Este documento fornece um exemplo de configuração para DMVPN (Hub-and-Spoke Dynamic Multipoint VPN) usando GRE (encapsulamento de roteamento genérico) sobre IPSec com protocolo EIGRP, NAT e CBAC.
Antes que um GRE multiponto (mGRE) e um túnel de IPSec possam ser estabelecidos, é necessário definir uma política de Intercâmbio de chave de Internet (IKE) utilizando o comando crypto isakmp policy.
Observação: para encontrar informações adicionais sobre os comandos usados neste documento, use a ferramenta Command Lookup Tool (somente clientes registrados).
As informações neste documento são baseadas nestas versões de software e hardware:
Software Cisco IOS® versão 12.2(15)T1 no roteador do hub e 12.3(1.6) nos roteadores spoke
Cisco 3620 como roteador de hub, dois Cisco 1720 Routers e um Cisco 3620 Router como roteadores spoke
As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. All of the devices used in this document started with a cleared (default) configuration. Se você estiver trabalhando em uma rede ativa, certifique-se de que entende o impacto potencial de qualquer comando antes de utilizá-lo.
Para obter mais informações sobre convenções de documento, consulte as Convenções de dicas técnicas Cisco.
Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.
Observação: para encontrar informações adicionais sobre os comandos usados neste documento, use a ferramenta Command Lookup Tool (somente clientes registrados).
Este documento utiliza a instalação de rede mostrada no diagrama abaixo.
Este documento utiliza as configurações mostradas abaixo.
Hub - 3620-B |
---|
3620-B#write terminal Building configuration... Current configuration : 2607 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname 3620-B ! logging queue-limit 100 ! memory-size iomem 10 ip subnet-zero ! ! ip cef no ip domain lookup ! !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out ftp ip inspect name in2out tftp ip inspect name in2out tcp timeout 43200 ip inspect name in2out http ip inspect name in2out udp ip audit po max-events 100 ! ! ! !--- Create an Internet Security Association and Key Management !--- Protocol (ISAKMP) policy for Phase 1 negotiations. ! crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. !--- Here "dmvpn" is the word that is used as the key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 crypto isakmp nat keepalive 20 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.117.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description MULTI-POINT GRE TUNNEL for BRANCHES bandwidth 1000 ip address 172.16.0.1 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map multicast dynamic ip nhrp network-id 99 ip nhrp holdtime 300 no ip split-horizon eigrp 1 no ip mroute-cache delay 1000 tunnel source FastEthernet0/0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! !--- This is the outside interface. interface FastEthernet0/0 ip address 14.24.117.1 255.255.0.0 ip nat outside ip access-group 100 in ip inspect in2out out no ip mroute-cache duplex auto speed auto ! interface Serial0/0 no ip address shutdown clockrate 2000000 no fair-queue ! interface FastEthernet0/1 no ip address no ip mroute-cache duplex auto speed auto ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks over the tunnels. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.117.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out FastEthernet0/0. ip nat inside source list 110 interface FastEthernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ip route 2.0.0.0 255.0.0.0 14.24.121.1 ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open other inbound access as needed. access-list 100 permit udp any host 14.24.117.1 eq 500 access-list 100 permit esp any host 14.24.117.1 access-list 100 permit gre any host 14.24.117.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.117.0 0.0.0.255 any ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! ! end 3620-B# |
Spoke 1 - 3620-A |
---|
3620-A#write terminal Building configuration... Current configuration : 2559 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 3620-A ! boot system flash slot0:c3620-ik9o3s7-mz.122-15.T1.bin logging queue-limit 100 ! memory-size iomem 15 ip subnet-zero ! ! ip cef no ip domain lookup ! !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.118.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.2 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip mroute-cache delay 1000 tunnel source Ethernet0/0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! !--- This is the outside interface. interface Ethernet0/0 ip address 14.24.118.1 255.255.0.0 ip nat outside ip inspect in2out out ip access-group 100 in no ip mroute-cache half-duplex ! interface Ethernet0/1 no ip address half-duplex ! interface Ethernet0/2 no ip address shutdown half-duplex ! interface Ethernet0/3 no ip address shutdown half-duplex ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks over the tunnel. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.118.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out Ethernet0/0. ip nat inside source list 110 interface Ethernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed. access-list 100 permit udp any host 14.24.118.1 eq 500 access-list 100 permit esp any host 14.24.118.1 access-list 100 permit gre any host 14.24.118.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.118.0 0.0.0.255 any ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! ! end 3620-A# |
Spoke 2 - 1720-b |
---|
1720-b#write terminal Building configuration... Current configuration : 2543 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 1720-b ! boot system flash flash:c1700-ny-mz.122-8.YJ logging queue-limit 100 enable password cisco ! username 7206-B password 0 cisco ip subnet-zero ! ! no ip domain lookup ! ip cef !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! vpdn-group 1 request-dialin protocol pppoe ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.116.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.3 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip mroute-cache delay 1000 tunnel source Dialer1 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! interface Ethernet0 no ip address half-duplex ! interface FastEthernet0 no ip address no ip mroute-cache speed auto pppoe enable pppoe-client dial-pool-number 1 ! !--- This is the outside interface. interface Dialer1 ip address 2.2.2.10 255.255.255.0 ip inspect in2out out ip access-group 100 in encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication pap chap callin ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.116.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out Dialer1. ip nat inside source list 110 interface Dialer1 overload ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed. access-list 100 permit udp any host 14.24.116.1 eq 500 access-list 100 permit esp any host 14.24.116.1 access-list 100 permit gre any host 14.24.116.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.116.0 0.0.0.255 any dialer-list 1 protocol ip permit ! ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! no scheduler allocate end 1720-b# |
Pontos remotos 3 - 1720-A |
---|
1720-A#write terminal Building configuration... Current configuration : 1770 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname 1720-A ! logging queue-limit 100 ! memory-size iomem 25 ip subnet-zero ! ! ! ip cef !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.120.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.4 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip mroute-cache delay 1000 tunnel source FastEthernet0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! interface Ethernet0 no ip address no ip mroute-cache half-duplex ! !--- This is the outside interface. interface FastEthernet0 ip address 14.24.120.1 255.255.0.0 ip nat outside ip inspect in2out out ip access-group 100 in no ip mroute-cache speed auto ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.120.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out FastEthernet0. ip nat inside source list 110 interface FastEthernet0 overload ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 no ip http server no ip http secure-server ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed. access-list 100 permit udp any host 14.24.116.1 eq 500 access-list 100 permit esp any host 14.24.116.1 access-list 100 permit gre any host 14.24.116.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.120.0 0.0.0.255 any ! ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! no scheduler allocate end 1720-A# |
Esta seção fornece informações que você pode usar para confirmar se sua configuração está funcionando adequadamente.
A Output Interpreter Tool (somente clientes registrados) oferece suporte a determinados comandos show, o que permite exibir uma análise da saída do comando show.
show crypto isakmp sa — Exibe o estado da associação de segurança ISAKMP (SA).
show crypto engine connections ative — Exibe o total de criptografia/descriptografia por SA.
show crypto ipsec sa — Exibe as estatísticas nos túneis ativos.
show ip route - Exibe a tabela de roteamento .
show ip eigrp neighbor—Exibe os vizinhos EIGRP.
show ip nhrp — Exibe o cache Next Hop Resolution Protocol (NHRP) de IP, opcionalmente limitado a entradas de cache dinâmico ou estático para uma interface específica.
show crypto socket — Exibe a tabela do soquete de criptografia entre o NHRP e o IPSec.
Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.
Observação: antes de emitir comandos debug, consulte Informações importantes sobre comandos debug.
debug crypto ipsec — Exibe eventos de IPSec.
debug crypto isakmp — Exibe mensagens sobre eventos de IKE.
debug crypto engine — Exibe informações a partir do cripto mecanismo.
debug crypto socket—Exibe informações sobre a tabela de soquetes entre NHRP e IPSec.
debug nhrp — Exibe informações sobre eventos NHRP.
debug nhrp packet — Exibe informações sobre pacotes NHRP.
debug tunnel protection—Exibe informações sobre túneis GRE dinâmicos.
Informações adicionais sobre Troubleshooting de IPSec podem ser encontradas em Troubleshooting de Segurança de IP - Compreendendo e Utilizando os comandos debug.
Revisão | Data de publicação | Comentários |
---|---|---|
1.0 |
14-Jan-2008 |
Versão inicial |