Table Of Contents
Upgrading Cisco ONS 15454 Release 3.0 to 3.0.1 Using the TCC+ Card
Introduction
Upgrade Requirements
CTC Workstation Requirements
IP Address Caveat
LAN Caveat
Verification of Duplex Common Control
Telnet Session
AIP Verification
Back Up the Database
Upgrade the Software
Download
Before You Activate
BLSR Nodes Only
All Nodes
Activate the New Load
Delete Cached Jar Files
BLSR Lockout Removal
Date/Time Setting
Spare TCC+ Units
XC to XCVT Card Upgrade
Revert to Previous Load
BLSR Lockout
Revert to Protect Load
Manually Restore the Database
BLSR Lockout Removal
Upgrading Cisco ONS 15454 Release 3.0 to 3.0.1 Using the TCC+ Card
Introduction
This document explains how to upgrade Cisco ONS 15454's Cisco Transport Controller (CTC) software from Release 3.0 to Release 3.0.1 using the Timing, Communications, and Control + (TCC+) card.
Before beginning, write down the following information about your site; the data will be useful during and after the upgrade: Date, Street Address, Site Phone Number, and Dial Up Number.
Caution
Read each procedure before you begin the upgrade.
Caution
This procedure is only supported for Release 3.0. If you wish to upgrade from Releases 2.2.0 - 2.2.2, use the procedures in
Upgrading Cisco ONS 15454 Release 2.2.x to 3.0.1 Using the TCC+ Card. If you wish to upgrade from a release prior to Release 2.2.0, you must call the Technical Assistance Center (TAC) at 877 323-7368 for assistance.
Upgrade Requirements
This section contains critical information that you must read before the upgrade process.
Read the Release Notes for Cisco ONS 15454 Release 3.0.1 before you begin this upgrade procedure.
CTC Workstation Requirements
Before upgrading the workstation to run CTC Release 3.0.1, verify all PC or UNIX workstation hardware and software requirements.
•A Windows or Unix workstation:
–IBM-compatible PC with a 486 or higher processor, CD-ROM drive, and 128 MB RAM running Windows 95, Windows 98, Windows 2000, or Windows NT
–UNIX workstation running Solaris
•Browser software (select one):
–Netscape Navigator 4.73 or higher (Netscape Navigator is included on the ONS 15454 software CD shipped with the node.)
–Netscape Communicator 4.61 or higher
–Internet Explorer 4.0 Service Pack 2 or higher
•The Java Policy File and Java Runtime Environment (JRE) file, Release 1.2.2_005 or later (1.3 is included on the ONS 15454 software CD)
Note If you upgrade to JRE 1.3.0, you will no longer be able to log into an ONS 15454 running Release 2.2.1 or prior, or an ONS 15327 running release 1.0.0. If you must later revert to a release that requires a previous version of the JRE, you will then have to reinstall Java and delete the jar files from your workstation's user "temp" directory after reverting all of the nodes in the network. If you are currently running a release that is also compatible with JRE 1.3, or if you retain your JRE 1.2.2 installation, the extra steps are not necessary.
IP Address Caveat
Disable all other Ethernet devices (such as a dial-up adapter) on the workstation that runs CTC.
If you have multiple IP addresses on your workstation, you should remove them; you cannot install CTC Release 3.0.1 if multiple IP addresses are configured.
LAN Caveat
If you have multiple ONS 15454 nodes configured in the same IP subnet, only one can be connected to a router. Otherwise, the remaining nodes might be unreachable. Refer to the Cisco ONS 15454 Installation and Operations Guide, Release 3.0.0 for LAN-connection suggestions.
Verification of Duplex Common Control
You must now use CTC to check for duplex common control cards.
Step 1 Log into the node.
Step 2 Ensure that slots 7, 8, 10, and 11 have cards installed. Release 3.0 does not support simplex operation.
Step 3 Repeat Steps 1 and 2 at every node in the network.
Telnet Session
Make sure all active telnet sessions to any node in the network are closed.
AIP Verification
If any of your nodes have an AIP board with the part number 67-11-00015, the board must be replaced. Perform the following steps to ensure that all of your AIP boards are good.
Step 1 Look at the back of your ONS 15454 node and locate the green board with "AIP" stamped into the right hand side (the writing will be sideways as you face the board).
Step 2 Locate the sticker with the part number. The number should be preceded by "P/N" on the sticker.
Note If there is no sticker with a part number, the number may be stamped into the board itself. If you cannot find the part number, you will need to contact the Technical Assistance Center (TAC) at 877 323-7368 for assistance.
Step 3 If the part number is any number other than 67-11-00015, go to the next node and start from Step 1 again.
Step 4 If the part number is 67-11-00015, contact the TAC at 877 323-7368 to request a Return Materials Authorization (RMA).
Step 5 Repeat Steps 1 - 4 for every node.
Back Up the Database
Before upgrading from Release 3.0 to Release 3.0.1 software, you must back up the current database for all nodes in the network.
Step 1 Log into CTC.
Step 2 From the node view, click the Maintenance > Database tabs.
Step 3 Click Backup.
Step 4 Save the database on the workstation's hard drive or on network storage. Use an appropriate file name with the file extension .db (for example, myDatabase.db).
Step 5 Click Save. A message appears indicating that the backup is complete.
Step 6 Click OK.
Step 7 Repeat Steps 1 - 6 for each node in the network.
Cisco recommends that you manually log critical information by either writing it down or printing screens where applicable. This step is optional after you have backed up the database. Use the following table to determine the information you should log; complete the table (or your own version) for every node in the network.
|
Item
|
Record data here (if applicable)
|
IP address of the node |
|
Node name |
|
Timing settings |
|
DCC connections; list all optical ports that have DCCs activated |
|
User IDs (List all, including at least one super user) |
|
Inventory; do a print screen from the inventory window |
|
Active TCC+ |
Slot 7 or Slot 11 (circle one) |
Active XC |
Slot 8 or Slot 10 (circle one) |
Network information; do a print screen from the Provisioning tab in the network view. |
|
Current configuration: BLSR, linear, etc. (do print screens as needed) |
|
List all protection groups in the system; do a print screen from the protection group window |
|
List alarms; do a print screen from the alarm window |
|
List circuits; do a print screen from the circuit window |
|
Upgrade the Software
After backing up the database and logging all of the required information, insert the Release 3.0.1 software CD into the workstation (or otherwise acquire access to the software) and begin the upgrade process. You must download and then activate the software.
Note Inserting the software CD activates the CTC Setup Wizard. You can use the setup wizard to install components or click Cancel to continue with the upgrade.
Caution
A traffic interruption of less than 60 ms on each circuit is possible during the activation, with Ethernet traffic disruption possibly lasting up to several minutes on each circuit.
Caution
Do not perform maintenance or provisioning activities during the activation process.
Note Starting with the node most directly connected to your workstation achieves the best download performance; however, in most networks it is usually safer to begin activation at the farthest node and proceed toward the one you are most directly connected to. This ensures that no node is at risk of being stranded if unforeseen circumstances cause the upgrade to fail. This issue is a matter of network administration policy.
There are two flash RAMs on the TCC+ card. An upgrade downloads the software to the backup RAM on both the backup and active TCC+ cards. The download procedure does not affect traffic because the active software continues to run at the primary RAM location; therefore, you can download the software at any time.
Download
Step 1 Check all nodes in the ring for existing alarms. Resolve any outstanding alarms before proceeding.
Step 2 After checking and resolving alarms on all nodes, download the software to each node.
Note During the software download process, the SWFTDWN alarm indicates that the software download is taking place. The alarm is normal and clears when the download is complete.
Step 3 From the CTC node view, click the Maintenance > Software tabs.
Step 4 Click Download. The Download Selection dialog box opens.
Step 5 Browse to locate the software files on the ONS 15454 System Software CD (or on your hard drive, if you are working from a local copy).
Step 6 Open the "Cisco15454" folder.
Step 7 Select the file with the ".pkg" extension and click Open.
Step 8 In the list of compatible nodes, select the checkboxes for all nodes you are downloading the software to.
Note Cisco advises that you limit concurrent software downloads to 3 nodes at once.
Step 9 Click OK. The Download Status column monitors the progress of the download.
Caution
Do not close CTC during the upgrade. Closing CTC will abort the upgrade process.
Note The software download process can take 30 minutes or more per node.
Before You Activate
BLSR Nodes Only
If the node is in a bidirectional line switched ring (BLSR) configuration, you must perform a span lockout at each node before activating the software for Release 3.0.1. Follow this procedure to perform a span lockout on a BLSR using CTC Release 3.0.
Note During the lockout, BLSR spans will not be protected. Be sure to remove the lockout after activating all nodes in the ring.
Note To prevent ring or span switching, perform the lockout on both the east and west spans of each node.
Step 1 Click the Maintenance > Ring tabs.
Step 2 For each of the BLSR trunk cards (OC-12 or OC-48), go to the row in the table for that card and perform the following steps:
a. Click the East Switch column to show the pull-down menu.
b. From the menu options, choose Span Lockout.
c. Click the West Switch column to show the pull-down menu.
d. From the menu options, choose Span Lockout.
e. Click Apply to activate the command.
Step 3 Repeat Step 2 at each node in the ring.
Note Ignore any Default K alarm or alarms that occur on the protect STS timeslots during this lockout period.
Note Leave the BLSR in the lockout state until you have finished activating all nodes.
All Nodes
Perform the following steps for all nodes in the network.
Step 1 Make sure all cards that are part of a protection group (1:1 and 1:N) are active on the working card of that protection group and that no protection switches are occurring. In other words, make sure protect cards are in standby before proceeding.
Step 2 To ensure database synchronization, run the memAudit utility:
a. Close all active telnet connections to the ONS 15454.
b. Copy the memAudit.exe from the ONS 15454 software CD or the following Cisco.com web page to a folder on your hard drive:
http://www.cisco.com/cgi-bin/tablebuild.pl/ons15454
c. In a command window, change the prompt to the folder where the memAudit.exe is located.
d. At the prompt, type the following command:
memAudit <nodename or IP address>
Note Optional parameters exist for the memAudit command. For more information about the memAudit utility, view the memAudit_readme.htm file on the CD or Cisco.com web page.
Activate the New Load
Log into and activate each node in the network using the following procedure.
Note Make sure all cards that are part of a protection group (1:1 and 1:N) are active on the working card of that protection group and that no protection switches are occurring. In other words, make sure that the protect cards are in standby before proceeding.
Step 1 Log into a node.
Step 2 Verify that the node has no new alarms. If alarms exist, clear them before proceeding.
Step 3 From the CTC node view, click the Maintenance > Software tabs.
Step 4 Verify that the protect version is 3.0.1.
Step 5 Click Activate. The Activate dialog box appears with a warning message.
Step 6 Click Yes to proceed with the activation. The "Activation Successful" message appears when the software is successfully activated.
Step 7 Click OK to begin the node rebooting process.
Step 8 After activating the node, wait until the software upgrade reboot finishes at that node before continuing. A system reboot (SYSBOOT) alarm is raised while activation is in progress. Once all cards have reset, this alarm clears.
Each card in the node reboots, beginning with the standby TCC+. Once the standby TCC+ is fully activated and fully rebooted, it becomes the active TCC+ and the other TCC+ reboots. When the TCC+s are finished, the XC/XCVT in Slot 8 reboots, and then the XC/XCVT in Slot 10 reboots. Next, the Ethernet cards reset all at once, then the line cards boot consecutively from left to right. The whole process can take up to 30 minutes, depending on how many cards are installed. This process is service affecting, so Cisco recommends that you activate the new load during a maintenance window. TDM traffic can endure a hit of up to 50 ms. Expect Ethernet traffic to remain down from the time the TCC+s switch to the time all Ethernet cards have finished resetting. Once all the cards finish rebooting and all alarms clear, you can safely proceed to the next step. (If you are upgrading remotely and cannot see the nodes, wait for 30 minutes for the process to complete, then check to ensure all alarms have cleared before proceeding.)
Note Steps 10 to 12 are only necessary after upgrading the first node. For the remaining nodes, you will still be disconnected and removed to the network view during the node reboot, but after the reboot is complete, CTC will restore connectivity to the node.
Step 9 In CTC, choose File > Exit.
Step 10 In your browser window, click "Delete CTC Cache."
Note It might also be necessary to delete cache files from your browser's directory, or from the "temp" directory on your MS Windows workstation. If you have trouble reconnecting to CTC, refer the "Delete Cached Jar Files" section.
Step 11 Reconnect to CTC using the IP address from Step 2 (if the IP address is still in the browser location bar you can simply hold down the shift key and click the browser's Reload/Refresh button). The new CTC applet for Release 3.0.1 uploads. Because CTC 3.0.1 is backwardly compatible with CTC Release 3.0, it affords you network visibility while you are upgrading.
Note Only activate one node at a time.
Step 12 Log into each of the remaining nodes and perform the procedure to Activate the New Load. The activation must be performed for every node that is running software Release 3.0.x. Allow each node to finish (all alarms cleared for 10 minutes) before activating the next node.
Delete Cached Jar Files
When you upgrade or revert to a different CTC software load, you must reload CTC to your browser. In most cases, you can do this by simply clicking "Delete CTC Cache" in your browser window; however, in some circumstances, you may need to delete cache files from your browser's directory, or from the "temp" directory on your MS Windows workstation. If you have trouble reconnecting to CTC after upgrading or reverting, follow the procedures below.
Step 1 Delete cache files from your browser directory.
In Netscape:
a. Choose Edit > Preferences > Advanced > Cache.
b. Click Clear Memory Cache.
c. Click OK.
d. Click Clear Disk Cache.
e. Click OK twice.
In Microsoft Internet Explorer:
a. Choose Tools > Internet Options > General.
b. Choose Delete Files.
c. Select the Delete all offline content checkbox.
d. Click OK twice.
Step 2 Close your browser.
Step 3 Delete cached files from your workstation (Windows systems only).
a. In your Windows start menu, choose Settings > Control Panel > System > Advanced.
b. Click Environment Variables. This will show you a list of user variables and a list of system variables.
c. In the list of user variables, look for the variable "TEMP." The value associated with this variable is the path to your temporary directory where jar files are stored.
d. Open the "TEMP" directory located in the path you just looked up.
e. Select View > Details.
f. Select and delete all files with "jar" in either the name or type field.
Step 4 Reopen your browser. You should now be able to connect to CTC.
BLSR Lockout Removal
Release the span lockouts on all BLSR nodes after the new software load is activated on all nodes. The following procedure restores a BLSR using Release 3.0.1.
Step 1 In CTC node view, click the Maintenance > Ring tabs.
Step 2 For each of the BLSR trunk cards (OC-12 or OC-48), go to the row in the table for that card and perform the following steps:
a. Click in the West Switch column to show the pull-down menu.
b. From the menu options, choose Clear.
c. Click Apply to activate the command.
Note When removing a lockout, be sure to apply your changes after each time you choose the Clear option. If you try to select Clear for more than one lockout at a time, you risk traffic loss on the first ring switch.
d. In the same row, click in the East Switch column to show the pull-down menu.
e. From the menu options, choose Clear.
f. Click Apply to activate the command.
Step 3 You might need to accept a new ring map to clear Default K byte or Node ID mismatch alarms. From the Provisioning > Ring tabs, click the Ring Map button. If a new ring map exists, click Accept.
Date/Time Setting
If you are not using SNTP, the upgrade procedure can cause the Date/Time setting to change.
Step 1 In CTC node view, click the Provisioning > General tabs.
Step 2 Set the correct date and time, then click Apply.
Step 3 Repeat Steps 1 and 2 for each remaining node.
Spare TCC+ Units
All spare TCC+ units should be upgraded to CTC Release 3.0.1.
To upgrade a spare TCC+, place it in the standby slot of a node running Release 3.0.1. The card will upgrade automatically from the active TCC+.
Note This procedure could take up to 30 minutes per TCC+ card. During this time, the LEDs on the upgrading card will flash alternately between "fail" and "standby."
XC to XCVT Card Upgrade
If you need to upgrade your XC cards to XCVT, please refer to the user documentation for the software you are currently running.
Revert to Previous Load
Before upgrading from Release 3.0 to Release 3.0.1 software, you must back up the current database at all nodes in the network (this is part of the "Back Up the Database" section). Cisco recommends that you record or export all critical information to your hard drive. If you need to revert to the backup database, use the following procedures.
BLSR Lockout
If you have a BLSR provisioned, before beginning the revert you must perform a span lockout at each node. Follow the procedure in the "BLSR Lockout" section on page 6 to perform a span lockout on a BLSR using CTC Release 3.0.1.
Note Leave the BLSR in the lockout state until you have finished reverting all nodes.
Revert to Protect Load
Note To perform a supported (non service-affecting) revert from Release 3.0.1, the release you wish to revert to must have been working at the time you activated to Release 3.0.1 on that node. Also, a supported revert automatically restores the node configuration to its state at the time of the previous activation. Thus, any configuration changes made after activation will be lost when you revert the software.
Step 1 From the node view, click the Maintenance > Software tabs.
Step 2 Verify that the protect software displays 3.0.
Step 3 Click Revert. Revert activates the protect software and restores the database from the previous load. A dialog box asks you to confirm the choice.
Step 4 Click OK. This begins the revert and drops the connection to the node.
Step 5 After reverting the node, wait until the software revert finishes at that node before continuing.
Note Be patient. The system reboot might take up to 30 minutes to complete.
Step 6 Shut down your Netscape or Internet Explorer browser.
Step 7 Wait one minute before restoring another node.
Note If you upgraded to JRE 1.3.0, you cannot log into an ONS 15454 running Release 2.2.1 or prior (or an ONS 15327 running Release 1.0.0). If you are reverting to a release that required a previous version of JRE, you will need to reinstall Java and delete the jar files from your workstation's system "temp" directory after reverting all of the nodes in the network. If you are reverting to a release that also uses JRE 1.3, or if you retained your older version of JRE during the upgrade, this will not be an issue.
Step 8 After reverting all of the nodes in the network, restart the browser and log back into the last node that was reverted. This uploads the appropriate CTC applet for Release 3.0 to your workstation.
Manually Restore the Database
The revert procedure should have restored your Release 3.0 database completely; however, as a precaution, Cisco includes here the steps to restore the pre-upgrade database manually.
Caution
Do not perform these steps unless the software revert failed.
Caution
This process is service affecting and should be performed during a service window.
Step 1 From the CTC node view, click the Maintenance > Database tabs.
Step 2 Click Backup. The "Open..." dialog box appears.
Step 3 Select the previously-saved file and choose Open.
The database will be restored and the TCC+s will reboot.
Step 4 Once the TCC+s have rebooted, log back into CTC and verify that the database is restored.
Wait one minute before restoring the next node.
BLSR Lockout Removal
To restore BLSR protection you must clear the span lockouts on all BLSR nodes after reverting the software load and restoring the database on all nodes. Follow the procedure in the "BLSR Lockout Removal" section to restore a BLSR using Release 3.0.
This document is to be used in conjunction with the Release Notes for Cisco ONS 15454 Release 3.0.1 publication.
CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Follow Me Browsing, FormShare, iQ Net Readiness Scorecard, Networking Academy, and ScriptShare are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe, TeleRouter, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0303R)
Copyright © 2003, Cisco Systems, Inc.
All rights reserved.
Feedback