RFC1483 ブリッジング（aal5snap）を使用して IRB、NAT、DHCP を実行する Cisco 827 ルータと IRB を実行する Cisco 6400 ルータを設定する方法

ダウンロードオプション

PDF (94.5 KB)
Adobe Reader を使ってさまざまなデバイスで表示
ePub (82.3 KB)
iPhone、iPad、Android、ソニーの Reader、または Windows Phone 上で、さまざまなアプリを使って表示
Mobi (Kindle) (102.0 KB)
Kindle デバイスで、または Kindle アプリを使って複数のデバイスで表示

Updated: 2008 年 2 月 26 日

Document ID:12899

偏向のない言語

この製品のドキュメントセットは、偏向のない言語を使用するように配慮されています。このドキュメントセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージの取り組みの詳細は、こちらをご覧ください。

翻訳について

シスコは世界中のユーザにそれぞれの言語でサポートコンテンツを提供するために、機械と人による翻訳を組み合わせて、本ドキュメントを翻訳しています。ただし、最高度の機械翻訳であっても、専門家による翻訳のような正確性は確保されません。シスコは、これら翻訳の正確性について法的責任を負いません。原典である英語版（リンクからアクセス可能）もあわせて参照することを推奨します。

Introduction

Before You Begin

Conventions

Prerequisites

Components Used

Configure

Network Diagram

Configurations

Verify

Troubleshoot

Related Information

Introduction

This sample configuration shows a Cisco 827 Digital Subscriber Line (DSL) Router connecting to a Cisco 6130 Digital Subscriber Line Access Multiplexer (DSLAM) and terminating on a Cisco 6400 Universal Access Concentrator (UAC).

The Cisco 827 is configured as follows:

With Integrated Routing and Bridging (IRB)
Using encapsulation
With Network Address Translation (NAT)
As a Dynamic Host Configuration Protocol (DHCP) server that will lease IP addresses to its local Ethernet clients

The Cisco 6400 is configured with IRB.

Before You Begin

Conventions

For more information on document conventions, see the Cisco Technical Tips Conventions.

Prerequisites

There are no specific prerequisites for this document.

Components Used

The information in this document is based on the software and hardware versions below.

Cisco 827-4V Customer Premises Equipment (CPE) IOS® Software Release 12.1(1)XB
Cisco 6400 UAC-Node Route Processor (NRP) IOS Software Release 12.0(7)DC
Cisco 6400 UAC-Node Switch Processor (NSP) IOS Software Release 12.0(4)DB
Cisco 6130 DSLAM-NI2 IOS Software Release 12.1(1)DA

The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .

Network Diagram

This document uses the network setup shown in the diagram below.

Configurations

This document uses the configurations shown below.

Cisco 827
Cisco Access 6400 NRP

Cisco 827
Current configuration: ! version 12.0 service timestamps debug datetime msec service timestamps log datetime msec ! hostname R1 ! ip subnet-zero ! ip dhcp excluded-address 10.0.0.1 ! ip dhcp pool *<pool name>* network 10.0.0.0 255.0.0.0 default-router 10.0.0.1 ! bridge irb ! interface Ethernet0 ip address 10.0.0.1 255.0.0.0 no ip directed-broadcast ip nat inside no ip mroute-cache ! interface ATM0 no ip address no ip directed-broadcast no ip mroute-cache no atm ilmi-keepalive pvc 1/150 encapsulation aal5snap ! bundle-enable bridge-group 1 hold-queue 224 in ! interface BVI1 ip address 172.16.0.1 255.255.0.0 no ip directed-broadcast ip nat outside ! ip nat inside source list 1 interface BVI1 overload ip classless ip route 0.0.0.0 0.0.0.0 172.16.0.2 no ip http server ! access-list 1 permit 10.0.0.0 0.255.255.255 bridge 1 protocol ieee bridge 1 route ip ! voice-port 1 timing hookflash-in 0 ! voice-port 2 timing hookflash-in 0 ! voice-port 3 timing hookflash-in 0 ! voice-port 4 timing hookflash-in 0 ! end

Cisco 827

Current configuration: 
! 
version 12.0 
service timestamps debug datetime msec 
service timestamps log datetime msec 
!
hostname R1 
! 
ip subnet-zero 
! 
ip dhcp excluded-address 10.0.0.1
!
ip dhcp pool 
<pool name>
 
   network 10.0.0.0 255.0.0.0 
   default-router 10.0.0.1
! 
bridge irb 
! 
interface Ethernet0 
 ip address 10.0.0.1 255.0.0.0 
 no ip directed-broadcast 
 ip nat inside
 no ip mroute-cache 
! 
interface ATM0 
 no ip address 
 no ip directed-broadcast 
 no ip mroute-cache 
 no atm ilmi-keepalive 
 pvc 1/150 
  encapsulation aal5snap 
 !
 bundle-enable 
 bridge-group 1 
 hold-queue 224 in
! 
interface BVI1 
 ip address 172.16.0.1 255.255.0.0 
 no ip directed-broadcast 
 ip nat outside
! 
ip nat inside source list 1 interface BVI1 overload 
ip classless 
ip route 0.0.0.0 0.0.0.0 172.16.0.2 
no ip http server 
! 
access-list 1 permit 10.0.0.0 0.255.255.255
bridge 1 protocol ieee 
 bridge 1 route ip
! 
voice-port 1 
 timing hookflash-in 0 
!
voice-port 2 
 timing hookflash-in 0
!
voice-port 3
 timing hookflash-in 0 
! 
voice-port 4 
 timing hookflash-in 0 
! 
end

Cisco Access 6400 NRP
Current configuration: ! version 12.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname NRP ! ip subnet-zero ! bridge irb ! interface ATM0/0/0 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache no atm ilmi-keepalive ! interface ATM0/0/0.300 point-to-point no ip directed-broadcast no ip route-cache pvc 1/150 encapsulation aal5snap ! bridge-group 1 ! interface Ethernet0/0/1 no ip address no ip directed-broadcast ! interface Ethernet0/0/0 no ip directed-broadcast ! interface FastEthernet0/0/0 no ip address no ip directed-broadcast full-duplex ! interface BVI1 ip address 172.16.0.2 255.255.0.0 no ip directed-broadcast ! no ip http server ! bridge 1 protocol ieee bridge 1 route ip ! end

Cisco Access 6400 NRP

Current configuration:
! 
version 12.0
service timestamps debug datetime msec 
service timestamps log datetime msec 
no service password-encryption 
! 
hostname NRP
! 
ip subnet-zero 
! 
bridge irb 
! 
interface ATM0/0/0 
 no ip address 
 no ip directed-broadcast 
 no ip route-cache 
 no ip mroute-cache 
 no atm ilmi-keepalive 
!
interface ATM0/0/0.300 point-to-point 
 no ip directed-broadcast
 no ip route-cache 
 pvc 1/150 
  encapsulation aal5snap 
 ! 
 bridge-group 1 
! 
interface Ethernet0/0/1 
 no ip address
 no ip directed-broadcast 
! 
interface Ethernet0/0/0 
 no ip directed-broadcast 
! 
interface FastEthernet0/0/0 
 no ip address 
 no ip directed-broadcast 
 full-duplex 
! 
interface BVI1 
 ip address 172.16.0.2 255.255.0.0 
 no ip directed-broadcast 
! 
no ip http server 
!
bridge 1 protocol ieee 
 bridge 1 route ip 
! 
end

In order to make sure that the wireless clients can communicate among them, configure the bridge-group 1 command on the radio interface.

When the bridge-group 1 command is issued on the radio interface, these commands are automatically issued:

bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source

Do not disable these commands. These commands are required for the wireless communication to occur. If these commands are disabled, wireless clients may not be able to communicate with each other.

Also, if the bridge-group command is not configured for the VLAN, the wireless clients are not able to get the IP address from the Dynamic Host Configuration Protocol (DHCP) server on one of the VLANs.