Step 1 |
config
RP/0/RSP0/CPU0:router# config
|
Enters global configuration mode.
|
Step 2 |
ssrp
profile
profile-name
RP/0/RSP0/CPU0:router(config)# ssrp profile Profile_1
|
Configures the Session State Redundancy
Protocol (SSRP) profile and enters the SSRP configuration mode.
|
Step 3 |
peer ipv4
address
A.B.C.D
RP/0/RSP0/CPU0:router(config)# peer ipv4 address 10.10.10.10
|
Configures the IPv4 address for a Session
State Redundancy Protocol (SSRP) peer.
|
Step 4 |
exit
RP/0/RSP0/CPU0:router(config-aps)# exit
|
Exits to the previous mode.
|
Step 5 |
ssrp
location
node_id
RP/0/RSP0/CPU0:router(config)# ssrp location 0/1/CPU0
|
Specifies the node on which to create a
Session State Redundancy Protocol (SSRP) group and enters the SSRP node
configuration mode
|
Step 6 |
group
group-id
profile
profile_name
RP/0/RSP0/CPU0:router(config-ssrp)# group 1 profile Profile_1
|
Creates a Session State Redundancy Protocol
(SSRP) group and associates it with a profile.
|
Step 7 |
group
group-id
profile
profile_name
RP/0/RSP0/CPU0:router(config-ssrp-node)# group 2 profile Profile_2
|
Creates a second Session State Redundancy
Protocol (SSRP) group and associates it with a profile.
|
Step 8 |
exit
RP/0/RSP0/CPU0:router(config-ssrp-node)# exit
|
Exits to the previous mode.
|
Step 9 |
interface
serial
interface-path-id[.subinterface]
RP/0/RSP0/CPU0:router(config)# interface serial 0/1/0/0/1/1:0
|
Physical interface or virtual interface.
For more information about the syntax for
the router, use the question mark (? ) online help function.
|
Step 10 |
ssrp
group
group-number
id
id-number
ppp
RP/0/RSP0/CPU0:router(config-if)# ssrp group 1 id 1 ppp
|
Attaches an SSRP group on the interface.
|
Step 11 |
encapsulation ppp
RP/0/RSP0/CPU0:router(config-if)# encapsulation ppp
|
Enables encapsulation for communication with
routers using the Point-to-Point Protocol (PPP).
|
Step 12 |
multilink
RP/0/RSP0/CPU0:router(config-if)# multilink
|
Enters the multilink interface configuration
mode.
|
Step 13 |
group
group-id
RP/0/RSP0/CPU0:router(config-if)# group 1
|
Attaches a Session State Redundancy Protocol
(SSRP) group to this interface.
|
Step 14 |
exit
RP/0/RSP0/CPU0:router(config)# exit
|
Exits to the previous mode.
|
Step 15 |
keepalive
disable
RP/0/RSP0/CPU0:router(config)# keepalive disable
|
Disables the keepalive timer for this
interface.
|
Step 16 |
exit
RP/0/RSP0/CPU0:router(config-if)# exit
|
Exits to the previous mode.
|
Step 17 |
interface
serial
interface-path-id[.subinterface]
RP/0/RSP0/CPU0:router(config)# interface serial 0/1/0/0/1/2:0
|
Physical interface or virtual interface.
For more information about the syntax for
the router, use the question mark (? ) online help function.
|
Step 18 |
ssrp
group
group-number
id
id-number
ppp
RP/0/RSP0/CPU0:router(config-if)# ssrp group 1 id 2 ppp
|
Attaches an SSRP group on the interface.
|
Step 19 |
encapsulation ppp
RP/0/RSP0/CPU0:router(config-if)# encapsulation ppp
|
Enables encapsulation for communication with
routers using the Point-to-Point Protocol (PPP).
|
Step 20 |
multilink
RP/0/RSP0/CPU0:router(config-if)# multilink
|
Enters the multilink interface configuration
mode.
|
Step 21 |
group
group-id
RP/0/RSP0/CPU0:router(config-if)# group 1
|
Attaches a Session State Redundancy Protocol
(SSRP) group to this interface.
|
Step 22 |
exit
RP/0/RSP0/CPU0:router(config-if)# exit
|
Exits to the previous mode.
|
Step 23 |
keepalive
disable
RP/0/RSP0/CPU0:router(config-if)# keepalive disable
|
Disables the keepalive timer for this
interface.
|
Step 24 |
exit
RP/0/RSP0/CPU0:router(config-if)# exit
|
Exits to the previous mode.
|
Step 25 |
interface
multilink
interface-path-id
RP/0/RSP0/CPU0:router(config)# interface Multilink 0/1/0/0/1
|
Physical interface or virtual interface.
For more information about the syntax for
the router, use the question mark (? ) online help function.
|
Step 26 |
ipv4
address
ipv4-address
mask
RP/0/RSP0/CPU0:router(config-if )# ipv4 address 10.10.10.10 255.255.255.0
|
Sets the primary IPv4 address and subnet
mask for an interface.
|
Step 27 |
ssrp
group
group-number
id
id-number
ppp
RP/0/RSP0/CPU0:router(config-if)# ssrp group 1 id 3 ppp
|
Attaches an SSRP group on the interface.
|
Step 28 |
encapsulation ppp
RP/0/RSP0/CPU0:router(config-if)# encapsulation ppp
|
Enables encapsulation for communication with
routers using the Point-to-Point Protocol (PPP).
|
Step 29 |
shutdown
RP/0/RSP0/CPU0:router(config-if)# shutdown
|
Brings the interface administratively down
for configuration.
|
Step 30 |
keepalive
disable
RP/0/RSP0/CPU0:router(config-if)# keepalive disable
|
Disables the keepalive timer for this
interface.
|
Step 31 |
exit
RP/0/RSP0/CPU0:router(config-if)# exit
|
Exits to the previous mode.
|
Step 32 |
controller
MgmtMultilink
interface-path-id
RP/0/RSP0/CPU0:router(config)# controller MgmtMultilink 0/1/0/0
|
Configure a controller for a generic
multilink bundle and enters MgmtMultilink configuration mode.
|
Step 33 |
bundle
bundleID
RP/0/RSP0/CPU0:router(config-mgmtmultilink)# bundle 1
|
Creates a multilink interface bundle.
|
Step 34 |
bundle
bundleID
RP/0/RSP0/CPU0:router(config-mgmtmultilink)# bundle 2
|
Creates a multilink interface bundle.
|
Step 35 |
commit
RP/0/RSP0/CPU0:router(config-mgmtmultilink)# commit
|
Saves the current configuration.
|