Note |
Explore the Content Hub, the all new portal that offers an enhanced product documentation experience.
Get started with the Content Hub at content.cisco.com to craft a personalized documentation experience. Do provide feedback about your experience with the Content Hub. |
What's New in Cisco IOS XR Release
Cisco is continuously enhancing the product with every release and this section covers a brief description of key features and enhancements. It also includes links to detailed documentation, where available.
Feature | Description |
---|---|
Configuration |
|
Performance monitoring parameters for the OTS and OTS OCH controllers in 10 second intervals are available. This new bucket for performance monitoring allows you to gather, store, and report performance data with higher granularity. Commands modified:
|
|
Grid mode configuration for the optical amplifier has been extended to support 75GHz spaced channels. You can optimize the optical spectrum and granularity using the gridless configuration. You can provision channels with arbitrary channel frequencies and channel widths. Up to 96 channels can be configured using the gridless configuration. Commands modified:
|
|
This feature allows you to create a fault profile for faults on the system or on the line card. Each fault profile can contain one or more faults with user-defined severities. Commands added:
|
|
LLDP is supported on the OSC management interface for point-to-point local link discovery through OSC channel. This helps you to gather information about the neighboring devices in the network. |
|
OTDR ML (Machine Learning) can be enabled on the OTDR card. When ML is enabled, the OTDR measurement shows more information about the events present on the fiber. |
|
Data Models |
|
NETCONF Support for READ, WRITE, and Execute or Administrative Commands. |
Support for IPv4 and IPv6 Ping test using the Cisco-IOS-XR-ping-act YANG model, instead of using CLI commands, is available. RPC (Remote Procedure Call) Request and Response messages are used to do the ping test, which is automated using scripts. This enables you to perform the ping test in a less time-consuming manner and to enhance network scalability. |
OC (Open Configuration) support for LLDP (Link Layer Discovery Protocol) on Management Port |
Open Configuration support for configuring LLDP on management port is available. RPC (Remote Procedure Call) Request and Response messages are used to configure LLDP on management port, which is automated using scripts. This makes the task, less time-consuming. |
Hardware |
|
A new passive device with PID NCS1K-MD-64-C (NCS 1000 64 channels Odd Multiplexer or Demultiplexer Patch Panel-C-band) is supported. |
Supported Packages and System Requirements
Release 7.3.1 Packages
Feature Set |
Filename |
Description |
Composite Package |
||
Cisco IOS XR Core Bundle + Manageability Package |
ncs1001-iosxr-px-k9-7.3.1.tar |
Contains required core packages, including operating system, Admin, Base, Forwarding, SNMP Agent, FPD, and Alarm Correlation and Netconf-yang, Telemetry, Extensible Markup Language (XML) Parser, HTTP server packages. |
Individually Installable Optional Packages |
||
Cisco IOS XR Security Package |
ncs1001-k9sec-1.0.0.0-r731.x86_64.rpm (part of ncs1k-iosxr-px-k9-7.3.1.tar) |
Support for Encryption, Decryption, IP Security (IPsec), Secure Shell (SSH), Secure Socket Layer (SSL), and Public-key infrastructure (PKI). |
See Install Packages.
System Requirements
Memory Configuration
At least 16 GB RAM
Determine Software Version
Log in to NCS 1001 and enter the show version command:
RP/0/RP0/CPU0:ios#show version
Mon Feb 28 15:52:01.424 UTC
Cisco IOS XR Software, Version 7.3.1
Copyright (c) 2013-2020 by Cisco Systems, Inc.
Build Information:
Built By : deenayak
Built On : Mon Jul 28 01:19:52 PST 2020
Built Host : iox-lnx-071
Workspace : /auto/srcarchive15/prod/7.3.1/ncs1001/ws
Version : 7.3.1
Location : /opt/cisco/XR/packages/
Label : 7.3.1
cisco NCS-1001 () processor
Note |
The output that is obtained by the show version command may be different from the preceding example. |
Determine Firmware Support
Log in to NCS 1001 and enter the show hw-module fpd command:
Use the show hw-module fpd command in EXEC mode to view the hardware components with their current FPD version and status. The status of the hardware must be CURRENT; Running and Programed version must be the same.
The following shows the output of show hw-module fpd command for NCS 1001 with EDFA (slot 1 and 3) and PSM (slot 2) of vendor 1.
RP/0/RP0/CPU0:ios#show hw-module fpd
Thu Jan 16 15:28:28.146 CEST
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
---------------------------------------------------------------------------------------------------
0/0 NCS1001-K9 0.1 Control_BKP B CURRENT 1.10
0/0 NCS1001-K9 0.1 Control_FPGA CURRENT 1.10 1.10
0/1 NCS1K-EDFA 0.0 FW_EDFAv1 CURRENT 1.56 1.56
0/2 NCS1K-PSM 0.0 FW_PSMv1 CURRENT 1.51 1.51
0/3 NCS1K-EDFA 0.0 FW_EDFAv1 CURRENT 1.56 1.56
0/RP0 NCS1K-CNTLR2 0.1 BIOS_Backup BS CURRENT 14.60 14.60
0/RP0 NCS1K-CNTLR2 0.1 BIOS_Primary S CURRENT 14.60 14.60
0/RP0 NCS1K-CNTLR2 0.1 Daisy_Duke_BKP BS CURRENT 0.20
0/RP0 NCS1K-CNTLR2 0.1 Daisy_Duke_FPGA S CURRENT 0.20 0.20
The following shows the output of show hw-module fpd command for NCS 1001 with EDFA (slot 1 and 3) and PSM (slot 2) of vendor 2.
RP/0/RP0/CPU0:150#show hw-module fpd
Thu Jan 16 15:28:31.146 CEST
FPD Versions
=================
Location Card type HWver FPD device ATR Status Running Programd
-----------------------------------------------------------------------------------
0/0 NCS1001-K9 0.1 Control_BKP B CURRENT 1.10
0/0 NCS1001-K9 0.1 Control_FPGA CURRENT 1.10 1.10
0/1 NCS1K-EDFA 0.0 FW_EDFAv2 CURRENT 0.43 0.43
0/2 NCS1K-PSM 0.0 FW_PSMv2 CURRENT 0.16 0.16
0/3 NCS1K-EDFA 0.0 FW_EDFAv2 CURRENT 0.43 0.43
0/RP0 NCS1K-CNTLR2 0.1 BIOS_Backup BS CURRENT 15.10 15.10
0/RP0 NCS1K-CNTLR2 0.1 BIOS_Primary S CURRENT 15.10 15.10
0/RP0 NCS1K-CNTLR2 0.1 Daisy_Duke_BKP BS CURRENT 0.20
0/RP0 NCS1K-CNTLR2 0.1 Daisy_Duke_FPGA S CURRENT 0.20 0.20
The following shows the output of show hw-module fpd command with the OTDR card in slot 1.
RP/0/RP0/CPU0:150#show hw-module fpd
Thu Jul 16 15:28:31.146 CEST
......
0/1 NCS1K-OTDR 0.0 FW_OTDR_p CURRENT 6.03 6.03
0/1 NCS1K-OTDR 0.0 FW_OTDR_s CURRENT 1.51 1.51
.....
The following shows the output of show hw-module fpd command entered from admin in case of AC PEM:
sysadmin-vm:0_RP0# show hw-module fpd
Fri Feb 5 15:36:47.562 UTC+00:00
FPD Versions
===============
Location Card type HWver FPD device ATR Status Run Programd
-------------------------------------------------------------------------------
……….
0/PM0 NCS1K-2KW-AC2 0.0 PO-PriMCU CURRENT 4.00 4.00
0/PM1 NCS1K-2KW-AC2 0.0 PO-PriMCU CURRENT 4.00 4.00
Then the following shows the output of show hw-module fpd command entered from admin in case of DC PEM :
sysadmin-vm:0_RP0# show hw-module fpd
Fri Feb 5 15:33:51.528 UTC+00:00
FPD Versions
===============
Location Card type HWver FPD device ATR Status Run Programd
-------------------------------------------------------------------------------
………
0/PM0 NCS1K-2KW-DC 0.2 PO-PriMCU CURRENT 1.14 1.14
0/PM1 NCS1K-2KW-DC 0.2 PO-PriMCU CURRENT 1.14 1.14
Other Important Information
Supported MIBs
The following MIBs are supported in NCS 1001:
-
CISCO-OPTICAL-OTS-MIB
-
CISCO-CONFIG-MAN-MIB
-
CISCO-FLASH-MIB
-
CISCO-ENTITY-REDUNDANCY-MIB
-
CISCO-SYSTEM-MIB
-
CISCO-ENTITY-ASSET-MIB
-
EVENT-MIB
-
DISMAN-EXPRESSION-MIB
-
CISCO-FTP-CLIENT-MIB
-
NOTIFICATION-LOG-MIB
-
CISCO-RF-MIB
-
CISCO-TCP-MIB
-
UDP-MIB
-
CISCO-OTN-IF-MIB
-
CISCO-ENHANCED-MEMPOOL-MIB
-
CISCO-PROCESS-MIB
-
CISCO-SYSLOG-MIB
-
ENTITY-MIB
-
CISCO-ENTITY-FRU-CONTROL-MIB
-
CISCO-IF-EXTENSION-MIB
-
RMON-MIB
-
CISCO-OPTICAL-MIB
-
CISCO-ENTITY-SENSOR-MIB