본 제품에 대한 문서 세트는 편견 없는 언어를 사용하기 위해 노력합니다. 본 설명서 세트의 목적상, 편견 없는 언어는 나이, 장애, 성별, 인종 정체성, 민족 정체성, 성적 지향성, 사회 경제적 지위 및 교차성에 기초한 차별을 의미하지 않는 언어로 정의됩니다. 제품 소프트웨어의 사용자 인터페이스에서 하드코딩된 언어, RFP 설명서에 기초한 언어 또는 참조된 서드파티 제품에서 사용하는 언어로 인해 설명서에 예외가 있을 수 있습니다. 시스코에서 어떤 방식으로 포용적인 언어를 사용하고 있는지 자세히 알아보세요.
Cisco는 전 세계 사용자에게 다양한 언어로 지원 콘텐츠를 제공하기 위해 기계 번역 기술과 수작업 번역을 병행하여 이 문서를 번역했습니다. 아무리 품질이 높은 기계 번역이라도 전문 번역가의 번역 결과물만큼 정확하지는 않습니다. Cisco Systems, Inc.는 이 같은 번역에 대해 어떠한 책임도 지지 않으며 항상 원본 영문 문서(링크 제공됨)를 참조할 것을 권장합니다.
이 문서에서는 Catalyst 9600 Supervisor 및 라인 카드의 하드웨어 장애 증상을 식별, 격리 및 트러블슈팅하는 방법에 대해 설명합니다.
이 문서에 대한 특정 요건이 없습니다.
이 문서의 정보는 Catalyst 9600 Series 스위치를 기반으로 합니다.
이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 이 문서에 사용된 모든 디바이스는 초기화된(기본) 컨피그레이션으로 시작되었습니다. 현재 네트워크가 작동 중인 경우 모든 명령의 잠재적인 영향을 미리 숙지하시기 바랍니다.
용어 |
정의 |
컨텍스트 |
수퍼바이저 |
Cisco Catalyst 9600 Series Supervisor Engine 1은 3개의 UADP 3.0 ASIC와 1개의 x86 CPU 프로세서로 구동됩니다. 3개의 ASIC는 각 ASIC에서 3.2Tbps ASIC 상호 연결을 사용하여 상호 연결됩니다. Sup-1은 9.6Tbps(4.8Tbps 전이중)를 제공합니다. Cisco Catalyst 9606R 섀시를 사용할 경우 각 슬롯에는 Sup-1이 포함된 2.4Tbps가 있습니다. |
이 문서에는 수퍼바이저 엔진의 하드웨어 장애를 격리하는 명령이 포함되어 있습니다. |
Power On Self Test(P.O.S.T.) |
전원을 켠 후 수퍼바이저 및 라인 카드가 초기화되면 POST(Power On Self Test)가 실행되어 모듈의 하드웨어 무결성을 보장합니다. POST는 라인 카드의 OIR(Online Insertion & Removal) 중에 실행됩니다. |
Show post 명령은 이러한 테스트의 결과를 표시합니다. |
일반 온라인 진단 하위 시스템(GOLD) |
GOLD 테스트는 시스템이 온라인 상태가 된 후에 실행됩니다. 일부 테스트는 정기적으로 상태 모니터링 테스트로 실행됩니다. 모든 테스트는 사용자가 온디맨드 방식으로 실행할 수 있습니다. |
모듈 하드웨어 장애를 탐지하는 데 사용됩니다. |
온라인 삽입 및 제거 (O.I.R.) |
이 기능은 CLI(Command Line Interface)를 통해 지정된 슬롯에서 모듈의 전원을 껐다가 다시 켤 수 있습니다. 이 기능은 물리적으로 모듈을 재장착할 수 있는 현장 리소스가 없는 경우에 유용합니다. |
O.I.R은 모듈에서 하드웨어 장애를 격리하는 뛰어난 기능입니다. |
Catalyst C9606-R |
|
![]() |
증상 |
가능한 근본 원인 |
|
모듈이 제대로 설치되지 않았거나 초기화되지 않았거나 P.O.S.T. 실패 때문에 하드웨어 오류가 발생했습니다. |
모듈 상태 |
가능한 근본 원인 |
작업 |
확인 |
해당 없음. |
없음 |
탈락 |
잠재적 하드웨어 장애. |
모듈 상태 문제 해결을 참조하십시오. |
기타 |
모듈을 초기화하지 못했습니다. |
모듈 상태 문제 해결을 참조하십시오. |
출력에 나열되지 않음 |
제대로 설치되지 않았거나 충분한 전원을 공급받지 못했습니다. |
사용 가능한 전력 예산을 확인합니다. 모듈의 L.E.D. 상태를 시각적으로 검사합니다. |
Cat9600#show module Chassis Type: C9606R Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+--------------+-------------- 1 24 24-Port 40GE/12-Port 100GE C9600-LC-24C 2 48 48-Port 10GE / 25GE C9600-LC-48YL 3 0 Supervisor 1 Module C9600-SUP-1 4 0 Supervisor 1 Module C9600-SUP-1 Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.0 17.1.1[FC2] 16.12.03 post-fail 2 DC8C.3773.1E00 to DC8C.3773.1E7F 1.0 17.1.1[FC2] 16.12.03 ok 3 DC8C.379F.ED80 to DC8C.379F.EDFF 1.0 17.1.1[FC2] 16.12.03 ok 4 DC8C.379F.EDF1 to DC8C.379F.EDF9 1.0 17.1.1[FC2] 16.12.03 ok //other example Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.3 17.3.1r[FC2] 17.03.05 power-deny 2 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.3 17.3.1r[FC2] 17.03.05 power-deny 3 DC8C.37A0.C880 to DC8C.37A0.C8FF 1.4 17.3.1r[FC2] 17.03.05 ok
증상 |
작업 |
모듈이 나열되지 않거나 상태가 '확인'이 아닙니다. |
다음 단계를 진행합니다. |
Syslog 확인
라인 카드 오프라인
%IOSXE_OIR-6-OFFLINECARD: Card (rp) offline in slot R1 %IOSXE_OIR-6-REMSPA: SPA removed from subslot 6/0, interfaces disabled %SPA_OIR-6-OFFLINECARD: SPA (C9600-LC-48TX) offline in subslot 6/0
전력 예산 문제
%CMRP_PFU-3-PWR_MGMT_LC_SHUTDOWN: R0/0: cmand: WARNING: Linecard in slot 6 with priority 0 and a power requirement of 315 watts has shutdown. %CMRP_PFU-3-PWR_MGMT_ALARM: Chassis 1 R0/0: cmand: WARNING: System does not have sufficient input power for minimum reliable operation requiring 1161 watts. The system needs 1101 watts of additional power.
진단 테스트 실패
*May 29 02:10:19.523: %PM-4-ERR_DISABLE: diagnostics error detected on Fo2/0/1, putting Fo2/0/1 in err-disable state
모듈 가동 시간 확인
Cat9600#show logging onboard rp (active|standby) uptime detail
-------------------------------------------------------------------------------- UPTIME SUMMARY INFORMATION -------------------------------------------------------------------------------- First customer power on : 08/28/2021 13:08:41 Total uptime : 0 years 41 weeks 2 days 15 hours 10 minutes <-- Total Uptime Total downtime : 0 years 7 weeks 6 days 7 hours 11 minutes Number of resets : 14 <-- Total number of resets Number of slot changes : 0 Current reset reason : PowerOn <-- Last reload reason Current reset timestamp : 11/06/2021 17:25:29 Current slot : 3 Chassis type : 55 Current uptime : 0 years 39 weeks 1 days 18 hours 5 minutes <-- Current Uptime -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- UPTIME CONTINUOUS INFORMATION -------------------------------------------------------------------------------- Time Stamp | Reset | Uptime MM/DD/YYYY HH:MM:SS | Reason | years weeks days hours minutes -------------------------------------------------------------------------------- 08/28/2021 13:08:41 PowerOn 0 0 0 0 0 08/28/2021 13:16:29 Reload 0 0 0 0 0 08/28/2021 13:29:28 Reload 0 0 0 0 5 08/28/2021 13:42:30 Reload 0 0 0 0 5 08/28/2021 13:55:14 Image Install 0 0 0 0 5 <-- Reset history by reason
Cat9600#show logging onboard slot (1|2|4|5|6|7) uptime detail -------------------------------------------------------------------------------- UPTIME SUMMARY INFORMATION -------------------------------------------------------------------------------- First customer power on : 08/08/2018 09:30:33 Total uptime : 0 years 11 weeks 1 days 10 hours 40 minutes Total downtime : 4 years 32 weeks 1 days 23 hours 25 minutes Number of resets : 81 Number of slot changes : 5 Current reset reason : CP_RESET_CPU_GOT_RESET Current reset timestamp : 05/24/2023 19:35:58 Current slot : 1 Chassis type : 30 Current uptime : 0 years 2 weeks 0 days 0 hours 0 minutes -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- UPTIME CONTINUOUS INFORMATION -------------------------------------------------------------------------------- Time Stamp | Reset | Uptime MM/DD/YYYY HH:MM:SS | Reason | years weeks days hours minutes -------------------------------------------------------------------------------- 04/26/2021 21:39:45 CP_RESET_CPU_GOT_RESET 0 0 0 0 0 04/27/2021 14:12:04 CP_RESET_POWER_ON 0 0 0 6 0 04/28/2021 14:39:30 CP_RESET_POWER_ON 0 0 0 14 0 04/30/2021 12:46:59 CP_RESET_POWER_ON 0 0 0 13 0
다음을 확인합니다. POST
실패한 POST 예
Cat9600#show post
Stored system POST messages:
Switch C9606R
--------------
Fri May 29 02:10:18 2020 POST: Module: 1 Mac Loopback Begin
Fri May 29 02:10:18 2020 POST: Module: 1 Mac Loopback: loopback Test: End, Status Passed
Fri May 29 02:10:18 2020 POST: Module: 2 Mac Loopback Begin
Fri May 29 02:10:18 2020 POST: Mac Loopback: Failed For Interface : TwentyFiveGigE2/2/0/38
Fri May 29 02:10:18 2020 POST: Mac Loopback: Failed For Interface : TwentyFiveGigE2/2/0/39
Fri May 29 02:10:18 2020 POST: Mac Loopback: Failed For Interface : TwentyFiveGigE2/2/0/40
Fri May 29 02:10:18 2020 POST: Module: 2 Mac Loopback: loopback Test: End, Status Failed
POST 통과 예
Cat9600#show post Stored system POST messages: Switch C9606R -------------- POST: MBIST Tests : Begin POST: MBIST Tests : End, Status Passed POST: Module: 3 PHY Loopback: loopback Test: Begin POST: Module: 3 PHY Loopback: loopback Test: End, Status Passed POST: Module: 2 PHY Loopback: loopback Test: Begin POST: Module: 2 PHY Loopback: loopback Test: End, Status Passed POST: Module: 1 PHY Loopback: loopback Test: Begin POST: Module: 1 PHY Loopback: loopback Test: End, Status Passed POST: Module: 5 PHY Loopback: loopback Test: Begin POST: Module: 5 PHY Loopback: loopback Test: End, Status Passed
Cat9600#show platform Chassis type: C9606R Slot Type State Insert time (ago) --------- ------------------- --------------------- ----------------- 1 C9600-LC-24C ok 02:45:09 1/0 C9600-LC-24C ok 02:43:15 2 C9600-LC-48YL faulty 02:45:09 2/0 C9600-LC-48YL ok 02:43:14 3 C9600-SUP-1 ok 02:45:09 3/0 C9600-SUP-1 ok 02:43:14 4 C9600-SUP-1 ok 02:45:09 4/0 C9600-SUP-1 ok 02:43:14 R0 C9600-SUP-1 ok, active 02:45:09 R1 C9600-SUP-1 init, standby 02:45:09 P1 C9600-PWR-2KWAC ok 02:44:21 P2 C9600-PWR-2KWAC ok 02:44:21 P3 C9600-PWR-2KWAC ps, f0, f1, fail 02:44:21 P4 C9600-PWR-2KWAC ps, f0, f1, fail 02:44:21 P5 C9606-FAN ok 02:44:21 Slot CPLD Version Firmware Version --------- ------------------- --------------------------------------- 1 19070619 17.1.1[FC2] 2 19070619 17.1.1[FC2] 3 19041620 17.1.1[FC2] 4 19041620 17.1.1[FC2]
진단 테스트 유형:
진단 테스트 |
테스트 대상 상황? 영향? |
TestGoldPkt루프백 |
이 테스트는 Macloopback 테스트와 매우 유사합니다. |
테스트OBFL |
온보드 장애 로깅 기능을 확인합니다. 이 테스트는 진단 메시지를 인쇄하고 OBFL에 기록됩니다. |
테스트 열 |
센서의 온도 값이 임계값을 초과하지 않는지 확인합니다. 무중단 테스트이며 상태 모니터 테스트로 실행할 수 있습니다. |
테스트 포트Tx모니터링 |
이 테스트에서는 연결된 인터페이스의 TX 카운터를 모니터링합니다. 이 테스트에서는 연결된 포트에서 패킷을 전송할 수 있는지 여부를 확인합니다. 무중단 테스트이며 상태 모니터링 테스트로 실행할 수 있습니다. |
팬 트레이 테스트 |
이 테스트에서는 팬 트레이가 삽입되었으며 보드에서 제대로 작동하는지 확인합니다. 무중단 테스트이며 상태 모니터링 테스트로 실행할 수 있습니다. |
테스트 스크래치 레지스터 |
스크래치 레지스터 테스트는 ASIC(Application-Specific Integrated Circuits)의 상태를 모니터링하며, 이 ASIC는 레지스터에 값을 쓰고 이러한 레지스터에서 값을 다시 읽습니다. 무중단 테스트이며 상태 모니터링 테스트로 실행할 수 있습니다. |
테스트 일관성 검사 멀티캐스트 |
이 테스트는 Mcast 프로그래밍이 올바른지 여부를 모니터링합니다. 이 테스트에서는 Forwarding object manger와 함께 하드웨어에 대한 불완전한 항목이나 장기 보류 중인 컨피그레이션을 확인합니다. |
모듈에 대해 온디맨드 진단 테스트를 실행합니다.
Cat9600#diagnostic start switch module 3 test ?
Diagnostics test suite attributes:
M/C/* - Minimal bootup level test / Complete bootup level test / NA
B/* - Basic ondemand test / NA
P/V/* - Per port test / Per device test / NA
D/N/* - Disruptive test / Non-disruptive test / NA
S/* - Only applicable to standby unit / NA
X/* - Not a health monitoring test / NA
F/* - Fixed monitoring interval test / NA
E/* - Always enabled monitoring test / NA
A/I - Monitoring is active / Monitoring is inactive
Test Interval Thre-
ID Test Name Attributes day hh:mm:ss.ms shold
==== ================================== ============ =============== =====
1) TestOBFL ------------------------> *B*N*X**I not configured n/a
2) TestFantray ---------------------> *B*N****A 000 00:01:40.00 1
3) TestThermal ---------------------> *B*N****A 000 00:01:30.00 1
4) TestScratchRegister -------------> *B*N****A 000 00:01:30.00 5
5) TestConsistencyCheck ------------> *B*N****A 000 00:01:30.00 1
WORD Test ID list (e.g. 1,3-6) or Test Name
Cat9600#diagnostic start switch 1 module 3 test 2
//syslog prints upon start and finish of diagnostic test.
*Mar 24 21:48:47.968: %DIAG-6-TEST_RUNNING: switch 1 module 3: Running TestFantray{ID=2} ...
*Mar 24 21:48:47.969: %DIAG-6-TEST_OK: switch 1 module 3: TestFantray{ID=2} has completed successfully <-- Passed
증상 |
작업 |
모듈이 진단 테스트에 실패했습니다. |
모듈의 수술실 검사 실시 |
모듈에서 온디맨드 OIR 실행
Cat9600#hw-module subslot 1/0 oir power-cycle
Proceed with power cycle of module? [confirm]
*Jun 9 20:39:14.686: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 1/0, interfaces disabled
*Jun 9 20:39:14.721: %SPA_OIR-6-OFFLINECARD: SPA (C9600-LC-24C) offline in subslot 1/0
*Jun 9 20:39:16.686: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/1, changed state to down
*Jun 9 20:39:16.686: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/2, changed state to down
*Jun 9 20:39:16.687: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/3, changed state to down
*Jun 9 20:39:16.687: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/4, changed state to down
*Jun 9 20:39:16.689: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/5, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/6, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/7, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/8, changed state to down
*Jun 9 20:39:16.690: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/9, changed state to down
*Jun 9 20:39:16.691: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/10, changed state to down
*Jun 9 20:39:16.691: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/11, changed state to down
*Jun 9 20:39:16.693: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/12, changed state to down
*Jun 9 20:39:16.693: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/13, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/14, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/15, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/16, changed state to down
*Jun 9 20:39:16.694: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/17, changed state to down
*Jun 9 20:39:16.695: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/18, changed state to down
*Jun 9 20:39:16.695: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/19, changed state to down
*Jun 9 20:39:16.697: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/20, changed state to down
*Jun 9 20:39:16.697: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/21, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/22, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/23, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface FortyGigabitEthernet1/0/24, changed state to down
*Jun 9 20:39:16.698: %LINK-3-UPDOWN: Interface HundredGigE1/0/25, changed state to down
*Jun 9 20:39:16.699: %LINK-3-UPDOWN: Interface HundredGigE1/0/26, changed state to down
*Jun 9 20:39:16.699: %LINK-3-UPDOWN: Interface HundredGigE1/0/27, changed state to down
*Jun 9 20:39:16.701: %LINK-3-UPDOWN: Interface HundredGigE1/0/28, changed state to down
*Jun 9 20:39:16.701: %LINK-3-UPDOWN: Interface HundredGigE1/0/29, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/30, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/31, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/32, changed state to down
*Jun 9 20:39:16.702: %LINK-3-UPDOWN: Interface HundredGigE1/0/33, changed state to down
*Jun 9 20:39:16.703: %LINK-3-UPDOWN: Interface HundredGigE1/0/34, changed state to down
*Jun 9 20:39:16.703: %LINK-3-UPDOWN: Interface HundredGigE1/0/35, changed state to down
*Jun 9 20:39:16.704: %LINK-3-UPDOWN: Interface HundredGigE1/0/36, changed state to down
*Jun 9 20:39:16.704: %LINK-3-UPDOWN: Interface HundredGigE1/0/37, changed state to down
*Jun 9 20:39:16.705: %LINK-3-UPDOWN: Interface HundredGigE1/0/38, changed state to down
*Jun 9 20:39:16.705: %LINK-3-UPDOWN: Interface HundredGigE1/0/39, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/40, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/41, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/42, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/43, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/44, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/45, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/46, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/47, changed state to down
*Jun 9 20:39:16.713: %LINK-3-UPDOWN: Interface HundredGigE1/0/48, changed state to down
*Jun 9 20:39:44.717: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 1/0
*Jun 9 20:40:15.052: %SPA_OIR-6-ONLINECARD: SPA (C9600-LC-24C) online in subslot 1/0
*interfaces come up again*
증상 |
작업 |
모듈이 여전히 P.O.S.T에 실패하거나 show module 또는 show inventory 명령 출력에 나열되지 않은 모듈입니다. |
|
모듈을 재장착합니다(섀시에서 모듈을 인식하고 모듈이 초기화되면 유사한 syslog가 인쇄됨).
*May 24 19:32:53.084: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0 *May 24 19:32:53.084: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 1 *May 24 19:32:53.084: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 1 *May 24 19:32:53.151: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 1/0
모듈의 전원 상태가 승인되었는지 확인합니다.
Cat9600#show power module Power Budget Mode : Dual Sup Power Out of In Mod Model No State Budget Instantaneous Peak Reset Reset --- -------------------- -------- ------ ------------- ---- ------ ----- 1 C9600-LC-48YL accepted 230 0 0 230 10 2 C9600-LC-24C accepted 200 0 0 200 10 3 C9600-SUP-1 accepted 775 0 0 775 202 4 C9600-SUP-1 accepted 775 0 0 775 202 FM1 C9606-FAN accepted 450 -- -- 450 -- --- -------------------- -------- ------ ------------- ---- ------ ----- Total allocated power: 2430 Total required power: 2430
장애가 발생한 전원 공급 장치가 있는지 확인합니다.
Cat9600#show power detail Power Fan States Supply Model No Type Capacity Status 1 2 ------ -------------------- ---- -------- ------------ ----------- PS1 C9600-PWR-2KWAC ac 1050 W active good good PS2 C9600-PWR-2KWAC ac 2000 W active good good PS3 C9600-PWR-2KWAC ac n.a. fail bad bad PS4 C9600-PWR-2KWAC ac n.a. fail bad bad PS Current Configuration Mode : none PS Current Operating State : none Power supplies currently active : 2 Power supplies currently available : 4 Power Summary Maximum (in Watts) Used Available ------------- ------ --------- System Power 2905 2990 ------------- ------ --------- Total 2905 2990 <-- total power budget consumed vs maximum available Power Budget Mode : Dual Sup Power Out of In Mod Model No State Budget Instantaneous Peak Reset Reset --- -------------------- -------- ------ ------------- ---- ------ ----- 1 C9600-LC-48TX accepted 315 0 0 315 10 2 C9600-LC-48S accepted 160 0 0 160 10 3 C9600-SUP-1 accepted 775 0 0 775 202 4 C9600-SUP-1 --- 775 -- -- 775 0 5 C9600-LC-48YL accepted 230 0 0 230 10 6 C9600-LC-24C accepted 200 0 0 200 10 FM1 C9606-FAN accepted 450 -- -- 450 -- --- -------------------- -------- ------ ------------- ---- ------ ----- Total allocated power: 2905 Total required power: 2905
참고: 수퍼바이저의 펌웨어/부트 로더를 수동으로 업그레이드하는 방법에 대한 자세한 내용은 Catalyst 9600 Series Switches Cisco IOS XE Amsterdan 17.3.X 릴리스 정보를 참조하십시오.
Cat9600#show firmware version all Current Bundled Slot Device Name / Model Firmware Version Firmware Version Mismatch ----- ----------------------------- --------------------- ------------------- --------- 3 Supervisor Rommon (Active) 17.3.1r[FC2] N/A N/A <-- Firmware versions are the same 4 Supervisor Rommon (Standby) 17.3.1r[FC2] N/A N/A <-- Firmware versions are the same - Eth Lan Spi 0x800005d3 N/A N/A PS5 Fantray 18101008 N/A N/A 3 Supervisor CPLD IO FPGA 19041620 19041620 No Flash FPGA 190308b9 190308b9 No 4 Supervisor CPLD IO FPGA 19041620 19041620 No Flash FPGA 190308b9 190308b9 No 1 Line Card / C9600-LC-24C IO FPGA 19070619 19070619 No PMFPGA 122515 N/A N/A Phy Firmware 1.56.1772 1.56.2270 Yes 2 Line Card / C9600-LC-48YL IO FPGA 19070619 19070619 No PMFPGA 122515 N/A N/A Phy Firmware 1.56.1772 1.56.2270 Yes 5 Line Card / C9600-LC-48YL IO FPGA 19070619 19070619 No PMFPGA 122515 N/A N/A Phy Firmware 1.56.1772 1.56.2270 Yes 6 Line Card / C9600-LC-24C IO FPGA 19070619 19070619 No PMFPGA 122515 N/A N/A Phy Firmware 1.56.1772 1.56.2270 Yes Slot Device Name / Model Firmware Version --------- --------------------------------------- ----------------------------- PS1 Power Supply (PS PRI, PS_SEC, PS_I2C) (N/A, N/A, N/A) PS2 Power Supply (PS PRI, PS_SEC, PS_I2C) (N/A, N/A, N/A) PS3 Power Supply (PS PRI, PS_SEC, PS_I2C) (N/A, N/A, N/A) PS4 Power Supply (PS PRI, PS_SEC, PS_I2C) (61.08.03, 61.02.0, N/A)
참고: 하드웨어 인증 상태는 스위치를 다시 로드할 때만 실행됩니다. 동일한 슬롯 또는 다른 슬롯에서 라인 카드를 물리적으로 재장착한 후에는 실행되지 않으며, 반드시 문제가 발생하지는 않습니다.
라인 카드가 있는 경우 인증 상태가 NOT PASS인 경우 다음 권장 단계를 실행합니다.
Cat9600#show platform hardware authentication status Fan Tray Authentication: pass Line Card:1 Authentication: pass Line Card:2 Authentication: pass SUP0 Authentication: pass SUP1 Authentication: pass Line Card:5 Authentication: Not Available Line Card:6 Authentication: Not Available
Cat9600#show hw-module subslot 1/0 oir internal IOMD for supervisor slot does not appear WARNING: This command is not intended for production use and should only be used under the supervision of Cisco Systems technical support personnel. sm(spa_oir_tsm subslot 1/0 TSM), running yes, state ready Admin Status: admin enabled, Operational Status: ok(1) Last reset Reason: power up TSM Context: configured_spa_type 0xD9A <-- IDPROM is accessible soft remove fail code 0x0(none) last_fail_code 0x0(none) timed_fail_count 0, failed_spa_type 0x0 flags 0x10) Subslot: spa type 0xD9A, active spa type 0xD9A subslot flags 0x0, plugin flags 0x0 TSM Parameters: wait_psm_ready_timeout 540000 ms, init_timeout 300000 ms remove_timeout 120000 ms, recovery_delay 5000 ms fail_time_period 1200000 ms, max_fail_count 5 does not support pre-configuration
Cat9600# show platform software iomd redundancy Configured Redundancy Mode = sso Operating Redundancy Mode = sso Local RF state = ACTIVE Peer RF state = STANDBY HOT slot PSM STATE SPA INTF HA_STATE HA_ACTIVE 1 ready started ready 00:05:54 2 ready idle <-- potential issue 3 ready started ready 00:05:37 ***active RP 4 ready started ready 00:05:37
Cat9600#show idprom module 1 eeprom detail Slot 1 EEPROM data: EEPROM version : 4 Compatible Type : 0xFF Controller Type : 3482 Hardware Revision : 1.0 PCB Part Number : 73-19545-02 Board Revision : A0 Deviation Number : 0 Fab Version : 02 PCB Serial Number : CAT2313L2VP RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Top Assy. Part Number : 068-102161-01 Top Assy. Revision : A0 CLEI Code : COUIBGRCAA Product Identifier (PID) : C9600-LC-24C Version Identifier (VID) : V01 Base MAC Address : DC 8C 37 A0 C8 80 MAC Address block size : 128 Environment Monitor Data : 06 00 00 00 0C 80 C8 00 A6 Environment Monitor Data : 00 06 00 FA Manufacturing Test Data : 00 00 00 00 00 00 00 00 Field Diagnostics Data : 00 00 00 00 00 00 00 00 Platform features : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Environment Monitor Data : Description : InltFrnt Shutdown threshold : 060 Critical threshold : 055 Major threshold : 050 Minor threshold : 045 Environment Monitor Data : Description : InltRear Shutdown threshold : 060 Critical threshold : 055 Major threshold : 050 Minor threshold : 045 Environment Monitor Data : Description : OtltFrnt Shutdown threshold : 090 Critical threshold : 085 Major threshold : 080 Minor threshold : 075 Environment Monitor Data : Description : OtltRear Shutdown threshold : 090 Critical threshold : 085 Major threshold : 080 Minor threshold : 075
lc-portmap 명령을 사용하여 수퍼바이저의 ASIC/코어에 대한 라인 카드 인터페이스 매핑에 대한 정보를 얻을 수 있습니다.
Cat9600#show platform hardware iomd 1/0 lc-portmap detail IOMD SUMMARY ============== spa_type: 0xd9a my_slot: 1 active-slot: 0 is_active: 1 bulk_sync_done: 1 bulk_sync_in_progress: 0 bulk_sync_received: 0 is_plugin_start_done: 1 Num_ports: 48 num_UDAP 3s: 3 PSM SUMMARY =============== PSM state: ready ha_state: is_spa_ok: 0 is_power_ok: 0 psm_flags: 0x0 bay_flags: 0x0 plugin_flags: 0x0 Port fp asic core mac cntx asic speed xcvr- xcvr- run- phy- i2c- xcvr- if- SerTune- False- Rcvr- Serdes- port pres type speed num ctrl sm state Status LinkUp idle set ================================================================================================================================ 0 1 0 0 0 0 0 40G no 0 unk 0 0 0 0 NOTS no 0 0 1 1 2 0 0 2 1 8 40G no 0 unk 0 0 0 0 NOTS no 0 2 3 2 3 0 0 16 0 16 40G no 0 unk 1 0 0 0 NOTS no 0 16 17 3 4 0 0 18 1 24 40G no 0 unk 1 0 0 0 NOTS no 0 18 19 4 5 0 1 14 1 8 40G no 0 unk 2 0 0 0 NOTS no 0 14 15 5 6 0 1 12 0 0 40G no 0 unk 2 0 0 0 NOTS no 0 12 13 6 7 0 1 30 1 24 40G no 0 unk 3 0 0 0 NOTS no 0 30 31 7 8 0 1 28 0 16 40G no 0 unk 3 0 0 0 NOTS no 0 28 29 8 9 1 0 0 0 0 40G no 0 unk 4 0 0 0 NOTS no 0 0 1 9 10 1 0 2 1 8 40G no 0 unk 4 0 0 0 NOTS no 0 2 3 10 11 1 0 16 0 16 40G no 0 unk 5 0 0 0 NOTS no 0 16 17 11 12 1 0 18 1 24 40G no 0 unk 5 0 0 0 NOTS no 0 18 19 12 13 1 1 14 1 8 40G no 0 unk 6 0 0 0 NOTS no 0 14 15 13 14 1 1 12 0 0 40G no 0 unk 6 0 0 0 NOTS no 0 12 13 14 15 1 1 30 1 24 40G no 0 unk 7 0 0 0 NOTS no 0 30 31 15 16 1 1 28 0 16 40G no 0 unk 7 0 0 0 NOTS no 0 28 29 16 17 2 0 0 0 0 40G no 0 unk 8 1 0 0 NOTS no 0 0 1 17 18 2 0 2 1 8 40G no 0 unk 8 1 0 0 NOTS no 0 2 3 18 19 2 0 16 0 16 40G no 0 unk 9 1 0 0 NOTS no 0 16 17 19 20 2 0 18 1 24 40G no 0 unk 9 1 0 0 NOTS no 0 18 19 20 21 2 1 14 1 8 40G no 0 unk 10 1 0 0 NOTS no 0 14 15 21 22 2 1 12 0 0 40G no 0 unk 10 1 0 0 NOTS no 0 12 13 22 23 2 1 30 1 24 40G no 0 unk 11 1 0 0 NOTS no 0 30 31 23 24 2 1 28 0 16 40G no 0 unk 11 1 0 0 NOTS no 0 28 29 24 25 0 0 0 0 0 100G no 0 unk 0 0 0 0 NOTS no 0 0 1 2 3 25 26 0 0 0 0 0 100G no 0 unk 0 0 0 0 NOTS no 0 0 1 2 3 26 27 0 0 16 0 16 100G no 0 unk 1 0 0 0 NOTS no 0 16 17 18 19 27 28 0 0 16 0 16 100G no 0 unk 1 0 0 0 NOTS no 0 16 17 18 19 28 29 0 1 12 0 0 100G no 0 unk 2 0 0 0 NOTS no 0 12 13 14 15 29 30 0 1 12 0 0 100G no 0 unk 2 0 0 0 NOTS no 0 12 13 14 15 30 31 0 1 28 0 16 100G no 0 unk 3 0 0 0 NOTS no 0 28 29 30 31 31 32 0 1 28 0 16 100G no 0 unk 3 0 0 0 NOTS no 0 28 29 30 31 32 33 1 0 0 0 0 100G no 0 unk 4 0 0 0 NOTS no 0 0 1 2 3 33 34 1 0 0 0 0 100G no 0 unk 4 0 0 0 NOTS no 0 0 1 2 3 34 35 1 0 16 0 16 100G no 0 unk 5 0 0 0 NOTS no 0 16 17 18 19 35 36 1 0 16 0 16 100G no 0 unk 5 0 0 0 NOTS no 0 16 17 18 19 36 37 1 1 12 0 0 100G no 0 unk 6 0 0 0 NOTS no 0 12 13 14 15 37 38 1 1 12 0 0 100G no 0 unk 6 0 0 0 NOTS no 0 12 13 14 15 38 39 1 1 28 0 16 100G no 0 unk 7 0 0 0 NOTS no 0 28 29 30 31 39 40 1 1 28 0 16 100G no 0 unk 7 0 0 0 NOTS no 0 28 29 30 31 40 41 2 0 0 0 0 100G no 0 unk 8 1 0 0 NOTS no 0 0 1 2 3 41 42 2 0 0 0 0 100G no 0 unk 8 1 0 0 NOTS no 0 0 1 2 3 42 43 2 0 16 0 16 100G no 0 unk 9 1 0 0 NOTS no 0 16 17 18 19 43 44 2 0 16 0 16 100G no 0 unk 9 1 0 0 NOTS no 0 16 17 18 19 44 45 2 1 12 0 0 100G no 0 unk 10 1 0 0 NOTS no 0 12 13 14 15 45 46 2 1 12 0 0 100G no 0 unk 10 1 0 0 NOTS no 0 12 13 14 15 46 47 2 1 28 0 16 100G no 0 unk 11 1 0 0 NOTS no 0 28 29 30 31 47 48 2 1 28 0 16 100G no 0 unk 11 1 0 0 NOTS no 0 28 29 30 31
Cat9600#show platform software fed [active | standby] ifm mappings Interface IF_ID Inst Asic Core Port SubPort Mac Cntx LPN GPN Type Active TwentyFiveGigE1/0/1 0x9 0 0 0 0 0 0 0 1 101 NIF Y TwentyFiveGigE1/0/2 0xa 0 0 0 4 0 1 1 2 102 NIF Y TwentyFiveGigE1/0/3 0xb 0 0 0 8 0 2 2 3 103 NIF Y TwentyFiveGigE1/0/4 0xc 0 0 0 12 0 3 3 4 104 NIF Y TwentyFiveGigE1/0/5 0xd 0 0 0 16 0 16 0 5 105 NIF Y TwentyFiveGigE1/0/6 0xe 0 0 0 20 0 17 1 6 106 NIF Y TwentyFiveGigE1/0/7 0xf 0 0 0 24 0 18 2 7 107 NIF Y TwentyFiveGigE1/0/8 0x10 0 0 0 28 0 19 3 8 108 NIF Y TwentyFiveGigE1/0/9 0x11 1 0 1 12 0 15 3 9 109 NIF Y TwentyFiveGigE1/0/10 0x12 1 0 1 8 0 14 2 10 110 NIF Y TwentyFiveGigE1/0/11 0x13 1 0 1 4 0 13 1 11 111 NIF Y TwentyFiveGigE1/0/12 0x14 1 0 1 0 0 12 0 12 112 NIF Y TwentyFiveGigE1/0/13 0x15 1 0 1 28 0 31 3 13 113 NIF Y TwentyFiveGigE1/0/14 0x16 1 0 1 24 0 30 2 14 114 NIF Y TwentyFiveGigE1/0/15 0x17 1 0 1 20 0 29 1 15 115 NIF Y TwentyFiveGigE1/0/16 0x18 1 0 1 16 0 28 0 16 116 NIF Y TwentyFiveGigE1/0/17 0x19 2 1 0 0 0 0 0 17 117 NIF Y TwentyFiveGigE1/0/18 0x1a 2 1 0 4 0 1 1 18 118 NIF Y TwentyFiveGigE1/0/19 0x1b 2 1 0 8 0 2 2 19 119 NIF Y TwentyFiveGigE1/0/20 0x1c 2 1 0 12 0 3 3 20 120 NIF Y TwentyFiveGigE1/0/21 0x1d 2 1 0 16 0 16 0 21 121 NIF Y TwentyFiveGigE1/0/22 0x1e 2 1 0 20 0 17 1 22 122 NIF Y TwentyFiveGigE1/0/23 0x1f 2 1 0 24 0 18 2 23 123 NIF Y TwentyFiveGigE1/0/24 0x20 2 1 0 28 0 19 3 24 124 NIF Y TwentyFiveGigE1/0/25 0x21 3 1 1 12 0 15 3 25 125 NIF Y TwentyFiveGigE1/0/26 0x22 3 1 1 8 0 14 2 26 126 NIF Y TwentyFiveGigE1/0/27 0x23 3 1 1 4 0 13 1 27 127 NIF Y TwentyFiveGigE1/0/28 0x24 3 1 1 0 0 12 0 28 128 NIF Y TwentyFiveGigE1/0/29 0x25 3 1 1 28 0 31 3 29 129 NIF Y TwentyFiveGigE1/0/30 0x26 3 1 1 24 0 30 2 30 130 NIF Y TwentyFiveGigE1/0/31 0x27 3 1 1 20 0 29 1 31 131 NIF Y TwentyFiveGigE1/0/32 0x28 3 1 1 16 0 28 0 32 132 NIF Y TwentyFiveGigE1/0/33 0x29 4 2 0 0 0 0 0 33 133 NIF Y TwentyFiveGigE1/0/34 0x2a 4 2 0 4 0 1 1 34 134 NIF Y TwentyFiveGigE1/0/35 0x2b 4 2 0 8 0 2 2 35 135 NIF Y TwentyFiveGigE1/0/36 0x2c 4 2 0 12 0 3 3 36 136 NIF Y TwentyFiveGigE1/0/37 0x2d 4 2 0 16 0 16 0 37 137 NIF Y TwentyFiveGigE1/0/38 0x2e 4 2 0 20 0 17 1 38 138 NIF Y TwentyFiveGigE1/0/39 0x2f 4 2 0 24 0 18 2 39 139 NIF Y TwentyFiveGigE1/0/40 0x30 4 2 0 28 0 19 3 40 140 NIF Y TwentyFiveGigE1/0/41 0x31 5 2 1 12 0 15 3 41 141 NIF Y TwentyFiveGigE1/0/42 0x32 5 2 1 8 0 14 2 42 142 NIF Y TwentyFiveGigE1/0/43 0x33 5 2 1 4 0 13 1 43 143 NIF Y TwentyFiveGigE1/0/44 0x34 5 2 1 0 0 12 0 44 144 NIF Y TwentyFiveGigE1/0/45 0x35 5 2 1 28 0 31 3 45 145 NIF Y TwentyFiveGigE1/0/46 0x36 5 2 1 24 0 30 2 46 146 NIF Y TwentyFiveGigE1/0/47 0x37 5 2 1 20 0 29 1 47 147 NIF Y TwentyFiveGigE1/0/48 0x38 5 2 1 16 0 28 0 48 148 NIF Y TwentyFiveGigE2/0/2 0x3a 0 0 0 9 0 9 9 2 202 NIF Y TwentyFiveGigE2/0/3 0x3b 0 0 0 10 0 10 10 3 203 NIF Y TwentyFiveGigE2/0/4 0x3c 0 0 0 11 0 11 11 4 204 NIF Y TwentyFiveGigE2/0/5 0x3d 0 0 0 18 0 24 8 5 205 NIF Y TwentyFiveGigE2/0/6 0x3e 0 0 0 25 0 25 9 6 206 NIF Y TwentyFiveGigE2/0/7 0x3f 0 0 0 26 0 26 10 7 207 NIF Y TwentyFiveGigE2/0/8 0x40 0 0 0 27 0 27 11 8 208 NIF Y TwentyFiveGigE2/0/9 0x41 1 0 1 7 0 7 7 9 209 NIF Y TwentyFiveGigE2/0/10 0x42 1 0 1 6 0 6 6 10 210 NIF Y TwentyFiveGigE2/0/11 0x43 1 0 1 5 0 5 5 11 211 NIF Y TwentyFiveGigE2/0/12 0x44 1 0 1 1 0 4 4 12 212 NIF Y TwentyFiveGigE2/0/13 0x45 1 0 1 23 0 23 7 13 213 NIF Y TwentyFiveGigE2/0/14 0x46 1 0 1 22 0 22 6 14 214 NIF Y TwentyFiveGigE2/0/15 0x47 1 0 1 21 0 21 5 15 215 NIF Y TwentyFiveGigE2/0/16 0x48 1 0 1 17 0 20 4 16 216 NIF Y TwentyFiveGigE2/0/17 0x49 2 1 0 2 0 8 8 17 217 NIF Y TwentyFiveGigE2/0/18 0x4a 2 1 0 9 0 9 9 18 218 NIF Y TwentyFiveGigE2/0/19 0x4b 2 1 0 10 0 10 10 19 219 NIF Y TwentyFiveGigE2/0/20 0x4c 2 1 0 11 0 11 11 20 220 NIF Y TwentyFiveGigE2/0/21 0x4d 2 1 0 18 0 24 8 21 221 NIF Y TwentyFiveGigE2/0/22 0x4e 2 1 0 25 0 25 9 22 222 NIF Y TwentyFiveGigE2/0/23 0x4f 2 1 0 26 0 26 10 23 223 NIF Y TwentyFiveGigE2/0/24 0x50 2 1 0 27 0 27 11 24 224 NIF Y TwentyFiveGigE2/0/25 0x51 3 1 1 7 0 7 7 25 225 NIF Y TwentyFiveGigE2/0/26 0x52 3 1 1 6 0 6 6 26 226 NIF Y TwentyFiveGigE2/0/27 0x53 3 1 1 5 0 5 5 27 227 NIF Y TwentyFiveGigE2/0/28 0x54 3 1 1 1 0 4 4 28 228 NIF Y TwentyFiveGigE2/0/29 0x55 3 1 1 23 0 23 7 29 229 NIF Y TwentyFiveGigE2/0/30 0x56 3 1 1 22 0 22 6 30 230 NIF Y TwentyFiveGigE2/0/31 0x57 3 1 1 21 0 21 5 31 231 NIF Y TwentyFiveGigE2/0/32 0x58 3 1 1 17 0 20 4 32 232 NIF Y TwentyFiveGigE2/0/33 0x59 4 2 0 2 0 8 8 33 233 NIF Y TwentyFiveGigE2/0/34 0x5a 4 2 0 9 0 9 9 34 234 NIF Y TwentyFiveGigE2/0/35 0x5b 4 2 0 10 0 10 10 35 235 NIF Y TwentyFiveGigE2/0/36 0x5c 4 2 0 11 0 11 11 36 236 NIF Y TwentyFiveGigE2/0/37 0x5d 4 2 0 18 0 24 8 37 237 NIF Y TwentyFiveGigE2/0/38 0x5e 4 2 0 25 0 25 9 38 238 NIF Y TwentyFiveGigE2/0/39 0x5f 4 2 0 26 0 26 10 39 239 NIF Y TwentyFiveGigE2/0/40 0x60 4 2 0 27 0 27 11 40 240 NIF Y TwentyFiveGigE2/0/41 0x61 5 2 1 7 0 7 7 41 241 NIF Y TwentyFiveGigE2/0/42 0x62 5 2 1 6 0 6 6 42 242 NIF Y TwentyFiveGigE2/0/43 0x63 5 2 1 5 0 5 5 43 243 NIF Y TwentyFiveGigE2/0/44 0x64 5 2 1 1 0 4 4 44 244 NIF Y TwentyFiveGigE2/0/45 0x65 5 2 1 23 0 23 7 45 245 NIF Y TwentyFiveGigE2/0/46 0x66 5 2 1 22 0 22 6 46 246 NIF Y TwentyFiveGigE2/0/47 0x67 5 2 1 21 0 21 5 47 247 NIF Y TwentyFiveGigE2/0/48 0x68 5 2 1 17 0 20 4 48 248 NIF Y
가장 일반적인 하드웨어 문제 및 검증 명령에 대해서는 이 가이드에서 적절한 교정 단계를 다룹니다. 그러나 이 설명서에서 문제를 해결하지 못한 경우 표시된 명령 목록을 수집하여 TAC 서비스 요청에 첨부하십시오.
show tech-support show post show platform hardware authentication status show platform hardware chassis fantray detail show platform software iomd redundancy
request platform software trace archive
service internal (for the standby command 'service internal' needs to be enabled first)
request platform software trace slot rp standby archive target stby-bootflash
개정 | 게시 날짜 | 의견 |
---|---|---|
1.0 |
05-Jul-2023 |
최초 릴리스 |