First Published: August 1, 2017

Last Updated: March 19, 2018

Overview of Cisco 1100 Series Integrated Services Routers

The Cisco 1100 Series Integrated Services Routers (ISR) are powerful fixed branch routers based on the Cisco IOS XE operating system. They are multi-core routers with separate core for data plane and control plane. There are two primary models with 8 LAN ports and 4 LAN ports. Features such as Smart Licensing, VDSL2 and ADSL2/2+, 802.11ac with Wave 2, 4G LTE-Advanced and 3G/4G LTE and LTEA Omnidirectional Dipole Antenna (LTE-ANTM-SMA-D) are supported on Cisco 1100 Series ISRs.


Note

Explore the Content Hub, the all new portal that offers an enhanced product documentation experience.

  • Use faceted search to locate content that is most relevant to you.

  • Create customized PDFs for ready reference.

  • Benefit from context-based recommendations.

Get started with the Content Hub at content.cisco.com to craft a personalized documentation experience.

Do provide feedback about your experience with the Content Hub.

The following table lists the router models that belong to the Cisco 1100 Series ISRs.

Cisco 1100 Series ISRs

C1111-8P

C1111-4P

C1111-8PLTEEA

C1111-4PLTEEA

C1111-8PLTELA

C1111-4PLTELA

C1111-8PWE

C1111-4PWE

C1111-8PWB

C1111-4PWB

C1111-8PWA

C1111-4PWA

C1111-8PWZ

C1111-4PWZ

C1111-8PWQ

C1111-4PWN

C1111-8PWN

C1111-4PWQ

C1111-8PWH

C1111-4PWH

C1111-8PWR

C1111-4PWR

C1111-8PWF

C1111-4PWF

C1111-8PLTEEAWE

C1111-4PWD

C1111-8PLTEEAWB

C1111-8PLTEEAWA

C1111-8PLTEEAWR

C1111-8PLTELAWZ

C1111-8PLTELAWN

C1111-8PLTELAWQ

C1111-8PLTELAWH

C1111-8PLTELAWF

C1111-8PLTELAWD

C1101-4P

C1101-4PLTEP

C1101-4PLTEPWX

C1116-4P

C1116-4PLTEEA

C1116-4PWE

C1116-4PLTEEAWE

C1117-4P

C1117-4PLTEEA

C1117-4PLTELA

C1117-4PWE

C1117-4PWA

C1117-4PWZ

C1117-4PM

C1117-4PMLTEEA

C1117-4PMWE

C1117-4PLTEEAWE

C1117-4PLTEEAWA

C1117-4PLTELAWZ

C1117-4PMLTEEAWE

System Requirements

The following are the minimum system requirements:

  • Memory: 4GB DDR4

  • Flash Storage: 4GB

Determining the Software Version

You can use the following commands to verify your software version:

  • For a consolidated package, use the show version command

  • For individual sub-packages, use the show version installed command

Installing a New Software Release

To install, obtain a Cisco IOS XE 16.x consolidated package (image) from Cisco.com. You can find software images at http://software.cisco.com/download/navigator.html. To run the router using individual sub-packages, you also need to first download the consolidated package and extract the individual sub-packages from a consolidated package.

For information about upgrading software, see the “Installing the Software” section in the Software Configuration Guide for the Cisco 1100 Series ISRs.

Upgrading the ROMMON Version on the Cisco 1100 Series ISR

For information about ROMMON and upgrading procedure, see the "ROMMON Overview and Basic Procedures” section in the Hardware Installation Guide for the Cisco 1100 Series Integrated Services Routers.

Feature Navigator

You can use Cisco Feature Navigator to find information about feature, platform, and software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on cisco.com is not required.

New Features and Important Notes for Cisco ISR 1000 Series, Cisco IOS XE Fuji 16.8.1

This section describes new features in Cisco IOS XE Fuji 16.8.1 that are supported on the Cisco 1000 Series ISRs.

New and Changed Information

New Software Features in Cisco ISR 1000 Series, Cisco IOS XE Fuji 16.8.1

The following are the new software features introduced in Cisco 1000 Series Integrated Service Routers for Cisco IOS XE Fuji 16.8.1 release:

G.Fast and VDSL2 35b Profile

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/routers/access/1100/software/configuration/xe-16-8/cisco_1100_series_swcfg_xe_16_8_x/cisco_1100_series_swcfg_xe_16_8_x_chapter_010101.html

Software Features for c1101 and c1109

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/routers/access/1100/software/configuration/xe-16-8/cisco_1100_series_swcfg_xe_16_8_x.html

Line command access class VRF awarenesss

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/xe-16-8/bba-xe-16-8-book/bba-vrf-aware-access-class-line.html

Umbrella Integration on ISR1100 series routers

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/routers/access/1100/software/configuration/xe-16-8/cisco_1100_series_swcfg_xe_16_8_x.html

VRRPv3 MIB based on RFC 6527

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/routers/access/1100/technical_reference/1100_mib_guide/isr1100_MIB.html

Model-Based AAA— Implements the NETCONF Access Control Model (NACM). NACM is a form of role-based access control (RBAC) specified in RFC 6536.

NETCONF Global Session Lock and Kill Session—Provides a global lock and the ability to kill non-responsive sessions in NETCONF. During a session conflict or client misuse of the global lock, NETCONF sessions can be monitored via the show netconf-yang sessions command, and non-responsive sessions can be cleared using the clear configuration lock command.

NETCONF and RESTCONF Debug commands—Commands for debugging were added.

NETCONF and RESTCONF IPv6 Support—Data model interfaces (DMIs) support the use of IPv6 protocol. DMI IPv6 support helps client applications to communicate with services that use IPv6 addresses. External facing interfaces will provide dual-stack support; both IPv4 and IPv6.

Configuring Security for VPNs with IPsec

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/routers/access/1100/software/configuration/xe-16-8/cisco_1100_series_swcfg_xe_16_8_x/sec-cfg-vpn-ipsec.html

YANG Data Models—For the list of Cisco IOS XE YANG models available with this release, navigate to https:/​/​github.com/​YangModels/​yang/​tree/​master/​vendor/​cisco/​xe/​1681.

Revision statements embedded in the YANG files indicate if there has been a model revision. The README.md file in the same github location highlights changes that have been made in the release.

For detailed information, see the following Cisco document:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/prog/configuration/168/b_168_programmability_cg/new_and_changed_information.html

Entering the Configuration Commands Manually

To enter the Cisco IOS commands manually, complete the following steps:

Before you begin

If you do not want to use the factory default configuration because the router already has a configuration, or for any other reason, you can use the procedure in this section to add each required command to the configuration.

Procedure

Step 1

Log on to the router through the Console port or through an Ethernet port.

Step 2

If you use the Console port, and no running configuration is present in the router, the Setup command Facility starts automatically, and displays the following text: 

--- System Configuration Dialog ---
 
Continue with configuration dialog? [yes/no]:

Enter no so that you can enter Cisco IOS CLI commands directly.

If the Setup Command Facility does not start automatically, a running configuration is present, and you should go to the next step.

Step 3

When the router displays the user EXEC mode prompt, enter the enable command, and the enable password, if one is configured, as shown in the following example: 

Router> enable
password password
Step 4

Enter config mode by entering the configure terminal command, as shown in the following example. 

Router> config terminal
Router(config)#
Step 5

Using the command syntax shown, create a user account with privilege level 15.
Step 6

If no router interface is configured with an IP address, configure one so that you can access the router over the network. The following example shows the interface Fast Ethernet 0 configured. 

Router(config)# int FastEthernet0
Router(config-if)# ip address 10.10.10.1 255.255.255.248
Router(config-if)# no shutdown
Router(config-if)# exit
Step 7

Configure the router as an http server for nonsecure communication, or as an https server for secure communication. To configure the router as an http server, enter the ip http server command shown in the example: 

Router(config)# ip http secure-server
Step 8

Configure the router for local authentication, by entering the ip http authentication local command, as shown in the example:

Router(config)# ip http authentication local
Step 9

Configure the vty lines for privilege level 15. For nonsecure access, enter the transport input telnet command. For secure access, enter the transport input telnet ssh command. An example of these commands follows: 

Router(config)# line vty 0 4
Router(config-line)# privilege level 15
Router(config-line)# login local
Router(config-line)# transport input telnet
Router(config-line)# transport output telnet
Router(config-line)# transport input telnet ssh
Router(config-line)# transport output telnet ssh
Router(config-line)# exit
Router(config)# line vty 5 15
Router(config-line)# privilege level 15
Router(config-line)# login local
Router(config-line)# transport input telnet
Router(config-line)# transport output telnet
Router(config-line)# transport input telnet ssh
Router(config-line)# transport output telnet ssh
Router(config-line)# end

Open and Resolved Bugs for Cisco IOS XE Fuji 16.8.x

This section provides information about the caveats in Cisco 1100 Series Integrated Services Routers and describe unexpected behavior. Severity 1 caveats are the most serious caveats. Severity 2 caveats are less serious. Severity 3 caveats are moderate caveats. This section includes severity 1, severity 2, and selected severity 3 caveats.

The open and resolved bugs for this release are accessible through the Cisco Bug Search Tool. This web-based tool provides you with access to the Cisco bug tracking system, which maintains information about bugs and vulnerabilities in this product and other Cisco hardware and software products. Within the Cisco Bug Search Tool, each bug is given a unique identifier (ID) with a pattern of CSCxxNNNNN, where x is any letter (a-z) and N is any number (0-9). The bug IDs are frequently referenced in Cisco documentation, such as Security Advisories, Field Notices and other Cisco support documents. Technical Assistance Center (TAC) engineers or other Cisco staff can also provide you with the ID for a specific bug. The Cisco Bug Search Tool enables you to filter the bugs so that you only see those in which you are interested.

In addition to being able to search for a specific bug ID, or for all bugs in a product and release, you can filter the open and/or resolved bugs by one or more of the following criteria:

  • Last modified date

  • Status, such as fixed (resolved) or open

  • Severity

  • Support cases

You can save searches that you perform frequently. You can also bookmark the URL for a search and email the URL for those search results.


Note
If the defect that you have requested cannot be displayed, this may be due to one or more of the following reasons: the defect number does not exist, the defect does not have a customer-visible description yet, or the defect has been marked Cisco Confidential.

We recommend that you view the field notices for the current release to determine whether your software or hardware platforms are affected. You can access the field notices from the following location:

Product Field Notice Summary

Using the Cisco Bug Search Tool

For more information about how to use the Cisco Bug Search Tool , including how to set email alerts for bugs and to save bugs and searches, see Bug Search Tool Help & FAQ.

Before You Begin


Note
You must have a Cisco.com account to log in and access the Cisco Bug Search Tool . If you do not have one, you can register for an account.

SUMMARY STEPS

  1. In your browser, navigate to the Cisco Bug Search Tool .
  2. If you are redirected to a Log In page, enter your registered Cisco.com username and password and then, click Log In.
  3. To search for a specific bug, enter the bug ID in the Search For field and press Enter.
  4. To search for bugs related to a specific software release, do the following:
  5. To see more content about a specific bug, you can do the following:
  6. To restrict the results of a search, choose from one or more of the following filters:

DETAILED STEPS

Step 1

In your browser, navigate to the Cisco Bug Search Tool .

Step 2

If you are redirected to a Log In page, enter your registered Cisco.com username and password and then, click Log In.

Step 3

To search for a specific bug, enter the bug ID in the Search For field and press Enter.

Step 4

To search for bugs related to a specific software release, do the following:

  1. In the Product field, choose Series/Model from the drop-down list and then enter the product name in the text field. If you begin to type the product name, the Cisco Bug Search Tool provides you with a drop-down list of the top ten matches. If you do not see this product listed, continue typing to narrow the search results.

  2. In the Releases field, enter the release for which you want to see bugs.

    The Cisco Bug Search Tool displays a preview of the results of your search below your search criteria.

Step 5

To see more content about a specific bug, you can do the following:

  • Mouse over a bug in the preview to display a pop-up with more information about that bug.

  • Click on the hyperlinked bug headline to open a page with the detailed bug information.
Step 6

To restrict the results of a search, choose from one or more of the following filters:

Filter

Description

Modified Date

A predefined date range, such as last week or last six months.

Status

A specific type of bug, such as open or fixed.

Severity

The bug severity level as defined by Cisco. For definitions of the bug severity levels, see Bug Search Tool Help & FAQ.

Rating

The rating assigned to the bug by users of the Cisco Bug Search Tool .

Support Cases

Whether a support case has been opened or not.

Your search results update when you choose a filter.

Open and Resolved Caveats in Cisco IOS XE Fuji 16.8.x

All open and resolved bugs for this release are available in the Cisco Bug Search Tool.

This section contains the following topics:

Resolved Caveats

Table 1. Resolved Caveats

Caveat ID Number

Description
Note 

There are no resolved caveats for this release.

Open Caveats

Table 2. Open Caveats

Caveat ID Number

Description
Note 

There are no open caveats in this release.

Related Documentation