This document provides the technical and cable specifications for the EIA/TIA-449 serial cables.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
For more information on document conventions, see the Cisco Technical Tips Conventions.
The use of balanced drivers allows EIA/TIA-449 signals to travel greater distances than the EIA/TIA-232 standard. The table below lists the standard relationship between baud rate and maximum distance for EIA/TIA-449 signals. These limits are also valid for V.35 and X.21.
Data Rate (Baud) | Distance (Feet) | Distance (Meters) |
---|---|---|
2400 | 4,100 | 1,250 |
4800 | 2,050 | 625 |
9600 | 1,025 | 312 |
19200 | 513 | 156 |
38400 | 256 | 78 |
56000 | 102 | 31 |
T1 | 50 | 15 |
Caution: The EIA/TIA-449 and V.35 interfaces support data rates up to 2.048 Mbps. Exceeding this maximum could result in loss of data and is not recommended.
This section presents the cable assembly and pinouts for the CAB-449MT serial cable.
Note: The cable itself identifies the Cisco router as a data terminal equipment (DTE) or data communications equipment (DCE) device to other devices in the network; for this reason, it is important to select the correct product number from the table below.
The cable gender for this product (part number 72-0795-01) is Male DB-60 to Male DB-37, mode - DTE.
The CAB-449MT cable is used in the Cisco 7000 family, Cisco 4000 series, Cisco 3600 series, Cisco 2500 series, Cisco 1600 series, Cisco access servers, and AccessPro PC cards. This cable has a male DB-60 connector on the Cisco end and a male DB-37 connector on the network end.
The table below shows the EIA/TIA-449 DTE cable pinouts (DB-60 to DB-37).
Note: The arrows indicate signal direction:
---> indicates DTE to DCE
<--- indicates DCE to DTE
60 Pin1 | Signal | Description | Direction | 25 Pin | Signal |
---|---|---|---|---|---|
J1-49 J1-48 | MODE_1 GND | Shorting group | - | - | - |
J1-51 J1-52 | GND MODE_DCE | Shorting group | - | - | - |
J1-46 | Shield_GND | Single | - | J2-1 | Shield GND |
J1-11 J1-12 | TxD/RxD+ TxD/RxD- | Twisted pair no. 6 | ---> ---> | J2-4 J2-22 | SD+ SD- |
J1-24 J1-23 | TxC/RxC+ TxC/RxC- | Twisted pair no. 9 | <--- <--- | J2-5 J2-23 | ST+ ST- |
J1-28 J1-27 | RxD/TxD+ RxD/TxD- | Twisted pair no. 11 | <--- <--- | J2-6 J2-24 | RD+ RD- |
J1-9 J1-10 | RTS/CTS+ RTS/CTS- | Twisted pair no. 5 | ---> ---> | J2-7 J2-25 | RS+ RS- |
J1-26 J1-25 | RxC/TxCE+ RxC/TxCE- | Twisted pair no. 10 | <--- <--- | J2-8 J2-26 | RT+ RT- |
J1-1 J1-2 | CTS/RTS+ CTS/RTS- | Twisted pair no. 1 | <--- <--- | J2-9 J2-27 | CS+ CS- |
J1-44 J1-45 | LL/DCD Circuit_GND | Twisted pair no. 12 | ---> - | J2-10 J2-37 | LL SC |
J1-3 J1-4 | DSR/DTR+ DSR/DTR- | Twisted pair no. 2 | <--- <--- | J2-11 J2-29 | DM+ DM- |
J1-7 J1-8 | DTR/DSR+ DTR/DSR- | Twisted pair no. 4 | ---> ---> | J2-12 J2-30 | TR+ TR- |
J1-5 J1-6 | DCD/DCD+ DCD/DCD- | Twisted pair no. 3 | <--- <--- | J2-13 J2-31 | RR+ RR- |
J1-13 J1-14 | TxCE/TxC+ TxCE/TxC- | Twisted pair no. 7 | ---> ---> | J2-17 J2-35 | TT+ TT- |
J1-15 J1-16 | Circuit_GND Circuit_GND | Twisted pair no. 9 | - - | J2-19 J2-20 | SG RC |
1Any pin not referenced is not connected.
This section presents the cable assembly and pinouts for the CAB-449FC serial cable.
The cable gender for this product (part number 72-0796-01) is Male DB-60 to Female DB-37, mode - DCE.
This cable is used in the following systems:the Cisco 7000 family, Cisco 4000 series, Cisco 3600 series, Cisco 2500 series, Cisco 1600 series, Cisco access servers, and AccessPro PC cards. This cable has a male DB-60 connector on the Cisco end and a female DB-37 connector on the network end.
The table below shows the EIA/TIA-449 DCE cable pinouts (DB-60 to DB-37).
Note: The arrows indicate signal direction:
---> indicates DTE to DCE
<--- indicates DCE to DTE
60 Pin1 | Signal | Description | Direction | 25 Pin | Signal |
---|---|---|---|---|---|
J1-49 J1-48 | MODE_1 GND | Shorting group | - | - | - |
J1-46 | Shield_GND | Single | - | J2-1 | Shield GND |
J1-28 J1-27 | RxD/TxD+ RxD/TxD- | Twisted pair no. 11 | <--- <--- | J2-4 J2-22 | SD+ SD- |
J1-13 J1-14 | TxCE/TxC+ TxCE/TxC- | Twisted pair no. 7 | ---> ---> | J2-5 J2-23 | ST+ ST- |
J1-11 J1-12 | TxD/RxD+ TxD/RxD- | Twisted pair no. 6 | ---> ---> | J2-6 J2-24 | RD+ RD- |
J1-1 J1-2 | CTS/RTS+ CTS/RTS- | Twisted pair no. 1 | <--- <--- | J2-7 J2-25 | RS+ RS- |
J1-24 J1-23 | TxC/RxC+ TxC/RxC- | Twisted pair no. 9 | ---> ---> | J2-8 J2-26 | RT+ RT- |
J1-9 J1-10 | RTS/CTS+ RTS/CTS- | Twisted pair no. 5 | ---> ---> | J2-9 J2-27 | CS+ CS- |
J1-29 J1-30 | NIL/LL Circuit_GND | Twisted pair no. 12 | ---> - | J2-10 J2-37 | LL SC |
J1-7 J1-8 | DTR/DSR+ DTR/DSR- | Twisted pair no. 4 | ---> ---> | J2-11 J2-29 | DM+ DM- |
J1-3 J1-4 | DSR/DTR+ DSR/DTR- | Twisted pair no. 2 | <--- <--- | J2-12 J2-30 | TR+ TR- |
J1-5 J1-6 | DCD/DCD+ DCD/DCD- | Twisted pair no. 3 | ---> ---> | J2-13 J2-31 | RR+ RR- |
J1-26 J1-25 | RxC/TxCE+ RxC/TxCE- | Twisted pair no. 10 | <--- <--- | J2-17 J2-35 | TT+ TT- |
J1-15 J1-16 | Circuit_GND Circuit_GND | Twisted pair no. 8 | - - | J2-19 J2-20 | SG RC |
Revision | Publish Date | Comments |
---|---|---|
1.0 |
08-Sep-2014 |
Initial Release |