Risoluzione dei problemi ARP in SD-Access Fabric
Sommario
Introduzione
In questo documento viene descritto come risolvere i problemi relativi al protocollo ARP (Address Resolution Protocol) nell'infrastruttura SD-Access.
Prerequisiti
Requisiti
Cisco raccomanda la conoscenza dei seguenti argomenti:
- Inoltro IP (Internet Protocol)
- Locator/ID Separation Protocol (LISP)
- Protocollo ARP (Address Resolution Protocol)
Componenti usati
Le informazioni fornite in questo documento si basano sulle seguenti versioni software e hardware:
- C9000v su Cisco IOS® XE 17.10.1
- SDA 1.0 (non LISP PubSub)
Le informazioni discusse in questo documento fanno riferimento a dispositivi usati in uno specifico ambiente di emulazione. Su tutti i dispositivi menzionati nel documento la configurazione è stata ripristinata ai valori predefiniti. Se la rete è operativa, valutare attentamente eventuali conseguenze derivanti dall'uso dei comandi.
Il presente documento può essere utilizzato anche per le seguenti versioni hardware e software:
- C9200
- C9300
- C9400
- C9500
- C9600
- Cisco IOS® XE 16.12 e versioni successive
Topologia
In questo esercizio:
- 10.47.1.10 e 10.47.1.11 sono Bordi ripartiti
- 10.47.1.12 e 10.47.1.13 sono nodi Fabric Edge
- 10.47.4.2 e 10.47.4.3 sono endpoint nell'infrastruttura SDA e si trovano nella stessa VLAN/subnet e nella stessa VN (red_vn)
In questo documento sono illustrati due casi di utilizzo principali:
- Risoluzione ARP compresa tra 10.47.4.2 e 10.47.4.3 su percorso unicast
- Risoluzione ARP compresa tra 10.47.4.2 e 10.47.4.3 attraverso un percorso di allagamento
Stato iniziale percorso unicast
All'interno di SDA, ci sono due metodi principali per la risoluzione ARP all'interno del fabric. Ciò che viene definito come percorso unicast indica che non esiste una configurazione di ARP Flooding di layer 2 (L2) o la mancanza di "Flood Arp and" (ID istanza) configurata in LISP L2 (IID) che corrisponde alla VLAN in questione. Oltre a questa avvertenza, per ottenere il percorso ARP unicast, non vi è alcuna configurazione di "IP local proxy ARP" o nessuna presenza di un pool di soli layer 3.
Se vengono soddisfatte queste condizioni, continuare con la sezione sulla risoluzione dei problemi e si presume che entrambi gli endpoint (10.47.4.2 e 10.47.4.3) possano raggiungere i rispettivi gateway predefiniti presenti sugli switch Fabric Edge con nome 10.47.4.1
Edge-1#ping vrf red_vn 10.47.4.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.47.4.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 257/292/344 ms
Edge-2#ping vrf red_vn 10.47.4.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.47.4.3, timeout is 2 seconds: !!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 221/321/566 ms
Verificare quindi che ogni nodo Fabric Edge disponga del proprio endpoint all'interno di IP Device-Tracking (IPDT), del database LISP L2, del database L2 Address Resolution (AR) e del database L3.
Edge-1:
Per verificare l'endpoint in IPDT, utilizzare il comando show device-tracking database interface <interface connecting to endpoint>
Edge-1#show device-tracking database interface g1/0/3
portDB has 2 entries for interface Gi1/0/3, 2 dynamic
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
Network Layer Address Link Layer Address Interface vlan prlvl age state Time left
DH4 10.47.4.2 5254.0019.93e9 Gi1/0/3 1026 0024 15s REACHABLE 228 s try 0(6374 s)
Per verificare l'endpoint nel database LISP L2, usare il comando show lisp eid-table vlan <id vlan> ethernet database <indirizzo mac>usare l'indirizzo VLAN e MAC del comando precedente
Edge-1#show lisp eid-table vlan 1026 ethernet database 5254.0019.93e9 LISP ETR MAC Mapping Database for LISP 0 EID-table Vlan 1026 (IID 8190), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 2 5254.0019.93e9/48, dynamic-eid Auto-L2-group-8190, inherited from default locator-set rloc_222e1707-175d-4019-a783-060404f8bc2f Uptime: 3w5d, Last-change: 3w5d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.12 10/10 cfg-intf site-self, reachable <-- Edge-1's RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w3d Yes 0 10.47.1.11 3w5d Yes 0
Per verificare il database L2 AR, usare il comando show lisp eid-table vlan <vlan-id> ethernet database address-resolution <mac address>
Edge-1#show lisp eid-table vlan 1026 ethernet database address-resolution 5254.0019.93e9 LISP ETR Address Resolution for LISP 0 EID-table Vlan 1026 (IID 8190) (*) -> entry being deleted Hardware Address L3 InstID Host Address 5254.0019.93e9 4099 10.47.4.2/32 <-- Endpoint MAC address, LISP L3 IID, and IPv4 address, respectively
Per verificare il database LISP L3, usare il comando show lisp instance-id <ID3> ipv4 database <indirizzo IPv4>/subnet mask usare l'ID LISP L3 del comando precedente
Edge-1#show lisp instance-id 4099 ipv4 database 10.47.4.2/32 LISP ETR IPv4 Mapping Database for LISP 0 EID-table vrf red_vn (IID 4099), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 1 10.47.4.2/32, dynamic-eid red-IPV4, inherited from default locator-set rloc_222e1707-175d-4019-a783-060404f8bc2f Uptime: 3w5d, Last-change: 3w5d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.12 10/10 cfg-intf site-self, reachable <-- Edge-1's own RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w0d Yes 0 10.47.1.11 1w0d Yes 0
Edge-2
Per verificare l'endpoint in IPDT, utilizzare il comando show device-tracking database interface <interface connecting to local endpoint>
Edge-2#show device-tracking database interface g1/0/3
portDB has 3 entries for interface Gi1/0/3, 3 dynamic
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
Network Layer Address Link Layer Address Interface vlan prlvl age state Time left
DH4 10.47.4.3 5254.001e.ad00 Gi1/0/3 1026 0024 122s REACHABLE 124 s try 0(5810 s)
Per verificare l'endpoint nel database LISP L2, usare il comando show lisp eid-table vlan <id vlan> ethernet database <indirizzo mac> e usare l'indirizzo VLAN e MAC del comando precedente
Edge-2#show lisp eid-table vlan 1026 ethernet database 5254.001e.ad00 LISP ETR MAC Mapping Database for LISP 0 EID-table Vlan 1026 (IID 8190), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 2 5254.001e.ad00/48, dynamic-eid Auto-L2-group-8190, inherited from default locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51 Uptime: 3w5d, Last-change: 3w5d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.13 10/10 cfg-intf site-self, reachable <-- Edge-2's RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w2d Yes 0 10.47.1.11 1w2d Yes 0
Per verificare il database L2 AR, usare il comando show lisp eid-table vlan <vlan-id> ethernet database address-resolution <mac address>
Edge-2#show lisp eid-table vlan 1026 ethernet database address-resolution 5254.001e.ad00 LISP ETR Address Resolution for LISP 0 EID-table Vlan 1026 (IID 8190) (*) -> entry being deleted Hardware Address L3 InstID Host Address 5254.001e.ad00 4099 10.47.4.3/32 <-- Endpoint MAC address, LISP L3 IID, and IPv4 address, respectively
Per verificare il database LISP L3, usare il comando show lisp instance-id <ID3> ipv4 database <indirizzo IPv4>/subnet mask usare l'ID LISP L3 del comando precedente
Edge-2#show lisp instance-id 4099 ipv4 database 10.47.4.3/32 LISP ETR IPv4 Mapping Database for LISP 0 EID-table vrf ed_vn (IID 4099), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 2 10.47.4.3/32, dynamic-eid red-IPV4, inherited from default locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51 Uptime: 1w0d, Last-change: 1w0d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.13 10/10 cfg-intf site-self, reachable <-- Edge-2, RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w0d Yes 0 10.47.1.11 1w0d Yes 0
Bordi collocati:
Idealmente, entrambi gli endpoint vengono registrati da una prospettiva L2 LISP, L2 AR e L3 ai piani di controllo fabric (Border-1 e Border-2). Per derivare l'ID LISP L2, controllare un nodo Fabric Edge e usare il comando show vlan id <vlan id>
Edge-1#show vlan id 1026 VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1026 red active L2LI0:8190, Gi1/0/3 <-- L2 LISP IID VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1026 enet 101026 1500 - - - - - 0 0 Remote SPAN VLAN ---------------- Disabled Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------
Utilizzare l'ID L2 nel comando show lisp instance-id <ID2> ethernet server per verificare il server dal punto di vista dell'ID L2
Border-1#show lisp instance-id 8190 ethernet server
LISP Site Registration Information
* = Some locators are down or unreachable
# = Some registrations are sourced by reliable transport
Site Name Last Up Who Last Inst EID Prefix
Register Registered ID
site_uci never no -- 8190 any-mac
1w3d yes# 10.47.1.12:21038 8190 5254.0019.93e9/48 <-- RLOC of the FE node, EID prefix that was registered
1w2d yes# 10.47.1.13:16056 8190 5254.001e.ad00/48 <-- RLOC of the FE node, EID prefix that was registered
Per verificare il server L2 AR, utilizzare il comando show lisp instance-id <ID2> ethernet server address-resolution
Border-1#show lisp instance-id 8190 ethernet server address-resolution
Address-resolution data for router lisp 0 instance-id 8190
L3 InstID Host Address Hardware Address
4099 10.47.4.2/32 5254.0019.93e9 <-- L3 LISP IID, Endpoint IPv4 Address, MAC Address, respectively
4099 10.47.4.3/32 5254.001e.ad00 <-- L3 LISP IID, Endpoint IPv4 Address, MAC Address, respectively
Per verificare il server L3, utilizzare il comando show lisp instance-id <ID3> ipv4 server
Border-1#show lisp instance-id 4099 ipv4 server
LISP Site Registration Information
* = Some locators are down or unreachable
# = Some registrations are sourced by reliable transport
Site Name Last Up Who Last Inst EID Prefix
Register Registered ID
site_uci never no -- 4099 0.0.0.0/0
6d01h yes# 10.47.1.11:22876 4099 8.8.8.8/32
1w0d yes# 10.47.1.10:21610 4099 10.47.2.4/30
1w0d yes# 10.47.1.11:22876 4099 10.47.2.12/30
never no -- 4099 10.47.4.0/24
1w0d yes# 10.47.1.12:21038 4099 10.47.4.2/32
1w0d yes# 10.47.1.13:16056 4099 10.47.4.3/32
1w0d yes# 10.47.1.11:22876 4099 10.47.6.0/24
1w0d yes# 10.47.1.11:22876 4099 10.47.7.0/24
1w0d yes# 10.47.1.11:22876 4099 10.47.9.8/29
never no -- 4099 10.47.10.0/24
1w0d yes# 10.47.1.13:16056 4099 10.47.10.2/32
I Control Plane dispongono di una breve cronologia degli eventi di registrazione per le voci L3, L2 e AR, che può essere utile per la risoluzione dei problemi dei client in roaming o di un possibile loop in cui i client vengono registrati in modo imprevisto da diversi Fabric Edge in un tempo molto breve.
Border-1#show lisp instance-id 8190 ethernet server resolution registration-history | include Timestamp|10.47.4.2|10.47.4.3
Timestamp (UTC) Instance Proto Roam WLC Source
*Oct 9 19:14:39.183 8190 TCP No No 10.47.1.12
+*10.47.4.2/32 / 5254.0019.93e9 <-- Last registered at Oct 9 19:14:39
*Oct 9 19:14:41.183 8190 TCP No No 10.47.1.13
+*10.47.4.3/32 / 5254.001e.ad00 <-- Last registered at OCt 9 19:14:31
Flusso di lavoro di alto livello richiesta ARP percorso unicast
Verifica richiesta ARP percorso unicast
L'endpoint a cui appartiene l'indirizzo IP 10.47.4.2 invia una richiesta ARP di trasmissione, con conferma tramite un EPC (Embedded Packet Capture) sul perimetro 1
Edge-1 (10.47.1.12)
Edge-1#monitor capture 1 interface g1/0/3 in match any
Edge-1#monitor capture 1 start
Edge-1#monitor capture 1 stop
Capture statistics collected at software:
Capture duration - 39 seconds
Packets received - 21
Packets dropped - 0
Packets oversized - 0
Number of Bytes dropped at asic not collected
Capture buffer will exists till exported or cleared
Stopped capture point : 1
Edge-1#show monitor capture 1 buffer brief
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
1 0.000000 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.
Edge-1#show monitor capture 1 buffer detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 1: 60 bytes on wire (480 bits), 60 bytes captured (480 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 19, 2023 23:43:31.893095000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1697759011.893095000 seconds
[Time delta from previous captured frame: 0.000000000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 0.000000000 seconds]
Frame Number: 1
Frame Length: 60 bytes (480 bits)
Capture Length: 60 bytes (480 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:arp]
Ethernet II, Src: 52:54:00:19:93:e9 (52:54:00:19:93:e9), Dst: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
Destination: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
Address: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast)
Source: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
Address: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: ARP (0x0806)
Padding: 000000000000000000000000000000000000
Address Resolution Protocol (request)
Hardware type: Ethernet (1)
Protocol type: IPv4 (0x0800)
Hardware size: 6
Protocol size: 4
Opcode: request (1)
Sender MAC address: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
Sender IP address: 10.47.4.2
Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00)
Target IP address: 10.47.4.3
La richiesta ARP viene inoltrata alla CPU per un'ulteriore elaborazione. Utilizzate FED Punject Capture per ottenere ulteriori informazioni.
Edge-1#debug platform software fed switch active punt packet-capture set-filter “arp" Edge-1#debug platform software fed switch active punt packet-capture start Edge-1#debug platform software fed switch active punt packet-capture stop Edge-1#show platform software fed switch active punt packet-capture brief Punt packet capturing: disabled. Buffer wrapping: disabled Total captured so far: 8 packets. Capture capacity : 4096 packets Capture filter : "arp" ------ Punt Packet Number: 1, Timestamp: 2023/10/19 23:55:03.552 ------ interface : physical: GigabitEthernet1/0/3[if-id: 0x0000000b], pal: GigabitEthernet1/0/3 [if-id: 0x0000000b] <-- Physical interface the ARP Request was received from metadata : cause: 109 [snoop packets], sub-cause: 1, q-no: 16, linktype: MCP_LINK_TYPE_IP [1] <-- Punted for cause snoop packets to CPU queue 16 ether hdr : dest mac: ffff.ffff.ffff, src mac: 5254.0019.93e9 ether hdr : ethertype: 0x0806 (ARP)
Per verificare la coda CPU 16, usare il comando show platform software fed switch active punt cpuq 16
Edge-1#show platform software fed switch active punt cpuq 16 Punt CPU Q Statistics =========================================== CPU Q Id : 16 CPU Q Name : CPU_Q_PROTO_SNOOPING Packets received from ASIC : 49054 Send to IOSd total attempts : 49054 <-- Same number as received from ASIC
Send to IOSd failed count : 0 <-- No failures
Se la coda di snooping delle copie non presenta cadute nel policer della CPU (coda 16), usare il comando show platform hardware fed switch active qos queue stats internal cpu policer
Edge-1#show platform hardware fed switch active qos queue stats internal cpu policer | include QId|Proto QId PlcIdx Queue Name Enabled Rate Rate Drop(Bytes) Drop(Frames) 16 12 Proto Snooping No 2000 2000 0 0 <-- No drops
Successivamente, la richiesta ARP puntata viene elaborata dal servizio Punt. Per visualizzare questo comportamento, usare il comando debug, debug platform software infrastructure
Edge-1#debug platform software infrastructure punt
*Oct 20 00:07:01.509: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 20 00:07:01.509: Punt: IP proto src 147.233.10.47, dst 4.2.0.0, from table 0, intf Gi1/0/3, encap ARPA, size 60, cause snoop packets(L3) <-- The IP address is obscured, but it is 10.47.4.2 *Oct 20 00:07:01.509: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 20 00:07:01.509: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
Dopo aver elaborato il pacchetto, il servizio Punt consegna il pacchetto al processo Proto Snoop e Proto ARP Snoop. In questo modo viene creata una voce nella tabella di snooping ARP e il pacchetto viene inviato a Device-Tracking/SISF. A tale scopo, eseguire il debug dell'arp e del file fhs della piattaforma di debug
Edge-1#debug arp
Edge-1#debug platform fhs all
*Oct 20 00:12:06.908: ARP packet received from ARP snooper(Gi1/0/3 10.47.4.2 (5254.0019.93e9) VLAN:1026)
Utilizzare il comando show platform arpsnooping client <indirizzo MAC> per verificare cosa succede alla richiesta ARP
Edge-1#show platform arpsnooping client 5254.0019.93e9 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.0019.93E9: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------ 2023/10/24 14:37:15.045 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PSISF_PRE:PSP_BRNEUTRAL 2023/10/24 14:37:15.045 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 14:37:15.045 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:BD_DPIDX_TO_FWDPLANE
Durante l'elaborazione del pacchetto, IPDT/SISF verifica il contenuto della richiesta ARP e crea una voce temporanea in attesa della risoluzione tramite LISP.
Edge-1#show device-tracking messages detailed 255 | i 5254.0019.93e9 [Tue Oct 24 14:37:12.000] VLAN 1026, From Gi1/0/3 seclvl [guard], MAC 5254.0019.93e9: ARP::REQ, [Tue Oct 24 14:37:13.000] VLAN 1026, From Gi1/0/3 seclvl [guard], MAC 5254.0019.93e9: ARP::REQ,
Se si utilizza il comando debug device-tracking, si osserverà che nella voce device-tracking è presente una voce che punta verso 0000.000.00fd. Ciò significa che l'host dietro Gi1/0/3 sta eseguendo una query per un host che non è ancora stato risolto, si trova in uno stato transitorio (o permanente nel caso in cui stia eseguendo una query per un host che non esiste, ciò non è necessariamente un problema)
Edge-1#debug device-tracking Device-tracking - General debugging is on *Oct 24 14:55:02.967: SISF[POL]: vlan 1026 matches vlan list on policy IPDT_POLICY for target Gi1/0/3 *Oct 24 14:55:02.967: SISF[POL]: Found matching policy IPDT_POLICY for feature Device-tracking on Gi1/0/3
*Oct 24 14:55:02.967:SISF[GLN]: Checking if ARP ownership can be taken by device-tracking
*Oct 24 14:55:02.967:SISF[GLN]: Not an ARP reply, do not take over
*Oct 24 14:55:02.967:SISF[POL]: Found matching policy LISP-AR-RELAY-VLAN for feature Address Resolution Relay on vlan 1026 *Oct 24 14:55:02.967: SISF[MAC]: Creating new MAC entry for 0000.0000.00fd on interface if none exists *Oct 24 14:55:02.967: SISF[MAC]: Number of MAC entries in MAC-CREATING state incremented to 1 *Oct 24 14:55:02.968: SISF[BT ]: Attaching 0000.0000.00fd entry in MacAdrDB for 10.47.4.3 *Oct 24 14:55:02.968: SISF[GLN]: Binding entry event 1 for 10.47.4.3
La SISF attiva la risoluzione ARP utilizzando il LISP a causa della policy LISP-AR-RELAY-VLAN, dopo che i processi LISP Control-Plane possono assumere il controllo.
Edge-1#debug lisp control-plane all Edge-1#debug l2lisp all *Oct 24 15:10:27.677: LISP Client 'SISF client': SISF request to resolve 10.47.4.3 in Vlan 1026.
Edge-1 invia una richiesta di mappa LISP per risolvere l'indirizzo MAC 10.47.4.3 tramite i Control Plane LISP
Edge-1#debug lisp control-plane all Edge-1#debug l2lisp all *Oct 24 15:10:27.681: LISP[REMT ]-0: Map Request: Delay is over for IID 8190 EID 10.47.4.3/32, requester 'AR'. *Oct 24 15:10:27.681: LISP[REMT ]-0 IID 8190: Schedule processing of Map-Requests from 'remote EID prefix' in IPv4. *Oct 24 15:10:27.681: LISP[REMT ]-0: Map Request: Sending request for IID 8190 EID 10.47.4.3/32, requester 'AR'.
Un'acquisizione EPC (Embedded Packet Capture) bidirezionale eseguita sulla CPU (control-plane) di Edge-1 mostra la richiesta ARP in entrata e la successiva richiesta di mappa LISP
Edge-1#monitor capture 1 control-plane both match any Edge-1#monitor capture 1 start Started capture point : 1 Edge-1#monitor capture 1 stop Edge-1#show monitor capture 1 buffer display-filter "arp.dst.proto_ipv4==10.47.4.3 or lisp" Starting the packet display ........ Press Ctrl + Shift + 6 to exit 60 10.110293 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 61 10.111714 10.47.4.3 -> 10.47.4.3 LISP 114 Encapsulated Map-Request for Unknown LCAF Type (53)/32
È possibile ottenere una visualizzazione più dettagliata di LISP Map-Request
Edge-1#show monitor capture 1 buffer display-filter "frame.number==61" detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 61: 114 bytes on wire (912 bits), 114 bytes captured (912 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 24, 2023 15:20:08.948469000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698160808.948469000 seconds
[Time delta from previous captured frame: 0.001421000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 10.111714000 seconds]
Frame Number: 61
Frame Length: 114 bytes (912 bits)
Capture Length: 114 bytes (912 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:lisp:ip:udp:lisp]
Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) <-- Ignore the SMAC/DMAC this is done up at the CPU, not final MAC addresses
Destination: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.10 <-- Edge-1 RLOC and one of the collocated border RLOC, respectively
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 100
Identification: 0x599c (22940)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x4ab9 [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.12
Destination: 10.47.1.10
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 80
Checksum: 0x6393 [unverified]
[Checksum Status: Unverified]
[Stream index: 0]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Locator/ID Separation Protocol
1000 .... .... .... .... .... = Type: Encapsulated Control Message (8)
.... 0... .... .... .... .... .... .... = S bit (LISP-SEC capable): Not set
.... .0.. .... .... .... .... .... .... = D bit (DDT-originated): Not set
.... ..00 0000 0000 0000 0000 0000 0000 = Reserved bits: 0x0000000
Internet Protocol Version 4, Src: 10.47.4.3, Dst: 10.47.4.3 <-- MAP Request to resolve the MAC address tied to 10.47.4.3
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 68
Identification: 0x599b (22939)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x44ea [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.4.3
Destination: 10.47.4.3
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 48
Checksum: 0x9622 [unverified]
[Checksum Status: Unverified]
[Stream index: 1]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Locator/ID Separation Protocol
0001 .... .... .... .... .... = Type: Map-Request (1)
.... 0000 00.. .... .... .... = Flags: 0x00
.... 0... .... .... .... .... = A bit (Authoritative): Not set
.... .0.. .... .... .... .... = M bit (Map-Reply present): Not set
.... ..0. .... .... .... .... = P bit (Probe): Not set
.... ...0 .... .... .... .... = S bit (Solicit-Map-Request): Not set
.... .... 0... .... .... .... = p bit (Proxy ITR): Not set
.... .... .0.. .... .... .... = s bit (SMR-invoked): Not set
.... .... ..00 0000 000. .... = Reserved bits: 0x000
.... .... .... .... ...0 0000 = ITR-RLOC Count: 0
Record Count: 1
Nonce: 0xcffee30fb39a05b7
Source EID AFI: Reserved (0)
Source EID: not set
ITR-RLOC 1: 10.47.1.12
ITR-RLOC AFI: IPv4 (1)
ITR-RLOC Address: 10.47.1.12
Map-Request Record 1: Unknown LCAF Type (53)/32
Reserved: 0x00
Prefix Length: 32
Prefix AFI: LISP Canonical Address Format (LCAF) (16387)
Prefix: Unknown LCAF Type (53)
LCAF: Unknown (53)
LCAF Header: 00003520000a
Reserved bits: 0x00
Flags: 0x00
Type: Unknown (53)
Reserved bits: 0x20
Length: 10
[Expert Info (Error/Protocol): LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05]
[LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05]
[Severity level: Error]
[Group: Protocol]
Bordo/i ripartito/i (10.47.1.10 e 10.47.1.11)
Successivamente, il Control-Plane LISP risponde a Edge-1 con una risposta di mappa LISP. Questa condizione può essere rilevata nei debug e nell'EPC della CPU.
Border-2#show monitor capture 1 buffer display-filter lisp Starting the packet display ........ Press Ctrl + Shift + 6 to exit 113 12.767420 10.47.4.3 -> 10.47.4.3 LISP 114 Encapsulated Map-Request for Unknown LCAF Type (53)/32 114 12.774428 10.47.1.11 -> 10.47.1.12 LISP 96 Map-Reply for Unknown LCAF Type (53)/32
Analizzando i pacchetti in dettaglio, possiamo vedere la richiesta di mappa LISP e la successiva risposta di mappa LISP
Border-2#show monitor capture 1 buffer display-filter frame.number==113 detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 113: 114 bytes on wire (912 bits), 114 bytes captured (912 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 24, 2023 15:41:06.566253000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698162066.566253000 seconds
[Time delta from previous captured frame: 0.013424000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 12.767420000 seconds]
Frame Number: 113
Frame Length: 114 bytes (912 bits)
Capture Length: 114 bytes (912 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:lisp:ip:udp:lisp]
Ethernet II, Src: 52:54:00:04:84:a3 (52:54:00:04:84:a3), Dst: 52:54:00:1c:7d:e0 (52:54:00:1c:7d:e0) <-- True MAC addresses
Destination: 52:54:00:1c:7d:e0 (52:54:00:1c:7d:e0)
Address: 52:54:00:1c:7d:e0 (52:54:00:1c:7d:e0)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 52:54:00:04:84:a3 (52:54:00:04:84:a3)
Address: 52:54:00:04:84:a3 (52:54:00:04:84:a3)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.11 <-- Edge-1 RLOC and Border-2 RLOC, respectively
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 100
Identification: 0x5e19 (24089)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x463b [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.12
Destination: 10.47.1.11
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 80
Checksum: 0x6392 [unverified]
[Checksum Status: Unverified]
[Stream index: 1]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Locator/ID Separation Protocol
1000 .... .... .... .... .... = Type: Encapsulated Control Message (8)
.... 0... .... .... .... .... .... .... = S bit (LISP-SEC capable): Not set
.... .0.. .... .... .... .... .... .... = D bit (DDT-originated): Not set
.... ..00 0000 0000 0000 0000 0000 0000 = Reserved bits: 0x0000000
Internet Protocol Version 4, Src: 10.47.4.3, Dst: 10.47.4.3 <-- LISP MAP Request for 10.47.4.3
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 68
Identification: 0x5e18 (24088)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x406d [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.4.3
Destination: 10.47.4.3
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 48
Checksum: 0xe9a8 [unverified]
[Checksum Status: Unverified]
[Stream index: 2]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Locator/ID Separation Protocol
0001 .... .... .... .... .... = Type: Map-Request (1)
.... 0000 00.. .... .... .... = Flags: 0x00
.... 0... .... .... .... .... = A bit (Authoritative): Not set
.... .0.. .... .... .... .... = M bit (Map-Reply present): Not set
.... ..0. .... .... .... .... = P bit (Probe): Not set
.... ...0 .... .... .... .... = S bit (Solicit-Map-Request): Not set
.... .... 0... .... .... .... = p bit (Proxy ITR): Not set
.... .... .0.. .... .... .... = s bit (SMR-invoked): Not set
.... .... ..00 0000 000. .... = Reserved bits: 0x000
.... .... .... .... ...0 0000 = ITR-RLOC Count: 0
Record Count: 1
Nonce: 0x50c5f2b60b41ca1c
Source EID AFI: Reserved (0)
Source EID: not set
ITR-RLOC 1: 10.47.1.12
ITR-RLOC AFI: IPv4 (1)
ITR-RLOC Address: 10.47.1.12
Map-Request Record 1: Unknown LCAF Type (53)/32
Reserved: 0x00
Prefix Length: 32
Prefix AFI: LISP Canonical Address Format (LCAF) (16387)
Prefix: Unknown LCAF Type (53)
LCAF: Unknown (53)
LCAF Header: 00003520000a
Reserved bits: 0x00
Flags: 0x00
Type: Unknown (53)
Reserved bits: 0x20
Length: 10
[Expert Info (Error/Protocol): LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05]
[LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05]
[Severity level: Error]
[Group: Protocol]
Possiamo anche vedere la mappa LISP-Risposta che viene inviata indietro
Border-2#show monitor capture 1 buffer display-filter frame.number==114 detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 114: 96 bytes on wire (768 bits), 96 bytes captured (768 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 24, 2023 15:41:06.573261000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698162066.573261000 seconds
[Time delta from previous captured frame: 0.007008000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 12.774428000 seconds]
Frame Number: 114
Frame Length: 96 bytes (768 bits)
Capture Length: 96 bytes (768 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:lisp]
Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) <-- CPU Inject does not properly show MAC addresses
Destination: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.11, Dst: 10.47.1.12 <-- Border-2 RLOC and Edge-1 RLOC, respectively
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 82
Identification: 0xe231 (57905)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0xc234 [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.11
Destination: 10.47.1.12
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 62
Checksum: 0xe1d6 [unverified]
[Checksum Status: Unverified]
[Stream index: 1]
[Timestamps]
[Time since first frame: 0.007008000 seconds]
[Time since previous frame: 0.007008000 seconds]
Locator/ID Separation Protocol
0010 .... .... .... .... .... = Type: Map-Reply (2)
.... 0... .... .... .... .... = P bit (Probe): Not set
.... .0.. .... .... .... .... = E bit (Echo-Nonce locator reachability algorithm enabled): Not set
.... ..0. .... .... .... .... = S bit (LISP-SEC capable): Not set
.... ...0 0000 0000 0000 0000 = Reserved bits: 0x00000
Record Count: 1
Nonce: 0x50c5f2b60b41ca1c
Mapping Record 1, EID Prefix: Unknown LCAF Type (53)/32, TTL: 1440, Action: No-Action, Not Authoritative
Record TTL: 1440
Locator Count: 1
EID Mask Length: 32
000. .... .... .... = Action: No-Action (0)
...0 .... .... .... = Authoritative bit: Not set
.... .000 0000 0000 = Reserved: 0x000
0000 .... .... .... = Reserved: 0x0
.... 0000 0000 0000 = Mapping Version: 0
EID Prefix AFI: LISP Canonical Address Format (LCAF) (16387)
EID Prefix: Unknown LCAF Type (53)
LCAF: Unknown (53)
LCAF Header: 00003520000a
Reserved bits: 0x00
Flags: 0x00
Type: Unknown (53)
Reserved bits: 0x20
Length: 10
[Expert Info (Error/Protocol): LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05]
[LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05]
[Severity level: Error]
[Group: Protocol]
Locator Record 1, RLOC: 52:54:00:1e:ad:00, Unreachable, Priority/Weight: 1/100, Multicast Priority/Weight: 1/100
Priority: 1
Weight: 100
Multicast Priority: 1
Multicast Weight: 100
Flags: 0x0000
0000 0000 0000 0... = Reserved: 0x0000
.... .... .... .0.. = Local: Not set
.... .... .... ..0. = Probe: Not set
.... .... .... ...0 = Reachable: Not set
AFI: 802 (includes all 802 media plus Ethernet) (6)
Locator: 52:54:00:1e:ad:00
Border-2#debug lisp control-plane all All LISP control debugging is on at verbose level Border-2#debug l2lisp all All L2Lisp debugging is on *Oct 24 16:02:17.854: LISP[TRNSP]-0: Processing received Encap-Control(8) message on GigabitEthernet1/0/3 from 10.47.1.12:4342 to 10.47.1.11:4342. *Oct 24 16:02:17.854: LISP[TRNSP]-0: Processing received Map-Request(1) message on GigabitEthernet1/0/3 from 10.47.4.3:4342 to 10.47.4.3:4342. *Oct 24 16:02:17.855: LISP[MR ]-0: Received Map-Request with 1 records, first EID IID 8190 10.47.4.3/32, source EID UNSPEC, nonce 0x3847C91F-0xA966DDEA. *Oct 24 16:02:17.855: LISP[MR ]-0 IID 8190 Eth-ARP: MS EID 10.47.4.3/32: Sending proxy reply to 10.47.1.12.
Ora che Edge-1 ha ricevuto una Map-Reply LISP per la richiesta Address Resolution (AR) che indica che 10.47.4.3 è 5254.001e.ad00, Edge-1 genera un'altra Map-Request LISP per determinare la RLOC per l'indirizzo MAC dell'endpoint
Edge-1#debug lisp control-plane all
Edge-1#debug l2lisp all
*Oct 24 16:19:54.843: LISP[REMT ]-0: Received Map-Reply with nonce 0x37F890B9-0xAC60D2B9, 1 records.
*Oct 24 16:19:54.843: LISP[MS ]-0: This is a Address Resolution message.
*Oct 24 16:19:54.843: LISP[REMT ]-0: Map-Reply nonce matches pending request for IID 8190 EID 10.47.4.3/32, requester 'AR'.
*Oct 24 16:19:54.843: LISP[REMT ]-0: Processing Map-Reply mapping record for IID 8190 Eth-ARP 10.47.4.3/32 LCAF 53, ttl 1440, action none, not authoritative, 1 locator.
*Oct 24 16:19:54.843: LISP[REMT ]-0: 5254.001e.ad00 pri/wei/dID/mID/met/si_type/si_id/si_flg/afn_id=1/100/0/0/4294967295/none/0/UNSPEC/UNSPEC lpr.
*Oct 24 17:11:24.056: LISP[REMT ]-0 IID 8190: Schedule processing of Map-Requests from 'remote EID prefix' in IPv4. *Oct 24 17:11:24.056: LISP[REMT ]-0:
Map Request: Sending request for IID 8190 EID 5254.001e.ad00/48, requester 'remote EID prefix'.>
Il Control-Plane LISP riceve la Map-Request LISP, per l'indirizzo MAC 10.47.4.3, consulta la tabella del server Ethernet per l'ID L2 LISP 8190 e invia una Map-Reply LISP con il binding MAC-RLOC
Border-1#show monitor capture 1 buff display-filter lisp brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit
250 28.656076 0.0.0.0 -> 0.0.0.0 LISP 176 Encapsulated Map-Request for [8190] 52:54:00:1e:ad:00/48 251 28.658851 10.47.1.10 -> 10.47.1.12 LISP 96 Map-Reply for [8190] 52:54:00:1e:ad:00/48
Possiamo dare un'occhiata più da vicino al LISP Map-Request e Map-Reply
Border-1#show monitor capture 1 buffer display-filter frame.number==250 detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 250: 176 bytes on wire (1408 bits), 176 bytes captured (1408 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 24, 2023 17:37:11.647755000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698169031.647755000 seconds
[Time delta from previous captured frame: 0.315724000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 28.656076000 seconds]
Frame Number: 250
Frame Length: 176 bytes (1408 bits)
Capture Length: 176 bytes (1408 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:lisp:ip:udp:lisp]
Ethernet II, Src: 52:54:00:04:84:b1 (52:54:00:04:84:b1), Dst: 52:54:00:0a:42:f3 (52:54:00:0a:42:f3)
Destination: 52:54:00:0a:42:f3 (52:54:00:0a:42:f3)
Address: 52:54:00:0a:42:f3 (52:54:00:0a:42:f3)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 52:54:00:04:84:b1 (52:54:00:04:84:b1)
Address: 52:54:00:04:84:b1 (52:54:00:04:84:b1)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.10 <-- Edge-1 RLOC and Border-1 RLOC, respectively
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 162
Identification: 0x75e5 (30181)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x2e32 [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.12
Destination: 10.47.1.10
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 142
Checksum: 0x46f1 [unverified]
[Checksum Status: Unverified]
[Stream index: 4]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Locator/ID Separation Protocol
1000 .... .... .... .... .... = Type: Encapsulated Control Message (8)
.... 0... .... .... .... .... .... .... = S bit (LISP-SEC capable): Not set
.... .0.. .... .... .... .... .... .... = D bit (DDT-originated): Not set
.... ..00 0000 0000 0000 0000 0000 0000 = Reserved bits: 0x0000000
Internet Protocol Version 4, Src: 0.0.0.0, Dst: 0.0.0.0
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 130
Identification: 0x75e4 (30180)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x44c7 [validation disabled]
[Header checksum status: Unverified]
Source: 0.0.0.0
Destination: 0.0.0.0
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 110
Checksum: 0x18bb [unverified]
[Checksum Status: Unverified]
[Stream index: 5]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Locator/ID Separation Protocol
0001 .... .... .... .... .... = Type: Map-Request (1)
.... 0100 00.. .... .... .... = Flags: 0x10
.... 0... .... .... .... .... = A bit (Authoritative): Not set
.... .1.. .... .... .... .... = M bit (Map-Reply present): Set
.... ..0. .... .... .... .... = P bit (Probe): Not set
.... ...0 .... .... .... .... = S bit (Solicit-Map-Request): Not set
.... .... 0... .... .... .... = p bit (Proxy ITR): Not set
.... .... .0.. .... .... .... = s bit (SMR-invoked): Not set
.... .... ..00 0000 000. .... = Reserved bits: 0x000
.... .... .... .... ...0 0000 = ITR-RLOC Count: 0
Record Count: 1
Nonce: 0x86438e956066d3ca
Source EID AFI: LISP Canonical Address Format (LCAF) (16387)
Source EID: [8190] 00:00:0c:9f:f3:41
LCAF: Instance ID: 8190, Address: 00:00:0c:9f:f3:41
LCAF Header: 00000220000c
Reserved bits: 0x00
Flags: 0x00
Type: Instance ID (2)
Reserved bits: 0x20
Length: 12
Instance ID: 8190
Address AFI: 802 (includes all 802 media plus Ethernet) (6)
Address: 00:00:0c:9f:f3:41 (00:00:0c:9f:f3:41)
ITR-RLOC 1: 10.47.1.12
ITR-RLOC AFI: IPv4 (1)
ITR-RLOC Address: 10.47.1.12
Map-Request Record 1: [8190] 52:54:00:1e:ad:00/48 <-- Map-Request for this specific MAC address
Reserved: 0x00
Prefix Length: 48
Prefix AFI: LISP Canonical Address Format (LCAF) (16387)
Prefix: [8190] 52:54:00:1e:ad:00
LCAF: Instance ID: 8190, Address: 52:54:00:1e:ad:00
LCAF Header: 00000220000c
Reserved bits: 0x00
Flags: 0x00
Type: Instance ID (2)
Reserved bits: 0x20
Length: 12
Instance ID: 8190
Address AFI: 802 (includes all 802 media plus Ethernet) (6)
Address: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00)
Map-Reply Record
Mapping Record 1, EID Prefix: [8190] 00:00:0c:9f:f3:41/48, TTL: 1440, Action: No-Action, Authoritative
Record TTL: 1440
Locator Count: 1
EID Mask Length: 48
000. .... .... .... = Action: No-Action (0)
...1 .... .... .... = Authoritative bit: Set
.... .000 0000 0000 = Reserved: 0x000
0000 .... .... .... = Reserved: 0x0
.... 0000 0000 0000 = Mapping Version: 0
EID Prefix AFI: LISP Canonical Address Format (LCAF) (16387)
EID Prefix: [8190] 00:00:0c:9f:f3:41
LCAF: Instance ID: 8190, Address: 00:00:0c:9f:f3:41
LCAF Header: 00000220000c
Reserved bits: 0x00
Flags: 0x00
Type: Instance ID (2)
Reserved bits: 0x20
Length: 12
Instance ID: 8190
Address AFI: 802 (includes all 802 media plus Ethernet) (6)
Address: 00:00:0c:9f:f3:41 (00:00:0c:9f:f3:41)
Locator Record 1, Local RLOC: 10.47.1.12, Reachable, Priority/Weight: 10/10, Multicast Priority/Weight: 10/10
Priority: 10
Weight: 10
Multicast Priority: 10
Multicast Weight: 10
Flags: 0x0005
0000 0000 0000 0... = Reserved: 0x0000
.... .... .... .1.. = Local: Set
.... .... .... ..0. = Probe: Not set
.... .... .... ...1 = Reachable: Set
AFI: IPv4 (1)
Locator: 10.47.1.12
Border-1#show monitor capture 1 buffer display-filter frame.number==251 detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 251: 96 bytes on wire (768 bits), 96 bytes captured (768 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 24, 2023 17:37:11.650530000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698169031.650530000 seconds
[Time delta from previous captured frame: 0.002775000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 28.658851000 seconds]
Frame Number: 251
Frame Length: 96 bytes (768 bits)
Capture Length: 96 bytes (768 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:lisp]
Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00)
Destination: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.10, Dst: 10.47.1.12 <-- Border-1 RLOC, Edge-1 RLOC, respectively
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT)
1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 82
Identification: 0x12a9 (4777)
Flags: 0x0000
0... .... .... .... = Reserved bit: Not set
.0.. .... .... .... = Don't fragment: Not set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0x91be [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.10
Destination: 10.47.1.12
User Datagram Protocol, Src Port: 4342, Dst Port: 4342
Source Port: 4342
Destination Port: 4342
Length: 62
Checksum: 0xd63e [unverified]
[Checksum Status: Unverified]
[Stream index: 4]
[Timestamps]
[Time since first frame: 0.002775000 seconds]
[Time since previous frame: 0.002775000 seconds]
Locator/ID Separation Protocol
0010 .... .... .... .... .... = Type: Map-Reply (2)
.... 0... .... .... .... .... = P bit (Probe): Not set
.... .0.. .... .... .... .... = E bit (Echo-Nonce locator reachability algorithm enabled): Not set
.... ..0. .... .... .... .... = S bit (LISP-SEC capable): Not set
.... ...0 0000 0000 0000 0000 = Reserved bits: 0x00000
Record Count: 1
Nonce: 0x86438e956066d3ca
Mapping Record 1, EID Prefix: [8190] 52:54:00:1e:ad:00/48, TTL: 1440, Action: No-Action, Not Authoritative
Record TTL: 1440
Locator Count: 1
EID Mask Length: 48
000. .... .... .... = Action: No-Action (0)
...0 .... .... .... = Authoritative bit: Not set
.... .000 0000 0000 = Reserved: 0x000
0000 .... .... .... = Reserved: 0x0
.... 0000 0000 0000 = Mapping Version: 0
EID Prefix AFI: LISP Canonical Address Format (LCAF) (16387)
EID Prefix: [8190] 52:54:00:1e:ad:00
LCAF: Instance ID: 8190, Address: 52:54:00:1e:ad:00
LCAF Header: 00000220000c
Reserved bits: 0x00
Flags: 0x00
Type: Instance ID (2)
Reserved bits: 0x20
Length: 12
Instance ID: 8190
Address AFI: 802 (includes all 802 media plus Ethernet) (6)
Address: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00)
Locator Record 1, RLOC: 10.47.1.13, Reachable, Priority/Weight: 10/10, Multicast Priority/Weight: 10/10
Priority: 10
Weight: 10
Multicast Priority: 10
Multicast Weight: 10
Flags: 0x0001
0000 0000 0000 0... = Reserved: 0x0000
.... .... .... .0.. = Local: Not set
.... .... .... ..0. = Probe: Not set
.... .... .... ...1 = Reachable: Set
AFI: IPv4 (1)
Locator: 10.47.1.13 <-- This RLOC owns the MAC address
Border-1#debug lisp control-plane all
Border-1#debug l2lisp all
*Oct 24 18:03:00.361: LISP[TRNSP]-0: Processing received Map-Request(1) message on GigabitEthernet1/0/3 from 0.0.0.0:4342 to 0.0.0.0:4342. *Oct 24 18:03:00.361: LISP[MR ]-0: Received Map-Request with 1 records, first EID IID 8190 5254.001e.ad00/48, source EID 0000.0c9f.f341, nonce 0xAD90C521-0x348A478D. *Oct 24 18:03:00.361: LISP[MR ]-0 IID 8190 MAC: MS EID 5254.001e.ad00/48: Sending proxy reply to 10.47.1.12.
Edge-1 riceve la mappa LISP-Risposta da Border-1
Edge-1#debug lisp control-plane all
Edge-1#debug l2lisp all
*Oct 24 17:11:24.558: LISP[TRNSP]-0: Processing received Map-Reply(2) message on GigabitEthernet1/0/1 from 10.47.1.10:4342 to 10.47.1.12:4342. *Oct 24 17:11:24.558: LISP[REMT ]-0: Received Map-Reply with nonce 0x38A78BA8-0xC378149D, 1 records. *Oct 24 17:11:24.558: LISP[REMT ]-0: Map-Reply nonce matches pending request for IID 8190 EID 5254.001e.ad00/48, requester 'remote EID prefix'. *Oct 24 17:11:24.558: LISP[REMT ]-0: Processing Map-Reply mapping record for IID 8190 MAC 5254.001e.ad00/48 LCAF 2, ttl 1440, action none, not authoritative, 1 locator. *Oct 24 17:11:24.559: LISP[REMT ]-0: 10.47.1.13 pri/wei/dID/mID/met/si_type/si_id/si_flg/afn_id=10/10/0/0/4294967295/none/0/UNSPEC/UNSPEC lpR.
L'intera richiesta ARP tramite lo scambio LISP/SISF può essere visualizzata su Edge-1 tramite EPC CPU
Edge-1#show monitor capture 1 buffer display-filter "arp.dst.proto_ipv4==10.47.4.3 or lisp" Starting the packet display ........ Press Ctrl + Shift + 6 to exit
120 18.415474 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 <-- Broadcast ARP Request punted up to the CPU 121 18.416092 10.47.4.3 -> 10.47.4.3 LISP 114 Encapsulated Map-Request for Unknown LCAF Type (53)/32 <-- LISP Map-Request to obtain the MAC address of 10.47.4.3 135 19.598041 10.47.1.11 -> 10.47.1.12 LISP 96 Map-Reply for Unknown LCAF Type (53)/32 <-- LISP Map-Reply providing the MAC address of 10.47.4.3 136 19.613072 0.0.0.0 -> 0.0.0.0 LISP 176 Encapsulated Map-Request for [8190] 52:54:00:1e:ad:00/48 <-- LISP Map-Request to obtain the RLOC for MAC address 5254.001e.ad00 138 20.119722 10.47.1.10 -> 10.47.1.12 LISP 96 Map-Reply for [8190] 52:54:00:1e:ad:00/48 <-- LISP Map-Reply for the RLOC that owns MAC address 5254.001e.ad00 143 20.477618 52:54:00:19:93:e9 -> 52:54:00:1e:ad:00 ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 <-- Unicast ARP Request injected down from the CPU
Una volta che il control-plane sul bordo 1 è convergente, sono disponibili una voce map-cache e una voce remota SISF (RMT)
Edge-1#show lisp instance-id 8190 ethernet map-cache 5254.001e.ad00
LISP MAC Mapping Cache for LISP 0 EID-table Vlan 1026 (IID 8190), 1 entries
5254.001e.ad00/48, uptime: 00:06:26, expires: 23:53:34, via map-reply, complete
Sources: map-reply
State: complete, last modified: 00:06:26, map-source: 10.47.1.13
Active, Packets out: 11(0 bytes), counters are not accurate (~ 00:00:00 ago)
Encapsulating dynamic-EID traffic
Locator Uptime State Pri/Wgt Encap-IID
10.47.1.13 00:06:26 up 10/10 -
Last up-down state change: 00:06:26, state change count: 1
Last route reachability change: 2w0d, state change count: 1
Last priority / weight change: never/never
RLOC-probing loc-status algorithm:
Last RLOC-probe sent: 00:06:25 (rtt 1104ms)
Edge-1#show device-tracking database address 10.47.4.3
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
Network Layer Address Link Layer Address Interface vlan prlvl age state Time left
RMT 10.47.4.3 5254.001e.ad00 L2LI0 1026 0005 7mn STALE try 0 731 s
Successivamente, la richiesta ARP unicast viene iniettata giù dalla CPU. Tenere presente che non è possibile acquisire i pacchetti incapsulati dalla CPU in direzione di uscita con EPC su interfacce fisiche, SPAN (Switchport Port Analyzer) o EPC in entrata sul nodo Fabric Edge ricevente per confermare la ricezione della richiesta ARP unicast incapsulata VXLAN
Edge-2 (10.47.1.13)
Verificare innanzitutto che l'interfaccia LISP o tunnel sia elencata nell'output dell'ID VLAN per la VLAN 1026
Edge-2#show vlan id 1026 VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1026 red active L2LI0:8190, Gi1/0/3 <-- L2 LISP IID is associated VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1026 enet 101026 1500 - - - - - 0 0 Remote SPAN VLAN ---------------- Disabled Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------
Ora, un EPC in entrata sul perimetro 2 mostra la risposta ARP incapsulata della VXLAN ricevuta. Poiché la richiesta ARP unicast è incapsulata in VXLAN, è possibile usare un ACL IP per confrontare la richiesta RLOC Edge-1 con l'invio della richiesta RLOC Edge-2 (rispettivamente da 10.47.1.12 a 10.47.1.13) per contribuire a filtrare il traffico.
Edge-2(config)#ip access-list extended tac Edge-2(config-ext-nacl)#permit ip host 10.47.1.12 host 10.47.1.13
Edge-2#monitor capture 1 interface g1/0/1 in access-list tac Edge-2#monitor capture 1 interface g1/0/2 in access-list tac Edge-2#monitor capture 1 start Started capture point : 1 Edge-2#monitor capture 1 stop Capture statistics collected at software: Capture duration - 20 seconds Packets received - 10 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1
Edge-2#show monitor capture 1 buffer brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit 1 0.000000 52:54:00:19:93:e9 -> 52:54:00:1e:ad:00 ARP 110 Who has 10.47.4.3? Tell 10.47.4.2
Dopo un'ispezione più attenta di questa richiesta ARP, è possibile verificare la presenza di incapsulamento VXLAN, intestazione UDP e altre intestazioni, in quanto un frame ARP è piccolo, normalmente 60 byte.
Edge-2#show monitor capture 1 buffer display-filter frame.number==1 detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 1: 110 bytes on wire (880 bits), 110 bytes captured (880 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 24, 2023 18:57:34.642468000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698173854.642468000 seconds
[Time delta from previous captured frame: 0.000000000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 0.000000000 seconds]
Frame Number: 1
Frame Length: 110 bytes (880 bits)
Capture Length: 110 bytes (880 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:vxlan:eth:ethertype:arp]
Ethernet II, Src: 52:54:00:0a:42:11 (52:54:00:0a:42:11), Dst: 52:54:00:17:fe:65 (52:54:00:17:fe:65)
Destination: 52:54:00:17:fe:65 (52:54:00:17:fe:65)
Address: 52:54:00:17:fe:65 (52:54:00:17:fe:65)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 52:54:00:0a:42:11 (52:54:00:0a:42:11)
Address: 52:54:00:0a:42:11 (52:54:00:0a:42:11)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.13 <-- Edge-1 RLOC and Edge-2 RLOC, respectively
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0x00 (DSCP: CS0, ECN: Not-ECT)
0000 00.. = Differentiated Services Codepoint: Default (0)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 96
Identification: 0x798a (31114)
Flags: 0x4000, Don't fragment
0... .... .... .... = Reserved bit: Not set
.1.. .... .... .... = Don't fragment: Set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 253
Protocol: UDP (17)
Header checksum: 0xed8b [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.12
Destination: 10.47.1.13
User Datagram Protocol, Src Port: 65354, Dst Port: 4789
Source Port: 65354
Destination Port: 4789
Length: 76
[Checksum: [missing]]
[Checksum Status: Not present]
[Stream index: 0]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Virtual eXtensible Local Area Network
Flags: 0x8800, GBP Extension, VXLAN Network ID (VNI)
1... .... .... .... = GBP Extension: Defined
.... .... .0.. .... = Don't Learn: False
.... 1... .... .... = VXLAN Network ID (VNI): True
.... .... .... 0... = Policy Applied: False
.000 .000 0.00 .000 = Reserved(R): 0x0000
Group Policy ID: 0
VXLAN Network Identifier (VNI): 8190 <-- LISP L2 IID
Reserved: 0
Ethernet II, Src: 52:54:00:19:93:e9 (52:54:00:19:93:e9), Dst: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00) <-- True source and destination endpoint MAC address
Destination: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00)
Address: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
Address: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: ARP (0x0806)
Trailer: 000000000000000000000000000000000000
Address Resolution Protocol (request)
Hardware type: Ethernet (1)
Protocol type: IPv4 (0x0800)
Hardware size: 6
Protocol size: 4
Opcode: request (1)
Sender MAC address: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
Sender IP address: 10.47.4.2
Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00)
Target IP address: 10.47.4.3
Edge-2 disattiva l'incapsulamento VXLAN e invia la richiesta ARP unicast alla CPU per un'ulteriore elaborazione. Questa condizione può essere rilevata tramite una cattura di FED Punject.
Edge-2#debug platform software fed switch active punt packet-capture start Punt packet capturing started. Edge-2#debug platform software fed switch active punt packet-capture stop Punt packet capturing stopped. Captured 21 packet(s) Edge-2#show platform software fed sw active punt packet-capture display-filter "arp" brief Punt packet capturing: disabled. Buffer wrapping: disabled Total captured so far: 21 packets. Capture capacity : 4096 packets ------ Punt Packet Number: 6, Timestamp: 2023/10/24 19:14:32.930 ------ interface : physical: [if-id: 0x00000000], pal: L2LISP0 [if-id: 0x00000017] metadata : cause: 109 [snoop packets], sub-cause: 1, q-no: 16, linktype: MCP_LINK_TYPE_IP [1] ether hdr : dest mac: 5254.001e.ad00, src mac: 5254.0019.93e9 ether hdr : ethertype: 0x0806 (ARP)
La richiesta ARP viene inviata al processo ARP Snooper.
Edge-2#debug platform software infrastructure punt
*Oct 24 19:18:38.916: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 24 19:18:38.916: Punt: IP proto src 147.233.10.47, dst 4.2.0.0, from table 0, intf L2LI0, encap LISP, size 60, cause snoop packets(L3) <-- You can see the 10.47.4.2 *Oct 24 19:18:38.916: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 24 19:18:38.916: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
Poiché questa richiesta ARP proviene da un'interfaccia L2 LISP/Tunnel, Edge-2 non apprende mai 10.47.4.2 come endpoint locale di un EID dinamico in LISP
Edge-2#show platform arpsnooping client 5254.0019.93e9 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.0019.93E9: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------ 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PLATF_DAI:RECEIVED INPUT 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PLATF_DAI:RECEIVED_TUNNEL 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PLATF_DAI:SHUNTED
A questo punto, la richiesta ARP viene iniettata dalla CPU nella VLAN 1026, in particolare nella VLAN 1/0/3, a cui è collegata la versione 10.47.4.3.
Edge-2#show mac address-table address 5254.001e.ad00
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
1026 5254.001e.ad00 DYNAMIC Gi1/0/3
Total Mac Addresses for this criterion: 1
Edge-2#show platform arpsnooping client 5254.001e.ad00
PLAT_DAI : Platform DAI shim
FWDPLANE : Dataplane forwarding
BRIDGE : Packet to be bridged
ARPSN : Arp Snooping
Packet Trace for client MAC 5254.001E.AD00:
Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action
----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI
2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:BD_DPIDX_TO_FWDPLANE
Flusso di lavoro di alto livello risposta ARP percorso unicast
Verifica risposta ARP percorso unicast
Edge-2 (10.47.1.13)
L'endpoint proprietario della versione 10.47.4.3 risponde con una risposta ARP unicast, la risposta ARP viene puntata fino alla CPU a causa della presenza di IPDT. La verifica iniziale viene eseguita tramite EPC sull'interfaccia rivolta verso l'endpoint.
Edge-2#show monitor capture 1 buffer display-filter arp
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
2 88.712035 52:54:00:1e:ad:00 -> 00:00:0c:9f:f3:41 ARP 60 10.47.4.3 is at 52:54:00:1e:ad:00
Verificare quindi l'azione punt con un punject FED
Edge-2#debug platform software fed sw active punt packet-capture start Punt packet capturing started. Edge-2#debug platform software fed sw active punt packet-capture stop Punt packet capturing stopped. Captured 22 packet(s) Edge-2#show platform software fed sw active punt packet-capture display-filter "arp" brief Punt packet capturing: disabled. Buffer wrapping: disabled Total captured so far: 22 packets. Capture capacity : 4096 packets ------ Punt Packet Number: 6, Timestamp: 2023/10/24 20:32:35.634 ------ interface : physical: [if-id: 0x00000000], pal: L2LISP0 [if-id: 0x00000017] metadata : cause: 109 [snoop packets], sub-cause: 1, q-no: 16, linktype: MCP_LINK_TYPE_IP [1] <-- Punted for Snoop Packets to CPU queue 16 ether hdr : dest mac: 5254.001e.ad00, src mac: 5254.0019.93e9 ether hdr : ethertype: 0x0806 (ARP)
Successivamente, la risposta ARP viene passata a ARP Snooper and Device-Tracking
Edge-2#debug platform software infrastructure punt
*Oct 24 19:18:39.101: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 24 19:18:39.101: Punt: IP proto src 173.0.10.47, dst 4.3.82.84, from table 0, intf Gi1/0/3, encap ARPA, size 60, cause snoop packets(L3) <-- 10.47.4.3 is obscured *Oct 24 19:18:39.101: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 24 19:18:39.101: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
Edge-2#debug platform fhs Edge-2#debug platform fhs all ARP packet received from ARP snooper(Gi1/0/3 10.47.4.3 (5254.001e.ad00) VLAN:10
Edge-2#debug device-tracking
*Oct 24 20:42:22.554: SISF[CLA]: Interest on target vlan 1026 *Oct 24 20:42:22.554: SISF[CLA]: feature Device-tracking *Oct 24 20:42:22.554: SISF[CLA]: feature Address Resolution Relay
*Oct 24 20:42:22.555: SISF[SWI]: Gi1/0/3 vlan 1026 Feature_0 Device-tracking priority 128 *Oct 24 20:42:22.555: SISF[SWI]: Gi1/0/3 vlan 1026 Feature_1 Address Resolution Relay priority 81 *Oct 24 20:42:22.555: SISF[PRS]: ARP-REPLY target set to 10.47.4.2 *Oct 24 20:42:22.556: SISF[SWI]: Gi1/0/3 vlan 1026 Feature Device-tracking rc: OK *Oct 24 20:42:22.556: SISF[ARR]: Gi1/0/3 vlan 1026 Receive a msg in AR *Oct 24 20:42:22.557: SISF[ARR]: Gi1/0/3 vlan 1026 Not ARP Request or NS, return OK *Oct 24 20:42:22.557: SISF[SWI]: Gi1/0/3 vlan 1026 Feature Address Resolution Relay rc: OK *Oct 24 20:42:22.557: SISF[SWI]: Gi1/0/3 vlan 1026 Features execution OK
Poiché la risposta ARP punta già a un indirizzo MAC di destinazione reale (non come un segnaposto visto temporaneamente su Edge-1), Edge-2 può attivare una richiesta di mappa LISP per risolvere l'associazione RLOC-MAC.
Edge-2#debug lisp control-plane all
Edge-2#debug l2lisp all
*Oct 24 20:47:34.400: LISP[REMT ]-0 IID 8190: Schedule processing of Map-Requests from 'remote EID prefix' in IPv4. *Oct 24 20:47:34.401: LISP[REMT ]-0: Map Request: Sending request for IID 8190 EID 5254.0019.93e9/48, requester 'remote EID prefix'. *Oct 24 20:47:35.166: LISP[TRNSP]-0: Processing received Map-Reply(2) message on GigabitEthernet1/0/1 from 10.47.1.11:4342 to 10.47.1.13:4342. *Oct 24 20:47:35.166: LISP[REMT ]-0: Received Map-Reply with nonce 0x5879579E-0xCAFC0AA5, 1 records. *Oct 24 20:47:35.166: LISP[REMT ]-0: Processing Map-Reply mapping record for IID 8190 MAC 5254.0019.93e9/48 LCAF 2, ttl 1440, action none, not authoritative, 1 locator. *Oct 24 20:47:35.166: LISP[REMT ]-0: 10.47.1.12 pri/wei/dID/mID/met/si_type/si_id/si_flg/afn_id=10/10/0/0/4294967295/none/0/UNSPEC/UNSPEC lpR.
Utilizzare il comando show lisp instance-id <L2 ID> ethernet map-cache <indirizzo MAC destinazione> per verificare a quale RLOC deve essere inviata questa risposta ARP con incapsulamento VXLAN
Edge-2#show lisp instance-id 8190 ethernet map-cache 5254.0019.93e9
LISP MAC Mapping Cache for LISP 0 EID-table Vlan 1026 (IID 8190), 1 entries
5254.0019.93e9/48, uptime: 00:03:45, expires: 23:56:15, via map-reply, complete
Sources: map-reply
State: complete, last modified: 00:03:45, map-source: 10.47.1.12
Active, Packets out: 6(0 bytes), counters are not accurate (~ 00:00:59 ago)
Encapsulating dynamic-EID traffic
Locator Uptime State Pri/Wgt Encap-IID
10.47.1.12 00:03:45 up 10/10 -
Last up-down state change: 00:03:45, state change count: 1
Last route reachability change: 2w0d, state change count: 1
Last priority / weight change: never/never
RLOC-probing loc-status algorithm:
Last RLOC-probe sent: 00:03:45 (rtt 861ms)
Dopo la risoluzione LISP, la risposta ARP può essere iniettata dalla CPU verso 10.47.1.12 RLOC nella parte inferiore
Edge-2#show ip cef 10.47.1.12 10.47.1.12/32 nexthop 10.47.1.2 GigabitEthernet1/0/2 nexthop 10.47.1.6 GigabitEthernet1/0/1
L'intero flusso può essere visualizzato sulla CPU Edge-2 tramite EPC. La differenza tra una risposta ARP e una richiesta ARP consiste nel fatto che in questo flusso non è presente alcuna risoluzione AR LISP.
Edge-2#show monitor capture 1 buffer display-filter "arp.src.proto_ipv4==10.47.4.3 or lisp" Starting the packet display ........ Press Ctrl + Shift + 6 to exit 62 9.355185 52:54:00:1e:ad:00 -> 52:54:00:19:93:e9 ARP 60 10.47.4.3 is at 52:54:00:1e:ad:00 <-- ARP Reply punted up to the CPU 63 9.355486 0.0.0.0 -> 0.0.0.0 LISP 176 Encapsulated Map-Request for [8190] 52:54:00:19:93:e9/48 <-- LISP Map-Request to resolve RLOC-MAC association 88 12.058412 10.47.1.10 -> 10.47.1.13 LISP 96 Map-Reply for [8190] 52:54:00:19:93:e9/48 <-- LISP Map-Reply providing the RLOC-MAC association 90 12.072455 52:54:00:1e:ad:00 -> 52:54:00:19:93:e9 ARP 110 10.47.4.3 is at 52:54:00:1e:ad:00 <-- VXLAN Encapsulated ARP Reply that is injected by the CPU
È possibile utilizzare il comando show platform arpsnooping client <indirizzo MAC di origine> per visualizzare le azioni intraprese su Edge-2 in relazione alla risposta ARP
Edge-2#show platform arpsnooping client 5254.001e.ad00 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.001E.AD00: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
2023/10/24 20:47:38.151 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED INPUT 2023/10/24 20:47:38.151 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:TO_ARPSND 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PSISF_PRE:PSP_INJNEUTRAL 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:BD_DPIDX_TO_FWDPLANE
Edge-1 (10.47.1.12)
Edge-1 riceve la risposta ARP incapsulata VXLAN, spegne l'intestazione VXLAN e porta la risposta ARP alla CPU per un'ulteriore elaborazione.
Edge-1#debug platform software infrastructure punt
*Oct 24 21:42:11.303: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 24 21:42:11.303: Punt: IP proto src 173.0.10.47, dst 4.3.82.84, from table 0, intf L2LI0, encap LISP, size 60, cause snoop packets(L3) <-- Can see 10.47.4.3 IP address that has been obscured *Oct 24 21:42:11.303: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 24 21:42:11.303: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
È possibile utilizzare il comando show platform arpsnooping client <indirizzo MAC di origine> per ottenere ulteriori informazioni sulla gestione della risposta ARP su Edge-1
Edge-1#show platform arpsnooping client 5254.001e.ad00 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.001E.AD00: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED INPUT 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED_TUNNEL 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:SHUNTED 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:BD_DPIDX_TO_FWDPLANE
Edge-1 riceve la risposta ARP puntuale e invia la risposta ARP alla VLAN 1026, alla porta su cui risiede l'endpoint 10.47.4.2
Edge-1#show mac address-table address 5254.0019.93e9
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
1026 5254.0019.93e9 DYNAMIC Gi1/0/3
Total Mac Addresses for this criterion: 1
Percorso ARP flooding (L2 Flooding)
Con L2 Flooding, la risoluzione ARP può anche verificarsi dove tutti i nodi Fabric Edge nel fabric nonché L2 Handoff/IP Directed Broadcast enabled Borders si uniscono a un comune gruppo multicast di underlay. Ogni volta che un pacchetto/frame idoneo per il flooding arriva a un nodo Edge, è la VXLAN incapsulata con l'indirizzo IP di destinazione del gruppo multicast sottostante. L'inondazione L2 può essere applicata alla risoluzione ARP in alcuni scenari:
- Il comando flood arp-end viene configurato nell'istanza L2 LISP per la VLAN. I frame broadcast ARP vengono trasmessi a tutti i Fabric Edges utilizzando il gruppo multicast broadcast-underlay.
- Il comando flood arp-end è configurato ma per Cisco Catalyst Center quando in un pool è abilitato il flooding L2 e il pool non è contrassegnato come wireless
- Il multicast sottostante deve essere configurato tramite l'automazione LAN o la configurazione manuale. Nessuno dei flussi di lavoro multicast dell'infrastruttura configura automaticamente il multicast sottostante.
Una volta configurato il multicast di underlay e abilitata la funzione flood arp-end, viene modificata la modalità di gestione della richiesta ARP, che in origine utilizzava la risoluzione basata su LISP/SISF. Dopo aver configurato il comando flood arp-end nell'istanza LISP L2, questo disattiva la policy LISP-ARP-RELAY-VLAN IPDT per la VLAN e non viene usato.
Edge-1#show device-tracking policies vlan 1026 Target Type Policy Feature Target range vlan 1026 VLAN DT-PROGRAMMATIC Device-tracking vlan all vlan 1026 VLAN LISP-DT-GLEAN-VLAN-MULTI-IP Device-tracking vlan all
Verifica richiesta ARP percorso di flooding
Edge-1 (10.47.1.12)
Dopo aver ricevuto una richiesta ARP dal client nella VLAN l2 abilitata per il flooding con arp-nd configurato, non viene più gestita dallo snooping ARP. La richiesta ARP viene inoltrata alla CPU per scopi di apprendimento IPDT, ma non per l'inoltro.
ARP Snooper non elabora la richiesta ARP, che può essere visualizzata con il comando show platform arpsnooping client <indirizzo MAC>
Edge-1#show platform arpsnooping client 5254.0019.93e9
PLAT_DAI : Platform DAI shim
FWDPLANE : Dataplane forwarding
BRIDGE : Packet to be bridged
ARPSN : Arp Snooping
Packet Trace for client MAC 5254.0019.93E9:
Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action
----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
Filtered entries counters:
ARPSN_FILTER_SVI: 0
Edge-1 non crea una voce RMT IPDT per l'endpoint 10.47.4.3 come evidenziato nell'output
Edge-1#show monitor capture 1 buffer display-filter arp brief
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
1 0.000000 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2
Edge-1#show device-tracking database address 10.47.4.3
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
Network Layer Address Link Layer Address Interface vlan prlvl age state Time left
A questo punto, la richiesta ARP è una VXLAN incapsulata nel gruppo multicast broadcast underlay. Edge-1 ha un percorso con Loopback0 come origine e il gruppo il gruppo broadcast underlay.
Edge-1#show run int lo0 Building configuration... Current configuration : 135 bytes ! interface Loopback0 ip address 10.47.1.12 255.255.255.255 no ip redirects ip pim sparse-mode <-- PIM must be enabled ip router isis clns mtu 1400 end
Edge-1#show ip mroute 239.0.17.2
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert, # - iif-starg configured on rpf intf,
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 239.0.17.2), 5w1d/00:02:05, RP 10.47.1.14, flags: SJC
Incoming interface: GigabitEthernet1/0/2, RPF nbr 10.47.1.4
Outgoing interface list:
L2LISP0.8190, Forward/Sparse-Dense, 01:56:41/00:00:18, flags:
L2LISP0.8192, Forward/Sparse-Dense, 2w2d/00:00:58, flags:
L2LISP0.8188, Forward/Sparse-Dense, 5w1d/00:01:58, flags:
(10.47.1.12, 239.0.17.2), 00:02:53/00:00:06, flags: PFT <-- Lo0 interface of Edge-1
Incoming interface: Null0, RPF nbr 0.0.0.0, <-- Incoming interface Null0 is expected
Outgoing interface list:
GigabitEthernet1/0/2, Forward/Sparse, 00:04:40/00:02:45, flags: <-- Outgoing interface Gig1/0/2 faces the fabric underlay
In realtà, flood arp-end alterna IPDT/SISF piuttosto che allagare se stesso. L2 flooding già inonda le trasmissioni, ma il trucco è quello di disabilitare la politica LISP AR da device-tracking, la proprietà di ARP è ora rilasciata e può essere inondata come qualsiasi altra trasmissione.
Per verificare la programmazione hardware per il flooding L2, utilizzare il comando show platform software dpidb l2lisp <L2 LISP ID>
Edge-1#show platform software dpidb l2lisp 8190 Instance Id:8190, dpidx:25, vlan:1026, Parent Interface:L2LISP0(if_id:23) <-- dpidx value used in the next command
Utilizzare il valore dpidx del comando precedente e usare il comando show platform software fed switch active ifm if-id <dpidx value>
Edge-1#show platform software fed switch active ifm if-id 25 Interface IF_ID : 0x0000000000000019 Interface Name : L2LISP0.8190 Interface Block Pointer : 0x7f65ec85ba78 Interface Block State : READY Interface State : Enabled Interface Status : ADD, UPD Interface Ref-Cnt : 2 Interface Type : L2_LISP Created Time : 2023/09/19 17:57:32.046 Last Modified Time : 2023/10/25 17:59:09.265 Current Time : 2023/10/25 20:15:44.624 Is top interface : FALSE Asic_num : 0 Switch_num : 0 AAL port Handle : 7a00003a Parent interface id : 17 Multicast Tunnel IP : 239.0.17.2 Mcast Tunnel Handle : 0x7f65ed356918 L2 Multicast Tunnel IP : 0.0.0.0 L2 Multicast Vlan Id : 0 L2 Multicast Tunnel Hdl : NULL Vlan Id : 1026 Instance Id : 8190 Dest Port : 4789 SGT : Enable Underlay VRF (V4) : 0 Underlay VRF (V6) : 0 Flood Access-tunnel : Disable Flood unknown ucast : Enable Broadcast : Enable Multicast Flood : Enable L2 Multicast Flood : Disable Host Activity report: Enabled <snip>
È possibile utilizzare EPC su Gi1/0/2 nella direzione di uscita, poiché questa richiesta ARP viene inoltrata in entrata e in uscita senza richiedere un inserimento della CPU, questa volta è possibile considerare attendibili le acquisizioni EPC nella decisione di uscita.
Edge-1#monitor capture 1 start Started capture point : 1 Edge-1#monitor capture 1 stop Capture statistics collected at software: Capture duration - 22 seconds Packets received - 5 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1
Edge-1#show monitor capture 1 buffer brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit 1 0.000000 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 110 Who has 10.47.4.3? Tell 10.47.4.2 <-- Size 110 because VXLAN, UDP, and other headers
È possibile esaminare più da vicino la richiesta ARP incapsulata VXLAN
Edge-1#show monitor capture 1 buffer display-filter frame.number==1 detailed
Starting the packet display ........ Press Ctrl + Shift + 6 to exit
Frame 1: 110 bytes on wire (880 bits), 110 bytes captured (880 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0
Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe)
Interface name: /tmp/epc_ws/wif_to_ts_pipe
Encapsulation type: Ethernet (1)
Arrival Time: Oct 25, 2023 20:44:36.578645000 UTC
[Time shift for this packet: 0.000000000 seconds]
Epoch Time: 1698266676.578645000 seconds
[Time delta from previous captured frame: 0.000000000 seconds]
[Time delta from previous displayed frame: 0.000000000 seconds]
[Time since reference or first frame: 0.000000000 seconds]
Frame Number: 1
Frame Length: 110 bytes (880 bits)
Capture Length: 110 bytes (880 bits)
[Frame is marked: False]
[Frame is ignored: False]
[Protocols in frame: eth:ethertype:ip:udp:vxlan:eth:ethertype:arp]
Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) <-- Ignore the all 0s MAC, not accurate
Destination: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Source: 00:00:00:00:00:00 (00:00:00:00:00:00)
Address: 00:00:00:00:00:00 (00:00:00:00:00:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: IPv4 (0x0800)
Internet Protocol Version 4, Src: 10.47.1.12, Dst: 239.0.17.2 <-- Source is Edge-1 RLOC, Destination is the broadcast underlay group
0100 .... = Version: 4
.... 0101 = Header Length: 20 bytes (5)
Differentiated Services Field: 0x00 (DSCP: CS0, ECN: Not-ECT)
0000 00.. = Differentiated Services Codepoint: Default (0)
.... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0)
Total Length: 96
Identification: 0x8dab (36267)
Flags: 0x4000, Don't fragment
0... .... .... .... = Reserved bit: Not set
.1.. .... .... .... = Don't fragment: Set
..0. .... .... .... = More fragments: Not set
Fragment offset: 0
Time to live: 255
Protocol: UDP (17)
Header checksum: 0xe2a3 [validation disabled]
[Header checksum status: Unverified]
Source: 10.47.1.12
Destination: 239.0.17.2
User Datagram Protocol, Src Port: 65280, Dst Port: 4789
Source Port: 65280
Destination Port: 4789
Length: 76
[Checksum: [missing]]
[Checksum Status: Not present]
[Stream index: 0]
[Timestamps]
[Time since first frame: 0.000000000 seconds]
[Time since previous frame: 0.000000000 seconds]
Virtual eXtensible Local Area Network
Flags: 0x8800, GBP Extension, VXLAN Network ID (VNI)
1... .... .... .... = GBP Extension: Defined
.... .... .0.. .... = Don't Learn: False
.... 1... .... .... = VXLAN Network ID (VNI): True
.... .... .... 0... = Policy Applied: False
.000 .000 0.00 .000 = Reserved(R): 0x0000
Group Policy ID: 0
VXLAN Network Identifier (VNI): 8190 <-- L2 LISP IID
Reserved: 0
Ethernet II, Src: 52:54:00:19:93:e9 (52:54:00:19:93:e9), Dst: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) <-- SMAC and DMAC of the ARP Request
Destination: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
Address: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast)
Source: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
Address: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
.... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: ARP (0x0806)
Trailer: 000000000000000000000000000000000000
Address Resolution Protocol (request)
Hardware type: Ethernet (1)
Protocol type: IPv4 (0x0800)
Hardware size: 6
Protocol size: 4
Opcode: request (1)
Sender MAC address: 52:54:00:19:93:e9 (52:54:00:19:93:e9)
Sender IP address: 10.47.4.2
Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00)
Target IP address: 10.47.4.3
Edge-2 (10.47.1.13)
Edge-2 si unisce al gruppo broadcast underlay, 239.0.17.2 e ha S,G per Edge-1, riceve il pacchetto multicast incapsulato VXLAN su Gig1/0/1 e l'interfaccia secondaria LISP0.8190 è nell'elenco delle interfacce in uscita. Nelle versioni precedenti, ad esempio la 17.3 o una versione precedente, il codice utilizza un'interfaccia tunnel anziché una sottointerfaccia LISP0.
Edge-2#show ip mroute 239.0.17.2
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert, # - iif-starg configured on rpf intf,
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 239.0.17.2), 5w1d/stopped, RP 10.47.1.14, flags: SJC
Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.6
Outgoing interface list:
L2LISP0.8190, Forward/Sparse-Dense, 02:28:57/00:01:02, flags:
L2LISP0.8192, Forward/Sparse-Dense, 2w2d/00:00:32, flags:
L2LISP0.8188, Forward/Sparse-Dense, 5w1d/00:02:54, flags:
(10.47.1.12, 239.0.17.2), 00:00:03/00:02:56, flags: JT
Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.6 <-- Interface that faces the fabric underlay and the RPF interface towards 10.47.1.12
Outgoing interface list:
L2LISP0.8188, Forward/Sparse-Dense, 00:00:03/00:02:56, flags:
L2LISP0.8192, Forward/Sparse-Dense, 00:00:03/00:02:56, flags:
L2LISP0.8190, Forward/Sparse-Dense, 00:00:03/00:02:56, flags:
Edge-2 riceve il pacchetto incapsulato VXLAN, spegne l'intestazione VXLAN e instrada il pacchetto nella VLAN 1026, che può essere visualizzata in un EPC sull'interfaccia in arrivo e sull'interfaccia rivolta verso l'endpoint.
Edge-2#monitor capture 1 interface gig1/0/1 in match any Edge-2#monitor capture 1 int g1/0/3 out Edge-2#monitor capture 1 start Started capture point : 1 Edge-2#monitor capture 1 stop Capture statistics collected at software: Capture duration - 22 seconds Packets received - 43 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1 Edge-2#show monitor capture 1 buffer display-filter arp Starting the packet display ........ Press Ctrl + Shift + 6 to exit 10 6.230153 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 110 Who has 10.47.4.3? Tell 10.47.4.2 <-- Size 110 is the VXLAN encapsulated ARP Request 11 6.404781 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 <-- Size 60 is the original ARP Request
Verifica risposta ARP percorso di flooding
Le risposte ARP sono quasi sempre unicast, a meno che non siano ARP gratuite. Per le risposte ARP unicast, non esiste alcuna distinzione tra il flusso di lavoro per Percorso unicast basato su LISP/SISF o il percorso di inondazione basato su Flood Arp-end, entrambi utilizzano lo stesso percorso unicast che include il rilevamento SISF/IPDT. Per la risoluzione dei problemi, è possibile utilizzare la sezione Verifica risposta ARP percorso unicast.
Cronologia delle revisioni
| Revisione | Data di pubblicazione | Commenti |
|---|---|---|
2.0 |
26-Oct-2023 |
Release iniziale |
1.0 |
12-Aug-2020 |
Versione iniziale |
Feedback