes only 31 characters |
|
|
CiscoIPPhoneInput takes * and # when input
is set to N |
|
|
StreamingStatisticsX not backwards
compatible |
|
|
7960- Call being on hold is NOT sorted by
Select function |
|
|
7960- Doesn't update CDP cache when no voice
vlan present in CDP message |
|
|
7960 DSP Logging utility broken |
|
|
7960 does not display via XSI Object Pass
through |
|
|
IP reassembly broken |
|
|
IP phones become unregistered from both SRST
and CM |
|
|
7960/7940 phone stuck at CONFIG IP after a
reset/power cycle |
|
|
Phone load Upgrade to 7.2(3) causes RXshort
errors on PC port |
|
|
Phone drops untagged PC Traffic |
|
|
HTTP 100 Continue from phone malformed |
|
|
Remove use of linked directory in SCCP BA |
|
|
7960 - XML Debug PUSH behaves erratically |
|
|
Handle Current Call missing when dialing
from Directory |
|
|
Phone rejects menu responses from server-
Fastdial, Corp Dir |
|
|
Callback notif (Dial) & Park while
already in an active call fails. |
|
|
GARP enable/disable ignored |
|
|
The phone crashes when it receives invalid
Response.ContentType in HTTP |
|
|
Secure Phones does n't cancel tftp request
while cancel key is pressed |
|
|
7940/60 PC port 100M does not receive
network traffic intermittently |
|
|
7960/7940 Rcvr Lost Pkt reports as a
negative no under impairement |
|
|
Unable to dial the CB notified number during
ringing state |
|
|
No sidetone during first phone call
following phone registration |
|
|
Phone performs unneeded ARP when Garp
enabled |
|
|
Phone removes ARP entries too quickly |
|
|
help for settings button not displayed when
setting key is disabled. |
|
|
DHCP enabled Phone resets with held call
when alternateTFTP changed |
|
|
Phone doesn't display held call in detail
view when barged call ends |
|
|
Promts is Truncated to 20 Characters when
using Greek Locale |
|
|
Phone resets if we dial Half of the DN
on-hook & remaining off-hook |
|
|
Speed dial from Monitor DN is not working
with 7.2.2 |
|
|
phone display Remote-In-Use menu when the
other end resume the call |
|
|
DIALED Number missing in CFA where the target
phone is 7940/60 SCCP |
|
|
Update 7960 built-in font to include new
zero with a slash |
|
|
7960/40 cannot register in autheticated mode
CCM 4.1.X OS 2000.4.2 |
|
|
Phone resets during high bandwidth traffic
to PC |
|
|
Placed calls are recorded on all shared line
phones |
|
|
Missing SpeedDials on phone after upgrading
the phoneload |
|
|
7960 crashes when more than 20 calls placed
via stress script |
|
|
Placed call list under directory gets
updated only for Connected calls |
|
|
7960- Unable to reset phone when other
shared line is busy |
|
|
Phone strip dialed Number in Directory
Placed call list for PSTN call |
|
|
7985 |
|
|
The phone does not honor the Connection
Monitor Duration fallback value |
|
|
Phone may malfunction if more than two lines
configured. |
|
|
Telnet xstatus command under DNS/Domain Name
contains non-ascii letters |
|
|
Need to add support for IP phone service |
|
|
IPMA is not supported with 7985 video phone |
|
|
Add screen saver to 7985 |
|
|
XML support |
|
|
Three or more line appearance needed |
|
|
Ocius should have a contrast and white
balance configuration options |
|
|
save button placement cause user to end call |
|
|
Directories menu does not display for 15
seconds when URL is unavailable |
|
|
Background image support is required |
|
|
Phone crashed when 100 calls active and
remote side is lost |
|
|
7985 does not play the MLPP premption tone |
|
|
Settings Erase softkey is displayed even
when config is locked |
|
|
7985 video endpoints do not support
services. |
|
|
Packets from the PC port are not being
forwarded out SW port |
|
|
7985 crashed when attempting to originate a
call from WebDialer |
|
|
Phone does not ring at all if the selected
ring tone is not available |
|
|
Error message on missing ring tone is
different than 7970 |
|
|
Phone never boots up when background image
is changed |
|
|
Phone does not detect changes to the CM
background image list file |
|
|
7985 does not do Authentication for
CiscoIPExecute |
|
|
7985- HTTP redirect not work |
|
|
7985- CiscpIPPhoneIconMenu oject parse error |
|
|
7985- HTTP refresh not work |
|
|
7985- two items missing from phone's web
access page |
|
|
7985 not display Authentication URL on
Device Configuraiton menu |
|
|
7985 should have Power Save Configuration
menu |
|
|
Device ID in CDP messages should all be in
upper case |
|
|
7985 takes too long to re-register when
image load is not found |
|
|
7985 not back to power save mode if
restarted from CCM |
|
|
Alpha Numeric fields use different key
mappings than other phones |
|
|
7985 not back to power save mode after a
call coming in |
|
|
7985- phase 2 image does not support asp URL
pushed to the phone |
|
|
7985 should exit Service app after login w/
ExtensionMobility |
|
|
7985 (X) button toggles between Full Screen
and Overlay modes |
|
|
7985 only shows 6 lines w/ Privacy and
Speedial configured |
|
|
7985 does not display To conference at line
button menu |
|
|
Callback activation tone is not heard when
using TFTP Server 2 |
|
|
7985 not registered to its CCMs |
|
|
7985 not update call status icon at line
button menu |
|
|
Hanging up the phone does not work when
failover occurs during call |
|
|
7985 crash when Execute Object is pushed to
phone with proxy config |
|
|
7985 got authentication error |
|
|
7985 can not list PAB entry |
|
|
7985 displays white line at full screen |
|
|
7985 does not send out video packets w/ IPMA
configured |
|
|
There is no Cancel softkey when requesting a
phone service |
|
|
Berbee services do not work on 7985 |
|
|
Softkeys in the Berbee phone service do not
work properly |
|
|
MyGroup IP service returns back John
Chambers' group instead |
|
|
7985 should exit from Setting menu by
pressing Setting button |
|
|
7985 Error message different when URL DNS
name error |
|
|
7985 crash when wake up from power save mode |
|
|
7985 incorrect behavior when get HTTP Error
404 |
|
|
Camera Properties need a wider range of
changes |
|
|
When upgrading the software the status line
is stuck |
|
|
Left/Right arrows should change the monitor
brightness values |
|
|
7985 could not display FastDial page |
|
|
7985 Update at service page does not work |
|
|
Phone crashed while looking at the eventlog
during an active call |
|
|
Video between 7985s momentarily blurs out |
|
|
7985 crashs while answering a call |
|
|
Remote side video stops working when
hold/resume rapidly pressed |
|
|
7985 should close the listening chanel when
service app is closed |
|
|
Exit an IP phone service returns the user to
the top of the service list |
|
|
Phone takes DHCP option 150 in the wrong
order |
|
|
Conference call info status is displayed as
the the 4 instead |
|
|
Digits after first call state softkeys are
messed up |
|
|
Calls for status line is corrupted after
pressing directories button |
|
|
The From status line displays no number on
an incoming call |
|
|
Call Park doesn't display the number parked
at |
|
|
Phone should drop from full screen mode
during an incoming call |
|
|
7985 Push Execute failed with Internal Error |
|
|
7985 crash w/ call on hold |
|
|
7985 does not disable SSH after reset |
|
|
985 fails over to SRST after ethernet cable
replugged in |
|
|
7985 does not change Camera properties back
to default value |
|
|
7985 should not display Erase key at
CameraSettings menu |
|
|
7985 plays wrong Ring Tone |
|
|
7985 does not save selected Ring Tone if
RingList.xml not available |
|
|
HELP ID- Help for Camera Settings returns
help for Monitor Brightness |
|
|
HELP ID- Brightness Hue Saturation help
returns main help topics instead |
|
|
7985 set button template wrong w/ one button
set as None |
|
|
7985 crash when access Help Main menu |
|
|
7985 fails to display Video Mute icon when
incoming call answered |
|
|
Video mute line status icon is lost after a
hold/resume |
|
|
Placed Calls Directory entries have a %s as
part of the display |
|
|
Background & Ring don't reset when
Restore Default Settings is involked |
|
|
Downloaded Background & Ring list
missing when TFTP Server 1 is down |
|
|
7985 crash when Line key pressed on Help
Menu |
|
|
X button does not work in Service w/ Host
Not Found Error |
|
|
No Help Info for Transfer softkey |
|
|
No Help Info for NewCall softkey |
|
|
No Help Info for More softkey in onhook
state |
|
|
No Help info for Dial and Cancel softkeys in
onhook dialing state |
|
|
No Help Info for NewCall sofktey in
Remote-In-Use mode |
|
|
Softkey sets mess up after access Help in
Callback mode |
|
|
No Help info for ImmDV and TrnVM softkey in
ringin state |
|
|
7985 should include Camera Setting info on
View Setting menu |
|
|
Forwarded to status message not display the
DN |
|
|
7985 displays ?1001 status message when in
Setting menu |
|
|
X New Missed Calls should not persist w/ new
incoming call |
|
|
7985 does not support Restricted Setting
Access |
|
|
Phone crashed pressing the Search softkey on
Corporate Directory |
|
|
Next softkey does not work in Corporate
Directory |
|
|
Wrong softkeys when looking at an empty
Missed Calls list |
|
|
Cancel softkey has no impact while
downloading Background images |
|
|
7985 play ringer to handset for a second
call |
|
|
Softkeys disabled after change audio source
w/ Handset off the crack |
|
|
Forwarded Call Infomation Display not as
configured |
|
|
Softkey sets changed after pressing Line
button |
|
|
7985 should switch back to the first call
after 2nd disconnected |
|
|
7985 behavior inconsistant with 2nd incoming
call |
|
|
Wrong softkey sets for barged call |
|
|
7985 displays Remote-In-Use icon after barge
into a call |
|
|
First ring tone in ring tone list is the
letter a |
|
|
Cannot easily answer incoming call while in
Missed Calls Directory menu |
|
|
7985 call status message mess up for shared
line |
|
|
7985 shared line Call Info display different
from other phones |
|
|
7985 should initiate a new call on shared
line by selecting the line |
|
|
7985 not show the CallInfo of shared line on
line menu |
|
|
Dial key not work on FastDial |
|
|
7985 should always use first avail. line for
Dial from Directory |
|
|
7985 should allow number with 25 digits at
PAB |
|
|
7985 not fallback to primary CCM if the CCM
restarted |
|
|
7985 does not have Next Softkey at Berbee
main menu |
|
|
No Update softkey for graphicMenu and image |
|
|
7985 not work with directory.asp |
|
|
7985 fails to display No Park Number
Available |
|
|
PAB service URL does not work |
|
|
ExtensionMobility ServiceURL button not work |
|
|
IP Phone service - My Group does not work
properly |
|
|
7985 flash light not blinking for Callback |
|
|
Denial of Service tcpsic script crashes the
7985 |
|
|
Personal Address Book edit Name returns 400-
Bad Request |
|
|
7985 not display Softkeys with position more
than 5 |
|
|
7985 could not display Directory object with
maximium value |
|
|
7985 crash when pressing Softkey-Next and
Softkey-OK |
|
|
Phone does not recoginize
SoftKeyItem/Position object |
|
|
7985 gives parsing error with IP Phone Agent
Service |
|
|
7985 crashed when running a image slide show
IP service for 10 minutes |
|
|
Fast Dial phone service should be allowed to
Assign up to 32 digits |
|
|
Call Information is not displayed after
pressing Settings button twice |
|
|
7985 gives incorrect Error Code for XML
parsing error |
|
|
Phone help does not work |
|
|
7985 gives ParseError if IPMA realtime
update stopped |
|
|
7985 crash when press Exit at IPMA assistant
service |
|
|
7985 does not display Exit key w/ Parsing
Error |
|
|
Phone does not fallback off SRST router
after call is terminated |
|
|
7985 crashes when attacked with some Denial
of Service scripts |
|
|
Phone displays a ? instead of line feed on
directory listing output |
|
|
Blackjack IP phone service returns error after
1st key press |
|
|
IPPA service Agent Login screen password
entry is displayed in the clear |
|
|
Phone directs some http requests to the
proxy url when it should not |
|
|
PC Voice VLAN disabled does not work |
|
|
Line button not work if not all line buttons
are assigned |
|
|
7985 should change focus to the active call
after exit from Setting menu |
|
|
No Help ID for IPMA related softkeys |
|
|
Softkeys are confusing when in the Lines
menu |
|
|
Cannot hang up a call when the call comes
from a shared line |
|
|
IPPA service briefly displays some XML code
during start or state change |
|
|
7985 crash with broadcast traffic at Voice
Vlan |
|
|
HELP ID- Background Image help returns Help
Topics instead |
|
|
One way video or black screen or no video
over VPN observed |
|
|
7985 XML input - Uppercase & Lowercase
input types allow invalid chars |
|
|
7985 XML Input - Some Input types with
password field flag show password |
|
|
7985 XML Input - Equation type input doesn't
allow symbols |
|
|
7985 should exit from Service app by Exit
key w/ EM login page |
|
|
Could NOT hangup call on shared line after
restart |
|
|
7985 New HW does not suppress upstream
Broadcast, multicast traffic |
|
|
7985 video phone crashes when it receives
cisco gateway fax NSE |
|
|
QED (CSV and Display XML file) Changes for
Phase 2 Ocius 7985 |
|
|
7985 not support softkeyitem as Key-KeyPad |
|
|
Berbee IP phone service returns- unable to
display service error |
|
|
7985 should not clear Status object |
|
|
7985 should not append its Devicename in
HTTP Get messsage |
|
|
Softkeys under the settings menu are
misaligned |
|
|
Phone status log should contain more
information |
|
|
One way video seen on call between 7985s |
|
|
Ringing stops playing when the volume is
adjusted during incoming call |
|
|
Phone is using the callback tone as a ring
tone on next call |
|
|
7985 reboots if Option 150 is a String
Data-Type |
|
|
7985 XML Input - equals character (=) looks
like a solid, heavy dash |
|
|
Audio sources do not work on next call after
a failover with call active |
|
|
Cannot change audio output source when
failover with active call occurs |
|
|
Error message is truncated when invalid
Admin VLAN is entered |
|
|
Localization needs to be turned off on the
phone |
|
|
Softkeys are unavailable after pressing the
Window button |
|
|
Help for Power Save Configuration returns
help for Camera Settings |
|
|
Help within the Power Save Configuration
returns Main Menu Help instead |
|
|
Help of SW Port Configuration returns help
for PC Port Configuration |
|
|
Stock quote IP phone service crashed the
phone |
|
|
Domain name cannot be entered when phone
doesn't have an IP address |
|
|
HELP ID- Power save configuration returns
help for Display On |
|
|
Network Configuation Default softkey should
be renamed to Erase |
|
|
User Preferences Default softkey should be
only available when unlocked |
|
|
The popup window after pressing Default
should be more specific |
|
|
7985 - Power save exits XML Service (and
menus) |
|
|
Configuration parameters domain name and DNS
servers lost after upgrade |
|
|
Phone rebooted when using Hoot & Holler
with 2 phones in Shout mod |
|
4.1-Devpack 28.2 |
|
|
Device Package installation has dialog come
up in silent mode |
|
|
7906/7911 |
|
|
7906/7911Check in
7906/11 f/w load to CCM |
|
|
7935/7936 |
|
|
DTMF tone will not
play for consecutive same digits with 7936 |
|
4.1-Devpack
28.1 |
|
|
Link 'View the User Guide for your phone'
not available for 7961/7941 |
|
4.1-Devpack
28 |
|
|
CCMAdmin should not offer option of 72XX
voice platform as a MGCP GW |
|
|
Make 7906 (turboprop) appear in device defaults
and device pulldown FCS |
|
|
7906/7911-Checkin user guide and update CSV
files for online user guide |
|
4.1-Devpack 27.7 |
|
|
QED (CSV and Display XML
file) Changes for Phase 2 Ocius 7985 |
|
|
CIA-680 Support on 3rd
gen phones |
|
|
Call History Enhancements
for Chumbawamba Phase 1 |
|
|
CCMAdmin should not offer
option of 72XX voice platform as a MGCP GW |
|
4.1-Devpack 27.6 |
|
|
CCMAdmin should not offer
option of 72XX voice platform as a MGCP GW |
|
|
ENU Coltrane3.0 Check In
For English-US Locale |
|
|
7920 |
|
|
Coltrane 3.0 Firmware Check-In |
|
4.1-Devpack 27.5 |
|
|
Digital Access WS-X6608 |
|
|
6608 Incorrect marking
DSCP value to 0 |
|
|
6608 shld not
automatically clr connection when ICMP unreachable is rcvd |
|
4.1-Devpack 27.4 |
|
|
Main client is not usable
when find dialog is up in top of window |
|
4.1-Devpack 27.3 |
|
|
7935/7936 |
|
|
Cannot use # or * as first entry while onhook |
|
|
7936 vulnerable to ICMP
attacks |
|
|
7936 doesn't send HTTP
Get with multi tier DNS names in Directory URL |
|
|
Can't place a call from
phone book when it receives a missed call |
|
|
Phone cannot be resetted
to factorydefault when Admin paswd is not known |
|
|
Remote party hears echo
when 7936 used in glass conference room |
|
|
7936 accepts invalid IP
Address and Subnet mask |
|
|
7936 accepts invalid
Alternative TFTP Address |
|
|
Access Admin Setup
without entering the passcode |
|
|
Conference not working on
7936 in SRST mode |
|
|
Web interface allows to
change password with different characters |
|
|
7936 Web Interface allows
different characters in Phone Book |
|
|
7936 Web interface
dosen't prompt for password when phone is restarted. |
|
|
7936 phone retains the
meetme session even after the call manager fails |
|
|
phone may not give Error
tone when incorrect phone number dialed |
|
|
7936 Editing phone Book
doesn't have the asterisk in the required field |
|
|
If call received while
editing ring tone and publisher fails, 7936 hangs |
|
|
7936 Web interface
accepts alphabets in PING |
|
|
Phone will not accept
incoming call while waiting for Ping response |
|
|
7936 Takes long time to
register when PINGED with CCM failover |
|
|
Info for Http Port
paramater on 7936 web page doesn't show port range. |
|
|
Polycom 7936 doesn't
refresh after saving the Alt TFTP address |
|
|
Polycom 7936 allows to
change the Ringer settings in Ringin state |
|
|
Phone book entry on the
web display is not proper |
|
|
7936 reboots when you
configure Admin VLAN id while in active call |
|
|
7936-Call Transfer number
is not displaying in SRST mode |
|
|
Park Information retained
for a long time. |
|
|
DN not displayed while
placing the call on hold & initiating a new call |
|
|
Call initiations fails
from the phonebook with CFwdAll |
|
|
Phone registers with Alt
TFTP when Alt TFTP Address not specified. |
|
|
Phone hangs when used
Diagnostics with CCM failover |
|
|
Mute turns off in this
scenario in 7936 version 3-3-7-0 |
|
|
Second Call on shared
line cannot be resumed or muted |
|
|
7935 & 7936 Polycom
phones lockup on failover, loss of call preservation |
|
|
Display issue when
Meet-Me number is 10 digit |
|
|
Phone does not accept to
change the passcode with valid characters |
|
|
ncorrect display on one
of the phone in sharedline |
|
|
Incorrect LED status on a
phone in shareline with call waiting enabled |
|
|
7936 Transmit Jitter
Extremely Sporadic - 2 Second Cycle |
|
|
7936 won't fallback to a
TFTP server once registered to an SRST router |
|
|
7936 Phone use odd RTP
port numbers |
|
|
7936 phone with phone
load 3-3-8-0 does not work for FAC |
|
|
7936 Outside dial tone
sounds the same as inside dial tone |
|
|
Call gets disconnected if
we press hold & resume multiple times |
|
|
7936 does not play tone
50 (Zip) when someone joins a conference |
|
|
Phone display is
incorrect when a bogus phone load is entered. |
|
|
Phone dosen't ring when
**8 is executed |
|
|
Phone hangs during
failback and failover with meetme |
|
|
Phone displays
Registering after CCM failover in a active call |
|
|
Dial tone stops when
phone receives a missed call |
|
4.1-Devpack 27.2 |
|
|
ITA Display of Zero and
CAPS O - 7960 Font Display |
|
4.1-Devpack
27.1 |
|
|
7911 Add support for Vieo |
|
|
Placeholder CDETS for
Turboprop Feature Commit |
|
4.1-Devpack 27 |
|
|
Name Change Cisco Unified CallManager 4.2 -
ES/SR Wrapper |
|
|
7985 |
|
|
Domain Name shows
up as? when it is not populated by DHCP |
|
|
Onhook dialing does not light Speaker LED in
SRST mode |
|
|
On help button ? page, Back softkey doesn't
work |
|
|
Requesting better administration tools |
|
|
Video pixelation on calls made between Cisco
VT Advantage and 7985 |
|
|
7985 Improper system message wording |
|
|
There were no tones heard when using onhook
dialing |
|
|
No notification on phone when the remote end
of a call is lost |
|
|
Call focus switches off active call when
shared line is used by others |
|
|
Default router field periodically resets
when phone is configured |
|
|
7895 may report multiple Standby CCMs after
fallback |
|
|
Phone does not ignore lower valued Voice
VLAN when multiple CDPs recvd |
|
|
Phone may stop ringing when switching to a
second incoming call |
|
|
Headset mode sends output to the Speaker in
SRST mode |
|
|
Sometimes cannot answer 2nd call by
switching lines in SRST mode |
|
|
Phone sometimes does not direct audio to the
handset in SRST mode |
|
|
Call Forward icon still displays when
fallback to SRST mode occurs |
|
|
When using EditDial of a number the prompt
should start at the beginning |
|
|
Rarely the MWI light is on even when no
messages are pending |
|
|
Phone does not send periodic CNG packets
during long silence breaks |
|
|
Call Waiting Ring setting will only Flash
the MWI lamp during 2nd call |
|
|
Video may freeze at end of call or in
self-view mode |
|
|
Switch should ignore PC Voice VLAN Access
when there is no voice VLAN |
|
|
802.1p frames dropped on phone with Admin
VLAN and PC voice VLAN disable |
|
|
Phone gets stuck in CallManager Unavailable
state |
|
|
Test script causes a watchdog timer
expiration |
|
|
Packets to PC port are re-mapped with 802.1p
when Voice VLAN is 802.1p |
|
|
EditDial followed by lifting handset will
not dial call |
|
|
Phone may continue to display Self View
rather than idle screen |
|
|
Denial of Service mutant script cause the
phone to reset |
|
|
Sometimes phone cannot end call after a CCM
fallback with call active |
|
|
Web Access Enabled/Disabled need to be added
to CCM and phone |
|
|
Phone sometimes does not connect to correct
backup CCM during fallback |
|
|
Phone does not reset when lower numbered
Native VLAN learned |
|
|
Video mute state get out of sync after the
phone is restarted |
|
|
Phone sometimes shows wrong status
msg/softkeys after CM service restart |
|
|
Cannot browse under Directory, Up/D rocker
stuck at the Missed Calls |
|
|
Phone drops ~50% of IP multicast traffic
from SW to PC port |
|
|
7985 MWI Light misbehavior |
|
|
7985g reboots after select softkey then hit
the X key |
|
|
7985 does not play precedence call waiting
tone |
|
|
7985 phone does not display call pickup
visual alerts |
|
|
7985 crashes when running Codenomicon TCP
protocol verification suite |
|
|
7985 phone reboots when pressing the
'Directories' or '?' buttons |
|
|
CCM4.2 - Cisco 7985 Phone softkeys disappear
during Pickup Audio Alert |
|
4.1-Devpack 26.3 |
|
|
Turboprop
Feature Commit |
|
|
7941/7961-7970/7971 |
|
|
no
value for some items on Device INformation page |
|
|
Phone
should display ... for very long Text or Number |
|
|
SSO
Standby RP T/B atm_ha_decode_vc_update+0x23c for ATM PVC bundle |
|
|
Phone
registered to a CM 3.3 shows only one line while call on hold |
|
|
Received
and missed calls show wrong calling party number |
|
|
Time
stamps on console messages and phone display is not the same |
|
|
Deselected
call in sorted call list appears with other selected calls |
|
|
Turbo
Gabage at the end of Network Statistic screen |
|
|
Cancel
softkey has delayed response when looking up a bogus DNS addr |
|
|
Phone
resets wmore volume of call are placed on sidecar lines |
|
|
wbm
failed to extract signature when display filter was used |
|
|
Turbo
Can not remove Doamin Name on phone |
|
|
Phone
does not remove the default router config |
|
|
Increase
max CPU usage timeout for JVM process |
|
|
SIP
TNP 1.1 image stress run freezes phone UI |
|
|
Phones
unable to Rx or Tx Multicast Services when Publisher fails. |
|
|
Phone
w/200 calls active single line reset w/calling phone reset |
|
|
dhcp.conf
could have invalid my name entry |
|
|
Add
consolle trace to indicatie the call is an encripted call |
|
|
Phone
doesn't register when it is unable to resolve the CCM name |
|
|
paging
group display delayed on 7911 with CME |
|
|
get
SW port returned -1 error after downgrade to 6.0(2)SR1 |
|
|
Phone
stops playing multicast after an unanswered call |
|
|
local
Ip/port value is cleared but others are kept for an ended cal |
|
|
LED
does not blinking red while the DCP is busy |
|
|
7970/7971
Touch Screen issue IP Phone URL shows Delay |
|
|
logins
with sys group permissions on release signed phones |
|
|
Skittles
timeZone tag errors |
|
|
Turbo
Background Image thumbnails not displayed in correct order |
|
|
7961
Row of Pixels missing on Line View graphic |
|
|
Skittles
phone locks up when SEP dateTimeSetting is empty |
|
|
Skittles
phone locks up when SEP dateTemplate is MM/DD/YY |
|
|
Phone
display goes blank for consult transfer to busy monitor line |
|
|
when
PickUp softkey is pressed on onhook phone displays ??? |
|
|
Sittles
Service URI cause phone to crash |
|
|
need
to press mute twice for an incoming intercom call |
|
|
Assign
a same IP port to RX and TX socket - casues 1 way audio |
|
|
Phone
doesn't play Zip/ZipZip Tones toward network |
|
|
Phone
Rcvr Lost Pkt reports as a negative no under impairement |
|
|
SIP
TNP DSP debug seen when pressing Settings, Directories, or Services |
|
|
Reference
getPegs() via IMedia interface instead of directly |
|
|
Turbo
Phone receives mcast pkts when port open forMcast transmit |
|
|
Turbo
Error Verifying Config Info after LSC install on secure phone |
|
|
README-SGM-pdsources
on DVD has SGM references |
|
|
Phone
Should handle gethostbyname failure and print appropriate Err Msgs |
|
|
Phone
not displaying all Placed call list when pressing up/down button |
|
|
Corporate
directory search fails if username contains special characters |
|
|
wirelss
client to client can not pass traffic |
|
|
Service
URL feature assigned in em profile does not work |
|
|
Phone
sends Duplicate DHCP Discover Message |
|
|
Phone
freeze after reset stress |
|
|
Phone
displays wrong msg when registration rejected for security reason |
|
|
phone
doesn't show up old admin vlan id in Current Admin. VLAN Id |
|
|
Corporate
Directory Search Fails When using Russian Locale |
|
|
Add
Title to Line View to identify which line the calls belong to |
|
|
Having
directory menu open causes Callback to not working properly |
|
|
Exit
soft key is not working in Callback Screen |
|
|
HTTP
CGI ModeInfo query does not return if Services URL doesn't resolve |
|
|
Ethernet
Disconnected Mesasge does not appear when Ethernet unplugged |
|
|
Turbo
Missing status messages on Load Server parameter |
|
|
No
status message when TFTP service is down on load server |
|
|
LineInfo
web age query does n't show up Messagewaiting Indication. |
|
|
Phone
won't failback to a TFTP server once registered to an SRST router |
|
|
HTTP
req canclled msg when hitting a softkey |
|
|
Japanese
locale (td-sip.jar) not loading on SIP phones. |
|
|
Removing
JVM from 7.0 on 8.0 CPK files (to avoid out of space errors) |
|
|
Turbo
status message No Default Router after changing DHCP=no to yes |
|
|
Phone
does not preserve the state of mute/spkr button in handset mode |
|
|
Skittles
phone does not complain with junk value in displayOnDuration |
|
|
Making
DSP standalone on phones- dsp.cnu reads dspfw.bin |
|
|
select
image Userpreference->Background image display invalid png icon |
|
|
CDP
crashs from broadcasted CDP pkt, results in restart of all apps |
|
|
Privacy
lamp is not being displayed correctly on 7941 SCCP phone |
|
|
add
fault-tolerance to filesystem |
|
|
Phone
unable to come out of Service Menu using CANCEL softkey |
|
|
Phone
responds to CDP triggers from upstream port |
|
|
phone
does not play precedence CW tone |
|
|
Calls
drop during CME failback |
|
|
Phone
is stuck if Encrypted Config is on and supporting load is absent |
|
|
phone
doesn't come up with DHCP enable when Voice VLAN = Access VLAN |
|
|
Incorrect
response for unicast/invalid IP adress for RTPMTx i p URI |
|
|
CiscoIPPhoneExecute
ExecuteItem priority 1 is ignored in some cases. |
|
|
Invalid
Ip Address to be displayed while validating Null values. |
|
|
Turbo
lost audio w/ 100% broadcast traffic |
|
|
Status
Msg timestamps changed between 24hr/12hr formats on reset |
|
|
CP-7970
firmware version 7.0(1) distorts background image color |
|
|
Softkey
changes from Connected Transfer state to On Hold state |
|
|
Phone
is loosing the querystring parameter on the refresh |
|
|
Phone
Multicast services not working |
|
|
LSC
Installed Status Messages is not displayed on phones |
|
|
cBarge
Target phone changes focus when other party cBarges |
|
|
Phone
doesn't dial from placed call listwhen editdial& dial is pressed . |
|
|
Phone
Displays UI with no keys for a shared line scenario. |
|
|
Phone
CGI URLs never complete HTTP transaction |
|
|
Services
page text does not display properly |
|
|
Idle
phones never send SCCP TimeDateReq to sync clock |
|
|
Pressing
the '.' soft key in the edit menu doesn't force Kate String T/O |
|
|
Clicking
noise is heard in encripted call when duplicating packets |
|
|
Phone
plays garbled audio for PA prompts |
|
|
phone
displays ??? as Codec in Call Statistics window |
|
|
Call
Stats window displays wrong info for Rcvr Lost Pkts/Discarded |
|
|
IP
Phones use random UDP source port for RTP media |
|
|
Phones
stop sending KA when backup TCP link down |
|
|
call
bubble does not disappear when there is no active call |
|
|
High
End Phones connect to CCM sub that is not present in the CTL file |
|
|
Turbo
fine-tune displaying errors of dspSendFrame _framePutEgressFrame |
|
|
Turbo
InsideDialTone could not be stopped after removing CFwdAll |
|
|
UDI
Support |
|
|
Turbo
Codenomicon HTTP test 39730 causes sunvm CPUTime Limit Exceeded |
|
|
Add
core file decoded core file to the serviceability webpage |
|
|
SIP
phone loads and CCM are out of sync for PC Voice VLAN Access |
|
|
GARP
enable/disable reversed |
|
|
Property
Errors - Settings Can Be Lost |
|
|
phonerebooting
when secondary CME inaccessible and keepalive is 10 |
|
|
Enhance
the flush operation in the RecordStore |
|
|
HTTP
Client locks up upon consecutive posts to CGI Execute |
|
|
No
prompt/status in Detail call history record |
|
|
Dial
Softkey Enabled when no Active Audio Path or no CCM |
|
|
Erase
from Top-Level Settings Menu does delete sidecar contrast |
|
|
SIP
Phone does not do a TLS session reuse after network failure |
|
|
RMS
Store must be deleted in order for phone to boot correclty. |
|
|
Phone
stuck after erase under Settings menu |
|
|
JPhone
Overview displays incorrect topcall if some RIUs made private |
|
|
GARP
enabled native code returning incorrect value |
|
|
Phone
could not recover after DNS entry be corrected |
|
|
Phone
sends Invalid Message for SCCP v3 and v4 |
|
|
Phone
Answer softkey not displayed for new icoming call |
|
|
Remote
In Use Icon/LED not shown when shared line is private |
|
|
HTTP
Authentication Does not Show Response |
|
|
Able
to Change Ring Volume Even when Setting Access set to Disable |
|
|
TimeDateReq
to sync clock causes KeepAlive to miss one interval. |
|
|
7970/7971
InCorrect Date Format Shown Under Missed Calls |
|
|
2
meg file limit cause double boot when upgrading to 8.0 load |
|
|
JAVA/TNP
Log/trace related changes |
|
|
CNU syslog changes for 7.0.2.x branch |
|
|
getportcfg
check for errors on msgsnd() |
|
|
Display
distorts, when held calls goes from three to two |
|
4.1-Devpack 26.2 |
|
|
CMM
Echo Cancel Coverage 8 and 16 ms should be removed |
|
4.1-Devpack 26.1 |
|
|
ATA18X |
|
|
ATA
SCCP Incorrect Call Waiting behavior |
|
|
Conference
to ATA-Phone thru H323 & ATA-phone on same CME doesnt work |
|
|
ATA
flooding callmanager with Softkeyevent New call skinny messages |
|
|
Problem
transfering calls using ATA and CME |
|
|
Update
signaling ToS to be consistent with current design guides |
|
|
ATA186
configuration web page should state clicking rather than click |
|
|
ATA
SCCP sent AVT message when sent DTMF to SCCP endpoint |
|
|
No
Secondary dialtone played by ATA SCCP |
|
|
ATA186
excessive TCP ACK delay after receiving SKINNY message |
|
|
ATA
SCCP sends excessive StationSendTimeDateReqCSCef39491 |
|
|
7940/7960 |
|
|
Phone
without DHCP cant recover Dup IP address |
|
|
7960/7940
characters by pressing '0' with li-ffr.4-1-3-JPN are funny. |
|
|
help
symbol missing in text press - key to cancel for english locale |
|
|
7960
Settings -> RingType menu changes doesn't take effect |
|
|
7910
DSCP values need to be consistent with current design guides |
|
|
EM
logout restarts the IP Phone. |
|
|
Small
MTU causes CVTA to H323 video call failure |
|
|
7960/7914
Ringer type off by 4 lines. |
|
|
Update
dictionary file with SeaDragon new phrases |
|
|
Phone
Continuously displays Requesting RingList File ...... |
|
|
Phone
UI Lines separating the DN disappear as it failover to subscriber |
|
|
Posting
Line34 URI enables Line30 on ip phone. |
|
|
http
///CGI/CallInfo does n't display all lines call Info. |
|
|
ActiveSoftkeys
eg redial, New Call are shown when pubisher CCM is down. |
|
|
In
CallInfo the CalledPartyName field is not proper for Conf call |
|
|
In
http request for CallInfo/LineInfo the Prompt field is showing null |
|
|
Line
button does not answer call with 2 calls on hold already on line |
|
|
DHCPReleaseMessage
should be unicast to DHCPserver,not on broadcast IP. |
|
|
7960
Phone doesn't display blank URL sign or URL without label on line |
|
|
Volume
control keys when calling a busy no affects ringer(ver 8.0(0.16)) |
|
|
7960
Phone reset from settings with **#** while on call hold |
|
|
7960
Phone loose RTP stream when restart from CM |
|
|
7960
Pressing Line button twice ends calls on Phone in ringing state |
|
|
BigApp
does not kick back to LA on version mismatch in XMLDefault.cnf.xm |
|
|
phone
7940/7960 should escape '#' symbol |
|
|
7960
doesn't receive MOH or DHCP when Voice VLAN = Access VLAN |
|
|
RED
LAMP indication on 7914 for In Use Remotely does not work - 7.2(3) |
|
|
7960
MWI functionality should be consistent with current phone behavior |
|
|
7960
Phone volume not being set properly at RTPRx start |
|
|
Menu
object as IDL URL, menu item 1 selected when phone goes off-hook |
|
|
MWI
lamp glows continuosly after a CB notification for the first set CB |
|
|
IP
phones become unregistered from both SRST and CM |
|
|
Phone
load Upgrade to 7.2(3) causes RXshort errors on PC port |
|
|
Phone
drops untagged PC Traffic |
|
|
Handle
Current Call missing when dialing from Directory |
|
|
Secure
Phones does n't cancel tftp request while cancel key is pressed |
|
|
7940/60
PC port 100M does not receive network traffic intermittently |
|
|
Unable
to dial the CB notified number during ringing state |
|
4.1-Devpack 26 |
|
|
6608 E1/T1 |
|
|
Calls
through 6608 T1 CAS trunks are not preserved |
|
|
T1-CAS
E&M ports on a 6608 card unregistering during stress test |
|
|
Periodic
T1-CAS E&M channel out-of-service during 6608 stress test |
|
4.1-Devpack 25.4 |
|
|
CM
need support for new phones in devicelistx.asp file |
|
4.1-Devpack 25.3 |
|
|
ES/SR Installation needs corresponding code for CSCsb44801
resolution |
|
|
Enlarge splashscreen in ES/SR
installaton |
|
|
Need new sections for file copy ops |
|
|
Update SQL script handling |
|
|
Enhance error handling reporting and dialogs |
|
|
End of installation Dialog Changes needed for Device
Package |
|
|
7911 |
|
|
Checkin 7911 f/w loads to create Device Packs for FCS |
|
4.1-Devpack 25.2 |
|
|
Implement group listening. |
|
4.1-Devpack 25.1 |
|
|
7902/7905/7912 |
|
|
7912 fails due to malicious VLAN tagging |
|
|
7912 does not play UK dial tone |
|
|
7905/12 phones lose Service button after EM update |
|
|
phone - 7912 phone reboots after receiving 3 IMs quickly |
|
|
Only a 7912 shared number phone work when configured
max-dn dual-line |
|
|
No dial tone after the 7905 and 7912 SCCP failover to SRST |
|
|
7912G-A phones cause PC's behind them not to retain an IP
Address |
|
|
Long delay for PC to obtain network connectivity when used
with 7912G-A |
|
|
7912/05 should always Reset unless an rtp stream is active |
|
|
CCCM 5.0 & 7905/12 does not show external number on
top line of display |
|
|
7912 SCCP sends excessive StationSendTimeDateReq in idle
mode |
|
|
7912/05 excessive TCP ACK delay after receiving SKINNY
message |
|
|
7912/05 RTPMTx sets TTL of sent multicast packets to 1 |
|
|
Timedate req. msg. storm from at midnight |
|
4.1-Devpack 25 |
|
|
PCM change breaks 4.2 and lower builds. |
|
|
7935 |
|
|
CP-7935 generates choppy audio when in a conference call |
|
|
7920 |
|
|
Extension Mobility does not work with Services URL Button
on 7920 |
|
|
7920 Doesn't Support Vibrate URI |
|
|
Need a menu to display configured regulatory domain |
|
|
Need a menu to display current transmit power |
|
|
7920 Does Not Support CCA Versions of QBSS |
|
|
7920 can spontaneously re-register to CM in idle with
INF-MIB error |
|
|
7920 Can Associate to a Lower Priority Profile When Set to
Auto Profile |
|
|
Upgrade to 2.0 will cause phone lock password corruption |
|
|
CCM 5.0 Centralized TFTP compatibility enhancement |
|
|
Port 17185/udp is open on 7920 phone |
|
|
7920 RTPMTx sets TTL of sent multicast packets to 1 |
|
|
7920 call-forward noan on second active call results in
phone hanging |
|
|
7920 can corrupt the CCKM Timestamp |
|
|
Invalid XML object sizes can cause the 7920 to reboot |
|
|
Idle URL can cause the 7920 to lock up |
|
|
7920 will roam off a strong signal AP to a weaker one |
|
|
7920 should continue streaming RTP packets when on Mute |
|
|
7920 can fail to ACK G711 packets during a call |
|
|
7920 Can Roam More Frequently With 12.3(7)JA AP Image |
|
|
7920 Can Stop Scanning Although Still Associated |
|
|
7920 send 802.11 Auth suddenly and it causes choppy audio |
|
|
Channels in Active List are not flushed after 3 missed CM
Keepalives |
|
|
Emergin's alert tone volume needs to be limited when
on-call |
|
|
CP-7920 is not responding to AP packets |
|
|
MWI tone can be very loud to user if CP-7290 re registers |
|
|
Need to roam when QBSS max threshold is met |
|
|
7920 MR2.0.1 firmware upgrade |
|
4.1-Devpack 24.9 |
|
|
7936 |
|
|
7936 Transmit Jitter Extremely Sporadic - 2 Second Cycle |
|
4.1-Devpack 24.8 |
|
|
Need tag for 6608-MTP/CFB in ccm xml |
|
4.1-Devpack 24.7 |
|
|
VG224 configured for shared line on Callmanager fails |
|
|
help symbol missing in text press - key to cancel for
english locale |
|
4.1-Devpack 24.6 |
|
|
Update/Make 7911 ready for FCS and prepare Skate SR build |
|
4.1-Devpack 24.5 |
|
|
7.0(2)SR1 image for the 7941/7961 checkin to 3.3, 4.0 and
4.1CCM release |
|
|
7970/71 7.0(2)SR1 image check in |
|
|
Add online doc. name to 7911 SCCP loads |
|
|
Stndrd Feature 7960 sftky profile fail on 7940 CallBack
equipped phone |
|
|
Update/Make 7911 ready for FCS and prepare Skate SR build |
|
|
7941/61 |
|
|
Phone freeze after reset stress |
|
|
Exit soft key is not working in Callback Screen |
|
|
CDP crashs from broadcasted CDP pkt, results in restart of
all apps |
|
|
Privacy lamp is not being displayed correctly on 7941 SCCP
phone |
|
|
add fault-tolerance to filesystem |
|
|
Phone responds to CDP triggers from upstream port |
|
|
phone doesn't come up with DHCP enable when Voice VLAN =
Access VLAN |
|
|
7970/71 |
|
|
Unknown resolved
defects |
|
|
4.1-Devpack 24.4 |
|
|
Application menu items should not be in all CAPS |
|
|
CM need support for new phones in devicelistx.asp file |
|
4.1-Devpack 24.3 |
|
|
6624 |
|
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
4.1-Devpack 24.2 |
|
|
remove loggingDisplay option for 7941...7961G-GE phones
from CCM/Windows |
|
4.1-Devpack 24.1 |
|
|
VG224 configured for shared line on Callmanager fails |
|
4.1-Devpack 24 |
|
|
7941/61 |
|
|
checkin 7.0(2) firmware for 7941/7961 phones into
CCM/Windows |
|
|
7970/71 |
|
|
7.0(2) firmware for 7970/71 |
|
4.1-Devpack 23.2 |
|
|
6608 T1/E1 |
|
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
|
CallManager may incorrectly put a 6608 CAS port OOS |
|
|
6608 Glare conditions on T1 CAS is not cleared
appropriately |
|
4.1-Devpack 23 |
|
|
7940/7960 |
|
|
Greyed ERASE softkey is actually enabled |
|
|
Caller ID gone from shared line after a barge |
|
|
>in 7940/60 i-button help text |
|
|
sidecar lamp shows red for barge/cbarged calls |
|
|
7960/40 Device Info page does not follow Message Waiting
Lamp Policy |
|
|
Display settings on Phone should be changed for Restricted
Display |
|
|
7960 can load a Ringlist.xml with more than 50 entries |
|
|
Remove conditional code |
|
|
IPPS authentication credentials, % sign not URL encoded |
|
|
PC can't ping 7960 phone with dot1p configured |
|
|
Next key not displayed for CiscoIPPhoneDirectory that
appears in Service |
|
|
ARP cache timeout if set 0 in 7960 phone flood the n/w
with ARP queries |
|
|
7960/7940 characters by pressing '0' with li-ffr.4-1-3-JPN
are funny. |
|
|
Build P0030701T018 ES Load |
|
|
30th digit of Speed dial display text is not properly
displayed |
|
|
7940/60 plays multicast from other VLANs as well as the
voice VLAN |
|
|
phone reboots after several hours of operation over high
delay network |
|
|
CDP code does not verify destination MAC address |
|
|
7940/60 Little App accepts DHCP Offer from a different
VLAN |
|
|
No Display for dialed number thru personal fast
dial/directory lookup |
|
|
Loader Ping fails if DNS not available |
|
|
7960 Settings -> RingType menu becomes unresponsive |
|
|
Unwanted Debugs appear on Console |
|
|
* and # are causing settings softkey to be updated in
settings submenus |
|
|
7960 Line text Label contains garbage when sent to SRST
router |
|
|
Inconsistency in Streaming Stats between web page and
phone when MoH |
|
|
Second 7914 expansion module displays garbled characters |
|
|
7960 phone drop G.729b frames when silence suppression is
on |
|
|
7960 - DHCP broadcast for renewal instead of unicast at
50% lease time |
|
|
Setting menu Softkeys intermittently are not responding |
|
|
7940/60 sends AdminVVLAN in response to CDP Trigger with
VVLAN query |
|
|
Phone sends extra off-hook message |
|
|
PC connected to 7940/60 has slow network communication |
|
4.1-Devpack 22.6 |
|
|
PC logging option is not available for makaha |
|
|
Analog Access
WS-X6624, |
|
|
Digital Access
WS-X6608 |
|
|
GW config page for cat6kT1 VOIP shows fields required when
optionl |
|
|
Change configuration fails to open the GWconfigpage over
securechann |
|
|
Clicking help in gatewaypage prevent users from viewing
device info |
|
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
|
CCM4.1.2 web page for Gateway device config should be
https |
|
|
6608 T1 CAS channels are stuck in CSCallClearing state |
|
|
Inactive channels are not busied out when 6608 loses CCM
registration |
|
|
6624 FXS ports stuck in offstate state / ReleaseInd Q931
state |
|
|
7935 |
|
|
7935 susceptible to ping attack, causing odd/delayed
behavior |
|
|
Using keys during call causes chopiness |
|
|
7935 loses connectivity on voice RTP broadcast packets
reception |
|
|
CP7935/CP7936 Does Not Support DTMF Out of Band |
|
|
7935s did not come back up after upgrade from Parche to
Skate |
|
|
After a CCM upgrade phone displays rebooting..... |
|
|
7935/7936 Phone does not support broadcast suppression |
|
|
Slow audible feeback for key presses |
|
|
TFTP Client Behavior - 2 TFTP Servers |
|
|
7936 freezes after on-hook dialing |
|
|
6608 Lost packet counter is increased by 16 for every
press of DTMF tone |
|
|
Phone requires power-cycle if publisher fails while Call
Waiting in prog |
|
|
Mute doesn't work on 7936 (Call waiting enabled) when
publisher fails |
|
4.1-Devpack 22.5 |
|
|
7936 |
|
|
Using keys during call causes chopiness |
|
|
CP7935/CP7936 Does Not Support DTMF Out of Band |
|
|
7935/7936 Phone does not support broadcast suppression |
|
|
Slow audible feeback for key presses |
|
|
TFTP Client Behavior - 2 TFTP Servers |
|
|
7936 freezes after on-hook dialing |
|
4.1-Devpack 22.4 |
|
|
Add 7985 QED support CCM versions 4.X and 5.X |
|
|
7911 QED changes to support alt scripts and load server |
|
|
Checkin ip7961.pdf ver3 into3.3.5.eng.spec,
4.0.2.eng.spec, 4.1.2.eng... |
|
4.1-Devpack 22.3 |
|
|
Enable visibility of Makaha types in dev packs
3.3.5.eng.spec, 4.0.2. .. |
|
4.1-Devpack 22.2 |
|
|
Enable visibility of Makaha types in dev packs
3.3.5.eng.spec, 4.0.2. .. |
|
4.1-Devpack 22.1 |
|
|
GW config page for cat6kT1 VOIP shows fields required when
optionl |
|
|
Change configuration fails to open the GWconfigpage over
securechann |
|
|
Clicking help in gatewaypage prevent users from viewing
device info |
|
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
|
CCM4.1.2 web page for Gateway device config should be
https |
|
4.1-Devpack 22 |
|
|
1700 GWs FXO ports are allowed to be configured for diff
signaling. |
|
|
MLPP config not available for 3845 MGCP gateway |
|
|
Enable visibility of Makaha types in dev packs
3.3.5.eng.spec, 4.0.2. .. |
|
4.1-Devpack 21.5 |
|
|
7985 |
|
|
Add 7985 QED support CCM versions 4.X and 5.X |
|
4.1-Devpack 21.4 |
|
|
Mandatory parameter URL help has to be present by default |
|
|
7961/7941 font should be more readable - suggest making
taller |
|
|
7910 |
|
|
7910 fowarded call display syntax error |
|
|
SD1C Phone firmware parses phone config file incorrectly |
|
|
Phones To Be More Ambitious Towards Updating Firmware |
|
|
Echo fades in and out when talking IP phone to IP phone |
|
|
Ip Phone doesnt accept option 66 with trailing dot in
hostname |
|
|
Slow performace when data AND voice vlan is tagged
(802.1q) |
|
|
Callwaiting does not work on 7910 ip phone |
|
|
Disabling settings w/o disabling ring volume |
|
|
Dial keys do not respond for 10 secs after pressing **# |
|
|
7940/7960 SIP phones not handle out of order/mis-sequence
packets |
|
|
Phone fails to come up when wrong load Id is mentioned on
phone page |
|
|
7960 send StationAlarm w/ incorrect text if no RegAck |
|
|
Faint audio is heard in the speaker while using handset |
|
|
Set Ringer Duration ignored by Seaview phone registd with
ParcheCCM |
|
|
7910 should not drop the 1st call by pressing line on 2nd
call |
|
|
An error at a certain key sequence |
|
|
7910 conf phone does not displays called/calling name |
|
|
Key rollover broken/missing digits when dialling |
|
|
C3PO Frame Buffer overflow causes COS3 packet drop |
|
|
Audio cut through delay during Call Waiting Answer |
|
|
7960/7940 Voice Quality Degradation With Echo Back To
Remote Party |
|
|
TFTP 2 address edit display contains garbage |
|
|
7910 ip displays connected call information wrongly |
|
|
7910 phone having DN of 24 digits reboots if CFA number
crosses 9 digit |
|
|
7910 phone does n't displays fwd for forwarded
intercluster call |
|
|
7940/60 handset/headset SRL/RLR mid-spec adjustment |
|
4.1-Devpack 21.3 |
|
|
1700 GWs FXO ports are allowed to be configured for diff
signaling. |
|
|
ONLINE HELP Ring tone help screen needs to replace Alert
with Ring |
|
|
ONLINE HELP Device Configuration help need updated with
new submenus |
|
|
ONLINE HELP Help info for editing IP address needs
addtional steps |
|
|
ONLINE HELP Erase softkey help under Settings needs more
information |
|
|
ONLINE HELP Help for Network Settings DNS Server 1 returns
error |
|
|
ONLINE HELP Default softkey under some User Preferences
returns no help |
|
|
No Help content for the softkey OPickUp. |
|
4.1-Devpack 21.2 |
|
|
1700 GWs FXO ports are allowed to be configured for diff
signaling. |
|
4.1-Devpack 21.1 |
|
|
Video capability for Communicator has to be added |
|
|
Maketypes needs run after Product CSV's added to branch |
|
|
support for EM2-HDA-4FXO in CCM |
|
4.1-Devpack 21 |
|
|
7.0 firmware and associate files checked into CallManager |
|
4.1-Devpack 20 |
|
|
7920 |
|
|
IP phone services do not work |
|
|
Need Capability to Disable Configurable Menus |
|
|
7920 Should Be Less Aggressive for LEAP |
|
|
Softkey Templates Do Not Work with 7920 |
|
|
Duration fields are occasionally wrong in 802.11Data null
packet |
|
|
7920 does not support virtual carrier sensing |
|
|
7920 Red button cannot end call when far end busy |
|
|
7920 placed call log may not include discarded digits |
|
|
No Connectivity After Downgrade to 1.08 When Using Static
WEP |
|
|
Ringtones are displayed incorrectly when less than 4 rings
available |
|
|
7920 can change focus to another line when on call |
|
|
7920 user guide cannot be loaded from CCMUser pages |
|
|
Intermittent AP retransmissions if 7920 is unavailable |
|
|
7920 Sometimes Roams Unexpectedly Due to Packet Loss |
|
|
7920 can get stuck in a scanning state |
|
|
7920 does not look at source port for Multicast |
|
4.1-Devpack 19 |
|
|
Turbo-Some line settings not available |
|
|
6608 MTP/CFB |
|
|
Tertiary CM not listed in Transcoder Device Configuration
Page |
|
|
6608 cfb unregisters after one missed keepalive |
|
|
conference bridge not getting registered to correct ccm |
|
|
ICMP Hard error handling
for 6608 MTP/CFB |
|
4.1-Devpack 18.4 |
|
|
7.0 firmware and associate files checked into CallManager |
|
4.1-Devpack 18.3 |
|
|
7912 |
|
|
7905/12 display English prompt at Services page |
|
|
Issues with processing of DNS packets |
|
|
Settings Access restricted option behaves like enabled on
7912 |
|
|
7912 can not initiate hold w/ multiple calls per line and
shared lines. |
|
|
The browser window on the 7912 opens when it should not |
|
|
There is no dial tone when exiting from the directory menu |
|
|
7912 Chinese Locale Unable to display calling number |
|
|
CHS-Wrong Phone display |
|
|
DTMF when users mash 7912 keys unrecognizable to AA/IVR |
|
|
7905/7912-Does Not Format '?' Characters in Services URL
Properly |
|
|
XML Error [4]-Parse Error on 7912G when creating FastDial
in PAB |
|
|
Found dtmf digits fail when calling into Meeting Place
IVR. |
|
4.1-Devpack 18.2 |
|
|
7961 Phone Icon missing in the Call Manager Find/List
Phones |
|
4.1-Devpack 18.1 |
|
|
7902/05/12 |
|
|
7905/12 display English prompt at Services page |
|
|
Issues with processing of DNS packets |
|
|
Settings Access restricted option behaves like enabled on
7912 |
|
|
7912 can not initiate hold w/ multiple calls per line and
shared lines. |
|
|
The browser window on the 7912 opens when it should not |
|
|
There is no dial tone when exiting from the directory menu |
|
|
7912 Chinese Locale- Unable to display calling number |
|
|
CHS- Wrong Phone display |
|
|
DTMF when users mash 7912 keys unrecognizable to AA/IVR |
|
|
7905/7912- Does Not Format '?' Characters in Services URL
Properly |
|
|
XML Error [4]-Parse Error on 7912G when creating FastDial
in PAB |
|
|
Found dtmf digits fail when calling into Meeting Place
IVR. |
|
|
ATA18X |
|
|
ATA has poor voice quality when NumTXFrames set with high
value |
|
|
ATA (SCCP) does not process Calling Party Name in second
CallInfo |
|
|
Issues with processing of DNS packets |
|
|
Unable to set UI password for ATA188 |
|
4.1-Devpack 18 |
|
|
7902/05/12 |
|
|
TFTP Client Busy Retry Behavior |
|
|
7912 doesnt display correct Softkeys when using MCDN
feature |
|
|
IP Phone 7905 not responding to http commands |
|
|
7912 cant ring immediately when receiving a call after
fallback |
|
|
MWI will be turned off by incoming call |
|
|
7905/12 display English prompt at Services page |
|
|
7912 ignores StationClearPriNotifyMessage from CME |
|
|
Authentication delay between IP Phone 7905 and CM 5.0 is
to long |
|
|
Issues with processing of DNS packets |
|
|
Settings Access restricted option behaves like enabled on
7912 |
|
|
7912 can not initiate hold w/ multiple calls per line and
shared lines. |
|
|
7912-RTP URI push during call requires user to cycle hook
twice to end |
|
|
7912 dies when configuring Graphics via TFTP on CCM 4.1 |
|
|
The browser window on the 7912 opens when it should not |
|
|
During cross upgrade, power off/on the phone & the
phone never come up |
|
|
There is no dial tone when exiting from the directory menu |
|
|
7912 Chinese Locale- Unable to display calling number |
|
|
CHSWrong Phone display |
|
|
Found dtmf digits fail when calling into Meeting Place
IVR. |
|
|
DTMF when users mash 7912 keys unrecognizable to AA/IVR |
|
|
7905/7912- Does Not Format '?' Characters in Services URL
Properly |
|
|
XML Error [4]-Parse Error on 7912G when creating FastDial
in PAB |
|
|
Found dtmf digits fail when calling into Meeting Place
IVR. |
|
4.1-Devpack 17.5 |
|
|
support for EM2-HDA-4FXO in CCM |
|
|
Support for BRI vics on 26/36/37/38xx |
|
|
Support for BRI vics on 26/36/37/38xx |
|
4.1-Devpack 17.4 |
|
|
CSV and XML files for Baker Project should be updated to
reflect new fea |
|
4.1-Devpack 17.3 |
|
|
CSV and XML files for Baker Project should be updated to
reflect new fea |
|
4.1-Devpack 17.2 |
|
|
support for EM2-HDA-4FXO in CCM |
|
|
Video capability for Communicator has to be added |
|
|
ONLINE HELP- Ring tone help screen needs to replace Alert
with Ring |
|
|
ONLINE HELP- Device Configuration help need updated with
new submenus |
|
|
ONLINE HELP- Help info for editing IP address needs
addtional steps |
|
|
ONLINE HELP- Erase softkey help under Settings needs more
information |
|
|
ONLINE HELP- Help for Network Settings DNS Server 1
returns error |
|
|
No Help content for the softkey OPickUp. |
|
|
ONLINE HELP- Default softkey under some User Preferences
returns no help |
|
|
No Help content for the softkey OPickUp. |
|
4.1-Devpack 17 |
|
On 7970 Display-on-Time shows default value after setting it to
blank |
|
7940/60 (Load - P00307020200): |
|
802.1x auth state remains after PC disconnect |
|
|
Video stream not terminated when CM is down Bsphere 2628 |
|
|
Incorrect status msg when no ctl on phone and modified ctl
dwnld |
|
|
NetworkConfigurationX tag names do not match Network
Config UI |
|
|
7960/40 does not support QueryStringParam as documented in
SDK |
|
|
Help for side car buttons throw an error |
|
|
IPSvcssupported xml fields size are 1 less than max |
|
|
IPsvcNew http headers support as per SDK 4.0(1) |
|
|
Lock icon overlaps to page title text |
|
|
Mid-call video starts when active call is in mute state |
|
|
Idle URLRefresh page does not recover after a packet loss |
|
|
Phone shows encrypted call with CM 3.3 |
|
|
Phone accepts invalid/Reserved/Multicast IP address |
|
|
Security Configuration menu name should be separate from
title |
|
|
invalid display by ip phone on key pad uris push |
|
|
Clear softkey doesnt clear interface stats on HTTP page |
|
|
phone not updating volume changes during call preservation
state |
|
|
Autodial fails on choosing hold option for the current
call |
|
|
Handle current call not displayed on dialing from
directories |
|
|
Not able to scroll down to see help pages displayed by i
button |
|
|
pressing first line speed dial causes second line to go
offhook. |
|
|
7940/60 phone should use HTTP 1.1 for URL with IP address |
|
|
Auto line select enabled prevent use of softkeys on 1st
line |
|
|
No PORT_UP event on 7940 if PCport on Phone changed frm
10Mbps-100Mb |
|
|
7960 stuck in booting process when press service before
phone alive |
|
|
phone sends tftp request to ip address 0.0.0.0 |
|
|
7960/7940Voice Quality Degradation With Echo Back To
Remote Party |
|
|
Phone does not retains Volume Settings changes |
|
|
Shared line call doesnt display toggling between lines
correctly |
|
|
7960/40 phone will not fail back to primary |
|
|
Support calloc caller PC broke LA built. |
|
|
Change in behavior of resuming the call that is onhold on
IP Phone,7.1.2 |
|
|
Phone connects to secure SRST if bad config |
|
|
Clouseau debug infrastructure
implementation in 7960 sccp phones. |
|
|
Retain old BA while LA upgrade |
|
|
speaker button won't work with sidecar |
|
|
Disable the display debug tracing by default on 7960
phones |
|
|
Update copyright year on mid-range IP Phone boot display |
|
|
7940/7960 display HTTP error[11] when pressing
Services/Directory button |
|
|
After a preserved calls is terminated, the phone is stuck |
|
|
Key rollover with Hold and EndCall Softkeys causes wrong
action |
|
|
7940/60 stuck in Configuring CM List state |
|
4.1-Devpack 16.1 |
|
TurboError Extracting File using latest
tc-sccp.jar file |
|
4.1-Devpack 16 |
|
Known Caveat for 7940/60 phones |
Change in behavior of resuming the call
that is onhold on IP Phone,7.1.2 |
|
Neanderthal - Implement JAVA side and
QED CM interface |
|
|
7970/7971 |
|
|
7970 won't boot w/ inline power |
|
|
7905/7912 |
|
|
TFTP Client Busy Retry Behavior |
|
|
7912 doesnt display correct Softkeys
when using MCDN feature |
|
|
IP Phone 7905 not responding to http
commands |
|
|
7912 cant ring immediately when
receiving a call after fallback |
|
|
MWI will be turned off by incoming call |
|
|
7905/12 display English prompt at
Services page |
|
|
7912 ignores StationClearPriNotifyMessage
from CME |
|
|
Authentication delay between IP Phone
7905 and CM 5.0 is to long |
|
|
Issues with processing of DNS packets |
|
|
7912 RTP URI push during call requires
user to cycle hook twice to end |
|
|
7912 dies when configuring Graphics via
TFTP on CCM 4.1 |
|
|
During cross upgrade, power off/on the
phone & the phone never come up |
|
|
Found dtmf digits fail when calling into
Meeting Place IVR. |
|
|
6608 |
|
|
Burst of static during ringback and
connect on calls through 6608 |
|
4.1-Devpack 15 |
|
7920 |
|
|
BSSID is all Zeros in Reassociation
Packets |
|
|
Site Survey Detail Shows the Same Info
for All APs Sometimes |
|
|
7920 Does Not Answer IGMP Query |
|
|
7920 Could Get Into Continuous Roaming |
|
|
7920 May Get 1 Way Audio Without
ARP-Caching |
|
|
7920 Will Sometimes Show RSSI = 1 |
|
|
Packets are Sent at 1mbps rate Off Call
When 7920 Uses a Non-Auto Rate |
|
|
7920 Advertises All Rates Are Supported
When Non-Auto Rate Is Configured |
|
|
Get association timeouts sometimes with
Aruba APs |
|
4.1-Devpack 14.2 |
|
Neanderthal-Implement JAVA side and QED
CM interface |
|
|
DevPack does not install the locale
files |
|
4.1-Devpack
14 |
|
|
Support needed for Ext Device Package execution during ES/SR
install |
|
|
Patch Install says file replaced successfully whether done or
not |
|
|
Incorrect devpack version may allow newer devpack to be
overwritten |
|
|
Need to dump a list of running processes during installation. |
|
|
SR doesnt Init Database on replication failure detected scenario |
|
|
Device Default is updated when uninstalling ES/SR |
|
|
7961 device pack doesnt conatin proper device name on device
default |
|
|
7970/7971 |
|
|
Some items of Streaming Statistics from 7970 inconsistant w/
7960s |
|
|
Headset status indicator incorrect after 7970 reboot |
|
|
7970 incorrect LineType for some line buttons |
|
|
7970 not auto answer with headset after restart w/ headset light
on |
|
|
7970 not put active call in focus after incoming call
disconnected |
|
|
Phone restart with lower line rate of multicast/broadcast
traffic |
|
|
7970 fails to reregister after temporary WAN failure |
|
|
Ringer volume and other parameters are not configured aftr DSP
reset |
|
|
Sidetone on handset after reset |
|
|
7970 ICMP hard errors behavior changes |
|
|
7970 does not pick up the line when configured share line |
|
|
Extra ring heard when answering call after adjusting volume |
|
|
7970 RTPRx/RTPMRx URI syntax error allowed |
|
|
Possible deadlock situation in msg queue software |
|
|
Phone stuck at Configuring IP after prolonged CCM
disconnect/recon |
|
|
7970 drops host in DNS queries with subdomains |
|
|
Skate Security config menu opt 5 and 6 display wrong softkeys |
|
|
7970 RTPRx/RTPMRx URI opens invalid port by default |
|
|
Phone lockupCSCeg04380 |
|
|
7970 gethostbyname() does not return multiple IP addresses |
|
|
Mute signal heard on network |
|
|
When resetting the phone (**#**) PC loses network connectivity |
|
|
phone freezes during reboot with mqThread problem |
|
|
7970 phone failover to SRST takes more than 6 minutes |
|
|
Last digit not displayed when dialing from keypad |
|
|
JavaException using Navigate Keypad when call on hold |
|
|
Phone continue to stay with Requesting msg, cancel key has no
effect |
|
|
Java exception when 7970 configed with sidecar but none attached |
|
|
7970 Phone hangs on changing existing speed dial from phone
(CME) |
|
|
7970 crash when access protected URL 2nd time |
|
|
Onhook Dialing will not accept * or # as first digit |
|
|
Core dump of Sunvm.cnu when web-access is disabled & then
enabled |
|
|
Attempt to load diagnostic image file causes CNU reset |
|
|
Onhook Dialing is available when the phone is not registered |
|
|
7971 Multicast traffic dest to PC dropped by switch in phone. |
|
|
RTPTx-Stop not being executed |
|
|
7971 Unplugging and plug the ethernet cable, looses VLAN id |
|
|
Incorrect time for |
|
|
7970 drops keys if pressed too fast |
|
|
EM logged off profile keeps CFA icon |
|
|
Update handling of init.conf authentication settings |
|
|
SA Dereferencing pointer to freed memory in
Core/CNU/NetSys/udp.c |
|
|
SA expression must be a modifiable lvalue in
Core/Apps/cmds/ttrace/ |
|
|
SA Freeing pointer to already freed memory in
Core/Apps/daemons/DHC |
|
|
Broken autosensing on type-2 cabling (BU-3494) |
|
|
Makaha power request numbers are wrong |
|
|
ListenerManager allows for multiple listener |
|
|
Memory leak when press keys in predial |
|
|
Memory leak on startup in Call History property |
|
|
7971 phone not upgrading load, using device defaults. |
|
|
Phone reloads from nmap connect scan |
|
|
Stream.c flood reloads phone |
|
|
Failover fail on 7971 phone with CM 3.3.4(SR2) |
|
|
CVTA with 7970 messes up audio caps |
|
|
Phone stuck at Updating Software |
|
|
7970 - does not report Dest Unreach on sendto() |
|
|
Ethernet Disconnected message interferes with display (BU-3572) |
|
|
EndCall softkey doesnt work when CM down and other end had hit
Hold |
|
|
7971 Low power backlight needs to be 14 |
|
|
7970 - only retries 4 times after leaseT1 expires |
|
|
7970 hangs at config IP after reset |
|
|
Unexpected DHCP Renew after Release operation |
|
|
Shared System Threads create debugging problems |
|
|
Cut through on speaker phone take approx one sec |
|
|
Line button becomes useless after try dialing from call history |
|
|
Timer object should allow ITimerListeners to disable
timerCancelled |
|
|
7970 phone does not close the sockets automatically |
|
|
Mid-call video starts when active call is on mute |
|
|
7970 registering with CM when a active call is in place |
|
|
7971 phone reset after hold/resume duration |
|
|
Phone freeze after the extension mobility duration test was run |
|
|
7970 hangs intermittently while attempting EM login/logout |
|
|
XML parse error when text object with 4000 chars of text is sent |
|
|
Multiple restart from CM causes phone to freeze up |
|
|
http push may stop working |
|
|
Console shows CONSOLE TOO SLOW! Skipping 0 log files! |
|
|
Trace does not include key press information |
|
|
7971 Phone ignore vvlan information from switch port |
|
|
CVTA does not receive information on calls active when PC
plugged in |
|
|
Phone stuck after erase operation |
|
|
7971 does not comply with 802.3af power specification |
|
|
Phone can lose VLAN id with broadcast storms in the network |
|
|
PC attached to Phone loses network after multiple phone reload |
|
|
7971 phone re-boots when SYNC_RCVD state sttack was run |
|
|
Enable 802.3x flow control |
|
|
7970 plays loud comfortable noise when using G.729 codec |
|
|
Can not accept calls when call history is empty and in focus |
|
|
7970 change between daylight and standard time 1 hour too early |
|
|
Ringer stops working if press speaker right after adjust ring
volume |
|
|
Phone restarts exposes memory leak in the CallAgent module |
|
|
Call Info gone but voice path remains after brief Ethernet
disconnec |
|
|
Phone does not take Service URL w/ no label |
|
|
7971 w/ PC connected not operate in low power mode using ieee
inline |
|
|
7970 does not display missed call info after waking the display |
|
|
Phone stuck under simClient duration test |
|
|
7970 not alllow user to set IP Address Release as No |
|
|
7970 should display IP address released |
|
|
7970 missing date on console logs, status messages & debug
display |
|
|
7970 Autodial postpends to dialed # if display name contaions #s |
|
|
UI issue - services tab not coming to foreground in push
scenario |
|
|
7971 continuously resets if dot1x configured on switch interface |
|
|
ServicesChanging volume while RTPRx - softkey gets stuck at Save |
|
|
shownet command in cnush gives wrong output |
|
|
7971 accepts untagged packets while on a voice VLAN |
|
|
AbbrDial softkey appears on 7970 phone in CM3.x |
|
|
HTTP Push requests has successful response, but UI does not
display XML |
|
|
7970 does not properly reset causing sessions hung in LAST_ACK
on CCM |
|
|
7971 PC port does not show what is configured |
|
|
CP-7970 Fails to Boot up if 'switchport voice vlan dot1p' is
configured |
|
|
Bad voice on 7971 phone with 10% broadcast traffic |
|
|
Broadcast traffic throttling rate very low w/ load 69 on 7971
phone |
|
|
7971 phone only allows 10M (1%) broadcast traffic send to PC |
|
|
Phone does not pass thru all multicast traffic to PC |
|
|
7971 switch port stops transmitting frames causing phone to
unregister |
|
|
Network Statistics does not display Port 1 or Port 2 status
information |
|
|
7971 - PPU workaround does not set forced link speed correctly |
|
|
7971 - change CDP from a mgmt packet to a mcast packet in ATU |
|
|
7971 - enable VLAN 1 and VLAN 0 |
|
|
Phone crashed with in half an hour ,when XML boundary objects
script was |
|
|
Phone crashes for 200 calls per device case |
|
4.1-Devpack
13 |
|
|
Add QED support for 7911 |
|
|
Add 7985 QED support CCM versions 4.X and 5.X |
|
|
6624 |
|
|
6624 FXS port is unavalable for 2 mins after disabling and
enabling |
|
|
updation on 6624 does not reflect on port configuration page. |
|
|
FAC tone played continuously on using non default network locale |
|
|
6608/6624 |
|
|
Integrate 4.3.25 DSP firmware for 6608 |
|
|
6608 |
|
|
DicktracyRemove unnecessary DSP and MLPP related messages. |
|
|
6608-Dicktracy - Reduce trunk flash timer from 700ms to 400ms. |
|
4.1-Devpack
12 |
|
|
7935 |
|
|
7935 reboots on its own and couldnt reach tftp server
thereafter. |
|
|
7935/7936 |
|
|
7935 Autonegotiation does not work |
|
|
CCME 7936 conference call one way speech path and 7936 reboots |
|
|
7935 and 7936 stops ringing when 2 parties call it
simultaneously |
|
|
7936/7935 does not support JOIN feature of CCM 4.0 |
|
|
Ringer stops during incoming call when dial pressed under corp |
|
|
7935 is not accepting cass B netmask, if Ip addr is class C |
|
|
Inconsistent LCd and web page display |
|
|
On first call from 7935 gets one-way voice |
|
|
7935/7936 marking |
|
|
7935 will not register to ccm |
|
|
7936 will not register to ccm |
|
|
MOH is not heard during Transfer |
|
|
Not able to configure admin vlan via web interface. |
|
4.1-Devpack
11 |
|
|
7940/60 |
|
|
Remove vender specific parameter edit softkey from IP Phones |
|
|
Build phone loads |
|
|
Edit Dial push uris show Directories icon |
|
|
Unable to answer the call with linekey with shared lines |
|
|
14th digit disapears from IP Ph CFA Display after device reset |
|
|
Active call moves to the top of list after 9 seconds |
|
|
7960 Directories button sometimes opens Services URL |
|
|
7960 not showing correct display when same DN config on multiple
lin |
|
|
Phones To Be More Ambitious Towards Updating Firmware |
|
|
Phone web page not accessible after socket stress was run |
|
|
Cannot load diag image to 7940/7960 phone |
|
|
Cannot use # or * as first entry while onhook |
|
|
7960 should not automatically return to detail view from
overview |
|
|
With multiple held calls, line key should not resume oldest call |
|
|
With single on-hold call, line button should invoke overview
display |
|
|
Help for side car buttons throw an error |
|
|
CallManager TFTP Load=6.0(5)0 File Not Found when phone is reset |
|
|
Phone stuck in Configuring IP when Factory Reset, save settings
dhcp |
|
|
LA loader must check new LA size before burning to flash |
|
|
7960 crashes during XML POST with IPPhoneExecute |
|
|
Garbage help text at a certain key sequence |
|
|
An error at a certain key sequence |
|
|
Selecting directory entry with keypad doesnt update display |
|
|
7960 stops call timer when the CCM down |
|
|
Key rollover broken/missing digits when dialling |
|
|
Wrong association of 7940/60 help |
|
|
http//<phone> web page needs links to all streams info
during barge |
|
|
unable to answer 2nd line when speaker phone is disabled. |
|
|
7960 will not stay registered if ringlist.xml has invalid syntax |
|
|
Time display not updated on certain phone menus |
|
|
Changing Phone port # causes 7960s in Auth mode not to register |
|
|
C3PO Frame Buffer overflow causes COS3 packet drop |
|
|
IPSvcs-In case of missing refresh URL, dont show update softkey |
|
|
Extend scope of Msg/Dir URL to support icon menu |
|
|
IP Phones fails to recieve Audio Multicast Stream and gets reset |
|
|
Phone unable to get Ringlist.xml using Alternate TFTP |
|
|
Audio cut through delay during Call Waiting Answer |
|
|
RTP URI push during call requires user to cycle hook twice to
end |
|
|
Cisco 7940/7960 One-way audio and Freeze or Reset |
|
|
7940/60 DHCP Option 60 data different between big and little app |
|
|
URI SoftKey Dial resets the phone |
|
4.1-Devpack
10 |
|
|
Makaha needs to be added to 4.0 and 4.1 branches |
|
|
7902/05/12 |
|
|
7912 unable to be registered when User Locale is Japanese |
|
|
CP-7912G/7905G does not add 802.1p tag when no vlan is
configured. |
|
|
7905 and 7912 phones reboot with keep-conference feature |
|
|
OPickUp softkey does not work on 7912/7905 |
|
|
Multiple Calls on Dir Num calls were disconnected by CMs
failover |
|
|
7905 phone web server sends data in wrong HTTP version |
|
|
Select softkey in phrase 609 and 178 should be defined properly |
|
|
7912 and 7905 may crash and fail on re-registering |
|
|
Phone does not accept DHCP ACK sent to the broadcast address |
|
4.1-Devpack
09.1 |
|
|
Phone Config lacks precedence by MIC for 7970 phones |
|
4.1-Devpack
09 |
|
|
Due
to CSCeg77085 |
The 7940/60 default loads are not being set |
|
4.1-Devpack
08.2 |
|
|
7971 Device Devpak for CCM 4.0(2)sr1a has missing GUI |
|
4.1-Devpack
08.1 |
|
|
Device Protocol Options (T1-CAS/PRI) needed for VIC2-xMFT-T1 |
|
|
PI6 based features commit to CCM branches |
|
4.1-Devpack
08 |
|
|
7971 phone icon missing from CM Admin page |
|
|
7971 device type and load need to be added to CM releases |
|
4.1-Devpack
07.1 |
|
|
4.1(2) install adds device type for 7961 phone |
|
4.1-Devpack
07 |
|
|
7970/7971 display instance file and IP Phone Rules xml files
wrong |
|
|
6608
E1/T1 |
|
|
6608 Fax Relay debugs in D00404 firmware need to be same as
D00403 |
|
|
6608 inbound call mistaken for hookflash |
|
|
6608 Support for T1 CAS Guard time |
|
4.1-Devpack
06.2 |
|
|
Wrong WS-X6608 DSP load included with device load in 4.0(2a)SR1 |
|
4.1-Devpack
06 |
|
|
7905/7912 |
|
|
Switching back and forth between 2 calls makes the display
disappear |
|
|
Unable to switch between two active calls on 7912 |
|
|
ephone-template on 7912 removes message softkey |
|
|
7912 and 7905 may crash and fail on re-registering |
|
4.1-Devpack
05 |
|
|
6608 inbound call mistaken for hookflash |
|
|
7940/60 |
|
|
CallInfo CLI output not correct for different locale file |
|
|
7960 shared line predialled digits keep ringing, call ansd on
7970 |
|
|
Ip Phone doesnt accept option 66 with trailing dot in hostname |
|
|
Devices attached to phone lose network when PC VLAN enabled |
|
|
7960 does not display CallInfo if CCM down while in the call |
|
|
Unable to access protected URL from menu using custom softkey |
|
|
IP Phone recognize dialed number in wrong order |
|
|
Display shows only first 23 digits of a 24 digit DN |
|
|
Dial keys do not respond for 10 secs after pressing **# |
|
|
The link http// displays wrong DN |
|
|
Phone doesnt display the DN to be edited when editdial is
pressed |
|
|
Loader may fail - Application Invalid |
|
|
Phone should not cache failed credentials |
|
|
Phone may stop communicate with CCM or CAPF when using TLS |
|
|
7960 registered to CM 3.3 shows only one line while call on hold
|
|
|
Edit Dial on cancel shows Host Not Found |
|
|
AD Phone search always has word dial appended |
|
|
Extra ring heard when answering call after adjusting volume |
|
|
Called Party name is wrong when call is forwarded over ICT |
|
|
AutoDial Fails in a Active Call beetween IP Phone and MGCP
Endpoint |
|
|
I-Button doesnt give any Help for Ring Type Select/Default/Exit |
|
|
7960 struck with Booting Dsp alarm on its display |
|
|
Echo fades in and out when talking IP phone to IP phone |
|
|
7940/7960 IP phones showing as untrusted on
Cat3550,3560&4500 |
|
|
Phone fails to come up when wrong load Id is mentioned on phone
page |
|
|
Failback during cert gen not behaving properly |
4.1-Devpack 04 - skipped
|
4.1-Devpack
03 |
|
|
New 6608 modules will not register as a conference bridge or MTP
|
|
|
7970 |
|
|
7970 not put active call in focus after incoming call
disconnected |
|
|
Incorrect time for |
|
|
7970 drops keys if pressed too fast |
|
|
6608
T1/E1 |
|
|
Negative value for 6608 counter Total Rx RTP Lost Pkts |
|
|
6608 T1 CAS HookFlash is detected in |
|
|
6608 T1 CAS Glare Recovery may not work correctly |
|
|
configurable
non-linear comfort noise attenuation for 6608 |
|
|
6608 does not send RSIP forced to CCM when a reset comes from
CCM |
|
|
6608 T1 CAS Disconnect
Procedure Enhancements |
|
|
6608 T1 cas gateway fails to clear line for unallocated numbers |
|
|
Reverted
to 6.0(1)sr1 due to CSCeg24131 |
|
|
4.1-Devpack
02.1 |
|
|
Remove the extra are-you-sure from the ES/SR installs |
|
|
Uninstall Confirmation dialog should mention version reverting
to |
|
|
7970 |
|
|
4.1-Devpack
02 |
|
|
Cisco 2801 GW icon missing in Find and List GW page. |
|
|
7970 |
|
|
7970 incorrect behavior when try to dial from dir with call on
line |
|
|
7970 Override Auto Answer if Speaker Disable False doesnt work |
|
|
7970 Phone stops accepting HTTP connections |
|
|
MUTE Call Stat still shows Sender Packets incrementing mute is
on |
|
|
7970 dynamic call forward icon not updated properly after login |
|
|
Double selection of same ringer deselect it, also display
problems |
|
|
7970 Problems with ringer selections |
|
|
Ringing could not be stopped when call disconnected from far end
|
|
|
Jitter Tolerance new field added are not saved in conf file |
|
|
Receiving default config file does default previous cfg
parameters |
|
|
7970 Does not translate Australian Daylight Savings correctly |
|
|
TFTP Server address gone after Enabling DHCP w/Alternate |
|
|
7970 lists Load File as term70.default. User doesnt know load
name. |
|
|
No way to view call data on another line without answering call |
|
|
7970 Web page doesnt display network statistic info correctly |
|
|
Touching screen to wake up screen saver often invokes a soft key
|
|
|
Phone Resets swtiching from Services->Settings after loading
images |
|
|
Erase in Security Configuration menu only erases one item |
|
|
Redirected Authentication URL does not work |
|
|
Lifting handset in EditDial calls unedited number |
|
|
7970 doesnot failback from SRST when trying to make call |
|
|
Cannot open, close, reopen PC/SW Port Config |
|
|
7970 boot hangs with unrecognized timezone name |
|
|
7970 does not obey StationSetMicroModeMessage (mute microphone) |
|
|
CP-7970 does not populate CallingPartyName in Missed Calls Field
|
|
|
CP-7970 Time get out of sync if not used for extended period |
|
|
DEvice Config submenus donot have lock/unlock icon |
|
|
No alarms or phone logs when 2 of 4 locale files not found |
|
|
With 6 calls, resuming first causes 5th duration overwritten by
6th |
|
|
Pressing NewCall, EndCall with 7 calls on hold leaves no call
hilite |
|
|
call timer for barged call incorrect |
|
|
Add help for Call Agent Menu 1161 |
|
|
Add help for HTTP Menu 1162 |
|
|
Add help for Locale Menu 1163 |
|
|
Add help for Power Save Menu (1164) |
|
|
Add help for Ethernet Menu (1165) |
|
|
Add help for Media
Menu (1166) |
|
|
Add help for QoS Menu (1167) |
|
|
Add help for UI Menu (1168) |
|
|
Add help for Span PC Port (1169) |
|
|
Update path to admin tasks in online help |
|
|
DHCP gets hung on boot |
|
|
DHCP disable and CTL Erase enables DHCP |
|
|
GARP and VVLAN enable and disable reversed on display |
|
|
CTLFile stays unlocked still after re-dhcp |
|
|
7970 not able to save downloaded background image |
|
|
file auth error after factory reset |
|
|
Barge functionality not working for shared line between 7960
& 7970 |
|
|
7970 displays Mid-Atlantic time zone incorrect |
|
|
Default string is used as both softkey and parameter value |
|
|
HTTP request do not work on 7970, different from 7960/40 |
|
|
7970 stops sending CDP to attached Cisco VT Advantage PC |
|
|
7970 does not notice media disconnect when CVTA PC unplugs |
|
|
7970 Wont Register after upgrade to 3.3.4 |
|
|
7970 displays incorrect softkey sets when a call barged in |
|
|
RUS Line text label shows garbage on 7970 IP Phone |
|
|
Extension Mobility in 7970 shows English in all locales |
|
|
7970 hangs on request of LineInfo |
|
|
Erase softkey missing on Network Config menu |
|
|
7970 does not properly interpret parameter E |
|
|
7970 running 6.0.1 load does not show remote in use on shared
line |
|
|
XML services returned NullPointerException |
|
|
7970 continues to ring after call is disconnected |
|
|
PC behind the phone cannot authenticate into the network with
802.1x |
|
|
7970 displays NZ ( |
|
|
7970 CiscoIPPhoneInput Softkey gone if there is expire header in
asp |
|
|
XML post to 7970 using @ in password resets phone |
|
|
7970 phones query DNS instead of using proxy address for
services |
|
|
7970 phones query DNS instead of using proxy address for
services |
|
|
7970 voice quality degrade with UDP broadcast traffic. |
|
|
7970 shared line with out Barge causes phone to display
incorrectly |
|
|
One second refreshing of CiscoIPPhoneImageFile objects fails |
|
|
When in refresh XSI loop, hitting cancel does not cancel the
request |
|
|
7970 does not display Registration Rejected messages |
|
|
Softkeys disappear after cancle of callback on a held call |
|
|
7970 sends a 5-msec packet before a type13 packet (Hurt Confer.
Brdg |
|
|
7970 unregisters after unplugging PC from PC port |
|
|
7970 Has no serviceability to retain stack traces after
initialize |
|
|
7960 Call Info display behavior inconsistant |
|
|
TCP SYN vulnerability and Cisco phone end points |
|
|
Execute URL on 7970 is doing a DNS lookup |
|
|
7970 does not queue URLs from CiscoIPPhoneExecute |
|
|
Disable speaker does not work |
|
|
Pressing line button for active call doesnt go to overview
screen |
|
|
7970 causes continuous popping noise in a MCU conference (VAD=1)
|
|
|
7970 display / softkeys will freeze with high incoming call
traffic |
|
|
7970 display / softkeys will freeze with high incoming call
traffic |
|
|
7970 Select key is not greyed out on Ring menu |
|
|
7970 still display IPMA manager watch window after switch CCM |
|
|
7970 resets on pressing **#** while on corporate directory
screen |
|
|
Http request http/phones IP/CGI/LineInfo resets the phone |
|
|
7970 failed to recover from DSP error - DSP stopped by assertion
|
|
|
7970 added code to dump DSP message when its reponse faied to
return |
|
|
7970 will not allow a CVTA CAST connection |
|
|
Config file hunt on all tftp servers |
|
|
7970 stops accept HTTP after incorrect PUSH message |
|
|
7970 advertises wrong platform - CP-7 |
|
|
HTTP headers are case sensitive |
|
|
7970 not answering calls while in a menu |
|
|
7970 resets when accessing Network Statistics via web interface |
|
|
Date Time Group=Local time zone wrong in 7970 |
|
|
7970 If QRT key is pressed during active call softkeys disappear
|
|
|
Vendor String Inconsistant - 7970 |
|
|
Parche phone cannot upgrade when config file has secure SRST |
|
|
GARP is enabled in CM but showing GARP Enabled Yes on the phone |
|
|
Exit key not work when Dial from Directory on active line |
|
|
Skate 7970 not accepting untagged packets |
|
|
Incoming call droped if Dial from Directories |
|
|
7970 shows wrong softkey sets w/ Callback and incoming call |
|
|
7970 does not close CallBack application after dial from
CallBack |
|
|
7970 DHCP timer changed to 10 seconds |
|
|
7970 Phone ServicesURL handling disparity between 7970 and 7960 |
|
|
7970 UI freeze up under stress test |
|
|
Accessing web page in 7970 causes crash - possibly auth. problem
|
|
|
CP-7970 has worng values on XML config |
|
|
Pressing Services button causes phone to fail |
|
|
Phones stuck in Configuring IP after reset |
|
|
Soft resets freeze phone - memory leak |
|
|
Soft resetting causes flash memory error |
|
|
7970 should not make new call pressing line button w/ callback |
|
|
7970 shows CCM Down after restart from CCM w/ Active call |
|
|
Unable to answer call with help menu active unless Answer is
pressed |
|
|
Phone processing SIGIPCFG before phone app loaded |
|
|
7970 display error on Brightness menu after answer call |
|
|
7970 not auto answer with headset after restart w/ headset light
on |
|
|
7970 display error in Hold/Resume stress test |
|
|
7970 doesnt respond to Reset when shared line has Remote-In-Use
call |
|
|
Predial does not work when using offhook, line key, or speaker |
|
|
7970 crash w/ calls on 3 lines |
|
|
Skate SCCP messages cause phone to crash |
|
|
CNU doesnt reboot after 4 consecutive resets |
|
|
7970 does not take changes to DSCP for SCCP phone config field |
|
|
7970 phones unregister with Missing keepalives |
|
|
7970 lost registration to CCM during Hold/Resume duration test |
|
|
7970 timer thread cause 100% CPU usage leading to reset |
|
|
7970 displays blank/empty pages when receiving IPPhoneStatus
request |
|
|
Incorrect time for the Australian time zone AEST |
|
|
Java.lang.NullPoinerException while 7970 fail over |
|
|
7970G will not upgrade to newer load unless power-cycle |
|
|
Memory Leak on Restarts when there have been calls |
|
|
Null Pointer Exceptions when calls ended that are not visible |
|
|
Init AppStatus URI does not work and causes an exception |
|
|
7970 hangs randomly, requires reset. |
|
|
7970 stuck in unregistered state if network down w/ 150 held
calls |
|
|
Screen on 7970 phone got overwritten by page that has refresh
timer |
|
|
7970 locks up on boot up with failed assert (pos <=
t->maxPos) |
|
|
7970G - Pushing xml obj with long tags resulted in Phone reboot.
|
|
|
7970 becomes inoperable after firmware upgrade attempt |
|
|
7970 phone got resetted when user hit setting key |
|
|
7970 Sending http request to the phone freezes it |
|
|
CP-7970G - SELECT function works on touchscreen / not softkey |
|
|
7970 fails to reregister after temporary WAN failure |
|
|
Input of softkeys/linekeys/navkeys not shed if too high of rate |
|
|
CDP exits during link flap test |
|
|
CNU doesnt restart the VM when it exits |
|
|
7970 DSP reset due to libMTdoorCall select timeout |
|
|
Calls up when CCM connection is lost are not avail for reuse |
|
|
7970 can not boot after upgrade/downgrade stress test |
|
|
JVM not shut down properly when OS reboots due to rapid resets |
|
|
Need to increase size of syslog files to provide more debug data
|
|
|
Exceptions in the ITimerListener Dispatcher starves ObjectPool |
|
|
There is no way to determine the DHCP/CDP state from the GUI |
|
|
7970 hang after idle a while |
|
|
Memory Leak when Entering Menus |
|
|
nformation message displayed continuously on console |
|
|
7970 crash after Erase config several times |
|
|
DSP process signal traps (killed)-> doorCall select timeout |
|
|
When java.lang.OutOfMemoryError, init doesnt restart VM |
|
|
Can only answer call via Answer softkey after handle call
failure |
|
|
7970 has resize error during stress test |
|
|
7970 phone freezes when the XML objects are pushed |
|
|
7970 displays HI ( |
|
|
No packet sent when Silence suppression is turned on |
|
|
7970 displays empty callback page with no softkey |
|
|
In some Interfaces there is a potential for ObjectPool leaks |
|
|
# key displays error insted of its character set i.e. # + $ et
al. |
|
|
Message button becomes inactive after config message URL |
|
|
7970 - CDP can not acquire VLAN info |
|
|
RMS FULL Exception has no handler |
|
|
7970 sending wrong security capabilities to SRST |
|
|
7970 Hearing white noise when using codec g729 |
|
|
7970 Hangs on reset from CCM |
|
|
Phone freezes when a XML object is pushed and exit is pressed
for 6 |
|
|
Phone in requesting loop when XML objects are pushed sixth time |
|
|
7970 cannot parse non-URL proxy server address |
|
|
7970 doesnt mark services and HTTP packets correctly |
|
|
7970 stuck in Configuring IP when erase CTL with DHCP disabled |
|
|
7970 - DNS does not return from select errors |
|
|
Phone freezes during upgrading test with REL signed image |
|
|
7970 stops at Configuring IP after its config erased |
|
|
XsiDirectory Response causes memory leak |
|
|
7970 has Segmentation fault with its CCM switchport flap |
|
|
Wrong Security Icons shown for 7970 Phones in SRST mode. |
|
|
CiscoIPPhoneStatus object leaks graphic resources |
|
|
Hashtable.get() is returning an invalid Exception |
|
|
Phone continue to stay with Requesting msg, cancel key has no
effect |
|
|
No Audio & call is dropped for a G729 7970 call after CM
Restart |
|
|
Default keys shown while using custom keys |
|
|
Services Prompt line not cleared if new page has no prompt |
|
|
Multiple timezones are incorrect |
|
|
7902 |
|
|
Hold lamp of CP-7902G is not turned on during Transfer in SRST
mode. |
|
|
7902/05/12 |
|
|
Setting/Web access cannot be changed in different network |
|
|
7905/12 |
|
|
HUN - KATE file for 7905 does not display required chars |
|
|
HUN time on the phone display is not showing in Hungarian |
|
|
Can not pick up the latter reached call on 7912s shared line. |
|
|
7912 will not fallback from SRST to CCM when the CCM is back
online |
|
|
7912 Delayed Dial tone, Retransmit time |
|
|
7912/7905 do not implement the RTPMRx URI correctly |
|
|
Wrong CallInfo Display in CME environment |
|
|
7912G Japanese locale not working for Extension Mobility login/out
|
|
|
add OPickup for CCM 4.1(2) |
|
|
Display English Acct softkey in |
|
|
Missing dialed number after pressing service button |
|
|
7905XML Encode URL which is already encoded in some cases |
|
|
CP-7912G support controlling DSCP marking for voice bearer. |
|
|
7905/7912 should save setting/web access config |
|
|
CP-7912G does not control layer2 CoS value for skinny and RTP
packet |
|
|
Ext Mobility does not work for some dev profiles on 7912 &
7905 |
|
|
6608 |
|
|
configurable
non-linear comfort noise attenuation for 6608 |
|
4.1-Devpack
01 |
|
|
Giove CCM QED checkin - initial commit |
|
|
For removing 1880 from the CCM branches |
For
optimal performance, be sure that you use the Cisco IP Telephony Locale
Installer that is specific to the version of Cisco Unified CallManager that you
use. Be aware that all phrases may not
display in the desired locale when you upgrade to a different version of Cisco
Unified CallManager. Refer to the readme
file that is posted with the Cisco IP Telephony Locale Installer software on
the following URL for the complete list of supported languages: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/locinst/index.htm.
Each
release of Cisco Unified CallManager may support a different number of locales.
The full suite of Locale Installers that work with each applicable version of
Cisco Unified CallManager can be found on http://www.cisco.com
after the English version becomes available. You can download the Locale
Installers for all languages that are supported with Cisco CallManager from the
following location: http://www.cisco.com/kobayashi/sw-center/telephony/callmgr/locale-installer.shtml.
Note: When using locales, Cisco recommends that you wait until
the locale installer that specifically supports the version of Cisco Unified
CallManager that you use becomes available before you upgrade your system. Because some incompatibilities may exist
between releases, be sure to only use the locale installer that specifically
supports your version of Cisco Unified CallManager.
Cisco
documentation and additional literature are available on Cisco.com. Cisco also
provides several ways to obtain technical assistance and other technical
resources. These sections explain how to obtain technical information from
Cisco Systems.
Cisco.com
You can
access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can
access the Cisco website at this URL:
You can
access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
For
additional information about Cisco Unified CallManager, refer to the following
documentation:
To access
the documentation suite for voice products, navigate to the following URL: http://www.cisco.com/univercd/cc/td/doc/product/voice/.
To access
the latest software upgrades and related documentation for
Cisco Unified CallManager, navigate to the following URL and then choose the
applicable version: http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml.
Cisco documentation and additional literature are available
in a Documentation DVD package, which may have shipped with your product. The
Documentation DVD is updated regularly and may be more current than printed
documentation. The Documentation DVD package is available as a single unit.
Registered Cisco.com users (Cisco direct customers) can
order a Cisco Documentation DVD (product number DOC-DOCDVD=) from the Ordering
tool or Cisco Marketplace.
Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
Cisco Marketplace:
http://www.cisco.com/go/marketplace/
You can
find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can
order Cisco documentation in these ways:
You can
send comments about technical documentation to bug-doc@cisco.com.
You can
submit comments by using the response card (if present) behind the front cover
of your document or by writing to the following address:
Cisco
Systems
Attn:
Customer Document Ordering
170 West
Tasman Drive
San Jose,
CA 95134-9883
We
appreciate your comments.
Cisco Product
Security Overview
Cisco
provides a free online Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this
site, you can perform these tasks:
A current
list of security advisories and notices for Cisco products is available at this
URL: http://www.cisco.com/go/psirt
If you
prefer to see advisories and notices as they are updated in real time, you can
access a Product Security Incident Response Team Really Simple Syndication
(PSIRT RSS) feed from this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Cisco is committed to delivering secure products. We test
our products internally before we release them, and we strive to correct all
vulnerabilities quickly. If you think that you might have identified a
vulnerability in a Cisco product, contact PSIRT:
We encourage you to use Pretty Good Privacy (PGP) or a
compatible product to encrypt any sensitive information that you send to Cisco.
PSIRT can work from encrypted information that is compatible with PGP versions
2.x through 8.x. Never use a revoked or
an expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one that has the most recent creation date in this public key
server list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In an emergency, you can also reach PSIRT by telephone:
Obtaining
Technical Assistance
For all
customers, partners, resellers, and distributors who hold valid Cisco service
contracts, Cisco Technical Support provides 24-hour-a-day, award-winning
technical assistance. The Cisco Technical Support Website on Cisco.com features
extensive online support resources. In addition, Cisco Technical Assistance
Center (TAC) engineers provide telephone support. If you do not hold a valid
Cisco service contract, contact your reseller.
The Cisco
Technical Support Website provides online documents and tools for
troubleshooting and resolving technical issues with Cisco products and
technologies. The website is available 24 hours a day, 365 days a year, at this
URL:
http://www.cisco.com/techsupport
Access to
all tools on the Cisco Technical Support Website requires a Cisco.com user ID
and password. If you have a valid service contract but do not have a user ID or
password, you can register at this URL: http://tools.cisco.com/RPF/register/register.do
Note: Use the Cisco Product Identification (CPI) tool to
locate your product serial number before submitting a web or phone request for
service. You can access the CPI tool from the Cisco Technical Support Website
by clicking the Tools & Resources link under Documentation & Tools.
Choose Cisco Product Identification Tool from the Alphabetical Index drop-down
list, or click the Cisco Product Identification Tool link under Alerts &
RMAs. The CPI tool offers three search options: by product ID or model name; by
tree view; or for certain products, by copying and pasting show command output.
Search results show an illustration of your product with the serial number
label location highlighted. Locate the serial number label on your product and
record the information before placing a service call.
Using the
online TAC Service Request Tool is the fastest way to open S3 and S4 service
requests. (S3 and S4 service requests are those in which your network is
minimally impaired or for which you require product information.) After you
describe your situation, the TAC Service Request Tool provides recommended
solutions. If your issue is not resolved using the recommended resources, your
service request is assigned to a Cisco TAC engineer. The TAC Service Request
Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest
For S1 or
S2 service requests or if you do not have Internet access, contact the Cisco
TAC by telephone. (S1 or S2 service requests are those in which your production
network is down or severely degraded.) Cisco TAC engineers are assigned
immediately to S1 and S2 service requests to help keep your business operations
running smoothly.
To open a
service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a
complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request
Severity
To ensure
that all service requests are reported in a standard format, Cisco has
established severity definitions.
Severity 1
(S1)—Your network is “down,” or there is a critical impact to your business
operations. You and Cisco will commit all necessary resources around the clock
to resolve the situation.
Severity 2
(S2)—Operation of an existing network is severely degraded, or significant
aspects of your business operation are negatively affected by inadequate
performance of Cisco products. You and Cisco will commit full-time resources
during normal business hours to resolve the situation.
Severity 3
(S3)—Operational performance of your network is impaired, but most business
operations remain functional. You and Cisco will commit resources during normal
business hours to restore service to satisfactory levels.
Severity 4
(S4)—You require information or assistance with Cisco product capabilities,
installation, or configuration. There is little or no effect on your business
operations.
Obtaining
Additional Publications and Information
Information
about Cisco products, technologies, and network solutions is available from
various online and printed sources.
·
Cisco Marketplace
provides a variety of Cisco books, reference guides, and logo merchandise.
Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.com/go/marketplace/
·
Cisco Press publishes a wide range of general networking, training and
certification titles. Both new and experienced users will benefit from these
publications. For current Cisco Press titles and other information, go to Cisco
Press at this URL: http://www.ciscopress.com/
·
Packet magazine is the Cisco Systems technical user magazine for maximizing
Internet and networking investments. Each quarter, Packet delivers coverage of
the latest industry trends, technology breakthroughs, and Cisco products and
solutions, as well as network deployment and troubleshooting tips,
configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet
magazine at this URL: http://www.cisco.com/packet
·
iQ Magazine is the quarterly publication from Cisco Systems designed to
help growing companies learn how they can use technology to increase revenue,
streamline their business, and expand services. The publication identifies the
challenges facing these companies and the technologies to help solve them,
using real-world case studies and business strategies to help readers make
sound technology investment decisions. You can access iQ Magazine at this
URL: http://www.cisco.com/go/iqmagazine
·
Internet Protocol Journal is a quarterly journal published by Cisco Systems
for engineering professionals involved in designing, developing, and operating
public and private internets and intranets. You can access the Internet
Protocol Journal at this URL: http://www.cisco.com/ipj
·
World-class networking
training is available from Cisco. You can view current offerings at this
URL: http://www.cisco.com/en/US/learning/index.html
CCSP, the
Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of
Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and
iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar,
Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco
Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,
Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the
Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch,
Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS,
IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream,
Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network
Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX,
ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The
Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are
registered trademarks of Cisco Systems, Inc. and/or its affiliates in the
United States and certain other countries.
All other
trademarks mentioned in this document or Website are the property of their
respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (0501R)
Copyright ©
2008 Cisco Systems, Inc. All rights reserved.