この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
この章では、Content Switching Module(CSM;コンテント スイッチング モジュール)の設定方法について説明します。
ここでは、CSMコマンドについて簡単に説明します。CSMの設定および使用方法の詳細については、該当する各項を参照してください。
|
|
---|---|
CSMのCLI(コマンドライン インターフェイス)を使用すると、次の操作が実行できます。
コマンドを入力して ? キーを押すか、または help コマンドに続けてコマンドを入力すると(例: help aaa )、サマリーが表示されます。
設定モードを開始する場合はconfig tコマンド、設定を表示する場合は write t コマンド ステートメント、フラッシュ メモリに書き込む場合は write m コマンドを使用します。ほとんどのコマンドで、 show コマンドは sh に短縮できます。この機能は、コマンド完成機能といいます。
• Internet Assigned Number Authority(IANA)のWebサイトでポート番号およびプロトコル番号を確認します。
http://www.iana.org/assignments/port-numbers
http://www.iana.org/assignments/protocol-numbers
• テキスト エディタで設定を作成し、カット アンド ペーストで設定を編集します。
カット アンド ペーストは1行ごと、または設定全体で行えます。広い範囲をペーストしたときには、誤りがないように必ず設定を確認してください。
CSMの設定方法の詳細については、『 Catalyst 6500 Series Content Switching Module Installation and Configuration Note 』を参照してください。
CSMに関する技術資料は、次のURLからオンラインで参照できます。
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/mod_icn/csm
CSMではCisco IOS技術に基づくコマンド セットを使用でき、次の各コマンド モードを利用してコマンド イネーブル モードで設定変更できます。
(注) Catalystオペレーティングシステムが稼働しているスイッチでCSMを使用する場合、ルータ プロンプトを表示するためにMultilayer Switch Feature Card(MSFC;マルチレイヤ スイッチ フィーチャ カード)とのセッションを開始する必要があります。
ユーザ モードを使用すると、CSMの設定を確認できます。CSMにアクセスすると、ユーザ モードのプロンプトが次のように表示されます。
ユーザ モードのコマンドはすべてイネーブル モードで使用できます。ユーザ モードからイネーブル モードを開始するには、次のようにenableコマンドを使用します。
イネーブル モードを終了してユーザ モードに戻るには、次のようにexitまたはendコマンドを使用します。
イネーブル モードを終了してユーザ モードに戻るには、次のようにdisableコマンドを使用します。
コンフィギュレーション モードを使用すると、CSMの設定を変更できます。このモードでは、イネーブル モード、ユーザ モード、およびコンフィギュレーション モードのすべてのコマンドが使用できます。コンフィギュレーション モードを開始するには、次のようにconfigure terminalコマンドを使用します。
コンフィギュレーション モードを終了してイネーブル モードに戻るには、次のようにexitまたはendコマンドを使用します。
コンフィギュレーション モードを終了してユーザ モードに戻るには、次のようにdisableコマンドを使用します。
CSMコマンドで使用される正規表現は、UNIXのファイル名仕様に準拠します。正規表現は、次のコマンドで使用します。
• 「match protocol http cookie(cookieマップ サブモード)」
• 「match protocol http header(ヘッダー マップ サブモード)」
• 「match protocol http url(URLマップ サブモード)」
|
|
---|---|
|
|