この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
目次
この付録では、Cisco Unified IP Phone 6901 および 6911 の電話機に使用する壁面取り付けキットの設置について説明します。
次の項では、Cisco Unified IP Phone 6901 に使用する壁面取り付けプレートの設置方法について説明します。
Cisco Unified IP Phone 6901 を取り付けるには、Leviton 社製壁面取り付けプレート(Leviton 型式番号:4108W-0SP)を使用することを推奨します。 壁面取り付けプレートは、電話機とは別に注文する必要があります。
次の図と表は、Leviton 社製壁面取り付けプレートを使用して Cisco Unified IP Phone 6901 を壁面に取り付けるために必要な項目のリストを示しています。
1 |
RJ45 コネクタ |
2 |
Leviton 社製壁面取り付けプレート |
ステップ 1 |
電話回線コード(RJ45 コネクタ)を電話機の底部にある電話機のジャックに差し込みます。
|
||||||||
ステップ 2 |
RJ45 コネクタを壁面取り付けプレートにある電話機のジャックに差し込みます。
|
||||||||
ステップ 3 |
取り付け穴を壁面取り付けプレートの底部に合わせ、壁面取り付けピンにかぶせます。
|
||||||||
ステップ 4 |
IP Phone を所定の場所にしっかりはめ込みます。
|
||||||||
ステップ 5 | ハンドセット レストの調整の説明に従って、ハンドセットを変更します。 |
次の項では、Cisco Unified IP Phone 6911 に使用する壁面取り付けキットの設置方法について説明します。
次の図は、 Cisco Unified IP Phone 6911 用の壁面取り付けキットに含まれている項目のリストを示しています。
現在、目的の位置に電話用のイーサネット ジャックが存在しない場合は、イーサネット ジャックも設置します。 このジャックには、イーサネット接続のために適切に配線されている必要があります。 通常の電話ジャックは使用できません。 電話の設置要件と配線の詳細については、Cisco Unified IP Phone の設置を参照してください。
ステップ 1 |
取り付け位置に、壁面用ブラケットを取り付けます。 壁面用ブラケットをイーサネット ジャックにかぶせて取り付けることも、近くのジャックまでイーサネット ネットワーク ケーブルを配線することもできます。
|
ステップ 2 |
IP Phone に電話機用ブラケットを装着します。
|
ステップ 3 |
イーサネット ケーブルを 10/100 SW ネットワーク ポートと壁面のジャックに接続します。 電話機にネットワーク デバイス(コンピュータなど)を接続する場合、ケーブルを 10/100 PC アクセス ポートに装着します。 外部電源を使用する場合、電源コードを電話機に差し込み、電話本体の 10/100 PC ポートの横に付いているクリップで、コードをはさんで固定します。 |
ステップ 4 | 電話機用ブラケットの上部にあるタブを壁面ブラケットのスロットに挿入して、電話機を壁面ブラケットに装着します。 ブラケット背後の壁面に差し込み口がある場合を除き、すべての電源コードやその他のケーブルが、ブラケット下部のケーブル アクセス用開口部を通っていることを確認します。 電話機用ブラケットと壁面用ブラケットの開口部によって、複数の円形の開口部ができ、1 つの開口部に 1 本のケーブルを通すことができるようになっています。 |
ステップ 5 |
ロックの鍵を使用して、電話を壁面用ブラケットにロックします。
|
ステップ 6 | ハンドセット レストの調整の説明に従って、ハンドセットを変更します。 |
電話機が壁に取り付けられている場合は、受話器が受け台から滑り落ちないようにハンドセットの受け台を調整する必要があります。 フックのツメが見えた状態になります。このツメは、電話機を垂直にしたときにハンドセットの置き場所になります。 下の図と手順に従って、フックスイッチ フックを変更します。
1 |
受け台からハンドセットを外し、ハンドセット レストからプラスチック タブを引き出します。 |
2 |
タブを 180 度回します。 |
3 |
角のノッチが手前になるように、2 本指でタブを持ちます。 |
4 |
タブを受け台のスロットに合わせ、スロット内に均等に押し込みます。 回したタブの上部から突起が出ている状態になります。 ハンドセットをハンドセット レストに戻します。 |