-
Short Guard Interval Supported — This field is available only if the selected radio mode includes 802.11n. The guard interval is the dead time, in nanoseconds,
between the OFDM symbols. The guard interval prevents Inter-Symbol and Inter-Carrier Interference (ISI, ICI). The 802.11n
mode allows for a reduction in this guard interval from the a and g definition of 800 nanoseconds to 400 nanoseconds. Reducing
the guard interval can yield a 10 percent improvement in data throughput. The client with which the WAP device is communicating
must also support the short guard interval.
Choose one of these options:
-
Yes — The WAP device transmits data using a 400-nanosecond guard interval when communicating with clients that also support the
short guard interval. This is the default selection.
-
No — The WAP device transmits data using an 800-nanosecond guard interval.
-
Protection — The protection feature contains rules to guarantee that 802.11 transmissions do not cause interference with legacy stations
or applications. By default, protection is enabled (Auto). With protection enabled, protection is invoked if the legacy devices
are within the range of the WAP device.
You can disable the protection (Off); however, the legacy clients or the WAP devices within the range can be affected by the
802.11n transmissions. Protection is also available when the mode is 802.11b/g. When protection is enabled in this mode, it
protects the 802.11b clients and the WAP devices from the 802.11g transmissions.
Note
|
This setting does not affect the ability of the client to associate with the WAP device.
|
-
Beacon Interval — The interval between the transmission of beacon frames. The WAP device transmits these frames at regular intervals to announce
the existence of the wireless network. The default behavior is to send a beacon frame once every 100 milliseconds (or 10 per
second). Enter an integer from 20 to 2000 milliseconds. The default is 100 milliseconds.
-
DTIM Period — The Delivery Traffic Information Map (DTIM) period. Enter an integer from 1 to 255 beacons. The default is 2 beacons.
The DTIM message is an element included in some beacon frames. It indicates which client stations, currently sleeping in low-power
mode, have data buffered on the WAP device awaiting pickup.
The DTIM period indicates how often the clients served by this WAP device should check for buffered data awaiting pickup.
The measurement is in beacons. For example, if you set it to 1, the clients check for buffered data on the WAP device at every
beacon. If you set it to 10, the clients check on every 10th beacon.
-
Fragmentation Threshold — The frame size threshold is in bytes. The valid integer must be even and in the range of 256 to 2346. The default is 2346.
The fragmentation threshold is a way of limiting the size of packets (frames) transmitted over the network. If a packet exceeds
the fragmentation threshold set, the fragmentation is activated and the packet is sent as multiple 802.11 frames.
If the packet being transmitted is equal to or less than the threshold, the fragmentation is not used. Setting the threshold
to the largest value (2,346 bytes, which is the default) effectively disables the fragmentation.
By default, the fragmentation is off. We recommend not using fragmentation unless you suspect the radio interference. The
additional headers applied to each fragment increase the overhead on the network and can greatly reduce the throughput.
-
RTS Threshold — The Request to Send (RTS) Threshold value. The valid integer range must be from 0 to 65535. The default is 65535 octets.
The RTS threshold indicates the number of octets in an MPDU, below which an RTS/CTS handshake is not performed.
Changing the RTS threshold can help control the traffic flow through the WAP device. If you specify a low threshold value,
the RTS packets are sent more frequently, which consumes more bandwidth and reduces the throughput of the packet. However,
sending more RTS packets can help the network recover from interference or collisions that might occur on a busy network,
or on a network experiencing electromagnetic interference.
-
Max Associated Clients — The maximum number of stations allowed to access the WAP device at any one time. You can enter an integer between 0 and
100. The default is 100 stations.
-
Transmit Power — A percentage value for the transmit power level of the WAP device.
The default value of Full - 100 % can be more cost-efficient than a lower percentage because it gives the WAP device a maximum
broadcast range and reduces the number of access points needed.
To increase the capacity of the network, place the WAP devices closer together and reduce the value of the transmit power.
This setting helps reduce overlap and interference among the access points. A lower transmit power setting can also keep your
network more secure because the weaker wireless signals are less likely to propagate outside of the physical location of your
network.
Some channel ranges and country code combinations have relatively low maximum transmit power. When attempting to set the transmit
power to the lower ranges (for example, Medium - 25 percent or Low -12 percent), the expected drop in power may not occur,
because certain power amplifiers have minimum transmit power requirements.
-
Frame-burst Support — Generally enabling the Frame-burst support improves the radio performance in the downstream direction.
-
Airtime Fairness Mode — The airtime fairness (ATF) feature was implemented to address the issue of slower-data transfers throttling the higher-speed
ones.
-
Maximum Utilization Threshold —Enter the percentage of network bandwidth utilization allowed on the radio before the WAP device stops accepting new client
associations. The valid integer range is from 0 to 100 percent. The default is 0 percent. When set to 0, all new associations
are allowed regardless of the utilization rate.
-
Fixed Multicast Rate — The transmission rate in Mbps for broadcast and multicast packets. This setting can be useful in an environment where the
wireless multicast video streaming occurs, provided the wireless clients are capable of handling the configured rate.
When Auto is selected, the WAP device chooses the best rate for the associated clients. The range of valid values is determined by
the configured radio mode.
-
Legacy Rate Sets — Rates are expressed in megabits per second.
The Supported Rate Sets indicate the rates that the WAP device supports. You can check multiple rates. The WAP device automatically
chooses the most efficient rate based on the factors such as error rates and the distance of the client stations from the
WAP device.
The Basic Rate Sets indicate the rates that the WAP device advertises to the network for the purposes of setting up communication
with other access points and client stations on the network. It is generally more efficient to have a WAP device broadcast
a subset of its supported rate sets.
-
Broadcast/Multicast Rate Limiting — Multicast and broadcast rate limiting can improve overall network performance by limiting the number of packets transmitted
across the network.
By default, this feature is disabled. Until you enable this feature, these fields are disabled:
-
Rate Limit — The rate limit for multicast and broadcast traffic which should be greater than 1, but less than 50 packets per second.
Any traffic that falls below this rate limit will always conform and be transmitted to the appropriate destination. The default
and maximum rate limit setting is 50 packets per second.
-
Rate Limit Burst — An amount of traffic, measured in bytes, which is allowed to pass as a temporary burst even if it is above the defined maximum
rate. The default and maximum rate limit burst setting is 75 packets per second.
-
VHT Features — The purpose of this feature is to enable or disable the Broadcom specific extensions in VHT for Broadcom-to-Broadcom links.
The VHT feature enables support for 256QAM VHT rates not specified by the 802.11 ac Draft. The rates are all VHT LDPC mode,
MCS 9 Nss 1 20Mhz, MCS 9 Nss 2 20Mhz, MCS 6 Nss 3 80Mhz. The VHT feature is supported for 802.11 ac PHY.