Este documento fornece um exemplo de configuração para usuários remotos fazendo chamadas usando um dos métodos a seguir. Em cada caso, a rechamada é executada com o uso de uma chamada V.110.
Usuários conectando o 3640 via GSM e requisitando retorno da chamada.
Os usuários conectando o 3640 por meio de um modem e solicitando retorno de chamada.
Usuários se conectando ao 3640 via ISDN (dados) e solicitando um retorno de chamada.
Observação: a autenticação, autorização e contabilização (AAA) é configurada no roteador por padrão. Você também deve criar um usuário para fazer login.
Neste exemplo, também definimos a autenticação PPP (Point-to-Point Protocol) para chamada e chamada. Alteramos o script para configurar o modem para V.110 o tempo todo e para permitir que os usuários escolham seu método (modem ou GSM). Dependendo do método escolhido, os usuários devem:
use ZDTxxx no número de chamada de retorno (para modem).
use Dlxxxx no número de rechamada (para GSM).
Não existem requisitos específicos para este documento.
As informações neste documento são baseadas nestas versões de software e hardware:
O recurso de retorno de chamada V.110 está disponível no Rosa IOS? Software versão 12.2(5.2)T e superior.
Modem Software Versão 2.7.3.0.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.
Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.
Observação: para encontrar informações adicionais sobre os comandos usados neste documento, use a ferramenta Command Lookup Tool (somente clientes registrados).
Este documento utiliza a configuração de rede mostrada neste diagrama.
Este documento utiliza esta configuração:
suzanne
suzanne |
---|
suzanne#show running-config ! version 12.2 service internal ! hostname suzanne ! aaa new-model ! aaa authentication login default local aaa authentication ppp default local aaa authorization network default local aaa session-id common ! username ww password 0 username alainisdn password 0 username alaingsm callback-dialstring "" password 0 username alainmod callback-dialstring "" password 0 ! modem country mica belgium ! isdn switch-type primary-net5 isdn voice-call-failure 0 chat-script offhook "" "ATH1" OK chat-script callback ABORT ERROR ABORT BUSY "" "AT&F" OK "ATX3DT \T" TIMEOUT 90 \c chat-script callback1analog ABORT ERROR ABORT BUSY "" "AT&F" OK "ATDT \T" TIMEOUT 90 CONNECT \c chat-script callback2gsm ABORT ERROR ABORT BUSY "" "AT&F" OK "ATS29=8" OK "AT \T" TIMEOUT 90 CONNECT \c ! controller E1 1/0 pri-group timeslots 1-31 ! interface Ethernet0/0 ip address 172.17.243.105 255.255.255.0 ! interface Serial1/0:15 description E1 0451/39920 no ip address encapsulation ppp dialer rotary-group 1 isdn switch-type primary-net5 isdn incoming-voice modem isdn outgoing-voice info-transfer-capability 3.1kHz-audio no cdp enable ppp authentication chap callin ! interface BRI3/1 description belgacom 027202094 no ip address encapsulation ppp isdn switch-type basic-net3 isdn incoming-voice modem no cdp enable ! interface Group-Async1 ip unnumbered Dialer1 encapsulation ppp dialer in-band dialer callback-secure dialer-group 1 async dynamic routing async mode interactive peer default ip address pool pool ppp callback accept ppp authentication pap group-range 65 94 ! interface Dialer1 description Dial-In User ip address 172.31.1.1 255.255.0.0 ip helper-address 90.100.48.38 ip helper-address 90.100.60.202 encapsulation ppp dialer in-band dialer callback-secure dialer map ip 172.31.1.2 name alainisdn class callback 6136 peer default ip address pool pool no cdp enable ppp callback accept ppp authentication chap callin ! map-class dialer callback dialer callback-server username dialer-list 1 protocol ip permit ! line con 0 exec-timeout 0 0 password line 65 94 script dialer callback2gsm script callback callback2gsm modem InOut transport input telnet transport output pad v120 lapb-ta telnet rlogin udptn autoselect during-login autoselect ppp stopbits 1 flowcontrol hardware line aux 0 password line vty 0 4 exec-timeout 0 0 password ! end |
Esta seção fornece informações que você pode usar para confirmar se sua configuração está funcionando adequadamente.
A Output Interpreter Tool (somente clientes registrados) oferece suporte a determinados comandos show, o que permite exibir uma análise da saída do comando show.
show ip route????exibe o conteúdo da tabela de roteamento IP
Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.
Observação: antes de emitir os comandos debug, consulte Informações importantes sobre comandos debug.
debug modem —para observar a atividade da linha do modem em um servidor de acesso.
debug dialer events — exibe informações de debugação sobre os pacotes recebidos em uma interface de discador.
debug ppp authentication —exibe mensagens do protocolo de autenticação, incluindo trocas de pacotes CHAP (Challenge Authentication Protocol Protocolo de Autenticação de Desafio) e PAP (Password Authentication Protocol Protocolo de Autenticação de Senha).
debug ppp cbcp —exibe erros de protocolo e estatísticas associadas às negociações de conexão PPP usando o Protocolo de Controle de Chamada da Microsoft (MSCB - Microsoft Callback Control Protocol).
debug isdn q931 — exibe informações sobre configuração de chamada e subdivisão de conexões de rede ISDN (Camada 3) entre o roteador local (lado do usuário) e a rede.
debug chat —verifica se o script de bate-papo está funcionando corretamente.
debug callback —exibe eventos de retorno de chamada quando o roteador está usando um modem e um script de bate-papo para retornar a chamada em uma linha de terminal.
suzanne# 01:03:00: ISDN BR3/1: RX <- SETUP pd = 8 callref = 0x2F 01:03:00: Sending Complete 01:03:00: Bearer Capability i = 0x9090A3 01:03:00: Channel ID i = 0x89 01:03:00: Calling Party Number i = 0x21, 0x83, '478681006', Plan:ISDN, Type:National 01:03:00: Called Party Number i = 0xA1, '27202094', Plan:ISDN, Type:National 01:03:00: ISDN BR3/1: Event: Received a VOICE call from 478681006 on B1 at 64 Kb/s 01:03:00: ISDN BR3/1: Event: Accepting the call id 0x19 01:03:00: %ISDN-6-LAYER2UP: Layer 2 for Interface BR3/1, TEI 70 changed to up 01:03:00: ISDN BR3/1: TX -> CALL_PROC pd = 8 callref = 0xAF 01:03:00: Channel ID i = 0x89 01:03:00: ISDN BR3/1: TX -> ALERTING pd = 8 callref = 0xAF 01:03:00: ISDN BR3/1: TX -> CONNECT pd = 8 callref = 0xAF 01:03:01: ISDN BR3/1: RX <- CONNECT_ACK pd = 8 callref = 0x2F 01:03:01: Modem 2/12 Mica: configured for Answer mode, with Null signaling,0x0 tone detection. 01:03:01: Modem 2/12 Mica: in modem state CALL_SETUP 01:03:02: Modem 2/12 Mica: in modem state CONNECT 01:03:06: Modem 2/12 Mica: in modem state LINK 01:03:07: %ISDN-6-CONNECT: Interface BRI3/1:1 is now connected to 478681006 01:03:15: Modem 2/12 Mica: in modem state TRAINUP 01:03:17: Modem 2/12 Mica: in modem state EC_NEGOTIATING 01:03:18: Modem 2/12 Mica: in modem state STEADY 01:03:18: Modem 2/12 Mica: CONNECT at 31200/31200 (Tx/Rx), V34+, LAPM, None 01:03:19: TTY77: DSR came up 01:03:19: tty77: Modem: IDLE->(unknown) 01:03:19: TTY77: EXEC creation 01:03:19: TTY77: set timer type 10, 30 seconds 01:03:19: TTY77: Autoselect(2) sample 7E 01:03:19: TTY77: Autoselect(2) sample 7EFF 01:03:19: TTY77: Autoselect(2) sample 7EFF7D 01:03:19: TTY77: Autoselect(2) sample 7EFF7D23 01:03:19: TTY77 Autoselect cmd: ppp negotiate 01:03:19: TTY77: EXEC creation 01:03:19: TTY77: create timer type 1, 600 seconds 01:03:19: TTY77: destroy timer type 1 01:03:19: TTY77: no timer type 0 to destroy 01:03:19: As77 DDR: Dialer received incoming call from <unknown> 01:03:21: %LINK-3-UPDOWN: Interface Async77, changed state to up 01:03:21: As77 DDR: Dialer statechange to up 01:03:21: As77 DDR: Dialer received incoming call from <unknown> 01:03:21: As77 PPP: Treating connection as a callin 01:03:21: As77 PPP: Authorization required 01:03:22: Modem 2/12 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:03:22: As77 PPP: Authorization required 01:03:27: Modem 2/12 Mica: PPP escape_map: Tx map = A0000, Rx map = 0 01:03:27: As77 MCB: Initialize 01:03:27: MCB: Flush 01:03:27: Modem 2/12 Mica: Bad RX Frame: control = 0xE007, length = 0xD, buffer = 0x3BC6E54 01:03:30: As77 PAP: I AUTH-REQ id 2 len 16 from "alaingsm" 01:03:30: As77 PAP: Authenticating peer alaingsm 01:03:30: As77 PPP: Sent PAP LOGIN Request to AAA 01:03:30: As77 PPP: Received LOGIN Response from AAA = PASS 01:03:30: As77 DDR: Remote name for alaingsm 01:03:30: As77 DDR: Authenticated host alaingsm with no matching dialer map 01:03:30: As77 PAP: O AUTH-ACK id 2 len 5 01:03:30: As77 MCB: Start 01:03:30: As77 MCB: User alaingsm Callback Number - Client ANY 01:03:30: As77 MCB: Newstate 0-INIT -> 2-WAIT_RESPONSE 01:03:30: As77 MCB: O Request Id 1 Callback Type Client-Num delay 0 01:03:32: As77 MCB: Timeout in state WAIT_RESPONSE sending new Request 2 01:03:32: As77 MCB: O Request Id 2 Callback Type Client-Num delay 0 01:03:34: As77 MCB: Timeout in state WAIT_RESPONSE sending new Request 3 01:03:34: As77 MCB: O Request Id 3 Callback Type Client-Num delay 0 01:03:35: Async77 PPP: I MCB Response(2) id 1 len 22 01:03:35: Async77 MCB: I 2 1 0 16 2 12 F 1 44 49 30 30 34 37 38 36 38 31 30 30 36 0 01:03:35: As77 MCB: Received response 01:03:35: As77 MCB: Resp ignored. ID Expected 3, got id 1 01:03:36: As77 MCB: Timeout in state WAIT_RESPONSE sending new Request 4 01:03:36: As77 MCB: O Request Id 4 Callback Type Client-Num delay 0 01:03:36: Async77 PPP: I MCB Response(2) id 4 len 22 01:03:36: Async77 MCB: I 2 4 0 16 2 12 F 1 44 49 30 30 34 37 38 36 38 31 30 30 36 0 01:03:36: As77 MCB: Received response !--- You can see here that "DI00478681006" was entered at the user PC. 01:03:36: As77 MCB: Response CBK-Client-Num 2 18 15, addr 1-DI00478681006 01:03:36: As77 MCB: O Ack Id 5 Callback Type Client-Num delay 15 01:03:36: As77 MCB: Negotiated MCB with peer 01:03:36: As77 MCB: Newstate 2-WAIT_RESPONSE -> 3-WAIT_TERMINATE 01:03:37: As77 MCB: Peer terminating the link 01:03:37: As77 MCB: Newstate 3-WAIT_TERMINATE -> 5-WAIT_LINKDOWN 01:03:37: As77 MCB: Link terminated by peer, Callback Needed 01:03:37: As77 MCB: Newstate 5-WAIT_LINKDOWN -> 6-CALLING 01:03:37: As77 MCB: Initiate Callback for ^->o`iB@ at DI00478681006 using Async DDR 01:03:37: As77 DDR: PPP callback Callback server starting to alaingsm DI00478681006 01:03:37: As77 MCB: Dialer callback started !--- Call is disconnected. 01:03:38: Modem 2/12 Mica: in modem state SS_RETRAINING 01:03:38: ISDN BR3/1: RX <- DISCONNECT pd = 8 callref = 0x2F 01:03:38: Cause i = 0x8090 - Normal call clearing 01:03:38: Progress Ind i = 0x8088 - In-band info or appropriate now available 01:03:38: %ISDN-6-DISCONNECT: Interface BRI3/1:1 disconnected from 478681006, call lasted 37 seconds 01:03:38: ISDN BR3/1: TX -> RELEASE pd = 8 callref = 0xAF 01:03:38: Cause i = 0x8090 - Normal call clearing 01:03:38: Modem 2/12 Mica: in modem state TERMINATING 01:03:38: ISDN BR3/1: RX <- RELEASE_COMP pd = 8 callref = 0x2F 01:03:39: TTY77: Async Int reset: Dropping DTR 01:03:39: Modem 2/12 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:03:39: As77 PPP: Authorization required 01:03:40: Modem 2/12 Mica: in modem state IDLE 01:03:40: Modem 2/12 Mica: DISCONNECT after 00:00:38, due to reason (0xDF00) Host Disconnect. 01:03:40: TTY77: DSR was dropped 01:03:40: tty77: Modem: READY->(unknown) 01:03:41: TTY77: dropping DTR, hanging up 01:03:41: tty77: Modem: HANGUP->(unknown) 01:03:41: %LINK-5-CHANGED: Interface Async77, changed state to reset 01:03:42: TTY77: cleanup pending. Delaying DTR 01:03:43: TTY77: cleanup pending. Delaying DTR 01:03:44: TTY77: cleanup pending. Delaying DTR 01:03:44: TTY77: no timer type 0 to destroy 01:03:44: TTY77: no timer type 1 to destroy 01:03:44: TTY77: no timer type 3 to destroy 01:03:44: TTY77: no timer type 4 to destroy 01:03:44: TTY77: no timer type 2 to destroy 01:03:44: Async77: allowing modem_process to continue hangup 01:03:45: TTY77: restoring DTR 01:03:46: %LINK-3-UPDOWN: Interface Async77, changed state to down 01:03:53: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR3/1, TEI 70 changed to down !--- Callback is started. 01:03:56: As77 DDR: re-enable timeout 01:03:56: DDR: callback triggered by dialer_timers 01:03:56: As77 DDR: beginning callback to alaingsm DI00478681006 01:03:56: As77 DDR: Attempting to dial DI00478681006 01:03:56: CHAT77: Attempting async line dialer script 01:03:56: CHAT77: Dialing using Modem script: callback2gsm & System script: none 01:03:56: CHAT77: process started 01:03:56: CHAT77: Asserting DTR 01:03:56: CHAT77: Chat script callback2gsm started 01:03:56: CHAT77: Sending string: AT&F 01:03:56: CHAT77: Expecting string: OK 01:03:56: CHAT77: Completed match for expect: OK 01:03:56: CHAT77: Sending string: ATS29=8 01:03:56: CHAT77: Expecting string: OK 01:03:56: CHAT77: Completed match for expect: OK !--- We send DI00478681006 01:03:56: CHAT77: Sending string: AT \T<DI00478681006> 01:03:56: CHAT77: Expecting string: CONNECT 01:03:56: Modem 2/12 Mica: configured for Originate mode, with Null signaling, 0x1 tone detection. 01:03:56: Modem 2/12 Mica: received dialstring 00478681006 01:03:56: ISDN Se1/0:15: TX -> SETUP pd = 8 callref = 0x000E 01:03:56: Bearer Capability i = 0x8890214846BB 01:03:56: Channel ID i = 0xA9839F 01:03:56: Called Party Number i = 0x81, '00478681006', Plan:ISDN, Type:Unknown 01:03:56: Low Layer Compat i = 0x8890214846BB 01:03:56: ISDN Se1/0:15: RX <- CALL_PROC pd = 8 callref = 0x800E 01:03:56: Channel ID i = 0xA9839F 01:03:56: Modem 2/12 Mica: in modem state CALL_SETUP 01:04:02: ISDN Se1/0:15: RX <- ALERTING pd = 8 callref = 0x800E 01:04:03: ISDN Se1/0:15: RX <- CONNECT pd = 8 callref = 0x800E 01:04:03: ISDN Se1/0:15: TX -> CONNECT_ACK pd = 8 callref = 0x000E 01:04:03: Modem 2/12 Mica: in modem state CONNECT 01:04:03: Modem 2/12 Mica: in modem state LINK 01:04:03: Modem 2/12 Mica: in modem state TRAINUP 01:04:03: Modem 2/12 Mica: in modem state EC_NEGOTIATING 01:04:03: Modem 2/12 Mica: in modem state STEADY 01:04:03: CHAT77: Completed match for expect: CONNECT 01:04:03: CHAT77: Sending string: \c 01:04:03: CHAT77: Chat script callback2gsm finished, status = Success 01:04:03: TTY77: no timer type 1 to destroy 01:04:03: TTY77: no timer type 0 to destroy 01:04:03: Modem 2/12 Mica: CONNECT at 9600/9600 (Tx/Rx), V110, V.110, None 01:04:04: As77 PPP: Treating connection as a callout 01:04:04: Modem 2/12 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:04:04: As77 PPP: Authorization required 01:04:04: %LINK-3-UPDOWN: Interface Async77, changed state to up 01:04:04: As77 DDR: Dialer statechange to up 01:04:04: As77 DDR: Copying MS callback dialstring DI00478681006 to ddb 01:04:04: DDR: Freeing callback to alaingsm DI00478681006 01:04:04: As77 DDR: Dialer call has been placed 01:04:08: Modem 2/12 Mica: PPP escape_map: Tx map = A0000, Rx map = 0 01:04:08: As77 MCB: Initialize 01:04:08: Modem 2/12 Mica: Bad RX Frame: control = 0xE007, length = 0xD, buffer = 0x3BC6E54 01:04:09: %ISDN-6-CONNECT: Interface Serial1/0:30 is now connected to 00478681006 01:04:11: As77 PAP: I AUTH-REQ id 2 len 16 from "alaingsm" 01:04:11: As77 PAP: Authenticating peer alaingsm 01:04:11: As77 PPP: Sent PAP LOGIN Request to AAA 01:04:11: As77 PPP: Received LOGIN Response from AAA = PASS 01:04:11: As77 DDR: Remote name for alaingsm 01:04:11: As77 DDR: Authenticated host alaingsm with no matching dialer map 01:04:11: As77 PAP: O AUTH-ACK id 2 len 5 01:04:13: As77 DDR: dialer protocol up suzanne#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is 172.17.243.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.243.0 is directly connected, Ethernet0/0 172.31.0.0/16 is variably subnetted, 2 subnets, 2 masks C 172.31.1.28/32 is directly connected, Async77 C 172.31.0.0/16 is directly connected, Dialer1 S* 0.0.0.0/0 [1/0] via 172.17.243.1 suzanne#ping 172.31.1.28 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.28, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 784/858/880 ms suzanne# 01:04:49: ISDN Se1/0:15: RX <- DISCONNECT pd = 8 callref = 0x800E 01:04:49: Cause i = 0x8090 - Normal call clearing 01:04:49: %ISDN-6-DISCONNECT: Interface Serial1/0:30 disconnected from 00478681006, call lasted 46 seconds 01:04:49: ISDN Se1/0:15: TX -> RELEASE pd = 8 callref = 0x000E 01:04:49: Modem 2/12 Mica: in modem state TERMINATING 01:04:49: ISDN Se1/0:15: RX <- RELEASE_COMP pd = 8 callref = 0x800E 01:04:49: Modem 2/12 Mica: in modem state IDLE 01:04:49: Modem 2/12 Mica: DISCONNECT after 00:00:46, due to reason (0xDF00) Host Disconnect. 01:04:50: TTY77: DSR was dropped 01:04:50: tty77: Modem: READY->(unknown) 01:04:51: TTY77: Async Int reset: Dropping DTR 01:04:51: Modem 2/12 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:04:51: As77 PPP: Authorization required 01:04:51: TTY77: dropping DTR, hanging up 01:04:51: tty77: Modem: HANGUP->(unknown) 01:04:52: TTY77: cleanup pending. Delaying DTR 01:04:53: %LINK-5-CHANGED: Interface Async77, changed state to reset 01:04:53: TTY77: cleanup pending. Delaying DTR 01:04:54: TTY77: cleanup pending. Delaying DTR 01:04:55: TTY77: cleanup pending. Delaying DTR 01:04:56: TTY77: no timer type 0 to destroy 01:04:56: TTY77: no timer type 1 to destroy 01:04:56: TTY77: no timer type 3 to destroy 01:04:56: TTY77: no timer type 4 to destroy 01:04:56: TTY77: no timer type 2 to destroy 01:04:56: Async77: allowing modem_process to continue hangup 01:04:56: TTY77: restoring DTR 01:04:58: %LINK-3-UPDOWN: Interface Async77, changed state to down 01:05:08: As77 DDR: re-enable timeout
!--- Modem callback using default of MICA (modem dialing US robotics). suzanne# 01:06:21: ISDN Se1/0:15: RX <- SETUP pd = 8 callref = 0x6D73 01:06:21: Sending Complete 01:06:21: Bearer Capability i = 0x9090A3 01:06:21: Channel ID i = 0xA18387 01:06:21: Progress Ind i = 0x8183 - Origination address is non-ISDN 01:06:21: Calling Party Number i = 0xA1, '6020', Plan:ISDN, Type:National 01:06:21: Called Party Number i = 0x81, '214', Plan:ISDN, Type:Unknown 01:06:21: ISDN Se1/0:15: TX -> CALL_PROC pd = 8 callref = 0xED73 01:06:21: Channel ID i = 0xA98387 01:06:21: ISDN Se1/0:15: TX -> ALERTING pd = 8 callref = 0xED73 01:06:21: ISDN Se1/0:15: TX -> CONNECT pd = 8 callref = 0xED73 01:06:21: ISDN Se1/0:15: RX <- CONNECT_ACK pd = 8 callref = 0x6D73 01:06:21: ISDN Se1/0:15: CALL_PROGRESS: CALL_CONNECTED call id 0x1A, bchan 6, dsl 0 01:06:21: Modem 2/13 Mica: configured for Answer mode, with Null signaling, 0x0 tone detection. 01:06:21: Modem 2/13 Mica: in modem state CALL_SETUP 01:06:22: Modem 2/13 Mica: in modem state CONNECT 01:06:26: Modem 2/13 Mica: in modem state LINK 01:06:27: %ISDN-6-CONNECT: Interface Serial1/0:6 is now connected to 6020 01:06:34: Modem 2/13 Mica: in modem state TRAINUP 01:06:36: Modem 2/13 Mica: in modem state EC_NEGOTIATING 01:06:36: Modem 2/13 Mica: in modem state STEADY 01:06:36: Modem 2/13 Mica: CONNECT at 9600/9600 (Tx/Rx), V34+, LAPM, None 01:06:37: TTY78: DSR came up 01:06:37: tty78: Modem: IDLE->(unknown) 01:06:37: TTY78: EXEC creation 01:06:37: TTY78: set timer type 10, 30 seconds 01:06:40: TTY78: Autoselect(2) sample 7E 01:06:40: TTY78: Autoselect(2) sample 7EFF 01:06:40: TTY78: Autoselect(2) sample 7EFF7D 01:06:40: TTY78: Autoselect(2) sample 7EFF7D23 01:06:40: TTY78 Autoselect cmd: ppp negotiate 01:06:40: TTY78: EXEC creation 01:06:40: TTY78: create timer type 1, 600 seconds 01:06:40: TTY78: destroy timer type 1 01:06:40: TTY78: no timer type 0 to destroy 01:06:40: As78 DDR: Dialer received incoming call from <unknown> 01:06:42: %LINK-3-UPDOWN: Interface Async78, changed state to up 01:06:42: As78 DDR: Dialer statechange to up 01:06:42: As78 DDR: Dialer received incoming call from <unknown> 01:06:42: As78 PPP: Treating connection as a callin 01:06:42: As78 PPP: Authorization required 01:06:43: Modem 2/13 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:06:43: As78 PPP: Authorization required 01:06:47: Modem 2/13 Mica: PPP escape_map: Tx map = A0000, Rx map = 0 01:06:47: As78 MCB: Initialize 01:06:47: MCB: Flush 01:06:47: Modem 2/13 Mica: Bad RX Frame: control = 0xE007, length = 0xE, buffer = 0x3BC9014 01:06:50: As78 PAP: I AUTH-REQ id 2 len 16 from "alainmod" 01:06:50: As78 PAP: Authenticating peer alainmod 01:06:50: As78 PPP: Sent PAP LOGIN Request to AAA 01:06:50: As78 PPP: Received LOGIN Response from AAA = PASS 01:06:50: As78 DDR: Remote name for alainmod 01:06:50: As78 DDR: Authenticated host alainmod with no matching dialer map 01:06:50: As78 PAP: O AUTH-ACK id 2 len 5 01:06:50: As78 MCB: Start 01:06:50: As78 MCB: User alainmod Callback Number - Client ANY 01:06:50: As78 MCB: Newstate 0-INIT -> 2-WAIT_RESPONSE 01:06:50: As78 MCB: O Request Id 1 Callback Type Client-Num delay 0 01:06:52: As78 MCB: Timeout in state WAIT_RESPONSE sending new Request 2 01:06:52: As78 MCB: O Request Id 2 Callback Type Client-Num delay 0 01:06:54: As78 MCB: Timeout in state WAIT_RESPONSE sending new Request 3 01:06:54: As78 MCB: O Request Id 3 Callback Type Client-Num delay 0 01:06:54: Async78 PPP: I MCB Response(2) id 1 len 17 01:06:54: Async78 MCB: I 2 1 0 11 2 D F 1 5A 44 54 20 36 30 32 30 0 01:06:54: As78 MCB: Received response 01:06:54: As78 MCB: Resp ignored. ID Expected 3, got id 1 01:06:56: As78 MCB: Timeout in state WAIT_RESPONSE sending new Request 4 01:06:56: As78 MCB: O Request Id 4 Callback Type Client-Num delay 0 01:06:56: Async78 PPP: I MCB Response(2) id 4 len 17 01:06:56: Async78 MCB: I 2 4 0 11 2 D F 1 5A 44 54 20 36 30 32 30 0 01:06:56: As78 MCB: Received response 01:06:56: As78 MCB: Response CBK-Client-Num 2 13 15, addr 1-ZDT 6020 01:06:56: As78 MCB: O Ack Id 5 Callback Type Client-Num delay 15 01:06:56: As78 MCB: Negotiated MCB with peer 01:06:56: As78 MCB: Newstate 2-WAIT_RESPONSE -> 3-WAIT_TERMINATE 01:06:56: As78 MCB: Peer terminating the link 01:06:56: As78 MCB: Newstate 3-WAIT_TERMINATE -> 5-WAIT_LINKDOWN 01:06:56: As78 MCB: Link terminated by peer, Callback Needed 01:06:56: As78 MCB: Newstate 5-WAIT_LINKDOWN -> 6-CALLING 01:06:56: As78 MCB: Initiate Callback for ^->o`iB@ at ZDT 6020 using Async DDR 01:06:56: As78 DDR: PPP callback Callback server starting to alainmod ZDT 6020 01:06:56: As78 MCB: Dialer callback started 01:06:57: Modem 2/13 Mica: in modem state TERMINATING 01:06:57: Modem 2/13 Mica: in modem state IDLE 01:06:57: %ISDN-6-DISCONNECT: Interface Serial1/0:6 disconnected from 6020, call lasted 36 seconds 01:06:57: ISDN Se1/0:15: TX -> DISCONNECT pd = 8 callref = 0xED73 01:06:57: Cause i = 0x8090 - Normal call clearing 01:06:57: Modem 2/13 Mica: DISCONNECT after 00:00:35, due to reason (0x8220) EC rcvd DISC frame. 01:06:57: TTY78: DSR was dropped 01:06:57: tty78: Modem: READY->(unknown) 01:06:57: ISDN Se1/0:15: RX <- RELEASE pd = 8 callref = 0x6D73 01:06:57: ISDN Se1/0:15: TX -> RELEASE_COMP pd = 8 callref = 0xED73 01:06:58: TTY78: dropping DTR, hanging up 01:06:58: TTY78: Async Int reset: Dropping DTR 01:06:58: tty78: Modem: HANGUP->(unknown) 01:06:59: TTY78: cleanup pending. Delaying DTR 01:06:59: Modem 2/13 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:06:59: As78 PPP: Authorization required 01:07:00: %LINK-5-CHANGED: Interface Async78, changed state to reset 01:07:00: TTY78: cleanup pending. Delaying DTR 01:07:01: TTY78: cleanup pending. Delaying DTR 01:07:02: TTY78: cleanup pending. Delaying DTR 01:07:03: TTY78: no timer type 0 to destroy 01:07:03: TTY78: no timer type 1 to destroy 01:07:03: TTY78: no timer type 3 to destroy 01:07:03: TTY78: no timer type 4 to destroy 01:07:03: TTY78: no timer type 2 to destroy 01:07:03: Async78: allowing modem_process to continue hangup 01:07:03: TTY78: restoring DTR 01:07:05: %LINK-3-UPDOWN: Interface Async78, changed state to down 01:07:15: As78 DDR: re-enable timeout !--- Callback start. 01:07:15: DDR: callback triggered by dialer_timers 01:07:15: As78 DDR: beginning callback to alainmod ZDT 6020 01:07:15: As78 DDR: Attempting to dial ZDT 6020 01:07:15: CHAT78: Attempting async line dialer script 01:07:15: CHAT78: Dialing using Modem script: callback2gsm & System script: none 01:07:15: CHAT78: process started 01:07:15: CHAT78: Asserting DTR 01:07:15: CHAT78: Chat script callback2gsm started 01:07:15: CHAT78: Sending string: AT&F 01:07:15: CHAT78: Expecting string: OK 01:07:15: CHAT78: Completed match for expect: OK 01:07:15: CHAT78: Sending string: ATS29=8 01:07:15: CHAT78: Expecting string: OK 01:07:15: CHAT78: Completed match for expect: OK !--- The user entered "ZDT 6020". This is what we send: 01:07:15: CHAT78: Sending string: AT \T<ZDT 6020> 01:07:15: CHAT78: Expecting string: CONNECT 01:07:15: Modem 2/13 Mica: configured for Originate mode, with Null signaling, 0x1 tone detection. 01:07:15: Modem 2/13 Mica: received dialstring 6020 01:07:15: ISDN Se1/0:15: TX -> SETUP pd = 8 callref = 0x000F 01:07:15: Bearer Capability i = 0x9090A3 01:07:15: Channel ID i = 0xA9839F 01:07:15: Called Party Number i = 0x81, '6020', Plan:ISDN, Type:Unknown 01:07:15: ISDN Se1/0:15: RX <- CALL_PROC pd = 8 callref = 0x800F 01:07:15: Channel ID i = 0xA9839F 01:07:15: ISDN Se1/0:15: RX <- ALERTING pd = 8 callref = 0x800F 01:07:15: Modem 2/13 Mica: in modem state CALL_SETUP 01:07:16: Modem 2/13 Mica: Detected Dial tone 01:07:17: ISDN Se1/0:15: RX <- CONNECT pd = 8 callref = 0x800F 01:07:17: Progress Ind i = 0x8182 - Destination address is non-ISDN 01:07:17: Connected Number i = 0xA136303230 01:07:17: ISDN Se1/0:15: TX -> CONNECT_ACK pd = 8 callref = 0x000F 01:07:17: Modem 2/13 Mica: in modem state CONNECT 01:07:19: Modem 2/13 Mica: in modem state LINK 01:07:23: %ISDN-6-CONNECT: Interface Serial1/0:30 is now connected to 6020 01:07:26: Modem 2/13 Mica: in modem state TRAINUP 01:07:28: Modem 2/13 Mica: in modem state EC_NEGOTIATING 01:07:28: Modem 2/13 Mica: in modem state STEADY 01:07:28: CHAT78: Completed match for expect: CONNECT 01:07:28: CHAT78: Sending string: \c 01:07:28: CHAT78: Chat script callback2gsm finished, status = Success 01:07:28: TTY78: no timer type 1 to destroy 01:07:28: TTY78: no timer type 0 to destroy 01:07:28: Modem 2/13 Mica: CONNECT at 33600/31200 (Tx/Rx), V34+, LAPM, None 01:07:28: As78 PPP: Treating connection as a callout 01:07:28: Modem 2/13 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:07:28: As78 PPP: Authorization required 01:07:28: %LINK-3-UPDOWN: Interface Async78, changed state to up 01:07:28: As78 DDR: Dialer statechange to up 01:07:28: As78 DDR: Copying MS callback dialstring ZDT 6020 to ddb 01:07:28: DDR: Freeing callback to alainmod ZDT 6020 01:07:28: As78 DDR: Dialer call has been placed 01:07:29: Modem 2/13 Mica: PPP escape_map: Tx map = A0000, Rx map = 0 01:07:29: As78 MCB: Initialize 01:07:29: As78 PAP: I AUTH-REQ id 1 len 16 from "alainmod" 01:07:29: As78 PAP: Authenticating peer alainmod 01:07:29: As78 PPP: Sent PAP LOGIN Request to AAA 01:07:29: As78 PPP: Received LOGIN Response from AAA = PASS 01:07:29: As78 DDR: Remote name for alainmod 01:07:29: As78 DDR: Authenticated host alainmod with no matching dialer map 01:07:29: As78 PAP: O AUTH-ACK id 1 len 5 01:07:29: As78 DDR: dialer protocol up 01:07:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async78, changed state to up suzanne#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is 172.17.243.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.243.0 is directly connected, Ethernet0/0 172.31.0.0/16 is variably subnetted, 2 subnets, 2 masks C 172.31.1.19/32 is directly connected, Async78 C 172.31.0.0/16 is directly connected, Dialer1 S* 0.0.0.0/0 [1/0] via 172.17.243.1 suzanne#ping 172.31.1.19 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.19, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 356/372/396 ms suzanne# 01:08:08: Modem 2/13 Mica: in modem state TERMINATING 01:08:08: Modem 2/13 Mica: in modem state IDLE 01:08:08: Modem 2/13 Mica: DISCONNECT after 00:00:51, due to reason (0x8220) EC rcvd DISC frame. 01:08:08: %ISDN-6-DISCONNECT: Interface Serial1/0:30 disconnected from 6020, call lasted 51 seconds 01:08:08: ISDN Se1/0:15: TX -> DISCONNECT pd = 8 callref = 0x000F 01:08:08: Cause i = 0x8090 - Normal call clearing 01:08:08: ISDN Se1/0:15: RX <- RELEASE pd = 8 callref = 0x800F 01:08:08: ISDN Se1/0:15: TX -> RELEASE_COMP pd = 8 callref = 0x000F 01:08:09: TTY78: DSR was dropped 01:08:09: tty78: Modem: READY->(unknown) 01:08:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async78, changed state to down 01:08:10: TTY78: dropping DTR, hanging up 01:08:10: TTY78: Async Int reset: Dropping DTR 01:08:10: tty78: Modem: HANGUP->(unknown) 01:08:10: Modem 2/13 Mica: PPP escape_map: Tx map = FFFFFFFF, Rx map = 0 01:08:10: As78 PPP: Authorization required 01:08:11: TTY78: cleanup pending. Delaying DTR 01:08:12: %LINK-5-CHANGED: Interface Async78, changed state to reset 01:08:12: TTY78: cleanup pending. Delaying DTR 01:08:13: TTY78: cleanup pending. Delaying DTR 01:08:14: TTY78: cleanup pending. Delaying DTR 01:08:15: TTY78: no timer type 0 to destroy 01:08:15: TTY78: no timer type 1 to destroy 01:08:15: TTY78: no timer type 3 to destroy 01:08:15: TTY78: no timer type 4 to destroy 01:08:15: TTY78: no timer type 2 to destroy 01:08:15: Async78: allowing modem_process to continue hangup 01:08:15: TTY78: restoring DTR 01:08:17: %LINK-3-UPDOWN: Interface Async78, changed state to down 01:08:27: As78 DDR: re-enable timeout
!--- Receive call. suzanne# 01:09:00: ISDN Se1/0:15: RX <- SETUP pd = 8 callref = 0x6F28 01:09:00: Sending Complete 01:09:00: Bearer Capability i = 0x8890 01:09:00: Channel ID i = 0xA18388 01:09:00: Calling Party Number i = 0xA1, '6136', Plan:ISDN, Type:National 01:09:00: Called Party Number i = 0x81, '214', Plan:ISDN, Type:Unknown 01:09:00: %LINK-3-UPDOWN: Interface Serial1/0:7, changed state to up 01:09:00: ISDN Se1/0:15: TX -> CALL_PROC pd = 8 callref = 0xEF28 01:09:00: Channel ID i = 0xA98388 01:09:00: ISDN Se1/0:15: TX -> CONNECT pd = 8 callref = 0xEF28 01:09:00: Channel ID i = 0xA98388 01:09:00: Se1/0:7 PPP: Treating connection as a callin 01:09:00: Se1/0:7 PPP: Authorization required 01:09:00: ISDN Se1/0:15: RX <- CONNECT_ACK pd = 8 callref = 0x6F28 01:09:00: ISDN Se1/0:15: CALL_PROGRESS: CALL_CONNECTED call id 0x1B, bchan 7, dsl 0 01:09:01: Se1/0:7 PPP: Authorization required 01:09:01: Se1/0:7 MCB: Initialize 01:09:01: Se1/0:7 CHAP: O CHALLENGE id 1 len 28 from "suzanne" 01:09:01: Se1/0:7 CHAP: I RESPONSE id 1 len 30 from "alainisdn" 01:09:01: Se1/0:7 PPP: Sent CHAP LOGIN Request to AAA 01:09:01: Se1/0:7 PPP: Received LOGIN Response from AAA = PASS 01:09:01: Se1/0:7 DDR: Remote name for alainisdn 01:09:01: Se1/0:7 CHAP: O SUCCESS id 1 len 4 01:09:01: Se1/0:7 DDR: PPP callback Callback server starting to alainisdn 6136 01:09:01: Se1/0:7 DDR: disconnecting call 01:09:01: %ISDN-6-CONNECT: Interface Serial1/0:7 is now connected to 6136 alainisdn 01:09:01: ISDN Se1/0:15: TX -> DISCONNECT pd = 8 callref = 0xEF28 01:09:01: Cause i = 0x8090 - Normal call clearing 01:09:01: ISDN Se1/0:15: RX <- RELEASE pd = 8 callref = 0x6F28 01:09:01: %LINK-3-UPDOWN: Interface Serial1/0:7, changed state to down 01:09:01: ISDN Se1/0:15: TX -> RELEASE_COMP pd = 8 callref = 0xEF28 01:09:01: Se1/0:7 DDR: disconnecting call 01:09:02: ISDN Se1/0:15: RX <- SETUP pd = 8 callref = 0x70DF 01:09:02: Sending Complete 01:09:02: Bearer Capability i = 0x8890 01:09:02: Channel ID i = 0xA18389 01:09:02: Calling Party Number i = 0xA1, '6136', Plan:ISDN, Type:National 01:09:02: Called Party Number i = 0x81, '214', Plan:ISDN, Type:Unknown 01:09:02: %LINK-3-UPDOWN: Interface Serial1/0:8, changed state to up 01:09:02: ISDN Se1/0:15: TX -> CALL_PROC pd = 8 callref = 0xF0DF 01:09:02: Channel ID i = 0xA98389 01:09:02: ISDN Se1/0:15: TX -> CONNECT pd = 8 callref = 0xF0DF 01:09:02: Channel ID i = 0xA98389 01:09:02: Se1/0:8 PPP: Treating connection as a callin 01:09:02: Se1/0:8 PPP: Authorization required 01:09:02: ISDN Se1/0:15: RX <- CONNECT_ACK pd = 8 callref = 0x70DF 01:09:02: ISDN Se1/0:15: CALL_PROGRESS: CALL_CONNECTED call id 0x1C, bchan 8, dsl 0 01:09:02: Se1/0:8 PPP: Authorization required 01:09:03: Se1/0:8 MCB: Initialize 01:09:03: Se1/0:8 CHAP: O CHALLENGE id 1 len 28 from "suzanne" 01:09:03: Se1/0:8 CHAP: I RESPONSE id 1 len 30 from "alainisdn" 01:09:03: Se1/0:8 PPP: Sent CHAP LOGIN Request to AAA 01:09:03: Se1/0:8 PPP: Received LOGIN Response from AAA = PASS 01:09:03: Se1/0:8 DDR: Remote name for alainisdn 01:09:03: Se1/0:8 CHAP: O SUCCESS id 1 len 4 01:09:03: Se1/0:8 DDR: callback to alainisdn already started 01:09:03: Se1/0:8 DDR: disconnecting call 01:09:03: %ISDN-6-CONNECT: Interface Serial1/0:8 is now connected to 6136 alainisdn 01:09:03: ISDN Se1/0:15: TX -> DISCONNECT pd = 8 callref = 0xF0DF 01:09:03: Cause i = 0x8090 - Normal call clearing 01:09:03: ISDN Se1/0:15: RX <- RELEASE pd = 8 callref = 0x70DF 01:09:03: %LINK-3-UPDOWN: Interface Serial1/0:8, changed state to down 01:09:03: ISDN Se1/0:15: TX -> RELEASE_COMP pd = 8 callref = 0xF0DF 01:09:03: Se1/0:8 DDR: disconnecting call !--- Callback Start 01:09:16: DDR: Callback timer expired 01:09:16: Di1 DDR: beginning callback to alainisdn 6136 01:09:16: Se1/0:15 DDR: rotor dialout [priority] 01:09:16: Se1/0:15 DDR: Attempting to dial 6136 01:09:16: ISDN Se1/0:15: TX -> SETUP pd = 8 callref = 0x0010 01:09:16: Bearer Capability i = 0x8890 01:09:16: Channel ID i = 0xA9839F 01:09:16: Called Party Number i = 0x81, '6136', Plan:ISDN, Type:Unknown 01:09:16: ISDN Se1/0:15: RX <- CALL_PROC pd = 8 callref = 0x8010 01:09:16: Channel ID i = 0xA9839F 01:09:16: ISDN Se1/0:15: RX <- ALERTING pd = 8 callref = 0x8010 01:09:16: ISDN Se1/0:15: RX <- CONNECT pd = 8 callref = 0x8010 01:09:16: Connected Number i = 0xA136313336 01:09:16: %LINK-3-UPDOWN: Interface Serial1/0:30, changed state to up 01:09:16: DDR: Freeing callback to alainisdn 6136 01:09:16: ISDN Se1/0:15: TX -> CONNECT_ACK pd = 8 callref = 0x0010 01:09:16: Se1/0:30 PPP: Treating connection as a callout 01:09:16: Se1/0:30 PPP: Authorization required 01:09:16: Se1/0:30 MCB: Initialize 01:09:16: Se1/0:30 CHAP: I CHALLENGE id 7 len 30 from "alainisdn" 01:09:16: Se1/0:30 PPP: Sent CHAP SENDAUTH Request to AAA 01:09:16: Se1/0:30 PPP: Received SENDAUTH Response from AAA = PASS 01:09:16: Se1/0:30 CHAP: O RESPONSE id 7 len 28 from "suzanne" 01:09:16: Se1/0:30 CHAP: I SUCCESS id 7 len 4 01:09:16: Se1/0:30 PPP: Sent LCP AUTHOR Request to AAA 01:09:16: Se1/0:30 PPP: Sent IPCP AUTHOR Request to AAA 01:09:16: Se1/0:30 LCP: Received AAA AUTHOR Response = PASS 01:09:16: Se1/0:30 IPCP: Received AAA AUTHOR Response = PASS 01:09:16: Se1/0:30 DDR: dialer protocol up 01:09:17: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:30, changed state to up 01:09:22: %ISDN-6-CONNECT: Interface Serial1/0:30 is now connected to 6136 alainisdn suzanne# suzanne#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is 172.17.243.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.243.0 is directly connected, Ethernet0/0 172.31.0.0/16 is variably subnetted, 2 subnets, 2 masks C 172.31.1.2/32 is directly connected, Dialer1 C 172.31.0.0/16 is directly connected, Dialer1 S* 0.0.0.0/0 [1/0] via 172.17.243.1 suzanne#ping 172.31.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/34/36 ms suzanne#
Revisão | Data de publicação | Comentários |
---|---|---|
1.0 |
14-Sep-2005 |
Versão inicial |