This document shows how to configure Virtual Private Network (VPN) Multiprotocol Label Switching (MPLS) over ATM with Cisco 7500 routers as Label Edge Routers (LERs) and LightStream 1010 switches as Label Switch Routers (LSRs). Two ethernet-connected routers, each on a remote customer site, are part of a VPN. In this document, we look at the end-to-end device configurations and helpful show commands.
There are no specific requirements for this document.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
In this section, you are presented with the information to configure the features described in this document.
This document uses this network setup:
The current setup contains these elements in VPN terminology:
CE = Customer Edge Router
PE = Provider Edge Router
P=Provider Router
The current setup contains these elements in MPLS terminology:
LER = Label Edge Router
LSR = Label Switch Router
TDP/LDP = Tag Distribution Protocol/Label Distribution Protocol
This document uses these configurations:
PE1 and PE2 are the LERs in our ATM network.
P1 and P2 are the LSRs.
CE1 and CE2 are Customer Edge Routers that are unaware and do not carry out VPN or MPLS.
CE1 and CE2 are Ethernet connected to PE1 and PE2 respectively, and carry out Routing Information Protocol (RIP).
PE1, PE2, P1 and P2 do Open Shortest Path First (OSPF) and are all in Area 0. OSPF is the Interior Gateway Protocol (IGP) used in the ATM network. Tag-switching is used on the ATM interfaces on all four ATM devices. Tag Distribution Protocol (TDP) assigns Tags to the OSPF routes.
PE1 and PE2 are Multiprotocol-Border Gateway Protocol (MP-BGP) peers.
RIP routes are redistributed into MP-BGP. MP-BGP routes redistributed into RIP on PE1 and PE2 routers.
The setup maintains separate VRF routing tables in the PE1 and PE2 routers.
The name of the VPN used in this example is NEW.
CE1 |
---|
! version 12.1 service timestamps debug datetime msec service timestamps log datetime msec ! boot system flashow c4500-js-mz.121-5 ! ip subnet-zero ! interface Loopback0 ip address 10.1.1.1 255.255.255.0 ! interface Loopback1 ip address 10.2.2.2 255.255.255.0 ! interface Loopback2 ip address 10.3.3.3 255.255.255.0 ! interface Ethernet0 ip address 100.1.1.2 255.255.255.0 media-type 10BaseT ! router rip version 2 network 10.0.0.0 network 100.0.0.0 no auto-summary ! ip classless ! |
PE1 |
---|
! version 12.1 service timestamps debug uptime service timestamps log uptime ! boot system flashow slot1:rsp-jsv-mz.121-5a.bin ! ip subnet-zero ! ip vrf NEW rd 200:1 route-target export 200:1 route-target import 200:1 ip cef distributed ! interface Loopback0 ip address 1.1.1.1 255.255.255.255 ! interface ATM2/0/0 mtu 1500 no ip address ! interface ATM2/0/0.10 tag-switching ip unnumbered Loopback0 tag-switching ip ! interface Ethernet2/1/0 ip vrf forwarding NEW ip address 100.1.1.1 255.255.255.0 ! router ospf 100 no log-adjacency-changes network 1.0.0.0 0.255.255.255 area 0 network 100.1.1.0 0.0.0.255 area 0 ! router rip version 2 network 100.0.0.0 no auto-summary ! address-family ipv4 vrf NEW version 2 redistribute bgp 200 metric 0 network 100.0.0.0 no auto-summary exit-address-family ! router bgp 200 bgp log-neighbor-changes neighbor 2.2.2.2 remote-as 200 neighbor 2.2.2.2 update-source Loopback0 no auto-summary ! address-family ipv4 vrf NEW redistribute rip no auto-summary no synchronization exit-address-family ! address-family vpnv4 neighbor 2.2.2.2 activate neighbor 2.2.2.2 send-community extended no auto-summary exit-address-family ! ip classless ! |
P1 |
---|
! service timestamps debug uptime service timestamps log uptime ! ip subnet-zero ! interface Loopback0 ip address 4.4.4.4 255.255.255.255 no ip directed-broadcast ! interface ATM12/0/0 ip unnumbered Loopback0 no ip directed-broadcast tag-switching ip ! interface ATM12/0/1 ip unnumbered Loopback0 no ip directed-broadcast tag-switching ip ! router ospf 100 network 4.0.0.0 0.255.255.255 area 0 ! ip classless ! |
P2 |
---|
! service timestamps debug uptime service timestamps log uptime ! ip subnet-zero ! interface Loopback0 ip address 3.3.3.3 255.255.255.255 no ip directed-broadcast ! interface ATM0/1/1 ip unnumbered Loopback0 no ip directed-broadcast tag-switching ip ! interface ATM0/1/3 ip unnumbered Loopback0 no ip directed-broadcast tag-switching ip ! router ospf 100 network 3.0.0.0 0.255.255.255 area 0 ! ip classless ! |
PE2 |
---|
! version 12.1 service timestamps debug datetime msec service timestamps log datetime msec ! boot system flashow slot0:rsp-jsv-mz.121-5a ! ip subnet-zero ! ip vrf NEW rd 200:1 route-target export 200:1 route-target import 200:1 ip cef distributed ! interface Loopback0 ip address 2.2.2.2 255.255.255.255 ! interface FastEthernet3/0/0 ip vrf forwarding NEW ip address 110.1.1.1 255.255.255.0 half-duplex ! interface ATM3/1/0.1 tag-switching ip unnumbered Loopback0 tag-switching ip ! router ospf 100 log-adjacency-changes network 2.0.0.0 0.255.255.255 area 0 ! router rip version 2 network 110.0.0.0 no auto-summary ! address-family ipv4 vrf NEW version 2 redistribute bgp 200 metric 0 network 110.0.0.0 no auto-summary exit-address-family ! router bgp 200 bgp log-neighbor-changes neighbor 1.1.1.1 remote-as 200 neighbor 1.1.1.1 update-source Loopback0 no auto-summary ! address-family ipv4 vrf NEW redistribute rip no auto-summary no synchronization exit-address-family ! address-family vpnv4 neighbor 1.1.1.1 activate neighbor 1.1.1.1 send-community extended no auto-summary exit-address-family ! ip classless ! |
CE2 |
---|
! version 12.1 service timestamps debug uptime service timestamps log uptime ! boot system disk0:c7100-jo3s56i-mz.121-5.T.bin ! ip subnet-zero ! interface Loopback0 ip address 30.1.1.1 255.255.255.0 ! interface Loopback1 ip address 30.2.2.2 255.255.255.0 ! interface Loopback2 ip address 30.3.3.3 255.255.255.0 ! interface FastEthernet0/0 ip address 110.1.1.2 255.255.255.0 ! router rip version 2 network 30.0.0.0 network 110.0.0.0 no auto-summary ! |
show Commands
Use these commands to test that your network operates properly:
show ip route - Displays IP routing table entries.
show ip rip database vrf - Shows information contained in the RIP database for a particular VRF.
show ip bgp vpnv4 vrf - Displays VPN address information from the BGP table.
show tag-switching interfaces detail - Displays information about one or more interfaces that have the MPLS feature enabled.
show tag-switching tdp bindings - Displays the requested entries from the ATM LDP label binding database.
show tag-switching forwarding-table vrf - Checks the label stack used for a particular route.
The output shown below is a result of these entered commands on the devices shown in the network diagram. This output shows that the network operates properly.
CE1
Cisco4500#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Ethernet0 110.0.0.0/24 is subnetted, 1 subnets R 110.1.1.0 [120/1] via 100.1.1.1, 00:00:14, Ethernet0 10.0.0.0/24 is subnetted, 3 subnets C 10.3.3.0 is directly connected, Loopback2 C 10.2.2.0 is directly connected, Loopback1 C 10.1.1.0 is directly connected, Loopback0 30.0.0.0/24 is subnetted, 3 subnets R 30.3.3.0 [120/1] via 100.1.1.1, 00:00:14, Ethernet0 R 30.2.2.0 [120/1] via 100.1.1.1, 00:00:15, Ethernet0 R 30.1.1.0 [120/1] via 100.1.1.1, 00:00:15, Ethernet0
PE1
Cisco7500a#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 1.0.0.0/32 is subnetted, 1 subnets C 1.1.1.1 is directly connected, Loopback0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/4] via 4.4.4.4, 18:17:37, ATM2/0/0.10 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/3] via 4.4.4.4, 18:17:37, ATM2/0/0.10 4.0.0.0/32 is subnetted, 1 subnets O 4.4.4.4 [110/2] via 4.4.4.4, 18:17:37, ATM2/0/0.10 Cisco7500a#show ip route vrf NEW Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets C 100.1.1.0 is directly connected, Ethernet2/1/0 110.0.0.0/24 is subnetted, 1 subnets B 110.1.1.0 [200/0] via 2.2.2.2, 00:26:11 10.0.0.0/24 is subnetted, 3 subnets R 10.3.3.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 R 10.2.2.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 R 10.1.1.0 [120/1] via 100.1.1.2, 00:00:11, Ethernet2/1/0 30.0.0.0/24 is subnetted, 3 subnets B 30.3.3.0 [200/1] via 2.2.2.2, 00:26:12 B 30.2.2.0 [200/1] via 2.2.2.2, 00:26:12 B 30.1.1.0 [200/1] via 2.2.2.2, 00:26:12 Cisco7500a#show ip rip database vrf NEW 10.0.0.0/8 auto-summary 10.1.1.0/24 [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 10.2.2.0/24 [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 10.3.3.0/24 [1] via 100.1.1.2, 00:00:18, Ethernet2/1/0 30.0.0.0/8 auto-summary 30.1.1.0/24 redistributed [1] via 2.2.2.2, 30.2.2.0/24 redistributed [1] via 2.2.2.2, 30.3.3.0/24 redistributed [1] via 2.2.2.2, 100.0.0.0/8 auto-summary 100.1.1.0/24 directly connected, Ethernet2/1/0 110.0.0.0/8 auto-summary 110.1.1.0/24 redistributed [1] via 2.2.2.2, Cisco7500a#show ip bgp vpnv4 vrf NEW BGP table version is 17, local router ID is 1.1.1.1 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path Route Distinguisher: 200:1 (default for vrf NEW) *> 10.1.1.0/24 100.1.1.2 1 32768 ? *> 10.2.2.0/24 100.1.1.2 1 32768 ? *> 10.3.3.0/24 100.1.1.2 1 32768 ? *>i30.1.1.0/24 2.2.2.2 1 100 0 ? *>i30.2.2.0/24 2.2.2.2 1 100 0 ? *>i30.3.3.0/24 2.2.2.2 1 100 0 ? *> 100.1.1.0/24 0.0.0.0 0 32768 ? *>i110.1.1.0/24 2.2.2.2 0 100 0 ? Cisco7500a#show tag-switching interfaces Interface IP Tunnel Operational ATM2/0/0.10 Yes No Yes (ATM tagging) Cisco7500a#show tag-switching interfaces detail Interface ATM2/0/0.10: IP tagging enabled TSP Tunnel tagging not enabled Tagging operational Tagswitching turbo vector MTU = 4470 ATM tagging: Tag VPI = 1 Tag VCI range = 33 - 65535 Control VC = 0/32 Cisco7500a#show tag-switching ? atm-tdp ATM Tagging Protocol information cos-map Show Tag CoS ATM Multi-VC CoS Map forwarding-table Show the Tag Forwarding Information Base (TFIB) interfaces Show per-interface tag switching prefix-map Show Tag CoS Prefix Map tdp Tag Distribution Protocol information Cisco7500a#show tag-switching tdp bindings tib entry: 1.1.1.1/32, rev 2 local binding: tag: imp-null tib entry: 2.2.2.2/32, rev 23 local binding: tag: 27 tib entry: 3.3.3.3/32, rev 21 local binding: tag: 26 tib entry: 4.4.4.4/32, rev 10 local binding: tag: 28 Cisco7500a#show tag-switching atm-tdp bindings Destination: 4.4.4.4/32 Headend Router ATM2/0/0.10 (1 hop) 1/33 Active, VCD=24 Destination: 3.3.3.3/32 Headend Router ATM2/0/0.10 (2 hops) 1/43 Active, VCD=25 Destination: 2.2.2.2/32 Headend Router ATM2/0/0.10 (3 hops) 1/42 Active, VCD=26 Destination: 1.1.1.1/32 Tailend Router ATM2/0/0.10 1/33 Active, VCD=24 Cisco7500a#show tag-switching forwarding-table vrf NEW Local Outgoing Prefix Bytes tag Outgoing Next Hop tag tag or VC or Tunnel Id switched interface 29 Aggregate 100.1.1.0/24[V] 2080 30 Untagged 10.3.3.0/24[V] 0 Et2/1/0 100.1.1.2 31 Untagged 10.2.2.0/24[V] 0 Et2/1/0 100.1.1.2 32 Untagged 10.1.1.0/24[V] 0 Et2/1/0 100.1.1.2
P1
LS1010#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route, o - ODR T - traffic engineered route Gateway of last resort is not set 1.0.0.0/32 is subnetted, 1 subnets O 1.1.1.1 [110/2] via 1.1.1.1, 19:00:12, ATM12/0/0 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/3] via 3.3.3.3, 19:00:12, ATM12/0/1 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 3.3.3.3, 19:00:12, ATM12/0/1 4.0.0.0/32 is subnetted, 1 subnets C 4.4.4.4 is directly connected, Loopback0 LS1010#show tag-switching atm-tdp bindings Destination: 4.4.4.4/32 Tailend Switch ATM12/0/0 1/33 Active -> Terminating Active Tailend Switch ATM12/0/1 1/34 Active -> Terminating Active Destination: 2.2.2.2/32 Transit ATM12/0/0 1/42 Active -> ATM12/0/1 1/35 Active Destination: 1.1.1.1/32 Transit ATM12/0/1 1/33 Active -> ATM12/0/0 1/33 Active Destination: 3.3.3.3/32 Transit ATM12/0/0 1/43 Active -> ATM12/0/1 1/34 Active
P2
LS1010#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route, o - ODR Gateway of last resort is 10.118.1.21 to network 0.0.0.0 1.0.0.0/32 is subnetted, 1 subnets O 1.1.1.1 [110/3] via 4.4.4.4, 19:46:00, ATM0/1/1 2.0.0.0/32 is subnetted, 1 subnets O 2.2.2.2 [110/2] via 2.2.2.2, 19:46:00, ATM0/1/3 3.0.0.0/32 is subnetted, 1 subnets C 3.3.3.3 is directly connected, Loopback0 4.0.0.0/32 is subnetted, 1 subnets O 4.4.4.4 [110/2] via 4.4.4.4, 19:46:00, ATM0/1/1 10.0.0.0/24 is subnetted, 1 subnets C 10.118.1.0 is directly connected, Ethernet2/0/0 S* 0.0.0.0/0 [1/0] via 10.118.1.21 LS1010#show tag-switching atm-tdp bindings Destination: 1.1.1.1/32 Transit ATM0/1/3 1/33 Active -> ATM0/1/1 1/33 Active Destination: 3.3.3.3/32 Tailend Switch ATM0/1/3 1/34 Active -> Terminating Active Tailend Switch ATM0/1/1 1/34 Active -> Terminating Active Destination: 4.4.4.4/32 Transit ATM0/1/3 1/35 Active -> ATM0/1/1 1/34 Active Destination: 2.2.2.2/32 Transit ATM0/1/1 1/35 Active -> ATM0/1/3 1/33 Active
PE2
Cisco7500#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 1.0.0.0/32 is subnetted, 1 subnets O 1.1.1.1 [110/4] via 3.3.3.3, 02:58:46, ATM3/1/0.1 2.0.0.0/32 is subnetted, 1 subnets C 2.2.2.2 is directly connected, Loopback0 3.0.0.0/32 is subnetted, 1 subnets O 3.3.3.3 [110/2] via 3.3.3.3, 02:58:46, ATM3/1/0.1 4.0.0.0/32 is subnetted, 1 subnets O 4.4.4.4 [110/3] via 3.3.3.3, 02:58:46, ATM3/1/0.1 Cisco7500#show ip route vrf NEW Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets B 100.1.1.0 [200/0] via 1.1.1.1, 01:16:13 110.0.0.0/24 is subnetted, 1 subnets C 110.1.1.0 is directly connected, FastEthernet3/0/0 10.0.0.0/24 is subnetted, 3 subnets B 10.3.3.0 [200/1] via 1.1.1.1, 01:16:13 B 10.2.2.0 [200/1] via 1.1.1.1, 01:16:13 B 10.1.1.0 [200/1] via 1.1.1.1, 01:16:13 30.0.0.0/24 is subnetted, 3 subnets R 30.3.3.0 [120/1] via 110.1.1.2, 00:00:16, FastEthernet3/0/0 R 30.2.2.0 [120/1] via 110.1.1.2, 00:00:17, FastEthernet3/0/0 R 30.1.1.0 [120/1] via 110.1.1.2, 00:00:17, FastEthernet3/0/0 Cisco7500#show ip rip database vrf NEW 10.0.0.0/8 auto-summary 10.1.1.0/24 redistributed [1] via 1.1.1.1, 10.2.2.0/24 redistributed [1] via 1.1.1.1, 10.3.3.0/24 redistributed [1] via 1.1.1.1, 30.0.0.0/8 auto-summary 30.1.1.0/24 [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 30.2.2.0/24 [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 30.3.3.0/24 [1] via 110.1.1.2, 00:00:09, FastEthernet3/0/0 100.0.0.0/8 auto-summary 100.1.1.0/24 redistributed [1] via 1.1.1.1, 110.0.0.0/8 auto-summary 110.1.1.0/24 directly connected, FastEthernet3/0/0 Cisco7500#show ip bgp vpnv4 vrf NEW BGP table version is 17, local router ID is 2.2.2.2 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric LocPrf Weight Path Route Distinguisher: 200:1 (default for vrf NEW) *>i10.1.1.0/24 1.1.1.1 1 100 0 ? *>i10.2.2.0/24 1.1.1.1 1 100 0 ? *>i10.3.3.0/24 1.1.1.1 1 100 0 ? *> 30.1.1.0/24 110.1.1.2 1 32768 ? *> 30.2.2.0/24 110.1.1.2 1 32768 ? *> 30.3.3.0/24 110.1.1.2 1 32768 ? *>i100.1.1.0/24 1.1.1.1 0 100 0 ? *> 110.1.1.0/24 0.0.0.0 0 32768 ? Cisco7500#show tag-switching interfaces Interface IP Tunnel Operational ATM3/1/0.1 Yes No Yes (ATM tagging) Cisco7500#show tag-switching interfaces detail Interface ATM3/1/0.1: IP tagging enabled TSP Tunnel tagging not enabled Tagging operational Tagswitching turbo vector MTU = 4470 ATM tagging: Tag VPI = 1 Tag VCI range = 33 - 65535 Control VC = 0/32 Cisco7500#show tag-switching ? atm-tdp ATM Tagging Protocol information cos-map Show Tag CoS ATM Multi-VC CoS Map forwarding-table Show the Tag Forwarding Information Base (TFIB) interfaces Show per-interface tag switching prefix-map Show Tag CoS Prefix Map tdp Tag Distribution Protocol information Cisco7500#show tag-switching tdp bindings tib entry: 1.1.1.1/32, rev 25 local binding: tag: 26 tib entry: 2.2.2.2/32, rev 2 local binding: tag: imp-null tib entry: 3.3.3.3/32, rev 27 local binding: tag: 27 tib entry: 4.4.4.4/32, rev 29 local binding: tag: 28 Cisco7500#show tag-switching atm-tdp bindings Destination: 1.1.1.1/32 Headend Router ATM3/1/0.1 (3 hops) 1/33 Active, VCD=8 Destination: 3.3.3.3/32 Headend Router ATM3/1/0.1 (1 hop) 1/34 Active, VCD=6 Destination: 4.4.4.4/32 Headend Router ATM3/1/0.1 (2 hops) 1/35 Active, VCD=7 Destination: 2.2.2.2/32 Tailend Router ATM3/1/0.1 1/33 Active, VCD=8 Cisco7500#show tag-switching forwarding-table vrf NEW Local Outgoing Prefix Bytes tag Outgoing Next Hop tag tag or VC or Tunnel Id switched interface 33 Aggregate 110.1.1.0/24[V] 0 34 Untagged 30.3.3.0/24[V] 0 Fa3/0/0 110.1.1.2 35 Untagged 30.2.2.0/24[V] 0 Fa3/0/0 110.1.1.2 36 Untagged 30.1.1.0/24[V] 0 Fa3/0/0 110.1.1.2
CE2
Cisco7100#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set 100.0.0.0/24 is subnetted, 1 subnets R 100.1.1.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 110.0.0.0/24 is subnetted, 1 subnets C 110.1.1.0 is directly connected, FastEthernet0/0 10.0.0.0/24 is subnetted, 3 subnets R 10.3.3.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 R 10.2.2.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 R 10.1.1.0 [120/1] via 110.1.1.1, 00:00:19, FastEthernet0/0 30.0.0.0/24 is subnetted, 3 subnets C 30.3.3.0 is directly connected, Loopback2 C 30.2.2.0 is directly connected, Loopback1 C 30.1.1.0 is directly connected, Loopback0
Revision | Publish Date | Comments |
---|---|---|
1.0 |
29-Nov-2001 |
Initial Release |