Cisco 4000 Series Integrated Services Routers Overview
The Cisco 4000 Series ISRs are modular routers with LAN and WAN connections that can be configured by means of interface modules, including Cisco Enhanced Service Modules (SM-Xs), and Network Interface Modules (NIMs).
The following table lists the router models that belong to the Cisco 4000 Series ISRs.
Cisco 4400 Series ISR |
Cisco 4300 Series ISR |
Cisco 4200 Series ISR |
---|---|---|
Cisco 4431 ISR |
Cisco 4321 ISR |
Cisco 4221 ISR |
Cisco 4451-X ISR |
Cisco 4331 ISR |
|
Cisco 4461 ISR |
Cisco 4351 ISR |
System Requirements
The following are the minimum system requirements:
Note |
There is no change in the system requirements from the earlier releases. |
-
Memory: 4 GB DDR3 up to 32 GB
-
Hard Drive: 200 GB or higher (Optional). The hard drive is only required for running services such as Cisco ISR-WAAS.
-
Flash Storage: 4 GB to 32 GB
-
NIMs and SM-Xs: Modules (Optional)
-
NIM SSD (Optional)
For more information, see the Cisco 4000 Series ISRs Data Sheet.
Note |
For more information on the Cisco WAAS IOS-XE interoperability, refer to the WAAS release notes: https://www.cisco.com/c/en/us/support/routers/wide-area-application-services-waas-software/products-release-notes-list.html. |
Determining the Software Version
You can use the following commands to verify your software version:
-
For a consolidated package, use the show version command
-
For individual sub-packages, use the show version installed command
Upgrading to a New Software Release
To install or upgrade, obtain a Cisco IOS XE Amsterdam 17.3.1 consolidated package (image) from Cisco.com. You can find software images at http://software.cisco.com/download/navigator.html. To run the router using individual sub-packages, you also must first download the consolidated package and extract the individual sub-packages from a consolidated package.
Note |
When you upgrade from one Cisco IOS XE release to another, you may see %Invalid IPV6 address error in the console log file. To rectify this error, enter global configuration mode, and re-enter the missing IPv6 alias commands and save the configuration. The commands will be persistent on subsequent reloads. |
For more information on upgrading the software, see the How to Install and Upgrade the Software section of the Software Configuration Guide for the Cisco 4000 Series ISRs.
Recommended Firmware Versions
The following table lists the recommended ROMMON and CPLD versions for Cisco IOS XE 17.2.x onwards releases.
Cisco 4000 Series ISRs |
Existing ROMMON |
Cisco Field-Programmable Devices |
CCO URL for the CPLD Image |
---|---|---|---|
Cisco 4461 ISR |
16.12(2r) |
21102941 |
|
Cisco 4451-X ISR |
16.12(2r) |
19042950 |
|
Cisco 4431 ISR |
16.12(2r) |
19042950 |
|
Cisco 4351 ISR |
16.12(2r) |
19040541 |
|
Cisco 4331 ISR |
16.12(2r) |
19040541 |
|
Cisco 4321 ISR |
16.12(2r) |
19040541 |
|
Cisco 4221 ISR |
16.12(2r) |
19042420 |
Note |
Upgrading Field-Programmable Hardware Devices
The hardware-programmable firmware is upgraded when Cisco 4000 Series ISR contains an incompatible version of the hardware-programmable firmware. To do this upgrade, a hardware-programmable firmware package is released to customers.
Generally, an upgrade is necessary only when a system message indicates one of the field-programmable devices on the Cisco 4000 Series ISR needs an upgrade, or a Cisco technical support representative suggests an upgrade.
From Cisco IOS XE Release 3.10S onwards, you must upgrade the CPLD firmware to support the incompatible versions of the firmware on the Cisco 4000 Series ISR. For upgrade procedures, see the Upgrading Field-Programmable Hardware Devices for Cisco 4000 Series ISRs.
Feature Navigator
You can use Cisco Feature Navigator to find information about feature, platform, and software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on cisco.com is not required.
New and Changed Information
New and Changed Software Features in Cisco IOS XE 17.3.8a
There are no new features in this release. This release provides a fix for CSCwh87343: Cisco IOS XE Software Web UI Privilege Escalation Vulnerability. For more information, see the Security Advisory: cisco-sa-iosxe-webui-privesc-j22SaA4z.
New and Changed Software Features in Cisco IOS XE 17.3.8
There are no new software features in this release.
New and Changed Software Features in Cisco IOS XE 17.3.7
There are no new software features in this release.
New and Changed Software Features in Cisco IOS XE 17.3.6
There are no new software features in this release.
New and Changed Software Features in Cisco IOS XE 17.3.5
There are no new software features in this release.
New and Changed Software Features in Cisco IOS XE 17.3.4
There are no new software features in this release.
New Hardware Features in Cisco IOS XE Amsterdam 17.3.3
There are no new hardware features for this release.
New and Changed Software Features in Cisco IOS XE 17.3.3
The following features are supported by the Cisco 4000 Series Integrated Services Routers for Cisco IOS XE Amsterdam 17.3.3:
-
Smart Software Manager On-Prem (SSM On-Prem) Support for Smart Licensing Using Policy: SSM On-Prem is an asset manager, which works in conjunction with CSSM. It enables you to administer products and licenses on your premises instead of having to directly connect to CSSM.
Here, a product instance is connected to SSM On-Prem, and SSM On-Prem becomes the single point of interface with CSSM. The product instance can be configured to push the required information to SSM On-Prem. Alternatively, SSM On-Prem can be set-up to pull the required information from a product instance at a configurable frequency. After usage information is available in SSM On-Prem, you must synchronize the same with CSSM, to ensure that the product instance count, license count and license usage information is the same on both, CSSM and SSM On‐Prem. Offline and online options are available for synchronization between CSSM and SSM On‐Prem.
Minimum Required SSM On-Prem Version: Version 8, Release 202102
Minimum Required Cisco IOS XE Version: Cisco IOS XE Amsterdam 17.3.3
For more information, see Smart Licensing Using Policy for Cisco Enterprise Routing Platforms.
New Hardware Features in Cisco IOS XE Amsterdam 17.3.2
The following hardware is supported by the Cisco 4000 Series Integrated Services Routers for Cisco IOS XE Amsterdam 17.3.2.
-
NIM-PVDM is the next-generation digital signal processor (DSP) module to utilize a PVDM4 chip for IP media services. This module enables the Cisco 4000 Series Integrated Services Routers to provide rich-media capabilities, such as high-density voice connectivity, conferencing, transcoding, media optimization, transrating, and secure voice for Cisco Unified Communications solutions.
For information on the hardware features supported on the NIM-PVDM, refer to the Cisco Packet Voice Digital Signal Processor Modules for Cisco Unified Communications Solutions datasheet.
New and Changed Software Features in Cisco IOS XE 17.3.2
-
Smart Licensing Using Policy—An enhanced version of Smart Licensing with the overall objective of providing a licensing solution that does not interrupt the operations of your network but also enables a compliance relationship to account for the hardware and software licenses you purchase and use.
With this licensing model, you do not have to complete any licensing-specific operations such as registering or generating keys before you start using the software and the licenses that are tied to it. License usage is recorded on your device with timestamps and the required workflows can be completed at a later date.
Multiple options are available for license usage reporting which depends on the topology you implement. You can use the Cisco Smart Licensing Utility (CSLU) Windows application or report usage information directly to CSSM. A provision for offline reporting for air-gapped networks where you download usage information and upload to CSSM is also available.
For a more detailed overview on Cisco Licensing, go to https://cisco.com/go/licensingguide.
-
Cisco DNA Support for Smart Licensing Using Policy — Cisco DNA Center supports Smart Licensing Using Policy functionality starting with Cisco DNA Center Release 2.2.2. The corresponding minimum required Cisco IOS XE Release for this platform is 17.3.2.
Implement the “Connected to CSSM Through a Controller” topology to have Cisco DNA Center manage a product instance. When you do, the product instance records license usage, but it is the Cisco DNA Center that initiates communication with the product instance to retrieve and report usage to Cisco Smart Software Manager (CSSM) and returns the acknowledgement (RUM ACK).
In order to meet reporting requirements, Cisco DNA Center provides ad hoc or on-demand reporting, as well as scheduled reporting options. Cisco DNA Center also provides workflows for the installation and removal of the Smart Licensing Authorization Code (SLAC) for a product instance, if applicable.
Note
On the Cisco DNA Center GUI, you can generate a SLAC only for HSECK9 licenses, and only for certain product instances. See the configuration guide for details.
Note
Starting with Cisco IOS XE Amsterdam 17.3.2 release, with the introduction of Smart Licensing Using Policy, even if you configure a hostname for a product instance or device, only the Unique Device Identifier (UDI) is displayed. This change in the display can be observed in all licensing utilities and user interfaces where the hostname was displayed in earlier releases. It does not affect any licensing functionality. There is no workaround for this limitation.The licensing utilities and user interfaces that are affected by this limitation include only the following:
-
Cisco Smart Software Manager (CSSM),
-
Cisco Smart License Utility (CSLU), and
-
Smart Software Manager On-Prem (SSM On-Prem).
-
New Hardware Features in Cisco IOS XE Amsterdam 17.3.1a
There are no new hardware features for this release.
New and Changed Software Features in Cisco IOS XE 17.3.1a
The following features are supported by the Cisco 4000 Series Integrated Services Routers for Cisco IOS XE Amsterdam 17.3.1a:
Note |
Cisco IOS XE Amsterdam 17.3.1a is the first release for Cisco 4000 Series ISRs in the Cisco IOS XE Amsterdam 17.3.1 release series. |
Note |
Some YANG models are not fully compliant with all the IETF guidelines. The errors and warnings shown while executing pyang with -–lint flag is currently deemed to be non-critical as they do not impact the semantic of the models or prevent the models from being used as part of the toolchains. To determine the issues with the models, run the check-models.sh script with --lint flag enabled. It is recommended to ignore LEAFREF_IDENTIFIER_NOT_FOUND and STRICT_XPATH_FUNCTIONS errors types when running pyang for validation as they are non-critical errors and does not impact the YANG model functionality. |
-
Configure IP Multicast over Unidirectional Links for PIM—Unicast and multicast routing protocols forward data on interfaces from which they have received routing control information- this requires a bidirectional link. However, some network links are unidirectional, where the physical send-only interface is on the upstream router and the physical receive-only interface is on the downstream router. To control routing information in these unidirectional environments, you need to enable the IP multicast over UDL functionality. To enable this functionality, you can now configure a UDL routing tunnel as a unidirectional generic routing encapsulation (GRE) tunnel and map this to a one-way satellite link, which in turn enables the associated unicast and multicast routing protocols to treat the UDL as a bidirectional link.
-
Configuring Client-Initiated Dial-In VPDN Tunneling—Starting from release 17.3, IPv6 and dual-stack enabling is supported over Virtual-PPP and L2TPv2.
-
Support for openconfig-lldp 0.2.1: From the Cisco IOS XE Amsterdam 17.3.1 release, the openconfig-lldp 0.2.1 is supported. No additional configuration is required.
-
CUBE: Up to 100 VRF Instances—With this feature enhancement, CUBE supports up to 100 VRFs. Each of the VRFs supports up to 10 different RTP port ranges.
-
CUBE: Dial Peer Binding with Live Traffic—The Live Bind feature allows you to either change or add binding on a dial-peer that does not have any active calls, while other dial-peers with the same binding has active calls.
-
CUBE: Media Proxy Multi-forking using SIPREC—With this feature, the SIPREC-based CUBE Media Proxy solution supports forking to multiple recorders.
-
CUBE: OPUS Codec Negotiation—With this feature, support is introduced for OPUS audio codec with CUBE.
-
CUBE: TLS Server Name Indication (SNI) - RFC6066—With this feature, support is introduced for Server Name Indication (SNI). SNI is a TLS extension that allows a TLS client to indicate the name of the server that it is trying to connect during the initial TLS handshake process.
-
CUBE: Consumption of INVITE with Replaces—With this feature, new behavior is introduced for INVITE with REPLACES header consume scenario in CUBE.
-
MACsec Encryption on Cisco SM-X-16G4M2X or SM-X-40G8M2X EtherSwitch Service Module—MACsec encryption on Cisco SM-X-16G4M2X or SM-X-40G8M2X EtherSwitch Service Module: The Cisco SM-X-16G4M2X or SM-X-40G8M2X EtherSwitch Service module supports 802.1AE encryption with MACsec KeyAgreement (MKA) on switch-to-host links and helps in encryption of traffic between the switch and host device.
-
Min-flow-rate CommandSet the minimum flow rate bandwidth threshold for the Dynamic Application Policy Routing instance.
-
New Cipher Suites for IP SSH Client and Server Algorithm—You can configure the HMAC algorithm of HMAC-SHA2-256-ETM@openssh.com or HMAC-SHA2-512-ETM@openssh.com as a cryptographic algorithm. These cipher suites can be used with the ip ssh client.
-
Show IP CEF Command—To display all information of CEF, run the show ip cef command. This command in turn displays the output of the following commands therefore avoiding the need to run each of these commands individually.
-
Show Platform Resources Command—The existing show platform recourses command now includes the following extension keywords to help you gather more information on platform resource utilization: R0, R0 cpu, R0 memory, exmem, datapath, and datapath oversubscriptions.
-
Show Packet Tracer Command—The output of the show platform packet-trace command now includes additional trace information for packets that originate from IOSd or have destination marked for IOSd or other BinOS processes.
-
Show Platform Hardware QFP Active Datapath Utilization Command—The output of the show platform hardware qfp active datapath utilization command now includes crypto and I/O utilization of the device.
Configure the Router for Web User Interface
This section explains how to configure the router to access Web User Interface. Web User Interface requires the following basic configuration to connect to the router and manage it.
-
An HTTP or HTTPs server must be enabled with local authentication.
-
A local user account with privilege level 15 and accompanying password must be configured.
-
Vty line with protocol SSH/Telnet must be enabled with local authentication. This is needed for interactive commands.
-
For more information on how to configure the router for Web User Interface, see Cisco 4000 Series ISRs Software Configuration Guide, Cisco IOS XE 17.
Entering the Configuration Commands Manually
To enter the Cisco IOS commands manually, complete the following steps:
Before you begin
If you do not want to use the factory default configuration because the router already has a configuration, or for any other reason, you can use the procedure in this section to add each required command to the configuration.
Procedure
Step 1 |
Log on to the router through the Console port or through an Ethernet port. |
Step 2 |
If you use the Console port, and no running configuration is present in the router, the Setup command Facility starts automatically, and displays the following text:
Enter no so that you can enter Cisco IOS CLI commands directly. If the Setup Command Facility does not start automatically, a running configuration is present, and you should go to the next step. |
Step 3 |
When the router displays the user EXEC mode prompt, enter the enable command, and the enable password, if one is configured, as shown in the following example:
|
Step 4 |
Enter config mode by entering the configure terminal command, as shown in the following example.
|
Step 5 |
Using the command syntax shown, create a user account with privilege level 15. |
Step 6 |
If no router interface is configured with an IP address, configure one so that you can access the router over the network. The following example shows the interface GigabitEthernet 0/0/0 configured.
|
Step 7 |
Configure the router as an http server for nonsecure communication, or as an https server for secure communication. To configure the router as an http server, enter the ip http server command shown in the example:
|
Step 8 |
Configure the router for local authentication, by entering the ip http authentication local command, as shown in the example:
|
Step 9 |
Configure the vty lines for privilege level 15. For nonsecure access, enter the transport input telnet command. For secure access, enter the transport input telnet ssh command. An example of these commands follows:
|
Resolved and Open Bugs
This section provides information about the bugs in Cisco 4000 Series Integrated Services Routers and describe unexpected behavior. Severity 1 bugs are the most serious bugs. Severity 2 bugs are less serious. Severity 3 bugs are moderate bugs. This section includes severity 1, severity 2, and selected severity 3 bugs.
The open and resolved bugs for this release are accessible through the Cisco Bug Search Tool. This web-based tool provides you with access to the Cisco bug tracking system, which maintains information about bugs and vulnerabilities in this product and other Cisco hardware and software products. Within the Cisco Bug Search Tool, each bug is given a unique identifier (ID) with a pattern of CSCxxNNNNN, where x is any letter (a-z) and N is any number (0-9). The bug IDs are frequently referenced in Cisco documentation, such as Security Advisories, Field Notices and other Cisco support documents. Technical Assistance Center (TAC) engineers or other Cisco staff can also provide you with the ID for a specific bug. The Cisco Bug Search Tool enables you to filter the bugs so that you only see those in which you are interested.
In addition to being able to search for a specific bug ID, or for all bugs in a product and release, you can filter the open and/or resolved bugs by one or more of the following criteria:
-
Last modified date
-
Status, such as fixed (resolved) or open
-
Severity
-
Support cases
You can save searches that you perform frequently. You can also bookmark the URL for a search and email the URL for those search results.
Note |
If the bug that you have requested cannot be displayed, this may be due to one or more of the following reasons: the bug ID does not exist, the bug does not have a customer-visible description yet, or the bug has been marked Cisco Confidential. |
Using the Cisco Bug Search Tool
For more information about how to use the Cisco Bug Search Tool , including how to set email alerts for bugs and to save bugs and searches, see Bug Search Tool Help & FAQ .
Before You Begin
Note |
You must have a Cisco.com account to log in and access the Cisco Bug Search Tool . If you do not have one, you can register for an account. |
SUMMARY STEPS
- In your browser, navigate to the Cisco Bug Search Tool .
- If you are redirected to a Log In page, enter your registered Cisco.com username and password and then, click Log In.
- To search for a specific bug, enter the bug ID in the Search For field and press Enter.
- To search for bugs related to a specific software release, do the following:
- To see more content about a specific bug, you can do the following:
- To restrict the results of a search, choose from one or more of the following filters:
DETAILED STEPS
Step 1 |
In your browser, navigate to the Cisco Bug Search Tool . |
||||||||||||
Step 2 |
If you are redirected to a Log In page, enter your registered Cisco.com username and password and then, click Log In. |
||||||||||||
Step 3 |
To search for a specific bug, enter the bug ID in the Search For field and press Enter. |
||||||||||||
Step 4 |
To search for bugs related to a specific software release, do the following: |
||||||||||||
Step 5 |
To see more content about a specific bug, you can do the following:
|
||||||||||||
Step 6 |
To restrict the results of a search, choose from one or more of the following filters:
Your search results update when you choose a filter. |
Resolved and Open Bugs in Cisco 4000 Series Integrated Services Routers
Open Caveats - Cisco IOS XE 17.3.8a
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
IPv6 DMVPN - NBMA address not getting preserved. |
|
FlexVPN: Stale client routes stuck in RIB on FlexServer. |
|
CISCO-CLASS-BASED-QOS-MIB does not work with LTE Cellular interface on device after reload. |
|
Device crashes due to %IDMGR-3-INVALID_ID: bad id in id_delete during session roaming. |
|
Device crash with crashinfo files were generated with Segmentation fault, Process IPSEC key engine. |
|
IOS XE router may experience unexpected reset while executing show utd engine standard statistics. |
|
ISG: initiator unclassified ip-address LQipv4 command has no effect. |
|
EWC HA pair expereincing IOS tracebacks, followed by KEYMAN crash. |
|
Inter-VRFroute leaking not working and packet drop seen due to Ipv4Unclassified. |
|
Dataplane memory utilization issue - 97% QFP DRAM memory utilization. |
|
Crash when using dial-peer groups with STCAPP. |
|
Auto-update cycle incorrectly deletes certificates. |
|
Subscriber session getting stuck and needs clearing it manually. |
|
Device template attachment causes PPPoE commands to be removed from ethernet interface. |
|
CPP unexpected reboot while freeing CVLA chunk. |
|
CSDL failure: IPSec QM use of DES by encrypt process is denied. |
|
After configuring match input-interface on class-map, router goes into a reboot loop. |
|
VMWI race condition causes no ringing for analog phones. |
|
Traceback: fman_fp_image core after clearing packet-trace conditions. |
|
Device crashes due to cpp_cp_svr fault on fp_0_0 (rc=134) when applying umbrella dnscrypt to profile. |
|
Router traceback and reload when different encapsulation used on xconnect interfaces. |
|
No dial tone on analog phones due to DSP going into Power Denial state. |
Resolved Caveats - Cisco IOS XE 17.3.8a
All resolved bugs for this release are available in the Cisco Bug Search Tool.
Bug ID |
Description |
---|---|
Cisco IOS XE Software Web UI Privilege Escalation Vulnerability. For more information, see Security Advisory: cisco-sa-iosxe-webui-privesc-j22SaA4z |
Open Caveats - Cisco IOS XE Amsterdam 17.3.8
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
IPv6 DMVPN - NBMA address not getting preserved. |
|
FlexVPN: Stale client routes stuck in RIB on FlexServer. |
|
CISCO-CLASS-BASED-QOS-MIB does not work with LTE Cellular interface on device after reload. |
|
Device crashes due to %IDMGR-3-INVALID_ID: bad id in id_delete during session roaming. |
|
Device crash with crashinfo files were generated with Segmentation fault, Process IPSEC key engine. |
|
IOS XE router may experience unexpected reset while executing show utd engine standard statistics. |
|
ISG: initiator unclassified ip-address LQipv4 command has no effect. |
|
EWC HA pair expereincing IOS tracebacks, followed by KEYMAN crash. |
|
Inter-VRFroute leaking not working and packet drop seen due to Ipv4Unclassified. |
|
Dataplane memory utilization issue - 97% QFP DRAM memory utilization. |
|
Crash when using dial-peer groups with STCAPP. |
|
Auto-update cycle incorrectly deletes certificates. |
|
Subscriber session getting stuck and needs clearing it manually. |
|
Device template attachment causes PPPoE commands to be removed from ethernet interface. |
|
CPP unexpected reboot while freeing CVLA chunk. |
|
CSDL failure: IPSec QM use of DES by encrypt process is denied. |
|
After configuring match input-interface on class-map, router goes into a reboot loop. |
|
VMWI race condition causes no ringing for analog phones. |
|
Traceback: fman_fp_image core after clearing packet-trace conditions. |
|
Device crashes due to cpp_cp_svr fault on fp_0_0 (rc=134) when applying umbrella dnscrypt to profile. |
|
Router traceback and reload when different encapsulation used on xconnect interfaces. |
|
No dial tone on analog phones due to DSP going into Power Denial state. |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.8
There are no resolved caveats in this release.
Open Caveats - Cisco IOS XE Amsterdam 17.3.7
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
ISG: initiator unclassified ip-address LQipv4 command has no effect. |
|
After configuring match input-interface on class-map, router goes into a reboot loop. |
|
IPv6 DMVPN - NBMA address not getting preserved. |
|
CISCO-CLASS-BASED-QOS-MIB doesn't work with LTE Cellular interface after reload. |
|
ISG / Crashes due to %IDMGR-3-INVALID_ID: bad ID in id_delete during session roaming. |
|
Subscriber session getting stuck and needs clearing it manually. |
|
Router crashes due to CPUHOG when walking ciscoFlashMIB. |
|
EWC HA pair expereincing IOS tracebacks, followed by KEYMAN crash. |
|
Traceback: fman_fp_image core after clearing packet-trace conditions. |
|
Device link goes err-disabled due to link-flap after reloading peer device. |
|
Auto-update cycle incorrectly deletes certificates. |
|
Device template attachment causes PPPoE commands to be removed from ethernet interface. |
|
Dataplane memory utilization issue - 97% QFP DRAM memory utilization. |
|
CSDL failure: IPSec QM use of DES by encrypt proc is denied. |
|
VMWI race condition causes no ringing for analog phones. |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.7
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
Interface VLAN1 placed in shutdown state when configured with ip address pool. |
|
Intermittent double DTMF due to changing timestamp on a DTMF event. |
|
Device frequent reloads due to stuck thread in CPP. |
|
QFP crash when ZBFW configuration features log dropped-packets configuration. |
|
The router reload unexpectedly due to Cellular CNM process. |
|
EzPM (performance monitor) error logs may cause uCode crash due to congestion of IPC from DP to CP. |
|
QoS Classification not working for DSCP or ACL + MPLS EXP. |
|
ERROR info: Router configuration failed:interface Serial0/1/0:23 isdn switch-type primary-ntt. |
|
Router reloads unexpectedly during NHRP processing. |
|
DSPware 55.1.6 Release targeting v173_throttle. |
|
Device seeing out of service on Switch modules with new DC power supply. |
Open Caveats - Cisco IOS XE Amsterdam 17.3.6
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
IPv6 DMVPN - NBMA address not getting preserved. |
|
ICMP traceroute return packet not classified based on FW override port info. |
|
CISCO-CLASS-BASED-QOS-MIB doesn't work with LTE Cellular interface on device after reload. |
|
Crashes due to %IDMGR-3-INVALID_ID: bad id in id_delete during session roaming. |
|
NHRP messages tagged with incorrect MPLS labels - unable to establish shortcut. |
|
UTD: Exception in utd_logger.py due to missing extra-data in AMP alert. |
|
Removal of 'set reverse-route tag xxx' removes 'reverse-route' config from crypto map. |
|
When configration ip nat inside/outside on VASI intereface,ack/seq number abnormal. |
|
Platform rebooted unexpectedly with reason "LocalSoft". |
|
Platform QFP core due to NAT scaling issue. |
|
Device gets rebooted when Tunnel move across two egress interfaces with QoS MPoL policy config. |
|
ISG: initiator unclassified ip-address LQipv4 command has no effect. |
|
Device with NIM-ES2 "no igmp snooping vlan x" is not preserved after reload. |
|
EWC Ha pair expereincing IOS Tracebacks, followed by KEYMAN crash. |
|
LA LED turns green when just inserted SFP-10G-LR without cable connecting. |
|
%CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed due to ip rtp header-compression iphc-format. |
|
IR1101-K9 - RTSP Traffic not being rewritten by NAT. |
|
Router crashing when clearing a VPDN session. |
|
IKEv1 IPSec CAC (Call Admission Control) counter leak leading to %CRYPTO-4-IKE_DENY_SA_REQ. |
|
ISG: Number of lite sessions conversion in progress counter not decrementing on failed account-logon. |
|
NIM-LTE-EA No Data - requires subslot reload to recover. |
|
HSRP and VRRP Virtual IP address is not reachable. |
|
Unable to remove "switchport mode access" and "switchport nonegotiate" at the same time. |
|
Device crash for stuck threads in cpp on packet processing. |
|
X25 FRMR seen when switching from XOT to low speed serial. |
|
The router reload unexpectedly due to Cellular CNM process. |
|
DMVPN - after removing IPSec, traffic is dropped on a tunnel interface. |
|
CPP uCode crash due to ipc congestion from dp to cp. |
|
IOS-XE Device may experience an unexpected reset in "SNMP ENGINE" when polling cEigrpInterfaceEntry. |
|
Device template attachment causes pppoe commands to be removed from ethernet interface. |
|
CPP unexpected reboot while freeing CVLA chunk. |
|
Not triggering any alarms when RPM of a fan is 0. |
|
IKEv2 Deprecated Ciphers denied by Crypto Engine CDSL - PSB Security Compliance - DES, 3DES, DH1/2/5. |
|
Missing Mandatory Transform Type (ESN) in IKEv2 ESP Protocol. |
|
After configuring match input-interface on class-map, router goes into a reboot loop. |
|
Subscriber Session getting stuck and needs clearing manually. |
|
Link goes err-disabled due to link-flap after reloading peer device. |
|
GETVPN-ipv6 & LISP support. |
|
Traceback: fman_fp_image core after clearing packet-trace conditions. |
|
Device 5G light is blue when 4G LTE is in use. |
|
ZBFW : ARStandby drops seen on New Active during RG switchover. |
|
Router may crash due to Crypto IKMP process. |
|
CPA fail to send SIP update for AsmT before "maxTermToneAnalysis" expiration. |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.6
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
MACsec not working on subinterfaces using dot1q >255. |
|
IKEv2 fragmentation causes wrong message ID used for EAP authentication. |
|
IOS PKI client uses incorrect search filter for CRL retrieval using LDAPv3. |
|
Lack of MAC address in Inform Event message. |
|
IPSec Key Engine process holding memory continuously and not freeing up. |
|
Router rebooted de to watchdogs after issuing the commands sh crypto mib ipsec commands. |
|
CDP/LLDP not working when 10GE interface enabled with MACsec. |
|
Device reloads when group-range is configured under an interface Group-Async. |
|
Traffic is hitting wrong sequence in the data policy. |
|
SCCP auto-configuration issues with multiple protocols. |
|
After configuring match input-interface on class-map, router goes into a reboot loop. |
|
MGCP automatic configuration fails after IOS-XE upgrade. |
|
Platform abnormal Kerlog log is produced when port in shutdown state. |
|
NHRP process taking more CPU with ip nhrp redirect configured. |
|
ZBFW dropping return packets from tunnel post upgrade. |
|
Support IGMP on voice vlan. |
|
IP Device-tracking not functional with voice VLAN configured. |
|
Source address translation for multicast traffic fails with route-map. |
|
Appnav-XE connections are going as passthrough unsupported. |
|
Large number of IPSec tunnel flapping occurs when underlay is restored. |
|
IOS-XE: C11xx platforms running 17.x - crypto ipsec policy installation fails. |
|
NAT translations do not work for FTP traffic. |
|
Incorrect check of the TCP sequence number causing return ICMP error packets to drop (Thousandeyes). |
|
Registration of spoke fails with dissimilar capabilities w.r.t to HUB. |
|
Renewing hardware wan edge cert shows old cert serial/valid date in control local-properties. |
|
Interface comes up with only an SFP inserted. |
|
Secure key agent trace levels set to Noise by default. |
|
"Revocation-check crl none" does not failover to NONE DNAC-CA. |
|
Serial interface stuck in "line protocol is down" state after it went down and it is recovered. |
|
Observed crash with 17.3.1prd10 image. |
|
Keyman memory leak using public keys. |
|
Device fails to update sdn-network-infra-iwan key after 1 year. |
|
Nested IPSec tunnels encryption does not work as expected on platforms with crypto offload enabled. |
|
Sub-interface may not forward traffic after a reload. |
|
CRL verification failure result 400 Bad Request with DigiCert. |
|
Static mapping for the hub lost on one of the spokes. |
|
Packet Sanity failed for Resolution Reply on Spoke due to missing SMEF capability. |
|
FTP data traffic broken when UTD IPS enabled in both service VPN. |
Open Caveats - Cisco IOS XE Amsterdam 17.3.5
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
IPv6 DMVPN - NBMA address not getting preserved |
|
CUBE DTMF interworking fails from rtp-nte to OOB SIP methods |
|
Protocol specific change for base path |
|
Kernel crash with last reload reason "LocalSoftADR" |
|
NHRP messages tagged with incorrect MPLS labels - unable to establish shortcut |
|
Removing service-policy from the Zone-pair causes device crash |
|
Removal of 'set reverse-route tag xxx' removes 'reverse-route' config from crypto map |
|
ASR1001X gets rebooted when Tunnel move across two egress interfaces with QoS MPoL policy config |
|
Router rebooted de to watchdogs after issuing the commands sh crypto mib ipsec commands |
|
[SWI : #01080538 ] LTE is not reestablishing after reset of the modem |
|
ISR4K with NIM-ES2 "no igmp snooping vlan x" is not preserved after reload. |
|
Incorrect OMP Labels in On-Demand Tunnel H/S Topology |
|
MGCP automatic configuration fails after IOS-XE upgrade on ISR4k |
|
LA LED turns green when just inserted SFP-10G-LR on ISR4k without cable connecting |
|
%CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed due to ip rtp header-compression iphc-format |
|
crash observed at NHRP while using summary-map |
|
IKEv1 IPSec CAC (Call Admission Control) counter leak leading to %CRYPTO-4-IKE_DENY_SA_REQ |
|
Crash on cpp process when QoS policy configuration is being applied |
|
ngiolite: core generated after oir of SFP-10G-SR on ISR4461 |
|
Getting "%IOSXE_QFP-2-LOAD_EXCEED" on ISR4K by using code version "17.03.04a.0.5574" |
|
IOSd Nhrp core due to a segmentation fault when disabling PfR IWANs |
|
DMVPN - after removing IPSec, traffic is dropped on a tunnel interface |
|
Incorrect check of the TCP sequence number causing return ICMP error packets to drop (Thousandeyes) |
|
IOS-XE Device may experience an unexpected reset in "SNMP ENGINE" when polling cEigrpInterfaceEntry |
|
ISR4431 PWR-GE-POE-4400 looses VID and SN after upgrade |
|
Router may crash due to Crypto IKMP process |
|
C1100 Unexpected reboot with Critical process fman_fp_image fault on fp_0_0 |
|
Missing Mandatory Transform Type (ESN) in IKEv2 ESP Protocol |
|
EIO: Packets getting reassembled and are forwarded as it is to the Gigabit interface |
|
Device: sdn-network-infra-iwan key does not update successfully under network disruption situation |
|
GETVPN-ipv6 & LISP support on C900 platforms |
|
SCEP fails if AAAA DNS repy is received and source interface has no IPv6 address |
|
The router reload unexpectedly due to Cellular CNM process. |
|
FlexVPN per-user inline ACL from Radius not installed |
|
ZBFW : ARStandby drops seen on New Active during RG switchover |
|
intermittent SSH TCP checksum miscalculation while decrypting and processing the FlexVPN traffic |
|
CAT8300 nested IPSec tunnels encryption does not work as expected |
|
Router ISR unexpectedly rebooted due to local soft QFP0 Fatal Fault: Ucode process fault |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.5
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
ISR 4K running in sdwan controller mode experiencing module reload due to NGIO control packet loss |
|
VG450 Crashes Repeatedly in IOSd due to HTSP |
|
SCCP gateway auto configuration download results in an incomplete configuration. |
|
NAT TCP Load Balancing not working on IOS XE |
|
GETVPN: Clearing members on Key Server causing rekey processing failure on GMs |
|
VLAN IP config missing on bootup due to missing startup configs |
|
crypto ipsec security-association dummy leads to packet loss |
|
Prefetch CRL Download Fails |
|
Ucode crash observed at tw_bad_timer_bucket () at ../../../infra/tw_timer.c:918 |
|
DMVPN over DMVPN with IPSEC - return packets are dropped with BadIpChecksum |
|
A router may crash when processing an NHRP packet |
|
ISR4321 | After enabling "cts manual" the interfaces start flapping |
|
CVLA need to reserve at least 50M memory for low-end DRAM platform |
|
CPP ucode crash with route-map and overload at ipv4_nat_rmap_walk_find. |
|
Call Placing issue from SCCP phones |
|
PDP Type error on isr4k using Cellular 4G |
|
IKEv1/IKEv2 "show crypto session brief" output empty |
|
Static NAT conflicts/overwrites with Port-forwarding |
|
Console port goes unresponsive, reboot required to restore it. |
|
IOS-xe does not correlate indices properly with cellular radio band output |
|
Router does not boot on recent 16.X releases with large service policy applied on the interface. |
|
Hostname not allowed beginning with numbers |
|
memory leak with fman_cc process when SM-X-G4M2X module installed |
|
Poor DMVPN performance when used with IPSEC (Transport Mode) and GRE options are enabled |
|
Router may crash under ZBF configuration (cpp_cp_svr) |
|
ISR4461 crashed in SSLVPN stress test |
|
Crypto PKI-CRL-IO process crash when PKI trustpoint is being deleted |
|
Crash when getting cdspCardStatusEntry OID |
|
E1 configurations (under Serial interface) lost after reload. |
|
Curie: posix_printf does not work on COFF core in calo testbed |
|
IOS-XE unable to export elliptic curve key |
|
OSPFv3 adjacency won't come up after "ospfv3 authentication ipsec" is applied on Tunnel interface |
|
Crash seen on executing 'no ccm-manager sccp' |
|
Crash when issuing "show crypto isakmp peers config" |
|
tdm-group timeslot 31 failed to create/connect |
|
crypto ikev2 proposals are not processed separately |
|
Watchdog timeout due to Crypto IKMP |
Open Caveats - Cisco IOS XE Amsterdam 17.3.4a
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
DMVPN - after removing IPSec, traffic is dropped on a tunnel interface |
|
Data consistancy errors seen on configuring mac-sec on the underlay interface with ipsec configured |
|
unexpected reload due to Crypto IKEv2 process |
|
Watchdog timeout due to Crypto IKMP |
|
can not update local-address in a crypto keyring |
|
crypto ikev2 proposals are not processed separately |
|
cEdge-policy: set next-hop-ipv6 is not working next-hop-ip (ipv4) is working. |
|
Crash when issuing "show crypto isakmp peers config" |
|
IKE should have a mechanism to alert or mitigate resource exhaustion due to QM flooding |
|
"SNMP ENGINE" Crashes When Polling cEigrpInterfaceEntry MIB |
|
IKEv1 IPSec CAC (Call Admission Control) counter leak leading to %CRYPTO-4-IKE_DENY_SA_REQ |
|
Removal of 'set reverse-route tag xxx' removes 'reverse-route' config from crypto map |
|
Data-policy local-tloc with app-route is dropping packets when SLA is not met |
|
Cedge : Cloudexpress Office 365 probes are hitting 100% loss |
|
URL Filtering regex pattern match not working on large pattern |
|
cEdge QFP starts dropping traffic - UTD Service Node not healthy ident |
|
cEdge: High CPU usage due to Multicast and Data Policy configuration. |
|
Cisco 4451 ISR: Startup config lost for NIM-2GE-CU-SFP after upgrade to Amsterdam |
|
cEdge dropping packets [combination /16, /17 data prefix with multiple ports in policy] |
|
Unable to fetch eigrp prefix, nexthop, omptag, and route origin |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.4a
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
App-aware policy need to be honored when queuing is not set by localized policy |
|
Pre-mature session deletion leading to churn and lower TPS at scale |
|
BFD sessions go down on Service VPN after UTD is enabled on cEdge |
|
Cisco 4000 Series ISR LACP Configuration lost: channel-group X "mode active" gets removed on reload |
|
Multiple crashes cpp_cp_svr and qfp-ucode on 16.12.4 |
|
cEdge running 17.3.2 crashed - Critical software exception / IOSXE-WATCHDOG: Process = SNMP ENGINE |
|
SDWAN custom policy that does not looked to be programmed correctly on the cedge platform |
|
FW-4-ALERT_ON: (target:class)-():getting aggressive seen when no half open feature configed |
|
Wrong reload reason reflected after a power outage. |
|
Cisco 4400 ISR routing multicast packets out of order VASI-left in VRF RIB VASI-right in Global RIB |
|
DCHP offer frame getting dropped on cEdge ISR4431 due to Policy |
|
Removing and Adding Bulk ACL leads to dataplane programming failure |
|
Zone Based Firewall on cEdge router dropping web traffic with the reason Zone-pair without policy |
|
ISR Crash for CENT-MC-0 process |
|
cannot apply ciscosdwan.cfg due to vpg-log-server-acl ACL on VirtualPortGroup0 for logging |
|
Crash when TPOOL is updating and 'wr mem' is issues at same time |
|
ZBFW blocking ACK packets for applications using cloudexpress SaaS set to use a Gateway with synsent |
|
Cisco 4431 ISR/K9 rebooting due to CPP crashing becaue of UTD feature. |
|
"show sdwan policy service-path/tunnel-path" command cause device crash |
|
custom app not getting detected after attached removed and re-attached- app-visibility is disabled |
|
[17.5] Router crashed when sending traffic through non-SDWAN interface with DIA NAT + debug enabled |
|
An IOS XE device might crash at DoubleExceptionVector |
|
SDWAN cedge : traffic simulation tool shows traffic blackhole |
|
Packets dropped due to firewall + data policy interop issue |
|
SCEP: CA server fails to rollover CA certificate with error: "Storage not accessible" |
|
vtcp frees rx buffer when packet with expected next sequence arrives with no payload; phones reset |
|
Cisco 4331 ISR are crashing frequently 17.4.1b |
|
Security container is dropping legitimate FIN,ACK Packets |
|
IOS-XE cpp ucode crash with fragmented packets |
|
Cisco 4461 ISR NIM-2GE-CU-SFP - Sub-interfaces not transmitting traffic |
|
Signature update failure - SSL-CERTIFICATE_VERIFY_FAILED |
Open Caveats - Cisco IOS XE Amsterdam 17.3.3
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
Cisco 4000 Series ISR LACP Configuration lost: channel-group X "mode active" gets removed on reload |
|
LTE interface is not getting IP address after upgrading teh router. |
|
Crash at the moment of calculating tcp header |
|
Netflow crash at fnf_ipv6_output_feature_final_internal with flow record on IPv6 IPsec tunnel. |
|
CP process crashed while I95 driver was adding an IPC response to the receive ring |
|
NETCONF ACL not working if ACL is referencing an object-group. |
|
Cisco 4331 ISR/K9 running 16.12.04 crashed with Segmentation fault(11), Process = Cellular CNM |
|
Clients using DHCP Server Port-Based Address Allocation not getting IP address. |
|
cpp-mcplo-ucode crashes on Cisco 4461 ISR |
|
ucode crash with firewall timer lock |
|
bgp-neighbor down when push banner configuration failure |
|
IOS-XE Memory Leak in SSS Manager |
|
Router crash observed when AppNav Cluster delete with service-insertion enabled on LAN interface |
|
Cisco 4400 ISR routing multicast packets out of order VASI-left in VRF RIB VASI-right in Global RIB |
|
fman_rp: qos_hqf [L:1.0, N:0x3485061e18 ] (0p, 0c) download to FP failed resulting in a crash. |
|
ISR Crash for CENT-MC-0 process |
|
IP PIM SPT-threshold infinity causes ICMP Echo Replies to not be generated for IP Multicast Requests |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.3
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
Mishandling of dsmpSession pointer causes a crash |
|
Static routes pointing to interface tunnel not valid after tunnel's source interface flaps. |
|
IOSd Crash due to Segmentation fault at SISF Main Thread |
|
Cisco 4461 ISR: Control Connections over sub-interface are down after upgrade, TX Channel create failure |
|
Crash in sre_dp_traverse_dfa_legacy as SIP invite messages crosses a GRE Tunnel |
|
Cloud Express probes fails when two default rules are present |
|
Traceback: IP SLA triggers INJECT_HDR_LENGTH_ER and INJECT_FEATURE_ESCAPE log message |
|
17.4 : Dataplane Crash due to driver cpp_drv_i95_read_cb observed on Cisco 4461 ISR with traffic |
|
Crash seen in isis_sr_uloop_lspdb_dump with 'debug isis microloop' enabled |
|
BGP: advertised community list is malformed due to GSHUT community |
|
Cellular interface down/up frequently occurs with DoCoMo MVNO sim |
|
No responder-bytes from cEdge when UTD is enabled |
|
Router may crash when using Stateful NAT64 |
|
GETVPN: All GM will crash when Primary KS recovers its COOP role after network outage |
|
Moving PC from network causes static DHCP binding to be removed from the device. |
|
Cisco 4000 Series ISR SER parity error checks continuing till router crashes |
|
"platform ipsec reassemble transit" tail-drops unencrypted IPv4 Fragments with specific payload |
|
DMVPN with ipv6 link-local address do not register to HUB |
|
Router might crash after apply a class-map in input direction with bandwidth percentage |
|
NAT64 ALG: Router crashes on nat64_process_token |
|
Passive FTP doesn't work with NAT |
|
Crash in TCL Bytecode When Running RA Trace in Guestshell Python |
|
ISR router running 16.9.6 crashes authenticating crypto certificate |
|
Device Template failing to attach after changing few device variables |
|
Smart license registration through explicit mode proxy server |
|
[EVPN RT2-RT5] After few host moves RT2-RT5 re-origination happens even when there is no Remote RT2 |
|
MACSEC MKA stops forwarding data after every 3rd rekey |
|
Crash seen on Fugazi due to %CPPHA-3-FAILURE: R0/0: cpp_ha: CPP 0 failure Stuck Thread(s) |
|
ip-acl errors of correcting the logic of sequence id when there is an error with msg creation |
|
pktlog functionality is broken |
|
EVPN Type-2 IP/MAC route is created for not-connected SVI |
|
Unexpected reload in NHRP when access to an invalid memory region |
|
APPNAV CFT Crashes |
|
cEdge crashes due to a large packet at vesen_ipsec_v4_input_get_vctrl_data |
|
Pseudowire interface may be unexpectedly removed from VFI on unrelated configuration change |
|
OMP-Agent Routes in EIGRP changes AD to 252 on non-SDWAN devices |
|
CPP ucode crash with fw_base_flow_create |
|
SSH with Certificate authentication doesn't work after upgrade to 17.3.1 |
|
HSL Export over VASI Interface causes Netflow v9 Template Flooding |
|
unable to transfer 1500 byte IP packet when using BRI bundled Multilink |
|
RP went down due to __be_iosd_rec_malloc_free_before |
|
[SIT]: BFD sessions not established between Edges, with UTD enabled |
|
Dynamic Nat pool "ip aliases" are not created on the device |
|
LMR Unable to hear first seconds of audio |
|
Duplicate entries seen in MAC filter table. |
|
FlexVPN reactivate primary peer feature does not work with secondary peer tracking |
|
SDWAN ZBFW CPU punted traffic mishandling -- Out2In packet looped |
|
OpenSSL vulnerability (CVE-2020-1971) evaluation for IOS-XE |
|
Router may not send PIM Register message if RP is reachabile over TE tunnel |
|
Device is crashing after Device Access Policy is attached |
|
DDNS feature triggers crash on 16.X/17.X releases due to memory corruption |
|
Crash wile configuring l2vpn evpn instance for VXLAN |
|
Decouple mac aging from ARP aging on vlans not using the centralized gw feature |
|
BGP IPv6 link-local session doesn't come up |
|
Not able to create VFI instances |
|
Memory Lock and system crashed while clearing ip access-list stats. |
|
ISR crashes when ZBFW ALG inspects tunneled packet |
|
ISIS crash in isis_sr_tilfa_compute_protection |
|
Control plane hitting EID prefix entry limit for MAC after upgrade |
Open Caveats - Cisco IOS XE Amsterdam 17.3.2
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
PMAN-3-PROCFAIL: Chassis 1 R0/0: pman: R0/0: The process keyman has failed (rc 139). |
|
RM crash at __be_address_cmp __be_avl_get_next while doing shut/no shut or BR. |
|
BR crash at __be_strlen __be_fman_rtmap_create_route_map_msg. |
|
Router may crash under ZBF configuration. |
|
Crash during BGP VPN route import. |
|
Router may crash when using Stateful NAT64. |
|
SSS crashed the router at the moment of freeing AAA request. |
|
Pre-mature session deletion leading to churn and lower TPS at scale. |
|
Route not getting installed, need to remove and reattach the template. |
|
Cisco ISR router running 16.9.6 crashes authenticating crypto certificate. |
|
Device Template failing to attach after changing few device variables. |
|
Cisco 4000 ISRs fails to install new IPSec SAs. |
|
MACSEC MKA stops forwarding data after every 3rd rekey. |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.2
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
CME: Toll fraud app not automatically trusting traffic from phones. |
|
DNA - LAN Automation doe not configure link between Peer Device and PnP Agent due CDP limitation. |
|
Cube might crash when sending a SIP message over TLS. |
|
TCP traceroute - response ICMP TTL exceeded packet dropped by ZBFW with NAT enabled. |
|
Secure SIP trunk between SIP-GW/CUBE and CUCM with multiple nodes not coming in to service. |
|
DHCPD Receive process crash. |
|
Crash when IPSEC SA installation fails @ imgr_ipsec_sa_n2_install_done. |
|
Crashes when trying to bring-up / bring-down IPsec crypto session for OSPFv3. |
|
Unrecoverable Error with PVDM in 0/4 and Thule+dreamliner in 1/0 on Cisco 4300 ISR |
|
Incorrect Total number of translations on show ip nat translations. |
|
Punt fragment crash when receive EoGRE packets which have many fragments. |
|
Smart licensing PID and SN logs filling up the IOSRP tracelogs. |
|
Dialer interface counter does not correlate to the counter of interfaces bounded to. |
|
Cisco 4000 Series routers CPP ucode Crash due IPv4 Fragmented packets. |
|
KPML dialing fails after CSCvq20936 commit. |
|
STUN packet breaks MOH RTP packet flow. |
|
CUBE/LGW: STUN Indication packets generated constantly for call forking flows. |
|
QFP ucode crash with media monitor. |
|
Router crashes due to Segmentation Fault when ccb gives a NULL Pointer. |
|
Crash due to NBAR classification. |
|
GETVPN gikev2 Secondary KS does not push new policy after merging split condition. |
|
Router may crash unexpectedly with Segmentation fault(11), Process = DSMP. |
|
IPSEC install failed IPSEC_PAL_SA shows "unexpected number of parents. |
|
IOS PKI: CRL retrieval does not use HTTP Content-Length. |
|
ESP ucode crashed when running NAT with bpa (CGN). |
|
Observed Traceback with SRTP-RTP call after hold/resume. |
|
MGCP Calls with SRTP fail to connect with Cause Value=47 due to T.38 calls. |
|
While signalling forking the CUBE is not Sending Re-INVITE for T.38 with the Authorized header. |
|
GetVPN in Cisco 4461ISR: Getvpn traffic is failing with Transport mode with all the versions. |
|
CME-Cisco 4000 Series ISR: BLF working Inconsistently on IOS XE 16.09.03. |
|
CUBE generates 400 Bad Request when INVITE contains a large SDP and sip profiles are in use. |
|
Cisco 4000 Series ISRs: clear counters command may cause router to crash. |
|
IOS XE - ucode crash in ZBF during flow creation for TCP subflows/. |
|
CUBE is updating the resolved IP only after the REGISTER expires. |
|
IOS-XE crash after doing a SCEP enrollment. |
|
Cisco 4000 Series ISRs crash during updating the OpenDNS bypass whitelist |
|
Login authentication VTY_authen" is missing on "line vty 0 4" only. |
|
IWAN High CPU and Memory |
|
IWAN crash related to DCA channel. |
|
Router crashed when attempting to remove a nonexistent trustpoint from dspfarm profile. |
|
Spoke-to-spoke PLR packets should not change the interface PLR status. |
|
BGP Neighbors stuck on device. |
|
Flow monitor is removed from interface configuration on reload. |
|
Physical policy cannot be clean up with QoS policy in suspended mode on PPPoE dialer. |
|
Ruter see http wsma request as coming from 192.168.1.5. |
|
Call Rerouting functionality not working on 16.6/16.12/17.1 IOS-XE trains. |
|
Segmentation fault observed in BGP -"UNIX-EXT-SIGNAL: Segmentation fault(11), Process = BGP Scanner". |
|
Evaluation of CVE-2020-11868 for IOS. |
|
Punt-Keepalive crash with lsmpi_lo_drv and container app traffic. |
|
Crash due to a segmentation fault in the "IPsec background proc" process. |
|
Crash on configuring a highest key identifier for OSPF authentication under an interface. |
|
L2RIB thread crashed after removing global vrf definition for evpn. |
|
Router Crashes when advertised-routes command executed for neighbours. |
|
Random MPLS-TE tunnels with explicit-path stay down after egress interface is bounced. |
|
IOS-XE: IPv6 OSPF authentication ipsec - adjacency fails. |
|
Netconf deleting wrong IKEv2 parameters. |
|
Cisco 4000 Sereis ISR with SM-X-ES3 module: Memory leak in iomd. |
|
BMP BGP server can lead to CPUHOG and crashes |
|
Removing and Adding Bulk ACL leads to Tracebacks and Error-Objects. |
|
IOS crash at l2rib_server_ios_obj_notification. |
|
Crash due to a NULL pointer while bringing down PPPoE sessions. |
|
Cisco 4351 ISR:Crash seen with ZBFW. Reboot reason:Critical process qfp_ucode_utah fault on fp_0_0 (rc=139). |
|
[EVPN RT2-RT5] Routing Loop due to CGW re-originating the Type 2 MAC+IP with MAC+IP VRF details |
|
BGP crash in bgp_show_network_detail, bgp_imp_find_imported_path_topo. |
|
EVPN incorrect duplicate v4/v6 default routes, crash eventually. |
|
BGP crash during IOL testbed launch. |
|
Memory leak upon ssh/scp connections to a router. |
Open Caveats - Cisco IOS XE Amsterdam 17.3.1
All open caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
Cisoc 4461 ISR: Control Connections over sub-interface are down after upgrade, TX Channel create failure. |
|
Memory leak observed for FTM process leading to a device crash eventually. |
|
Netconf deleting wrong IKEv2 parameters. |
|
FlexVPN IKEv2 Tunnel route removed after establishing new IKEv2 SA to another peer. |
|
AnyConnect authentication fails when password contains "&" character. |
Resolved Caveats - Cisco IOS XE Amsterdam 17.3.1
All resolved caveats for this release are available in the Cisco Bug Search Tool.
Caveat ID Number |
Description |
---|---|
Router crashes after adding macsec reply-protection command on an interface. |
|
AnyConnect fails to reconnect when original session expires. |
|
Show crypto PKI server shows wrong expire certificate date. |
|
IOS PKI: P12 not generated on IOS Sub CA at rollover certificate generation. |
|
Cisco 4000 Series ISRs: %BOOT-3-BOOT_SRC: R0/0: No space on boot /dev/bootflash5 for packages, using bootflash!. |
|
Cisco 4000 Series ISRs crash when rtp-nte DTMF packet arrives at MTP + BDI. |
|
Cisco 4000 Series ISR crash in cpp_cp_svr due to watchdog timeout. |
|
Packet drops in XE-SDWAN because of IN_CD_COPROC_ANTI_REPLAY_FAIL" errors. |
|
PKI CLI - no warning that rsakeypair name starting from 0 (zero) is not working for cert regenerate. |
|
Interface does down when "l2vpn xconnect" command is removed. |
|
Router reloads due to crypto pki crl request <trustpoint-name> during get a fresh copy of CRL. |
|
Crash upon delete of virtual-access when virtual-template has "no tunnel protection ipsec initiate". |
|
TBAR is not disabled in GM when it is disabled in KS. |
|
Duplicate ipv6 address while connecting to remote client. |
|
GETVPN: KS 16.12.x - COOP switchover causes GMs to immediately use new TEK rekey. |
|
IPsec tunnel is getting established for a backup NHS DMVPN hub. |
|
Memory leak in SCCP TLS Client on unexpected deregister event. |
|
FlexVPN IKEv2 Tunnel route removed after establishing new IKEv2 SA to another peer. |
|
Enabling guestshell gives "float division by zero". |
|
CXP Probe DNS packets are not exiting via correct source interface. |
|
NAT doesnt translate SIP headers orignial source for return traffic on IOS XE 16.9.3 and 16.9.4. |