O Session Initiation Protocol (SIP) é um protocolo de sinalização usado para criar, gerenciar e encerrar sessões em uma rede baseada em IP. O SIP é um mecanismo de gerenciamento de chamadas. Ele também permite o estabelecimento da localização do usuário, fornece a negociação de recursos para que todos os participantes de uma sessão possam concordar com os recursos a serem suportados entre eles e permite que sejam feitas alterações nos recursos de uma sessão enquanto ela estiver em andamento.
O Session Description Protocol (SDP) é uma representação padrão para descrever fluxos de mídia para sessões multimídia. O próprio SDP não transporta mídia, mas negocia entre os pontos finais do tipo e formato de mídia. Os payloads do SDP são usados somente para chamadas de saída. Se houver chamadas de entrada, o Telefone IP seguirá o tipo de payload do chamador.
O objetivo deste documento é mostrar a você a configuração de tipos de payload SDP em telefones IP SPA300 e SPA500 Series.
Telefone IP SPA300 Series
Telefone IP SPA500 Series
Nota: No protocolo de sinalização do conjunto de telefones IP SPA300 ou SPA500 Series como SIP, use as teclas de navegação para ir para Device Administration > Call Control Settings > Signaling Protocol SIP.
Etapa 1. Faça login no utilitário de configuração da Web e escolha Admin Login > Advanced > Voice > SIP. A página Parâmetros SIP é aberta:
Etapa 2. Role para baixo até a área Tipos de payload SDP.
Etapa 3. Digite o número com o qual o remetente e o receptor devem concordar para o evento de sessão no campo AVT Dynamic Payload. O intervalo é de 96 a 127. O padrão é 101.
Etapa 4. Insira o número do codec usado para enviar uma mensagem SIP no campo Carga Dinâmica INFOREQ. O melhor intervalo é de 96 a 27. O padrão está em branco.
Nota: O número da Carga Dinâmica INFOREQ deve corresponder ao número da rede ou outro número de interlocutor configurado para ativar a Carga Dinâmica.
Etapa 5. Insira o Número do tipo de payload RTP no campo G726r16 Dynamic Payload. Esse é o número que representa o pacote transmitido pelo codec G.726r16. O intervalo é de 96 a 127. O padrão é 98.
Observação: o payload dinâmico G26r16 não se aplica ao SPA525G e SPA525G2.
Etapa 6. Insira o Número do tipo de payload RTP no campo G726r24 Dynamic Payload. Esse é o número que representa o pacote transmitido pelo codec G.726r24. O intervalo é de 96 a 127. O padrão é 97.
Observação: o payload dinâmico G26r24 não se aplica ao SPA525G e SPA525G2.
Passo 7. Insira o Número do tipo de payload RTP no campo G726r32 Dynamic Payload. Esse é o número que representa o pacote transmitido pelo codec G.726r32. O intervalo é de 0 a 268435455. O padrão é 2.
Etapa 8. Insira o Número do tipo de payload RTP no campo G726r40 Dynamic Payload. Esse é o número que representa o pacote transmitido pelo codec G.726r40. O intervalo é de 0 a 268435455. O padrão é 2.
Etapa 9. Insira o Número do tipo de payload do RTP no campo Payload Dinâmico do G729b. Esse é o número que representa o pacote transmitido pelo codec G.729b. O intervalo é de 0 a 268435455. O padrão é 99.
Etapa 10. Insira o tipo de payload dinâmico de RTP encapsulado no campo EncapRTP Dynamic Payload. O intervalo é de 0 a 268435455. O padrão é 112.
Etapa 11. Insira o valor que indica o RTP-Start-Loopback no campo RTP-Start-Loopback Dynamic. No RTP-Start-Loopback, um elemento de rede bloqueia a mídia da origem de loopback até que o loopback-mirror inicie a transmissão do pacote. O padrão é 113.
Etapa 12. Escolha o Codec de loopback inicial-RTP apropriado para converter um sinal de voz analógico em sinal de voz codificado digital na lista suspensa RTP-Start-Loopback Codec. O padrão é G711u.
G711u — Este é um esquema de modulação de código de pulso (PCM - Pulse Code Modulation). Isso usa codec mu-law, que melhora a relação sinal/ruído sem a exigência de mais dados adicionais. É usado nos Estados Unidos e no Japão.
G711a — Este é um esquema de modulação de código de pulso (PCM). Isso usa codec da lei A e é usado na maioria dos países do mundo.
G726-32 — Este é um esquema Adaptive Different Pulse Code Modulation (ADPM). Isso usa a-law e a mu-law e ajuda a reduzir a largura de banda.
G729a — Esta é uma extensão do G729 que usa a ACELP (Algebric Code Excitou a Predição Linear) para simplificar a complexidade e cortar o alto custo do G729. Requer menos potência computacional do que o G729.
G722 — Este é um esquema de modulação de código de pulso diferente adaptável de sub-banda (SB-ADPCM), que fornece taxas de dados de áudio de banda larga de 7 kHz para melhorar a qualidade da fala.
Etapa 13. Digite o nome do codec de transporte de vídeo de áudio (AVT) no campo AVT Codec Name. O padrão é telefone-evento.
Etapa 14. Digite o nome do codec G711u no campo G711u Codec Name. Este é um esquema de modulação de código de pulso (PCM - Pulse Code Modulation) que usa o codec mu-law para melhorar a relação sinal/ruído sem a necessidade de mais dados adicionais. É usado nos Estados Unidos e no Japão.O padrão é Pulse Code Modulation mu-law (PCMU).
Etapa 15. Insira o nome do codec G711a no campo G711a Codec Name (Nome do codec G711a). Este é um esquema de modulação de código de pulso (PCM - Pulse Code Modulation) que usa o codec A-law. É usado na maioria dos países do mundo.O padrão é Pulse Code Modulation A-law (PCMA).
Etapa 16. Digite o nome do codec G726r16 no campo G726r16 Codec Name. Este é um esquema Adaptive Differential Pulse Code Modulation (ADPCM) que usa 16 kbit por segundo. O padrão é G726-16.
Observação: o payload dinâmico G726r16 não se aplica ao SPA525G e SPA525G2.
Etapa 17. Digite o nome do codec G726r24 no campo G726r24 Codec Name. Este é um esquema Adaptive Differential Pulse Code Modulation (ADPCM) que usa 24 kbit por segundo. O padrão é G726-24.
Observação: o payload dinâmico G726-24 não se aplica ao SPA525G e SPA525G2.
Etapa 18. Digite o nome do código G726r32 no campo G726r32 Codec Name. Este é um esquema Adaptive Differential Pulse Code Modulation (ADPCM) que usa 32 kbit por segundo.O padrão é G726-32.
Etapa 19. Digite o nome do codec G726r40 no campo G726r40 Codec Name. Este é um esquema Adaptive Differential Pulse Code Modulation (ADPCM) que usa 40 kbit por segundo. O padrão é G726-40.
Observação: o payload dinâmico G726-40 não se aplica ao SPA525G e SPA525G2.
Etapa 20. Insira o nome do codec G729a no campo G729a Codec Name (Nome do codec G729a). Esta é uma extensão do G729 que usa a ACELP (Algebric Code Excitated Linear Pretioning) para simplificar a complexidade e reduzir o alto custo do G729. Requer menos potência computacional do que o G729.O padrão é G729a.
Etapa 21. Digite o nome do codec G729b no campo G729b Codec Name. Esta é uma extensão do G729 para fornecer suporte à fala e ao áudio de banda larga.O padrão é G729ab.
Etapa 22. Digite o nome do codec G722 no campo G722 Codec Name. Este é um codec que oferece suporte a áudio de banda larga de 7 kHz. O padrão é G722.
Etapa 23. Digite o nome do código G723 no campo G723 Codec Name. Esta é uma extensão da G721 que usa Adaptive Differential Pulse Code Modulation (ADPCM) para fornecer qualidade de voz de 300 Hz a 3400 Hz. O padrão é G723.
Observação: o payload dinâmico G723 não se aplica ao SPA525G e SPA525G2.
Etapa 24. Digite o nome do codec EncapRTP no campo EncapRTP Codec Name. Este é o nome encapsulado do Real-Time Protocol . O padrão é encaprtp.
Etapa 25. Clique em Enviar todas as alterações para salvar as configurações.