What's New in Cisco IOS XR Release 7.5.2
Cisco IOS XR Release 7.5.2 is an Extended Maintenance Release of Cisco IOS XR Release 7.5.1 for Cisco NCS 540 Series routers. For more details on the Cisco IOS XR release model and associated support, see Guidelines for Cisco IOS XR Software.
Feature | Description |
---|---|
Hardware |
|
Support for Cisco Network Convergence System 540 Passive Cooled Small Density Routers |
This release introduces these IOS XR-based cell site routers that extend Cisco’s 5G Converged SDN Transport to the edge of the networks as a Cloud Services Router (CSR)/ Network Interface Device (NID)/ Customer Premises Equipment (CPE) with the smallest footprint. The Cisco N540-6Z14S-SYS-D is a cell site router and has the following features:
For more information, see the Cisco Network Convergence System 540 Passive Cooled Small Density Routers Hardware Installation Guide. |
Cisco N540X-16Z8Q2C-D Routers |
This release introducesthe Cisco N540X-16Z8Q2C-D routers to accommodate specific installation requirements. The router has the following hardware features:
For more information, see the Cisco NCS 540 Router Hardware Installation Guide. |
The following features are supported on all the NCS 540 variants.
Feature | Description | ||
---|---|---|---|
System Monitoring |
|||
You can configure the SNMP agent to generate IPv4 and IPv6 SNMP traps when the router triggers a message to the Network Management System (NMS) that a node is going down. Such a message, known as a dying gasp event, is sent when a power failure occurs or the input power source is disconnected. |
|||
Interface and Hardware Component |
|||
You can now configure the VLAN subinterface as a source for traffic mirroring for:
You could configure mirror functionality only at the main interface level in earlier releases. |
|||
Ethernet Link OAM on Physical Interface— (802.3ah) Link Monitoring and Remote Loopback |
Ethernet link OAM operates on a single, physical link and it can be configured to monitor either side or both sides of that link. Ethernet OAM supports:
|
||
L2VPN and Ethernet Services |
|||
This feature helps reduce network congestion and avoid traffic loss by shutting down a port after it reaches the configured number of MAC moves within the specified move interval. You can configure this feature at the bridge-domain level using the mac secure command. This feature is now supported on routers that operate in native and compatibility modes. |
|||
Segment Routing |
|||
SRv6: Ultimate Segment Decapsulation (USD) behavior |
This feature supports the Ultimate Segment Decapsulation (USD) variant on SRv6 endpoint nodes using full-length SIDs. Previously, USD variant was supported on SRv6 endpoint nodes using using Micro SIDs (uSIDs). The USD variant enables interworking with SRv6 underlay headend nodes that push SIDs using H.Encaps (SR Headend Behavior with Encapsulation in an SRv6 Policy) or H.Encaps.Red (H.Encaps with reduced Encapsulation) instead of H.Insert (SR Headend with insertion of an SRv6 Policy) or H.Insert.Red (H.Insert with reduced insertion). The USD variant enables interworking with SRv6 underlay headend nodes that push SIDs using H.Encaps (SR Headend Behavior with Encapsulation in an SRv6 Policy) or H.Encaps.Red (H.Encaps with reduced Encapsulation) instead of H.Insert (SR Headend with insertion of an SRv6 Policy) or H.Insert.Red (H.Insert with reduced insertion). |
||
You can now configure the flexible algorithm to exclude any link belonging to the Shared Risk Link Groups (SRLGs) from the path computation for OSPF. The ability to exclude the at-risk links ensures that the rest of the links in the network remain unaffected. |
|||
Flexible Algorithm Prefix-SID Redistribution for External Route Propagation |
This feature enables the propagation of flexible algorithm prefix-SIDs and their algo-specific metric from other domains into OSPF, and from OSPF to other domains. The show route command has been modified to include additional attributes to indicate the external routes. |
||
BGP-SR multipath ECMP FEC optimization is enhanced to support 32k BGP-LU prefixes (from the earlier 4k BGP-LU prefixes) on multipath with the same outgoing label. This results in the consumption of lesser ECMP FEC resources, thus avoiding out-of-resource (OOR) situations for your router. In earlier releases, all 4k BGP-LU prefixes consumed all the 4k ECMP FEC resources. Use the hw-module fib mpls bgp-sr lsr-optimized command to enable BGP-SR multipath ECMP FEC optimization. |
|||
BGP |
|||
BGP-LU multipath prefix independent convergence (PIC) supports auto protection. Each active path has a backup path, ensuring almost immediate restoration of multicast traffic when a path fails. In earlier releases, path failures led to traffic drops in the absence of auto protection.
|
|||
You can now configure to replace the AS Path in BGP with custom values, based on route policy. While selecting BGP best path, a shorter AS Path makes the selection process simple and flexible. This feature introduces the following command:
|
|||
RIPng |
RIPng (RIP next generation) is a RIPv2 extension that supports IPv6 which is the next-generation Internet Protocol. RIPng provides routing functionalities for an IPv6-based network. RIPng functions as an interior gateway protocol (IGP) in moderate-sized autonomous systems. RIPng uses Bellman-Ford distance-vector algorithm to determine the best route to an IPv6 destination. RIP enhancements for IPv6 include support for IPv6 addresses and prefixes; and the use of the all-RIP-devices multicast group address FF02::9 as the destination address for RIP update messages. |
||
Programmability |
|||
New Unified Models |
Unified models are CLI-based YANG models that are designed to replace the native schema-based models. This releaes introduces new unified models. You can access the new unified models from the Github repository. |
||
Modular QoS |
|||
Setting MPLS Experimental Bits on Inner MPLS Headers to Classify Traffic |
For MPLS over GRE scenarios that tunnel MPLS traffic over non-MPLS networks across CE devices, you can now perform QoS classification for specific traffic or applications by setting MPLS EXP bit field values in the inner MPLS header. In earlier releases, you could perform QoS classification only in the outer GRE IP header using DiffServ Code Point (DSCP) or IP precedence bits that helped you achieve the required line rate minus the granularity. This feature introduces the hw-module profile qos gre-exp-classification-enable command. |
||
Multicast |
|||
Flexible Algorithm is now available for the following profiles:
|
The following features are supported on N540-24Q8L2DD-SYS variant.
Feature | Description |
---|---|
System Setup and Software Installation |
|
GISO is a customized image with the standard functional components and additional configuration files. This feature extracts the IOS XR configuration file in GISO and automates the updating of configuration files when the router is reloaded with the new GISO. This feature introduces iso-config [ignore | replace] keywords to the install replace and install package replace commands. |
|
This feature enables an easy one-step, no prompt upgrade, or downgrade, based on GISO. This removes the dependency on having to manually install the bridging bug fix RPMs before performing an upgrade or a downgrade. |
The following features are supported on N540-6Z14S-SYS-D variant.
Feature | Description |
---|---|
Network Synchronization |
|
In this release, the following Cisco NCS 540 router variant supports Synchronous Ethernet with ESMC and SSM:
SyncE provides synchronization signals transmitted over the Ethernet physical layer to downstream devices, while the Synchronization Status Message (SSM) indicates the quality level of the transmitting clock to the neighboring nodes, informing the nodes about the level of the network's reliability. Ethernet Synchronization Message Channel (ESMC) is the logical channel that uses an Ethernet PDU (protocol data unit) to exchange SSM information over the SyncE link. |
|
In this release, the following Cisco NCS 540 router variant supports Synchronous Ethernet with ESMC and SSM:
PTP Profiles are specific selections of PTP configurations that allow organizations to achieve a performance that meets the requirement of a particular application. You can configure different PTP profiles for different applications, such as audio and media. PTP profiles ensure the application components stay in sync across multiple devices. |
|
System Monitoring |
|
You can configure the SNMP agent to generate IPv4 and IPv6 SNMP traps when the router triggers a message to the Network Management System (NMS) that a node is going down. Such a message, known as a dying gasp event, is sent when a power failure occurs or the input power source is disconnected. |
The following features are supported on N540X-6Z18G-SYS-A/D, N540X-8Z16G-SYS-A/D, and N540X-4Z14G2Q-A/D variants.
Feature | Description |
---|---|
Modular QoS |
|
In this release, the Cisco Network Convergence System 540 Small Density Routers support the ability to match class maps to IPv4 and IPv6 destination addresses on Layer 2 networks. This feature provides you with an extra level of classification for aggregated customer traffic at your ingress, thus giving you granular control on traffic flows. |
The following features are supported on N540-ACC-SYS, N540X-ACC-SYS, N540-24Z8Q2C-SYS, N540-28Z4C-SYS-A/D, N540X-16Z4G8Q2C-A/D, N540-12Z20G-SYS-A/D, and N540X-12Z16G-SYS-A/D variants.
Feature | Description |
---|---|
Segment Routing |
|
This feature builds upon EVPN BGP signaling to provide Emulated Local Area Network (ELAN) multipoint-to-multipoint Ethernet services over an SRv6-based network. This feature introduces the following ELAN-related behaviors:
Automated steering of traffic of an EVPN ELAN service into the path associated with a best-effort or Flex-Algo locator is supported. |
Restrictions and Limitations on the Cisco NCS 540 Series Router
-
Fabric multicast queue stats are not supported in N540X-8Z16G-SYS-A/D, N540X-6Z18G-SYS-A/D, and N540X-4Z14G2Q-A/D variants.
-
Unlabeled BGP PIC EDGE for global prefixes is not supported.
-
The show inventory and the show diagnostic commands do not display the fan serial number for N540-28Z4C-SYS-A/D, N540-12Z20G-SYS-A/D, and N540X-12Z16G-SYS-A/D variants.
-
The interface ports 0/0/0/24 to 0/0/0/31 do not support 1G Copper SFPs on N540-24Z8Q2C-SYS, N540-ACC-SYS, and N540X-ACC-SYS variants. Also, these ports do not support Auto-Negotiation with 1GE optical SFPs and they cannot act as 1GE Synchronous Ethernet sources.
-
The interface ports 0/0/0/20 to 0/0/0/27 do not support 1G Copper SFPs on N540X-16Z4G8Q2C-A and N540X-16Z4G8Q2C-D variants. Also, these ports do not support Auto-Negotiation with 1GE optical SFPs and they cannot act as 1GE Synchronous Ethernet sources.
-
Remove the speed settings on the 1G Copper optics when 10M/100M is configured and replaced with 1G SFP optics.
-
The hw-module profile mfib statistics command is not supported.
Cisco IOS XR Caveats Release 7.5.2
Bug ID | Headline |
---|---|
ipv6 MTU is not changing after configuring form 1500--> 8986 |
IOS XR 7.5.2 Base Images and Optional Packages
For more information on system setup and software installation process, see System Setup and Software Installation Guide for Cisco NCS 540 Series Routers.
For general and ordering information see:
-
Cisco Network Convergence System 540 Fronthaul Routers Data Sheet
-
Cisco Network Convergence System 540 Large Density Router Data Sheet
-
Cisco Network Convergence System 540 Medium Density Routers Data Sheet
-
Cisco Network Convergence System 540 Small Density Router Data Sheet
To install the Cisco NCS 540 Series Routers, see Cisco NCS 540 Router Hardware Installation Guide.
Release 7.5.2 Software
The following tables list the supported base images and optional packages and their corresponding file names.
-
The first table lists the supported software for N540-24Z8Q2C-SYS, N540-ACC-SYS, and N540X-ACC-SYS variants.
-
The second table lists the supported software for N540-24Q8L2DD-SYS, N540X-16Z4G8Q2C-A/D, N540-28Z4C-SYS-A/D, N540X-12Z16G-SYS-A/D, N540-12Z20G-SYS-A/D, N540-FH-CSR-SYS, and N540-FH-AGG-SYS variants.
-
The third table lists the supported software for N540X-4Z14G2Q-A/D, N540X-8Z16G-SYS-A/D and N540X-6Z18G-SYS-A/D variants.
Base Image | Filename | Description |
---|---|---|
IOS XR Base Image |
ncs540-mini-x-7.5.2.iso |
IOS XR mandatory base image. |
USB Boot Package |
ncs540-usb_boot-7.5.2.zip |
Package required to perform USB Boot. Includes the same packages as the base image. |
Optional Packages not included in the base image |
||
Package |
Filename |
Description |
IOS XR Manageability |
ncs540-mgbl-1.0.0.0-r752.x86_64.rpm |
Supports Extensible Markup Language (XML) Parser, Telemetry, Netconf, gRPC and HTTP server |
IOS XR MPLS |
ncs540-mpls-1.0.0.0-r752.x86_64.rpm ncs540-mpls-te-rsvp-1.0.0.0-r752.x86_64.rpm |
Supports MPLS and MPLS Traffic Engineering (MPLS-TE) |
IOS XR Security |
ncs540-k9sec-1.0.0.0-r752.x86_64.rpm |
Supports MACsec and 802.1X |
IOS XR ISIS |
ncs540-isis-1.0.0.0-r752.x86_64.rpm |
Supports ISIS |
IOS XR OSPF |
ncs540-ospf-1.0.0.0-r752.x86_64.rpm |
Supports OSPF |
IOS XR Lawful Intercept |
ncs540-li-1.0.0.0-r752.x86_64.rpm |
Supports Lawful Intercept (LI) |
IOS XR Multicast |
ncs540-mcast-1.0.0.0-r752.x86_64.rpm |
Supports Multicast |
IOS XR EIGRP |
ncs540-eigrp-1.0.0.0-r752.x86_64.rpm |
Supports EIGRP |
IOS XR LI-CTRL |
ncs540-lictrl-1.0.0.0-r752.x86_64.rpm |
Supports LI-CTRL |
Base Image | Filename | Description |
---|---|---|
IOS XR Base Image |
ncs540l-x64-7.5.2.iso |
IOS XR base image with mandatory packages. The base ISO image also includes the following optional packages:
These optional packages are also included in NCS540l-iosxr-7.5.2.tar. |
USB Boot Package |
ncs540l-usb_boot-7.5.2.zip |
Package required to perform USB Boot. Includes the same packages as the base image. |
Optional Packages not included in the base image |
||
Package |
Filename |
Description |
IOS XR Telnet (xr-telnet) |
NCS540l-iosxr-7.5.2.tar |
Supports Telnet |
IOS XR EIGRP (xr-eigrp) |
NCS540l-iosxr-7.5.2.tar |
Supports EIGRP |
IOS XR CDP (xr-cdp) |
NCS540l-iosxr-7.5.2.tar |
Supports CDP |
IOS XR k9sec (xr-k9sec) |
NCS540l-k9sec-rpms.7.5.2.tar |
Supports 802.1X |
IOS XR RIP (xr-rip) |
NCS540l-iosxr-7.5.2.tar |
Supports RIP |
Base Image | Filename | Description |
---|---|---|
IOS XR Base Image |
ncs540l-aarch64-7.5.2.iso |
IOS XR base image with mandatory packages. The ISO image also includes the following optional packages:
These optional packages are also included in NCS540l-aarch64-iosxr-optional-rpms-7.5.2.tar. |
USB Boot Package |
ncs540l-aarch64-usb_boot-7.5.2.zip |
Package required to perform USB Boot. Includes the same packages as the base image. |
Optional Packages not included in the base image |
||
Package |
Filename |
Description |
IOS XR Telnet (xr-telnet) |
NCS540l-aarch64-iosxr-optional-rpms-7.5.2.tar |
Supports Telnet |
IOS XR EIGRP (xr-eigrp) |
NCS540l-aarch64-iosxr-optional-rpms-7.5.2.tar |
Supports EIGRP |
IOS XR CDP (xr-cdp) |
NCS540l-aarch64-iosxr-optional-rpms-7.5.2.tar |
Supports CDP |
IOS XR k9sec (xr-k9sec) |
NCS540l-aarch64-k9sec-rpms.7.5.2.tar |
Supports 802.1X |
IOS XR RIP (xr-rip) |
NCS540l-aarch64-iosxr-optional-rpms-7.5.2.tar |
Supports RIP |
Determine Software Version
Log in to the router and enter the show version command on the N540-24Z8Q2C-SYS, N540-ACC-SYS, and N540X-ACC-SYS variants:
RP/0/RP0/CPU0:R1_PE1#show version
Wed Apr 27 14:55:59.804 IST
Cisco IOS XR Software, Version 7.5.2
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Tue Apr 26 18:53:00 PDT 2022
Built Host : iox-lnx-010
Workspace : /auto/srcarchive14/prod/7.5.2/ncs540/ws
Version : 7.5.2
Location : /opt/cisco/XR/packages/
Label : 7.5.2
cisco NCS-540 () processor
System uptime is 1 hour 4 minutes
Log in to the router and enter the show version command on the N540X-16Z4G8Q2C-A/D, N540-28Z4C-SYS-A/D, N540X-12Z16G-SYS-A/D, and N540-12Z20G-SYS-A/D variants:
RP/0/RP0/CPU0:R11_PE5_EG#show version
Wed Apr 27 14:59:51.584 IST
Cisco IOS XR Software, Version 7.5.2 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Tue Apr 26 23:20:19 UTC 2022
Build Host : iox-lnx-011
Workspace : /auto/srcarchive14/prod/7.5.2/ncs540l/ws
Version : 7.5.2
Label : 7.5.2
cisco NCS540L (C3708 @ 1.70GHz)
cisco N540X-16Z4G8Q2C-A (C3708 @ 1.70GHz) processor with 8GB of memory
PE3-EG uptime is 2 hours, 33 minutes
Cisco NCS 540 System with 16x10G+4x1GCu+8x25G+2x100G AC Chassis
Log in to the router and enter the show version command on the N540-6Z14S-SYS-D, N540X-8Z16G-SYS-A/D, and N540X-6Z18G-SYS-A/D variants:
RP/0/RP0/CPU0:R15_PE7_GP#show version
Wed Apr 27 08:58:15.991 UTC
Cisco IOS XR Software, Version 7.5.2 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Tue Apr 26 23:47:22 UTC 2022
Build Host : iox-lnx-023
Workspace : /auto/srcarchive14/prod/7.5.2/ncs540l-aarch64/ws
Version : 7.5.2
Label : 7.5.2
cisco NCS540L
cisco N540-6Z14S-SYS-D processor with 8GB of memory
APE-15 uptime is 2 hours, 44 minutes
Cisco NCS 540 Series Fixed Router 10x1G, 4xCu, 6x1/10G, DC
Log in to the router and enter the show version command on the N540-24Q8L2DD-SYS variant:
RP/0/RP0/CPU0:R1_PE1#show version
Wed Apr 27 09:46:11.123 UTC
Cisco IOS XR Software, Version 7.5.2 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Tue Apr 26 23:20:19 UTC 2022
Build Host : iox-lnx-011
Workspace : /auto/srcarchive14/prod/7.5.2/ncs540l/ws
Version : 7.5.2
Label : 7.5.2
cisco NCS540L (D1519 @ 1.50GHz)
cisco N540-24Q8L2DD-SYS (D1519 @ 1.50GHz) processor with 16GB of memory
APE-13 uptime is 2 hours, 54 minutes
Cisco NCS540 Series, Fixed Router 2x400G, 8x50G, 24x25G Chassis
Log in to the router and enter the show version command on the N540-FH-CSR-SYS variant:
RP/0/RP0/CPU0:R1_PE1#show version
Wed Apr 27 09:43:25.368 UTC
Cisco IOS XR Software, Version 7.5.2 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Tue Apr 26 23:20:19 UTC 2022
Build Host : iox-lnx-011
Workspace : /auto/srcarchive14/prod/7.5.2/ncs540l/ws
Version : 7.5.2
Label : 7.5.2
cisco NCS540L (C3708 @ 1.70GHz)
cisco N540-FH-CSR-SYS (C3708 @ 1.70GHz) processor with 8GB of memory
APE-12 uptime is 2 hours, 45 minutes
Cisco NCS 540 FH with 8xCPRI+4xCPRI/10G+8x10G+6x25G+2x100G
Determine Firmware Support
Usethe show command in EXEC mode to view the hardware components with their current FPD version and status. The status of the hardware must be “CURRENT”; Running and Programed version must be the same. The Golden FPDs with “NEED UPGD” can be ignored, the Golden FPDs are not upgradable.
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-24Z8Q2C-SYS, N540X-ACC-SYS, and N540-ACC-SYS variants:
RP/0/RP0/CPU0:R1_PE1# show fpd package
Wed Apr 27 09:22:47.950 UTC+00:00
=============================== ====================================================
Field Programmable Device Package
====================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ========== =========
N540-24Z8Q2C-M Bootloader YES 1.14 1.14 0.0
CPU-IOFPGA YES 0.07 0.07 0.0
MB-IOFPGA YES 0.23 0.23 0.0
SATA-M500IT-MC NO 3.00 3.00 0.0
SATA-M500IT-MU-A NO 5.00 5.00 0.0
SATA-M500IT-MU-B NO 4.00 4.00 0.0
SATA-M5100 NO 71.00 71.00 0.0
SATA-M600-MCT NO 5.00 5.00 0.0
SATA-SMART-128G NO 1241.00 1241.00 0.0
------------------------------------------------------------------------------------
N540-ACC-SYS Bootloader YES 1.14 1.14 0.0
CPU-IOFPGA YES 0.07 0.07 0.0
MB-IOFPGA YES 0.23 0.23 0.0
SATA-M500IT-MC NO 3.00 3.00 0.0
SATA-M500IT-MU-A NO 5.00 5.00 0.0
SATA-M500IT-MU-B NO 4.00 4.00 0.0
SATA-M5100 NO 71.00 71.00 0.0
SATA-M600-MCT NO 5.00 5.00 0.0
SATA-SMART-128G NO 1241.00 1241.00 0.0
------------------------------------------------------------------------------------
N540-PWR400-A LIT-PriMCU-ACFW NO 0.04 0.04 0.0
LIT-SecMCU-ACFW NO 0.07 0.07 0.0
------------------------------------------------------------------------------------
N540-PWR400-D LIT-PriMCU-DCFW NO 0.04 0.04 0.0
LIT-SecMCU-DCFW NO 0.06 0.06 0.0
SDG-PriMCU-DCFW NO 1.03 1.03 0.0
SDG-SecMCU-DCFW NO 1.03 1.03 0.0
------------------------------------------------------------------------------------
N540-X-24Z8Q2C-M Bootloader YES 1.14 1.14 0.0
CPU-IOFPGA YES 0.07 0.07 0.0
MB-IOFPGA YES 0.23 0.23 0.0
SATA-M500IT-MC NO 3.00 3.00 0.0
SATA-M500IT-MU-A NO 5.00 5.00 0.0
SATA-M500IT-MU-B NO 4.00 4.00 0.0
SATA-M5100 NO 71.00 71.00 0.0
SATA-M600-MCT NO 5.00 5.00 0.0
SATA-SMART-128G NO 1241.00 1241.00 0.0
------------------------------------------------------------------------------------
N540X-ACC-SYS Bootloader YES 1.14 1.14 0.0
CPU-IOFPGA YES 0.07 0.07 0.0
MB-IOFPGA YES 0.23 0.23 0.0
SATA-M500IT-MC NO 3.00 3.00 0.0
SATA-M500IT-MU-A NO 5.00 5.00 0.0
SATA-M500IT-MU-B NO 4.00 4.00 0.0
SATA-M5100 NO 71.00 71.00 0.0
SATA-M600-MCT NO 5.00 5.00 0.0
SATA-SMART-128G NO 1241.00 1241.00 0.0
------------------------------------------------------------------------------------
RP/0/RP0/CPU0:R1_PE1# show hw-module fpd
Wed Apr 27 09:23:04.331 UTC+00:00
FPD Versions
==============
Location Card type HWver FPD device ATR Status Run Programd
-----------------------------------------------------------------------------------
0/RP0 N540-24Z8Q2C-M 1.0 Bootloader CURRENT 1.14 1.14
0/RP0 N540-24Z8Q2C-M 1.0 CPU-IOFPGA CURRENT 0.07 0.07
0/RP0 N540-24Z8Q2C-M 1.0 MB-IOFPGA CURRENT 0.23 0.23
0/RP0 N540-24Z8Q2C-M 1.0 SATA-M500IT-MU-B CURRENT 4.00 4.00
0/PM0 N540-PWR400-A 1.0 SDG-PriMCU-ACFW CURRENT 0.00 0.00
0/PM0 N540-PWR400-A 1.0 SDG-SecMCU-ACFW CURRENT 0.00 0.00
0/PM1 N540-PWR400-A SDG-PriMCU-ACFW NOT READY
0/PM1 N540-PWR400-A SDG-SecMCU-ACFW NOT READY
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-28Z4C-SYS-A/D, N540-12Z20G-SYS-A/D, N540X-12Z16G-SYS-A/D and N540X-16Z4G8Q2C-A/D variants:
RP/0/RP0/CPU0:R11_PE5_EG#show fpd package
Wed Apr 27 15:02:52.049 IST
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-12Z20G-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-12Z20G-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-24Q8L2DD-SYS ADM-DBConfig YES 2.03 2.03 0.0
ADM-MBConfig YES 2.01 2.01 0.0
IoFpga YES 2.12 2.12 0.0
IoFpgaGolden YES 2.12 2.12 0.0
Primary-BIOS YES 1.08 1.08 0.0
StdbyFpga YES 2.59 2.59 0.0
StdbyFpgaGolden YES 2.56 2.39 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-FH-AGG-SYS ADM1_Config YES 1.02 1.02 1.0
ADM2_Config YES 1.02 1.02 1.0
DpFpgaCpri YES 0.20 0.20 0.0
DpFpgaEth YES 1.18 1.18 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-CSR-SYS ADM1_Config YES 0.09 0.09 0.0
ADM1_Config YES 1.01 1.01 2.0
ADM2_Config YES 0.09 0.09 0.0
ADM2_Config YES 1.01 1.01 2.0
DpFpga YES 0.19 0.19 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-IP65-SYS DpFpga YES 0.19 0.19 0.0
IoFpga YES 1.24 1.24 0.0
IoFpgaGolden YES 1.24 1.24 0.0
Primary-BIOS YES 1.17 1.17 0.0
StdbyFpga YES 0.43 0.43 0.0
StdbyFpgaGolden YES 0.43 0.43 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.02 1.02 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.03 1.03 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-A EM-PrimMCU NO 1.02 1.02 0.0
EM-SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-D EM-PrimMCU NO 1.03 1.03 0.0
EM-SecMCU NO 3.01 3.01 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
RP/0/RP0/CPU0:R1_PE1# show hw-module fpd
Wed Apr 27 15:03:23.226 IST
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 ADMConfig NEED UPGD 1.03 1.03 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 IoFpga CURRENT 2.07 2.07 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 IoFpgaGolden B NEED UPGD 1.31 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 Primary-BIOS S CURRENT 1.33 1.33 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 StdbyFpga S CURRENT 0.40 0.40 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 StdbyFpgaGolden BS NEED UPGD 0.00 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 TamFw S CURRENT 4.11 4.11 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 0.3 TamFwGolden BS NEED UPGD 0.00 0/RP0
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-6Z14S-SYS-D, N540X-6Z18G-SYS-A/D, and N540X-8Z16G-SYS-A/D variants:
RP/0/RP0/CPU0:R15_PE7_GP#show fpd package
Wed Apr 27 08:58:56.981 UTC
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-6Z14S-SYS-D ADMConfig YES 5.03 5.03 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 1.09 1.09 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-4Z14G2Q-A ADMConfig YES 5.00 5.00 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.34 0.34 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-4Z14G2Q-D ADMConfig YES 5.00 5.00 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.34 0.34 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-6Z18G-SYS-A ADMConfig YES 5.00 5.00 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.34 0.34 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-6Z18G-SYS-D ADMConfig YES 5.00 5.00 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.34 0.34 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-8Z16G-SYS-A ADMConfig YES 5.00 5.00 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.34 0.34 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-8Z16G-SYS-D ADMConfig YES 5.00 5.00 0.0
BckUp-BootLoader YES 20.04 20.04 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.17 0.17 0.0
Prim-BootLoader YES 20.04 20.04 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.34 0.34 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
RP/0/RP0/CPU0:Leaf5#show hw-module fpd
Wed Apr 27 08:59:29.144 UTC
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 ADMConfig CURRENT 5.03 5.03 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 IoFpga CURRENT 0.17 0.17 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 IoFpgaGolden B NEED UPGD 0.15 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 Prim-BootLoader CURRENT 20.04 20.04 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 StdbyFpga S CURRENT 1.09 1.09 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 StdbyFpgaGolden BS NEED UPGD 0.33 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 TamFw S CURRENT 6.05 6.05 0/RP0
0/RP0/CPU0 N540-6Z14S-SYS-D 0.2 TamFwGolden BS CURRENT 6.05 0/RP0
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-24Q8L2DD-SYS variant:
RP/0/RP0/CPU0:R1_PE1# show fpd package
Wed Apr 27 09:46:51.293 UTC
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-12Z20G-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-12Z20G-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-24Q8L2DD-SYS ADM-DBConfig YES 2.03 2.03 0.0
ADM-MBConfig YES 2.01 2.01 0.0
IoFpga YES 2.12 2.12 0.0
IoFpgaGolden YES 2.12 2.12 0.0
Primary-BIOS YES 1.08 1.08 0.0
StdbyFpga YES 2.59 2.59 0.0
StdbyFpgaGolden YES 2.56 2.39 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-FH-AGG-SYS ADM1_Config YES 1.02 1.02 1.0
ADM2_Config YES 1.02 1.02 1.0
DpFpgaCpri YES 0.20 0.20 0.0
DpFpgaEth YES 1.18 1.18 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-CSR-SYS ADM1_Config YES 0.09 0.09 0.0
ADM1_Config YES 1.01 1.01 2.0
ADM2_Config YES 0.09 0.09 0.0
ADM2_Config YES 1.01 1.01 2.0
DpFpga YES 0.19 0.19 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-IP65-SYS DpFpga YES 0.19 0.19 0.0
IoFpga YES 1.24 1.24 0.0
IoFpgaGolden YES 1.24 1.24 0.0
Primary-BIOS YES 1.17 1.17 0.0
StdbyFpga YES 0.43 0.43 0.0
StdbyFpgaGolden YES 0.43 0.43 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.02 1.02 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.03 1.03 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-A EM-PrimMCU NO 1.02 1.02 0.0
EM-SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-D EM-PrimMCU NO 1.03 1.03 0.0
EM-SecMCU NO 3.01 3.01 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
RP/0/RP0/CPU0:R1_PE1# show hw-module fpd
Wed Apr 27 09:47:14.880 UTC
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 ADM-DBConfig NEED UPGD 2.02 2.02 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 ADM-MBConfig NEED UPGD 1.02 1.02 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 IoFpga CURRENT 2.12 2.12 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 IoFpgaGolden B CURRENT 2.12 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 Primary-BIOS S NOT READY 1.05 1.05 N/A
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 StdbyFpga S CURRENT 2.59 2.59 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 StdbyFpgaGolden BS NEED UPGD 0.00 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 TamFw S CURRENT 6.05 6.05 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 3.0 TamFwGolden BS NEED UPGD 0.00 0/RP0
0/PM1 N540-PWR400-A 0.0 PrimMCU CURRENT 1.02 1.02 NOT REQ
0/PM1 N540-PWR400-A 0.0 SecMCU CURRENT 1.03 1.03 NOT REQ
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-FH-CSR-SYS variant:
RP/0/RP0/CPU0:R1_PE1# show fpd package
Wed Apr 27 09:44:56.091 UTC
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-12Z20G-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-12Z20G-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-24Q8L2DD-SYS ADM-DBConfig YES 2.03 2.03 0.0
ADM-MBConfig YES 2.01 2.01 0.0
IoFpga YES 2.12 2.12 0.0
IoFpgaGolden YES 2.12 2.12 0.0
Primary-BIOS YES 1.08 1.08 0.0
StdbyFpga YES 2.59 2.59 0.0
StdbyFpgaGolden YES 2.56 2.39 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-FH-AGG-SYS ADM1_Config YES 1.02 1.02 1.0
ADM2_Config YES 1.02 1.02 1.0
DpFpgaCpri YES 0.20 0.20 0.0
DpFpgaEth YES 1.18 1.18 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-CSR-SYS ADM1_Config YES 0.09 0.09 0.0
ADM1_Config YES 1.01 1.01 2.0
ADM2_Config YES 0.09 0.09 0.0
ADM2_Config YES 1.01 1.01 2.0
DpFpga YES 0.19 0.19 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-IP65-SYS DpFpga YES 0.19 0.19 0.0
IoFpga YES 1.24 1.24 0.0
IoFpgaGolden YES 1.24 1.24 0.0
Primary-BIOS YES 1.17 1.17 0.0
StdbyFpga YES 0.43 0.43 0.0
StdbyFpgaGolden YES 0.43 0.43 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.02 1.02 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.03 1.03 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-A EM-PrimMCU NO 1.02 1.02 0.0
EM-SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-D EM-PrimMCU NO 1.03 1.03 0.0
EM-SecMCU NO 3.01 3.01 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-A ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-D ADMConfig YES 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
RP/0/RP0/CPU0:R1_PE1# show hw-module fpd
Wed Apr 27 09:45:15.446 UTC
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 ADM1_Config CURRENT 0.09 0.09 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 ADM2_Config CURRENT 0.09 0.09 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 DpFpga CURRENT 0.19 0.19 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 IoFpga CURRENT 1.30 1.30 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 IoFpgaGolden B NEED UPGD 1.23 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 Primary-BIOS S CURRENT 1.33 1.33 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 StdbyFpga S CURRENT 0.46 0.46 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 StdbyFpgaGolden BS NEED UPGD 0.43 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 TamFw S CURRENT 6.05 6.05 0/RP0
0/RP0/CPU0 N540-FH-CSR-SYS 1.0 TamFwGolden BS CURRENT 6.05 0/RP0
0/PM0 N540-PWR400-A 0.0 PrimMCU CURRENT 1.02 1.02 NOT REQ
0/PM0 N540-PWR400-A 0.0 SecMCU CURRENT 1.03 1.03 NOT REQ
Important Information
Supported Transceiver Modules
For more information on the supported transceiver modules, see Transceiver Module Group (TMG) Compatibility Matrix. In the Begin your Search search box, enter the keyword NCS540 and click Enter.
Upgrading Cisco IOS XR Software
Cisco IOS XR Software is installed and activated from modular packages, allowing specific features or software patches to be installed, upgraded, or downgraded without affecting unrelated processes.
The upgrade document for N540-24Z8Q2C-SYS, N540X-ACC-SYS, and N540-ACC-SYS variants is available along with the software image in NCS540-docs-7.5.2.tar file.
The upgrade document for N540-28Z4C-SYS-A/D, N540-12Z20G-SYS-A/D, N540X-12Z16G-SYS-A/D, N540X-16Z4G8Q2C-A/D, N540-24Q8L2DD-SYS, N540-FH-AGG-SYS, and N540-FH-CSR-SYS variants are available along with the software image in NCS540l-docs-7.5.2.tar file.
The upgrade document for N540X-4Z14G2Q-A/D, N540X-8Z16G-SYS-A/D, and N540X-6Z18G-SYS-A/D variants is available along with the software image in NCS540l-aarch64-docs-7.5.2.tar file.
Note |
Quad configurations will be lost when you perform a software downgrade on Cisco NCS 540 Routers that support quad configurations from IOS XR Release 7.5.1 onwards to a release prior to IOS XR Release 7.5.1 due to a non-backward compatibility change. The lost configuration can be applied manually after the downgrade. |
Use user-class Option 'xr-config' Instead Of 'exr-config' To Provision ZTP
In Cisco IOS XR Release 7.3.1 and earlier, the system accepts the device sending user-class = "exr-config"; however starting Cisco IOS XR Release 7.3.2 and later, you must use only user-class = "xr-config".
In Cisco IOS XR Release 7.3.2 and later, use:
host cisco-rp0 {
hardware ethernet e4:c7:22:be:10:ba;
fixed-address 172.30.12.54;
if exists user-class and option user-class = "iPXE" {
filename = "http://172.30.0.22/boot.ipxe";
} elsif exists user-class and option user-class = "xr-config" {
filename = "http://172.30.0.22/scripts/cisco-rp0_ztp.sh";
}
}
Additional References
Supported MIBs
The Cisco NCS 5500 MIB support list is also applicable to the Cisco NCS 540 Series Routers. For the list of supported MIBs, see the Cisco NCS5500 MIB Support List.