Cisco Response

• Microsoft announced eight security bulletins that address 19 vulnerabilities as part of the monthly security bulletin release on November 12, 2013. A summary of these bulletins is on the Microsoft website at http://technet.microsoft.com/en-us/security/bulletin/ms13-nov. This document provides identification and mitigation techniques that administrators can deploy on Cisco network devices.

  The vulnerabilities that have a client software attack vector, can be exploited locally on the vulnerable device, require user interaction, can be exploited using web-based attacks (these include but are not limited to cross-site scripting, phishing, and web-based email threats) or email attachments are in the following list:

  • MS13-088
  • MS13-089
  • MS13-090
  • MS13-091
  • MS13-092
  • MS13-093
  • MS13-094
  • MS13-095

  The vulnerabilities that have a network mitigation are in the following list. Cisco devices provide several countermeasures for the vulnerabilities that have a network attack vector, which will be discussed in detail later in this document.

  • MS13-089
  • MS13-090
  • MS13-091

  Information about affected and unaffected products is available in the respective Microsoft advisories and the Cisco Alerts that are referenced in Cisco Event Response: Microsoft Security Bulletin Release for November 2013.

  In addition, multiple Cisco products use Microsoft operating systems as their base operating system. Cisco products that may be affected by the vulnerabilities described in the referenced Microsoft advisories are detailed in the "Associated Products" table in the "Product Sets" section.

Vulnerability Characteristics

• MS13-089, Vulnerability in Windows Graphics Device Interface Could Allow Remote Code Execution (2876331): This vulnerability has been assigned Common Vulnerabilities and Exposures (CVE) identifier CVE-2013-3901. This vulnerability can be exploited remotely with authentication and requires user interaction. Successful exploitation of this vulnerability may allow remote code execution. The attack vector for exploitation of these vulnerabilities is through HTTP packets that typically use TCP port 80 but may also use TCP ports 3128, 8000, 8010, 8080, 8888, and 24326.

  MS13-090, Cumulative Security Update of ActiveX Kill Bits (2508272): This vulnerability has been assigned Common Vulnerabilities and Exposures (CVE) identifier CVE-2013-3918. This vulnerability can be exploited remotely without authentication and requires user interaction. Successful exploitation of this vulnerability may allow arbitrary code execution. The attack vector for exploitation of this vulnerability is through HTTP packets that typically use TCP port 80 but may also use TCP ports 3128, 8000, 8010, 8080, 8888, and 24326.

  MS13-091, Vulnerabilities in Microsoft Office Could Allow Remote Code Execution (2885093): These vulnerabilities have been assigned Common Vulnerabilities and Exposures (CVE) identifiers CVE-2013-0082, CVE-2013-1324, and CVE-2013-1325. These vulnerabilities can be exploited remotely with authentication and require user interaction. Successful exploitation of these vulnerabilities may allow remote code execution. The attack vector for exploitation of these vulnerabilities is through HTTP packets that typically use TCP port 80 but may also use TCP ports 3128, 8000, 8010, 8080, 8888, and 24326.

  The Cisco ASA 5500 Series Adaptive Security Appliance, Cisco Catalyst 6500 Series ASA Services Module (ASASM), and Cisco Firewall Services Module (FWSM) for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers provide protection for potential attempts to exploit these vulnerabilities. For configuration and use information see the Preventing ActiveX Exploits with Cisco Firewall Application Layer Protocol Inspection Cisco Security white paper.

  The Cisco ACE Application Control Engine Appliance and Module provide protection for potential attempts to exploit these vulnerabilities. For configuration and use information see the Preventing ActiveX Exploits with Cisco Application Control Engine Application Layer Protocol Inspection Cisco Security white paper.

Vulnerability Overview

• Information about vulnerable, unaffected, and fixed software is available in the Microsoft Security Bulletin Summary for November 2013, which is available at the following link: http://www.microsoft.com/technet/security/bulletin/ms13-nov

Mitigation Technique Overview

• The vulnerabilities that have a client software attack vector, can be exploited locally on the vulnerable device, require user interaction, can be exploited using web-based attacks (these include but are not limited to cross-site scripting, phishing, and web-based email threats) or email attachments are in the following list:

  • MS13-088
  • MS13-089
  • MS13-090
  • MS13-091
  • MS13-092
  • MS13-093
  • MS13-094
  • MS13-095

  These vulnerabilities are mitigated most successfully at the endpoint through software updates, user education, desktop administration best practices, and endpoint protection software such as Host Intrusion Prevention Systems (HIPS) or antivirus products.

  The vulnerabilities that have a network mitigation are in the following list. Cisco devices provide several countermeasures for these vulnerabilities. This section of the document provides an overview of these techniques.

  • MS13-089
  • MS13-090
  • MS13-091

  Effective exploit prevention can also be provided by the Cisco ASA 5500 Series Adaptive Security Appliance, Cisco Catalyst 6500 Series ASA Services Module (ASASM), and the Firewall Services Module (FWSM) for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers using application layer protocol inspection.

  This protection mechanism filters and drops packets that are attempting to exploit the vulnerabilities that have a network attack vector.

  Effective exploit prevention can also be provided by the Cisco ACE Application Control Engine Appliance and Module using application protocol inspection.

  Cisco ASA, Cisco ASASM, Cisco FWSM firewalls, and Cisco ACE Application Control Engine Appliance and Module can provide visibility through syslog messages and counter values displayed in the output from show commands.

  Effective use of Cisco Intrusion Prevention System (IPS) event actions provides visibility into and protection against attacks that attempt to exploit these vulnerabilities as discussed later in this document.

  Sourcefire signatures are also available for vulnerabilities discussed later in this document.

Risk Management

• Organizations are advised to follow their standard risk evaluation and mitigation processes to determine the potential impact of these vulnerabilities. Triage refers to sorting projects and prioritizing efforts that are most likely to be successful. Cisco has provided documents that can help organizations develop a risk-based triage capability for their information security teams. Risk Triage for Security Vulnerability Announcements and Risk Triage and Prototyping can help organizations develop repeatable security evaluation and response processes.

Device-Specific Mitigation and Identification

• Caution: The effectiveness of any mitigation technique depends on specific customer situations such as product mix, network topology, traffic behavior, and organizational mission. As with any configuration change, evaluate the impact of this configuration prior to applying the change.

  Specific information about mitigation and identification is available for these devices:

  • Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls
  • Cisco ACE
  • Cisco Intrusion Prevention System
  • Sourcefire Intrusion Prevention System

  Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls

  Mitigation: Application Layer Protocol Inspection

  Application layer protocol inspection is available beginning in software release 7.2(1) for the Cisco ASA 5500 Series Adaptive Security Appliance, software release 8.5 for the Cisco Catalyst 6500 Series ASA Services Module, and in software release 4.0(1) for the Cisco Firewall Services Module. This advanced security feature performs deep packet inspection of traffic that transits the firewall. Administrators may construct an inspection policy for applications that require special handling through the configuration of inspection class maps and inspection policy maps, which are applied by means of a global or interface service policy.

  Additional information about application inspection and the MPF is in the Configuring Application Inspection section of Book 2: Cisco ASA Series Firewall CLI Configuration Guide, 9.1.

  Caution: Application layer protocol inspection will decrease firewall performance. Administrators are advised to test performance impact in a lab environment before this feature is deployed in production environments.

  HTTP Application Inspection
  For MS13-089, MS13-090, and MS13-091 by using the HTTP inspection engine on the Cisco ASA 5500 Series Adaptive Security Appliances, Cisco 6500 Series ASA Services Modules, and the Cisco Firewall Services Module, administrators can configure regular expressions (regexes) for pattern matching and construct inspection class maps and inspection policy maps. These methods can help protect against specific vulnerabilities, such as the vulnerabilities described in this document, and other threats that may be associated with HTTP traffic. The following HTTP application inspection configuration uses the Cisco Modular Policy Framework (MPF) to create a policy for inspection of traffic on TCP ports 80, 3128, 8000, 8010, 8080, 8888, and 24326, which are the default ports for the Cisco IPS #WEBPORTS variable. The HTTP application inspection policy will drop connections where the HTTP response body contains any of the regexes that are configured to match the ActiveX control that is associated with these vulnerabilities.

  Caution: The configured regexes can match text strings at any location in the body of an HTML response. Care should be taken to ensure that legitimate business applications that use matching text strings without calling the ActiveX control are not affected. Additional information about regex syntax is in Creating a Regular Expression.

  Additional information about ActiveX exploits and mitigations that leverage Cisco firewall technologies is available in the Preventing ActiveX Exploits with Cisco Firewall Application Layer Protocol Inspection Cisco Security Intelligence Operations white paper.

  !
  !-- Configure regexes for the ActiveX Class ID 
  !-- "19916E01-B44E-4E31-94A4-4696DF46157B",
  !-- "C2C4F00A-720E-4389-AEB9-E9C4B0D93C6F", and 
  !-- "53001F3A-F5E1-4B90-9C9F-00E09B53C5F1" that
  !-- are associated with MS13-090
  !
  !-- Configure regexes that look for either of the
  !-- potentially malicious .wri and .wpd file extensions that
  !-- are typically used to exploit the vulnerabilities
  !-- associated with MS13-089 and MS13-091
  ! 
  regex CLSID_MS13-090_0 "19916[Ee]01[-][Bb]44[Ee][-]4[Ee]31[-]
                       94[Aa]4[-]4696[Dd][Ff]46157[Bb]"
  
  regex CLSID_MS13-090_1 "[Cc]2[Cc]4[Ff]00[Aa][-]720[Ee][-]4389[-]
                       [Aa][Ee][Bb]9[-][Ee]9[Cc]4[Bb]0[Dd]93[Cc]6[Ff]"
  
  regex CLSID_MS13-090_2 "53001[Ff]3[Aa][-][Ff]5[Ee]1[-]4[Bb]90[-]
                       9[Cc]9[Ff][-]00[Ee]09[Bb]53[Cc]5[Ff]1"
  
  regex MS13-089 ".+\x2e[Ww][Rr][Ii]"
  
  regex MS13-091 ".+\x2e[Ww][Pr][Dd]"
  ! 
  !-- Configure a regex class to match on the regular  
  !-- expressions that are configured above
  ! 
  class-map type regex match-any MS13-090_regex_class
   match regex CLSID_MS13-090_0
   match regex CLSID_MS13-090_1
   match regex CLSID_MS13-090_2
  
  class-map type regex match-any MS13-089_regex_class
   match regex MS13-089
  
  class-map type regex match-any MS13-091_regex_class
   match regex MS13-091
  !
  !-- Configure an object group for the default ports that 
  !-- are used by the Cisco IPS #WEBPORTS variable, which 
  !-- are TCP ports 80 (www), 3128, 8000, 8010, 8080, 8888, 
  !-- and 24326
  !
  object-group service WEBPORTS tcp
   port-object eq www 
   port-object eq 3128 
   port-object eq 8000 
   port-object eq 8010 
   port-object eq 8080 
   port-object eq 8888 
   port-object eq 24326 
  !
  !-- Configure an access list that uses the WEBPORTS object 
  !-- group, which will be used to match TCP packets that 
  !-- are destined to the #WEBPORTS variable that is used 
  !-- by a Cisco IPS device
  !
  access-list Webports_ACL extended permit tcp any any object-group WEBPORTS 
  !
  !-- Configure a class that uses the above-configured
  !-- access list to match TCP packets that are destined
  !-- to the ports that are used by the Cisco IPS #WEBPORTS
  !-- variable
  !
  class-map Webports_Class
   match access-list Webports_ACL
  !
  !-- Configure an HTTP application inspection policy that  
  !-- identifies, drops, and logs connections that contain   
  !-- the regexes that are configured above
  ! 
  policy-map type inspect http MS_Nov_2013_policy
   parameters
  !
  !-- "body-match-maximum" indicates the maximum number of 
  !-- characters in the body of an HTTP message that
  !-- should be searched in a body match. The default value is
  !-- 200 bytes. A large number such as shown here may have an
  !-- impact on system performance.  Administrators are advised
  !-- to test performance impact in a lab environment before 
  !-- this command is deployed in production environments
  !
   body-match-maximum 1380
   match response body regex class MS13-089_regex_class
    drop-connection log
   match response body regex class MS13-090_regex_class
    drop-connection log
   match response body regex class MS13-091_regex_class    
    drop-connection log  
  !
  !-- Add the above-configured "Webports_Class" that matches 
  !-- TCP packets that are destined to the default ports  
  !-- that are used by the Cisco IPS #WEBPORTS variable to  
  !-- the default policy "global_policy" and use it to 
  !-- inspect HTTP traffic that transits the firewall
  ! 
  policy-map global_policy
   class Webports_Class
    inspect http MS_Nov_2013_policy 
  !
  !-- By default, the policy "global_policy" is applied 
  !-- globally, which results in the inspection of 
  !-- traffic that enters the firewall from all interfaces 
  !
  service-policy global_policy global

  For additional information about the configuration and use of object groups, reference the Configuring Objects and ACLs section of Book 1: Cisco ASA Series General Operations CLI Configuration Guide, 9.1.

  Additional information about HTTP application inspection and the MPF is in the Configuring Application Inspection section of Book 2: Cisco ASA Series Firewall CLI Configuration Guide, 9.1.

  For information on using the Cisco Firewall command line interface to gauge the effectiveness of application inspection, please refer to the Cisco Security Intelligence Operations white paper Identification of Security Exploits with Cisco ASA, Cisco ASASM, and Cisco FWSM Firewalls.

  Cisco ACE

  Mitigation: Application Protocol Inspection

  Application protocol inspection is available for the Cisco ACE Application Control Engine Appliance and Module. This advanced security feature performs deep packet inspection of traffic that transits the Cisco ACE device. Administrators can construct an inspection policy for applications that require special handling through the configuration of inspection class maps and inspection policy maps, which are applied via a global or interface service policy.

  Additional information about application protocol inspection is in the Configuring Application Protocol Inspection section of the Security Guide vA5(1.0), Cisco ACE Application Control Engine.

  HTTP Deep Packet Inspection

  To conduct HTTP deep packet inspection For MS13-089, MS13-090, and MS13-091, administrators can configure regular expressions (regexes) for pattern matching and construct inspection class maps and inspection policy maps. These methods can help protect against specific vulnerabilities, such as the one described in this document, and other threats that may be associated with HTTP traffic. The following HTTP application protocol inspection configuration inspects traffic on TCP ports 80, 3128, 8000, 8010, 8080, 8888, and 24326, which are the default ports for the Cisco IPS #WEBPORTS variable. The HTTP application protocol inspection policy will drop connections where the HTTP content contains any of the regexes that are configured to match the ActiveX control that is associated with these vulnerabilities.

  Caution: The configured regexes can match text strings at any location in the content of an HTML packet. Care should be taken to ensure that legitimate business applications that use matching text strings without calling the ActiveX control are not affected.

  Additional information about ActiveX exploits and mitigations that leverage the Cisco ACE Application Control Engine Appliance and Module is available in the Preventing ActiveX Exploits with Cisco Application Control Engine Application Layer Protocol Inspection Cisco Security Intelligence Operations white paper.

  ! 
  !-- Configure an HTTP application inspection class that
  !-- looks for HTTP packets that contain the regexes for the
  !-- ActiveX Class IDs "19916E01-B44E-4E31-94A4-4696DF46157B",
  !-- "C2C4F00A-720E-4389-AEB9-E9C4B0D93C6F", and  
  !-- "53001F3A-F5E1-4B90-9C9F-00E09B53C5F1" that are
  !-- associated with MS13-090
  ! 
  !-- Configure regexes that look for either of the
  !-- potentially malicious .wri and .wpd file extensions that
  !-- are typically used to exploit the vulnerabilities
  !-- associated with MS13-089 and MS13-091
  ! 
  class-map type http inspect match-any MS13-090_class
    match content ".*19916[Ee]01[-][Bb]44[Ee][-]4[Ee]31[-]
                   94[Aa]4[-]4696[Dd][Ff]46157[Bb].*"
  
    match content ".*[Cc]2[Cc]4[Ff]00[Aa][-]720[Ee][-]4389[-]
                   [Aa][Ee][Bb]9[-][Ee]9[Cc]4[Bb]0[Dd]93[Cc]6[Ff].*"
  
    match content ".*53001[Ff]3[Aa][-][Ff]5[Ee]1[-]4[Bb]90[-]
                   9[Cc]9[Ff][-]00[Ee]09[Bb]53[Cc]5[Ff]1.*"
  
  class-map type http inspect match-any MS13-089_class
    2 match content ".*.+\x2e[Ww][Rr][Ii].*"                     
  
  class-map type http inspect match-any MS13-091_class
    2 match content ".+\x2e[Ww][Pp][Dd].*"                     
  !
  !-- Configure an HTTP application inspection policy that
  !-- identifies, resets, and logs connections that contain
  !-- the regexes that are configured above
  !
  policy-map type inspect http all-match MS_Nov_2013
    class MS13-089_class
      reset log
    class MS13-090_class
      reset log 
    class MS13-091_class
      reset log 
  !
  !-- Configure an access list that matches TCP packets
  !-- that are destined to the #WEBPORTS variable that is
  !-- used by a Cisco IPS device
  !
  access-list WEBPORTS line 8 extended permit tcp any any eq www 
  access-list WEBPORTS line 16 extended permit tcp any any eq 3128 
  access-list WEBPORTS line 24 extended permit tcp any any eq 8000 
  access-list WEBPORTS line 32 extended permit tcp any any eq 8010 
  access-list WEBPORTS line 40 extended permit tcp any any eq 8080 
  access-list WEBPORTS line 48 extended permit tcp any any eq 8888 
  access-list WEBPORTS line 56 extended permit tcp any any eq 24326 
  !
  !-- Configure a Layer 4 class that uses the above-configured
  !-- access list to match TCP packets that are destined
  !-- to the ports that are used by the Cisco IPS #WEBPORTS
  !-- variable
  !
  class-map match-all L4_http_class
    match access-list WEBPORTS
  !
  !-- Configure a Layer 4 policy that applies the HTTP application
  !-- inspection policy configured above to TCP packets that
  !-- are destined to the ports that are used by the Cisco IPS
  !-- #WEBPORTS variable
  !
  policy-map multi-match L4_MS_Nov_2013
    class L4_http_class
      inspect http policy MS_Nov_2013  
  !
  !-- Apply the configuration globally across all interfaces,
  !-- which results in the inspection of all traffic that enters
  !-- the ACE
  !
  service-policy input L4_MS_Nov_2013

  For information on using the Cisco Firewall command line interface to gauge the effectiveness of application inspection, please refer to the Cisco Security Intelligence Operations white paper Identification of Malicious Traffic Using Cisco ACE.

  Cisco Intrusion Prevention System

  Mitigation: Cisco IPS Signature Event Actions

  Administrators can use the Cisco IPS appliances and services modules to provide threat detection and help prevent attempts to exploit several of the vulnerabilities described in this document. The following table provides an overview of CVE identifiers and the respective Cisco IPS signatures that will trigger events on potential attempts to exploit these vulnerabilities.

  CVE ID	Signature Release	Signature ID	Signature Name	Enabled	Severity	Fidelity*
  CVE-2013-3871	S748	2897/0	Potentially Malicious Web Page	No	Medium	70
  CVE-2013-3910	S753	3090/0	Microsoft Internet Explorer Use After Free Vulnerability	Yes	High	90
  CVE-2013-3911	S753	3093/0	Microsoft Internet Explorer Use After Free Vulnerability	Yes	High	85
  CVE-2013-3912	S753	3148/0	Microsoft Internet Explorer Memory Corruption	Yes	High	85
  CVE-2013-3914	S753	3092/0	Microsoft Internet Explorer Heap Corruption	Yes	High	85
  CVE-2013-3915	S753	3149/0	Microsoft Internet Explorer Memory Corruption	Yes	High	85
  CVE-2013-3916	S753	3098/0	Microsoft Internet Explorer Use After Free Vulnerability	Yes	High	85
  CVE-2013-3917	S753	3097/0	Microsoft Windows Internet Explorer Memory Corruption	Yes	High	85
  CVE-2013-3940	S753	3074/0	Windows Graphics Device Interface Remote Code Execution	Yes	High	85
  CVE-2013-3918	S753	3080/0	Microsoft Windows InformationCardSigninHelper Vulnerability	Yes	High	85
  CVE-2013-1324	S753	3147/0	Microsoft Word Stack Buffer Overwrite Vulnerability	Yes	High	85
  CVE-2013-1325	S753	2776/0	Microsoft Office Word Wordperfect File Processing Heap Overflow Vulnerability	Yes	High	85

  * Fidelity is also referred to as Signature Fidelity Rating (SFR) and is the relative measure of the accuracy of the signature (predefined). The value ranges from 0 through 100 and is set by Cisco Systems, Inc.

  Administrators can configure Cisco IPS sensors to perform an event action when an attack is detected. The configured event action performs preventive or deterrent controls to help protect against an attack that is attempting to exploit the vulnerabilities listed in the preceding table.

  Cisco IPS sensors are most effective when deployed in inline protection mode combined with the use of an event action. Automatic Threat Prevention for Cisco IPS 7.x and 6.x sensors that are deployed in inline protection mode provides threat prevention against an attack that is attempting to exploit the vulnerability that is described in this document. Threat prevention is achieved through a default override that performs an event action for triggered signatures with a riskRatingValue greater than 90.

  For additional information about the risk rating and threat rating calculation, reference Risk Rating and Threat Rating: Simplify IPS Policy Management.

  For information on using Cisco Security Manager to monitor alerts from Cisco IPS, please refer to Identification of Malicious Traffic Using Cisco Security Manager.

  Sourcefire Signature Information

  Sourcefire Signature Identification

  The following Sourcefire Snort signatures are available for the Microsoft November 2013 Security Update.

  Microsoft Advisory	Sourcefire GID:SID
  MS13-088	1:28490
  MS13-088	1:28491
  MS13-088	1:28492
  MS13-088	1:28494
  MS13-088	1:28495
  MS13-088	1:28496
  MS13-088	1:28504
  MS13-088	1:28522
  MS13-088	1:28523
  MS13-088	1:28524
  MS13-089	1:28509
  MS13-089	1:28510
  MS13-089	1:28511
  MS13-089	1:28512
  MS13-089	1:28513
  MS13-089	1:28514
  MS13-089	1:28515
  MS13-089	1:28516
  MS13-089	1:28517
  MS13-089	1:28518
  MS13-089	1:28519
  MS13-089	1:28520
  MS13-089	1:28521
  MS13-090	1:28493
  MS13-090	1:28505
  MS13-090	1:28506
  MS13-091	1:28498
  MS13-091	1:28499
  MS13-091	1:28502
  MS13-091	1:28503

Additional Information

• THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.

Revision History

• Version	Description	Section	Date
  1	Initial Release		2013-November-12 19:07 GMT

  Show Less

Cisco Security Procedures

• Complete information on reporting security vulnerabilities in Cisco products, obtaining assistance with security incidents, and registering to receive security information from Cisco, is available on Cisco's worldwide website at https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html. This includes instructions for press inquiries regarding Cisco security notices. All Cisco security advisories are available at http://www.cisco.com/go/psirt.

Related Information

• • Cisco Applied Mitigation Bulletins
  • Cisco Security
  • Cisco Security IntelliShield Alert Manager Service
  • Cisco Firewall Products - Home Page on Cisco.com
  • Cisco Catalyst 6500 Series ASA Services Module
  • Cisco ACE Application Control Engine Module Documentation
  • Unicast Reverse Path Forwarding Enhancements for the Internet Service Provider
  • Cisco Intrusion Prevention System
  • Cisco IPS Signature Downloads
  • Cisco IPS Signature Search Page
  • Cisco Security Manager
  • Common Vulnerabilities and Exposures (CVE)
  • Subscribe to Cisco Applied Mitigation Bulletins

Affected Products

• The security vulnerability applies to the following combinations of products.
  
  

  Primary Products
  Microsoft, Inc.	Internet Explorer	6.0 (Base, SP1, SP2) | 7.0 (Base) | 8.0 (Base) | 9.0 (Base) | 10.0 (Base) | 11.0 (Base)
  	Office	2003 (SP3) | 2007 (SP3) | 2010 (SP1) | 2013 (32-bit editions, 64-bit editions) | 2013 RT (Base)
  	Outlook	2007 (SP3) | 2010 (SP1, SP2) | 2013 RT (Base)
  	Windows 7	for 32-bit systems (Base, SP1) | for x64-based systems (Base, SP1)
  	Windows 8	for 32-bit systems (Base) | for x64-based systems (Base)
  	Windows 8.1	for 32-bit Systems (Base) | for x64-based Systems (Base)
  	Windows RT	Original Release (Base) | 8.1 (Base)
  	Windows Server 2003	Datacenter Edition (Base, SP1, SP2) | Datacenter Edition, 64-bit (Itanium) (Base, SP1, SP2) | Datacenter Edition x64 (AMD/EM64T) (Base, SP1, SP2) | Enterprise Edition (Base, SP1, SP2) | Enterprise Edition, 64-bit (Itanium) (Base, SP1, SP2) | Enterprise Edition x64 (AMD/EM64T) (Base, SP1, SP2) | Standard Edition (Base, SP1, SP2) | Standard Edition, 64-bit (Itanium) (Base, SP1, SP2) | Standard Edition x64 (AMD/EM64T) (Base, SP1, SP2) | Web Edition (Base, SP1, SP2)
  	Windows Server 2008	Datacenter Edition (Base, SP1, SP2) | Datacenter Edition, 64-bit (Base, SP1, SP2) | Itanium-Based Systems Edition (Base, SP1, SP2) | Enterprise Edition (Base, SP1, SP2) | Enterprise Edition, 64-bit (Base, SP1, SP2) | Essential Business Server Standard (Base, SP1, SP2) | Essential Business Server Premium (Base, SP1, SP2) | Essential Business Server Premium, 64-bit (Base, SP1, SP2) | Standard Edition (Base, SP1, SP2) | Standard Edition, 64-bit (Base, SP1, SP2) | Web Server (Base, SP1, SP2) | Web Server, 64-bit (Base, SP1, SP2)
  	Windows Server 2008 R2	x64-Based Systems Edition (Base, SP1) | Itanium-Based Systems Edition (Base, SP1)
  	Windows Server 2012	Original Release (Base)
  	Windows Server 2012 R2	Original Release (Base)
  	Windows Vista	Home Basic (Base, SP1, SP2) | Home Premium (Base, SP1, SP2) | Business (Base, SP1, SP2) | Enterprise (Base, SP1, SP2) | Ultimate (Base, SP1, SP2) | Home Basic x64 Edition (Base, SP1, SP2) | Home Premium x64 Edition (Base, SP1, SP2) | Business x64 Edition (Base, SP1, SP2) | Enterprise x64 Edition (Base, SP1, SP2) | Ultimate x64 Edition (Base, SP1, SP2)
  	Word	2003 (SP3) | 2007 (SP3) | 2010 (SP1) | 2013 (Base)

  
  
  

  Associated Products
  Cisco	Cisco Broadband Troubleshooter	Original Release (Base) | 3.1 (Base) | 3.2 (Base)
  	Cisco Building Broadband Service Manager (BBSM)	Original Release (Base) | 2.5 (.1) | 3.0 (Base) | 4.0 (Base, .1) | 4.2 (Base) | 4.3 (Base) | 4.4 (Base) | 4.5 (Base) | 5.0 (Base) | 5.1 (Base) | 5.2 (Base)
  	Cisco CNS Network Registrar	2.5 (Base) | 3.0 (Base) | 3.5 (Base, .1) | 5.0 (Base) | 5.5 (Base, .13) | 6.0 (.5, .5.2, .5.3, .5.4) | 6.1 (Base, .1, .1.1, .1.2, .1.3, .1.4)
  	Cisco Collaboration Server Dynamic Content Adapter (DCA)	Original Release (Base) | 1.0 (Base) | 2.0 (Base, (1)_SR2)
  	Cisco Computer Telephony Integration (CTI) Option	4.7 ((0)_SR1, (0)_SR2, (0)_SR3, (0)_SR4) | 5.1 ((0)_SR1, (0)_SR2, (0)_SR3) | 6.0 ((0)_SR1, (0)_SR2, (0)_SR3, (0)_SR4, (0)_SR5) | 7.0 ((0)_SR1, (0)_SR2) | 7.1 ((2), (3), (4), (5))
  	Cisco Conference Connection	1.1 ((3), (3)spA) | 1.2 (Base, (1), (2), (2)SR1, (2)SR2)
  	Cisco E-mail Manager	Original Release (Base) | 4.0 (Base, .5i, .6) | 5.0 (Base, (0)_SR1, (0)_SR3, (0)_SR4, (0)_SR5, (0)_SR6, (0)_SR7)
  	Cisco Emergency Responder	1.1 (Base, (3), (4)) | 1.2 (Base, (1), (1)SR1, (2), (2)sr1, (3)a, (3)SR1, (3a)SR2) | 1.3 (Base, (1a), (2))
  	Cisco Intelligent Contact Manager (ICM)	Original Release (Base) | 4.6 ((2)_SR1, (2)_SR2, (2)_SR3, (2)_SR4, (2)_SR5, (2)_SR6) | 5.0 ((0), (0)_SR2, (0)_SR3, (0)_SR4, (0)_SR5, (0)_SR7, (0)_SR8, (0)_SR9, (0)_SR10, (0)_SR11, (0)_SR12, (0)_SR13) | 6.0 ((0)_SR1, (0)_SR2, (0)_SR3, (0)_SR4, (0)_SR5, (0)_SR6, (0)_SR7, (0)_SR8, (0)_SR9, (0)_SR10) | 7.0 ((0)_SR1, (0)_SR2, (0)_SR3, (0)_SR4) | 7.1 ((2), (3), (4), (5))
  	Cisco Unified Contact Center	Enterprise Edition (Base, 4.6.2, 5.0, 6.0, 7.0, 7.1, 7.1.1, 7.1.3) | Express Edition (Base, 2.0, 2.0.2, 2.1, 2.1.1a, 2.1.2, 2.1.3, 2.2, 2.2.1, 2.2.2, 2.2.3b, 2.2.3b_spE, 3.0, 3.0.2, 3.0.3a_spA, 3.0.3a_spB, 3.0.3a_spC, 3.0.3a_spD, 3.1, 3.1(1)_SR1, 3.1(1)_SR2, 3.1(2)_SR1, 3.1(2)_SR2, 3.1(2)_SR3, 3.1(2)_SR4, 3.1(3)_SR2, 3.1(3)_SR3, 3.1(3)_SR4, 3.1(3)_SR5, 3.5, 3.5.1, 3.5(1)_SR1, 3.5(2)_SR1, 3.5(3), 3.5(3)_SR1, 3.5(3)_SR2, 3.5(3)_SR3, 3.5(4)_SR1, 3.5(4)_SR2, 4.0, 4.0(1)_SR1, 4.0(4)_SR1, 4.0(5)_SR1, 4.1, 4.1(1)_SR1, 4.5, 4.5(2)_SR1, 4.5(2)_SR2, 5.0(1)_SR1) | Hosted Edition (Base, 4.6.2, 5.0, 6.0, 7.0, 7.1, 7.1.1, 7.1.3)
  	Cisco Unified IP IVR	2.0 (.2) | 2.1 (.1a, .2, .3) | 2.2 ((5), .1, .2, .3b, .3b_spE, .5, .4) | 3.0 (.1_spB, .2, .3a_spA, .3a_spB, .3a_spC, .3a_spD) | 3.1 ((1)_SR2, (2)_SR1, (2)_SR2, (2)_SR3, (3)_SR1, (3)_SR2, (3)_SR3, (3)_SR4, (3)_SR5) | 3.5 ((1)_SR1, (1)_SR2, (1)_SR3, (2)_SR1, (3)_SR1, (3)_SR2, (3)_SR3, (4)_SR1, (4)_SR2, .1, .3) | 4.0 ((1)_SR1, (4)_SR1) | 4.1 ((1)_SR1) | 4.5 ((2)_SR1, (2)_SR2) | 5.0 ((1)_SR1)
  	Cisco IP Interoperability and Collaboration System (IPICS)	1.0 ((1.1))
  	Cisco IP Queue Manager	2.2 (Base)
  	Cisco IP/VC 3540 Application Server Module	3.2 (.0.1, .138) | 3.5 (.0.8)
  	Cisco IP/VC 3540 Rate Matching Module	3.0 (.9)
  	Cisco Media Blender	Original Release (Base) | 3.0 (Base) | 4.0 (Base) | 5.0 (Base, (0)_SR1, (0)_SR2)
  	Cisco Networking Services for Active Directory	Original Release (Base)
  	Cisco Outbound Option	Original Release (Base)
  	Cisco Personal Assistant	1.0 (Base, (1)) | 1.1 (Base) | 1.3 (Base, .1, .2, .3, .4) | 1.4 (Base, .2, .3, .4, .5, .6)
  	Cisco Remote Monitoring Suite Option	1.0 (Base) | 2.0 (Base, (0)_SR1)
  	Cisco Secure Access Control Server (ACS) for Windows	2.6 (Base) | 2.6.3.2 (Base) | 2.6.4 (Base) | 2.6.4.4 (Base) | 3.0 (Base) | 3.0.1 (Base) | 3.0.1.40 (Base) | 3.0.2 (Base) | 3.0.3 (Base) | 3.0.3.6 (Base) | 3.0.4 (Base) | 3.1.1 (Base) | 3.1.1.27 (Base) | 3.1.2 (Base) | 3.2 (Base) | 3.2.1 (Base) | 3.2.3 (Base) | 3.3.1 (Base) | 3.3.2.2 (Base) | 3.3.1.16 (Base) | 3.3.3.11 (Base) | 4.0 (Base) | 4.0.1 (Base) | 4.0.1.27 (Base) | 4.1.1.23 (Base)
  	Cisco Secure Access Control Server Solution Engine (ACSE)	3.1 (Base, .1) | 3.2 (Base, .1.20, .2.5, .3) | 3.3 (Base, .1, .1.16, .2.2, .3, .4, .4.12) | 4.0 (Base, .1, .1.42, .1.44, .1.49) | 4.1 (Base, .1.23, .1.23.3, .3, .3.12)
  	Cisco Secure User Registration Tool (URT)	Original Release (Base) | 1.2 (Base, .1) | 2.0 (Base, .7, .8) | 2.5 (Base, .1, .2, .3, .4, .5)
  	Cisco SN 5420 Storage Router	1.1 (Base, .3, .4, .5, .7, .8) | 2.1 (.1, .2)
  	Cisco SN 5428-2 Storage Router	3.2 (.1, .2) | 3.3 (.1, .2) | 3.4 (.1) | 3.5 (Base, .1, .2, .3, .4)
  	Cisco Trailhead	Original Release (Base) | 4.0 (Base)
  	Cisco Unified Communications Manager	Original Release (Base) | 1.0 (Base) | 2.0 (Base) | 3.0 (Base) | 3.0.3(a) (Base) | 3.1 (Base, .1, .2, .3a) | 3.1(1) (Base) | 3.1(2) (Base) | 3.1(2)SR3 (Base) | 3.1(3) (Base) | 3.1(3)SR2 (Base) | 3.1(3)SR4 (Base) | 3.2 (Base) | 3.2(3)SR3 (Base) | 3.3 (Base) | 3.3(2)SPc (Base) | 3.3(3) (Base) | 3.3(3)ES61 (Base) | 3.3(3)SR3 (Base) | 3.3(3)SR4a (Base) | 3.3(3a) (Base) | 3.3(4) (Base) | 3.3(4)ES25 (Base) | 3.3(4)SR2 (Base) | 3.3(4c) (Base) | 3.3(5) (Base) | 3.3(5)ES24 (Base) | 3.3(5)SR1 (Base) | 3.3(5)SR1a (Base) | 3.3(5)SR2 (Base) | 3.3(5)SR2a (Base) | 3.3(5)SR3 (Base) | 3.3(59) (Base) | 3.3(61) (Base) | 3.3(63) (Base) | 3.3(64) (Base) | 3.3(65) (Base) | 3.3(66) (Base) | 3.3(67.5) (Base) | 3.3(68.1) (Base) | 3.3(71.0) (Base) | 3.3(74.0) (Base) | 3.3(78) (Base) | 3.3(76) (Base) | 4.0 (.1, .2) | 4.0(2a)ES40 (Base) | 4.0(2a)ES56 (Base) | 4.0(2a)SR2b (Base) | 4.0(2a)SR2c (Base) | 4.1 (Base) | 4.1(2) (Base) | 4.1(2)ES33 (Base) | 4.1(2)ES50 (Base) | 4.1(2)SR1 (Base) | 4.1(3) (Base) | 4.1(3)ES (Base) | 4.1(3)ES07 (Base) | 4.1(3)ES24 (Base) | 4.1(3)SR (Base) | 4.1(3)SR1 (Base) | 4.1(3)SR2 (Base) | 4.1(3)SR3 (Base) | 4.1(3)SR3b (Base) | 4.1(3)SR3c (Base) | 4.1(3)SR4 (Base) | 4.1(3)SR4b (Base) | 4.1(3)SR4d (Base) | 4.1(3)SR5 (Base) | 4.1(4) (Base) | 4.1(9) (Base) | 4.1(17) (Base) | 4.1(19) (Base) | 4.1(22) (Base) | 4.1(23) (Base) | 4.1(25) (Base) | 4.1(26) (Base) | 4.1(27.7) (Base) | 4.1(28.2) (Base) | 4.1(30.4) (Base) | 4.1(36) (Base) | 4.1(39) (Base) | 4.2(1) (Base) | 4.2(1)SR1b (Base) | 4.2(1.02) (Base) | 4.2(1.05.3) (Base) | 4.2(1.06) (Base) | 4.2(1.07) (Base) | 4.2(3) (Base) | 4.2(3)SR1 (Base) | 4.2(3)SR2 (Base) | 4.2(3.08) (Base) | 4.2(3.2.3) (Base) | 4.2(3.3) (Base) | 4.2(3.13) (Base) | 4.3(1) (Base) | 4.3(1)SR (Base) | 4.3(1.57) (Base)
  	Cisco Unified Customer Voice Portal (CVP)	3.0 ((0), (0)SR1, (0)SR2) | 3.1 ((0), (0)SR1, (0)SR2) | 4.0 ((0), (1), (1)SR1, (2))
  	Cisco Unified MeetingPlace	4.3 (Base) | 5.3 (Base) | 5.2 (Base) | 5.4 (Base) | 6.0 (Base)
  	Cisco Unified MeetingPlace Express	1.1 (Base) | 1.2 (Base) | 2.0 (Base)
  	Cisco Unity	Original Release (Base) | 2.0 (Base) | 2.1 (Base) | 2.2 (Base) | 2.3 (Base) | 2.4 (Base) | 2.46 (Base) | 3.0 (Base, .1) | 3.1 (Base, .2, .3, .5, .6) | 3.2 (Base) | 3.3 (Base) | 4.0 (Base, .1, .2, .3, .3b, .4, .5) | 4.1 (Base, .1) | 4.2 (Base, .1, .1 ES27) | 5.0 ((1)) | 7.0 ((2))
  	Cisco Unity Express	1.0.2 (Base) | 1.1.1 (Base) | 1.1.2 (Base) | 2.0.1 (Base) | 2.0.2 (Base) | 2.1.1 (Base) | 2.1.2 (Base) | 2.1.3 (Base) | 2.2.0 (Base) | 2.2.1 (Base) | 2.2.2 (Base) | 2.3.0 (Base) | 2.3.1 (Base)
  	Cisco Wireless Control System (WCS) Software	1.0 (Base) | 2.0 (Base, 44.14, 44.24) | 2.2 (.0, .111.0) | 3.0 (Base, .101.0, .105.0) | 3.1 (Base, .20.0, .33.0, .35.0) | 3.2 (Base, .23.0, .25.0, .40.0, .51.0, .64.0) | 4.0 (Base, .1.0, .43.0, .66.0, .81.0, .87.0, .96.0, .97.0) | 4.1 (Base, .83.0)
  	CiscoWorks IP Telephony Environment Monitor (ITEM)	1.3 (Base) | 1.4 (Base) | 2.0 (Base)
  	CiscoWorks LAN Management Solution (LMS)	1.3 (Base) | 2.2 (Base) | 2.5 (Base) | 2.6 (Base)
  	CiscoWorks QoS Policy Manager (QPM)	2.0 (Base, .1, .2, .3) | 2.1 (.2) | 3.0 (Base, .1) | 3.1 (Base) | 3.2 (Base, .1, .2, .3)
  	CiscoWorks Routed WAN Management Solution (RWAN)	1.0 (Base) | 1.1 (Base) | 1.2 (Base) | 1.3 (Base, .1)
  	CiscoWorks Small Network Management Solution (SNMS)	1.0 (Base) | 1.5 (Base)
  	CiscoWorks VPN/Security Management Solution (VMS)	1.0 (Base) | 2.0 (Base) | 2.1 (Base) | 2.2 (Base) | 2.3 (Base)
  	Cisco Collaboration Server	3.0 (Base) | 3.01 (Base) | 3.02 (Base) | 4.0 (Base) | 5.0 (Base)
  	Cisco DOCSIS CPE Configurator	1.0 (Base) | 1.1 (Base) | 2.0 (Base)
  	Cisco Unified IP Interactive Voice Response (IVR)	2.0 (Base) | 2.1 (Base)
  	Cisco Service Control Engine (SCE)	3.0 (Base) | 3.1 (Base)
  	Cisco Transport Manager	Original Release (Base) | 2.0 (Base) | 2.1 (Base) | 2.2 (Base, .1) | 3.0 (Base, .1, .2) | 3.1 (Base) | 3.2 (Base) | 4.0 (Base) | 4.1 (Base, .4, .6, .6.6.1) | 4.6 (Base) | 4.7 (Base) | 5.0 (Base, .0.867.2, .1.873.2, .2, .2.92.1, .2.99.1, .2.105.1, .2.110.1) | 6.0 (Base, .0.405.1, .0.407.1, .0.412.1) | 7.0 (Base, .0.370.1, .0.372.1, .0.377.1, .0.389.1, .0.400.1, .395.1) | 7.2 (Base, .0.199.1)
  Microsoft, Inc.	Office	2010 (SP2) | 2013 | 2013 RT
  	Windows 7	for 32-bit systems | for x64-based systems
  	Windows 8	for 32-bit systems | for x64-based systems
  	Windows 8.1	for 32-bit Systems | for x64-based Systems
  	Windows RT	Original Release | 8.1
  	Windows Server 2003	Datacenter Edition | Datacenter Edition, 64-bit (Itanium) | Datacenter Edition x64 (AMD/EM64T) | Enterprise Edition | Enterprise Edition, 64-bit (Itanium) | Enterprise Edition x64 (AMD/EM64T) | Standard Edition | Standard Edition, 64-bit (Itanium) | Standard Edition x64 (AMD/EM64T) | Web Edition
  	Windows Server 2008	Datacenter Edition | Datacenter Edition, 64-bit | Itanium-Based Systems Edition | Enterprise Edition | Enterprise Edition, 64-bit | Essential Business Server Standard | Essential Business Server Premium | Essential Business Server Premium, 64-bit | Standard Edition | Standard Edition, 64-bit | Web Server | Web Server, 64-bit
  	Windows Server 2008 R2	x64-Based Systems Edition | Itanium-Based Systems Edition
  	Windows Server 2012	Original Release
  	Windows Server 2012 R2	Original Release
  	Windows Vista	Home Basic | Home Premium | Business | Enterprise | Ultimate | Home Basic x64 Edition | Home Premium x64 Edition | Business x64 Edition | Enterprise x64 Edition | Ultimate x64 Edition