Contents

Introduction

Prerequisites

Requirements

Components Used

Conventions

Configure

AS5300: Cisco IOS - Voice Feature Card (VFC) Software Compatibility

Configure E1 R2

Network Diagram

Configurations

Verify

Troubleshoot

Troubleshoot E1 R2 Failures

debug and show Commands

Sample Debug Output

Related Information

Introduction

This document offers the progressive command entries that are necessary in order to implement E1 R2 signaling. This document also offers troubleshooting information with debug commands.

Note: Before you use this document, it is recommended that you first read E1 R2 Signaling Theory.

Prerequisites

Requirements

Before you attempt this configuration, ensure that you meet these prerequisites:

- R2 signaling applies to E1 only.

- R2 signaling is not supported on the Cisco MC3810 router.

- In order to run R2 signaling on Cisco 2600/3600 series routers, this hardware is required:

VWIC-1MFT-E1 or VWIC-2MFT-E1 or VWIC-2MFT-E1-DI along with one of these voice density modules: NM-HDV (High Density Voice Network Module) or NM-HD-2VE (2-slot IP communications voice/fax network module ) .

- Define the command ds0-group (or cas-group, based on the Cisco IOS® version) on the E1 controllers (AS5x00, Cisco 2600/3600 routers).

- Use the command cas-custom in order to customize the E1 R2 variants for different countries or regions.

Components Used

The information in this document is based on this software and hardware version:

- Cisco AS5300 with Cisco IOS Software Release 12.0.7T

Note: E1 R2 signaling was introduced to the Cisco 2600/3600 series routers in Cisco IOS Software Releases 12.1.2XH and 12.1(3)T.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

Configure

This section presents you with the information you can use in order to configure E1 R2.

Note: In order to find additional information on the commands this document uses, refer to the Command Lookup Tool (registered customers only) .

AS5300: Cisco IOS - Voice Feature Card (VFC) Software Compatibility

Before you implement E1 R2 signaling in a Cisco AS5300 router, ensure that your version of Cisco IOS software is compatible with the Cisco VCware in the E1 module. In order to verify the Cisco IOS software compatibility, refer to the Cisco VCWare Compatibility Matrix for the Cisco AS5300. If the versions are incompatible, the digital signal processor (DSP) modules in the voice card do not load and voice signal processing does not occur.

Typically, if the version of Cisco VCWare is incompatible with the Cisco IOS software, you can enter the show vfc slot_number interface command in order to see this as shown in this example.

eefje#show vfc 1 interface

Rx: in ptr 18, outptr 0

Tx: in ptr 14  outptr  14

0 in hw queue, 0 queue head , 0 queue tail

Hardware is VFC out-of-band channel

Interface : state RESET DSP instance (0x61048284)

dsp_number 0, Channel ID 0

TX outstanding 0, max TX outstanding 0

Received 18 packets, 1087 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

121 bytes output, 14 frames output

0 bounce errors 0

DSP module 1 is not installed

DSP module 2 is not installed

DSP module 3 is not installed

DSP module 4 is not installed

DSP module 5 is not installed

In the first example output of the show vfc slot_number interface command, the DSP module number is not installed statements show that the versions are incompatible for that module number.

This second set of output is an example of the DSP modules that have the correct Cisco VCWare version loaded:

eefje#show vfc 1 interface

Rx: in ptr 24, outptr 0

TX: in ptr 15  outptr  15

0 in hw queue, 0 queue head , 0 queue tail

Hardware is VFC out-of-band channel

Interface : state RESET DSP instance (0x618C6088)

dsp_number 0, Channel ID 0

TX outstanding 0, max TX outstanding 0

Received 283288 packets, 15864278 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

1416459 bytes output,  141647 frames output

0 bounce errors 0

Slot 1, DSPM 1 (C542), DSP 1, Channel 1

State RESET, DSP instance (0x61914BDC)

TX outstanding 0, max TX outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output,  0 frames output

0 bounce errors 0

Slot 1, DSPM 1 (C542), DSP 2, Channel 1

State RESET, DSP instance (0x6191510C)

TX outstanding 0, max TX outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output,  0 frames output

0 bounce errors 0

In order to check the installed Cisco VCWare version, enter the command show vfc slot_number version vcware, as shown in this example:

eefje#show vfc 1 version vcware

Voice Feature Card in Slot 1:

VCware Version : 4.10

ROM Monitor Version : 1.2

DSPware Version :

Technology :  C542

Note: Make sure the Cisco VCWare technology version (c549 or c542) matches the installed VFC DSP technology (DSPM-542: single-density voice support or DSPM-549: high-density voice support).

Configure E1 R2

Complete these steps in order to configure E1 R2:

1. Set up the controller E1 that connects to the private automatic branch exchange (PBX) or switch.

Ensure that the framing and linecoding of the E1 are properly set.

2. For E1 framing, choose either CRC or non-CRC.

3. For E1 linecoding, choose either HDB3 or AMI.

4. For the E1 clock source, choose either internal or line. Keep in mind that different PBXs have different requirements on the clock source.

5. Configure line signaling.

6. Configure interregister signaling.

7. Customize the configuration with the cas-custom command.

Configure Line Signaling

Use this command sequence in order to define your line signaling.

eefje(config)#controller E1 0

eefje(config-controller)#ds0-group 1 timeslots 1-15 type ?

...

r2-analog        R2 ITU Q411

r2-digital       R2 ITU Q421

r2-pulse         R2 ITU Supplement 7

...

This is the command sequence for Cisco IOS Software Release 11.3.

eefje(config)#controller E1 0

eefje(config-controller)#cas-group 1 timeslot 1-15 type ?

...

Note: If you upgrade from Cisco IOS Software Release 11.3 to 12.0, the new command replaces the old one automatically.

Configure Interregister Signaling

This command sequence example illustrates how to configure the different types of interregister signaling:

eefje(config)#controller E1 0

eefje(config-controller)#ds0-group 1 timeslots 1-15 type r2-digital ?

dtmf               DTMF tone signaling

r2-compelled       R2 Compelled Register Signaling

r2-non-compelled   R2 Non Compelled Register Signaling

r2-semi-compelled  R2 Semi Compelled Register Signaling

The Cisco implementation of R2 signaling has Dialed Number Identification Service (DNIS) support enabled by default. If you enable the Automatic Number Identification (ANI) option, the collection of DNIS information is still performed. Specification of the ANI option does not disable DNIS collection. DNIS is the number that is called. ANI is the number of the caller. For example, if you configure a router called A to call a router called B, then the DNIS number is assigned to router B and the ANI number is assigned to router A. ANI is similar to caller ID.

E1 R2 Customization with the cas-custom Command

The subcommands under the command cas-custom are used in order to accommodate the country variants. They are also used in order to customize channel associated signaling (CAS) parameters. This command sequence illustrates how you can view all cas-custom command options.

eefje(config)#controller E1 0

eefje(config-controller)#cas-custom 1

eefje(config-ctrl-cas)#?

CAS custom commands:

ani-digits           Expected number of ANI digits

ani-timeout          Timeout for ANI digits

answer-guard-time    Wait Between Group-B Answer Signal And Line Answer

answer-signal        Answer signal to be used

caller-digits        Digits to be collected before requesting CallerID

category             Category signal

country              Country Name

debounce-time        Debounce Timer

default              Set a command to its defaults

dnis-complete        Send I-15 after DNIS digits for dial-out

dnis-digits          Expected number of DNIS digits

exit                 Exit from cas custom mode

groupa-callerid-end  Send Group-A Caller ID End

invert-abcd          invert the ABCD bits before TX and after rx

ka                   kA Signal

kd                   KD Signal

metering             R2 network is sending metering signal

nc-congestion        Non Compelled Congestion signal

no                   Negate a command or set its defaults

proceed-to-send      Suppress proceed-to-send signal for pulsed line signaling

release-ack          Send Release Acknowledgment to Clear Forward

release-guard-time   Release Guard Timer

request-category     DNIS Digits to be collected before requesting category

seizure-ack-time     Seizure to Acknowledge timer

unused-abcd          Unused ABCD bit values

For more information on the cas-custom command parameters, refer to E1 R2 Customization with the cas-custom command.

Network Diagram

This document uses this network setup.

Configurations

For the purpose of this document, these are the three different R2 configurations which are shown across the E1 interface:

- R2 Digital Non-compelled

- R2 Digital Semi-compelled

- R2 Digital Compelled ANI

The configurations have been modified in order to show only the information that this document discusses.

eefje Configured for R2 Digital Non-Compelled

hostname eefje

!

controller E1 0

clock source line primary

dso-group 1 timeslots 1-15 type r2-digital r2-non-compelled

cas-custom 1

!--- For more information on these commands !--- refer to  ds0-group  and  cas-custom.

!

voice-port 0:1

cptone BE

!--- The cptone command is country specific. For more !--- information on this command, refer to  cptone .

!

dial-peer voice 123 pots

destination-pattern 123

direct-inward-dial

port 0:1

prefix 123

!

dial-peer voice 567 voip

destination-pattern 567

session target ipv4:2.0.0.2

!

eefje Configured for R2 Digital Semi-Compelled

hostname eefje

!

controller E1 0

clock source line primary

ds0-group 1 timeslots 1-15 type r2-digital r2-semi-compelled

cas-custom 1

!--- For more information on these commands !--- refer to  ds0-group  and  cas-custom .

!

voice-port 0:1

cptone BE

!--- The cptone command is country specific. For more !--- information on this command, refer to  cptone .

dial-peer voice 123 pots

destination-pattern 123

direct-inward-dial

port 0:1

prefix 123

!

dial-peer voice 567 voip

destination-pattern 567

session target ipv4:2.0.0.2

!

eefje Configured for R2 Digital Compelled ANI

hostname eefje

! controller E1 0 clock source line primary ds0-group

1 timeslots 1-15 type r2-digital r2-compelled ani cas-custom 1

!--- For more information on these commands !--- refer to  ds0-group  and  cas-custom .

voice-port 0:1 cptone BE

!--- The cptone command is country specific. For more !--- information on this command, refer to  cptone .

dial-peer voice 123 pots destination-pattern 123 direct-inward-dial port

0:1 prefix 123

!

dial-peer voice 567 voip destination-pattern 567 session

target ipv4:2.0.0.2

!

Verify

There is currently no verification procedure available for this configuration.

Troubleshoot

This section provides information you can use to troubleshoot your configuration.

Troubleshoot E1 R2 Failures

This is the troubleshooting information relevant to this configuration. Follow these instructions in order to troubleshoot your configuration.

1. Verify that controller E1 0 is up.

If it is down, check framing, line coding, clock source, alarms, replace the cable, reseat the card, and so forth . Use the E1 R2 Customization with the cas-custom Command document as a reference.

2. If you use an AS5300, check that the DSPs are correctly installed with the show vfc slot number interface command.

3. Configure direct inward dial (DID) on the plain old telephone service (POTS) peer, so that the received digits are used to choose an outgoing peer.

4. Specify cptone (cptone is specific for your country) on the voice-ports.

A cptonecountry command must be configured in order to match cas-custom country command. The cptone parameter sets the call progress tones for a particular country, and more importantly sets the encoding to a-law or u-law, which depends on the country. The default encoding for the US is u-law.

5. Match line and register signaling provisions to the switch configuration.

6. Turn on some of the debugs shown in this document and study the outputs.

7. Check for communication between the router and PBX or switch:

- Is the line seized?

- Does the router receive/send digits?

- Find out which side clears the call.

If possible, use the latest Cisco IOS software releases available on Cisco.com.

debug and show Commands

Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.

Note: Before you issue debug commands, refer to the Important Information on Debug Commands.

Note: For Cisco IOS Software Release 12.0, use these debugs:

- debug cas - For line signaling.

- debug csm voice - For interregister signaling.

- debug vtsp all - In order to have the output of all messages (digits) exchanged between the PBX and the router.

For Cisco IOS Software Release IOS 11.3, use these commands:

- modem-mgmt csm debug-rbs - For line signaling (You need to specify service internal in config mode first.).

- debug csm voice - For interregister signaling.

- debug vtsp all - In order to have the output of all messages (digits) exchanged between the PBX and the router.

For the AS5400 and AS5350 platforms, use these debugs:

- debug sigsm r2 - For interregister signaling

- debug vtsp all - In order to have the output of all messages (digits) exchanged between the PBX and the router.

Sample Debug Output

Since there are three different configurations previously shown in this document, here are three different debugs:

R2 Digital Non-compelled: Incoming Call to 567

In order to understand this debug output better, refer to E1 R2 Signaling Theory.

eefje#show debug

CAS:

Channel Associated Signaling debugging is on

CSM Voice:

Voice Call Switching Module debugging is on

Voice Telephony session debugging is on

Voice Telephony dsp debugging is on

Voice Telephony error debugging is on

eefje#

eefje#

eefje#

Jan 6 10:41:28.677: from NEAT(0): (0/0): Rx SEIZURE (ABCD=0001)

Jan 6 10:41:28.717: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:28.717: VDEV_ALLOCATE: 1/28 is allocated

Jan 6 10:41:28.721: csm_vtsp_init_tdm (voice_vdev=0x620BF874)

Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2,

dspm 1, dsp 5, dsp_channel 1

Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5,

channel 3, bank 1, bp_channel 4, BP_stream 255

Jan 6 10:41:28.721: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0018): EVENT_CALL_DIAL_IN

at slot 2 and port 16

Jan 6 10:41:28.721: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 2,

port 16

Jan 6 10:41:28.721: csm_vtsp_start_digit_collect (voice_vdev=0x620BF874)

Jan 6 10:41:28.721:  Enter csm_connect_pri_vdev function

Jan 6 10:41:28.721: csm_connect_pri_vdev:tdm_allocate_BP_ts()call. BP TS allocated

at BP_stream0, BP_Ch28,vdev_common 0x6 20BF8E4

Jan 6 10:41:28.721: to NEAT:(cid0018) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan0

Jan 6 10:41:28.721: vtsp_do_call_setup_ind

Jan 6 10:41:28.721: vtsp_do_call_setup_ind: Call ID=65681, guid=61FAF610

Jan 6 10:41:28.721: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0,

id1=0, id2=0, calling=, called=

Jan 6 10:41:28.721: vtsp_do_call_setup_ind: redirect DN = reason =

0vtsp_open_voice_and_set_params

Jan 6 10:41:28.721: dsp_close_voice_channel: [0:1:0] packet_len=8 channel_id

=8529 packet_id=75

Jan 6 10:41:28.721: dsp_open_voice_channel_20: [0:1:0] packet_Len=16 channel_id

=8529 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0

serial_port=0

Jan 6 10:41:28.721: dsp_encap_config_20: [0:1:0] packet_Len=24 channel_id=8529

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 10:41:28.721: dsp_set_playout: [0:1:0] packet_Len=18 channel_id=8529

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 6 10:41:28.721: dsp_echo_canceller_control: [0:1:0] packet_Len=10

channel_id=8529 packet_id=66 flags=0x0

Jan 6 10:41:28.721: dsp_set_gains: [0:1:0] packet_Len=12 channel_id=8529

packet_id=91 in_gain=0 out_gain=0

Jan 6 10:41:28.721: dsp_vad_enable: [0:1:0] packet_Len=10 channel_id=8529

packet_id=78 thresh=-38

Jan 6 10:41:28.721: dsp_voice_mode: [0:1:0] packet_Len=24 channel_id=8529

packet_id=73 coding_type=1 voice_field_size=80 V AD_flag=0 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2

AGC_flag=0vtsp_do_r2_start_digit(): dsp_dtmf_mode()

dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE)

Jan 6 10:41:28.725: dsp_dtmf_mode: [0:1:0] packet_Len=10 channel_id=8529

packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit():fsm_push(vtsp_r2_state_table)

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp (vdev_info=0x620BF874,

vtsp_cdb=0x621C5F3C)

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat

BP_stream0,BP_Ch28

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:dst_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 255, BP_ch 4

Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 0, BP_ch 28

Jan 6 10:41:28.725: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK

(DNIS=, ANI=) at slot 2, port 16

Jan 6 10:41:28.725: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_IDLE R2

Got Event R2_START

Jan 6 10:41:28.821: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):EVENT_START_RX_TONE at slot 2

and port 16

Jan 6 10:41:28.821: from NEAT(0): (0/0): TX SEIZURE_ACK (ABCD=1101)

!--- Digit 5 is sent: Forward Signal Group I-5.

Jan 6 10:41:29.233: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=5,

rtp_timestamp=0x0CA95D43 dc_digit_up

Jan 6 10:41:29.233: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 10:41:29.233: CSM voice (2/16): Rcvd Digit detected(5)

Jan 6 10:41:29.233: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event 5

Jan 6 10:41:29.365: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5,

duration=8321dc_digit

Jan 6 10:41:29.365: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 10:41:29.365: CSM voice (2/16): Rcvd Digit detected(5)

Jan 6 10:41:29.365: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 6 is sent: Forward Signal Group I-6.

Jan 6 10:41:29.593: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=6,

rtp_timestamp=0x0CA95D43 dc_digit_up

Jan 6 10:41:29.593: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (6)

Jan 6 10:41:29.593: CSM voice (2/16): Rcvd Digit detected(6)

Jan 6 10:41:29.593: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event 6

Jan 6 10:41:29.725: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6,

duration=8321dc_digit

Jan 6 10:41:29.725: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6)

Jan 6 10:41:29.725: CSM voice (2/16): Rcvd Digit detected(6)

Jan 6 10:41:29.725: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 7 is sent: Forward Signal Group I-7.

Jan 6 10:41:29.953: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=7, rtp_timestamp=0x0CA95D43 dc_digit_up

Jan 6 10:41:29.953: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)

received digit (7)

Jan 6 10:41:29.953: CSM voice (2/16): Rcvd Digit detected(7)

Jan 6 10:41:29.953: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 7

Jan 6 10:41:30.085: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:

digit=7, duration=8321dc_digit

Jan 6 10:41:30.085: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (7)

Jan 6 10:41:30.085: CSM voice (2/16): Rcvd Digit detected(7)

Jan 6 10:41:30.085: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Timeout: 3 seconds (default timer - AS5300 assumes DNIS is finished).

Jan 6 10:41:32.953: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_TIMER

!--- Send digit 6: Backward Signal Group B-6 (subscriber's line free-charge).

Jan 6 10:41:32.953: vtsp_r2_generate_digits: vdev_common=0x620BF8E4,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6#

Jan 6 10:41:32.953: dsp_dtmf_dialing: [0:1:0] packet_Len=36 channel_id=8529

packet_id=90 string=6# digits=2, time_on=150, time_off=30

Jan 6 10:41:32.953:&   digit=e, components=2, freq_of_first=900,

freq_of_second=780, amp_of_first=8192, amp_of_second=8192

Jan 6 10:41:32.953:    digit=o, components=2, freq_of_first=0,

freq_of_second=0, amp_of_first=1, amp_of_second=1

Jan 6 10:41:33.313: vtsp_process_dsp_message:

MSG_TX_DIALING_DONE dc_dialing_done()

Jan 6 10:41:33.313: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE:R2_IN_ANSWER_PULSE R2

Got Event R2_DIGITS_GENR2_ALERTING

Jan 6 10:41:34.313: R2 Incoming Voice(2/16): DSX (E1 0:0):

STATE: R2_IN_ANSWER_PULSE R2

Got Event R2_TONE_TIMER

Jan 6 10:41:34.313:  R2_IN_IDLE:2 r2_in_connect called

Jan 6 10:41:34.313: CSM_PROC_IC1_COLLECT_ADDR_INFO:

CSM_EVENT_ADDR_INFO_COLLECTED (DNIS=567, ANI=) at slot 2, port 16

Jan 6 10:41:34.313: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0, calling_number=

called_number=567): peer_tag=0

Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device

Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 10:41:34.313: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2,

port 16

Jan 6 10:41:34.313: vtsp_ic_switch : (voice_vdev= 0x620BF874)

Jan 6 10:41:34.313: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C, tsp_info=0x620BF874,

calling_number= called_number=567 redir ect_number=):

peer_tag=123dc_switch: fsm_pop()

Jan 6 10:41:34.313: vtsp_do_call_setup_ind

Jan 6 10:41:34.313: vtsp_do_call_setup_ind: Call ID=65683, guid=61FAF610

Jan 6 10:41:34.313: vtsp_do_call_setup_ind: type=0, under_spec=0,

name=ab^Lx, id0=1, id1=0, id2=0, calling=123, called=567

Jan 6 10:41:34.317: dsp_cp_tone_off: [] packet_Len=8 channel_id=8529 packet_id=71

Jan 6 10:41:34.317: dsp_idle_mode: [] packet_Len=8 channel_id=8529 packet_id=68

Jan 6 10:41:34.317: dsp_close_voice_channel: [] packet_Len=8 channel_id=8529

packet_id=75

Jan 6 10:41:34.317: vtsp_timer_stop: 67475758

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp (vdev_info=0x620BF874,

vtsp_cdb=0x621C5F3C)

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:vdev_common

BP TS allocatedat BP_stream0,

BP_Ch28

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 0, BP_ch 28

Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 5, chan 3,BP_stream 0, BP_ch 28vt sp_open_voice_and_set_params

Jan 6 10:41:34.317: dsp_close_voice_channel: [0:1 (54)] packet_Len=8 channel_id=8529

packet_id=75

Jan 6 10:41:34.317: dsp_open_voice_channel_20: [0:1 (54)] packet_Len=16

channel_id=8529

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0

serial_port=0

Jan 6 10:41:34.317: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 10:41:34.317: dsp_set_playout: [0:1 (54)] packet_Len=18 channel_id=8529

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 6 10:41:34.317: dsp_echo_canceller_control: [0:1 (54)] packet_Len=10

channel_id=8529

packet_id=66 flags=0x0

Jan 6 10:41:34.317: dsp_set_gains: [0:1 (54)] packet_Len=12

channel_id=8529 packet_id=91

in_gain=0 out_gain=0

Jan 6 10:41:34.317: dsp_vad_enable: [0:1 (54)] packet_Len=10

channel_id=8529 packet_id=78

thresh=-38act_proceeding

Jan 6 10:41:34.321: csm_vtsp_call_proceeding:DST_tdm_chnl call.

BP TS allocatedstream 5,

chan 3,BP_stream 0, BP_ch 28act_alert

Jan 6 10:41:34.345: vtsp_ring_noan_timer_start: 67475761

Jan 6 10:41:34.345: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)act_bridge act_caps_ind

Jan 6 10:41:34.589: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20,

FaxRate 2, FaxBytes 20 SignalType 0

DtmfRelay 1, Modem 1act_caps_ack

Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8

channel_id=8529 packet_id=68

Jan 6 10:41:34.589: act_caps_ack: codec = 15, ret = 1

Jan 6 10:41:34.589: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529

packet_id=71

Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8

channel_id=8529 packet_id=68

Jan 6 10:41:34.589: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 10:41:34.589: dsp_voice_mode: [0:1 (54)] packet_Len=24 channel_id=8529

packet_id=73 coding_type=20 voice_field_size=20 VAD_flag=1 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect

Jan 6 10:41:36.857: vtsp_ring_noan_timer_stop: 67476012

Jan 6 10:41:36.857: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529

packet_id=71

Jan 6 10:41:36.857: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C,

voice_vdev=0x620BF874)

Jan 6 10:41:36.857: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK

at slot 2, port 16

Jan 6 10:41:36.917: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):  EVENT_CHANNEL_CONNECTED

at slot 2 and port 16

Jan 6 10:41:36.917: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED

at slot 2, port 16

Jan 6 10:41:36.921: from NEAT(0): (0/0): TX ANSWERED(ABCD=0101)

eefje#

R2 Digital Semi-compelled: Incoming Call to 567

In order to understand this debug output better, refer to E1 R2 Signaling Theory.

eefje#show debug

CAS:

Channel Associated Signaling debugging is on

CSM Voice:

Voice Call Switching Module debugging is on

Voice Telephony session debugging is on

Voice Telephony dsp debugging is on

Voice Telephony error debugging is on

eefje#

eefje#

eefje#

Jan  6 09:53:42.389: from NEAT(0): (0/2): Rx SEIZURE(ABCD=0001)

Jan 6 09:53:42.433: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:42.433: VDEV_ALLOCATE: 1/27 is allocated

Jan 6 09:53:42.433: csm_vtsp_init_tdm (voice_vdev=0x620BF320)

Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2, dspm 1,

dsp 4, dsp_channel 4

Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 7, channel 0,

bank 4, BP_channel 3, BP_stream 255

Jan 6 09:53:42.433: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0017): EVENT_CALL_DIAL_IN

at slot 2 and port 15

Jan 6 09:53:42.433: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT

at slot 2, port 15

Jan 6 09:53:42.433: csm_vtsp_start_digit_collect (voice_vdev=0x620BF320)

Jan 6 09:53:42.433:  Enter csm_connect_pri_vdev function

Jan 6 09:53:42.433: csm_connect_pri_vdev:tdm_allocate_BP_Ts()call. BP TS allocated

at BP_stream0, BP_Ch27,vdev_common 0x6 20BF390

Jan 6 09:53:42.433: to NEAT:(cid0017) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan2

Jan 6 09:53:42.433: vtsp_do_call_setup_ind

Jan 6 09:53:42.433: vtsp_do_call_setup_ind: Call ID=65675, guid=61FAF610

Jan 6 09:53:42.433: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0,

id1=0, id2=0, calling=, called=

Jan 6 09:53:42.433: vtsp_do_call_setup_ind: redirect DN = reason =

0vtsp_open_voice_and_set_params

Jan 6 09:53:42.433: dsp_close_voice_channel: [0:1:2] packet_Len=8 channel_id=8516

packet_id=75

Jan 6 09:53:42.433: dsp_open_voice_channel_20: [0:1:2] packet_Len=16

channel_id=8516

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=1 serial_port=1

Jan 6 09:53:42.433: dsp_encap_config_20: [0:1:2] packet_Len=24 channel_id=8516

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 09:53:42.433: dsp_set_playout: [0:1:2] packet_Len=18 channel_id=8516

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 6 09:53:42.433: dsp_echo_canceller_control: [0:1:2]

packet_Len=10 channel_id=8516

packet_id=66 flags=0x0

Jan 6 09:53:42.437: dsp_set_gains:[0:1:2] packet_Len=12

channel_id=8516 packet_id=91

in_gain=0 out_gain=0

Jan 6 09:53:42.437: dsp_vad_enable: [0:1:2] packet_Len=10 channel_id=8516

packet_id=78 thresh=-38

Jan 6 09:53:42.437: dsp_voice_mode: [0:1:2] packet_Len=24 channel_id=8516

packet_id=73 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0vtsp_do_r2_start_digit():

dsp_dtmf_mode() dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE)

Jan 6 09:53:42.437: dsp_dtmf_mode: [0:1:2] packet_Len=10 channel_id=8516

packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table)

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp (vdev_info=0x620BF320,

vtsp_cdb=0x621C5F3C)

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:vdev_common BP

TS allocatedat BP_stream0,

BP_Ch27

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 255, BP_ch 3

Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 0, BP_ch 27

Jan 6 09:53:42.437: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK

(DNIS=, ANI=) at slot 2, port 15

Jan 6 09:53:42.437: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_IDLE R2

Got Event R2_START

Jan 6 09:53:42.533: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):EVENT_START_RX_TONE

at slot 2 and port 15

Jan 6 09:53:42.533: from NEAT(0): (0/2): TX SEIZURE_ACK (ABCD=1101)

!--- Digit 5 is sent: Forward Signal Group I-5.

Jan 6 09:53:42.641: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=5, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:42.641: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 09:53:42.641: CSM voice (2/15): Rcvd Digit detected(5)

Jan 6 09:53:42.641: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 5

!--- Digit 1 sent (pulse): Backward Signal Group A-1 (Send next digit) !--- "#" this indicates that it is a pulse).

Jan 6 09:53:42.641: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:42.641: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=1# digits=2, time_on=150, time_off=30

Jan 6 09:53:42.641:    digit=`, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:42.641:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:42.741: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5,

duration=8291dc_digit

Jan 6 09:53:42.741: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5)

Jan 6 09:53:42.741: CSM voice (2/15): Rcvd Digit detected(5)

Jan 6 09:53:42.741: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 6 is sent: Forward Signal Group I.

Jan 6 09:53:42.881: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=6, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:42.881: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (6)

Jan 6 09:53:42.881: CSM voice (2/15): Rcvd Digit detected(6)

Jan 6 09:53:42.881: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 6

!--- Digit 1 sent (pulse): Backward Signal Group A-1. (Send next digit.)

Jan 6 09:53:42.881: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=56dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:42.881: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=1# digits=2, time_on=150, time_off=30

Jan 6 09:53:42.881:    digit=`, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:42.881:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:42.981: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6,

duration=8291dc_digit

Jan 6 09:53:42.981: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6)

Jan 6 09:53:42.981: CSM voice (2/15): Rcvd Digit detected(6)

Jan 6 09:53:42.981: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

!--- Digit 7 is sent: Forward Signal Group I-7.

Jan 6 09:53:43.121: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=7, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:43.121: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (7)

Jan 6 09:53:43.121: CSM voice (2/15): Rcvd Digit detected(7)

Jan 6 09:53:43.121: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 7

!--- Send digit 1 (pulse): Backward Signal Group A-1.

Jan 6 09:53:43.121: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1#

Jan 6 09:53:43.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=1# digits=2, time_on=150, time_off=30

Jan 6 09:53:43.121:    digit=`, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:43.121:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:43.221: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7,

duration=8291dc_digit

Jan 6 09:53:43.221: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (7)

Jan 6 09:53:43.221: CSM voice (2/15): Rcvd Digit detected(7)

Jan 6 09:53:43.221: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 6 09:53:43.489: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

!--- Timeout is 3 seconds.

Jan 6 09:53:46.121: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_TIMER

!--- Digit 3 sent(pulse): Backward Signal Group A-3. !--- (Address-complete, changeover to reception of Group-B signals).

Jan 6 09:53:46.121: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3#

Jan 6 09:53:46.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=3# digits=2, time_on=150, time_off=30

Jan 6 09:53:46.121:    digit=b, components=2, freq_of_first=1020,

freq_of_second=900,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:46.121:    digit=o, components=2, freq_of_first=0,

freq_of_second=0, amp_of_first=1, amp_of_second=1

!--- Digit 1 is sent: Forward Signal Group II-1 !--- (subscriber without priority).

Jan 6 09:53:46.361: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=1, rtp_timestamp=0x9330B42B dc_digit_up

Jan 6 09:53:46.361: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)

received digit (1)

Jan 6 09:53:46.361: CSM voice (2/15): Rcvd Digit detected(1)

Jan 6 09:53:46.361: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_CATEGORY R2

Got Event 1

Jan 6 09:53:46.361:  r2_comp_category:R2_ALERTING

!--- Digit 6 sent (pulse): Backward Signal Group B-6 !--- (the subscriber line free of charge).

Jan 6 09:53:46.361: vtsp_r2_generate_digits: vdev_common=0x620BF390,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6#

Jan  6 09:53:46.361: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516

packet_id=90 string=6# digits=2, time_on=150, time_off=30

Jan 6 09:53:46.361:    digit=e, components=2, freq_of_first=900,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 6 09:53:46.361:    digit=o, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 6 09:53:46.461: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=1,

duration=8291dc_digit

Jan 6 09:53:46.461: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (1)

Jan 6 09:53:46.461: CSM voice (2/15): Rcvd Digit detected(1)

Jan 6 09:53:46.461: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COMPLETE R2

Got Event R2_TONE_OFF

Jan 6 09:53:46.729: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

Jan 6 09:53:47.461: R2 Incoming Voice(2/15): DSX (E1 0:2):

STATE:R2_IN_WAIT_GUARD R2

Got Event R2_TONE_TIMER

Jan 6 09:53:47.461:  R2_IN_IDLE:2 r2_in_connect called

Jan 6 09:53:47.461: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_ADDR_INFO_COLLECTED

(DNIS=567, ANI=) at slot 2, port 15

Jan 6 09:53:47.461: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0,calling_number=

called_number=567): peer_tag=0

Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device

Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem

Jan 6 09:53:47.461: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2,

port 15

Jan 6 09:53:47.461: vtsp_IC_switch : (voice_vdev= 0x620BF320)

Jan 6 09:53:47.461: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C,tsp_info=0x620BF320,

calling_number= called_number=567 redirect_number=):

peer_tag=123dc_switch: fsm_pop()

Jan 6 09:53:47.461: vtsp_do_call_setup_ind

Jan 6 09:53:47.461: vtsp_do_call_setup_ind: Call ID=65677, guid=61FAF610

Jan 6 09:53:47.461: vtsp_do_call_setup_ind: type=0, under_spec=0, name=AB^Lo, id0=3,

id1=0, id2=0, calling=123, called=567

Jan 6 09:53:47.465: dsp_cp_tone_off: [] packet_Len=8 channel_id=8516 packet_id=71

Jan 6 09:53:47.465: dsp_idle_mode: [] packet_Len=8 channel_id=8516 packet_id=68

Jan 6 09:53:47.465: dsp_close_voice_channel: [] packet_Len=8 channel_id=8516

packet_id=75

Jan 6 09:53:47.465: vtsp_timer_stop: 67189073

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp (vdev_info=0x620BF320,

vtsp_cdb=0x621C5F3C)

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:vdev_common

BP TS allocatedat BP_stream0,

BP_Ch27

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 0, BP_ch 27

Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat

stream 7, chan 0,BP_stream 0, BP_ch 27vtsp_open_voice_and_set_params

Jan 6 09:53:47.465: dsp_close_voice_channel: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=75

Jan 6 09:53:47.465: dsp_open_voice_channel_20: [0:1 (52)]

packet_Len=16 channel_id=8516

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=1 serial_port=1

Jan 6 09:53:47.465: dsp_encap_config_20: [0:1 (52)] packet_Len=24

channel_id=8516

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 09:53:47.465: dsp_set_playout: [0:1 (52)] packet_Len=18 channel_id=8516

packet_id=76 mode=1 initial=60 min=4 max=200  fax_nom=300

Jan& 6 09:53:47.465: dsp_echo_canceller_control: [0:1 (52)] packet_Len=10

channel_id=8516

packet_id=66 flags=0x0

Jan 6 09:53:47.465: dsp_set_gains: [0:1 (52)] packet_Len=12 channel_id=8516

packet_id=91 in_gain=0 out_gain=0

Jan 6 09:53:47.465: dsp_vad_enable: [0:1 (52)] packet_Len=10 channel_id=8516

packet_id=78 thresh=-38act_proceeding

Jan 6 09:53:47.469: csm_vtsp_call_proceeding:DST_tdm_chnl call. BP TS

allocatedstream 7,

chan 0,BP_stream 0, BP_ch 27act_alert

Jan 6 09:53:47.493: vtsp_ring_noan_timer_start: 67189076

Jan 6 09:53:47.493: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)

act_bridge act_caps_ind

Jan 6 09:53:47.737: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20,

FaxRate 2, FaxBytes 20 SignalType 0

DtmfRelay 1, Modem 1act_caps_ack

Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=68

Jan 6 09:53:47.737: act_caps_ack: codec = 15, ret = 1

Jan 6 09:53:47.737: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=71

Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=68

Jan 6 09:53:47.737: dsp_encap_config_20: [0:1 (52)] packet_Len=24 channel_id=8516

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 6 09:53:47.737: dsp_voice_mode: [0:1 (52)] packet_Len=24 channel_id=8516

packet_id=73 coding_type=20 voice_field_size= 20 VAD_flag=1 echo_length=64

comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect

Jan 6 09:53:49.461: vtsp_ring_noan_timer_stop: 67189273

Jan 6 09:53:49.461: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516

packet_id=71

Jan 6 09:53:49.461: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C,

voice_vdev=0x620BF320)

Jan 6 09:53:49.461: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK

at slot 2, port 15

Jan 6 09:53:49.617: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):  EVENT_CHANNEL_CONNECTED

at slot 2 and port 15

Jan 6 09:53:49.617: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED

at slot 2, port 15

Jan 6 09:53:49.621: from NEAT(0): (0/2): TX ANSWERED(ABCD=0101)

eefje#

eefje#

R2 Digital Compelled ANI: Incoming Call to 567

In order to understand this debug output better, refer to E1 R2 Signaling Theory.

eefje#debug csm voice

Voice Call Switching Module debugging is on

eefje#debug cas

Channel Associated Signaling debugging is on

Jan 7 10:00:02.907: from NEAT(0): debug-cas is on

Jan 7 10:00:02.907: from NEAT(0): special debug-cas is offg vtsp all

Voice telephony call control all debugging is on

eefje#

eefje#

Jan 7 10:00:23.883: from NEAT(0): (0/8): Rx SEIZURE (ABCD=0001)

Jan 7 10:00:23.927: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:23.927: VDEV_ALLOCATE: 1/2 is allocated

Jan 7 10:00:23.927: csm_vtsp_init_tdm (voice_vdev=0x61F19688)

Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 1,

dspm 3, dsp 4,

dsp_channel 1

Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5,

channel 13,

bank 0, BP_channel 15, BP_stream 255

Jan 7 10:00:23.927: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0007):

EVENT_CALL_DIAL_IN at slot 1

and port 60

Jan 7 10:00:23.927: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 1, port 60

Jan 7 10:00:23.927: csm_vtsp_start_digit_collect (voice_vdev=0x61F19688)

Jan 7 10:00:23.927:  Enter csm_connect_pri_vdev function

Jan 7 10:00:23.927: csm_connect_pri_vdev:tdm_allocate_BP_Ts() call. BP

TS allocated at BP_stream0, BP_Ch8,vdev_common 0x6205E5F8

Jan 7 10:00:23.927: to NEAT:(cid0007) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan8

Jan 7 10:00:23.927: vtsp_do_call_setup_ind

Jan 7 10:00:23.927: vtsp_do_call_setup_ind: Call ID=65579, guid=62031A88

Jan 7 10:00:23.927: vtsp_do_call_setup_ind: type=0, under_spec=0,

name=, id0=0, id1=0,id2=0, calling=, called=

Jan 7 10:00:23.927: vtsp_do_call_setup_ind: redirect DN =  reason =

0vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table)

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp (vdev_info=0x61F19688,

vtsp_cdb=0x61B5BFF8)

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:vdev_common

BP TS allocatedat BP_stream0,

BP_Ch8

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream

5, chan 13,BP_stream 255, BP_ch 15

Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream

5, chan 13,BP_stream 0, BP_ch 8

Jan 7 10:00:23.927: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK

(DNIS=, ANI=) at slot 1, port 60

Jan 7 10:00:23.931: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_IDLE

R2 Got Event R2_START

Jan 7 10:00:24.027: CSM_RX_CAS_EVENT_FROM_NEAT:(0007):  EVENT_START_RX_TONE

at slot 1 and port 60

Jan 7 10:00:24.027: from NEAT(0): (0/8): TX SEIZURE_ACK

(ABCD=1101)dc_init_dsp

vtsp_open_voice_and_set_params

Jan 7 10:00:24.151: dsp_close_voice_channel: [0:1:8] packet_Len=8 channel_id=4929

packet_id=75

Jan 7 10:00:24.151: dsp_open_voice_channel_20: [0:1:8] packet_Len=16

channel_id=4929

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=0 serial_port=0

Jan 7 10:00:24.151: dsp_encap_config_20: [0:1:8] packet_Len=24 channel_id=4929

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0

Jan 7 10:00:24.151: dsp_set_playout: [0:1:8] packet_Len=18 channel_id=4929

packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 7 10:00:24.151: dsp_echo_canceller_control: [0:1:8]

packet_Len=10 channel_id=4929

packet_id=66 flags=0x0

Jan 7 10:00:24.151: dsp_set_gains: [0:1:8] packet_Len=12

channel_id=4929 packet_id=91

in_gain=0 out_gain=0

Jan 7 10:00:24.151: dsp_vad_enable: [0:1:8] packet_Len=10

channel_id=4929 packet_id=78

thresh=-38

Jan 7 10:00:24.151: dsp_voice_mode: [0:1:8] packet_Len=24

channel_id=4929 packet_id=73

coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64

comfort_noise=1

inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode

(VTSP_TONE_R2_MF_FORWARD_MODE)

Jan 7 10:00:24.151: dsp_dtmf_mode: [0:1:8] packet_Len=10 channel_id=4929

packet_id=65dtmf_or_mf=1

!--- Digit 5 is sent: Forward Signal Group I-5 (First DNIS digit).

Jan 7 10:00:24.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=5,

rtp_timestamp=0x04030000 dc_digit_up

Jan 7 10:00:24.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received digit (5)

Jan 7 10:00:24.203: CSM voice (1/60): Rcvd Digit detected(5)

Jan 7 10:00:24.203: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_PRE_CALLERID R2

Got Event 5

!--- Send Backward Signal Group A-5 (caller category request).

Jan 7 10:00:24.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.203:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.303: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=5,

duration=30dc_digit

Jan 7 10:00:24.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (5)

Jan 7 10:00:24.303: CSM voice (1/60): Rcvd Digit detected(5)

Jan 7 10:00:24.303: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:24.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929

packet_id=90 string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.303:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Caller Category Forward Signal Group II-1 is sent.

Jan 7 10:00:24.403: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:24.403: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received

digit (1)

Jan 7 10:00:24.403: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.403: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2

Got Event 1

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.403: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.403: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.403:    digit=, components=2, freq_of_first=1020, freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.503: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,

duration=30dc_digit

Jan 7 10:00:24.503: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1)

Jan 7 10:00:24.503: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.503: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:24.503: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.503: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.503:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- First ANI digit is sent: Forward Signal Group I-1.

Jan  7 10:00:24.603: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=1, rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:24.603: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (1)

Jan 7 10:00:24.603: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.603: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 1

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.603: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.603: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.603:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.703: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,

duration=30dc_digit

Jan 7 10:00:24.703: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1)

Jan 7 10:00:24.703: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:24.703: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:24.703: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.703: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.703:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Second ANI digit is sent: Forward Signal Group I-2.

Jan 7 10:00:24.803: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN:digit=2,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:24.803: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (2)

Jan 7 10:00:24.803: CSM voice (1/60): Rcvd Digit detected(2)

Jan 7 10:00:24.803: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 2

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:24.803: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:24.803: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:24.803:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:24.903: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=2,

duration=30dc_digit

Jan 7 10:00:24.903: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (2)

Jan 7 10:00:24.903: CSM voice (1/60): Rcvd Digit detected(2)

Jan 7 10:00:24.903: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID

R2 Got Event R2_TONE_OFF

Jan 7 10:00:24.903: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:24.903: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:24.903:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Third ANI digit is sent: Forward Signal Group I-3.

Jan 7 10:00:25.003: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=3,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.003: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (3)

Jan 7 10:00:25.003: CSM voice (1/60): Rcvd Digit detected(3)

Jan 7 10:00:25.003: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 3

!--- Send Backward Signal Group A-5 (Caller ID request).

Jan 7 10:00:25.003: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5

Jan 7 10:00:25.003: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=5 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.003:    digit=, components=2, freq_of_first=1020,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.103: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=3,

duration=30dc_digit

Jan 7 10:00:25.103: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (3)

Jan 7 10:00:25.103: CSM voice (1/60): Rcvd Digit detected(3)

Jan 7 10:00:25.103: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.103: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.103: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.103:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Digit 15 is sent: Forward Signal Group I-15 (end of ANI digit).

Jan 7 10:00:25.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:

digit=15,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (*)

Jan 7 10:00:25.203: CSM voice (1/60): Rcvd Digit detected(*)

Jan 7 10:00:25.203: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CALLERID R2

Got Event 15

!--- Send Backward Signal Group A-1 (next DNIS digit).

Jan 7 10:00:25.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=1 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.203:    digit=, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.303: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_OFF: digit=15,

duration=30dc_digit

Jan 7 10:00:25.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (*)

Jan 7 10:00:25.303: CSM voice (1/60): Rcvd Digit detected(*)

Jan 7 10:00:25.303: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929

packet_id=90 string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.303:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Second DNIS digit is sent: Forward Signal Group I-6.

Jan  7 10:00:25.391: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=6,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.391: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (6)

Jan 7 10:00:25.391: CSM voice (1/60): Rcvd Digit detected(6)

Jan 7 10:00:25.391: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS

R2 Got Event 6

!--- Send Backward Signal Group A-1.

Jan 7 10:00:25.391: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=56dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.391: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=1 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.391:    digit=, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.491: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=6,

duration=30dc_digit

Jan 7 10:00:25.491: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (6)

Jan 7 10:00:25.491: CSM voice (1/60): Rcvd Digit detected(6)

Jan 7 10:00:25.491: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.491: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=56dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.491: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.491:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Third DNIS digit is sent: Forward Signal Group I-7.

Jan 7 10:00:25.583: vtsp_process_dsp_message:

MSG_TX_DTMF_DIGIT_BEGIN: digit=7,

rtp_timestamp=0x001E0010 dc_digit_up

Jan 7 10:00:25.583: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (7)

Jan 7 10:00:25.583: CSM voice (1/60): Rcvd Digit detected(7)

Jan 7 10:00:25.583: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event 7

!--- Send Backward Signal Group A-1.

Jan 7 10:00:25.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1

Jan 7 10:00:25.583: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=1 digits=1, time_on=65435, time_off=30

Jan 7 10:00:25.583:    digit=, components=2, freq_of_first=1020,

freq_of_second=1140,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:25.683: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7,

duration=30dc_digit

Jan 7 10:00:25.683: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8)

received digit (7)

Jan 7 10:00:25.683: CSM voice (1/60): Rcvd Digit detected(7)

Jan 7 10:00:25.683: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_OFF

Jan 7 10:00:25.683: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:25.683: dsp_dtmf_dialing: [0:1:8] packet_Len=24

channel_id=4929 packet_id=90

string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:25.683:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1

Jan 7 10:00:25.835: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done()

!--- Timeout is 3 seconds.

Jan 7 10:00:28.583: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_COLLECT_DNIS R2

Got Event R2_TONE_TIMER

!--- Send Backward Signal Group A-3: address-complete, changeover !--- to reception of group-B signal.

Jan 7 10:00:28.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3#

Jan 7 10:00:28.583: dsp_dtmf_dialing: [0:1:8] packet_Len=36

channel_id=4929 packet_id=90

string=3# digits=2, time_on=150, time_off=30

Jan 7 10:00:28.583:    digit=, components=2, freq_of_first=1020,

freq_of_second=900,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:28.583:    digit=, components=2, freq_of_first=0, freq_of_second=0,

amp_of_first=1, amp_of_second=1

!--- Forward Signal Group II-1 is sent: subscriber without priority.

Jan 7 10:00:28.831: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,

rtp_timestamp=0x001E0003 dc_digit_up

Jan 7 10:00:28.831: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (1)

Jan 7 10:00:28.831: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:28.831: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_CATEGORY R2

Got Event 1

Jan 7 10:00:28.831: CSM_PROC_IC1_COLLECT_ADDR_INFO:

CSM_EVENT_ADDR_INFO_COLLECTED

(DNIS=567, ANI=123) at slot 1, port 60

Jan 7 10:00:28.831: vtsp_tsp_call_accept_check (sdb=0x61DADEE0,

calling_number=123

called_number=567): peer_tag=0

Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate

a non-idle modem

Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate

a non-idle modem

Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device

Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate

a non-idle modem

Jan 7 10:00:28.835: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK

at slot 1,

port 60

Jan 7 10:00:28.835: vtsp_IC_switch : (voice_vdev= 0x61F19688)

Jan 7 10:00:28.835: vtsp_tsp_call_switch_ind (cdb=0x61B5BFF8,

tsp_info=0x61F19688,

calling_number=123 called_number=567 redirect_number=):

peer_tag=123dc_switch: fsm_pop()

Jan 7 10:00:28.835: vtsp_do_call_setup_ind

Jan 7 10:00:28.835: vtsp_do_call_setup_ind: Call ID=65581,

guid=62031A88

Jan 7 10:00:28.835: vtsp_do_call_setup_ind: type=0, under_spec=0,

name=b`, id0=9,

id1=0, id2=0, calling=123, called=567

Jan 7 10:00:28.835: dsp_cp_tone_off: [] packet_Len=8 channel_id=4929

packet_id=71

Jan 7 10:00:28.835: dsp_idle_mode: [] packet_Len=8 channel_id=4929

packet_id=68

Jan 7 10:00:28.835: dsp_close_voice_channel: [] packet_Len=8

channel_id=4929 packet_id=75

Jan 7 10:00:28.835: vtsp_timer_stop: 7063006

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp (vdev_info=0x61F19688,

vtsp_cdb=0x61B5BFF8)

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:vdev_common BP TS

allocatedat BP_stream0,

BP_Ch8

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 8

Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call.

BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch

8vtsp_open_voice_and_set_params

Jan 7 10:00:28.839: dsp_close_voice_channel: [0:1 (17)]

packet_Len=8 channel_id=4929

packet_id=75

Jan 7 10:00:28.839: dsp_open_voice_channel_20: [0:1 (17)] packet_Len=16

channel_id=4929

packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0

time_slot=0 serial_port=0

Jan 7 10:00:28.839: dsp_encap_config_20: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0t_vpxcc=0x0

r_vpxcc=0x0

Jan 7 10:00:28.839: dsp_set_playout: [0:1 (17)] packet_Len=18

channel_id=4929 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300

Jan 7 10:00:28.839: dsp_echo_canceller_control: [0:1 (17)]

packet_Len=10 channel_id=4929

packet_id=66 flags=0x0

Jan 7 10:00:28.839: dsp_set_gains: [0:1 (17)] packet_Len=12

channel_id=4929 packet_id=91

in_gain=0 out_gain=0

Jan 7 10:00:28.839: dsp_vad_enable: [0:1 (17)] packet_Len=10

channel_id=4929 packet_id=78

thresh=-38act_proceeding

Jan 7 10:00:28.839: csm_vtsp_call_proceeding:DST_tdm_chnl call.

BP TS allocatedstream 5,

chan 13,BP_stream 0, BP_ch 8act_alert

Jan 7 10:00:28.867: vtsp_ring_noan_timer_start: 7063009

Jan 7 10:00:28.867: csm_vtsp_call_alert (vtsp_cdb=0x61B5BFF8)

Jan 7 10:00:28.867:  csm_vtsp_call_alert: CSM_EVENT_ALERTING_RECEIVED

Jan 7 10:00:28.867: CSM_IC5_WAIT_FOR_SWITCH_OVER:  at slot 1, port 60

Jan 7 10:00:28.867: CSM_EVENT_ALERTING_RECEIVED:

Jan 7 10:00:28.867:  calling alerting_start_event

!--- Note: For modems, Backward Signal !--- Group B-6 (subscriber's line free, charge) !--- is sent immediately. !--- For voice, it is delayed until alerting is received. !--- Notice that "R2_REJECT" is printed instead of R2_ALERTING. !--- This printing issue is solved in Cisco IOS Software Release 12.1T.

Jan 7 10:00:28.867: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE:R2_IN_IDLE R2

Got Event R2_REJECT

Jan 7 10:00:28.867:  R2_ALERTING: r2_comp_idle

Jan 7 10:00:28.867: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567act_bridge

Jan 7 10:00:28.867: dsp_voice_mode: [0:1 (17)] packet_Len=24

channel_id=4929 packet_id=73

coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64

comfort_noise=1

inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode

(VTSP_TONE_R2_MF_FORWARD_MODE)

!--- Answer signal (B-6) is sent after alerting is received. !--- Send Backward Signal Group B6 signal (Subscriber's line free, charge).

Jan 7 10:00:28.871: dsp_dtmf_mode: [0:1 (17)] packet_Len=10

channel_id=4929 packet_id=65

dtmf_or_mf=1vtsp_r2_dial vtsp_r2_dial(): fsm_push(vtsp_r2_state_table)

dsp_dtmf_dialing(): dial_string = 6

Jan 7 10:00:28.871: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=90 string=6 digits=1, time_on=65435, time_off=30

Jan 7 10:00:28.871:    digit=, components=2, freq_of_first=900,

freq_of_second=780,

amp_of_first=8192, amp_of_second=8192

Jan 7 10:00:28.923: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1,

rtp_timestamp=0x001E0006 dc_digit_up

Jan 7 10:00:28.923: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)

received digit (1)

Jan 7 10:00:28.923: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:28.923: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_COMPLETE

R2 Got Event 1

Jan 7 10:00:28.971: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1,

duration=30dc_digit

Jan 7 10:00:28.971: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8)

received digit (1)

Jan 7 10:00:28.971: CSM voice (1/60): Rcvd Digit detected(1)

Jan 7 10:00:28.971: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_COMPLETE R2

Got Event R2_TONE_OFF

Jan 7 10:00:28.971: vtsp_r2_generate_digits: vdev_common=0x6205E5F8,

string=567dc_dial()

vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = #

Jan 7 10:00:28.971: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=90 string=# digits=1, time_on=150, time_off=30

Jan 7 10:00:28.975:    digit=, components=2, freq_of_first=0,

freq_of_second=0,

amp_of_first=1, amp_of_second=1ds_dialing_defaultds_dialing_default

Jan 7 10:00:29.127: vtsp_process_dsp_message:

MSG_TX_DIALING_DONEdc_dialing_done()

Jan 7 10:00:29.971: R2 Incoming Voice(1/60): DSX (E1 0:8):

STATE: R2_IN_WAIT_GUARD R2

Got Event R2_TONE_TIMER

Jan 7 10:00:29.971:  R2_IN_IDLE:2 r2_in_connect called

Jan 7 10:00:29.971: R2_IN_CONNECT: call end dial

Jan 7 10:00:29.971:  pop the dial state machine

Jan 7 10:00:29.971: vtsp_r2_end_dial: vdev_common=0x6205E5F8,

string=567ds_end_dial():

fsm_pop() act_caps_ind

Jan 7 10:00:29.971: act_caps_ind:Encap 1, Vad 2, Codec 0x4,

CodecBytes 20, FaxRate 2,

FaxBytes 20 SignalType 0 DtmfRelay 1, Modem 1act_caps_ack

Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=68

Jan 7 10:00:29.971: act_caps_ack: codec = 15, ret = 1

Jan 7 10:00:29.971: dsp_cp_tone_off: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=71

Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=68

Jan 7 10:00:29.971: dsp_encap_config_20: [0:1 (17)] packet_Len=24

channel_id=4929

packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0

r_vpxcc=0x0

Jan 7 10:00:29.971: dsp_voice_mode: [0:1 (17)] packet_Len=24

channel_id=4929 packet_id=73

coding_type=19 voice_field_size=20 VAD_flag=1 echo_length=64

comfort_noise=1

inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect

Jan 7 10:00:30.255: vtsp_ring_noan_timer_stop: 7063148

Jan 7 10:00:30.255: dsp_cp_tone_off: [0:1 (17)] packet_Len=8

channel_id=4929 packet_id=71

Jan 7 10:00:30.255: csm_vtsp_call_connect (vtsp_cdb=0x61B5BFF8,

voice_vdev=0x61F19688)

Jan 7 10:00:30.255: CSM_IC5_WAIT_FOR_SWITCH_OVER:

CSM_EVENT_MODEM_OFFHOOK at slot 1,

port 60

Jan 7 10:00:30.607: CSM_RX_CAS_EVENT_FROM_NEAT:(0007):

EVENT_CHANNEL_CONNECTED at slot 1

and port 60

Jan 7 10:00:30.607: CSM_PROC_IC6_WAIT_FOR_CONNECT:

CSM_EVENT_DSX0_CONNECTED at slot 1,

port 60

Jan 7 10:00:30.607: from NEAT(0): (0/8): TX ANSWERED (ABCD=0101)

eefje#

Related Information

- E1 R2 Signaling for Voice over IP on the Cisco AS5300 Access Server

- E1 R2 Signaling for the Cisco 3620 and 3640 Series Routers

- E1 R2 Customization with the cas-custom Command

- E1 R2 and Channel-Associated Signaling Configuration

- E1 R2 Signaling for the Cisco AS5300 and Cisco AS5200 Access Servers

- Voice Technology Support

- Voice and Unified Communications Product Support

- Troubleshooting Cisco IP Telephony

- Technical Support & Documentation - Cisco Systems