Verifique o multicast nativo na malha de acesso SD

Introdução

Este documento descreve como verificar o Multicast Nativo na estrutura SD-Access (SDA).

Pré-requisitos

Requisitos

A Cisco recomenda que você tenha conhecimento destes tópicos:

• Encaminhamento de Internet Protocol (IP)
• ID do localizador/protocolo de separação (LISP)
• Protocol Independent Multicast (PIM) Modo escasso

Componentes Utilizados

• C9000v no Cisco IOS® XE 17.10.1
• Cisco Catalyst Center versão 2.3.5.3

As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. Todos os dispositivos utilizados neste documento foram iniciados com uma configuração (padrão) inicial. Se a rede estiver ativa, certifique-se de que você entenda o impacto potencial de qualquer comando.

Este documento também pode ser usado com as seguintes versões de hardware e software:

• C9200
• C9300
• C9400
• C9500
• C9600
• Cisco IOS® XE 16.12 e posterior

Informações de Apoio

O SDA Native Multicast é uma forma de multicast de sobreposição, que é usado para transportar o tráfego multicast entre os dispositivos de estrutura, encapsulando o tráfego multicast em outro grupo multicast. O Multicast nativo pode rotear o tráfego multicast entre origens e receptores que estão na mesma VLAN ou em VLAN diferente (o multicast da mesma VLAN pode ser roteado). O tráfego multicast entre origens e recebimentos no mesmo Fabric Edge (FE) não é encaminhado usando multicast de sobreposição (encapsulamento VXLAN), mas é roteado localmente pelo FE. O multicast nativo não pode rotear o tráfego de multicast para grupos que correspondam a 224.0.0.0/24 ou a Time To Live (TTL) =1, eles são tratados por meio da inundação de Camada 2 (L2). O Multicast Nativo pode ser configurado para encaminhar Qualquer Multicast de Origem (ASM), Multicast Específico de Origem (SSM) ou uma combinação de ambos. O multicast nativo depende do multicast subjacente.

Topologia

Topologia de rede

Nesta topologia:

• Os IDs de localizador remoto (RLOC) 10.47.1.10 e 10.47.1.10 são colocados em qualquer lugar e também funcionam como Anycast Rendezvous Point (RP) com Multicast Source Discovery Protocol (MSDP) entre os dois na Virtual Network (VN) ou Virtual Routing and Forwarding (VRF).
• 10.47.1.12 e 10.47.1.3 são nós FE
• 10.47.7.4 é o receptor multicast
• 10.47.7.3 é a origem multicast
• 239.0.0.5 é o GDA (Group Destination Address, endereço de destino de grupo) multicast

Configuração

Supõe-se que o Cisco Catalyst Center seja usado para provisionar a estrutura SDA com estas configurações:

• A implementação do modo de replicação é multicast nativo
• O modo multicast é Any Source Multicast (ASM)
• Anycast Rendezvous Point (RP) com Multicast Source Discovery Protocol (MSDP) configurado no Collocated Anywhere Borders
• O Multicast de Sobreposição foi configurado manualmente ou como parte da Automação de LAN inicial, o Multicast Nativo depende do Multicast de Sobreposição para funcionar corretamente.

Configuração da borda da estrutura (10.47.1.12)

ip access-list standard ASM_ACL_IPV4_blue_vn_10.47.6.1
permit 239.0.0.0 0.0.0.255
ip multicast-routing vrf blue_vn
interface LISP0.4100
ip pim lisp transport multicast
ip pim lisp core-group-range 232.0.0.1 1000
interface Vlan1025
ip pim passive
exit
interface Loopback4100
vrf forwarding blue_vn
ip address 10.47.6.4 255.255.255.255
ip pim sparse-mode
ip pim vrf blue_vn rp-address 10.47.6.1 ASM_ACL_IPV4_blue_vn_10.47.6.1
ip pim vrf blue_vn register-source Loopback4100
ip pim vrf blue_vn ssm default
router lisp
service ipv4
etr map-server 10.47.1.11 key ******
etr map-server 10.47.1.10 key ******
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
service ethernet
etr map-server 10.47.1.11 key ******
etr map-server 10.47.1.10 key ******
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
instance-id-range 8188 , 8190 , 8192 , 8193 override
remote-rloc-probe on-route-change
service ethernet
eid-table vlan 1025 , 1026 , 1028 , 2727
database-mapping mac locator-set rloc_222e1707-175d-4019-a783-060404f8bc2f
instance-id 4099
service ipv4
sgt
instance-id 4100
service ipv4
sgt
database-mapping 10.47.6.4/32 locator-set rloc_222e1707-175d-4019-a783-060404f8bc2f
instance-id 8188
service ethernet
eid-table vlan 1025
dynamic-eid detection multiple-addr bridged-vm
instance-id 8190
service ethernet
eid-table vlan 1026
dynamic-eid detection multiple-addr bridged-vm
instance-id 8192
service ethernet
eid-table vlan 1028
dynamic-eid detection multiple-addr bridged-vm
ip domain lookup source-interface Loopback0
ip domain lookup
ip multicast vrf blue_vn multipath

Configuração da borda da estrutura (10.47.1.13)

ip access-list standard ASM_ACL_IPV4_blue_vn_10.47.6.1
permit 239.0.0.0 0.0.0.255
ip multicast-routing vrf blue_vn
interface LISP0.4100
ip pim lisp transport multicast
ip pim lisp core-group-range 232.0.0.1 1000
interface Vlan1025
ip pim passive
exit
interface Loopback4100
vrf forwarding blue_vn
ip address 10.47.6.3 255.255.255.255
ip pim sparse-mode
ip pim vrf blue_vn rp-address 10.47.6.1 ASM_ACL_IPV4_blue_vn_10.47.6.1
ip pim vrf blue_vn register-source Loopback4100
ip pim vrf blue_vn ssm default
router lisp
service ipv4
etr map-server 10.47.1.11 key ******
etr map-server 10.47.1.10 key ******
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
service ethernet
etr map-server 10.47.1.11 key ******
etr map-server 10.47.1.10 key ******
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
instance-id-range 8188 , 8190 , 8192 , 8193 override
remote-rloc-probe on-route-change
service ethernet
eid-table vlan 1025 , 1026 , 1028 , 2727
database-mapping mac locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51
instance-id 4099
service ipv4
sgt
instance-id 4100
service ipv4
sgt
database-mapping 10.47.6.3/32 locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51
instance-id 8188
service ethernet
eid-table vlan 1025
dynamic-eid detection multiple-addr bridged-vm
instance-id 8190
service ethernet
eid-table vlan 1026
dynamic-eid detection multiple-addr bridged-vm
instance-id 8192
service ethernet
eid-table vlan 1028
dynamic-eid detection multiple-addr bridged-vm
ip domain lookup source-interface Loopback0
ip domain lookup
ip multicast vrf blue_vn multipath

Configuração RP (10.47.1.10) de borda/anycast colocado em qualquer lugar

ip access-list standard ASM_ACL_IPV4_blue_vn_10.47.6.1
permit 239.0.0.0 0.0.0.255
ip multicast-routing vrf blue_vn
interface LISP0.4100
ip pim lisp transport multicast
ip pim lisp core-group-range 232.0.0.1 1000
interface Vlan3001
ip pim sparse-mode
exit
interface Loopback4100
vrf forwarding blue_vn
ip address 10.47.6.1 255.255.255.255
ip pim sparse-mode
interface Loopback4600
vrf forwarding blue_vn
ip address 10.47.6.6 255.255.255.255
ip pim sparse-mode
ip pim vrf blue_vn rp-address 10.47.6.1 ASM_ACL_IPV4_blue_vn_10.47.6.1
ip pim vrf blue_vn register-source Loopback4100
ip pim vrf blue_vn ssm default
ip msdp vrf blue_vn cache-sa-state
ip msdp vrf blue_vn originator-id Loopback4600
ip msdp vrf blue_vn peer 10.47.6.7 connect-source Loopback4600
ip msdp originator-id Loopback4600
router bgp 69420
address-family ipv4 vrf blue_vn
aggregate-address 10.47.6.0 255.255.255.0 summary-only
network 10.47.6.1 mask 255.255.255.255
router lisp
service ipv4
etr map-server 10.47.1.11 key ****** 
etr map-server 10.47.1.10 key ****** 
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
service ethernet
etr map-server 10.47.1.11 key ****** 
etr map-server 10.47.1.10 key ****** 
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
instance-id 4099
service ipv4
sgt
route-export site-registrations
route-import database bgp 69420 route-map DENY-red_vn locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
distance site-registrations 250
map-cache site-registration
instance-id 4100
service ipv4
map-cache 10.47.6.7/32 10.47.1.11 priority 1 weight 100
sgt
route-export site-registrations
route-import database bgp 69420 route-map DENY-blue_vn locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
distance site-registrations 250
map-cache site-registration
database-mapping 10.47.6.6/32 locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
database-mapping 10.47.6.1/32 locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
site site_uci
authentication-key ****** 
eid-record instance-id 4100 10.47.6.0/24 accept-more-specifics

Configuração RP (10.47.1.10) de borda/anycast colocado em qualquer lugar

ip access-list standard ASM_ACL_IPV4_blue_vn_10.47.6.1
permit 239.0.0.0 0.0.0.255
ip multicast-routing vrf blue_vn
interface LISP0.4100
ip pim lisp transport multicast
ip pim lisp core-group-range 232.0.0.1 1000
interface Vlan3001
ip pim sparse-mode
exit
interface Loopback4100
vrf forwarding blue_vn
ip address 10.47.6.1 255.255.255.255
ip pim sparse-mode
interface Loopback4600
vrf forwarding blue_vn
ip address 10.47.6.6 255.255.255.255
ip pim sparse-mode
ip pim vrf blue_vn rp-address 10.47.6.1 ASM_ACL_IPV4_blue_vn_10.47.6.1
ip pim vrf blue_vn register-source Loopback4100
ip pim vrf blue_vn ssm default
ip msdp vrf blue_vn cache-sa-state
ip msdp vrf blue_vn originator-id Loopback4600
ip msdp vrf blue_vn peer 10.47.6.7 connect-source Loopback4600
ip msdp originator-id Loopback4600
router bgp 69420
address-family ipv4 vrf blue_vn
aggregate-address 10.47.6.0 255.255.255.0 summary-only
network 10.47.6.1 mask 255.255.255.255
router lisp
service ipv4
etr map-server 10.47.1.11 key ******
etr map-server 10.47.1.10 key ******
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
service ethernet
etr map-server 10.47.1.11 key ******
etr map-server 10.47.1.10 key ******
etr map-server 10.47.1.10 proxy-reply
etr map-server 10.47.1.11 proxy-reply
instance-id 4099
service ipv4
sgt
route-export site-registrations
route-import database bgp 69420 route-map DENY-red_vn locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
distance site-registrations 250
map-cache site-registration
instance-id 4100
service ipv4
map-cache 10.47.6.7/32 10.47.1.11 priority 1 weight 100
sgt
route-export site-registrations
route-import database bgp 69420 route-map DENY-blue_vn locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
distance site-registrations 250
map-cache site-registration
database-mapping 10.47.6.6/32 locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
database-mapping 10.47.6.1/32 locator-set rloc_9080ed56-a6c6-482d-9f46-28eda0e18501
site site_uci
authentication-key ******
eid-record instance-id 4100 10.47.6.0/24 accept-more-specifics

Verificação do plano de controle

A verificação do Protocol Independent Multicast (PIM) ocorre nesta seção, começando com a validação da criação (S,G) no First Hop Router (FHR)

FHR (S,G) Criação 

A origem multicast, 10.47.7.3, envia pacotes multicast UDP para 239.0.0.5. Verifique se IP Device-Tracking (IPDT), Cisco Express Forwarding (CEF) e Reverse Path Forwarding (RPF) apontam corretamente para a origem de multicast. Além disso, certifique-se de que a SVI de gateway anycast seja o roteador designado (DR) PIM para esse segmento.

Use o comando "show device-tracking database address <ip address>" para garantir que haja uma entrada IPDT válida

Edge-2#show device-tracking database address 10.47.7.3
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
    Network Layer Address Link Layer Address Interface vlan prlvl age  state          Time left 
DH4 10.47.7.3             5254.0012.521d     Gi1/0/4   1025 0024  166s REACHABLE 81 s try 0(2276 s)

Use o comando "show ip cef vrf <VN Name> <ip address>" e verifique se a origem de multicast está diretamente conectada

Edge-2#show ip cef vrf blue_vn 10.47.7.3
10.47.7.3/32
nexthop 10.47.7.3 Vlan1025 

Em seguida, use o comando "show ip rpf vrf <VN> <ip address>" para garantir que a interface RPF seja a VLAN de origem, não LISP.

Edge-1#show ip rpf vrf blue_vn 10.47.7.3
RPF information for (10.47.7.2)
RPF interface: Vlan1025
RPF neighbor: ? (10.47.7.3) - directly connected
RPF route/mask: 10.47.7.3/32
RPF type: unicast (lisp)
Doing distance-preferred lookups across tables
Multicast Multipath enabled.
RPF topology: ipv4 multicast base, originated from ipv4 unicast base

Use o comando "show ip pim vrf <VN name> interface vlan <vlan> detail | incluir DR|enabled" para validar se o nó FE é o PIM DR para o segmento e é o FHR.

Edge-2#show ip pim vrf blue_vn interface vlan 1025 detail | include DR|enabled
PIM: enabled
PIM DR: 10.47.7.1 (this system)
PIM State-Refresh processing: enabled
PIM Non-DR-Join: FALSE

Use o comando "show ip mroute vrf <VN name> <multicast group address>" para validar a criação (S,G). (S,G) terá uma lista de interface de saída (OIL) nula porque não houve um receptor ou roteador PIM interessado que se juntou ao FHR. 

Edge-2#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 00:00:10/stopped, RP 10.47.6.1, flags: SPFl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10
Outgoing interface list: Null

(10.47.7.3, 239.0.0.5), 00:00:10/00:02:50, flags: PFT
Incoming interface: Vlan1025, RPF nbr 0.0.0.0
Outgoing interface list: Null

Registro FHR (S,G) 

O FHR registra a origem unicast para o RP Anycast, usando a interface configurada como Mensagens de Registro PIM de "origem registrada".

• Cabeçalho externo, RLOC para RLOC (10.47.1.13 a 10.47.1.10)
• Cabeçalho interno, Loopback para Loopback (10.47.6.3 a 10.47.6.1)
• Multicast real

Edge-2#show ip pim vrf blue_vn tunnel 
Tunnel1 
Type : PIM Encap
RP : 10.47.6.1
Source : 10.47.6.3
State : UP
Last event : Created (00:42:43)

Edge-2#show ip cef vrf blue_vn 10.47.6.1
10.47.6.1/32
nexthop 10.47.1.10 LISP0.4100 <-- FHR happened to register to this RP 
nexthop 10.47.1.11 LISP0.4100

Relatório de Associação LHR IGMP

O receptor multicast envia um Relatório/Junção de Associação IGMP para indicar o interesse no recebimento de tráfego multicast, que cria o Snooping IGMP e entradas de Grupo IGMP no Roteador de Último Salto (LHR). Use o comando "show ip igmp snooping groups vlan <vlan id> <group destination address>" bem como "show ip igmp vrf <VN Name> groups <group>"

Edge-1#show ip igmp snooping groups vlan 1025 239.0.0.5
Vlan Group     Type Version Port List
-----------------------------------------------------------------------
1025 239.0.0.5 igmp v2      Gi1/0/5

Edge-1#show ip igmp vrf blue_vn groups 239.0.0.5
IGMP Connected Group Membership
Group Address Interface Uptime   Expires  Last Reporter Group Accounted
239.0.0.5     Vlan1025  00:02:01 00:02:58 10.47.7.4 

Em seguida, certifique-se de que o LHR seja realmente o PIM DR para esse segmento, use o comando "show ip pim vrf <VN name> interface vlan <vlan> detail | incluir DR|habilitado" 

Edge-1#show ip pim vrf blue_vn interface vlan 1025 detail | include DR|enabled 
PIM: enabled
PIM DR: 10.47.7.1 (this system)
PIM State-Refresh processing: enabled
PIM Non-DR-Join: FALSE

Criação de sobreposição de LHR (*,G)

À medida que o LHR recebe o Relatório de Associação IGMP, ele também cria o estado PIM, especificamente (*,G) você pode usar o comando "show ip mroute vrf <VN Name><overlay group> verbose" para ver o estado (*,G)

Edge-1#show ip mroute vrf blue_vn 239.0.0.5 verbose 
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w3d/stopped, RP 10.47.6.1, flags: SJCl <-- Anycast RP IP address 
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10, LISP: [10.47.1.10, 232.0.2.245] <-- RPF neighbor to reach the Anycast RP, Overlay Group 239.0.0.5 is mapped to Underlay Group 232.0.2.245
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 1w3d/00:02:31, Pkts:0, flags: <-- IGMP Membership Report/PIM Join received in VLAN 1025, multicast traffic is sent into VLAN 1025

Mapeamento LHR (*,G) no Grupo Subjacente do SSM

Do (*,G), deriva-se a base SSM (S,G). A origem é RP RPF e Grupo é o mapeamento de sobreposição. 

Edge-1#show ip mroute 232.0.2.245 10.47.1.10
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.10, 232.0.2.245), 2d01h/00:02:28, flags: sT <-- 10.47.1.10 in this example is the RPF IP/neighbor to get to the RP, 232.0.2.245 is the Underlay Group 
Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.0 <-- RPF interface to reach 10.47.1.10
Outgoing interface list:
Null0, Forward/Dense, 2d01h/stopped, flags: <-- The Outgoing Interface List (OIL) is Null0, and in Native Multicast, this is treated as a De-Encapsulation interface

Borda/RP Cria (*,G) em Sobreposição e (S,G) em Sobreposição 

O LHR envia uma Junção PIM (*,G) na Sobreposição, você pode usar o comando "show ip mroute vrf <VN name> <overlay group> verbose" para exibir o (*,G) na Sobreposição 

Border-1#show ip mroute vrf blue_vn 239.0.0.5 verbose 
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 2d01h/00:03:05, RP 10.47.6.1, flags: Sp
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4100, (10.47.1.10, 232.0.2.245), Forward/Sparse, 2d01h/stopped, Pkts:0, flags: p
10.47.1.12, 2d01h/00:03:05 <-- This is the RLOC of Edge-1, which is the LHR 

No Underlay, você pode usar o comando "show ip mroute <underlay group address> <RP RLOC>"

Border-1#show ip mroute 232.0.2.245 10.47.1.10
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.10, 232.0.2.245), 2d01h/00:03:13, flags: sT
Incoming interface: Null0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet1/0/3, Forward/Sparse, 2d01h/00:03:13, flags: <-- Interface that connects to Edge-1, which is the LHR, a PIM Join was received off this interface 

Border-1 cria (S,G) a partir do MSDP SA-Cache 

O FHR registrou a origem de multicast para Border-2. Border-2 anuncia a origem de multicast para Border-1 via MSDP. Você pode usar o comando "show ip msdp vrf <VN Name> summary" para exibir o status MSDP. 

Border-1#show ip msdp vrf blue_vn summary 
MSDP Peer Status Summary
Peer Address AS    State Uptime/  Reset SA   Peer Name
                         Downtime Count Count
10.47.6.7    23456 Up    2d02h    1     1 

Use o comando "show ip msdp vrf <VN Name> peer <Peer Address> accept-SAs" para ver as SAs aceitas do peer

Border-1#show ip msdp vrf blue_vn peer 10.47.6.7 accepted-SAs
MSDP SA accepted from peer 10.47.6.7 (?)
239.0.0.5 10.47.7.3 (?) RP: 10.47.6.7 <-- 239.0.0.5 is the Overlay Group, 10.47.7.3 is the multicast source, 10.47.6.7 is the IP address on Border-2 in the VRF

Use o comando "show ip mroute vrf <VN Name> <group destination address> verbose" para ver (S,G)

Border-1#show ip mroute vrf blue_vn 239.0.0.5 verbose 
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 2d02h/00:03:27, RP 10.47.6.1, flags: Sp
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4100, (10.47.1.10, 232.0.2.245), Forward/Sparse, 2d02h/stopped, Pkts:0, flags: p
10.47.1.12, 2d02h/00:03:27

(10.47.7.3, 239.0.0.5), 00:18:26/00:02:50, flags: PTA <-- True multicast source 
Incoming interface: LISP0.4100, RPF nbr 10.47.1.13, LISP: [10.47.1.13, 232.0.2.245] <-- RLOC of Edge-2, which is FHR, and 232.0.2.245 is the Underlay multicast group 
Outgoing interface list:
10.47.1.12, 00:00:05/00:03:24 <-- RLOC of Edge-1

Sobreposição de Borda (S,G) cria Sobreposição (S,G)

Border-1 cria a Sobreposição (S,G) como resultado da Sobreposição (S,G), você pode usar o comando "show ip mroute <group destination address>" para ver informações adicionais.

Há dois (S,G)s, para o FHR e para ele mesmo. O Null0 OIL para 10.47.1.13, 232.0.2.245 indica desencapsulamento, o Null0 como um IIF para 10.47.1.10 indica encapsulamento. 

Border-1#show ip mroute 232.0.2.245
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.13, 232.0.2.245), 00:02:34/00:00:25, flags: sPT <-- RLOC of the FHR, underlay multicast group IP
Incoming interface: GigabitEthernet1/0/4, RPF nbr 10.47.1.3 <-- RPF interface towards the FHR
Outgoing interface list: Null <-- Indicates decapsulation 

(10.47.1.10, 232.0.2.245), 2d02h/00:02:41, flags: sT <-- RLOC of Border-1, underlay multicast group IP
Incoming interface: Null0, RPF nbr 0.0.0.0 <-- Indicates encapsulation 
Outgoing interface list:
GigabitEthernet1/0/3, Forward/Sparse, 2d02h/00:02:41, flags: <-- where multicast traffic is sent 

FHR Recebe (S,G) Junção em Sobreposição e Sobreposição

O Border/RP envia PIM (S,G) Joins em direção ao FHR, você pode usar o comando "show ip mroute" para obter informações. Na Sobreposição, use "show ip mroute vrf <VN Name> <overlay group address"

Edge-2#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w3d/stopped, RP 10.47.6.1, flags: SPFl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10
Outgoing interface list: Null

(10.47.7.3, 239.0.0.5), 1w3d/00:01:23, flags: FT <-- Multicast source, true multicast group 
Incoming interface: Vlan1025, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4100, (10.47.1.13, 232.0.2.245), Forward/Sparse, 19:12:56/stopped, flags: <-- FHR RLOC, underlay group IP 
10.47.1.10, 00:00:09/00:03:19 <-- Border/RP  RLOC 

Na subjacência, use "show ip mroute <underlay group address>"

Edge-2#show ip mroute 232.0.2.245
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.13, 232.0.2.245), 1w3d/00:03:01, flags: sT <-- RLOC of the FHR, Underlay multicast group 
Incoming interface: Null0, RPF nbr 0.0.0.0 <-- Indicates encapsulation 
Outgoing interface list:
GigabitEthernet1/0/1, Forward/Sparse, 00:01:42/00:03:01, flags: <-- Where the multicast traffic is forwarded 

O LHR recebe o tráfego multicast ao longo da árvore compartilhada

Depois que o LHR recebe o tráfego de multicast encapsulado ao longo da árvore compartilhada do RP, ele desencapsula o tráfego de multicast como o OIL na subjacência (S,G) é Null0 e, em seguida, cria uma entrada (S,G) na sobreposição. Você pode usar os comandos "show ip mroute <underlay group address>" e "show ip mroute vrf <VN Name> <overlay group address" 

Edge-1#show ip mroute 232.0.2.245 
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.10, 232.0.2.245), 2d03h/00:00:36, flags: sT <-- RLOC of the RP, Underlay group 
Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.0 <-- RPF interface towards the RP 
Outgoing interface list:
Null0, Forward/Dense, 2d03h/stopped, flags: <-- Indicates Decapsulation 

No campo Sobrepor "show ip mroute vrf <VN Name> <overlay group address>" 

Edge-1#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w3d/stopped, RP 10.47.6.1, flags: SJCl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 1w3d/00:02:03, flags:

(10.47.7.3, 239.0.0.5), 00:01:21/00:01:38, flags: JTl <-- Multicast Source, Overlay Group 
Incoming interface: LISP0.4100, RPF nbr 10.47.1.13, LISP:
 [10.47.1.13, 232.0.2.245] <-- RLOC of the FHR, Underlay Group 
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 00:01:21/00:02:03, flags: <-- Multicast traffic is fowarded into VLAN 1025 

Agora, o LHR se junta à SPT (Shortest Path Tree, Árvore de caminho mais curto) e remove a árvore compartilhada, por meio de PIM (S,G) Joins na Sobreposição e na Sobreposição. Depois que o LHR remove a Árvore compartilhada, o RP OIL para (S,G) não inclui mais o LHR. Vá para o RP e use o comando "show ip mroute vrf <VN Name> <overlay group address>"

Border-1#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 2d04h/00:03:10, RP 10.47.6.1, flags: S
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4100, (10.47.1.10, 232.0.2.245), Forward/Sparse, 2d04h/stopped, flags:

(10.47.7.3, 239.0.0.5), 00:14:17/00:02:42, flags: PT
Incoming interface: LISP0.4100, RPF nbr 10.47.1.13
Outgoing interface list: Null

Como a estrutura (S,G) não tem mais um mapeamento de subjacência, mesmo que o tráfego para 239.0.0.5 seja recebido através da subjacência, o RP não o reencapsula para qualquer LHR, que remove a árvore compartilhada. No entanto, a estrutura (S,G) para a Árvore de origem e a Árvore compartilhada ainda existe. Vá até o RP e verifique o grupo Underlay com o comando "show ip mroute <underlay group address>"

Border-1#show ip mroute 232.0.2.245
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.13, 232.0.2.245), 00:01:07/00:01:52, flags: sPT
Incoming interface: GigabitEthernet1/0/4, RPF nbr 10.47.1.3
Outgoing interface list: Null

(10.47.1.10, 232.0.2.245), 2d04h/00:03:23, flags: sT
Incoming interface: Null0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet1/0/3, Forward/Sparse, 2d04h/00:03:23, flags:

Se o RP tiver removido todo o(s) seu(s) ÓLEO(s), ele também será removido do ÓLEO FHR, e o ÓLEO FHR incluirá somente LHR(s). Vá para o FHR e use o comando "show ip mroute vrf <VN Name> <overlay group address>"

Edge-2#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w4d/stopped, RP 10.47.6.1, flags: SPFl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10
Outgoing interface list: Null

(10.47.7.3, 239.0.0.5), 1w3d/00:01:25, flags: FT <-- Multicast Source, Overlay Group 
Incoming interface: Vlan1025, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4100, (10.47.1.13, 232.0.2.245), Forward/Sparse, 20:16:48/stopped, flags: <-- RLOC of the LHR, Underlay Group 

Verificação do plano de dados (independente de plataforma)

Pode haver vários problemas que podem impedir a origem de multicast ou o receptor de multicast de enviar/receber o tráfego. Esta seção se concentra na validação de problemas que podem afetar a origem e o receptor multicast, com ênfase em problemas que não estão relacionados à programação de hardware.

Criação de FHR (S,G)

Para que o FHR crie (S,G) e verifique se SISF, LISP, CEF e RPF são válidos e corretos, use o comando "show device-tracking database address <IPv4 address>"

Edge-2#show device-tracking database address 10.47.7.3
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
    Network Layer Address Link Layer Address Interface vlan prlvl age state     Time left 
DH4 10.47.7.3             5254.0012.521d     Gi1/0/4   1025 0024  16s REACHABLE 232 s try 0(84662 s)

 O SISF é utilizado pelo LISP, use o comando "show lisp instance-id <L3 LISP Instance ID> ipv4 database <IP/32>"

Edge-2#show lisp instance-id 4100 ipv4 database 10.47.7.3/32
LISP ETR IPv4 Mapping Database for LISP 0 EID-table vrf blue_vn (IID 4100), LSBs: 0x1
Entries total 1, no-route 0, inactive 0, do-not-register 1
10.47.7.3/32, dynamic-eid blue-IPV4, inherited from default locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51
Uptime: 5w0d, Last-change: 5w0d
Domain-ID: local
Service-Insertion: N/A
Locator Pri/Wgt Source State
10.47.1.13 10/10 cfg-intf site-self, reachable
Map-server Uptime ACK Domain-ID 
10.47.1.10 2d04h Yes 0 
10.47.1.11 2d15h Yes 0

Edge-2#show ip lisp instance-id 4100 forwarding eid local 10.47.7.3 
Prefix
10.47.7.3/32

 Programas LISP CEF, use o comando "show ip cef vrf <VN Name> <ip address>" e certifique-se de que seja o próximo salto na VLAN, sem apontar para LISP.

Edge-2#show ip cef vrf blue_vn 10.47.7.3
10.47.7.3/32
nexthop 10.47.7.3 Vlan1025

Por fim, verifique se o RPF está apontando corretamente e diz que está conectado diretamente.

Edge-2#show ip rpf vrf blue_vn 10.47.7.3
RPF information for (10.47.7.3)
RPF interface: Vlan1025
RPF neighbor: ? (10.47.7.3) - directly connected
RPF route/mask: 10.47.7.3/32
RPF type: unicast (lisp)
Doing distance-preferred lookups across tables
Multicast Multipath enabled.
RPF topology: ipv4 multicast base, originated from ipv4 unicast base

 Se não houver uma entrada válida no SISF/IPDT, isso resultará em nenhum mapeamento de banco de dados LISP no FHR, o que resulta em CEF e RPF apontando para a(s) borda(s). Se a origem multicast envia tráfego, o RPF aponta para a interface incorreta, o que resulta em falha do RPF, (S,G) não é formado.

Edge-2#show device-tracking database address 10.47.7.3
Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created
Preflevel flags (prlvl):
0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 
0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 
0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned
Network Layer Address Link Layer Address Interface vlan prlvl age state Time left

Edge-2#show lisp instance-id 4100 ipv4 database 10.47.7.3/32
% No database-mapping entry for 10.47.7.3/32.

Edge-2#show ip cef vrf blue_vn 10.47.7.3
10.47.7.0/24
nexthop 10.47.1.10 LISP0.4100 <-- Result of a LISP Negative Map-Reply, so the LISP interface is now the RPF interface 
nexthop 10.47.1.11 LISP0.4100 <-- Result of a LISP Negative Map-Reply, so the LISP interface is now the RPF interface 

Edge-2#show ip rpf vrf blue_vn 10.47.7.3
RPF information for (10.47.7.3)
RPF interface: LISP0.4100
RPF neighbor: ? (10.47.1.11)
RPF route/mask: 10.47.7.3/32
RPF type: unicast ()
Doing distance-preferred lookups across tables
Multicast Multipath enabled.
RPF topology: ipv4 multicast base   

 Para evitar isso, trate a origem de multicast como um host silencioso, onde as vinculações de transmissão direcionada por IP, inundação, SISF estático/IPDT podem superar esse problema. 

Registro de Origem

O registro PIM é um fluxo de pacote unicast, que usa LISP/VXLAN como qualquer outro pacote unicast. Existem vários requisitos para validar se o FHR pode registrar corretamente a origem de multicast para o RP Anycast.

Primeiro, verifique se o RP Anycast está configurado corretamente para o GDA.

Edge-2#show ip pim vrf blue_vn rp 239.0.0.5
Group: 239.0.0.5, RP: 10.47.6.1, uptime 1w4d, expires never

Verifique se o túnel PIM Register está formado.

Edge-2#show ip pim vrf blue_vn tunnel 
Tunnel1 
Type : PIM Encap
RP : 10.47.6.1 <-- This is from "ip pim vrf blue_vn rp-address 10.47.6.1 ASM_ACL_IPV4_blue_vn_10.47.6.1"
Source : 10.47.6.3 <-- This is from ip pim vrf blue_vn register-source Loopback4100
State : UP
Last event : Created (1w4d)

 Verifique se há acessibilidade de IP para o RP Anycast

Edge-2#show ip cef vrf blue_vn 10.47.6.1
10.47.6.1/32
nexthop 10.47.1.10 LISP0.4100 <-- RLOC of Border-1
nexthop 10.47.1.11 LISP0.4100 <-- RLOC of Border-2

Edge-2#ping vrf blue_vn 10.47.6.1 source lo4100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.47.6.1, timeout is 2 seconds:
Packet sent with a source address of 10.47.6.3 
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/3 ms 

Verificação no lado do receptor

• Verifique se o receptor multicast está enviando um IGMP MR.
• Certifique-se de que o Snooping IGMP esteja habilitado. As VLANs somente L2 são o único tipo de VLAN que não tem o Snooping IGMP habilitado
• Verifique se não há uma ACL de porta, ACL de VLAN, ACL de porta roteada configurada que descartaria o IGMP MR.
• Validar a versão do IGMP MR; por padrão, é IGMPv2, se o receptor multicast for IGMPv3, isso exigirá "ip igmp version 3"
• Certifique-se de que a opção "ip option drop" não esteja configurada

Verificação LHR PIM (*,G)

• Certifique-se de que o LHR seja o DR PIM para a sub-rede/segmento do receptor
• Certifique-se de que não haja nenhum "ip multicast group-range" configurado  
• Verifique se não há uma ACL de porta, ACL de VLAN, ACL de porta roteada configurada que descartaria o IGMP MR.
• Certifique-se de que não haja CPU alta ou Política de Plano de Controle (CoPP) descartando o IGMP MR.

Verificação de Árvore Compartilhada PIM LHR

Verifique se há um RP configurado para o grupo

Edge-1#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w3d/stopped, RP 10.47.6.1, flags: SJCl <-- Anycast RP address 
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 1w3d/00:02:36, flags:

Verifique se o RPF para o RP Anycast está correto

Edge-1#show ip cef vrf blue_vn 10.47.6.1
10.47.6.1/32
nexthop 10.47.1.10 LISP0.4100
nexthop 10.47.1.11 LISP0.4100

Edge-1#show ip rpf vrf blue_vn 10.47.6.1
RPF information for (10.47.6.1)
RPF interface: LISP0.4100
RPF neighbor: ? (10.47.1.10)
RPF route/mask: 10.47.6.1/32
RPF type: unicast ()
Doing distance-preferred lookups across tables
Multicast Multipath enabled.
RPF topology: ipv4 multicast base

 Encaminhamento de MFIB - Verificação da origem de multicast nativo (sobreposição)

Você pode usar o comando "show ip mfib vrf <VN Name> <overlay group address> <unicast source> verbose" para obter informações adicionais sobre o encaminhamento de pacotes.

Edge-2#show ip mfib vrf blue_vn 239.0.0.5 10.47.7.3 verbose 
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB 
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client,
e - Encap helper tunnel flag.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
VRF blue_vn
(10.47.7.3,239.0.0.5) Flags: K HW DDE
0x530 OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 352467143981268992/0/19/0, Other: 0/0/0
Vlan1025 Flags: RA A MA
LISP0.4100, (10.47.1.13, 232.0.2.245) Flags: RF F NS <-- RLOC of FHR, Underlay Group IP address 
CEF: Adjacency with MAC: 4500000000004000001184BC0A2F010DE80002F5000012B5000000000840000000100400BA25CDF4AD38BA25CDF4AD380000
Pkts: 0/0/0 Rate: 0 pps

Encaminhamento de MFIB - Verificação do lado da origem de multicast nativo (subjacência)

Use "show ip mroute <underlay group address> <RLOC of FHR>" para exibir o grupo Underlay 

Edge-2#show ip mroute 232.0.2.245 10.47.1.13
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.13, 232.0.2.245), 1w4d/00:03:17, flags: sT <-- RLOC of the FHR, Underlay Group 
Incoming interface: Null0, RPF nbr 0.0.0.0 <-- Indicates Encapsulation 
Outgoing interface list:
GigabitEthernet1/0/1, Forward/Sparse, 00:00:26/00:03:17, flags <-- Where the multicast traffic is forwarded

Edge-2#show ip mfib 232.0.2.245 10.47.1.13 verbose 
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB 
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client,
e - Encap helper tunnel flag.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
Default
(10.47.1.13,232.0.2.245) Flags: K HW
0x348 OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 5268151634814304256/0/1/0, Other: 0/0/0
Null0 Flags: RA A MA
GigabitEthernet1/0/1 Flags: RF F NS
CEF: Adjacency with MAC: 01005E0002F552540017FE730800
Pkts: 0/0/0 Rate: 0 pps

Encaminhamento MFIB - Multicast nativo (pós-desencapsulamento)

Quando o tráfego multicast chega ao LHR encapsulado com um IP de origem de 10.47.1.13 e um endereço de destino de 232.0.2.245, ele é roteado para a interface de saída Null0. Esta ação dispara o desencapsulamento do pacote. 

Edge-1#show ip mroute 232.0.2.245 10.47.1.13
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.47.1.13, 232.0.2.245), 00:38:22/00:00:37, flags: sT
Incoming interface: GigabitEthernet1/0/2, RPF nbr 10.47.1.4
Outgoing interface list:
Null0, Forward/Dense, 00:01:12/stopped, flags: 

Edge-1#show ip mfib 232.0.2.245 10.47.1.13 verbose 
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB 
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client,
e - Encap helper tunnel flag.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
Default
(10.47.1.13,232.0.2.245) Flags: K HW
0x77 OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 0/0/0/0, Other: 0/0/0
GigabitEthernet1/0/2 Flags: RA A MA
Null0, LISPv4 Decap Flags: RF F NS
CEF: OCE (lisp decap)
Pkts: 0/0/0 Rate: 0 pps

Após o desencapsulamento, o LHR identifica que o endereço IP destino verdadeiro é 239.0.0.5 no VNI 4100, originado com um IP origem de 10.47.7.3

Edge-1#show ip mroute vrf blue_vn 239.0.0.5
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w3d/stopped, RP 10.47.6.1, flags: SJCl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 1w3d/00:02:01, flags:

(10.47.7.3, 239.0.0.5), 00:01:29/00:01:30, flags: JTl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.13
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 00:01:29/00:02:01, flags:

Edge-1#show ip mfib vrf blue_vn 239.0.0.5 10.47.7.3
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB 
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client,
e - Encap helper tunnel flag.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
VRF blue_vn
(10.47.7.3,239.0.0.5) Flags: HW <-- Unicast Source and Overlay Group 
SW Forwarding: 0/0/0/0, Other: 2/1/1
HW Forwarding: 0/0/0/0, Other: 0/0/0
LISP0.4100 Flags: A <-- Incoming Interface 
Vlan1025 Flags: F NS <-- Outgoing Interface
Pkts: 0/0/0 Rate: 0 pps

Use o comando "show ip igmp snooping groups vlan <VLAN>" para ver quais portas receberão tráfego multicast.

Edge-1#show ip igmp snooping groups vlan 1025
Vlan Group     Type Version Port List
-----------------------------------------------------------------------
1025 239.0.0.5 igmp v2      Gi1/0/5

Verificação do plano de dados (dependente da plataforma)

Programação de hardware Mroute - IOS mroute

A programação de hardware usa esta cadeia: IOS, depois FMAN RP, para FMAN FP e, em seguida, FED. Verifique o IOS primeiro, com os comandos "show ip mroute vrf <Nome VN> <endereço de grupo de sobreposição> verbose" e "show ip mroute <endereço de grupo de subcamada> verbose"

Edge-1#show ip mroute vrf blue_vn 239.0.0.5 verbose 
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 239.0.0.5), 1w3d/stopped, RP 10.47.6.1, flags: SJCl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.10, LISP: [10.47.1.10, 232.0.2.245]
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 1w3d/00:02:58, Pkts:0, flags:

(10.47.7.3, 239.0.0.5), 00:02:19/00:00:40, flags: JTl
Incoming interface: LISP0.4100, RPF nbr 10.47.1.13, LISP: [10.47.1.13, 232.0.2.245]
Outgoing interface list:
Vlan1025, Forward/Sparse-Dense, 00:02:19/00:02:58, Pkts:0, flags:

Na subjacência

Edge-1#show ip mroute 232.0.2.245 verbose 
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, 
Z - Multicast Tunnel, z - MDT-data group sender, 
Y - Joined MDT-data group, y - Sending to MDT-data group, 
G - Received BGP C-Mroute, g - Sent BGP C-Mroute, 
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, 
Q - Received BGP S-A Route, q - Sent BGP S-A Route, 
V - RD & Vector, v - Vector, p - PIM Joins on route, 
x - VxLAN group, c - PFP-SA cache created entry, 
* - determined by Assert, # - iif-starg configured on rpf intf, 
e - encap-helper tunnel flag, l - LISP decap ref count contributor
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
t - LISP transit group
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode

(10.47.1.13, 232.0.2.245), 01:18:55/00:02:04, flags: sT
Incoming interface: GigabitEthernet1/0/2, RPF nbr 10.47.1.4
LISP EID ref count: 1, Underlay ref timer: 00:05:13
Outgoing interface list:
Null0, Forward/Dense, 00:01:46/stopped, Pkts:0, flags:
(10.47.1.10, 232.0.2.245), 2d06h/00:02:59, flags: sT
Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.0
LISP EID ref count: 1, Underlay ref timer: 00:05:12
Outgoing interface list:
Null0, Forward/Dense, 2d06h/stopped, Pkts:0, flags: 

Programação de hardware Mroute - IOS MFIB

Verifique o Overlay e o Underlay MFIB com os comandos "show ip mfib vrf <VN Name> <overlay group address> verbose" e "show ip mroute <underlay group address> verbose"

Na página Sobreposição,

Edge-1#show ip mfib vrf blue_vn 239.0.0.5 verbose 
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB 
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client,
e - Encap helper tunnel flag.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
VRF blue_vn
(*,239.0.0.5) Flags: C K HW
0x6D OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 16218869633044709376/0/0/0, Other: 0/0/0
LISP0.4100 Flags: RA A MA NS
Vlan1025 Flags: RF F NS
CEF: Adjacency with MAC: 01005E00000500000C9FFB870800
Pkts: 0/0/0 Rate: 0 pps
(10.47.7.3,239.0.0.5) Flags: K HW DDE
0x7B OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 2/0/2
HW Forwarding: 0/0/0/0, Other: 0/0/0
LISP0.4100 Flags: RA A MA
Vlan1025 Flags: RF F NS
CEF: Adjacency with MAC: 01005E00000500000C9FFB870800
Pkts: 0/0/0 Rate: 0 pps

Na subjacência

Edge-1#show ip mfib 232.0.2.245 verbose
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB 
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client,
e - Encap helper tunnel flag.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: HW Pkt Count/FS Pkt Count/PS Pkt Count Egress Rate in pps
Default
(10.47.1.10,232.0.2.245) Flags: K HW
0x18 OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 8384858081233731584/0/0/0, Other: 0/0/0
GigabitEthernet1/0/1 Flags: RA A MA
Null0, LISPv4 Decap Flags: RF F NS
CEF: OCE (lisp decap)
Pkts: 0/0/0 Rate: 0 pps
(10.47.1.13,232.0.2.245) Flags: K HW
0x77 OIF-IC count: 0, OIF-A count: 1
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 0/0/0/0, Other: 0/0/0
GigabitEthernet1/0/2 Flags: RA A MA
Null0, LISPv4 Decap Flags: RF F NS
CEF: OCE (lisp decap)
Pkts: 0/0/0 Rate: 0 pps

Programação de hardware Mroute - FMAN RP

Para validar FMAN RP, primeiro capture o ID do VRF.

Edge-1#show vrf detail blue_vn | include Id
VRF blue_vn (VRF Id = 2); default RD <not set>; default VPNID <not set>

Em seguida, use o valor de índice VRF para os próximos comandos. Para validar a Sobreposição (*,G), use o comando "show platform software ip switch ative r0 mfib vrf index <VRF Index> group <overlay group address>/32"

Edge-1#show platform software ip switch active r0 mfib vrf index 2 group 239.0.0.5/32 
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
*, 239.0.0.5/32 --> OBJ_INTF_LIST (0x6d)
Obj id: 0x6d, Flags: C
OM handle: 0x348030b738 

 Para validar a Sobreposição (S,G), use o comando "show platform software ip switch ative r0 mfib vrf index 2 group address <overlay group address> <unicast source>"

Edge-1#show platform software ip switch active r0 mfib vrf index 2 group address 239.0.0.5 10.47.7.3
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
239.0.0.5, 10.47.7.3/64 --> OBJ_INTF_LIST (0x7f)
Obj id: 0x7f, Flags: unknown
OM handle: 0x34803a3800 

  Para validar a Sobreposição (S,G), use o comando "show platform software ip switch ative r0 mfib group address <underlay group address> <RP address>"

Edge-1#show platform software ip switch active r0 mfib group address 232.0.2.245 10.47.1.10
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
232.0.2.245, 10.47.1.10/64 --> OBJ_INTF_LIST (0x18)
Obj id: 0x18, Flags: unknown
OM handle: 0x34803b9be8

Para validar a Sobreposição (S,G), use o comando "show platform software ip switch ative r0 mfib group address <underlay group address> <RLOC of FHR>"

Edge-1#show platform software ip switch active r0 mfib group address 232.0.2.245 10.47.1.13
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
232.0.2.245, 10.47.1.13/64 --> OBJ_INTF_LIST (0x77)
Obj id: 0x77, Flags: unknown
OM handle: 0x348026b988

Programação de hardware Mroute - FMAN FP

Para validar a Sobreposição (*,G), use o comando "show platform software ip switch ative f0 mfib vrf index <VRF ID> group <overlay group address>"

Edge-1#show platform software software ip switch active f0 mfib vrf index 2 group 239.0.0.5/32 
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
*, 239.0.0.5/32 --> OBJ_INTF_LIST (0x6d)
Obj id: 0x6d, Flags: C
aom id: 100880, HW handle: (nil) (created)

Para validar a Sobreposição (S,G), use o comando "show platform software ip switch ative f0 mfib vrf index <VRF ID> group address <overlay group address> <unicast source>"

Edge-1#show platform software ip switch active f0 mfib vrf index 2 group address 239.0.0.5 10.47.7.3 
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
239.0.0.5, 10.47.7.3/64 --> OBJ_INTF_LIST (0x8f)
Obj id: 0x8f, Flags: unknown
aom id: 161855, HW handle: (nil) (created)

Para validar a subjacência (S,G) para a sobreposição (*,G), use o comando ""show platform software ip switch ative f0 mfib group address <underlay group address> <RP address>"

Edge-1#show platform ip switch active f0 mfib group address 232.0.2.245 10.47.1.10
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
232.0.2.245, 10.47.1.10/64 --> OBJ_INTF_LIST (0x18)
Obj id: 0x18, Flags: unknown
aom id: 138716, HW handle: (nil) (created)

Para validar a Sobreposição (S,G), use o comando "show platform software ip switch ative f0 mfib group address <underlay group address> <RLOC of FHR>"

Edge-1#show platform software ip switch active f0 mfib group address 232.0.2.245 10.47.1.13 
Route flags:
S - Signal; C - Directly connected;
IA - Inherit A Flag; L - Local;
BR - Bidir route
232.0.2.245, 10.47.1.13/64 --> OBJ_INTF_LIST (0x5)
Obj id: 0x5, Flags: unknown
aom id: 161559, HW handle: (nil) (created)

Programação de hardware Mroute - FMAN FP Database

Para validar o objeto FMAN FP, use o comando "show platform software object-manager switch ative f0 object <object ID> parent"

Por exemplo, para validar a Sobreposição (*,G)

Edge-1#show platform software object-manager switch active f0 object 100880 parents 
Object identifier: 100605
Description: ipv4_mcast table 2 (blue_vn), vrf id 2
Status: Done
Object identifier: 100878
Description: mlist 109
Status: Done

Para validar a Sobreposição (S,G)

Edge-1#show platform software object-manager switch active f0 object 161855 parents 
Object identifier: 100605
Description: ipv4_mcast table 2 (blue_vn), vrf id 2
Status: Done
Object identifier: 161854
Description: mlist 143
Status: Done

O mlist é uma combinação da interface de entrada (IIF) e da lista da interface de saída (OIL) separada do mroute em um objeto diferente. Para validar o mlist, use o comando "show platform software mlist switch ative f0 index <index>"

Edge-1#show platform software mlist switch active f0 index 109
Multicast List entries
OCE Flags:
NS - Negate Signalling; IC - Internal copy;
A - Accept; F - Forward;
OCE Type OCE Flags Interface 
--------------------------------------------------------------------------------------
0xf8000171 OBJ_ADJACENCY NS, A LISP0.4100 <-- Incoming Interface for (*,G)
0xf80001f1 OBJ_ADJACENCY NS, F Vlan1025   <-- Outgoing Interface for (S,G)

Edge-1#show platform software mlist switch active f0 index 143
Multicast List entries
OCE Flags:
NS - Negate Signalling; IC - Internal copy;
A - Accept; F - Forward;
OCE Type OCE Flags Interface 
--------------------------------------------------------------------------------------
0xf8000171 OBJ_ADJACENCY A LISP0.4100 <-- Outgoing Interface for (S,G)
0xf80001f1 OBJ_ADJACENCY NS, F Vlan1025 <-- Incoming Interface for (S,G)

Programação de hardware Mroute - FED

Para validar a Sobreposição (S,G), use o comando "show platform software fed switch ative ip mfib vrf <VN Name> <overlay group address> <Unicast Source>"

Edge-1#show platform software fed switch active ip mfib vrf blue_vn 239.0.0.5 10.47.7.3 
Multicast (S,G) Information
VRF : 2
Source Address : 10.47.7.3
HTM Handler : 0x7f0efe53a638
SI Handler : 0x7f0efe50ec68
DI Handler : 0x7f0efe530768
REP RI handler : 0x7f0efe5387e8
Flags : 
Packet count : 0
State : 4
RPF : 
LISP0.4100 A
OIF : 
Vlan1025 F NS
LISP0.4100 A
(Adj: 0xf8000171 )

 Para validar o Underlay (S,G), use o comando "show platform software fed switch ative ip mfib <underlay group address> <RLOC of FHR>"

Edge-1#show platform software fed switch active ip mfib 232.0.2.245 10.47.1.13 
Multicast (S,G) Information
VRF : 0
Source Address : 10.47.1.13
HTM Handler : 0x7f0efe512408
SI Handler : 0x7f0efe5158f8
DI Handler : 0x7f0efe525538
REP RI handler : 0x7f0efe52ca18
Flags : 
Packet count : 0
State : 4
RPF : 
GigabitEthernet1/0/2 A
OIF : 
LISP0 LISP Decap F NS
GigabitEthernet1/0/2 A

Em seguida, o Índice de destino (DI) é validado para a Sobreposição e a Sobreposição (S,G). Você pode usar o comando "show platform hardware fed switch ative fwd-asic abstraction print-resource-handle <Manipulador de DI> 1"

Para a sobreposição (S,G)

Edge-1#show platform hardware fed switch active fwd-asic abs print-resource-handle 0x7f0efe512408 1
Handle:0x7f0efe530768 Res-Type:ASIC_RSC_DI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1
priv_ri/priv_si Handle: (nil)Hardware Indices/Handles: index0:0x5279 mtu_index/l3u_ri_index0:0x0 index1:0x5279 mtu_index/l3u_ri_index1:0x0 
Cookie length: 56
00 00 00 00 00 00 00 00 02 00 00 00 03 07 2f 0a 05 00 00 ef 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Detailed Resource Information (ASIC_INSTANCE# 0)
----------------------------------------
Destination index = 0x5279 
pmap = 0x00000000 0x00000010
pmap_intf : [GigabitEthernet1/0/5] <-- From IGMP Snooping 
cmi = 0x0
rcp_pmap = 0x0
al_rsc_cmi
CPU Map Index (CMI) [0]
ctiLo0 = 0
ctiLo1 = 0
ctiLo2 = 0
cpuQNum0 = 0
cpuQNum1 = 0
cpuQNum2 = 0
npuIndex = 0
stripSeg = 0
copySeg = 0
Detailed Resource Information (ASIC_INSTANCE# 1)
----------------------------------------
Destination index = 0x5279 
pmap = 0x00000000 0x00000000
cmi = 0x0
rcp_pmap = 0x0
al_rsc_cmi
CPU Map Index (CMI) [0]
ctiLo0 = 0
ctiLo1 = 0
ctiLo2 = 0
cpuQNum0 = 0
cpuQNum1 = 0
cpuQNum2 = 0
npuIndex = 0
stripSeg = 0
copySeg = 0
==============================================================

Para a subjacência (S,G)

Edge-1#show platform hardware fed switch active fwd-asic abs print-resource-handle 0x7f0efe525538 1
Handle:0x7f0efe525538 Res-Type:ASIC_RSC_DI Res-Switch-Num:255 Asic-Num:255 Feature-ID:AL_FID_L3_MULTICAST_IPV4 Lkp-ftr-id:LKP_FEAT_INVALID ref_count:1Cookie length: 56
00 00 00 00 00 00 00 00 00 00 00 00 0d 01 2f 0a f5 02 00 e8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Detailed Resource Information (ASIC_INSTANCE# 0)
----------------------------------------
Destination index = 0x5284 
pmap = 0x00000000 0x00000000 <-- Expected since this is the Underlay, and recirculation is required to strip the VXLAN header
cmi = 0x0
rcp_pmap = 0x1 <-- Indicates recirculation is required
al_rsc_cmi
CPU Map Index (CMI) [0]
ctiLo0 = 0
ctiLo1 = 0
ctiLo2 = 0
cpuQNum0 = 0
cpuQNum1 = 0
cpuQNum2 = 0
npuIndex = 0
stripSeg = 0
copySeg = 0
Detailed Resource Information (ASIC_INSTANCE# 1)
----------------------------------------
Destination index = 0x5284 
pmap = 0x00000000 0x00000000
cmi = 0x0
rcp_pmap = 0x0
al_rsc_cmi
CPU Map Index (CMI) [0]
ctiLo0 = 0
ctiLo1 = 0
ctiLo2 = 0
cpuQNum0 = 0
cpuQNum1 = 0
cpuQNum2 = 0
npuIndex = 0
stripSeg = 0
copySeg = 0
==============================================================