In dit document worden de minimale configuratiestappen beschreven die op de Huawei MA5600 Digital Subscriber Line Multiplexer (DSLAM) vereist zijn, zodat de Very-high-bit-Digital Subscriber Line (VDSL) in Cisco Customer Premise Equipment (CPE) kan trainen.
Cisco raadt u aan aan deze vereisten te vervullen voordat u deze configuratie probeert:
De informatie in dit document is gebaseerd op een Cisco 887VA-router die fungeert als een CPE en een Huwei 5600 DSLAM. Dit document is echter niet beperkt tot specifieke software- en hardwareversies.
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u de potentiële impact van elke opdracht begrijpen.
Dit document is bedoeld om engineers te helpen Cisco CPE en een Huawei DSLAM in een back-to-back-/labomgevingen op te zetten en de basisprofielen van het Central Office (CO)-einde van DSL te begrijpen.
Volg deze aanwijzingen op om uw apparatuur te configureren:
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 4
MA5600#config
MA5600(config)#vdsl line-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl line-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,G993.2)
> 2: Full rate(G992.1/3/5,T1.413,G993.2)
> 3: G.DMT (G992.1/3/5,G993.2)
> 4: G.HS (G992.1~5,G993.2)
> 5: ADSL (G.992.1~5,T1.413)
> 6: VDSL (G993.2)
> Please select (0~6) [1]:6 >>>>>>>>>>>>>>>>>> Selecting Transmission Mode as VDSL
> Bit swap downstream 1-disable 2-enable (1~2) [2]:1
> Bit swap upstream 1-disable 2-enable (1~2) [2]:1
> Please select the form of transmit rate adaptation downstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Please select the form of transmit rate adaptation upstream:
> 1-fixed 2-adaptAtStartup 3-AdaptAtRuntime (1~3) [2]:
> Will you set SNR margin parameters? (y/n) [n]:
> Will you set DPBO parameters? (y/n)[n]:
> Will you set UPBO parameters? (y/n)[n]:
> Will you set RFI notch configuration parameter? (y/n) [n]:
> Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
> Will you set mode-specific parameters? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 2
MA5600(config)#vdsl channel-profile add 60
Failure: The profile has existed
MA5600(config)#vdsl channel-profile add 61
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ZONE_TEST
> Data path mode 1-ATM, 2-PTM, 3-Both (1~3) [3]:2 >>>>>>>>>>>>>>>>>>>>>> PTM Mode
> Will you set the minimum impulse noise protection? (y/n) [n]:
> Will you set interleaving delay parameters? (y/n) [n]:
> Will you set parameters for rate? (y/n) [n]:
> Will you set rate thresholds? (y/n) [n]:
Add profile 61 successfully
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------>
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
------------------------------------------------------------------------------
Total: 5
MA5600(config)#vdsl line-template add 61
Start adding template
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the template (y/n) [n]:y
> Please input template name:ZONE_TEST
> Please set the line-profile index (1~128) [1]:61 >>>>>>>>>>>>>>>>Line Profile
we added above
> Will you set channel configuration parameters? (y/n) [n]:y
> Please set the channel number (1~2) [1]:
> Channel1 configuration parameters:
> Please set the channel-profile index (1~128) [1]:61 >>>>>> Channel Profile
we added above
Add template 61 successfully
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
In dit geval was de CPE verbonden met sleuf 5 poort 0 van de Huawei DSLAM.
MA5600(config)#display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1
-------------------------------------------------------------------------
0 H563ADGE Failed
1 H565ADBF Normal >>>>>>>>>ADBF - Here 'A' means that this card supports ADSL
2 ADG Failed
3 H569SHEB Failed
4
5 H565VDBD Normal >>>> >>>>VDBD - Here 'V' means that this card supports VDSL
6
7 H561SCU Standby_normal O2FM >>>>>>>>>>>>>>>>>>>>>> Processor Cards
8 H561SCU Active_normal O2GS O2GS >>>>>>>>>>>>> Processor Cards
9
10
11 H565VDBD Failed
12 H569SHEB Failed
13
14 H561SHEA Failed
15
-------------------------------------------------------------------------
MA5600(config)#interface vdsl 0/5 (Board/ slot)
Check the port status: Status is deactivated and currently assigned to
Line Template 1 (default)
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Deactivated Disable 1 1
-----------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#activate 0 template-index 61
>>>>>>>> We are already in board 0 slot 5, hence need to activate port 0 with
Line Template 61
MA5600(config-if-vdsl-0/5)#display port state 0
---------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activating Disable 61 1 >>>>>Check the status
---------------------------------------------------------------
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
---------------------------------------------------------------
0 Activated Disable 61 1 >>Status is activated
---------------------------------------------------------------
Deze sectie bevat informatie over het verifiëren van de configuratie.
De Output Interpreter Tool (alleen voor geregistreerde klanten) ondersteunt bepaalde opdrachten met show. Gebruik de Output Interpreter Tool om een analyse te bekijken van de output van de opdracht show.
MA5600#display vdsl line-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl line-profile
------------------------------------------------------------------------------
Profile Profile Transmission
Index Name Mode
------------------------------------------------------------------------------
60 Test_vdsl VDSL (G993.2)
61 ZONE_TEST VDSL (G993.2)
82 VDSL LINE PROFILE 82 VDSL (G993.2)
88 VDSL LINE PROFILE 88 VDSL (G993.2)
103 VDSL LINE PROFILE 103 VDSL (G993.2)
------------------------------------------------------------------------------
Total: 5
MA5600#display vdsl channel-profile
{ <cr>|profile-index<U><1,128> }:
Command:
display vdsl channel-profile
------------------------------------------------------------------------------
Profile Profile MinDw MaxDw MinUp MaxUp Data Path
Index Name Rate Rate Rate Rate Mode
------------------------------------------------------------------------------
60 test_vdsl 128 100000 128 100000 Both
61 ZONE_TEST 128 100000 128 100000 PTM
99 VDSL CHANNEL PRO 128 100000 128 100000 PTM
FILE 99
------------------------------------------------------------------------------
Total: 3
MA5600#display vdsl line-template
{ <cr>|template-index<U><1,128> }:
Command:
display vdsl line-template
------------------------------------------------------------------------------
Template Template Line Profile Channel1 Channnel2
Index Name Index Profile Index Profile Index
------------------------------------------------------------------------------
12 ios_test 10 11 -
16 DT-17a 18 18 -
17 profile_17a 17 17 -
18 aj_3M_US 17 5 -
60 VDSL LINE TEMPLA 60 60 -
TE 60
61 ZONE_TEST 61 61 -
------------------------------------------------------------------------------
Total: 6
Hiervoor dient u zich in de interface-configuratiemodus van de DSLAM te bevinden.
MA5600(config-if-vdsl-0/5)#display port state 0
-----------------------------------------------------------------
Port Status Loopback Line Template Alarm Template
-----------------------------------------------------------------
0 Activated Disable 61 1
-----------------------------------------------------------------
Voer de opdracht show controller vdsl 0 in op de CPE om de controlestatus te controleren.
/snip
C887VA-M#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0x939B
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FTX162580HZ 887VA-M 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0x939b
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 12a
TC Mode: PTM
Er is momenteel geen specifieke troubleshooting-informatie beschikbaar voor deze configuratie.
Revisie | Publicatiedatum | Opmerkingen |
---|---|---|
1.0 |
01-Dec-2014 |
Eerste vrijgave |