First Published: August 17, 2018

Last Updated: February 4, 2020

About the Release Notes

This release notes document describes what is new or changed in this release, instructions to upgrade to this release, and open and resolved caveats for this release. Unless otherwise noted, in this document, Cisco Wireless Controllers are referred to as controllers, and Cisco lightweight access points are referred to as access points or APs.

Content Hub

Explore the Content Hub, the all-new product documentation portal in which you can use faceted search to locate content that is most relevant to you, create customized PDFs for ready reference, benefit from context-based recommendations, and much more.

Get started with the Content Hub at https://content.cisco.com/ to craft a personalized documentation experience.

Do provide feedback about your experience with the Content Hub.

Supported Cisco Wireless Controller Platforms

The following Cisco Wireless Controller platforms are supported in this release:

  • Cisco 3504 Wireless Controller

  • Cisco 5520 Wireless Controller

  • Cisco 8540 Wireless Controller

  • Cisco Virtual Wireless Controller (vWLC) on the following platforms:

    • VMware vSphere Hypervisor (ESXi) Version 5.x and 6.x

    • Hyper-V on Microsoft Servers 2012 and later versions (Support introduced in Release 8.4)

    • Kernel-based virtual machine (KVM) (Support introduced in Release 8.1. After KVM is deployed, we recommend that you do not downgrade to a Cisco Wireless release that is earlier than Release 8.1.)

  • Cisco Wireless Controllers for High Availability for Cisco 3504 WLC, Cisco 5520 WLC, and Cisco 8540 WLC.

  • Cisco Mobility Express Solution

Supported Cisco Access Point Platforms

The following Cisco AP platforms are supported in this release:

  • Cisco Aironet 700 Series Access Points

  • Cisco Aironet 700W Series Access Points

  • Cisco AP803 Integrated Access Point

  • Integrated Access Point on Cisco 1100, 1101, and 1109 Integrated Services Routers

  • Cisco Aironet 1700 Series Access Points

  • Cisco Aironet 1800 Series Access Points

  • Cisco Aironet 1810 Series OfficeExtend Access Points

  • Cisco Aironet 1810W Series Access Points

  • Cisco Aironet 1815 Series Access Points

  • Cisco Aironet 1830 Series Access Points

  • Cisco Aironet 1850 Series Access Points

  • Cisco Aironet 2700 Series Access Points

  • Cisco Aironet 2800 Series Access Points

  • Cisco Aironet 3700 Series Access Points

  • Cisco Aironet 3800 Series Access Points

  • Cisco Aironet 4800 Series Access Points

  • Cisco ASA 5506W-AP702

  • Cisco Aironet 1530 Series Access Points

  • Cisco Aironet 1540 Series Access Points

  • Cisco Aironet 1560 Series Access Points

  • Cisco Aironet 1570 Series Access Points

  • Cisco Industrial Wireless 3700 Series Access Points


Note

For information about Cisco Wireless software releases that support specific Cisco access point modules, see the "Software Release Support for Specific Access Point Modules" section in the Cisco Wireless Solutions Software Compatibility Matrix document.

What's New in Release 8.8.100.0

This section provides a brief introduction to the new features and enhancements that are introduced in this release.


Note

For complete listing of all the documentation published for Cisco Wireless Release 8.8, see the Documentation Roadmap:

https://www.cisco.com/c/en/us/td/docs/wireless/doc-roadmap/doc-roadmap-release-88.html

Software-Defined Access Features

The following software-defined access (SDA) features are supported in this release:

  • IPv6 Client Support in SDA: The following IPv6 features are supported in this release:

    • IPv6 client support: IPv6 and dual-stack wireless clients can be brought up and serviced by controllers in an SDA framework. The clients can be of Static, Stateful DHCPv6, or SLACC types.

    • IPv6 client mobility: IPv6 clients can move across APs within an SDA network and preserve their IPv6 connectivity when roaming. 802.11r Fast Roaming is supported if the client supports it.

    • IPv6 DNS-based ACLs: In Release 8.7, this feature was introduced with support for only IPv4. In Release 8.8, this feature is enhanced such that FlexConnect IPv6 ACLs accept internet domain names in addition to IPv6 addresses in their rules. With DNS-based ACLs, clients that are in the preauthentication phase are allowed to connect to the configured URLs.

    • IPv6 client HA: In an HA environment, client states are preserved even if there are any controller failures. Also, the access node and intermediate node redundancy mechanisms that are configured in an SDA network strive to provide an additional layer of HA protection to clients.

  • Multicast-to-Unicast of IPv4 VideoStream in SDA: Multicast-to-unicast video traffic on APs operating in Local mode is supported in SDA.

    For more information about deploying VideoStream, see

    https://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112889-cuwns-vidstrm-guide-00.html.

  • Outdoor AP in SDA: SDA is supported in Cisco Aironet 1540 and 1560 APs operating in Local mode.

  • Cisco Wave 1 APs as Workgroup Bridges in SDA: Cisco Wave 1 APs operating as Workgroup Bridges (WGBs) is supported in SDA.


    Note

    Cisco Wave 2 APs as WGBs in SDA is in Early Field Trial state and not yet officially supported.

For more information about Software-Defined Access, see the following documentation:

One-to-One Mapping of WLAN with EoGRE VLAN

The EoGRE implementation for open WLANs is limited to 10 WLANs per VLAN per controller. This limitation can be overcome by having a one-to-one mapping between open WLANs and EoGRE VLANs.

A one-to-one mapping of WLAN with EoGRE VLAN can be achieved by overriding the EoGRE VLAN configuration within the WLAN. All the existing rules are still applicable; however, if you enable EoGRE VLAN override, the VLAN ID that you specify is overridden with EoGRE VLAN ID, which is configured in the tunnel profile that is mapped to the WLAN.

The order of precedence is as follows:

  1. If the AAA override option is enabled on the WLAN, then AAA values are applied.

  2. If the EoGRE VLAN configuration override option is enabled, then EoGRE VLAN configuration values are applied on the VLAN ID specified.

  3. Network Access Identifier (NAI) matched in the EoGRE profile rule.

You can track this enhancement in the CSCuy30302 caveat.

For more information, see

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/client_data_tunneling.html#eogre.

Identity PSK with Peer-to-Peer Blocking

The Identity PSK (IPSK) feature is enhanced to configure peer-to-peer (P2P) blocking or bridging. This enhancement is applicable in scenarios where clients or IoT devices with different or same PSKs on the same WLAN have to be prevented from communicating with each other. With this enhancement, it is possible to differentiate private PSK client traffic. This enhancement is supported only in Local mode.

For more information, see

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/wlan_security.html#peer-to-peer-blocking-using-psk-tag.

Lawful Interception of Traffic

This feature is implemented to meet the need for lawful interception of traffic for monitoring purposes.

APs create syslog-based records for the traffic and send these records to the controller. Traffic from both IPv4 and IPv6 protocols is captured. At defined intervals, the controller sends these syslog records to the syslog server.

For more information, see

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/lawful_interception_of_traffic.html.

Captive Portal Enhancement

It is possible to configure external redirect URL at the AP group level apart from the existing configuration options at the global and WLAN levels. This enhancement is to enable you to configure multiple splash pages for the same SSID.

If both WLAN and AP group configurations do not override the global configuration, then the global configuration is used.

If either WLAN or AP group configuration overrides the global configuration, then the specific redirect URL that is configured is used.

If both WLAN and AP group configurations override the global configuration, the AP group configuration is used because the AP group configuration takes precedence over the WLAN configuration.

For more information, see

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/configuring_ap_groups.html#captive_portal_for_ap_group.

Policy Enforcement and Monitoring Usage

This feature helps in providing continued data bandwidth to clients after the allocated high-speed data bandwidth has exhausted albeit at lower data rates. This dynamic policy override works on L2 and L3 client authentication.

AP sends the client bandwidth usage report to the controller at a set duration. The controller sends these reports to the accounting server at a set duration. When the client exhausts the data limit, the AAA server sends a change of authorization (CoA) request. The controller changes the policy parameters after receiving confirmation from the AAA server.

The policy change and data rate change occur without disconnecting the client.

This feature is supported in the following modes:

  • Central Switching; Local and Bridge mode

  • Local Switching; FlexConnect and Flex+Bridge mode

For more information, see

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/wlan_security.html#policy-enforcement-quota-mgmt.

Application Visibility and Control Enhancements

NBAR2 Protocol Pack Upgrade

Before Release 8.8, controllers supported NBAR engine version 23, and the default protocol pack version was 19.1. To support more applications on the controllers, especially Wi-Fi Calling, Zoom, and so on, Release 8.8 includes NBAR engine version 31 and protocol pack version 37 for controllers; for Cisco Wave 1 APs, the NBAR engine is version 23 and the protocol pack version is 14; for Cisco Wave 2 APs, the NBAR engine is version 35 and the protocol pack version is 33.


Note

Enabling AVC in FlexConnect mode in an environment wherein both Wave 1 and Wave 2 APs are present will break AVC policies.

Default DSCP Value for AVC Profile

Before Release 8.8 with AVC enabled, you could override DSCP values for only those application flows that were configured on an AVC profile. For the application flows that were not configured, no action was performed and DSCP was left intact. The maximum number of application rules that the AVC profile can contain is 32. For managed service, to control and rewrite DSCP values (example with DSCP 0) for all flows that are not presented on the AVC profile is not possible.

In Release 8.8, the new enhancement includes a new default-class rule that you can use to override the DSCP values for all application flows in which AVC rule is not configured. The goal of this enhancement is to protect the network for all flows with unwanted or controlled DSCP values.

This enhancement comes with the following restrictions:

  • Only the start of an application flow is captured.

  • Supported only for marking. Rate limit and drop are not supported.

  • Default DSCP works only if AVC is in enabled state.

  • An AVC profile can support up to 32 rule, including the default-class rule. If the default-rule is configured, you can configure up to 31 rules.

  • Multicast and broadcast flows are not supported.

  • IPv6 is not supported in AVC.

  • Cascading of rules is not supported, which means that for the same flow, it is not possible to have rate limiting and marking. Therefore, if rate limiting is performed for a flow, default marking is not performed on the flow.


Note

  • The default-class setting overwrites all DSCP values for all the application flows that are not configured when the profile is applied to a WLAN.

  • If you have an AVC profile with default-class setting and you downgrade from Release 8.8 to an earlier release, the default-class setting is still present in the controller, although the earlier releases do not support this setting.

Cisco Wave 2 AP Features

Support is added for the following features in Wave 2 APs in this release:

  • Flex+Mesh

  • CAPWAP IPv6

  • Auto-LAG in FlexConnect mode


    Note

    This feature is supported only in Cisco Aironet 2800, 3800, and 4800 Series APs.

  • USB port as a power source

    Cisco Aironet 2800 and 3800 Series APs have a USB port that can act as a source of power for some USB devices. The power can be up to 2.5W; if a USB device draws more than 2.5W of power, the USB port shuts down automatically. For more information, see

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/ap_power_and_lan_connections.html#info_ap_usb_port_as_power_source.

  • DHCP on root access points

    Internal DHCPv4 server is supported in root access points (RAPs) operating in Flex+Mesh mode. This feature is supported only in Cisco Aironet 1540 and 1560 APs.

    Network Address Translation (NAT) and Port Address Translation (PAT) in RAPs operating in Flex+Mesh mode is coupled with the internal DHCP server support. NAT/PAT on RAPs start when you start the DHCP server and stops when you stop the DHCP server.

Miscellaneous Enhancements

  • Disabling AP fallback to DHCP when configured for static IP addresses: Cisco APs can fall back from static IP mode to DHCP mode when they are not able to associate with a controller. While it is useful to get the APs to fall back to DHCP mode so that they continue to serve clients by getting a new IP address, the APs retain their new IP address until they are rebooted. In a network where the APs are assigned static IP addresses, the DHCP IP addresses prevent the APs from being monitored. To address this issue, you can choose to retain the static IP addresses for APs by disabling the fallback to the DHCP option.

    This enhancement is tracked in CSCua58662.

    For more information, see

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/managing_aps.html#retaining_static_ip_on_ap_cli.

  • ARP debugs: In Release 8.8, when ARP debugs are enabled along with debugging of clients, it is possible to filter and view ARP debugs for a specific client instead of listing all the ARP transactions.

    This enhancement is tracked in CSCun60412.

  • Logging of configuration history: You can view the logging buffer that is saved on the last reset or power cycle of the controller by entering this command:

    show logging config-history

    You can also retrieve the details of all the config commands that are executed in the current and up to two previous resets through a support bundle.

    This enhancement is tracked in CSCur14475.

    For more information, see

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/debugging_on_cisco_wireless_controllers.html#ID200

  • FlexConnect client exclusion list: You can view the FlexConnect clients in the exclusion list of an AP locally by entering this command on the Wave 2 AP console:

    show flexconnect client exclusion-list

    This enhancement is tracked in CSCux41096.

    For more information, see

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/wlan_security.html#config-client-exclusion-policies.

  • SFP type information: You can view the SFP type information on Cisco 5520 and 8540 controllers by entering this command:

    show port sfp-info

    This enhancement is tracked in CSCva88371.

  • Platform information in a debug session: In the controller CLI, at the start of a debug session, a message is displayed indicating the platform details for which the debug session is being started. This message contains the following information: timestamp, controller model, software release information, serial number of the controller model, and the hostname.

    This enhancement is tracked in CSCvf03977.

    For more information, see

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/debugging_on_cisco_wireless_controllers.html#ID200

  • Extension of | include filtering: Before this release, some show commands on the Wave 2 AP console allowed filtering using the | include option. In Release 8.8, this option is extended to all the show commands.

    This enhancement is tracked in CSCvg42570.

  • IPv6 in Flex+Mesh mode: IPv6 is supported in Flex+Mesh mode.

  • DHCP with NAT: DHCP is supported in APs with NAT (only IPv4).

  • Federal certification requirements: To meet federal certification requirements wherein, in a High Availability scenario, data between active and standby controllers must be encrypted. This requirement is achieved by doing IPsec encryption with certificates on the HA controllers.

Early Field Trial Features

The following features are in Early Field Trial state:


Note

These features are not yet officially supported and there will be no assistance from Cisco's Technical Assistance Center.

Software Release Types and Recommendations

Table 2. Release Types

Release Type

Description

Benefit

Maintenance Deployment (MD)

Software releases that provide bug-fix support and ongoing software maintenance. These releases are categorized as Maintenance Deployment (MD).

These releases are long-living releases with ongoing software maintenance.

Provides you with a software release that offers stability and long support duration with periodic maintenance releases (MRs).

Early Deployment (ED)

Software releases that provide new features and new hardware platform support in addition to bug fixes. These releases are categorized as Early Deployment (ED).

These releases are short-lived releases.

Allows you to deploy the latest features and new hardware platforms or modules.

For detailed release recommendations, see the Guidelines for Cisco Wireless Software Release Migration Bulletin at:

http://www.cisco.com/c/en/us/products/collateral/wireless/8500-series-wireless-controllers/bulletin-c25-730741.html.

Table 3. Upgrade Path to Cisco Wireless Release 8.8.x

Current Software Release

Upgrade Path to Release 8.8.x

8.2.x

You must upgrade to an 8.5.x release and then upgrade to Release 8.8.x.

8.3.x

You must upgrade to an 8.5.x release and then upgrade to Release 8.8.x.

8.4.x

You must upgrade to an 8.5.x release and then upgrade to Release 8.8.x.

8.5.x

You can upgrade directly to Release 8.8.x.

8.6.x

You can upgrade directly to Release 8.8.x.

8.7.x

You can upgrade directly to Release 8.8.x.

Upgrading Cisco Wireless Release

This section describes the guidelines and limitations that you must be aware of when you are upgrading the Cisco Wireless release and the procedure to upgrade.


Caution

Before you upgrade to this release, we recommend that you go through the following documents to understand various issues related to Cisco Wave 1 AP flash and the solution to address them:

Guidelines and Limitations

  • Legacy clients that require RC4 or 3DES encryption types are not supported in Local EAP authentication.

  • If you downgrade from Release 8.8.x to Release 8.7, FlexConnect IPv6 ACLs are shown to be in their FlexConnect group.

  • If you have an AVC profile with default-class setting and you downgrade from Release 8.8.x to an earlier release, the default-class setting is still present in the controller, although the earlier releases do not support this setting.

  • If you want to downgrade from Release 8.8.x to Release 8.6.101.0 and if you have Wave 2 APs in Flex+Bridge mode, ensure that these APs are changed to Bridge mode before you perform the downgrade; else, the APs will have incorrect configuration after the downgrade process.

  • If you are upgrading from Release 8.0.140.0 or 8.0.15x.0 to a later release and also have the multiple country code feature configured, the feature configuration is corrupted after the upgrade. For more information, see CSCve41740.

  • After downloading the new software to the Cisco APs, it is possible that a Cisco AP may get stuck in an upgrading image state. In such a scenario, it might be necessary to forcefully reboot the controller to download a new controller software image or to reboot the controller after the download of the new controller software image. You can forcefully reboot the controller by entering the reset system forced command.

  • It is not possible to download some of the older configurations from the controller because of the Multicast and IP address validations. See the "Restrictions on Configuring Multicast Mode" section in the Cisco Wireless Controller Configuration Guide for detailed information about platform support for global multicast and multicast mode.

  • When a client sends an HTTP request, the controller intercepts it for redirection to the login page. If the HTTP GET request that is intercepted by the controller is longer than 2000 bytes, the controller drops the packet. Track the Caveat ID CSCuy81133 for a possible enhancement to address this restriction.

  • When downgrading from one release to an earlier release, you might lose the configuration from your current release. The workaround is to reload the previous controller configuration files that are saved in the backup server, or to reconfigure the controller.

  • When you upgrade controller to an intermediate release, wait until all the APs that are associated with the controller are upgraded to the intermediate release before you install the latest controller software. In large networks, it can take some time to download the software on each AP.

  • You can upgrade to a new release of the controller software or downgrade to an earlier release even if FIPS is enabled.

  • When you upgrade to the latest software release, the software on the APs associated with the controller is also automatically upgraded. When an AP is loading software, each of its LEDs blinks in succession.

  • Controllers support standard SNMP MIB files. MIBs can be downloaded from the software download page on Cisco.com.

  • The controller software that is factory-installed on your controller and is automatically downloaded to the APs after a release upgrade and whenever an AP joins a controller. We recommend that you install the latest software version available for maximum operational benefit.

  • Ensure that you have a TFTP, HTTP, FTP, or SFTP server available for the software upgrade. Follow these guidelines when setting up a server:

    • Ensure that your TFTP server supports files that are larger than the size of controller software image. Some TFTP servers that support files of this size are tftpd32 and the TFTP server within Cisco Prime Infrastructure. If you attempt to download the controller software image and your TFTP server does not support files of this size, the following error message appears:

      TFTP failure while storing in flash

    • If you are upgrading through the distribution system network port, the TFTP or FTP server can be on the same subnet or a different subnet because the distribution system port is routable.

  • The controller Bootloader stores a copy of the active primary image and the backup image. If the primary image becomes corrupted, you can use the Bootloader to boot with the backup image.

    With the backup image stored before rebooting, from the Boot Options menu, choose Option 2: Run Backup Image to boot from the backup image. Then, upgrade with a known working image and reboot controller.

  • You can control the addresses that are sent in the Control and Provisioning of Wireless Access Points (CAPWAP) discovery responses when NAT is enabled on the Management Interface, using the following command:

    config network ap-discovery nat-ip-only {enable | disable}

    The following are the details of the command:

    enable —Enables use of NAT IP only in a discovery response. This is the default. Use this command if all the APs are outside the NAT gateway.

    disable —Enables use of both NAT IP and non-NAT IP in a discovery response. Use this command if APs are on the inside and outside the NAT gateway, for example, Local Mode and OfficeExtend APs are on the same controller.


    Note

    To avoid stranding of APs, you must disable AP link latency (if enabled) before you use the disable option in the config network ap-discovery nat-ip-only command. To disable AP link latency, use the config ap link-latency disable all command.

  • Do not power down controller or any AP during the upgrade process. If you do this, the software image might get corrupted. Upgrading controller with a large number of APs can take as long as 30 minutes, depending on the size of your network. However, with the increased number of concurrent AP upgrades supported, the upgrade time should be significantly reduced. The APs must remain powered, and controller must not be reset during this time.

  • After you perform the following functions on controller, reboot it for the changes to take effect:

    • Enable or disable LAG.

    • Enable a feature that is dependent on certificates (such as HTTPS and web authentication).

    • Add a new license or modify an existing license .


      Note

      Reboot is not required if you are using Right-to-Use licenses.

    • Increase the priority of a license.

    • Enable HA.

    • Install the SSL certificate.

    • Configure the database size.

    • Install the vendor-device certificate.

    • Download the CA certificate.

    • Upload the configuration file.

    • Install the Web Authentication certificate.

    • Make changes to the management interface or the virtual interface.

  • From Release 8.3 or a later release, ensure that the configuration file that you back up does not contain the < or > special characters. If either of the special characters is present, the download of the backed up configuration file fails.

Upgrading Cisco Wireless Software (GUI)

Procedure

Step 1

Upload your controller configuration files to a server to back up the configuration files.

Note 

We highly recommend that you back up your controller configuration files prior to upgrading the controller software.

Step 2

Follow these steps to obtain controller software:

  1. Browse to the Software Download portal at: https://software.cisco.com/download/home.

  2. Search for the controller model.

  3. Click Wireless LAN Controller Software.

  4. The software releases are labeled as described here to help you determine which release to download. Click a controller software release number:

    • Early Deployment (ED)—These software releases provide new features and new hardware platform support as well as bug fixes.

    • Maintenance Deployment (MD)—These software releases provide bug fixes and ongoing software maintenance.

    • Deferred (DF)—These software releases have been deferred. We recommend that you migrate to an upgraded release.

  5. Click the filename <filename.aes>.

  6. Click Download.

  7. Read the Cisco End User Software License Agreement and click Agree.

  8. Save the file to your hard drive.

  9. Repeat steps a through h to download the remaining file.

Step 3

Copy the controller software file <filename.aes> to the default directory on your TFTP, FTP, or SFTP server.

Step 4

(Optional) Disable the controller 802.11 networks.

Note 

For busy networks, controllers on high utilization, and small controller platforms, we recommend that you disable the 802.11 networks as a precautionary measure.

Step 5

Choose Commands > Download File to open the Download File to Controller page.

Step 6

From the File Type drop-down list, choose Code.

Step 7

From the Transfer Mode drop-down list, choose TFTP, FTP, or SFTP.

Step 8

In the IP Address field, enter the IP address of the TFTP, FTP, or SFTP server.

Step 9

If you are using a TFTP server, the default value of 10 retries for the Maximum Retries field, and 6 seconds for the Timeout field should work correctly without any adjustment. However, you can change these values, if required. To do so, enter the maximum number of times the TFTP server attempts to download the software in the Maximum Retries field and the amount of time (in seconds) for which the TFTP server attempts to download the software, in the Timeout field.

Step 10

In the File Path field, enter the directory path of the software.

Step 11

In the File Name field, enter the name of the software file <filename.aes>.

Step 12

If you are using an FTP server, perform these steps:

  1. In the Server Login Username field, enter the username with which to log on to the FTP server.

  2. In the Server Login Password field, enter the password with which to log on to the FTP server.

  3. In the Server Port Number field, enter the port number on the FTP server through which the download occurs. The default value is 21.

Step 13

Click Download to download the software to the controller.

A message indicating the status of the download is displayed.

Note 

Ensure that you choose the File Type as Code for both the images.

Step 14

After the download is complete, click Reboot.

Step 15

If you are prompted to save your changes, click Save and Reboot.

Step 16

Click OK to confirm your decision to reboot the controller.

Step 17

If you have disabled the 802.11 networks, reenable them.
Step 18

(Optional) To verify that the controller software is installed on your controller, on the controller GUI, click Monitor and view the Software Version field under Controller Summary.

CIMC Utility Upgrade for 5520 and 8540 Controllers

The AIR-CT5520-K9 and AIR-CT8540-K9 controller models are based on Cisco UCS server C series, C220 and C240 M4 respectively. These controller models have CIMC utility that can edit or monitor low-level physical parts such as power, memory, disks, fan, temperature, and provide remote console access to the controllers.

We recommend that you upgrade the CIMC utility to Version 3.0(4d) that has been certified to be used with these controllers. Controllers that have older versions of CIMC installed are susceptible to rebooting without being able to access FlexFlash, with the result that the manufacturing certificates are unavailable, and thus SSH and HTTPS connections will fail, and access points will be unable to join. See: CSCvo33873.

The CIMC 3.0(4d) images are available at the following locations

Table 4. CIMC Utility Software Image Information

Controller

Link to Download the CIMC Utility Software Image

Cisco 5520 Wireless Controller

https://software.cisco.com/download/home/286281345/type/283850974/release/3.0%25284d%2529

Cisco 8540 Wireless Controller

https://software.cisco.com/download/home/286281356/type/283850974/release/3.0%25284d%2529

For information about upgrading the CIMC utility, see the "Updating the Firmware on Cisco UCS C-Series Servers" chapter in the Cisco Host Upgrade Utility 3.0 User Guide:

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/sw/lomug/2-0-x/3_0/b_huu_3_0_1/b_huu_2_0_13_chapter_011.html

Updating Firmware Using the Update All Option

This section mentions specific details when using CIMC utility with Cisco 5520 or 8540 controllers. For general information about the software and UCS chassis, see Release Notes for Cisco UCS C-Series Software, Release 3.0(4) at:

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/release/notes/b_UCS_C-Series_Release_Notes_3_0_4.html

Table 5. Open Caveats for Release 3.0(4d)

Caveat ID

Description

CSCvj80941

After upgrading CIMC to 3.04d, only after power reset, UCS-based controller is coming up.

CSCvj80915

Not able to logon to the CIMC GUI with the username and password that are configured from the controller.
Table 6. Resolved Caveats for Release 3.0(4d)

Caveat ID

Description

CSCvd86049

Symptom: The system will stop working or reboot during OS operation with PROCHOT, MEMHOT, and DMI Timeout-related events reported in the System Event Log (SEL).

Conditions: C220-M4 or C240-M4

Workaround: No workaround is available.

This bug fix changes the default BIOS option for ASPM (Active State Power Management) from 'L1 only' to 'Disabled', and the ASPM setting can no longer be modified. This change was made to help increase system stability and eliminate some system crash scenarios.

CSCvf78458

Symptom: The system will stop working or reboot during OS operation with PROCHOT, MEMHOT, and DMI Timeout-related events reported in the System Event Log (SEL).

Conditions: C220-M4 or C240-M4

Workaround: No workaround is available.

This bug fix changes the BIOS option "Package C-State limit" default value from C6 Retention to C0/C1 to help increase system stability and eliminate some crash scenarios.

Once upgraded, reset the BIOS settings to default or manually change Package C-State limit to C0/C1.

Interoperability with Other Clients

This section describes the interoperability of controller software with other client devices.

The following table describes the configuration used for testing the client devices.

Table 7. Test Bed Configuration for Interoperability

Hardware or Software Parameter

Hardware or Software Configuration Type

Release

8.8.x.

Cisco Wireless Controller

Cisco 5520 Wireless Controller

Access Points

AIR-CAP3802E-B-K9, AIR-AP1852E-B-K9

Radio

802.11ac, 802.11a, 802.11g, 802.11n (2.4 GHz or 5 GHz)

Security

Open, PSK (WPA-TKIP-WPA2-AES), 802.1X (WPA-TKIP-WPA2-AES) (EAP-FAST, EAP-TLS)

RADIUS

Cisco ACS 5.3, Cisco ISE 2.2, Cisco ISE 2.3

Types of tests

Connectivity, traffic (ICMP), and roaming between two APs

The following table lists the client types on which the tests were conducted. Client types included laptops, handheld devices, phones, and printers.

Table 8. Client Types

Client Type and Name

Driver / Software Version

Laptops
Acer Aspire 15 Windows 8 Home Qc Atheros Qca9377 11.0.0.492
Acer Aspire E15 Windows 8 Qc Atheros Qca9377 15.1.1.1
Acer Aspire E 15 Windows 8.1 QC Atheros Qca9377 11.0.0.492
Acer Aspire E15 Windows 8.1 Pro Qc Atheros Qca9377 11.0.0.492
Dell Inspiron 15 7569 Windows 10 Home Ntel Ac 3165 18.32.0.5
Dell Latitude 6430 Windows 8.1 Pro Intel 6205w8 15.16.0.2
Dell Latitude E5430 Windows 7 Intel Centrino N 6205 15.17.0.1
Dell Latitude E5450 Windows 7 Professional Intel 7260 18.33.6.2
Dell Latitude E5540 Windows 7 Intel Dualband Ac7260 1.566.0.0
Dell Latitude E6430 Windows 7 Professional Intel Centrino Ultn6300 15.9.2.1
Dell Latitude E6430 Windows 7 Professional Intel 6250 15.11.0.7
Dell Latitude E6430 Windows 7 Professional Intel 3160 6.30.223.215
Dell Latitude E7450 Windows 7 Professional Broadcom 1560 15.1.1.1
Dell Latitude Windows 8.1 Pro Intel Ac7260 18.33.3.2
Fujitsu Lifebook E556 Windows 10 Pro Intel 8260 11.0.0.492
Lenovo Yoga 460 Windows 10 Pro Intel Ac8260 19.1.0.4
Macbook Air Mac OS Sierra 10.12.3 Broadcom Bcm43xx 1.0 6.30.225.29.1
Macbook Air Macos Sierra 10.12.6 Broadcom Bcm43xx 1.0 7.21.171.68.1a4
Macbook Air OS X Yosemite (10.10.5) Broadcom Bcm43xx 1.0 7.15.166.24.3
Macbook Mac OS Sierra 10.12 Beta Broadcom Bcm43xx 1.0 7.21.149.34.1a7
Macbook Pro Mac OS Sierra 10.12.4 Broadcom Bcm43xx 1.0 7.21.171.68.1a4
Macbook Pro OS X 10.8.5 Broadcom Bcm43xx 1.0 5.106.98.100.17
Macbook Pro Retina Mac OS Sierra 10.12.3 Broadcom Bcm43xx 1.0 7.15.166.24.3

Tablets
Apple iPad iOS 9.3.1
Apple iPad mini iOS 12.0
Apple iPad mini 2 iOS 10.3.1
Apple iPad Air iOS 10.1.1
Apple iPad Air 2 iOS 10.2.1

Mobile Phones
Apple iPhone 4S iOS 8.0
Apple iPhone 5 iOS 10.3.1
Apple iPhone 5C iOS 9.3.2
Apple iPhone 6 Plus iOS 12.0
Apple iPhone SE iOS 10.3.1
AT100 Toshiba Android 4.0.4
Cisco 7925G-EX CP7925G-1.4.8.4.LOADS
Cisco 7926G CP7925G-1.4.8.4.LOADS
Cisco 8821 sip8821.11-0-4-14
ET1 Android VERSION 2.3.4
ET5 Android 5.1.1
LG-D855 LG Android 5.0
Mediapad X1 7.0 Huawei Android 4.4.2
Moto X 2nd Gen Motorola Android 5.0
One Plus One One Plus Android 4.3
One Plus Three One Plus Android 6.0.1
Samsung Galaxy S4 Samsung Android 4.2.2
Samsung Galaxy S4 Samsung Android 5.0.1
Samsung Galaxy S6 Samsung Android 7.0
Samsung Galaxy S6 Samsung Android 6.0.1
Samsung Galaxy S8 Samsung Android 7.0
Samsung Tab Pro Samsung Android 4.4.2
SM-P600 Samsung Android 4.4.2
SM-T520 Samsung Android 4.4.2
TC510K Zebra Android 6.0.1
TC8000 Zebra Android 4.4.3
8742 Spectralink Android 5.1.1
8744 Spectralink Android 5.1.1 2.5.0

Key Features Not Supported in Cisco WLC Platforms

This section lists the features that are not supported on various Cisco WLC platforms:


Note

In a converged access environment that has Cisco WLCs running AireOS code, High Availability Client SSO and native IPv6 are not supported.

Key Features Not Supported in Cisco 3504 WLC

  • Cisco WLAN Express Setup Over-the-Air Provisioning

  • Mobility controller functionality in converged access mode

  • VPN Termination (such as IPsec and L2TP)

Key Features Not Supported in Cisco 5520 and 8540 WLCs

  • Internal DHCP Server

  • Mobility controller functionality in converged access mode

  • VPN termination (such as IPsec and L2TP)

  • Fragmented pings on any interface

Key Features Not Supported in Cisco Virtual WLC

  • Cisco Umbrella

  • Software-defined access

  • Domain-based ACLs

  • Internal DHCP server

  • Cisco TrustSec

  • Access points in local mode

  • Mobility or Guest Anchor role

  • Wired Guest

  • Multicast


    Note

    FlexConnect locally switched multicast traffic is bridged transparently for both wired and wireless on the same VLAN. FlexConnect APs do not limit traffic based on IGMP or MLD snooping.

  • FlexConnect central switching in large-scale deployments


    Note

    • FlexConnect central switching is supported in only small-scale deployments, wherein the total traffic on Cisco WLC ports is not more than 500 Mbps.

    • FlexConnect local switching is supported.

  • Central switching on Microsoft Hyper-V deployments

  • AP and Client SSO in High Availability

  • PMIPv6

  • Datagram Transport Layer Security (DTLS)

  • EoGRE (Supported only in local switching mode)

  • Workgroup bridges

  • Client downstream rate limiting for central switching

  • SHA2 certificates

  • Cisco WLC integration with Lync SDN API

  • Cisco OfficeExtend Access Points

Key Features Not Supported in Access Point Platforms

This section lists the features that are not supported on various Cisco Aironet AP platforms:

Key Features Not Supported in Cisco Aironet 1800i, 1810 OEAP, 1810W, 1815, 1830, 1850, 2800, 3800, and 4800 Series APs

For detailed information about feature support on Cisco Aironet Wave 2 APs, see:

https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-7/b_feature_matrix_for_802_11ac_wave2_access_points.html.

Table 9. Key Features Not Supported in Cisco Aironet 1800i, 1810 OEAP, 1810W, 1815, 1830, 1850, 2800, 3800, and 4800 Series APs

Operational Modes

  • Autonomous Bridge and Workgroup Bridge (WGB) mode

  • Mesh mode

  • LAG behind NAT or PAT environment

Protocols

  • Full Cisco Compatible Extensions (CCX) support

  • Rogue Location Discovery Protocol (RLDP)

  • Telnet

  • Internet Group Management Protocol (IGMP)v3

Security

  • CKIP, CMIC, and LEAP with Dynamic WEP

  • Static WEP for CKIP

  • WPA2 + TKIP

    Note 
    WPA +TKIP and TKIP + AES protocols are supported.

Quality of Service

Cisco Air Time Fairness (ATF)

FlexConnect Features

  • Split Tunneling

  • PPPoE

  • Multicast to Unicast (MC2UC)

    Note 

    VideoStream is supported

  • Traffic Specification (TSpec)

    • Cisco Compatible eXtensions (CCX)

    • Call Admission Control (CAC)

  • VSA/Realm Match Authentication

  • SIP snooping with FlexConnect in local switching mode

Note

For Cisco Aironet 1850 Series AP technical specifications with details on currently supported features, see the Cisco Aironet 1850 Series Access Points Data Sheet.

Key Features Not Supported in Cisco Aironet 1800i, 1810 OEAP, and 1810W Series APs

Table 10. Key Features Not Supported in Cisco Aironet 1800i, 1810 OEAP and 1810W Series APs

Operational Modes

Mobility Express

FlexConnect Features

Local AP authentication

Location Services

Data RSSI (Fast Locate)

Key Features Not Supported in Cisco Aironet 1830, 1850, and 1815 Series APs

Table 11. Key Features Not Supported in Cisco Aironet 1830, 1850, and 1815 Series APs

Operational Modes

Mobility Express is not supported in Cisco 1815t APs.

FlexConnect Features

Local AP Authentication

Location Services

Data RSSI (Fast Locate)

Key Features Not Supported in Mesh Networks

  • Load-based call admission control (CAC). Mesh networks support only bandwidth-based CAC or static CAC

  • High availability (Fast heartbeat and primary discovery join timer)

  • AP acting as supplicant with EAP-FASTv1 and 802.1X authentication

  • AP join priority (Mesh APs have a fixed priority)

  • Location-based services

Key Features Not Supported in Cisco Aironet 1540 Mesh APs

  • Dynamic Mesh backhaul data rate.


    Note

    We recommend that you keep the Bridge data rate of the AP as auto.

  • Background scanning

  • Noise-tolerant fast convergence

Key Features Not Supported on Cisco Aironet 1560 APs

  • MAC Authentication FlexConnect Local Authentication

  • Noise-tolerant fast convergence

  • Static WEP

Caveats

Open Caveats

Table 12. Open Caveats

Caveat ID Number

Description

CSCvg76166

Channel Utilization changes to 0% on Wave 1 Marvell APs

CSCvg91770

1810W AP stops to send data frame intermittently

CSCvg93221

802.11AC wave2 outdoor APs do not support all MESH modes for multicast

CSCvh81618

When adding a member to RF Group with Static Leader 8510, group size exceeded error

CSCvi06408

Wave 1 AP failed to send DHCP packet to wired side under VLAN Override

CSCvi38539

AP stops forwarding IPv6 Router Advertisements to random clients

CSCvi48503

Standby WLC constinuously reboots with "Reason: XMLs were not trasferred from Active to Standby"

CSCvi55945

8.8:NBN AP Neighbor Info show backhaul CH missing vs. CLI for 40MHz backhaul and Rate mismatched

CSCvi69688

8.8 - No of RUN state clients in standby is more than Active Controller.

CSCvi77694

WLC leaks dyn interface traffic from untrusted VLAN to trusted VLAN while in cntrl webauth req state

CSCvi80205

ETSI domain Compliance and Throughput testing

CSCvi82147

Failed to set Country Codes when WLC has redundant country codes CA2, KR, PH2, US2, USL, USX

CSCvi82746

Cisco WLC running 8.5.120.0 release reloads unexpectedly with Task Name SISF BT Process

CSCvi92170

Cisco 1800 series APs falsely shows 100% channel utilization on 5GHz

CSCvi96793

R0KHId and R1KHID going zero in assoc response for IPhone on 8.6 ME, causing connectivity issue.

CSCvi98368

AP 1815I stops working due to kernel panic in radio driver, PC is at ieee80211_node_unauthorize+0x48

CSCvi98415

AP 1815I stopped working due to kernel panic during radio reset in 8.3.140.0

CSCvj06563

AIROS WLC crashed at mmListenFsm with config mesh subset-channel-sync enable in IRCM with ewlc

CSCvj06837

MAP Wave 1 AP mesh security failures after roaming between 2 parents

CSCvj08387

WLC stopped working on spamApTask6

CSCvj11716

WLC failed to apply flex-acl returned from RADIUS server - policing not working, client passing traf

CSCvj23235

WLC: Need to change active fall-back of AAA probing w/probes of 'dead' RADIUS server

CSCvj23415

8.8: Wave 2 or Wave 1 AP cannot swap image after pre-download image completed successfully

CSCvj29870

8.8:Space detected on UI but CLI cannot for "flexconnect acl url-domain url"/"ext-webauth-url"

CSCvj30568

1832 AP stopped working due to beacon stuck, QCA case 03406780

CSCvj31604

8.8:"<IP addr> should be non zero and must have contiguous ones" but 0.0.0.0 can/ no sense for ones

CSCvj32199

SSH/Management Access of Primary WLC not possible when HA failover occurs in 8.5.120.0

CSCvj34879

AP reporting MD5 mismatch on poller script after running all flash bug fixes

CSCvj42758

RADIUS auth server insertion not proper with RADIUS DNS returning multiple entries

CSCvj43325

AP1850 running 3.7.5 is deauth client when received 2 assoc_req with same snonce

CSCvj50741

8.8: Clients get disconnected while AP joining back the WLC

CSCvj52635

ME Subordinate AP may send Disassociation after primary AP failover

CSCvj53235

Local policy using HTTP device profiling does not get applied to client.

CSCvj56689

8.5 MR3: AP1850 stopped working due to OOM

CSCvj58436

OID not increasing error when doing an IPv6 host query

CSCvj58606

8.8 ME: EoGRE Gateway entry gets removed from the AP when the tgw is down

CSCvj60609

vWLC Webauth not working

CSCvj65449

AIR-AP1562D-E-K9 with regulatory domain Kazakhstan does not join the WLC

CSCvj65592

Client static DNS ip support for openDNS

CSCvj69083

Guest user is removed from Standby controller after WLC reset

CSCvj69417

Wave 1 AP sends ACK at supported data rates

CSCvj70836

"show system slabtop" command not showing the system details

CSCvj72076

AP1800 drops a lot of packets

CSCvj72136

Barbados AP (2800/3800) loses its default gateway reachability

CSCvj73077

1810W APs may have power denied from older POE 802.3af switches

CSCvj73809

WLC: Invalid parameter specified error in CLI when trying config change

CSCvj74163

Monitor mode should not be allowed for AP1542

CSCvj74263

IPsec profile showing junk characters in show logging

CSCvj76009

Alpha 3800/2800 multiple WSA Agent process running, that might be the cause of OOM trigger

CSCvj76143

EoGRE tunnel profile VLAN is allowing to add alphanumeric values instead of numeric values

CSCvj79479

Cisco 8500 Wireless LAN Controller Web Interface Unvalidated Redirect Vulnerability

CSCvj79841

3802 AP unexpected reboot on 8.2.167.1

CSCvj79842

WLC does not reply keepalive and causes APs to drop line

CSCvj80129

Wave 1 AP uses invalid CAPWAP-Data keep-alive source port

CSCvj80359

Stale client entries exist in temporary data in Active WLC

CSCvj80688

Web: Remove APs or add APs in AP group pointing to main page if you try to add or remove APs

CSCvj80969

AP1530:8.3.141.153 5ghz 40 and 20Mhz Upstream Minimal TP drop is seen for Smaller packet size

CSCvj81510

When saving config on 1815I, UI throws error which does not tell the user about why it is failing

CSCvj82636

Client getting redirected to internal webauth instead of External webauth URL configured on AP Group

CSCvj83144

Able to configure the WLC interface without assigning any port from virtual wlc (vWLC) GUI

CSCvj83372

AP 1852 showing irregular data usage

CSCvj83659

8.8:Queueing WMI command back to TxQueue and buff leak messages on flex ap console

CSCvj85461

Disabling Data Rates of 6 or below disables 11 Mbps as well on Mobility Express UI

CSCvj86238

WLC stops working as emWeb spikes to 100% CPU usage after executing "show run-config"

CSCvj86324

1700 AP stopped working multiple times - SYS-2-CHUNKBADMAGIC: Bad magic number in chunk header

CSCvj88091

custom-web ext-webauth-url getting corrupted with customer configuration

CSCvj88099

UsmDb:HA_send_usmDbSxpPeerConnectionSet, ErrType:Apply Config failed, Reason:19

CSCvj88984

FlexConnect efficient upgrade disables when invalid configuration is provided

CSCvj91539

3800 AP stops working at sxpd process during SGT-IP binding exchange with peer switch

CSCvj91645

Clients not getting exported to anchor on New Mobility

CSCvj91805

WLC not providing error message while creating wrong IPv6 address

CSCvj93292

IOS AP is changing to sensor mode without WSA enabled from AP console

CSCvj94236

AP: Radio Init failed causing multiple wcpd crashes

CSCvj94659

Unable to update TACACS+ DNS parameters on configuring IPv6 DNS server under global settings

CSCvj94880

1810W - Clients not getting DHCP

CSCvj94919

702w AP running vlan ID is NA after AP reboot

CSCvj95739

Standby failing to add exclusion client - exclusion client mismatch between Active and Standby WLC

CSCvj96809

8.8_ Edit all page in mobility is not working properly, when encryption is enabled

CSCvj96920

8.8 NBN: Unable to add Flex WLAN-ACL mapping on AP until WLAN is enabled at least once

CSCvj97430

Mobility Express AP - Loop detected causes AP reboot

CSCvj98913

8.8 - "%ACL-3-RULE_DONOT_EXIST: [SA]ace_api.c:983 Unable to get IP address parameter" msg in msglog

CSCvj98950

Primary/Secondary Backup-controller config with v6 address fails for Click AP

CSCvj98989

On every execution of "show capwap client ha" appends "set_snap"

CSCvk00884

The WLC is replying with the wrong value for the following OID: bsnAPIfProfileParamAssignment

CSCvk00889

3802/2802 APs with -S domain rejected to join the switch due to Invalid regulatory domain.

CSCvk02153

Wave 1 AP WLAN Client Stats cldcClientDataRetries counter is zero

CSCvk03686

EoGRE client count is not getting cleared in Standby on switching SSID

CSCvk03882

Sensor mode AP coming as FlexConnect after ME forced failover

CSCvk09513

AP is not downloading the WLC 85Mr3 image rather it says image is already in the backup

CSCvk09627

In 8.9.1.60 in WLC "show ap config 802.11a <ap_name>" unable to print the correct Bandwitdth

CSCvk09764

WLC8.8 Smart License: AP In Use Count does not go UP when new APs are joining

CSCvk09888

AP1815 stopped working while changing mode from FlexConnect to local

CSCvk10190

8.8: HA sync failure: UsmDb:HA_send_usmDbSpamSetApMode, ErrType:Apply Config failed on Standby

CSCvk10891

8540: High latency under load with AVC, TCP fragmentation

CSCvk12146

Spurious messages getting printed on Barbados AP while Enable/Disable wlan

CSCvk12422

ME Controller rebooting twice after LSC AP Auth State to 802.1x port authentication /both

CSCvk13835

Sensor mode APs is not downloading the image after primary failover

CSCvk14062

ping delay happens with other traffic load

CSCvk14080

8.8: Standby WLC reboot with IPC failures: RP back to back connected

CSCvk14267

Observed XML and Invalid config during upload/download WLC config.

CSCvk14419

In WLC GUI with read only mgmt user able to ping LDAP server IP

CSCvk15043

Wave 1 APs - AP radio FW image install failure in the bootup loop

CSCvk15527

EoGRE tunnel configuration is not pushed to APs when AP moved from one WLC to another

CSCvk16522

show logging config-history and show logging last-reset issues

CSCvk17291

Operating system info missing on client 360 page for macos only

CSCvk17426

ME: ACLs are getting deleted after upgrade

CSCvk18752

Incorrect VCI string of DHCP option 60 on AP 1815

CSCvk19951

AP exec timeout value is not reflected properly

CSCvk20402

Last reset details not showing after reset/upgrade/downgrade

CSCvk20899

AP4800 "vendor_send_mgmt_frame VAP 14 is not up" message flooding console

CSCvk21153

AP3800: TxPower changes after moving channel and back to orginal channel

CSCvk22312

hotspot2 OSU SSID is picking profile name

CSCvk23248

ME controller rebooting twice after changing the LSC AP Auth configuration in UI

CSCvk23423

WLC GUI displaying error message while disabling dhcp proxy-mode

CSCvk23577

Client is unable to connect due to "Failed to create a timer"

CSCvk23664

8.8: FlexConnect split tunnel does not work when the ACL is configured in FlexConnect group

CSCvk23822

In 8.8.1.161 TP drop is observed in Downstream with 5ghz 80/40/20 Mhz in all packets size

CSCvk24360

WLC power supply status is incorrect when there is no power supply

CSCvk24427

Traps related to protocol pack load not sent on installing AVC protocol pack

CSCvk26002

Mesh links are not shown on Outdoor Area View if APs are in FlexBridge mode

CSCvk26519

1562 MAP stops sending Block ACK once the 1572 RAP moves to another WLC

CSCvk26539

AP1815 intermittently dropping packets

CSCvk26545

In 8.8.1.182 AP2700 TP drop in Upstream for 5Ghz 80/40/20 Mhz across all packet size

CSCvk26563

AP1810W 5G radio FW assert @0x009A4F9F 8.2.170.4

CSCvk26607

Global Multicast is disabling after ME reset

CSCvk27093

NAS-ID in WLAN cannot be changed in the startup-command after you saved once

CSCvk27250

System not operational with task apfRogueTask_3

CSCvk28143

WLC crashed with SNMPTask in 8.5.137.10

CSCvk28371

hotspot2 OSU SSID is picking profile name

CSCvk29178

1550 BVI interface uses a different MAC-Address than the Gigabit interface

CSCvk30585

8.8_"Missing 802.1X or client control block" Errors in WLC Message Logs

CSCvk30807

Wave 1 AP mesh AP reloading due to Reload requested by Net Background

CSCvk31484

Upstream traffic rate is slow via specific Wave 2 AP

CSCvk32494

Encrypted mobility:UI throws wrong error message while adding mobility peer

CSCvk33107

8.8: Clients not able to connect due to M2 MIC failure

CSCvk35047

WLC stops working when LAG mode is enabled on the AP

CSCvk35275

5508 WLC stopped working at Task Name - EAP_Framework_0

CSCvk36257

8.8 - Local-Split WLAN-ACL mapping is retained at AP after it is removed from WLC

CSCvk36463

Support Bundle output only genertaes WSA core bundle when WSA is enabled

CSCvk36887

Some clients cannot associate because their entry is not getting deleted at the WLC.

CSCvk37153

8.8 - 6K entries of "config ap syslog host global <IP>" in uploaded config

CSCvk37576

SessionID should be added and decoded from Handoff packet.

CSCvk37877

TACACS user:Getting faild msg"SNMPv3 user lockout attempts configuration failed"

CSCvk39841

Change SSID name with SNMP fails with commitFailed

CSCvk39948

WLC is not returning the expected prompt when logging in via SSH

CSCvk40074

Switchdrvr unresponsiveness triggered by DB services crash

CSCvk40132

8.8: UI accepts Prefix length 0 with error static IPv6 configured, but incorrect IPv6s or missing/

CSCvk40571

Partial Collection Failure state for WLC 3504

CSCvk41068

Advance IPMI is not set and causing fan noise

CSCvk41447

AP auth local user authentication fails once deleting and adding the local user back

CSCvk41500

Hotspot is enabling with Open/Guest security after change from WPA Enterprise

CSCvk41512

APX800 sniffer mode not sending frames with AMSDU 1500 Bytes to destination

CSCvk41583

Local Split traffic is goes through after removing ACL mapping

CSCvk41963

Observed "print_backtrace+48" message on all ME

CSCvk42191

AP3800 advertises RSN IE for an OPEN SSID.

CSCvk42314

8.8:"show client summary" pegged an extra count 1 without client data once a while periodically

CSCvk42592

Disabling "Out of box" in RF Profiles throws SNMP error

CSCvk42619

Client RF stats are not cleared when client role moving from Local to Export-Anchor

CSCvk43025

Local Split and Central path traffic stops after some time with 2800 APs

CSCvk43114

[SDA] WLC with a sensor AP is generating a "URL not reachable" error every hour

CSCvk43433

Passphrase as hex value is not supported in ME GUI for PSK WLAN

CSCvk44045

8.8:Config static IPv4 but still using DHCP IPv6 due to no reboot after IPv4 accepted

CSCvk44089

8.8:Note 8/Galaxy S7 Device Type improper, Local Profiling miss "Apple" for Manufacture Stats

CSCvk44492

WiSM2 continuously reloads without crash file

CSCvk44831

LSC cert:Click-AP not taking configured LSC cert keysize.

CSCvk45259

In Build 8.5.134.106 AP 2700 TP drop with 2% is seen in 5Ghz Downstream

CSCvk45492

AP TrustSec: AP does not retain CTS SXP peer connection and disabling CTS SXP state after reload

CSCvk46817

AIR-AP2802I not sending beacons with both radios in 5GHz

CSCvk46867

8.8: Unable to transfer code between HA controllers

CSCvk47740

Pre-auth ACLs are not configuring for RLAN in ME UI

CSCvk47879

Silent crash on WLC 5508 due to growing memory utilisation

CSCvk47937

Local-Split - Local traffic is failing when VLAN Tag is enabled.

CSCvk47949

Local-Split- Traffic to Local network fails after roaming from one ap to another in flexgroup

CSCvk51102

iOS captive portal taking 45 seconds to trigger in Local Web-Auth

CSCvk51464

8.8 ME: ME GUI doesn't display the IP the internal AP is using but rather the main IP

CSCvk51634

Wave 2 Flex Efficient Upgrade fails as primary AP sends empty image_str to WLC

CSCvk52144

8.5: SSH connection to WLC is not going through after longevity and stress conditions

CSCvk52187

Unable to configure TGW list with TACACS controller user in WLC UI

CSCvk52210

Cannot configure Management IP when WLC is in maintenance mode.

CSCvk52381

DNS-ACL - Webauth Redirect page is not working properly in CWA case

CSCvk52704

"config network multicast l2mcast disable <interface>" config is not blocking L2 mcast traffic

CSCvk52808

8.8 - SSH session closed with message "Incoming packet was garbled on decryption"

CSCvk52883

8.8:Local Profiling UI shows Manufacture Stats issues

CSCvk53015

IOS AP mapping incorrect FlexConnect VLAN

CSCvk53499

APs doesnt reconnect back, error log: System reached max concurrent DTLS Handshakes

CSCvk53511

8.5MR: 3504 Anchor WLC has multiple stale client entries after longevity/traffic test

CSCvk53743

8.5_New mobility:UI throws wrong error message while adding used public IP

CSCvk53873

8.5MR: Bulk sync completion traps flood from the Active WLC

CSCvk53963

DNS-ACL - 1815 ME switchdriver crashed in 8.8.2.18

CSCvk54001

IRCM: v6 peers not synched to standby - UsmDb:HA_send_usmDbMmMwarAddIPv6, ErrType:Apply Config fail

CSCvk54272

8.5MR: 3504 WLC stops working on task: reaperWatcher during webauth testing

CSCvk55651

AP1852 failure of association due to set CAPWAP tunnel failed

CSCvk56120

ME: Unable to create IPv6 ACL after creating and deleting multiple ACLs

CSCvk56509

Mobility:Edit all page hangs when some mobility group member doesn't have req args

CSCvk57014

AP: Sometimes creates empty radio core files without any information

CSCvk57269

Sanity: ME-4800 multicast traffic did not pass, tested with internal AP

CSCvk57361

FQ NMI reset on 2802 AP mrvlfwd dies

CSCvk58160

Stress test: AP1552H RAP stops working when AP CPU hits nearly 100 percent usage

CSCvk58429

WLC shows wrong pop-up when downloading web-auth certificate

CSCvk58501

AP radio unresponsiveness happened because of beacon stuck

CSCvk58625

Wireless management interface change should not be allowed when IPsec is enabled

CSCvk58924

8.5MR4 - IPv4 ACL is wrongly externalized in case of Flexconnect Local Switching.

CSCvk59040

8.5MR: 3504 mGig port should be allowed to be disabled when not mapped to MGMT/RMI interface

CSCvk59252

8.5MR: Service port configuration is lost after switchover

CSCvk59259

8.5MR4 - 3504 standby controller rebooted (Standby IPC failure) instead of maintenance state

CSCvk59498

AP3702 High CPU Utilization under NCI Rx. Unable to join WLC

CSCvk60394

2700 AP not ACK on QoS data packet from client occasionally

CSCvk60596

8.5MR4 - Clients/Security/eap-type is externalized as 3 when EAP-FAST is selected

CSCvk60986

AP CAPWAP MTU discovery fails for CAPWAP data

CSCvk61078

VLAN priority tag inside the EoGRE packet set to non-zero when 802.1p set to none in LOCAL mode

CSCvk61124

Samsung TV drops connection on its mgmt server due to incorrectly assemabled Packets received 1810w

CSCvk61577

AP: OOM stops working seen in 8.8.3.25 when intelligent capture enabled

CSCvk61599

RADIUS does not fall back to primary RADIUS server.

CSCvk61968

Incorrect QoS marking for upstream traffic when connecting Platinum WLAN

CSCvk62008

Sometimes AP does not send EAPOL frame after client reassociation

CSCvk62025

DNS-ACL- Wild card entry for v4 ACL is not getting applied in Client when v4 and v6 acls are used

CSCvk62034

DP stops working on WLC running 8.2.154.53

CSCvk62093

8.5MR4 - Non-Flexconnect IPv6 ACL is applied for Local switching Client

CSCvk62240

WLC Smart license 8.8: The license summary(information) is not syncing in after switchover

CSCvk62355

AP2800 running ME image 8.6.101.0, 8.7.106.0 crash in ewsContexSendRedirect200->ewaDate

CSCvk62680

WiSM2 not releasing licenses after reboot

CSCvk62909

Device profile does not work for certain Android phones. Profiled as Linux-workstation

CSCvk62915

'Nearby AP' stats shown multiple times with different dBm values for the same slot

CSCvk63215

Cisco 1852 series APs Kernel Panic due to NSS memory corruption

CSCvk63291

WGB not responding M3 message on 4-way handshake

CSCvk63452

8.5MR4:2800/3800 XOR CleanAir state is Down when Band in 160MHz while Up for 20, 40, 80MHz

CSCvk63459

3802, 4800 AP drops packets larger than 1426 (inner IP) with VxLAN

CSCvk63784

8.5MR4 - Error String is not getting updated in Last Error field in "show network assurance summary"

CSCvk64669

8.8.3.22 AP2700 TP drop is seen in Downstream and Upstream in 5 ghz 80/40/20 Mhz all packet size

CSCvk64674

Wave1 APs advertise Adaptive FT MDIE on probe response for open SSID

CSCvk64809

8.8 3504 WLC Mgig Stanby struck with ERROR: cvmx_cmd_queue_shutdown: Queue still has data in it.

CSCvk64829

Observing CMX Certificate error and WSA cert releated XML message on Mob Exp

CSCvk64928

AP stops working when we configure LSC keysize as 4096

CSCvk65128

8.5MR4:tar:can't open '/tmp/part.tar': No such file/"tar -xf /tmp/part.tar -C /bootpart/part2" fail

CSCvk65150

8.5MR4:UI pop-ups incorrectly when swap image fine, inconsistent error vs, CLI when image going

CSCvk65680

Profile: AP3602 has a radio core after transmitter seems to have stopped

CSCvk65886

Profile: AP3602 stops working in process Init after tracebacks with 8.5.137.24

CSCvk66354

8.5MR4 - GUI issues with Assurance Stats

CSCvk66635

8.5MR4: 3702NOS module AP stops working with Dot11 Driver

CSCvk66700

3500 series access point 5GHz radio stops working.

CSCvk66762

8.5MR4:Error sending/receiving register device request/rsp&ACT2 could not be registered in tam

CSCvk66896

FlexConnect AVC profiles not marking DSCP traffic

CSCvk66975

AP as a sensor reports all configured tests status as onboarding failure

CSCvk67140

Client unable to join SSID reason 54 from AP and WLC

Resolved Caveats

Table 13. Resolved Caveats

Caveat ID Number

Description

CSCvb26809

WLC should use port MAC for non LAG and box MAC for LAG

CSCvc62540

Smart Licensing next communication attempt pre-dates the controller time after reboot

CSCvc66728

WLC: Traceback pattern #2 on 8.2MR5 in apfProcessAssocReq

CSCvc80047

Unexpected AP reloads - dpaa_get_pool_id_from_ios_pool_ptr

CSCvd67485

Cisco 3700 AP Tx stop Radio reset due to false radio TX inprog count

CSCve64652

Cisco Access Point 802.11r Fast Transition Denial of Service Vulnerability

CSCve70752

SNMP issue: TX power level returns null causing Cisco PI, WLC sync to not update AP information

CSCve82488

Cisco Wave 2 APs in FlexConnect mode stop redirecting CWA clients after WLAN change

CSCvf10811

Sniffer mode APs should log more layer 1 information

CSCvf28459

Write of the Private File nvram:/lwapp_ap.cfg Failed on compare RCA needed (try = 1)

CSCvf31881

Cisco 2800 AP detects Intel Dual Band Wireless-AC 8260 as rogue client/AP

CSCvf63455

Linux Kernel 3.14.43 - inotify_handle_event() and vfs_rename() Privilege Escal ...

CSCvf66696

Cisco WLC Control &amp; Provisioning of Wireless Access Points Protocol Denial of Service Vulnerability

CSCvf66723

Cisco Wireless LAN Controller Directory Traversal Vulnerability

CSCvf80409

AP1815 not sending all traffic after period under load

CSCvf83391

Cisco 8.3 Release: AP reloads unexpectedly at TAMD ap-tam process

CSCvf86161

Bad magnitude calibration values in Triggerfish EEPROM

CSCvf89335

Cisco 3700 AP stopped working with memory allocation failure CAPWAP

CSCvf90411

[IOT 8.6 HSR]:IW3702 WGB radio 0 core after 30M up EAP-FAST security and script common cleanup

CSCvf99887

MAP Gigabit port being learned in Mesh management VLAN instead of client VLAN

CSCvg00507

Cisco 3700 AP reloads unexpectedly- PID 104: Process LWAPP Rogue Monitoring process

CSCvg07617

AP1810W:Kernel Panic reloads unexpectedly PC is at _ZN17ContentHashFilter11clear_staleEv+0x1ac/0x1d0

CSCvg18543

Cisco 3700AP TX jammed and radio reloads unexpectedly

CSCvg23810

PMTU change to 1500 from a lesser value is not reflected in AP

CSCvg28378

AP: cmd timeout AP radio reloads unexpectedly in 8.6 due to Rx hang

CSCvg35115

Cisco 3802 running 8.3.130 shows radio core without the crash file

CSCvg35220

Cisco 3702 AP- Fails to correctly map data traffic to SGACL

CSCvg35547

Cisco 3700 AP beacon stuck seen on 8.5.107.x image

CSCvg40339

Cisco 2800 AP in sniffer mode is missing huge amount of data packets

CSCvg40792

Client global IPv6 not correctly mapped to MAC address under certain conditions

CSCvg44450

Cisco 2800,3800,1560 AP cannot forward packets downstream; 'Failed to get ARP entry for WLC'

CSCvg53640

Cisco 1830 AP triggered FW assert for radio failure (beacons stuck)

CSCvg60758

Cisco Wave 2 APs drops TCP retransmit from server

CSCvg61878

Cisco Wave 2 APs: does not send k9w8 in LLDP Packets leading to false classification

CSCvg62039

False radar detection on AP 1832 with 40MHz CW

CSCvg62508

3702 AP sometimes maps SGT 0 to client even though ISE returns correct SGT

CSCvg67509

Cisco 1810W AP reloads unexpectedly over a kernel panic

CSCvg70352

Cisco 1832,1852 APs reloads unexpectedly due to kernel panic at 'kmalloc_poolid+0xb8/0x16c'

CSCvg70384

Cisco 1832/1852 AP radio reloads unexpectedly at 0x009A497D

CSCvg70787

8.6: 3802 Kernel panic PC is at skb_release_data+0xe0/0x230

CSCvg71816

Cisco 8510 controller: reaper reset due to unexpected reload with task tempstatus

CSCvg72918

Cisco 4800 AP on 8.7.1.x code configures channel of slot_0 band 5Ghz

CSCvg73522

Cisco 5508 WLC reloads unexpectedly due to memory leak in snmpApPowerTrap()

CSCvg73797

Cisco 2800, 3800 AP: Command timeout at 0x8000 in FW

CSCvg75182

MC:8.3MR4: Continuous stack trace print due to error on Wave 2 AP with 8.3.134.30

CSCvg75189

Cisco 1800 AP: Radio failure and firmware freeze

CSCvg75933

CPU ACL does not block webauth related ports

CSCvg76168

Cisco 1532AP 5GHz radio interface remains down due to DFS even when not all channels are in blocked list.

CSCvg77711

System reloads at random on running mesh commands

CSCvg78210

AP syslog config does not change level from AP syslog to informational it remains in emergencies

CSCvg78624

Cisco 2800, 3800 APs: channelization issue, all the APs are stuck on channel 36

CSCvg79381

AP: AP failed to send ApSecurityContext; resulting all hyperlocation dropped by CMX

CSCvg82066

Cisco 1815I AP reloads due to kernel panic

CSCvg82156

Cisco 2802E AP: Radio1 reloads unexpectedly

CSCvg82215

Silent reloads, data plane crashes, high latency when WLC receives jumbo frames

CSCvg82450

[vEWLC]:After SSO, wired-wireless and wireless-wireless traffic drops for 4-12 seconds.

CSCvg82672

NAT-PAT- AP losing NAT translation entry for ongoing continuous client traffic

CSCvg82784

Cisco Wave 2 APs start the Channel Availability Check (CAC) timer after rolling to a lower bandwidth

CSCvg83836

Clients cannot pass traffic with 1810W MAB FlexConnect local switching RLAN

CSCvg84824

AP Sensor: Does not forward DHCP offer data packet to sensor client over the air

CSCvg84897

AP-4800: XOR radio Rx-SOP threshold remains same after changing band from 2.4 GHz to 5GHz

CSCvg85175

Cisco WLC reloads unexpectedly with task name spamApTask0

CSCvg86324

WLC reloads unexpectedly with SNMP operation with Flex ACL

CSCvg86741

vEWLC:SGT tag not getting deleted when client is in webauth_pending

CSCvg87401

Cisco 1542 AP reloads unexpectedly when in Flex + Mesh mode

CSCvg87547

AP: Client disconnected due to idle timeout wrongly kicking in when client is going to power save

CSCvg88269

CTS-SXP default password not retain after upload and download the config.

CSCvg89145

[cmd timeout] wifi1: 0x801f=unknown intCode:0x001f last 0x8120=unknown

CSCvg89442

Cisco 5500 and 8500 Series Wireless LAN Controller Information Disclosure Vulnerability

CSCvg89705

Cisco 8540 standby WLC reloads unexpectedly on rsyncmgrIpcqTask while disabling HA

CSCvg89807

Silver QoS profile is assigned to RLAN when configuration is imported

CSCvg90113

8.7: AP removing the client wrongly though IPv6 pre-auth ACL present in the database with URL rules

CSCvg91108

WQE size constantly increasing, error messages

CSCvg91708

WLC emweb reloads unexpectedly at commandConfigSpamApAntennaMonitor

CSCvg91734

Cisco 1852/1832 AP: AP data traffic stall in HD environment

CSCvg91811

Cisco 4800 FW freeze on radio 1

CSCvg93191

Cisco 3800 AP beacon stuck when radio reloads unexpectedly with signature 'B0B0'

CSCvg94522

TxFSM stuck on Radio 0 with new signature

CSCvg94718

Standby WLC reloads unexpectedly on spamApTask

CSCvg94780

Cisco WLC reloads unexpectedly on 8.5.105.0 release

CSCvg94967

8.7.1.79 - Cisco 2800, 3800 APs ASKU - Unable to push config for APBeacon V-Ibeacon profile

CSCvg95476

Cisco 1810,1850 AP reloads unexpectedly with switch behind RLAN/Aux Port

CSCvg96160

Cisco WLC reloads unexpectedly after 1-day on 8.7 Alpha

CSCvg96183

Proxy ARP always enabled in Beacon IE for Flex mode AP irrespective of ARP cache config

CSCvg96852

Cisco 1815W SnifferMode AP beacons allows clients to join and blackhole traffic

CSCvg96864

Cisco 8.5MR1 to 8.5.107.110 Releases - Cisco 3702 AP radio core with reason 'Bad acq dtx'

CSCvg97013

Cisco 8540 WLC reloads unexpectedly on Task Name: emWeb on 8.5.110.0

CSCvg97208

Cisco 1852AP: Apple clients connection fails in 802.11r adaptive mode in WLAN

CSCvg97712

Cisco 1850 AP console flooded with 'Total NR report Length exceeds Max Buffer Size -1067447752'

CSCvg98048

Sensor: Getting error during test run: CRITICAL - Stuck at test index -1 Will restart WSA !

CSCvg98078

AP with Flex AVC visibility Tx frames with sequence jumps causing client to not process packets

CSCvg98786

IOS AP DTLS flap issue seen in pre commit sanity

CSCvg99101

MC:8.5:Radio FW crash seen on Cisco 1850 APs @0x009A646B

CSCvg99108

8.5 MR1 on Cisco 2702 AP reloads unexpectedly on dot11_rm_offchan_handle_fw_response_isr

CSCvg99310

8.7: AP IPv6 URL ACL rule miss-match leads to client packet drop

CSCvg99890

config certificate generate line of uploaded config is corrupted

CSCvh00153

Download of PKCS12 bundle failed for EAP-TLS WLAN

CSCvh00256

Cisco WLC has multiple open ports, cannot be properly secured

CSCvh00398

WSA: Flex RADIUS Stats data parsing fails

CSCvh01089

False beacon stuck issue due to no beacon updates in WCP message Host triggered a radio freeze

CSCvh01470

Cisco 5520, 8540 WLC: Little Endian issue while adding rules in iptables for snmptrap over IPsec

CSCvh02937

Sensor: wireless sensor is choosing SSIDs with very poor signals during Cisco Provisioning

CSCvh03995

WLC 3504: Returns error code 500 / unauthorized token error when trying to send data to Assurance

CSCvh04880

Sensor: Intermittent connectivity issues with EAP-FAST security

CSCvh05749

AP IP address showing as '0.0.0.0' on GUI while downloading new image

CSCvh07545

Cisco 2800, 3800APs Kernel Panic due to processing of Rx frames before driver is initialized

CSCvh08020

AP stuck in AP after upgrade: flashfs[0]: writing to flash handle Illegal Operation

CSCvh11158

Cisco Wave 2 APs do not apply TCP adjust MSS on Fabric or Flex local SSIDs

CSCvh11212

WLC with Internal DHCP not sending NAK

CSCvh12081

Time not synced with Version 4 and getting unwanted message and NTPQ status also not showing

CSCvh12398

8.7: IPv6 enforcement not working with 8.8.1.8

CSCvh12504

8.7: IP learning not happening for IPv4 URL ACL on configuring both IPv4 and IPv6 pre-auth ACLs

CSCvh12768

IOS 3700 AP could not join WLC over CAPWAPv6 tunnel using DHCPv6 address

CSCvh12943

Cisco 2800,3800APs on 87 code TLV-DEC-ERR-1 No proc for 1912,TLV-DEC-FAILED for TLV_VAP_PAYLOAD(276)

CSCvh14509

Queue full issue observed with NmspNormalTxQ, breached 1 time. having Capacity 65535

CSCvh14849

8.7:'Disable' selected for 'fabric' cannot filter qualified APs out

CSCvh14989

Client in RUN state on anchor with 0.0.0.0 IP address

CSCvh15015

Level-1 list for Radio 0 is blank

CSCvh15852

WLC GUI/SSH not accessible - emweb consuming 100% CPU

CSCvh16413

WLC system reloads unexpectedly with apfRogueTask_0

CSCvh16970

Cisco WLC does not apply ACL Template from PI correctly

CSCvh18096

CPU ACL does not block HTTPS traffic to management interface from wired client

CSCvh18868

In VWLC unable to config WLAN once created through GUI

CSCvh19127

Cisco 1815I AP no response from wired side

CSCvh20238

Cisco 2800, 3800 APs joining the WLC in flex-mode fail to update FlexACL in group policies

CSCvh20731

WLC-HA: Certificate transfer during HA pair up

CSCvh21486

WLC reloads unexpectedly due to Task apfMsConnectionTask when MBUF debug is enabled

CSCvh21605

ME - wired clients drop-off shortly after being started from show client ap remote-lan

CSCvh21632

ME: Console freezes while transfer upload datatype signature

CSCvh21812

Cisco 3802 AP - Apple Broken Antenna Detection feature - XML support

CSCvh21942

8.7: Cisco WLC reloads unexpectedly during FW upgrade on 2 Floor Beacons with task: dx_sync_task

CSCvh21953

Cisco Aironet 1560, 1800, 2800 and 3800 Series Access Point Denial of Service Vulnerability

CSCvh23344

Cisco Controller reloads unexpectedly on taskname emweb @ewaFormSubmit_route_list

CSCvh23473

Cisco 1572 AP shows incorrect regulatory power level for Qatar domain

CSCvh23785

AireOS WLC: Multiple wireless clients failing the broadcast Key refresh (M5).

CSCvh25039

SNMP causes unexpected reloads

CSCvh25368

Cisco Controller memory leak on CDP

CSCvh27557

Cisco 1562 AP limited to 54 Mbps in 2.4-GHz backhaul

CSCvh27570

cLSiIdrClusterAffectedChannels OID returning unexpected values

CSCvh28229

Incorrect count for cLApWlanStatsOnlineUserNum when SSID is changed

CSCvh28506

Cisco 3504 controller cannot use USB for file transfer

CSCvh30447

MAP changes its statically assigned non-backhaul channel after it rejoins RAP

CSCvh30872

Decrypt errors on Cisco 1532 AP

CSCvh31233

AP fails to resend data on getting 401 error from Cisco DNA

CSCvh32561

Cisco 3700 AP reloads unexpectedly due to 'Per-Second Jobs' on 8.3.134.57

CSCvh32590

Cisco 1852 AP: Observed a radio core on loading the image, 5G @0x0099B20C,

CSCvh32971

Management through Wireless Not Working

CSCvh33064

Config logging traceinfo setting not restored correctly

CSCvh47521

Cisco IOS AP shows decrypt failed messages on driver debug

CSCvh48916

Cisco 1815I should consume power draw mentioned in the datasheet

CSCvh49623

Cisco Controller reloads unexpectedly with XML parse error during boot up

CSCvh50132

AP Sensor: PSK password being display in plain text test config

CSCvh50166

Cisco 2802e model without DART connector being considered as RRF candidate and assigned 5 GHz role

CSCvh50446

8.7: Hyperlocation destination IP missing from AP fast path

CSCvh51835

WGB client not getting IP address from the VLAN returned as AAA override

CSCvh51873

WLC reloads unexpectedly on Task Name: emWeb due to DATACORRUPTION-DATAINCONSISTENCY

CSCvh51936

Cisco 3504 controller flooding with emc1403 0-007c: Read failure of status register error msg

CSCvh52101

L1 list is not generated when AP moved from Monitor mode to Client serving mode

CSCvh52237

8.7:Dropping ADD_MOBILE due to mismatch in client radio/vap id slot id: 0 client_assoc_id: 1 vapid:

CSCvh53814

Cisco Wave 2 AP in Flex LS: IPv6 RA dropped with high level of multicast on wired interface

CSCvh54235

Cisco 3800 AP FW stopped working on Radio 0

CSCvh54459

Cisco AP console display logs 'DTX DUMP'

CSCvh55157

Cisco Controller reuses Acct-Session-Id when Client changes WLANs

CSCvh57198

Wired Cisco 1800 AP after Cisco DNA image refresh requires resetting from console

CSCvh57945

Cisco 3500, 5520 Controller reloads unexpectedly with sim_task on 8.7.1.107

CSCvh58148

Cisco Wave 2 APs uses invalid CAPWAP-Data keep-alive source port

CSCvh58266

WLC reloads unexpectedly on Task Name: ccxL2RoamTask 0x162ad5d l2roamGetRrmNeighborList+77

CSCvh58401

Address security issues in older curl and libxml libraries

CSCvh58467

Kernel Panic with PC at skb_release_data+0xe0/0x230

CSCvh58486

WLC reloads unexpectedly on Task Name: emWeb osapiMsgQueueDetailClear+42/usmDbMsgQueueDetailClear+27

CSCvh58917

Cisco WLC MAC authentication web redirected URL is broken

CSCvh59834

ME : Cannot change the role of XOR radio from Auto to Manual on AP2802E without DART

CSCvh60627

Cisco 3504 WLC reloads unexpectedly with taskname 'osapiReaper'

CSCvh60970

WLC reloads unexpectedly on Task Name:emWeb osapiMutexDumpAllLocked+890 after timezone setting of AP

CSCvh61107

GUI : EAP-TLS not working on Cisco 1815, 1562 AP models

CSCvh61355

WLC need remove WGB behind wired client after WGB changes to worst uplink

CSCvh61939

Cisco 1562 MAP is not forwarding BPDUs sent by the RAP when using Ethernet bridging

CSCvh62112

1832, 1852 APs reload unexpectedly due to memory leak in 4k slab with Spectrum Intelligence enabled

CSCvh62827

Wireless client cannot communicate each other with dynamic VLAN

CSCvh63417

d0: *** sensord died (src/dspm_main.c:1662/0) - slot 0 ***

CSCvh63454

Cisco 1261 AP standalone unexpectedly reloads on 8.3MR3 escalation image

CSCvh64065

Cisco 3800, 2800 AP: Beacons stuck because VAP is disabled

CSCvh65876

Cisco Wireless LAN Controller Software GUI Privilege Escalation Vulnerability

CSCvh66002

AP sniffer does not capture traffic when enabled for the first time on a channel

CSCvh66610

Cisco 3800,4800 APs unstable after upgrading to 8.7.1.115-vmalloc: allocation failure -FIQ/NMI reset

CSCvh66793

AP 1815W - continuously logs: missing case for op class XXX in ieee80211_mbo_operating_class_to_chan

CSCvh67548

Cisco 1600AP sending de-auth frame with reason code 7 to Random MAC Address XX:XX:00:00:00:00

CSCvh67549

Cisco 8540 WLC Data Plane reloads unexpectedly on __udp_input

CSCvh67590

WLC delay packets due to high DP packet buffers in use

CSCvh67738

Observed Traceback and FP0.05:(36)Pkt Ptr Unaligned, WQE-080000000037e6e00 on WLC HA while reset

CSCvh70051

Cisco 3800 AP DFS CAC failures on repeated channel changes/radar injection

CSCvh70067

WLC 8.7 not sending SPI keys, when added to CMX with HL enabled.

CSCvh72613

Cisco AP reloads unexpectedly when running show controller d1 atf cfs client

CSCvh72803

AP stops working during sh tech collection command that includes show CAPWAP client config

CSCvh72867

Radio reset with transmitter seems to have stopped

CSCvh73146

Cisco Controller reloads unexpectedly due to clientTroubleShootingTask 8.3.133.0

CSCvh73674

Cisco 1562 MAP not sending Air Quality reports to WLC

CSCvh73821

Cisco WLC reloads unexpectedly on sh run-config

CSCvh74663

IOS AP unexpectedly reloads during show CAPWAP client config using SSH

CSCvh77575

ATF monitor mode config for AP group is not reflecting on GUI

CSCvh77719

External MDNS resolution fails with WLC 'link local bridging' enabled

CSCvh78106

Cisco 2800,3800 AP on 8.7 code hangs for an hour with radio UP followed by silent reload

CSCvh78149

Cisco 1815 AP idle clients are not removed after 24 hrs

CSCvh78884

Cisco AP reloads unexpectedly on NBAR timer tick task

CSCvh79344

WLC is returning values for 'cLSiIdrDeviceSignature' OID with a length greater than 32 bytes

CSCvh79699

8.7:Task Name: spamApTask4 cSendConfigurationStatusResponse capwap_error_handler2

CSCvh79809

Sensor: poor on boarding connectivity with Cisco 1800S AP compared to Cisco 3800 AP

CSCvh81391

Cisco 2800, 3800 AP add CAPWAP ap-primed-join-timeout logic

CSCvh82606

LSC configurations are not persistent after certificate installation followed by system reboot

CSCvh82671

Clients are not able to load the Web-authentication login portal in Foreign-Anchor scenarios.

CSCvh83197

Cisco 1560 AP will create a loop when failing over to wireless and wired connection comes back

CSCvh83328

WLC reloads unexpectedly in loop while trying to download old config from TFTP

CSCvh83925

Webauth configuration is supported at testconfig level, rather than SSID level

CSCvh84101

ICMP reachability should not be performed by sensor tests other than host reachablity

CSCvh85082

Cisco 1562-I AP failed to decode discovery response and unexpectedly reloads

CSCvh85830

Cisco controller blocks client MAC authentication for wrong WLAN profile

CSCvh86834

802.11w client association data traffic drops after 802.11r roaming with PMF enabled or optional

CSCvh86845

Cisco Controller is unable to fetch CRL

CSCvh86970

ATF Mesh MIB Memory Leak observed during SNMPWALK from root

CSCvh89195

Unable to set 40MHz bandwidth for either channels 169 or 173 on Cisco 1542E AP

CSCvh89286

Cisco 2802,3802 APs: reloads with watchdog reset(wcpd) after mrvlfwd: Init of radio failed

CSCvh89438

Cisco 8510 WLC SNMP Traps for duplicate IP reported with IP address inversely

CSCvh91290

Cisco Wave 2 APs need to send XID broadcast on client association for FlexConnect local switching

CSCvh94458

Cisco Wave 1 APs last reload reason shows invalid image opcode

CSCvh94755

Client is able to ping management gateway before webauth login

CSCvh95762

Show traplog:Client Enhanced Traps Sent are not included in Number of Traps Since Last Reset

CSCvh96132

Cisco 8.5.110.0 release has many channel changes on XOR 5GHz

CSCvh96192

Cannot enable VLAN Support on AP 1562

CSCvh96895

Cisco 2800,3800,1560 APs: Perform duplicate check of assoc-req in clients with seq number as 0

CSCvh96956

Cisco 2800 AP cannot convert CAPWAP DSCP to 802.11e UP value correctly

CSCvh97469

Cisco Controller reloads unexpectedly with show run-config at commandConfig80211aSpectrumIntfDevList

CSCvh97739

Cisco 2800,3800 APs devshell to trace conversion

CSCvh97977

WLC Local Policy - Client Local Profiling assigns wrong Interface to Client

CSCvh98439

Cisco Controller stopped working while executing config client deauthenticate mac-addr command

CSCvh98496

Fan failure errors seen after upgrade to 8.3.133.10 release

CSCvh99287

Cisco OEAP drops wired client traffic after N+1 failover

CSCvi00786

IPsec stale entry observed with syslog

CSCvi01147

LSC cert keysize not retain after upload/download config

CSCvi01675

New Mobility with 3650MA and 5520 Anchor - Guest users cannot reach DG on 8.3.x

CSCvi01918

Cisco 3702 AP: RRM stall - RF neighbor list empty on both WLC and AP on 5GHz

CSCvi02072

Cisco Wave 2 APs: ETSI 5G adaptive Wi-Fi compliance fix

CSCvi02980

Cisco Controller becomes inaccessible with client rate limiting

CSCvi03114

Cisco 1852 Series APs reloads unexpectedly due to kernel panic

CSCvi04088

Ascom and Cisco 8821 phones on Cisco 3802 AP unable to make calls

CSCvi05095

Cisco 1040 AP in FlexConnect mode: radio reset with '%SOAP_BUF-2'

CSCvi06528

VLAN priority tag inside the EoGRE packet set to non-zero when 802.1p set to none

CSCvi06629

Not able to config the host name to 24 characters

CSCvi07460

WLC is incorrectly returning '5' for snmpwalk on bsnMobileStationApMode OID

CSCvi07565

Cisco 3800AP: Client EAP auth not working with wireless devices which sends certificate in fragments

CSCvi07609

Cisco 5520 WLC experiences fatal dataplane reloads unexpectedly at broffu_fp_dapi_cmd.c:4588

CSCvi08398

Cisco 5500 Controller reloads unexpectedly while adding LSC Dev cert multiple times [GUI or CLI]

CSCvi09025

Msglog flooded 'The Socket send operation has failed on the socket descriptor rmgrPhyMgrSock'

CSCvi09095

Radio Reset Tx Jammed seen on both 8.3 and 8.5

CSCvi09153

Cisco Wave 1 APs radio reset due FST14 FW: cmd=0x31 seq=6 due to mcast stuck in radio

CSCvi09424

Layer 3 Roam fails back to L2 Anchor with MAC Filtering MAB

CSCvi11287

Cisco 2800 AP consistently reboots around 1 second after joining to the WLC

CSCvi11609

DNS snooping not working for URL ACL after upgrade to 8.5 release

CSCvi11611

ME - 3802AP had FIQ/NMI reset during rate limiting test

CSCvi12046

FlexConnect AP WLAN-VLAN Mapped incorrectly on AP2800

CSCvi12726

UCAPL: login activity data is mismatched after telnet session

CSCvi13589

Locally generated webadmin certificate shows as 3rd party after upgrade on 8.3 code

CSCvi14638

Rogue BSSID containment count display incomplete

CSCvi14641

Cisco 2802, 3802 APs cannot connect with 100 Mbps LAN speed

CSCvi17079

Cisco Controller on 8.7 code reloads unexpectedly when accessing CMX AP groups over GUI

CSCvi17380

TxFSM stuck on Radio 0 with TCQVerify patch.

CSCvi17786

EoGRE client does not receive IP and stays in DHCP_REQ

CSCvi19706

Cisco 602 AP flapping when 2.4GHz and 5GHz radio are disabled

CSCvi20869

Cisco 1260,3500, 1550 Series APs: heavy packet loss in UDP downstream on 5GHz

CSCvi22594

Cisco DNAC: Adding new WLC successful or existing devices show that inventory poll fails with SNMP issue

CSCvi23698

Cisco 1560 AP on FlexConnect local-sw+802.1x+NAC:-ping traffic not going from client side

CSCvi25420

Cisco Wave 2 APs always send RTS at 6 data rate when data rate is supported

CSCvi25532

Standby 8540 WLC-reloads unexpectedly with rmgrMain due to IPC timeout

CSCvi25724

Cisco IOS APs unexpectedly reloads due to bad CPQ on 8.5 release code

CSCvi27226

Cisco 3802 AP: Radio core - receive path hang - RX-RING-STUCK

CSCvi29775

Cisco 8510 controller experiences DP0 CORE 9 Dataplane crash and reloads unexpectedly

CSCvi30627

Config missing after WLC failover

CSCvi30899

WLC 8.5 - AP fails to join the WLC when QA country code is used (-E AP)

CSCvi30993

Lost neighbor AP field on WLC GUI - NEIGHBOR AND ROGUE APS

CSCvi31343

Cisco WLC HA pair continues to reload unexpectedly due to system crash on broffu_SocketReceive

CSCvi32951

Cisco Wave 2 APs go offchannel if scan deferral value > 255 msec.

CSCvi33105

ODU sensor issue: WSA process disappeared after edit/delete/create of tests

CSCvi33984

HA pair does not sync VLAN support configuration for Cisco Mesh APs

CSCvi34440

Secondary Cisco 3504 WLC reloads unexpectedly in a loop

CSCvi36032

Missing AVC records on JSON data export from WLC 8.5 in FEW or Flex mode

CSCvi37522

Primary Cisco 5500 WLC on 8.5.124.22 reloads unexpectedly while joining AP due to 'Switchdrvr exited'

CSCvi38017

Standby WLC goes into a reboot loop after the software upgrade

CSCvi42526

Cisco Mesh 1562AP: AP will not go into bridge mode for I domain

CSCvi42919

Cisco 702w AP - Radio resets with ath_ACIF_radio_dead message

CSCvi42929

Sensor: webauth test failing in 1800 platform due to EOF occurred in violation of protocol

CSCvi43963

AP1562D to AP1562D bridge does not transmit fragmented traffic on 8.5.120.0

CSCvi45088

Cisco 2800, 3800 APs: adjust NDP pkt transmission power level

CSCvi45149

No RSSI/SNR info displayed with show client detail

CSCvi46306

Cisco 8510, 8540 controller on 8.5.124.27: Observed a traceback on booting up the image

CSCvi48427

'Enable DHCP Option 82 - VPN select' setting is lost after WLC reload

CSCvi49059

[FALL WLC BUNDLE] NO CVE Cisco Wireless LAN Controller Privilege Escalation Vulnerability

CSCvi49114

Cisco 3700 AP: memory allocation issue on IOS AP

CSCvi49126

RSN IE validation fails in M2 (802.11r session timeout) after reassociation causing deauth code 17

CSCvi49590

Bad phase calibration values in Triggerfish EEPROM

CSCvi50929

Cisco 3504 WLC reloads unexpectedly on 8.6.101 release

CSCvi51372

Client unable to reach RUN state on anchor WLC with 802.1x + ISE NAC

CSCvi51536

Access Point is not sending TCP fragments over the air

CSCvi51858

WLC not sending proper VSA list at acct-stop when client moves to another SSID

CSCvi53601

New Mobility Anchor Controller unexpectedly reboots with Task Name: mcListen

CSCvi54067

Cisco Wave 2 APs do not clear client statistics after device removed from client's database

CSCvi56046

Cisco 1560 RAP after reboot will lose the VLAN support configuration.

CSCvi56738

IW3702 on auto-bridge mode not preserving channel width more than 20MHz

CSCvi57043

WLC: WLC hang suddenly without crash file, osapiReaper accessing file that does not exist

CSCvi57169

SDA-Wireless AAA Override VNID ID is lost when roaming from one AP Group to another

CSCvi57213

Cisco 1832 AP unexpectedly reloads with 'PC is at __napi_complete+0x28/0x60'

CSCvi57232

CAP1815w-specific VLAN override RLAN fails, SSID FlexConnect VLAN takes precedence after AP reboot

CSCvi59432

Creation time of Local Net User set to Jan 1 00:00:00 1970

CSCvi61401

WLC remote access failing after upgrade

CSCvi65222

dot11 arp-cache does not work if BVI VLAN and client VLAN are different

CSCvi67365

Cisco 1850,3800AP: WPA_supplicant process reloads unexpectedly when used by WSA feature

CSCvi67565

TrustSec: AP picks wrong SXP Node ID

CSCvi69201

Line config wlan wifidirect xconnect-not-allow wlan-id manually entered in config backup is rejected

CSCvi70783

Wireless Service Assurance WSA: Cisco DNA Assurance certificate is not updated on WLC

CSCvi72800

Polaris COS-APs not correctly marking traffic when set/match policies and using multiple class-maps

CSCvi73013

Cisco Wave 1 AP deauthenticating client due to idle timeout

CSCvi73402

Cisco 1810W AP not giving IPs to cell phones using WPA/TKIP protocol

CSCvi74683

AIR-CT3504 mGig showing FCS errors incrementing

CSCvi78286

WLC Dashboard does not display the correct values for client throughput

CSCvi78819

HA : config service statistics not synced after failover

CSCvi79851

CPU ACL not configured after upgrading to Cisco 8.5.120.0 release

CSCvi81204

Cisco 2800, 3800 APs MTU issue with Fabric enable network

CSCvi84511

Cisco 3800 AP with Wired1 (aux) LAN enabled - CDP-4-DUPLEX_MISMATCH messages constantly logged

CSCvi84843

Client filter matches WLAN SSID, not WLAN Profile or WLAN ID

CSCvi84849

Cisco 1852 series APs unexpectedly reloads due to Kernel Panic

CSCvi85464

AP specific configuration lost post AP reload; WLAN-ACL mappings and policies lost

CSCvi85834

New Mobility CAPWAP control keepalive should not plumb keys when receiving unencrypted responses

CSCvi86276

Cisco WLC reloads unexpectedly on emWeb due to too many HTTP buffers received

CSCvi86834

Mesh Ethernet bridging - wired client associated to MAP fails to pass traffic over tagged VLAN

CSCvi90766

Cisco AP with regulatory domain Morocco cannot join the Cisco WLC

CSCvi91017

The FlexConnect groups are missing in backup configuration file

CSCvi91285

Install mapping on radio backhaul for Wave 2 APs Flex+Bridge setting is not retained after reboot

CSCvi93045

Cisco 2800 AP CleanAir goes down (sensord died)

CSCvi96690

Cisco 2800 AP detects Intel Dual Band Wireless-AC 8260 as rogue client/AP

CSCvi97023

Cisco Wireless LAN Controller Cross-Site Scripting Vulnerability

CSCvi97282

Assigning a NetFlow monitor to the WLAN will internally enable AVC on WLC

CSCvi98357

Cisco AP1815I : reloads unexpectedly due to 'watchdog reset(sync_log)'

CSCvi98514

MAP Ethernet port comes up as TRUNK and Allowed VLAN 4095

CSCvj03021

After upgrade the AP VLAN Trunking config changed to Disabled state

CSCvj03161

IOS AP not reporting known interference with disabled WSSI module

CSCvj04401

Client remains stuck in DHCP-REQD state on Anchor side unless ISE NAC is disabled on the anchor side

CSCvj07190

Cisco 2800 AP not joining WLC if 'Enable NAT Address' feature is enabled

CSCvj07930

Cisco 3802, 2802 AP with DART connectors has a Tx power value of 0

CSCvj11251

Cisco 2802 AP not sending re-association response to Cisco 8821 phone

CSCvj11270

Watchdog reset out of memory on Cisco 3800 AP running 8.3.133.0 code

CSCvj11397

Cisco 3504 Controller - OpenDNS registration failure - Return 77

CSCvj13920

WLC system reloads unexpectedly due to task name RRM-MGR-2_4-GRP

CSCvj13958

Cisco Wave 2 3800,2800 APs sending beacon on wrong channels intermittently on 5GHz

CSCvj17181

Creating a webauth CSR cert on the WLC GUI does not allow spaces

CSCvj18004

8.5MR3 Interim AP cannot join with NAT address on management interface of controller

CSCvj25194

Clean up debug lisp map-server output for AP onboarding

CSCvj25768

Bridge mode Cisco Wave 2 Mesh APs bridging issues

CSCvj25842

Cisco 1815I AP: Kernel panic: PC is at vfs_read+0x14/0x134

CSCvj28658

Cisco 1810wAP kernel panic leads to unexpected reload on PC at ieee80211_node_authorize+0x90/0xb8

CSCvj29270

Flex AP's WLAN-VLAN mapping mismatch in multiple WLC scenarios

CSCvj30550

Cisco WLC reloads unexpectedly when configuring PSK Provisioning key

CSCvj32624

702 AP as WGB keeps being disconnected from the WLAN due to parent lost: Missed beacons

CSCvj32964

WGB is only allowing 8 MAC addresses pass traffic using 3802 AP [as CAPWAP AP and 3702 AP as WGB]

CSCvj33894

Add 'show advanced hyperlocation summary' to 'show run-config' and 'show tech'

CSCvj35883

Allow Cisco 2800, 3800 APs to be able to convert to sensor mode

CSCvj36633

Cisco IOS AP: fail to boot after upgrade due to file corruption

CSCvj36853

AP name corruption after upgrade

CSCvj36923

Cisco AP name mismatch with controller on join

CSCvj37393

Cisco Wave 2 APs not sending probe response when SSID is not broadcast

CSCvj38456

WLC is losing its EoGRE configuration after reboot

CSCvj39005

[SDA] Wireless Clients losing L2VNID override when performing Switchover on Cisco 5520 WLC

CSCvj41040

Cisco 1800 APs in Cisco FlexConnect mode, fail FT roam

CSCvj41853

Incorrect Tx power on AP3802P-Q on some channels

CSCvj44533

SSH CBC ciphers are present from 8.6 and onwards releases

CSCvj45550

Cisco 1800 AP is appearing again in unclaim list after PnP provision

CSCvj47445

Cisco WLC sending CAPWAP discovery response when it has no available licenses

CSCvj48364

Cisco Controller is generating client traps without a session-id

CSCvj50170

Client coming back within 10 seconds of cleanup time is stopping the DHCP timer on the WLC

CSCvj53743

Cisco 1572IC AP: Channels and Maximum Power Settings settings spreadsheet incorrect values for V02

CSCvj54432

Cisco WLC unexpectedly reloads on task Dot1x_NW_MsgTask_2

CSCvj61140

Having Sensor-Driven tests configured cause 3802I AP to intermittent unexpected reload

CSCvj62672

WLC sending wrong NAS ID when AAA override is enabled

CSCvj69146

CME reloads unexpectedly in a loop due to PMALLOC_DOUBLE_FREE (capwap_ac_sm.c)

CSCvj70569

Cisco 2800, 3800,4800 APs: Incorrect Tx power on power on till we configure Tx power using Cisco WLC

CSCvj72890

Cisco 5520 WLC reloads unexpectedly when RADIUS server returns invalid value in Airespace-ACL-Name

CSCvj76378

Local policy is not applied when foreign WLC is running 8.3.141.0

CSCvj77078

WLC unexpectedly reboots on Dot1x_NW_MsgTask_1

CSCvj79108

WSA-8.5- NAC restarted with signal 6 after few minutes of WSA enabled in scale setup

CSCvj80388

Flex-ACL on Wave 2 AP's denying host instead of subnet

CSCvj83460

Cisco OEAP: client not associating for local SSID for default DHCP

CSCvj95336

Cisco Wireless LAN Controller Software Information Disclosure Vulnerability

CSCvk02024

Cisco 1850 APs experiencing frequent and unexpected reloads due to memory corruption

CSCvk05150

OpenDNS profile keeps being mapped for client when the username changes

CSCvk05965

Cisco WLC in HA SSO: standby controller is in a reboot loop

CSCvk06178

Uplink BPDUs are not bridged

CSCvk09135

Cisco 5520 Controller reloads unexpectedly for emweb in 8.6.101.0 release

CSCvk15068

IOS APs, recovery logic for MD5 checksum failure on primary Image

CSCvk15165

Cisco Controller reloads unexpectedly after modifying SNMP trap controls via GUI

CSCvk20484

IPC timeout and tracebacks reported on HA pair running 8.5.131.0 (8.5MR3)

CSCvk25644

WLC HA standby reboots reaching maintenance mode due to missing NaServCaCert_p12.pem on Active

CSCvk26732

New Flash recovery logic

Communications, Services, and Additional Information

  • To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.

  • To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.

  • To submit a service request, visit Cisco Support.

  • To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco Marketplace.

  • To obtain general networking, training, and certification titles, visit Cisco Press.

  • To find warranty information for a specific product or product family, access Cisco Warranty Finder.

Cisco Bug Search Tool

Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software.