Configuring Cisco EHWIC and 880G for 3G (EV-DO Rev A)
Available Languages
Table Of Contents
Configuring Cisco EHWIC and 880G for
3G (EV-DO Rev A)Modular Cisco ISR G2 Support for the EHWIC-3G-EVDO-x Cards
Product Descriptions and Supported Frequencies
New Features in the EVDO Versions of the EHWIC 3G Cards and C880 Series ISRs
Remotely Initiated Data Callback Using SMS
Overview of the EHWIC-3G-EVDO Cards
Overview of the C881G-B/S/V-K9 ISRs
C881G-B/S/V-K9 Front and Back Panels
Installing the C881G-B/S/V-K9 ISR
Overview of the C881GW-S/V-A-K9 ISRs
Installing the C881GW-S/V-A-K9 ISR
Supported Cisco Antennas and Cables
Configuring EHWIC-3G-EVDO-x Cards and C880G-x-K9 ISRs
3G Cellular WAN MIB Architecture
Configuration Prerequisites and Restrictions
Restrictions for Configuring 3G
Configuring the 3G Wireless Modular and Fixed Cisco ISRs
Modem Activation and Provisioning
Verifying Signal Strength and Service Availability
Configuring the Cellular Interface
Configuring Multiple Mobile IP Profiles
Configuring Data Dedicated Transmission Mode (DDTM)
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs
Example: Basic Cellular Interface Configuration
Example: Tunnel over Cellular Interface Configuration
Example: 3G Wireless Modem as Backup with NAT and IPSec
Example: Voice-Initiated Data Callback
cdma event connection-status mib-trap
cdma event modem-state mib-trap
cellular cdma activate oma-dm device config
cellular cdma activate oma-dm ni-alert
cellular cdma activate oma-dm prl-update
cellular cdma profile configure
Verifying Service Availability
Modem Troubleshooting Using the Diagnostic Port
Configuring Cisco EHWIC and 880G for
3G (EV-DO Rev A)
First Published: June 2011Last Updated: March 18, 2013
OL-24266-03This guide describes how to configure the Evolution-Data Optimized (EVDO) versions of 3G wireless Enhanced High-Speed WAN Interface Cards (EHWICs). The Cisco EHWIC-3G-EVDO-x cards — EHWIC-3G-EVDO-B (Bharat), EHWIC-3G-EVDO-S (Sprint), and EHWIC-3G-EVDO-V (Verizon) — are multiband, multiservice WAN cards for use over WCDMA Radio Access Networks (RAN).
This guide also describes the:
•
EVDO versions of the Cisco C881G Series Integrated Services Router (ISR): C881G-B-K9, C881G-S-K9, and C881G-V-K9. Each router contains an embedded multiband, multiservice WAN modem for use over WCDMA networks.
•
Contents
•
•
•
•
•
•
•
•
•
Modular Cisco ISR G2 Support for the EHWIC-3G-EVDO-x Cards
The EHWIC-3G-EVDO-x cards are supported on the following modular Cisco Integrated Service Routers Generation 2 (ISR G2) family of routers:
•
•
•
•
EHWIC-3G-EVDO-x Features
The EHWIC-3G-EVDO-x cards and C881G-x-K routers provide the following functionalities:
•
•
•
•
•
•
•
•
•
•
–
–
–
•
•
•
•
•
•
•
•
•
–
–
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Product Descriptions and Supported Frequencies
Table 1 shows the products discussed in this document and the frequencies they support.
New Features in the EVDO Versions of the EHWIC 3G Cards and C880 Series ISRs
The following are the new features available in EHWIC-3G-EVDO-x cards, C881G-B/S/V-K9 ISRs, and C881GW-S/V-A-K9 ISRs:
•
•
•
GPS
The GPS feature provides the following commands:
In the syntax of these commands, the unit parameter refers to:
•
•
These examples show how to enable GPS standalone and NMEA for EHWIC-3G-EVDO-x:
router(config)#controller cellular 0/0router(config-controller)#cdma gps mode standalone...controller Cellular 0/0cdma gps mode standalonerouter(config-controller)#cdma gps nmea...controller Cellular 0/0cdma gps mode standalonecdma gps nmea!These examples show how to display summary and detailed GPS data for C881G-x-K9:
router#show cellular 0 gpsGPS Info-------------GPS State: GPS enabledGPS Mode Configured: standaloneLatitude: 37 Deg 24 Min 59 Sec NorthLongitude: 121 Deg 55 Min 8 Sec WestTimestamp (GMT): Thu Jul 29 11:08:39 2010Fix type: 3D, Height: -6 mHeading: 408, Velocity Horiz: 3, Velocity Vert: 0Satellite Info----------------Satellite #13, elevation 75, azimuth 46, SNR 21...router#show cellular 0 gps detailGPS Info-------------GPS State: GPS enabledGPS Mode Configured: standaloneLatitude: 37 Deg 24 Min 59 Sec NorthLongitude: 121 Deg 55 Min 7 Sec WestTimestamp (GMT): Thu Jul 29 22:17:57 2010Fix type: 3D, Height: 12 mHeading: 0, Velocity Horiz: 0, Velocity Vert: 0...
Note
Note
SMS
This feature enables the router to send and receive SMS messages. This feature also enables the router to save and store the SMS messages on an FTP server.
Note
The SMS feature provides the following commands:
In the syntax of these commands, the unit parameter refers to:
•
•
Note
This example shows you how to send an SMS message (C881G-x-K9):
router#cellular 0 cdma sms send <phone number> "Test message"This example deletes all SMS messages (EHWIC-3G-EVDO-x):
router#cellular 0/1/0 cdma sms delete allThis example shows you how to display a summary of SMS messages (EHWIC-3G-EVDO-x):
router#cellular 0/1/0 cdma sms view summaryID FROM YY/MM/DD HR:MN:SC SIZE CONTENT0 4087993680 10/05/04 21:29:55 32 from John ...1 4087993680 10/05/04 21:52:45 32 from Jane ...2 4087993680 10/05/04 21:56:56 32 from Jake ...3 4087993680 10/05/04 21:56:58 32 from Tom ...4 4087993680 10/05/04 21:57:00 32 from Sam ...The following example sets FTP path to the SMS_archive directory on the FTP server at 192.168.1.3 (C881G-x-K9 and EHWIC-3G-EVDO-x):
router(config-controller)# gsm sms archive path ftp://username:password@192.168.1.3/SMS_archiveRemotely Initiated Data Callback Using SMS
This feature remotely brings up the cellular interface by sending SMS messages over CDMA networks.
The following example shows you how to configure this feature for the EHWIC:
chat-script cdma "" "atdt#777" TIMEOUT 60 "CONNECT"interface Loopback1ip address 1.1.1.1 255.255.255.0interface Cellular 0ip address negotiatedip virtual-reassembly inencapsulation pppload-interval 30dialer in-banddialer pool-member 1dialer idle-timeout 0no peer default ip addressasync mode interactiveppp chap hostname abc.cell.orgppp chap password 0 nopasswordppp ipcp dns requestrouting dynamicinterface Dialer1ip address negotiatedencapsulation pppdialer pool 1dialer idle-timeout 0dialer string cdmadialer caller 4081234567 callbackdialer-group 1ppp chap hostname abc.cell.orgppp chap password 0 nopasswordppp ipcp dns requestip route 0.0.0.0 0.0.0.0 Dialer1!access-list 1 permit anydialer-list 1 protocol ip list 1!line 3script dialer cdmaloginmodem InOutno exectransport input alltransport output all
Note
dialer caller 4081234567 callback). Replace this number with your own number. To test this example and bring the cellular link up, send an SMS message from your phone.
3G WWAN MIB Persistence
This feature allows you to retain 3G WWAN MIB object values and trap settings across router reloads.
Before configuring 3G WWAN MIB, you should perform some SNMP pre-configuration to avoid getting warning messages. The following is an example of SNMP pre-configuration:
snmp-server community public ROsnmp-server community private RWsnmp-server enable traps c3gThis example shows you the settings that you need to configure this feature for EHWIC-3G-EVDO-x:
controller Cellular 0/1cdma event rssi onset mib-trap 1xrttcdma event rssi onset mib-trap evdoRel0cdma event rssi onset mib-trap evdoRelAcdma event rssi onset threshold -84cdma event rssi abate mib-trap 1xrttcdma event rssi abate mib-trap evdoRel0cdma event rssi abate mib-trap evdoRelAcdma event rssi abate threshold -82cdma event ecio onset mib-trap 1xrttcdma event ecio onset mib-trap evdoRel0cdma event ecio onset mib-trap evdoRelAcdma event ecio onset threshold -7cdma event ecio abate mib-trap 1xrttcdma event ecio abate mib-trap evdoRel0cdma event ecio abate mib-trap evdoRelAcdma event ecio abate threshold -5cdma event temperature onset mib-trapcdma event temperature onset threshold 34cdma event temperature abate mib-trapcdma event temperature abate threshold 33cdma event modem-state mib-trap downcdma event modem-state mib-trap upcdma event service mib-trapcdma event network mib-trapcdma event connection-status mib-trap All-cdma!Overview of the EHWIC-3G-EVDO Cards
The Evolution-Data Optimized (EVDO) SKUs support the following multiple bands and services:
•
•
•
EHWIC-3G-EVDO-x is the Cisco part number for which the interface card is configured and x is a variable for carrier-specific versions.
The EHWIC-3G-EVDO versions currently available are:
•
•
•
Additional carrier-specific versions may also be available. See the onboard Product ID (PID) sticker to differentiate between released versions.
The EHWIC-3G-EVDO versions support diversity mode (dual antenna mode) in the antennas. Types of antennas include swivel-mounted dipole with extended base and ceiling-mounted antennas. The diversity mode requires two antennas located together and spaced a minimum of 7.5 in. (19 cm) for better RF reception.
Note
Figure 1 shows the front panel view of EHWIC-3G-EVDO.
Figure 1 EHWIC-3G-EVDO Front Panel
Mounting Screws
LEDs
Diagnostic Port
Diversity/GPS Antenna Connector
Main Antenna Connector
Note
Table 2 describes the functions of the LEDs of EHWIC-3G-EVDO. The LEDs provide a visual indication of your available services.
For information on how to install the EHWIC-3G-EVDO-x card in supported Cisco Access Routers, see Installing Cisco Interface Cards in Cisco Access Routers.
For information on how to connect the EHWIC-3G-EVDO-x card to your network, see Connecting Cisco EHWIC-3G-EVDO-x to the Network.
Overview of the C881G-B/S/V-K9 ISRs
The C881G-B-K9, C881G-S-K9, and C881G-V-K9 ISRs are members of the Cisco 880 series data routers. These routers provide integrated Virtual Private Network (VPN), 802.11b/g/n-compliant wireless Access Point (AP), 3G, and backup capabilities.
For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router Software Configuration Guide.
C881G-B/S/V-K9 Front and Back Panels
Figure 2 shows the front panel details of the C881G-B/S/V-K9 ISR. The front panel has only LEDs. All the ports are in the back panel.
Figure 2 Front Panel of the C881G-B/S/V-K9
Table 3 describes the LEDs for the C881G-B/S/V-K9 ISR. The LEDs provide a visual indication of the available services.
Figure 3 shows the back panel of the C881G-B/S/V-K9.
Figure 3 Back Panel of the C881G-B/S/V-K9
Installing the C881G-B/S/V-K9 ISR
To install the C881G-B/S/V-K9 ISR, follow the instructions in the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide. This guide describes the equipment and the procedures for installing the Cisco 860 series, 880 series, and 890 series ISRs.
However, the instructions for connecting the 3G card in the hardware installation guide do not apply to the C881G-B/S/V-K9 ISR because it does not have a slot for adding a 3G card. Instead, a 3G modem is embedded in the router.
Overview of the C881GW-S/V-A-K9 ISRs
The C881GW-S-A-K9 and C881GW-V-A-K9 ISRs are members of the Cisco 880G series data routers. These routers provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, 3G, and backup capabilities.
For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router Software Configuration Guide.
Front and Back Panels
Figure 4 shows the front panel details of the C881GW-S-A-K9 and C881GW-V-A-K9 ISRs. The front panel has LEDs only. All the ports are in the back panel.
Figure 4 Front Panel of the C881GW-S/V-A-K9 ISRs
Table 4 describes the LEDs of the C881GW-S-A-K9 and C881GW-V-A-K9 ISRs. The LEDs provide a visual indication of the available services.
Figure 5 shows the back panel details of the C881GW-S-A-K9 and C881GW-V-A-K9 ISRs.
Figure 5 Back Panel of the C881GW-S/V-A-K9 ISRs
Antenna (the antenna on the left is the main antenna and the one on the right is the DIV/GPS antenna)—connectorized wireless WAN (WWAN) omnidirectional dipole antenna (wireless models only)
Note
Primary WAN port—10/100 FE
Reset button
USB port
Power connector
3G USB diagnostic port
Kensington security slot
4-port 10/100 Ethernet switch
Power switch
Serial port—console or auxiliary
Installing the C881GW-S/V-A-K9 ISR
To install the C881GW-S-A-K9 and C881GW-V-A-K9 ISRs, follow the instructions in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide. This guide describes the equipment and the procedures for installing the Cisco 860 series, 880 series, and 890 series ISRs.
However, the instructions for connecting the 3G card in the hardware installation guide do not apply because these ISRs do not have a slot for adding a 3G card. Instead, a 3G modem is embedded in the router.
Supported Cisco Antennas and Cables
Table 5 lists the Cisco antennas that are supported for use with 3G EHWIC cards and C881G ISRs.
.
Table 5 Supported Cisco Antennas (3G EHWIC cards and C881G ISRs)
3G-ANTM1916-CM
High-Gain
Ceiling-Mount Omnidirectional1.5 dBi
(806-960 MHz)2.5 dBi
(1710-2170 MHz)Multiband ceiling-mounted omnidirectional antenna.
For more information, see Cisco Multiband In-Building Omnidirectional Ceiling-Mount Antenna (3G-ANTM1916-CM).
3G-ANTM1919D
Dipole Omnidirectional
0 dBi
(806-960 MHz)0 dBi
(1710-2170 MHz)This is the default antenna. Multiband dipole antenna. For more information, see Cisco Multiband Swivel-Mount Dipole Antenna (3G-ANTM1919D).
3G-AE015-R
(Antenna Extension)Extension Base
0.8-6.0 GHz
This antenna extension is a base with a 15-foot cable included for use with a dipole omnidirectional antenna.
For more information, see Cisco Single-Port Antenna Stand for Multiband TNC Male-Terminated Portable Antenna (Cisco 3G-AE015-R).
3G-AE010-R
(Antenna Extension)Extension Base
0.8-6.0 GHz
This is the default antenna extension. This antenna extension is a base with a 10-foot cable included for use with dipole omnidirectional antennas.
For more information, see Cisco Single-Port Antenna Stand for Multiband TNC Male-Terminated Portable Antenna (Cisco 3G-AE015-R). This document applies to both 3G-AE015-R and 3G-AE010-R. The only difference between these two products is the length of the cable.
3G-ANTM-OUT-OM
Outdoor Omnidirectional
+2 dBi
800/900 MHz+4 dBi
1800/1900/2100 MHzThis is an outdoor low-profile omnidirectional mast antenna.
For more information, see Cisco 3G Omnidirectional Outdoor Antenna (3G-ANTM-OUT-OM).
3G-ANTM-OUT-LP
Low-Profile Stick Antenna
- 1.5 dBi
850, 900 MHz- 2.5 dBi
1800, 1900, 2100 MHzThis is an omnidirectional stick antenna.
For more information, see Cisco Multiband Omnidirectional Panel-Mount Antenna (3G-ANTM-OUT-LP)
3G-ACC-OUT-LA (Lightning Arrestor)
Lightning Arrestor
800-2200 MHz
This is a quarter-wave lightning protector with integrated high-pass filter.
For more information, see Cisco 3G Lightning Arrestor (3G-ACC-OUT-LA)
3G-ACC-OUT-COMBO
Lightning Arrestor and Antenna
N/A
Multi-band outdoor omnidirectional antenna mast/wall mount (3G-ACC-OUT-OM) and 3G outdoor antenna lightning arrestor (3G-ACC-OUT-LA)
4G-ANTM-OM-CM
Low-Profile
Surface Mount Omnidirectonal698-2690 MHz
This is a ceiling mount omnidirectional antenna that can be used in any of the 3G or 4G bands (any of the 700/800/900/1700/1800/1900/2100/2600 MHz bands).
For more information, see Cisco 4G Indoor Ceiling-Mount Omnidirectional Antenna (4G-ANTM-OM-CM).
Table 6 lists insertion loss information for the ultra-low-loss (ULL) LMR 400 extension cables available from Cisco for use with 3G antennas.
Note
Figure 6 and Figure 7 show some antenna options that can be used with C880G ISRs and routers with 3G EHWIC cards, respectively.
Figure 6 Antenna Options
Figure 7 Antenna Options
Configuring EHWIC-3G-EVDO-x Cards and C880G-x-K9 ISRs
•
•
Overview of SNMP MIBs
Simple Network Management Protocol (SNMP) development and use is centered around the MIB. An SNMP MIB is an abstract database that is a conceptual specification for information that a management application may read and modify in a certain form. This does not imply that the information is kept in the managed system in that same form. The SNMP agent translates between the internal data structures and formats of the managed system and the external data structures and formats defined for the MIB.
The SNMP MIB is conceptually a tree structure with conceptual tables. Cisco 3G MIB is discussed in more detail in the next section. Relative to this tree structure, the term MIB is used in two senses. In one sense, it is actually a MIB branch, usually containing information for a single aspect of technology, such as a transmission medium or a routing protocol. A MIB used in this sense is more accurately called a MIB module and is usually defined in a single document. In the other sense, a MIB is a collection of such branches. Such a collection might comprise, for example, all the MIB modules implemented by a given agent or the entire collection of MIB modules defined for SNMP.
A MIB is a tree where the leaves are individual items of data called objects. An object may be, for example, a counter or a protocol status. MIB objects are also sometimes called variables.
MIBs can be classified into three categories:
•
•
•
3G Cellular WAN MIB Architecture
This section describes the MIB definition and implementation support for Cisco's cellular 3G WAN products on the customer premises equipment (CPE) end.
The 3G Cellular WAN MIB supports both CDMA and GSM set of cellular standards and includes the following technologies:
•
•
The 3G cellular MIB uses indexes from the cellular interface and from the modem. You can obtain the interface index using IF-MIBs and the modem index using the ENTITY MIBs.
The 3G MIB definition includes the following major sub-trees:
•
•
•
•
You can use MIB object c3gStandard defined in the c3gWanCommonTable to distinguish between CDMA or GSM and implementing MIB for CDMA or GSM.
Note
At a high-level architecture, the Cisco 3G WAN MIBs are divided into two groups and have the following structure:
1.
2.
ciscoWan3gMIBObjects
The ciscoWan3gMIBObjects group has three sub-groups:
–
–
–
–
–
c3gWanCdmaUnder c3gWanCdma, there are seven sub-groups:
•
•
•
•
•
•
•
c3gWanGsmUnder c3gWANGsm, there are five sub-groups:
•
•
•
•
•
c3gWanLbsThe following is a list of the MIB objects under c3gWanLbs:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
c3gWanSmsThe following is a list of the MIB objects under c3gWanSms:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ciscoWan3gMIBNotifs
Cisco 3G WAN MIBs implementation supports SNMP GET (read operation) for all MIB objects and SNMP SET (write operation) for the following RW (read-write) objects and more:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Note
Note
Table 7 shows various 3G WAN MIB traps and what they mean.
Restrictions
•
•
Configuration Prerequisites and Restrictions
•
Configuration Prerequisites
The following are prerequisites for configuring EHWIC cards and C880G ISRs:
•
http://www.cisco.com/go/3g.
•
•
•
•
•
–
–
–
Restrictions for Configuring 3G
The following restrictions apply to configuring EHWIC cards and C880G ISRs:
•
•
•
•
Configuring the 3G Wireless Modular and Fixed Cisco ISRs
To configure the 3G wireless modular and fixed Cisco ISRs, follow these procedures:
•
Note
Modem Activation and Provisioning
To activate and provision your modem, follow these procedures:
•
Verifying Signal Strength and Service Availability
SUMMARY STEPS
To verify the signal strength and service availability on your modem, use the following commands in EXEC mode.
Note
1.
2.
3.
4.
DETAILED STEPS
Activating the Modem
The activation procedures may differ depending on your carrier. Consult your carrier and follow one of the following procedures:
Note
Table 8 lists the activation and provisioning procedures supported by different wireless carriers, depending on the type of MC5728V modem.
Table 8 Support for Activation Procedures by SKUs and Modem Type
Yes
Yes
Yes
OTASP4 Activation
No
Yes
Yes
OMA-DM5 Activation
Yes
No
Yes
IOTA6 for Data Profile Refresh
No
No
Yes
1 MDN = mobile directory number
2 MSID = mobile subscriber identification number
3 MSL = mobile subscriber lock
4 OTASP= over-the-air service provisioning
5 OMA-DN = Open Mobile Alliance Device Management
6 IOTA = Internet-based over-the-air provisioning
Manual Activation
Note
To manually configure a modem profile, use the following command in EXEC mode:
cellular unit cdma activate manual mdn msid msl
For more information about the parameters, see the "cellular cdma activate manual" section.
In addition to activation, modem data profile provisioning is done using a process called IOTA. IOTA is initiated automatically when you use the cellular cdma activate manual command.
The following is a sample output from the cellular cdma activate manual command:
router# cellular 0/0/0 cdma activate manual 1234567890 1234567890 123456NAM 0 will be configured and will become ActiveModem will be activated with following ParametersMDN :1234567890; MSID :1234567890; SID :4183; NID 87:Checking Current Activation StatusModem activation status: Not ActivatedBegin ActivationAccount activation - Step 1 of 5Account activation - Step 2 of 5Account activation - Step 3 of 5*Jan 1 23:57:41.639: %HWIC_CELL-1-MGMT_ERROR: [Cellular0/0/0] Error response (0x1038) received from modem (err3:invalid operation type).Unable to configure MDNModem Could not be activatedc3845-1#*Jan 1 23:57:46.703: %HWIC_CELL-1-MODEM_ACK_FAIL: [Cellular0/0/0] Modem Ack not received.
Note
Tip
Activating Using OMA-DM
When you power up the modem for the first time, the modem automatically initiates Hands Free Activation (HFA) to receive over-the-air programming for the MDN and MSID numbers and refreshes mobile IP profile1 (MIP1). You will see the message "OMA DM Hands Free Activation session is active" on your device.
At the end of the session, you may see one of the following three messages depending on the activation status:
•
•
•
To check if the account is provisioned and the modem is activated, use the show cellular profile command. If the account is not activated, use the user-initiated mode using the Cisco IOS CLI to activate your modem.
To activate using the Cisco IOS CLI, use the following command in EXEC mode:
cellular slot/wic/port cdma activate oma-dm device-config
Router#cellular 0/0/0 cdma activate oma-dm device-configModem is activatedMIP profile 1 will be updated and will be active, if command is successfulBeginning OMA-DM.Router#*Feb 5 20:50:18.207: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM Device Configuration session is activeEnzo-sustaining_1841_Live#*Feb 5 20:50:34.755: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM Device Configuration completed successfullyActivating Using OTASP
To provision and activate your modem using OTASP, use the following command in EXEC mode:
cellular slot/wic_slot/port cdma activate otasp phone_number
Note
router# cellular 0/1/0 cdma activate otasp *22899Beginning OTASP activationOTASP number is *22899router#*Feb 6 23:18:45.393: OTA State = SPL unlock, Result = Success*Feb 6 23:19:10.229: OTA State = PRL downloaded, Result = Success*Feb 6 23:19:11.169: OTA State = Profile downloaded, Result = Success*Feb 6 23:19:11.173: OTA State = MDN downloaded, Result = Success*Feb 6 23:19:12.537: OTA State = Parameters committed to NVRAM, Result = Success*Feb 6 23:19:14.613: Over the air provisioning complete; Result:SuccessData Call Set up
To set up a data call, use the following procedures:
•
•
•
Figure 8 shows a data call setup using the 3G wireless EHWIC.
Figure 8 Data Call Setup with the EHWIC-3G-EVDO
Configuring the Cellular Interface
To configure the cellular interface, perform the following steps.
SUMMARY STEPS
1.
2.
3.
4.
5.
6.
Note
DETAILED STEPS
Note
Configuring DDR
To configure DDR for the cellular interface, perform the following steps.
SUMMARY STEPS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
DETAILED STEPS
Configuring DDR Backup
To monitor the primary connection and initiate the backup connection when needed, the router can use one of the following methods:
•
•
•
Configuring Interfaces to Use a Backup Interface
To configure one or more interfaces to use a backup interface, perform the following steps.
SUMMARY STEPS
1.
2.
3.
DETAILED STEPS
Note
Configuring DDR Backup Using Floating Static Route
To configure a floating static default route on the secondary interface, perform the following steps.
Note
SUMMARY STEPS
1.
2.
DETAILED STEPS
Configuring DDR Backup Using Dialer Watch
To initiate dialer watch, you must configure the interface to perform DDR and backup. Use traditional DDR configuration commands, such as dialer maps, for DDR capabilities. To enable dialer watch on the backup interface and create a dialer list, perform the following steps.
SUMMARY STEPS
1.
2.
3.
4.
5.
6.
7.
8.
DETAILED STEPS
Configuring Multiple Mobile IP Profiles
This procedure is for the EHWIC-3G-EVDO SKUs only.
Note
SUMMARY STEPS
1.
2.
DETAILED STEPS
Step 1
cellular unit cdma profile configure <profile number> <primary home agent address> <secondary home agent address> <mobile home agent address> <NAI> <MN-AAA SS> <MN-HA SS> <MN-AAA SPI> <MN-HA SPI> <rev-tunneling>
Example:Router# cellular 0/0/0 cdma profile configure 1 1.1.1.1 2.2.2.2 3.3.3.3 test@xyz.com aaa bbb 1234 1234 1
Configures data (MIP) profile.
Note
Step 2
cellular unit cdma profile select profile number
Example:Router# cellular 0/0/0 cdma profile select 1
Sets a profile as the current active profile.
Configuring Data Dedicated Transmission Mode (DDTM)
On CDMA modems, data transmission is disrupted by incoming voice calls if data dedicated transmission mode (DDTM) is disabled. You can enable DDTM mode so the modem will ignore incoming voice calls.
To enable DDTM on a CDMA modem, use the cdma ddtm command in controller configuration mode:
Router(config)# controller cellular 0Router(config-controller)# cdma ddtmThis command is enabled by default. You can disable this feature using the no form of the cdma ddtm command:
Router(config)# controller cellular 0Router(config-controller)# no cdma ddtm
Note
Configuration Examples for the 3G Wireless Modular and Fixed Cisco ISRs
This section provides the following configuration examples:
•
•
•
•
Example: Basic Cellular Interface Configuration
The following is a sample configuration where the cellular interface is used as a primary and is configured as the default route:
chat-script cdma "" "ATDT#777" TIMEOUT 60 "CONNECT"!interface Cellular0/0/0ip address negotiatedencapsulation pppdialer in-banddialer string cdmadialer-group 1async mode interactiveppp chap password 0 ciscoppp ipcp dns request!!!access-list 1 permit anydialer-list 1 protocol ip list 1!line 0/0/0exec-timeout 0 0script dialer cdmaloginmodem InOutExample: Tunnel over Cellular Interface Configuration
The following is a sample configuration, showing the static IP address when a tunnel interface is configured using the ip address unnumbered cellular interface command:
interface Tunnel2ip unnumbered GigabitEthernet0/1tunnel source Cellular0/3/0tunnel destination 128.107.248.254interface Cellular0/3/0!ip address negotiatedencapsulation pppdialer in-banddialer idle-timeout 0dialer string cdmadialer-group 1async mode interactiveppp chap password 0 ciscoppp ipcp dns request! traffic of interest through the tunnel/cellular interfaceip route 10.10.0.0 255.255.0.0 Tunnel2Example: 3G Wireless Modem as Backup with NAT and IPSec
The following is a sample configuration of a 3G wireless modem as backup with NAT and IPSec:
ip dhcp excluded-address 10.4.0.254!ip dhcp pool cdma-poolnetwork 10.4.0.0 255.255.0.0default-router 10.4.0.254!chat-script cdma "" "atdt#777" TIMEOUT 20 "CONNECT"!track 234 rtr 1 reachability!crypto isakmp policy 1encr 3desauthentication pre-share!crypto isakmp key mykey address 20.20.241.234!crypto ipsec transform-set mytransformset ah-sha-hmac esp-3des!crypto map vpn1 10 ipsec-isakmpset peer 20.20.241.234set transform-set mytransformsetmatch address 103!interface GigabitEthernet0/0ip address 10.4.0.254 255.255.0.0duplex autospeed auto!interface ATM0/0/0no ip addressip virtual-reassemblyload-interval 30no atm ilmi-keepalivedsl operating-mode auto!interface ATM0/0/0.1 point-to-pointip nat outsideip virtual-reassemblyno snmp trap link-statuspvc 0/35pppoe-client dial-pool-number 2!interface Cellular0/3/0ip address negotiatedip nat outsideencapsulation pppdialer in-banddialer idle-timeout 0dialer string cdmadialer-group 1ppp chap hostname host@apnppp chap password 0 cisco123ppp ipcp dns requestcrypto map vpn1!interface Dialer2ip address negotiatedip nat outsideencapsulation pppdialer pool 2dialer-group 2ppp chap hostname cisco@dsl.netppp chap password 0 cisco123ppp pap sent-username Cisco@dsl.net password 0 cisco123ppp ipcp dns requestcrypto map vpn1!ip local policy route-map track-primary-if!ip route 0.0.0.0 0.0.0.0 Dialer2 track 234!ip route 0.0.0.0 0.0.0.0 Cellular0/3/0 254!ip nat inside source route-map nat2cell interface Cellular0/3/0 overloadip nat inside source route-map nat2dsl interface Dialer2 overload!ip sla 1icmp-echo 209.131.36.158 source-interface Dialer2timeout 1000frequency 2ip sla schedule 1 life forever start-time now!access-list 1 permit anyaccess-list 101 deny ip 10.4.0.0 0.0.255.255 20.20.0.0 0.0.255.255access-list 101 permit ip 10.4.0.0 0.0.255.255 any!access-list 102 permit icmp any host 209.131.36.158!access-list 103 permit ip 10.4.0.0 0.0.255.255 20.20.0.0 0.0.255.255!dialer-list 1 protocol ip list 1dialer-list 2 protocol ip permit!route-map track-primary-if permit 10match ip address 102set interface Dialer2 null0!route-map nat2dsl permit 10match ip address 101match interface Dialer2!route-map nat2cell permit 10match ip address 101match interface Cellular0/3/0!event manager applet pri_backevent track 234 state anyaction 2.0 cli command "clear ip nat trans forced"!line 0/3/0script dialer cdmamodem InOutExample: Voice-Initiated Data Callback
The following example shows how to configure voice-initiated data callback on a router:
hostname 1900!boot-start-markerboot-end-marker!security passwords min-length 1enable password lab!no aaa new-modelservice-module wlan-ap 0 bootimage autonomous!no ipv6 cefip source-routeip cef!!multilink bundle-name authenticated!chat-script cdma "" "atdt#777" TIMEOUT 60 "CONNECT"!!license udi pid CISCO1941-W sn FHH1249P021!!archivelog confighidekeys!!controller Cellular 0/0!!!interface Loopback1ip address 1.1.1.1 255.255.255.255!interface Wlan-GigabitEthernet0/0description Internal switch interface connecting to the embedded AP!interface GigabitEthernet0/0no ip addressshutdownduplex autospeed auto!interface wlan-ap0description Service module interface to manage the embedded APno ip addressshutdownarp timeout 0no mop enabledno mop sysid!interface GigabitEthernet0/1no ip addressshutdownduplex autospeed auto!interface Cellular0/0/0ip address negotiatedencapsulation pppno ip mroute-cacheload-interval 30dialer in-banddialer pool-member 1dialer-group 1no peer default ip addressfair-queue 64 16 0no ppp lcp fast-startrouting dynamic!interface Vlan1no ip address!interface Dialer1ip address negotiatedencapsulation pppdialer pool 1dialer idle-timeout 0dialer string cdmadialer caller 9994082188382 callbackdialer-group 1!ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer1!no ip http serverno ip http secure-server!!dialer-list 1 protocol ip permit!!snmp-server group steeler3g v3 auth match exact notify 3gViewsnmp-server community public RWsnmp-server community steeler3g-test RWsnmp-server enable traps c3gsnmp-server host 172.27.168.158 public c3gsnmp-server host 172.27.168.158 public udp-port 6059!control-plane!!line con 0exec-timeout 0 0line aux 0line 0/0/0script dialer cdmaloginmodem InOutno exectransport input alltransport output allrxspeed 3100000txspeed 1800000line 67no activation-characterno exectransport preferred nonetransport input alltransport output pad telnet rlogin lapb-ta mop udptn v120 sshline vty 0 3password lablogin!exception data-corruption buffer truncatescheduler allocate 20000 1000end1900#Upgrading Modem Firmware
The fixed and modular ISRs have a 3G modem from Sierra Wireless. The firmware for the modem is upgradable using Cisco IOS commands. The firmware is packaged in a tar distribution file and can be downloaded from the wireless software download page on Cisco.com. Use the following procedure to upgrade the modem firmware:
Caution
Refer to the following website for the latest certified firmware version for your carrier and IOS compatibility:
To remotely download the firmware over the air, perform the following steps.
SUMMARY STEPS
Step 1
http://software.cisco.com/download/navigator.html?mdfid=279119319&flowid=6999
and in the third column, select Verizon or Sprint, depending on the type of card you have.
Note
Step 2
Step 3
Step 4
archive tar /xtract source-url destination-url
Step 5
microcode reload cellular pa-bay slot cdma modem-provision
Note
DETAILED STEPS
Step 1
Go to the Download Software site at:
http://software.cisco.com/download/navigator.html
and select Wireless > Wireless Integrated Switches and Routers. In the third column, select Verizon or Sprint, depending on the type of card you have.
Gives you access to Cisco Wireless WAN software downloads. Select firmware for Cisco 3G.
Note
Step 2
Download the appropriate CDMA firmware release under Wireless Integrated Switches and Routers.
Downloads the modem firmware package to a TFTP/FTP server that is accessible from the router with 3G.
Step 3
Copy the files to the device's flash.
—
Step 4
archive tar/xtract source-url destination-url
Example:Router# archive tar/xtract tftp://192.168.1.1/MC8775_1_0_0_7_package.tar flash:
Uncompresses the files of the modem firmware package and copies them to a location that is accessible by the router with 3G.
•
•
Step 5
microcode reload cellular pa-bay slot cdma modem-provision
Example:Router# microcode reload cellular 0 1 cdma modem-provision
Initiates the firmware upgrade process.
•
•
Note
Caution
Command Reference
This section documents new and modified commands.
•
•
•
•
•
•
•
•
cdma ddtm
On CDMA modems, data transmission is disrupted by incoming voice calls if data dedicated transmission mode (DDTM) is disabled. You can enable DDTM mode so the modem will ignore incoming voice calls.
To enable DDTM on a CDMA modem, use the cdma ddtm command in controller configuration mode. To disable DDTM, use the no form of this command.
cdma ddtm
no cdma ddtm
Syntax Description
This command has no arguments or keywords.
Command Default
DDTM is enabled by default.
Command Modes
Controller configuration (config-controller)
Command History
Usage Guidelines
Disable this feature only if you require the voice-initiated data callback feature.
Examples
The following example shows how to configure the cdma ddtm command:
router(config)# controller cellular 0/0router(config-controller)# cdma ddtmThe following example shows how to configure the no cdma ddtm command:
router(config)# controller cellular 0/0router(config-controller)# no cdma ddtmrouter(config-controller)# endThe following output for the show cellular connection command shows that DDTM is enabled:
router# show cellular 0/0/0 connectionPhone number of outgoing call =HDR AT State = Inactive, HDR Session State = CloseHDR Session Info:UATI (Hex) = 0000:0000:0000:0000:0000:0000:0000:0000Color Code = 0, RATI = 0x0Session duration = 0 msecs, Session start = 0 msecsSession end = 0 msecs, Authentication Status = Not authenticatedHDR DRC Value = 0, DRC Cover = 0, RRI = Pilot onlyCurrent Transmitted = 0 bytes, Received = 0 bytesTotal Transmitted = 0 KB, Received = 0 KBCurrent Call Status = NoneCurrent Call Duration = 0 secsTotal Call Duration = 376179855 secondsCurrent Call Type =Last Call Disconnect Reason = Modem offlineLast Connection Error = NoneHDR DDTM (Data Dedicated Transmission Mode) Preference = OnMobile IP Error Code (RFC-2002) = 0 (Registration accepted)
cdma event connection-status mib-trap
To check the connection status of a 3G WAN MIB trap event, use the cdma event connection-status mib-trap command in controller configuration mode.
cdma event connection-status mib-trap {All-cdma | active | connected | connecting | disconnected | dormant | error | inactive | idle | unknown}
Syntax Description
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example shows you how to use this command:
router(config-controller)# cdma event connection-status mib-trap activeRelated Commands
cdma event ecio abate
To set the threshold for a 3G WAN MIB trap ECIO event, use the cdma event ecio abate command in controller configuration mode.
cdma event ecio abate {mib-trap mibtrap | threshold threshold-value}
Syntax Description
Command Default
None
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events for all supported CDMA technologies when ECIO is greater than -50 dBm:
router(config-controller)# cdma event ecio abate mib-trap All-cdmarouter(config-controller)# cdma event ecio abate threshold -50The following example configures the router to send MIB trap events on the 1xrtt network when ECIO is greater than -100 dBm:
router(config-controller)# cdma event ecio abate mib-trap 1xrttrouter(config-controller)# cdma event ecio abate threshold -100Related Commands
cdma event ecio onset
Sets the ECIO onset threshold value for sending 3G WAN MIB trap events.
cdma event ecio onset
To set the ECIO onset threshold value for sending 3G WAN MIB trap events, use the cdma event ecio onset command in controller configuration mode.
cdma event ecio onset {mib-trap mibtrap | threshold threshold-value}
Syntax Description
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events on all supported CDMA networks when the ECIO value is below -50 dBm:
router(config-controller)# cdma event ecio onset mib-trap All-cdmarouter(config-controller)# cdma event ecio onset threshold -50The following example configures the router to send MIB trap events on the evdoRel0 network when the ECIO value is below -100 dBm:
router(config-controller)# cdma event ecio onset mib-trap evdoRel0router(config-controller)# cdma event ecio onset threshold -100Related Commands
cdma event ecio abate
Sets the ECIO abate threshold value for sending 3G WAN MIB trap events.
cdma event modem-state mib-trap
To set the modem state for sending 3G WAN MIB trap events, use the cdma event modem-state mib-trap command in controller configuration mode.
cdma event modem-state mib-trap {all | up | down}
Syntax Description
all
Sends MIB trap events when the modem is up or down.
up
Sends MIB trap events when the modem is up.
down
Sends MIB trap events when the modem is down.
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events only when the modem is down:
router(config-controller)# cdma event modem-state mib-trap downRelated Commands
cdma event network mib-trap
To configure the router to send 3G WAN MIB trap events when network changes occur, use the cdma event network mib-trap command in controller configuration mode.
cdma event network mib-trap
Syntax Description
This command has no arguments or keywords.
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events in response to network changes (for example, switching from an AT&T network to a Verizon network):
router(config-controller)# cdma event network mib-trapRelated Commands
cdma event rssi abate
To set the RSSI abate threshold value for sending 3G WAN MIB trap events, use the cdma event rssi abate command in controller configuration mode.
cdma event rssi abate {mib-trap mibtrap | threshold threshold-value}
Syntax Description
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events for all supported CDMA technologies when RSSI is greater than -50 dBm:
router(config-controller)# cdma event rssi abate mib-trap All-cdmarouter(config-controller)# cdma event rssi abate threshold -50The following example configures the router to send MIB trap events on the evdoRel0 network when RSSI is greater than -100 dBm:
router(config-controller)# cdma event rssi abate mib-trap evdoRel0router(config-controller)# cdma event rssi abate threshold -100Related Commands
cdma event rssi onset
Sets the RSSI onset threshold value for sending 3G WAN MIB trap events.
cdma event rssi onset
To set the RSSI onset threshold value for sending 3G WAN MIB trap events, use the cdma event rssi onset command in controller configuration mode.
cdma event rssi onset {mib-trap mibtrap | threshold threshold-value}
Syntax Description
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events on all supported CDMA networks when RSSI is below -50 dBm:
router(config-controller)# cdma event rssi onset mib-trap All-cdmarouter(config-controller)# cdma event rssi onset threshold -50The following example configures the router to send MIB trap events on the evdoRel0 network when RSSI is below -100 dBm:
router(config-controller)# cdma event rssi onset mib-trap evdoRel0router(config-controller)# cdma event rssi onset threshold -100Related Commands
cdma event rssi abate
Sets the RSSI abate threshold value for sending 3G WAN MIB trap events.
cdma event service mib-trap
To configure the router to send 3G WAN MIB trap events when service changes occur, use the cdma event service mib-trap command in contoller configuration mode.
cdma event service mib-trap
Syntax Description
This command has no arguments or keywords.
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example configures the router to send MIB trap events in response to service changes (for example, switching from evdoRel0 to evdoRelA):
router(config-controller)# cdma event service mib-trapRelated Commands
cdma event temperature abate
To set the temperature abate threshold value for sending 3G WAN MIB trap events, use the cdma event temperature abate command in controller configuration mode.
cdma event temperature abate {mib-trap | threshold threshold-value}
Syntax Description
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example enables temperature abate MIB trap events, then configures the router to send MIB trap events when temperature goes below 32°F (0°C):
router(config-controller)# cdma event temperature abate mib-traprouter(config-controller)# cdma event temperature abate threshold 0Related Commands
cdma event temperature onset
To set the temperature onset threshold value for sending 3G WAN MIB trap events, use the cdma event temperature onset command in controller configuration mode.
cdma event temperature onset {mib-trap | threshold threshold-value}
Syntax Description
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example enables temperature onset MIB trap events, then configures the router to send MIB trap events when temperature goes above 32°F (0°C):
router(config-controller)# cdma event temperature onset mib-traprouter(config-controller)# cdma event temperature onset threshold 0Related Commands
cdma gps mode
To enable the GPS mode, use the cdma gps mode command in privileged EXEC mode.
cdma gps mode standalone
Syntax Description
standalone
Ena bles autonomous GPS without assistance data. The Mobile Station computes its own location; no position determination equipment is required. This is the Default mode.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example enables the standalone GPS mode:
router# cdma gps mode standaloneRelated Commands
debug cellular messages gps
Displays the GPS background activities for debugging purposes.
show cellular gps
Displays GPS statistics.
cdma gps nmea
To enable or disable GPS National Marine Electronics Association (NMEA) stream state, use the
cdma gps nmea command in privileged EXEC mode.cdma gps nmea
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example enables the NMEA stream state:
router# cdma gps nmeaRelated Commands
debug cellular messages nmea
Displays NMEA background activities for debugging purposes.
cdma sms archive path
To configure the FTP settings of the directory used to archive SMS messages, use the cdma sms archive path command in controller configuration mode.
cdma sms archive path ftp:FTP-path
Syntax Description
Command Default
None
Command Modes
Controller configuration (config-controller)
Command History
Examples
The following example sets the FTP path to the SMS_archive directory on the FTP server at 192.168.1.3:
router(config-controller)# cdma sms archive path ftp://username:password@192.168.1.3/SMS_archiveRelated Commands
cellular cdma activate iota
To periodically refresh the modem data profile using Internet-based over-the-air provisioning (IOTA), use the cellular cdma activate iota command in privileged EXEC mode.
cellular slot/wic_slot/port cdma activate iota
Syntax Description
slot/wic_slot/port
Numeric values that indicate the router slot, WAN interface card (WIC) slot, and port.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
IOTA is used by some wireless service providers to activate the modem data profile . Use the cellular cdma activate iota command to display the current active connection state and statistics. (Ask your carrier whether IOTA is supported and how often a refresh is needed.)
You can verify the updated modem data profile using the show cellular slot/wic_slot/port profile command.
Note
Examples
The following is a sample output from the cellular cdma activate iota command:
router# cellular 0/0/0 cdma activate iotaBegin IOTArouter#*Feb 6 23:32:21.339: IOTA Status Message Received. Event: IOTA Start, Result: SUCCESS*Feb 6 23:32:21.339: Please wait till IOTA END message is received*Feb 6 23:32:21.339: It can take up to 5 minutes*Feb 6 23:32:40.867: OTA State = SPL unlock, Result = Success*Feb 6 23:32:45.235: OTA State = Parameters commited to NVRAM, Result = Success*Feb 6 23:32:52.087: Over the air provisioning complete; Result:Success*Feb 6 23:32:52.615: IOTA Status Message Received. Event: IOTA End, Result: SUCCESSRelated Commands
cellular cdma activate manual
Manually activates a cellular account using the over-the-air service procedure.
show cellular profile
Displays the cellular profile information.
cellular cdma activate manual
To manually activate the modem, use the cellular cdma activate manual command in privileged EXEC mode.
Note
cellular unit cdma activate manual {mdn | msid | msl}
Syntax Description
unit
Numeric values that indicate the router slot, WAN interface card (WIC) slot, and port.
mdn
Ten-digit MDN.
msid
Ten-digit MSID.
msl
MDL obtained from your service provider.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
Use the show cellular network command to obtain the system identification number and the network identification number.
You can verify whether the modem has been activated using the show cellular slot/wic_slot/port all command.
Note
Examples
The following is a sample output from the cellular cdma activate manual command:
router# cellular 0/0/0 cdma activate manual 1234567890 1234567890 123456NAM 0 will be configured and will become ActiveModem will be activated with following ParametersMDN :1234567890; MSID :1234567890; SID :4183; NID 87:Checking Current Activation StatusModem activation status: Not ActivatedBegin ActivationAccount activation - Step 1 of 5Account activation - Step 2 of 5Account activation - Step 3 of 5*Jan 1 23:57:41.639: %HWIC_CELL-1-MGMT_ERROR: [Cellular0/0/0] Error response (0x1038) received from modem (err3:invalid operation type).Unable to configure MDNModem Could not be activatedc3845-1#*Jan 1 23:57:46.703: %HWIC_CELL-1-MODEM_ACK_FAIL: [Cellular0/0/0] Modem Ack not received.The following is a sample output from the show cellular profile command after the modem has been activated:
router# show cellular 0/3/0 profileProfile Information====================Electronic Serial Number (ESN) = 0x603C6426Modem activated = YESAccount Information:======================Activation Date: 20070221Phone Number (MDN) : 2029976763Mobile Station Identifier (MSID) : 2029976763Data Profile Info:=====================Number of data profiles configured : 1Current active data profile : 0Data Profile 0 Information (Active)==================================NAI (Network Access Identifier) = 2029976763@vzw3g.comMN-HA SS = SetMN-HA SPI = 300MN-AAA SS = SetMN-AAA SPI = 2Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 255.255.255.255Secondary Home Agent Address = 255.255.255.255Related Commands
cellular cdma activate oma-dm device config
To start a user-initiated Open Mobile Alliance Device Management (OMA-DM) session to provision an account and MIP1 (Mobile IP) profile update, use the cellular cdma activate oma-dm device config command in privileged EXEC mode.
cellular slot/wic_slot/port cdma activate oma-dm device config
Syntax Description
slot/wic_slot/port
Numeric values that indicate the router slot, WAN interface card (WIC) slot, and port.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
The cellular cdma activate oma-dm device config command refreshes the mobile directory number (MDN) and mobile subscriber identification number (MSID) on the account.
Before you execute this command, terminate any existing active or dormant data connection. The modem is activated automatically when it powers up using Hands Free Activation. Use this command only when activation fails or you need to update your account parameters.
To view profile and MIB information, use the show cellular profile command.
Examples
The following example shows the output for slot 0, WIC slot 0, and port 0 of HWIC-3G-CDMA:
router# cellular 0/0/0 cdma activate oma-dm device-configModem is activatedMIP profile 1 will be updated and will be active, if command is successfulBeginning OMA-DM.router#*Feb 5 20:50:18.207: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM Device Configuration session is activeRouter_1841_Live#*Feb 5 20:50:34.755: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM Device Configuration completed successfullyRelated Commands
cellular cdma activate oma-dm ni-alert
To allow or deny a network-initiated alert (NIA) queued in the modem, use the cellular cdma activate oma-dm ni-alert command in privileged EXEC mode.
cellular slot/wic_slot/port cdma activate oma-dm ni-alert {allow | deny}
Syntax Description
slot/wic_slot/port
Numeric values that indicate the router slot, WAN interface card (WIC) slot, and port.
allow
Allows a network-initiated alert.
deny
Denies a network-initiated alert.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
On execution of the cellular cdma activate oma-dm ni-alert command, a message warns that the current data connection will be interrupted. You must confirm if you want to proceed with this command.
Note
Examples
The following is a sample output for slot 0, WIC slot 0, and port 0 of HWIC-3G-CDMA with network-initiated alert while the modem is in dormant state:
*Feb 5 20:57:04.827: %CELLWAN-2-OMA_DM_NI_ALERT: [Cellular0/0/0]: OMA DM NI Alert is received for Device ConfigurationPlease execute 'cellular <unit> cdma activate oma-dm ni-alert [allow | deny]'router# cellular 0/0/0 cdma activate oma-dm ni-alert allowModem is activated!!!WARNING: Data connection will be terminated. Service will be interrupted until the NI session is completed.Are you sure?(y/n) [confirm][Cellular0/0/0]:The interface will be shutdown to allow the Network-Initiated OMA DM session. This will terminate any active data connection.OMA DM NI alert: Interactive response accepted*Feb 5 20:57:19.611: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0/0/0, changed state to down*Feb 5 20:57:20.627: %LINK-5-CHANGED: Interface Cellular0/0/0, changed state to administratively down*Feb 5 20:57:26.063: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM Device Configuration session is active*Feb 5 20:57:36.847: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM Device Configuration completed successfullyThe following is a sample output from the cellular slot/wic_slot/port cdma activate oma-dm ni-alert deny command for slot 0, WIC slot 0, and port 0 of HWIC-3G-CDMA:
*Feb 5 21:01:08.487: %CELLWAN-2-OMA_DM_NI_ALERT: [Cellular0/0/0]: OMA DM NI Alert is received for Device ConfigurationPlease execute 'cellular <unit> cdma activate oma-dm ni-alert [allow | deny]'Enzo-sustaining_1841_Live# cellular 0/0/0 cdma activate oma-dm ni-alert denyModem is activatedOMA DM NI alert: Interactive response acceptedTable 9 describes the output fields from the command.
Related Commands
cellular cdma activate oma-dm prl-update
To start a user-initiated Open Mobile Alliance Device Management (OMA-DM) session to get an over-the-air PRL update, use the cellular cdma activate oma-dm prl-update command in privileged EXEC mode.
cellular slot/wic_slot/port cdma activate oma-dm prl-update
Syntax Description
slot/wic_slot/port
Numeric values that indicate the router slot, WAN interface card (WIC) slot, and port.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
Preferred roaming list (PRL) upates are provided periodically by the service provider. If no updates are available, an empty session error message is returned.
Note
Examples
The following is a sample ouptut for slot 0, WIC slot 0, and port 0 of HWIC-3G-CDMA when the update is successful:
router# cellular 0/0/0 cdma activate oma-dm prl-updateModem is activatedBeginning OMA-DM*Jan 27 18:32:08.087: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM PRL Update session is active*Jan 27 18:32:31.643: %CELLWAN-2-OMA_DM_SUCCESS: [Cellular0/0/0]: OMA DM PRL Update completed successfullyThe following is a sample ouptut for slot 0, WIC slot 0, and port 0 of HWIC-3G-CDMA when the update is unsuccessful:
router# cellular 0/0/0 cdma activate oma-dm prl-updateModem is activatedBeginning OMA-DM.*Feb 5 21:33:23.795: %CELLWAN-2-OMA_DM_ACTIVE: [Cellular0/0/0]: OMA DM PRL Update session is active*Feb 5 21:34:03.587: %CELLWAN-2-OMA_DM_ERROR: [Cellular0/0/0]: OMA DM PRL Update Failed - Error:0x504(Unrecoverable network error)Related Commands
cellular cdma activate otasp
To activate a wireless account using over-the-air service provisioning (OTASP), use the cellular cdma activate otasp command in privileged EXEC mode.
Note
cellular slot/wic_slot/port cdma activate otasp phone_number
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
You can verify the modem activation using the show cellular slot/wic_slot/port all command.
Note
Examples
The following is a sample output from the cellular cdma activate otasp command:
router# cellular 0/1/0 cdma activate otasp *22899Beginning OTASP activationOTASP number is *22899router#*Feb 6 23:18:45.393: OTA State = SPL unlock, Result = Success*Feb 6 23:19:10.229: OTA State = PRL downloaded, Result = Success*Feb 6 23:19:11.169: OTA State = Profile downloaded, Result = Success*Feb 6 23:19:11.173: OTA State = MDN downloaded, Result = Success*Feb 6 23:19:12.537: OTA State = Parameters commited to NVRAM, Result = Success*Feb 6 23:19:14.613: Over the air provisioning complete; Result:SuccessThe following is a sample output from the show cellular profile command after the modem has been activated:
router# show cellular 0/3/0 profileProfile Information====================Electronic Serial Number (ESN) = 0x603C6426Modem activated = YESAccount Information:======================Activation Date: 20070221Phone Number (MDN) : 2029976763Mobile Station Identifier (MSID) : 2029976763Data Profile Info:=====================Number of data profiles configured : 1Current active data profile : 0Data Profile 0 Information (Active)==================================NAI (Network Access Identifier) = 2029976763@vzw3g.comMN-HA SS = SetMN-HA SPI = 300MN-AAA SS = SetMN-AAA SPI = 2Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 255.255.255.255Secondary Home Agent Address = 255.255.255.255Related Commands
cellular cdma mode
To configure the modem mode to connect to 1xRTT, EVDO, or hybrid services, use the cellular cdma mode command in privileged EXEC mode.
cellular slot/wic_slot/port cdma mode {hybrid | EVDO-only | 1xRTT-only}
Syntax Description
Command Default
Connects to hybrid (EVDO/1xRTT) services.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
This command is executed only upon confirmation from the user. A service mode change is followed by a modem reset.
Examples
The following is a sample output for slot 0, WIC slot 1, and port 1 of HWIC-3G-CDMA:
router# cellular 0/1/1 cdma mode ?1xRTT Modem will connect to 1xRTT only serviceevdo Modem will connect to EVDO only servicehybrid Modem will connect to EVDO and 1xRTT service (default behavior)Table 10 describes the output fields from the command.
Related Commands
cellular cdma profile configure
To manipulate CDMA modem data profile information, use the cellular cdma profile configure command in privileged EXEC mode.
cellular slot/wic_slot/port cdma profile configure <profile number> <primary HA address> <secondary HA address><mobile HA><NAI> <MN-AAA SS> <MN-HA SS> <MN-AAA SPI><MN-HA SPI> <rev-tunneling>
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
This command is not supported for the HWIC-3G-CDMA-V SKU.
Examples
The following is a sample output for the cellular unit cdma profile configure command.
Sample Output for HWIC-3G-CDMA
router#cellular 0 cdma profile configure ?<1-5> profile numberrouter#cellular 0 cdma profile configure 5 ?A.B.C.D Primary HA Addressrouter#cellular 0 cdma profile configure 5 100.1.1.1 ?A.B.C.D Secondary HA Addressrouter#cellular 0 cdma profile configure 5 100.1.1.1 200.1.1.1 ?WORD Network Access Identifier (Ex:username@domain)router#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com ?WORD MN-AAA Shared Secretrouter#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com kkk ?WORD MN-HA Shared Secretrouter#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com kkk mmm ?<cr>router#$le configure 5 100.1.1.1 200.1.1.1 testing@sp.com kkk mmmProfile 5 will be configured with following parameters:NAI (Network Access Identifier) = testing@sp.comHome Address = 0.0.0.0Primary Home Agent Address = 100.1.1.1Secondary Home Agent Address = 200.1.1.1MN-AAA SS = SetMN-HA SS = SetMN-AAA SPI = 1234MN-HA SPI = 1234Reverse Tunneling Preference = Set!!!WARNING: Modem will be resetAre you sure? [confirm]Done configuring - Please wait while the modem resets*Feb 25 21:21:37.504: %CISCO800-2-MODEM_REMOVAL_DETECTED: Cellular0 modem is now REMOVED*Feb 25 21:21:37.504: %CISCO800-2-CELLULAR_INTERFACE_NOT_SHUTDOWN: WARNING: Cellular0 interface should be shutdown before removing modem. Reload Required to reset interface*Feb 25 21:21:38.508: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to down*Feb 25 21:21:43.264: %CELLWAN-2-HEART_BEAT_TIMEOUT: No heart beat signal from Cellular0*Feb 25 21:21:43.540: %CISCO800-2-MODEM_INSERTED_DETECTED: Cellular0 modem is now INSERTED*Feb 25 21:21:43.544: %CELLWAN-2-MODEM_DOWN: Cellular0 modem is DOWN*Feb 25 21:21:45.540: %LINK-5-CHANGED: Interface Cellular0, changed state to resetProfile 5 configured successfullyrouter#router#*Feb 25 21:21:48.648: %CELLWAN-2-MODEM_UP: Cellular0 modem is now UProuter#router#sh*Feb 25 21:21:50.540: %LINK-3-UPDOWN: Interface Cellular0, changed state to downrouter#show cellurouter#show cellular 0 prouter#show cellular 0 profile 5Electronic Serial Number (ESN) = 0x605F6982 [09606252930]Modem activated = YESAccount Information:======================Activation Date: Not availablePhone Number (MDN) : 4084205046Mobile Station Identifier (MSID) : 4084205046Data Profile Info:=====================Number of data profiles configurable : 5Current active data profile : 1Data Profile 5 Information==================================NAI (Network Access Identifier) = testing@sp.comMN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 100.1.1.1Secondary Home Agent Address = 200.1.1.1router#cellular cdma profile select
To select a CDMA modem data profile, use the cellular cdma profile select command in privileged EXEC mode.
cellular slot/wic_slot/port cdma profile select <profile number> <primary HA address> <secondary HA address> <mobile HA> <NAI> <MN-AAA SS> <MN-HA SS> <MN-AAA SPI> <MN-HA SPI> <rev-tunneling>
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
This command is not supported for the HWIC-3G-CDMA-V SKU.
Examples
The following is a sample output from the cellular slot/wic_slot/port cdma profile select command for HWIC-3G-CDMA:
router# cellular 0 cdma profile select 5 ?<cr>router# cellular 0 cdma profile select 5Profile 5 will become active!!!WARNING: Modem will be resetAre you sure? [confirm]Done configuring - Please wait while the modem resets*Feb 25 21:23:58.224: %CISCO800-2-MODEM_REMOVAL_DETECTED: Cellular0 modem is now REMOVED*Feb 25 21:23:58.224: %CISCO800-2-CELLULAR_INTERFACE_NOT_SHUTDOWN: WARNING: Cellular0 interface should be shutdown before removing modem. Reload Required to reset interface*Feb 25 21:23:58.232: %CELLWAN-2-MODEM_DOWN: Cellular0 modem is DOWN*Feb 25 21:23:59.784: %CISCO800-2-MODEM_INSERTED_DETECTED: Cellular0 modem is now INSERTED*Feb 25 21:24:04.900: %CELLWAN-2-MODEM_UP: Cellular0 modem is now UPProfile 5 selected successfullyrouter#router#router#router#router# show cellular 0 profile 5Electronic Serial Number (ESN) = 0x605F6982 [09606252930]Modem activated = YESAccount Information:======================Activation Date: Not availablePhone Number (MDN) : 4084205046Mobile Station Identifier (MSID) : 4084205046Data Profile Info:=====================Number of data profiles configurable : 5Current active data profile : 5Data Profile 5 Information (Active) <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<==================================NAI (Network Access Identifier) = testing@sp.comMN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 100.1.1.1Secondary Home Agent Address = 200.1.1.1router#Related Commands
cellular cdma sms delete
To delete an SMS message on the CDMA band, use the cellular cdma sms delete command in privileged EXEC mode.
cellular unit cdma sms delete {all | message-id}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example deletes all SMS messages:
router# cellular 0/1/0 cdma sms delete allRelated Commands
cellular cdma sms send
To send an outgoing SMS message on the CDMA band, use the cellular cdma sms send command in privileged EXEC mode.
cellular unit cdma sms send destination-number sms-content
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example shows how to send an SMS message:
router# cellular 0/1/0 cdma sms send <phone number> "Test message"Related Commands
cellular cdma sms view
To display all incoming messages on the CDMA band stored on the SIM card, use the cellular cdma sms view command in privileged EXEC mode.
cellular unit cdma sms view {summary | all | message-id}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Examples
The following is a sample output from the cellular cdma sms view command:
router# cellular 0/1/0 cdma sms view 3SMS ID: 3TIME: 10/05/04 21:56:58FROM: 4087993680SIZE: 32from john This is a test messageRelated Commands
debug cell-hwic driver
To debug the Cisco IOS driver for the cellular interface, use the debug cell-hwic driver command in privileged EXEC mode.
debug cell-hwic unit driver {crcdump | errdump | errors}
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
crcdump
CRC error details.
errdump
Other error details.
errors
Errors debugging.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
Use this command for debugging purposes only.
Related Commands
debug cell-hwic firmware
To see the Cisco IOS firmware information, use the debug cell-hwic firmware command in privileged EXEC mode.
debug cell-hwic unit firmware
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
Use this command for debugging purposes only.
Related Commands
debug cell-hwic virt-con
To redirect the Nios II console driver messages to display in the Cisco IOS router console environment, use the debug cell-hwic virt-con command in privileged EXEC mode.
debug cell-hwic unit virt-con [clear | disable | dump-data-structs | log | monitor | wrapper-on | wrapper-off]
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
Use this command for debugging purposes only.
Related Commands
debug cellular messages all
To print all Cisco IOS driver debug messages, use the debug cellular messages all command in privileged EXEC mode.
debug cellular unit messages all
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
Use this command for debugging purposes only.
Related Commands
debug cellular messages async
To debug cellular async, use the debug cellular messages async command in privileged EXEC mode.
debug cellular unit messages async
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
Use this command for debugging purposes only.
Related Commands
debug cellular messages data
To print Cisco IOS data path debug messages, use the debug cellular messages data command in privileged EXEC mode.
debug cellular unit messages data
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
Use this command for debugging purposes only.
Related Commands
debug cellular messages gps
To display the GPS background activities for debugging purposes, use the debug cellular messages gps command in privileged EXEC mode.
debug cellular unit messages gps
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following is a sample output for the debug cellular messages gps command:
router# debug cellular 0/1/0 messages gpsGPS debugging is onRelated Commands
debug cellular messages nmea
To display NMEA background activities for debugging purposes, use the debug cellular messages nmea command in privileged EXEC mode.
debug cellular unit messages nmea
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following is a sample output for the debug cellular messages nmea command:
router# debug cellular 0/1/0 messages nmeaRelated Commands
debug cellular messages sms
To display SMS background activities (for example, SMS downloading, deleting, and sending activities) for debugging purposes, use the debug cellular messages sms command in privileged EXEC mode.
debug cellular unit messages sms
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following is a sample output for the debug cellular messages sms command:
router# debug cellular 0/1/0 messages smsRelated Commands
show cellular all
To display all the modem information in one listing, use the show cellular all command in privileged EXEC mode.
show cellular unit all
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the output is different for each.
Examples
The following example shows the output from the show cellular all command for slot 0, WIC slot 3, and port 0:
router# show cellular 0/0/0 allHardware Information====================Modem Firmware Version = p2813301Modem Firmware built = 06-24-10Hardware Version = MC5728V Rev 1.0Electronic Serial Number (ESN) = 0x609938F3 [09610041587]Preferred Roaming List (PRL) Version = 60667PRI SKU ID = 535491Current Modem Temperature = 30 degrees CelsiusEndpoint Port Map = 75Profile Information====================Electronic Serial Number (ESN) = 0x609938F3 [09610041587]Modem activated = YESAccount Information:======================Activation Date: 20100517Phone Number (MDN) : 4088368172Mobile Station Identifier (MSID) : 4088368172Data Profile Info:=====================Number of data profiles configurable : 5Current active data profile : 1Data Profile 0 Information==================================NAI (Network Access Identifier) = 609938F3@hcm.sprintpcs.comMN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 68.28.15.12Secondary Home Agent Address = 68.28.31.12Data Profile 1 Information (Active)==================================NAI (Network Access Identifier) = cpciscosystemsin103@sprintpcs.comMN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 255.255.255.255Secondary Home Agent Address = 68.28.57.76Data Profile 2 Information==================================NAI (Network Access Identifier) =MN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 0.0.0.0Secondary Home Agent Address = 0.0.0.0Data Profile 3 Information==================================NAI (Network Access Identifier) =MN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 0.0.0.0Secondary Home Agent Address = 0.0.0.0Data Profile 4 Information==================================NAI (Network Access Identifier) =MN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 0.0.0.0Secondary Home Agent Address = 0.0.0.0Data Profile 5 Information==================================NAI (Network Access Identifier) =MN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 0.0.0.0Secondary Home Agent Address = 0.0.0.0Data Connection Information===========================Phone number of outgoing call = #777HDR AT State = Inactive, HDR Session State = CloseHDR Session Info:UATI (Hex) = 0000:0000:0000:0000:0000:0000:0000:0000Color Code = 0, RATI = 0x0Session duration = 0 msecs, Session start = 0 msecsSession end = 0 msecs, Authentication Status = Not authenticatedHDR DRC Value = 0, DRC Cover = 0, RRI = Pilot onlyCurrent Transmitted = 163 bytes, Received = 324 bytesTotal Transmitted = 369 KB, Received = 9 KBCurrent Call Status = DORMANTCurrent Call Duration = 729 secsTotal Call Duration = 1986008 secondsCurrent Call Type = AT Packet Call DormantLast Call Disconnect Reason = Client ended callLast Connection Error = NoneHDR DDTM (Data Dedicated Transmission Mode) Preference = OffMobile IP Error Code (RFC-2002) = 0 (Registration accepted)Network Information===================Current Service = 1xRTT onlyCurrent Roaming Status(1xRTT) = HOME, (HDR) = HOMECurrent Idle Digital Mode = CDMACurrent System Identifier (SID) = 4183Current Network Identifier (NID) = 87Current Call Setup Mode = Mobile IP Preferred with SIP fallbackSIP Username = 0, SIP Password =Serving Base Station Longitude = -121 deg -55 min -8 secServing Base Station Latitude = 37 deg 25 min 22 secCurrent System Time = Wed Jan 12 14:50:8 2011Radio Information=================1xRTT related info------------------Current RSSI = -82 dBm, ECIO = -4 dBmCurrent Channel Number = 75Current Channel State = AcquiredCurrent Band Class = Band Class 1HDR (1xEVDO) related info-------------------------Current RSSI = -125 dBm, ECIO = -2 dBmCurrent Channel Number = 65535Current Band Class = Band Class 0Sector ID (Hex) = 0000:0000:0000:0000:0000:0000:0000:0000Subnet Mask = 0, Color Code = 0, PN Offset = 0Rx gain control(Main) = Unavailable, Diversity = UnavailableTx total power = 0 dBm, Tx gain adjust = 0 dBmCarrier to interference (C/I) ratio = 0Modem Security Information==========================Modem PIN Security UNLOCKEDPower-up lock DISABLEDGPS Information==========================GPS Info-------------GPS State: GPS location errorGPS Mode Configured: standaloneLast Location Fix Error: Fix error [0xF]SMS Information===============Incoming Message Information----------------------------SMS stored in modem = 0SMS archived since booting up = 0Total SMS deleted since booting up = 0Storage records allocated = 99Storage records used = 0Number of callbacks triggered by SMS = 0Number of successful archive since booting up = 0Number of failed archive since booting up = 0Outgoing Message Information----------------------------Total SMS sent successfully = 0Total SMS send failure = 0Number of outgoing SMS pending = 0Number of successful archive since booting up = 0Number of failed archive since booting up = 0Last Outgoing SMS Status = SUCCESSSMS-Send-Status:SMS ID = 0Error Class = 0x0Cause Code = 0x0SMS Archive URL =OMA DM Information==================Configuration info------------------DM Support = EnabledMax DM account = 1, DM account in use = 1DM account changed = NoDevice Configuration:Client-Initiated = Supported, EnabledNetwork-Initiated = Supported, EnabledPRL Update:Client-Initiated = Supported, EnabledNetwork-Initiated = Supported, EnabledFirmware Update:Client-Initiated = Supported, EnabledNetwork-Initiated = Supported, EnabledHands Free Activation:Device-Initiated = Supported, EnabledHands Free Activation attempted = YesDM session state info---------------------DM session state = Session not activeLast session type = UnspecifiedLast session initiator = UnspecifiedLast session UI mode = UnspecifiedLast session result = SuccessLast session updated = NoNetwork-Initiated alert info----------------------------NIA state = No NIA pendingSession type = UnspecifiedStandard UI mode = UnspecifiedSpecial UI mode = Unspecifiedc1921_snmp#CDMAc1921_snmp#sh cellular 0/0/0 allHardware Information====================Modem Firmware Version = T0_2_5_2AP R263 CNSModem Firmware built = 11/12/10Hardware Version = 1.0International Mobile Subscriber Identity (IMSI) = 00112345678901International Mobile Equipment Identity (IMEI) = 353567040022155Integrated Circuit Card ID (ICCID) = 89600109080705906843Mobile Subscriber International SubscriberIDentity Number (MSISDN) =Factory Serial Number (FSN) = CC3291001281001Modem Status = OnlineCurrent Modem Temperature = 38 deg C, State = NormalPRI SKU ID = 9900198, SKU Rev. = 1.1Profile Information====================Profile 1 = INACTIVE*--------PDP Type = IPv4Access Point Name (APN) =Authentication = NoneUsername: , Password:* - Default profileData Connection Information===========================Data Transmitted = 500 bytes, Received = 500 bytesProfile 1, Packet Session Status = INACTIVEInactivity Reason = PDP establish max timeoutProfile 2, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 3, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 4, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 5, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 6, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 7, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 8, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 9, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 10, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 11, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 12, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 13, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 14, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 15, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 16, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateNetwork Information===================Current Service Status = Emergency Only, Service Error = NoneCurrent Service = InvalidPacket Service = NonePacket Session Status = InactiveCurrent Roaming Status = HomeNetwork Selection Mode = AutomaticCountry = USA, Network = AT&TMobile Country Code (MCC) = 310Mobile Network Code (MNC) = 410Location Area Code (LAC) = 6042Routing Area Code (RAC) = 1Cell ID = 31611Primary Scrambling Code = 0PLMN Selection = AutomaticRadio Information=================Radio power mode = ONCurrent Band = CDMA 1900, Channel Number = 563Current RSSI = -103 dBmBand Selected = AutoNumber of nearby cells = 1Cell 1Primary Scrambling Code = 0x106RSCP = -119 dBm, ECIO = -19 dBmModem Security Information==========================Card Holder Verification (CHV1) = DisabledSIM Status = OKSIM User Operation Required = NoneNumber of CHV1 Retries remaining = 3GPS Information==========================GPS Info-------------GPS State: GPS disabledSMS Information===============Incoming Message Information----------------------------SMS stored in modem = 2SMS archived since booting up = 0Total SMS deleted since booting up = 0Storage records allocated = 10Storage records used = 2Number of callbacks triggered by SMS = 0Number of successful archive since booting up = 0Number of failed archive since booting up = 0Outgoing Message Information----------------------------Total SMS sent successfully = 0Total SMS send failure = 0Number of outgoing SMS pending = 0Number of successful archive since booting up = 0Number of failed archive since booting up = 0Last Outgoing SMS Status = SUCCESSCopy-to-SIM Status = 0x0Send-to-Network Status = 0x0Report-Outgoing-Message-Number:Reference Number = 0Result Code = 0x0Diag Code = 0x0 0x0 0x0 0x0 0x0SMS Archive URL =Related Commands
show cellular security
Displays the modem lock state.
show controllers cellular
Displays EHWIC hardware- and driver-specific information.
show cellular connection
To display the current active connection state and data statistics, use the show cellular connection command in privileged EXEC mode.
show cellular unit connection
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the output is different for each.
Examples
The following is a sample output for slot 0, WIC slot 0, and port 0 from the show cellular connection command:
router# show cellular 0/0/0 connectionPhone number of outgoing call =HDR AT State = Idle, HDR Session State = OpenHDR Session Info:UATI (Hex) = 0084:0AC0:0000:0000:000A:05DC:A821:DCFCColor Code = 32, RATI = 0xFFFFFFFFSession duration = 0 msecs, Session start = 0 msecsSession end = 0 msecs, Authentication Status = Not authenticatedHDR DRC Value = 11, DRC Cover = 0, RRI = Pilot onlyCurrent Transmitted = 0 bytes, Received = 0 bytesTotal Transmitted = 0 KB, Received = 0 KBCurrent Call Status = DISCONNECTEDCurrent Call Duration = 30 secsTotal Call Duration = 4482879 secondsCurrent Call State =Last Call Disconnect Reason = Base station release (No reason)Last Connection Error = NoneHDR DDTM (Data Dedicated Transmission Mode) Preference = OffMobile IP Error Code (RFC-2002) = 0 (Registration accepted)router#Table 11 describes each output field.
Related Commands
show cellular gps
To display GPS statistics, use the show cellular gps command in privileged EXEC mode.
show cellular unit gps
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example displays the GPS statistics:
router# show cellular 0/0/0 gpsRelated Commands
cdma gps mode
Enables the GPS mode.
debug cellular messages gps
Displays the GPS background activities for debugging purposes.
show cellular hardware
To display the cellular modem hardware information, use the show cellular hardware command in privileged EXEC mode.
show cellular unit hardware
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the output is different for each.
Examples
The following is a sample output for slot 0, WIC slot 1, and port 0:
router# show cellular 0/0/0 hardwareModem Firmware Version = p2813301Modem Firmware built = 06-24-10Hardware Version = MC5728V Rev 1.0Electronic Serial Number (ESN) = 0x60E62C87 [09615084679]Preferred Roaming List (PRL) Version = 10PRI SKU ID = 535479Carrier ID = 19 Carrier Name = RelianceCurrent Modem Temperature = 30 degrees CelsiusEndpoint Port Map = 75router#router# show cellular 0/1/0 hardwareModem Firmware Version = p2813301Modem Firmware built = 06-24-10Hardware Version = MC5728V Rev 1.0Electronic Serial Number (ESN) = 0x60E62431 [09615082545]Preferred Roaming List (PRL) Version = 10PRI SKU ID = 535479Carrier ID = 29 Carrier Name = TataCurrent Modem Temperature = 30 degrees CelsiusEndpoint Port Map = 75router#Related Commands
show cellular security
Displays the modem lock state.
show controllers cellular
Displays EHWIC hardware- and driver-specific information.
show cellular network
To display information about the carrier network and service, use the show cellular network command in privileged EXEC mode.
show cellular unit network
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the outputs differ.
Examples
The following is a sample output for slot 0, WIC slot 0, and port 0:
router# show cellular 0/0/0 networkCurrent Service = 1xEV-DO (Rev A) and 1xRTTCurrent Roaming Status(1xRTT) = HOME, (HDR) = HOMECurrent Idle Digital Mode = HDRCurrent System Identifier (SID) = 4183Current Network Identifier (NID) = 87Current Call Setup Mode = Mobile IP onlyServing Base Station Longitude = 0 deg 0 min 0 secServing Base Station Latitude = 0 deg 0 min 0 secCurrent System Time = Tue Feb 6 15:16:9 2007Table 12 describes the significant fields shown in this output.
Related Commands
show cellular security
Displays the modem lock state.
show controllers cellular
Displays EHWIC hardware- and driver-specific information.
show cellular profile
To display the cellular profile information, use the show cellular profile command in privileged EXEC mode.
show cellular unit profile
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the output is different for each.
Examples
The following is a sample output for the show cellular profile command:
router# show cellular 0/0/0 profileElectronic Serial Number (ESN) = 0x6032688FModem activated = YESAccount Information:======================Activation Date: Not availablePhone Number (MDN) : 1234567890Mobile Station Identifier (MSID) : 1234567890Data Profile Info:=====================Number of data profiles configured : 2Current active data profile : 1Data Profile 0 Information==================================NAI (Network Access Identifier) = 6032688F@hcm.sprintpcs.comMN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 68.28.15.12Secondary Home Agent Address = 68.28.31.12Data Profile 1 Information (Active)==================================NAI (Network Access Identifier) = productmarketing432@sprintpcs.comMN-HA SS = SetMN-HA SPI = 1234MN-AAA SS = SetMN-AAA SPI = 1234Reverse Tunneling Preference = SetHome Address = 0.0.0.0Primary Home Agent Address = 68.28.81.76Secondary Home Agent Address = 68.28.89.76"*" Indicates the default profile.
Table 13 describes the output fields from the command.
show cellular radio
To display the cellular modem radio statistics, use the show cellular radio command in privileged EXEC mode.
show cellular unit radio {history {all | per-hour | per-min | per-sec}}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the output is different for each.
Examples
The following is a sample output for the show cellular radio command:
router# show cellular 0/0/0 radio1xRTT related info------------------Current RSSI = -95 dBm, ECIO = -6 dBmCurrent Channel Number = 50Current Channel State = AcquiredCurrent Band Class = Band Class 1HDR (1xEVDO) related info-------------------------Current RSSI = -88 dBm, ECIO = -2 dBmCurrent Channel Number = 25Current Band Class = Band Class 1Sector ID (Hex) = 0084:0AC0:0000:0000:000A:05DC:A801:1202Subnet Mask = 104, Color Code = 32, PN Offset = 240Rx gain control(Main) = 0 dBm, Diversity = UnavailableTx total power = -2 dBm, Tx gain adjust = 1536 dBmCarrier to interference (C/I) ratio = 2Table 14 describes the significant fields shown in this output.
Related Commands
show cellular all
Displays the consolidated information about the modem.
show controllers cellular
Displays EHWIC-hardware and driver-specific information.
show cellular security
To display the SIM status and modem lock state, use the show cellular security command in privileged EXEC mode.
show cellular unit security
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
The command usage is the same for Global System for Mobile Communications (GSM) and code division multiple access (CDMA), although the output is different for each.
Examples
The following is a sample output for the show cellular security command:
router# show cellular 0/0/0 securityModem PIN Security UNLOCKEDPower-up lock DISABLEDTable 15 describes the output for this command.
show cellular sms
To display SMS statistics, including the number of incoming and outgoing messages, use the show cellular sms command in privileged EXEC mode.
show cellular unit sms
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example displays the SMS statistics for the show cellular sms command:
router# show cellular 0/0/0 smsc1941#show cellular 0/0/0 smsSMS Service is not availableNumber of outgoing SMS pending = 0c1941#show cellular 0/1/0 smsIncoming Message Information----------------------------SMS stored in modem = 5SMS archived since booting up = 0Total SMS deleted since booting up = 0Storage records allocated = 99Storage records used = 5Number of callbacks triggered by SMS = 0Number of successful archive since booting up = 0Number of failed archive since booting up = 0Outgoing Message Information----------------------------Total SMS sent successfully = 0Total SMS send failure = 0Number of outgoing SMS pending = 0Number of successful archive since booting up = 0Number of failed archive since booting up = 0Last Outgoing SMS Status = SUCCESSSMS-Send-Status:Error Class = 0x0Cause Code = 0x0SMS Archive URL = ftp://username:password@192.168.1.3/SMS_archiveRelated Commands
show controllers cellular
To display high-speed WAN interface card (EHWIC) hardware and driver-specific information, use the show controllers cellular command in privilege EXEC mode.
show controllers cellular unit
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privilege EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
Use this command to capture the output for debugging or troubleshooting purposes only.
Related Commands
show interfaces cellular
Displays statistics for the cellular interfaces.
show run interface cellular
Displays the current running configuration for the cellular interface.
show interfaces cellular
To display statistics for the cellular interface, use the show interfaces cellular command in privileged EXEC mode.
show interfaces cellular unit
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Usage Guidelines
When you enter this command, encapsulation should be PPP and all signals, such as DCD, DSR, DTR, RTS, and CTS, should be up during normal operation.
Examples
The following example shows the output for the show interfaces cellular command:
router# show int cellular 0/0/0Cellular0/0/0 is up (spoofing), line protocol is up (spoofing)Hardware is EVDO Rev A/Rel 0/1xRTT-800/1900MHz / SPInternet address will be negotiated using IPCPMTU 1500 bytes, BW 9 Kbit, DLY 100000 usec,reliability 255/255, txload 1/255, rxload 1/255Encapsulation PPP, LCP Closed, loopback not setKeepalive not setLast input never, output never, output hang neverLast clearing of "show interface" counters neverInput queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0Queueing strategy: weighted fairOutput queue: 0/1000/64/0 (size/max total/threshold/drops)Conversations 0/0/16 (active/max active/max total)Reserved Conversations 0/0 (allocated/max allocated)Available Bandwidth 6 kilobits/sec30 second input rate 0 bits/sec, 0 packets/sec30 second output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort0 packets output, 0 bytes, 0 underruns0 output errors, 0 collisions, 0 interface resets0 output buffer failures, 0 output buffers swapped out0 carrier transitionsDCD=up DSR=up DTR=up RTS=up CTS=upRelated Commands
show run interface cellular
To see the current running configuration for the cellular interface, use the show run interface cellular command in privileged EXEC mode.
show run interface cellular unit
Syntax Description
unit
(EHWIC) Router slot, WIC slot, and port separated by slashes (for example, 0/1/0).
(Fixed platform) The number 0.
Command Modes
Privileged EXEC (#)
Command History
12.4(11)XV
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
Examples
The following example shows the output for the show run interface cellular command:
router# show running-config interface cellular 0/0/0interface Cellular0/0/0ip address negotiatedip access-group 10 outip nat outsideip virtual-reassemblyencapsulation pppno ip mroute-cacheload-interval 30dialer in-banddialer idle-timeout 2147483dialer string cdmadialer-group 2async mode interactiveno peer default ip addressfair-queueppp ipcp dns requestrouting dynamicend router#Related Commands
show controllers cellular
Displays EHWIC hardware- and driver-specific information.
show interfaces cellular
Displays statistics for the cellular interfaces.
Troubleshooting
This section provides the necessary background information and resources available for troubleshooting Cisco EHWIC-3G-EVDO issues.
•
•
Verifying Data Call Setup
To verify the data call setup, follow these steps:
Step 1
Step 2
•
•
•
•
•
•
•
•
Step 3
Checking Signal Strength
If the Received Signal Strength Indication (RSSI) level is very low (for example, if it is less than -110 dBm), follow these steps:
Step 1
Step 2
Step 3
Verifying Service Availability
The following is a sample output for the show cellular all command for a scenario where the antenna is disconnected and a modem data profile has not been created. The errors in this case have been highlighted with >>>>>>>:
3825_CDMA_3# show cellular 0/3/0 allLoad for five secs: 0%/0%; one minute: 0%; five minutes: 1%Time source is hardware calendar, 19:40:43.239 UTC Wed Nov 8 2006Hardware Information====================Modem Firmware Version = H1_0_0_7MCAP G:/WS/Modem Firmware built = 10/26/06Hardware Version = 1.0International Mobile Subscriber Identity (IMSI) = <specific sim number>International Mobile Equipment Identity (IMEI) = <specific modem number>Factory Serial Number (FSN) = X2819460388100DModem Status = OnlineCurrent Modem Temperature = 38 deg C, State = NormalProfile Information====================* - Default profile >>>>>>>> no profile here.Data Connection Information===========================Profile 1, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 2, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 3, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 4, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 5, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 6, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 7, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 8, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 9, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 10, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 11, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 12, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 13, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 14, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 15, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateProfile 16, Packet Session Status = INACTIVEInactivity Reason = Normal inactivate stateNetwork Information===================Current Service Status = No service, Service Error = None >>>>>>> no service means not connected to the network.Current Service = CombinedPacket Service = NonePacket Session Status = InactiveCurrent Roaming Status = HomeNetwork Selection Mode = AutomaticCountry = USA, Network = CinglrMobile Country Code (MCC) = 310Mobile Network Code (MNC) = 380Location Area Code (LAC) = 6042Routing Area Code (RAC) = 255Cell ID = 0Primary Scrambling Code = 0PLMN Selection = AutomaticRadio Information=================Current Band = None, Channel Number = 0Current RSSI = -110 dBm >>>>>>> either no antenna, or bad antenna or out of network.Modem Security Information==========================Card Holder Verification (CHV1) = DisabledSIM Status = OKSIM User Operation Required = NoneNumber of Retries remaining = 3Successful Call Setup
The following is a sample output when a call is set up using a CHAT script. It shows a received IP address from the network. Call setup is successful and data path is open.
To troubleshoot the call setup, enable these debug commands:
•
•
•
•
•
3825_CDMA_3#Nov 8 20:04:42.295: CHAT0/3/0: Attempting async line dialer scriptNov 8 20:04:42.295: CHAT0/3/0: Dialing using Modem script: <carrier> & System script: noneNov 8 20:04:42.299: CHAT0/3/0: process startedNov 8 20:04:42.299: CHAT0/3/0: Asserting DTRNov 8 20:04:42.299: CHAT0/3/0: Chat script <carrier> started >>>>> chat script invokedNov 8 20:04:42.299: CHAT0/3/0: Sending string: atdt*98*1#Nov 8 20:04:42.299: CHAT0/3/0: Expecting string: CONNECTNov 8 20:04:42.343: CHAT0/3/0: Completed match for expect: CONNECTNov 8 20:04:42.343: CHAT0/3/0: Chat script <carrier> finished, status = Success >>>> successful communication with modemNov 8 20:04:42.395: TTY0/3/0: no timer type 1 to destroyNov 8 20:04:42.395: TTY0/3/0: no timer type 0 to destroyNov 8 20:04:42.395: TTY0/3/0: no timer type 2 to destroyNov 8 20:04:44.395: %LINK-3-UPDOWN: Interface Cellular0/3/0, changed state to upNov 8 20:04:44.395: Ce0/3/0 PPP: Using dialer call directionNov 8 20:04:44.395: Ce0/3/0 PPP: Treating connection as a calloutNov 8 20:04:44.395: Ce0/3/0 PPP: Session handle[7E000089] Session id[46]Nov 8 20:04:44.395: Ce0/3/0 PPP: Phase is ESTABLISHING, Active OpenNov 8 20:04:44.395: Ce0/3/0 PPP: No remote authentication for call-outNov 8 20:04:44.395: Ce0/3/0 LCP: O CONFREQ [Closed] id 75 len 16Nov 8 20:04:44.395: Ce0/3/0 LCP: ACCM 0x000A0000 (0x0206000A0000)Nov 8 20:04:44.395: Ce0/3/0 LCP: MagicNumber 0x179E8E46 (0x0506179E8E46)Nov 8 20:04:44.395: Ce0/3/0 LCP: I CONFREQ [REQsent] id 83 len 25Nov 8 20:04:44.395: Ce0/3/0 LCP: ACCM 0x00000000 (0x020600000000)Nov 8 20:04:44.395: Ce0/3/0 LCP: AuthProto CHAP (0x0305C22305)Nov 8 20:04:44.395: Ce0/3/0 LCP: MagicNumber 0x374C7C61 (0x0506374C7C61)Nov 8 20:04:44.395: Ce0/3/0 LCP: PFC (0x0702)Nov 8 20:04:44.395: Ce0/3/0 LCP: ACFC (0x0802)Nov 8 20:04:44.395: Ce0/3/0 LCP: O CONFREJ [REQsent] id 83 len 8Nov 8 20:04:44.395: Ce0/3/0 LCP: PFC (0x0702)Nov 8 20:04:44.395: Ce0/3/0 LCP: ACFC (0x0802)Nov 8 20:04:44.399: Ce0/3/0 LCP: I CONFACK [REQsent] id 75 len 16Nov 8 20:04:44.399: Ce0/3/0 LCP: ACCM 0x000A0000 (0x0206000A0000)Nov 8 20:04:44.399: Ce0/3/0 LCP: MagicNumber 0x179E8E46 (0x0506179E8E46)Nov 8 20:04:44.399: Ce0/3/0 LCP: I CONFREQ [ACKrcvd] id 84 len 21Nov 8 20:04:44.399: Ce0/3/0 LCP: ACCM 0x00000000 (0x020600000000)Nov 8 20:04:44.399: Ce0/3/0 LCP: AuthProto CHAP (0x0305C22305)Nov 8 20:04:44.399: Ce0/3/0 LCP: MagicNumber 0x374C7C61 (0x0506374C7C61)Nov 8 20:04:44.399: Ce0/3/0 LCP: O CONFACK [ACKrcvd] id 84 len 21Nov 8 20:04:44.399: Ce0/3/0 LCP: ACCM 0x00000000 (0x020600000000)Nov 8 20:04:44.399: Ce0/3/0 LCP: AuthProto CHAP (0x0305C22305)Nov 8 20:04:44.399: Ce0/3/0 LCP: MagicNumber 0x374C7C61 (0x0506374C7C61)Nov 8 20:04:44.399: Ce0/3/0 LCP: State is OpenNov 8 20:04:44.399: Ce0/3/0 PPP: Phase is AUTHENTICATING, by the peerNov 8 20:04:44.403: Ce0/3/0 CHAP: I CHALLENGE id 1 len 35 from "UMTS_CHAP_SRVR"Nov 8 20:04:44.403: Ce0/3/0 CHAP: Using hostname from interface CHAPNov 8 20:04:44.403: Ce0/3/0 CHAP: Using password from interface CHAPNov 8 20:04:44.403: Ce0/3/0 CHAP: O RESPONSE id 1 len 40 from "<username configured on the cellular interface>"Nov 8 20:04:44.407: Ce0/3/0 CHAP: I SUCCESS id 1 len 4Nov 8 20:04:44.407: Ce0/3/0 PPP: Phase is FORWARDING, Attempting ForwardNov 8 20:04:44.407: Ce0/3/0 PPP: Phase is ESTABLISHING, Finish LCPNov 8 20:04:44.407: Ce0/3/0 PPP: Phase is UP>>>>> pap/chap succeededNov 8 20:04:44.407: Ce0/3/0 IPCP: O CONFREQ [Closed] id 1 len 22Nov 8 20:04:44.407: Ce0/3/0 IPCP: Address 0.0.0.0 (0x030600000000)Nov 8 20:04:44.407: Ce0/3/0 IPCP: PrimaryDNS 0.0.0.0 (0x810600000000)Nov 8 20:04:44.407: Ce0/3/0 IPCP: SecondaryDNS 0.0.0.0 (0x830600000000)Nov 8 20:04:44.407: Ce0/3/0 PPP: Process pending ncp packetsNov 8 20:04:45.411: Ce0/3/0 IPCP: I CONFNAK [REQsent] id 1 len 16Nov 8 20:04:45.411: Ce0/3/0 IPCP: PrimaryDNS 10.11.12.13 (0x81060A0B0C0D)Nov 8 20:04:45.411: Ce0/3/0 IPCP: SecondaryDNS 10.11.12.14 (0x83060A0B0C0E)Nov 8 20:04:45.411: Ce0/3/0 IPCP: O CONFREQ [REQsent] id 2 len 22Nov 8 20:04:45.411: Ce0/3/0 IPCP: Address 0.0.0.0 (0x030600000000)Nov 8 20:04:45.411: Ce0/3/0 IPCP: PrimaryDNS 10.11.12.13 (0x81060A0B0C0D)Nov 8 20:04:45.411: Ce0/3/0 IPCP: SecondaryDNS 10.11.12.14 (0x83060A0B0C0E)Nov 8 20:04:45.459: Ce0/3/0 IPCP: I CONFREQ [REQsent] id 25 len 4Nov 8 20:04:45.459: Ce0/3/0 IPCP: O CONFACK [REQsent] id 25 len 4Nov 8 20:04:45.459: Ce0/3/0 IPCP: I CONFNAK [ACKsent] id 2 len 22Nov 8 20:04:45.459: Ce0/3/0 IPCP: Address 166.138.186.119 (0x0306A68ABA77)Nov 8 20:04:45.459: Ce0/3/0 IPCP: PrimaryDNS 66.102.163.231 (0x81064266A3E7)Nov 8 20:04:45.459: Ce0/3/0 IPCP: SecondaryDNS 66.102.163.232 (0x83064266A3E8)Nov 8 20:04:45.459: Ce0/3/0 IPCP: O CONFREQ [ACKsent] id 3 len 22Nov 8 20:04:45.459: Ce0/3/0 IPCP: Address 166.138.186.119 (0x0306A68ABA77)Nov 8 20:04:45.459: Ce0/3/0 IPCP: PrimaryDNS 66.102.163.231 (0x81064266A3E7)Nov 8 20:04:45.459: Ce0/3/0 IPCP: SecondaryDNS 66.102.163.232 (0x83064266A3E8)Nov 8 20:04:45.463: Ce0/3/0 IPCP: I CONFACK [ACKsent] id 3 len 22Nov 8 20:04:45.463: Ce0/3/0 IPCP: Address 166.138.186.119 (0x0306A68ABA77)Nov 8 20:04:45.463: Ce0/3/0 IPCP: PrimaryDNS 66.102.163.231 (0x81064266A3E7)Nov 8 20:04:45.463: Ce0/3/0 IPCP: SecondaryDNS 66.102.163.232 (0x83064266A3E8)Nov 8 20:04:45.463: Ce0/3/0 IPCP: State is OpenNov 8 20:04:45.463: Ce0/3/0 IPCP: Install negotiated IP interface address 166.138.186.119Modem Troubleshooting Using the Diagnostic Port
The RJ-45 port on the faceplate of the 3G EHWIC provides access to the debug port on the Sierra Wireless modem. By connecting an industry-standard diagnostic tool like Qualcomm CAIT/QXDM or Spirent UDM to this port, you can perform radio-level diagnostics and traffic monitoring on the modem.
Use the following test commands to enable/disable the DM port:
router# test cell-hwic 0/1/0 dm-port local {on | off | speed}router# test cell-hwic 0/1/0 dm-port remote {on | off}For example, to enable the DM port, use one of these commands:
router# test cell-hwic 0/1/0 dm-port local onrouter# test cell-hwic 0/1/0 dm-port remote onThe cable used to connect the PC/Laptop running the diagnostic tool is the standard Cisco router console cable (RJ-45 to DB-9).
Note
Additional References
Related Documents
Cisco 880 Series Integrated Service Router configuration
•
•
Cisco 800 Series Integrated Service Router installation
Release notes
•
(EVDO Rev A)•
Standards
MIBs
RFCs
No new or modified RFCs are supported, and support for existing RFCs has not been modified.
—
Technical Assistance
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2011-2012 Cisco Systems, Inc. All rights reserved.
Feedback