Cisco Applied Mitigation Bulletin-
The Rockwell Automation FactoryTalk Services Platform contains multiple input validation vulnerabilities when processing specially crafted UDP datagrams. These vulnerabilities can be exploited remotely without authentication and without end-user interaction. Successful exploitation of these vulnerabilities could allow arbitrary code execution or result in a denial of service (DoS) condition. Repeated attempts to exploit these vulnerabilities could result in a sustained DoS condition.
The attack vectors for exploitation are through IP packets using the following protocols and ports:
- UDP port 4444
- UDP port 4445
-
Cisco IOS Software can provide effective means of exploit prevention using the following methods:
- Transit access control lists (tACLs)
- Unicast Reverse Path Forwarding (uRPF)
- IP source guard (IPSG)
These protection mechanisms filter and drop, as well as verify the source IP address of, packets that are attempting to exploit these vulnerabilities.
The proper deployment and configuration of uRPF provides an effective means of protection against attacks that use packets with spoofed source IP addresses. Unicast RPF should be deployed as close to all traffic sources as possible.
The proper deployment and configuration of IPSG provides an effective means of protection against spoofed packets at the access layer.
Effective means of exploit prevention can also be provided by Cisco ASA 5500 Series Adaptive Security Appliance, Cisco Catalyst 6500 Series ASA Services Module (ASASM), and the Firewall Services Module (FWSM) for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers using the following methods:
- tACLs
- uRPF
These protection mechanisms filter and drop, as well as verify the source IP address of, packets that are attempting to exploit the vulnerabilities.
Cisco IOS NetFlow records can provide visibility into network-based exploitation attempts.
Cisco IOS Software, Cisco ASA, Cisco ASASM, and Cisco FWSM firewalls can provide visibility through syslog messages and counter values displayed in the output from show commands.
The Cisco Security Manager can also provide visibility through incidents, queries, and event reporting.
-
Organizations are advised to follow their standard risk evaluation and mitigation processes to determine the potential impact of these vulnerabilities. Triage refers to sorting projects and prioritizing efforts that are most likely to be successful. Cisco has provided documents that can help organizations develop a risk-based triage capability for their information security teams. Risk Triage for Security Vulnerability Announcements and Risk Triage and Prototyping can help organizations develop repeatable security evaluation and response processes.
-
Caution: The effectiveness of any mitigation technique depends on specific customer situations such as product mix, network topology, traffic behavior, and organizational mission. As with any configuration change, evaluate the impact of this configuration prior to applying the change.
Specific information about mitigation and identification is available for these devices:
- Cisco IOS Routers and Switches
- Cisco IOS NetFlow and Cisco IOS Flexible NetFlow
- Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls
- Cisco Security Manager
Cisco IOS Routers and Switches
Mitigation: Transit Access Control Lists
To protect the network from traffic that enters the network at ingress access points, which may include Internet connection points, partner and supplier connection points, or VPN connection points, administrators are advised to deploy transit access control lists (tACLs) to perform policy enforcement. Administrators can construct a tACL by explicitly permitting only authorized traffic to enter the network at ingress access points or permitting authorized traffic to transit the network in accordance with existing security policies and configurations. A tACL workaround cannot provide complete protection against these vulnerabilities when the attack originates from a trusted source address.
The tACL policy denies unauthorized packets on UDP port 4444 and 4445 that are sent to affected devices. In the following example, 192.168.60.0/24 represents the IP address space that is used by the affected devices, and the host at 192.168.100.1 is considered a trusted source that requires access to the affected devices. Care should be taken to allow required traffic for routing and administrative access prior to denying all unauthorized traffic.
Additional information about tACLs is available in Transit Access Control Lists: Filtering at Your Edge.
!-- Include explicit permit statements for trusted sources !-- that require access on the vulnerable ports ! access-list 150 permit udp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 4444 access-list 150 permit udp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 4445 ! !-- The following vulnerability-specific access control entries !-- (ACEs) can aid in identification of attacks against the Rockwell Automation !-- FactoryTalk Services Platform input validation vulnerabilities ! access-list 150 deny udp any 192.168.60.0 0.0.0.255 eq 4444 access-list 150 deny udp any 192.168.60.0 0.0.0.255 eq 4445 ! !-- Permit or deny all other Layer 3 and Layer 4 traffic in accordance !-- with existing security policies and configurations ! !-- Explicit deny for all other IP traffic ! access-list 150 deny ip any any ! !-- Apply tACLs to interfaces in the ingress direction ! interface GigabitEthernet0/0 ip access-group 150 in
Note that filtering with an interface access list will elicit the transmission of ICMP unreachable messages back to the source of the filtered traffic. Generating these messages could have the undesired effect of increasing CPU utilization on the device. In Cisco IOS Software, ICMP unreachable generation is limited to one packet every 500 milliseconds by default. ICMP unreachable message generation can be disabled using the interface configuration commands no ip unreachables. ICMP unreachable rate limiting can be changed from the default using the global configuration commands ip icmp rate-limit unreachableinterval-in-ms.
Identification: Transit Access Control Lists
After the administrator applies the tACL to an interface, show ip access-lists commands will identify the number of packets on UDP ports 4444 and 4445 that have been filtered. Administrators are advised to investigate filtered packets to determine whether they are attempts to exploit these vulnerabilities. Example output for show ip access-lists 150:
router#show ip access-lists 150 Extended IP access list 150 10 permit udp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 4444 20 permit udp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 4445 30 deny udp any 192.168.60.0 0.0.0.255 eq 4444 (26 matches) 40 deny udp any 192.168.60.0 0.0.0.255 eq 4445 (16 matches) 50 deny ip any any router#In the preceding example, access list 150 has dropped the following packets:
- 26 packets on UDP port 4444 for access control list entry (ACE) line 30.
- 16 packets on UDP port 4445 for access control list entry (ACE) line 40.
For additional information about investigating incidents using ACE counters and syslog events, reference the Identifying Incidents Using Firewall and IOS Router Syslog Events Cisco Security white paper.
Administrators can use Embedded Event Manager to provide instrumentation when specific conditions are met, such as ACE counter hits. The Cisco Security white paper Embedded Event Manager in a Security Context provides additional details about how to use this feature.
Identification: Access List Logging
The log and log-input access control list (ACL) option will cause packets that match specific ACEs to be logged. The log-input option enables logging of the ingress interface in addition to the packet source and destination IP addresses and ports.
Caution: Access control list logging can be very CPU intensive and must be used with extreme caution. Factors that drive the CPU impact of ACL logging are log generation, log transmission, and process switching to forward packets that match log-enabled ACEs.
For Cisco IOS Software, the ip access-list logging interval interval-in-ms command can limit the effects of process switching induced by IPv4 ACL logging. The logging rate-limit rate-per-second [except loglevel] command limits the impact of log generation and transmission.
The CPU impact from ACL logging can be addressed in hardware on the Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers with Supervisor Engine 720 or Supervisor Engine 32 using optimized ACL logging.
For additional information about the configuration and use of ACL logging, reference the Understanding Access Control List Logging Cisco Security white paper.
Mitigation: Spoofing Protection
Unicast Reverse Path Forwarding
The vulnerabilities described in this document can be exploited by spoofed IP packets. Administrators can deploy and configure Unicast Reverse Path Forwarding (uRPF) as a protection mechanism against spoofing.
uRPF is configured at the interface level and can detect and drop packets that lack a verifiable source IP address. Administrators should not rely on uRPF to provide complete spoofing protection because spoofed packets may enter the network through a uRPF-enabled interface if an appropriate return route to the source IP address exists. Administrators are advised to take care to ensure that the appropriate uRPF mode (loose or strict) is configured during the deployment of this feature because it can drop legitimate traffic that is transiting the network. In an enterprise environment, uRPF may be enabled at the Internet edge and the internal access layer on the user-supporting Layer 3 interfaces.
Additional information is available in the Unicast Reverse Path Forwarding Loose Mode Feature Guide.
For additional information about the configuration and use of uRPF, reference the Understanding Unicast Reverse Path Forwarding Cisco Security white paper.
IP Source Guard
IP source guard (IPSG) is a security feature that restricts IP traffic on nonrouted, Layer 2 interfaces by filtering packets based on the DHCP snooping binding database and manually configured IP source bindings. Administrators can use IPSG to prevent attacks from an attacker who attempts to spoof packets by forging the source IP address and/or the MAC address. When properly deployed and configured, IPSG coupled with strict mode uRPF provides the most effective means of spoofing protection for the vulnerabilities described in this document.
Additional information about the deployment and configuration of IPSG is available in Configuring DHCP Features and IP Source Guard.
Identification: Spoofing Protection Using Unicast Reverse Path Forwarding
With uRPF properly deployed and configured throughout the network infrastructure, administrators can use the show cef interface type slot/port internal, show ip interface, show cef drop, show ip cef switching statistics feature, and show ip traffic commands to identify the number of packets that uRPF has dropped.
Note: Beginning with Cisco IOS Software Release 12.4(20)T, the command show ip cef switching has been replaced by show ip cef switching statistics feature.
Note: The show command | begin regex and show command | include regex command modifiers are used in the following examples to minimize the amount of output that administrators will need to parse to view the desired information. Additional information about command modifiers is in the show commandsections of the Cisco IOS Configuration Fundamentals Command Reference.
router#show cef interface GigabitEthernet 0/0 internal | include drop ip verify: via=rx (allow default), acl=0, drop=18, sdrop=0 router#
Note: show cef interface type slot/port internal is a hidden command that must be fully entered at the command-line interface. Command completion is not available for it.
router#show cef drop CEF Drop Statistics Slot Encap_fail Unresolved Unsupported No_route No_adj ChkSum_Err RP 27 0 0 18 0 0 router# router#show ip interface GigabitEthernet 0/0 | begin verify IP verify source reachable-via RX, allow default, allow self-ping 18 verification drops 0 suppressed verification drops router# router#show ip cef switching statistics feature IPv4 CEF input features:
Path Feature Drop Consume Punt Punt2Host Gave route
RP PAS uRPF 18 0 0 0 0 Total 18 0 0 0 0 -- CLI Output Truncated -- router# router#show ip traffic | include RPF 18 no route, 18 unicast RPF, 0 forced drop router#Cisco IOS NetFlow and Cisco IOS Flexible NetFlow
Identification: IPv4 Traffic Flow Identification Using Cisco IOS NetFlow
Administrators can configure Cisco IOS NetFlow on Cisco IOS routers and switches to aid in the identification of IPv4 traffic flows that may be attempts to exploit the vulnerabilities described in this document. Administrators are advised to investigate flows to determine whether they are attempts to exploit the vulnerabilities or whether they are legitimate traffic flows.
router#show ip cache flow IP packet size distribution (90784136 total packets): 1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 .000 .698 .011 .001 .004 .005 .000 .004 .000 .000 .003 .000 .000 .000 .000 512 544 576 1024 1536 2048 2560 3072 3584 4096 4608 .000 .001 .256 .000 .010 .000 .000 .000 .000 .000 .000 IP Flow Switching Cache, 4456704 bytes 1885 active, 63651 inactive, 59960004 added 129803821 ager polls, 0 flow alloc failures Active flows timeout in 30 minutes Inactive flows timeout in 15 seconds IP Sub Flow Cache, 402056 bytes 0 active, 16384 inactive, 0 added, 0 added to flow 0 alloc failures, 0 force free 1 chunk, 1 chunk added last clearing of statistics never Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec) -------- Flows /Sec /Flow /Pkt /Sec /Flow /Flow TCP-Telnet 11393421 2.8 1 48 3.1 0.0 1.4 TCP-FTP 236 0.0 12 66 0.0 1.8 4.8 TCP-FTPD 21 0.0 13726 1294 0.0 18.4 4.1 TCP-WWW 22282 0.0 21 1020 0.1 4.1 7.3 TCP-X 719 0.0 1 40 0.0 0.0 1.3 TCP-BGP 1 0.0 1 40 0.0 0.0 15.0 TCP-Frag 70399 0.0 1 688 0.0 0.0 22.7 TCP-other 47861004 11.8 1 211 18.9 0.0 1.3 UDP-DNS 582 0.0 4 73 0.0 3.4 15.4 UDP-NTP 287252 0.0 1 76 0.0 0.0 15.5 UDP-other 310347 0.0 2 230 0.1 0.6 15.9 ICMP 11674 0.0 3 61 0.0 19.8 15.5 IPv6INIP 15 0.0 1 1132 0.0 0.0 15.4 GRE 4 0.0 1 48 0.0 0.0 15.3 Total: 59957957 14.8 1 196 22.5 0.0 1.5 SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts Gi0/0 192.168.10.201 Gi0/1 192.168.60.102 11 0984 115C 1 Gi0/0 192.168.11.54 Gi0/1 192.168.60.158 11 0911 115D 3 Gi0/1 192.168.150.60 Gi0/0 10.89.16.226 06 0016 12CA 1In the preceding example, there are multiple flows on UDP ports 4444 (hex value 115C) and 4445 (hex value 115D).
This traffic is sourced from and sent to addresses within the 192.168.60.0/24 address block, which is used by affected devices. The packets in these flows may be spoofed and may indicate an attempt to exploit these vulnerabilities. Administrators are advised to compare these flows to baseline utilization for traffic sent on UDP ports 4444 and 4445 and also investigate the flows to determine whether they are sourced from untrusted hosts or networks.
As shown in the following example, to view only the traffic flows for packets on UDP ports 4444 (hex value 115C) and 4445 (hex value 115D), use the show ip cache flow | include SrcIf|_11_.*(115C|115D) command to display the related Cisco NetFlow records:UDP Flows
router#show ip cache flow | include SrcIf|_11_.*(115C|115D) SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts Gi0/0 192.168.10.201 Gi0/1 192.168.60.102 11 0984 115C 1 Gi0/0 192.168.11.54 Gi0/1 192.168.60.158 11 0911 115D 3
Identification: IPv4 Traffic Flow Identification Using Cisco IOS Flexible NetFlow
Introduced in Cisco IOS Software Releases 12.2(31)SB2 and 12.4(9)T, Cisco IOS Flexible NetFlow improves original Cisco NetFlow by adding the capability to customize the traffic analysis parameters for the administrator's specific requirements. Original Cisco NetFlow uses a fixed seven tuples of IP information to identify a flow, whereas Cisco IOS Flexible NetFlow allows the flow to be user defined. It facilitates the creation of more complex configurations for traffic analysis and data export by using reusable configuration components.
The following example output is from a Cisco IOS device that is running a version of Cisco IOS Software in the 15.1T train. Although the syntax will be almost identical for the 12.4T and 15.0 trains, it may vary slightly depending on the actual Cisco IOS release being used. In the following configuration, Cisco IOS Flexible NetFlow will collect information on interface GigabitEthernet0/0 for incoming IPv4 flows based on source IPv4 address, as defined by the match ipv4 source address key field statement. Cisco IOS Flexible NetFlow will also include nonkey field information about source and destination IPv4 addresses, protocol, ports (if present), ingress and egress interfaces, and packets per flow.
! !-- Configure key and nonkey fields !-- in the user-defined flow record ! flow record FLOW-RECORD-ipv4 match ipv4 source address collect ipv4 protocol collect ipv4 destination address collect transport source-port collect transport destination-port collect interface input collect interface output collect counter packets ! !-- Configure the flow monitor to !-- reference the user-defined flow !-- record ! flow monitor FLOW-MONITOR-ipv4 record FLOW-RECORD-ipv4 ! !-- Apply the flow monitor to the interface !-- in the ingress direction ! interface GigabitEthernet0/0 ip flow monitor FLOW-MONITOR-ipv4 input
The Cisco IOS Flexible NetFlow flow output is as follows:
router#show flow monitor FLOW-MONITOR-ipv4 cache format table Cache type: Normal Cache size: 4096 Current entries: 6 High Watermark: 1 Flows added: 9181 Flows aged: 9175 - Active timeout ( 1800 secs) 9000 - Inactive timeout ( 15 secs) 175 - Event aged 0 - Watermark aged 0 - Emergency aged 0 IPV4 SRC ADDR ipv4 dst addr trns src port trns dst port intf input intf output pkts ip prot ============== ============== ============= ============= ========== =========== ==== ======= 192.168.10.201 192.168.60.102 1456 4444 Gi0/0 Gi0/1 1128 17 192.168.11.54 192.168.60.158 1563 4445 Gi0/0 Gi0/1 2212 17 192.168.150.60 10.89.16.226 2567 443 Gi0/0 Gi0/1 13 6In the preceding example, there are multiple flows on UDP ports 4444 and 4445.
This traffic is sourced from and sent to addresses within the 192.168.60.0/24 address block, which is used by affected devices. The packets in these flows may be spoofed and may indicate an attempt to exploit these vulnerabilities. Administrators are advised to compare these flows to baseline utilization for traffic sent on UDP portd 4444 and 4445 and also investigate the flows to determine whether they are sourced from untrusted hosts or networks.
To view only the packets on UDP port 4444 and 4445, use the show flow monitor FLOW-MONITOR-ipv4 cache format table | include IPV4 DST ADDR |_(4444|4445)_.*_17 command to display the related NetFlow records.
For more information about Cisco IOS Flexible NetFlow, refer to Flexible Netflow Configuration Guide, Cisco IOS Release 15.1M&T and Cisco IOS Flexible NetFlow Configuration Guide, Release 12.4T.
Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls
Mitigation: Transit Access Control Lists
To protect the network from traffic that enters the network at ingress access points, which may include Internet connection points, partner and supplier connection points, or VPN connection points, administrators are advised to deploy tACLs to perform policy enforcement. Administrators can construct a tACL by explicitly permitting only authorized traffic to enter the network at ingress access points or permitting authorized traffic to transit the network in accordance with existing security policies and configurations. A tACL workaround cannot provide complete protection against these vulnerabilities when the attack originates from a trusted source address.
The tACL policy denies unauthorized packets on UDP ports 4444 and 4445 that are sent to affected devices. In the following example, 192.168.60.0/24 is the IP address space that is used by the affected devices, and the host at 192.168.100.1 is considered a trusted source that requires access to the affected devices. Care should be taken to allow required traffic for routing and administrative access prior to denying all unauthorized traffic.
Additional information about tACLs is in Transit Access Control Lists: Filtering at Your Edge.
! !-- Include explicit permit statements for trusted sources !-- that require access on the vulnerable protocols and ports ! access-list tACL-Policy extended permit udp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 4444 access-list tACL-Policy extended permit udp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 4445 ! !-- The following vulnerability-specific ACEs !-- can aid in identification of attacks ! access-list tACL-Policy extended deny udp any 192.168.60.0 255.255.255.0 eq 4444 access-list tACL-Policy extended deny udp any 192.168.60.0 255.255.255.0 eq 4445 ! !-- Permit or deny all other Layer 3 and Layer 4 traffic in accordance !-- with existing security policies and configurations ! !-- Explicit deny for all other IP traffic ! access-list tACL-Policy extended deny ip any any ! !-- Apply tACLs to interfaces in the ingress direction ! access-group tACL-Policy in interface outside
Identification: Transit Access Control Lists
After the tACL has been applied to an interface, administrators can use the show access-list command to identify the number of packets on UDP port 4444 and 4445 that have been filtered. Administrators are advised to investigate filtered packets to determine whether they are attempts to exploit these vulnerabilities. Example output for show access-list tACL-Policy follows:
firewall#show access-list tACL-Policy access-list tACL-Policy; 5 elements; name hash: 0x3452703d access-list tACL-Policy line 1 extended permit udp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 4444 (hitcnt=31) access-list tACL-Policy line 2 extended permit udp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 4445 (hitcnt=31) access-list tACL-Policy line 3 extended deny udp any 192.168.60.0 255.255.255.0 eq 4444 (hitcnt=14) access-list tACL-Policy line 4 extended deny udp any 192.168.60.0 255.255.255.0 eq 4445 (hitcnt=24) access-list tACL-Policy line 5 extended deny ip any any (hitcnt=8)In the preceding example, access list tACL-Policy has dropped the following packets:
- 14 packets on UDP port 4444
- 24 packets on UDP port 4445
In addition, syslog message 106023 can provide valuable information, which includes the source and destination IP address, the source and destination port numbers, and the IP protocol for the denied packet.
Identification: Firewall Access List Syslog Messages
Firewall syslog message 106023 will be generated for packets denied by an access control entry (ACE) that does not have the log keyword present. Additional information about this syslog message is in Cisco ASA 5500 Series System Log Message, 8.2 - 106023.
Information about configuring syslog for the Cisco ASA 5500 Series Adaptive Security Appliance is in Monitoring - Configuring Logging. Information about configuring syslog on the Cisco Catalyst 6500 Series ASA Services Module is in Configuring Logging. Information about configuring syslog on the FWSM for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers is in Monitoring the Firewall Services Module.
In the following example, the show logging | grep regex command extracts syslog messages from the logging buffer on the firewall. These messages provide additional information about denied packets that could indicate potential attempts to exploit the vulnerabilities that are described in this document. It is possible to use different regular expressions with the grep keyword to search for specific data in the logged messages.
Additional information about regular expression syntax is in Creating a Regular Expression.
firewall#show logging | grep 106023 April 12 2013 00:15:13: %ASA-4-106023: Deny udp src outside:192.0.2.18/2944 dst inside:192.168.60.191/4444 by access-group "tACL-Policy" April 12 2013 00:15:13: %ASA-4-106023: Deny udp src outside:192.0.2.200/2945 dst inside:192.168.60.33/4445 by access-group "tACL-Policy firewall#In the preceding example, the messages logged for the tACL tACL-Policy show potentially spoofed packets on UDP ports 4444 and 4445 sent to the address block assigned to devices.
Additional information about syslog messages for Cisco ASA Series Adaptive Security Appliances is in Cisco ASA 5500 Series System Log Messages, 8.2. Additional information about syslog messages for Cisco Catalyst 6500 Series ASA Services Module is in the Analyzing Syslog Messages section of theCisco ASASM CLI Configuration Guide. Additional information about syslog messages for the Cisco FWSM is in Catalyst 6500 Series Switch and Cisco 7600 Series Router Firewall Services Module Logging System Log Messages.
For additional information about investigating incidents using syslog events, reference the Identifying Incidents Using Firewall and IOS Router Syslog Events Cisco Security white paper.
Mitigation: Spoofing Protection Using Unicast Reverse Path Forwarding
The vulnerabilities that are described in this document can be exploited by spoofed IP packets. Administrators can deploy and configure uRPF as a protection mechanism against spoofing.
uRPF is configured at the interface level and can detect and drop packets that lack a verifiable source IP address. Administrators should not rely on uRPF to provide complete spoofing protection because spoofed packets may enter the network through a uRPF-enabled interface if an appropriate return route to the source IP address exists. In an enterprise environment, uRPF may be enabled at the Internet edge and at the internal access layer on the user-supporting Layer 3 interfaces. Starting in 12.(13)T, uRPF is also supported for IPv6.
For additional information about the configuration and use of uRPF, reference the Cisco Security Appliance Command Reference for ip verify reverse-path and the Understanding Unicast Reverse Path Forwarding Cisco Security white paper.
Identification: Spoofing Protection Using Unicast Reverse Path Forwarding
Firewall syslog message 106021 will be generated for packets denied by uRPF. Additional information about this syslog message is in Cisco ASA 5500 Series System Log Message, 8.2 - 106021.
Information about configuring syslog for the Cisco ASA 5500 Series Adaptive Security Appliance is in Monitoring - Configuring Logging. Information about configuring syslog for the Cisco Catalyst 6500 Series ASA Services Module is in Configuring Logging. Information about configuring syslog on the FWSM for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers is in Monitoring the Firewall Services Module.
In the following example, the show logging | grep regex command extracts syslog messages from the logging buffer on the firewall. These messages provide additional information about denied packets that could indicate potential attempts to exploit the vulnerabilities that are described in this document. It is possible to use different regular expressions with the grep keyword to search for specific data in the logged messages.
Additional information about regular expression syntax is in Creating a Regular Expression.
firewall#show logging | grep 106021 April 12 2013 00:15:13: %ASA-1-106021: Deny UDP reverse path check from 192.168.60.1 to 192.168.60.100 on interface outside April 12 2013 00:15:13: %ASA-1-106021: Deny UDP reverse path check from 192.168.60.1 to 192.168.60.100 on interface outsideThe show asp drop command can also identify the number of packets that the uRPF feature has dropped, as shown in the following example:
firewall#show asp drop frame rpf-violated Reverse-path verify failed 11 firewall#
In the preceding example, uRPF has dropped 11 IP packets received on interfaces with uRPF configured. Absence of output indicates that the uRPF feature on the firewall has not dropped packets.
For additional information about debugging accelerated security path dropped packets or connections, reference the Cisco Security Appliance Command Reference for show asp drop.
Cisco Security Manager
Identification: Cisco Security Manager
Cisco Security Manager, Event Viewer
Beginning in software version 4.0, Cisco Security Manager can collect syslogs from Cisco firewalls and Cisco IPS devices and provides the Event Viewer, which can query for events that are related to the vulnerabilities that are described in this document.
Using the following filters in the Firewall Denied Events predefined view in the Event Viewer provides all captured Cisco firewall access list deny syslog messages that could indicate potential attempts to exploit the vulnerabilities that are described in this document.
- Use the Destination event filter to filter network objects that contain the IP address space that is used by the affected devices (for example, IPv4 address range 192.168.60.0/24 on UDP ports 4444 and 4445)
- Use the Destination Service event filter to filter objects that contain UDP ports 4444 and 4445
An Event Type ID filter can be used with the Firewall Denied Events predefined view in the Event Viewer to filter the syslog IDs shown in the following list to provide all captured Cisco firewall deny syslog messages that could indicate potential attempts to exploit the vulnerabilities that are described in this document:
- ASA-4-106021 (uRPF spoofing)
- ASA-4-106023 (ACL deny)
For more information about Cisco Security Manager Events, refer to the Filtering and Querying Events section of the Cisco Security Manager User Guide.
Cisco Security Manager Report Manager
Beginning in software version 4.1, Cisco Security Manager will generate a comprehensive report that ranks the count of the alerts fired for the signature of interest compared to the total sum of all signature alerts shown in the report.
Also in the Report Manager, the Top Services report can be used with the following configuration to generate a report of events that indicate potential attempts to exploit the vulnerabilities that are described in this document:
- Use the Destination IP network filter to filter network objects that contain the IP address space that is used by the affected devices (for example, IPv4 address range 192.168.60.0/24 on UDP ports 4444 and 4445)
- Set an action of Deny on the Criteria settings page
For more information about Cisco Security Manager IPS Event Reporting, refer to the Understanding IPS Top Reports section of the Cisco Security Manager User Guide.
Identification: Event Management System Partner Events
Cisco works with industry-leading Security Information and Event Management (SIEM) companies through the Cisco Developer Network. This partnership helps Cisco deliver validated and tested SIEM systems that address business concerns such as long-term log archiving and forensics, heterogeneous event correlation, and advanced compliance reporting. Security Information and Event Management partner products can be leveraged to collect events from Cisco devices and then query the collected events for the incidents created by a Cisco IPS signature or deny syslog messages from firewalls that could indicate potential attempts to exploit the vulnerabilities that are described in this document. The queries can be made by Sig ID and Syslog ID as shown in the following list:
- ASA-4-106021 (uRPF spoofing)
- ASA-4-106023 (ACL deny)
For more information about SIEM partners, refer to the Security Management System website.
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
-
Show LessVersion Description Section Date 1 Initial Release 2013-April-12 20:55 GMT
-
Complete information on reporting security vulnerabilities in Cisco products, obtaining assistance with security incidents, and registering to receive security information from Cisco, is available on Cisco's worldwide website at https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html. This includes instructions for press inquiries regarding Cisco security notices. All Cisco security advisories are available at http://www.cisco.com/go/psirt.
-
The security vulnerability applies to the following combinations of products.
Primary Products Rockwell Automation FactoryTalk Services Platform CPR9 (Base, SR1, SR2, SR3, SR4, SR5, SR5.1, SR6) RSLinx Enterprise CPR9 (Base, SR1, SR2, SR3, SR4, SR5, SR5.1, SR6)
Associated Products
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE ALERTS AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products