The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Executive overview
This antenna reference guide explains issues and concerns about antennas used with a Cisco Aironet and Catalyst wireless LAN system or wireless bridge system. It details deployment and design, limitations and capabilities, and basic theories of antennas. This document also contains information about the Cisco antennas and accessories, as well as installation scenarios, regulatory information, and technical specifications and diagrams of the available antennas.
Overview of antennas
Each Cisco Aironet radio product is designed to perform in a variety of environments. Implementing the antenna system can greatly improve coverage and performance.
To optimize the overall performance of a Cisco wireless LAN, it is important to understand how to maximize radio coverage with the appropriate antenna selection and placement. An antenna system comprises numerous components, including the antenna, mounting hardware, connectors, antenna cabling, and in some cases a lightning arrestor. For a consultation, please contact a Cisco Aironet partner at: https://tools.cisco.com/WWChannels/LOCATR/jsp/partner_locator.jsp.
Cisco partners can provide onsite engineering assistance for complex requirements.
Antenna properties and ratings
An antenna gives the wireless system three fundamental properties: gain, direction, and polarization. Gain is a measure of increase in power. Direction is the shape of the transmission pattern. A good analogy for an antenna is the reflector in a flashlight. The reflector concentrates and intensifies the light beam in a particular direction similar to what a parabolic dish antenna would do to an RF source in a radio system.
Antenna gain is measured in decibels, which is a ratio between two values. The gain of a specific antenna is compared to the gain of an isotropic antenna. An isotropic antenna is a theoretical antenna with a uniform three-dimensional radiation pattern (similar to a light bulb with no reflector). The decibels over an isotropic radiator (dBi) value is used to compare the power level of a given antenna to the theoretical isotropic antenna. The U.S. regulatory agency (the Federal Communications Commission, or FCC) uses dBi in its calculations. An isotropic antenna is said to have a power rating of 0 dB, meaning that it has zero gain/loss when compared to itself.
Unlike isotropic antennas, dipole antennas are real antennas. Dipole antennas have a different radiation pattern compared to isotropic antennas. The dipole radiation pattern is 360 degrees in the horizontal plane and 75 degrees in the vertical plane (assuming the dipole antenna is standing vertically) and resembles a doughnut in shape. Because the beam is “slightly” concentrated, dipole antennas have a gain over isotropic antennas of 2.14 dB in the horizontal plane. Dipole antennas are said to have a gain of 2.14 dBi (in comparison to an isotropic antenna).
Some antennas are rated in comparison to dipole antennas. This is denoted by the suffix dBd, short for decibels over a dipole antenna. Hence, dipole antennas have a gain of 0 dBd (= 2.14 dBi).
Note that the majority of documentation refers to dipole antennas as having a gain of 2.2 dBi. The actual figure is 2.14 dBi, but it is often rounded up.
Cisco offers several different styles of antennas for use with access points and bridges in both 2.4-GHz and 5-GHz products. Every antenna offered for sale has been FCC-approved. Each type of antenna has different coverage capabilities. As the gain of an antenna increases, there is some tradeoff in its coverage area. Usually high-gain antennas offer longer coverage distances, but only in a certain direction. The radiation patterns described below show the coverage areas of the styles of antennas that Cisco offers: dipole, omnidirectional, and patch antennas.
Omnidirectional antennas
An omnidirectional antenna (Figure 1) is designed to provide a 360-degree radiation pattern. This type of antenna is used when coverage in all directions from the antenna is required. The standard 2.14-dBi “rubber duck” is one style of omnidirectional antenna.
Omnidirectional antenna
Directional antennas
Directional antennas come in many different styles and shapes. An antenna does not offer any added power to the signal; it simply redirects the energy it receives from the transmitter. By redirecting this energy, it has the effect of providing more energy in one direction and less energy in all other directions. As the gain of a directional antenna increases, the angle of radiation usually decreases, providing a greater coverage distance but with a reduced coverage angle. Directional antennas include patch antennas (Figure 2) and parabolic dishes. Parabolic dishes have a very narrow RF energy path, and the installer must be accurate in aiming these types of antennas at each other.
Directional patch antenna
Cabling
Cabling introduces losses into the system, negating some of the gain an antenna introduces and reducing the range of the RF coverage.
Interconnect cable
Attached to all antennas (except the standard dipoles), this cable provides a 50-ohm impedance to the radio and antenna, with a flexible connection between the two items. It has a high loss factor and should not be used except for very short connections (usually less than 10 feet). Typical length on all antennas is 36 inches.
Low-loss and ultra-low-loss cable
Cisco offers two styles of cables for use with the 2.4-GHz and 5-GHz product lines. These cables provide a much lower loss factor than standard interconnect cables, and they can be used when the antenna must be placed at any distance from the radio device. While these are low-loss cables, they should still be kept to a minimum length.
Two types of cables are available for mounting the antenna away from the radio unit. The 100- and 150-foot cables are LMR600-type cables, while the 20- and 50-foot cables are LMR400-type cables. All four lengths are supplied with one reverse polarity-TNC (RP-TNC) plug and one RP-TNC jack connector attached. This allows for connection to the radio unit and to the interconnect cable supplied on the antenna.
Connectors
According to the U.S. Federal Code of Regulations, products used in the 2.4- and 5-GHz ISM bands manufactured after June 1994 must either use connectors that are unique and nonstandard (meaning not readily available on the market) or be designed to be professionally installed (“professional” here indicates a person trained in RF installation and regulations). Since many of the 2.4-GHz products are installed by non-RF-trained personnel, these products must comply with the unique connector rule. The Cisco outdoor access and bridge products are designed for installation by an RF professional, and therefore may use a standard N-style connector. Cisco Aironet indoor products use RP-TNC connectors. While these are similar to the normal TNC connectors, they cannot be mated to the standard connectors.
Cisco has recently introduced a new multi-RF connector known as DART. DART connectors can support four or eight RF signals along with several electrical pins. Cisco developed the DART connector to simplify installations and to create a single insertion cable to go along with a new line of self-identifying antennas (SIA) containing circuitry to automate provisioning and detection.
To ensure compatibility with Cisco products, use antennas and cabling from Cisco.
Note: Self-Identifying Antennas (SIA) are supported starting from IOS XE 17.5.1 and later software for C9800 WLCs.
Mounting hardware
Each antenna requires some type of mounting. The standard dipole antenna simply connects to the RP-TNC connector on the unit. Mast-mount antennas are designed to mount to a variety of mast diameters, and each comes with mounting hardware for attachment. Patch antennas are designed to mount flat against a wall or ceiling, and ceiling-mount antennas are equipped with a drop-ceiling cross-member attachment.
For most indoor applications, a. 75- or 1-inch electrical conduit provides a suitable mounting. For outdoor applications, use a heavy galvanized or aluminum wall mast that will withstand the wind-loading rating of the selected antenna.
Lightning arrestors
When using outdoor antenna installations, it is always possible that an antenna will suffer damage from charges developing on the antenna and cable, or surges induced from nearby lightning strikes. The Cisco Aironet lightning arrestor is designed to protect 2.4-GHz to 5-GHz radio equipment from static electricity and lightning-induced surges that travel on coaxial transmission lines. Both systems need to be properly grounded as identified in the hardware installation manuals of the products. These protection mechanisms will not prevent damage in the event of a direct lightning hit.
Theory of operation
The Cisco Aironet Lightning Arrestor (Figure 3) prevents energy surges from reaching the RF equipment by shunting them to the ground. Surges are limited to less than 50 volts, in about 0.0000001 second (100 nanoseconds). A typical lightning surge is about 0.000002 second (2 microseconds).
Cisco Aironet Lightning Arrestor
The accepted IEEE transient (surge) suppression is 0.000008 second (8 microseconds). The Cisco Aironet Lightning Arrestor is a 50-ohm transmission line with a gas discharge tube positioned between the center conductor and ground. This gas discharge tube changes from an open circuit to a short circuit almost instantaneously in the presence of voltage and energy surges, providing a path to ground for the energy surge.
Installation
This arrestor is designed to be installed between your antenna cable and the Aironet access point. Installation should be indoors or inside a protected area. A good ground must be attached to the arrestor. This can be accomplished by attaching a ground lug to the arrestor and using a heavy wire (number 6 solid copper) to connect the lug to a good earth ground.
Cisco Aironet antenna descriptions
Table 1. Antennas for 2.4-, 5- and 6- GHz for indoor access points
Cisco part number |
Antenna type |
Description |
Gain |
AIR-ANT2524DB-R AIR-ANT2524DB-R= |
Black dipole, 1 port |
Single black dipole antenna with RP-TNC connector. The antenna provides indoor omnidirectional coverage. It has a 90-degree articulation radius and can be used with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
AIR-ANT2524DG-R AIR-ANT2524DG-R= |
Gray dipole, 1 port |
Single gray dipole antenna with RP-TNC connector. The antenna provides indoor omnidirectional coverage. It has a 90-degree articulation radius and can be used with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
AIR-ANT2524DW-R AIR-ANT2524DW-R= |
White dipole, 1 port |
Single white dipole antenna with RP-TNC connector. The antenna provides indoor omnidirectional coverage. It has a 90-degree articulation radius and can be used with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
AIR-ANT2535SDW-R AIR-ANT2535SDW-R= AIR-ANT2535SDW-RS(=) |
White dipole, 1 port |
Single white dipole antenna with RP-TNC connector. The antenna provides indoor omnidirectional coverage. It does not articulate, as the other dipole antennas do. It can be used with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 3 dBi 5 GHz: 5 dBi |
AIR-ANT2524DW-RS AIR-ANT2524DW-RS= |
White dipole, 1 port (self-identifying circuitry) |
Single white dipole antenna with RP-TNC connector. The antenna provides indoor omnidirectional coverage. It has a 90-degree articulation radius and can be used with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
AIR-ANT2524V4C-R= AIR-ANT2524V4C-RS= |
Omnidirectional, 4 ports (all ports dual band) |
Ceiling-mount omnidirectional antenna. Designed for indoor use, this antenna comes with ceiling mount hardware. It has 4 plenum-rated pigtail cables, 3 ft each, with 4 RP-TNC connectors. Designed for use with access points having dual-band ports, such as the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access point. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
AIR-ANT2544V4M-R= AIR-ANT2544V4M-RS= |
Omnidirectional, 4 ports (all ports dual band) |
Indoor/outdoor wall- or mast-mounted dual-band omnidirectional antenna with 4 plenum-rated, 36-in. cables and RP-TNC connectors. Designed for use with access points having dual-band ports, such as the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access point. |
2.4 GHz: 4 dBi 5 GHz: 4 dBi |
AIR-ANT2544V4M-R8= |
Omnidirectional, 4 ports (all ports dual band) |
Dual-band Multiple-Input, Multiple-Output (MIMO) wall-mounted omnidirectional antenna with 8-ft antenna cable operates in the 2.4- and 5-GHz frequency ranges and is designed for indoor or outdoor use with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 3 dBi 5 GHz: 2 dBi |
AIR-ANT2566P4W-R= AIR-ANT2566P4W-RS= |
Patch, 4 ports (all ports dual band)) |
Indoor/outdoor wall-mounted dual-band patch antenna with 4 plenum-rated, 36-in. cables and RP-TNC connectors. Designed for use with access points having dual-band ports, such as the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 6 dBi 5 GHz: 6 dBi |
AIR-ANT2566D4M-R= AIR-ANT2566D4M-RS= |
Patch, 4 ports (all ports dual band)) |
Dual-band MIMO wall-mounted directional array antenna operates in the 2.4- and 5-GHz frequency ranges and is designed for indoor or outdoor use with the Aironet 1830, 1850, 2800, and 3800 Series and Cisco Catalyst 9115AX, 9120AX, 9130AX Series access points. |
2.4 GHz: 6 dBi 5 GHz: 6 dBi |
C-ANT9101= |
Omnidirectional,8 ports |
Tri-band MIMO Ceiling mount omnidirectional antenna operates in the 2.4-, 5- and 6-GHz frequency ranges and supports IoT. This antenna is designed for indoor use with 9130AX Series access points |
2.4 GHz: 2 dBi 5 GHz: 3 dBi 6 GHz: 3 dBi IoT: 3 dBi |
C-ANT9102= |
Omnidirectional,8 ports |
Tri-band MIMO Wall/Pole mount omnidirectional antenna operates in the 2.4-, 5- and 6-GHz frequency ranges and supports IoT. This antenna is designed for indoor use with 9130AX Series access points |
2.4 GHz: 4 dBi 5 GHz: 4 dBi 6 GHz: 4 dBi IoT: 4 dBi |
C-ANT9103= |
Directional, 8 ports |
Tri-band MIMO Wall/Pole mount directional antenna operates in the 2.4-, 5- and 6-GHz frequency ranges and supports IoT. This antenna is designed for indoor use with 9130AX Series access points |
2.4 GHz: 6 dBi 5 GHz: 6 dBi 6 GHz: 6 dBi IoT: 6 dBi |
C-ANT9104= |
Directional, 8 ports |
Dual-band MIMO Wall/Pole mount directional antenna operates in the 2.4- and 5-GHz frequency ranges with beamwidth switching and beamsteering (boresight, +/-10 degs, and +/-20 degs) capabilities at 5 GHz. This antenna supports IoT and is designed for indoor or outdoor use with 9130AX Series access points |
2.4 GHz: 6 dBi 5 GHz wide beamwidth: 7 dBi 5 GHz narrow beamwidth, (boresight, +/-10 degs, +/-20 degs): 10 dBi IoT: 6 dBi |
Table 2. 2.4-GHz and 5-GHz access point and bridge antennas with N-type connectors
Cisco part number |
Antenna type |
Description |
Gain |
AIR-ANT2420V-N (=) |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1570 Series mesh access points. It is only 5 in. long, mounts directly to the access point, and has no cable attachments. |
2 dBi |
AIR-ANT2450V-N (=) |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
5 dBi |
AIR-ANT2455V-N= |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
5.5 dBi |
AIR-ANT2450V-N-HZ (=) |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
5 dBi |
AIR-ANT2450VG-N (=) |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
5 dBi |
AIR-ANT2450HG-N (=) |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
5 dBi |
AIR-ANT2480V-N (=) |
Omnidirectional |
2.4-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
8 dBi |
AIR-ANT2413P2M-N= |
Patch, 2 ports |
2.4-GHz directional antenna with 2 orthogonally polarized ports. Comes with two 30-in. cables terminated in right-angle N-type connectors. Suitable for use on Aironet 1560 and 1570 Series mesh access points. |
13 dBi |
AIR-ANT5140V-N (=) |
Omnidirectional |
5-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
4 dBi |
AIR-ANT5150VG-N (=) |
Directional |
5-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 mesh access points. It mounts directly to the access point and has no cable attachments. |
5 dBi |
AIR-ANT5150HG-N (=) |
Directional |
5-GHz omnidirectional antenna for mesh access points. Suitable for use on Aironet 1560 and 1570 mesh access points. It mounts directly to the access point and has no cable attachments. |
5 dBi |
AIR-ANT5180V-N (=) |
Omnidirectional |
5-GHz omnidirectional antenna for mesh access points. Suitable for use on Cisco Aironet 1560 and 1570 Series mesh access points. It mounts directly to the access point and has no cable attachments. |
8 dBi |
AIR-ANT5114P-N= |
Patch |
5-GHz patch antenna for use in the 4950- to 5850-MHz frequency band. Has an N-type connector and will require a separate low-loss cable for mounting to the access point. Articulating mount included. Fits mast poles with a maximum diameter of 2 in. Suitable for use on Aironet outdoor access points. |
14 dBi |
AIR-ANT5114P2M-N= |
Patch, 2 ports |
5-GHz, directional antenna with 2 orthogonally polarized ports. Comes with two 30-in. cables terminated in right-angle N-type connectors. Suitable for use on Aironet outdoor access points. |
14 dBi |
Table 3. 2.4-GHz and 5-GHz dual-band antennas with N-type connectors
Cisco part number |
Antenna type |
Description |
Gain |
AIR-ANT2547V-N (=) AIR-ANT2547VG-N (=) AIR-ANT2547VG-NS (=) |
Omnidirectional |
Dual-band omnidirectional antenna that uses an N-type connector. It mounts directly to the access point and has no cable attachments. AIR-ANT2547VG-N has a gray radome. Suitable for use on Aironet outdoor access points. |
2.4 GHz: 4 dBi 5 GHz: 7 dBi |
AIR-ANT2547V-N-HZ (=) |
Omnidirectional |
Dual-band omnidirectional antenna that uses an N-type connector. It mounts directly to the access point and has no cable attachments. Used in hazardous locations. Suitable for use on Aironet outdoor access points. |
2.4 GHz: 4 dBi 5 GHz: 7 dBi |
AIR-ANT2568VG-N (=) AIR-ANT2568VG-NS(=) |
Omnidirectional |
Dual-band omnidirectional antenna that uses an N-type connector. It mounts directly to the access point and has no cable attachments. It has a gray radome. |
2.4 GHz: 6 dBi 5 GHz: 8 dBi |
AIR-ANT2588P3M-N= |
Patch, 3 ports |
Dual-band directional antenna with 3 N-type connectors. It can be used with the outdoor access points and has no cable attachments. |
2.4 GHz: 8 dBi 5 GHz: 8 dBi |
AIR-ANT2513P4M-N= AIR-ANT2513P4M-NS(=) |
Patch, 4 ports |
Dual-band directional antenna with 4 N-type connectors. It is outdoor rated and has no cable attachments. |
2.4 GHz: 13 dBi 5 GHz: 13 dBi |
Table 4. 2.4-GHz and 5-GHz access point and bridge integrated antennas
Cisco part number |
Antenna type |
Description |
Gain |
Integrated Aironet 3500 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 3 dBi |
Integrated Aironet 600 Series OfficeExtend (OEAP600)antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high performance in ceiling-, wall-, and desk-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 2 dBi 5 GHz: 2 dBi |
Integrated Aironet 700 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 5 dBi |
Integrated Aironet 700W Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high-performance wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
Integrated Aironet 1600 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 4 dBi |
Integrated Aironet 2600 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 4 dBi |
Integrated Aironet 3600 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
Integrated Aironet 3700 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 4 dBi |
Integrated Aironet 2700 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 4 dBi |
Integrated Aironet 1700 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz designed for high performance in both ceiling- and wall-mount applications. Antennas provide hemispherical coverage and cannot be removed from the access point. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 4 dBi |
Integrated Aironet 1550 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
Integrated Aironet 1530 Series antenna |
Omnidirectional |
802.11n antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 5 dBi |
Integrated Aironet 1570 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 6 dBi |
Integrated Aironet 1815 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
Integrated Aironet 1840 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 5 dBi |
Integrated Aironet 1830/1850 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 5 dBi |
Integrated Aironet 2800 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 6 dBi |
Integrated Aironet 3800 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 6 dBi |
Integrated Aironet 4800 Series antenna |
Omnidirectional |
802.11ac antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 2.5 dBi 5 GHz: 5 dBi |
Integrated Cisco Catalyst 9105AXi Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 4 dBi |
Integrated Cisco Catalyst 9105AXW Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 4 dBi |
Integrated Cisco Catalyst 9115AX Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 4 dBi |
Integrated Cisco Catalyst 9117AX Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 6 dBi |
Integrated Cisco Catalyst 9120AX Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 5 dBi |
Integrated Cisco Catalyst 9130AX Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 6 dBi |
Integrated Cisco Catalyst 9124AX Series antenna |
Omnidirectional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 7 dBi 5 GHz: 7 dBi BLE Antenna Gain: 5 dBi |
Integrated Cisco Catalyst 9124AXD Series antenna |
Directional |
802.11ax antenna package for both 2.4 GHz and 5 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides directional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 9 dBi 5 GHz: 9 dBi BLE Antenna Gain: 4 dBi |
Integrated Cisco Catalyst 9136 Series antenna |
Omnidirectional |
802.11ax antenna package for 2.4 GHz, 5 GHz and 6 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 5 dBi 6 GHz: 6 dBi |
Integrated Cisco Catalyst 9166I Series antenna |
Omnidirectional |
802.11ax antenna package for 2.4 GHz, 5 GHz and 6 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 5 dBi 5 GHz(XOR): 5 dBi 6 GHz: 4 dBi |
Integrated Cisco Catalyst 9164 Series antenna |
Omnidirectional |
802.11ax antenna package for 2.4 GHz, 5 GHz and 6 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 3 dBi 5 GHz: 5 dBi 6 GHz: 4 dBi |
Integrated Cisco Catalyst 9162 Series antenna |
Omnidirectional |
802.11ax antenna package for 2.4 GHz, 5 GHz and 6 GHz. When the integrated antenna version is ordered, this antenna is attached to the access point and provides omnidirectional coverage in a low-profile package. No connectors are offered for additional external antennas. |
2.4 GHz: 4 dBi 5 GHz: 5 dBi 6 GHz: 5 dBi |
Cisco Aironet cable descriptions
Table 5 defines the cables available for interconnecting the antennas and the radio devices for the Cisco Aironet product line.
Table 5. Cisco cables
Cisco part number |
Type of cable |
Description |
Loss at 2.4 GHz |
Loss at 5.8 GHz |
AIR-CAB002L240-N= |
Interconnect |
2-ft low-loss cable, one straight N connector, one 90-degree N connector |
0.5 dB |
0.8 dB |
AIR-CAB005LL-N |
Interconnect |
5-ft low-loss cable, one straight N connector, one 90-degree N connector |
0.5 dB |
0.8 dB |
AIR-CAB005LL-R |
Interconnect |
5-ft low-loss cable, one RP-TNC plug, one RP‑TNC jack |
0.5 dB |
0.8 dB |
AIR-CAB005LL-R-N= |
Interconnect |
5-ft low-loss cable, one RP-TNC plug, one 90-degree N male connector |
0.5 dB |
0.8 dB |
AIR-CAB010LL-N |
Interconnect |
10-ft low-loss cable, one straight N connector, one 90-degree N connector |
0.9 dB |
1.5 dB |
AIR-CAB020LL-R |
Interconnect |
20-ft low-loss cable, one RP-TNC plug, one RP‑TNC jack |
1.3 dB |
2.5 dB |
AIR-CAB050LL-R |
Interconnect |
50-ft low-loss cable, one RP-TNC plug, one RP‑TNC jack |
3.4 dB |
5.75 dB |
AIR-CAB100ULL-R |
Interconnect |
100-ft ultra-low-loss cable, one RP-TNC plug, one RP-TNC jack |
4.4 dB |
7.25 dB |
AIR-CAB150ULL-R |
Interconnect |
150-ft ultra-low-loss cable, one RP-TNC plug, one RP-TNC jack |
6.6 dB |
11 dB |
AIR-CAB025HZ-N= |
Interconnect |
25-ft ultra-low-loss cable, two straight N male connectors, ruggedized jacket for use in hazardous locations |
2.0 dB |
3.5 dB |
AIR-ACC2537-060 |
Bulkhead extender |
5-ft (60-in.) RG-58 type cable with one RP‑TNC plug and one RP-TNC jack |
2 dB |
3 dB |
AIR-CAB002-D8-R= |
Interconnect |
2-ft (24-in.) breakout cable with DART-8 connector and eight RP-TNC jacks |
2 dB |
2.3 dB |
AIR-CAB-003-D8-N= |
Interconnect |
3-ft (36-in.) breakout cable with DART-8 connector and eight N-type (male) connectors |
2 dB |
2.3 dB |
AIR-CAB-003-D8-D8= |
Interconnect |
3-ft (36-in.) jumper cable with DART-8 connectors (one end straight, one end right angle) |
2.1 dB |
3.1 dB |
Table 6. Accessories
Cisco part number |
Name |
Description |
AIR-ACC245LA-R |
Lightning arrestor |
Supports both 2.4-GHz and 5-GHz operation with RP-TNC connectors. Prevents lightning and related energy surges at the antenna from reaching the radio circuitry. A ground ring is included. |
AIR-ACC245LA-N= |
Lightning arrestor |
Supports both 2.4-GHz and 5-GHz operation with N-type connectors. Prevents lightning and related energy surges at the antenna from reaching the radio circuitry. A ground ring is included. |
Cisco Aironet antenna specifications
The following section provides detailed descriptions, including physical and electrical specifications, for the antennas offered by Cisco for the Cisco Aironet and Cisco Catalyst product lines. A full, detailed installation guide for each antenna can be found at the following: https://www.cisco.com/en/US/products/hw/wireless/ps469/prod_installation_guides_list.html.
AIR-ANT2524DB-R, AIR-ANT2524DG-R, AIR-ANT2524DW-R, AIR-ANT2524DW-RS(=)
Dimensions and mounting specifications |
Azimuth and elevation plane radiation pattern |
|
|
Frequency range |
2.4 to 2.5 GHz 5.150 to 5.925 GHz |
VSWR |
Less than 2:1 |
Gain |
2.4 GHz: 2 dBi 5 GHz: 4 dBi |
Polarization |
Linear |
Azimuth 3-dB beamwidth |
Omnidirectional |
Elevation 3-dB beamwidth |
40 degrees |
Antenna connector |
RP-TNC |
Cable length |
None |
Dimensions |
6.6 in. (16.8 cm) |
Mounting |
To RP-TNC connector |
AIR-ANT2535SDW-R
Dimensions and mounting specifications |
Azimuth and elevation plane radiation pattern |
Frequency range |
2.4 to 2.5 GHz 5.150 to 5.925 GHz |
VSWR |
Less than 2:1 |
Gain |
2.4 GHz: 3 dBi 5 GHz: 5 dBi |
Polarization |
Linear |
Azimuth 3-dB beamwidth |
Omnidirectional |
Elevation 3-dB beamwidth |
40 degrees |
Antenna connector |
RP-TNC |
Cable length |
None |
Dimensions |
3.3 in. (8.4 cm) |
Mounting |
To RP-TNC connector |
Dual-band ceiling-mount omnidirectional, 4 elements
AIR-ANT2524V4C-R(=), AIR-ANT2524V4C-RS(=)
Frequency range |
2.400 to 2.484 GHz 5.150 to 5.850 GHz |
VSWR |
2:1 |
Gain |
● 2 dBi in 2.4 GHz
● 4 dBi in 5 GHz
|
Polarization |
Linear |
Azimuth 3-dB beamwidth |
Omni |
Elevation 3-dB beamwidth |
● 69 degrees in 2.4 GHz
● 60 degrees in 5 GHz
|
Antenna connector |
4 RP-TNC male |
Cable length |
36 in. (91 cm) plenum rated |
Dimensions |
7.25 x 7.25 x 1 in (18.4 x 18.4 x 2.5 cm) |
Mounting |
Ceiling |
Dual-band wall-mount omnidirectional, 4 elements
AIR-ANT2544V4M-R=, AIR-ANT2544V4M-RS=
Frequency range |
2.400 to 2.484 GHz 5.150 to 5.850 GHz |
VSWR |
2:1 |
Gain |
● 4 dBi in 2.4 GHz
● 4 dBi in 5 GHz
|
Polarization |
Linear |
Azimuth 3-dB beamwidth |
Omnidirectional |
Elevation 3-dB beamwidth |
● 60 degrees in 2.4 GHz
● 33 degrees in 5 GHz
|
Antenna connector |
4 RP-TNC male |
Cable length |
36 in. (91 cm) plenum rated |
Dimensions |
8.6 x 6.3 in. dia. (21.8 x 16 cm dia.) |
Mounting |
Wall or mast |
Dual-band wall-mount directional array antenna
AIR-ANT2566D4M-R(=), AIR-ANT2566D4M-RS(=)
Frequency range |
2.400 to 2.484 GHz 5.150 to 5.850 GHz |
VSWR |
2:1 |
Gain |
● 6 dBi in 2.4 GHz
● 6 dBi in 5 GHz
|
Polarization |
Linear |
Azimuth 3-dB beamwidth |
● 65 degrees in 2.4 GHz
● 55 degrees in 5 GHz
|
Elevation 3-dB beamwidth |
● 60 degrees in 2.4 GHz
● 55 degrees in 5 GHz
|
Antenna connector |
4 RP-TNC male |
Cable length |
36 in. (91 cm) |
Mounting |
Wall or mast |
Dual-band wall-mount patch, 4 elements
AIR-ANT2566P4W-R=, AIR-ANT2566P4W-RS=
Frequency range |
2.400 to 2.484 GHz 5.150 to 5.850 GHz |
VSWR |
2:1 |
Gain |
● 6 dBi in 2.4 GHz
● 6 dBi in 5 GHz
|
Polarization |
Linear |
Azimuth 3-dB beamwidth |
● 105 degrees in 2.4 GHz
● 125 degrees in 5 GHz
|
Elevation 3-dB beamwidth |
● 70 degrees in 2.4 GHz
● 60 degrees in 5 GHz
|
Antenna connector |
4 RP-TNC male |
Cable length |
36 in. (91 cm) plenum rated |
Dimensions |
11 x 6.3 x 1.2 in (28 x 16 x 3 cm) |
Mounting |
Wall |
Dual-band wall-mount stadium antenna
AIR-ANT2513P4M-N, AIR-ANT2513P4M-NS=
Frequency range |
2.4 to 2.5 GHz 5.15 to 5.925 GHz |
VSWR |
2.4 GHz: 1.6:1 5.7 to 5.9 GHz: 1.5:1 |
Gain |
● 13 dBi in 2.4 GHz
● 13 dBi in 5 GHz
|
Polarization |
Linear |
Azimuth 3-dB beamwidth |
● 31 degrees in 2.4 GHz
● 31 degrees in 5 GHz
|
Elevation 3-dB beamwidth |
● 33 degrees in 2.4 GHz
● 27 degrees in 5 GHz
|
Antenna connector |
N-female bulkhead |
Mounting |
Wall |
2-dBi direct-mount omnidirectional
AIR-ANT2420V-N
Dimensions and mounting specifications |
|
Frequency range |
2.4 to 2.5 GHz |
VSWR |
<2:1 |
Gain |
2 dBi |
Polarization |
Linear, vertical |
Azimuth 3-dB beamwidth |
Omnidirectional |
Elevation 3-dB beamwidth |
30 degrees for 2.4 GHz; 14 degrees for 5 GHz |
Antenna connector |
N-male |
Cable length |
None |
Dimensions |
5 x 1 in. (12.7 x 2.5 cm) |
Mounting |
Direct mount |
Wind rating (operational) |
125 mph (201 km/h) |
Wind rating (survival) |
165 mph (265 km/h) |
5-dBi direct-mount omnidirectional
AIR-ANT2450V-N, AIR-ANT2450VG-N, AIR-ANT2450V-N-HZ, AIR-ANT2450HG-N
The AIR-ANT2450V-N, AIR-ANT2450VG-N, and AIR-ANT2450V-N-HZ share the same radiation patterns. The AIR-ANT2450HG-N has a different pattern.
Dimensions and mounting specifications |
Azimuth plane radiation pattern |
Elevation plane radiation pattern |
AIR-ANT2450HG-N radiation pattern |
Frequency range |
2.4 to 2.5 GHz |
|
|
VSWR |
1:7:1 (AIR-ANT2450V-N) 2:1 (AIR-ANT2450VG-N, AIR-ANT2450V-N-HZ, AIR-ANT2450HG-N) |
|
|
Gain |
5 dBi |
|
|
Polarization |
Linear AIR-ANT2450V-N: Vertical AIR-ANT2450V-N-HZ: Horizontal AIR-ANT2450HG-N: Horizontal |
|
|
Azimuth 3-dB beamwidth |
Omnidirectional |
|
|
Elevation 3-dB beamwidth |
30 degrees |
|
|
Antenna connector |
N-male |
|
|
Cable length |
None |
|
|
Dimensions |
AIR-ANT2450V-N: 11 x 1 in. (27.9 x 2.5 cm) AIR-ANT2450VG-N, AIR-ANT2450V-N-HZ, AIR-ANT2450HG-N:12.9 x 1.5 in (32.8 x 3.8 cm) |
|
|
Mounting |
Direct mount |
|
|
Wind rating (operational) |
AIR-ANT2450V-N: 125 mph (201 km/h) AIR-ANT2450VG-N, AIR-ANT2450V-N-HZ, AIR-ANT2450HG-N: 100 mph (161 kph) |
|
|
Wind rating (survival) |
AIR-ANT2450V-N: 165 mph (265 km/h) |
|
AIR-ANT2455V-N
Dimensions and mounting specifications |
Azimuth plane radiation pattern |
Elevation plane radiation pattern |
Frequency range |
2.4 to 2.83 GHz |
|
VSWR |
2:1 or better |
|
Gain |
5.5 dBi |
|
Polarization |
Linear |
|
Azimuth plane 3-dB beamwidth |
Omnidirectional |
|
Elevation plane 3-dB beamwidth |
25 degrees |
|
Connectors |
N |
|
Cable length |
None |
|
Dimensions |
12.5 x 1 in. (31.7 x 2.5 cm) |
|
Mounting |
Direct mount |
AIR-ANT2480V-N(=)
Dimensions and mounting specifications |
Azimuth plane radiation pattern |
Elevation plane radiation pattern |
Frequency range |
2.4 to 2.5 GHz |
|
VSWR |
1:6:1 |
|
Gain |
8 dBi |
|
Polarization |
Linear, vertical |
|
Azimuth 3-dB beamwidth |
10 degrees |
|
Elevation 3-dB beamwidth |
Omnidirectional |
|
Antenna connector |
N-male |
|
Cable length |
None |
|
Dimensions |
19.5 x 7/8 in. (49.5 x 2.2 cm) |
|
Mounting |
Direct mount |
|
Wind rating (operational) |
100 mph (161 km/h) |
|
Wind rating (survival) |
165 mph (265 km/h) |
AIR-ANT2413P2M-N=
|
Azimuth/elevation radiation pattern |
|
|
Frequency range |
2.400 to 2.484 GHz |
VSWR |
2:1 |
Gain |
13 dBi |
Polarization |
Linear, dual |
Azimuth 3-dB beamwidth |
30 degrees |
Elevation 3-dB beamwidth |
30 degrees |
Antenna connector |
2 right-angle N-male |
Cable length |
30 in. (76 cm) |
Dimensions |
7.8 x 7.8 x 1.2 in. (19.8 x 19.8 x 3 cm) |
Mounting |
Wall or mast |
4-dBi direct-mount omnidirectional
AIR-ANT5140V-N(=)
Dimensions and mounting specifications |
|
Frequency range |
5.25 to 5.875 GHz |
VSWR |
<2:1 |
Gain |
4 dBi |
Polarization |
Linear, vertical |
Azimuth 3-dB beamwidth |
Omni |
Elevation 3-dB beamwidth |
45 degrees |
Antenna connector |
N-male |
Cable length |
None |
Dimensions |
5 x 1 in. (12.7 x 2.5 cm) |
Mounting |
Direct mount |
Wind rating (operational) |
125 mph (201 km/h) |
Wind rating (survival) |
165 mph (265 km/h) |
8-dBi direct-mount omnidirectional
AIR-ANT5180V-N
Dimensions and mounting specifications |
Azimuth plane radiation pattern |
Elevation plane radiation pattern |
Frequency range |
4.9 to 5.85 GHz |
|
VSWR |
1:7:1 |
|
Gain |
8 dBi |
|
Polarization |
Linear, vertical |
|
Azimuth 3-dB beamwidth |
Omnidirectional |
|
Elevation 3-dB beamwidth |
16 degrees |
|
Antenna connector |
N-male |
|
Cable length |
None |
|
Dimensions |
11 x 1 in. (27.9 x 2.5 cm) |
|
Mounting |
Direct mount |
|
Wind rating (operational) |
125 mph (201 km/h) |
|
Wind rating (survival) |
165 mph (265 km/h) |
5-dBi direct-mount directional
AIR-ANT5150VG-N, AIR-ANT5150HG-N
Dimensions and mounting specifications |
AIR-ANT5150VG-N radiation pattern |
AIR-ANT5150 HG-N radiation pattern |
|
||
Frequency range |
5.150 to 5.925 GHz |
|
VSWR |
2:1 |
|
Gain |
5 dBi |
|
Polarization |
Linear AIR-ANT5150VG-N: Vertical |
|
Azimuth 3-dB beamwidth |
Omnidirectional |
|
Elevation 3-dB beamwidth |
30 degrees |
|
Antenna connector |
N-male |
|
Cable length |
None |
|
Dimensions |
7.8 x 1 in. (20 x 2.5 cm) |
|
Mounting |
Direct mount |
|
Wind rating (operational) |
100 mph (161 km/h) |
AIR-ANT5114P-N(=)
Dimensions and mounting specifications |
Azimuth plane radiation pattern |
Elevation plane radiation pattern |
Frequency range |
4.9 to 5.85 GHz |
|
VSWR |
2:1 |
|
Gain |
● 4.9 to 5.4 GHz: 13 dBi
● 5.4 to 5.85 GHz: 14 dBi
|
|
Polarization |
Linear, vertical |
|
Azimuth 3-dB beamwidth |
25 degrees |
|
Elevation 3-dB beamwidth |
29 degrees |
|
Antenna connector |
N-female |
|
Cable length |
1 ft. (0.3 m) |
|
Dimensions |
4 1/8 x 4 1/8 in. (1.3 x 1.3 cm) |
|
Mounting |
Wall or mast |
AIR-ANT5114P2M-N=
|
Azimuth/elevation radiation pattern |
|
|
||
Frequency range |
5.150 to 5.900 GHz |
|
VSWR |
2:1 |
|
Gain |
14 dBi |
|
Polarization |
Linear, dual |
|
Azimuth 3-dB beamwidth |
30 degrees |
|
Elevation 3-dB beamwidth |
30 degrees |
|
Antenna connector |
2 right-angle N-male |
|
Cable length |
30 in. (76 cm) |
|
Dimensions |
7.8 x 7.8 x 1.2 in. (19.8 x 19.8 x 3 cm) |
|
Mounting |
Wall or mast |
AIR-ANT2547V-N, AIR-ANT2547VG-N, AIR-ANT2547V-N-HZ, AIR-ANT2547VG-NS(=)
2.4-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz azimuth plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
2.400 to 2.483 MHz 5.150 to 5.875 MHz |
VSWR |
2:1 |
Gain |
● 4 dBi in 2.4 GHz
● 7 dBi in 5 GHz
|
Polarization |
Linear, vertical |
Azimuth 3-dB beamwidth |
Omnidirectional |
Elevation 3-dB beamwidth |
● 30 degrees in 2.4 GHz
● 14 degrees in 5 GHz
|
Antenna connector |
N-type male |
Cable length |
None |
Dimensions |
11.1 x 1.25 in. dia. (28.2 x 3.2 cm dia.) |
Mounting |
Direct mount |
Wind rating (operational) |
100 mph (161 km/h) |
Wind rating (survival) |
165 mph (265 km/h) |
AIR-ANT2568VG-N, AIR-ANT2568VG-NS(=)
2.4-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz azimuth plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
2.400 to 2.483 GHz 5.150 to 5.925 GHz |
VSWR |
1.5:1 (2.4 GHz) 2:1 (5 GHz) |
Gain |
● 6 dBi in 2.4 GHz
● 8 dBi in 5 GHz
|
Polarization |
Linear, vertical |
Azimuth 3-dB beamwidth |
Omnidirectional |
Elevation 3-dB beamwidth |
● 24 degrees in 2.4 GHz
● 11 degrees in 5 GHz
|
Antenna connector |
N-type male |
Cable length |
None |
Dimensions |
14.8 x 1.5 in. dia. (37.7 x 3.8 cm dia.) |
Mounting |
Direct mount |
Wind rating (operational) |
100 mph (161 km/h) |
Wind rating (survival) |
136 mph (218 km/h) |
AIR-ANT2588P3M-N=
Frequency range |
2.400 to 2.500 GHz 5.150 to 5.900 GHz |
VSWR |
2:1 |
Gain |
8 dBi, both bands |
Polarization |
Linear, dual (2 vertical, 1 horizontal) |
Azimuth 3-dB beamwidth |
120 degrees |
Elevation 3-dB beamwidth |
30 degrees |
Antenna connector |
3 N-female |
Cable length |
None |
Dimensions |
12 x 7 x 1.1 in. (30.5 x 17.8 x 2.8 cm) |
Mounting |
Wall or mast |
C-ANT9101
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.484 GHz
● 5.15 to 7.125 GHz
|
||
Gain |
● 2 dBi at 2.4 GHz
● 6 dBi for ports A through D and 3 dBi for ports E through H at 5 GHz
|
||
Polarization |
Dual polarized |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Antenna connector |
DART connector |
||
Mounting |
Ceiling mount |
||
Antenna type |
Omnidirectional |
C-ANT9102
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.484 GHz
● 5.15 to 7.125 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Dual polarized |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 60 degrees, 5 GHz = 30 degrees |
||
Antenna connector |
DART connector |
||
Mounting |
Wall or pole |
||
Antenna type |
Omnidirectional |
C-ANT9103
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.484 GHz
● 5.15 to 7.125 GHz
|
||
Gain |
● 2.4 GHz: 6 dBi
● 5 GHz: 6 dBi
|
||
Polarization |
Dual polarized |
||
Azimuth 3-dB beamwidth |
Directional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 75 degrees, 5 GHz = 70 degrees |
||
Antenna connector |
Right-angle DART-8 |
||
Mounting |
Wall or pole mount |
||
Antenna type |
Directional |
Cisco Aironet 1040, 1140, 3500i Series integrated antennas*
2.4-GHz 4-dBi azimuth plane radiation pattern |
5-GHz 3-dBi azimuth plane radiation pattern |
2.4-GHz 4-dBi elevation plane radiation pattern |
5-GHz 3-dBi elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 3 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet OEAP600 Series integrated antenna
2.4-GHz 4-dBi azimuth plane radiation pattern |
5-GHz 3-dBi azimuth plane radiation pattern |
2.4-GHz 4-dBi elevation plane radiation pattern |
5-GHz 3-dBi elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 2 dBi
● 5 GHz: 2 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 700i Series integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 3 dBi
● 5 GHz: 5 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 130 degrees, 5 GHz = 130 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Ceiling |
||
Antenna type |
Omnidirectional |
Cisco Aironet 700W Series integrated antennas
2.4-GHz radiation pattern |
5-GHz radiation pattern |
Frequency range |
2.4 to 2.5 GHz, 5.150 to 5.850 GHz |
Gain |
2.4 GHz = 2 dBi 5 GHz = 4 dBi |
Polarization |
Linear, vertical |
Azimuth 3-dB beamwidth |
2.4 GHz = 130 degrees, 5 GHz = 80 degrees |
Elevation 3-dB beamwidth |
2.4 GHz = 180 degrees, 5 GHz = 100 degrees |
Antenna connector |
Integrated |
Mounting |
Wall plate |
Cisco Aironet 3600i integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 2 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 2600i integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevations 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1600i integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 3700i integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 2700i integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1700i integrated antennas
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1550 Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 2 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Azimuth 3-dB beamwidth |
Omnidirectional |
||
Elevation 3-dB beamwidth |
2.4 GHz = 120 degrees, 5 GHz = 120 degrees |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1530 Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 3 dBi
● 5 GHz: 5 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1570 Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 6 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1815 (i, t, w, m) Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 2 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1840 Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 5 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 1830/1850 Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 3 dBi
● 5 GHz: 5 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Aironet 2800 and 3800 Series integrated antenna
Dimensions and mounting specifications |
|
Frequency range |
2.4 to 2.5 GHz 5.15 to 5.85 GHz |
Gain |
FRA: 2.4 GHz: 4 dBi, 5 GHz: 6 dBi 5 GHz: 5 dBi |
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
FRA: 2.4 GHz: Omnidirectional, 5 GHz: Directional 5 GHz: Omnidirectional |
Cisco Aironet 4800 Series integrated antenna
Dimensions and mounting specifications |
|
Frequency range |
2.4 to 2.5 GHz 5.15 to 5.85 GHz |
Gain |
FRA: 2.4 GHz: 2.5 dBi, 5 GHz: 5 dBi 5 GHz: 3.5 dBi |
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
FRA: 2.4 GHz: Omnidirectional, 5 GHz: Directional 5 GHz: Omnidirectional |
Cisco Catalyst 9105AX Series integrated antenna
Dimensions and mounting specifications |
|
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
Gain |
Catalyst 9105AXW
● 2.4 GHz: Peak gain 3 dBi
● 5 GHz: Peak gain 5 dBi
Catalyst 9105AXI
● 2.4 GHz: Peak gain 4 dBi
● 5 GHz: Peak gain 5 dBi
|
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
Omnidirectional |
Cisco Catalyst 9115AX Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5-GHz elevation plane radiation pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 3 dBi
● 5 GHz: 4 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Catalyst 9117AX Series integrated antenna
2.4-GHz azimuth plane radiation pattern |
5-GHz azimuth plane radiation pattern |
2.4-GHz elevation plane radiation pattern |
5 GHz, Elevation Plane Radiation Pattern |
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
||
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 6 dBi
|
||
Polarization |
Linear, vertical |
||
Antenna connector |
Integrated |
||
Mounting |
Integrated |
||
Antenna type |
Omnidirectional |
Cisco Catalyst 9120AX Series integrated antenna
Dimensions and mounting specifications |
|
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
Gain |
● FRA: 2.4 GHz: 4 dBi, 5 GHz: 5 dBi
● 5 GHz: 4 dBi
|
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
● FRA: 2.4 GHz: Omnidirectional, 5 GHz: Omnidirectional
● 5 GHz: Omnidirectional
|
Cisco Catalyst 9130AX Series integrated antenna
Dimensions and mounting specifications |
|
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
Gain |
● 2.4 GHz: 4 dBi, 5 GHz: 6 dBi
|
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
Omnidirectional |
Cisco Catalyst 9124AX Series integrated Omni directional antenna
Dimensions and mounting specifications |
|
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
Gain |
● 2.4 GHz: 7 dBi, 5 GHz: 7 dBi
● BLE antenna gain – 5 dBi
|
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
Omnidirectional |
Cisco Catalyst 9124AX Series integrated Directional antenna
Dimensions and mounting specifications |
|
Frequency range |
● 2.4 to 2.5 GHz
● 5.15 to 5.85 GHz
|
Gain |
● 2.4 GHz: 7 dBi, 5 GHz: 7 dBi
● BLE antenna gain – 5 dBi
|
Polarization |
Linear, Dual |
Mounting |
Integrated |
Azimuth |
2.4 GHz- 70 deg, 5 GHz – 65 deg |
Elevation |
2.4 GHz- 55 deg, 5 GHz – 50 deg |
Antenna connector |
Integrated |
Antenna type |
Directional |
Cisco Catalyst 9136 Series integrated antenna
Dimensions and mounting specifications |
|
Frequency range |
● 2.4 to 2.4835 GHz
● 5.15 to 5.85 GHz
● 5.925 to 6.425 GHz
|
Gain |
● 2.4 GHz: 4 dBi
● 5 GHz: 5 dBi
● 6 GHz: 6 dBi
|
Polarization |
Linear, vertical |
Mounting |
Integrated |
Antenna connector |
Integrated |
Antenna type |
Omnidirectional |
Cisco Catalyst 9166 Series integrated antenna
Cisco Catalyst 9164 Series integrated antenna
Cisco Catalyst 9162 Series integrated antenna
Antenna patterns for Catalyst 9162I 2.4-GHz and 5-GHz client serving radios
Antenna patterns for Catalyst 9162I 6-GHz client serving and scanning radios
Antenna patterns for Catalyst 9162I 2.4-GHz and 5-GHz scanning radios
Antenna patterns for Catalyst 9162I 6-GHz scanning radio and 2.4-GHz IoT radio