1 |
User-Name |
Indicates the name of the user being authenticated by the RADIUS server. |
2 |
User-Password |
Indicates the user's password or the user's input following an Access-Challenge. Passwords longer than 16 characters are encrypted using RFC 2865 specifications. |
3 |
CHAP-Password |
Indicates the response value provided by a PPP Challenge-Handshake Authentication Protocol (CHAP) user in response to an Access-Challenge. |
4 |
NAS-IP Address |
Specifies the IP address of the network access server that is requesting authentication. The default value is 0.0.0.0/0. |
5 |
NAS-Port |
Indicates the physical port number of the network access server that is authenticating the user. The NAS-Port value (32 bits) consists of one or two 16-bit values (depending on the setting of the radius-server extended-portnames command). Each 16-bit number should be viewed as a 5-digit decimal integer for interpretation as follows: For asynchronous terminal lines, async network interfaces, and virtual async interfaces, the value is 00ttt, where ttt is the line number or async interface unit number. For ordinary synchronous network interface, the value is 10xxx. For channels on a primary rate ISDN interface, the value is 2ppcc. For channels on a basic rate ISDN interface, the value is 3bb0c. For other types of interfaces, the value is 6nnss. |
6 |
Service-Type |
Indicates the type of service requested or the type of service to be provided.
Framed for known PPP or SLIP connection. Administrative-user for enable command.
Login--Make a connection. Framed--Start SLIP or PPP. Administrative User--Start an EXEC or enable ok. Exec User--Start an EXEC session. Service type is indicated by a particular numeric value as follows:
- 1: Login
- 2: Framed
- 3: Callback-Login
- 4: Callback-Framed
- 5: Outbound
- 6: Administrative
- 7: NAS-Prompt
- 8: Authenticate Only
- 9: Callback-NAS-Prompt
|
7 |
Framed-Protocol |
Indicates the framing to be used for framed access. No other framing is allowed. Framing is indicated by a numeric value as follows:
- 1: PPP
- 2: SLIP
- 3: ARA
- 4: Gandalf-proprietary single-link/multilink protocol
- 5: Xylogics-proprietary IPX/SLIP
|
8 |
Framed-IP-Address |
Indicates the IP address to be configured for the user, by sending the IP address of a user to the RADIUS server in the access-request. To enable this command, use the radius-server attribute 8 include-in-access-req command in global configuration mode. |
9 |
Framed-IP-Netmask |
Indicates the IP netmask to be configured for the user when the user is a router to a network. This attribute value results in a static route being added for Framed-IP-Address with the mask specified. |
10 |
Framed-Routing |
Indicates the routing method for the user when the user is a router to a network. Only "None" and "Send and Listen" values are supported for this attribute. Routing method is indicated by a numeric value as follows:
- 0: None
- 1: Send routing packets
- 2: Listen for routing packets
- 3: Send routing packets and listen for routing packets
|
11 |
Filter-Id |
Indicates the name of the filter list for the user and is formatted as follows: %d, %d.in, or %d.out. This attribute is associated with the most recent service-type command. For login and EXEC, use %d or %d.out as the line access list value from 0 to 199. For Framed service, use %d or %d.out as interface output access list, and %d.in for input access list. The numbers are self-encoding to the protocol to which they refer. |
12 |
Framed-MTU |
Indicates the maximum transmission unit (MTU) that can be configured for the user when the MTU is not negotiated by PPP or some other means. |
13 |
Framed-Compression |
Indicates a compression protocol used for the link. This attribute results in a "/compress" being added to the PPP or SLIP autocommand generated during EXEC authorization. Not currently implemented for non-EXEC authorization. Compression protocol is indicated by a numeric value as follows:
- 0: None
- 1: VJ-TCP/IP header compression
- 2: IPX header compression
|
14 |
Login-IP-Host |
Indicates the host to which the user will connect when the Login-Service attribute is included. (This begins immediately after login.) |
15 |
Login-Service |
Indicates the service that should be used to connect the user to the login host. Service is indicated by a numeric value as follows:
- 0: Telnet
- 1: Rlogin
- 2: TCP-Clear
- 3: PortMaster
- 4: LAT
|
16 |
Login-TCP-Port |
Defines the TCP port with which the user is to be connected when the Login-Service attribute is also present. |
18 |
Reply-Message |
Indicates text that might be displayed to the user via the RADIUS server. You can include this attribute in user files; however, you cannot exceed a maximum of 16 Replyp-Message entries per profile. |
19 |
Callback-Number |
Defines a dialing string to be used for callback. |
20 |
Callback-ID |
Defines the name (consisting of one or more octets) of a place to be called, to be interpreted by the network access server. |
22 |
Framed-Route |
Provides routing information to be configured for the user on this network access server. The RADIUS RFC format (net/bits [router [metric]]) and the old style dotted mask (net mask [router [metric]]) are supported. If the router field is omitted or 0, the peer IP address is used. Metrics are currently ignored. This attribute is access-request packets. |
23 |
Framed-IPX-Network |
Defines the IPX network number configured for the user. |
24 |
State |
Allows state information to be maintained between the network access server and the RADIUS server. This attribute is applicable only to CHAP challenges. |
25 |
Class |
(Accounting) Arbitrary value that the network access server includes in all accounting packets for this user if supplied by the RADIUS server. |
26 |
Vendor-Specific |
Allows vendors to support their own extended attributes not suitable for general use. The Cisco RADIUS implementation supports one vendor-specific option using the format recommended in the specification. Cisco's vendor-ID is 9, and the supported option has vendor-type 1, which is named "cisco-avpair." The value is a string of the format:
protocol : attribute sep value
"Protocol" is a value of the Cisco "protocol" attribute for a particular type of authorization. "Attribute" and "value" are an appropriate AV pair defined in the Cisco TACACS+ specification, and "sep" is "=" for mandatory attributes and "*" for optional attributes. This allows the full set of features available for TACACS+ authorization to also be used for RADIUS. For example:
cisco-avpair= "ip:addr-pool=first"
cisco-avpair= "shell:priv-lvl=15"
The first example causes Cisco's "multiple named ip address pools" feature to be activated during IP authorization (during PPP's IPCP address assignment). The second example causes a user logging in from a network access server to have immediate access to EXEC commands. Table 1 lists supported vendor-specific RADIUS attributes (IETF attribute 26). The "TACACS+ Attribute-Value Pairs" module provides a complete list of supported TACACS+ attribute-value (AV) pairs that can be used with IETF attribute 26. ( RFC 2865 ) |
27 |
Session-Timeout |
Sets the maximum number of seconds of service to be provided to the user before the session terminates. This attribute value becomes the per-user "absolute timeout." |
28 |
Idle-Timeout |
Sets the maximum number of consecutive seconds of idle connection allowed to the user before the session terminates. This attribute value becomes the per-user "session-timeout." |
29 |
Termination-Action |
Termination is indicated by a numeric value as follows:
- 0: Default
- 1: RADIUS request
|
30 |
Called-Station-Id |
(Accounting) Allows the network access server to send the telephone number the user called as part of the Access-Request packet (using Dialed Number Identification Service [DNIS] or similar technology). This attribute is only supported on ISDN, and modem calls on the Cisco AS5200 if used with PRI. |
31 |
Calling-Station-Id |
(Accounting) Allows the network access server to send the telephone number the call came from as part of the Access-Request packet (using Automatic Number Identification or similar technology). This attribute has the same value as "remote-addr" from TACACS+. This attribute is only supported on ISDN, and modem calls on the Cisco AS5200 if used with PRI. |
32 |
NAS-Identifier |
String identifying the network access server originating the Access-Request. Use the radius-server attribute 32 include-in-access-req global configuration command to send RADIUS attribute 32 in an Access-Request or Accounting-Request. By default, the FQDN is sent in the attribute when the format is not specified. |
33 |
Proxy-State |
Attribute that can be sent by a proxy server to another server when forwarding Access-Requests; this must be returned unmodified in the Access-Accept, Access-Reject or Access-Challenge and removed by the proxy server before sending the response to the network access server. |
34 |
Login-LAT-Service |
Indicates the system with which the user is to be connected by LAT. This attribute is only available in the EXEC mode. |
35 |
Login-LAT-Node |
Indicates the node with which the user is to be automatically connected by LAT. |
36 |
Login-LAT-Group |
Identifies the LAT group codes that this user is authorized to use. |
37 |
Framed-AppleTalk-Link |
Indicates the AppleTalk network number that should be used for serial links to the user, which is another AppleTalk router. |
38 |
Framed-AppleTalk- Network |
Indicates the AppleTalk network number that the network access server uses to allocate an AppleTalk node for the user. |
39 |
Framed-AppleTalk-Zone |
Indicates the AppleTalk Default Zone to be used for this user. |
40 |
Acct-Status-Type |
(Accounting) Indicates whether this Accounting-Request marks the beginning of the user service (start) or the end (stop). |
41 |
Acct-Delay-Time |
(Accounting) Indicates how many seconds the client has been trying to send a particular record. |
42 |
Acct-Input-Octets |
(Accounting) Indicates how many octets have been received from the port over the course of this service being provided. |
43 |
Acct-Output-Octets |
(Accounting) Indicates how many octets have been sent to the port in the course of delivering this service. |
44 |
Acct-Session-Id |
(Accounting) A unique accounting identifier that makes it easy to match start and stop records in a log file. Acct-Session ID numbers restart at 1 each time the router is power cycled or the software is reloaded. To send this attribute in access-request packets, use the radius-server attribute 44 include-in-access-req command in global configuration mode. |
45 |
Acct-Authentic |
(Accounting) Indicates how the user was authenticated, whether by RADIUS, the network access server itself, or another remote authentication protocol. This attribute is set to "radius" for users authenticated by RADIUS; "remote" for TACACS+ and Kerberos; or "local" for local, enable, line, and if-needed methods. For all other methods, the attribute is omitted. |
46 |
Acct-Session-Time |
(Accounting) Indicates how long (in seconds) the user has received service. |
47 |
Acct-Input-Packets |
(Accounting) Indicates how many packets have been received from the port over the course of this service being provided to a framed user. |
48 |
Acct-Output-Packets |
(Accounting) Indicates how many packets have been sent to the port in the course of delivering this service to a framed user. |
49 |
Acct-Terminate-Cause |
(Accounting) Reports details on why the connection was terminated. Termination causes are indicated by a numeric value as follows:
- User request
- Lost carrier
- Lost service
- Idle timeout
- Session timeout
- Admin reset
- Admin reboot
- Port error
- NAS error
- NAS request
- NAS reboot
- Port unneeded
- Port pre-empted
- Port suspended
- Service unavailable
- Callback
- User error
- Host request
Note |
For attribute 49, Cisco IOS supports values 1 to 6, 9, 12, and 15 to 18. |
|
50 |
Acct-Multi-Session-Id |
(Accounting) A unique accounting identifier used to link multiple related sessions in a log file. Each linked session in a multilink session has a unique Acct-Session-Id value, but shares the same Acct-Multi-Session-Id. |
51 |
Acct-Link-Count |
(Accounting) Indicates the number of links known in a given multilink session at the time an accounting record is generated. The network access server can include this attribute in any accounting request that might have multiple links. |
52 |
Acct-Input-Gigawords |
Indicates how many times the Acct-Input-Octets counter has wrapped around 2^32 over the course of the provided service. |
53 |
Acct-Output-Gigawords |
Indicates how many times the Acct-Output-Octets counter has wrapped around 2^32 while delivering service. |
55 |
Event-Timestamp |
Records the time that the event occurred on the NAS; the timestamp sent in attribute 55 is in seconds since January 1, 1970 00:00 UTC. To send RADIUS attribute 55 in accounting packets, use the radius-server attribute 55 include-in-acct-req command.
Note |
Before the Event-Timestamp attribute can be sent in accounting packets, you must configure the clock on the router. (For information on setting the clock on your router, refer to the Cisco IOS Configuration Fundamentals Configuration Guide , Release 12.4T.) To avoid configuring the clock on the router every time the router is reloaded, you can enable the clock calendar-valid command. See the Cisco IOS Configuration Fundamentals Command Reference for more information on this command. |
|
60 |
CHAP-Challenge |
Contains the Challenge Handshake Authentication Protocol challenge sent by the network access server to a PPP CHAP user. |
61 |
NAS-Port-Type |
Indicates the type of physical port the network access server is using to authenticate the user. Physical ports are indicated by a numeric value as follows:
- 0: Asynchronous
- 1: Synchronous
- 2: ISDN-Synchronous
- 3: ISDN-Asynchronous (V.120)
- 4: ISDN-Asynchronous (V.110)
- 5: Virtual
|
62 |
Port-Limit |
Sets the maximum number of ports provided to the user by the NAS. |
63 |
Login-LAT-Port |
Defines the port with which the user is to be connected by LAT. |
64 |
Tunnel-Type3 |
Indicates the tunneling protocol(s) used. Cisco IOS software supports two possible values for this attribute: L2TP and L2F. If this attribute is not set, L2F is used as a default. |
65 |
Tunnel-Medium-Type1 |
Indicates the transport medium type to use to create a tunnel. This attribute has only one available value for this release: IP. If no value is set for this attribute, IP is used as the default. |
66 |
Tunnel-Client-Endpoint |
Contains the address of the initiator end of the tunnel. It may be included in both Access-Request and Access-Accept packets to indicate the address from which a new tunnel is to be initiated. If the Tunnel-Client-Endpoint attribute is included in an Access-Request packet, the RADIUS server should take the value as a hint; the server is not obligated to honor the hint, however. This attribute should be included in Accounting-Request packets that contain Acct-Status-Type attributes with values of either Start or Stop, in which case it indicates the address from which the tunnel was initiated. This attribute, along with the Tunnel-Server-Endpoint and Acct-Tunnel-Connection-ID attributes, may be used to provide a globally unique means to identify a tunnel for accounting and auditing purposes. An enhancement has been added for the network access server to accept a value of 127.0.0.X for this attribute such that: 127.0.0.0 would indicate that loopback0 IP address is to be used 127.0.0.1 would indicate that loopback1 IP address is to be used ... 127.0.0.X would indicate that loopbackX IP address is to be used for the actual tunnel client endpoint IP address. This enhancement adds scalability across multiple network access servers. |
67 |
Tunnel-Server-Endpoint1 |
Indicates the address of the server end of the tunnel. The format of this attribute varies depending on the value of Tunnel-Medium-Type. Because this release only supports IP as a tunnel medium type, the IP address or the host name of LNS is valid for this attribute. |
68 |
Acct-Tunnel-Connection-ID |
Indicates the identifier assigned to the tunnel session. This attribute should be included in Accounting-Request packets that contain an Acct-Status-Type attribute having the value Start, Stop, or any of the values described above. This attribute, along with the Tunnel-Client-Endpoint and Tunnel-Server-Endpoint attributes, may be used to provide a means to uniquely identify a tunnel session for auditing purposes. |
69 |
Tunnel-Password1 |
Defines the password to be used to authenticate to a remote server. This attribute is converted into different AAA attributes based on the value of Tunnel-Type: AAA_ATTR_l2tp_tunnel_pw (L2TP), AAA_ATTR_nas_password (L2F), and AAA_ATTR_gw_password (L2F). By default, all passwords received are encrypted, which can cause authorization failures when a NAS attempts to decrypt a non-encrypted password. To enable attribute 69 to receive non-encrypted passwords, use the radius-server attribute 69 clearglobal configuration command. |
70 |
ARAP-Password |
Identifies an Access-Request packet containing a Framed-Protocol of ARAP. |
71 |
ARAP-Features |
Includes password information that the NAS should send to the user in an ARAP "feature flags" packet. |
72 |
ARAP-Zone-Access |
Indicates how the ARAP zone list for the user should be used. |
73 |
ARAP-Security |
Identifies the ARAP Security Module to be used in an Access-Challenge packet. |
74 |
ARAP-Security-Data |
Contains the actual security module challenge or response. It can be found in Access-Challenge and Access-Request packets. |
75 |
Password-Retry |
Indicates how many times a user may attempt authentication before being disconnected. |
76 |
Prompt |
Indicates to the NAS whether it should echo the user's response as it is entered or not echo it. (0=no echo, 1=echo) |
77 |
Connect-Info |
Provides additional call information for modem calls. This attribute is generated in start and stop accounting records. |
78 |
Configuration-Token |
Indicates a type of user profile to be used. This attribute should be used in large distributed authentication networks based on proxy. It is sent from a RADIUS Proxy Server to a RADIUS Proxy Client in an Access-Accept; it should not be sent to a NAS. |
79 |
EAP-Message |
Encapsulates Extended Access Protocol (EAP) packets that allow the NAS to authenticate dial-in users via EAP without having to understand the EAP protocol. |
80 |
Message-Authenticator |
Prevents spoofing Access-Requests using CHAP, ARAP, or EAP authentication methods. |
81 |
Tunnel-Private-Group-ID |
Indicates the group ID for a particular tunneled session. |
82 |
Tunnel-Assignment-ID1 |
Indicates to the tunnel initiator the particular tunnel to which a session is assigned. |
83 |
Tunnel-Preference |
Indicates the relative preference assigned to each tunnel. This attribute should be included if more than one set of tunneling attributes is returned by the RADIUS server to the tunnel initiator. |
84 |
ARAP-Challenge-Response |
Contains the response to the challenge of the dial-in client. |
85 |
Acct-Interim-Interval |
Indicates the number of seconds between each interim update in seconds for this specific session. This value can only appear in the Access-Accept message. |
86 |
Acct-Tunnel-Packets-Lost |
Indicates the number of packets lost on a given link. This attribute should be included in Accounting-Request packets that contain an Acct-Status-Type attribute having the value Tunnel-Link-Stop. |
87 |
NAS-Port-ID |
Contains a text string which identifies the port of the NAS that is authenticating the user. |
88 |
Framed-Pool |
Contains the name of an assigned address pool that should be used to assign an address for the user. If a NAS does not support multiple address pools, the NAS should ignore this attribute. |
90 |
Tunnel-Client-Auth-ID |
Specifies the name used by the tunnel initiator (also known as the NAS) when authenticating tunnel setup with the tunnel terminator. Supports L2F and L2TP protocols. |
91 |
Tunnel-Server-Auth-ID |
Specifies the name used by the tunnel terminator (also known as the Home Gateway) when authenticating tunnel setup with the tunnel initiator. Supports L2F and L2TP protocols. |
200 |
IETF-Token-Immediate |
Determines how RADIUS treats passwords received from login-users when their file entry specifies a hand-held security card server. The value for this attribute is indicated by a numeric value as follows:
- 0: No, meaning that the password is ignored.
- 1: Yes, meaning that the password is used for authentication.
|