Configure Global Green Ethernet Properties on a Switch

Available Languages

Download Options

  • PDF     (674.4 KB)
    View with Adobe Reader on a variety of devices
  • ePub     (790.9 KB)
    View in various apps on iPhone, iPad, Android, Sony Reader, or Windows Phone
  • Mobi (Kindle)     (414.4 KB)
    View on Kindle device or Kindle app on multiple devices
Updated:December 13, 2018
Document ID:SMB2541

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Objective

This article provides instructions on how to configure the global Green Ethernet properties on a switch using the Graphical User Interface (GUI).

If you are interested in configuring using Command Line Interface (CLI), check out this article on Configure Global Green Ethernet Properties on a Switch through the CLI.

Applicable Devices

  • Sx200 Series
  • Sx250 Series
  • Sx300 Series
  • Sx350 Series
  • SG350X Series
  • Sx500 Series
  • Sx550X Series

Software Version

  • 1.4.7.06 - Sx200, Sx300, Sx500
  • 2.2.8.04 - Sx250, Sx350, SG350X, Sx550X

Introduction

Green Ethernet is a common name for a set of features that is designed to be environmentally friendly and reduce the power consumption of a device. Unlike Energy Efficient Ethernet (EEE), Green Ethernet energy-detection is enabled on all ports whereas only devices with gigabyte ports are enabled with EEE.

The Green Ethernet feature can reduce overall power usage in the following ways:

  • Energy Detect Mode - On an inactive link, the port moves into inactive mode and saves power while keeping the Administrative status of the port Up. Recovery from this mode to full operational mode is fast, transparent, and no frames are lost. This mode is supported on both Gigabit Ethernet (GE) and Fast Ethernet (FE) ports. This mode is disabled by default.
  • Short Reach Mode - This feature provides power savings on a short length of cable. After cable length is analyzed, the power usage is adjusted for various cable lengths. If the cable is shorter than 30 meters for Ten-Gigabit ports and 50 meters for other type of ports, the device uses less power to send frames over the cable, thus saving energy. This mode is only supported on RJ45 GE ports and does not apply to Combo ports. This mode is disabled by default.

Configure Global Green Ethernet Properties on a Switch

Step 1. Log in to the web-based utility of your switch then choose Port Management > Green Ethernet > Properties.

Note: The available options may vary depending on the exact model of your device. In this example, SG350X-48MP switch is used.

Step 2. (Optional) To configure Green Ethernet settings per port, click the Port Settings link. For instructions, click here.

Step 3. To enable the Energy Detect Mode feature on the switch, check the Enable Energy Detect Mode check box. Otherwise, leave it unchecked. This is used to conserve power when the device is not connected to an active link partner.

Note: If you have an XG switch, Energy Detect Mode and Short Reach features are always enabled.

Step 4. Check the Enable Short Reach check box to enable the Short Reach feature. Otherwise, leave it unchecked. This allows you to run the links with less power than the link can normally handle.

Important: If Short Reach Mode is enabled, the EEE mode must be disabled.

Step 5. Check the Enable Port LEDs check box to enable the port Light-emitting Diodes (LEDs). When this option is disabled, the LEDs do not display link status, activity, and so on.

The Power Savings area displays the amount of power saved when Green Ethernet and Short Reach mode are run. EEE power savings is not taken into account since it is dynamic and corresponds to port utilization.

Note: This area is available on Sx200, Sx250, Sx300, Sx500, and XG switches.

The Cumulative Energy Saved area shows the amount of energy saved from the last switch reboot. This value is updated each time there is an event that affects power saving.

Note: This area is available on Sx200, Sx250, Sx300, Sx500, and XG switches.

Step 6. If there are Gigabit Ethernet ports on the switch, check the Enable 802.3 Energy Efficient Ethernet (EEE) check box enable 802.3 EEE mode. By default, this is enabled. EEE was developed to reduce the power consumption during times that there is a low amount of data activity on the switch.

Note: In this example, 802.3 Energy Efficient Ethernet (EEE) is disabled.

Step 7. Click Apply.

SG350X and Sx550X Series Switches:

Sx200, Sx250, Sx300, and Sx500 Series Switches:

XG Switches:

Step 8. (Optional) If 802.3 Energy Efficient Ethernet (EEE) is disabled in Step 6, click OK to proceed.

Step 9. (Optional) To disregard the configured settings, click the Cancel button.

Step 10. (Optional) To reset the Cumulative Energy Saved information, click the Reset Energy Saving Counter button.

Step 11. (Optional) Click OK to continue.

Step 12. (Optional) Click Save to save the settings to the startup configuration file.

You should now have successfully configured the global Green Ethernet properties of your switch.

Revision History

Revision Publish Date Comments
1.0
13-Dec-2018
Initial Release

Was this Document Helpful?

FeedbackFeedback

Contact Cisco