What's New in Cisco IOS XR Release 7.7.1
Hardware |
Description |
||
---|---|---|---|
Optics |
This release introduces the following optics:
|
The following features are supported on all the NCS 540 variants.
Feature | Description |
---|---|
Modular QoS |
|
In terms of preserving IP DSCP markings, this release covers two scenarios for SR-TE traffic:
With preservation, traffic with IP packets with DSCP marking for priority, flows as intended and there’s no drop in traffic because of incorrect or missing labels. In previous releases, irrespective of the number of MPLS labels, when the EXP values were copied into the packet header during imposition, even the IP DSCP markings were modified. This modification resulted in traffic drops at the next-hop routers in SR-TE tunnels. This feature introduces the hw-module profile mpls-ext-dscp-preserve v4uc-enable command. |
|
Routing |
|
You can set a multihop BFD session using IPv4 for a non-default-VRF between a source and destination endpoints that have IP
connectivity. This feature provides subsecond forwarding failure detection for a destination more than one hop, and up to
255 hops away.
IPv4 Multihop BFD is a BFD session between two nodes, such as a PE and CE node, or between routers that are several TTL hops away. You can extend the BFD session to nondefault VRFs. This feature enables you to extend the BFD session to nondefault VRFs. Thus, the advantage of BFD, low-overhead, and short-duration detection of path failures between routers, is extended to a multihop scenario. |
|
Setting SPF interval in IS-IS to postpone the IS-IS SPF computations |
You can now define a standard algorithm to postpone the IS-IS SPF computations by setting an SPF interval. This reduces the computational load and churn on IGP nodes when multiple temporally close network events trigger multiple SPF computations. This algorithm also reduces the probability and the duration of transient forwarding loops during native IS-IS convergence when the protocol reacts to multiple temporally close events. This feature complies with RFC 8405. This feature introduces the spf-interval ietf command. |
Multicast |
|
Qos DSCP Preservation |
In terms of preserving IP DSCP markings, when you set the MPLS experimental bits (EXP) values (also called Traffic Class values), the IP DSCP markings are now preserved by default in the ingress policies when the MPLS labels are pushed into the packet. Traffic with IP packets with DSCP marking for priority, flows as intended and there’s no drop in traffic because of incorrect or missing labels. In previous releases, irrespective of the number of MPLS labels, when the EXP values were copied into the packet header during imposition, even the IP DSCP markings were modified. This modification resulted in traffic drops at the next-hop routers. |
Extending Selective Multicast using IGMP Proxy |
The IGMP Proxy function enables PE routers to act as a proxy for the CE routers connected to it. IGMP Proxy function provides the following benefits:
Earlier, connecting an external network directly to an EVPN fabric was not possible. With this IGMP Proxy support, it is possible to have seamless connectivity over the EVPN network for its hosts with respect to multicast operations. |
System Security |
|
We have enhanced the system security to minimize the automated attacks that may target the default Secure Socket Shell (SSH) port on your router. You can now specify a non-default port number for the SSH server on your router. The SSH, Secure Copy Protocol (SCP), and Secure File Transfer Protocol (SFTP) client services can then access your router only through this non-default port. The new port option also enables the SSH, SCP, and SFTP clients on your router to connect to SSH servers on the network that use a wide range of non-default port numbers. In earlier releases, these SSH, SCP, and SFTP connections were established through the default SSH port, 22. The non-default SSH port is supported only on SSH version 2. The feature modifies these commands to include the port option: |
|
We have enhanced the router security by enforcing a strong password policy for all users configured on the router. You can now specify a new password policy for the user that restricts the usage of a specific number of consecutive characters for the login passwords. These characters include English alphabets, the sequence of QWERTY keyboard layout, and numbers, such as, 'abcd', 'qwer', '1234', and so on. Apart from passwords, the feature is also applicable for secrets–the one-way encrypted secure login passwords that are not easy to decrypt to retrieve the original unencrypted password text. The password policy is applicable only for the users configured on the local AAA server on the router; not those configured on the remote AAA server. The feature introduces the restrict-consecutive-characters command. |
|
Interface and Hardware Component |
|
You can now configure the size of bins for the delay and jitter measurement in Ethernet SLA statistics with a width value ranging from 1 to 10000000 microseconds. This enhancement provides granularity to store more accurate results of SLA statistics in the aggregate bins. In earlier releases, you could only configure the width value for the delay and jitter measurement in milliseconds. This feature introduces usec keyword in the aggregate command. |
|
System Setup and Software Installation |
|
ZTP over Layer 2 is now supported on the following NCS 540 router variants.
|
|
Segment Routing |
|
The modified hw-module profile segment-routing srv6 mode command option provides you with better flexibility to customize the optional SRv6 encapsulation parameters. The updated command will now support both L2 and L3 traffic types of SRv6 parameters. Encapsulation is a sub-mode from Release 7.7.1. The l3-traffic config supports the additional policy-map option that sets SRv6 traffic-class DSCP based on qos-group selected by input policy-map. The following commands are updated:
The following commands are introduced: |
|
System Monitoring |
|
Out of Resource handling of Input Logical Interface and Router Interface |
You can now reconfigure the threshold level for NPU resources - Input Logical Interface (INLIF) and Router Interface (RIF) by changing the predefined threshold level at which Out of Resource (OOR) situation is triggered. Graceful handling of OOR helps you to minimize traffic loss. You get notified via systemlogs, when the utilization of resources reaches their OOR limit. Also, you can view the utilization of resources by using the following commands: |
Network Synchronization |
|
PTP Double Failure Clock Class |
This feature enables you to configure a clock class that will override the existing class during a state of double-failure where PTP and SyncE are lost. This feature introduces the double-failure-clock-class command. |
System Management |
|
Unified Model: Cisco-IOS-XR-um-fpd-cfg |
We have introduced the Cisco-IOS-XR-um-fpd-cfg unified model to enable or disable the automatic reload and automatic upgrade of Field Programmable Devices. You can access this unified model from the Github repository. |
The following features are supported on N540-ACC-SYS, N540X-ACC-SYS, and N540-24Z8Q2C-SYS variants.
Feature | Description |
---|---|
Modular QoS |
|
If the ASIC packet processing capacity is overloaded with continuous flow of packets, it’s called oversubscription and it results in packet drops at the interface level. By enabling prioritization of packets during oversubscription, you can protect the high priority traffic. This feature introduces the hw-module oversubscription command. |
The following features are supported on N540-ACC-SYS, N540X-ACC-SYS, N540-24Z8Q2C-SYS, N540-28Z4C-SYS-A/D, N540X-16Z4G8Q2C-A/D, N540-12Z20G-SYS-A/D, N540X-12Z16G-SYS-A/D, and N540-24Q8L2DD-SYS variants.
Feature | Description | ||||
---|---|---|---|---|---|
System Security |
|||||
MACSec, the Layer 2 encryption protocol, secures the data on physical media and provides data integrity and confidentiality. MACSec is now supported on the following Cisco NCS 540 router variant:
|
|||||
Network Synchronization |
|||||
Assisted Partial Timing Support (APTS) is now available on the following Cisco NCS 540 router variants:
APTS allows for proper distribution of phase and time synchronization in the network. |
|||||
PTP Virtual Port Support for N540X-12Z16G-SYS-A/D and N540-24Q8L2DD-SYS |
PTP Virtual Port is now supported on the following Cisco NCS 540 router variants:
|
||||
For ITU-T G.8275.2 and the IEEE 1588 default PTP profiles, the encapsulation type for PTP packet transport is now extended to IPv6. The transport command now accepts the keyword ipv6. In this release, this feature is supported on the following Cisco NCS 540 router variants:
|
|||||
Synchronous Ethernet ESMC and SSM are now supported on the following Cisco NCS 540 router variant:
For 1G ports, clock recovery is supported only on ports 4 to 19. |
YANG Data Models Introduced and Enhanced
This release introduces or enhances the following data models. For detailed information about the supported and unsupported sensor paths of all the data models, see the Github repository. To get a comprehensive list of the data models supported in a release, navigate to the Available-Content.md file for the release in the Github repository. The unsupported sensor paths are documented as deviations. For example, openconfig-acl.yang provides details about the supported sensor paths, whereas cisco-xr-openconfig-acl-deviations.yang provides the unsupported sensor paths for openconfig-acl.yang on Cisco IOS XR routers.
Feature | Description |
---|---|
Programmability |
|
OpenConfig Model: openconfig-inet-types Version 0.4.1 |
We have now revised the openconfig-inet-types open configuration from version 0.3.1 to 0.4.1. With this revision, this data model supports autogenerated regular expressions for faster validation of text strings for the following IPv4 pattern statement:
You can access the OC data model from the Github repository. |
openconfig-platform-transceiver Revision 0.7.0 |
The OpenConfig data model configures the mapping of optical channel with the configured physical channel, and physical port with the configured interface using the following XPaths:
|
openconfig-terminal-device Revision 1.7.2 |
The OpenConfig data model configures terminal optics devices up to 400G bandwidth to manage the line side terminal systems in a Dense wavelength-division multiplexing (DWDM) transport network using the following XPaths:
|
Restrictions and Limitations on the Cisco NCS 540 Series Router
-
Fabric multicast queue stats are not supported in N540X-8Z16G-SYS-A/D, N540X-6Z18G-SYS-A/D, and N540X-4Z14G2Q-A/D variants.
-
Unlabeled BGP PIC EDGE for global prefixes is not supported.
-
The show inventory and the show diagnostic commands do not display the fan serial number for N540-28Z4C-SYS-A/D, N540-12Z20G-SYS-A/D, and N540X-12Z16G-SYS-A/D variants.
-
The interface ports 0/0/0/24 to 0/0/0/31 do not support 1G Copper SFPs on N540-24Z8Q2C-SYS, N540-ACC-SYS, and N540X-ACC-SYS variants. Also, these ports do not support Auto-Negotiation with 1GE optical SFPs and they cannot act as 1GE Synchronous Ethernet sources.
-
The interface ports 0/0/0/20 to 0/0/0/27 do not support 1G Copper SFPs on N540X-16Z4G8Q2C-A and N540X-16Z4G8Q2C-D variants. Also, these ports do not support Auto-Negotiation with 1GE optical SFPs and they cannot act as 1GE Synchronous Ethernet sources.
-
Remove the speed settings on the 1G Copper optics when 10M/100M is configured and replaced with 1G SFP optics.
-
The hw-module profile mfib statistics command is not supported.
Cisco IOS XR Caveats Release 7.7.1
Bug ID |
Headline |
---|---|
Continuous HW_PROG_ERROR seen after commit replace of configuration |
|
Provisioning in progress alarm on ots-och on shut and no shut of ots0/0/0/0 |
IOS XR Base Images and Optional Packages
For more information on system setup and software installation process, see System Setup and Software Installation Guide for Cisco NCS 540 Series Routers.
For general and ordering information see:
-
Cisco Network Convergence System 540 Fronthaul Routers Data Sheet
-
Cisco Network Convergence System 540 Large Density Router Data Sheet
-
Cisco Network Convergence System 540 Medium Density Routers Data Sheet
-
Cisco Network Convergence System 540 Small Density Router Data Sheet
To install the Cisco NCS 540 Series Routers, see Cisco NCS 540 Router Hardware Installation Guide.
Release 7.7.1 Software
The following tables list the supported base images and optional packages and their corresponding file names.
-
The first table lists the supported software for N540-24Z8Q2C-SYS, N540-ACC-SYS, and N540X-ACC-SYS variants.
-
The second table lists the supported software for N540-24Q8L2DD-SYS, N540X-16Z4G8Q2C-A/D, N540-28Z4C-SYS-A/D, N540X-12Z16G-SYS-A/D, N540-12Z20G-SYS-A/D, N540-FH-CSR-SYS, and N540-FH-AGG-SYS variants.
-
The third table lists the supported software for N540X-4Z14G2Q-A/D, N540X-8Z16G-SYS-A/D and N540X-6Z18G-SYS-A/D variants.
Base Image |
Filename |
Description |
IOS XR Base Image |
ncs540-mini-x-7.7.1.iso |
IOS XR mandatory base image. |
USB Boot Package |
ncs540-usb_boot-7.7.1.zip |
Package required to perform USB Boot. Includes the same packages as the base image. |
Optional Packages not included in the base image |
||
Package |
Filename |
Description |
IOS XR Manageability |
ncs540-mgbl-1.0.0.0-r771.x86_64.rpm |
Supports Extensible Markup Language (XML) Parser, Telemetry, Netconf, gRPC and HTTP server |
IOS XR MPLS |
ncs540-mpls-1.0.0.0-r771.x86_64.rpm ncs540-mpls-te-rsvp-1.0.0.0-r771.x86_64.rpm |
Supports MPLS and MPLS Traffic Engineering (MPLS-TE) |
IOS XR Security |
ncs540-k9sec-1.0.0.0-r771.x86_64.rpm |
Supports MACsec and 802.1X |
IOS XR ISIS |
ncs540-isis-1.0.0.0-r771.x86_64.rpm |
Supports ISIS |
IOS XR OSPF |
ncs540-ospf-1.0.0.0-r771.x86_64.rpm |
Supports OSPF |
IOS XR Lawful Intercept |
ncs540-li-1.0.0.0-r771.x86_64.rpm |
Supports Lawful Intercept (LI) |
IOS XR Multicast |
ncs540-mcast-1.0.0.0-r771.x86_64.rpm |
Supports Multicast |
IOS XR EIGRP |
ncs540-eigrp-1.0.0.0-r771.x86_64.rpm |
Supports EIGRP |
IOS XR LI-CTRL |
ncs540-lictrl-1.0.0.0-r771.x86_64.rpm |
Supports LI-CTRL |
Base Image |
Filename |
Description |
IOS XR Base Image |
ncs540l-x64-7.7.1.iso |
IOS XR base image with mandatory packages. The base ISO image also includes the following optional packages:
These optional packages are also included in NCS540l-iosxr-7.7.1.tar. |
USB Boot Package |
ncs540l-usb_boot-7.7.1.zip |
Package required to perform USB Boot. Includes the same packages as the base image. |
Optional Packages not included in the base image |
||
Package |
Filename |
Description |
IOS XR Telnet (xr-telnet) |
NCS540l-iosxr-7.7.1.tar |
Supports Telnet |
IOS XR EIGRP (xr-eigrp) |
NCS540l-iosxr-7.7.1.tar |
Supports EIGRP |
IOS XR CDP (xr-cdp) |
NCS540l-iosxr-7.7.1.tar |
Supports CDP |
IOS XR k9sec (xr-k9sec) |
NCS540l-k9sec-rpms.7.7.1.tar |
Supports 802.1X |
IOS XR RIP (xr-rip) |
NCS540l-iosxr-7.7.1.tar |
Supports RIP |
Base Image |
Filename |
Description |
IOS XR Base Image |
ncs540l-aarch64-7.7.1.iso |
IOS XR base image with mandatory packages. The ISO image also includes the following optional packages:
These optional packages are also included in NCS540l-aarch64-iosxr-optional-rpms-7.7.1.tar. |
USB Boot Package |
ncs540l-aarch64-usb_boot-7.7.1.zip |
Package required to perform USB Boot. Includes the same packages as the base image. |
Optional Packages not included in the base image |
||
Package |
Filename |
Description |
IOS XR Telnet (xr-telnet) |
NCS540l-aarch64-iosxr-optional-rpms-7.7.1.tar |
Supports Telnet |
IOS XR EIGRP (xr-eigrp) |
NCS540l-aarch64-iosxr-optional-rpms-7.7.1.tar |
Supports EIGRP |
IOS XR CDP (xr-cdp) |
NCS540l-aarch64-iosxr-optional-rpms-7.7.1.tar |
Supports CDP |
IOS XR k9sec (xr-k9sec) |
NCS540l-aarch64-k9sec-rpms.7.7.1.tar |
Supports 802.1X |
IOS XR RIP (xr-rip) |
NCS540l-aarch64-iosxr-optional-rpms-7.7.1.tar |
Supports RIP |
Determine Software Version
Log in to the router and enter the show version command on the N540-24Z8Q2C-SYS, N540-ACC-SYS, and N540X-ACC-SYS variants:
RP/0/RP0/CPU0:Router# show version
Cisco IOS XR Software, Version 7.7.1
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Mon Jul 25 02:19:41 PDT 2022
Built Host : iox-lnx-096
Workspace : /auto/srcarchive12/prod/7.7.1/ncs540/ws
Version : 7.7.1
Location : /opt/cisco/XR/packages/
Label : 7.7.1
cisco NCS-540 () processor
System uptime is 5 hours 1 minute
Log in to the router and enter the show version command on the N540X-16Z4G8Q2C-A/D, N540-28Z4C-SYS-A/D, N540X-12Z16G-SYS-A/D, and N540-12Z20G-SYS-A/D variants:
RP/0/RP0/CPU0:Router# show version
Cisco IOS XR Software, Version 7.7.1 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Mon Jul 25 06:07:25 UTC 2022
Build Host : iox-ucs-002
Workspace : /auto/srcarchive12/prod/7.7.1/ncs540l/ws
Version : 7.7.1
Label : 7.7.1-iso
cisco NCS540L (C3708 @ 1.70GHz)
cisco N540X-16Z4G8Q2C-A (C3708 @ 1.70GHz) processor with 8GB of memory
R1-EVERGLIDE uptime is 5 hours, 23 minutes
Cisco NCS 540 System with 16x10G+4x1GCu+8x25G+2x100G AC Chassis
Log in to the router and enter the show version command on the N540X-8Z16G-SYS-A/D, and N540X-6Z18G-SYS-A/D variants:
RP/0/RP0/CPU0:Router# show version
Cisco IOS XR Software, Version 7.7.1 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Mon Jul 25 06:07:25 UTC 2022
Build Host : iox-ucs-004
Workspace : /auto/srcarchive12/prod/7.7.1/ncs540l-aarch64/ws
Version : 7.7.1
Label : 7.7.1-iso
cisco NCS540L
cisco N540X-6Z18G-SYS-D processor with 8GB of memory
R81-BEAGLE uptime is 6 hours, 23 minutes
Cisco NCS 540 Series Fixed Router 18x1G, 6x1/10G, DC
Log in to the router and enter the show version command on the N540-24Q8L2DD-SYS variant:
RP/0/RP0/CPU0:Router# show version
Cisco IOS XR Software, Version 7.7.1 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Mon Jul 25 06:07:25 UTC 2022
Build Host : iox-ucs-002
Workspace : /auto/srcarchive12/prod/7.7.1/ncs540l/ws
Version : 7.7.1
Label : 7.7.1-iso
cisco NCS540L (D1519 @ 1.50GHz)
cisco N540-24Q8L2DD-SYS (D1519 @ 1.50GHz) processor with 16GB of memory
R14-ARCHES uptime is 5 hours, 53 minutes
Cisco NCS540 Series, Fixed Router 2x400G, 8x50G, 24x25G Chassis
Log in to the router and enter the show version command on the N540-FH-AGG-SYS variant:
RP/0/RP0/CPU0:Router# show version
Cisco IOS XR Software, Version 7.7.1 LNT
Copyright (c) 2013-2022 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Mon Jul 25 06:07:25 UTC 2022
Build Host : iox-ucs-002
Workspace : /auto/srcarchive12/prod/7.7.1/ncs540l/ws
Version : 7.7.1
Label : 7.7.1
cisco NCS540L (C3708 @ 1.70GHz)
cisco N540-FH-AGG-SYS (C3708 @ 1.70GHz) processor with 8GB of memory
CE7-Lion uptime is 6 minutes
Cisco NCS 540 FH System with 24xCPRI/25G/10G/TSN+4x100G
Determine Firmware Support
Usethe show command in EXEC mode to view the hardware components with their current FPD version and status. The status of the hardware must be “CURRENT”; Running and Programed version must be the same. The Golden FPDs with “NEED UPGD” can be ignored, the Golden FPDs are not upgradable.
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-24Z8Q2C-SYS, N540X-ACC-SYS, and N540-ACC-SYS variants:
RP/0/RP0/CPU0:Router# show fpd package
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-24Z8Q2C-M Bootloader(A) YES 1.16 1.16 0.0
CPU-IOFPGA(A) YES 0.10 0.10 0.0
MB-IOFPGA(A) YES 0.26 0.26 0.0
MB-MIFPGA YES 0.05 0.05 0.0
SATA-INTEL_240G(A) NO 1132.00 1132.00 0.0
SATA-INTEL_480G(A) NO 1132.00 1132.00 0.0
SATA-M500IT-MC(A) NO 3.00 3.00 0.0
SATA-M500IT-MU-A(A) NO 5.00 5.00 0.0
SATA-M500IT-MU-B(A) NO 4.00 4.00 0.0
SATA-M5100(A) NO 75.00 75.00 0.0
SATA-M600-MCT(A) NO 5.00 5.00 0.0
SATA-M600-MU(A) NO 6.00 6.00 0.0
SATA-Micron(A) NO 1.00 1.00 0.0
SATA-SMART-128G(A) NO 1241.00 1241.00 0.0
SSFP_E1F_0 NO 13.01 13.01 0.0
SSFP_E1F_1 NO 13.01 13.01 0.0
SSFP_E1F_10 NO 13.01 13.01 0.0
SSFP_E1F_11 NO 13.01 13.01 0.0
SSFP_E1F_12 NO 13.01 13.01 0.0
SSFP_E1F_13 NO 13.01 13.01 0.0
SSFP_E1F_14 NO 13.01 13.01 0.0
SSFP_E1F_15 NO 13.01 13.01 0.0
SSFP_E1F_16 NO 13.01 13.01 0.0
SSFP_E1F_17 NO 13.01 13.01 0.0
SSFP_E1F_18 NO 13.01 13.01 0.0
SSFP_E1F_19 NO 13.01 13.01 0.0
SSFP_E1F_2 NO 13.01 13.01 0.0
SSFP_E1F_20 NO 13.01 13.01 0.0
SSFP_E1F_21 NO 13.01 13.01 0.0
SSFP_E1F_22 NO 13.01 13.01 0.0
SSFP_E1F_23 NO 13.01 13.01 0.0
SSFP_E1F_24 NO 13.01 13.01 0.0
SSFP_E1F_25 NO 13.01 13.01 0.0
SSFP_E1F_26 NO 13.01 13.01 0.0
SSFP_E1F_27 NO 13.01 13.01 0.0
SSFP_E1F_28 NO 13.01 13.01 0.0
SSFP_E1F_29 NO 13.01 13.01 0.0
SSFP_E1F_3 NO 13.01 13.01 0.0
SSFP_E1F_30 NO 13.01 13.01 0.0
SSFP_E1F_31 NO 13.01 13.01 0.0
SSFP_E1F_4 NO 13.01 13.01 0.0
SSFP_E1F_5 NO 13.01 13.01 0.0
SSFP_E1F_6 NO 13.01 13.01 0.0
SSFP_E1F_7 NO 13.01 13.01 0.0
SSFP_E1F_8 NO 13.01 13.01 0.0
SSFP_E1F_9 NO 13.01 13.01 0.0
SSFP_OC3_STM1_0 NO 12.01 12.01 0.0
SSFP_OC3_STM1_1 NO 12.01 12.01 0.0
SSFP_OC3_STM1_10 NO 12.01 12.01 0.0
SSFP_OC3_STM1_11 NO 12.01 12.01 0.0
SSFP_OC3_STM1_12 NO 12.01 12.01 0.0
SSFP_OC3_STM1_13 NO 12.01 12.01 0.0
SSFP_OC3_STM1_14 NO 12.01 12.01 0.0
SSFP_OC3_STM1_15 NO 12.01 12.01 0.0
SSFP_OC3_STM1_16 NO 12.01 12.01 0.0
SSFP_OC3_STM1_17 NO 12.01 12.01 0.0
SSFP_OC3_STM1_18 NO 12.01 12.01 0.0
SSFP_OC3_STM1_19 NO 12.01 12.01 0.0
SSFP_OC3_STM1_2 NO 12.01 12.01 0.0
SSFP_OC3_STM1_20 NO 12.01 12.01 0.0
SSFP_OC3_STM1_21 NO 12.01 12.01 0.0
SSFP_OC3_STM1_22 NO 12.01 12.01 0.0
SSFP_OC3_STM1_23 NO 12.01 12.01 0.0
SSFP_OC3_STM1_24 NO 12.01 12.01 0.0
SSFP_OC3_STM1_25 NO 12.01 12.01 0.0
SSFP_OC3_STM1_26 NO 12.01 12.01 0.0
SSFP_OC3_STM1_27 NO 12.01 12.01 0.0
SSFP_OC3_STM1_28 NO 12.01 12.01 0.0
SSFP_OC3_STM1_29 NO 12.01 12.01 0.0
SSFP_OC3_STM1_3 NO 12.01 12.01 0.0
SSFP_OC3_STM1_30 NO 12.01 12.01 0.0
SSFP_OC3_STM1_31 NO 12.01 12.01 0.0
SSFP_OC3_STM1_4 NO 12.01 12.01 0.0
SSFP_OC3_STM1_5 NO 12.01 12.01 0.0
SSFP_OC3_STM1_6 NO 12.01 12.01 0.0
SSFP_OC3_STM1_7 NO 12.01 12.01 0.0
SSFP_OC3_STM1_8 NO 12.01 12.01 0.0
SSFP_OC3_STM1_9 NO 12.01 12.01 0.0
--------------------------------------------------------------------------------
N540-ACC-SYS Bootloader(A) YES 1.16 1.16 0.0
CPU-IOFPGA(A) YES 0.10 0.10 0.0
MB-IOFPGA(A) YES 0.26 0.26 0.0
MB-MIFPGA YES 0.05 0.05 0.0
SATA-INTEL_240G(A) NO 1132.00 1132.00 0.0
SATA-INTEL_480G(A) NO 1132.00 1132.00 0.0
SATA-M500IT-MC(A) NO 3.00 3.00 0.0
SATA-M500IT-MU-A(A) NO 5.00 5.00 0.0
SATA-M500IT-MU-B(A) NO 4.00 4.00 0.0
SATA-M5100(A) NO 75.00 75.00 0.0
SATA-M600-MCT(A) NO 5.00 5.00 0.0
SATA-M600-MU(A) NO 6.00 6.00 0.0
SATA-Micron(A) NO 1.00 1.00 0.0
SATA-SMART-128G(A) NO 1241.00 1241.00 0.0
SSFP_E1F_0 NO 13.01 13.01 0.0
SSFP_E1F_1 NO 13.01 13.01 0.0
SSFP_E1F_10 NO 13.01 13.01 0.0
SSFP_E1F_11 NO 13.01 13.01 0.0
SSFP_E1F_12 NO 13.01 13.01 0.0
SSFP_E1F_13 NO 13.01 13.01 0.0
SSFP_E1F_14 NO 13.01 13.01 0.0
SSFP_E1F_15 NO 13.01 13.01 0.0
SSFP_E1F_16 NO 13.01 13.01 0.0
SSFP_E1F_17 NO 13.01 13.01 0.0
SSFP_E1F_18 NO 13.01 13.01 0.0
SSFP_E1F_19 NO 13.01 13.01 0.0
SSFP_E1F_2 NO 13.01 13.01 0.0
SSFP_E1F_20 NO 13.01 13.01 0.0
SSFP_E1F_21 NO 13.01 13.01 0.0
SSFP_E1F_22 NO 13.01 13.01 0.0
SSFP_E1F_23 NO 13.01 13.01 0.0
SSFP_E1F_24 NO 13.01 13.01 0.0
SSFP_E1F_25 NO 13.01 13.01 0.0
SSFP_E1F_26 NO 13.01 13.01 0.0
SSFP_E1F_27 NO 13.01 13.01 0.0
SSFP_E1F_28 NO 13.01 13.01 0.0
SSFP_E1F_29 NO 13.01 13.01 0.0
SSFP_E1F_3 NO 13.01 13.01 0.0
SSFP_E1F_30 NO 13.01 13.01 0.0
SSFP_E1F_31 NO 13.01 13.01 0.0
SSFP_E1F_4 NO 13.01 13.01 0.0
SSFP_E1F_5 NO 13.01 13.01 0.0
SSFP_E1F_6 NO 13.01 13.01 0.0
SSFP_E1F_7 NO 13.01 13.01 0.0
SSFP_E1F_8 NO 13.01 13.01 0.0
SSFP_E1F_9 NO 13.01 13.01 0.0
SSFP_OC3_STM1_0 NO 12.01 12.01 0.0
SSFP_OC3_STM1_1 NO 12.01 12.01 0.0
SSFP_OC3_STM1_10 NO 12.01 12.01 0.0
SSFP_OC3_STM1_11 NO 12.01 12.01 0.0
SSFP_OC3_STM1_12 NO 12.01 12.01 0.0
SSFP_OC3_STM1_13 NO 12.01 12.01 0.0
SSFP_OC3_STM1_14 NO 12.01 12.01 0.0
SSFP_OC3_STM1_15 NO 12.01 12.01 0.0
SSFP_OC3_STM1_16 NO 12.01 12.01 0.0
SSFP_OC3_STM1_17 NO 12.01 12.01 0.0
SSFP_OC3_STM1_18 NO 12.01 12.01 0.0
SSFP_OC3_STM1_19 NO 12.01 12.01 0.0
SSFP_OC3_STM1_2 NO 12.01 12.01 0.0
SSFP_OC3_STM1_20 NO 12.01 12.01 0.0
SSFP_OC3_STM1_21 NO 12.01 12.01 0.0
SSFP_OC3_STM1_22 NO 12.01 12.01 0.0
SSFP_OC3_STM1_23 NO 12.01 12.01 0.0
SSFP_OC3_STM1_24 NO 12.01 12.01 0.0
SSFP_OC3_STM1_25 NO 12.01 12.01 0.0
SSFP_OC3_STM1_26 NO 12.01 12.01 0.0
SSFP_OC3_STM1_27 NO 12.01 12.01 0.0
SSFP_OC3_STM1_28 NO 12.01 12.01 0.0
SSFP_OC3_STM1_29 NO 12.01 12.01 0.0
SSFP_OC3_STM1_3 NO 12.01 12.01 0.0
SSFP_OC3_STM1_30 NO 12.01 12.01 0.0
SSFP_OC3_STM1_31 NO 12.01 12.01 0.0
SSFP_OC3_STM1_4 NO 12.01 12.01 0.0
SSFP_OC3_STM1_5 NO 12.01 12.01 0.0
SSFP_OC3_STM1_6 NO 12.01 12.01 0.0
SSFP_OC3_STM1_7 NO 12.01 12.01 0.0
SSFP_OC3_STM1_8 NO 12.01 12.01 0.0
SSFP_OC3_STM1_9 NO 12.01 12.01 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LIT-PriMCU-ACFW(A) NO 0.04 0.04 0.0
LIT-SecMCU-ACFW(A) NO 0.07 0.07 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LIT-PriMCU-DCFW(A) NO 0.04 0.04 0.0
LIT-SecMCU-DCFW(A) NO 0.06 0.06 0.0
SDG-PriMCU-DCFW(A) NO 1.03 1.03 0.0
SDG-SecMCU-DCFW(A) NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-X-24Z8Q2C-M Bootloader(A) YES 1.16 1.16 0.0
CPU-IOFPGA(A) YES 0.10 0.10 0.0
MB-IOFPGA(A) YES 0.26 0.26 0.0
MB-MIFPGA YES 0.05 0.05 0.0
SATA-INTEL_240G(A) NO 1132.00 1132.00 0.0
SATA-INTEL_480G(A) NO 1132.00 1132.00 0.0
SATA-M500IT-MC(A) NO 3.00 3.00 0.0
SATA-M500IT-MU-A(A) NO 5.00 5.00 0.0
SATA-M500IT-MU-B(A) NO 4.00 4.00 0.0
SATA-M5100(A) NO 75.00 75.00 0.0
SATA-M600-MCT(A) NO 5.00 5.00 0.0
SATA-M600-MU(A) NO 6.00 6.00 0.0
SATA-Micron(A) NO 1.00 1.00 0.0
SATA-SMART-128G(A) NO 1241.00 1241.00 0.0
SSFP_E1F_0 NO 13.01 13.01 0.0
SSFP_E1F_1 NO 13.01 13.01 0.0
SSFP_E1F_10 NO 13.01 13.01 0.0
SSFP_E1F_11 NO 13.01 13.01 0.0
SSFP_E1F_12 NO 13.01 13.01 0.0
SSFP_E1F_13 NO 13.01 13.01 0.0
SSFP_E1F_14 NO 13.01 13.01 0.0
SSFP_E1F_15 NO 13.01 13.01 0.0
SSFP_E1F_16 NO 13.01 13.01 0.0
SSFP_E1F_17 NO 13.01 13.01 0.0
SSFP_E1F_18 NO 13.01 13.01 0.0
SSFP_E1F_19 NO 13.01 13.01 0.0
SSFP_E1F_2 NO 13.01 13.01 0.0
SSFP_E1F_20 NO 13.01 13.01 0.0
SSFP_E1F_21 NO 13.01 13.01 0.0
SSFP_E1F_22 NO 13.01 13.01 0.0
SSFP_E1F_23 NO 13.01 13.01 0.0
SSFP_E1F_24 NO 13.01 13.01 0.0
SSFP_E1F_25 NO 13.01 13.01 0.0
SSFP_E1F_26 NO 13.01 13.01 0.0
SSFP_E1F_27 NO 13.01 13.01 0.0
SSFP_E1F_28 NO 13.01 13.01 0.0
SSFP_E1F_29 NO 13.01 13.01 0.0
SSFP_E1F_3 NO 13.01 13.01 0.0
SSFP_E1F_30 NO 13.01 13.01 0.0
SSFP_E1F_31 NO 13.01 13.01 0.0
SSFP_E1F_4 NO 13.01 13.01 0.0
SSFP_E1F_5 NO 13.01 13.01 0.0
SSFP_E1F_6 NO 13.01 13.01 0.0
SSFP_E1F_7 NO 13.01 13.01 0.0
SSFP_E1F_8 NO 13.01 13.01 0.0
SSFP_E1F_9 NO 13.01 13.01 0.0
SSFP_OC3_STM1_0 NO 12.01 12.01 0.0
SSFP_OC3_STM1_1 NO 12.01 12.01 0.0
SSFP_OC3_STM1_10 NO 12.01 12.01 0.0
SSFP_OC3_STM1_11 NO 12.01 12.01 0.0
SSFP_OC3_STM1_12 NO 12.01 12.01 0.0
SSFP_OC3_STM1_13 NO 12.01 12.01 0.0
SSFP_OC3_STM1_14 NO 12.01 12.01 0.0
SSFP_OC3_STM1_15 NO 12.01 12.01 0.0
SSFP_OC3_STM1_16 NO 12.01 12.01 0.0
SSFP_OC3_STM1_17 NO 12.01 12.01 0.0
SSFP_OC3_STM1_18 NO 12.01 12.01 0.0
SSFP_OC3_STM1_19 NO 12.01 12.01 0.0
SSFP_OC3_STM1_2 NO 12.01 12.01 0.0
SSFP_OC3_STM1_20 NO 12.01 12.01 0.0
SSFP_OC3_STM1_21 NO 12.01 12.01 0.0
SSFP_OC3_STM1_22 NO 12.01 12.01 0.0
SSFP_OC3_STM1_23 NO 12.01 12.01 0.0
SSFP_OC3_STM1_24 NO 12.01 12.01 0.0
SSFP_OC3_STM1_25 NO 12.01 12.01 0.0
SSFP_OC3_STM1_26 NO 12.01 12.01 0.0
SSFP_OC3_STM1_27 NO 12.01 12.01 0.0
SSFP_OC3_STM1_28 NO 12.01 12.01 0.0
SSFP_OC3_STM1_29 NO 12.01 12.01 0.0
SSFP_OC3_STM1_3 NO 12.01 12.01 0.0
SSFP_OC3_STM1_30 NO 12.01 12.01 0.0
SSFP_OC3_STM1_31 NO 12.01 12.01 0.0
SSFP_OC3_STM1_4 NO 12.01 12.01 0.0
SSFP_OC3_STM1_5 NO 12.01 12.01 0.0
SSFP_OC3_STM1_6 NO 12.01 12.01 0.0
SSFP_OC3_STM1_7 NO 12.01 12.01 0.0
SSFP_OC3_STM1_8 NO 12.01 12.01 0.0
SSFP_OC3_STM1_9 NO 12.01 12.01 0.0
--------------------------------------------------------------------------------
N540X-ACC-SYS Bootloader(A) YES 1.16 1.16 0.0
CPU-IOFPGA(A) YES 0.10 0.10 0.0
MB-IOFPGA(A) YES 0.26 0.26 0.0
MB-MIFPGA YES 0.05 0.05 0.0
SATA-INTEL_240G(A) NO 1132.00 1132.00 0.0
SATA-INTEL_480G(A) NO 1132.00 1132.00 0.0
SATA-M500IT-MC(A) NO 3.00 3.00 0.0
SATA-M500IT-MU-A(A) NO 5.00 5.00 0.0
SATA-M500IT-MU-B(A) NO 4.00 4.00 0.0
SATA-M5100(A) NO 75.00 75.00 0.0
SATA-M600-MCT(A) NO 5.00 5.00 0.0
SATA-M600-MU(A) NO 6.00 6.00 0.0
SATA-Micron(A) NO 1.00 1.00 0.0
SATA-SMART-128G(A) NO 1241.00 1241.00 0.0
SSFP_E1F_0 NO 13.01 13.01 0.0
SSFP_E1F_1 NO 13.01 13.01 0.0
SSFP_E1F_10 NO 13.01 13.01 0.0
SSFP_E1F_11 NO 13.01 13.01 0.0
SSFP_E1F_12 NO 13.01 13.01 0.0
SSFP_E1F_13 NO 13.01 13.01 0.0
SSFP_E1F_14 NO 13.01 13.01 0.0
SSFP_E1F_15 NO 13.01 13.01 0.0
SSFP_E1F_16 NO 13.01 13.01 0.0
SSFP_E1F_17 NO 13.01 13.01 0.0
SSFP_E1F_18 NO 13.01 13.01 0.0
SSFP_E1F_19 NO 13.01 13.01 0.0
SSFP_E1F_2 NO 13.01 13.01 0.0
SSFP_E1F_20 NO 13.01 13.01 0.0
SSFP_E1F_21 NO 13.01 13.01 0.0
SSFP_E1F_22 NO 13.01 13.01 0.0
SSFP_E1F_23 NO 13.01 13.01 0.0
SSFP_E1F_24 NO 13.01 13.01 0.0
SSFP_E1F_25 NO 13.01 13.01 0.0
SSFP_E1F_26 NO 13.01 13.01 0.0
SSFP_E1F_27 NO 13.01 13.01 0.0
SSFP_E1F_28 NO 13.01 13.01 0.0
SSFP_E1F_29 NO 13.01 13.01 0.0
SSFP_E1F_3 NO 13.01 13.01 0.0
SSFP_E1F_30 NO 13.01 13.01 0.0
SSFP_E1F_31 NO 13.01 13.01 0.0
SSFP_E1F_4 NO 13.01 13.01 0.0
SSFP_E1F_5 NO 13.01 13.01 0.0
SSFP_E1F_6 NO 13.01 13.01 0.0
SSFP_E1F_7 NO 13.01 13.01 0.0
SSFP_E1F_8 NO 13.01 13.01 0.0
SSFP_E1F_9 NO 13.01 13.01 0.0
SSFP_OC3_STM1_0 NO 12.01 12.01 0.0
SSFP_OC3_STM1_1 NO 12.01 12.01 0.0
SSFP_OC3_STM1_10 NO 12.01 12.01 0.0
SSFP_OC3_STM1_11 NO 12.01 12.01 0.0
SSFP_OC3_STM1_12 NO 12.01 12.01 0.0
SSFP_OC3_STM1_13 NO 12.01 12.01 0.0
SSFP_OC3_STM1_14 NO 12.01 12.01 0.0
SSFP_OC3_STM1_15 NO 12.01 12.01 0.0
SSFP_OC3_STM1_16 NO 12.01 12.01 0.0
SSFP_OC3_STM1_17 NO 12.01 12.01 0.0
SSFP_OC3_STM1_18 NO 12.01 12.01 0.0
SSFP_OC3_STM1_19 NO 12.01 12.01 0.0
SSFP_OC3_STM1_2 NO 12.01 12.01 0.0
SSFP_OC3_STM1_20 NO 12.01 12.01 0.0
SSFP_OC3_STM1_21 NO 12.01 12.01 0.0
SSFP_OC3_STM1_22 NO 12.01 12.01 0.0
SSFP_OC3_STM1_23 NO 12.01 12.01 0.0
SSFP_OC3_STM1_24 NO 12.01 12.01 0.0
SSFP_OC3_STM1_25 NO 12.01 12.01 0.0
SSFP_OC3_STM1_26 NO 12.01 12.01 0.0
SSFP_OC3_STM1_27 NO 12.01 12.01 0.0
SSFP_OC3_STM1_28 NO 12.01 12.01 0.0
SSFP_OC3_STM1_29 NO 12.01 12.01 0.0
SSFP_OC3_STM1_3 NO 12.01 12.01 0.0
SSFP_OC3_STM1_30 NO 12.01 12.01 0.0
SSFP_OC3_STM1_31 NO 12.01 12.01 0.0
SSFP_OC3_STM1_4 NO 12.01 12.01 0.0
SSFP_OC3_STM1_5 NO 12.01 12.01 0.0
SSFP_OC3_STM1_6 NO 12.01 12.01 0.0
SSFP_OC3_STM1_7 NO 12.01 12.01 0.0
SSFP_OC3_STM1_8 NO 12.01 12.01 0.0
SSFP_OC3_STM1_9 NO 12.01 12.01 0.0
RP/0/RP0/CPU0:Router# show hw-module fpd
Auto-upgrade:Enabled
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------------
0/RP0 N540-ACC-SYS 1.0 MB-MIFPGA CURRENT 0.05 0.05
0/RP0 N540-ACC-SYS 1.0 Bootloader CURRENT 1.16 1.16
0/RP0 N540-ACC-SYS 1.0 CPU-IOFPGA CURRENT 0.10 0.10
0/RP0 N540-ACC-SYS 1.0 MB-IOFPGA CURRENT 0.26 0.26
0/RP0 N540-ACC-SYS 1.0 SATA-M500IT-MU-B CURRENT 4.00 4.00
0/PM0 N540-PWR400-A SDG-PriMCU-ACFW NOT READY
0/PM0 N540-PWR400-A SDG-SecMCU-ACFW NOT READY
0/PM1 N540-PWR400-A 1.256 LIT-PriMCU-ACFW CURRENT 0.04 0.04
0/PM1 N540-PWR400-A 1.256 LIT-SecMCU-ACFW CURRENT 0.07 0.07
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-28Z4C-SYS-A/D, N540-12Z20G-SYS-A/D, N540X-12Z16G-SYS-A/D and N540X-16Z4G8Q2C-A/D variants:
RP/0/RP0/CPU0:Router#show fpd package
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-12Z20G-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-12Z20G-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-24Q8L2DD-SYS ADM-DBConfig NO 2.03 2.03 0.0
ADM-MBConfig NO 2.01 2.01 0.0
IoFpga YES 2.12 2.12 0.0
IoFpgaGolden YES 2.12 2.12 0.0
Primary-BIOS YES 4.05 4.05 0.0
StdbyFpga YES 2.59 2.59 0.0
StdbyFpgaGolden YES 2.56 2.39 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-FH-AGG-SYS ADM1_Config NO 1.02 1.02 1.0
ADM2_Config NO 1.02 1.02 1.0
DpFpgaCpri YES 0.22 0.22 0.0
DpFpgaEth YES 1.20 1.20 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-CSR-SYS ADM1_Config NO 0.09 0.09 0.0
ADM1_Config NO 1.01 1.01 2.0
ADM2_Config NO 0.09 0.09 0.0
ADM2_Config NO 1.01 1.01 2.0
DpFpga YES 0.21 0.21 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.02 1.02 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.03 1.03 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-A EM-PrimMCU NO 1.02 1.02 0.0
EM-SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-D EM-PrimMCU NO 1.03 1.03 0.0
EM-SecMCU NO 3.01 3.01 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
RP/0/RP0/CPU0:Router# show hw-module fpd
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 ADMConfig CURRENT 1.05 1.05 NOT REQ
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 IoFpga CURRENT 2.07 2.07 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 IoFpgaGolden B NEED UPGD 1.31 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 Primary-BIOS S CURRENT 1.41 1.41 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 StdbyFpga S CURRENT 0.40 0.40 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 StdbyFpgaGolden BS NEED UPGD 0.37 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 TamFw S CURRENT 4.11 4.11 0/RP0
0/RP0/CPU0 N540X-16Z4G8Q2C-A 1.0 TamFwGolden BS CURRENT 4.11 0/RP0
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540X-6Z18G-SYS-A/D, and N540X-8Z16G-SYS-A/D variants:
RP/0/RP0/CPU0:Router#show fpd package
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-6Z14S-SYS-D ADMConfig NO 5.03 5.03 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-4Z14G2Q-A ADMConfig NO 5.00 5.00 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-4Z14G2Q-D ADMConfig NO 5.00 5.00 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-6Z18G-SYS-A ADMConfig NO 5.00 5.00 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-6Z18G-SYS-D ADMConfig NO 5.00 5.00 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-8Z16G-SYS-A ADMConfig NO 5.00 5.00 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540X-8Z16G-SYS-D ADMConfig NO 5.00 5.00 0.0
BckUp-BootLoader YES 20.05 20.05 0.0
IoFpga YES 0.17 0.17 0.0
IoFpgaGolden YES 0.15 0.15 0.0
Prim-BootLoader YES 20.05 20.05 0.0
StdbyFpga YES 1.09 1.09 0.0
StdbyFpgaGolden YES 0.33 0.33 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
RP/0/RP0/CPU0:Router#show hw-module fpd
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 ADMConfig NEED UPGD 1.02 1.02 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 IoFpga CURRENT 0.17 0.17 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 IoFpgaGolden B CURRENT 0.15 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 Prim-BootLoader CURRENT 20.05 20.05 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 StdbyFpga S CURRENT 1.09 1.09 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 StdbyFpgaGolden BS NEED UPGD 0.00 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 TamFw S CURRENT 6.05 6.05 0/RP0
0/RP0/CPU0 N540X-6Z18G-SYS-D 0.2 TamFwGolden BS NEED UPGD 5.06 0/RP0
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-24Q8L2DD-SYS variant:
RP/0/RP0/CPU0:Router# show fpd package
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-12Z20G-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-12Z20G-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-24Q8L2DD-SYS ADM-DBConfig NO 2.03 2.03 0.0
ADM-MBConfig NO 2.01 2.01 0.0
IoFpga YES 2.12 2.12 0.0
IoFpgaGolden YES 2.12 2.12 0.0
Primary-BIOS YES 4.05 4.05 0.0
StdbyFpga YES 2.59 2.59 0.0
StdbyFpgaGolden YES 2.56 2.39 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-FH-AGG-SYS ADM1_Config NO 1.02 1.02 1.0
ADM2_Config NO 1.02 1.02 1.0
DpFpgaCpri YES 0.22 0.22 0.0
DpFpgaEth YES 1.20 1.20 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-CSR-SYS ADM1_Config NO 0.09 0.09 0.0
ADM1_Config NO 1.01 1.01 2.0
ADM2_Config NO 0.09 0.09 0.0
ADM2_Config NO 1.01 1.01 2.0
DpFpga YES 0.21 0.21 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.02 1.02 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.03 1.03 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-A EM-PrimMCU NO 1.02 1.02 0.0
EM-SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-D EM-PrimMCU NO 1.03 1.03 0.0
EM-SecMCU NO 3.01 3.01 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
RP/0/RP0/CPU0:Router# show hw-module fpd
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 ADM-DBConfig NEED UPGD 1.51 1.51 NOT REQ
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 ADM-MBConfig CURRENT 2.01 2.01 NOT REQ
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 IoFpga CURRENT 2.12 2.12 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 IoFpgaGolden B NEED UPGD 0.00 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 Primary-BIOS S CURRENT 4.05 4.05 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 StdbyFpga S CURRENT 2.59 2.59 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 StdbyFpgaGolden BS NEED UPGD 0.00 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 TamFw S CURRENT 6.05 6.05 0/RP0
0/RP0/CPU0 N540-24Q8L2DD-SYS 2.0 TamFwGolden BS NEED UPGD 0.00 0/RP0
Log in to the router and enter the show fpd package and show hw-module fpd commands on the Cisco N540-FH-AGG-SYS variant:
RP/0/RP0/CPU0:Router# show fpd package
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
N540-12Z20G-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-12Z20G-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-24Q8L2DD-SYS ADM-DBConfig NO 2.03 2.03 0.0
ADM-MBConfig NO 2.01 2.01 0.0
IoFpga YES 2.12 2.12 0.0
IoFpgaGolden YES 2.12 2.12 0.0
Primary-BIOS YES 4.05 4.05 0.0
StdbyFpga YES 2.59 2.59 0.0
StdbyFpgaGolden YES 2.56 2.39 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-28Z4C-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540-FH-AGG-SYS ADM1_Config NO 1.02 1.02 1.0
ADM2_Config NO 1.02 1.02 1.0
DpFpgaCpri YES 0.22 0.22 0.0
DpFpgaEth YES 1.20 1.20 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-FH-CSR-SYS ADM1_Config NO 0.09 0.09 0.0
ADM1_Config NO 1.01 1.01 2.0
ADM2_Config NO 0.09 0.09 0.0
ADM2_Config NO 1.01 1.01 2.0
DpFpga YES 0.21 0.21 0.0
IoFpga YES 1.30 1.30 0.0
IoFpgaGolden YES 1.30 1.30 0.0
Primary-BIOS YES 1.33 1.33 0.0
StdbyFpga YES 0.46 0.46 0.0
StdbyFpgaGolden YES 0.46 0.46 0.0
TamFw YES 6.05 6.05 0.0
TamFwGolden YES 6.05 6.05 0.0
--------------------------------------------------------------------------------
N540-PWR400-A LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.02 1.02 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR400-D LI-PrimMCU NO 0.04 0.04 0.0
LI-SecMCU NO 0.06 0.06 0.0
PrimMCU NO 1.03 1.03 0.0
SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-A EM-PrimMCU NO 1.02 1.02 0.0
EM-SecMCU NO 1.03 1.03 0.0
--------------------------------------------------------------------------------
N540-PWR750-D EM-PrimMCU NO 1.03 1.03 0.0
EM-SecMCU NO 3.01 3.01 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-12Z16G-SYS-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z4G8Q2C-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-A ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
--------------------------------------------------------------------------------
N540X-16Z8Q2C-D ADMConfig NO 1.05 1.05 0.0
IoFpga YES 2.07 2.07 0.0
IoFpgaGolden YES 2.07 2.03 0.0
Primary-BIOS YES 1.41 1.41 0.0
StdbyFpga YES 0.40 0.40 0.0
StdbyFpgaGolden YES 0.40 0.40 0.0
TamFw YES 4.11 4.11 0.0
TamFwGolden YES 4.11 4.11 0.0
RP/0/RP0/CPU0:Router# show hw-module fpd
Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure
FPD Versions
==============
Location Card type HWver FPD device ATR Status Running Programd Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 ADM1_Config NEED UPGD 0.91 0.91 NOT REQ
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 ADM2_Config NEED UPGD 0.91 0.91 NOT REQ
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 DpFpgaCpri NOT READY 0.20 N/A
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 DpFpgaEth CURRENT 1.20 1.20 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 IoFpga CURRENT 1.30 1.30 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 IoFPgaGolden B NEED UPGD 1.23 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 Primary-BIOS S CURRENT 1.33 1.33 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 StdbyFpga S CURRENT 0.46 0.46 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 StdbyFpgaGolden BS NEED UPGD 0.00 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 TamFw S CURRENT 6.05 6.05 0/RP0
0/RP0/CPU0 N540-FH-AGG-SYS 1.0 TamFwGolden BS NEED UPGD 0.26 0/RP0
0/PM1 N540-PWR750-A 0.0 PrimMCU NOT READY 1.02 1.02 N/A
0/PM1 N540-PWR750-A 0.0 SecMCU NOT READY 1.03 1.03 N/A
Important Notes
Supported Transceiver Modules
For more information on the supported transceiver modules, see Transceiver Module Group (TMG) Compatibility Matrix. In the Begin your Search search box, enter the keyword NCS540 and click Enter.
Upgrading Cisco IOS XR Software
Cisco IOS XR Software is installed and activated from modular packages, allowing specific features or software patches to be installed, upgraded, or downgraded without affecting unrelated processes.
The upgrade document for N540-24Z8Q2C-SYS, N540X-ACC-SYS, and N540-ACC-SYS variants is available along with the software image in NCS540-docs-7.7.1.tar file.
The upgrade document for N540-28Z4C-SYS-A/D, N540-12Z20G-SYS-A/D, N540X-12Z16G-SYS-A/D, N540X-16Z4G8Q2C-A/D, N540-24Q8L2DD-SYS, N540-FH-AGG-SYS, and N540-FH-CSR-SYS variants is available along with the software image in NCS540l-docs-7.7.1.tar file.
The upgrade document for N540X-4Z14G2Q-A/D, N540X-8Z16G-SYS-A/D, and N540X-6Z18G-SYS-A/D variants is available along with the software image in NCS540l-aarch64-docs-7.7.1.tar file.
Note |
Quad configurations will be lost when you perform a software downgrade on Cisco NCS 540 Routers that support quad configurations from IOS XR Release 7.5.1 onwards to a release prior to IOS XR Release 7.5.1 due to a non-backward compatibility change. The lost configuration can be applied manually after the downgrade. |
Use user-class Option 'xr-config' Instead Of 'exr-config' To Provision ZTP
In Cisco IOS XR Release 7.3.1 and earlier, the system accepts the device sending user-class = "exr-config"; however starting Cisco IOS XR Release 7.3.2 and later, you must use only user-class = "xr-config".
In Cisco IOS XR Release 7.3.2 and later, use:
host cisco-rp0 {
hardware ethernet e4:c7:22:be:10:ba;
fixed-address 172.30.12.54;
if exists user-class and option user-class = "iPXE" {
filename = "http://172.30.0.22/boot.ipxe";
} elsif exists user-class and option user-class = "xr-config" {
filename = "http://172.30.0.22/scripts/cisco-rp0_ztp.sh";
}
}
Additional References
Supported MIBs
The Cisco NCS 5500 MIB support list is also applicable to the Cisco NCS 540 Series Routers. For the list of supported MIBs, see the Cisco NCS5500 MIB Support List.