Este documento describe los pasos de configuración mínimos requeridos en el multiplexor de acceso a línea de suscriptor digital (DSLAM) Huawei MA5600 para permitir que la línea de suscriptor digital de velocidad de bits muy alta (VDSL) se forme en el equipo de las instalaciones del cliente (CPE) de Cisco.
Cisco recomienda cumplir estos requisitos antes de realizar esta configuración:
La información en este documento se basa en un router Cisco 887VA que actúa como CPE y un DSLAM Huwei 5600. Sin embargo, este documento no se limita a versiones específicas de software y hardware.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Este documento tiene como objetivo ayudar a los ingenieros a configurar Cisco CPE y un DSLAM Huawei en entornos adosados/de laboratorio y comprender los perfiles básicos en el extremo de la oficina central (CO) de DSL.
Complete estas secciones para configurar su equipo:
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 4
MA5600#config
MA5600(config)#vdsl line-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl line-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,G993.2)
> 2: Full rate(G992.1/3/5,T1.413,G993.2)
> 3: G.DMT (G992.1/3/5,G993.2)
> 4: G.HS (G992.1~5,G993.2)
> 5: ADSL (G.992.1~5,T1.413)
> 6: VDSL (G993.2)
> Please select (0~6) [1]:6 >>>>>>>>>>>>>>>>>> Selecting Transmission Mode as VDSL
> Bit swap downstream 1-disable 2-enable (1~2) [2]:1
> Bit swap upstream 1-disable 2-enable (1~2) [2]:1
> Please select the form of transmit rate adaptation downstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Please select the form of transmit rate adaptation upstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Will you set SNR margin parameters? (y/n) [n]:
> Will you set DPBO parameters? (y/n)[n]:
> Will you set UPBO parameters? (y/n)[n]:
> Will you set RFI notch configuration parameter? (y/n) [n]:
> Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
> Will you set mode-specific parameters? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 2
MA5600(config)#vdsl channel-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl channel-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]:2 >>>>>>>>>>>>>>>>>>>>>> PTM Mode
> Will you set the minimum impulse noise protection? (y/n) [n]:
> Will you set interleaving delay parameters? (y/n) [n]:
> Will you set parameters for rate? (y/n) [n]:
> Will you set rate thresholds? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------>
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
------------------------------------------------------------------------------
Total: 5
MA5600(config)#vdsl line-template add 61
Start adding template
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the template (y/n) [n]:y
> Please input template name:ZONE_TEST
> Please set the line-profile index (1~128) [1]:61 >>>>>>>>>>>>>>>>Line Profile
we added above
> Will you set channel configuration parameters? (y/n) [n]:y
> Please set the channel number (1~2) [1]:
> Channel1 configuration parameters:
> Please set the channel-profile index (1~128) [1]:61 >>>>>> Channel Profile
we added above
Add template 61 successfully
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
En este caso, el CPE se conectó al puerto 0 de la ranura 5 del DSLAM Huawei.
MA5600(config)#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1
-------------------------------------------------------------------------
0 H563ADGE Failed
1 H565ADBF Normal >>>>>>>>>ADBF - Here 'A' means that this card supports ADSL
2 ADG Failed
3 H569SHEB Failed
4
5 H565VDBD Normal >>>> >>>>VDBD - Here 'V' means that this card supports VDSL
6
7 H561SCU Standby_normal O2FM >>>>>>>>>>>>>>>>>>>>>> Processor Cards
8 H561SCU Active_normal O2GS O2GS >>>>>>>>>>>>> Processor Cards
9
10
11 H565VDBD Failed
12 H569SHEB Failed
13
14 H561SHEA Failed
15
-------------------------------------------------------------------------
MA5600(config)#interface vdsl 0/5 (Board/ slot)
Check the port status: Status is deactivated and currently assigned to
Line Template 1 (default)
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Deactivated Disable 1 1
-----------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#activate 0 template-index 61
>>>>>>>> We are already in board 0 slot 5, hence need to activate port 0 with
Line Template 61
MA5600(config-if-vdsl-0/5)#display port state 0
---------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activating Disable 61 1 >>>>>Check the status
---------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activated Disable 61 1 >>Status is activated
---------------------------------------------------------------
Utiliza esta sección para verificar su configuración.
La herramienta de interpretación de información de salida (disponible para clientes registrados únicamente) admite ciertos comandos show. Utilice la herramienta para ver una análisis de información de salida del comando show.
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
Para ello, debe estar en el modo de configuración de la interfaz del DSLAM.
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Activated Disable 61 1
-----------------------------------------------------------------
Ingrese el comando show controller vdsl 0 en el CPE para verificar el estado del controlador.
/snip
C887VA-M#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0x939B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FTX162580HZ 887VA-M 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0x939b
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 12a
TC Mode: PTM
Actualmente, no hay información específica de troubleshooting disponible para esta configuración.
Revisión | Fecha de publicación | Comentarios |
---|---|---|
1.0 |
01-Dec-2014 |
Versión inicial |