-
이 Applied Mitigation Bulletin은 PSIRT Security Advisory Multiple Vulnerabilities in Cisco Intrusion Prevention System Software에 대한 첨부 문서이며 관리자가 Cisco 네트워크 장치에 구축할 수 있는 식별 및 완화 기술을 제공합니다.
-
Cisco Intrusion Prevention System에는 여러 취약점이 있습니다. 다음 하위 섹션에는 이러한 취약성이 요약되어 있습니다.
Cisco IPS Software Malformed IP Packets Denial of Service 취약성: 이 취약성은 인증 및 최종 사용자 상호 작용 없이 원격으로 악용될 수 있습니다. 이 취약성을 성공적으로 악용하면 DoS(서비스 거부) 조건이 발생할 수 있습니다. 이 취약성을 악용하려는 시도가 반복되면 DoS 상태가 지속될 수 있습니다. 익스플로잇을 위한 공격 벡터는 잘못된 형식의 IPv4 패킷을 통해 관리 인터페이스로 전달됩니다. 공격자는 스푸핑된 패킷을 사용하여 이 취약성을 악용할 수 있습니다.
이 취약성에는 CVE(Common Vulnerabilities and Exposures) 식별자 CVE-2013-1243이 할당되었습니다.
Cisco IPS NME Malformed IP Packets Denial Of Service 취약성: 이 취약성은 인증 없이 엔드 유저 상호 작용 없이 원격으로 악용될 수 있습니다. 이 취약성을 성공적으로 악용하면 DoS(서비스 거부) 조건이 발생할 수 있습니다. 이 취약성을 악용하려는 시도가 반복되면 DoS 상태가 지속될 수 있습니다. 익스플로잇을 위한 공격 벡터는 관리 인터페이스로 전송된 형식이 잘못된 IP 패킷을 통해 이루어집니다. 공격자는 스푸핑된 패킷을 사용하여 이 취약성을 악용할 수 있습니다.
이 취약성에는 CVE 식별자 CVE-2013-3410이 할당되었습니다.
Cisco IDSM-2 형식이 잘못된 TCP 패킷 서비스 거부 취약성: 이 취약성은 인증 없이 그리고 최종 사용자 상호 작용 없이 원격으로 악용될 수 있습니다. 이 취약성을 성공적으로 악용하면 DoS(서비스 거부) 조건이 발생할 수 있습니다. 이 취약성을 악용하려는 시도가 반복되면 DoS 상태가 지속될 수 있습니다. 익스플로잇을 위한 공격 벡터는 관리 인터페이스로 전송된 형식이 잘못된 TCP 패킷을 통해 이루어집니다. 공격자는 스푸핑된 패킷을 사용하여 이 취약성을 악용할 수 있습니다.
이 취약성에는 CVE 식별자 CVE-2013-3411이 할당되었습니다.
-
취약한 소프트웨어, 영향을 받지 않는 소프트웨어, 고정된 소프트웨어에 대한 정보는 다음 링크에서 확인할 수 있는 Cisco Security Advisory에서 확인할 수 있습니다.
https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20130717-ips
-
Cisco 디바이스는 이러한 취약성에 대한 몇 가지 대응책을 제공합니다. 관리자는 이러한 보호 방법을 인프라 디바이스 및 네트워크를 이동하는 트래픽에 대한 일반적인 보안 모범 사례로 고려하는 것이 좋습니다. 이 문서에서는 이러한 기술에 대한 개요를 제공합니다.
Cisco IOS Software는 다음 방법을 사용하여 효과적인 익스플로잇 방지 수단을 제공할 수 있습니다.- 트랜짓 액세스 제어 목록(tACL)
- uRPF(유니캐스트 역방향 경로 전달)
- IP 소스 가드(IPSG)
uRPF의 올바른 배포 및 구성은 스푸핑된 소스 IP 주소를 사용하는 패킷을 사용하는 공격에 대한 효과적인 보호 방법을 제공합니다. uRPF는 가능한 모든 트래픽 소스에 가깝게 배포해야 합니다.
IPSG의 적절한 구축 및 구성은 액세스 레이어에서 스푸핑 공격을 효과적으로 방어합니다.
Cisco ASA 5500 Series Adaptive Security Appliance, Cisco Catalyst 6500 Series ASASM(ASA Services Module), Cisco Catalyst 6500 Series Switches 및 Cisco 7600 Series Routers용 FWSM(Firewall Services Module)에서도 다음을 사용하여 효과적인 익스플로잇 방지 수단을 제공할 수 있습니다.- tACL
- uRPF
Cisco IOS Software, Cisco ASA, Cisco ASASM 및 Cisco FWSM 방화벽은 show 명령의 출력에 표시된 syslog 메시지 및 카운터 값을 통해 가시성을 제공할 수 있습니다.
또한 Cisco Security Manager는 인시던트, 쿼리 및 이벤트 보고를 통해 가시성을 제공할 수 있습니다.
-
조직은 이러한 취약성의 잠재적 영향을 판단하기 위해 표준 위험 평가 및 완화 프로세스를 따르는 것이 좋습니다. 분류(Triage)란 성공 가능성이 가장 높은 프로젝트를 분류하고 노력을 우선 순위를 정하는 것을 말한다. Cisco는 조직이 정보 보안 팀을 위해 위험 기반 분류 기능을 개발하는 데 도움이 될 문서를 제공했습니다. 보안 취약성 알림에 대한 위험 분류 및 위험 분류 및 프로토타이핑은 조직이 반복 가능한 보안 평가 및 대응 프로세스를 개발하는 데 도움이 될 수 있습니다.
-
주의: 모든 완화 기법의 효과는 제품 혼합, 네트워크 토폴로지, 트래픽 동작, 조직 임무 등 특정 고객 상황에 따라 달라집니다. 모든 컨피그레이션 변경과 마찬가지로, 변경 사항을 적용하기 전에 이 컨피그레이션의 영향을 평가합니다.
완화 및 식별에 대한 구체적인 정보를 다음 장치에 사용할 수 있습니다.Cisco IOS 라우터 및 스위치
완화: 통과 액세스 제어 목록
인터넷 연결 지점, 파트너 및 공급업체 연결 지점 또는 VPN 연결 지점이 포함될 수 있는 인그레스 액세스 지점에서 네트워크로 들어오는 트래픽으로부터 네트워크를 보호하려면 관리자가 tACL(transit access control list)을 구축하여 정책 시행을 수행하는 것이 좋습니다. 관리자는 승인 받은 트래픽만 인그레스 액세스 포인트에서 네트워크에 들어가도록 명시적으로 허용하거나 기존 보안 정책 및 컨피그레이션에 따라 인증 받은 트래픽이 네트워크를 통과하도록 허용하여 tACL을 구성할 수 있습니다. tACL 해결 방법은 공격이 신뢰할 수 있는 소스 주소에서 시작되는 경우 이러한 취약성에 대한 완벽한 보호를 제공할 수 없습니다.
tACL 정책은 영향을 받는 디바이스로 전송되는 무단 IPv4 패킷을 거부합니다. 다음 예에서 192.168.60.0/24은 영향을 받는 디바이스에서 사용하는 IP 주소 공간을 나타내며, 호스트 192.168.100.1은 영향을 받는 디바이스에 액세스해야 하는 신뢰할 수 있는 소스로 간주됩니다. 모든 무단 트래픽을 거부하기 전에 라우팅 및 관리 액세스에 필요한 트래픽을 허용하도록 주의해야 합니다. tACL에 대한 추가 정보가 트랜짓 액세스 제어 목록: 에지에서 필터링에 있습니다.! !-- Include explicit permit statements for trusted sources that !-- require access on management ports ! access-list 150 permit tcp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 22 access-list 150 permit tcp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 80 access-list 150 permit tcp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 443 ! !-- Permit or deny all other Layer 3 and Layer 4 traffic in accordance !-- with existing security policies and configurations ! !-- Explicit deny for all other IP traffic ! access-list 150 deny ip any 192.168.60.0 0.0.0.255 access-list 150 deny ip any any ! !-- Apply tACLs to interfaces in the ingress direction ! interface GigabitEthernet0/0 ip access-group 150 in
인터페이스 액세스 목록으로 필터링하면 ICMP 도달 불가 메시지를 필터링된 트래픽의 소스로 다시 전송합니다. 이러한 메시지를 생성하면 디바이스에서 CPU 사용률이 증가하는 원치 않는 영향을 미칠 수 있습니다. Cisco IOS Software에서 ICMP 연결 불가능 생성은 기본적으로 500밀리초마다 하나의 패킷으로 제한됩니다. ICMP 연결 불가 메시지 생성은 인터페이스 컨피그레이션 명령 no ip unreachable을 사용하여 비활성화할 수 있습니다. ICMP 연결 불가능 속도 제한은 ip icmp rate-limit unreachable interval-in-ms 전역 구성 명령을 사용하여 기본값에서 변경할 수 있습니다.식별: 통과 액세스 제어 목록
관리자가 인터페이스에 tACL을 적용한 후 show ip access-lists 명령은 필터링된 IPv4 패킷의 수를 식별합니다. 관리자는 필터링된 패킷을 조사하여 이러한 취약성을 악용하려는 시도인지 확인하는 것이 좋습니다. show ip access-lists 150에 대한 출력의 예는 다음과 같습니다.router#show ip access-lists 150 Extended IP access list 150 10 permit tcp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 22 20 permit tcp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 80 30 permit tcp host 192.168.100.1 192.168.60.0 0.0.0.255 eq 443 40 deny ip any 192.168.60.0 0.0.0.255 (19 matches) 50 deny ip any any router#
앞의 예에서, 액세스 리스트 150은 ACE(Access Control List Entry) 라인 40에 대해 19개의 IPv 4 패킷을 삭제하였다.
ACE 카운터 및 syslog 이벤트를 사용하여 인시던트를 조사하는 방법에 대한 자세한 내용은 Identifying Incidents Using Firewall and IOS Router Syslog Events Cisco Security Intelligence Operations 백서를 참조하십시오.
관리자는 ACE 카운터 적중과 같은 특정 조건이 충족될 때 Embedded Event Manager를 사용하여 계측을 제공할 수 있습니다. Cisco Security Intelligence Operations 백서 Embedded Event Manager in a Security Context에서는 이 기능을 사용하는 방법에 대한 추가 세부 정보를 제공합니다.ID: 액세스 목록 로깅
log and log-input ACL(access control list) 옵션을 사용하면 특정 ACE와 일치하는 패킷이 로깅됩니다. log-input 옵션은 패킷 소스 및 목적지 IP 주소와 포트 외에 인그레스 인터페이스의 로깅을 활성화합니다.
주의: 액세스 제어 목록 로깅은 CPU를 많이 사용할 수 있으므로 각별한 주의를 기울여 사용해야 합니다. ACL 로깅의 CPU 영향을 제어하는 요소는 로그 생성, 로그 전송, 로그 지원 ACE와 일치하는 패킷을 전달하는 프로세스 스위칭입니다.
Cisco IOS Software의 경우 ip access-list logging interval in-ms 명령은 IPv4 ACL 로깅에 의해 유발되는 프로세스 전환의 효과를 제한할 수 있습니다. logging rate-limit rate-per-second [ except loglevel] 명령은 로그 생성 및 전송의 영향을 제한합니다.
ACL 로깅의 CPU 영향은 Supervisor Engine 720 또는 Supervisor Engine 32를 사용하는 Cisco Catalyst 6500 Series 스위치 및 Cisco 7600 Series 라우터의 하드웨어에서 최적화된 ACL 로깅을 사용하여 해결할 수 있습니다.
ACL 로깅의 컨피그레이션 및 사용에 대한 자세한 내용은 액세스 제어 목록 로깅 이해 Cisco Security Intelligence Operations 백서를 참조하십시오.완화: 스푸핑 보호
유니캐스트 역방향 경로 전달
이 문서에 설명된 취약성은 스푸핑된 IP 패킷으로 악용될 수 있습니다. 관리자는 스푸핑에 대한 보호 메커니즘으로 uRPF(Unicast Reverse Path Forwarding)를 구축하고 구성할 수 있습니다.
uRPF는 인터페이스 레벨에서 구성되며 확인 가능한 소스 IP 주소가 없는 패킷을 탐지하고 삭제할 수 있습니다. 소스 IP 주소에 대한 적절한 반환 경로가 있는 경우 스푸핑된 패킷이 uRPF 지원 인터페이스를 통해 네트워크에 들어갈 수 있으므로 관리자는 uRPF를 사용하여 완벽한 스푸핑 보호를 제공해서는 안 됩니다. 네트워크를 통과하는 합법적인 트래픽을 삭제할 수 있으므로 관리자는 이 기능을 구축하는 동안 적절한 uRPF 모드(느슨하거나 엄격함)가 구성되었는지 확인하는 것이 좋습니다. 엔터프라이즈 환경에서는 사용자 지원 레이어 3 인터페이스의 인터넷 에지 및 내부 액세스 레이어에서 uRPF를 활성화할 수 있습니다.
추가 정보는 Unicast Reverse Path Forwarding Loose Mode 기능 가이드에 있습니다.
uRPF 구성 및 사용에 대한 자세한 내용은 Understanding Unicast Reverse Path Forwarding Cisco Security Intelligence Operations 백서를 참조하십시오.IP Source Guard
IPSG(IP source guard)는 DHCP 스누핑 바인딩 데이터베이스 및 수동으로 구성된 IP 소스 바인딩을 기반으로 패킷을 필터링하여 라우팅되지 않은 레이어 2 인터페이스의 IP 트래픽을 제한하는 보안 기능입니다. 관리자는 IPSG를 사용하여 소스 IP 주소 및/또는 MAC 주소를 위조하여 패킷을 스푸핑하려고 시도하는 공격자의 공격을 방지할 수 있습니다. IPSG를 적절하게 구축하고 구성하면 엄격한 모드 uRPF와 결합하여 이 문서에 설명된 취약성에 대한 가장 효과적인 스푸핑 보호 수단을 제공합니다.
IPSG 구축 및 컨피그레이션에 대한 추가 정보는 DHCP 기능 및 IP 소스 가드 구성에 있습니다.식별: 유니캐스트 역방향 경로 전달을 사용하는 스푸핑 보호
네트워크 인프라 전반에 걸쳐 uRPF가 올바르게 구축 및 구성된 경우 관리자는 show cef interface type slot/port internal, show ip interface, show cef drop, show ip cef switching statistics feature 및 show ip traffic 명령을 사용하여 uRPF가 삭제한 패킷 수를 식별할 수 있습니다 .
참고: Cisco IOS Software Release 12.4(20)T부터 show ip cef switching 명령이 show ip cef switching statistics 기능으로 대체되었습니다.
참고: show 명령 은 | regex 시작 및 show 명령 | include regex 명령 수정자는 다음 예에서 사용되므로 원하는 정보를 보기 위해 관리자가 구문 분석해야 하는 출력의 양을 최소화합니다. 명령 수정자에 대한 자세한 내용은 Cisco IOS Configuration Fundamentals 명령 참조의 show 명령 섹션에 있습니다.router#show cef interface GigabitEthernet 0/0 internal | include drop
ip verify: via=rx (allow default), acl=0, drop=18, sdrop=0 router#
참고: show cef interface type slot/port internal은 CLI에서 완전히 입력해야 하는 숨겨진 명령입니다. 명령 완료를 사용할 수 없습니다.router#show cef drop CEF Drop Statistics Slot Encap_fail Unresolved Unsupported No_route No_adj ChkSum_Err RP 27 0 0 18 0 0 router#
router#show ip interface GigabitEthernet 0/0 | begin verify IP verify source reachable-via RX, allow default, allow self-ping 18 verification drops 0 suppressed verification drops router#
router#show ip cef switching statistics feature IPv4 CEF input features:
앞의 show cef interface type slot/port internal, show cef drop, show ip interface type slot/port show ip cef switching statistics feature, show ip traffic 예제에서 uRPF는 Cisco Express Forwarding의 전달 정보 를 기반으로 하는 IP 패킷의 소스 주소를 확인할 수 없어 uRPF가 구성된 모든 인터페이스에서 전체적으로 수신된 IP 패킷 18개를 삭제했습니다.
Path Feature Drop Consume Punt Punt2Host Gave route
RP PAS uRPF 18 0 0 0 0 Total 18 0 0 0 0 -- CLI Output Truncated -- router# router#show ip traffic | include RPF 18 no route, 18 unicast RPF, 0 forced drop router#Cisco ASA, Cisco ASASM 및 Cisco FWSM 방화벽
완화: 통과 액세스 제어 목록
인터넷 연결 지점, 파트너 및 공급업체 연결 지점 또는 VPN 연결 지점이 포함될 수 있는 인그레스 액세스 지점에서 네트워크로 들어오는 트래픽으로부터 네트워크를 보호하려면 관리자가 tACL을 구축하여 정책 적용을 수행하는 것이 좋습니다. 관리자는 승인 받은 트래픽만 인그레스 액세스 포인트에서 네트워크에 들어가도록 명시적으로 허용하거나 기존 보안 정책 및 컨피그레이션에 따라 인증 받은 트래픽이 네트워크를 통과하도록 허용하여 tACL을 구성할 수 있습니다. tACL 해결 방법은 공격이 신뢰할 수 있는 소스 주소에서 시작되는 경우 이러한 취약성에 대한 완벽한 보호를 제공할 수 없습니다.
tACL 정책은 영향을 받는 디바이스로 전송되는 무단 IPv4 패킷을 거부합니다. 다음 예에서 192.168.60.0/24은 영향을 받는 디바이스에서 사용하는 IP 주소 공간을 나타내며 192.168.100.1의 호스트는 영향을 받는 디바이스에 액세스해야 하는 신뢰할 수 있는 소스로 간주됩니다. 모든 무단 트래픽을 거부하기 전에 라우팅 및 관리 액세스에 필요한 트래픽을 허용하도록 주의해야 합니다.
tACL에 대한 추가 정보가 트랜짓 액세스 제어 목록: 에지에서 필터링에 있습니다.! !-- Include explicit permit statements for trusted sources !-- that require access on the vulnerable protocols and ports ! access-list tACL-Policy extended permit tcp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 22 access-list tACL-Policy extended permit tcp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 80 access-list tACL-Policy extended permit tcp host 192.168.100.1 192.168.60.0 255.255.255.0 eq 443 ! !-- Permit or deny all other Layer 3 and Layer 4 traffic in accordance !-- with existing security policies and configurations ! access-list tACL-Policy extended deny ip any 192.168.60.0 255.255.255.0 ! !-- Explicit deny for all other IP traffic ! access-list tACL-Policy extended deny ip any any ! !-- Apply tACLs to interfaces in the ingress direction ! access-group tACL-Policy in interface outside
식별: 통과 액세스 제어 목록
인터페이스에 tACL이 적용된 후 관리자는 show access-list 명령을 사용하여 필터링된 IPv4 패킷의 수를 식별할 수 있습니다. 관리자는 필터링된 패킷을 조사하여 이러한 취약성을 악용하려는 시도인지 확인하는 것이 좋습니다. show access -list tACL-Policy의 출력 예는 다음과 같습니다.firewall#show access-list tACL-Policy access-list tACL-Policy; 5 elements; name hash: 0x3452703d access-list tACL-Policy line 1 extended permit tcp host 192.168.100.1 192.168.60.0 255.255.255.0 eq ssh (hitcnt=31) access-list tACL-Policy line 2 extended permit tcp host 192.168.100.1 192.168.60.0 255.255.255.0 eq www (hitcnt=11) access-list tACL-Policy line 3 extended permit tcp host 192.168.100.1 192.168.60.0 255.255.255.0 eq https (hitcnt=61) access-list tACL-Policy line 4 extended deny ip any 192.168.60.0 255.255.255.0 (hitcnt=14) access-list tACL-Policy line 5 extended deny ip any any (hitcnt=8)
앞의 예에서 액세스 목록 tACL -Policy는 신뢰할 수 없는 호스트 또는 네트워크에서 받은 14개의 패킷을 삭제했습니다. 또한 syslog 메시지 106023은 소스 및 목적지 IP 주소, 소스 및 목적지 포트 번호, 거부된 패킷에 대한 IP 프로토콜을 포함하는 중요한 정보를 제공할 수 있습니다.식별: 방화벽 액세스 목록 Syslog 메시지
log 키워드가 없는 ACE(Access Control Entry)에서 거부된 패킷에 대해 방화벽 syslog 메시지 106023이 생성됩니다. 이 syslog 메시지에 대한 추가 정보는 Cisco ASA 5500 Series System Log Message, 8.2 - 106023에 있습니다.
Cisco ASA 5500 Series Adaptive Security Appliance용 syslog 구성에 대한 정보는 Monitoring - Configuring Logging에 있습니다. Cisco Catalyst 6500 Series ASA Services Module에서 syslog 구성에 대한 정보는 로깅 구성 에 있습니다. Cisco Catalyst 6500 Series 스위치 및 Cisco 7600 Series 라우터에 대한 FWSM의 syslog 구성에 대한 정보는 Monitoring the Firewall Services Module에 있습니다.
다음 예에서는 show logging | grep regex 명령은 방화벽의 로깅 버퍼에서 syslog 메시지를 추출합니다. 이러한 메시지는 이 문서에 설명된 취약성을 악용하려는 잠재적 시도를 나타낼 수 있는 거부된 패킷에 대한 추가 정보를 제공합니다. 로깅된 메시지에서 특정 데이터를 검색하기 위해 grep 키워드와 다른 정규식을 사용할 수 있습니다.
정규식 구문에 대한 추가 정보는 정규식 만들기에 있습니다.firewall#show logging | grep 106023 Jul 10 2013 00:15:13: %ASA-4-106023: Deny tcp src outside:192.0.2.200/2945 dst inside:192.168.60.33/ssh by access-group "tACL-Policy" Jul 10 2013 00:15:13: %ASA-4-106023: Deny tcp src outside:192.0.2.99/2946 dst inside:192.168.60.240/www by access-group "tACL-Policy" Jul 10 2013 00:15:13: %ASA-4-106023: Deny tcp src outside:192.0.2.100/2947 dst inside:192.168.60.115/https by access-group "tACL-Policy" firewall#
앞의 예에서 tACL tACL 정책에 대해 로깅된 메시지는 인프라 디바이스에 할당된 주소 블록으로 전송된 스푸핑된 잠재적 패킷을 보여줍니다.
Cisco ASA Series Adaptive Security Appliance용 syslog 메시지에 대한 추가 정보는 Cisco ASA 5500 Series System Log Messages, 8.2에 있습니다. Cisco Catalyst 6500 Series ASA Services Module의 syslog 메시지에 대한 추가 정보는 Cisco ASASM CLI 컨피그레이션 가이드의 Analyzing Syslog Messages 섹션에 있습니다. Cisco FWSM용 syslog 메시지에 대한 추가 정보는 Catalyst 6500 Series Switch 및 Cisco 7600 Series Router Firewall Services Module Logging System Log Messages에 있습니다.
syslog 이벤트를 사용한 인시던트 조사에 대한 자세한 내용은 Identifying Incidents Using Firewall and IOS Router Syslog Events Cisco Security Intelligence Operations 백서를 참조하십시오.
완화: 유니캐스트 역방향 경로 전달을 사용한 스푸핑 보호
이 문서에 설명된 취약성은 스푸핑된 IP 패킷으로 악용될 수 있습니다. 관리자는 스푸핑에 대한 보호 메커니즘으로 uRPF를 구축하고 구성할 수 있습니다.
uRPF는 인터페이스 레벨에서 구성되며 확인 가능한 소스 IP 주소가 없는 패킷을 탐지하고 삭제할 수 있습니다. 소스 IP 주소에 대한 적절한 반환 경로가 있는 경우 스푸핑된 패킷이 uRPF 지원 인터페이스를 통해 네트워크에 들어갈 수 있으므로 관리자는 uRPF를 사용하여 완벽한 스푸핑 보호를 제공해서는 안 됩니다. 엔터프라이즈 환경에서는 인터넷 에지와 사용자 지원 레이어 3 인터페이스의 내부 액세스 레이어에서 uRPF를 활성화할 수 있습니다.
uRPF의 컨피그레이션 및 사용에 대한 자세한 내용은 ip verify reverse-path에 대한 Cisco Security Appliance Command Reference 및 Understanding Unicast Reverse Path Forwarding Cisco Security Intelligence Operations 백서를 참조하십시오.식별: 유니캐스트 역방향 경로 전달을 사용하는 스푸핑 보호
uRPF에서 거부된 패킷에 대해 방화벽 syslog 메시지 106021이 생성됩니다. 이 syslog 메시지에 대한 추가 정보는 Cisco ASA 5500 Series System Log Message, 8.2 - 106021에 있습니다.
Cisco ASA 5500 Series Adaptive Security Appliance용 syslog 구성에 대한 정보는 Monitoring - Configuring Logging에 있습니다. Cisco Catalyst 6500 Series ASA Services Module에 대한 syslog 구성 정보는 로깅 구성에 있습니다. Cisco Catalyst 6500 Series 스위치 및 Cisco 7600 Series 라우터에 대한 FWSM의 syslog 구성에 대한 정보는 Monitoring the Firewall Services Module에 있습니다.
다음 예에서는 show logging | grep regex 명령은 방화벽의 로깅 버퍼에서 syslog 메시지를 추출합니다. 이러한 메시지는 이 문서에 설명된 취약성을 악용하려는 잠재적 시도를 나타낼 수 있는 거부된 패킷에 대한 추가 정보를 제공합니다. 로깅된 메시지에서 특정 데이터를 검색하기 위해 grep 키워드와 다른 정규식을 사용할 수 있습니다.
정규식 구문에 대한 추가 정보는 정규식 만들기에 있습니다.firewall#show logging | grep 106021 Jul 10 2013 00:15:13: %ASA-1-106021: Deny TCP reverse path check from 192.168.60.1 to 192.168.60.100 on interface outside Jul 10 2013 00:15:13: %ASA-1-106021: Deny TCP reverse path check from 192.168.60.1 to 192.168.60.100 on interface outside Jul 10 2013 00:15:13: %ASA-1-106021: Deny UDP reverse path check from 192.168.60.1 to 192.168.60.100 on interface outside
다음 예와 같이 show asp drop 명령은 uRPF 기능이 삭제한 패킷의 수를 식별할 수도 있습니다.firewall#show asp drop frame rpf-violated Reverse-path verify failed 11 firewall#
앞의 예에서 uRPF는 uRPF가 구성된 인터페이스에서 수신된 11개의 IP 패킷을 삭제했습니다. 출력이 없으면 방화벽의 uRPF 기능에서 패킷이 삭제되지 않았음을 나타냅니다.
가속화된 보안 경로 삭제 패킷 또는 연결 디버깅에 대한 자세한 내용은 Cisco Security Appliance Command Reference for show asp drop을 참조하십시오.Cisco 보안 관리자
식별: Cisco Security Manager
소프트웨어 버전 4.0부터 Cisco Security Manager는 Cisco 방화벽 및 Cisco IPS 디바이스에서 syslog를 수집하고 이 문서에 설명된 취약성과 관련된 이벤트를 쿼리할 수 있는 이벤트 뷰어를 제공합니다. 이벤트 뷰어의 미리 정의된 방화벽 거부 이벤트 보기에서 다음 필터를 사용하면 이 문서에 설명된 취약성을 악용하려는 잠재적인 시도를 나타낼 수 있는 모든 캡처된 Cisco 방화벽 액세스 목록 거부 syslog 메시지를 제공합니다.- Destination 이벤트 필터를 사용하여 영향을 받는 디바이스에서 사용하는 IP 주소 공간을 포함하는 네트워크 객체를 필터링합니다(예: IPv4 주소 범위 192.168.60.0/24)
- ASA-4-106021(uRPF 스푸핑)
- ASA-4-106023(ACL 거부)
ID: Event Management System 파트너 이벤트
Cisco는 Cisco Developer Network를 통해 업계 최고의 SIEM(Security Information and Event Management) 기업과 협력하고 있습니다. 이러한 파트너십을 통해 Cisco는 장기 로그 아카이빙 및 포렌식, 이기종 이벤트 상관관계, 고급 규정 준수 보고 등 비즈니스 문제를 해결하는 검증된 SIEM 시스템을 제공할 수 있습니다. Security Information and Event Management 파트너 제품을 활용하여 Cisco 디바이스에서 이벤트를 수집한 다음 수집된 이벤트에서 Cisco IPS 시그니처로 생성된 사고를 쿼리하거나, 이 문서에 설명된 취약성을 악용하려는 잠재적인 시도를 나타낼 수 있는 방화벽의 syslog 메시지를 거부할 수 있습니다. 쿼리는 다음 목록에 표시된 것처럼 Sig ID 및 Syslog ID로 수행할 수 있습니다.- ASA-4-106021(uRPF 스푸핑)
- ASA-4-106023(ACL 거부)
-
이 문서는 "있는 그대로" 제공되며, 상품성 또는 특정 사용에 대한 적합성의 보증을 포함하여 어떤 종류의 보장 또는 보증도 의미하지 않습니다. 문서 또는 문서에 링크된 자료의 정보를 사용하는 것은 귀하의 책임입니다. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
-
Cisco 제품의 보안 취약성 보고, 보안 사고에 대한 지원 요청, Cisco의 보안 정보 수신을 위한 등록 등에 대한 자세한 내용은 Cisco의 전 세계 웹 사이트(https://sec.cloudapps.cisco.com/security/center/resources/security_vulnerability_policy.html)에서 확인할 수 있습니다. 여기에는 Cisco 보안 알림과 관련된 언론 문의에 대한 지침이 포함됩니다. 모든 Cisco 보안 권고 사항은 http://www.cisco.com/go/psirt에서 확인할 수 있습니다.
-
보안 취약성은 다음과 같은 제품 조합에 적용됩니다.
기본 제품 Cisco IPS(Intrusion Prevention System) 5.0(1), (2), (3), (4), (5), (6) | 5.1 ((1), (1a), (1b), (1c), (1d), (1e), (p1), (2), (5), (6) | 6.0(기본, (2), (3), (4)) | 6.1(기본) | 7.0(기본) | 7.1(기본)
관련 제품
-
이 문서는 "있는 그대로" 제공되며, 상품성 또는 특정 사용에 대한 적합성의 보증을 포함하여 어떤 종류의 보장 또는 보증도 의미하지 않습니다. 문서 또는 문서에 링크된 자료의 정보를 사용하는 것은 귀하의 책임입니다. CISCO는 언제든지 알림을 변경하거나 업데이트할 수 있는 권리를 보유합니다.
배포 URL을 생략하는 이 문서의 텍스트를 독립 실행형으로 복사하거나 패러프레이즈는 관리되지 않는 복사본이며 중요한 정보가 없거나 사실 오류가 있을 수 있습니다. 이 문서의 정보는 Cisco 제품의 최종 사용자를 대상으로 합니다