About the Cisco Prime NAM 2400 Series Appliances
There are two models of the Cisco Prime NAM 2440 appliance (both are 2RU form-factor):
- Cisco Prime NAM 2440—This model receives collected data over up to four 10 GbE ports at a data rate of 10 Gb/s each, uses fiber-optic cables, and connects to the data collection devices with SFP+ connectors.
- Cisco Prime NAM 2420—This model receives collected data over up to two 10 GbE ports at a data rate of 10 Gb/s each, uses fiber-optic cables, and connects to the data collection devices with SFP+ connectors. The data ports also support 1GbE SFP modules.
The Cisco Prime NAM 2400 series appliances come preloaded with Cisco Prime Network Analysis Module (NAM) software and are contained in a standard shelf-rack enclosure.
The following sections describe:
Cisco Prime NAM 2400 Appliance Views and LEDs
Figure 1-1 Cisco Prime NAM 2400 Appliance Front View
1 |
Drive bays 1–24 (up to 24 2.5-inch drives) |
7 |
Temperature status LED |
2 |
Operations panel buttons and LEDs |
8 |
Power supply status LED |
3 |
Power button/LED |
9 |
Network link activity LED |
4 |
Unit Identification button/LED |
10 |
Pull-out asset tag |
5 |
System status LED |
11 |
KVM connector (used with KVM cable that provides two USB 2.0, one VGA, and one serial connector) |
6 |
Fan status LED |
|
|
For a description of the Cisco Prime NAM 2400 appliance front panel LEDs and their state definitions, see “Reading the LEDs” section.
Figure 1-2 Cisco Prime NAM 2400 Appliance Rear View
1 |
PCIe riser 1 (slots 1, 2, 3*) *Slot 3 not present in all versions. |
7 |
Serial connector (RJ-45) |
2 |
PCIe riser 2 (slots 4, 5, 6) |
8 |
Two embedded (on the motherboard) Intel i350 GbE Ethernet controller ports (LAN1, LAN2) |
3 |
Power supplies (DC power supplies shown) |
9 |
VGA video port (DB-15 connector) |
4 |
Modular LAN-on-motherboard (mLOM) card slot |
10 |
Rear Unit Identification button/LED |
5 |
USB 3.0 ports (two) |
11 |
Grounding-lug holes (for DC power supplies) |
6 |
1-Gbps dedicated management port |
|
|
Related Topics
Input/Output Ports and Connectors
The Cisco Prime NAM 2400 series appliances support the following ports on the rear of the appliance:
- NAM management port (LAN1, marked “1”)
Additional ports include:
- The video connector is not required for normal day-to-day operation of the NAM appliances.
- The built-in port labeled “M” is the Cisco Integrated Management Controller (CIMC) port.
Note You can either use a single connection on port "1" for both NAM management and CIMC or use port "1" for NAM management and port "M" for CIMC to connect them to different switches.
The Cisco Prime NAM 2400 series appliances use the following connector types:
Table 1-1 Cisco Prime NAM Series Connector Types
|
|
|
|
NAM2420-K9 |
2 |
1G SFP/10G SFP+ The data ports on the 2420 also support 1G SFP. |
Single-mode fiber or multi-mode fiber. For SFP cabling specifications, see Installing the GBIC, SFP, SFP+, and XFP Optical Modules in Cisco CPT and Cisco ONS Platforms, SFP and SFP+ Description and Specifications. |
NAM2440-K9 |
4 |
1G SFP/10G SFP+ |
Single-mode fiber, multi-mode fiber, or passive or Active TwinAx cables (except for 5M passive cable). For SFP+ cabling specifications, see Installing the GBIC, SFP, SFP+, and XFP Optical Modules in Cisco CPT and Cisco ONS Platforms, SFP and SFP+ Description and Specifications. |
NAM Management Port (LAN 1)
The Cisco Prime NAM 2400 series appliances use the LAN 1 port, an integrated Ethernet controller (10/100/1000 Mb/s), as the management port. When you connect this port to a gateway, you enable management and NAM application access to the Cisco Prime NAM 2400 series appliances.
Note Do not use the built-in port labeled “M”, which is the Cisco Integrated Management Controller (CIMC) port, as the management port; the LAN 1 port provides additional functionality.
Note We recommend that you use no less than a Category 5e (or better) unshielded twisted-pair (UTP) cable for the management port connection.
To access the Ethernet port, connect a Category 5e (or better) unshielded twisted-pair (UTP) cable to the RJ-45 connector on the back of the appliance. (See Table 1-2 ). The appliance comes with an Ethernet RJ-45-to-RJ-45 yellow cable.
Table 1-2 Ethernet Cabling Guidelines
|
|
10BASE-T |
EIA Categories 3, 4, or 5 UTP (2 or 4 pairs) up to 328 ft. (100 m) |
100BASE-TX |
EIA Category 5e (or better) UTP (2 pairs) up to 328 ft. (100 m) |
1000BASE-T |
EIA Category 6 (recommended), Category 5E or 5 UTP (or better) (2 pairs) up to 328 ft. (100 m) |
Serial (Console) Port Connector and Cable
The Cisco Prime NAM 2400 series appliances use the RJ-45 serial port connector, which is located on the back of the appliance, to connect a console terminal (an ASCII terminal or PC running terminal-emulation software).
Use the thin, flat, RJ-45-to-RJ-45 rollover cable that comes with the appliance to connect the console port to an ASCII terminal or a PC running terminal-emulation software.
If you do not want to use the serial RJ-45 in the back, the NAM appliance comes with a KVM connector that hooks to the front (see Figure 1-1). This connector splits off into two USB ports: a DB-9-male port and a DB15-female port.
Small Form-Factor Pluggable (SFP) Modules
The Cisco small form-factor pluggable (SFP) and SFP+ transceiver modules are hot-swappable input/output (I/O) devices that plug into module sockets. The transceiver connects the electrical circuitry of the module with the optical or copper network.
Related Topics
KVM Console
The KVM console is an interface accessible from the Cisco UCS Manager GUI or the KVM Launch Manager that emulates a direct KVM connection. The KVM console allows you to view the serial console remotely without any connection to a terminal server. It also provides the “Virtual Media” feature used for recovery/ISO install.
If you want to use the KVM console to access the NAM appliance, you must ensure that either the appliance or the service profile associated with the appliance is configured with a CIMC IP address. The KVM console uses the CIMC IP address assigned to an appliance or a service profile to identify and connect with the correct NAM appliance.
- If the management subnet you are connected to has a DHCP server deployed, the CIMC will automatically receive an IP address. This address will be displayed during initial bootup and can be seen from a serial console connection or a VGA screen.
- If the management subnet you are connected to does not have a DHCP server, you must enter a static IP address by entering the CIMC configuration setup during bootup. To do this, press <F8> during initial bootup. After the address is set, the CIMC GUI and ssh connections will be available.
For more information about the KVM console, see the Starting the KVM Console section in the Cisco UCS Manager GUI Configuration Guide.
AC Power Supplies
The Cisco Prime NAM 2400 series appliances are equipped with a wide input range AC power supply that supports both 110-V and 220-V.
For more information about the power supplies shipped with the Cisco Prime NAM 2400 series appliances:
|
|
NAM 2420 |
The Power Specifications section in the Cisco UCS C240 Server Installation and Service Guide. |
NAM 2440 |
The Power Specifications section in the Cisco UCS C240 Server Installation and Service Guide. |
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference
(EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029
There will not be any blanking panels for the power supplies but there will be blanking panels for the 16 disk configuration. The server has 24 disk slots, so with the 16 disk configuration, there will be 8 blanking panels.